DSPIC33FJ16GS504-I/TL [MICROCHIP]
16-BIT, FLASH, 50 MHz, MICROCONTROLLER, PQCC44, 6 X 6 MM, 0.90 MM HEIGHT, LEAD FREE, PLASTIC, VTLA-44;型号: | DSPIC33FJ16GS504-I/TL |
厂家: | MICROCHIP |
描述: | 16-BIT, FLASH, 50 MHz, MICROCONTROLLER, PQCC44, 6 X 6 MM, 0.90 MM HEIGHT, LEAD FREE, PLASTIC, VTLA-44 时钟 外围集成电路 |
文件: | 总398页 (文件大小:3368K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04
16-Bit Digital Signal Controllers (up to 16-Kbyte Flash and up to
2-Kbyte SRAM) with High-Speed PWM, ADC and Comparators
Operating Conditions
Advanced Analog Features (Continued)
• 3.0V to 3.6V, -40ºC to +150ºC, DC to 20 MIPS
• 3.0V to 3.6V, -40ºC to +125ºC, DC to 40 MIPS
• 3.0V to 3.6V, -40ºC to +85ºC, DC to 50 MIPS
• Up to Four High-Speed Comparators with Direct
Connection to the PWM module:
- Programmable references with 1024 voltage points
Core: 16-Bit dsPIC33F CPU
Timers/Output Compare/Input Capture
• Three General Purpose Timers:
• Code-Efficient (C and Assembly) Architecture
• Two 40-Bit Wide Accumulators
• Single-Cycle (MAC/MPY) with Dual Data Fetch
• Single-Cycle Mixed-Sign MUL plus Hardware Divide
• 32-Bit Multiply Support
- Three 16-bit and one 32-bit timer/counter
• Two Output Compare (OC) modules
• Two Input Capture (IC) modules
• Peripheral Pin Select (PPS) to allow Function Remap
Communication Interfaces
• UART module (12.5 Mbps):
- With support for LIN/J2602 protocols and IrDA
Clock Management
• ±2.0% Internal Oscillator
®
• Programmable PLLs and Oscillator Clock Sources
• Fail-Safe Clock Monitor (FSCM)
• Independent Watchdog Timer (WDT)
• Fast Wake-up and Start-up
• 4-Wire SPI module
2
• I C™ module (up to 1 Mbaud) with SMBus Support
• PPS to allow Function Remap
Input/Output
• Sink/Source 18 mA on 8 Pins, 10 mA on 10 Pins
and 6 mA on 17 Pins
Power Management
• Low-Power Management modes (Sleep, Idle, Doze)
• Integrated Power-on Reset and Brown-out Reset
• 5V Tolerant Pins
• Selectable Open-Drain and Pull-ups
• External Interrupts on up to 30 I/O Pins
High-Speed PWM
• Up to Four PWM Pairs with Independent Timing
• Dead Time for Rising and Falling Edges
• 1.04 ns PWM Resolution
• PWM Support for:
- DC/DC, AC/DC, Inverters, PFC and Lighting
• Programmable Fault Inputs
Qualification and Class B Support
• AEC-Q100 REVG (Grade 1, -40ºC to +125ºC)
• AEC-Q100 REVG (Grade 0, -40ºC to +150ºC)
• Class B Safety Library, IEC 60730, VDE Certified
• 6x6x0.5 mm UQFN Package Designed and
Optimized to ease IPC9592A 2nd Level Temperature
Cycle Qualification
• Flexible Trigger Configurations for ADC Conversions
Advanced Analog Features
• ADC module:
Debugger Development Support
• In-Circuit and In-Application Programming
• Two Breakpoints
• IEEE 1149.2-Compatible (JTAG) Boundary Scan
• Trace and Run-Time Watch
- 10-bit resolution with up to 2 Successive Approximation
Register (SAR) converters (4 Msps) and up to
six Sample-and-Hold (S&H) circuits
- Up to 12 input channels grouped into six conversion
pairs, plus two voltage reference monitoring inputs
- Dedicated result buffer for each analog channel
• Flexible and Independent ADC Trigger Sources
2008-2014 Microchip Technology Inc.
DS70000318G-page 1
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
dsPIC33FJ06GS101/X02 AND
dsPIC33FJ16GSX02/X04 PRODUCT
FAMILIES
The device names, pin counts, memory sizes and
peripheral availability of each device are listed below.
The following pages show their pinout diagrams.
TABLE 1:
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 CONTROLLER FAMILIES
Remappable Peripherals
ADC
Device
(1)
dsPIC33FJ06GS101 18
dsPIC33FJ06GS102 28
6
6
256
8
2
2
0
0
1
1
1
1
1
1
2x2
0
0
3
3
0
0
1
1
1
1
3
3
6
6
13
SOIC
256 16
1K 16
2K 16
2K 30
2K 16
2x2
21 SPDIP,
SOIC,
QFN-S
dsPIC33FJ06GS202 28
dsPIC33FJ16GS402 28
dsPIC33FJ16GS404 44
dsPIC33FJ16GS502 28
6
2
3
3
3
1
2
2
2
1
2
2
2
1
1
1
1
1
1
1
1
2x2
3x2
3x2
2
0
0
4
3
3
3
3
1
0
0
1
1
1
1
1
1
1
1
2
3
4
4
6
6
8
8
8
21 SPDIP,
SOIC,
QFN-S
16
16
16
21 SPDIP,
SOIC,
QFN-S
35
QFN,
TQFP,
VTLA
(1)
4x2
4x2
21 SPDIP,
SOIC,
QFN-S,
UQFN
(1)
dsPIC33FJ16GS504 44
16
2K 30
3
2
2
1
1
4
3
1
1
2
6
12 35
QFN,
TQFP,
VTLA
Note 1: The PWM4H:PWM4L pins are remappable.
2: The PWM Fault pins and PWM synchronization pins are remappable.
3: Only two out of three interrupts are remappable.
DS70000318G-page 2
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Pin Diagrams
= Pins are up to 5V tolerant
18-Pin SOIC
MCLR
AN0/RA0
1
2
3
4
5
18
17
16
15
14
VDD
VSS
AN1/RA1
PWM1L/RA3
PWM1H/RA4
AN2/RA2
AN3/RP0(1)/CN0/RB0
OSC1/CLKI/AN6/RP1(1)/CN1/RB1
OSC2/CLKO/AN7/RP2(1)/CN2/RB2
TCK/PGED2/INT0/RP3(1)/CN3/RB3
TMS/PGEC2/RP4(1)/CN4/RB4
VCAP
VSS
6
13
PGEC1/SDA1/RP7(1)/CN7/RB7
PGED1/TDI/SCL1/RP6(1)/CN6/RB6
TDO/RP5(1)/CN5/RB5
7
8
12
11
9
10
= Pins are up to 5V tolerant
28-Pin SOIC, SPDIP
MCLR
AN0/RA0
AN1/RA1
1
28
AVDD
AVSS
PWM1L/RA3
PWM1H/RA4
2
3
4
5
6
7
8
27
26
25
24
23
22
21
AN2/RA2
AN3/RP0(1)/CN0/RB0
AN4/RP9(1)/CN9/RB9
PWM2L/RP14(1)/CN14/RB14
PWM2H/RP13(1)/CN13/RB13
RP12(1)/CN12/RB12
RP11(1)/CN11/RB11
AN5/RP10(1)/CN10/RB10
VSS
OSC1/CLKIN/RP1(1)/CN1/RB1
OSC2/CLKO/RP2(1)/CN2/RB2
TCK/PGED2/INT0/RP3(1)/CN3/RB3
TMS/PGEC2/RP4(1)/CN4/RB4
VDD
9
20
19
18
17
16
15
VCAP
VSS
10
11
12
13
14
PGEC1/SDA/RP7(1)/CN7/RB7
PGED1/TDI/SCL/RP6(1)/CN6/RB6
TDO/RP5(1)/CN5/RB5
PGEC3/RP15(1)/CN15/RB15
PGED3/RP8(1)/CN8/RB8
= Pins are up to 5V tolerant
28-Pin SPDIP, SOIC
MCLR
AN0/CMP1A/RA0
AN1/CMP1B/RA1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
AVDD
AVSS
PWM1L/RA3
PWM1H/RA4
AN2/CMP1C/CMP2A/RA2
AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0
AN4/CMP2C/RP9(1)/CN9/RB9
AN5/CMP2D/RP10(1)/CN10/RB10
VSS
PWM2L/RP14(1)/CN14/RB14
PWM2H/RP13(1)/CN13/RB13
TCK/RP12(1)/CN12/RB12
TMS/RP11(1)/CN11/RB11
OSC1/CLKIN/RP1(1)/CN1/RB1
OSC2/CLKO/RP2(1)/CN2/RB2
PGED2/DACOUT/INT0/RP3(1)/CN3/RB3
PGEC2/EXTREF/RP4(1)/CN4/RB4
VDD
VCAP
VSS
PGEC1/SDA/RP7(1)/CN7/RB7
PGED1/TDI/SCL/RP6(1)/CN6/RB6
TDO/RP5(1)/CN5/RB5
PGEC3/RP15(1)/CN15/RB15
PGED3/RP8(1)/CN8/RB8
Note 1: The RPn pins can be used by any remappable peripheral. See Table 1 for the list of available
peripherals.
2008-2014 Microchip Technology Inc.
DS70000318G-page 3
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Pin Diagrams (Continued)
28-Pin SPDIP, SOIC
= Pins are up to 5V tolerant
MCLR
AN0/RA0
AN1/RA1
1
2
3
4
5
6
7
8
28
27
26
25
24
23
22
21
AVDD
AVSS
PWM1L/RA3
PWM1H/RA4
AN2/RA2
AN3/RP0(1)/CN0/RB0
AN4/RP9(1)/CN9/RB9
AN5/RP10(1)/CN10/RB10
VSS
PWM2L/RP14(1)/CN14/RB14
PWM2H/RP13(1)/CN13/RB13
TCK/PWM3L/RP12(1)/CN12/RB12
TMS/PWM3H/RP11(1)/CN11/RB11
OSC1/CLKIN/AN6/RP1(1)/CN1/RB1
OSC2/CLKO/AN7/RP2(1)/CN2/RB2
PGED2/INT0/RP3(1)/CN3/RB3
PGEC2/RP4(1)/CN4/RB4
VDD
9
20
19
18
17
16
15
VCAP
VSS
10
11
12
13
14
PGEC1/SDA/RP7(1)/CN7/RB7
PGED1/TDI/SCL/RP6(1)/CN6/RB6
TDO/RP5(1)/CN5/RB5
PGEC3/RP15/CN15/RB15
PGED3/RP8(1)/CN8/RB8
= Pins are up to 5V tolerant
28-Pin SPDIP, SOIC
MCLR
AN0/CMP1A/RA0
AN1/CMP1B/RA1
1
2
3
4
5
6
7
8
28
27
26
25
24
23
22
21
AVDD
AVSS
PWM1L/RA3
PWM1H/RA4
AN2/CMP1C/CMP2A/RA2
AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0
AN4/CMP2C/CMP3A/RP9(1)/CN9/RB9
AN5/CMP2D/CMP3B/RP10(1)/CN10/RB10
VSS
PWM2L/RP14(1)/CN14/RB14
PWM2H/RP13(1)/CN13/RB13
TCK/PWM3L/RP12(1)/CN12/RB12
TMS/PWM3H/RP11(1)/CN11/RB11
OSC1/CLKIN/AN6/CMP3C/CMP4A/RP1(1)/CN1/RB1
OSC2/CLKO/AN7/CMP3D/CMP4B/RP2(1)/CN2/RB2
PGED2/DACOUT/INT0/RP3(1)/CN3/RB3
PGEC2/EXTREF/RP4(1)/CN4/RB4
VDD
9
20
19
18
17
16
15
VCAP
VSS
10
11
12
13
14
PGEC1/SDA/RP7(1)/CN7/RB7
PGED1/TDI/SCL/RP6(1)/CN6/RB6
TDO/RP5(1)/CN5/RB5
PGEC3/RP15(1)/CN15/RB15
CN8/RB8/PGED3/RP8(1)/CN8/RB8
Note 1: The RPn pins can be used by any remappable peripheral. See Table 1 for the list of available
peripherals.
DS70000318G-page 4
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Pin Diagrams (Continued)
28-Pin QFN-S(2)
= Pins are up to 5V tolerant
28272625242322
PWM2L/RP14(1)/CN14/RB14
AN2/RA2
AN3/RP0(1)/CN0/RB0
AN4/RP9(1)/CN9/RB9
AN5/RP10(1)/CN10/RB10
VSS
1
2
3
4
5
6
7
21
20 PWM2H/RP13(1)/CN13/RB13
19 TCK/RP12(1)/CN12/RB12
TMS/RP11(1)/CN11/RB11
dsPIC33FJ06GS102 18
17 VCAP
16
15
OSC1/CLKIN/RP1(1)/CN1/RB1
OSC2/CLKO/RP2(1)/CN2/RB2
VSS
PGEC1/SDA/RP7(1)/CN7/RB7
8
9 10 1112 13 14
= Pins are up to 5V tolerant
28-Pin QFN-S
28272625242322
PWM2L/RP14(1)/CN14/RB14
AN2/CMP1C/CMP2A/RA2
1
2
3
4
5
6
7
21
AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0
AN4/CMP2C/RP9(1)/CN9/RB9
AN5/CMP2D/RP10(1)/CN10/RB10
VSS
20 PWM2H/RP13(1)/CN13/RB13
19
TCK/RP12(1)/CN12/RB12
TMS/RP11(1)/CN11/RB11
dsPIC33FJ06GS202 18
VCAP
VSS
17
16
15
OSC1/CLKIN/RP1(1)/CN1/RB1
OSC2/CLKO/RP2(1)/CN2/RB2
PGEC1/SDA/RP7(1)/CN7/RB7
8
9 10 111213 14
Note 1: The RPn pins can be used by any remappable peripheral. See Table 1 for the list of available peripherals.
2: The metal plane at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
2008-2014 Microchip Technology Inc.
DS70000318G-page 5
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Pin Diagrams (Continued)
28-Pin QFN-S(2)
= Pins are up to 5V tolerant
28272625242322
PWM2L/RP14(1)/CN14/RB14
AN2/RA2
1
2
3
4
5
6
7
21
20 PWM2H/RP13(1)/CN13/RB13
19
AN3/RP0(1)/CN0/RB0
AN4/RP9(1)/CN9/RB9
AN5/RP10(1)/CN10/RB10
VSS
TCK/PWM3L/RP12(1)/CN12/RB12
TMS/PWM3H/RP11(1)/CN11/RB11
dsPIC33FJ16GS402 18
17 VCAP
16
15
OSC1/CLKIN/AN6/RP1(1)/CN1/RB1
OSC2/CLKO/AN7/RP2(1)/CN2/RB2
VSS
PGEC1/SDA/RP7(1)/CN7/RB7
8
9 1011 121314
28-Pin QFN-S, UQFN(2,3)
= Pins are up to 5V tolerant
28272625242322
PWM2L/RP14(1)/CN14/RB14
AN2/CMP1C/CMP2A/RA2
1
2
3
4
5
6
7
21
20 PWM2H/RP13(1)/CN13/RB13
AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0
AN4/CMP2C/CMP3A/RP9(1)/CN9/RB9
AN5/CMP2D/CMP3B/RP10(1)/CN10/RB10
VSS
19
TCK/PWM3L/RP12(1)/CN12/RB12
TMS/PWM3H/RP11(1)/CN11/RB11
VCAP
dsPIC33FJ16GS502 18
17
16 VSS
15
OSC1/CLKIN/AN6/CMP3C/CMP4A/RP1(1)/CN1/RB1
OSC2/CLKO/AN7/CMP3D/CMP4B/RP2(1)/CN2/RB2
PGEC1/SDA/RP7(1)/CN7/RB7
8
9 10 1112 13 14
Note 1: The RPn pins can be used by any remappable peripheral. See Table 1 for the list of available peripherals.
2: The metal plane at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
3: This package is available only in Extended temperature and not Industrial temperature (applies to
dsPIC33FJ16GS502 UQFN package only).
DS70000318G-page 6
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Pin Diagrams (Continued)
44-Pin VTLA(2)
= Pins are up to 5V tolerant
OSC2/CLKO/AN7/RP2(1)/CN2/RB2
44 43 42 41 40 39 38 37 36 35 34 33
PGEC1/SDA/RP7(1)/CN7/RB7
1
2
OSC1/CLKI/AN6/RP1(1)/CN1/RB1
RP17(1)/CN17/RC1
32
RP20(1)/CN20/RC4
RP21(1)/CN21/RC5
RP22(1)/CN22/RC6
RP19(1)/CN19/RC3
VSS
31
3
30
VSS
4
VDD
29
5
RP26(1)/CN26/RC10
RP25(1)/CN25/RC9
AN5/RP10(1)/CN10/RB10
AN4/RP9(1)/CN9/RB9
AN3/RP0(1)/CN0/RB0
AN2/RA2
28
dsPIC33FJ16GS404
6
27
VCAP
7
26
TMS/PWM3H/RP11(1)/CN11/RB11
TCK/PWM3L/RP12(1)/CN12/RB12
PWM2H/RP13(1)/CN13/RB13
8
25
24
9
23
10
PWM2L/RP14(1)/CN14/RB14 11 12 13 14 15 16 17 18 19
20 21 22
Note 1: The RPn pins can be used by any remappable peripheral. See Table 1 for the list of available peripherals.
2: The metal plane at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
2008-2014 Microchip Technology Inc.
DS70000318G-page 7
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Pin Diagrams (Continued)
44-Pin VTLA(2)
= Pins are up to 5V tolerant
OSC2/CLKO/AN7/CMP3D/CMP4B/RP2(1)/CN2/RB2
44 43 42 41 40 39 38 37 36 35 34 33
PGEC1/SDA/RP7(1)/CN7/RB7
RP20(1)/CN20/RC4
32 OSC1/CLKI/AN6/CMP3C/CMP4A/RP1(1)/CN1/RB1
1
AN8/CMP4C/RP17(1)/CN17/RC1
31
2
3
RP21(1)/CN21/RC5
30
VSS
RP22(1)/RN22/RC6
4
29 VDD
RP19(1)/CN19/RC3
5
AN10/RP26(1)/CN26/RC10
28
27
26
25
24
23
22
dsPIC33FJ16GS504
6
AN11/RP25(1)/CN25/RC9
VSS
AN5/CMP2D/CMP3B/RP10(1)/CN10/RB10
AN4/CMP2C/CMP3A/RP9(1)/CN9/RB9
AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0
AN2/CMP1C/CMP2A/RA2
VCAP
7
TMS/PWM3H/RP11(1)/CN11/RB11
TCK/PWM3L/RP12(1)/CN12/RB12
PWM2H/RP13(1)/CN13/RB13
8
9
10
PWM2L/RP14(1)/CN14/RB14 11 12 13 14 15 16 17 18 19
20 21
Note 1: The RPn pins can be used by any remappable peripheral. See Table 1 for the list of available peripherals.
2: The metal plane at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
DS70000318G-page 8
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Pin Diagrams (Continued)
44-Pin QFN(2)
= Pins are up to 5V tolerant
44 43 42 41 40 39 38 37 36 35 34
OSC2/CLKO/AN7/RP2(1)/CN2/RB2
OSC1/CLKI/AN6/RP1(1)/CN1/RB1
RP17(1)/CN17/RC1
PGEC1/SDA/RP7(1)/CN7/RB7
RP20(1)/CN20/RC4
1
2
33
32
31
30
29
28
27
26
25
24
23
RP21(1)/CN21/RC5
RP22(1)/CN22/RC6
RP19(1)/CN19/RC3
3
VSS
4
VDD
5
dsPIC33FJ16GS404
RP26(1)/CN26/RC10
RP25(1)/CN25/RC9
AN5/RP10(1)/CN10/RB10
AN4/RP9(1)/CN9/RB9
AN3/RP0(1)/CN0/RB0
VSS
6
VCAP
7
TMS/PWM3H/RP11(1)/CN11/RB11
TCK/PWM3L/RP12(1)/CN12/RB12
PWM2H/RP13(1)/CN13/RB13
PWM2L/RP14(1)/CN14/RB14
8
9
10
11
AN2/RA2
12 13 14 15 16 17 18 19 20 21 22
Note 1: The RPn pins can be used by any remappable peripheral. See Table 1 for the list of available peripherals.
2: The metal plane at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
2008-2014 Microchip Technology Inc.
DS70000318G-page 9
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Pin Diagrams (Continued)
44-Pin QFN(2)
= Pins are up to 5V tolerant
44 43 42 41 40 39 38 37 36 35 34
PGEC1/SDA/RP7(1)/CN7/RB7
OSC2/CLKO/AN7/CMP3D/CMP4B/RP2(1)/CN2/RB2
OSC1/CLKI/AN6/CMP3C/CMP4A/RP1(1)/CN1/RB1
AN8/CMP4C/RP17(1)/CN17/RC1
1
2
33
32
31
30
29
28
27
26
25
24
23
RP20(1)/CN20/RC4
RP21(1)/CN21/RC5
RP22(1)/RN22/RC6
RP19(1)/CN19/RC3
3
4
VSS
5
VDD
dsPIC33FJ16GS504
AN10/RP26(1)/CN26/RC10
AN11/RP25(1)/CN25/RC9
VSS
6
VCAP
7
TMS/PWM3H/RP11(1)/CN11/RB11
TCK/PWM3L/RP12(1)/CN12/RB12
PWM2H/RP13(1)/CN13/RB13
PWM2L/RP14(1)/CN14/RB14
AN5/CMP2D/CMP3B/RP10(1)/CN10/RB10
AN4/CMP2C/CMP3A/RP9(1)/CN9/RB9
AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0
AN2/CMP1C/CMP2A/RA2
8
9
10
11
12 13 14 15 16 17 18 19 20 21 22
Note 1: The RPn pins can be used by any remappable peripheral. See Table 1 for the list of available peripherals.
2: The metal plane at the bottom of the device is not connected to any pins and is recommended to be
connected to VSS externally.
DS70000318G-page 10
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Pin Diagrams (Continued)
44-Pin TQFP
= Pins are up to 5V tolerant
OSC2/CLKO/AN7/RP2(1)/CN2/RB2
OSC1/CLKI/AN6/RP1(1)/CN1/RB1
RP17(1)/CN17/RC1
VSS
PGEC1/SDA/RP7(1)/CN7/RB7
RP20(1)/CN20/RC4
33
32
31
30
29
28
1
2
3
4
5
6
7
8
9
RP21(1)/CN21/RC5
RP22(1)/CN22/RC6
RP19(1)/CN19/RC3
VDD
dsPIC33FJ16GS404
RP26(1)/CN26/RC10
RP25(1)/CN25/RC9
VSS
VCAP
27
26
AN5/RP10(1)/CN10/RB10
AN4/RP9(1)/CN9/RB9
AN3/RP0(1)/CN0/RB0
AN2/RA2
TMS/PWM3H/RP11(1)/CN11/RB11
TCK/PWM3L/RP12(1)/CN12/RB12
PWM2H/RP13(1)/CN13/RB13
PWM2L/RP14(1)/CN14/RB14
25
24
23
10
11
Note 1: The RPn pins can be used by any remappable peripheral. See Table 1 for the list of available peripherals.
2008-2014 Microchip Technology Inc.
DS70000318G-page 11
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Pin Diagrams (Continued)
44-Pin TQFP
= Pins are up to 5V tolerant
OSC2/CLKO/AN7/CMP3D/CMP4B/RP2(1)/CN2/RB2
OSC1/CLKI/AN6/CMP3C/CMP4A/RP1(1)/CN1/RB1
AN8/CMP4C/RP17(1)/CN17/RC1
PGEC1/SDA/RP7(1)/CN7/RB7
33
1
RP20(1)/CN20/RC4
32
2
RP21(1)/CN21/RC5
31
3
RP22(1)/CN22/RC6
RP19(1)/CN19/RC3
VSS
30
29
28
4
5
6
7
8
9
VDD
dsPIC33FJ16GS504
AN10/RP26(1)/CN26/RC10
AN11/RP25(1)/CN25/RC9
AN5/CMP2D/CMP3B/RP10(1)/CN10/RB10
AN4/CMP2C/CMP3A/RP9(1)/CN9/RB9
AN3/CMP1D/CMP2B/RP0(1)/CN0/RB0
AN2/CMP1C/CMP2A/RA2
VSS
VCAP
27
26
TMS/PWM3H/RP11(1)/CN11/RB11
TCK/PWM3L/RP12(1)/CN12/RB12
PWM2H/RP13(1)/CN13/RB13
PWM2L/RP14(1)/CN14/RB14
25
24
23
10
11
Note 1: The RPn pins can be used by any remappable peripheral. See Table 1 for the list of available peripherals.
DS70000318G-page 12
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Table of Contents
dsPIC33FJ06GS101/X02 AND dsPIC33FJ16GSX02/X04 Product Families......................................................................................... 2
1.0 Device Overview ........................................................................................................................................................................ 17
2.0 Guidelines for Getting Started with 16-bit Digital Signal Controllers .......................................................................................... 21
3.0 CPU............................................................................................................................................................................................ 31
4.0 Memory Organization................................................................................................................................................................. 43
5.0 Flash Program Memory.............................................................................................................................................................. 83
6.0 Resets ....................................................................................................................................................................................... 89
7.0 Interrupt Controller ..................................................................................................................................................................... 97
8.0 Oscillator Configuration ......................................................................................................................................................... 135
9.0 Power-Saving Features............................................................................................................................................................ 147
10.0 I/O Ports ................................................................................................................................................................................... 155
11.0 Timer1 ...................................................................................................................................................................................... 183
12.0 Timer2/3 Features ................................................................................................................................................................... 185
13.0 Input Capture............................................................................................................................................................................ 191
14.0 Output Compare....................................................................................................................................................................... 193
15.0 High-Speed PWM..................................................................................................................................................................... 197
16.0 Serial Peripheral Interface (SPI)............................................................................................................................................... 219
2
17.0 Inter-Integrated Circuit (I C™) ................................................................................................................................................. 225
18.0 Universal Asynchronous Receiver Transmitter (UART)........................................................................................................... 233
19.0 High-Speed 10-bit Analog-to-Digital Converter (ADC)............................................................................................................. 239
20.0 High-Speed Analog Comparator .............................................................................................................................................. 263
21.0 Special Features ...................................................................................................................................................................... 267
22.0 Instruction Set Summary.......................................................................................................................................................... 275
23.0 Development Support............................................................................................................................................................... 283
24.0 Electrical Characteristics.......................................................................................................................................................... 287
25.0 High-Temperature Electrical Characteristics............................................................................................................................ 333
26.0 50 MIPS Electrical Characteristics ........................................................................................................................................... 341
27.0 DC and AC Device Characteristics Graphs.............................................................................................................................. 347
28.0 Packaging Information.............................................................................................................................................................. 351
The Microchip Web Site..................................................................................................................................................................... 393
Customer Change Notification Service .............................................................................................................................................. 393
Customer Support.............................................................................................................................................................................. 393
Product Identification System ............................................................................................................................................................ 395
2008-2014 Microchip Technology Inc.
DS70000318G-page 13
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at docerrors@microchip.com. We welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000000A is version A of document DS30000000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
•
•
Microchip’s Worldwide Web site; http://www.microchip.com
Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are
using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
DS70000318G-page 14
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Referenced Sources
This device data sheet is based on the following
individual chapters of the “dsPIC33/PIC24 Family Ref-
erence Manual”. These documents should be
considered as the primary reference for the operation
of a particular module or device feature.
Note:
To access the documents listed below,
browse to the documentation section
of the dsPIC33FJ16GS504 product
page of the Microchip web site
(www.microchip.com).
In addition to parameters, features, and
other documentation, the resulting page
provides links to the related family
reference manual sections.
• “Introduction” (DS70197)
• “CPU” (DS70204)
• “Data Memory” (DS70202)
• “Program Memory” (DS70203)
•
“Flash Programming” (DS70191)
• “Reset” (DS70192)
• “Watchdog Timer (WDT) and Power-Saving Modes” (DS70196)
• “I/O Ports” (DS70193)
• “Timers” (DS70205)
• “Input Capture” (DS70198)
• “Output Compare” (DS70005157)
• “Analog-to-Digital Converter (ADC)” (DS70621)
• “UART” (DS70188)
• “Serial Peripheral Interface (SPI)” (DS70206)
• “Inter-Integrated Circuit™ (I2C™)” (DS70000195)
• “CodeGuard™ Security (DS70199)
• “Programming and Diagnostics” (DS70207)
• “Device Configuration” (DS70194)
• “Interrupts (Part IV)” (DS70300)
• “Oscillator (Part IV)” (DS70307)
• “High- Speed PWM Module” (DS70000323)
• “High-Speed 10-Bit ADC” (DS70000321)
• “High-Speed Analog Comparator” (DS70296)
• “Oscillator (Part VI)” (DS70644)
2008-2014 Microchip Technology Inc.
DS70000318G-page 15
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 16
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
This document contains device-specific information for
the following dsPIC33F Digital Signal Controller (DSC)
devices:
1.0
DEVICE OVERVIEW
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a compre-
hensive reference source. To complement
the information in this data sheet, refer to
the “dsPIC33F/PIC24H Family Reference
Manual”. Please see the Microchip web
site (www.microchip.com) for the latest
“dsPIC33F/PIC24H Family Reference
Manual” sections.
• dsPIC33FJ06GS101
• dsPIC33FJ06GS102
• dsPIC33FJ06GS202
• dsPIC33FJ16GS402
• dsPIC33FJ16GS404
• dsPIC33FJ16GS502
• dsPIC33FJ16GS504
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices contain extensive Digital Signal Processor
(DSP) functionality with a high-performance, 16-bit
microcontroller (MCU) architecture.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
Figure 1-1 shows a general block diagram of the core and
peripheral modules in the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 devices. Table 1-1 lists the
functionsofthevariouspinsshowninthepinoutdiagrams.
2008-2014 Microchip Technology Inc.
DS70000318G-page 17
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 1-1:
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 BLOCK DIAGRAM
PSV & Table
Data Access
Control Block
Y Data Bus
X Data Bus
Interrupt
Controller
PORTA
16
16
16
8
16
Data Latch
Data Latch
X RAM
23
PCU PCH PCL
Program Counter
Y RAM
PORTB
PORTC
23
Address
Latch
Address
Latch
Loop
Control
Logic
Stack
Control
Logic
16
23
16
16
Address Generator Units
Address Latch
Program Memory
Data Latch
EA MUX
Remappable
Pins
ROM Latch
24
16
16
Instruction
Decode &
Control
Instruction Reg
16
Control Signals
to Various Blocks
DSP Engine
16 x 16
Power-up
Timer
W Register Array
Divide Support
16
Timing
Generation
OSC2/CLKO
OSC1/CLKI
Oscillator
Start-up Timer
FRC/LPRC
Oscillators
Power-on
Reset
16-Bit ALU
Watchdog
Timer
16
Brown-out
Reset
Voltage
Regulator
VCAP
VDD, VSS MCLR
OC1
OC2
PWM
4 x 2
Timers
1-3
UART1
ADC1
CNx
Analog
Comparators 1-4
IC1
IC2
I2C1
SPI1
Note:
Not all pins or features are implemented on all device pinout configurations. See pinout diagrams for the specific pins and
features present on each device.
DS70000318G-page 18
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 1-1:
Pin Name
AN0-AN11
PINOUT I/O DESCRIPTIONS
Pin
Type
Buffer
Type
PPS
Capable
Description
I
I
Analog
No
No
Analog input channels
CLKI
ST/CMOS
External clock source input. Always associated with OSC1 pin
function.
CLKO
O
—
No
Oscillator crystal output. Connects to crystal or resonator in Crystal
Oscillator mode. Optionally functions as CLKO in RC and EC
modes. Always associated with OSC2 pin function.
OSC1
OSC2
I
ST/CMOS
—
No
No
Oscillator crystal input. ST buffer when configured in RC mode;
CMOS otherwise.
Oscillator crystal output. Connects to crystal or resonator in Crystal
Oscillator mode. Optionally functions as CLKO in RC and EC
modes.
I/O
CN0-CN29
IC1-IC2
I
I
ST
ST
No
Change Notification inputs. Can be software programmed for
internal weak pull-ups on all inputs.
Yes
Capture Inputs 1/2.
OCFA
OC1-OC2
I
O
ST
—
Yes
Yes
Compare Fault A input (for Compare Channels 1 and 2)
Compare Outputs 1 through 2.
INT0
INT1
INT2
I
I
I
ST
ST
ST
No
Yes
Yes
External Interrupt 0.
External Interrupt 1.
External Interrupt 2.
RA0-RA4
I/O
I/O
I/O
I/O
ST
ST
ST
ST
No
No
No
No
PORTA is a bidirectional I/O port.
PORTB is a bidirectional I/O port.
PORTC is a bidirectional I/O port.
Remappable I/O pins.
RB0-RB15
RC0-RC13
RP0-RP29
T1CK
T2CK
T3CK
I
I
I
ST
ST
ST
Yes
Yes
Yes
Timer1 external clock input.
Timer2 external clock input.
Timer3 external clock input.
U1CTS
U1RTS
U1RX
I
O
I
ST
—
ST
—
Yes
Yes
Yes
Yes
UART1 Clear-To-Send.
UART1 Ready-To-Send.
UART1 receive.
U1TX
O
UART1 transmit.
SCK1
SDI1
SDO1
SS1
I/O
I
O
ST
ST
—
Yes
Yes
Yes
Yes
Synchronous serial clock input/output for SPI1.
SPI1 data in.
SPI1 data out.
I/O
ST
SPI1 slave synchronization or frame pulse I/O.
SCL1
SDA1
I/O
I/O
ST
ST
No
No
Synchronous serial clock input/output for I2C1.
Synchronous serial data input/output for I2C1.
TMS
TCK
TDI
I
I
I
TTL
TTL
TTL
—
No
No
No
No
JTAG Test mode select pin.
JTAG test clock input pin.
JTAG test data input pin.
JTAG test data output pin.
TDO
O
Legend: CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
TTL = Transistor-Transistor Logic
Analog = Analog input
P = Power
PPS = Peripheral Pin Select
I = Input
O = Output
2008-2014 Microchip Technology Inc.
DS70000318G-page 19
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 1-1:
Pin Name
PINOUT I/O DESCRIPTIONS (CONTINUED)
Pin
Buffer
Type
PPS
Description
Type
Capable
CMP1A
CMP1B
CMP1C
CMP1D
CMP2A
CMP2B
CMP2C
CMP2D
CMP3A
CMP3B
CMP3C
CMP3D
CMP4A
CMP4B
CMP4C
CMP4D
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Comparator 1 Channel A.
Comparator 1 Channel B.
Comparator 1 Channel C.
Comparator 1 Channel D.
Comparator 2 Channel A.
Comparator 2 Channel B.
Comparator 2 Channel C.
Comparator 2 Channel D.
Comparator 3 Channel A.
Comparator 3 Channel B.
Comparator 3 Channel C.
Comparator 3 Channel D.
Comparator 4 Channel A.
Comparator 4 Channel B.
Comparator 4 Channel C.
Comparator 4 Channel D.
DACOUT
O
O
I
—
—
No
Yes
No
DAC output voltage.
ACMP1-ACMP4
EXTREF
DAC trigger to PWM module.
Analog
—
External voltage reference input for the reference DACs.
REFCLKO
O
Yes
REFCLKO output signal is a postscaled derivative of the system
clock.
FLT1-FLT8
SYNCI1-SYNCI2
SYNCO1
PWM1L
PWM1H
PWM2L
PWM2H
PWM3L
PWM3H
PWM4L
I
I
ST
ST
—
—
—
—
—
—
—
—
—
Yes
Yes
Yes
No
No
No
No
No
No
Yes
Yes
Fault Inputs to PWM module.
External synchronization signal to PWM master time base.
PWM master time base for external device synchronization.
PWM1 low output.
PWM1 high output.
PWM2 low output.
PWM2 high output.
PWM3 low output.
PWM3 high output.
PWM4 low output.
O
O
O
O
O
O
O
O
O
PWM4H
PWM4 high output.
PGED1
PGEC1
I/O
I
ST
ST
No
No
Data I/O pin for programming/debugging Communication Channel 1.
Clock input pin for programming/debugging Communication
Channel 1.
PGED2
PGEC2
I/O
I
ST
ST
No
No
Data I/O pin for programming/debugging Communication Channel 2.
Clock input pin for programming/debugging Communication
Channel 2.
PGED3
PGEC3
I/O
I
ST
ST
No
No
Data I/O pin for programming/debugging Communication Channel 3.
Clock input pin for programming/debugging Communication
Channel 3.
MCLR
AVDD
I/P
P
ST
P
No
No
Master Clear (Reset) input. This pin is an active-low Reset to the
device.
Positive supply for analog modules. This pin must be connected at
all times. AVDD is connected to VDD.
AVSS
VDD
P
P
P
P
P
No
No
No
No
Ground reference for analog modules. AVSS is connected to VSS.
Positive supply for peripheral logic and I/O pins.
CPU logic filter capacitor connection.
—
—
—
VCAP
VSS
Ground reference for logic and I/O pins.
Legend: CMOS = CMOS compatible input or output
ST = Schmitt Trigger input with CMOS levels
TTL = Transistor-Transistor Logic
Analog = Analog input
P = Power
PPS = Peripheral Pin Select
I = Input
O = Output
DS70000318G-page 20
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
2.2
Decoupling Capacitors
2.0
GUIDELINES FOR GETTING
STARTED WITH 16-BIT
DIGITAL SIGNAL
The use of decoupling capacitors on every pair of
power supply pins, such as VDD, VSS, AVDD and
AVSS is required.
CONTROLLERS
Consider the following criteria when using decoupling
capacitors:
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
• Value and type of capacitor: Recommendation
of 0.1 µF (100 nF), 10-20V. This capacitor should
be a low-ESR and have resonance frequency in
the range of 20 MHz and higher. It is
dsPIC33FJ16GSX02/X04
family
of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to the “dsPIC33F/PIC24H
Family Reference Manual”, which is
available from the Microchip web site
(www.microchip.com).
recommended that ceramic capacitors be used.
• Placement on the printed circuit board: The
decoupling capacitors should be placed as close
to the pins as possible. It is recommended to
place the capacitors on the same side of the
board as the device. If space is constricted, the
capacitor can be placed on another layer on the
PCB using a via; however, ensure that the trace
length from the pin to the capacitor is within
one-quarter inch (6 mm) in length.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
• Handling high frequency noise: If the board is
experiencing high frequency noise, upward of
tens of MHz, add a second ceramic-type capacitor
in parallel to the above described decoupling
capacitor. The value of the second capacitor can
be in the range of 0.01 µF to 0.001 µF. Place this
second capacitor next to the primary decoupling
capacitor. In high-speed circuit designs, consider
implementing a decade pair of capacitances as
close to the power and ground pins as possible.
For example, 0.1 µF in parallel with 0.001 µF.
2.1
Basic Connection Requirements
Getting started with the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 family of 16-bit Digital Signal
Controllers (DSC) requires attention to a minimal set of
device pin connections before proceeding with
development. The following is a list of pin names, which
must always be connected:
• All VDD and VSS pins
(see Section 2.2 “Decoupling Capacitors”)
• Maximizing performance: On the board layout
from the power supply circuit, run the power and
return traces to the decoupling capacitors first,
and then to the device pins. This ensures that the
decoupling capacitors are first in the power chain.
Equally important is to keep the trace length
between the capacitor and the power pins to a
minimum thereby reducing PCB track inductance.
• All AVDD and AVSS pins (regardless if ADC module
is not used)
(see Section 2.2 “Decoupling Capacitors”)
• VCAP
(see Section 2.3 “Capacitor on Internal Voltage
Regulator (VCAP)”)
• MCLR pin
(see Section 2.4 “Master Clear (MCLR) Pin”)
• PGECx/PGEDx pins used for In-Circuit Serial
Programming™ (ICSP™) and debugging purposes
(see Section 2.5 “ICSP™ Pins”)
• OSC1 and OSC2 pins when external oscillator
source is used
(see Section 2.6 “External Oscillator Pins”)
2008-2014 Microchip Technology Inc.
DS70000318G-page 21
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The placement of this capacitor should be close to the
VCAP. It is recommended that the trace length not
exceed one-quarter inch (6 mm). Refer to Section 21.2
“On-Chip Voltage Regulator” for details.
FIGURE 2-1:
RECOMMENDED
MINIMUM CONNECTION
0.1 µF
Ceramic
10 µF
Tantalum
VDD
2.4
Master Clear (MCLR) Pin
R
The MCLR pin provides two specific device
functions:
R1
MCLR
• Device Reset
C
• Device programming and debugging.
dsPIC33F
During device programming and debugging, the
resistance and capacitance that can be added to the
pin must be considered. Device programmers and
debuggers drive the MCLR pin. Consequently,
specific voltage levels (VIH and VIL) and fast signal
transitions must not be adversely affected. Therefore,
specific values of R and C will need to be adjusted
based on the application and PCB requirements.
VDD
VSS
VDD
VSS
0.1 µF
Ceramic
0.1 µF
Ceramic
0.1 µF
Ceramic
0.1 µF
Ceramic
(1)
L1
For example, as shown in Figure 2-2, it is
recommended that the capacitor C, be isolated from
the MCLR pin during programming and debugging
operations.
Note 1: As an option, instead of a hard-wired connection, an
inductor (L1) can be substituted between VDD and
AVDD to improve ADC noise rejection. The inductor
impedance should be less than 1 and the inductor
capacity greater than 10 mA.
Place the components shown in Figure 2-2 within
one-quarter inch (6 mm) from the MCLR pin.
Where:
FCNV
2
f = -------------
(i.e., ADC conversion rate/2)
FIGURE 2-2:
EXAMPLE OF MCLR PIN
CONNECTIONS
1
f = -----------------------
2 LC
VDD
2
1
---------------------
L =
R
2f C
R1
MCLR
2.2.1
TANK CAPACITORS
dsPIC33F
JP
C
On boards with power traces running longer than six
inches in length, it is suggested to use a tank capacitor
for integrated circuits including DSCs to supply a local
power source. The value of the tank capacitor should
be determined based on the trace resistance that con-
nects the power supply source to the device, and the
maximum current drawn by the device in the applica-
tion. In other words, select the tank capacitor so that it
meets the acceptable voltage sag at the device. Typical
values range from 4.7 µF to 47 µF.
Note 1: R 10 k is recommended. A suggested
starting value is 10 k. Ensure that the MCLR
pin VIH and VIL specifications are met.
2: R1 470 will limit any current flowing into
MCLR from the external capacitor, C, in the
event of MCLR pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
VIH and VIL specifications are met.
2.3
Capacitor on Internal Voltage
Regulator (VCAP)
A low-ESR (<5 Ohms) capacitor is required on the
VCAP pin, which is used to stabilize the voltage
regulator output voltage. The VCAP pin must not be
connected to VDD, and must have a capacitor between
4.7 µF and 10 µF, 16V connected to ground. The type
can be ceramic or tantalum. Refer to Section 24.0
“Electrical Characteristics” for additional information.
DS70000318G-page 22
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 2-3:
SUGGESTED PLACEMENT
OF THE OSCILLATOR
CIRCUIT
2.5
ICSP™ Pins
The PGECx and PGEDx pins are used for In-Circuit
Serial Programming™ (ICSP™) and debugging
purposes. It is recommended to keep the trace length
between the ICSP connector and the ICSP pins on the
device as short as possible. If the ICSP connector is
expected to experience an ESD event, a series resistor
is recommended, with the value in the range of a few
tens of Ohms, not to exceed 100 Ohms.
Main Oscillator
Guard Ring
13
14
15
16
17
18
19
20
Guard Trace
Pull-up resistors, series diodes, and capacitors on the
PGECx and PGEDx pins are not recommended as they
will interfere with the programmer/debugger
communications to the device. If such discrete
components are an application requirement, they
should be removed from the circuit during program-
ming and debugging. Alternatively, refer to the AC/DC
characteristics and timing requirements information in
the respective device Flash programming specification
for information on capacitive loading limits and pin input
voltage high (VIH) and input low (VIL) requirements.
Secondary
Oscillator
2.7
Oscillator Value Conditions on
Device Start-up
If the PLL of the target device is enabled and
configured for the device start-up oscillator, the
maximum oscillator source frequency must be limited
to 4 MHz < FIN < 8 MHz to comply with device PLL
start-up conditions. This means that if the external
oscillator frequency is outside this range, the
application must start up in the FRC mode first. The
default PLL settings after a POR with an oscillator
frequency outside this range will violate the device
operating speed.
Ensure that the “Communication Channel Select”
(i.e., PGECx/PGEDx pins) programmed into the device
matches the physical connections for the ICSP to
MPLAB® ICD 3 or MPLAB® REAL ICE™.
For more information on ICD 3 and REAL ICE
connection requirements, refer to the following
documents that are available on the Microchip web site.
• “Using MPLAB® ICD 3” (poster) DS51765
• “MPLAB® ICD 3 Design Advisory” DS51764
• “MPLAB® REAL ICE™ In-Circuit Debugger
User’s Guide” DS51616
• “Using MPLAB® REAL ICE™” (poster) DS51749
Once the device powers up, the application firmware
can initialize the PLL SFRs, CLKDIV, and PLLFBD to a
suitable value, and then perform a clock switch to the
Oscillator + PLL clock source. Note that clock switching
must be enabled in the device Configuration Word.
2.6
External Oscillator Pins
Many DSCs have options for at least two oscillators: a
high-frequency primary oscillator and a low-frequency
secondary oscillator (refer to Section 8.0 “Oscillator
Configuration” for details).
The oscillator circuit should be placed on the same
side of the board as the device. Also, place the
oscillator circuit close to the respective oscillator pins,
not exceeding one-half inch (12 mm) distance
between them. The load capacitors should be placed
next to the oscillator itself, on the same side of the
board. Use a grounded copper pour around the
oscillator circuit to isolate them from surrounding
circuits. The grounded copper pour should be routed
directly to the MCU ground. Do not run any signal
traces or power traces inside the ground pour. Also, if
using a two-sided board, avoid any traces on the
other side of the board where the crystal is placed. A
suggested layout is shown in Figure 2-3.
2008-2014 Microchip Technology Inc.
DS70000318G-page 23
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
2.8
Configuration of Analog and
Digital Pins During ICSP
Operations
2.9
Unused I/Os
Unused I/O pins should be configured as outputs and
driven to a logic-low state.
If MPLAB ICD 2, ICD 3 or REAL ICE is selected as a
debugger, it automatically initializes all of the A/D input
pins (ANx) as “digital” pins, by setting all bits in the
ADPCFG register.
Alternatively, connect a 1k to 10k resistor between VSS
and unused pins and drive the output to logic low.
2.10 Typical Application Connection
Examples
The bits in the registers that correspond to the A/D pins
that are initialized by MPLAB ICD 2, ICD 3, or REAL
ICE, must not be cleared by the user application firm-
ware; otherwise, communication errors will result
between the debugger and the device.
Examples of typical application connections are shown
in Figure 2-4 through Figure 2-11.
If your application needs to use certain A/D pins as
analog input pins during the debug session, the user
application must clear the corresponding bits in the
ADPCFG register during initialization of the ADC module.
When MPLAB ICD 2, ICD 3, or REAL ICE is used as a
programmer, the user application firmware must correctly
configure the ADPCFG register. Automatic initialization
of these registers is only done during debugger opera-
tion. Failure to correctly configure the register(s) will
result in all A/D pins being recognized as analog input
pins, resulting in the port value being read as a logic ‘0’,
which may affect user application functionality.
DS70000318G-page 24
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 2-4:
DIGITAL PFC
IPFC
VHV_BUS
|VAC|
k
1
k
3
VAC
FET
Driver
k
2
ADC Channel
ADC Channel PWM Output
ADC Channel
dsPIC33FJ06GS101
FIGURE 2-5:
BOOST CONVERTER IMPLEMENTATION
IPFC
VINPUT
VOUTPUT
k
1
k
3
FET
Driver
k
2
ADC Channel
ADC
PWM
ADC Channel
Channel
Output
dsPIC33FJ06GS101
2008-2014 Microchip Technology Inc.
DS70000318G-page 25
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 2-6:
SINGLE-PHASE SYNCHRONOUS BUCK CONVERTER
12V Input
5V Output
I
5V
FET
Driver
k
k
k
7
2
1
ADC
Channel
Analog
Comp.
ADC
Channel
dsPIC33FJ06GS202
FIGURE 2-7:
MULTI-PHASE SYNCHRONOUS BUCK CONVERTER
3.3V Output
12V Input
k
6
FET
Driver
FET
Driver
k
7
ADC
Channel
PWM
PWM
FET
Driver
k
k
k
Analog Comparator
3
4
5
dsPIC33FJ06GS502
Analog Comparator
Analog Comparator
ADC Channel
DS70000318G-page 26
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 2-8:
OFF-LINE UPS
VDC
Full-Bridge Inverter
Push-Pull Converter
V
OUT
+
-
VBAT
+
VOUT
GND
GND
FET
Driver
FET
FET
FET
FET
FET
Driver
k
k
k
k
5
2
1
4
Driver Driver Driver Driver
PWM
ADC
PWM ADC ADC
or
PWM PWM
PWM PWM
Analog Comp.
k
ADC
ADC
3
dsPIC33FJ16GS504
PWM
ADC
FET
Driver
k
6
+
Battery Charger
2008-2014 Microchip Technology Inc.
DS70000318G-page 27
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 2-9:
INTERLEAVED PFC
VOUT+
|VAC|
k
VAC
4
k
3
k
k
1
2
VOUT-
FET
Driver
FET
Driver
ADC
Channel
ADC
Channel
ADC Channel
ADC Channel
ADC
Channel
PWM
PWM
dsPIC33FJ06GS202
DS70000318G-page 28
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 2-10:
PHASE-SHIFTED FULL-BRIDGE CONVERTER
VIN+
Gate 6
Gate 3
Gate 1
VOUT+
VOUT-
S1
S3
Gate 2
VIN-
Gate 4
Gate 5
Gate 5
FET
Driver
k
2
k
1
Analog
Ground
Gate 1
S1
FET
Driver
ADC
Channel
PWM
ADC
Channel
PWM
PWM
Gate 3
dsPIC33FJ06GS202
FET
Driver
S3
Gate 2
Gate 4
2008-2014 Microchip Technology Inc.
DS70000318G-page 29
FIGURE 2-11:
AC-TO-DC POWER SUPPLY WITH PFC AND THREE OUTPUTS (12V, 5V AND 3.3V)
ZVT with Current Doubler Synchronous Rectifier
VHV_BUS
Isolation
Barrier
VOUT
IZVT
3.3V Multi-Phase Buck Stage
3.3V Output
12V Input
I3.3V_1
FET
Driver
FET
Driver
FET
Driver
5V Output
I5V
5V Buck Stage
k4
I3.3V_2
ADC
ADC
Channel Channel
FET
FET
Driver Driver
PWM
k11
Primary Controller
dsPIC33FJ16GS504
FET
Driver
I3.3V_3
PWM
k5
k6
k7
UART
RX
ADC
Ch.
ADC
Ch.
ADC
Ch.
PWM
Output
ADC
Channel
Analog
Comp.
ADC
Channel
PWM
PWM
FET
Driver
k8
k9
Analog Comparator
Secondary Controller
dsPIC33FJ16GS504
Analog Comparator
PFC Stage
k2
UART
TX
k10
Analog Comparator
ADC Channel
FET Driver
VAC
k3
k1
|VAC|
VHV_BUS
IPFC
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
3.1
Data Addressing Overview
3.0
CPU
The data space can be addressed as 32K words or
64 Kbytes and is split into two blocks, referred to as X
and Y data memory. Each memory block has its own
independent Address Generation Unit (AGU). The
MCU class of instructions operates solely through the
X memory AGU, which accesses the entire memory
map as one linear data space. Certain DSP instructions
operate through the X and Y AGUs to support dual
operand reads, which splits the data address space
into two parts. The X and Y data space boundary is
device-specific.
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “CPU” (DS70204) in the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
Overhead-free circular buffers (Modulo Addressing
mode) are supported in both X and Y address spaces.
The Modulo Addressing removes the software
boundary checking overhead for DSP algorithms.
Furthermore, the X AGU circular addressing can be
used with any of the MCU class of instructions. The X
AGU also supports Bit-Reversed Addressing to greatly
simplify input or output data reordering for radix-2 FFT
algorithms.
The CPU module has a 16-bit (data) modified Harvard
architecture with an enhanced instruction set, including
significant support for DSP. The CPU has a 24-bit
instruction word with a variable length opcode field.
The Program Counter (PC) is 23 bits wide and
addresses up to 4M x 24 bits of user program memory
space. The actual amount of program memory
implemented varies from device to device. A single-
cycle instruction prefetch mechanism is used to help
maintain throughput and provides predictable
execution. All instructions execute in a single cycle,
with the exception of instructions that change the
program flow, the double-word move (MOV.D)
instruction and the table instructions. Overhead-free
program loop constructs are supported using the DO
and REPEAT instructions, both of which are
interruptible at any point.
The upper 32 Kbytes of the data space memory map
can optionally be mapped into program space at any
16K program word boundary defined by the 8-bit
Program Space Visibility Page (PSVPAG) register. The
program-to-data space mapping feature allows any
instruction access program space as if it were data
space.
3.2
DSP Engine Overview
The DSP engine features a high-speed, 17-bit by 17-bit
multiplier, 40-bit ALU, two 40-bit saturating
a
accumulators and a 40-bit bidirectional barrel shifter.
The barrel shifter is capable of shifting a 40-bit value up
to 16 bits, right or left, in a single cycle. The DSP
instructions operate seamlessly with all other
instructions and have been designed for optimal real-
time performance. The MAC instruction and other
associated instructions can concurrently fetch two data
operands from memory while multiplying two W
registers and accumulating and optionally saturating
the result in the same cycle. This instruction
functionality requires that the RAM data space be split
for these instructions and linear for all others. Data
space partitioning is achieved in a transparent and
flexible manner through dedicating certain Working
registers to each address space.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices have sixteen, 16-bit Working registers in
the programmer’s model. Each of the Working registers
can serve as a data, address or address offset register.
The sixteenth Working register (W15) operates as a
software Stack Pointer (SP) for interrupts and calls.
There are two classes of instruction in the
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices: MCU and DSP. These two instruction
classes are seamlessly integrated into a single CPU.
The instruction set includes many addressing modes
and is designed for optimum C compiler efficiency. For
most instructions, the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 is capable of executing a
data (or program data) memory read, a Working
register (data) read, a data memory write and a
program (instruction) memory read per instruction
cycle. As a result, three parameter instructions can be
supported, allowing A + B = C operations to be
executed in a single cycle.
A block diagram of the CPU is shown in Figure 3-1,
and the programmer’s model is shown in Figure 3-2.
2008-2014 Microchip Technology Inc.
DS70000318G-page 31
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
3.3
Special MCU Features
X04 devices support 16/16 and 32/16 divide operations,
both fractional and integer. All divide instructions are iter-
ative operations. They must be executed within a REPEAT
loop, resulting in a total execution time of 19 instruction
cycles. The divide operation can be interrupted during any
of those 19 cycles without loss of data.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
devices feature a 17-bit by 17-bit single-cycle multi-
plier that is shared by both the MCU ALU and DSP
engine. The multiplier can perform signed, unsigned
and mixed sign multiplication. Using a 17-bit by 17-bit
multiplier for 16-bit by 16-bit multiplication not only
allows you to perform mixed sign multiplication, it
also achieves accurate results for special operations,
such as (-1.0) x (1.0).
A 40-bit barrel shifter is used to perform up to a 16-bit
left or right shift in a single cycle. The barrel shifter can
be used by both MCU and DSP instructions.
FIGURE 3-1:
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 CPU CORE
BLOCK DIAGRAM
PSV & Table
Data Access
Control Block
Y Data Bus
X Data Bus
Interrupt
Controller
16
Data Latch
16
16
8
16
Data Latch
Y RAM
23
16
PCU PCH PCL
Program Counter
X RAM
23
Address
Latch
Address
Latch
Stack
Control
Logic
Loop
Control
Logic
23
16
16
Address Generator Units
Address Latch
Program Memory
Data Latch
EA MUX
ROM Latch
24
16
16
Instruction
Decode &
Control
Instruction Reg
16
Control Signals
to Various Blocks
DSP Engine
16 x 16
W Register Array
Divide Support
16
16-Bit ALU
16
To Peripheral Modules
DS70000318G-page 32
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 3-2:
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 PROGRAMMER’S MODEL
D15
D0
W0/WREG
W1
PUSH.SShadow
DOShadow
W2
W3
Legend
W4
DSP Operand
Registers
W5
W6
W7
Working Registers
W8
W9
DSP Address
Registers
W10
W11
W12/DSP Offset
W13/DSP Write Back
W14/Frame Pointer
W15/Stack Pointer
SPLIM
Stack Pointer Limit Register
AD15
AD39
ACCA
AD31
AD0
DSP
Accumulators
ACCB
PC22
PC0
0
Program Counter
0
7
TBLPAG
Data Table Page Address
7
0
PSVPAG
Program Space Visibility Page Address
15
0
0
RCOUNT
REPEATLoop Counter
DOLoop Counter
15
DCOUNT
22
0
DOSTART
DOEND
DOLoop Start Address
DOLoop End Address
22
15
0
Core Configuration Register
CORCON
OA OB SA SB OAB SAB DA DC
SRH
RA
N
Z
C
IPL2 IPL1 IPL0
OV
STATUS Register
SRL
2008-2014 Microchip Technology Inc.
DS70000318G-page 33
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
3.4
CPU Control Registers
REGISTER 3-1:
SR: CPU STATUS REGISTER
R-0
OA
R-0
OB
R/C-0
SA(1)
R/C-0
SB(1)
R-0
R/C-0
SAB(1,4)
R-0
DA
R/W-0
DC
OAB
bit 15
bit 8
R/W-0(3)
IPL2(2)
bit 7
R/W-0(3)
IPL1(2)
R/W-0(3)
IPL0(2)
R-0
RA
R/W-0
N
R/W-0
OV
R/W-0
Z
R/W-0
C
bit 0
Legend:
C = Clearable bit
W = Writable bit
R = Readable bit
0’ = Bit is cleared
-n = Value at POR
‘1’ = Bit is set
‘x = Bit is unknown
U = Unimplemented bit, read as ‘0’
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
OA: Accumulator A Overflow Status bit
1= Accumulator A has overflowed
0= Accumulator A has not overflowed
OB: Accumulator B Overflow Status bit
1= Accumulator B has overflowed
0= Accumulator B has not overflowed
SA: Accumulator A Saturation ‘Sticky’ Status bit(1)
1= Accumulator A is saturated or has been saturated at some time
0= Accumulator A is not saturated
SB: Accumulator B Saturation ‘Sticky’ Status bit(1)
1= Accumulator B is saturated or has been saturated at some time
0= Accumulator B is not saturated
OAB: OA || OB Combined Accumulator Overflow Status bit
1= Accumulator A or B has overflowed
0= Neither Accumulator A or B has overflowed
SAB: SA || SB Combined Accumulator ‘Sticky’ Status bit(1,4)
1= Accumulator A or B is saturated or has been saturated at some time in the past
0= Neither Accumulator A or B is saturated
DA: DOLoop Active bit
1= DOloop in progress
0= DOloop not in progress
bit 8
DC: MCU ALU Half Carry/Borrow bit
1= A carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data)
of the result occurred
0= No carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized
data) of the result occurred
Note 1: This bit can be read or cleared (not set).
2: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority
Level (IPL). The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when
IPL<3> = 1.
3: The IPL<2:0> Status bits are read-only when NSTDIS = 1(INTCON1<15>).
4: Clearing this bit will clear SA and SB.
DS70000318G-page 34
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 3-1:
SR: CPU STATUS REGISTER (CONTINUED)
bit 7-5
IPL<2:0>: CPU Interrupt Priority Level Status bits(2,3)
111= CPU Interrupt Priority Level is 7 (15), user interrupts disabled
110= CPU Interrupt Priority Level is 6 (14)
101= CPU Interrupt Priority Level is 5 (13)
100= CPU Interrupt Priority Level is 4 (12)
011= CPU Interrupt Priority Level is 3 (11)
010= CPU Interrupt Priority Level is 2 (10)
001= CPU Interrupt Priority Level is 1 (9)
000= CPU Interrupt Priority Level is 0 (8)
bit 4
bit 3
bit 2
RA: REPEATLoop Active bit
1= REPEATloop in progress
0= REPEATloop not in progress
N: MCU ALU Negative bit
1= Result was negative
0= Result was non-negative (zero or positive)
OV: MCU ALU Overflow bit
This bit is used for signed arithmetic (2’s complement). It indicates an overflow of a magnitude that
causes the sign bit to change state.
1= Overflow occurred for signed arithmetic (in this arithmetic operation)
0= No overflow occurred
bit 1
bit 0
Z: MCU ALU Zero bit
1= An operation that affects the Z bit has set it at some time in the past
0= The most recent operation that affects the Z bit has cleared it (i.e., a non-zero result)
C: MCU ALU Carry/Borrow bit
1= A carry-out from the Most Significant bit (MSb) of the result occurred
0= No carry-out from the Most Significant bit of the result occurred
Note 1: This bit can be read or cleared (not set).
2: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority
Level (IPL). The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when
IPL<3> = 1.
3: The IPL<2:0> Status bits are read-only when NSTDIS = 1(INTCON1<15>).
4: Clearing this bit will clear SA and SB.
2008-2014 Microchip Technology Inc.
DS70000318G-page 35
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 3-2:
CORCON: CORE CONTROL REGISTER
U-0
—
U-0
—
U-0
—
R/W-0
US
R/W-0
EDT(1)
R-0
R-0
R-0
DL2
DL1
DL0
bit 15
bit 8
R/W-0
SATA
R/W-0
SATB
R/W-1
R/W-0
R/C-0
IPL3(2)
R/W-0
PSV
R/W-0
RND
R/W-0
IF
SATDW
ACCSAT
bit 7
bit 0
Legend:
C = Clearable bit
W = Writable bit
‘x = Bit is unknown
R = Readable bit
0’ = Bit is cleared
-n = Value at POR
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
bit 15-13
bit 12
Unimplemented: Read as ‘0’
US: DSP Multiply Unsigned/Signed Control bit
1= DSP engine multiplies are unsigned
0= DSP engine multiplies are signed
bit 11
EDT: Early DOLoop Termination Control bit(1)
1= Terminate executing DOloop at end of current loop iteration
0= No effect
bit 10-8
DL<2:0>: DOLoop Nesting Level Status bits
111= 7 DOloops are active
•
•
•
001= 1 DOloop is active
000= 0 DOloops are active
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
SATA: ACCA Saturation Enable bit
1= Accumulator A saturation is enabled
0= Accumulator A saturation is disabled
SATB: ACCB Saturation Enable bit
1= Accumulator B saturation is enabled
0= Accumulator B saturation is disabled
SATDW: Data Space Write from DSP Engine Saturation Enable bit
1= Data space write saturation is enabled
0= Data space write saturation is disabled
ACCSAT: Accumulator Saturation Mode Select bit
1= 9.31 saturation (super saturation)
0= 1.31 saturation (normal saturation)
IPL3: CPU Interrupt Priority Level Status bit 3(2)
1= CPU Interrupt Priority Level is greater than 7
0= CPU Interrupt Priority Level is 7 or less
PSV: Program Space Visibility in Data Space Enable bit
1= Program space is visible in data space
0= Program space is not visible in data space
Note 1: This bit will always read as ‘0’.
2: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level.
DS70000318G-page 36
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 3-2:
CORCON: CORE CONTROL REGISTER (CONTINUED)
bit 1
bit 0
RND: Rounding Mode Select bit
1= Biased (conventional) rounding is enabled
0= Unbiased (convergent) rounding is enabled
IF: Integer or Fractional Multiplier Mode Select bit
1= Integer mode is enabled for DSP multiply ops
0= Fractional mode is enabled for DSP multiply ops
Note 1: This bit will always read as ‘0’.
2: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level.
2008-2014 Microchip Technology Inc.
DS70000318G-page 37
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
3.5
Arithmetic Logic Unit (ALU)
3.6
DSP Engine
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 ALU is 16 bits wide and is capable of addition,
subtraction, bit shifts and logic operations. Unless
otherwise mentioned, arithmetic operations are 2’s com-
plement in nature. Depending on the operation, the ALU
can affect the values of the Carry (C), Zero (Z),
Negative (N), Overflow (OV) and Digit Carry (DC) Status
bits in the SR register. The C and DC Status bits operate
as Borrow and Digit Borrow bits, respectively, for
subtraction operations.
The DSP engine consists of a high-speed, 17-bit x 17-bit
multiplier, a barrel shifter and a 40-bit adder/subtracter
(with two target accumulators, round and saturation
logic).
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 is a single-cycle instruction flow architecture;
therefore, concurrent operation of the DSP engine with
MCU instruction flow is not possible. However, some
MCU ALU and DSP engine resources can be used
concurrently by the same instruction (for example, ED,
EDAC).
The ALU can perform 8-bit or 16-bit operations,
depending on the mode of the instruction that is used.
Data for the ALU operation can come from the W
register array or data memory, depending on the
addressing mode of the instruction. Likewise, output
data from the ALU can be written to the W register array
or a data memory location.
The DSP engine can also perform inherent
accumulator-to-accumulator operations that require no
additional data. These instructions are ADD, SUB and
NEG.
The DSP engine has options selected through bits in
the CPU Core Control register (CORCON), as listed
below:
Refer to the “16-bit MCU and DSC Programmer’s
Reference Manual” (DS70157) for information on the
SR bits affected by each instruction.
• Fractional or Integer DSP Multiply (IF)
• Signed or Unsigned DSP Multiply (US)
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 CPU incorporates hardware support for both multipli-
cation and division. This includes a dedicated hardware
multiplier and support hardware for 16-bit-divisor division.
• Conventional or Convergent Rounding (RND)
• Automatic Saturation On/Off for ACCA (SATA)
• Automatic Saturation On/Off for ACCB (SATB)
• Automatic Saturation On/Off for Writes to Data
Memory (SATDW)
3.5.1
MULTIPLIER
Using the high-speed, 17-bit x 17-bit multiplier of the
DSP engine, the ALU supports unsigned, signed or
mixed sign operation in several MCU multiplication
modes:
• Accumulator Saturation mode Selection
(ACCSAT)
A block diagram of the DSP engine is shown in
Figure 3-3.
• 16-bit x 16-bit signed
• 16-bit x 16-bit unsigned
TABLE 3-1:
Instruction
DSP INSTRUCTIONS
SUMMARY
• 16-bit signed x 5-bit (literal) unsigned
• 16-bit unsigned x 16-bit unsigned
• 16-bit unsigned x 5-bit (literal) unsigned
• 16-bit unsigned x 16-bit signed
• 8-bit unsigned x 8-bit unsigned
Algebraic
ACC
Operation
Write Back
CLR
A = 0
Yes
No
ED
A = (x – y)2
A = A + (x – y)2
A = A + (x * y)
A = A + x2
3.5.2
DIVIDER
EDAC
MAC
No
The divide block supports 32-bit/16-bit and 16-bit/16-bit
signed and unsigned integer divide operations with the
following data sizes:
Yes
No
MAC
MOVSAC
MPY
No change in A
A = x * y
A = x 2
Yes
No
• 32-bit signed/16-bit signed divide
• 32-bit unsigned/16-bit unsigned divide
• 16-bit signed/16-bit signed divide
• 16-bit unsigned/16-bit unsigned divide
MPY
No
MPY.N
MSC
A = – x * y
No
A = A – x * y
Yes
The quotient for all divide instructions ends up in W0 and
the remainder in W1. The 16-bit signed and unsigned
DIVinstructions can specify any W register for both the
16-bit divisor (Wn) and any W register (aligned) pair
(W(m + 1):Wm) for the 32-bit dividend. The divide
algorithm takes one cycle per bit of divisor, so both 32-bit/
16-bit and 16-bit/16-bit instructions take the same
number of cycles to execute.
DS70000318G-page 38
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 3-3:
DSP ENGINE BLOCK DIAGRAM
S
a
40
40-Bit Accumulator A
40-Bit Accumulator B
16
40
t
u
r
Round
Logic
a
t
Carry/Borrow Out
Carry/Borrow In
Saturate
Adder
e
Negate
40
40
40
Barrel
Shifter
16
40
Sign-Extend
32
16
Zero Backfill
32
33
17-Bit
Multiplier/Scaler
16
16
To/From W Array
2008-2014 Microchip Technology Inc.
DS70000318G-page 39
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
3.6.1
MULTIPLIER
3.6.2.1
Adder/Subtracter, Overflow and
Saturation
The 17-bit x 17-bit multiplier is capable of signed or
unsigned operation and can multiplex its output using a
scaler to support either 1.31 fractional (Q31) or 32-bit
integer results. Unsigned operands are zero-extended
into the 17th bit of the multiplier input value. Signed
operands are sign-extended into the 17th bit of the
multiplier input value. The output of the 17-bit x 17-bit
multiplier/scaler is a 33-bit value that is sign-extended
to 40 bits. Integer data is inherently represented as a
signed 2’s complement value, where the Most
Significant bit (MSb) is defined as a sign bit. The range
of an N-bit 2’s complement integer is -2N-1 to 2N-1 – 1.
The adder/subtracter is a 40-bit adder with an optional
zero input into one side, and either true or complement
data into the other input.
• In the case of addition, the Carry/Borrow input is
active-high and the other input is true data (not
complemented).
• In the case of subtraction, the Carry/Borrow input
is active-low and the other input is complemented.
The adder/subtracter generates Overflow Status bits,
SA/SB and OA/OB, which are latched and reflected in
the STATUS Register:
• For a 16-bit integer, the data range is -32768
(0x8000) to 32767 (0x7FFF), including 0.
• Overflow from bit 39: this is a catastrophic
overflow in which the sign of the accumulator is
destroyed.
• For a 32-bit integer, the data range is
-2,147,483,648 (0x8000 0000) to 2,147,483,647
(0x7FFF FFFF).
• Overflow into guard bits, 32 through 39: this is a
recoverable overflow. This bit is set whenever all
the guard bits are not identical to each other.
When the multiplier is configured for fractional
multiplication, the data is represented as a 2’s
complement fraction, where the MSb is defined as a
sign bit and the radix point is implied to lie just after the
sign bit (QX format). The range of an N-bit
2’s complement fraction with this implied radix point is
-1.0 to (1 – 21-N). For a 16-bit fraction, the Q15 data
range is -1.0 (0x8000) to 0.999969482 (0x7FFF)
including 0 and has a precision of 3.01518x10-5. In
Fractional mode, the 16 x 16 multiply operation
generates a 1.31 product that has a precision of
The adder has an additional saturation block that
controls accumulator data saturation, if selected. It
uses the result of the adder, the Overflow Status bits
described
previously
and
the
SAT<A:B>
(CORCON<7:6>) and ACCSAT (CORCON<4>) mode
control bits to determine when and to what value to
saturate.
Six STATUS Register bits support saturation and
overflow:
4.65661 x 10-10
.
• OA: ACCA overflowed into guard bits
• OB: ACCB overflowed into guard bits
The same multiplier is used to support the MCU
multiply instructions, which include integer 16-bit
signed, unsigned and mixed sign multiply operations.
• SA: ACCA saturated (bit 31 overflow and
saturation)
or
ACCA overflowed into guard bits and saturated
(bit 39 overflow and saturation)
The MUL instruction can be directed to use byte or
word-sized operands. Byte operands will direct a 16-bit
result, and word operands will direct a 32-bit result to
the specified register(s) in the W array.
• SB: ACCB saturated (bit 31 overflow and
saturation)
or
3.6.2
DATA ACCUMULATORS AND
ADDER/SUBTRACTER
ACCB overflowed into guard bits and saturated
(bit 39 overflow and saturation)
The data accumulator consists of a 40-bit adder/
subtracter with automatic sign extension logic. It can
select one of two accumulators (A or B) as its pre-
• OAB: Logical OR of OA and OB
• SAB: Logical OR of SA and SB
accumulation
source
and
post-accumulation
The OA and OB bits are modified each time data
passes through the adder/subtracter. When set, they
indicate that the most recent operation has overflowed
into the accumulator guard bits (bits 32 through 39).
The OA and OB bits can also optionally generate an
arithmetic warning trap when set and the correspond-
ing Overflow Trap Flag Enable bits (OVATE, OVBTE) in
the INTCON1 register are set (refer to Section 7.0
“Interrupt Controller”). This allows the user applica-
tion to take immediate action, for example, to correct
system gain.
destination. For the ADDand LACinstructions, the data
to be accumulated or loaded can be optionally scaled
using the barrel shifter prior to accumulation.
DS70000318G-page 40
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The SA and SB bits are modified each time data
passes through the adder/subtracter, but can only be
cleared by the user application. When set, they indicate
that the accumulator has overflowed its maximum
range (bit 31 for 32-bit saturation or bit 39 for 40-bit
saturation) and will be saturated (if saturation is
enabled). When saturation is not enabled, SA and SB
default to bit 39 overflow and thus, indicate that a cata-
strophic overflow has occurred. If the COVTE bit in the
INTCON1 register is set, SA and SB bits will generate
an arithmetic warning trap when saturation is disabled.
3.6.3
ACCUMULATOR ‘WRITE BACK’
The MAC class of instructions (with the exception of
MPY, MPY.N, ED and EDAC) can optionally write a
rounded version of the high word (bits 31 through 16)
of the accumulator that is not targeted by the instruction
into data space memory. The write is performed across
the X bus into combined X and Y address space. The
following addressing modes are supported:
• W13, Register Direct:
The rounded contents of the non-target accumulator
are written into W13 as a 1.15 fraction.
The Overflow and Saturation Status bits can optionally
be viewed in the STATUS Register (SR) as the logical
OR of OA and OB (in bit OAB) and the logical OR of SA
and SB (in bit SAB). Programmers can check one bit
in the STATUS Register to determine if either
accumulator has overflowed, or one bit to determine if
either accumulator has saturated. This is useful for
complex number arithmetic, which typically uses both
accumulators.
• [W13] + = 2, Register Indirect with Post-Increment:
The rounded contents of the non-target
accumulator are written into the address pointed
to by W13 as a 1.15 fraction. W13 is then
incremented by 2 (for a word write).
3.6.3.1
Round Logic
The round logic is a combinational block that performs
a conventional (biased) or convergent (unbiased)
round function during an accumulator write (store). The
Round mode is determined by the state of the RND bit
in the CORCON register. It generates a 16-bit,
1.15 data value that is passed to the data space write
saturation logic. If rounding is not indicated by the
instruction, a truncated 1.15 data value is stored and
the least significant word is simply discarded.
The device supports three Saturation and Overflow
modes:
• Bit 39 Overflow and Saturation:
When bit 39 overflow and saturation occurs, the
saturation logic loads the maximally positive
9.31 (0x7FFFFFFFFF) or maximally negative
9.31 value (0x8000000000) into the target accumu-
lator. The SA or SB bit is set and remains set until
cleared by the user application. This condition is
referred to as ‘super saturation’ and provides
protection against erroneous data or unexpected
algorithm problems (such as gain calculations).
Conventional rounding zero-extends bit 15 of the accu-
mulator and adds it to the ACCxH word (bits 16 through
31 of the accumulator).
• If the ACCxL word (bits 0 through 15 of the
accumulator) is between 0x8000 and 0xFFFF
(0x8000 included), ACCxH is incremented.
• Bit 31 Overflow and Saturation:
When bit 31 overflow and saturation occurs, the
saturation logic then loads the maximally positive
1.31 value (0x007FFFFFFF) or maximally nega-
tive 1.31 value (0x0080000000) into the target
accumulator. The SA or SB bit is set and remains
set until cleared by the user application. When
this Saturation mode is in effect, the guard bits are
not used, so the OA, OB or OAB bits are never
set.
• If ACCxL is between 0x0000 and 0x7FFF, ACCxH
is left unchanged.
A consequence of this algorithm is that over a
succession of random rounding operations, the value
tends to be biased slightly positive.
Convergent (or unbiased) rounding operates in the same
manner as conventional rounding, except when ACCxL
equals 0x8000. In this case, the Least Significant bit
(bit 16 of the accumulator) of ACCxH is examined:
• Bit 39 Catastrophic Overflow:
The bit 39 Overflow Status bit from the adder is
used to set the SA or SB bit, which remains set
until cleared by the user application. No saturation
operation is performed, and the accumulator is
allowed to overflow, destroying its sign. If the
COVTE bit in the INTCON1 register is set, a
catastrophic overflow can initiate a trap exception.
• If it is ‘1’, ACCxH is incremented.
• If it is ‘0’, ACCxH is not modified.
Assuming that bit 16 is effectively random in nature,
this scheme removes any rounding bias that may
accumulate.
2008-2014 Microchip Technology Inc.
DS70000318G-page 41
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The SAC and SAC.R instructions store either a
truncated (SAC), or rounded (SAC.R) version of the
contents of the target accumulator to data memory via
3.6.4
BARREL SHIFTER
The barrel shifter can perform up to 16-bit arithmetic or
logic right shifts, or up to 16-bit left shifts in a single
cycle. The source can be either of the two DSP
accumulators or the X bus (to support multi-bit shifts of
register or memory data).
the
X
bus, subject to data saturation (see
Section 3.6.3.2 “Data Space Write Saturation”). For
the MAC class of instructions, the accumulator write-
back operation functions in the same manner,
addressing combined MCU (X and Y) data space
though the X bus. For this class of instructions, the data
is always subject to rounding.
The shifter requires a signed binary value to determine
both the magnitude (number of bits) and direction of the
shift operation. A positive value shifts the operand right.
A negative value shifts the operand left. A value of ‘0’
does not modify the operand.
3.6.3.2
Data Space Write Saturation
The barrel shifter is 40 bits wide, thereby obtaining a
40-bit result for DSP shift operations and a 16-bit result
for MCU shift operations. Data from the X bus is
presented to the barrel shifter between bit positions 16
and 31 for right shifts, and between bit positions 0 and
16 for left shifts.
In addition to adder/subtracter saturation, writes to data
space can also be saturated, but without affecting the
contents of the source accumulator. The data space write
saturation logic block accepts a 16-bit, 1.15 fractional
value from the round logic block as its input, together with
overflow status from the original source (accumulator)
and the 16-bit round adder. These inputs are combined
and used to select the appropriate 1.15 fractional value
as output to write to data space memory.
If the SATDW bit in the CORCON register is set, data
(after rounding or truncation) is tested for overflow and
adjusted accordingly:
• For input data greater than 0x007FFF, data
written to memory is forced to the maximum
positive 1.15 value, 0x7FFF.
• For input data less than 0xFF8000, data written to
memory is forced to the maximum negative
1.15 value, 0x8000.
The Most Significant bit of the source (bit 39) is used to
determine the sign of the operand being tested.
If the SATDW bit in the CORCON register is not set, the
input data is always passed through unmodified under
all conditions.
DS70000318G-page 42
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
4.1
Program Address Space
4.0
MEMORY ORGANIZATION
The program address memory space of the
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
devices is 4M instructions. The space is addressable by a
24-bit value derived either from the 23-bit Program
Counter (PC) during program execution, or from table
operation or data space remapping, as described in
Section 4.6 “Interfacing Program and Data Memory
Spaces”.
Note:
This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a compre-
hensive reference source. To complement
the information in this data sheet, refer to
“Program Memory” (DS70202) in the
“dsPIC33F/PIC24H Family Reference Man-
ual”, which is available from the Microchip
web site (www.microchip.com).
User application access to the program memory space
is restricted to the lower half of the address range
(0x000000 to 0x7FFFFF). The exception is the use of
TBLRD/TBLWT operations, which use TBLPAG<7> to
permit access to the Configuration bits and Device ID
sections of the configuration memory space.
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 architecture features separate program and data
memory spaces and buses. This architecture also allows
the direct access to program memory from the data
space during code execution.
The memory maps for the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 devices are shown in Figure 4-1.
FIGURE 4-1:
PROGRAM MEMORY MAPS FOR dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 DEVICES
dsPIC33FJ06GS101/102/202
dsPIC33FJ16GS402/404/502/504
0x000000
0x000002
0x000004
0x000000
GOTOInstruction
Reset Address
GOTOInstruction
Reset Address
0x000002
0x000004
Interrupt Vector Table
Reserved
Interrupt Vector Table
0x0000FE
0x0000FE
0x000100
0x000104
0x0001FE
0x000200
0x000100
Reserved
0x000104
0x0001FE
0x000200
Alternate Vector Table
Alternate Vector Table
User Program
Flash Memory
User Program
Flash Memory
(1792 instructions)
(5376 instructions)
0x000FFE
0x001000
0x002BFE
0x002C00
Unimplemented
Unimplemented
(Read ‘0’s)
(Read ‘0’s)
0x7FFFFE
0x800000
0x7FFFFE
0x800000
Reserved
Reserved
0xF7FFFE
0xF80000
0xF80017
0xF80018
0xF7FFFE
0xF80000
0xF80017
0xF80018
Device Configuration
Registers
Device Configuration
Registers
Reserved
Reserved
0xFEFFFE
0xFEFFFE
DEVID (2)
Reserved
DEVID (2)
Reserved
0xFF0000
0xFF0002
0xFFFFFE
0xFF0000
0xFF0002
0xFFFFFE
2008-2014 Microchip Technology Inc.
DS70000318G-page 43
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
4.1.1
PROGRAM MEMORY
ORGANIZATION
4.1.2
INTERRUPT AND TRAP VECTORS
All dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices reserve the addresses between 0x00000
and 0x000200 for hard-coded program execution vectors.
A hardware Reset vector is provided to redirect code
execution from the default value of the PC on device
Reset to the actual start of code. A GOTO instruction is
programmed by the user application at 0x000000, with
the actual address for the start of code at 0x000002.
The program memory space is organized in word-
addressable blocks. Although it is treated as 24 bits
wide, it is more appropriate consider each address of
the program memory as a lower and upper word, with
the upper byte of the upper word being unimplemented.
The lower word always has an even address, while the
upper word has an odd address (see Figure 4-2).
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices also have two interrupt vector tables, located
from 0x000004 to 0x0000FF and 0x000100 to 0x0001FF.
These vector tables allow each of the device interrupt
sources to be handled by separate Interrupt Service
Routines (ISRs). A more detailed discussion of the
interrupt vector tables is provided in Section 7.1
“Interrupt Vector Table”.
Program memory addresses are always word-aligned
on the lower word, and addresses are incremented or
decremented by two during the code execution. This
arrangement provides compatibility with data memory
space addressing and makes data in the program
memory space accessible.
FIGURE 4-2:
PROGRAM MEMORY ORGANIZATION
least significant word
PC Address
most significant word
23
msw
Address
(lsw Address)
16
8
0
0x000001
0x000003
0x000005
0x000007
0x000000
0x000002
0x000004
0x000006
00000000
00000000
00000000
00000000
Program Memory
‘Phantom’ Byte
(read as ‘0’)
Instruction Width
DS70000318G-page 44
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
All word accesses must be aligned to an even address.
4.2
Data Address Space
Misaligned word data fetches are not supported, so
care must be taken when mixing byte and word
operations, or translating from 8-bit MCU code. If a
misaligned read or write is attempted, an address error
trap is generated. If the error occurred on a read, the
instruction underway is completed. If the error occurred
on a write, the instruction is executed but the write does
not occur. In either case, a trap is then executed,
allowing the system and/or user application to examine
the machine state prior to execution of the address
Fault.
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 CPU has a separate, 16-bit-wide data memory
space. The data space is accessed using separate
Address Generation Units (AGUs) for read and write
operations. The data memory maps is shown in
Figure 4-3.
All Effective Addresses (EAs) in the data memory space
are 16 bits wide and point to bytes within the data space.
This arrangement gives a data space address range of
64 Kbytes or 32K words. The lower half of the data
memory space (that is, when EA<15> = 0) is used for
implemented memory addresses, while the upper half
(EA<15> = 1) is reserved for the Program Space
Visibility area (see Section 4.6.3 “Reading Data from
Program Memory Using Program Space Visibility”).
All byte loads into any W register are loaded into the
Least Significant Byte. The Most Significant Byte is not
modified.
A sign-extend (SE) instruction is provided to allow user
applications to translate 8-bit signed data to 16-bit
signed values. Alternatively, for 16-bit unsigned data,
user applications can clear the MSB of any W register
by executing a zero-extend (ZE) instruction on the
appropriate address.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices implement up to 2 Kbytes of data memory.
Should an EA point to a location outside of this area, an
all zero word or byte will be returned.
4.2.1
DATA SPACE WIDTH
4.2.3
SFR SPACE
The data memory space is organized in byte
addressable, 16-bit wide blocks. Data is aligned in data
memory and registers as 16-bit words, but all data
space EAs resolve to bytes. The Least Significant
Bytes (LSBs) of each word have even addresses, while
the Most Significant Bytes (MSBs) have odd
addresses.
The first 2 Kbytes of the Near Data Space, from 0x0000
to 0x07FF, is primarily occupied by Special Function
Registers (SFRs). These are used by the
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 core and peripheral modules for controlling the
operation of the device.
SFRs are distributed among the modules that they
control, and are generally grouped together by module.
Much of the SFR space contains unused addresses;
these are read as ‘0’.
4.2.2
DATA MEMORY ORGANIZATION
AND ALIGNMENT
To maintain backward compatibility with PIC® MCU
devices and improve data space memory usage
Note:
The actual set of peripheral features and
interrupts varies by the device. Refer to
the corresponding device tables and
pinout diagrams for device-specific
information.
efficiency,
the
dsPIC33FJ06GS101/X02
and
dsPIC33FJ16GSX02/X04 instruction set supports both
word and byte operations. As a consequence of byte
accessibility, all Effective Address calculations are
internally scaled to step through word-aligned memory.
For example, the core recognizes that Post-Modified
Register Indirect Addressing mode [Ws++] that results
in a value of Ws + 1 for byte operations and Ws + 2 for
word operations.
4.2.4
NEAR DATA SPACE
The 8-Kbyte area, between 0x0000 and 0x1FFF, is
referred to as the Near Data Space. Locations in this
space are directly addressable via a 13-bit absolute
address field within all memory direct instructions.
Additionally, the whole data space is addressable using
MOV instructions, which support Memory Direct
Addressing mode with a 16-bit address field or by using
Indirect Addressing mode using a Working register as
an Address Pointer.
Data byte reads will read the complete word that
contains the byte, using the LSB of any EA to
determine which byte to select. The selected byte is
placed onto the LSB of the data path. That is, data
memory and registers are organized as two parallel
byte-wide entities with shared (word) address decode
but separate write lines. Data byte writes only write to
the corresponding side of the array or register that
matches the byte address.
2008-2014 Microchip Technology Inc.
DS70000318G-page 45
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 4-3:
DATA MEMORY MAP FOR dsPIC33FJ06GS101/102 DEVICES WITH 256 BYTES
OF RAM
MSB
Address
LSB
Address
16 Bits
MSb
LSb
0x0000
0x0001
2-Kbyte
SFR Space
SFR Space
0x07FE
0x0800
0x07FF
0x0801
X Data RAM (X)
Y Data RAM (Y)
8-Kbyte
Near Data
Space
0x087F
0x0881
0x087E
0x0880
256 Bytes
SRAM Space
0x08FF
0x0901
0x08FE
0x0900
0x1FFE
0x2000
0x1FFF
0x2001
0x8001
0x8000
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory
0xFFFF
0xFFFE
DS70000318G-page 46
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 4-4:
DATA MEMORY MAP FOR dsPIC33FJ06GS202 DEVICE WITH 1-KBYTE RAM
MSB
Address
LSB
Address
16 Bits
MSb
LSb
0x0000
0x0001
2-Kbyte
SFR Space
SFR Space
0x07FE
0x0800
0x07FF
0x0801
X Data RAM (X)
Y Data RAM (Y)
8-Kbyte
Near Data
Space
0x09FF
0x0A01
0x09FE
0x0A00
1-Kbyte
SRAM Space
0x0BFF
0x0C01
0x0BFE
0x0C00
0x1FFE
0x2000
0x1FFF
0x2001
0x8001
0x8000
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory
0xFFFF
0xFFFE
2008-2014 Microchip Technology Inc.
DS70000318G-page 47
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 4-5:
DATA MEMORY MAP FOR dsPIC33FJ16GS402/404/502/504 DEVICES WITH
2-KBYTE RAM
MSB
Address
LSB
Address
16 Bits
MSb
LSb
0x0000
0x0001
2-Kbyte
SFR Space
SFR Space
0x07FE
0x0800
0x07FF
0x0801
X Data RAM (X)
Y Data RAM (Y)
8-Kbyte
Near Data
Space
0x0BFF
0x0C01
0x0BFE
0x0C00
2-Kbyte
SRAM Space
0x0FFF
0x1001
0x0FFE
0x1000
0x1FFE
0x2000
0x1FFF
0x2001
0x8001
0x8000
X Data
Unimplemented (X)
Optionally
Mapped
into Program
Memory
0xFFFF
0xFFFE
DS70000318G-page 48
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The Y data space is used in concert with the X data
space by the MAC class of instructions (CLR, ED,
EDAC, MAC, MOVSAC, MPY, MPY.Nand MSC) to provide
two concurrent data read paths.
4.2.5
X AND Y DATA SPACES
The core has two data spaces, X and Y. These data
spaces can be considered either separate (for some
DSP instructions), or as one unified linear address
range (for MCU instructions). The data spaces are
accessed using two Address Generation Units (AGUs)
and separate data paths. This feature allows certain
instructions to concurrently fetch two words from RAM,
thereby enabling efficient execution of DSP algorithms,
such as Finite Impulse Response (FIR) filtering and
Fast Fourier Transform (FFT).
Both the X and Y data spaces support Modulo
Addressing mode for all instructions, subject to
addressing mode restrictions. Bit-Reversed Addressing
mode is only supported for writes to X data space.
All data memory writes, including in DSP instructions,
view data space as combined X and Y address space.
The boundary between the X and Y data spaces is
device-dependent and is not user-programmable.
The X data space is used by all instructions and
supports all addressing modes. X data space has
separate read and write data buses. The X read data
bus is the read data path for all instructions that view
data space as combined X and Y address space. It is
also the X data prefetch path for the dual operand DSP
instructions (MACclass).
All Effective Addresses are 16 bits wide and point to
bytes within the data space. Therefore, the data space
address range is 64 Kbytes, or 32K words, though the
implemented memory locations vary by device.
2008-2014 Microchip Technology Inc.
DS70000318G-page 49
TABLE 4-1:
CPU CORE REGISTER MAP
SFR
Addr
All
Resets
File Name
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WREG0
WREG1
WREG2
WREG3
WREG4
WREG5
WREG6
WREG7
WREG8
WREG9
WREG10
WREG11
WREG12
WREG13
WREG14
WREG15
SPLIM
0000
0002
0004
0006
0008
000A
000C
000E
0010
0012
0014
0016
0018
001A
001C
001E
0020
0022
0024
Working Register 0
Working Register 1
Working Register 2
Working Register 3
Working Register 4
Working Register 5
Working Register 6
Working Register 7
Working Register 8
Working Register 9
Working Register 10
Working Register 11
Working Register 12
Working Register 13
Working Register 14
Working Register 15
Stack Pointer Limit Register
ACCAL
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0800
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
0000
0000
0000
0000
xxxx
xxxx
xxxx
00xx
xxxx
00xx
0000
0020
ACCAL
ACCAH
ACCAU
ACCBL
ACCBH
ACCBU
PCL
ACCAH
0026 ACCA<39> ACCA<39> ACCA<39> ACCA<39> ACCA<39> ACCA<39> ACCA<39> ACCA<39>
ACCAU
0028
002A
ACCBL
ACCBH
002C ACCB<39> ACCB<39> ACCB<39> ACCB<39> ACCB<39> ACCB<39> ACCB<39> ACCB<39>
ACCBU
002E
0030
0032
0034
0036
0038
Program Counter Low Word Register
PCH
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Program Counter High Byte Register
Table Page Address Pointer Register
TBLPAG
PSVPAG
RCOUNT
DCOUNT
Program Memory Visibility Page Address Pointer Register
REPEATLoop Counter Register
DCOUNT<15:0>
DOSTARTL 003A
DOSTARTH 003C
DOSTARTL<15:1>
0
0
—
—
—
—
—
—
—
—
—
—
DOSTARTH<5:0>
DOENDH
DOENDL
DOENDH
SR
003E
0040
0042
0044
DOENDL<15:1>
—
OA
—
—
OB
—
SA
—
—
SB
US
—
—
—
SAB
—
DA
—
DC
—
—
OAB
EDT
IPL2
IPL1
IPL0
RA
N
OV
Z
C
CORCON
MODCON
Legend:
—
DL2
DL1
DL0
SATA SATB SATDW ACCSAT IPL3
YWM3 YWM2 YWM1
PSV
RND
IF
0046 XMODEN
YMODEN
—
BWM3
BWM2
BWM1
BWM0
YWM0 XWM3 XWM2 XWM1 XWM0 0000
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-1:
CPU CORE REGISTER MAP (CONTINUED)
SFR
Addr
All
Resets
File Name
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
XMODSRT 0048
XMODEND 004A
YMODSRT 004C
YMODEND 004E
XS<15:1>
XE<15:1>
YS<15:1>
YE<15:1>
XB9
0
1
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
0
1
XBREV
0050
0052
BREN
—
XB14
—
XB13
XB12
XB11
XB10
XB8
XB7
XB6
XB5
XB4
XB3
XB2
XB1
XB0
DISICNT
Legend:
Disable Interrupts Counter Register
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-2:
CHANGE NOTIFICATION REGISTER MAP FOR dsPIC33FJ06GS101
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
CN3IE
Bit 2
Bit 1
CN1IE
Bit 0
CN0IE
CNEN1
CNPU1
Legend:
0060
0068
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
CN7IE
CN6IE
CN5IE
CN4IE
CN2IE
0000
0000
CN7PUE
CN6PUE
CN5PUE
CN4PUE
CN3PUE CN2PUE CN1PUE CN0PUE
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-3:
CHANGE NOTIFICATION REGISTER MAP FOR dsPIC33FJ06GS102, dsPIC33FJ06GS202, dsPIC33FJ16GS402 AND
dsPIC33FJ16GS502
File
Name Addr
SFR
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CNEN1 0060
CN15IE
CN14IE
CN13IE
CN12IE
CN11IE
CN10IE
CN9IE
CN8IE
CN7IE
CN6IE
CN5IE
CN4IE
CN3IE
CN2IE
CN1IE
CN0IE
0000
0000
CNPU1 0068 CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE CN8PUE CN7PUE CN6PUE CN5PUE CN4PUE CN3PUE CN2PUE CN1PUE CN0PUE
Legend: x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-4:
CHANGE NOTIFICATION REGISTER MAP FOR dsPIC33FJ16GS404 AND dsPIC33FJ16GS504
File
Name Addr
SFR
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CNEN1 0060
CNEN2 0062
CN15IE
—
CN14IE
—
CN13IE
CN29IE
CN12IE
CN28IE
CN11IE
CN27IE
CN10IE
CN26IE
CN9IE
CN8IE
CN7IE
CN6IE
CN5IE
CN4IE
CN3IE
CN2IE
CN1IE
CN0IE
0000
0000
CN25IE
CN24IE
CN23IE
CN22IE
CN21IE
CN20IE
CN19IE
CN18IE
CN17IE
CN16IE
CNPU1 0068 CN15PUE CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE CN9PUE CN8PUE CN7PUE CN6PUE CN5PUE CN4PUE CN3PUE CN2PUE CN1PUE CN0PUE 0000
CNPU2 006A
—
—
CN29PUE CN28PUE CN27PUE CN26PUE CN25PUE CN24PUE CN23PUE CN22PUE CN21PUE CN20PUE CN19PUE CN18PUE CN17PUE CN16PUE 0000
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-5:
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ06GS101 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INTCON1 0080 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE
OVBTE
COVTE SFTACERR DIV0ERR
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
MATHERR ADDRERR STKERR OSCFAIL
—
0000
INTCON2 0082 ALTIVT
DISI
—
—
ADIF
INT2IF
—
—
U1TXIF
—
—
U1RXIF
—
—
SPI1IF
—
—
SPI1EIF
—
—
—
—
T2IF
—
—
—
—
—
—
T2IE
—
—
—
—
—
—
—
—
—
—
-—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
T1IF
CNIF
—
INT2EP
OC1IF
—
INT1EP
—
INT0EP 0000
INT0IF 0000
SI2C1IF 0000
IFS0
IFS1
IFS3
IFS4
IFS5
IFS6
IFS7
IEC0
IEC1
IEC2
IEC3
IEC4
IEC5
IEC6
IEC7
IPC0
IPC1
IPC2
IPC3
IPC4
IPC5
IPC7
IPC14
IPC16
IPC23
IPC24
IPC27
IPC28
0084
0086
008A
008C
008E
—
—
—
—
—
—
—
INT1IF
—
MI2C1IF
—
—
—
—
—
PSEMIF
—
—
—
—
—
0000
0000
0000
0000
0000
0000
—
—
—
—
—
—
—
—
—
U1EIF
—
PWM1IF
—
—
—
—
—
—
—
—
—
—
0090 ADCP1IF ADCP0IF
—
—
—
—
—
—
—
—
—
PWM4IF
ADCP3IF
—
—
0092
0094
0096
0098
009A
009C
009E
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADIE
INT2IE
—
U1TXIE
—
U1RXIE
—
SPI1IE
—
SPI1EIE
—
—
—
T1IE
CNIE
—
OC1IE
—
INT0IE
—
—
INT1IE
—
MI2C1IE
—
SI2C1IE 0000
—
—
—
—
—
—
—
—
—
—
—
—
—
0000
0000
0000
0000
0000
0000
—
—
—
—
—
PSEMIE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
U1EIE
—
PWM1IE
—
—
—
—
—
—
—
—
—
00A0 ADCP1IE ADCP0IE
—
—
—
—
—
—
—
—
—
PWM4IE
ADCP3IE
INT0IP1
—
00A2
00A4
00A6
00A8
00AA
00AC
00AE
00B2
00C0
00C4
00D2
00D4
00DA
00DC
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
T1IP2
T2IP2
T1IP1
T2IP1
T1IP0
T2IP0
—
OC1IP2
—
OC1IP1
—
OC1IP0
—
—
—
INT0IP2
—
INT0IP2 4404
—
—
—
—
—
4000
4440
U1RXIP2 U1RXIP1 U1RXIP0
—
SPI1IP2
—
SPI1IP1
—
SPI1IP0
—
SPI1EIP2 SPI1EIP1 SPI1EIP0
ADIP2 ADIP1 ADIP0
MI2C1IP2 MI2C1IP1 MI2C1IP0
—
—
—
—
CNIP2
—
—
CNIP1
—
—
CNIP0
—
—
—
U1TXIP2 U1TXIP1 U1TXIP0 0044
SI2C1IP2 SI2C1IP1 SI2C1IP0 4044
INT1IP2 INT1IP21 INT1IP0 0004
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
INT2IP2
INT2IP1
INT2IP0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0040
0040
0400
0040
4400
0040
0000
—
—
—
—
—
—
—
PSEMIP2 PSEMIP1 PSEMIP0
—
—
—
—
—
—
—
—
U1EIP2
—
U1EIP1
—
U1EIP0
—
—
—
—
—
—
PWM1IP2 PWM1IP1 PWM1IP0
—
—
—
—
—
—
—
—
PWM4IP2 PWM4IP1 PWM4IP0
—
ADCP1IP2 ADCP1IP1 ADCP1IP0
—
ADCP0IP2 ADCP0IP1 ADCP0IP0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP3IP2 ADCP3IP1 ADCP3IP0
—
INTTREG 00E0
Legend:
ILR3
ILR2
ILR1
ILR0
VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0 0000
x
= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-6:
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ06GS102 DEVICES ONLY
File
Name Addr
SFR
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INTCON1 0080 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE
OVBTE
COVTE SFTACERR DIV0ERR
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
MATHERR ADDRERR STKERR OSCFAIL
—
INT0EP
INT0IF
SI2C1IF
—
0000
0000
0000
0000
0000
0000
0000
0000
INTCON2 0082 ALTIVT
DISI
—
—
ADIF
INT2IF
—
—
U1TXIF
—
—
U1RXIF
—
—
SPI1IF
—
—
SPI1EIF
—
—
—
—
T2IF
—
—
—
—
—
—
T2IE
—
—
—
—
—
—
—
—
—
-—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
T1IF
CNIF
—
INT2EP
OC1IF
—
INT1EP
—
IFS0
IFS1
IFS3
IFS4
IFS5
IFS6
IFS7
IEC0
IEC1
IEC3
IEC4
IEC5
IEC6
IEC7
IPC0
IPC1
IPC2
IPC3
IPC4
IPC5
IPC7
IPC14
IPC16
IPC23
IPC27
IPC28
0084
0086
008A
008C
—
—
—
—
—
—
INT1IF
—
MI2C1IF
—
—
—
—
—
PSEMIF
—
—
—
—
—
—
—
—
—
—
—
—
U1EIF
—
—
008E PWM2IF PWM1IF
0090 ADCP1IF ADCP0IF
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0092
0094
0096
009A
009C
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP2IF 0000
ADIE
INT2IE
—
U1TXIE
—
U1RXIE
—
SPI1IE
—
SPI1EIE
—
—
—
T1IE
CNIE
—
OC1IE
—
—
INT0IE
SI2C1IE
—
0000
0000
0000
0000
0000
0000
—
INT1IE
—
MI2C1IE
—
—
—
—
PSEMIE
—
—
—
—
—
—
—
—
—
—
—
U1EIE
—
—
009E PWM2IE PWM1IE
00A0 ADCP1IE ADCP0IE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
00A2
00A4
00A6
00A8
00AA
00AC
00AE
00B2
00C0
00C4
00D2
00DA
00DC
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP2IE 0000
T1IP2
T2IP2
T1IP1
T2IP1
T1IP0
T2IP0
—
OC1IP2
—
OC1IP1
—
OC1IP0
—
—
—
INT0IP2
—
INT0IP1
—
INT0IP0
—
4404
4000
4440
—
—
—
U1RXIP2 U1RXIP2 U1RXIP0
—
SPI1IP2
—
SPI1IP1
—
SPI1IP0
—
SPI1EIP2 SPI1EIP1 SPI1EIP0
ADIP2 ADIP1 ADIP0
MI2C1IP2 MI2C1IP1 MI2C1IP0
—
—
—
—
—
CNIP2
—
—
CNIP1
—
—
CNIP0
—
—
—
U1TXIP2 U1TXIP1 U1TXIP0 0044
SI2C1IP2 SI2C1IP1 SI2C1IP0 4044
—
—
—
—
—
—
—
—
—
—
—
—
—
INT1IP2
INT1IP1
INT1IP0
—
0004
0040
0040
0040
4400
4400
—
—
—
—
—
—
—
INT2IP2
INT2IP1
INT2IP0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PSEMIP2 PSEMIP1 PSEMIP0
—
—
—
—
—
—
—
—
—
U1EIP2
—
U1EIP1
—
U1EIP0
—
—
—
PWM2IP2 PWM2IP1 PWM2IP0
ADCP1IP2 ADCP1IP1 ADCP1IP0
—
PWM1IP2 PWM1IP1 PWM1IP0
ADCP0IP2 ADCP0IP1 ADCP0IP0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP2IP2 ADCP2IP1 ADCP2IP0 0004
INTTREG 00E0
Legend:
ILR3
ILR2
ILR1
ILR0
VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0 0000
x
= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-7:
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ06G202 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INTCON1 0080 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE
OVBTE
—
COVTE SFTACERR DIV0ERR
—
—
MATHERR ADDRERR STKERR OSCFAIL
—
INT0EP
INT0IF
SI2C1IF
—
0000
0000
0000
0000
0000
0000
0000
0000
INTCON2 0082 ALTIVT
DISI
—
—
ADIF
INT2IF
—
—
U1TXIF
—
—
U1RXIF
—
—
SPI1IF
—
—
—
—
T2IF
—
—
—
—
—
—
T1IF
CNIF
—
INT2EP
OC1IF
AC1IF
—
INT1EP
IC1IF
MI2C1IF
—
IFS0
0084
0086
008A
008C
—
—
—
—
SPI1EIF
—
—
IFS1
—
—
—
—
INT1IF
—
IFS3
—
—
—
—
PSEMIF
—
—
—
—
—
IFS4
—
—
—
—
—
—
—
—
—
—
—
—
U1EIF
—
—
IFS5
008E PWM2IF PWM1IF
0090 ADCP1IF ADCP0IF
—
—
—
—
—
—
—
—
—
—
—
—
—
IFS6
—
—
—
—
—
—
AC2IF
—
—
—
—
—
—
—
—
IFS7
0092
0094
0096
009A
009C
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP6IF
—
—
—
—
ADCP2IF 0000
INT0IE 0000
SI2C1IE 0000
IEC0
IEC1
IEC3
IEC4
IEC5
IEC6
IEC7
IPC0
IPC1
IPC2
IPC3
IPC4
IPC5
IPC7
IPC14
IPC16
IPC23
IPC25
IPC27
IPC28
IPC29
ADIE
INT2IE
—
U1TXIE
—
U1RXIE
—
SPI1IE
—
SPI1EIE
—
—
T2IE
—
—
—
T1IE
CNIE
—
OC1IE
AC1IE
—
IC1IE
MI2C1IE
—
—
—
—
INT1IE
—
—
—
—
PSEMIE
—
—
—
—
—
—
—
—
—
0000
0000
0000
0000
—
—
—
—
—
—
—
—
—
—
—
U1EIE
—
009E PWM2IE PWM1IE
00A0 ADCP1IE ADCP0IE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
AC2IE
—
—
—
—
—
—
—
00A2
00A4
00A6
00A8
00AA
00AC
00AE
00B2
00C0
00C4
00D2
00D6
00DA
00DC
00DE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP6IE
IC1IP0
—
—
—
—
ADCP2IE 0000
T1IP2
T2IP2
T1IP1
T2IP1
T1IP0
T2IP0
—
OC1IP2
—
OC1IP1
—
OC1IP0
—
—
IC1IP2
—
IC1IP1
—
—
INT0IP2
—
INT0IP1
—
INT0IP0
—
4444
4000
4440
—
—
—
U1RXIP2 U1RXIP1 U1RXIP0
—
SPI1IP2
—
SPI1IP1
—
SPI1IP0
—
—
SPI1EIP2 SPI1EIP1 SPI1EIP0
ADIP2 ADIP1 ADIP0
MI2C1IP2 MI2C1IP1 MI2C1IP0
—
—
—
—
—
CNIP2
—
—
CNIP1
—
—
CNIP0
—
—
-—
—
—
U1TXIP2 U1TXIP1 U1TXIP0 0044
SI2C1IP2 SI2C1IP1 SI2C1IP0 4444
—
AC1IP2
—
AC1IP1
—
AC1IP0
—
—
—
—
—
—
—
—
INT1IP2
—
INT1IP1
—
INT1IP0
—
0004
0040
0040
0040
4400
4000
4400
—
—
—
—
—
—
—
—
INT2IP2
INT2IP1
INT2IP0
—
—
—
—
—
—
—
—
—
PSEMIP2 PSEMIP1 PSEMIP0
—
—
—
—
—
—
—
—
—
—
—
—
U1EIP2
—
U1EIP1
—
U1EIP0
—
—
—
—
—
PWM2IP2 PWM2IP1 PWM2IP0
AC2IP2 AC2IP1 AC2IP0
ADCP1IP2 ADCP1IP1 ADCP1IP0
—
PWM1IP2 PWM1IP1 PWM1IP0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP0IP2 ADCP0IP1 ADCP0IP0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP2IP2 ADCP2IP1 ADCP2IP0 0004
ADCP6IP2 ADCP6IP1 ADCP6IP0 0004
—
—
—
—
—
—
INTTREG 00E0
Legend:
ILR3
ILR2
ILR1
ILR0
—
VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0 0000
x
= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-8:
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ16GS402/404 DEVICES ONLY
File
Name Addr
SFR
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INTCON1 0080 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE
OVBTE
—
COVTE SFTACERR DIV0ERR
—
—
MATHERR ADDRERR STKERR OSCFAIL
—
INT0EP
INT0IF
SI2C1IF
—
0000
0000
0000
0000
0000
0000
0000
INTCON2 0082 ALTIVT
DISI
—
—
ADIF
INT2IF
—
—
U1TXIF
—
—
U1RXIF
—
—
SPI1IF
—
—
T3IF
—
—
T2IF
—
—
OC2IF
—
—
—
—
T1IF
CNIF
—
INT2EP
OC1IF
—
INT1EP
IC1IF
MI2C1IF
—
IFS0
0084
0086
008A
008C
—
—
—
—
SPI1EIF
—
IC2IF
—
IFS1
—
INT1IF
—
IFS3
—
—
—
—
PSEMIF
—
—
—
—
—
—
IFS4
—
—
—
—
—
—
—
—
—
—
—
—
U1EIF
—
—
IFS5
008E PWM2IF PWM1IF
0090 ADCP1IF ADCP0IF
—
—
—
—
—
—
—
—
—
—
—
—
—
IFS6
—
—
—
—
—
—
—
—
—
—
—
—
—
PWM3IF 0000
IFS7
0092
0094
0096
009A
009C
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP3IF ADCP2IF 0000
IEC0
IEC1
IEC3
IEC4
IEC5
IEC6
IEC7
IPC0
IPC1
IPC2
IPC3
IPC4
IPC5
IPC7
IPC14
IPC16
IPC23
IPC24
IPC27
IPC28
ADIE
INT2IE
—
U1TXIE
—
U1RXIE
—
SPI1IE
—
SPI1EIE
—
T3IE
—
T2IE
—
OC2IE
—
IC2IE
—
—
T1IE
CNIE
—
OC1IE
—
IC1IE
MI2C1IE
—
INT0IE
SI2C1IE
—
0000
0000
0000
0000
0000
INT1IE
—
—
—
—
PSEMIE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
U1EIE
—
—
009E PWM2IE PWM1IE
00A0 ADCP1IE ADCP0IE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PWM3IE 0000
00A2
00A4
00A6
00A8
00AA
00AC
00AE
00B2
00C0
00C4
00D2
00D4
00DA
00DC
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP3IE ADCP2IE 0000
T1IP2
T2IP2
T1IP1
T2IP1
T1IP0
T2IP0
—
OC1IP2
OC2IP2
SPI1IP2
—
OC1IP1
OC2IP1
SPI1IP1
—
OC1IP0
OC2IP0
SPI1IP0
—
—
IC1IP2
IC2IP2
IC1IP1
IC2IP1
IC1IP0
IC2IP0
—
INT0IP2
—
INT0IP1
—
INT0IP2
—
4444
4440
4444
—
—
—
U1RXIP2 U1RXIP1 U1RXIP0
—
—
SPI1EIP2 SPI1EIP1 SPI1EIP0
ADIP2 ADIP1 ADIP0
MI2C1IP2 MI2C1IP1 MI2C1IP0
—
T3IP2
T3IP1
T3IP0
—
CNIP2
—
—
CNIP1
—
—
CNIP0
—
—
-—
—
—
U1TXIP2 U1TXIP1 U1TXIP0 0044
SI2C1IP2 SI2C1IP1 SI2C1IP0 4044
—
—
—
—
—
—
—
—
—
—
—
—
—
—
INT1IP2
INT1IP1
INT1IP0
0004
0040
0040
0040
4400
—
—
—
—
—
—
—
—
INT2IP2
INT2IP1
INT2IP0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PSEMIP2 PSEMIP1 PSEMIP0
—
—
—
—
—
—
—
—
—
U1EIP2
—
U1EIP1
—
U1EIP0
—
—
PWM2IP2 PWM2IP1 PWM2IP0
—
PWM1IP2 PWM1IP1 PWM1IP0
-—
—
—
—
—
—
—
—
—
—
—
—
PWM3IP2 PWM3IP1 PWM3IP0 0004
4400
ADCP2IP2 ADCP2IP1 ADCP2IP0 0044
ADCP1IP2 ADCP1IP1 ADCP1IP0
—
ADCP0IP2 ADCP0IP1 ADCP0IP0
-—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP3IP2 ADCP3IP1 ADCP3IP0
—
INTTREG 00E0
Legend:
ILR3
ILR2
ILR1
ILR0
—
VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0 0000
x
= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-9:
INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ16GS502 DEVICES ONLY
File
Name Addr
SFR
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INTCON1 0080 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE
OVBTE
—
COVTE SFTACERR DIV0ERR
—
—
MATHERR ADDRERR STKERR OSCFAIL
—
INT0EP
INT0IF
SI2C1IF
—
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
4444
4440
4444
0044
4444
0004
0040
0040
0040
4400
INTCON2 0082 ALTIVT
DISI
—
—
ADIF
INT2IF
—
—
U1TXIF
—
—
U1RXIF
—
—
SPI1IF
—
—
T3IF
—
—
T2IF
—
—
OC2IF
—
—
—
—
T1IF
CNIF
—
INT2EP
OC1IF
AC1IF
—
INT1EP
IC1IF
MI2C1IF
—
IFS0
0084
0086
008A
008C
—
—
—
—
SPI1EIF
—
IC2IF
—
IFS1
—
INT1IF
—
IFS3
—
—
—
—
PSEMIF
—
—
—
—
—
IFS4
—
—
—
—
—
—
—
—
—
—
—
—
U1EIF
—
—
IFS5
008E PWM2IF PWM1IF
0090 ADCP1IF ADCP0IF
—
—
—
—
—
—
—
—
—
—
—
—
—
IFS6
—
—
—
—
AC4IF
—
AC3IF
—
AC2IF
—
—
—
—
—
—
PWM4IF
PWM3IF
IFS7
0092
0094
0096
009A
009C
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP6IF
—
—
—
ADCP3IF ADCP2IF
IEC0
IEC1
IEC3
IEC4
IEC5
IEC6
IEC7
IPC0
IPC1
IPC2
IPC3
IPC4
IPC5
IPC7
IPC14
IPC16
IPC23
IPC24
IPC25
IPC26
IPC27
IPC28
IPC29
ADIE
INT2IE
—
U1TXIE
—
U1RXIE
—
SPI1IE
—
SPI1EIE
—
T3IE
—
T2IE
—
OC2IE
—
IC2IE
—
T1IE
CNIE
—
OC1IE
AC1IE
—
IC1IE
MI2C1IE
—
INT0IE
SI2C1IE
—
INT1IE
—
—
—
—
PSEMIE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
U1EIE
—
—
009E PWM2IE PWM1IE
00A0 ADCP1IE ADCP0IE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
AC4IE
—
AC3IE
—
AC2IE
—
—
—
—
—
—
PWM4IE
PWM3IE
00A2
00A4
00A6
00A8
00AA
00AC
00AE
00B2
00C0
00C4
00D2
00D4
00D6
00D8
00DA
00DC
00DE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP6IE
IC1IP0
IC2IP0
—
—
ADCP3IE ADCP2IE
T1IP2
T2IP2
T1IP1
T2IP1
T1IP0
T2IP0
—
OC1IP2
OC2IP2
SPI1IP2
—
OC1IP1
OC2IP1
SPI1IP1
—
OC1IP0
OC2IP0
SPI1IP0
—
—
IC1IP2
IC2IP2
IC1IP1
IC2IP1
—
INT0IP2
—
INT0IP1
—
INT0IP2
—
—
—
-—
—
U1RXIP2 U1RXIP1 U1RXIP0
—
—
SPI1EIP2 SPI1EIP1 SPI1EIP0
ADIP2 ADIP1 ADIP0
MI2C1IP2 MI2C1IP1 MI2C1IP0
T3IP2
T3IP1
T3IP0
—
CNIP2
—
—
CNIP1
—
—
CNIP0
—
-—
—
-—
—
—
U1TXIP2 U1TXIP1 U1TXIP0
SI2C1IP2 SI2C1IP1 SI2C1IP0
AC1IP2
—
AC1IP1
—
AC1IP0
—
—
—
—
—
—
—
—
INT1IP2
INT1IP1
INT1IP0
—
—
—
—
—
—
—
—
INT2IP2
INT2IP1
INT2IP0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PSEMIP2 PSEMIP1 PSEMIP0
—
—
—
—
—
—
—
—
—
U1EIP2
—
U1EIP1
—
U1EIP0
—
—
PWM2IP2 PWM2IP1 PWM2IP0
—
PWM1IP2 PWM1IP1 PWM1IP0
—
—
—
AC2IP2
—
—
AC2IP1
—
—
AC2IP0
—
—
—
—
—
—
—
—
—
—
—
—
PWM4IP2 PWM4IP1 PWM4IP0
—
PWM3IP2 PWM3IP1 PWM3IP0 0044
—
—
—
AC4IP2
—
—
AC4IP1
—
—
AC4IP0
—
—
—
AC3IP2
—
—
AC3IP1
—
—
AC3IP0
—
4000
0044
4400
—
—
—
ADCP1IP2 ADCP1IP1 ADCP1IP0
—
ADCP0IP2 ADCP0IP1 ADCP0IP0
-—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP3IP2 ADCP3IP1 ADCP3IP0
—
ADCP2IP2 ADCP2IP1 ADCP2IP0 0044
ADCP6IP2 ADCP6IP1 ADCP6IP0 0004
—
—
—
—
—
—
INTTREG 00E0
Legend:
ILR3
ILR2
ILR1
ILR0
—
VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0 0000
x
= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-10: INTERRUPT CONTROLLER REGISTER MAP FOR dsPIC33FJ16GS504 DEVICES ONLY
File
Name Addr
SFR
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INTCON1 0080 NSTDIS OVAERR OVBERR COVAERR COVBERR OVATE
OVBTE
—
COVTE SFTACERR DIV0ERR
—
—
MATHERR ADDRERR STKERR OSCFAIL
—
INT0EP
INT0IF
SI2C1IF
—
0000
0000
0000
0000
0000
0000
0000
INTCON2 0082 ALTIVT
DISI
—
—
ADIF
INT2IF
—
—
U1TXIF
—
—
U1RXIF
—
—
SPI1IF
—
—
T3IF
—
—
T2IF
—
—
OC2IF
—
—
—
—
T1IF
CNIF
—
INT2EP
OC1IF
AC1IF
—
INT1EP
IC1IF
IFS0
0084
0086
008A
008C
—
—
—
—
SPI1EIF
—
IC2IF
—
IFS1
—
INT1IF
—
MI2C1IF
—
IFS3
—
—
—
—
PSEMIF
—
—
—
—
—
IFS4
—
—
—
—
—
—
—
—
—
—
—
—
U1EIF
—
—
IFS5
008E PWM2IF PWM1IF
0090 ADCP1IF ADCP0IF
—
—
—
—
—
—
—
—
—
—
—
—
—
IFS6
—
—
—
—
AC4IF
—
AC3IF
—
AC2IF
—
—
—
—
—
—
PWM4IF
PWM3IF 0000
IFS7
0092
0094
0096
009A
009C
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP6IF ADCP5IF ADCP4IF ADCP3IF ADCP2IF 0000
IEC0
IEC1
IEC3
IEC4
IEC5
IEC6
IEC7
IPC0
IPC1
IPC2
IPC3
IPC4
IPC5
IPC7
IPC14
IPC16
IPC23
IPC24
IPC25
IPC26
IPC27
IPC28
IPC29
ADIE
INT2IE
—
U1TXIE
—
U1RXIE
—
SPI1IE
—
SPI1EIE
—
T3IE
—
T2IE
—
OC2IE
—
IC2IE
—
—
INT1IE
—
T1IE
CNIE
—
OC1IE
AC1IE
—
IC1IE
MI2C1IE
—
INT0IE
SI2C1IE
—
0000
0000
0000
0000
0000
—
—
—
PSEMIE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
U1EIE
—
—
009E PWM2IE PWM1IE
00A0 ADCP1IE ADCP0IE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
AC4IE
—
AC3IE
—
AC2IE
—
—
—
—
—
—
PWM4IE
PWM3IE 0000
00A2
00A4
00A6
00A8
00AA
00AC
00AE
00B2
00C0
00C4
00D2
00D4
00D6
00D8
00DA
00DC
00DE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ADCP6IE ADCP5IE ADCP4IE ADCP3IE ADCP2IE 0000
T1IP2
T2IP2
T1IP1
T2IP1
T1IP0
T2IP0
—
OC1IP2
OC2IP2
SPI1IP2
—
OC1IP1
OC2IP1
SPI1IP1
—
OC1IP0
OC2IP0
SPI1IP0
—
—
IC1IP2
IC2IP2
IC1IP1
IC2IP1
IC1IP0
IC2IP0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
INT0IP2
—
INT0IP1
—
INT0IP2
—
4444
4440
4444
—
—
U1RXIP2 U1RXIP1 U1RXIP0
—
—
SPI1EIP2 SPI1EIP1 SPI1EIP0
ADIP2 ADIP1 ADIP0
MI2C1IP2 MI2C1IP1 MI2C1IP0
T3IP2
T3IP1
T3IP0
—
CNIP2
—
—
CNIP1
—
—
CNIP0
—
—
-—
—
U1TXIP2 U1TXIP1
SI2C1IP2 SI2C1IP1 SI2C1IP0 4444
U1TXIP0 0044
—
AC1IP2
—
AC1IP1
—
AC1IP0
—
—
—
—
—
—
INT1IP2
INT1IP1
INT1IP0
0004
0040
0040
0040
4400
—
—
—
—
—
—
—
—
INT2IP2
INT2IP1
INT2IP0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PSEMIP2 PSEMIP1 PSEMIP0
—
—
—
—
—
—
—
—
U1EIP2
—
U1EIP1
—
U1EIP0
—
PWM2IP2 PWM2IP1 PWM2IP0
—
PWM1IP2 PWM1IP1 PWM1IP0
—
—
AC2IP2
—
—
AC2IP1
—
—
AC2IP0
—
—
—
—
—
—
—
—
—
—
—
—
PWM4IP2 PWM4IP1 PWM4IP0
PWM3IP2 PWM3IP1 PWM3IP0 0044
—
—
—
AC4IP2
—
—
AC4IP1
—
—
AC4IP0
—
—
AC3IP2
—
—
AC3IP1
—
—
AC3IP0
—
4000
0440
4400
—
—
ADCP1IP2 ADCP1IP1 ADCP1IP0
ADCP5IP2 ADCP5IP1 ADCP5IP0
—
ADCP0IP2 ADCP0IP1 ADCP0IP0
ADCP4IP2 ADCP4IP1 ADCP4IP0
—
—
—
ADCP3IP2 ADCP3IP1 ADCP3IP0
ADCP2IP2 ADCP2IP1 ADCP2IP0 4444
ADCP6IP2 ADCP6IP1 ADCP6IP0 0004
—
—
—
—
—
—
—
—
—
—
—
—
—
—
INTTREG 00E0
Legend:
ILR3
ILR2
ILR1
ILR0
—
VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0 0000
x
= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-11: TIMER REGISTER MAP FOR dsPIC33FJ06GS101 AND dsPIC33FJ06GSX02
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TMR1
0100
0102
0104
0106
010C
0110
Timer1 Register
Period Register 1
0000
FFFF
0000
0000
FFFF
0000
PR1
T1CON
TMR2
PR2
TON
TON
—
—
TSIDL
TSIDL
—
—
—
—
—
—
—
—
—
—
TGATE TCKPS1 TCKPS0
TGATE TCKPS1 TCKPS0
—
—
TSYNC
—
TCS
TCS
—
—
Timer2 Register
Period Register 2
T2CON
Legend:
—
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-12: TIMER REGISTER MAP FOR dsPIC33FJ16GSX02 AND dsPIC33FJ16GSX04
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TMR1
0100
0102
0104
0106
0108
010A
010C
010E
0110
0112
Timer1 Register
Period Register 1
0000
FFFF
0000
0000
xxxx
0000
FFFF
FFFF
0000
0000
PR1
T1CON
TMR2
TON
—
TSIDL
—
—
—
—
—
—
TGATE TCKPS1 TCKPS0
—
TSYNC
TCS
—
Timer2 Register
TMR3HLD
TMR3
Timer3 Holding Register (for 32-bit timer operations only)
Timer3 Register
PR2
Period Register 2
PR3
Period Register 3
T2CON
T3CON
Legend:
TON
TON
—
—
TSIDL
TSIDL
—
—
—
—
—
—
—
—
—
—
—
—
TGATE TCKPS1 TCKPS0
TGATE TCKPS1 TCKPS0
T32
—
—
—
TCS
TCS
—
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-13: INPUT CAPTURE REGISTER MAP FOR dsPIC33FJ06GS202
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
IC1BUF
IC1CON
Legend:
0140
0142
Input Capture 1 Register
ICTMR
xxxx
0000
—
—
ICSIDL
—
—
—
—
—
ICI1
ICI0
ICOV
ICBNE
ICM2
ICM1
ICM0
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-14: INPUT CAPTURE REGISTER MAP FOR dsPIC33FJ16GSX02 AND dsPIC33FJ16GSX04
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
IC1BUF
IC1CON
IC2BUF
IC2CON
Legend:
0140
0142
0144
0146
Input Capture 1 Register
ICTMR
Input Capture 2 Register
ICTMR
xxxx
0000
xxxx
0000
—
—
—
—
ICSIDL
ICSIDL
—
—
—
—
—
—
—
—
ICI1
ICI1
ICI0
ICI0
ICOV
ICOV
ICBNE
ICBNE
ICM2
ICM2
ICM1
ICM1
ICM0
ICM0
—
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-15: OUTPUT COMPARE REGISTER MAP FOR dsPIC33FJ06GS101 AND dsPIC33FJ06GSX02
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
OC1RS
OC1R
0180
0182
0184
Output Compare 1 Secondary Register
Output Compare 1 Register
xxxx
xxxx
0000
OC1CON
Legend:
—
—
OCSIDL
—
—
—
—
—
—
—
—
OCFLT
OCTSEL OCM2 OCM1 OCM0
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-16: OUTPUT COMPARE REGISTER MAP FOR dsPIC33FJ16GSX02 AND dsPIC33FJ06GSX04
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
OC1RS
OC1R
0180
0182
0184
0186
0188
018A
Output Compare 1 Secondary Register
Output Compare 1 Register
xxxx
xxxx
0000
xxxx
xxxxx
0000
OC1CON
OC2RS
OC2R
—
—
—
—
OCSIDL
OCSIDL
—
—
—
—
—
—
—
—
—
—
—
—
OCFLT
OCFLT
OCTSEL
OCTSEL
OCM2
OCM2
OCM1 OCM0
OCM1 OCM0
Output Compare 2 Secondary Register
Output Compare 2 Register
OC2CON
Legend:
—
—
—
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-17: HIGH-SPEED PWM REGISTER MAP
File
Name
SFR
Addr
All
Resets
Bit 15 Bit 14
Bit 13
Bit 12
Bit 11 Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PTCON
PTCON2
PTPER
0400 PTEN
—
—
PTSIDL SESTAT SEIEN EIPU SYNCPOL SYNCOEN SYNCEN
—
—
SYNCSRC1 SYNCSRC0 SEVTPS3 SEVTPS2 SEVTPS1 SEVTPS0 0000
0402
0404
—
—
—
—
—
—
—
—
—
—
—
PCLKDIV2 PCLKDIV1 PCLKDIV0 0000
PTPER<15:0>
FFF8
SEVTCMP 0406
SEVTCMP<15:3>
—
—
—
0000
0000
MDC
040A
MDC<15:0>
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-18: HIGH-SPEED PWM GENERATOR 1 REGISTER MAP
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PWMCON1 0420 FLTSTAT CLSTAT TRGSTAT FLTIEN
IOCON1 0422 PENH PENL POLH POLL
CLIEN
TRGIEN
ITB
MDCS
DTC1
DTC0
—
—
—
CAM
XPRES
SWAP
IUE
0000
0000
PMOD1
PMOD0 OVRENH OVRENL OVRDAT1 OVRDAT0 FLTDAT1
FLTDAT0
CLDAT1
CLDAT0
FLTPOL
OSYNC
FCLCON1 0424 IFLTMOD CLSRC4 CLSRC3 CLSRC2 CLSRC1 CLSRC0 CLPOL CLMOD FLTSRC4 FLTSRC3 FLTSRC2 FLTSRC1 FLTSRC0
FLTMOD1 FLTMOD0 0000
PDC1
0426
0428
042A
042C
042E
PDC1<15:0>
0000
0000
0000
0000
0000
0000
PHASE1
DTR1
PHASE1<15:0>
—
—
—
—
DTR1<13:0>
ALTDTR1<13:0>
SDC1<15:0>
ALTDTR1
SDC1
SPHASE1 0430
TRIG1 0432
TRGCON1 0434 TRGDIV3 TRGDIV2 TRGDIV1 TRGDIV0
STRIG1 0436
SPHASE1<15:0>
TRGCMP<15:3>
—
—
—
0000
—
—
—
—
DTM
—
TRGSTRT5 TRGSTRT4 TRGSTRT3 TRGSTRT2 TRGSTRT1 TRGSTRT0 0000
STRGCMP<15:3>
PWMCAP1<15:3>
—
—
—
—
—
—
—
—
—
0000
0000
0000
PWMCAP1 0438
LEBCON1 043A
PHR
PHF
PLR
PLF
FLTLEBEN CLLEBEN LEB6
LEB5
LEB4
LEB3
LEB2
LEB1
LEB0
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-19:
HIGH-SPEED PWM GENERATOR 2 REGISTER MAP FOR dsPIC33FJ06GS102/202 AND dsPIC33FJ16GSX02/X04 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PWMCON2 0440 FLTSTAT CLSTAT TRGSTAT FLTIEN
IOCON2 0442 PENH PENL POLH POLL
CLIEN
TRGIEN
ITB
MDCS
DTC1
DTC0
—
—
—
CAM
XPRES
SWAP
IUE
0000
0000
PMOD1
PMOD0 OVRENH OVRENL OVRDAT1 OVRDAT0 FLTDAT1
FLTDAT0
CLDAT1
CLDAT0
FLTPOL
OSYNC
FCLCON2 0444 IFLTMOD CLSRC4 CLSRC3 CLSRC2 CLSRC1 CLSRC0 CLPOL CLMOD FLTSRC4 FLTSRC3 FLTSRC2 FLTSRC1 FLTSRC0
FLTMOD1 FLTMOD0 0000
PDC2
0446
0448
044A
044C
044E
PDC2<15:0>
0000
0000
0000
0000
0000
0000
PHASE2
DTR2
PHASE2<15:0>
—
—
—
—
DTR2<13:0>
ALTDTR2<13:0>
SDC2<15:0>
ALTDTR2
SDC2
SPHASE2 0450
TRIG2 0452
TRGCON2 0454 TRGDIV3 TRGDIV2 TRGDIV1 TRGDIV0
STRIG2 0456
SPHASE2<15:0>
TRGCMP<15:3>
—
—
—
0000
—
—
—
—
DTM
—
TRGSTRT5 TRGSTRT4 TRGSTRT3 TRGSTRT2 TRGSTRT1 TRGSTRT0 0000
STRGCMP<15:3>
PWMCAP2<15:3>
—
—
—
—
—
—
—
—
—
0000
0000
0000
PWMCAP2 0458
LEBCON2 045A
PHR
PHF
PLR
PLF
FLTLEBEN CLLEBEN LEB6
LEB5
LEB4
LEB3
LEB2
LEB1
LEB0
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-20: HIGH-SPEED PWM GENERATOR 3 REGISTER MAP FOR dsPIC33FJ16GSX02/X04 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PWMCON3 0460 FLTSTAT CLSTAT TRGSTAT FLTIEN
CLIEN
TRGIEN
ITB
MDCS
DTC1
DTC0
—
—
—
CAM
XPRES
SWAP
IUE
0000
0000
IOCON3
FCLCON3
PDC3
0462
PENH
PENL
POLH
POLL
PMOD1
PMOD0 OVRENH OVRENL OVRDAT1 OVRDAT0 FLTDAT1
FLTDAT0
CLDAT1
CLDAT0
FLTPOL
OSYNC
0464 IFLTMOD CLSRC4 CLSRC3 CLSRC2 CLSRC1 CLSRC0 CLPOL CLMOD FLTSRC4 FLTSRC3 FLTSRC2 FLTSRC1 FLTSRC0
FLTMOD1 FLTMOD0 0000
0466
0468
046C
046C
046E
0470
0472
PDC3<15:0>
0000
0000
0000
0000
0000
0000
PHASE3
DTR3
PHASE3<15:0>
—
—
—
—
DTR3<13:0>
ALTDTR3<13:0>
SDC3<15:0>
ALTDTR3
SDC3
SPHASE3
TRIG3
SPHASE3<15:0>
TRGCMP<15:3>
—
—
—
0000
TRGCON3 0474 TRGDIV3 TRGDIV2 TRGDIV1 TRGDIV0
STRIG3 0476
—
—
—
—
DTM
—
TRGSTRT5 TRGSTRT4 TRGSTRT3 TRGSTRT2 TRGSTRT1 TRGSTRT0 0000
STRGCMP<15:3>
PWMCAP3<15:3>
—
—
—
—
—
—
—
—
—
0000
0000
0000
PWMCAP3 0478
LEBCON3 047A
PHR
PHF
PLR
PLF
FLTLEBEN CLLEBEN LEB6
LEB5
LEB4
LEB3
LEB2
LEB1
LEB0
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-21: HIGH-SPEED PWM GENERATOR 4 REGISTER MAP FOR dsPIC33FJ06GS101 AND dsPIC33FJ16GS50X DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PWMCON4 0480 FLTSTAT CLSTAT TRGSTAT FLTIEN
IOCON4 0482 PENH PENL POLH POLL
CLIEN
TRGIEN
ITB
MDCS
DTC1
DTC0
—
—
—
CAM
XPRES
SWAP
IUE
0000
0000
PMOD1
PMOD0 OVRENH OVRENL OVRDAT1 OVRDAT0 FLTDAT1
FLTDAT0
CLDAT1
FLTSRC0
CLDAT0
FLTPOL
OSYNC
FCLCON4 0484 IFLTMOD CLSRC4 CLSRC3 CLSRC2 CLSRC1 CLSRC0 CLPOL CLMOD FLTSRC4 FLTSRC3 FLTSRC2 FLTSRC1
FLTMOD1 FLTMOD0 0000
PDC4
0486
0488
048A
PDC4<15:0>
0000
0000
0000
0000
0000
0000
PHASE4
DTR4
PHASE4<15:0>
—
—
—
—
DTR4<13:0>
ALTDTR4<13:0>
SDC4<15:0>
ALTDTR4 048A
SDC4 048E
SPHASE4 0490
TRIG4 0492
TRGCON4 0494 TRGDIV3 TRGDIV2 TRGDIV1 TRGDIV0
STRIG4 0496
SPHASE4<15:0>
TRGCMP<15:3>
—
—
—
0000
—
—
—
—
DTM
—
TRGSTRT5 TRGSTRT4 TRGSTRT3 TRGSTRT2 TRGSTRT1 TRGSTRT0 0000
STRGCMP<15:3>
PWMCAP4<15:3>
—
—
—
—
—
—
—
—
—
0000
0000
0000
PWMCAP4 0498
LEBCON4 049A
PHR
PHF
PLR
PLF
FLTLEBEN CLLEBEN LEB6
LEB5
LEB4
LEB3
LEB2
LEB1
LEB0
Legend:
x
= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-22: I2C1 REGISTER MAP
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
I2C1RCV
I2C1TRN
I2C1BRG
I2C1CON
0200
0202
0204
0206
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
I2C1 Receive Register
I2C1 Transmit Register
0000
00FF
0000
1000
0000
0000
0000
—
—
—
Baud Rate Generator Register
I2CEN
I2CSIDL SCLREL IPMIEN
A10M
BCL
—
DISSLW
GCSTAT
SMEN
GCEN
STREN
I2COV
ACKDT
D_A
ACKEN
P
RCEN
S
PEN
R_W
RSEN
RBF
SEN
TBF
I2C1STAT 0208 ACKSTAT TRSTAT
—
—
—
—
—
—
—
—
—
ADD10
IWCOL
I2C1ADD
I2C1MSK 020C
Legend:
020A
—
—
—
—
I2C1 Address Register
AMSK<9:0>
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-23: UART1 REGISTER MAP
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
U1MODE
U1STA
0220
UARTEN
—
USIDL
IREN
—
RTSMD
—
UEN1
UEN0
TRMT
WAKE
LPBACK
ABAUD
URXINV
RIDLE
BRGH
PERR
PDSEL1 PDSEL0
STSEL
0000
0110
xxxx
0000
0000
0222 UTXISEL1 UTXINV UTXISEL0
UTXBRK UTXEN UTXBF
URXISEL1 URXISEL0 ADDEN
FERR
OERR
URXDA
U1TXREG 0224
U1RXREG 0226
—
—
—
—
—
—
—
—
—
—
—
—
—
UART1 Transmit Register
UART1 Receive Register
—
U1BRG
0228
Baud Rate Generator Prescaler
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-24: SPI1 REGISTER MAP
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
SPI1STAT
SPI1CON1
SPI1CON2
SPI1BUF
Legend:
0240
0242
0244
0248
SPIEN
—
—
—
SPISIDL
—
—
—
—
—
SMP
—
—
CKE
—
—
SSEN
—
SPIROV
CKP
—
MSTEN
—
—
SPRE2
—
—
SPRE1
—
—
SPRE0
—
SPITBF SPIRBF 0000
DISSCK DISSDO MODE16
PPRE1
PPRE0
—
0000
0000
0000
FRMEN SPIFSD FRMPOL
—
—
—
—
FRMDLY
SPI1 Transmit and Receive Buffer Register
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-25: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ06GS101 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15 Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ADCON 0300 ADON
—
—
—
ADSIDL SLOWCLK
—
—
—
GSWTRG
—
—
—
FORM
EIE
ORDER SEQSAMP ASYNCSAMP
—
ADCS2
PCFG2
—
ADCS1
PCFG1
P1RDY
ADCS0
PCFG0
P0RDY
—
0003
0000
0000
0000
ADPCFG 0302
ADSTAT 0306
ADBASE 0308
—
—
—
—
—
—
—
—
—
PCFG7 PCFG6
—
—
—
—
PCFG3
P3RDY
—
—
—
ADBASE<15:1>
ADCPC0 030A IRQEN1 PEND1 SWTRG1 TRGSRC14 TRGSRC13 TRGSRC12 TRGSRC11 TRGSRC10 IRQEN0 PEND0 SWTRG0 TRGSRC04 TRGSRC03 TRGSRC02 TRGSRC01 TRGSRC00 0000
ADCPC1 030C IRQEN3 PEND3 SWTRG3 TRGSRC34 TRGSRC33 TRGSRC32 TRGSRC31 TRGSRC30
—
—
—
—
—
—
—
—
0000
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
ADCBUF0 0320
ADCBUF1 0322
ADCBUF2 0324
ADCBUF3 0326
ADCBUF6 032C
ADCBUF7 032E
ADC Data Buffer 0
ADC Data Buffer 1
ADC Data Buffer 2
ADC Data Buffer 3
ADC Data Buffer 6
ADC Data Buffer 7
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-26: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ06GS102 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15 Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ADCON
0300 ADON
—
—
—
ADSIDL SLOWCLK
—
—
—
GSWTRG
—
—
—
FORM
EIE ORDER SEQSAMP ASYNCSAMP
—
PCFG3
—
ADCS2
PCFG2
P2RDY
ADCS1
PCFG1
P1RDY
ADCS0
PCFG0
P0RDY
—
0003
0000
0000
0000
ADPCFG 0302
—
—
—
—
—
—
—
—
—
—
—
—
—
PCFG5
—
PCFG4
—
ADSTAT
ADBASE
0306
0308
—
ADBASE<15:1>
ADCPC0 030A IRQEN1 PEND1 SWTRG1 TRGSRC14 TRGSRC13 TRGSRC12 TRGSRC11 TRGSRC10 IRQEN0 PEND0 SWTRG0 TRGSRC04 TRGSRC03 TRGSRC02 TRGSRC01 TRGSRC00 0000
ADCPC1 030C
ADCBUF0 0320
ADCBUF1 0322
ADCBUF2 0324
ADCBUF3 0326
ADCBUF4 0328
ADCBUF5 032A
—
—
—
—
—
—
—
—
IRQEN2 PEND2 SWTRG2 TRGSRC24 TRGSRC23 TRGSRC22 TRGSRC21 TRGSRC20 0000
ADC Data Buffer 0
ADC Data Buffer 1
ADC Data Buffer 2
ADC Data Buffer 3
ADC Data Buffer 4
ADC Data Buffer 5
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-27: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ06GS202 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15 Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ADCON
ADPCFG
ADSTAT
ADBASE
ADCPC0
ADCPC1
ADCPC3
0300 ADON
—
—
—
ADSIDL SLOWCLK
—
—
—
GSWTRG
—
—
—
FORM
—
EIE
—
ORDER SEQSAMP ASYNCSAMP
—
PCFG3
—
ADCS2
PCFG2
P2RDY
ADCS1
PCFG1
P1RDY
ADCS0
PCFG0
P0RDY
—
0003
0000
0000
0000
0302
0306
0308
—
—
—
—
—
—
—
—
—
PCFG5
—
PCFG4
—
—
—
P6RDY
ADBASE<15:1>
030A IRQEN1 PEND1 SWTRG1 TRGSRC14 TRGSRC13 TRGSRC12 TRGSRC11 TRGSRC10 IRQEN0 PEND0 SWTRG0 TRGSRC04 TRGSRC03 TRGSRC02 TRGSRC01 TRGSRC00 0000
030C
0310
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
IRQEN2 PEND2 SWTRG2 TRGSRC24 TRGSRC23 TRGSRC22 TRGSRC21 TRGSRC20 0000
IRQEN6 PEND6 SWTRG6 TRGSRC64 TRGSRC63 TRGSRC62 TRGSRC61 TRGSRC60 0000
ADCBUF0 0320
ADCBUF1 0322
ADCBUF2 0324
ADCBUF3 0326
ADCBUF4 0328
ADCBUF5 032A
ADCBUF12 0338
ADCBUF13 033A
ADC Data Buffer 0
ADC Data Buffer 1
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
ADC Data Buffer 2
ADC Data Buffer 3
ADC Data Buffer 4
ADC Data Buffer 5
ADC Data Buffer 12
ADC Data Buffer13
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-28: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ16GS402/404 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15 Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ADCON
0300 ADON
—
—
—
ADSIDL SLOWCLK
—
—
—
GSWTRG
—
—
—
FORM
EIE
ORDER SEQSAMP ASYNCSAMP
—
ADCS2
PCFG2
P2RDY
ADCS1
PCFG1
P1RDY
ADCS0
PCFG0
P0RDY
—
0003
0000
0000
0000
ADPCFG 0302
ADSTAT 0306
ADBASE 0308
—
—
—
—
—
—
—
—
—
PCFG7 PCFG6 PCFG5
PCFG4
—
PCFG3
P3RDY
—
—
—
—
ADBASE<15:1>
ADCPC0 030A IRQEN1 PEND1 SWTRG1 TRGSRC14 TRGSRC13 TRGSRC12 TRGSRC11 TRGSRC10 IRQEN0 PEND0 SWTRG0 TRGSRC04 TRGSRC03 TRGSRC02 TRGSRC01 TRGSRC00 0000
ADCPC1 030C IRQEN3 PEND3 SWTRG3 TRGSRC34 TRGSRC33 TRGSRC32 TRGSRC31 TRGSRC30 IRQEN2 PEND2 SWTRG2 TRGSRC24 TRGSRC23 TRGSRC22 TRGSRC21 TRGSRC20 0000
ADCBUF0 0320
ADCBUF1 0322
ADCBUF2 0324
ADCBUF3 0326
ADCBUF4 0328
ADCBUF5 032A
ADCBUF6 032C
ADCBUF7 032E
ADC Data Buffer 0
ADC Data Buffer 1
ADC Data Buffer 2
ADC Data Buffer 3
ADC Data Buffer 4
ADC Data Buffer 5
ADC Data Buffer 6
ADC Data Buffer 7
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-29: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ16GS502 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15 Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ADCON
ADPCFG
ADSTAT
ADBASE
ADCPC0
ADCPC1
ADCPC3
0300 ADON
—
—
—
ADSIDL SLOWCLK
—
—
—
GSWTRG
—
—
—
FORM
EIE
ORDER SEQSAMP ASYNCSAMP
—
ADCS2
PCFG2
P2RDY
ADCS1
PCFG1
P1RDY
ADCS0
PCFG0
P0RDY
—
0003
0000
0000
0000
0302
0306
0308
—
—
—
—
—
—
—
—
—
PCFG7 PCFG6 PCFG5
P6RDY
PCFG4
—
PCFG3
P3RDY
—
—
—
ADBASE<15:1>
030A IRQEN1 PEND1 SWTRG1 TRGSRC14 TRGSRC13 TRGSRC12 TRGSRC11 TRGSRC10 IRQEN0 PEND0 SWTRG0 TRGSRC04 TRGSRC03 TRGSRC02 TRGSRC01 TRGSRC00 0000
030C IRQEN3 PEND3 SWTRG3 TRGSRC34 TRGSRC33 TRGSRC32 TRGSRC31 TRGSRC30 IRQEN2 PEND2 SWTRG2 TRGSRC24 TRGSRC23 TRGSRC22 TRGSRC21 TRGSRC20 0000
0310
—
—
—
—
—
—
—
—
IRQEN6 PEND6 SWTRG6 TRGSRC64 TRGSRC63 TRGSRC62 TRGSRC61 TRGSRC60 0000
ADCBUF0 0320
ADCBUF1 0322
ADCBUF2 0324
ADCBUF3 0326
ADCBUF4 0328
ADCBUF5 032A
ADCBUF6 032C
ADCBUF7 032E
ADCBUF12 0338
ADCBUF13 033A
ADC Data Buffer 0
ADC Data Buffer 1
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
ADC Data Buffer 2
ADC Data Buffer 3
ADC Data Buffer 4
ADC Data Buffer 5
ADC Data Buffer 6
ADC Data Buffer 7
ADC Data Buffer 12
ADC Data Buffer 13
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-30: HIGH-SPEED 10-BIT ADC REGISTER MAP FOR dsPIC33FJ16GS504 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15 Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ADCON
0300 ADON
—
—
—
ADSIDL SLOWCLK
—
PCFG11
—
GSWTRG
PCFG10
—
—
PCFG9
—
FORM
PCFG8
EIE
ORDER SEQSAMP ASYNCSAMP
—
ADCS2
PCFG2
P2RDY
ADCS1
PCFG1
P1RDY
ADCS0
PCFG0
P0RDY
—
0003
0000
0000
0000
ADPCFG
ADSTAT
ADBASE
ADCPC0
ADCPC1
ADCPC2
ADCPC3
0302
0306
0308
—
—
—
—
—
—
PCFG7 PCFG6 PCFG5
P6RDY P5RDY
PCFG4
P4RDY
PCFG3
P3RDY
—
—
ADBASE<15:1>
030A IRQEN1 PEND1 SWTRG1 TRGSRC14 TRGSRC13 TRGSRC12 TRGSRC11 TRGSRC10 IRQEN0 PEND0 SWTRG0 TRGSRC04 TRGSRC03 TRGSRC02 TRGSRC01 TRGSRC00 0000
030C IRQEN3 PEND3 SWTRG3 TRGSRC34 TRGSRC33 TRGSRC32 TRGSRC31 TRGSRC30 IRQEN2 PEND2 SWTRG2 TRGSRC24 TRGSRC23 TRGSRC22 TRGSRC21 TRGSRC20 0000
030E IRQEN5 PEND5 SWTRG5 TRGSRC54 TRGSRC53 TRGSRC52 TRGSRC51 TRGSRC50 IRQEN4 PEND4 SWTRG4 TRGSRC44 TRGSRC43 TRGSRC42 TRGSRC41 TRGSRC40 0000
0310
—
—
—
—
—
—
—
—
IRQEN6 PEND6 SWTRG6 TRGSRC64 TRGSRC63 TRGSRC62 TRGSRC61 TRGSRC60 0000
ADCBUF0 0320
ADCBUF1 0322
ADCBUF2 0324
ADCBUF3 0326
ADCBUF4 0328
ADCBUF5 032A
ADCBUF6 032C
ADCBUF7 032E
ADCBUF8 0330
ADCBUF9 0332
ADCBUF10 0334
ADCBUF11 0336
ADCBUF12 0338
ADCBUF13 033A
ADC Data Buffer 0
ADC Data Buffer 1
ADC Data Buffer 2
ADC Data Buffer 3
ADC Data Buffer 4
ADC Data Buffer 5
ADC Data Buffer 6
ADC Data Buffer 7
ADC Data Buffer 8
ADC Data Buffer 9
ADC Data Buffer 10
ADC Data Buffer 11
ADC Data Buffer 12
ADC Data Buffer 13
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
xxxx
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-31: ANALOG COMPARATOR CONTROL REGISTER MAP FOR dsPIC33FJ06GS202 DEVICES ONLY
File
Name
All
Resets
ADR
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CMPCON1
CMPDAC1
CMPCON2
CMPDAC2
0540
0542
0544
0546
CMPON
—
—
—
—
—
CMPSIDL
—
—
—
—
—
—
—
—
—
—
—
—
—
—
DACOE INSEL1 INSEL0 EXTREF
—
CMPSTAT
—
CMPPOL RANGE 0000
CMREF<9:0>
0000
CMPPOL RANGE 0000
0000
CMPON
—
CMPSIDL
—
—
DACOE INSEL1 INSEL0 EXTREF
—
CMPSTAT
—
CMREF<9:0>
TABLE 4-32: ANALOG COMPARATOR CONTROL REGISTER MAP dsPIC33FJ16GS502/504 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CMPCON1
CMPDAC1
CMPCON2
CMPDAC2
CMPCON3
CMPDAC3
CMPCON4
CMPDAC4
0540
0542
0544
0546
0548
054A
054C
054E
CMPON
—
—
—
—
—
—
—
—
—
CMPSIDL
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
DACOE INSEL1 INSEL0 EXTREF
—
CMPSTAT
—
CMPPOL RANGE 0000
CMREF<9:0>
0000
CMPPOL RANGE 0000
0000
CMPON
—
CMPSIDL
—
—
—
—
DACOE INSEL1 INSEL0 EXTREF
—
CMPSTAT
CMPSTAT
CMPSTAT
—
—
—
CMREF<9:0>
CMPON
—
CMPSIDL
—
DACOE INSEL1 INSEL0 EXTREF
—
CMPPOL RANGE 0000
0000
CMREF<9:0>
CMPON
—
CMPSIDL
—
DACOE INSEL1 INSEL0 EXTREF
—
CMPPOL RANGE 0000
0000
CMREF<9:0>
TABLE 4-33: PERIPHERAL PIN SELECT INPUT REGISTER MAP
File
Name
SFR
Addr
All
Resets
Bit 15 Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RPINR0 0680
RPINR1 0682
RPINR2 0684
RPINR3 0686
RPINR7 068E
RPINR11 0696
RPINR18 06A4
RPINR20 06A8
RPINR21 06AA
RPINR29 06BA
RPINR30 06BC
RPINR31 06BE
RPINR32 06C0
RPINR33 06C2
RPINR34 06C4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
INT1R5
—
INT1R4
—
INT1R3
—
INT1R2
—
INT1R1
—
INT1R0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
3F00
003F
0000
3F3F
3F3F
INT2R5
—
INT2R4
—
INT2R3
—
INT2R2
—
INT2R1
—
INT2R0
—
T1CKR5
T3CKR5
IC2R5
—
T1CKR4
T3CKR4
IC2R4
—
T1CKR3
T3CKR3
IC2R3
—
T1CKR2
T3CKR2
IC2R2
—
T1CKR1
T3CKR1
IC2R1
—
T1CKR0
T3CKR0
IC2R0
—
T2CKR5
IC1R5
OCFAR5
U1RXR5
SDI1R5
SS1R5
—
T2CKR4
IC1R4
T2CKR3
IC1R3
OCFAR3
U1RXR3
SDI1R3
SS1R3
—
T2CKR2
IC1R2
T2CKR1
IC1R1
T2CKR0
IC1R0
OCFAR4
U1RXR4
SDI1R4
SS1R54
—
OCFAR2 OCFAR1 OCFAR0 3F3F
U1CTSR5 U1CTSR4 U1CTSR3 U1CTSR2 U1CTSR1 U1CTSR0
U1RXR2
SDI1R2
SS1R2
—
U1RXR1
SDI1R1
SS1R1
—
U1RXR0 003F
SCK1R5
—
SCK1R4
—
SCK1R3
—
SCK1R2
—
SCK1R1
—
SCK1R0
—
SDI1R0
SS1R0
—
3F3F
0000
3F00
3F3F
3F3F
3F3F
3F3F
FLT1R5
FLT3R5
FLT5R5
FLT7R5
FLT1R4
FLT3R4
FLT5R4
FLT7R4
FLT1R3
FLT3R3
FLT5R3
FLT7R3
FLT1R2
FLT3R2
FLT5R2
FLT7R2
FLT1R1
FLT3R1
FLT5R1
FLT7R1
FLT1R0
FLT3R0
FLT5R0
FLT7R0
FLT2R5
FLT4R5
FLT6R5
FLT8R5
FLT2R4
FLT4R4
FLT6R4
FLT8R4
FLT2R3
FLT4R3
FLT6R3
FLT8R3
FLT2R2
FLT4R2
FLT6R2
FLT8R2
FLT2R1
FLT4R1
FLT6R1
FLT8R1
FLT2R0
FLT4R0
FLT6R0
FLT8R0
SYNCI1R5 SYNCI1R4 SYNCI1R3 SYNCI1R2 SYNCI1R1 SYNCI1R0
—
—
—
—
—
—
SYNCI2R5 SYNCI2R4 SYNCI2R3 SYNCI2R2 SYNCI2R1 SYNCI2R0 3F3F
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-34: PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33FJ06GS101
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RPOR0
RPOR1
RPOR2
RPOR3
RPOR16
RPOR17
Legend:
06D0
06D2
06D4
06D6
06F0
06F2
—
—
—
—
—
—
—
—
—
—
—
—
RP1R5
RP3R5
RP5R5
RP7R5
RP1R4
RP3R4
RP5R4
RP7R4
RP1R3
RP3R3
RP5R3
RP7R3
RP1R2
RP3R2
RP5R2
RP7R2
RP33R2
RP35R2
RP1R1
RP3R1
RP5R1
RP7R1
RP33R1
RP35R1
RP1R0
RP3R0
RP5R0
RP7R0
RP33R0
RP35R0
—
—
—
—
—
—
—
—
—
—
—
—
RP0R5
RP2R5
RP4R5
RP6R5
RP0R4
RP2R4
RP4R4
RP6R4
RP0R3
RP2R3
RP4R3
RP6R3
RP0R2
RP2R2
RP4R2
RP6R2
RP0R1
RP2R1
RP4R1
RP6R1
RP0R0
RP2R0
RP4R0
RP6R0
0000
0000
0000
0000
0000
0000
RP33R5 RP33R4 RP33R3
RP35R5 RP35R4 RP35R3
RP32R5 RP32R4 RP32R3
RP34R5 RP34R4 RP34R3
RP32R2 RP32R1 RP32R0
RP34R2 RP34R1 RP34R0
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-35: PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33FJ06GS102, dsPIC33FJ06GS202, dsPIC33FJ16GS402
AND dsPIC33FJ16GS502
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RPOR0
RPOR1
RPOR2
RPOR3
RPOR4
RPOR5
RPOR6
RPOR7
RPOR16
RPOR17
Legend:
06D0
06D2
06D4
06D6
06D8
06DA
06DC
06DE
06F0
06F2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
RP1R5
RP3R5
RP5R5
RP7R5
RP9R5
RP1R4
RP3R4
RP5R4
RP7R4
RP9R4
RP1R3
RP3R3
RP5R3
RP7R3
RP9R3
RP1R2
RP3R2
RP5R2
RP7R2
RP9R2
RP11R2
RP13R2
RP15R2
RP33R2
RP35R2
RP1R1
RP3R1
RP5R1
RP7R1
RP9R1
RP11R1
RP13R1
RP15R1
RP33R1
RP35R1
RP1R0
RP3R0
RP5R0
RP7R0
RP9R0
RP11R0
RP13R0
RP15R0
RP33R0
RP35R0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
RP0R5
RP2R5
RP4R5
RP6R5
RP8R5
RP0R4
RP2R4
RP4R4
RP6R4
RP8R4
RP0R3
RP2R3
RP4R3
RP6R3
RP8R3
RP0R2
RP2R2
RP4R2
RP6R2
RP8R2
RP0R1 RP0R0
RP2R1 RP2R0
RP4R1 RP4R0
RP6R1 RP6R0
RP8R1 RP8R0
0000
0000
0000
0000
0000
RP11R5 RP11R4 RP11R3
RP13R5 RP13R4 RP13R3
RP15R5 RP15R4 RP15R3
RP33R5 RP33R4 RP33R3
RP35R5 RP35R4 RP35R3
RP10R5 RP10R4 RP10R3
RP12R5 RP12R4 RP12R3
RP14R5 RP14R4 RP14R3
RP32R5 RP32R4 RP32R3
RP34R5 RP34R4 RP34R3
RP10R2 RP10R1 RP10R0 0000
RP12R2 RP12R1 RP12R0 0000
RP14R2 RP14R1 RP14R0 0000
RP32R2 RP32R1 RP32R0 0000
RP34R2 RP34R1 RP34R0 0000
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-36: PERIPHERAL PIN SELECT OUTPUT REGISTER MAP FOR dsPIC33FJ16GS404 AND dsPIC33FJ16GS504
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RPOR0
RPOR1
RPOR2
RPOR3
RPOR4
RPOR5
RPOR6
RPOR7
RPOR8
RPOR9
RPOR10
RPOR11
RPOR12
RPOR13
RPOR14
RPOR16
RPOR17
Legend:
06D0
06D2
06D4
06D6
06D8
06DA
06DC
06DE
06E0
06E2
06E4
06E6
06E8
06EA
06EC
06F0
06F2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
RP1R5
RP3R5
RP5R5
RP7R5
RP9R5
RP1R4
RP3R4
RP5R4
RP7R4
RP9R4
RP1R3
RP3R3
RP5R3
RP7R3
RP9R3
RP1R2
RP3R2
RP1R1
RP3R1
RP1R0
RP3R0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
RP0R5
RP2R5
RP4R5
RP6R5
RP8R5
RP0R4
RP2R4
RP4R4
RP6R4
RP8R4
RP0R3
RP2R3
RP4R3
RP6R3
RP8R3
RP0R2
RP2R2
RP4R2
RP6R2
RP8R2
RP0R1
RP2R1
RP4R1
RP6R1
RP8R1
RP0R0
RP2R0
RP4R0
RP6R0
RP8R0
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
RP5R2
RP5R1
RP5R0
RP7R2
RP7R1
RP7R0
RP9R2
RP9R1
RP9R0
RP11R5 RP11R4 RP11R3
RP13R5 RP13R4 RP13R3
RP15R5 RP15R4 RP15R3
RP17R5 RP17R4 RP17R3
RP19R5 RP19R4 RP19R3
RP21R5 RP21R4 RP21R3
RP23R5 RP23R4 RP23R3
RP25R5 RP25R4 RP25R3
RP27R5 RP27R4 RP27R3
RP29R5 RP29R4 RP29R3
RP33R5 RP33R4 RP33R3
RP35R5 RP35R4 RP35R3
RP11R2
RP13R2
RP15R2
RP17R2
RP19R2
RP21R2
RP23R2
RP25R2
RP27R2
RP29R2
RP33R2
RP35R2
RP11R1
RP13R1
RP15R1
RP17R1
RP19R1
RP21R1
RP23R1
RP25R1
RP27R1
RP29R1
RP33R1
RP35R1
RP11R0
RP13R0
RP15R0
RP17R0
RP19R0
RP21R0
RP23R0
RP25R0
RP27R0
RP29R0
RP33R0
RP35R0
RP10R5 RP10R4 RP10R3
RP12R5 RP12R4 RP12R3
RP14R5 RP14R4 RP14R3
RP16R5 RP16R4 RP16R3
RP18R5 RP18R4 RP18R3
RP20R5 RP20R4 RP20R3
RP22R5 RP22R4 RP22R3
RP24R5 RP24R4 RP24R3
RP26R5 RP26R4 RP26R3
RP28R5 RP28R4 RP28R3
RP32R5 RP32R4 RP32R3
RP34R5 RP34R4 RP34R3
RP10R2 RP10R1 RP10R0
RP12R2 RP12R1 RP12R0
RP14R2 RP14R1 RP14R0
RP16R2 RP16R1 RP16R0
RP18R2 RP18R1 RP18R0
RP20R2 RP20R1 RP20R0
RP22R2 RP22R1 RP22R0
RP24R2 RP24R1 RP24R0
RP26R2 RP26R1 RP26R0
RP28R2 RP28R1 RP28R0
RP32R2 RP32R1 RP32R0
RP34R2 RP34R1 RP34R0
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-37: PORTA REGISTER MAP
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TRISA
PORTA
LATA
02C0
02C2
02C4
02C6
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TRISA<4:0>
RA<4:0>
LATA<4:0>
—
001F
xxxx
0000
0000
ODCA
Legend:
ODCA<4:3>
—
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-38: PORTB REGISTER MAP FOR dsPIC33FJ06GS101
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TRISB
PORTB
LATB
02C8
02CA
02CC
02CE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TRISB<7:0>
00FF
xxxx
0000
0000
RB<7:0>
LATB<7:0>
ODCB
Legend:
ODCB<7:6>
—
ODCB4
—
—
—
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-39: PORTB REGISTER MAP FOR dsPIC33FJ06GS102, dsPIC33FJ06GS202, dsPIC33FJ16GS402, dsPIC33FJ16GS404,
dsPIC33FJ16GS502 AND dsPIC33FJ16GS504
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TRISB
PORTB
LATB
02C8
02CA
02CC
02CE
TRISB<15:0>
RB<15:0>
FFFF
xxxx
0000
0000
LATB<15:0>
ODCB
ODCB<15:11>
—
—
ODCB<8:6>
—
ODCB4(1)
—
—
—
—
Legend:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
Note 1:
This bit is not available on dsPIC33FJ06GS202/502 devices.
TABLE 4-40: PORTC REGISTER MAP FOR dsPIC33FJ16GS404 AND dsPIC33FJ16GS504
SFR
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TRISC
PORTC
LATC
02D0
02D2
02D4
02D6
—
—
—
—
—
—
—
—
TRISC<13:0>
RC<13:0>
3FFF
xxxx
0000
0000
LATC<13:0>
ODCC
Legend:
ODCC<13:11>
—
—
ODCC<8:3>
—
—
ODCC0
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-41: SYSTEM CONTROL REGISTER MAP
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12 Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
RCON
0740 TRAPR IOPUWR
—
—
—
—
—
NOSC2
FRCDIV2
—
CM
NOSC1
FRCDIV1
—
VREGS
NOSC0
EXTR
SWR
SWDTEN WDTO
SLEEP
CF
IDLE
—
BOR
—
POR
OSWEN 0300(2)
xxxx(1)
OSCCON 0742
—
ROI
—
COSC2 COSC1 COSC0
CLKLOCK
IOLOCK
LOCK
—
—
CLKDIV
PLLFBD
0744
0746
DOZE2
—
DOZE1 DOZE0 DOZEN
FRCDIV0 PLLPOST1 PLLPOST0
PLLPRE4 PLLPRE3 PLLPRE2 PLLPRE1 PLLPRE0 3040
—
—
—
PLLDIV<8:0>
0030
0000
0000
2300
REFOCON 074E ROON
OSCTUN 0748
—
ROSSLP ROSEL RODIV3
RODIV2
—
RODIV1
—
RODIV0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TUN<5:0>
ACLKCON 0750 ENAPLL APLLCK SELACLK
APSTSCLR2 APSTSCLR1 APSTSCLR0 ASRCSEL FRCSEL
—
Legend:
Note 1:
2:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
The RCON register Reset values are dependent on the type of Reset.
The OSCCON register Reset values are dependent on the FOSCx Configuration bits and on type of Reset.
TABLE 4-42: NVM REGISTER MAP
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
NVMCON
NVMKEY
0760
0766
WR
—
WREN
—
WRERR
—
—
—
—
—
—
—
—
—
—
—
—
ERASE
—
—
NVMOP3 NVMOP2 NVMOP1 NVMOP0 0000(1)
NVMKEY<7:0>
0000
Legend:
Note 1:
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
Reset value shown is for POR only. The value on other Reset states is dependent on the state of memory write or erase operations at the time of Reset.
TABLE 4-43: PMD REGISTER MAP FOR dsPIC33FJ06GS101 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PMD1
0770
0772
0774
0776
077A
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
T2MD
—
T1MD
—
—
PWMMD
IC2MD
—
—
IC1MD
—
I2C1MD
—
—
—
—
—
U1MD
—
—
—
—
—
—
SPI1MD
—
—
—
—
—
—
ADCMD 0000
PMD2
PMD3
PMD4
PMD6
Legend:
—
—
—
—
—
—
—
—
OC2MD OC1MD 0000
—
CMPMD
—
—
—
—
—
—
—
—
0000
0000
0000
—
—
—
—
—
REFOMD
—
—
PWM4MD
—
—
PWM1MD
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-44: PMD REGISTER MAP FOR dsPIC33FJ06GS102 DEVICES ONLY
File
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PMD1
0770
0772
0774
0776
077A
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
T2MD
—
T1MD
—
—
—
PWMMD
IC2MD
—
—
IC1MD
—
I2C1MD
—
—
—
—
—
U1MD
—
—
—
—
—
—
SPI1MD
—
—
—
—
—
—
ADCMD 0000
PMD2
PMD3
PMD4
PMD6
Legend:
—
—
—
—
—
—
OC2MD OC1MD 0000
—
—
CMPMD
—
—
—
—
—
—
—
—
0000
0000
0000
—
—
—
—
—
REFOMD
—
—
—
—
PWM2MD PWM1MD
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-45: PMD REGISTER MAP FOR dsPIC33FJ06GS202 DEVICES ONLY
SFR
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PMD1
0770
0772
0774
0776
077A
077C
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
T2MD
—
T1MD
—
—
—
PWMMD
—
IC1MD
—
I2C1MD
—
—
—
—
—
—
U1MD
—
—
—
—
—
—
—
SPI1MD
—
—
—
—
—
—
—
—
—
—
—
—
ADCMD 0000
OC1MD 0000
PMD2
PMD3
PMD4
PMD6
PMD7
Legend:
—
—
—
—
—
—
—
—
—
—
—
CMPMD
—
—
—
REFOMD
—
—
—
—
—
0000
0000
0000
0000
—
—
—
—
—
—
—
PWM2MD PWM1MD
CMP2MD CMP1MD
—
—
—
—
—
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-46: PMD REGISTER MAP FOR dsPIC33FJ16GS402 AND dsPIC33FJ16GS404 DEVICES ONLY
SFR
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PMD1
0770
0772
0774
0776
077A
077C
—
—
—
—
—
—
—
—
—
—
—
—
T3MD
—
T2MD
—
T1MD
—
—
—
—
—
PWMMD
IC2MD
—
—
IC1MD
—
I2C1MD
—
—
—
—
—
—
U1MD
—
—
—
—
—
—
—
SPI1MD
—
—
—
—
—
—
—
ADCMD 0000
PMD2
PMD3
PMD4
PMD6
PMD7
Legend:
—
—
—
—
—
—
OC2MD OC1MD 0000
—
—
—
—
—
REFOMD
—
—
—
—
—
—
—
—
—
0000
0000
0000
0000
—
—
—
—
—
—
—
—
—
PWM3MD PWM2MD PWM1MD
—
—
—
—
—
—
—
—
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
TABLE 4-47: PMD REGISTER MAP FOR dsPIC33FJ16GS502 AND dsPIC33FJ16GS504 DEVICES ONLY
SFR
Name
SFR
Addr
All
Resets
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PMD1
0770
0772
0774
0776
077A
077C
—
—
—
—
—
—
—
—
—
—
—
—
T3MD
—
T2MD
—
T1MD
—
—
—
PWMMD
IC2MD
—
—
IC1MD
—
I2C1MD
—
—
—
—
—
—
U1MD
—
—
—
—
—
—
—
SPI1MD
—
—
—
—
—
—
—
ADCMD 0000
PMD2
PMD3
PMD4
PMD6
PMD7
Legend:
—
—
—
—
—
—
OC2MD OC1MD 0000
—
—
—
CMPMD
—
—
—
REFOMD
—
—
—
—
—
—
—
—
—
0000
0000
0000
0000
—
—
—
—
—
—
—
—
PWM4MD PWM3MD PWM2MD PWM1MD
CMP4MD CMP3MD CMP2MD CMP1MD
—
—
—
—
—
x= unknown value on Reset, — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
4.2.6
SOFTWARE STACK
4.3
Instruction Addressing Modes
In addition to its use as a Working register, the W15
register in the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 devices is also used as a
software Stack Pointer. The Stack Pointer always
points to the first available free word and grows from
lower to higher addresses. It predecrements for stack
pops and post-increments for stack pushes, as shown
in Figure 4-6. For a PC push during any CALLinstruc-
tion, the MSb of the PC is zero-extended before the
push, ensuring that the MSb is always clear.
The addressing modes shown in Table 4-48 form the
basis of the addressing modes optimized to support the
specific features of individual instructions. The
addressing modes provided in the MAC class of
instructions differ from those in the other instruction
types.
4.3.1
FILE REGISTER INSTRUCTIONS
Most file register instructions use a 13-bit address field
(f) to directly address data present in the first
8192 bytes of data memory (Near Data Space). Most
file register instructions employ a Working register, W0,
which is denoted as WREG in these instructions. The
destination is typically either the same file register or
WREG (with the exception of the MUL instruction),
which writes the result to a register or register pair. The
MOV instruction allows additional flexibility and can
access the entire data space.
Note:
A PC push during exception processing
concatenates the SRL register to the MSb
of the PC prior to the push.
The Stack Pointer Limit register (SPLIM) associated
with the Stack Pointer sets an upper address boundary
for the stack. SPLIM is uninitialized at Reset. As is the
case for the Stack Pointer, SPLIM<0> is forced to ‘0’
because all stack operations must be word-aligned.
4.3.2
MCU INSTRUCTIONS
Whenever an EA is generated using W15 as a source
or destination pointer, the resulting address is
compared with the value in SPLIM. If the contents of
the Stack Pointer (W15) and the SPLIM register are
equal and a push operation is performed, a stack error
trap will not occur. The stack error trap will occur on a
subsequent push operation. For example, to cause a
stack error trap when the stack grows beyond address
0x1000 in RAM, initialize the SPLIM with the value
0x0FFE.
The three-operand MCU instructions are of the form:
Operand 3 = Operand 1 <function> Operand 2
where, Operand 1is always a Working register (that is,
the addressing mode can only be register direct), which
is referred to as Wb. Operand 2 can be a W register,
fetched from data memory, or a 5-bit literal. The result
location can be either a W register or a data memory
location. The following addressing modes are
supported by MCU instructions:
Similarly, a Stack Pointer underflow (stack error) trap is
generated when the Stack Pointer address is found to
be less than 0x0800. This prevents the stack from
interfering with the Special Function Register (SFR)
space.
• Register Direct
• Register Indirect
• Register Indirect Post-Modified
• Register Indirect Pre-Modified
• 5-bit or 10-bit Literal
A write to the SPLIM register should not be immediately
followed by an indirect read operation using W15.
Note:
Not all instructions support all the
addressing modes given above. Individ-
ual instructions can support different
subsets of these addressing modes.
FIGURE 4-6:
CALL STACK FRAME
0x0000
15
0
PC<15:0>
000000000
W15 (before CALL)
PC<22:16>
<Free Word>
W15 (after CALL)
POP : [--W15]
PUSH: [W15++]
2008-2014 Microchip Technology Inc.
DS70000318G-page 73
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 4-48: FUNDAMENTAL ADDRESSING MODES SUPPORTED
Addressing Mode
File Register Direct
Description
The address of the file register is specified explicitly.
The contents of a register are accessed directly.
The contents of Wn forms the Effective Address (EA).
Register Direct
Register Indirect
Register Indirect Post-Modified
The contents of Wn forms the EA. Wn is post-modified (incremented or
decremented) by a constant value.
Register Indirect Pre-Modified
Wn is pre-modified (incremented or decremented) by a signed constant value
to form the EA.
Register Indirect with Register Offset The sum of Wn and Wb forms the EA.
(Register Indexed)
Register Indirect with Literal Offset
The sum of Wn and a literal forms the EA.
4.3.3
MOVE AND ACCUMULATOR
INSTRUCTIONS
4.3.4
MACINSTRUCTIONS
The dual source operand DSP instructions (CLR, ED,
EDAC, MAC, MPY, MPY.N, MOVSACand MSC), also referred
to as MACinstructions, use a simplified set of addressing
modes to allow the user application to effectively
manipulate the Data Pointers through register indirect
tables.
Move instructions and the DSP accumulator class of
instructions to provide a greater addressing flexibility
than other instructions. In addition to the addressing
modes supported by most MCU instructions, move and
accumulator instructions also support Register Indirect
with Register Offset Addressing mode, also referred to
as Register Indexed mode.
The two-source operand prefetch registers must be
members of the set {W8, W9, W10, W11}. For data
reads, W8 and W9 are always directed to the X RAGU,
and W10 and W11 are always directed to the Y AGU.
The Effective Addresses generated (before and after
modification) must, therefore, be valid addresses within
X data space for W8 and W9 and Y data space for W10
and W11.
Note:
For the MOV instructions, the addressing
mode specified in the instruction can differ
for the source and destination EA. How-
ever, the 4-bit Wb (register offset) field is
shared by both source and destination
(but typically only used by one).
Note:
Register Indirect with Register Offset
Addressing mode is available only for W9
(in X space) and W11 (in Y space).
In summary, the following addressing modes are
supported by move and accumulator instructions:
• Register Direct
In summary, the following addressing modes are
• Register Indirect
supported by the MACclass of instructions:
• Register Indirect Post-modified
• Register Indirect Pre-modified
• Register Indirect with Register Offset (Indexed)
• Register Indirect with Literal Offset
• 8-bit Literal
• Register Indirect
• Register Indirect Post-Modified by 2
• Register Indirect Post-Modified by 4
• Register Indirect Post-Modified by 6
• Register Indirect with Register Offset (Indexed)
• 16-bit Literal
Note:
Not all instructions support all the
addressing modes given above. Individual
instructions may support different subsets
of these addressing modes.
4.3.5
OTHER INSTRUCTIONS
Besides the addressing modes outlined previously, some
instructions use literal constants of various sizes. For
example, BRA (branch) instructions use 16-bit signed
literals to specify the branch destination directly, whereas
the DISIinstruction uses a 14-bit unsigned literal field. In
some instructions, such as ADD Acc, the source of an
operand or result is implied by the opcode itself. Certain
operations, such as NOP, do not have any operands.
DS70000318G-page 74
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
4.4
Modulo Addressing
Note:
Y space Modulo Addressing EA calcula-
tions assume word-sized data (LSb of
every EA is always clear).
Modulo Addressing mode is a method used to provide
an automated means to support circular data buffers
using hardware. The objective is to remove the need
for software to perform data address boundary checks
when executing tightly looped code, as is typical in
many DSP algorithms.
The length of a circular buffer is not directly specified. It
is determined by the difference between the
corresponding start and end addresses. The maximum
possible length of the circular buffer is 32K words
(64 Kbytes).
Modulo Addressing can operate in either data or program
space (since the Data Pointer mechanism is essentially
the same for both). One circular buffer can be supported
in each of the X (which also provides the pointers into
program space) and Y data spaces. Modulo Addressing
can operate on any W register Pointer. However, it is not
advisable to use W14 or W15 for Modulo Addressing
since these two registers are used as the Stack Frame
Pointer and Stack Pointer, respectively.
4.4.2
W ADDRESS REGISTER
SELECTION
The Modulo and Bit-Reversed Addressing Control
register, MODCON<15:0>, contains enable flags as
well as a W register field to specify the W Address
registers. The XWM and YWM fields select the
registers that will operate with Modulo Addressing:
In general, any particular circular buffer can be
configured to operate in only one direction as there are
certain restrictions on the buffer start address (for incre-
menting buffers), or end address (for decrementing
buffers), based upon the direction of the buffer.
• If XWM = 15, X RAGU and X WAGU Modulo
Addressing is disabled.
• If YWM = 15, Y AGU Modulo Addressing is
disabled.
The X Address Space Pointer W register (XWM), to
which Modulo Addressing is to be applied, is stored in
MODCON<3:0> (see Table 4-1). Modulo Addressing is
enabled for X data space when XWM is set to any value
other than ‘15’ and the XMODEN bit is set at
MODCON<15>.
The only exception to the usage restrictions is for
buffers that have a power-of-two length. As these
buffers satisfy the start and end address criteria, they
can operate in a bidirectional mode (that is, address
boundary checks are performed on both the lower and
upper address boundaries).
The Y Address Space Pointer W register (YWM) to
which Modulo Addressing is to be applied is stored in
MODCON<7:4>. Modulo Addressing is enabled for Y
data space when YWM is set to any value other than
‘15’ and the YMODEN bit is set at MODCON<14>.
4.4.1
START AND END ADDRESS
The Modulo Addressing scheme requires that a
starting and ending address be specified and loaded
into the 16-bit Modulo Buffer Address registers:
XMODSRT, XMODEND, YMODSRT and YMODEND
(see Table 4-1).
FIGURE 4-7:
MODULO ADDRESSING OPERATION EXAMPLE
MOV
MOV
MOV
MOV
MOV
MOV
#0x1100, W0
Byte
Address
W0, XMODSRT
#0x1163, W0
W0, MODEND
#0x8001, W0
W0, MODCON
;set modulo start address
;set modulo end address
;enable W1, X AGU for modulo
;W0 holds buffer fill value
;point W1 to buffer
0x1100
MOV
MOV
#0x0000, W0
#0x1110, W1
DO
MOV
AGAIN, #0x31
W0, [W1++]
;fill the 50 buffer locations
;fill the next location
0x1163
AGAIN: INC W0, W0
;increment the fill value
Start Addr = 0x1100
End Addr = 0x1163
Length = 0x0032 words
2008-2014 Microchip Technology Inc.
DS70000318G-page 75
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
If the length of a bit-reversed buffer is M = 2N bytes,
the last ‘N’ bits of the data buffer start address must
be zeros.
4.4.3
MODULO ADDRESSING
APPLICABILITY
Modulo Addressing can be applied to the Effective
Address (EA) calculation associated with any W
register. Address boundaries check for addresses
equal to:
XB<14:0> is the Bit-Reversed Address modifier, or
‘pivot point,’ which is typically a constant. In the case of
an FFT computation, its value is equal to half of the FFT
data buffer size.
• The upper boundary addresses for incrementing
buffers
Note:
All bit-reversed EA calculations assume
word-sized data (LSb of every EA is
always clear). The XB value is scaled
accordingly to generate compatible (byte)
addresses.
• The lower boundary addresses for decrementing
buffers
The address boundaries check for addresses less than
or greater than the upper (for incrementing buffers) and
lower (for decrementing buffers) boundary addresses
(not just equal to). Address changes can, therefore,
jump beyond boundaries and still be adjusted correctly.
When enabled, Bit-Reversed Addressing is executed
only for Register Indirect with Pre-Increment or Post-
Increment Addressing and word-sized data writes. It
will not function for any other addressing mode or for
byte-sized data, and normal addresses are generated
instead. When Bit-Reversed Addressing is active, the
W Address Pointer is always added to the address
modifier (XB), and the offset associated with the Regis-
ter Indirect Addressing mode is ignored. In addition, as
word-sized data is a requirement, the LSb of the EA is
ignored (and always clear).
Note:
The modulo corrected Effective Address is
written back to the register only when Pre-
Modify or Post-Modify Addressing mode is
used to compute the Effective Address.
When an address offset (such as
[W7 + W2]) is used, Modulo Addressing
correction is performed but the contents of
the register remain unchanged.
Note:
Modulo Addressing and Bit-Reversed
Addressing should not be enabled
together. If an application attempts to do
so, Bit-Reversed Addressing will assume
priority when active for the X WAGU and X
WAGU; Modulo Addressing will be dis-
abled. However, Modulo Addressing will
continue to function in the X RAGU.
4.5
Bit-Reversed Addressing
Bit-Reversed Addressing mode is intended to simplify
data re-ordering for radix-2 FFT algorithms. It is
supported by the X AGU for data writes only.
The modifier, which can be a constant value or register
contents, is regarded as having its bit order reversed. The
address source and destination are kept in normal order.
Thus, the only operand requiring reversal is the modifier.
If Bit-Reversed Addressing has already been enabled
by setting the BREN (XBREV<15>) bit, a write to the
XBREV register should not be immediately followed by
an indirect read operation using the W register that has
been designated as the Bit-Reversed Pointer.
4.5.1
BIT-REVERSED ADDRESSING
IMPLEMENTATION
Bit-Reversed Addressing mode is enabled in any of
these situations:
• BWM bits (W register selection) in the MODCON
register are any value other than 15 (the stack
cannot be accessed using Bit-Reversed
Addressing)
• The BREN bit is set in the XBREV register
• The addressing mode used is Register Indirect
with Pre-Increment or Post-Increment
DS70000318G-page 76
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 4-8:
BIT-REVERSED ADDRESS EXAMPLE
Sequential Address
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b1 b2 b3 b4
0
Bit Locations Swapped Left-to-Right
Around Center of Binary Value
0
Bit-Reversed Address
Pivot Point
XB = 0x0008 for a 16-Word Bit-Reversed Buffer
TABLE 4-49: BIT-REVERSED ADDRESS SEQUENCE (16-ENTRY)
Normal Address Bit-Reversed Address
A3
A2
A1
A0
Decimal
A3
A2
A1
A0
Decimal
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
8
2
4
3
12
2
4
5
10
6
6
7
14
1
8
9
9
10
11
12
13
14
15
5
13
3
11
7
15
2008-2014 Microchip Technology Inc.
DS70000318G-page 77
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
4.6.1
ADDRESSING PROGRAM SPACE
4.6
Interfacing Program and Data
Memory Spaces
Since the address ranges for the data and program
spaces are 16 and 24 bits, respectively, a method is
needed to create a 23-bit or 24-bit program address
from 16-bit data registers. The solution depends on the
interface method to be used.
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 architecture uses a 24-bit-wide program space and a
16-bit-wide data space. The architecture is also a
modified Harvard scheme, meaning that data can also be
present in the program space. To use this data
successfully, it must be accessed in a way that preserves
the alignment of information in both spaces.
For table operations, the 8-bit Table Page register
(TBLPAG) is used to define a 32K word region within
the program space. This is concatenated with a 16-bit
EA to arrive at a full 24-bit program space address. In
this format, the Most Significant bit of TBLPAG is used
to determine if the operation occurs in the user memory
(TBLPAG<7> = 0) or the configuration memory
(TBLPAG<7> = 1).
Aside from normal execution, the dsPIC33FJ06GS101/
X02 and dsPIC33FJ16GSX02/X04 architecture
provides two methods by which program space can be
accessed during operation:
• Using table instructions to access individual bytes
or words anywhere in the program space
For remapping operations, the 8-bit Program Space
Visibility register (PSVPAG) is used to define a
16K word page in the program space. When the Most
Significant bit of the EA is ‘1’, PSVPAG is concatenated
with the lower 15 bits of the EA to form a 23-bit program
space address. Unlike table operations, this limits
remapping operations strictly to the user memory area.
• Remapping a portion of the program space into
the data space (Program Space Visibility)
Table instructions allow an application to read or write
to small areas of the program memory. This capability
makes the method ideal for accessing data tables that
need to be updated periodically. It also allows access
to all bytes of the program word. The remapping
method allows an application to access a large block of
data on a read-only basis, which is ideal for look ups
from a large table of static data. The application can
only access the least significant word of the program
word.
Table 4-50 and Figure 4-9 show how the program EA is
created for table operations and remapping accesses
from the data EA. Here, P<23:0> refers to a program
space word, and D<15:0> refers to a data space word.
TABLE 4-50: PROGRAM SPACE ADDRESS CONSTRUCTION
Program Space Address
Access
Space
Access Type
<23>
<22:16>
<15>
<14:1>
<0>
Instruction Access
(Code Execution)
User
User
0
PC<22:1>
0
0xx xxxx xxxx xxxx xxxx xxx0
TBLRD/TBLWT
(Byte/Word Read/Write)
TBLPAG<7:0>
0xxx xxxx
Data EA<15:0>
xxxx xxxx xxxx xxxx
Data EA<15:0>
Configuration
TBLPAG<7:0>
1xxx xxxx
xxxx xxxx xxxx xxxx
Program Space Visibility User
(Block Remap/Read)
0
0
PSVPAG<7:0>
xxxx xxxx
Data EA<14:0>(1)
xxx xxxx xxxx xxxx
Note 1: Data EA<15> is always ‘1’ in this case, but is not used in calculating the program space address. Bit 15 of
the address is PSVPAG<0>.
DS70000318G-page 78
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 4-9:
DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION
Program Counter(1)
Program Counter
23 Bits
0
0
1/0
EA
Table Operations(2)
1/0
TBLPAG
8 Bits
16 Bits
24 Bits
Select
1
0
EA
Program Space Visibility(1)
(Remapping)
0
PSVPAG
8 Bits
15 Bits
23 Bits
Byte Select
User/Configuration
Space Select
Note 1: The Least Significant bit (LSb) of program space addresses is always fixed as ‘0’ to
maintain word alignment of data in the program and data spaces.
2: Table operations are not required to be word-aligned. Table Read operations are permitted
in the configuration memory space.
2008-2014 Microchip Technology Inc.
DS70000318G-page 79
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
- In Byte mode, either the upper or lower byte
of the lower program word is mapped to the
lower byte of a data address. The upper byte
is selected when byte select is ‘1’; the lower
byte is selected when it is ‘0’.
4.6.2
DATA ACCESS FROM PROGRAM
MEMORY USING TABLE
INSTRUCTIONS
The TBLRDL and TBLWTL instructions offer a direct
method of reading or writing the lower word of any
address within the program space without going
through data space. The TBLRDH and TBLWTH
instructions are the only method to read or write the
upper 8 bits of a program space word as data.
• TBLRDH (Table Read High):
- In Word mode, this instruction maps the entire
upper word of a program address (P<23:16>)
to a data address. Note that D<15:8>, the
‘phantom byte’, will always be ‘0’.
The PC is incremented by two for each successive
24-bit program word. This allows program memory
addresses to directly map to data space addresses.
Program memory can thus be regarded as two 16-bit
wide word address spaces, residing side by side, each
with the same address range. TBLRDL and TBLWTL
access the space that contains the least significant
data word. TBLRDHand TBLWTHaccess the space that
contains the upper data byte.
- In Byte mode, this instruction maps the upper
or lower byte of the program word to D<7:0> of
the data address, in the TBLRDLinstruction.
The data is always ‘0’ when the upper
‘phantom’ byte is selected (Byte Select = 1).
Similarly, two table instructions, TBLWTHand TBLWTL,
are used to write individual bytes or words to a program
space address. The details of their operation are
explained in Section 5.0 “Flash Program Memory”.
Two table instructions are provided to move byte or
word-sized (16-bit) data to and from program space.
Both function as either byte or word operations.
For all table operations, the area of program memory
space to be accessed is determined by the Table Page
register (TBLPAG). TBLPAG covers the entire program
memory space of the device, including user and con-
figuration spaces. When TBLPAG<7> = 0, the table
page is located in the user memory space. When
TBLPAG<7> = 1, the page is located in configuration
space.
• TBLRDL(Table Read Low):
- In Word mode, this instruction maps the
lower word of the program space location
(P<15:0>) to a data address (D<15:0>).
FIGURE 4-10:
ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS
Program Space
TBLPAG
02
23
15
0
0x000000
23
16
8
0
00000000
00000000
00000000
0x020000
0x030000
00000000
‘Phantom’ Byte
TBLRDH.B (Wn<0> = 0)
TBLRDL.B (Wn<0> = 1)
TBLRDL.B (Wn<0> = 0)
TBLRDL.W
The address for the table operation is determined by the data EA
within the page defined by the TBLPAG register.
Only read operations are shown; write operations are also valid in
the user memory area.
0x800000
DS70000318G-page 80
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
24-bit program word are used to contain the data. The
upper 8 bits of any program space location used as
data should be programmed with ‘1111 1111’ or
‘0000 0000’ to force a NOP. This prevents possible
issues should the area of code ever be accidentally
executed.
4.6.3
READING DATA FROM PROGRAM
MEMORY USING PROGRAM SPACE
VISIBILITY
The upper 32 Kbytes of data space may optionally be
mapped into any 16K word page of the program space.
This option provides transparent access to stored
constant data from the data space without the need to
use special instructions (such as TBLRDL/H).
Note:
PSV access is temporarily disabled during
Table Reads/Writes.
Program space access through the data space occurs
if the Most Significant bit of the data space EA is ‘1’ and
Program Space Visibility (PSV) is enabled by setting
the PSV bit in the Core Control register
(CORCON<2>). The location of the program memory
space to be mapped into the data space is determined
by the Program Space Visibility Page register
(PSVPAG). This 8-bit register defines any one of 256
possible pages of 16K words in program space. In
effect, PSVPAG functions as the upper 8 bits of the
program memory address, with the 15 bits of the EA
functioning as the lower bits. By incrementing the PC
by 2 for each program memory word, the lower 15 bits
of data space addresses directly map to the lower
15 bits in the corresponding program space addresses.
For operations that use PSV and are executed outside
aREPEATloop, theMOVand MOV.Dinstructions require
one instruction cycle in addition to the specified
execution time. All other instructions require two
instruction cycles in addition to the specified execution
time.
For operations that use PSV, and are executed inside
a REPEATloop, these instances require two instruction
cycles in addition to the specified execution time of the
instruction:
• Execution in the first iteration
• Execution in the last iteration
• Execution prior to exiting the loop due to an
interrupt
Data reads to this area add a cycle to the instruction
being executed, since two program memory fetches
are required.
• Execution upon re-entering the loop after an
interrupt is serviced
Any other iteration of the REPEAT loop will allow the
instruction using PSV to access data, to execute in a
single cycle.
Although each data space address 8000h and higher
maps directly into a corresponding program memory
address (see Figure 4-11), only the lower 16 bits of the
FIGURE 4-11:
PROGRAM SPACE VISIBILITY OPERATION
When CORCON<2> = 1and EA<15> = 1:
Program Space
Data Space
PSVPAG
02
23
15
0
0x000000
0x0000
Data EA<14:0>
0x010000
0x018000
The data in the page
designated by
PSVPAG is mapped
into the upper half of
the data memory
space...
0x8000
PSV Area
...while the lower 15 bits
of the EA specify an
exact address within
the PSV area. This
corresponds exactly to
the same lower 15 bits
of the actual program
space address.
0xFFFF
0x800000
2008-2014 Microchip Technology Inc.
DS70000318G-page 81
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 82
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
power (VDD), ground (VSS) and Master Clear (MCLR).
5.0
FLASH PROGRAM MEMORY
This allows customers to manufacture boards with
unprogrammed devices and then program the Digital
Signal Controller just before shipping the product. This
also allows the most recent firmware or a custom
firmware to be programmed.
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “Flash Programming”
(DS70191) in the “dsPIC33F/PIC24H
Family Reference Manual”, which is avail-
able from the Microchip web site
(www.microchip.com).
RTSP is accomplished using TBLRD(Table Read) and
TBLWT(Table Write) instructions. With RTSP, the user
application can write program memory data, either in
blocks or ‘rows’ of 64 instructions (192 bytes) at a time,
or a single program memory word, and erase program
memory in blocks or ‘pages’ of 512 instructions
(1536 bytes) at a time.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
5.1
Table Instructions and Flash
Programming
Regardless of the method used, all programming of
Flash memory is done with the Table Read and Table
Write instructions. These allow direct read and write
access to the program memory space from the data
memory while the device is in normal operating mode.
The 24-bit target address in the program memory is
formed using bits<7:0> of the TBLPAG register and the
Effective Address (EA) from a W register specified in
the table instruction, as shown in Figure 5-1.
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices contain internal Flash program memory for
storing and executing application code. The memory is
readable, writable and erasable during normal operation
over the entire VDD range.
Flash memory can be programmed in two ways:
The TBLRDLand the TBLWTLinstructions are used to
read or write to bits<15:0> of program memory.
TBLRDLand TBLWTLcan access program memory in
both Word and Byte modes.
• In-Circuit Serial Programming™ (ICSP™)
programming capability
• Run-Time Self-Programming (RTSP)
ICSP allows
a
dsPIC33FJ06GS101/X02 and
The TBLRDHand TBLWTHinstructions are used to read
or write to bits<23:16> of program memory. TBLRDH
and TBLWTHcan also access program memory in Word
or Byte mode.
dsPIC33FJ16GSX02/X04 device to be serially
programmed while in the end application circuit. This is
done with two lines for programming clock and
programming data (one of the alternate programming
pin pairs: PGECx/PGEDx, and three other lines for
FIGURE 5-1:
ADDRESSING FOR TABLE REGISTERS
24 Bits
Program Counter
Using
Program Counter
0
0
Working Reg EA
Using
Table Instruction
1/0
TBLPAG Reg
8 Bits
16 Bits
User/Configuration
Space Select
Byte
Select
24-Bit EA
2008-2014 Microchip Technology Inc.
DS70000318G-page 83
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
For example, if the device is operating at +125°C, the
5.2
RTSP Operation
FRC accuracy will be ±5%. If the TUN<5:0> bits (see
Register 8-4) are set to ‘b111111, the minimum row
write time is equal to Equation 5-2.
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 Flash program memory array is organized into rows
of 64 instructions or 192 bytes. RTSP allows the user
application to erase a page of memory, which consists of
eight rows (512 instructions) at a time, and to program
one row or one word at a time. Table 24-12 shows typical
erase and programming times. The 8-row erase pages
and single row write rows are edge-aligned from the
beginning of program memory, on boundaries of
1536 bytes and 192 bytes, respectively.
EQUATION 5-2:
MINIMUM ROW WRITE
TIME
11064 Cycles
7.37 MHz 1 + 0.05 1 – 0.00375
----------------------------------------------------------------------------------------------
= 1.435ms
TRW
=
The program memory implements holding buffers that
can contain 64 instructions of programming data. Prior
to the actual programming operation, the write data
must be loaded into the buffers sequentially. The
instruction words loaded must always be from a group
of 64 boundary.
The maximum row write time is equal to Equation 5-3.
EQUATION 5-3:
MAXIMUM ROW WRITE
TIME
11064 Cycles
---------------------------------------------------------------------------------------------
= 1.586ms
TRW
=
7.37 MHz 1 – 0.05 1 – 0.00375
The basic sequence for RTSP programming is to set up
a Table Pointer, then do a series of TBLWTinstructions
to load the buffers. Programming is performed by
setting the control bits in the NVMCON register. A total
of 64 TBLWTL and TBLWTH instructions are required
to load the instructions.
Setting the WR bit (NVMCON<15>) starts the opera-
tion, and the WR bit is automatically cleared when the
operation is finished.
All of the Table Write operations are single-word writes
(two instruction cycles) because only the buffers are
5.4
Control Registers
written.
programming each row.
A
programming cycle is required for
Two SFRs are used to read and write the program
Flash memory: NVMCON and NVMKEY.
The NVMCON register (Register 5-1) controls which
blocks are to be erased, which memory type is to be
programmed and the start of the programming cycle.
5.3
Programming Operations
A complete programming sequence is necessary for
programming or erasing the internal Flash in RTSP
mode. The processor stalls (waits) until the
programming operation is finished.
NVMKEY is a write-only register that is used for write
protection. To start a programming or erase sequence,
the user application must consecutively write 0x55 and
0xAA to the NVMKEY register. Refer to Section 5.3
“Programming Operations” for further details.
The programming time depends on the FRC accuracy
(see Table 24-20) and the value of the FRC Oscillator
Tuning register (see Register 8-4). Use the following
formula to calculate the minimum and maximum values
for the Row Write Time, Page Erase Time, and Word
Write Cycle Time parameters (see Table 24-12).
EQUATION 5-1:
PROGRAMMING TIME
T
-------------------------------------------------------------------------------------------------------------------------
7.37 MHz FRC Accuracy% FRC Tuning%
DS70000318G-page 84
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 5-1:
NVMCON: FLASH MEMORY CONTROL REGISTER
R/SO-0(1)
WR
R/W-0(1)
WREN
R/W-0(1)
WRERR
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
R/W-0(1)
ERASE
U-0
—
U-0
—
R/W-0(1)
NVMOP3(2) NVMOP2(2)
R/W-0(1)
R/W-0(1)
NVMOP1(2) NVMOP0(2)
R/W-0(1)
bit 7
bit 0
Legend:
SO = Settable Only bit
W = Writable bit
‘1’ = Bit is set
R = Readable bit
-n = Value at POR
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
WR: Write Control bit(1)
1= Initiates a Flash memory program or erase operation; the operation is self-timed and the bit is
cleared by hardware once the operation is complete
0= Program or erase operation is complete and inactive
bit 14
bit 13
WREN: Write Enable bit(1)
1= Enable Flash program/erase operations
0= Inhibit Flash program/erase operations
WRERR: Write Sequence Error Flag bit(1)
1= An improper program or erase sequence attempt, or termination has occurred (bit is set
automatically on any set attempt of the WR bit)
0= The program or erase operation completed normally
bit 12-7
bit 6
Unimplemented: Read as ‘0’
ERASE: Erase/Program Enable bit(1)
1= Performs the erase operation specified by NVMOP<3:0> on the next WR command
0= Performs the program operation specified by NVMOP<3:0> on the next WR command
bit 5-4
bit 3-0
Unimplemented: Read as ‘0’
NVMOP<3:0>: NVM Operation Select bits(1,2)
If ERASE = 1:
1111= Memory bulk erase operation
1101= Erase general segment
0011= No operation
0010= Memory page erase operation
0001= No operation
0000= Erase a single Configuration register byte
If ERASE = 0:
1111= No operation
1101= No operation
0011= Memory word program operation
0010= No operation
0001= Memory row program operation
0000= Program a single Configuration register byte
Note 1: These bits can only be Reset on POR.
2: All other combinations of NVMOP<3:0> are unimplemented.
2008-2014 Microchip Technology Inc.
DS70000318G-page 85
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 5-2:
NVMKEY: NONVOLATILE MEMORY KEY REGISTER
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
bit 0
W-0
bit 7
W-0
W-0
W-0
W-0
W-0
W-0
W-0
NVMKEY<7:0>
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-8
bit 7-0
Unimplemented: Read as ‘0’
NVMKEY<7:0>: Nonvolatile Memory Key bits (write-only)
DS70000318G-page 86
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
4. Write the first 64 instructions from data RAM into
the program memory buffers (see Example 5-2).
5.4.1
PROGRAMMING ALGORITHM FOR
FLASH PROGRAM MEMORY
5. Write the program block to Flash memory:
One row of program Flash memory can be
programmed at a time. To achieve this, it is necessary
to erase the 8-row erase page that contains the desired
row. The general process is:
a) Set the NVMOP<3:0> bits to ‘0001’ to
configure for row programming. Clear the
ERASE bit and set the WREN bit.
b) Write 0x55 to the NVMKEY register.
c) Write 0xAA to the NVMKEY register.
1. Read eight rows of program memory
(512 instructions) and store in data RAM.
d) Set the WR bit. The programming cycle begins
and the CPU stalls for the duration of the write
cycle. When the write to Flash memory is done,
the WR bit is cleared automatically.
2. Update the program data in RAM with the desired
new data.
3. Erase the block (see Example 5-1):
a) Set the NVMOP<3:0> bits (NVMCON<3:0>) to
‘0010’ to configure for block erase. Set
the ERASE (NVMCON<6>) and WREN
(NVMCON<14>) bits.
6. Repeat Steps 4 and 5, using the next available
64 instructions from the block in data RAM by incre-
menting the value in the TBLPAG register, until all
512 instructions are written back to Flash memory.
b) Write the starting address of the page to be
erased into the TBLPAG and W registers.
For protection against accidental operations, the write
initiate sequence for the NVMKEY register must be
used to allow any erase or program operation to
proceed. After the programming command has been
executed, the user application must wait for the pro-
gramming time until programming is complete. The two
instructions following the start of the programming
sequence should be NOPs, as shown in Example 5-3.
c) Write 0x55 to NVMKEY.
d) Write 0xAA to NVMKEY.
e) Set the WR bit (NVMCON<15>). The erase
cycle begins and the CPU stalls for the duration
of the erase cycle. When the erase is done, the
WR bit is cleared automatically.
EXAMPLE 5-1:
ERASING A PROGRAM MEMORY PAGE
; Set up NVMCON for block erase operation
MOV
MOV
#0x4042, W0
W0, NVMCON
;
; Initialize NVMCON
; Init pointer to row to be ERASED
MOV
MOV
MOV
#tblpage(PROG_ADDR), W0
W0, TBLPAG
#tbloffset(PROG_ADDR), W0
;
; Initialize PM Page Boundary SFR
; Initialize in-page EA[15:0] pointer
; Set base address of erase block
; Block all interrupts with priority <7
; for next 5 instructions
TBLWTL W0, [W0]
DISI
#5
MOV
MOV
MOV
MOV
BSET
NOP
NOP
#0x55, W0
W0, NVMKEY
#0xAA, W1
W1, NVMKEY
NVMCON, #WR
; Write the 55 key
;
; Write the AA key
; Start the erase sequence
; Insert two NOPs after the erase
; command is asserted
2008-2014 Microchip Technology Inc.
DS70000318G-page 87
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
EXAMPLE 5-2:
LOADING THE WRITE BUFFERS
; Set up NVMCON for row programming operations
MOV
MOV
#0x4001, W0
W0, NVMCON
;
; Initialize NVMCON
; Set up a pointer to the first program memory location to be written
; program memory selected, and writes enabled
MOV
MOV
MOV
#0x0000, W0
W0, TBLPAG
#0x6000, W0
;
; Initialize PM Page Boundary SFR
; An example program memory address
; Perform the TBLWT instructions to write the latches
; 0th_program_word
MOV
MOV
#LOW_WORD_0, W2
#HIGH_BYTE_0, W3
;
;
TBLWTL W2, [W0]
TBLWTH W3, [W0++]
; Write PM low word into program latch
; Write PM high byte into program latch
; 1st_program_word
MOV
MOV
#LOW_WORD_1, W2
#HIGH_BYTE_1, W3
;
;
TBLWTL W2, [W0]
TBLWTH W3, [W0++]
; Write PM low word into program latch
; Write PM high byte into program latch
;
2nd_program_word
MOV
MOV
#LOW_WORD_2, W2
#HIGH_BYTE_2, W3
;
;
TBLWTL W2, [W0]
TBLWTH W3, [W0++]
; Write PM low word into program latch
; Write PM high byte into program latch
•
•
•
; 63rd_program_word
MOV
MOV
#LOW_WORD_31, W2
#HIGH_BYTE_31, W3
;
;
TBLWTL W2, [W0]
TBLWTH W3, [W0++]
; Write PM low word into program latch
; Write PM high byte into program latch
EXAMPLE 5-3:
INITIATING A PROGRAMMING SEQUENCE
DISI
#5
; Block all interrupts with priority <7
; for next 5 instructions
MOV
MOV
MOV
MOV
BSET
NOP
NOP
#0x55, W0
W0, NVMKEY
#0xAA, W1
W1, NVMKEY
NVMCON, #WR
; Write the 55 key
;
; Write the AA key
; Start the erase sequence
; Insert two NOPs after the
; erase command is asserted
DS70000318G-page 88
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
A simplified block diagram of the Reset module is
shown in Figure 6-1.
6.0
RESETS
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “Reset” (DS70192) in the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
Any active source of Reset will make the SYSRST
signal active. On system Reset, some of the registers
associated with the CPU and peripherals are forced to
a known Reset state and some are unaffected.
Note:
Refer to the specific peripheral section or
Section 3.0 “CPU” of this data sheet for
register Reset states.
All types of device Reset set a corresponding status bit
in the RCON register to indicate the type of Reset (see
Register 6-1).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
A POR clears all the bits, except for the POR bit
(RCON<0>), which is set. The user application can set
or clear any bit at any time during code execution. The
RCON bits only serve as status bits. Setting a particular
Reset status bit in software does not cause a device
Reset to occur.
The Reset module combines all Reset sources and
controls the device Master Reset Signal, SYSRST. The
following is a list of device Reset sources:
The RCON register also has other bits associated with
the Watchdog Timer and device power-saving states.
The function of these bits is discussed in other sections
of this manual.
• POR: Power-on Reset
• BOR: Brown-out Reset
Note:
The status bits in the RCON register
should be cleared after they are read so
that the next RCON register value after a
device Reset is meaningful.
• MCLR: Master Clear Pin Reset
• SWR: Software RESETInstruction
• WDTO: Watchdog Timer Reset
• CM: Configuration Mismatch Reset
• TRAPR: Trap Conflict Reset
• IOPUWR: Illegal Condition Device Reset
- Illegal Opcode Reset
- Uninitialized W Register Reset
- Security Reset
FIGURE 6-1:
RESET SYSTEM BLOCK DIAGRAM
RESETInstruction
Glitch Filter
MCLR
WDT
Module
Sleep or Idle
BOR
Internal
Regulator
SYSRST
VDD
POR
VDD Rise
Detect
Trap Conflict
Illegal Opcode
Uninitialized W Register
Configuration Mismatch
2008-2014 Microchip Technology Inc.
DS70000318G-page 89
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 6-1:
RCON: RESET CONTROL REGISTER(1)
R/W-0
TRAPR
bit 15
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
CM
R/W-0
IOPUWR
VREGS
bit 8
R/W-0
EXTR
R/W-0
SWR
R/W-0
SWDTEN(2)
R/W-0
WDTO
R/W-0
R/W-0
IDLE
R/W-1
BOR
R/W-1
POR
SLEEP
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
bit 14
TRAPR: Trap Reset Flag bit
1= A Trap Conflict Reset has occurred
0= A Trap Conflict Reset has not occurred
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1= An illegal opcode detection, an illegal address mode or Uninitialized W register used as an
Address Pointer caused a Reset
0= An illegal opcode or Uninitialized W register Reset has not occurred
bit 13-10
bit 9
Unimplemented: Read as ‘0’
CM: Configuration Mismatch Flag bit
1= A Configuration Mismatch Reset has occurred
0= A Configuration Mismatch Reset has NOT occurred
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
VREGS: Voltage Regulator Standby During Sleep bit
1= Voltage regulator is active during Sleep
0= Voltage regulator goes into Standby mode during Sleep
EXTR: External Reset Pin (MCLR) bit
1= A Master Clear (pin) Reset has occurred
0= A Master Clear (pin) Reset has not occurred
SWR: Software Reset Flag (Instruction) bit
1= A RESETinstruction has been executed
0= A RESETinstruction has not been executed
SWDTEN: Software Enable/Disable of WDT bit(2)
1= WDT is enabled
0= WDT is disabled
WDTO: Watchdog Timer Time-out Flag bit
1= WDT time-out has occurred
0= WDT time-out has not occurred
SLEEP: Wake-up from Sleep Flag bit
1= Device has been in Sleep mode
0= Device has not been in Sleep mode
IDLE: Wake-up from Idle Flag bit
1= Device was in Idle mode
0= Device was not in Idle mode
Note 1: All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
DS70000318G-page 90
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 6-1:
RCON: RESET CONTROL REGISTER(1) (CONTINUED)
bit 1
bit 0
BOR: Brown-out Reset Flag bit
1= A Brown-out Reset has occurred
0= A Brown-out Reset has not occurred
POR: Power-on Reset Flag bit
1= A Power-on Reset has occurred
0= A Power-on Reset has not occurred
Note 1: All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
2008-2014 Microchip Technology Inc.
DS70000318G-page 91
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
A Warm Reset is the result of all the other Reset
6.1
System Reset
sources, including the RESET instruction. On Warm
Reset, the device will continue to operate from the
current clock source as indicated by the Current
Oscillator Selection (COSC<2:0>) bits in the Oscillator
Control (OSCCON<14:12>) register.
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 families of devices have two types of Reset:
• Cold Reset
• Warm Reset
The device is kept in a Reset state until the system
power supplies have stabilized at appropriate levels
and the oscillator clock is ready. The sequence in
which this occurs is detailed in Figure 6-2.
A Cold Reset is the result of a Power-on Reset (POR)
or a Brown-out Reset (BOR). On a Cold Reset, the
FNOSCx Configuration bits in the FOSC Configuration
register select the device clock source.
TABLE 6-1:
OSCILLATOR DELAY
Oscillator
Oscillator
Startup Timer
Oscillator Mode
PLL Lock Time
Total Delay
Startup Delay
(1)
(1)
FRC, FRCDIV16,
FRCDIVN
TOSCD
—
—
TOSCD
(1)
(3)
(1,3)
FRCPLL
XT
TOSCD
—
TLOCK
TOSCD + TLOCK
(1)
(2)
(1,2)
(1,2)
TOSCD
TOST
—
—
—
TOSCD + TOST
TOSCD + TOST
—
(1)
(2)
HS
TOSCD
TOST
EC
—
—
(1)
(2)
(3)
(1,2,3)
XTPLL
HSPLL
ECPLL
LPRC
TOSCD
TOST
TLOCK
TOSCD + TOST + TLOCK
TOSCD + TOST + TLOCK
(1)
(2)
(3)
(1,2,3)
TOSCD
TOST
TLOCK
(3)
(3)
—
—
—
TLOCK
TLOCK
(1)
(1)
TOSCD
—
TOSCD
Note 1: TOSCD = Oscillator start-up delay (1.1 s max for FRC, 70 s max for LPRC). Crystal oscillator start-up
times vary with crystal characteristics, load capacitance, etc.
2: TOST = Oscillator Start-up Timer delay (1024 oscillator clock period). For example, TOST = 102.4 s for a
10 MHz crystal and TOST = 32 ms for a 32 kHz crystal.
3: TLOCK = PLL lock time (1.5 ms nominal) if PLL is enabled.
DS70000318G-page 92
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 6-2:
SYSTEM RESET TIMING
VBOR
VPOR
VDD
TPOR
1
POR Reset
BOR Reset
SYSRST
TBOR
2
3
TPWRT
4
Oscillator Clock
TLOCK
TOSCD
TOST
6
TFSCM
FSCM
5
Reset
Device Status
Run
Time
Note 1: POR Reset: A POR circuit holds the device in Reset when the power supply is turned on. The POR circuit is active
until VDD crosses the VPOR threshold and the delay, TPOR, has elapsed.
2: BOR Reset: The on-chip voltage regulator has a BOR circuit that keeps the device in Reset until VDD crosses the
VBOR threshold and the delay, TBOR, has elapsed. The delay, TBOR, ensures the voltage regulator output becomes
stable.
3: PWRT Timer: The programmable power-up timer continues to hold the processor in Reset for a specific period of
time (TPWRT) after a BOR. The delay, TPWRT, ensures that the system power supplies have stabilized at the appro-
priate level for full-speed operation. After the delay, TPWRT has elapsed and the SYSRST becomes inactive, which in
turn, enables the selected oscillator to start generating clock cycles.
4: Oscillator Delay: The total delay for the clock to be ready for various clock source selections is given in Table 6-1.
Refer to Section 8.0 “Oscillator Configuration” for more information.
5: When the oscillator clock is ready, the processor begins execution from location, 0x000000. The user application
programs a GOTO instruction at the Reset address, which redirects program execution to the appropriate start-up
routine.
6: If the Fail-Safe Clock Monitor (FSCM) is enabled, it begins to monitor the system clock when the system clock is ready
and the delay, TFSCM, has elapsed.
TABLE 6-2:
Symbol
OSCILLATOR DELAY
Parameter Value
Note: When the device exits the Reset
condition (begins normal operation), the
device operating parameters (voltage,
frequency, temperature, etc.) must be
within their operating ranges; otherwise,
the device may not function correctly.
The user application must ensure that
the delay between the time power is first
applied, and the time SYSRST becomes
inactive, is long enough to get all
operating parameters within specification.
VPOR
TPOR
VBOR
TBOR
POR Threshold
1.8V nominal
POR Extension Time
BOR Threshold
30 s maximum
2.5V nominal
BOR Extension Time
100 s maximum
0-128 ms nominal
TPWRT Programmable
Power-up Time Delay
TFSCM
Fail-Safe Clock Monitor 900 s maximum
Delay
2008-2014 Microchip Technology Inc.
DS70000318G-page 93
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
VBOR threshold and the delay, TBOR, has elapsed. The
delay, TBOR, ensures the voltage regulator output
becomes stable.
6.2
Power-on Reset (POR)
A Power-on Reset (POR) circuit ensures the device is
reset from power-on. The POR circuit is active until
VDD crosses the VPOR threshold and the delay, TPOR,
has elapsed. The delay, TPOR, ensures the internal
device bias circuits become stable.
The BOR status (BOR) bit in the Reset Control
(RCON<1>) register is set to indicate the Brown-out
Reset.
The device will not run at full speed after a BOR as the
VDD should rise to acceptable levels for full-speed
operation. The PWRT provides power-up time delay
(TPWRT) to ensure that the system power supplies have
stabilized at the appropriate levels for full-speed
operation before the SYSRST is released.
The device supply voltage characteristics must meet
the specified starting voltage and rise rate
requirements to generate the POR. Refer to
Section 24.0 “Electrical Characteristics” for details.
The POR status (POR) bit in the Reset Control
(RCON<0>) register is set to indicate the Power-on
Reset.
The Power-up Timer Delay (TPWRT) is programmed by
the
Power-on
Reset
Timer
Value
Select
(FPWRT<2:0>) bits in the FPOR Configuration
(FPOR<2:0>) register, which provides eight settings
(from 0 ms to 128 ms). Refer to Section 21.0 “Special
Features” for further details.
6.2.1
Brown-out Reset (BOR) and
Power-up Timer (PWRT)
The on-chip regulator has a Brown-out Reset (BOR)
circuit that resets the device when the VDD is too low
(VDD < VBOR) for proper device operation. The BOR
circuit keeps the device in Reset until VDD crosses the
Figure 6-3 shows the typical brown-out scenarios. The
Reset delay (TBOR + TPWRT) is initiated each time VDD
rises above the VBOR trip point.
FIGURE 6-3:
BROWN-OUT SITUATIONS
VDD
VBOR
TBOR + TPWRT
SYSRST
VDD
VBOR
TBOR + TPWRT
SYSRST
VDD Dips before PWRT Expires
VDD
VBOR
TBOR + TPWRT
SYSRST
DS70000318G-page 94
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
6.3
External Reset (EXTR)
6.6
Trap Conflict Reset
The External Reset is generated by driving the MCLR
pin low. The MCLR pin is a Schmitt trigger input with an
additional glitch filter. Reset pulses that are longer than
the minimum pulse width will generate a Reset. Refer
to Section 24.0 “Electrical Characteristics” for
minimum pulse width specifications. The External
Reset (MCLR) pin (EXTR) bit in the Reset Control
(RCON) register is set to indicate the MCLR Reset.
If a lower priority hard trap occurs while a higher
priority trap is being processed, a hard Trap Conflict
Reset occurs. The hard traps include exceptions of
Priority Levels 13 through 15, inclusive. The address
error (Level 13) and oscillator error (Level 14) traps fall
into this category.
The Trap Reset (TRAPR) flag in the Reset Control
(RCON<15>) register is set to indicate the Trap Conflict
Reset. Refer to Section 7.0 “Interrupt Controller” for
more information on Trap Conflict Resets.
6.3.0.1
EXTERNAL SUPERVISORY
CIRCUIT
Many systems have external supervisory circuits that
generate Reset signals to reset multiple devices in the
system. This External Reset signal can be directly
connected to the MCLR pin to reset the device when
the rest of the system is reset.
6.7
Configuration Mismatch Reset
To maintain the integrity of the Peripheral Pin Select
Control registers, they are constantly monitored with
shadow registers in hardware. If an unexpected
change in any of the registers occur (such as cell
disturbances caused by ESD or other external events),
a Configuration Mismatch Reset occurs.
6.3.0.2
INTERNAL SUPERVISORY CIRCUIT
When using the internal power supervisory circuit to
reset the device, the External Reset pin (MCLR) should
be tied directly or resistively to VDD. In this case, the
MCLR pin will not be used to generate a Reset. The
External Reset pin (MCLR) does not have an internal
pull-up and must not be left unconnected.
The Configuration Mismatch (CM) flag in the Reset
Control (RCON<9>) register is set to indicate the
Configuration Mismatch Reset. Refer to Section 10.0
“I/O Ports” for more information on the
Configuration Mismatch Reset.
Note:
The Configuration Mismatch Reset
feature and associated Reset flag are not
available on all devices.
6.4
Software RESET Instruction (SWR)
Whenever the RESET instruction is executed, the
device will assert SYSRST, placing the device in a
special Reset state. This Reset state will not
re-initialize the clock. The clock source in effect prior to
the RESETinstruction will remain. SYSRST is released
at the next instruction cycle and the Reset vector fetch
will commence.
6.8
Illegal Condition Device Reset
An illegal condition device Reset occurs due to the
following sources:
• Illegal Opcode Reset
• Uninitialized W Register Reset
• Security Reset
The Software Reset (SWR) flag (instruction) in the
Reset Control (RCON<6>) register is set to indicate
the Software Reset.
The Illegal Opcode or Uninitialized W Access Reset
(IOPUWR) flag in the Reset Control (RCON<14>)
register is set to indicate the illegal condition device
Reset.
6.5
Watchdog Timer Time-out Reset
(WDTO)
6.8.1
ILLEGAL OPCODE RESET
Whenever a Watchdog time-out occurs, the device will
asynchronously assert SYSRST. The clock source will
remain unchanged. A WDT time-out during Sleep or
Idle mode will wake-up the processor, but will not reset
the processor.
A device Reset is generated if the device attempts to
execute an illegal opcode value that is fetched from
program memory.
The Illegal Opcode Reset function can prevent the
device from executing program memory sections that
are used to store constant data. To take advantage of
the Illegal Opcode Reset, use only the lower 16 bits of
each program memory section to store the data values.
The upper 8 bits should be programmed with 3Fh,
which is an illegal opcode value.
The Watchdog Timer Time-out (WDTO) flag in the
Reset Control (RCON<4>) register is set to indicate
the Watchdog Timer Reset. Refer to Section 21.4
“Watchdog Timer (WDT)” for more information on
the Watchdog Timer Reset.
2008-2014 Microchip Technology Inc.
DS70000318G-page 95
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The VFC occurs when the Program Counter is
reloaded with an interrupt or trap vector.
6.8.2
UNINITIALIZED W REGISTER
RESET
Refer to Section 21.8 “Code Protection and
CodeGuard™ Security” for more information on
Security Reset.
Any attempt to use the Uninitialized W register as an
Address Pointer will reset the device. The W register
array (with the exception of W15) is cleared during all
Resets and is considered uninitialized until written to.
6.9
Using the RCON Status Bits
6.8.3
SECURITY RESET
The user application can read the Reset Control
(RCON) register after any device Reset to determine
the cause of the Reset.
If a Program Flow Change (PFC) or Vector Flow
Change (VFC) targets a restricted location in a
protected segment (boot and secure segment), that
operation will cause a Security Reset.
Note: The status bits in the RCON register
should be cleared after they are read so
that the next RCON register value after a
device Reset will be meaningful.
The PFC occurs when the Program Counter is
reloaded as a result of a call, jump, computed jump,
return, return from subroutine or other form of branch
instruction.
Table 6-3 provides a summary of the Reset flag bit
operation.
TABLE 6-3:
RESET FLAG BIT OPERATION
Set by:
Trap conflict event
Flag Bit
Cleared by:
TRAPR (RCON<15>)
IOPWR (RCON<14>)
POR, BOR
Illegal opcode or Uninitialized W register
access or Security Reset
POR, BOR
CM (RCON<9>)
Configuration Mismatch
MCLR Reset
POR, BOR
POR
EXTR (RCON<7>)
SWR (RCON<6>)
WDTO (RCON<4>)
RESETinstruction
WDT time-out
POR, BOR
PWRSAVinstruction, CLRWDTinstruction,
POR, BOR
SLEEP (RCON<3>)
IDLE (RCON<2>)
BOR (RCON<1>)
POR (RCON<0>)
PWRSAV #SLEEPinstruction
PWRSAV #IDLEinstruction
POR, BOR
POR, BOR
POR, BOR
—
—
POR
Note: All Reset flag bits can be set or cleared by user software.
DS70000318G-page 96
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Interrupt vectors are prioritized in terms of their natural
7.0
INTERRUPT CONTROLLER
priority. This priority is linked to their position in the
vector table. Lower addresses generally have a higher
natural priority. For example, the interrupt associated
with Vector 0 will take priority over interrupts at any
other vector address.
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “Interrupts (Part IV)”
(DS70300) in the “dsPIC33F/PIC24H
Family Reference Manual”, which is
available on the Microchip web site
(www.microchip.com).
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices implement up to 35 unique interrupts and
4 non-maskable traps. These are summarized in
Table 7-1.
7.1.1
ALTERNATE INTERRUPT VECTOR
TABLE
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The Alternate Interrupt Vector Table (AIVT) is located
after the IVT, as shown in Figure 7-1. Access to the
AIVT is provided by the ALTIVT control bit
(INTCON2<15>). If the ALTIVT bit is set, all interrupt
and exception processes use the alternate vectors
instead of the default vectors. The alternate vectors are
organized in the same manner as the default vectors.
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 interrupt controller reduces the numerous
peripheral interrupt request signals to a single interrupt
request signal to the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 CPU. It has the following
features:
The AIVT supports debugging by providing a means to
switch between an application and a support environ-
ment without requiring the interrupt vectors to be
reprogrammed. This feature also enables switching
between applications for evaluation of different
software algorithms at run time. If the AIVT is not
needed, the AIVT should be programmed with the
same addresses used in the IVT.
• Up to eight processor exceptions and software
traps
• Seven user-selectable priority levels
• Interrupt Vector Table (IVT) with up to 118 vectors
7.2
Reset Sequence
• A unique vector for each interrupt or exception
source
A device Reset is not a true exception because the
interrupt controller is not involved in the Reset process.
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices clear their registers in response to a Reset,
which forces the PC to zero. The Digital Signal Controller
then begins program execution at location, 0x000000. A
GOTO instruction at the Reset address can redirect
program execution to the appropriate start-up routine.
• Fixed priority within a specified user priority level
• Alternate Interrupt Vector Table (AIVT) for debug
support
• Fixed interrupt entry and return latencies
7.1
Interrupt Vector Table
The Interrupt Vector Table (IVT) is shown in Figure 7-1.
The IVT resides in program memory, starting at location
000004h. The IVT contains 126 vectors, consisting of
eight nonmaskable trap vectors, plus up to 118 sources
of interrupt. In general, each interrupt source has its own
vector. Each interrupt vector contains a 24-bit-wide
address. The value programmed into each interrupt
vector location is the starting address of the associated
Interrupt Service Routine (ISR).
Note: Any unimplemented or unused vector
locations in the IVT and AIVT should be
programmed with the address of a default
interrupt handler routine that contains a
RESETinstruction.
2008-2014 Microchip Technology Inc.
DS70000318G-page 97
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 7-1:
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 INTERRUPT VECTOR
TABLE
Reset – GOTOInstruction
Reset – GOTOAddress
Reserved
0x000000
0x000002
0x000004
Oscillator Fail Trap Vector
Address Error Trap Vector
Stack Error Trap Vector
Math Error Trap Vector
Reserved
Reserved
Reserved
Interrupt Vector 0
Interrupt Vector 1
~
0x000014
~
~
Interrupt Vector 52
Interrupt Vector 53
Interrupt Vector 54
~
0x00007C
0x00007E
0x000080
(1)
Interrupt Vector Table (IVT)
~
~
Interrupt Vector 116
Interrupt Vector 117
Reserved
0x0000FC
0x0000FE
0x000100
0x000102
Reserved
Reserved
Oscillator Fail Trap Vector
Address Error Trap Vector
Stack Error Trap Vector
Math Error Trap Vector
Reserved
Reserved
Reserved
Interrupt Vector 0
Interrupt Vector 1
~
0x000114
~
~
(1)
Alternate Interrupt Vector Table (AIVT)
Interrupt Vector 52
Interrupt Vector 53
Interrupt Vector 54
~
0x00017C
0x00017E
0x000180
~
~
Interrupt Vector 116
Interrupt Vector 117
Start of Code
0x0001FE
0x000200
Note 1: See Table 7-1 for the list of implemented interrupt vectors.
DS70000318G-page 98
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 7-1:
INTERRUPT VECTORS
Interrupt
Vector
Number
Request
(IQR)
IVT Address
AIVT Address
Interrupt Source
Highest Natural Order Priority
0x000114
8
9
0
1
0x000014
0x000016
0x000018
0x00001A
0x00001C
0x00001E
0x000020
0x000022
0x000024
0x000026
0x000028
0x00002A
0x00002C
0x00002E
INT0 – External Interrupt 0
IC1 – Input Capture 1
OC1 – Output Compare 1
T1 – Timer1
0x000116
10
2
0x000118
11
3
0x00011A
12
4
0x00011C
Reserved
13
5
0x00011E
IC2 – Input Capture 2
OC2 – Output Compare 2
T2 – Timer2
14
6
0x000120
15
7
0x000122
16
8
0x000124
T3 – Timer3
17
9
0x000126
SPI1E – SPI1 Fault
18
10
0x000128
SPI1 – SPI1 Transfer Done
U1RX – UART1 Receiver
U1TX – UART1 Transmitter
ADC – ADC Group Convert Done
19
11
0x00012A
20
12
0x00012C
0x00012E
21
13
22-23
24
14-15
16
0x000030-0x000032 0x000130-0x000132 Reserved
0x000034
0x000036
0x000038
0x00003A
0x00003C
0x000134
0x000136
0x000138
0x00013A
0x00013C
SI2C1 – I2C1 Slave Event
25
17
MI2C1 – I2C1 Master Event
26
18
CMP1 – Analog Comparator 1 Interrupt
CN – Input Change Notification Interrupt
INT1 – External Interrupt 1
27
19
28
20
29-36
37
21-28
29
0x00003E-0x00004C 0x00013E-0x00014C Reserved
0x00004E 0x00014E INT2 – External Interrupt 2
0x000050-0x000084 0x000150-0x000184 Reserved
0x000086 0x000186 PWM PSEM Special Event Match
0x000088-0x000094 0x000188-0x000194 Reserved
0x000096 0x000196 U1E – UART1 Error Interrupt
0x000098-0x0000CE 0x000198-0x0001CE Reserved
38-64
65
30-56
57
66-72
73
58-64
65
74-101
102
103
104
105
106-110
111
112
113
114-117
118
119
120
121
122
123
124
125
66-93
94
0x0000D0
0x0000D2
0x0000D4
0x0000D6
0x0001D0
0x0001D2
0x0001D4
0x0001D6
PWM1 – PWM1 Interrupt
PWM2 – PWM2 Interrupt
PWM3 – PWM3 Interrupt
PWM4 – PWM4 Interrupt
95
96
97
98-102
103
104
105
106-109
110
111
112
113
114
115
116
117
0x0000D8-0x0000E0 0x0001D8-0x0001E0 Reserved
0x0000E2
0x0000E4
0x0000E6
0x00001E2
0x0001E4
0x0001E6
CMP2 – Analog Comparator 2
CMP3 – Analog Comparator 3
CMP4 – Analog Comparator 4
0x0000E8-0x0000EE 0x0001E8-0x0001EE Reserved
0x0000F0
0x0000F2
0x0000F4
0x0000F6
0x0000F8
0x0000FA
0x0000FC
0x0000FE
0x0001F0
0x0001F2
ADC Pair 0 Convert Done
ADC Pair 1 Convert Done
ADC Pair 2 Convert Done
ADC Pair 3 Convert Done
ADC Pair 4 Convert Done
ADC Pair 5 Convert Done
ADC Pair 6 Convert Done
Reserved
0x0001F4
0x0001F6
0x0001F8
0x0001FA
0x0001FC
0x0001FE
Lowest Natural Order Priority
2008-2014 Microchip Technology Inc.
DS70000318G-page 99
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
7.3.5
INTTREG
7.3
Interrupt Control and Status
Registers
The INTTREG register contains the associated
interrupt vector number and the new CPU Interrupt Pri-
ority Level, which are latched into the Vector Number
(VECNUM<6:0>) and Interrupt Level (ILR<3:0>) bit
fields in the INTTREG register. The new Interrupt
Priority Level is the priority of the pending interrupt.
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices implement 27 registers for the interrupt
controller:
• INTCON1
• INTCON2
• IFSx
• IECx
• IPCx
The interrupt sources are assigned to the IFSx, IECx
and IPCx registers in the same sequence that they are
listed in Table 7-1. For example, the INT0 (External
Interrupt 0) is shown as having Vector Number 8 and a
natural order priority of 0. Thus, the INT0IF bit is found
in IFS0<0>, the INT0IE bit is found in IEC0<0> and the
INT0IP bits are found in the first position of IPC0
(IPC0<2:0>).
• INTTREG
7.3.1
INTCON1 AND INTCON2
Global interrupt control functions are controlled from
INTCON1 and INTCON2. INTCON1 contains the
Interrupt Nesting Disable (NSTDIS) bit as well as the
control and status flags for the processor trap sources.
The INTCON2 register controls the external interrupt
request signal behavior and the use of the Alternate
Interrupt Vector Table.
7.3.6
STATUS/CONTROL REGISTERS
Although they are not specifically part of the interrupt
control hardware, two of the CPU Control registers
contain bits that control interrupt functionality.
• The CPU STATUS Register, SR, contains the
IPL<2:0> bits (SR<7:5>). These bits indicate the
current CPU Interrupt Priority Level. The user can
change the current CPU priority level by writing to
the IPL bits.
7.3.2
IFSx
The IFSx registers maintain all of the interrupt request
flags. Each source of interrupt has a status bit, which is
set by the respective peripherals or external signal and
is cleared via software.
• The CORCON register contains the IPL3 bit,
which together with IPL<2:0>, indicates the
current CPU priority level. IPL3 is a read-only bit
so that trap events cannot be masked by the user
software.
7.3.3
IECx
The IECx registers maintain all of the interrupt enable
bits. These control bits are used to individually enable
interrupts from the peripherals or external signals.
All Interrupt registers are described in Register 7-1
through Register 7-35 in the following pages.
7.3.4
IPCx
The IPCx registers are used to set the Interrupt Priority
Level for each source of interrupt. Each user interrupt
source can be assigned to one of eight priority levels.
DS70000318G-page 100
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-1:
SR: CPU STATUS REGISTER(1)
R-0
OA
R-0
OB
R/C-0
SA
R/C-0
SB
R-0
R/C-0
SAB
R -0
DA
R/W-0
DC
OAB
bit 15
bit 8
R/W-0(3)
IPL2(2)
bit 7
R/W-0(3)
IPL1(2)
R/W-0(3)
IPL0(2)
R-0
RA
R/W-0
N
R/W-0
OV
R/W-0
Z
R/W-0
C
bit 0
Legend:
C = Clearable bit
W = Writable bit
‘1’ = Bit is set
R = Readable bit
-n = Value at POR
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-5
IPL<2:0>: CPU Interrupt Priority Level Status bits(2,3)
111= CPU Interrupt Priority Level is 7 (15), user interrupts disabled
110= CPU Interrupt Priority Level is 6 (14)
101= CPU Interrupt Priority Level is 5 (13)
100= CPU Interrupt Priority Level is 4 (12)
011= CPU Interrupt Priority Level is 3 (11)
010= CPU Interrupt Priority Level is 2 (10)
001= CPU Interrupt Priority Level is 1 (9)
000= CPU Interrupt Priority Level is 0 (8)
Note 1: For complete register details, see Register 3-1.
2: The IPL<2:0> bits are concatenated with the IPL<3> bit (CORCON<3>) to form the CPU Interrupt Priority
Level. The value in parentheses indicates the IPL if IPL<3> = 1. User interrupts are disabled when
IPL<3> = 1.
3: The IPL<2:0> status bits are read-only when NSTDIS (INTCON1<15>) = 1.
REGISTER 7-2:
CORCON: CORE CONTROL REGISTER(1)
U-0
—
U-0
—
U-0
—
R/W-0
US
R/W-0
EDT
R-0
R-0
R-0
DL2
DL1
DL0
bit 15
bit 8
R/W-0
SATA
R/W-0
SATB
R/W-1
R/W-0
R/C-0
IPL3(2)
R/W-0
PSV
R/W-0
RND
R/W-0
IF
SATDW
ACCSAT
bit 7
bit 0
Legend:
C = Clearable bit
W = Writable bit
‘x = Bit is unknown
R = Readable bit
0’ = Bit is cleared
-n = Value at POR
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
bit 3
IPL3: CPU Interrupt Priority Level Status bit 3(2)
1= CPU Interrupt Priority Level is greater than 7
0= CPU Interrupt Priority Level is 7 or less
Note 1: For complete register details, see Register 3-2.
2: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level.
2008-2014 Microchip Technology Inc.
DS70000318G-page 101
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-3:
INTCON1: INTERRUPT CONTROL REGISTER 1
R/W-0
NSTDIS
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
OVAERR
OVBERR
COVAERR COVBERR
OVATE
OVBTE
COVTE
bit 8
R/W-0
SFTACERR
bit 7
R/W-0
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
U-0
—
DIV0ERR
MATHERR ADDRERR
STKERR
OSCFAIL
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
NSTDIS: Interrupt Nesting Disable bit
1= Interrupt nesting is disabled
0= Interrupt nesting is enabled
OVAERR: Accumulator A Overflow Trap Flag bit
1= Trap was caused by overflow of Accumulator A
0= Trap was not caused by overflow of Accumulator A
OVBERR: Accumulator B Overflow Trap Flag bit
1= Trap was caused by overflow of Accumulator B
0= Trap was not caused by overflow of Accumulator B
COVAERR: Accumulator A Catastrophic Overflow Trap Flag bit
1= Trap was caused by catastrophic overflow of Accumulator A
0= Trap was not caused by catastrophic overflow of Accumulator A
COVBERR: Accumulator B Catastrophic Overflow Trap Flag bit
1= Trap was caused by catastrophic overflow of Accumulator B
0= Trap was not caused by catastrophic overflow of Accumulator B
OVATE: Accumulator A Overflow Trap Enable bit
1= Trap overflow of Accumulator A
0= Trap is disabled
OVBTE: Accumulator B Overflow Trap Enable bit
1= Trap overflow of Accumulator B
0= Trap is disabled
bit 8
COVTE: Catastrophic Overflow Trap Enable bit
1= Trap on catastrophic overflow of Accumulator A or B enabled
0= Trap is disabled
bit 7
SFTACERR: Shift Accumulator Error Status bit
1= Math error trap was caused by an invalid accumulator shift
0= Math error trap was not caused by an invalid accumulator shift
bit 6
DIV0ERR: Arithmetic Error Status bit
1= Math error trap was caused by a divide-by-zero
0= Math error trap was not caused by a divide-by-zero
bit 5
bit 4
Unimplemented: Read as ‘0’
MATHERR: Arithmetic Error Status bit
1= Math error trap has occurred
0= Math error trap has not occurred
bit 3
ADDRERR: Address Error Trap Status bit
1= Address error trap has occurred
0= Address error trap has not occurred
DS70000318G-page 102
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-3:
INTCON1: INTERRUPT CONTROL REGISTER 1 (CONTINUED)
bit 2
bit 1
bit 0
STKERR: Stack Error Trap Status bit
1= Stack error trap has occurred
0= Stack error trap has not occurred
OSCFAIL: Oscillator Failure Trap Status bit
1= Oscillator failure trap has occurred
0= Oscillator failure trap has not occurred
Unimplemented: Read as ‘0’
2008-2014 Microchip Technology Inc.
DS70000318G-page 103
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-4:
INTCON2: INTERRUPT CONTROL REGISTER 2
R/W-0
ALTIVT
bit 15
R-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
DISI
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
INT2EP
INT1EP
INT0EP
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
bit 14
ALTIVT: Enable Alternate Interrupt Vector Table bit
1= Use alternate vector table
0= Use standard (default) vector table
DISI: DISIInstruction Status bit
1= DISIinstruction is active
0= DISIinstruction is not active
bit 13-3
bit 2
Unimplemented: Read as ‘0’
INT2EP: External Interrupt 2 Edge Detect Polarity Select bit
1= Interrupt on negative edge
0= Interrupt on positive edge
bit 1
bit 0
INT1EP: External Interrupt 1 Edge Detect Polarity Select bit
1= Interrupt on negative edge
0= Interrupt on positive edge
INT0EP: External Interrupt 0 Edge Detect Polarity Select bit
1= Interrupt on negative edge
0= Interrupt on positive edge
DS70000318G-page 104
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-5:
IFS0: INTERRUPT FLAG STATUS REGISTER 0
U-0
—
U-0
—
R/W-0
ADIF
R/W-0
R/W-0
R/W-0
SPI1IF
R/W-0
R/W-0
T3IF
U1TXIF
U1RXIF
SPI1EIF
bit 15
bit 8
R/W-0
T2IF
R/W-0
OC2IF
R/W-0
IC2IF
U-0
—
R/W-0
T1IF
R/W-0
OC1IF
R/W-0
IC1IF
R/W-0
INT0IF
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13
Unimplemented: Read as ‘0’
ADIF: ADC Group Conversion Complete Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 12
bit 11
bit 10
bit 9
U1TXIF: UART1 Transmitter Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
U1RXIF: UART1 Receiver Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
SPI1IF: SPI1 Event Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
SPI1EIF: SPI1 Fault Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 8
T3IF: Timer3 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 7
T2IF: Timer2 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 6
OC2IF: Output Compare Channel 2 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 5
IC2IF: Input Capture Channel 2 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 4
bit 3
Unimplemented: Read as ‘0’
T1IF: Timer1 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 2
OC1IF: Output Compare Channel 1 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
2008-2014 Microchip Technology Inc.
DS70000318G-page 105
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-5:
IFS0: INTERRUPT FLAG STATUS REGISTER 0 (CONTINUED)
bit 1
bit 0
IC1IF: Input Capture Channel 1 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
INT0IF: External Interrupt 0 Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
DS70000318G-page 106
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-6:
IFS1: INTERRUPT FLAG STATUS REGISTER 1
U-0
—
U-0
—
R/W-0
INT2IF
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
U-0
—
R/W-0
INT1IF
R/W-0
CNIF
R/W-0
AC1IF
R/W-0
R/W-0
MI2C1IF
SI2C1IF
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13
Unimplemented: Read as ‘0’
INT2IF: External Interrupt 2 Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 12-5
bit 4
Unimplemented: Read as ‘0’
INT1IF: External Interrupt 1 Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 3
bit 2
bit 1
bit 0
CNIF: Input Change Notification Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
AC1IF: Analog Comparator 1 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
MI2C1IF: I2C1 Master Events Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
SI2C1IF: I2C1 Slave Events Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
2008-2014 Microchip Technology Inc.
DS70000318G-page 107
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-7:
IFS3: INTERRUPT FLAG STATUS REGISTER 3
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
U-0
—
PSEMIF
bit 15
bit 8
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-10
bit 9
Unimplemented: Read as ‘0’
PSEMIF: PWM Special Event Match Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 8-0
Unimplemented: Read as ‘0’
REGISTER 7-8:
IFS4: INTERRUPT FLAG STATUS REGISTER 4
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
U1EIF
U-0
—
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-2
bit 1
Unimplemented: Read as ‘0’
U1EIF: UART1 Error Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 0
Unimplemented: Read as ‘0’
DS70000318G-page 108
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-9:
IFS5: INTERRUPT FLAG STATUS REGISTER 5
R/W-0
PWM2IF
bit 15
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
PWM1IF
bit 8
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
PWM2IF: PWM2 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 14
PWM1IF: PWM1 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 13-0
Unimplemented: Read as ‘0’
2008-2014 Microchip Technology Inc.
DS70000318G-page 109
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-10: IFS6: INTERRUPT FLAG STATUS REGISTER 6
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
AC4IF
R/W-0
AC3IF
ADCP1IF
ADCP0IF
bit 15
bit 8
R/W-0
AC2IF
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
PWM4IF
PWM3IF
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
bit 14
ADCP1IF: ADC Pair 1 Conversion Done Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
ADCP0IF: ADC Pair 0 Conversion Done Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 13-10
bit 9
Unimplemented: Read as ‘0’
AC4IF: Analog Comparator 4 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 8
bit 7
AC3IF: Analog Comparator 3 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
AC2IF: Analog Comparator 2 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 6-2
bit 1
Unimplemented: Read as ‘0’
PWM4IF: PWM4 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 0
PWM3IF: PWM3 Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
DS70000318G-page 110
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-11: IFS7: INTERRUPT FLAG STATUS REGISTER 7
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADCP6IF
ADCP5IF
ADCP4IF
ADCP3IF
ADCP2IF
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-5
bit 4
Unimplemented: Read as ‘0’
ADCP6IF: ADC Pair 6 Conversion Done Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
bit 3
bit 2
bit 1
bit 0
ADCP5IF: ADC Pair 5 Conversion Done Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
ADCP4IF: ADC Pair 4 Conversion Done Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
ADCP3IF: ADC Pair 3 Conversion Done Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
ADCP2IF: ADC Pair 2 Conversion Done Interrupt Flag Status bit
1= Interrupt request has occurred
0= Interrupt request has not occurred
2008-2014 Microchip Technology Inc.
DS70000318G-page 111
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-12: IEC0: INTERRUPT ENABLE CONTROL REGISTER 0
U-0
—
U-0
—
R/W-0
ADIE
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
T3IE
U1TXIE
U1RXIE
SPI1IE
SPI1EIE
bit 15
bit 8
R/W-0
T2IE
R/W-0
OC2IE
R/W-0
IC2IE
U-0
—
R/W-0
T1IE
R/W-0
OC1IE
R/W-0
IC1IE
R/W-0
INT0IE
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13
Unimplemented: Read as ‘0’
ADIE: ADC1 Conversion Complete Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 12
bit 11
bit 10
bit 9
U1TXIE: UART1 Transmitter Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
U1RXIE: UART1 Receiver Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
SPI1IE: SPI1 Event Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
SPI1EIE: SPI1 Event Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 8
T3IE: Timer3 Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 7
T2IE: Timer2 Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 6
OC2IE: Output Compare Channel 2 Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 5
IC2IE: Input Capture Channel 2 Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 4
bit 3
Unimplemented: Read as ‘0’
T1IE: Timer1 Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 2
OC1IE: Output Compare Channel 1 Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
DS70000318G-page 112
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-12: IEC0: INTERRUPT ENABLE CONTROL REGISTER 0 (CONTINUED)
bit 1
bit 0
IC1IE: Input Capture Channel 1 Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
INT0IE: External Interrupt 0 Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
2008-2014 Microchip Technology Inc.
DS70000318G-page 113
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-13: IEC1: INTERRUPT ENABLE CONTROL REGISTER 1
U-0
—
U-0
—
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
INT2IE
bit 15
bit 8
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
CNIE
R/W-0
AC1IE
R/W-0
R/W-0
INT1IE
MI2C1IE
SI2C1IE
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13
Unimplemented: Read as ‘0’
INT2IE: External Interrupt 2 Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 12-5
bit 4
Unimplemented: Read as ‘0’
INT1IE: External Interrupt 1 Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 3
bit 2
bit 1
bit 0
CNIE: Input Change Notification Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
AC1IE: Analog Comparator 1 Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
MI2C1IE: I2C1 Master Events Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
SI2C1IE: I2C1 Slave Events Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
DS70000318G-page 114
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-14: IEC3: INTERRUPT ENABLE CONTROL REGISTER 3
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
U-0
—
PSEMIE
bit 15
bit 8
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-10
bit 9
Unimplemented: Read as ‘0’
PSEMIE: PWM Special Event Match Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 8-0
Unimplemented: Read as ‘0’
REGISTER 7-15: IEC4: INTERRUPT ENABLE CONTROL REGISTER 4
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
U1EIE
U-0
—
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-2
bit 1
Unimplemented: Read as ‘0’
U1EIE: UART1 Error Interrupt Enable bit
1= Interrupt request enabled
0= Interrupt request not enabled
bit 0
Unimplemented: Read as ‘0’
2008-2014 Microchip Technology Inc.
DS70000318G-page 115
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-16: IEC5: INTERRUPT ENABLE CONTROL REGISTER 5
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
PWM2IE
PWM1IE
bit 15
bit 8
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
PWM2IE: PWM2 Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
bit 14
PWM1IE: PWM1 Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
bit 13-0
Unimplemented: Read as ‘0’
DS70000318G-page 116
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-17: IEC6: INTERRUPT ENABLE CONTROL REGISTER 6
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
AC4IE
R/W-0
AC3IE
ADCP1IE
ADCP0IE
bit 15
bit 8
R/W-0
AC2IE
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
PWM4IE
PWM3IE
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
bit 14
ADCP1IE: ADC Pair 1 Conversion Done Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
ADCP0IE: ADC Pair 0 Conversion Done Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
bit 13-10
bit 9
Unimplemented: Read as ‘0
AC4IE: Analog Comparator 4 Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
bit 8
bit 7
AC3IE: Analog Comparator 3 Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
AC2IE: Analog Comparator 2 Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
bit 6-2
bit 1
Unimplemented: Read as ‘0’
PWM4IE: PWM4 Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
bit 0
PWM3IE: PWM3 Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
2008-2014 Microchip Technology Inc.
DS70000318G-page 117
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-18: IEC7: INTERRUPT ENABLE CONTROL REGISTER 7
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ADCP6IE
ADCP5IE
ADCP4IE
ADCP3IE
ADCP2IE
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-5
bit 4
Unimplemented: Read as ‘0’
ADCP6IE: ADC Pair 6 Conversion Done Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
bit 3
bit 2
bit 1
bit 0
ADCP5IE: ADC Pair 5 Conversion Done Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
ADCP4IE: ADC Pair 4 Conversion Done Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
ADCP3IE: ADC Pair 3 Conversion Done Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
ADCP2IE: ADC Pair 2 Conversion Done Interrupt Enable bit
1= Interrupt request is enabled
0= Interrupt request is not enabled
DS70000318G-page 118
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-19: IPC0: INTERRUPT PRIORITY CONTROL REGISTER 0
U-0
—
R/W-1
T1IP2
R/W-0
T1IP1
R/W-0
T1IP0
U-0
—
R/W-1
R/W-0
R/W-0
OC1IP2
OC1IP1
OC1IP0
bit 15
bit 8
U-0
—
R/W-1
IC1IP2
R/W-0
IC1IP1
R/W-0
IC1IP0
U-0
—
R/W-1
R/W-0
R/W-0
INT0IP2
INT0IP1
INT0IP0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
T1IP<2:0>: Timer1 Interrupt Priority bits
bit 14-12
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
OC1IP<2:0>: Output Compare Channel 1 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
IC1IP<2:0>: Input Capture Channel 1 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
INT0IP<2:0>: External Interrupt 0 Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
2008-2014 Microchip Technology Inc.
DS70000318G-page 119
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-20: IPC1: INTERRUPT PRIORITY CONTROL REGISTER 1
U-0
—
R/W-1
T2IP2
R/W-0
T2IP1
R/W-0
T2IP0
U-0
—
R/W-1
R/W-0
R/W-0
OC2IP2
OC2IP1
OC2IP0
bit 15
bit 8
U-0
—
R/W-1
IC2IP2
R/W-0
IC2IP1
R/W-0
IC2IP0
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
T2IP<2:0>: Timer2 Interrupt Priority bits
bit 14-12
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
OC2IP<2:0>: Output Compare Channel 2 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
IC2IP<2:0>: Input Capture Channel 2 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
DS70000318G-page 120
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-21: IPC2: INTERRUPT PRIORITY CONTROL REGISTER 2
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
U1RXIP2
U1RXIP1
U1RXIP0
SPI1IP2
SPI1IP1
SPI1IP0
bit 15
bit 8
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
R/W-1
T3IP2
R/W-0
T3IP1
R/W-0
T3IP0
SPI1EIP2
SPI1EIP1
SPI1EIP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
Unimplemented: Read as ‘0’
bit 14-12
U1RXIP<2:0>: UART1 Receiver Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
SPI1IP<2:0>: SPI1 Event Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
SPI1EIP<2:0>: SPI1 Error Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
T3IP<2:0>: Timer3 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
2008-2014 Microchip Technology Inc.
DS70000318G-page 121
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-22: IPC3: INTERRUPT PRIORITY CONTROL REGISTER 3
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
R/W-1
ADIP2
R/W-0
ADIP1
R/W-0
ADIP0
U-0
—
R/W-1
R/W-0
R/W-0
U1TXIP2
U1TXIP1
U1TXIP0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-7
bit 6-4
Unimplemented: Read as ‘0’
ADIP<2:0>: ADC1 Conversion Complete Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
U1TXIP<2:0>: UART1 Transmitter Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
DS70000318G-page 122
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-23: IPC4: INTERRUPT PRIORITY CONTROL REGISTER 4
U-0
—
R/W-1
CNIP2
R/W-0
CNIP1
R/W-0
CNIP0
U-0
—
R/W-1
R/W-0
R/W-0
AC1IP2
AC1IP1
AC1IP0
bit 15
bit 8
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
MI2C1IP2
MI2C1IP1
MI2C1IP0
SI2C1IP2
SI2C1IP1
SI2C1IP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
Unimplemented: Read as ‘0’
bit 14-12
CNIP<2:0>: Change Notification Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
AC1IP<2:0>: Analog Comparator 1 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
MI2C1IP<2:0>: I2C1 Master Events Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
SI2C1IP<2:0>: I2C1 Slave Events Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
2008-2014 Microchip Technology Inc.
DS70000318G-page 123
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-24: IPC5: INTERRUPT PRIORITY CONTROL REGISTER 5
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-1
R/W-0
R/W-0
INT1IP2
INT1IP1
INT1IP0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-3
bit 2-0
Unimplemented: Read as ‘0’
INT1IP<2:0>: External Interrupt 1 Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
REGISTER 7-25: IPC7: INTERRUPT PRIORITY CONTROL REGISTER 7
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
bit 0
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
INT2IP2
INT2IP1
INT2IP0
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-7
bit 6-4
Unimplemented: Read as ‘0’
INT2IP<2:0>: External Interrupt 2 Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
DS70000318G-page 124
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-26: IPC14: INTERRUPT PRIORITY CONTROL REGISTER 14
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
bit 0
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
PSEMIP2
PSEMIP1
PSEMIP0
bit 7
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15-7
bit 6-4
Unimplemented: Read as ‘0’
PSEMIP<2:0>: PWM Special Event Match Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
REGISTER 7-27: IPC16: INTERRUPT PRIORITY CONTROL REGISTER 16
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
bit 0
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U1EIP2
U1EIP1
U1EIP0
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-7
bit 6-4
Unimplemented: Read as ‘0’
U1EIP<2:0>: UART1 Error Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3-0
Unimplemented: Read as ‘0’
2008-2014 Microchip Technology Inc.
DS70000318G-page 125
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-28: IPC23: INTERRUPT PRIORITY CONTROL REGISTER 23
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
PWM2IP2
PWM2IP1
PWM2IP0
PWM1IP2
PWM1IP1
PWM1IP0
bit 15
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
Unimplemented: Read as ‘0’
bit 14-12
PWM2IP<2:0>: PWM2 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
PWM1IP<2:0>: PWM1 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 7-0
Unimplemented: Read as ‘0’
DS70000318G-page 126
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-29: IPC24: INTERRUPT PRIORITY CONTROL REGISTER 24
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
PWM4IP2
PWM4IP1
PWM4IP0
PWM3IP2
PWM3IP1
PWM3IP0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15-7
bit 6-4
Unimplemented: Read as ‘0’
PWM4IP<2:0>: PWM4 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
PWM3IP<2:0>: PWM3 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
2008-2014 Microchip Technology Inc.
DS70000318G-page 127
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-30: IPC25: INTERRUPT PRIORITY CONTROL REGISTER 25
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
AC2IP2
AC2IP1
AC2IP0
bit 15
bit 8
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
AC2IP<2:0>: Analog Comparator 2 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 11-01
Unimplemented: Read as ‘0’
DS70000318G-page 128
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-31: IPC26: INTERRUPT PRIORITY CONTROL REGISTER 26
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
AC4IP2
AC4IP1
AC4IP0
AC3IP2
AC3IP1
AC3IP0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-7
bit 6-4
Unimplemented: Read as ‘0’
AC4IP<2:0>: Analog Comparator 4 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
AC3IP<2:0>: Analog Comparator 3 Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
2008-2014 Microchip Technology Inc.
DS70000318G-page 129
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-32: IPC27: INTERRUPT PRIORITY CONTROL REGISTER 27
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
ADCP0IP0
bit 8
ADCP1IP2
ADCP1IP1 ADCP1IP0
ADCP0IP2
ADCP0IP1
bit 15
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
Unimplemented: Read as ‘0’
bit 14-12
ADCP1IP<2:0>: ADC Pair 1 Conversion Done Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
ADCP0IP<2:0>: ADC Pair 0 Conversion Done Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 7-0
Unimplemented: Read as ‘0’
DS70000318G-page 130
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-33: IPC28: INTERRUPT PRIORITY CONTROL REGISTER 28
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
ADCP4IP0
bit 8
ADCP5IP2
ADCP5IP1 ADCP5IP0
ADCP4IP2
ADCP4IP1
bit 15
U-0
—
R/W-1
R/W-0
R/W-0
U-0
—
R/W-1
R/W-0
R/W-0
ADCP2IP0
bit 0
ADCP3IP2
ADCP3IP1 ADCP3IP0
ADCP2IP2
ADCP2IP1
bit 7
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
Unimplemented: Read as ‘0’
bit 14-12
ADCP5IP<2:0>: ADC Pair 5 Conversion Done Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 11
Unimplemented: Read as ‘0’
bit 10-8
ADCP4IP<2:0>: ADC Pair 4 Conversion Done Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 7
Unimplemented: Read as ‘0’
bit 6-4
ADCP3IP<2:0>: ADC Pair 3 Conversion Done Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
ADCP2IP<2:0>: ADC Pair 2 Conversion Done Interrupt Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
2008-2014 Microchip Technology Inc.
DS70000318G-page 131
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-34: IPC29: INTERRUPT PRIORITY CONTROL REGISTER 29
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-1
R/W-0
R/W-0
ADCP6IP0
bit 0
ADCP6IP2
ADCP6IP1
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-3
bit 2-0
Unimplemented: Read as ‘0’
ADCP6IP<2:0>: ADC Pair 6 Conversion Done Interrupt 1 Priority bits
111= Interrupt is Priority 7 (highest priority interrupt)
•
•
•
001= Interrupt is Priority 1
000= Interrupt source is disabled
DS70000318G-page 132
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 7-35: INTTREG: INTERRUPT CONTROL AND STATUS REGISTER
U-0
—
U-0
—
U-0
—
U-0
—
R-0
R-0
R-0
R-0
ILR3
ILR2
ILR1
ILR0
bit 15
bit 8
U-0
—
R-0
R-0
R-0
R-0
R-0
R-0
R-0
VECNUM6
VECNUM5 VECNUM4 VECNUM3
VECNUM2
VECNUM1
VECNUM0
bit 0
bit 7
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15-12
bit 11-8
Unimplemented: Read as ‘0’
ILR<3:0>: New CPU Interrupt Priority Level bits
1111= CPU Interrupt Priority Level is 15
•
•
•
0001= CPU Interrupt Priority Level is 1
0000= CPU Interrupt Priority Level is 0
bit 7
Unimplemented: Read as ‘0’
bit 6-0
VECNUM<6:0>: Vector Number of Pending Interrupt bits
0111111= Interrupt vector pending is Number 135
•
•
•
0000001= Interrupt vector pending is Number 9
0000000= Interrupt vector pending is Number 8
2008-2014 Microchip Technology Inc.
DS70000318G-page 133
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
7.4.3
TRAP SERVICE ROUTINE
7.4
Interrupt Setup Procedures
A Trap Service Routine (TSR) is coded like an ISR,
except that the appropriate trap status flag in the
INTCON1 register must be cleared to avoid re-entry
into the TSR.
7.4.1
INITIALIZATION
Complete the following steps to configure an interrupt
source at initialization:
1. Set the NSTDIS bit (INTCON1<15>) if nested
interrupts are not desired.
7.4.4
INTERRUPT DISABLE
The following steps outline the procedure to disable all
user interrupts:
2. Select the user-assigned priority level for the
interrupt source by writing the control bits in the
appropriate IPCx register. The priority level will
depend on the specific application and type of
interrupt source. If multiple priority levels are not
desired, the IPCx register control bits for all
enabled interrupt sources can be programmed
to the same non-zero value.
1. Push the current SR value onto the software
stack using the PUSHinstruction.
2. Force the CPU to Priority Level 7 by inclusive
ORing the value 0xE0 with SRL.
To enable user interrupts, the POP instruction can be
used to restore the previous SR value.
Note: At a device Reset, the IPCx registers are
initialized such that all user interrupt
sources are assigned to Priority Level 4.
Note:
Only user interrupts with a priority level of 7
or lower can be disabled. Trap sources
(level 8-level 15) cannot be disabled.
3. Clear the interrupt flag status bit associated with
the peripheral in the associated IFSx register.
The DISI instruction provides a convenient way to
disable interrupts of Priority Levels 1-6 for a fixed
period of time. Level 7 interrupt sources are not
disabled by the DISI instruction.
4. Enable the interrupt source by setting the
interrupt enable control bit associated with the
source in the appropriate IECx register.
7.4.2
INTERRUPT SERVICE ROUTINE
The method used to declare an ISR and initialize the
IVT with the correct vector address depends on the
programming language (C or assembler) and the
language development toolsuite used to develop the
application.
In general, the user application must clear the interrupt
flag in the appropriate IFSx register for the source of
interrupt that the ISR handles. Otherwise, program will
re-enter the ISR immediately after exiting the routine. If
the ISR is coded in assembly language, it must be
terminated using a RETFIE instruction to unstack the
saved PC value, SRL value and old CPU priority level.
DS70000318G-page 134
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The oscillator system provides:
8.0 OSCILLATORCONFIGURATION
• External and internal oscillator options as
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a compre-
hensive reference source. To complement
the information in this data sheet, refer to
“Oscillator (Part IV)” (DS70307) in the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
clock sources
• An on-chip Phase-Locked Loop (PLL) to scale the
internal operating frequency to the required system
clock frequency
• An internal FRC oscillator that can also be used with
the PLL, thereby allowing full-speed operation
without any external clock generation hardware
• Clock switching between various clock sources
• Programmable clock postscaler for system power
savings
• A Fail-Safe Clock Monitor (FSCM) that detects clock
failure and takes fail-safe measures
• A Clock Control register (OSCCON)
• Nonvolatile Configuration bits for main oscillator
selection
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
• Auxiliary PLL for ADC and PWM
A simplified diagram of the oscillator system is shown
in Figure 8-1.
FIGURE 8-1:
OSCILLATOR SYSTEM DIAGRAM
Primary Oscillator
POSCCLK
DOZE<2:0>
OSC1
XT, HS, EC
S2
XTPLL, HSPLL,
S3
R(2)
ECPLL, FRCPLL
(3)
(3)
PLL(1)
F
CY
S1/S3
S1
(1)
FVCO
OSC2
POSCMD<1:0>
F
P
FRCDIVN
FRC
Oscillator
FRCCLK
S7
÷ 2
FOSC
FRCDIV<2:0>
TUN<5:0>
FRCDIV16
FRC
÷ 16
S6
S0
LPRC
LPRC
Oscillator
S5
Reference Clock Generation
POSCCLK
Clock Switch
NOSC<2:0>
Reset
Clock Fail
S7
REFCLKO
÷ N
FOSC
RPx
FNOSC<2:0>
WDT, PWRT,
FSCM
ROSEL RODIV<3:0>
Auxiliary Clock Generation
FRCCLK
(1)
FVCO
To PWM/ADC(1)
APLL(1)
x16
POSCCLK
ACLK
÷ N
ASRCSEL
FRCSEL
ENAPLL
SELACLK
APSTSCLR<2:0>
Note 1: See Section 8.1.3 “PLL Configuration” and Section 8.2 “Auxiliary Clock Generation” for configuration restrictions.
2: If the oscillator is used with XT or HS modes, an external parallel resistor with the value of 1 M must be connected.
3: The term, FP, refers to the clock source for all the peripherals, while FCY refers to the clock source for the CPU. Throughout this doc-
ument, FCY and FP are used interchangeably, except in the case of Doze mode. FP and FCY will be different when Doze mode is used
in any ratio other than 1:1, which is the default.
2008-2014 Microchip Technology Inc.
DS70000318G-page 135
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
output frequencies for device operation. PLL
configuration is described in Section 8.1.3 “PLL
Configuration”.
8.1
CPU Clocking System
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices provide six system clock options:
The FRC frequency depends on the FRC accuracy
(see Table 24-20) and the value of the FRC Oscillator
Tuning register (see Register 8-4).
• Fast RC (FRC) Oscillator
• FRC Oscillator with PLL
• Primary (XT, HS or EC) Oscillator
• Primary Oscillator with PLL
• Low-Power RC (LPRC) Oscillator
• FRC Oscillator with Postscaler
8.1.2
SYSTEM CLOCK SELECTION
The oscillator source used at a device Power-on
Reset event is selected using Configuration bit
settings. The Oscillator Configuration bit settings are
located in the Configuration registers in the program
memory. (Refer to Section 21.1 “Configuration Bits”
for further details.) The Initial Oscillator Selection Con-
figuration bits, FNOSC<2:0> (FOSCSEL<2:0>), and the
Primary Oscillator Mode Select Configuration bits,
POSCMD<1:0> (FOSC<1:0>), select the oscillator
source that is used at a Power-on Reset. The FRC
primary oscillator is the default (unprogrammed)
selection.
8.1.1
SYSTEM CLOCK SOURCES
The Fast RC (FRC) internal oscillator runs at a nominal
frequency of 7.37 MHz. User software can tune the
FRC frequency. User software can optionally specify a
factor (ranging from 1:2 to 1:256) by which the FRC
clock frequency is divided. This factor is selected using
the FRCDIV<2:0> (CLKDIV<10:8>) bits.
The primary oscillator can use one of the following as
its clock source:
The Configuration bits allow users to choose among
12 different clock modes, shown in Table 8-1.
• XT (Crystal): Crystals and ceramic resonators in
the range of 3 MHz to 10 MHz. The crystal is
connected to the OSC1 and OSC2 pins.
The output of the oscillator (or the output of the PLL if
a PLL mode has been selected), FOSC, is divided by 2
to generate the device instruction clock (FCY) and the
peripheral clock time base (FP). FCY defines the
operating speed of the device and speeds up to
40 MHz are supported by the dsPIC33FJ06GS101/
X02 and dsPIC33FJ16GSX02/X04 architecture.
• HS (High-Speed Crystal): Crystals in the range of
10 MHz to 40 MHz. The crystal is connected to
the OSC1 and OSC2 pins.
• EC (External Clock): The external clock signal is
directly applied to the OSC1 pin.
The LPRC internal oscIllator runs at a nominal
frequency of 32.768 kHz. It is also used as a reference
clock by the Watchdog Timer (WDT) and Fail-Safe
Clock Monitor (FSCM).
Instruction execution speed or device operating
frequency, FCY, is given by Equation 8-1.
EQUATION 8-1:
DEVICE OPERATING
FREQUENCY
The clock signals generated by the FRC and primary
oscillators can be optionally applied to an on-chip
Phase-Locked Loop (PLL) to provide a wide range of
FCY = FOSC/2
TABLE 8-1:
CONFIGURATION BIT VALUES FOR CLOCK SELECTION
Oscillator Mode Oscillator Source POSCMD<1:0> FNOSC<2:0> See Notes
Fast RC Oscillator with Divide-by-N (FRCDIVN)
Fast RC Oscillator with Divide-by-16 (FRCDIV16)
Low-Power RC Oscillator (LPRC)
Reserved
Internal
Internal
Internal
Reserved
Primary
Primary
Primary
Primary
Primary
Primary
Internal
Internal
xx
xx
xx
xx
10
01
00
10
01
00
xx
xx
111
110
101
100
011
011
011
010
010
010
001
000
1, 2
1
1
—
—
—
1
Primary Oscillator (HS) with PLL (HSPLL)
Primary Oscillator (XT) with PLL (XTPLL)
Primary Oscillator (EC) with PLL (ECPLL)
Primary Oscillator (HS)
—
—
1
Primary Oscillator (XT)
Primary Oscillator (EC)
Fast RC Oscillator with PLL (FRCPLL)
Fast RC Oscillator (FRC)
1
1
Note 1: OSC2 pin function is determined by the OSCIOFNC Configuration bit.
2: This is the default oscillator mode for an unprogrammed (erased) device.
DS70000318G-page 136
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
For a primary oscillator or FRC oscillator, output ‘FIN’,
the PLL output ‘FOSC’ is given by Equation 8-2.
8.1.3
PLL CONFIGURATION
The primary oscillator and internal FRC oscillator can
optionally use an on-chip PLL to obtain higher speeds
of operation. The PLL provides significant flexibility in
selecting the device operating speed. A block diagram
of the PLL is shown in Figure 8-2.
EQUATION 8-2:
FOSC CALCULATION
M
FOSC = FIN *
(N1*N2)
The output of the primary oscillator or FRC, denoted
as ‘FIN’, is divided down by a prescale factor (N1) of 2,
3, ... or 33 before being provided to the PLL’s Voltage
Controlled Oscillator (VCO). The input to the VCO
must be selected in the range of 0.8 MHz to 8 MHz.
The prescale factor ‘N1’ is selected using the
PLLPRE<4:0> bits (CLKDIV<4:0>).
For example, suppose a 10 MHz crystal is being used
with the selected oscillator mode of XT with PLL (see
Equation 8-3).
• If PLLPRE<4:0> = 0, then N1 = 2. This yields a
VCO input of 10/2 = 5 MHz, which is within the
acceptable range of 0.8-8 MHz.
• If PLLDIV<8:0> = 0x1E, then M = 32. This yields a
VCO output of 5 x 32 = 160 MHz, which is within
the 100-200 MHz ranged needed.
The PLL Feedback Divisor, selected using the
PLLDIV<8:0> bits (PLLFBD<8:0>), provides a factor, ‘M’,
by which the input to the VCO is multiplied. This factor
must be selected such that the resulting VCO output
frequency is in the range of 100 MHz to 200 MHz.
• If PLLPOST<1:0> = 0, then N2 = 2. This provides
a Fosc of 160/2 = 80 MHz. The resultant device
operating speed is 80/2 = 40 MIPS.
The VCO output is further divided by a postscale factor,
‘N2’. This factor is selected using the PLLPOST<1:0>
bits (CLKDIV<7:6>). ‘N2’ can be either 2, 4, or 8, and
must be selected such that the PLL output frequency
(FOSC) is in the range of 12.5 MHz to 80 MHz, which
generates device operating speeds of 6.25-40 MIPS.
EQUATION 8-3:
XT WITH PLL MODE
EXAMPLE
FOSC
1
2
10000000 * 32
FCY =
=
= 40 MIPS
(
)
2
2 * 2
FIGURE 8-2:
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 PLL BLOCK DIAGRAM
FVCO
0.8-8.0 MHz
Here(1)
12.5-80 MHz
Here(1)
100-200 MHz
Here(1)
Source (Crystal, External
Clock or Internal RC)
PLLPRE
VCO
PLLPOST
X
FOSC
PLLDIV
N2
N1
Divide-by-
2-33
Divide-by-
2, 4, 8
M
Divide-by-
2-513
Note 1: This frequency range must be satisfied at all times.
2008-2014 Microchip Technology Inc.
DS70000318G-page 137
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
8.2
Auxiliary Clock Generation
8.3
Reference Clock Generation
The auxiliary clock generation is used for a peripherals
that need to operate at a frequency unrelated to the
system clock such as a PWM or ADC.
The reference clock output logic provides the user with
the ability to output a clock signal based on the system
clock or the crystal oscillator on a device pin. The user
application can specify a wide range of clock scaling
prior to outputting the reference clock.
The primary oscillator and internal FRC oscillator
sources can be used with an auxiliary PLL to obtain the
auxiliary clock. The auxiliary PLL has a fixed 16x
multiplication factor.
The auxiliary clock has the following configuration
restrictions:
• For proper PWM operation, auxiliary clock genera-
tion must be configured for 120 MHz (see
Parameter OS56 in Table 24-18 in Section 24.0
“Electrical Characteristics”). If a slower frequency
is desired, the PWM Input Clock Prescaler (Divider)
Select bits (PCLKDIV<2:0>) should be used.
• To achieve 1.04 ns PWM resolution, the auxiliary
clock must use the 16x auxiliary PLL (APLL). All
other clock sources will have a minimum PWM
resolution of 8 ns.
• If the primary PLL is used as a source for the
auxiliary clock, the primary PLL should be config-
ured up to a maximum operation of 30 MIPS or
less
DS70000318G-page 138
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
8.4
Oscillator Control Registers
OSCCON: OSCILLATOR CONTROL REGISTER(1,2)
REGISTER 8-1:
U-0
—
R-0
R-0
R-0
U-0
—
R/W-y
NOSC2(3)
R/W-y
NOSC1(3)
R/W-y
NOSC0(3)
COSC2
COSC1
COSC0
bit 15
bit 8
R/W-0
R/W-0
R-0
U-0
—
R/C-0
CF
U-0
—
U-0
—
R/W-0
CLKLOCK
IOLOCK
LOCK
OSWEN
bit 7
bit 0
Legend:
y = Value set from Configuration bits on POR
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
Unimplemented: Read as ‘0’
bit 14-12
COSC<2:0>: Current Oscillator Selection bits (read-only)
111= Fast RC oscillator (FRC) with divide-by-n
110= Fast RC oscillator (FRC) with divide-by-16
101= Low-Power RC oscillator (LPRC)
100= Reserved
011= Primary oscillator (XT, HS, EC) with PLL
010= Primary oscillator (XT, HS, EC)
001= Fast RC oscillator (FRC) with PLL
000= Fast RC oscillator (FRC)
bit 11
Unimplemented: Read as ‘0’
bit 10-8
NOSC<2:0>: New Oscillator Selection bits(3)
111= Fast RC oscillator (FRC) with divide-by-n
110= Fast RC oscillator (FRC) with divide-by-16
101= Low-Power RC oscillator (LPRC)
100= Reserved
011= Primary oscillator (XT, HS, EC) with PLL
010= Primary oscillator (XT, HS, EC)
001= Fast RC oscillator (FRC) with PLL
000= Fast RC oscillator (FRC)
bit 7
CLKLOCK: Clock Lock Enable bit
If Clock Switching is Enabled and FSCM is Disabled, (FOSC<FCKSM> = 0b01):
1= Clock switching is disabled, system clock source is locked
0= Clock switching is enabled, system clock source can be modified by clock switching
bit 6
bit 5
bit 4
IOLOCK: Peripheral Pin Select Lock bit
1= Peripheral Pin Select is locked, write to Peripheral Pin Select registers not allowed
0= Peripheral Pin Select is not locked, write to Peripheral Pin Select registers allowed
LOCK: PLL Lock Status bit (read-only)
1= Indicates that PLL is in lock, or PLL start-up timer is satisfied
0= Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled
Unimplemented: Read as ‘0’
Note 1: Writes to this register require an unlock sequence. Refer to “Oscillator (Part IV)” (DS70307) in the
“dsPIC33F/PIC24H Family Reference Manual” (available from the Microchip web site) for details.
2: This register is reset only on a Power-on Reset (POR).
3: Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.
This applies to clock switches in either direction. In these instances, the application must switch to FRC
mode as a transition clock source between the two PLL modes.
2008-2014 Microchip Technology Inc.
DS70000318G-page 139
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 8-1:
OSCCON: OSCILLATOR CONTROL REGISTER(1,2) (CONTINUED)
bit 3
CF: Clock Fail Detect bit (read/clear by application)
1= FSCM has detected clock failure
0= FSCM has not detected clock failure
bit 2-1
bit 0
Unimplemented: Read as ‘0’
OSWEN: Oscillator Switch Enable bit
1= Request oscillator switch to selection specified by NOSC<2:0> bits
0= Oscillator switch is complete
Note 1: Writes to this register require an unlock sequence. Refer to “Oscillator (Part IV)” (DS70307) in the
“dsPIC33F/PIC24H Family Reference Manual” (available from the Microchip web site) for details.
2: This register is reset only on a Power-on Reset (POR).
3: Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.
This applies to clock switches in either direction. In these instances, the application must switch to FRC
mode as a transition clock source between the two PLL modes.
DS70000318G-page 140
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 8-2:
CLKDIV: CLOCK DIVISOR REGISTER(1)
R/W-0
ROI
R/W-0
R/W-1
R/W-1
R/W-0
DOZEN(2)
R/W-0
R/W-0
R/W-0
DOZE2
DOZE1
DOZE0
FRCDIV2
FRCDIV1
FRCDIV0
bit 15
bit 8
R/W-0
R/W-1
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PLLPOST1
bit 7
PLLPOST0
PLLPRE4
PLLPRE3
PLLPRE2
PLLPRE1
PLLPRE0
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
ROI: Recover on Interrupt bit
1= Interrupts will clear the DOZEN bit and the processor clock/peripheral clock ratio is set to 1:1
0= Interrupts have no effect on the DOZEN bit
bit 14-12
DOZE<2:0>: Processor Clock Reduction Select bits
111= FCY/128
110= FCY/64
101= FCY/32
100= FCY/16
011= FCY/8 (default)
010= FCY/4
001= FCY/2
000= FCY/1
bit 11
DOZEN: Doze Mode Enable bit(2)
1= DOZE<2:0> field specifies the ratio between the peripheral clocks and the processor clocks
0= Processor clock/peripheral clock ratio forced to 1:1
bit 10-8
FRCDIV<2:0>: Internal Fast RC Oscillator Postscaler bits
111= FRC divide-by-256
110= FRC divide-by-64
101= FRC divide-by-32
100= FRC divide-by-16
011= FRC divide-by-8
010= FRC divide-by-4
001= FRC divide-by-2
000= FRC divide-by-1 (default)
bit 7-6
PLLPOST<1:0>: PLL VCO Output Divider Select bits (also denoted as ‘N2’, PLL postscaler)
11= Output/8
10= Reserved
01= Output/4 (default)
00= Output/2
bit 5
Unimplemented: Read as ‘0’
bit 4-0
PLLPRE<4:0>: PLL Phase Detector Input Divider bits (also denoted as ‘N1’, PLL prescaler)
11111= Input/33
•
•
•
00001= Input/3
00000= Input/2 (default)
Note 1: This register is reset only on a Power-on Reset (POR).
2: This bit is cleared when the ROI bit is set and an interrupt occurs.
2008-2014 Microchip Technology Inc.
DS70000318G-page 141
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 8-3:
PLLFBD: PLL FEEDBACK DIVISOR REGISTER(1)
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
PLLDIV<8>
bit 8
bit 15
R/W-0
bit 7
R/W-0
R/W-1
R/W-1
R/W-0
R/W-0
R/W-0
R/W-0
bit 0
PLLDIV<7:0>
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-9
bit 8-0
Unimplemented: Read as ‘0’
PLLDIV<8:0>: PLL Feedback Divisor bits (also denoted as ‘M’, PLL multiplier)
111111111= 513
•
•
•
000110000= 50 (default)
•
•
•
000000010= 4
000000001= 3
000000000= 2
Note 1: This register is reset only on a Power-on Reset (POR).
DS70000318G-page 142
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 8-4:
OSCTUN: FRC OSCILLATOR TUNING REGISTER(1)
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TUN<5:0>(2)
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-6
bit 5-0
Unimplemented: Read as ‘0’
TUN<5:0>: FRC Oscillator Tuning bits(2)
011111= Center frequency + 11.6% (8.2268 MHz)
011110= Center frequency + 11.2% (8.1992 MHz)
•
•
•
000001= Center frequency + 0.375% (7.3976 MHz)
000000= Center frequency (7.37 MHz nominal)
111111= Center frequency – 0.375% (7.2594 MHz)
•
•
•
100001= Center frequency – 11.6% (6.5132 MHz)
000000= Center frequency – 12% (6.4856 MHz)
Note 1: This register is reset only on a Power-on Reset (POR).
2: OSCTUN functionality has been provided to help customers compensate for temperature effects on the
FRC frequency over a wide range of temperatures. The tuning step-size is an approximation and is neither
characterized nor tested.
2008-2014 Microchip Technology Inc.
DS70000318G-page 143
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 8-5:
ACLKCON: AUXILIARY CLOCK DIVISOR CONTROL REGISTER(1)
R/W-0
ENAPLL
bit 15
R-0
R/W-1
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
APLLCK
SELACLK
APSTSCLR2 APSTSCLR1 APSTSCLR0
bit 0
R/W-0
ASRCSEL
bit 7
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
FRCSEL
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
bit 14
bit 13
ENAPLL: Auxiliary PLL Enable bit
1= APLL is enabled
0= APLL is disabled
APLLCK: APLL Locked Status bit (read-only)
1= Indicates that auxiliary PLL is in lock
0= Indicates that auxiliary PLL is not in lock
SELACLK: Select Auxiliary Clock Source for Auxiliary Clock Divider bit
1= Auxiliary oscillators provides the source clock for auxiliary clock divider
0= Primary PLL (FVCO) provides the source clock for auxiliary clock divider
bit 12-11
bit 10-8
Unimplemented: Read as ‘0’
APSTSCLR<2:0>: Auxiliary Clock Output Divider bits
111= Divided by 1
110= Divided by 2
101= Divided by 4
100= Divided by 8
011= Divided by 16
010= Divided by 32
001= Divided by 64
000= Divided by 256
bit 7
ASRCSEL: Select Reference Clock Source for Auxiliary Clock bit
1= Primary oscillator is the clock source
0= No clock input is selected
bit 6
FRCSEL: Select Reference Clock Source for Auxiliary PLL bit
1= Select FRC clock for auxiliary PLL
0= Input clock source is determined by ASRCSEL bit setting
bit 5-0
Unimplemented: Read as ‘0’
Note 1: This register is reset only on a Power-on Reset (POR).
DS70000318G-page 144
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 8-6:
REFOCON: REFERENCE OSCILLATOR CONTROL REGISTER
R/W-0
ROON
U-0
—
R/W-0
R/W-0
R/W-0
RODIV3(1)
R/W-0
RODIV2(1)
R/W-0
RODIV1(1)
R/W-0
RODIV0(1)
bit 8
ROSSLP
ROSEL
bit 15
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
ROON: Reference Oscillator Output Enable bit
1= Reference oscillator output is enabled on the REFCLK0 pin(2)
0= Reference oscillator output is disabled
bit 14
bit 13
Unimplemented: Read as ‘0’
ROSSLP: Reference Oscillator Run in Sleep bit
1= Reference oscillator output continues to run in Sleep
0= Reference oscillator output is disabled in Sleep
bit 12
ROSEL: Reference Oscillator Source Select bit
1= Oscillator crystal is used as the reference clock
0= System clock is used as the reference clock
bit 11-8
RODIV<3:0>: Reference Oscillator Divider bits(1)
1111= Reference clock divided by 32,768
1110= Reference clock divided by 16,384
1101= Reference clock divided by 8,192
1100= Reference clock divided by 4,096
1011= Reference clock divided by 2,048
1010= Reference clock divided by 1,024
1001= Reference clock divided by 512
1000= Reference clock divided by 256
0111= Reference clock divided by 128
0110= Reference clock divided by 64
0101= Reference clock divided by 32
0100= Reference clock divided by 16
0011= Reference clock divided by 8
0010= Reference clock divided by 4
0001= Reference clock divided by 2
0000= Reference clock
bit 7-0
Unimplemented: Read as ‘0’
Note 1: The reference oscillator output must be disabled (ROON = 0) before writing to these bits.
2: This pin is remappable. Refer to Section 10.6 “Peripheral Pin Select” for more information.
2008-2014 Microchip Technology Inc.
DS70000318G-page 145
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
2. If a valid clock switch has been initiated, the LOCK
8.5
Clock Switching Operation
(OSCCON<5>) and the CF (OSCCON<3>) status
bits are cleared.
Users can switch applications among any of the four
clock sources (primary, LP, FRC and LPRC) under
software control at any time. To limit the possible side
effects of this flexibility, dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 devices have a safeguard
lock built into the switch process.
3. The new oscillator is turned on by the hardware if
it is not currently running. If a crystal oscillator
must be turned on, the hardware waits until the
Oscillator Start-up Timer (OST) expires. If the new
source is using the PLL, the hardware waits until a
PLL lock is detected (LOCK = 1).
Note:
Primary oscillator mode has three different
submodes (XT, HS and EC), which are
determined by the POSCMD<1:0>
Configuration bits. While an application
can switch to and from primary oscillator
mode in software, it cannot switch among
the different primary submodes without
reprogramming the device.
4. The hardware waits for 10 clock cycles from the
new clock source and then performs the clock
switch.
5. The hardware clears the OSWEN bit to indicate a
successful clock transition. In addition, the
NOSC<2:0> bit values are transferred to the
COSC<2:0> status bits.
6. The old clock source is turned off at this time, with
the exception of LPRC (if WDT or FSCM are
enabled).
8.5.1
ENABLING CLOCK SWITCHING
To enable clock switching, the FCKSM1 Configuration
bit in the Configuration register must be programmed to
‘0’. (Refer to Section 21.1 “Configuration Bits” for
further details.) If the FCKSM1 Configuration bit is
unprogrammed (‘1’), the clock switching function and
Fail-Safe Clock Monitor function are disabled. This is
the default setting.
Note 1: The processor continues to execute code
throughout the clock switching sequence.
Timing-sensitive code should not be
executed during this time.
2: Direct clock switches between any pri-
mary oscillator mode with PLL and
FRCPLL mode are not permitted. This
applies to clock switches in either direc-
tion. In these instances, the application
must switch to FRC mode as a transition
clock source between the two PLL modes.
3: Refer to “Oscillator (Part IV)”
(DS70307) in the “dsPIC33F/PIC24H
Family Reference Manual” for details.
The NOSC<2:0> control bits (OSCCON<10:8>) do
not control the clock selection when clock switching
is disabled. However, the COSC<2:0> bits
(OSCCON<14:12>) reflect the clock source selected by
the FNOSCx Configuration bits.
The OSWEN control bit (OSCCON<0>) has no effect
when clock switching is disabled. It is held at ‘0’ at all
times.
8.5.2
OSCILLATOR SWITCHING SEQUENCE
8.6
Fail-Safe Clock Monitor (FSCM)
To perform a clock switch, the following basic sequence
is required:
The Fail-Safe Clock Monitor (FSCM) allows the device
to continue to operate even in the event of an oscillator
failure. The FSCM function is enabled by programming.
If the FSCM function is enabled, the LPRC internal
oscillator runs at all times (except during Sleep mode)
and is not subject to control by the Watchdog Timer.
1. If required, read the COSC<2:0> bits to determine
the current oscillator source.
2. Perform the unlock sequence to allow a write to
the OSCCON register high byte.
3. Write the appropriate value to the NOSC<2:0>
control bits for the new oscillator source.
During an oscillator failure, the FSCM generates a
clock failure trap event and switches the system clock
over to the FRC oscillator. Then, the application
program can either attempt to restart the oscillator or
execute a controlled shutdown. The trap can be treated
as a Warm Reset by simply loading the Reset address
into the oscillator fail trap vector.
4. Perform the unlock sequence to allow a write to
the OSCCON register low byte.
5. Set the OSWEN bit to initiate the oscillator switch.
After the basic sequence is completed, the system
clock hardware responds as follows:
If the PLL multiplier is used to scale the system clock,
the internal FRC is also multiplied by the same factor
on clock failure. Essentially, the device switches to
FRC with PLL on a clock failure.
1. The clock switching hardware compares the
COSC<2:0> status bits with the new value of the
NOSC<2:0> control bits. If they are the same,
the clock switch is a redundant operation. In this
case, the OSWEN bit is cleared automatically
and the clock switch is aborted.
DS70000318G-page 146
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
9.2
Instruction-Based Power-Saving
Modes
9.0
POWER-SAVING FEATURES
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “Watchdog Timer and
Power-Saving Modes” (DS70196) in
the “dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices have two special power-saving modes that
are entered through the execution of a special PWRSAV
instruction. Sleep mode stops clock operation and halts all
code execution. Idle mode halts the CPU and code
execution, but allows peripheral modules to continue
operation. The assembler syntax of the PWRSAV
instruction is shown in Example 9-1.
Note: SLEEP_MODE and IDLE_MODE are
constants defined in the assembler
include file for the selected device.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
Sleep and Idle modes can be exited as a result of an
enabled interrupt, WDT time-out or a device Reset. When
the device exits these modes, it is said to wake-up.
9.2.1
SLEEP MODE
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices provide the ability to manage power
consumption by selectively managing clocking to the
CPU and the peripherals. In general, a lower clock
frequency and a reduction in the number of circuits
being clocked constitutes lower consumed power.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices can manage power consumption in four
different ways:
The following occur in Sleep mode:
• The system clock source is shut down. If an
on-chip oscillator is used, it is turned off
• The device current consumption is reduced to a
minimum, provided that no I/O pin is sourcing
current
• The Fail-Safe Clock Monitor does not operate,
since the system clock source is disabled
• The LPRC clock continues to run in Sleep mode if
the WDT is enabled
• Clock Frequency
• Instruction-Based Sleep and Idle modes
• Software-Controlled Doze mode
• Selective Peripheral Control in Software
• The WDT, if enabled, is automatically cleared
prior to entering Sleep mode
• Some device features or peripherals may continue
to operate. This includes the items such as the
Input Change Notification on the I/O ports or
peripherals that use an external clock input.
Combinations of these methods can be used to
selectively tailor an application’s power consumption
while still maintaining critical application features, such
as timing-sensitive communications.
• Any peripheral that requires the system clock
source for its operation is disabled
9.1
Clock Frequency and Clock
Switching
The device will wake-up from Sleep mode on any of
these events:
The dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices allow a wide range of clock frequencies to
be selected under application control. If the system
clock configuration is not locked, users can choose
low-power or high-precision oscillators by simply
changing the NOSC<2:0> bits (OSCCON<10:8>).
The process of changing a system clock during
operation, as well as limitations to the process, are
discussed in more detail in Section 8.0 “Oscillator
Configuration”.
• Any interrupt source that is individually enabled
• Any form of device Reset
• A WDT time-out
On wake-up from Sleep mode, the processor restarts
with the same clock source that was active when Sleep
mode was entered.
EXAMPLE 9-1:
PWRSAV INSTRUCTION SYNTAX
PWRSAV #SLEEP_MODE
PWRSAV #IDLE_MODE
; Put the device into SLEEP mode
; Put the device into IDLE mode
2008-2014 Microchip Technology Inc.
DS70000318G-page 147
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Doze mode is enabled by setting the DOZEN bit
(CLKDIV<11>). The ratio between peripheral and core
clock speed is determined by the DOZE<2:0> bits
(CLKDIV<14:12>). There are eight possible configura-
tions, from 1:1 to 1:128, with 1:1 being the default
setting.
9.2.2
IDLE MODE
The following occur in Idle mode:
• The CPU stops executing instructions
• The WDT is automatically cleared
• The system clock source remains active. By
default, all peripheral modules continue to operate
normally from the system clock source, but can
also be selectively disabled (see Section 9.4
“Peripheral Module Disable”).
Programs can use Doze mode to selectively reduce
power consumption in event-driven applications. This
allows clock-sensitive functions, such as synchronous
communications, to continue without interruption while
the CPU idles, waiting for something to invoke an
interrupt routine. An automatic return to full-speed CPU
operation on interrupts can be enabled by setting the
ROI bit (CLKDIV<15>). By default, interrupt events
have no effect on Doze mode operation.
• If the WDT or FSCM is enabled, the LPRC also
remains active
The device will wake-up from Idle mode on any of these
events:
• Any interrupt that is individually enabled
• Any device Reset
• A WDT time-out
For example, suppose the device is operating at
20 MIPS and the CAN module has been configured for
500 kbps based on this device operating speed. If the
device is placed in Doze mode with a clock frequency
ratio of 1:4, the CAN module continues to communicate
at the required bit rate of 500 kbps, but the CPU now
starts executing instructions at a frequency of 5 MIPS.
On wake-up from Idle mode, the clock is reapplied to
the CPU and instruction execution will begin (2-4 clock
cycles later), starting with the instruction following the
PWRSAVinstruction, or the first instruction in the ISR.
9.2.3
INTERRUPTS COINCIDENT WITH
POWER SAVE INSTRUCTIONS
9.4
Peripheral Module Disable
The Peripheral Module Disable (PMD) registers
provide a method to disable a peripheral module by
stopping all clock sources supplied to that module.
When a peripheral is disabled using the appropriate
PMD control bit, the peripheral is in a minimum power
consumption state. The control and status registers
associated with the peripheral are also disabled, so
writes to those registers will have no effect and read
values will be invalid.
Any interrupt that coincides with the execution of a
PWRSAV instruction is held off until entry into Sleep or
Idle mode has completed. The device then wakes up
from Sleep or Idle mode.
9.3
Doze Mode
The preferred strategies for reducing power
consumption are changing clock speed and invoking
one of the power-saving modes. In some
circumstances, this may not be practical. For example,
it may be necessary for an application to maintain
uninterrupted synchronous communication, even while
it is doing nothing else. Reducing system clock speed
can introduce communication errors, while using a
power-saving mode can stop communications
completely.
A peripheral module is enabled only if both the
associated bit in the PMD register is cleared and the
peripheral is supported by the specific dsPIC® DSC
variant. If the peripheral is present in the device, it is
enabled in the PMD register by default.
Note:
If a PMD bit is set, the corresponding
module is disabled after a delay of one
instruction cycle. Similarly, if a PMD bit is
cleared, the corresponding module is
enabled after a delay of one instruction
cycle (assuming the module control regis-
ters are already configured to enable
module operation).
Doze mode is a simple and effective alternative method
to reduce power consumption while the device is still
executing code. In this mode, the system clock
continues to operate from the same source and at the
same speed. Peripheral modules continue to be
clocked at the same speed, while the CPU clock speed
is reduced. Synchronization between the two clock
domains is maintained, allowing the peripherals to
access the SFRs while the CPU executes code at a
slower rate.
DS70000318G-page 148
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 9-1:
PMD1: PERIPHERAL MODULE DISABLE CONTROL REGISTER 1
U-0
—
U-0
—
R/W-0
T3MD
R/W-0
T2MD
R/W-0
T1MD
U-0
—
R/W-0
PWMMD(1)
U-0
—
bit 15
bit 8
R/W-0
I2C1MD
bit 7
U-0
—
R/W-0
U1MD
U-0
—
R/W-0
U-0
—
U-0
—
R/W-0
SPI1MD
ADCMD
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13
Unimplemented: Read as ‘0’
T3MD: Timer3 Module Disable bit
1= Timer3 module is disabled
0= Timer3 module is enabled
bit 12
bit 11
T2MD: Timer2 Module Disable bit
1= Timer2 module is disabled
0= Timer2 module is enabled
T1MD: Timer1 Module Disable bit
1= Timer1 module is disabled
0= Timer1 module is enabled
bit 10
bit 9
Unimplemented: Read as ‘0’
PWMMD: PWM Module Disable bit(1)
1= PWM module is disabled
0= PWM module is enabled
bit 8
bit 7
Unimplemented: Read as ‘0’
I2C1MD: I2C1 Module Disable bit
1= I2C1 module is disabled
0= I2C1 module is enabled
bit 6
bit 5
Unimplemented: Read as ‘0’
U1MD: UART1 Module Disable bit
1= UART1 module is disabled
0= UART1 module is enabled
bit 4
bit 3
Unimplemented: Read as ‘0’
SPI1MD: SPI1 Module Disable bit
1= SPI1 module is disabled
0= SPI1 module is enabled
bit 2-1
bit 0
Unimplemented: Read as ‘0’
ADCMD: ADC Module Disable bit
1= ADC module is disabled
0= ADC module is enabled
Note 1: Once the PWM module is re-enabled (PWMMD is set to ‘1’ and then set to ‘0’), all PWM registers must be
reinitialized.
2008-2014 Microchip Technology Inc.
DS70000318G-page 149
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 9-2:
PMD2: PERIPHERAL MODULE DISABLE CONTROL REGISTER 2
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
IC2MD
IC1MD
bit 15
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
OC2MD
OC1MD
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-10
bit 9
Unimplemented: Read as ‘0’
IC2MD: Input Capture 2 Module Disable bit
1= Input Capture 2 module is disabled
0= Input Capture 2 module is enabled
bit 8
IC1MD: Input Capture 1 Module Disable bit
1= Input Capture 1 module is disabled
0= Input Capture 1 module is enabled
bit 7-2
bit 1
Unimplemented: Read as ‘0’
OC2MD: Output Compare 2 Module Disable bit
1= Output Compare 2 module is disabled
0= Output Compare 2 module is enabled
bit 0
OC1MD: Output Compare 1 Module Disable bit
1= Output Compare 1 module is disabled
0= Output Compare 1 module is enabled
DS70000318G-page 150
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 9-3:
PMD3: PERIPHERAL MODULE DISABLE CONTROL REGISTER 3
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
U-0
—
U-0
—
CMPMD
bit 15
bit 8
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-11
bit 10
Unimplemented: Read as ‘0’
CMPMD: Analog Comparator Module Disable bit
1= Analog comparator module is disabled
0= Analog comparator module is enabled
bit 9-0
Unimplemented: Read as ‘0’
REGISTER 9-4:
PMD4: PERIPHERAL MODULE DISABLE CONTROL REGISTER 4
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
U-0
—
U-0
—
U-0
—
REFOMD
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-4
bit 3
Unimplemented: Read as ‘0’
REFOMD: Reference Clock Generator Module Disable bit
1= Reference clock generator module is disabled
0= Reference clock generator module is enabled
bit 2-0
Unimplemented: Read as ‘0’
2008-2014 Microchip Technology Inc.
DS70000318G-page 151
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 9-5:
PMD6: PERIPHERAL MODULE DISABLE CONTROL REGISTER 6
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
PWM4MD
PWM3MD
PWM2MD
PWM1MD
bit 15
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-12
bit 11
Unimplemented: Read as ‘0’
PWM4MD: PWM Generator 4 Module Disable bit
1= PWM Generator 4 module is disabled
0= PWM Generator 4 module is enabled
bit 10
bit 9
bit 8
PWM3MD: PWM Generator 3 Module Disable bit
1= PWM Generator 3 module is disabled
0= PWM Generator 3 module is enabled
PWM2MD: PWM Generator 2 Module Disable bit
1= PWM Generator 2 module is disabled
0= PWM Generator 2 module is enabled
PWM1MD: PWM Generator 1 Module Disable bit
1= PWM Generator 1 module is disabled
0= PWM Generator 1 module is enabled
bit 7-0
Unimplemented: Read as ‘0’
DS70000318G-page 152
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 9-6:
PMD7: PERIPHERAL MODULE DISABLE CONTROL REGISTER 7
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
CMP4MD
CMP3MD
CMP2MD
CMP1MD
bit 15
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-12
bit 11
Unimplemented: Read as ‘0’
CMP4MD: Analog Comparator 4 Module Disable bit
1= Analog Comparator 4 module is disabled
0= Analog Comparator 4 module is enabled
bit 10
bit 9
bit 8
CMP3MD: Analog Comparator 3 Module Disable bit
1= Analog Comparator 3 module is disabled
0= Analog Comparator 3 module is enabled
CMP2MD: Analog Comparator 2 Module Disable bit
1= Analog Comparator 2 module is disabled
0= Analog Comparator 2 module is enabled
CMP1MD: Analog Comparator 1 Module Disable bit
1= Analog Comparator 1 module is disabled
0= Analog Comparator 1 module is enabled
bit 7-0
Unimplemented: Read as ‘0’
2008-2014 Microchip Technology Inc.
DS70000318G-page 153
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 154
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
has ownership of the output data and control signals of
the I/O pin. The logic also prevents “loop through”, in
10.0 I/O PORTS
which a port’s digital output can drive the input of a
peripheral that shares the same pin. Figure 10-1 shows
how ports are shared with other peripherals and the
associated I/O pin to which they are connected.
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a compre-
hensive reference source. To complement
the information in this data sheet, refer
to “I/O Ports” (DS70193) in the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available on Microchip
web site (www.microchip.com).
When a peripheral is enabled and the peripheral is
actively driving an associated pin, the use of the pin as a
general purpose output pin is disabled. The I/O pin can
be read, but the output driver for the parallel port bit is
disabled. If a peripheral is enabled, but the peripheral is
not actively driving a pin, that pin can be driven by a port.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
All port pins have three registers directly associated with
their operation as digital I/O. The data direction register
(TRISx) determines whether the pin is an input or an out-
put. If the data direction bit is ‘1’, then the pin is an input.
All port pins are defined as inputs after a Reset. Reads
from the latch (LATx) read the latch. Writes to the latch
write the latch. Reads from the port (PORTx) read the
port pins, while writes to the port pins write the latch.
All of the device pins (except VDD, VSS, MCLR and
OSC1/CLKI) are shared among the peripherals and the
parallel I/O ports. All I/O input ports feature Schmitt
Trigger inputs for improved noise immunity.
Any bit and its associated data and control registers
that are not valid for a particular device will be
disabled. That means the corresponding LATx and
TRISx registers and the port pin will read as zeros.
10.1 Parallel I/O (PIO) Ports
When a pin is shared with another peripheral or
function that is defined as an input only, it is
nevertheless regarded as a dedicated port because
there is no other competing source of outputs.
Generally a parallel I/O port that shares a pin with a
peripheral is subservient to the peripheral. The
peripheral’s output buffer data and control signals are
provided to a pair of multiplexers. The multiplexers
select whether the peripheral or the associated port
FIGURE 10-1:
BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE
Peripheral Module
Output Multiplexers
Peripheral Input Data
Peripheral Module Enable
I/O
Peripheral Output Enable
Peripheral Output Data
1
0
Output Enable
Output Data
1
0
PIO Module
Read TRIS
Data Bus
WR TRIS
D
Q
I/O Pin
CK
TRIS Latch
D
Q
WR LAT +
WR PORT
CK
Data Latch
Read LAT
Input Data
Read PORT
2008-2014 Microchip Technology Inc.
DS70000318G-page 155
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
10.2 Open-Drain Configuration
10.4 I/O Port Write/Read Timing
In addition to the PORTx, LATx and TRISx registers for
data control, some digital-only port pins can also be
individually configured for either digital or open-drain
output. This is controlled by the Open-Drain Control
register, ODCx, associated with each port. Setting any
of the bits configures the corresponding pin to act as an
open-drain output.
Oneinstructioncycleisrequiredbetweenaportdirection
change or port write operation and a read operation of
the same port. Typically, this instruction would be a NOP.
An example is shown in Example 10-1.
10.5 Input Change Notification
The Input Change Notification (ICN) function of the
I/O ports allows the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 devices to generate interrupt
The open-drain feature allows the generation of
outputs higher than VDD (for example, 5V) on any
desired 5V tolerant pins by using external pull-up
resistors. The maximum open-drain voltage allowed is
the same as the maximum VIH specification.
requests to the processor in response to
a
Change-of-State (COS) on selected input pins. This
feature can detect input Change-of-States even in
Sleep mode, when the clocks are disabled. Depending
on the device pin count, up to 30 external signals (CNx
pin) can be selected (enabled) for generating an
interrupt request on a Change-of-State.
Refer to “Pin Diagrams” for the available pins and
their functionality.
10.3 Configuring Analog Port Pins
Four control registers are associated with the CN
module. The CNEN1 and CNEN2 registers contain the
interrupt enable control bits for each of the CN input
pins. Setting any of these bits enables a CN interrupt
for the corresponding pins.
The ADPCFG and TRISx registers control the opera-
tion of the Analog-to-Digital (A/D) port pins. The port
pins that are to function as analog inputs must have
their corresponding TRISx bit set (input). If the TRISx
bit is cleared (output), the digital output level (VOH or
VOL) will be converted.
Each CN pin also has a weak pull-up connected to it.
The pull-ups act as a current source connected to the
pin, and eliminate the need for external resistors when
the push button or keypad devices are connected. The
pull-ups are enabled separately using the CNPU1 and
CNPU2 registers, which contain the control bits for
each of the CN pins. Setting any of the control bits
enables the weak pull-ups for the corresponding pins.
The ADPCFG register has a default value of 0x0000;
therefore, all pins that share ANx functions are analog
(not digital) by default.
When the PORTx register is read, all pins configured as
analog input channels will read as cleared (a low level).
Pins configured as digital inputs will not convert an
analog input. Analog levels on any pin defined as a
digital input (including the ANx pins) can cause the
input buffer to consume current that exceeds the
device specifications.
Note:
Pull-ups on Change Notification pins
should always be disabled when the port
pin is configured as a digital output.
EQUATION 10-1: PORT WRITE/READ EXAMPLE
MOV
MOV
NOP
0xFF00, W0
W0, TRISBB
; Configure PORTB<15:8> as inputs
; and PORTB<7:0> as outputs
; Delay 1 cycle
BTSS PORTB, #13
; Next Instruction
DS70000318G-page 156
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
10.6.2.1
Input Mapping
10.6 Peripheral Pin Select
The inputs of the Peripheral Pin Select options are
mapped on the basis of the peripheral. A control
register associated with a peripheral dictates the pin it
will be mapped to. The RPINRx registers are used to
configure peripheral input mapping (see Register 10-1
through Register 10-14). Each register contains sets of
6-bit fields, with each set associated with one of the
Peripheral Pin Select configuration enables peripheral
set selection and placement on a wide range of I/O
pins. By increasing the pinout options available on a
particular device, programmers can better tailor the
microcontroller to their entire application, rather than
trimming the application to fit the device.
The Peripheral Pin Select configuration feature operates
over a fixed subset of digital I/O pins. Programmers can
independently map the input and/or output of most
digital peripherals to any one of these I/O pins.
Peripheral Pin Select is performed in software, and gen-
erally does not require the device to be reprogrammed.
Hardware safeguards are included that prevent acciden-
tal or spurious changes to the peripheral mapping, once
it has been established.
remappable peripherals. Programming
a
given
peripheral’s bit field with an appropriate 6-bit value
maps the RPn pin with that value to that peripheral. For
any given device, the valid range of values for any bit
field corresponds to the maximum number of
Peripheral Pin Selections supported by the device.
Figure 10-2 Illustrates remappable pin selection for
U1RX input.
Note:
For input mapping only, the Peripheral Pin
Select (PPS) functionality does not have
priority over the TRISx settings. There-
fore, when configuring the RPx pin for
input, the corresponding bit in the TRISx
register must also be configured for input
(i.e., set to ‘1’).
10.6.1
AVAILABLE PINS
The Peripheral Pin Select feature is used with a range
of up to 30 pins. The number of available pins depends
on the particular device and its pin count. Pins that
support the Peripheral Pin Select feature include the
designation “RPn” in their full pin designation, where
“RP” designates a remappable peripheral and “n” is the
remappable pin number.
FIGURE 10-2:
REMAPPABLE MUX
INPUT FOR U1RX
10.6.2
CONTROLLING PERIPHERAL PIN
SELECT
U1RXR<5:0>
Peripheral Pin Select features are controlled through
two sets of Special Function Registers: one to map
peripheral inputs and another one to map outputs.
Because they are separately controlled, a particular
peripheral’s input and output (if the peripheral has both)
can be placed on any selectable function pin without
constraint.
0
RP0
RP1
RP2
1
U1RX Input
to Peripheral
2
The association of a peripheral to a peripheral select-
able pin is handled in two different ways, depending on
whether an input or output is being mapped.
33
RP33
2008-2014 Microchip Technology Inc.
DS70000318G-page 157
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 10-1: SELECTABLE INPUT SOURCES (MAPS INPUT TO FUNCTION)
Configuration
Input Name
Function Name
Register
Bits
External Interrupt 1
External Interrupt 2
Timer1 External Clock
Timer2 External Clock
Timer3 External Clock
Input Capture 1
INT1
INT2
RPINR0
RPINR1
INT1R<5:0>
INT2R<5:0>
T1CKR<5:0>
T2CKR<5:0>
T3CKR<5:0>
IC1R<5:0>
T1CK
T2CK
T3CK
IC1
RPINR2
RPINR3
RPINR3
RPINR7
Input Capture 2
IC2
RPINR7
IC2R<5:0>
Output Compare Fault A
OCFA
U1RX
U1CTS
SDI1
RPINR11
RPINR18
RPINR18
RPINR20
RPINR20
RPINR21
RPINR29
RPINR30
RPINR30
RPINR31
RPINR31
RPINR32
RPINR32
RPINR33
RPINR33
RPINR34
OCFAR<5:0>
U1RXR<5:0>
U1CTSR<5:0>
SDI1R<5:0>
SCK1R<5:0>
SS1R<5:0>
UART1 Receive
UART1 Clear-to-Send
SPI Data Input 1
SPI Clock Input 1
SCK1
SS1
SPI Slave Select Input 1
PWM Fault Input PWM1
FLT1
FLT2
FLT3
FLT4
FLT5
FLT6
FLT7
FLT8
SYNCI1
SYNCI2
FLT1R<5:0>
FLT2R<5:0>
FLT3R<5:0>
FLT4R<5:0>
FLT5R<5:0>
FLT6R<5:0>
FLT7R<5:0>
FLT8R<5:0>
SYNCI1R<5:0>
SYNCI2R<5:0>
PWM Fault Input PWM2
PWM Fault Input PWM3
PWM Fault Input PWM4
PWM Fault Input PWM5
PWM Fault Input PWM6
PWM Fault Input PWM7
PWM Fault Input PWM8
External Synchronization signal to PWM Master Time Base
External Synchronization signal to PWM Master Time Base
DS70000318G-page 158
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
10.6.2.2
Output Mapping
FIGURE 10-3:
MULTIPLEXING OF
REMAPPABLE OUTPUT
FOR RPn
In contrast to inputs, the outputs of the Peripheral Pin
Select options are mapped on the basis of the pin. In
this case, a control register associated with a particular
pin dictates the peripheral output to be mapped. The
RPORx registers are used to control output mapping.
Like the RPINRx registers, each register contains sets
of 6-bit fields, with each set associated with one RPn
pin (see Register 10-15 through Register 10-31). The
value of the bit field corresponds to one of the
peripherals, and that peripheral’s output is mapped to
the pin (see Table 10-2 and Figure 10-3).
RPORn<5:0>
Default
U1TX Output Enable
0
3
4
U1RTS Output Enable
Output Enable
The list of peripherals for output mapping also includes
a null value of ‘00000’ because of the mapping
technique. This permits any given pin to remain
unconnected from the output of any of the pin
selectable peripherals.
OC2 Output Enable
19
45
PWM4L Output Enable
Default
0
3
4
U1TX Output
U1RTS Output
RPn
Output Data
OC2 Output
19
45
PWM4L Output
TABLE 10-2: OUTPUT SELECTION FOR REMAPPABLE PIN (RPn)
Function
NULL
RPORn<5:0>
Output Name
000000
000011
000100
000111
001000
001001
010010
010011
100101
100110
100111
101000
101001
101010
101100
101101
RPn tied to default port pin
RPn tied to UART1 transmit
U1TX
U1RTS
SDO1
RPn tied to UART1 Ready-to-Send
RPn tied to SPI1 data output
SCK1
RPn tied to SPI1 clock output
RPn tied to SPI1 slave select output
RPn tied to Output Compare 1
RPn tied to Output Compare 2
SS1
OC1
OC2
SYNCO1
REFCLKO
ACMP1
ACMP2
ACMP3
ACMP4
PWM4H
PWM4L
RPn tied to external device synchronization signal via PWM master time base
REFCLK output signal
RPn tied to Analog Comparator Output 1
RPn tied to Analog Comparator Output 2
RPn tied to Analog Comparator Output 3
RPn tied to Analog Comparator Output 4
RPn tied to PWM output pins associated with PWM Generator 4
RPn tied to PWM output pins associated with PWM Generator 4
2008-2014 Microchip Technology Inc.
DS70000318G-page 159
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Unlike the similar sequence with the oscillator’s LOCK
bit, IOLOCK remains in one state until changed. This
allows all of the Peripheral Pin Selects to be configured
with a single unlock sequence followed by an update to
all control registers, then locked with a second lock
sequence.
10.6.2.3
Virtual Pins
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
devices support four virtual RPn pins (RP32, RP33,
RP34 and RP35), which are identical in functionality to
all other RPn pins, with the exception of pinouts. These
four pins are internal to the devices and are not
connected to a physical device pin.
10.6.3.2
Continuous State Monitoring
These pins provide a simple way for inter-peripheral
connection without utilizing a physical pin. For example,
the output of the analog comparator can be connected to
RP32 and the PWM Fault input can be configured for
RP32 as well. This configuration allows the analog
comparator to trigger PWM Faults without the use of an
actual physical pin on the device.
In addition to being protected from direct writes, the
contents of the RPINRx and RPORx registers are
constantly monitored in hardware by shadow registers.
If an unexpected change in any of the registers occurs
(such as cell disturbances caused by ESD or other
external events), a Configuration Mismatch Reset will
be triggered.
10.6.3
CONTROLLING CONFIGURATION
CHANGES
10.6.3.3
Configuration Bit Pin Select Lock
As an additional level of safety, the device can be
configured to prevent many write session to the
RPINRx and RPORx registers. The IOL1WAY
(FOSC<5>) Configuration bit blocks the IOLOCK bit
from being cleared after it has been set once. If
IOLOCK remains set, the register unlock procedure will
not execute and the Peripheral Pin Select Control
registers cannot be written to. The only way to clear the
bit and re-enable peripheral remapping is to perform a
device Reset.
Because peripheral remapping can be changed during
run time, some restrictions on peripheral remapping
are needed to prevent accidental configuration
changes. dsPIC33F devices include three features to
prevent alterations to the peripheral map:
• Control register lock sequence
• Continuous state monitoring
• Configuration bit pin select lock
10.6.3.1
Control Register Lock
In the default (unprogrammed) state, IOL1WAY is set,
restricting users to one write session. Programming
IOL1WAY allows user applications unlimited access
(with the proper use of the unlock sequence) to the
Peripheral Pin Select registers.
Under normal operation, writes to the RPINRx and
RPORx registers are not allowed. Attempted writes
appear to execute normally, but the contents of the
registers remain unchanged. To change these
registers, they must be unlocked in hardware. The
register lock is controlled by the IOLOCK bit
(OSCCON<6>). Setting IOLOCK prevents writes to the
control registers; clearing IOLOCK allows writes.
To set or clear IOLOCK, a specific command sequence
must be executed:
1. Write 0x46 to OSCCON<7:0>.
2. Write 0x57 to OSCCON<7:0>.
3. Clear (or set) IOLOCK as a single operation.
Note:
MPLAB® C30 provides built-in
C
language functions for unlocking the
OSCCON register:
__builtin_write_OSCCONL(value)
__builtin_write_OSCCONH(value)
See the MPLAB C30 Help files for more
information.
DS70000318G-page 160
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Not all output remappable peripheral registers are
10.7 Peripheral Pin Select Registers
implemented on all devices. See the specific register
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
description for further details.
families of devices implement 34 registers for
remappable peripheral configuration:
• 15 Input Remappable Peripheral Registers
• 17 Output Remappable Peripheral Registers
Note:
Input and output register values can only
be changed if OSCCON<IOLOCK> = 0.
See Section 10.6.3.1 “Control Register
Lock” for a specific command sequence.
REGISTER 10-1: RPINR0: PERIPHERAL PIN SELECT INPUT REGISTER 0
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
INT1R5
INT1R4
INT1R3
INT1R2
INT1R1
INT1R0
bit 15
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
INT1R<5:0>: Assign External Interrupt 1 (INTR1) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
bit 7-0
Unimplemented: Read as ‘0’
2008-2014 Microchip Technology Inc.
DS70000318G-page 161
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-2: RPINR1: PERIPHERAL PIN SELECT INPUT REGISTER 1
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
INT2R5
INT2R4
INT2R3
INT2R2
INT2R1
INT2R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-6
bit 5-0
Unimplemented: Read as ‘0’
INT2R<5:0>: Assign External Interrupt 2 (INTR2) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
DS70000318G-page 162
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-3: RPINR3: PERIPHERAL PIN SELECT INPUT REGISTER 3
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
T3CKR5
T3CKR4
T3CKR3
T3CKR2
T3CKR1
T3CKR0
bit 15
bit 8
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
T2CKR5
T2CKR4
T2CKR3
T2CKR2
T2CKR1
T2CKR0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
T3CKR<5:0>: Assign Timer3 External Clock (T3CK) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
T2CKR<5:0>: Assign Timer2 External Clock (T2CK) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
2008-2014 Microchip Technology Inc.
DS70000318G-page 163
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-4: RPINR7: PERIPHERAL PIN SELECT INPUT REGISTER 7
U-0
—
U-0
—
R/W-1
IC2R5
R/W-1
IC2R4
R/W-1
IC2R3
R/W-1
IC2R2
R/W-1
IC2R1
R/W-1
IC2R0
bit 15
bit 8
U-0
—
U-0
—
R/W-1
IC1R5
R/W-1
IC1R4
R/W-1
IC1R3
R/W-1
IC1R2
R/W-1
IC1R1
R/W-1
IC1R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
IC2R<5:0>: Assign Input Capture 2 (IC2) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
IC1R<5:0>: Assign Input Capture 1 (IC1) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
DS70000318G-page 164
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-5: RPINR11: PERIPHERAL PIN SELECT INPUT REGISTER 11
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
OCFAR5
OCFAR4
OCFAR3
OCFAR2
OCFAR1
OCFAR0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-6
bit 5-0
Unimplemented: Read as ‘0’
OCFAR<5:0>: Assign Output Capture A (OCFA) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
2008-2014 Microchip Technology Inc.
DS70000318G-page 165
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-6: RPINR18: PERIPHERAL PIN SELECT INPUT REGISTER 18
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
U1CTSR5
U1CTSR4
U1CTSR3
U1CTSR2
U1CTSR1
U1CTSR0
bit 15
bit 8
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
U1RXR5
U1RXR4
U1RXR3
U1RXR2
U1RXR1
U1RXR0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
U1CTSR<5:0>: Assign UART1 Clear-to-Send (U1CTS) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
U1RXR<5:0>: Assign UART1 Receive (U1RX) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
DS70000318G-page 166
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-7: RPINR20: PERIPHERAL PIN SELECT INPUT REGISTER 20
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
SCK1R5
SCK1R4
SCK1R3
SCK1R2
SCK1R1
SCK1R0
bit 15
bit 8
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
SDI1R5
SDI1R4
SDI1R3
SDI1R2
SDI1R1
SDI1R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
SCK1R<5:0>: Assign SPI1 Clock Input (SCK1IN) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
SDI1R<5:0>: Assign SPI1 Data Input (SDI1) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
2008-2014 Microchip Technology Inc.
DS70000318G-page 167
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-8: RPINR21: PERIPHERAL PIN SELECT INPUT REGISTER 21
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
SS1R5
SS1R4
SS1R3
SS1R2
SS1R1
SS1R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-6
bit 5-0
Unimplemented: Read as ‘0’
SS1R<5:0>: Assign SPI1 Slave Select Input (SS1IN) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
DS70000318G-page 168
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-9: RPINR29: PERIPHERAL PIN SELECT INPUT REGISTER 29
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
FLT1R5
FLT1R4
FLT1R3
FLT1R2
FLT1R1
FLT1R0
bit 15
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
FLT1R<5:0>: Assign PWM Fault Input 1 (FLT1) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
bit 7-0
Unimplemented: Read as ‘0’
2008-2014 Microchip Technology Inc.
DS70000318G-page 169
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-10: RPINR30: PERIPHERAL PIN SELECT INPUT REGISTER 30
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
FLT3R5
FLT3R4
FLT3R3
FLT3R2
FLT3R1
FLT3R0
bit 15
bit 8
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
FLT2R5
FLT2R4
FLT2R3
FLT2R2
FLT2R1
FLT2R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
FLT3R<5:0>: Assign PWM Fault Input 3 (FLT3) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
FLT2R<5:0>: Assign PWM Fault Input 2 (FLT2) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
DS70000318G-page 170
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-11: RPINR31: PERIPHERAL PIN SELECT INPUT REGISTER 31
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
FLT5R5
FLT5R4
FLT5R3
FLT5R2
FLT5R1
FLT5R0
bit 15
bit 8
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
FLT4R5
FLT4R4
FLT4R3
FLT4R2
FLT4R1
FLT4R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
FLT5R<5:0>: Assign PWM Fault Input 5 (FLT5) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
FLT4R<5:0>: Assign PWM Fault Input 4 (FLT4) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
2008-2014 Microchip Technology Inc.
DS70000318G-page 171
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-12: RPINR32: PERIPHERAL PIN SELECT INPUT REGISTER 32
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
FLT7R5
FLT7R4
FLT7R3
FLT7R2
FLT7R1
FLT7R0
bit 15
bit 8
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
FLT6R5
FLT6R4
FLT6R3
FLT6R2
FLT6R1
FLT6R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
FLT7R<5:0>: Assign PWM Fault Input 7 (FLT7) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
FLT6R<5:0>: Assign PWM Fault Input 6 (FLT6) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
DS70000318G-page 172
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-13: RPINR33: PERIPHERAL PIN SELECT INPUT REGISTER 33
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
SYNCI1R0
bit 8
SYNCI1R5 SYNCI1R4 SYNCI1R3
SYNCI1R2
SYNCI1R1
bit 15
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
FLT8R0
bit 0
FLT8R5
FLT8R4
FLT8R3
FLT8R2
FLT8R1
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
SYNCI1R<5:0>: Assign PWM Master Time Base External Synchronization Signal to the
Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
FLT8R<5:0>: Assign PWM Fault Input 8 (FLT8) to the Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
2008-2014 Microchip Technology Inc.
DS70000318G-page 173
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-14: RPINR34: PERIPHERAL PIN SELECT INPUT REGISTER 34
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
SYNCI2R0
bit 0
SYNCI2R5 SYNCI2R4 SYNCI2R3
SYNCI2R2
SYNCI2R1
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-6
bit 5-0
Unimplemented: Read as ‘0’
SYNCI2R<5:0>: Assign PWM Master Time Base External Synchronization Signal to the
Corresponding RPn Pin bits
111111= Input tied to VSS
100011= Input tied to RP35
100010= Input tied to RP34
100001= Input tied to RP33
100000= Input tied to RP32
•
•
•
00000= Input tied to RP0
REGISTER 10-15: RPOR0: PERIPHERAL PIN SELECT OUTPUT REGISTER 0
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP1R0
bit 8
RP1R5
RP1R4
RP1R3
RP1R2
RP1R1
bit 15
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP0R0
bit 0
RP0R5
RP0R4
RP0R3
RP0R2
RP0R1
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP1R<5:0>: Peripheral Output Function is Assigned to RP1 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP0R<5:0>: Peripheral Output Function is Assigned to RP0 Output Pin bits
(see Table 10-2 for peripheral function numbers)
DS70000318G-page 174
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-16: RPOR1: PERIPHERAL PIN SELECT OUTPUT REGISTER 1
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP3R5
RP3R4
RP3R3
RP3R2
RP3R1
RP3R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP2R5
RP2R4
RP2R3
RP2R2
RP2R1
RP2R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP3R<5:0>: Peripheral Output Function is Assigned to RP3 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP2R<5:0>: Peripheral Output Function is Assigned to RP2 Output Pin bits
(see Table 10-2 for peripheral function numbers)
REGISTER 10-17: RPOR2: PERIPHERAL PIN SELECT OUTPUT REGISTER 2
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP5R5
RP5R4
RP5R3
RP5R2
RP5R1
RP5R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP4R5
RP4R4
RP4R3
RP4R2
RP4R1
RP4R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP5R<5:0>: Peripheral Output Function is Assigned to RP5 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP4R<5:0>: Peripheral Output Function is Assigned to RP4 Output Pin bits
(see Table 10-2 for peripheral function numbers)
2008-2014 Microchip Technology Inc.
DS70000318G-page 175
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-18: RPOR3: PERIPHERAL PIN SELECT OUTPUT REGISTER 3
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP7R5
RP7R4
RP7R3
RP7R2
RP7R1
RP7R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP6R5
RP6R4
RP6R3
RP6R2
RP6R1
RP6R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP7R<5:0>: Peripheral Output Function is Assigned to RP7 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP6R<5:0>: Peripheral Output Function is Assigned to RP6 Output Pin bits
(see Table 10-2 for peripheral function numbers)
REGISTER 10-19: RPOR4: PERIPHERAL PIN SELECT OUTPUT REGISTER 4(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP9R5
RP9R4
RP9R3
RP9R2
RP9R1
RP9R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP8R5
RP8R4
RP8R3
RP8R2
RP8R1
RP8R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP9R<5:0>: Peripheral Output Function is Assigned to RP9 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP8R<5:0>: Peripheral Output Function is Assigned to RP8 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is not implemented in the dsPIC33FJ06GS101 device.
DS70000318G-page 176
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-20: RPOR5: PERIPHERAL PIN SELECT OUTPUT REGISTER 5(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP11R5
RP11R4
RP11R3
RP11R2
RP11R1
RP11R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP10R5
RP10R4
RP10R3
RP10R2
RP10R1
RP10R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP11R<5:0>: Peripheral Output Function is Assigned to RP11 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP10R<5:0>: Peripheral Output Function is Assigned to RP10 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is not implemented in the dsPIC33FJ06GS101 device.
REGISTER 10-21: RPOR6: PERIPHERAL PIN SELECT OUTPUT REGISTER 6(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP13R5
RP13R4
RP13R3
RP13R2
RP13R1
RP13R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP12R5
RP12R4
RP12R3
RP12R2
RP12R1
RP12R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP13R<5:0>: Peripheral Output Function is Assigned to RP13 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP12R<5:0>: Peripheral Output Function is Assigned to RP12 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is not implemented in the dsPIC33FJ06GS101 device.
2008-2014 Microchip Technology Inc.
DS70000318G-page 177
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-22: RPOR7: PERIPHERAL PIN SELECT OUTPUT REGISTER 7(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP15R5
RP15R4
RP15R3
RP15R2
RP15R1
RP15R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP14R5
RP14R4
RP14R3
RP14R2
RP14R1
RP14R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP15R<5:0>: Peripheral Output Function is Assigned to RP15 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP14R<5:0>: Peripheral Output Function is Assigned to RP14 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is not implemented in the dsPIC33FJ06GS101 device.
REGISTER 10-23: RPOR8: PERIPHERAL PIN SELECT OUTPUT REGISTER 8(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP17R5
RP17R4
RP17R3
RP17R2
RP17R1
RP17R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP16R5
RP16R4
RP16R3
RP16R2
RP16R1
RP16R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP17R<5:0>: Peripheral Output Function is Assigned to RP17 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP16R<5:0>: Peripheral Output Function is Assigned to RP16 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is implemented in the dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only.
DS70000318G-page 178
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-24: RPOR9: PERIPHERAL PIN SELECT OUTPUT REGISTER 9(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP19R5
RP19R4
RP19R3
RP19R2
RP19R1
RP19R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP18R5
RP18R4
RP18R3
RP18R2
RP18R1
RP18R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP19R<5:0>: Peripheral Output Function is Assigned to RP19 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP18R<5:0>: Peripheral Output Function is Assigned to RP18 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is implemented in the dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only.
REGISTER 10-25: RPOR10: PERIPHERAL PIN SELECT OUTPUT REGISTER 10(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP21R5
RP21R4
RP21R3
RP21R2
RP21R1
RP21R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP20R5
RP20R4
RP20R3
RP20R2
RP20R1
RP20R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP21R<5:0>: Peripheral Output Function is Assigned to RP21 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP20R<5:0>: Peripheral Output Function is Assigned to RP20 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is implemented in the dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only.
2008-2014 Microchip Technology Inc.
DS70000318G-page 179
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-26: RPOR11: PERIPHERAL PIN SELECT OUTPUT REGISTER 11(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP23R5
RP23R4
RP23R3
RP23R2
RP23R1
RP23R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP22R5
RP22R4
RP22R3
RP22R2
RP22R1
RP22R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP23R<5:0>: Peripheral Output Function is Assigned to RP23 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP22R<5:0>: Peripheral Output Function is Assigned to RP22 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is implemented in the dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only.
REGISTER 10-27: RPOR12: PERIPHERAL PIN SELECT OUTPUT REGISTER 12(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP25R5
RP25R4
RP25R3
RP25R2
RP25R1
RP25R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP24R5
RP24R4
RP24R3
RP24R2
RP24R1
RP24R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP25R<5:0>: Peripheral Output Function is Assigned to RP25 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP24R<5:0>: Peripheral Output Function is Assigned to RP24 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is implemented in the dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only.
DS70000318G-page 180
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-28: RPOR13: PERIPHERAL PIN SELECT OUTPUT REGISTER 13(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP27R5
RP27R4
RP27R3
RP27R2
RP27R1
RP27R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP26R5
RP26R4
RP26R3
RP26R2
RP26R1
RP26R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP27R<5:0>: Peripheral Output Function is Assigned to RP27 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP26R<5:0>: Peripheral Output Function is Assigned to RP26 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is implemented in the dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only.
REGISTER 10-29: RPOR14: PERIPHERAL PIN SELECT OUTPUT REGISTER 14(1)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP29R5
RP29R4
RP29R3
RP29R2
RP29R1
RP29R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP28R5
RP28R4
RP28R3
RP28R2
RP28R1
RP28R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP29R<5:0>: Peripheral Output Function is Assigned to RP29 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP28R<5:0>: Peripheral Output Function is Assigned to RP28 Output Pin bits
(see Table 10-2 for peripheral function numbers)
Note 1: This register is implemented in the dsPIC33FJ16GS404 and dsPIC33FJ16GS504 devices only.
2008-2014 Microchip Technology Inc.
DS70000318G-page 181
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 10-30: RPOR16: PERIPHERAL PIN SELECT OUTPUT REGISTER 16
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP33R5
RP33R4
RP33R3
RP33R2
RP33R1
RP33R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP32R5
RP32R4
RP32R3
RP32R2
RP32R1
RP32R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP33R<5:0>: Peripheral Output Function is Assigned to RP33 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP32R<5:0>: Peripheral Output Function is Assigned to RP32 Output Pin bits
(see Table 10-2 for peripheral function numbers)
REGISTER 10-31: RPOR17: PERIPHERAL PIN SELECT OUTPUT REGISTER 17
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP35R5
RP35R4
RP35R3
RP35R2
RP35R1
RP35R0
bit 15
bit 8
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
RP34R5
RP34R4
RP34R3
RP34R2
RP34R1
RP34R0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-8
Unimplemented: Read as ‘0’
RP35R<5:0>: Peripheral Output Function is Assigned to RP35 Output Pin bits
(see Table 10-2 for peripheral function numbers)
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RP34R<5:0>: Peripheral Output Function is Assigned to RP34 Output Pin bits
(see Table 10-2 for peripheral function numbers)
DS70000318G-page 182
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The unique features of Timer1 allow it to be used for
Real-Time Clock (RTC) applications. A block diagram
11.0 TIMER1
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “Timers” (DS70205) in
the “dsPIC33F/PIC24H Family Reference
Manual”, which is available from the
Microchip web site (www.microchip.com).
of Timer1 is shown in Figure 11-1.
The Timer1 module can operate in one of the following
modes:
• Timer mode
• Gated Timer mode
• Synchronous Counter mode
• Asynchronous Counter mode
In Timer and Gated Timer modes, the input clock is
derived from the internal instruction cycle clock (FCY).
In Synchronous and Asynchronous Counter modes,
the input clock is derived from the external clock input
at the T1CK pin.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The Timer modes are determined by the following bits:
• Timer Clock Source Control bit (TCS): T1CON<1>
• Timer Synchronization Control bit (TSYNC):
T1CON<2>
The Timer1 module is a 16-bit timer, which can serve
as a time counter for the Real-Time Clock (RTC), or
operate as a free-running interval timer/counter.
• Timer Gate Control bit (TGATE): T1CON<6>
The timer control bit settings for different operating
modes are given in the Table 11-1.
The Timer1 module has the following unique features
over other timers:
TABLE 11-1: TIMER MODE SETTINGS
• Can be operated from the low-power 32 kHz
crystal oscillator available on the device
Mode
Timer
TCS
TGATE
TSYNC
• Can be operated in Asynchronous Counter mode
from an external clock source
0
0
1
0
1
x
x
x
1
Gated Timer
• Optionally, the external clock input (T1CK) can be
synchronized to the internal device clock and the
clock synchronization is performed after the
prescaler
Synchronous
Counter
Asynchronous
Counter
1
x
0
FIGURE 11-1:
16-BIT TIMER1 MODULE BLOCK DIAGRAM
Falling Edge
Gate
Sync
1
0
Detect
Set T1IF Flag
FCY
10
Prescaler
(/n)
TGATE
Reset
Equal
TMR1
00
x1
TCKPS<1:0>
0
1
T1CK
Prescaler
(/n)
Comparator
PR1
Sync
TGATE
TCS
TSYNC
TCKPS<1:0>
2008-2014 Microchip Technology Inc.
DS70000318G-page 183
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 11-1: T1CON: TIMER1 CONTROL REGISTER
R/W-0
TON
U-0
—
R/W-0
TSIDL
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
bit 0
U-0
—
R/W-0
R/W-0
R/W-0
U-0
—
R/W-0
R/W-0
TCS
U-0
—
TGATE
TCKPS1
TCKPS0
TSYNC
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
TON: Timer1 On bit
1= Starts 16-bit Timer1
0= Stops 16-bit Timer1
bit 14
bit 13
Unimplemented: Read as ‘0’
TSIDL: Timer1 Stop in Idle Mode bit
1= Discontinues module operation when device enters Idle mode
0= Continues module operation in Idle mode
bit 12-7
bit 6
Unimplemented: Read as ‘0’
TGATE: Timer1 Gated Time Accumulation Enable bit
When TCS = 1:
This bit is ignored.
When TCS = 0:
1= Gated time accumulation is enabled
0= Gated time accumulation is disabled
bit 5-4
TCKPS<1:0> Timer1 Input Clock Prescale Select bits
11 = 1:256
10 = 1:64
01 = 1:8
00 = 1:1
bit 3
bit 2
Unimplemented: Read as ‘0’
TSYNC: Timer1 External Clock Input Synchronization Select bit
When TCS = 1:
1= Synchronizes external clock input
0= Does not synchronize external clock input
When TCS = 0:
This bit is ignored.
bit 1
bit 0
TCS: Timer1 Clock Source Select bit
1= External clock from T1CK pin (on the rising edge)
0= Internal clock (FCY)
Unimplemented: Read as ‘0’
DS70000318G-page 184
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Timer2 is a Type B timer that offers the following major
features:
12.0 TIMER2/3 FEATURES
Note 1: This data sheet summarizes the features
• A Type B timer can be concatenated with a
of the dsPIC33FJ06GS101/X02 and
Type C timer to form a 32-bit timer
dsPIC33FJ16GSX02/X04 families of
• Externalclockinput(TxCK)isalwayssynchronized
devices. It is not intended to be a
to the internal device clock and the clock
comprehensive reference source. To
synchronization is performed after the prescaler.
complement the information in this data
Figure 12-1 shows a block diagram of the Type B timer.
sheet, refer to “Timers” (DS70205) in
the “dsPIC33F/PIC24H Family Reference
Manual”, which is available on the
Microchip web site (www.microchip.com).
Timer3 is a Type C timer that offers the following major
features:
• A Type C timer can be concatenated with a
Type B timer to form a 32-bit timer
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
• The external clock input (TxCK) is always
synchronized to the internal device clock and the clock
synchronization is performed before the prescaler
A block diagram of the Type C timer is shown in
Figure 12-2.
Note:
Timer3 is not available on all devices.
FIGURE 12-1:
TYPE B TIMER BLOCK DIAGRAM (x = 2)
Falling Edge
Detect
Gate
Sync
1
Set TxIF Flag
FCY
10
00
0
Prescaler
(/n)
Reset
TMRx
TCKPS<1:0>
Sync
TGATE
Prescaler
(/n)
x1
Equal
Comparator
TxCK
TCKPS<1:0>
TGATE
TCS
PRx
FIGURE 12-2:
TYPE C TIMER BLOCK DIAGRAM (x = 3)
Falling Edge
Detect
Gate
Sync
1
Set TxIF Flag
Prescaler
(/n)
0
10
00
x1
FCY
Reset
TMRx
TGATE
TCKPS<1:0>
Prescaler
(/n)
Sync
Equal
Comparator
TxCK
TCKPS<1:0>
TGATE
TCS
PRx
2008-2014 Microchip Technology Inc.
DS70000318G-page 185
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The Timer2/3 module can operate in one of the
following modes:
When configured for 32-bit operation, only the Type B
Timer Control (TxCON) register bits are required for
setup and control while the Type C Timer Control
register bits are ignored (except the TSIDL bit).
• Timer mode
• Gated Timer mode
• Synchronous Counter mode
For interrupt control, the combined 32-bit timer uses
the interrupt enable, interrupt flag and interrupt priority
control bits of the Type C timer. The interrupt control
and status bits for the Type B timer are ignored
during 32-bit timer operation.
In Timer and Gated Timer modes, the input clock is
derived from the internal instruction cycle clock (FCY).
In Synchronous Counter mode, the input clock is
derived from the external clock input at the TxCK pin.
The Timer2 and Timer 3 that can be combined to form a
32-bit timer are listed in Table 12-2.
The timer modes are determined by the following bits:
• TCS (TxCON<1>): Timer Clock Source Control bit
• TGATE (TxCON<6>): Timer Gate Control bit
TABLE 12-2: 32-BIT TIMER
Timer control bit settings for different operating modes
are given in the Table 12-1.
Type B Timer (lsw)
Type C Timer (msw)
Timer2
Timer3
TABLE 12-1: TIMER MODE SETTINGS
A block diagram representation of the 32-bit timer
module is shown in Figure 12-3. The 32-timer module
can operate in one of the following modes:
Mode
TCS
TGATE
Timer
0
0
1
0
1
x
• Timer mode
• Gated Timer mode
• Synchronous Counter mode
Gated Timer
Synchronous Counter
To configure the features of Timer2/3 for 32-bit
operation:
12.1 16-Bit Operation
1. Set the T32 control bit.
To configure any of the timers for individual 16-bit
operation:
2. Select the prescaler ratio for Timer2 using the
TCKPS<1:0> bits.
1. Clear the T32 bit corresponding to that timer.
3. Set the Clock and Gating modes using the
corresponding TCS and TGATE bits.
2. Select the timer prescaler ratio using the
TCKPS<1:0> bits.
4. Load the timer period value. PR3 contains the
most significant word of the value, while PR2
contains the least significant word.
3. Set the Clock and Gating modes using the TCS
and TGATE bits.
4. Load the timer period value into the PRx
register.
5. If interrupts are required, set the interrupt enable
bit, T3IE. Use the priority bits, T3IP<2:0>, to set
the interrupt priority. While Timer2 controls the
timer, the interrupt appears as a Timer3
interrupt.
5. If interrupts are required, set the interrupt enable
bit, TxIE. Use the priority bits, TxIP<2:0>, to set
the interrupt priority.
6. Set the TON bit.
6. Set the corresponding TON bit.
The timer value at any point is stored in the register
pair, TMR3:TMR2, which always contains the most
significant word of the count, while TMR2 contains the
least significant word.
12.2 32-Bit Operation
A 32-bit timer module can be formed by combining a
Type B and a Type C 16-bit timer module. For 32-bit
timer operation, the T32 control bit in the Type B Timer
Control (TxCON<3>) register must be set. The Type C
timer holds the most significant word (msw) and the
Type B timer holds the least significant word (lsw)
for 32-bit operation.
DS70000318G-page 186
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 12-3:
32-BIT TIMER BLOCK DIAGRAM
Falling Edge
Detect
Gate
Sync
1
0
Set TyIF
Flag
PRy
PRx
Equal
Reset
Comparator
TGATE
Prescaler
(/n)
10
00
x1
FCY
lsw
msw
TMRx(1)
TMRy(2)
TCKPS<1:0>
Sync
Prescaler
(/n)
TxCK
TMRyHLD
TCKPS<1:0>
TGATE
TCS
Data Bus <15:0>
Note 1: Timerx is a Type B Timer (x = 2).
2: Timery is a Type C Timer (y = 3).
2008-2014 Microchip Technology Inc.
DS70000318G-page 187
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 12-1: TxCON: TIMERx CONTROL REGISTER (x = 2)
R/W-0
TON
U-0
—
R/W-0
TSIDL
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
bit 0
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
T32
U-0
—
R/W-0
TCS
U-0
—
TGATE
TCKPS1
TCKPS0
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
TON: Timerx On bit
When T32 = 1(in 32-Bit Timer mode):
1= Starts 32-bit TMRx:TMRy timer pair
0= Stops 32-bit TMRx:TMRy timer pair
When T32 = 0(in 16-Bit Timer mode):
1= Starts 16-bit timer
0= Stops 16-bit timer
bit 14
bit 13
Unimplemented: Read as ‘0’
TSIDL: Timerx Stop in Idle Mode bit
1= Discontinues timer operation when device enters Idle mode
0= Continues timer operation in Idle mode
bit 12-7
bit 6
Unimplemented: Read as ‘0’
TGATE: Timerx Gated Time Accumulation Enable bit
When TCS = 1:
This bit is ignored.
When TCS = 0:
1= Gated time accumulation is enabled
0= Gated time accumulation is disabled
bit 5-4
bit 3
TCKPS<1:0>: Timerx Input Clock Prescale Select bits
11= 1:256 prescale value
10= 1:64 prescale value
01= 1:8 prescale value
00= 1:1 prescale value
T32: 32-Bit Timerx Mode Select bit
1= TMRx and TMRy form a 32-bit timer
0= TMRx and TMRy form a separate 16-bit timer
bit 2
bit 1
Unimplemented: Read as ‘0’
TCS: Timerx Clock Source Select bit
1= External clock from TxCK pin
0= Internal clock (FOSC/2)
bit 0
Unimplemented: Read as ‘0’
DS70000318G-page 188
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 12-2: TyCON: TIMERy CONTROL REGISTER (y = 3)
R/W-0
TON(2)
U-0
—
R/W-0
TSIDL(1)
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
bit 0
U-0
—
R/W-0
TGATE(2)
R/W-0
TCKPS1(2) TCKPS0(2)
R/W-0
U-0
—
U-0
—
R/W-0
TCS(2)
U-0
—
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
TON: Timery On bit(2)
1= Starts 16-bit Timery
0= Stops 16-bit Timery
bit 14
bit 13
Unimplemented: Read as ‘0’
TSIDL: Timery Stop in Idle Mode bit(1)
1= Discontinues timer operation when device enters Idle mode
0= Continues timer operation in Idle mode
bit 12-7
bit 6
Unimplemented: Read as ‘0’
TGATE: Timery Gated Time Accumulation Enable bit(2)
When TCS = 1:
This bit is ignored.
When TCS = 0:
1= Gated time accumulation is enabled
0= Gated time accumulation is disabled
bit 5-4
TCKPS<1:0>: Timery Input Clock Prescale Select bits(2)
11= 1:256 prescale value
10= 1:64 prescale value
01= 1:8 prescale value
00= 1:1 prescale value
bit 3-2
bit 1
Unimplemented: Read as ‘0’
TCS: Timery Clock Source Select bit(2)
1= External clock from TxCK pin
0= Internal clock (FOSC/2)
bit 0
Unimplemented: Read as ‘0’
Note 1: When 32-bit timer operation is enabled (T32 = 1) in the Timerx Control register (TxCON<3>), the TSIDL
bit must be cleared to operate the 32-bit timer in Idle mode.
2: When the 32-bit timer operation is enabled (T32 = 1) in the Timerx Control (TxCON<3>) register, these
bits have no effect.
2008-2014 Microchip Technology Inc.
DS70000318G-page 189
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 190
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The input capture module captures the 16-bit value of
the selected Time Base register when an event occurs
13.0 INPUT CAPTURE
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “Input Capture”
(DS70198) in the “dsPIC33F/PIC24H
Family Reference Manual”, which is
available on the Microchip web site
(www.microchip.com).
at the ICx pin. The events that cause a capture event
are listed below in three categories:
• Simple Capture Event modes:
- Capture timer value on every falling edge of
input at ICx pin
- Capture timer value on every rising edge of
input at ICx pin
• Capture timer value on every edge (rising and
falling)
• Prescaler Capture Event modes:
- Capture timer value on every 4th rising edge
of input at ICx pin
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
- Capture timer value on every 16th rising
edge of input at ICx pin
Each input capture channel can select one of the
two 16-bit timers (Timer2 or Timer3) for the time
base. The selected timer can use either an internal
or external clock.
The input capture module is useful in applications
requiring frequency (period) and pulse measurement.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
devices support up to two input capture channels.
Other operational features include:
• Device wake-up from capture pin during CPU
Sleep and Idle modes
• Interrupt on input capture event
• 4-word FIFO buffer for capture values
- Interrupt optionally generated after 1, 2, 3 or
4 buffer locations are filled
• Use of input capture to provide additional sources
of external interrupts
FIGURE 13-1:
INPUT CAPTURE x BLOCK DIAGRAM
From 16-Bit Timers
TMR2 TMR3
16
16
ICTMR
(ICxCON<7>)
1
0
Edge Detection Logic
and
Clock Synchronizer
FIFO
R/W
Logic
Prescaler
Counter
(1, 4, 16)
ICx Pin
ICM<2:0> (ICxCON<2:0>)
3
Mode Select
ICOV, ICBNE (ICxCON<4:3>)
ICxBUF
ICxI<1:0>
Interrupt
Logic
ICxCON
System Bus
Set Flag ICxIF
(in IFSx Register)
Note 1: An ‘x’ in a signal, register or bit name denotes the number of the capture channel.
2008-2014 Microchip Technology Inc.
DS70000318G-page 191
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
13.1 Input Capture Register
REGISTER 13-1: ICxCON: INPUT CAPTURE x CONTROL REGISTER (x = 1, 2)
U-0
—
U-0
—
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
ICSIDL
bit 15
bit 8
R/W-0
R/W-0
ICI1
R/W-0
ICI0
R-0, HC
ICOV
R-0, HC
ICBNE
R/W-0
ICM2
R/W-0
ICM1
R/W-0
ICM0
ICTMR
bit 7
bit 0
Legend:
HC = Hardware Clearable bit
W = Writable bit
R = Readable bit
-n = Value at POR
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
‘1’ = Bit is set
bit 15-14
bit 13
Unimplemented: Read as ‘0’
ICSIDL: Input Capture Module Stop in Idle Control bit
1= Input capture module halts in CPU Idle mode
0= Input capture module continues to operate in CPU Idle mode
bit 12-8
bit 7
Unimplemented: Read as ‘0’
ICTMR: Input Capture Timer Select bits
1= TMR2 contents are captured on a capture event
0= TMR3 contents are captured on a capture event
bit 6-5
ICI<1:0>: Select Number of Captures per Interrupt bits
11= Interrupt on every fourth capture event
10= Interrupt on every third capture event
01= Interrupt on every second capture event
00= Interrupt on every capture event
bit 4
ICOV: Input Capture Overflow Status Flag bit (read-only)
1= Input capture overflow occurred
0= No input capture overflow occurred
bit 3
ICBNE: Input Capture Buffer Empty Status bit (read-only)
1= Input capture buffer is not empty, at least one more capture value can be read
0= Input capture buffer is empty
bit 2-0
ICM<2:0>: Input Capture Mode Select bits
111= Input capture functions as interrupt pin only when device is in Sleep or Idle mode; rising edge
detect only, all other control bits are not applicable
110= Unused (module disabled)
101= Capture mode, every 16th rising edge
100= Capture mode, every 4th rising edge
011= Capture mode, every rising edge
010= Capture mode, every falling edge
001= Capture mode, every edge (rising and falling); ICI<1:0> bits do not control interrupt generation
for this mode
000= Input capture module turned off
DS70000318G-page 192
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The output compare module can select either Timer2 or
Timer3 for its time base. The module compares the
14.0 OUTPUT COMPARE
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “Output Compare”
(DS70005157) in the “dsPIC33F/PIC24H
Family Reference Manual”, which is
available on the Microchip web site
(www.microchip.com).
value of the timer with the value of one or two Compare
registers depending on the operating mode selected.
The state of the output pin changes when the timer
value matches the Compare register value. The output
compare module generates either a single output
pulse, or a sequence of output pulses, by changing the
state of the output pin on the compare match events.
The output compare module can also generate
interrupts on compare match events.
The output compare module has multiple operating
modes:
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
• Active-Low One-Shot mode
• Active-High One-Shot mode
• Toggle mode
• Delayed One-Shot mode
• Continuous Pulse mode
• PWM mode without Fault Protection
• PWM mode with Fault Protection
FIGURE 14-1:
OUTPUT COMPARE x MODULE BLOCK DIAGRAM
Set Flag bit
OCxIF
OCxRS
OCxR
Output
Logic
S
R
Q
OCx
Output Enable
3
OCM<2:0>
Mode Select
OCFA
Comparator
0
0
OCTSEL
1
1
16
16
TMR2
Rollover
TMR3
Rollover
TMR3
TMR2
Note: An ‘x’ in a signal, register or bit name denotes the number of the output compare channels.
2008-2014 Microchip Technology Inc.
DS70000318G-page 193
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
application must disable the associated timer when
writing to the Output Compare Control registers to
Configure the Output Compare modes by setting the
avoid malfunctions.
14.1 Output Compare Modes
appropriate Output Compare Mode (OCM<2:0>) bits in
Note:
Refer to “Output Compare” (DS70209)
in the “dsPIC33F/PIC24H Family
the Output Compare Control (OCxCON<2:0>) register.
Table 14-1 lists the different bit settings for the Output
Compare modes. Figure 14-2 illustrates the output
compare operation for various modes. The user
Reference Manual” for OCxR and OCxRS
register restrictions.
TABLE 14-1: OUTPUT COMPARE MODES
OCM<2:0>
Mode
OCx Pin Initial State
OCx Interrupt Generation
111
PWM with Fault Protection
‘0’, if OCxR is zero
OCFA falling edge for OC1 to OC4
‘1’, if OCxR is non-zero
110
PWM without Fault Protection
‘0’, if OCxR is zero
No interrupt
‘1’, if OCxR is non-zero
101
100
011
010
001
000
Continuous Pulse
Delayed One-Shot
Toggle
0
0
OCx falling edge
OCx falling edge
Current output is maintained OCx rising and falling edge
Active-High One-Shot
Active-Low One-Shot
Module Disabled
1
OCx falling edge
OCx rising edge
0
Controlled by GPIO register
—
FIGURE 14-2:
OUTPUT COMPARE OPERATION
Output Compare
Mode Enabled
Timer is Reset on
Period Match
OCxRS
OCxR
TMRy
Active-Low One-Shot
(OCM<2:0> = 001)
Active-High One-Shot
(OCM<2:0> = 010)
Toggle
(OCM<2:0> = 011)
Delayed One-Shot
(OCM<2:0> = 100)
Continuous Pulse
(OCM<2:0> = 101)
PWM
(OCM<2:0> = 110or 111)
DS70000318G-page 194
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 14-1: OCxCON: OUTPUT COMPARE x CONTROL REGISTER (x = 1, 2)
U-0
—
U-0
—
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
OCSIDL
bit 15
bit 8
U-0
—
U-0
—
U-0
—
R-0, HC
OCFLT
R/W-0
R/W-0
OCM2
R/W-0
OCM1
R/W-0
OCM0
OCTSEL
bit 7
bit 0
Legend:
HC = Hardware Clearable bit
W = Writable bit
R = Readable bit
-n = Value at POR
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
‘1’ = Bit is set
bit 15-14
bit 13
Unimplemented: Read as ‘0’
OCSIDL: Stop Output Compare in Idle Mode Control bit
1= Output Compare x halts in CPU Idle mode
0= Output Compare x continues to operate in CPU Idle mode
bit 12-5
bit 4
Unimplemented: Read as ‘0’
OCFLT: PWM Fault Condition Status bit
1= PWM Fault condition has occurred (cleared in hardware only)
0= No PWM Fault condition has occurred (this bit is only used when OCM<2:0> = 111)
bit 3
OCTSEL: Output Compare Timer Select bit
1= Timer3 is the clock source for Output Compare x
0= Timer2 is the clock source for Output Compare x
bit 2-0
OCM<2:0>: Output Compare Mode Select bits
111= PWM mode on OCx, Fault pin is enabled
110= PWM mode on OCx, Fault pin is disabled
101= Initializes OCx pin low, generates continuous output pulses on OCx pin
100= Initializes OCx pin low, generates single output pulse on OCx pin
011= Compare event toggles OCx pin
010= Initializes OCx pin high, compare event forces OCx pin low
001= Initializes OCx pin low, compare event forces OCx pin high
000= Output compare channel is disabled
2008-2014 Microchip Technology Inc.
DS70000318G-page 195
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 196
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
• Independent Fault/Current-Limit inputs for each of
the eight PWM outputs
15.0 HIGH-SPEED PWM
Note 1: This data sheet summarizes the fea-
tures of the dsPIC33FJ06GS101/X02
and dsPIC33FJ16GSX02/X04 families
of devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “High- Speed PWM”
(DS70323) in the “dsPIC33F/PIC24H
Family Reference Manual”, which is
available on the Microchip web site
(www.microchip.com).
• Output override control
• Special Event Trigger
• PWM capture feature
• Prescaler for input clock
• Dual trigger from PWM to ADC
• PWMxH, PWMxL output pin swapping
• PWM4H, PWM4L pins remappable
• On-the-fly PWM frequency, duty cycle and
phase-shift changes
• Disabling of Individual PWM generators to reduce
power consumption
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
• Leading-Edge Blanking (LEB) functionality
Note:
Duty cycle, dead time, phase shift and
frequency resolution is 8.32 ns in
Center-Aligned PWM mode.
The
high-speed
PWM
module
on
the
Figure 15-1 conceptualizes the PWM module in a
simplified block diagram. Figure 15-2 illustrates how
the module hardware is partitioned for each PWM
output pair for the Complementary PWM mode. Each
functional unit of the PWM module is discussed in
subsequent sections.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 devices supports a wide variety of PWM modes
and output formats. This PWM module is ideal for
power conversion applications, such as:
• AC/DC Converters
• DC/DC Converters
• Power Factor Correction (PFC)
• Uninterruptible Power Supply (UPS)
• Inverters
The PWM module contains four PWM generators. The
module has up to eight PWM output pins: PWM1H,
PWM1L, PWM2H, PWM2L, PWM3H, PWM3L,
PWM4H and PWM4L. For complementary outputs,
these eight I/O pins are grouped into H/L pairs.
• Battery Chargers
• Digital Lighting
15.1 Features Overview
The high-speed PWM module incorporates the
following features:
• 2-4 PWM generators with 4-8 outputs
• Individual time base and duty cycle for each of the
eight PWM outputs
• Dead time for rising and falling edges:
• Duty cycle resolution of 1.04 ns
• Dead-time resolution of 1.04 ns
• Phase-shift resolution of 1.04 ns
• Frequency resolution of 1.04 ns
• PWM modes supported:
- Standard Edge-Aligned
- True Independent Output
- Complementary
- Center-Aligned
- Push-Pull
- Multiphase
- Variable Phase
- Fixed Off-Time
- Current Reset
- Current-Limit
2008-2014 Microchip Technology Inc.
DS70000318G-page 197
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Multiphase PWM is often used to improve DC/DC
15.2 Feature Description
Converter load transient response, and reduce the size
The PWM module is designed for applications that
of output filter capacitors and inductors. Multiple DC/
require:
DC Converters are often operated in parallel, but
• High-resolution at high PWM frequencies
phase-shifted in time. A single PWM output operating
• The ability to drive Standard, Edge-Aligned,
Center-Aligned Complementary mode, and
Push-Pull mode outputs
at 250 kHz has a period of 4 s, but an array of four
PWM channels, staggered by 1 s each, yields an
effective switching frequency of 1 MHz. Multiphase
PWM applications typically use
relationship.
a
fixed-phase
• The ability to create multiphase PWM outputs
For Center-Aligned mode, the duty cycle, period phase
and dead-time resolutions will be 8.32 ns.
Variable phase PWM is useful in Zero Voltage
Transition (ZVT) power converters. Here, the PWM
duty cycle is always 50%, and the power flow is
controlled by varying the relative phase shift between
the two PWM generators.
Two common, medium power converter topologies are
push-pull and half-bridge. These designs require the
PWM output signal to be switched between alternate
pins, as provided by the Push-Pull PWM mode.
Phase-shifted PWM describes the situation where
each PWM generator provides outputs, but the phase
relationship between the generator outputs is
specifiable and changeable.
DS70000318G-page 198
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 15-1:
SIMPLIFIED CONCEPTUAL BLOCK DIAGRAM OF HIGH-SPEED PWM
PWMCONx
Pin and Mode Control
LEBCONx
TRGCONx
Control for Blanking External Input Signals
ADC Trigger Control
Dead-Time Control
ALTDTRx, DTRx
PWM Enable and Mode Control
PTCON
MDC
Master Duty Cycle Register
PDC1
MUX
Latch
PWM GEN 1
PWM1H
PWM1L
Channel 1
Dead-Time Generator
Comparator
Timer
Phase
PDC2
MUX
Latch
PWM GEN 2
PWM2H
PWM2L
Channel 2
Dead-Time Generator
Comparator
Timer
Phase
PDC3
MUX
Latch
PWM GEN 3
PWM3H
PWM3L
Channel 3
Dead-Time Generator
Comparator
Timer
Phase
PDC4
PWM GEN 4
MUX
Latch
PWM4H(1)
PWM4L(1)
Channel 4
Dead-Time Generator
Comparator
Timer
Timer Period
Phase
(1)
FLTX
PTPER
Master Time Base
External Time Base
Synchronization
SYNCO(1)
PTMR
(1)
SYNCIX
Special Event
Postscaler
Special Event
Trigger
Comparator
Special Event
Comparison Value
Pin Override Control
SEVTCMP
IOCONx
Fault Mode and Pin Control
FCLCONx
Note 1: These pins are remappable.
2008-2014 Microchip Technology Inc.
DS70000318G-page 199
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 15-2:
PARTITIONED OUTPUT PAIR, COMPLEMENTARY PWM MODE
Phase Offset
TMR < PDC
PWM
M
U
X
Dead-Time
Logic
PWMXH
PWMXL
Timer/Counter
Override
Logic
Duty Cycle Comparator
M
U
X
Channel Override Values
PWM Duty Cycle Register
Fault Override Values
Fault Active
Fault Pin Assignment Logic
Fault Pin
• SDCx: PWMx Secondary Duty Cycle
Register(1,2)
15.3 Control Registers
The following registers control the operation of the
high-speed PWM module.
• SPHASEx: PWMx Secondary Phase-Shift
Register(1,2) (provides the local time base period
for PWMxL)
• PTCON: PWM Time Base Control Register
• PTCON2: PWM Clock Divider Select Register
• PTPER: PWM Master Time Base Register(1)
• TRGCONx: PWMx Trigger Control Register
• IOCONx: PWMx I/O Control Register
• SEVTCMP: PWM Special Event Compare
Register
• FCLCONx: PWMx Fault Current-Limit Control
Register
• MDC: PWM Master Duty Cycle Register(1,2)
• PWMCONx: PWMx Control Register
• TRIGx: PWMx Primary Trigger Compare Value
Register
• STRIGx: PWMx Secondary Trigger Compare
Value Register
• PDCx: PWMx Generator Duty Cycle Register(1,2)
• PHASEx: PWMx Primary Phase-Shift
Register(1,2) (provides the local time base period
for PWMxH)
• LEBCONx: Leading-Edge Blanking Control
Register(1)
• PWMCAPx: Primary PWMx Time Base Capture
Register
• DTRx: PWMx Dead-Time Register
• ALTDTRx: PWMx Alternate Dead-Time Register
DS70000318G-page 200
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-1: PTCON: PWM TIME BASE CONTROL REGISTER
R/W-0
PTEN
U-0
—
R/W-0
HS/HC-0
SESTAT
R/W-0
SEIEN
R/W-0
EIPU(1)
R/W-0
R/W-0
PTSIDL
SYNCPOL(1) SYNCOEN(1)
bit 15
bit 8
R/W-0
SYNCEN(1)
bit 7
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SYNCSRC1(1) SYNCSRC0(1) SEVTPS3(1) SEVTPS2(1) SEVTPS1(1) SEVTPS0(1)
bit 0
Legend:
HC = Hardware Clearable bit HS = Hardware Settable bit
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
PTEN: PWM Module Enable bit
1= PWM module is enabled
0= PWM module is disabled
bit 14
bit 13
Unimplemented: Read as ‘0’
PTSIDL: PWM Time Base Stop in Idle Mode bit
1= PWM time base halts in CPU Idle mode
0= PWM time base runs in CPU Idle mode
bit 12
bit 11
bit 10
bit 9
SESTAT: Special Event Interrupt Status bit
1= Special event interrupt is pending
0= Special event interrupt is not pending
SEIEN: Special Event Interrupt Enable bit
1= Special event interrupt is enabled
0= Special event interrupt is disabled
EIPU: Enable Immediate Period Updates bit(1)
1= Active Period register is updated immediately
0= Active Period register updates occur on PWM cycle boundaries
SYNCPOL: Synchronization Input/Output Polarity bit(1)
1= SYNCIx and SYNCO polarity is inverted (active-low)
0= SYNCIx and SYNCO are active-high
bit 8
SYNCOEN: Primary Time Base Sync Enable bit(1)
1= SYNCO output is enabled
0= SYNCO output is disabled
bit 7
SYNCEN: External Time Base Synchronization Enable bit(1)
1= External synchronization of primary time base is enabled
0= External synchronization of primary time base is disabled
bit 6
Unimplemented: Read as ‘0’
bit 5-4
SYNCSRC<1:0>: Synchronous Source Selection bits(1)
11= Reserved
10= Reserved
01= SYNCI2
00= SYNCI1
Note 1: These bits should be changed only when PTEN = 0. In addition, when using the SYNCIx feature, the user
application must program the Period register with a value that is slightly larger than the expected period of
the external synchronization input signal.
2008-2014 Microchip Technology Inc.
DS70000318G-page 201
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-1: PTCON: PWM TIME BASE CONTROL REGISTER (CONTINUED)
bit 3-0
SEVTPS<3:0>: PWM Special Event Trigger Output Postscaler Select bits(1)
1111= 1:16 Postscaler generates a Special Event Trigger trigger on every sixteenth compare match event
•
•
•
0001= 1:2 Postscaler generates a Special Event Trigger on every second compare match event
0000= 1:1 Postscaler generates a Special Event Trigger on every compare match event
Note 1: These bits should be changed only when PTEN = 0. In addition, when using the SYNCIx feature, the user
application must program the Period register with a value that is slightly larger than the expected period of
the external synchronization input signal.
DS70000318G-page 202
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-2: PTCON2: PWM CLOCK DIVIDER SELECT REGISTER
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
PCLKDIV<2:0>(1)
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-3
bit 2-0
Unimplemented: Read as ‘0’
PCLKDIV<2:0>: PWM Input Clock Prescaler (Divider) Select bits(1)
111= Reserved
110= Divide-by-64, maximum PWM timing resolution
101= Divide-by-32, maximum PWM timing resolution
100= Divide-by-16, maximum PWM timing resolution
011= Divide-by-8, maximum PWM timing resolution
010= Divide-by-4, maximum PWM timing resolution
001= Divide-by-2, maximum PWM timing resolution
000= Divide-by-1, maximum PWM timing resolution (power-on default)
Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
REGISTER 15-3: PTPER: PWM MASTER TIME BASE REGISTER(1)
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-0
R/W-1
PTPER <15:8>
bit 15
R/W-1
bit 7
bit 8
R/W-0
bit 0
R/W-1
R/W-1
R/W-1
R/W-1
R/W-0
PTPER <7:0>
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-0
PTPER<15:0>: PWM Master Time Base (PMTMR) Period Value bits
Note 1: The minimum value that can be loaded into the PTPER register is 0x0010 and the maximum value is
0xFFF8.
2008-2014 Microchip Technology Inc.
DS70000318G-page 203
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-4: SEVTCMP: PWM SPECIAL EVENT COMPARE REGISTER
R/W-0
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
bit 8
SEVTCMP <15:8>
R/W-0
R/W-0
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
SEVTCMP <7:3>
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-3
bit 2-0
SEVTCMP<12:0>: Special Event Compare Count Value bits
Unimplemented: Read as ‘0’
REGISTER 15-5: MDC: PWM MASTER DUTY CYCLE REGISTER(1,2)
R/W-0
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
bit 8
R/W-0
MDC<15:8>
R/W-0
R/W-0
R/W-0
MDC<7:0>
R/W-0
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-0
MDC<15:0>: Master PWM Duty Cycle Value bits
Note 1: The smallest pulse width that can be generated on the PWM output corresponds to a value of 0x0009,
while the maximum pulse width generated corresponds to a value of Period – 0x0008.
2: As the duty cycle gets closer to 0% or 100% of the PWM period (0 ns-40 ns, depending on the mode of
operation), the PWM duty cycle resolution will degrade from 1 LSB to 3 LSBs.
DS70000318G-page 204
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-6: PWMCONx: PWMx CONTROL REGISTER
HS/HC-0
FLTSTAT(1)
HS/HC-0
CLSTAT(1)
HS/HC-0
R/W-0
R/W-0
CLIEN
R/W-0
R/W-0
ITB(3)
R/W-0
MDCS(3)
TRGSTAT
FLTIEN
TRGIEN
bit 15
bit 8
R/W-0
DTC1
R/W-0
DTC0
U-0
—
U-0
—
U-0
—
R/W-0
CAM(2,3)
R/W-0
XPRES(4)
R/W-0
IUE
bit 7
bit 0
Legend:
HC = Hardware Clearable bit
W = Writable bit
HS = Hardware Settable bit
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
R = Readable bit
-n = Value at POR
‘1’ = Bit is set
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
FLTSTAT: Fault Interrupt Status bit(1)
1= Fault interrupt is pending
0= No Fault interrupt is pending; this bit is cleared by setting FLTIEN = 0
CLSTAT: Current-Limit Interrupt Status bit(1)
1= Current-limit interrupt is pending
0= No current-limit interrupt is pending; this bit is cleared by setting CLIEN = 0
TRGSTAT: Trigger Interrupt Status bit
1= Trigger interrupt is pending
0= No trigger interrupt is pending; this bit is cleared by setting TRGIEN = 0
FLTIEN: Fault Interrupt Enable bit
1= Fault interrupt is enabled
0= Fault interrupt is disabled and the FLTSTAT bit is cleared
CLIEN: Current-Limit Interrupt Enable bit
1= Current-limit interrupt is enabled
0= Current-limit interrupt is disabled and the CLSTAT bit is cleared
TRGIEN: Trigger Interrupt Enable bit
1= A trigger event generates an interrupt request
0= Trigger event interrupts are disabled and the TRGSTAT bit is cleared
ITB: Independent Time Base Mode bit(3)
1= PHASEx/SPHASEx register provides time base period for this PWM generator
0= PTPER register provides timing for this PWM generator
bit 8
MDCS: Master Duty Cycle Register Select bit(3)
1= MDC register provides duty cycle information for this PWM generator
0= PDCx/SDCx register provides duty cycle information for this PWM generator
bit 7-6
DTC<1:0>: Dead-Time Control bits
11= Reserved
10= Dead-time function is disabled
01= Negative dead time is actively applied for all output modes
00= Positive dead time is actively applied for all output modes
bit 5-3
Unimplemented: Read as ‘0’
Note 1: Software must clear the interrupt status here and the corresponding IFSx bit in the interrupt controller.
2: The Independent Time Base mode (ITB = 1) must be enabled to use Center-Aligned mode. If ITB = 0, the
CAM bit is ignored.
3: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
4: To operate in External Period Reset mode, configure FCLCONx<CLMOD> = 0and PWMCONx<ITB> = 1.
2008-2014 Microchip Technology Inc.
DS70000318G-page 205
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-6: PWMCONx: PWMx CONTROL REGISTER (CONTINUED)
bit 2
bit 1
CAM: Center-Aligned Mode Enable bit(2,3)
1= Center-Aligned mode is enabled
0= Center-Aligned mode is disabled
XPRES: External PWM Reset Control bit(4)
1= Current-limit source resets the time base for this PWM generator if it is in Independent Time
Base (ITB) mode
0= External pins do not affect PWM time base
bit 0
IUE: Immediate Update Enable bit
1= Updates to the active MDC/PDCx/SDCx registers are immediate
0= Updates to the active MDC/PDCx/SDCx registers are synchronized to the PWM time base
Note 1: Software must clear the interrupt status here and the corresponding IFSx bit in the interrupt controller.
2: The Independent Time Base mode (ITB = 1) must be enabled to use Center-Aligned mode. If ITB = 0, the
CAM bit is ignored.
3: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
4: To operate in External Period Reset mode, configure FCLCONx<CLMOD> = 0and PWMCONx<ITB> = 1.
DS70000318G-page 206
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-7: PDCx: PWMx GENERATOR DUTY CYCLE REGISTER(1,2)
R/W-0
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
bit 8
R/W-0
PDCx<15:8>
R/W-0
R/W-0
R/W-0
PDCx<7:0>
R/W-0
R/W-0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-0
PDCx<15:0>: PWM Generator # Duty Cycle Value bits
Note 1: In Independent PWM mode, the PDCx register controls the PWMxH duty cycle only. In Complementary,
Redundant and Push-Pull PWM modes, the PDCx register controls the duty cycle of both the PWMxH and
PWMxL. The smallest pulse width that can be generated on the PWM output corresponds to a value of
0x0009, while the maximum pulse width generated corresponds to a value of Period-0x0008.
2: As the duty cycle gets closer to 0% or 100% of the PWM period (0 ns-40 ns, depending on the mode of
operation), the PWM duty cycle resolution will degrade from 1 LSB to 3 LSBs.
REGISTER 15-8: SDCx: PWMx SECONDARY DUTY CYCLE REGISTER(1,2)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SDCx<15:8>
bit 15
R/W-0
bit 7
bit 8
R/W-0
bit 0
R/W-0
R/W-0
R/W-0
SDCx<7:0>
R/W-0
R/W-0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-0
SDCx<15:0>: Secondary Duty Cycle for PWMxL Output Pin bits
Note 1: The SDCx register is used in Independent PWM mode only. When used in Independent PWM mode, the
SDCx register controls the PWMxL duty cycle. The smallest pulse width that can be generated on the
PWM output corresponds to a value of 0x0009, while the maximum pulse width generated corresponds to
a value of Period-0x0008.
2: As the duty cycle gets closer to 0% or 100% of the PWM period (0 ns-40 ns, depending on the mode of
operation), the PWM duty cycle resolution will degrade from 1 LSB to 3 LSBs.
2008-2014 Microchip Technology Inc.
DS70000318G-page 207
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-9: PHASEx: PWMx PRIMARY PHASE-SHIFT REGISTER(1,2)
R/W-0
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
bit 8
R/W-0
PHASEx<15:8>
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PHASEx<7:0>
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-0
PHASEx<15:0>: PWM Phase-Shift Value or Independent Time Base Period for this PWM Generator bits
Note 1: If PWMCONx<ITB> = 0, the following applies based on the mode of operation:
• Complementary, Redundant and Push-Pull Output mode (PMOD<1:0> (IOCONx<11:10>) = 00, 01or 10);
PHASEx<15:0> = Phase-shift value for PWMxH and PWMxL outputs
• True Independent Output mode (PMOD<1:0> (IOCONx<11:10>) = 11);
PHASEx<15:0> = Phase-shift value for PWMxL only
2: If PWMCONx<ITB> = 1, the following applies based on the mode of operation:
• Complementary, Redundant, and Push-Pull Output mode (PMOD<1:0> (IOCONx<11:10>) = 00, 01or
10); PHASEx<15:0> = Independent Time Base period value for PWMxH and PWMxL
• True Independent Output mode (PMOD<1:0> (IOCONx<11:10>) = 11); PHASEx<15:0> = Independent
Time Base period value for PWMxL only
• The smallest pulse width that can be generated on the PWM output corresponds to a value of 0x0008,
while the maximum pulse width generated corresponds to a value of Period – 0x0008.
DS70000318G-page 208
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-10: SPHASEx: PWMx SECONDARY PHASE-SHIFT REGISTER(1,2)
R/W-0
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
bit 8
R/W-0
SPHASEx<15:8>
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
SPHASEx<7:0>
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-0
SPHASEx<15:0>: Secondary Phase Offset for PWMxL Output Pin bits
(used in Independent PWM mode only)
Note 1: If PWMCONx<ITB> = 0, the following applies based on the mode of operation:
• Complementary, Redundant and Push-Pull Output mode (PMOD<1:0> (IOCONx<11:10>) = 00, 01
or 10); SPHASEx<15:0> = Not used
• True Independent Output mode (IOCONx<PMOD> = 11);
PHASEx<15:0> = Phase-shift value for PWMxL only
2: If PWMCONx<ITB> = 1, the following applies based on the mode of operation:
• Complementary, Redundant and Push-Pull Output mode (IOCONx<PMOD> = 00, 01, or 10);
SPHASEx<15:0> = Not used
• True Independent Output mode (PMOD<1:0> (IOCONx<11:10>) = 11);
PHASEx<15:0> = Independent Time Base period value for PWMxL only
2008-2014 Microchip Technology Inc.
DS70000318G-page 209
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
.
REGISTER 15-11: DTRx: PWMx DEAD-TIME REGISTER
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
bit 8
R/W-0
DTRx<13:8>
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
DTRx<7:0>
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-0
Unimplemented: Read as ‘0’
DTRx<13:0>: Unsigned 14-Bit Dead-Time Value for PWMx Dead-Time Unit bits
REGISTER 15-12: ALTDTRx: PWMx ALTERNATE DEAD-TIME REGISTER
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ALTDTRx<13:8>
bit 15
R/W-0
bit 7
bit 8
R/W-0
bit 0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ALTDTR <7:0>
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-14
bit 13-0
Unimplemented: Read as ‘0’
ALTDTRx<13:0>: Unsigned 14-Bit Dead-Time Value for PWMx Dead-Time Unit bits
DS70000318G-page 210
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-13: TRGCONx: PWMx TRIGGER CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
TRGDIV3
TRGDIV2
TRGDIV1
TRGDIV0
bit 15
bit 8
R/W-0
DTM(1)
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TRGSTRT5 TRGSTRT4 TRGSTRT3 TRGSTRT2 TRGSTRT1 TRGSTRT0
bit 0
bit 7
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15-12
TRGDIV<3:0>: Trigger # Output Divider bits
1111= Trigger output for every 16th trigger event
1110= Trigger output for every 15th trigger event
1101= Trigger output for every 14th trigger event
1100= Trigger output for every 13th trigger event
1011= Trigger output for every 12th trigger event
1010= Trigger output for every 11th trigger event
1001= Trigger output for every 10th trigger event
1000= Trigger output for every 9th trigger event
0111= Trigger output for every 8th trigger event
0110= Trigger output for every 7th trigger event
0101= Trigger output for every 6th trigger event
0100= Trigger output for every 5th trigger event
0011= Trigger output for every 4th trigger event
0010= Trigger output for every 3rd trigger event
0001= Trigger output for every 2nd trigger event
0000= Trigger output for every trigger event
bit 11-8
bit 7
Unimplemented: Read as ‘0’
DTM: Dual Trigger Mode bit(1)
1= Secondary trigger event is combined with the primary trigger event to create the PWM trigger.
0= Secondary trigger event is not combined with the primary trigger event to create the PWM trigger;
two separate PWM triggers are generated
bit 6
Unimplemented: Read as ‘0’
bit 5-0
TRGSTRT<5:0>: Trigger Postscaler Start Enable Select bits
111111= Wait 63 PWM cycles before generating the first trigger event after the module is enabled
•
•
•
000010= Wait 1 PWM cycles before generating the first trigger event after the module is enabled
000001= Wait 1 PWM cycle before generating the first trigger event after the module is enabled
000000= Wait 0 PWM cycles before generating the first trigger event after the module is enabled
Note 1: The secondary generator cannot generate PWM trigger interrupts.
2008-2014 Microchip Technology Inc.
DS70000318G-page 211
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-14: IOCONx: PWMx I/O CONTROL REGISTER
R/W-0
PENH
R/W-0
PENL
R/W-0
POLH
R/W-0
POLL
R/W-0
PMOD1(1)
R/W-0
PMOD0(1)
R/W-0
R/W-0
OVRENH
OVRENL
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CLDAT0(2)
R/W-0
SWAP
R/W-0
OVRDAT1
OVRDAT0
FLTDAT1(2) FLTDAT0(2) CLDAT1(2)
OSYNC
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 15
PENH: PWMH Output Pin Ownership bit
1= PWM module controls the PWMxH pin
0= GPIO module controls the PWMxH pin
bit 14
PENL: PWML Output Pin Ownership bit
1= PWM module controls the PWMxL pin
0= GPIO module controls the PWMxL pin
bit 13
POLH: PWMH Output Pin Polarity bit
1= PWMxH pin is active-low
0= PWMxH pin is active-high
bit 12
POLL: PWML Output Pin Polarity bit
1= PWMxL pin is active-low
0= PWMxL pin is active-high
bit 11-10
PMOD<1:0>: PWM # I/O Pin Mode bits(1)
11= PWM I/O pin pair is in the True Independent Output mode
10= PWM I/O pin pair is in the Push-Pull Output mode
01= PWM I/O pin pair is in the Redundant Output mode
00= PWM I/O pin pair is in the Complementary Output mode
bit 9
OVRENH: Override Enable for PWMxH Pin bit
1= OVRDAT<1> provides data for output on the PWMxH pin
0= PWM generator provides data for the PWMxH pin
bit 8
OVRENL: Override Enable for PWMxL Pin bit
1= OVRDAT<0> provides data for output on the PWMxL pin
0= PWM generator provides data for the PWMxL pin
bit 7-6
bit 5-4
OVRDAT<1:0>: Data for PWMxH and PWMxL Pins if Override is Enabled bits
If OVERENH = 1, then OVRDAT<1> provides data for PWMxH
If OVERENL = 1, then OVRDAT<0> provides data for PWMxL
FLTDAT<1:0>: State for PWMxH and PWMxL Pins if FLTMOD is Enabled bits(2)
FCLCONx<IFLTMOD> = 0: Normal Fault mode:
If Fault is active, then FLTDAT<1> provides the state for PWMxH
If Fault is active, then FLTDAT<0> provides the state for PWMxL
FCLCONx<IFLTMOD> = 1: Independent Fault mode:
If current-limit is active, then FLTDAT<1> provides data for PWMxH
If Fault is active, then FLTDAT<0> provides the state for PWMxL
Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
2: The state represents the active/inactive state of the PWM module depending on the POLH and POLL bit
settings.
DS70000318G-page 212
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-14: IOCONx: PWMx I/O CONTROL REGISTER (CONTINUED)
bit 3-2
CLDAT<1:0>: State for PWMxH and PWMxL Pins if CLMODE is Enabled bits(2)
FCLCONx<IFLTMOD> = 0: Normal Fault mode:
If current-limit is active, then CLDAT<1> provides the state for PWMxH
If current-limit is active, then CLDAT<0> provides the state for PWMxL
FCLCONx<IFLTMOD> = 1: Independent Fault mode:
CLDAT<1:0> bits are ignored.
bit 1
bit 0
SWAP<1:0>: Swap PWMxH and PWMxL pins
1= PWMxH output signal is connected to the PWMxL pin and the PWMxL signal is connected to the
PWMxH pins
0= PWMxH and PWMxL pins are mapped to their respective pins
OSYNC: Output Override Synchronization bit
1= Output overrides via the OVRDAT<1:0> bits are synchronized to the PWM time base
0= Output overrides via the OVDDAT<1:0> bits occur on the next CPU clock boundary
Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
2: The state represents the active/inactive state of the PWM module depending on the POLH and POLL bit
settings.
2008-2014 Microchip Technology Inc.
DS70000318G-page 213
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-15: FCLCONx: PWMx FAULT CURRENT-LIMIT CONTROL REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IFLTMOD
CLSRC4(2,3) CLSRC3(2,3) CLSRC2(2,3) CLSRC1(2,3) CLSRC0(2,3)
CLPOL(1)
CLMOD
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
FLTSRC4(2,3) FLTSRC3(2,3) FLTSRC2(2,3) FLTSRC1(2,3) FLTSRC0(2,3) FLTPOL(1)
FLTMOD1
FLTMOD0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
IFLTMOD: Independent Fault Mode Enable bit
1= Independent Fault mode: Current-limit input maps FLTDAT1 to PWMxH output and the Fault input
maps FLTDAT0 to the PWMxL output. The CLDAT<1:0> bits are not used for override functions.
0= Normal Fault mode: Current-limit feature maps CLDAT<1:0> bits to the PWMxH and PWMxL
outputs. The PWM Fault feature maps FLTDAT<1:0> to the PWMxH and PWMxL outputs.
bit 14-10
CLSRC<4:0>: Current-Limit Control Signal Source Select for PWM # Generator bits(2,3)
11111= Reserved
•
•
•
01000= Reserved
00111= Fault 8
00110= Fault 7
00101= Fault 6
00100= Fault 5
00011= Fault 4
00010= Fault 3
00001= Fault 2
00000= Fault 1
bit 9
bit 8
CLPOL: Current-Limit Polarity for PWM Generator # bit(1)
1= The selected current-limit source is active-low
0= The selected current-limit source is active-high
CLMOD: Current-Limit Mode Enable bit for PWM Generator # bit
1= Current-limit function is enabled
0= Current-limit function is disabled
Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
2: When Independent Fault mode is enabled (IFLTMOD = 1), and Fault 1 is used for Current-Limit mode
(CLSRC<4:0> = b0000), the Fault Control Source Select bits (FLTSRC<4:0>) should be set to an unused
Fault source to prevent Fault 1 from disabling both the PWMxL and PWMxH outputs.
3: When Independent Fault mode is enabled (IFLTMOD = 1) and Fault 1 is used for Fault mode
(FLTSRC<4:0> = b0000), the Current-Limit Control Source Select bits (CLSRC<4:0>) should be set to an
unused current-limit source to prevent the current-limit source from disabling both the PWMxH and
PWMxL outputs.
DS70000318G-page 214
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-15: FCLCONx: PWMx FAULT CURRENT-LIMIT CONTROL REGISTER (CONTINUED)
bit 7-3
FLTSRC<4:0>: Fault Control Signal Source Select for PWM Generator # bits(2,3)
11111= Reserved
•
•
•
01000= Reserved
00111= Fault 8
00110= Fault 7
00101= Fault 6
00100= Fault 5
00011= Fault 4
00010= Fault 3
00001= Fault 2
00000= Fault 1
bit 2
FLTPOL: Fault Polarity for PWM Generator # bit(1)
1= The selected Fault source is active-low
0= The selected Fault source is active-high
bit 1-0
FLTMOD<1:0>: Fault Mode for PWM Generator # bits
11= Fault input is disabled
10= Reserved
01= The selected Fault source forces the PWMxH and PWMxL pins to FLTDAT values (cycle)
00= The selected Fault source forces the PWMxH and PWMxL pins to FLTDAT values (latched condition)
Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
2: When Independent Fault mode is enabled (IFLTMOD = 1), and Fault 1 is used for Current-Limit mode
(CLSRC<4:0> = b0000), the Fault Control Source Select bits (FLTSRC<4:0>) should be set to an unused
Fault source to prevent Fault 1 from disabling both the PWMxL and PWMxH outputs.
3: When Independent Fault mode is enabled (IFLTMOD = 1) and Fault 1 is used for Fault mode
(FLTSRC<4:0> = b0000), the Current-Limit Control Source Select bits (CLSRC<4:0>) should be set to an
unused current-limit source to prevent the current-limit source from disabling both the PWMxH and
PWMxL outputs.
2008-2014 Microchip Technology Inc.
DS70000318G-page 215
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-16: TRIGx: PWMx PRIMARY TRIGGER COMPARE VALUE REGISTER
R/W-0
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
bit 8
TRGCMP<15:8>
R/W-0
R/W-0
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
TRGCMP<7:3>
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-3
bit 2-0
TRGCMP<15:3>: Trigger Control Value bits
When primary PWM functions in the local time base, this register contains the compare values that can
trigger the ADC module.
Unimplemented: Read as ‘0’
REGISTER 15-17: STRIGx: PWMx SECONDARY TRIGGER COMPARE VALUE REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
STRGCMP<15:8>
bit 15
R/W-0
bit 7
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
STRGCMP<7:3>
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-3
bit 2-0
STRGCMP<15:3>: Secondary Trigger Control Value bits
When secondary PWM functions in the local time base, this register contains the compare values that
can trigger the ADC module.
Unimplemented: Read as ‘0’
DS70000318G-page 216
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-18: LEBCONx: LEADING-EDGE BLANKING CONTROL REGISTER(1)
R/W-0
PHR
R/W-0
PHF
R/W-0
PLR
R/W-0
PLF
R/W-0
R/W-0
R/W-0
LEB6
R/W-0
LEB5
FLTLEBEN
CLLEBEN
bit 15
bit 8
R/W-0
LEB4
R/W-0
LEB3
R/W-0
LEB2
R/W-0
LEB1
R/W-0
LEB0
U-0
—
U-0
—
U-0
—
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
PHR: PWMxH Rising Edge Trigger Enable bit
1= Rising edge of PWMxH will trigger the LEB counter
0= LEB ignores the rising edge of PWMxH
PHF: PWMH Falling Edge Trigger Enable bit
1= Falling edge of PWMxH will trigger the LEB counter
0= LEB ignores the falling edge of PWMxH
PLR: PWML Rising Edge Trigger Enable bit
1= Rising edge of PWMxL will trigger the LEB counter
0= LEB ignores the rising edge of PWMxL
PLF: PWML Falling Edge Trigger Enable bit
1= Falling edge of PWMxL will trigger the LEB counter
0= LEB ignores the falling edge of PWMxL
FLTLEBEN: Fault Input LEB Enable bit
1= Leading-Edge Blanking is applied to selected Fault input
0= Leading-Edge Blanking is not applied to selected Fault input
CLLEBEN: Current-Limit LEB Enable bit
1= Leading-Edge Blanking is applied to selected current-limit input
0= Leading-Edge Blanking is not applied to selected current-limit input
bit 9-3
bit 2-0
LEB<6:0>: Leading-Edge Blanking for Current-Limit and Fault Inputs bits
The value is 8.32 nsec increments.
Unimplemented: Read as ‘0’
Note 1: Configure this register in word format.
2008-2014 Microchip Technology Inc.
DS70000318G-page 217
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 15-19: PWMCAPx: PRIMARY PWMx TIME BASE CAPTURE REGISTER
R-0
bit 15
R-0
R-0
R-0
R-0
R-0
R-0
R-0
R-0
PWMCAP<15:8>(1,2)
bit 8
bit 0
R-0
R-0
R-0
R-0
U-0
—
U-0
—
U-0
—
PWMCAP<7:3>(1,2)
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-3
bit 2-0
PWMCAP<15:3>: Captured PWM Time Base Value bits(1,2)
The value in this register represents the captured PWM time base value when a leading edge is
detected on the current-limit input.
Unimplemented: Read as ‘0’
Note 1: The capture feature is only available on the primary output (PWMxH).
2: This feature is active only after LEB processing on the current-limit input signal is complete.
DS70000318G-page 218
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The Serial Peripheral Interface (SPI) module is a
16.0 SERIAL PERIPHERAL
synchronous serial interface useful for communicating
INTERFACE (SPI)
with other peripheral or microcontroller devices. These
peripheral devices can be serial EEPROMs, shift
Note 1: This data sheet summarizes the features
registers, display drivers, Analog-to-Digital Converters
of the dsPIC33FJ06GS101/X02 and
and so on. The SPI module is compatible with SPI and
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
SIOP from Motorola®.
comprehensive reference source. To
complement the information in this data
sheet, refer to “Serial Peripheral
Interface (SPI)” (DS70206) in the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available on the
Microchip web site (www.microchip.com).
The SPI module consists of a 16-bit shift register,
SPIxSR (where x = 1), used for shifting data in and out,
and a buffer register, SPIxBUF. A control register,
SPIxCON, configures the module. Additionally, a status
register, SPIxSTAT, indicates status conditions.
The serial interface consists of the following four pins:
• SDIx (Serial Data Input)
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
• SDOx (Serial Data Output)
• SCKx (Shift Clock Input Or Output)
• SSx (Active-Low Slave Select).
In Master mode operation, SCK is a clock output; in
Slave mode, it is a clock input.
FIGURE 16-1:
SPIx MODULE BLOCK DIAGRAM
SCKx
SSx
1:1 to 1:8
Secondary
Prescaler
1:1/4/16/64
Primary
Prescaler
FCY
Sync
Control
Select
Edge
Control
Clock
SPIxCON1<1:0>
SPIxCON1<4:2>
Shift Control
SDOx
SDIx
Enable
Master Clock
bit 0
SPIxSR
Transfer
Transfer
SPIxRXB SPIxTXB
SPIxBUF
Write SPIxBUF
Read SPIxBUF
16
Internal Data Bus
2008-2014 Microchip Technology Inc.
DS70000318G-page 219
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 16-1: SPIxSTAT: SPIx STATUS AND CONTROL REGISTER
R/W-0
SPIEN
U-0
—
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
SPISIDL
bit 15
bit 8
U-0
—
R/C-0
U-0
—
U-0
—
U-0
—
U-0
—
R-0
R-0
SPIROV
SPITBF
SPIRBF
bit 0
bit 7
Legend:
C = Clearable bit
W = Writable bit
‘1’ = Bit is set
R = Readable bit
-n = Value at POR
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
SPIEN: SPIx Enable bit
1= Enables module and configures SCKx, SDOx, SDIx and SSx as serial port pins
0= Disables module
bit 14
bit 13
Unimplemented: Read as ‘0’
SPISIDL: SPIx Stop in Idle Mode bit
1= Discontinues module operation when device enters Idle mode
0= Continues module operation in Idle mode
bit 12-7
bit 6
Unimplemented: Read as ‘0’
SPIROV: SPIx Receive Overflow Flag bit
1= A new byte/word is completely received and discarded. The user software has not read the
previous data in the SPIxBUF register.
0= No overflow has occurred
bit 5-2
bit 1
Unimplemented: Read as ‘0’
SPITBF: SPIx Transmit Buffer Full Status bit
1= Transmit not yet started, SPIxTXB is full
0= Transmit started, SPIxTXB is empty. Automatically set in hardware when CPU writes the SPIxBUF
location, loading SPIxTXB. Automatically cleared in hardware when the SPIx module transfers
data from SPIxTXB to SPIxSR.
bit 0
SPIRBF: SPIx Receive Buffer Full Status bit
1= Receive complete, SPIxRXB is full
0= Receive is not complete, SPIxRXB is empty. Automatically set in hardware when SPIx transfers
data from SPIxSR to SPIxRXB. Automatically cleared in hardware when core reads the SPIxBUF
location, reading SPIxRXB.
DS70000318G-page 220
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 16-2: SPIXCON1: SPIx CONTROL REGISTER 1
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
SMP
R/W-0
CKE(1)
DISSCK
DISSDO
MODE16
bit 15
bit 8
R/W-0
SSEN(3)
R/W-0
CKP
R/W-0
R/W-0
SPRE2(2)
R/W-0
SPRE1(2)
R/W-0
SPRE0(2)
R/W-0
PPRE1(2)
R/W-0
PPRE0(2)
MSTEN
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-13
bit 12
Unimplemented: Read as ‘0’
DISSCK: Disable SCKx Pin bit (SPI Master modes only)
1= Internal SPI clock is disabled; pin functions as I/O
0= Internal SPI clock is enabled
bit 11
bit 10
bit 9
DISSDO: Disable SDOx Pin bit
1= SDOx pin is not used by module; pin functions as I/O
0= SDOx pin is controlled by the module
MODE16: Word/Byte Communication Select bit
1= Communication is word-wide (16 bits)
0= Communication is byte-wide (8 bits)
SMP: SPIx Data Input Sample Phase bit
Master mode:
1= Input data sampled at end of data output time
0= Input data sampled at middle of data output time
Slave mode:
SMP must be cleared when SPIx is used in Slave mode.
bit 8
bit 7
bit 6
bit 5
CKE: SPIx Clock Edge Select bit(1)
1= Serial output data changes on transition from active clock state to Idle clock state (see bit 6)
0= Serial output data changes on transition from Idle clock state to active clock state (see bit 6)
SSEN: Slave Select Enable bit (Slave mode)(3)
1= SSx pin is used for Slave mode
0= SSx pin is not used by module; pin controlled by port function
CKP: Clock Polarity Select bit
1= Idle state for clock is a high level; active state is a low level
0= Idle state for clock is a low level; active state is a high level
MSTEN: Master Mode Enable bit
1= Master mode
0= Slave mode
Note 1: The CKE bit is not used in the Framed SPI modes. Program this bit to ‘0’ for the Framed SPI modes
(FRMEN = 1).
2: Do not set both primary and secondary prescalers to a value of 1:1.
3: This bit must be cleared when FRMEN = 1.
2008-2014 Microchip Technology Inc.
DS70000318G-page 221
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 16-2: SPIXCON1: SPIx CONTROL REGISTER 1 (CONTINUED)
bit 4-2
SPRE<2:0>: Secondary Prescale bits (Master mode)(2)
111= Secondary prescale 1:1
110= Secondary prescale 2:1
•
•
•
000= Secondary prescale 8:1
bit 1-0
PPRE<1:0>: Primary Prescale bits (Master mode)(2)
11= Primary prescale 1:1
10= Primary prescale 4:1
01= Primary prescale 16:1
00= Primary prescale 64:1
Note 1: The CKE bit is not used in the Framed SPI modes. Program this bit to ‘0’ for the Framed SPI modes
(FRMEN = 1).
2: Do not set both primary and secondary prescalers to a value of 1:1.
3: This bit must be cleared when FRMEN = 1.
DS70000318G-page 222
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 16-3: SPIxCON2: SPIx CONTROL REGISTER 2
R/W-0
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
FRMEN
SPIFSD
FRMPOL
bit 15
bit 8
bit 0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
U-0
—
FRMDLY
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
bit 14
bit 13
FRMEN: Framed SPIx Support bit
1= Framed SPIx support is enabled (SSx pin used as frame sync pulse input/output)
0= Framed SPIx support is disabled
SPIFSD: SPIx Frame Sync Pulse Direction Control bit
1= Frame sync pulse input (slave)
0= Frame sync pulse output (master)
FRMPOL: Frame Sync Pulse Polarity bit
1= Frame sync pulse is active-high
0= Frame sync pulse is active-low
bit 12-2
bit 1
Unimplemented: Read as ‘0’
FRMDLY: Frame Sync Pulse Edge Select bit
1= Frame sync pulse coincides with first bit clock
0= Frame sync pulse precedes first bit clock
bit 0
Unimplemented: This bit must not be set to ‘1’ by the user application
2008-2014 Microchip Technology Inc.
DS70000318G-page 223
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 224
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The I2C module has a 2-pin interface, where:
17.0 INTER-INTEGRATED CIRCUIT
2
• The SCLx pin is clock
• The SDAx pin is data
(I C™)
Note 1: This data sheet summarizes the features
The I2C module offers the following key features:
of the dsPIC33FJ06GS101/X02 and
• I2C interface supporting both Master and Slave
modes of operation
• I2C Slave mode supports 7-bit and 10-bit addressing
• I2C Master mode supports 7-bit and 10-bit
addressing
• I2C port allows bidirectional transfers between
master and slaves
• Serial clock synchronization for I2C port can be used
as a handshake mechanism to suspend and resume
serial transfer (SCLREL control)
• I2C supports multi-master operation, detects bus
collision and arbitrates accordingly
dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this
data sheet, refer to “Inter-Integrated
Circuit (I2C™)” (DS70000195) in the
“dsPIC33/PIC24 Family Reference Man-
ual”, which is available on the Microchip
web site (www.microchip.com).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
17.1 Operating Modes
The hardware fully implements all the master and slave
functions of the I2C Standard and Fast mode
specifications, as well as 7-bit and 10-bit addressing.
The Inter-Integrated Circuit (I2C) module provides
complete hardware support for both Slave and
Multi-Master modes of the I2C serial communication
standard with a 16-bit interface.
The I2C module can operate either as a slave or a
master on an I2C bus.
The following types of I2C operation are supported:
• I2C slave operation with 7-bit addressing
• I2C slave operation with 10-bit addressing
• I2C master operation with 7-bit or 10-bit addressing
2008-2014 Microchip Technology Inc.
DS70000318G-page 225
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 17-1:
I2Cx BLOCK DIAGRAM (X = 1)
Internal
Data Bus
I2CxRCV
Read
Shift
Clock
SCLx
SDAx
I2CxRSR
LSb
Address Match
Write
Read
Match Detect
I2CxMSK
Write
Read
I2CxADD
Start and Stop
Bit Detect
Write
Start and Stop
Bit Generation
I2CxSTAT
I2CxCON
Read
Write
Collision
Detect
Acknowledge
Generation
Read
Clock
Stretching
Write
Read
I2CxTRN
LSb
Shift Clock
Reload
Control
Write
Read
BRG Down Counter
TCY/2
I2CxBRG
DS70000318G-page 226
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
2
17.2 I C Registers
I2CxCON and I2CxSTAT are control and status
registers. The I2CxCON register is readable and
writable. The lower six bits of I2CxSTAT are read-only.
The remaining bits of the I2CxSTAT are read/write:
• I2CxRSR is the shift register used for shifting data
internal to the module and the user application
has no access to it
• I2CxRCV is the receive buffer and the register to
which data bytes are written, or from which data
bytes are read
• I2CxTRN is the transmit register to which bytes
are written during a transmit operation
• The I2CxADD register holds the slave address
• A status bit, ADD10, indicates 10-Bit Addressing
mode
• The I2CxBRG acts as the Baud Rate Generator
(BRG) reload value
In receive operations, I2CxRSR and I2CxRCV together
form a double-buffered receiver. When I2CxRSR
receives a complete byte, it is transferred to I2CxRCV,
and an interrupt pulse is generated.
2008-2014 Microchip Technology Inc.
DS70000318G-page 227
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 17-1: I2CxCON: I2Cx CONTROL REGISTER
R/W-0
I2CEN
U-0
—
R/W-0
R/W-1, HC
SCLREL
R/W-0
R/W-0
A10M
R/W-0
R/W-0
SMEN
I2CSIDL
IPMIEN
DISSLW
bit 15
bit 8
R/W-0
GCEN
R/W-0
R/W-0
R/W-0, HC R/W-0, HC
ACKEN RCEN
R/W-0, HC
PEN
R/W-0, HC
RSEN
R/W-0, HC
SEN
STREN
ACKDT
bit 7
bit 0
Legend:
U = Unimplemented bit, read as ‘0’
R = Readable bit
W = Writable bit
‘1’ = Bit is set
HC = Hardware Clearable bit
‘0’ = Bit is cleared
-n = Value at POR
x = Bit is unknown
bit 15
I2CEN: I2Cx Enable bit
1= Enables the I2Cx module, and configures the SDAx and SCLx pins as serial port pins
0= Disables the I2Cx module; all I2C™ pins are controlled by port functions.
bit 14
bit 13
Unimplemented: Read as ‘0’
I2CSIDL: I2Cx Stop in Idle Mode bit
1= Discontinues module operation when device enters an Idle mode
0= Continues module operation in Idle mode
bit 12
SCLREL: SCLx Release Control bit (when operating as I2C slave)
1= Releases SCLx clock
0= Holds SCLx clock low (clock stretch)
If STREN = 1:
Bit is R/W (i.e., software can write ‘0’ to initiate stretch and write ‘1’ to release clock). Hardware clear
at beginning of slave transmission. Hardware clear at end of slave reception.
If STREN = 0:
Bit is R/S (i.e., software can only write ‘1’ to release clock). Hardware clear at beginning of slave
transmission.
bit 11
bit 10
bit 9
IPMIEN: Intelligent Peripheral Management Interface (IPMI) Enable bit
1= IPMI mode is enabled; all addresses are Acknowledged
0= IPMI mode is disabled
A10M: 10-Bit Slave Address bit
1= I2CxADD is a 10-bit slave address
0= I2CxADD is a 7-bit slave address
DISSLW: Disable Slew Rate Control bit
1= Slew rate control is disabled
0= Slew rate control is enabled
bit 8
SMEN: SMBus Input Levels bit
1= Enables I/O pin thresholds compliant with SMBus specification
0= Disables SMBus input thresholds
bit 7
GCEN: General Call Enable bit (when operating as I2C slave)
1= Enables interrupt when a general call address is received in the I2CxRSR (module is enabled for
reception)
0= General call address is disabled
bit 6
STREN: SCLx Clock Stretch Enable bit (when operating as I2C slave)
Used in conjunction with the SCLREL bit.
1= Enables software or receive clock stretching
0= Disables software or receive clock stretching
DS70000318G-page 228
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 17-1: I2CxCON: I2Cx CONTROL REGISTER (CONTINUED)
bit 5
ACKDT: Acknowledge Data bit (when operating as I2C master, applicable during master receive)
Value that is transmitted when the software initiates an Acknowledge sequence.
1= Sends NACK during Acknowledge
0= Sends ACK during Acknowledge
bit 4
ACKEN: Acknowledge Sequence Enable bit
(when operating as I2C master, applicable during master receive)
1= Initiates Acknowledge sequence on SDAx and SCLx pins and transmits the ACKDT data bit.
Hardware is clear at end of master Acknowledge sequence.
0= Acknowledge sequence is not in progress
bit 3
bit 2
bit 1
RCEN: Receive Enable bit (when operating as I2C master)
1= Enables Receive mode for I2C. Hardware is clear at end of eighth bit of master receive data byte.
0= Receive sequence is not in progress
PEN: Stop Condition Enable bit (when operating as I2C master)
1= Initiates Stop condition on SDAx and SCLx pins. Hardware is clear at end of master Stop sequence.
0= Stop condition is not in progress
RSEN: Repeated Start Condition Enable bit (when operating as I2C master)
1= Initiates Repeated Start condition on SDAx and SCLx pins. Hardware is clear at end of master
Repeated Start sequence.
0= Repeated Start condition is not in progress
bit 0
SEN: Start Condition Enable bit (when operating as I2C master)
1 = Initiates Start condition on SDAx and SCLx pins. Hardware is clear at end of master Start
sequence.
0= Start condition is not in progress
2008-2014 Microchip Technology Inc.
DS70000318G-page 229
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 17-2: I2CxSTAT: I2Cx STATUS REGISTER
R-0, HSC
ACKSTAT
bit 15
R-0, HSC
TRSTAT
U-0
—
U-0
—
U-0
—
R/C-0, HSC
BCL
R-0, HSC
GCSTAT
R-0, HSC
ADD10
bit 8
R/C-0, HS R/C-0, HS R-0, HSC R/C-0, HSC R/C-0, HSC
R-0, HSC
R_W
R-0, HSC
RBF
R-0, HSC
TBF
IWCOL
bit 7
I2COV
D_A
P
S
bit 0
Legend:
C = Clearable bit
W = Writable bit
‘1’ = Bit is set
HSC = Hardware Settable/Clearable bit
U = Unimplemented bit, read as ‘0’
R = Readable bit
-n = Value at POR
‘0’ = Bit is cleared
x = Bit is unknown
HS = Hardware Settable bit
bit 15
bit 14
ACKSTAT: Acknowledge Status bit
(when operating as I2C™ master, applicable to master transmit operation)
1= NACK received from slave
0= ACK received from slave
Hardware is set or clear at end of slave Acknowledge.
TRSTAT: Transmit Status bit (when operating as I2C master, applicable to master transmit operation)
1= Master transmit is in progress (8 bits + ACK)
0= Master transmit is not in progress
Hardware is set at beginning of master transmission. Hardware is clear at end of slave Acknowledge.
bit 13-11
bit 10
Unimplemented: Read as ‘0’
BCL: Master Bus Collision Detect bit
1= A bus collision has been detected during a master operation
0= No collision
Hardware is set at detection of bus collision.
bit 9
bit 8
bit 7
bit 6
bit 5
GCSTAT: General Call Status bit
1= General call address was received
0= General call address was not received
Hardware is set when address matches general call address. Hardware is clear at Stop detection.
ADD10: 10-Bit Address Status bit
1= 10-bit address was matched
0= 10-bit address was not matched
Hardware is set at match of 2nd byte of matched 10-bit address. Hardware is clear at Stop detection.
IWCOL: I2Cx Write Collision Detect bit
1= An attempt to write to the I2CxTRN register failed because the I2C module is busy
0= No collision
Hardware is set at occurrence of write to I2CxTRN while busy (cleared by software).
I2COV: I2Cx Receive Overflow Flag bit
1= A byte was received while the I2CxRCV register is still holding the previous byte
0= No overflow
Hardware is set at attempt to transfer I2CxRSR to I2CxRCV (cleared by software).
D_A: Data/Address bit (when operating as I2C slave)
1= Indicates that the last byte received was data
0= Indicates that the last byte received was a device address
Hardware is clear at device address match. Hardware is set by reception of slave byte.
DS70000318G-page 230
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 17-2: I2CxSTAT: I2Cx STATUS REGISTER (CONTINUED)
bit 4
bit 3
bit 2
bit 1
P: Stop bit
1= Indicates that a Stop bit has been detected last
0= Stop bit was not detected last
Hardware is set or clear when Start, Repeated Start or Stop is detected.
S: Start bit
1= Indicates that a Start (or Repeated Start) bit has been detected last
0= Start bit was not detected last
Hardware is set or clear when Start, Repeated Start or Stop is detected.
R_W: Read/Write Information bit (when operating as I2C slave)
1= Read – indicates data transfer is output from slave
0= Write – indicates data transfer is input to slave
Hardware is set or clear after reception of an I2C device address byte.
RBF: Receive Buffer Full Status bit
1= Receive is complete, I2CxRCV is full
0= Receive is not complete, I2CxRCV is empty
Hardware is set when I2CxRCV is written with a received byte. Hardware is clear when software reads
I2CxRCV.
bit 0
TBF: Transmit Buffer Full Status bit
1= Transmit is in progress, I2CxTRN is full
0= Transmit is complete, I2CxTRN is empty
Hardware is set when software writes to I2CxTRN. Hardware is clear at completion of data transmission.
2008-2014 Microchip Technology Inc.
DS70000318G-page 231
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 17-3: I2CxMSK: I2Cx SLAVE MODE ADDRESS MASK REGISTER
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
AMSK<9:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
AMSK<7:0>
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-10
bit 9-0
Unimplemented: Read as ‘0’
AMSK<9:0>: Mask for Address bit x Select bits
1= Enables masking for bit x of incoming message address; bit match is not required in this position
0= Disables masking for bit x; bit match is required in this position
DS70000318G-page 232
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The primary features of the UART module are:
18.0 UNIVERSAL ASYNCHRONOUS
• Full-Duplex, 8-Bit or 9-Bit Data Transmission
through the UxTX and UxRX Pins
RECEIVER TRANSMITTER
(UART)
• Even, Odd or No Parity Options (for 8-bit data)
Note 1: This data sheet summarizes the features
• One or Two Stop bits
of the dsPIC33FJ06GS101/X02 and
• Hardware Flow Control Option with UxCTS and
UxRTS Pins
dsPIC33FJ16GSX02/X04
family
of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to “UART” (DS70188) in the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available on the
Microchip web site (www.microchip.com).
• Fully Integrated Baud Rate Generator with 16-Bit
Prescaler
• Baud Rates Ranging from 12.5 Mbps to 38 bps at
50 MIPS
• 4-Deep First-In First-Out (FIFO) Transmit Data
Buffer
• 4-Deep FIFO Receive Data Buffer
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
• Parity, Framing and Buffer Overrun Error Detection
• Support for 9-Bit mode with Address Detect
(9th bit = 1)
• Transmit and Receive Interrupts
• A Separate Interrupt for all UART Error Conditions
• Loopback mode for Diagnostic Support
• Support for Sync and Break Characters
• Support for Automatic Baud Rate Detection
• IrDA Encoder and Decoder Logic
The Universal Asynchronous Receiver Transmitter
(UART) module is one of the serial I/O modules
available in the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 device families. The UART
is a full-duplex, asynchronous system that can commu-
nicate with peripheral devices, such as personal
computers, LIN/J2602, RS-232 and RS-485 interfaces.
The module also supports a hardware flow control
option with the UxCTS and UxRTS pins and also
includes an IrDA® encoder and decoder.
• 16x Baud Clock Output for IrDA® Support
A simplified block diagram of the UART module is
shown in Figure 1. The UART module consists of these
key hardware elements:
• Baud Rate Generator
• Asynchronous Transmitter
• Asynchronous Receiver
FIGURE 1:
UART1 SIMPLIFIED BLOCK DIAGRAM
Baud Rate Generator
IrDA®
Hardware Flow Control
UART Receiver
U1RTS/BCLK1
U1CTS
U1RX
U1TX
UART Transmitter
2008-2014 Microchip Technology Inc.
DS70000318G-page 233
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 18-1: UxMODE: UARTx MODE REGISTER
R/W-0
UARTEN(1)
U-0
—
R/W-0
USIDL
R/W-0
IREN(2)
R/W-0
U-0
—
R/W-0
UEN1
R/W-0
UEN0
RTSMD
bit 15
bit 8
R/W-0, HC
WAKE
R/W-0
R/W-0, HC
ABAUD
R/W-0
R/W-0
BRGH
R/W-0
R/W-0
R/W-0
LPBACK
URXINV
PDSEL1
PDSEL0
STSEL
bit 7
bit 0
Legend:
HC = Hardware Clearable bit
W = Writable bit
R = Readable bit
-n = Value at POR
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
‘1’ = Bit is set
bit 15
UARTEN: UARTx Enable bit(1)
1= UARTx is enabled; all UARTx pins are controlled by UARTx as defined by UEN<1:0>
0= UARTx is disabled; all UARTx pins are controlled by port latches, UARTx power consumption
is minimal
bit 14
bit 13
Unimplemented: Read as ‘0’
USIDL: UARTx Stop in Idle Mode bit
1= Discontinues module operation when device enters Idle mode
0= Continues module operation in Idle mode
bit 12
bit 11
IREN: IrDA® Encoder and Decoder Enable bit(2)
1= IrDA encoder and decoder are enabled
0= IrDA encoder and decoder are disabled
RTSMD: Mode Selection for UxRTS Pin bit
1= UxRTS pin is in Simplex mode
0= UxRTS pin is in Flow Control mode
bit 10
Unimplemented: Read as ‘0’
UEN<1:0>: UARTx Enable bits
bit 9-8
11= UxTX, UxRX and BCLK pins are enabled and used; UxCTS pin is controlled by port latches
10= UxTX, UxRX, UxCTS and UxRTS pins are enabled and used
01= UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin is controlled by port latches
00= UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/BCLK pins are controlled by
port latches
bit 7
WAKE: Wake-up on Start bit Detect During Sleep Mode Enable bit
1= UARTx will continue to sample the UxRX pin; interrupt is generated on falling edge, bit is cleared
in hardware on the following rising edge
0= No wake-up is enabled
bit 6
bit 5
LPBACK: UARTx Loopback Mode Select bit
1= Enables Loopback mode
0= Loopback mode is disabled
ABAUD: Auto-Baud Enable bit
1= Enable baud rate measurement on the next character – requires reception of a Sync field (55h)
before other data; cleared in hardware upon completion
0= Baud rate measurement is disabled or has completed
Note 1: Refer to “UART” (DS70188) in the “dsPIC33F/PIC24H Family Reference Manual” for information on
enabling the UART module for receive or transmit operation.
2: This feature is only available for the 16x BRG mode (BRGH = 0).
DS70000318G-page 234
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 18-1: UxMODE: UARTx MODE REGISTER (CONTINUED)
bit 4
URXINV: UARTx Receive Polarity Inversion bit
1= UxRX Idle state is ‘0’
0= UxRX Idle state is ‘1’
bit 3
BRGH: High Baud Rate Enable bit
1= BRG generates 4 clocks per bit period (4x baud clock, High-Speed mode)
0= BRG generates 16 clocks per bit period (16x baud clock, Standard mode)
bit 2-1
PDSEL<1:0>: Parity and Data Selection bits
11= 9-bit data, no parity
10= 8-bit data, odd parity
01= 8-bit data, even parity
00= 8-bit data, no parity
bit 0
STSEL: Stop Bit Selection bit
1= Two Stop bits
0= One Stop bit
Note 1: Refer to “UART” (DS70188) in the “dsPIC33F/PIC24H Family Reference Manual” for information on
enabling the UART module for receive or transmit operation.
2: This feature is only available for the 16x BRG mode (BRGH = 0).
2008-2014 Microchip Technology Inc.
DS70000318G-page 235
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 18-2: UxSTA: UARTx STATUS AND CONTROL REGISTER
R/W-0
R/W-0
R/W-0
U-0
—
R/W-0, HC
UTXBRK
R/W-0
UTXEN(1)
R-0
R-1
UTXISEL1
UTXINV
UTXISEL0
UTXBF
TRMT
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R-1
R-0
R-0
R/C-0
R-0
URXISEL1
URXISEL0
ADDEN
RIDLE
PERR
FERR
OERR
URXDA
bit 7
bit 0
Legend:
HC = Hardware Clearable bit
W = Writable bit
C = Clearable bit
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
R = Readable bit
-n = Value at POR
‘1’ = Bit is set
bit 15,13
UTXISEL<1:0>: UARTx Transmission Interrupt Mode Selection bits
11= Reserved; do not use
10= Interrupt when a character is transferred to the Transmit Shift Register (TSR), and as a result,
the transmit buffer becomes empty
01= Interrupt when the last character is shifted out of the Transmit Shift Register; all transmit
operations are completed
00= Interrupt when a character is transferred to the Transmit Shift Register (this implies there is at
least one character open in the transmit buffer)
bit 14
UTXINV: UARTx Transmit Polarity Inversion bit
If IREN = 0:
1= UxTX Idle state is ‘0’
0= UxTX Idle state is ‘1’
If IREN = 1:
1= IrDA® encoded UxTX Idle state is ‘1’
0= IrDA encoded UxTX Idle state is ‘0’
bit 12
bit 11
Unimplemented: Read as ‘0’
UTXBRK: UARTx Transmit Break bit
1= Sends Sync Break on next transmission – Start bit, followed by twelve ‘0’ bits, followed by Stop
bit; cleared by hardware upon completion
0= Sync Break transmission is disabled or has completed
bit 10
UTXEN: UARTx Transmit Enable bit(1)
1= Transmit is enabled, UxTX pin is controlled by UARTx
0= Transmit is disabled, any pending transmission is aborted and buffer is reset; UxTX pin is
controlled by port
bit 9
UTXBF: UARTx Transmit Buffer Full Status bit (read-only)
1= Transmit buffer is full
0= Transmit buffer is not full; at least one more character can be written
bit 8
TRMT: Transmit Shift Register Empty bit (read-only)
1= Transmit Shift Register is empty and transmit buffer is empty (the last transmission has completed)
0= Transmit Shift Register is not empty, a transmission is in progress or queued
bit 7-6
URXISEL<1:0>: UARTx Receive Interrupt Mode Selection bits
11= Interrupt is set on UxRSR transfer, making the receive buffer full (i.e., has 4 data characters)
10= Interrupt is set on UxRSR transfer, making the receive buffer 3/4 full (i.e., has 3 data characters)
0x= Interrupt is set when any character is received and transferred from the UxRSR to the receive
buffer; receive buffer has one or more characters
Note 1: Refer to “UART” (DS70188) in the “dsPIC33F/PIC24H Family Reference Manual” for information on
enabling the UART module for transmit operation.
DS70000318G-page 236
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 18-2: UxSTA: UARTx STATUS AND CONTROL REGISTER (CONTINUED)
bit 5
bit 4
bit 3
bit 2
ADDEN: Address Character Detect bit (bit 8 of received data = 1)
1= Address Detect mode is enable; if 9-bit mode is not selected, this does not take effect
0= Address Detect mode is disabled
RIDLE: Receiver Idle bit (read-only)
1= Receiver is Idle
0= Receiver is active
PERR: Parity Error Status bit (read-only)
1= Parity error has been detected for the current character (character at the top of the receive FIFO)
0= Parity error has not been detected
FERR: Framing Error Status bit (read-only)
1= Framing error has been detected for the current character (character at the top of the receive
FIFO)
0= Framing error has not been detected
bit 1
bit 0
OERR: Receive Buffer Overrun Error Status bit (clear/read-only)
1= Receive buffer has overflowed
0= Receive buffer has not overflowed; clearing a previously set OERR bit (1 0transition) will reset
the receiver buffer and the UxRSR to the empty state
URXDA: UARTx Receive Buffer Data Available bit (read-only)
1= Receive buffer has data, at least one more character can be read
0= Receive buffer is empty
Note 1: Refer to “UART” (DS70188) in the “dsPIC33F/PIC24H Family Reference Manual” for information on
enabling the UART module for transmit operation.
2008-2014 Microchip Technology Inc.
DS70000318G-page 237
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 238
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
This ADC works with the high-speed PWM module in
power control applications that require high-frequency
control loops. This module can sample and convert two
analog inputs in a 0.5 microsecond when two SARs are
19.0 HIGH-SPEED 10-BIT
ANALOG-TO-DIGITAL
CONVERTER (ADC)
used. This small conversion delay reduces the “phase
Note 1: This data sheet summarizes the features
lag” between measurement and control system
of the dsPIC33FJ06GS101/X02 and
response.
dsPIC33FJ16GSX02/X04 families of
Up to five inputs may be sampled at a time (four inputs
from the dedicated Sample-and-Hold circuits and one
from the shared Sample-and-Hold circuit). If multiple
inputs request conversion, the ADC will convert them in
a sequential manner, starting with the lowest order
input.
devices. It is not intended to be a compre-
hensive reference source. To complement
the information in this data sheet, refer to
“High-Speed 10-Bit Analog-to-Digital
Converter (ADC)” (DS70000321) in the
“dsPIC33/PIC24 Family Reference Man-
ual”, which is available on the Microchip
web site (www.microchip.com).
This ADC design provides each pair of analog inputs
(AN1, AN0), (AN3, AN2),..., the ability to specify its own
trigger source out of a maximum of sixteen different
trigger sources. This capability allows this ADC to
sample and convert analog inputs that are associated
with PWM generators operating on Independent Time
Bases (ITBs).
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
The user application typically requires synchronization
between analog data sampling and PWM output to the
application circuit. The very high-speed operation of
this ADC module allows “data on demand”.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
devices provide high-speed, successive approximation
Analog-to-Digital conversions to support applications,
such as AC/DC and DC/DC power converters.
In addition, several hardware features have been
added to the peripheral interface to improve real-time
performance in a typical DSP-based application.
19.1 Features Overview
• Result alignment options
• Automated sampling
The ADC module comprises the following features:
• 10-bit resolution
• Unipolar inputs
• External conversion start control
• Two internal inputs to monitor the INTREF internal
reference and the EXTREF input signal
• Up to two Successive Approximation Registers
(SARs)
19.3 Module Functionality
• Up to 12 external input channels
• Up to two internal analog inputs
• Dedicated result register for each analog input
• ±1 LSB accuracy at 3.3V
The high-speed, 10-bit ADC module is designed to
support power conversion applications when used with
the high-speed PWM module. The ADC may have one
or two SAR modules, depending on the device variant.
If two SARs are present on a device, two conversions
can be processed at a time, yielding 4 Msps conversion
rate. If only one SAR is present on a device, only one
conversion can be processed at a time, yielding 2 Msps
conversion rate. The high-speed 10-bit ADC produces
two 10-bit conversion results in a 0.5 microsecond.
• Single supply operation
• 4 Msps conversion rate at 3.3V (devices with
two SARs)
• 2 Msps conversion rate at 3.3V (devices with
one SAR)
• Low-power CMOS technology
The ADC module supports up to 12 external analog
inputs and two internal analog inputs. To monitor
reference voltage, two internal inputs, AN12 and AN13,
are connected to the EXTREF and INTREF voltages,
respectively.
19.2 Module Description
This ADC module is designed for applications that require
low latency between the request for conversion and the
resultant output data. Typical applications include:
The analog reference voltage is defined as the device
supply voltage (AVDD/AVSS).
• AC/DC power supplies
• DC/DC Converters
• Power Factor Correction (PFC)
Block diagrams of the ADC module are shown in
Figure 19-1 through Figure 19-6.
2008-2014 Microchip Technology Inc.
DS70000318G-page 239
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 19-1:
ADC BLOCK DIAGRAM FOR dsPIC33FJ06GS101 DEVICES WITH ONE SAR
Even Numbered Inputs with Dedicated
Sample-and-Hold (S&H) Circuits
AN0
AN2
Six
16-Bit
Registers
SAR
Core
AN1
Shared Sample-and-Hold
AN3
AN6
AN7
DS70000318G-page 240
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 19-2:
ADC BLOCK DIAGRAM FOR dsPIC33FJ06GS102 DEVICES WITH ONE SAR
Even Numbered Inputs with Dedicated
Sample-and-Hold (S&H) Circuits
AN0
AN2
Six
16-Bit
Registers
SAR
Core
AN1
Shared Sample-and-Hold
AN3
AN4
AN5
2008-2014 Microchip Technology Inc.
DS70000318G-page 241
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 19-3:
ADC BLOCK DIAGRAM FOR dsPIC33FJ06GS202 DEVICES WITH ONE SAR
Even Numbered Inputs with Dedicated
Sample-and-Hold (S&H) Circuits
AN0
AN2
Eight
16-Bit
Registers
SAR
Core
AN12(1)
(EXTREF)
AN1
AN3
AN4
Shared Sample-and-Hold
AN5
AN13(2)
(INTREF)
Note 1: AN12 (EXTREF) is an internal analog input. To measure the voltage at AN12 (EXTREF), an analog comparator must be enabled
and EXTREF must be selected as the comparator reference.
2: AN13 (INTREF) is an internal analog input and is not available on a pin.
DS70000318G-page 242
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 19-4:
ADC BLOCK DIAGRAM FOR dsPIC33FJ16GS402/404 DEVICES WITH ONE SAR
Even Numbered Inputs with Dedicated
Sample-and-Hold (S&H) Circuits
AN0
AN2
AN4
Eight
16-bit
Registers
SAR
Core
AN1
AN3
Shared Sample-and-Hold
AN5
AN6
AN7
2008-2014 Microchip Technology Inc.
DS70000318G-page 243
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 19-5:
ADC BLOCK DIAGRAM FOR dsPIC33FJ16GS502 DEVICES WITH TWO SARS
Even Numbered Inputs with Dedicated
Sample-and-Hold (S&H) Circuits
AN0
AN2
AN4
AN6
Five
16-Bit
Registers
SAR
Core
Even Numbered Inputs
with Shared S&H
AN12(1)
(EXTREF)
AN1
AN3
Odd Numbered Inputs
with Shared S&H
Five
16-Bit
Registers
AN5
AN7
SAR
Core
AN13(2)
(INTREF)
Note 1: AN12 (EXTREF) is an internal analog input. To measure the voltage at AN12 (EXTREF), an analog comparator must be enabled
and EXTREF must be selected as the comparator reference.
2: AN13 (INTREF) is an internal analog input and is not available on a pin.
DS70000318G-page 244
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 19-6:
ADC BLOCK DIAGRAM FOR dsPIC33FJ16GS504 DEVICES WITH TWO SARS
Even Numbered Inputs with Dedicated
Sample-and-Hold (S&H) Circuits
AN0
AN2
AN4
AN6
Seven
16-Bit
Registers
SAR
Core
AN8
Even Numbered Inputs
with Shared S&H
AN10
AN12(1)
(EXTREF)
AN1
AN3
Odd Numbered Inputs
with Shared S&H
Seven
16-Bit
Registers
SAR
Core
AN5
AN7
AN9
AN11
AN13(2)
(INTREF)
Note 1: AN12 (EXTREF) is an internal analog input. To measure the voltage at AN12 (EXTREF), an analog comparator must be enabled
and EXTREF must be selected as the comparator reference.
2: AN13 (INTREF) is an internal analog input and is not available on a pin.
2008-2014 Microchip Technology Inc.
DS70000318G-page 245
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The ADCON register controls the operation of the
ADC module. The ADSTAT register displays the
status of the conversion processes. The ADPCFG
registers configure the port pins as analog inputs or
19.4 ADC Control Registers
The ADC module uses the following control and status
registers:
as digital I/O. The ADCPCx registers control the
triggering of the ADC conversions. See Register 19-1
through Register 19-8 for detailed bit configurations.
• ADCON: Analog-to-Digital Control Register
• ADSTAT: Analog-to-Digital Status Register
• ADBASE: Analog-to-Digital Base Register(1,2)
Note:
A unique feature of the ADC module is its
ability to sample inputs in an asynchronous
• ADPCFG: Analog-to-Digital Port Configuration
Register
manner.
Individual
Sample-and-Hold
• ADCPC0: Analog-to-Digital Convert Pair Control
Register 0
circuits can be triggered independently of
each other.
• ADCPC1: Analog-to-Digital Convert Pair Control
Register 1
• ADCPC2: Analog-to-Digital Convert Pair Control
Register 2(1)
• ADCPC3: Analog-to-Digital Convert Pair Control
Register 3(1)
DS70000318G-page 246
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-1: ADCON: ANALOG-TO-DIGITAL CONTROL REGISTER
R/W-0
ADON
U-0
—
R/W-0
R/W-0
SLOWCLK(1)
U-0
—
R/W-0
U-0
—
R/W-0
FORM(1)
ADSIDL
GSWTRG
bit 15
bit 8
R/W-0
EIE(1)
R/W-0
R/W-0
R/W-0
U-0
—
R/W-0
ADCS2(1)
R/W-1
ADCS1(1)
R/W-1
ADCS0(1)
ORDER(1,2) SEQSAMP(1,2) ASYNCSAMP(1)
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
ADON: Analog-to-Digital Operating Mode bit
1= Analog-to-Digital Converter (ADC) module is operating
0= ADC Converter is off
bit 14
bit 13
Unimplemented: Read as ‘0’
ADSIDL: ADC Stop in Idle Mode bit
1= Discontinues module operation when device enters Idle mode
0= Continues module operation in Idle mode
bit 12
SLOWCLK: Enable The Slow Clock Divider bit(1)
1= ADC is clocked by the auxiliary PLL (ACLK)
0= ADC is clock by the primary PLL (FVCO)
bit 11
bit 10
Unimplemented: Read as ‘0’
GSWTRG: Global Software Trigger bit
When this bit is set by the user, it will trigger conversions if selected by the TRGSRC<4:0> bits in the
ADCPCx registers. This bit must be cleared by the user prior to initiating another global trigger (i.e., this
bit is not auto-clearing).
bit 9
bit 8
Unimplemented: Read as ‘0’
FORM: Data Output Format bit(1)
1= Fractional (DOUT = dddd dddd dd00 0000)
0= Integer (DOUT = 0000 00dd dddd dddd)
bit 7
bit 6
bit 5
EIE: Early Interrupt Enable bit(1)
1= Interrupt is generated after first conversion is completed
0= Interrupt is generated after second conversion is completed
ORDER: Conversion Order bit(1,2)
1= Odd numbered analog input is converted first, followed by conversion of even numbered input
0= Even numbered analog input is converted first, followed by conversion of odd numbered input
SEQSAMP: Sequential Sample Enable bit(1,2)
1= Shared Sample-and-Hold (S&H) circuit is sampled at the start of the second conversion if
ORDER = 0. If ORDER = 1, then the shared S&H is sampled at the start of the first conversion.
0= Shared S&H is sampled at the same time the dedicated S&H is sampled if the shared S&H is not
currently busy with an existing conversion process. If the shared S&H is busy at the time the
dedicated S&H is sampled, then the shared S&H will sample at the start of the new conversion cycle.
Note 1: These control bits can only be changed while ADC is disabled (ADON = 0).
2: These bits are only available on devices with one SAR.
2008-2014 Microchip Technology Inc.
DS70000318G-page 247
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-1: ADCON: ANALOG-TO-DIGITAL CONTROL REGISTER (CONTINUED)
bit 4
ASYNCSAMP: Asynchronous Dedicated S&H Sampling Enable bit(1)
1= The dedicated S&H is constantly sampling and then terminates sampling as soon as the trigger
pulse is detected
0= The dedicated S&H starts sampling when the trigger event is detected and completes the sampling
process in two ADC clock cycles
bit 3
Unimplemented: Read as ‘0’
bit 2-0
ADCS<2:0>: Analog-to-Digital Conversion Clock Divider Select bits(1)
111= FADC/8
110= FADC/7
101= FADC/6
100= FADC/5
011= FADC/4 (default)
010= FADC/3
001= FADC/2
000= FADC/1
Note 1: These control bits can only be changed while ADC is disabled (ADON = 0).
2: These bits are only available on devices with one SAR.
DS70000318G-page 248
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-2: ADSTAT: ANALOG-TO-DIGITAL STATUS REGISTER
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
U-0
—
R/C-0, HS
P6RDY
R/C-0, HS
P5RDY
R/C-0, HS
P4RDY
R/C-0, HS
P3RDY
R/C-0, HS
P2RDY
R/C-0, HS
P1RDY
R/C-0, HS
P0RDY
bit 7
bit 0
Legend:
C = Clearable bit
W = Writable bit
‘1’ = Bit is set
HS = Hardware Settable bit
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
R = Readable bit
-n = Value at POR
bit 15-7
bit 6
Unimplemented: Read as ‘0’
P6RDY: Conversion Data for Pair 6 Ready bit
Bit is set when data is ready in buffer, cleared when a ‘0’ is written to this bit.
P5RDY: Conversion Data for Pair 5 Ready bit
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Bit is set when data is ready in buffer, cleared when a ‘0’ is written to this bit.
P4RDY: Conversion Data for Pair 4 Ready bit
Bit is set when data is ready in buffer, cleared when a ‘0’ is written to this bit.
P3RDY: Conversion Data for Pair 3 Ready bit
Bit is set when data is ready in buffer, cleared when a ‘0’ is written to this bit.
P2RDY: Conversion Data for Pair 2 Ready bit
Bit is set when data is ready in buffer, cleared when a ‘0’ is written to this bit.
P1RDY: Conversion Data for Pair 1 Ready bit
Bit is set when data is ready in buffer, cleared when a ‘0’ is written to this bit.
P0RDY: Conversion Data for Pair 0 Ready bit
Bit is set when data is ready in buffer, cleared when a ‘0’ is written to this bit.
2008-2014 Microchip Technology Inc.
DS70000318G-page 249
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-3: ADBASE: ANALOG-TO-DIGITAL BASE REGISTER(1,2)
R/W-0
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
bit 8
ADBASE<15:8>
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
U-0
—
ADBASE<7:1>
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-1
ADBASE<15:1>: Analog-to-Digital Base bits
This register contains the base address of the user’s ADC Interrupt Service Routine jump table. This
register, when read, contains the sum of the ADBASE register contents and the encoded value of the
PxRDY status bits.
The encoder logic provides the bit number of the highest priority PxRDY bits, where P0RDY is the
highest priority and P6RDY is the lowest priority.
bit 0
Unimplemented: Read as ‘0’
Note 1: The encoding results are shifted left two bits, so bits 1-0 of the result are always zero.
2: As an alternative to using the ADBASE register, the ADCP0-6 ADC Pair Conversion Complete interrupts
can be used to invoke A to D conversion completion routines for individual ADC input pairs.
REGISTER 19-4: ADPCFG: ANALOG-TO-DIGITAL PORT CONFIGURATION REGISTER
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
bit 8
R/W-0
PCFG<11:8>(1)
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
PCFG<7:0>(1)
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-12
bit 11-0
Unimplemented: Read as ‘0’
PCFG<11:0>: Analog-to-Digital Port Configuration Control bits(1)
1= Port pin in Digital mode; port read input is enabled, Analog-to-Digital input multiplexer is
connected to AVSS
0= Port pin in Analog mode; port read input is disabled, Analog-to-Digital samples the pin voltage
Note 1: Not all PCFGx bits are available on all devices. See Figure 19-1 through Figure 19-6 for the available
analog pins (PCFGx = ANx, where x = 0-11).
DS70000318G-page 250
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-5: ADCPC0: ANALOG-TO-DIGITAL CONVERT PAIR
CONTROL REGISTER 0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IRQEN1
PEND1
SWTRG1
TRGSRC14 TRGSRC13 TRGSRC12 TRGSRC11 TRGSRC10
bit 8
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IRQEN0
PEND0
SWTRG0
TRGSRC04 TRGSRC03 TRGSRC02 TRGSRC01 TRGSRC00
bit 0
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
bit 14
bit 13
IRQEN1: Interrupt Request Enable 1 bit
1= Enables IRQ generation when requested conversion of Channels AN3 and AN2 is completed
0= IRQ is not generated
PEND1: Pending Conversion Status 1 bit
1= Conversion of Channels AN3 and AN2 is pending; set when selected trigger is asserted
0= Conversion is complete
SWTRG1: Software Trigger 1 bit
1= Starts conversion of AN3 and AN2 (if selected by the TRGSRCx bits)(1)
This bit is automatically cleared by hardware when the PEND1 bit is set.
0= Conversion has not started
Note 1: The trigger source must be set as a global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, then the conversion will be performed when the conversion resources are available.
2008-2014 Microchip Technology Inc.
DS70000318G-page 251
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-5: ADCPC0: ANALOG-TO-DIGITAL CONVERT PAIR
CONTROL REGISTER 0 (CONTINUED)
bit 12-8
TRGSRC1<4:0>: Trigger 1 Source Selection bits
Selects trigger source for conversion of Analog Channels AN3 and AN2.
11111= Timer2 period match
•
•
•
11011= Reserved
11010= PWM Generator 4 current-limit ADC trigger
11001= PWM Generator 3 current-limit ADC trigger
11000= PWM Generator 2 current-limit ADC trigger
10111= PWM Generator 1 current-limit ADC trigger
10110= Reserved
•
•
•
10010= Reserved
10001= PWM Generator 4 secondary trigger is selected
10000= PWM Generator 3 secondary trigger is selected
01111= PWM Generator 2 secondary trigger is selected
01110= PWM Generator 1 secondary trigger is selected
01101= Reserved
01100= Timer1 period match
•
•
•
01000= Reserved
00111= PWM Generator 4 primary trigger is selected
00110= PWM Generator 3 primary trigger is selected
00101= PWM Generator 2 primary trigger is selected
00100= PWM Generator 1 primary trigger is selected
00011= PWM Special Event Trigger is selected
00010= Global software trigger is selected
00001= Individual software trigger is selected
00000= No conversion is enabled
bit 7
bit 6
bit 5
IRQEN0: Interrupt Request Enable 0 bit
1= Enables IRQ generation when requested conversion of Channels AN1 and AN0 is completed
0= IRQ is not generated
PEND0: Pending Conversion Status 0 bit
1= Conversion of Channels AN1 and AN0 is pending; set when selected trigger is asserted
0= Conversion is complete
SWTRG0: Software Trigger 0 bit
1= Starts conversion of AN1 and AN0 (if selected by the TRGSRCx bits)(1)
This bit is automatically cleared by hardware when the PEND0 bit is set.
0= Conversion has not started
Note 1: The trigger source must be set as a global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, then the conversion will be performed when the conversion resources are available.
DS70000318G-page 252
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-5: ADCPC0: ANALOG-TO-DIGITAL CONVERT PAIR
CONTROL REGISTER 0 (CONTINUED)
bit 4-0
TRGSRC0<4:0>: Trigger 0 Source Selection bits
Selects trigger source for conversion of Analog Channels AN1 and AN0.
11111= Timer2 period match
•
•
•
11011= Reserved
11010= PWM Generator 4 current-limit ADC trigger
11001= PWM Generator 3 current-limit ADC trigger
11000= PWM Generator 2 current-limit ADC trigger
10111= PWM Generator 1 current-limit ADC trigger
10110= Reserved
•
•
•
10010= Reserved
10001= PWM Generator 4 secondary trigger is selected
10000= PWM Generator 3 secondary trigger is selected
01111= PWM Generator 2 secondary trigger is selected
01110= PWM Generator 1 secondary trigger is selected
01101= Reserved
01100= Timer1 period match
•
•
•
01000= Reserved
00111= PWM Generator 4 primary trigger is selected
00110= PWM Generator 3 primary trigger is selected
00101= PWM Generator 2 primary trigger is selected
00100= PWM Generator 1 primary trigger is selected
00011= PWM Special Event Trigger is selected
00010= Global software trigger is selected
00001= Individual software trigger is selected
00000= No conversion is enabled
Note 1: The trigger source must be set as a global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, then the conversion will be performed when the conversion resources are available.
2008-2014 Microchip Technology Inc.
DS70000318G-page 253
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-6: ADCPC1: ANALOG-TO-DIGITAL CONVERT PAIR
CONTROL REGISTER 1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IRQEN3(1)
PEND3(1) SWTRG3(1) TRGSRC34(1) TRGSRC33(1) TRGSRC32(1) TRGSRC31(1) TRGSRC30(1)
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IRQEN2(2)
PEND2(2) SWTRG2(2) TRGSRC24(2) TRGSRC23(2) TRGSRC22(2) TRGSRC21(2) TRGSRC20(2)
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
bit 14
bit 13
IRQEN3: Interrupt Request Enable 3 bit(1)
1= Enables IRQ generation when requested conversion of Channels AN7 and AN6 is completed
0= IRQ is not generated
PEND3: Pending Conversion Status 3 bit(1)
1= Conversion of Channels AN7 and AN6 is pending; set when selected trigger is asserted
0= Conversion is complete
SWTRG3: Software Trigger 3 bit(1)
1= Starts conversion of AN7 and AN6 (if selected by the TRGSRCx bits)(3)
This bit is automatically cleared by hardware when the PEND3 bit is set.
0= Conversion has not started
Note 1: These bits are available in the dsPIC33FJ16GS402/404, dsPIC33FJ16GS504, dsPIC33FJ16GS502 and
dsPIC33FJ06GS101 devices only.
2: These bits are available in the dsPIC33FJ16GS502, dsPIC33FJ16GS504, dsPIC33FJ06GS102,
dsPIC33FJ06GS202 and dsPIC33FJ16GS402/404 devices only.
3: The trigger source must be set as a global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, then the conversion will be performed when the conversion resources are available.
DS70000318G-page 254
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-6: ADCPC1: ANALOG-TO-DIGITAL CONVERT PAIR
CONTROL REGISTER 1 (CONTINUED)
bit 12-8
TRGSRC3<4:0>: Trigger 3 Source Selection bits(1)
Selects trigger source for conversion of Analog Channels AN7 and AN6.
11111= Timer2 period match
•
•
•
11011= Reserved
11010= PWM Generator 4 current-limit ADC trigger
11001= PWM Generator 3 current-limit ADC trigger
11000= PWM Generator 2 current-limit ADC trigger
10111= PWM Generator 1 current-limit ADC trigger
10110= Reserved
•
•
•
10010= Reserved
10001= PWM Generator 4 secondary trigger is selected
10000= PWM Generator 3 secondary trigger is selected
01111= PWM Generator 2 secondary trigger is selected
01110= PWM Generator 1 secondary trigger is selected
01101= Reserved
01100= Timer1 period match
•
•
•
01000= Reserved
00111= PWM Generator 4 primary trigger is selected
00110= PWM Generator 3 primary trigger is selected
00101= PWM Generator 2 primary trigger is selected
00100= PWM Generator 1 primary trigger is selected
00011= PWM Special Event Trigger is selected
00010= Global software trigger is selected
00001= Individual software trigger is selected
00000= No conversion is enabled
bit 7
bit 6
bit 5
IRQEN2: Interrupt Request Enable 2 bit((2))
1= Enables IRQ generation when requested conversion of Channels AN5 and AN4 is completed
0= IRQ is not generated
PEND2: Pending Conversion Status 2 bit((2))
1= Conversion of Channels AN5 and AN4 is pending; set when selected trigger is asserted
0= Conversion is complete
SWTRG2: Software Trigger 2 bit((2))
1= Starts conversion of AN5 and AN4 (if selected by the TRGSRCx bits)(3)
This bit is automatically cleared by hardware when the PEND2 bit is set.
0= Conversion has not started
Note 1: These bits are available in the dsPIC33FJ16GS402/404, dsPIC33FJ16GS504, dsPIC33FJ16GS502 and
dsPIC33FJ06GS101 devices only.
2: These bits are available in the dsPIC33FJ16GS502, dsPIC33FJ16GS504, dsPIC33FJ06GS102,
dsPIC33FJ06GS202 and dsPIC33FJ16GS402/404 devices only.
3: The trigger source must be set as a global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, then the conversion will be performed when the conversion resources are available.
2008-2014 Microchip Technology Inc.
DS70000318G-page 255
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-6: ADCPC1: ANALOG-TO-DIGITAL CONVERT PAIR
CONTROL REGISTER 1 (CONTINUED)
bit 4-0
TRGSRC2<4:0>: Trigger 2 Source Selection bits(2)
Selects trigger source for conversion of Analog Channels AN5 and AN4.
11111= Timer2 period match
•
•
•
11011= Reserved
11010= PWM Generator 4 current-limit ADC trigger
11001= PWM Generator 3 current-limit ADC trigger
11000= PWM Generator 2 current-limit ADC trigger
10111= PWM Generator 1 current-limit ADC trigger
10110= Reserved
•
•
•
10010= Reserved
10001= PWM Generator 4 secondary trigger is selected
10000= PWM Generator 3 secondary trigger is selected
01111= PWM Generator 2 secondary trigger is selected
01110= PWM Generator 1 secondary trigger is selected
01101= Reserved
01100= Timer1 period match
•
•
•
01000= Reserved
00111= PWM Generator 4 primary trigger is selected
00110= PWM Generator 3 primary trigger is selected
00101= PWM Generator 2 primary trigger is selected
00100= PWM Generator 1 primary trigger is selected
00011= PWM Special Event Trigger is selected
00010= Global software trigger is selected
00001= Individual software trigger is selected
00000= No conversion is enabled
Note 1: These bits are available in the dsPIC33FJ16GS402/404, dsPIC33FJ16GS504, dsPIC33FJ16GS502 and
dsPIC33FJ06GS101 devices only.
2: These bits are available in the dsPIC33FJ16GS502, dsPIC33FJ16GS504, dsPIC33FJ06GS102,
dsPIC33FJ06GS202 and dsPIC33FJ16GS402/404 devices only.
3: The trigger source must be set as a global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, then the conversion will be performed when the conversion resources are available.
DS70000318G-page 256
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-7: ADCPC2: ANALOG-TO-DIGITAL CONVERT PAIR
CONTROL REGISTER 2(1)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IRQEN5
PEND5
SWTRG5
TRGSRC54 TRGSRC53 TRGSRC52 TRGSRC51 TRGSRC50
bit 8
bit 15
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IRQEN4
PEND4
SWTRG4
TRGSRC44 TRGSRC43 TRGSRC42 TRGSRC41 TRGSRC40
bit 0
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
bit 14
bit 13
IRQEN5: Interrupt Request Enable 5 bit
1= Enables IRQ generation when requested conversion of Channels AN11 and AN10 is completed
0= IRQ is not generated
PEND5: Pending Conversion Status 5 bit
1= Conversion of Channels AN11 and AN10 is pending; set when selected trigger is asserted
0= Conversion is complete
SWTRG5: Software Trigger 5 bit
1= Starts conversion of AN11 and AN10 (if selected by the TRGSRCx bits)(2)
This bit is automatically cleared by hardware when the PEND5 bit is set.
0= Conversion has not started
Note 1: This register is only implemented in the dsPIC33FJ16GS504 devices.
2: The trigger source must be set as a global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, then the conversion will be performed when the conversion resources are available.
2008-2014 Microchip Technology Inc.
DS70000318G-page 257
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-7: ADCPC2: ANALOG-TO-DIGITAL CONVERT PAIR
CONTROL REGISTER 2(1) (CONTINUED)
bit 12-8
TRGSRC5<4:0>: Trigger 5 Source Selection bits
Selects trigger source for conversion of Analog Channels AN11 and AN10.
11111= Timer2 period match
•
•
•
11011= Reserved
11010= PWM Generator 4 current-limit ADC trigger
11001= PWM Generator 3 current-limit ADC trigger
11000= PWM Generator 2 current-limit ADC trigger
10111= PWM Generator 1 current-limit ADC trigger
10110= Reserved
•
•
•
10010= Reserved
10001= PWM Generator 4 secondary trigger is selected
10000= PWM Generator 3 secondary trigger is selected
01111= PWM Generator 2 secondary trigger is selected
01110= PWM Generator 1 secondary trigger is selected
01101= Reserved
01100= Timer1 period match
•
•
•
01000= Reserved
00111= PWM Generator 4 primary trigger is selected
00110= PWM Generator 3 primary trigger is selected
00101= PWM Generator 2 primary trigger is selected
00100= PWM Generator 1 primary trigger is selected
00011= PWM Special Event Trigger is selected
00010= Global software trigger is selected
00001= Individual software trigger is selected
00000= No conversion is enabled
bit 7
bit 6
bit 5
IRQEN4: Interrupt Request Enable 4 bit
1= Enables IRQ generation when requested conversion of Channels AN9 and AN8 is completed
0= IRQ is not generated
PEND4: Pending Conversion Status 4 bit
1= Conversion of Channels AN9 and AN8 is pending; set when selected trigger is asserted
0= Conversion is complete
SWTRG4: Software Trigger 4 bit
1= Starts conversion of AN9 and AN8 (if selected by the TRGSRCx bits)(2)
This bit is automatically cleared by hardware when the PEND4 bit is set.
0= Conversion has not started
Note 1: This register is only implemented in the dsPIC33FJ16GS504 devices.
2: The trigger source must be set as a global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, then the conversion will be performed when the conversion resources are available.
DS70000318G-page 258
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-7: ADCPC2: ANALOG-TO-DIGITAL CONVERT PAIR
CONTROL REGISTER 2(1) (CONTINUED)
bit 4-0
TRGSRC4<4:0>: Trigger 4 Source Selection bits
Selects trigger source for conversion of Analog Channels AN9 and AN8.
11111= Timer2 period match
•
•
•
11011= Reserved
11010= PWM Generator 4 current-limit ADC trigger
11001= PWM Generator 3 current-limit ADC trigger
11000= PWM Generator 2 current-limit ADC trigger
10111= PWM Generator 1 current-limit ADC trigger
10110= Reserved
•
•
•
10010= Reserved
10001= PWM Generator 4 secondary trigger is selected
10000= PWM Generator 3 secondary trigger is selected
01111= PWM Generator 2 secondary trigger is selected
01110= PWM Generator 1 secondary trigger is selected
01101= Reserved
01100= Timer1 period match
•
•
•
01000= Reserved
00111= PWM Generator 4 primary trigger is selected
00110= PWM Generator 3 primary trigger is selected
00101= PWM Generator 2 primary trigger is selected
00100= PWM Generator 1 primary trigger is selected
00011= PWM Special Event Trigger is selected
00010= Global software trigger is selected
00001= Individual software trigger is selected
00000= No conversion is enabled
Note 1: This register is only implemented in the dsPIC33FJ16GS504 devices.
2: The trigger source must be set as a global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, then the conversion will be performed when the conversion resources are available.
2008-2014 Microchip Technology Inc.
DS70000318G-page 259
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-8: ADCPC3: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 3(1)
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
IRQEN6
PEND6
SWTRG6
TRGSRC6<4:0>
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-8
bit 7
Unimplemented: Read as ‘0’
IRQEN6: Interrupt Request Enable 6 bit
1= Enables IRQ generation when requested conversion of Channels AN13 and AN12 is completed
0= IRQ is not generated
bit 6
bit 5
PEND6: Pending Conversion Status 6 bit
1= Conversion of Channels AN13 and AN 12 is pending; set when selected trigger is asserted
0= Conversion is complete
SWTRG6: Software Trigger 6 bit
1= Starts conversion of AN13 (INTREF) and AN12 (EXTREF) (if selected by the TRGSRCx bits)(2)
This bit is automatically cleared by hardware when the PEND6 bit is set.
0= Conversion has not started
Note 1: This register is only implemented on the dsPIC33FJ16GS502 and dsPIC33FJ16GS504 devices.
2: The trigger source must be set as global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, conversion will be performed when the conversion resources are available.
DS70000318G-page 260
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 19-8: ADCPC3: ANALOG-TO-DIGITAL CONVERT PAIR CONTROL REGISTER 3(1)
bit 4-0
TRGSRC6<4:0>: Trigger 6 Source Selection bits
Selects trigger source for conversion of Analog Channels AN13 and AN12.
11111= Timer2 period match
•
•
•
11011= Reserved
11010= PWM Generator 4 current-limit ADC trigger
11001= PWM Generator 3 current-limit ADC trigger
11000= PWM Generator 2 current-limit ADC trigger
10111= PWM Generator 1 current-limit ADC trigger
10110= Reserved
•
•
•
10010= Reserved
10001= PWM Generator 4 secondary trigger is selected
10000= PWM Generator 3 secondary trigger is selected
01111= PWM Generator 2 secondary trigger is selected
01110= PWM Generator 1 secondary trigger is selected
01101= Reserved
01100= Timer1 period match
•
•
•
01000= Reserved
00111= PWM Generator 4 primary trigger is selected
00110= PWM Generator 3 primary trigger is selected
00101= PWM Generator 2 primary trigger is selected
00100= PWM Generator 1 primary trigger is selected
00011= PWM Special Event Trigger is selected
00010= Global software trigger is selected
00001= Individual software trigger is selected
00000= No conversion is enabled
Note 1: This register is only implemented on the dsPIC33FJ16GS502 and dsPIC33FJ16GS504 devices.
2: The trigger source must be set as global software trigger prior to setting this bit to ‘1’. If other conversions
are in progress, conversion will be performed when the conversion resources are available.
2008-2014 Microchip Technology Inc.
DS70000318G-page 261
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 262
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
• Programmable output polarity
20.0 HIGH-SPEED ANALOG
• Interrupt generation capability
COMPARATOR
• DACOUT pin to provide DAC output
Note 1: This data sheet summarizes the
• DAC has three ranges of operation:
features of the dsPIC33FJ06GS101/X02
and dsPIC33FJ16GSX02/X04 families of
devices. It is not intended to be a
- AVDD/2
- Internal Reference (INTREF)
- External Reference (EXTREF)
• ADC sample and convert trigger capability
• Disable capability reduces power consumption
• Functional support for PWM module:
- PWM duty cycle control
comprehensive reference source. To
complement the information in this data
sheet, refer to “High-Speed Analog
Comparator”
(DS70296)
in
the
“dsPIC33F/PIC24H Family Reference
Manual”, which is available on the
Microchip web site (www.microchip.com).
- PWM period control
- PWM Fault detect
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
20.2 Module Description
Figure 20-1 shows a functional block diagram of one
analog comparator from the SMPS comparator
module. The analog comparator provides high-speed
operation with a typical delay of 20 ns. The comparator
has a typical offset voltage of ±5 mV. The negative
input of the comparator is always connected to the
DAC circuit. The positive input of the comparator is
connected to an analog multiplexer that selects the
desired source pin.
The dsPIC33F SMPS comparator module monitors
current and/or voltage transients that may be too fast
for the CPU and ADC to capture.
20.1 Features Overview
The SMPS comparator module contains the following
major features:
The analog comparator input pins are typically shared
with pins used by the Analog-to-Digital Converter (ADC)
module. Both the comparator and the ADC can use the
same pins at the same time. This capability enables a
user to measure an input voltage with the ADC and
detect voltage transients with the comparator.
• 16 selectable comparator inputs
• Up to four analog comparators
• 10-bit DAC for each analog comparator
FIGURE 20-1:
HIGH-SPEED ANALOG COMPARATOR MODULE BLOCK DIAGRAM
(1)
INSEL<1:0>
ACMPx (Trigger to PWM)
Status
CMPxA(1)
CMPxB(1)
M
U
X
CMPxC(1)
CMPxD(1)
CMPx(1)
0
1
Pulse
Glitch Filter
Generator
RANGE
CMPPOL
AVDD/2
INTREF(2)
M
U
X
Interrupt Request
DACOUT
DAC
10
CMREF
AVSS
DACOE
(2)
EXTREF
Note 1: x = 1, 2, 3 and 4.
2: For the INTREF and EXTREF values, refer to the DAC Module Specifications (Table 24-43) in Section 24.0
“Electrical Characteristics”.
2008-2014 Microchip Technology Inc.
DS70000318G-page 263
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
20.3 Module Applications
20.5 Interaction with I/O Buffers
This module provides a means for the SMPS dsPIC®
DSC devices to monitor voltage and currents in a
power conversion application. The ability to detect
transient conditions and stimulate the dsPIC DSC
processor and/or peripherals, without requiring the
processor and ADC to constantly monitor voltages or
currents, frees the dsPIC DSC to perform other tasks.
If the comparator module is enabled and a pin has
been selected as the source for the comparator, then
the chosen I/O pad must disable the digital input buffer
associated with the pad to prevent excessive currents
in the digital buffer due to analog input voltages.
20.6 Digital Logic
The comparator module has a high-speed comparator
and an associated 10-bit DAC that provides a
programmable reference voltage to the inverting input
of the comparator. The polarity of the comparator out-
put is user-programmable. The output of the module
can be used in the following modes:
The CMPCONx register (see Register 20-1) provides
the control logic that configures the comparator
module. The digital logic provides a glitch filter for the
comparator output to mask transient signals in less
than two instruction cycles. In Sleep or Idle mode, the
glitch filter is bypassed to enable an asynchronous
path from the comparator to the interrupt controller.
This asynchronous path can be used to wake-up the
processor from Sleep or Idle mode.
• Generate an Interrupt
• Trigger an ADC Sample and Convert Process
• Truncate the PWM Signal (current limit)
• Truncate the PWM Period (current minimum)
• Disable the PWM Outputs (Fault latch)
The comparator can be disabled while in Idle mode if
the CMPSIDL bit is set. If a device has multiple
comparators, if any CMPSIDL bit is set, then the entire
group of comparators will be disabled while in Idle
mode. This behavior reduces complexity in the design
of the clock control logic for this module.
The output of the comparator module may be used in
multiple modes at the same time, such as: 1) generate
an interrupt, 2) have the ADC take a sample and con-
vert it, and 3) truncate the PWM output in response to
a voltage being detected beyond its expected value.
The digital logic also provides a one TCY width pulse
generator for triggering the ADC and generating
interrupt requests.
The comparator module can also be used to wake-up
the system from Sleep or Idle mode when the analog
input voltage exceeds the programmed threshold
voltage.
The CMPDACx (see Register 20-2) register provides
the digital input value to the reference DAC.
If the module is disabled, the DAC and comparator are
disabled to reduce power consumption.
20.4 DAC
The range of the DAC is controlled through an analog
multiplexer that selects either AVDD/2, an internal ref-
erence source, INTREF, or an external reference
source, EXTREF. The full range of the DAC (AVDD/2)
will typically be used when the chosen input source pin
is shared with the ADC. The reduced range option
(INTREF) will likely be used when monitoring current
levels using a current sense resistor. Usually, the
measured voltages in such applications are small
(<1.25V); therefore the option of using a reduced ref-
erence range for the comparator extends the available
DAC resolution in these applications. The use of an
external reference enables the user to connect to a
reference that better suits their application.
20.7 Comparator Input Range
The comparator has
a
limitation for the input
Common-Mode Range (CMR) of (AVDD – 1.5V), typical.
This means that both inputs should not exceed this
range. As long as one of the inputs is within the
Common-Mode Range, the comparator output will be
correct. However, any input exceeding the CMR
limitation will cause the comparator input to be saturated.
If both inputs exceed the CMR, the comparator output
will be indeterminate.
20.8 DAC Output Range
The DAC has a limitation for the maximum reference
voltage input of (AVDD – 1.6) volts. An external
reference voltage input should not exceed this value or
the reference DAC output will become indeterminate.
DACOUT, shown in Figure 20-1, can only be
associated with a single comparator at a given time.
Note:
It should be ensured in software that
multiple DACOE bits are not set. The
output on the DACOUT pin will be indeter-
minate if multiple comparators enable the
DAC output.
20.9 Comparator Registers
The comparator module is controlled by the following
registers:
• CMPCONx: Comparator Control x Register
• CMPDACx: Comparator DAC x Control Register
DS70000318G-page 264
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 20-1: CMPCONx: COMPARATOR CONTROL x REGISTER
R/W-0
U-0
—
R/W-0
r-0
r
r-0
r
r-0
r
r-0
r
R/W-0
CMPON
CMPSIDL
DACOE
bit 15
bit 8
R/W-0
R/W-0
R/W-0
r-0
r
R/W-0
r-0
r
R/W-0
R/W-0
INSEL1
INSEL0
EXTREF
CMPSTAT
CMPPOL
RANGE
bit 7
bit 0
Legend:
r = Reserved bit
W = Writable bit
‘1’ = Bit is set
R = Readable bit
-n = Value at POR
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15
CMPON: Comparator Operating Mode bit
1= Comparator module is enabled
0= Comparator module is disabled (reduces power consumption)
bit 14
bit 13
Unimplemented: Read as ‘0’
CMPSIDL: Comparator Stop in Idle Mode bit
1= Discontinues module operation when device enters Idle mode.
0= Continues module operation in Idle mode
If a device has multiple comparators, any CMPSIDL bit set to ‘1’ disables ALL comparators while in
Idle mode.
bit 12-9
bit 8
Reserved: Read as ‘0’
DACOE: DAC Output Enable
1= DAC analog voltage is output to the DACOUT pin(1)
0= DAC analog voltage is not connected to the DACOUT pin
bit 7-6
bit 5
INSEL<1:0>: Input Source Select for Comparator bits
00= Selects CMPxA input pin
01= Selects CMPxB input pin
10= Selects CMPxC input pin
11= Selects CMPxD input pin
EXTREF: Enable External Reference bit
1= External source provides reference to the DAC (maximum DAC voltage determined by the
external voltage source)
0= Internal reference sources provide reference to the DAC (maximum DAC voltage determined by
the RANGE bit setting)
bit 4
bit 3
bit 2
bit 1
Reserved: Read as ‘0’
CMPSTAT: Current State of Comparator Output Including CMPPOL Selection bit
Reserved: Read as ‘0’
CMPPOL: Comparator Output Polarity Control bit
1= Output is inverted
0= Output is non-inverted
bit 0
RANGE: Selects DAC Output Voltage Range bit
1= High Range: Max DAC Value = AVDD/2, 1.65V at 3.3V AVDD
0= Low Range: Max DAC Value = INTREF(2)
Note 1: DACOUT can be associated only with a single comparator at any given time. The software must ensure
that multiple comparators do not enable the DAC output by setting their respective DACOE bit.
2: Refer to the DAC Module Specifications (Table 24-43) in Section 24.0 “Electrical Characteristics” for
the INTREF value.
2008-2014 Microchip Technology Inc.
DS70000318G-page 265
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
REGISTER 20-2: CMPDACx: COMPARATOR DAC x CONTROL REGISTER
r-0
r
r-0
r
r-0
r
r-0
r
r-0
r
r-0
r
R/W-0
R/W-0
CMREF<9:8>
bit 15
bit 8
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CMREF<7:0>
bit 7
bit 0
Legend:
r = Reserved bit
W = Writable bit
‘1’ = Bit is set
R = Readable bit
-n = Value at POR
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 15-10
bit 9-0
Reserved: Read as ‘0’
CMREF<9:0>: Comparator Reference Voltage Select bits
1111111111= (CMREF<9:0> * INTREF/1024) or (CMREF<9:0> * (AVDD/2)/1024) volts depending
on the RANGE bit or (CMREF<9:0> * EXTREF/1024) if EXTREF is set
•
•
•
0000000000= 0.0 volts
DS70000318G-page 266
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
21.1 Configuration Bits
21.0 SPECIAL FEATURES
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
devices provide nonvolatile memory implementations
for device Configuration bits. Refer to “Device Config-
uration” (DS70194) in the “dsPIC33F/PIC24H Family
Reference Manual” for more information on this
implementation.
Note 1: This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 devices. It is
not intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to the
“dsPIC33F/PIC24H Family Reference
Manual”. Please see the Microchip web
site (www.microchip.com) for the latest
“dsPIC33F/PIC24H Family Reference
Manual” sections.
The Configuration bits can be programmed (read
as ‘0’), or left unprogrammed (read as ‘1’), to select
various device configurations. These bits are mapped
starting at program memory location 0xF80000.
The individual Configuration bit descriptions for the
Configuration registers are shown in Table 21-2.
2: Some registers and associated bits
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization” in
this data sheet for device-specific register
and bit information.
Note that address, 0xF80000, is beyond the user pro-
gram memory space. It belongs to the configuration
memory space (0x800000-0xFFFFFF), which can only
be accessed using Table Reads and Table Writes.
The device Configuration register map is shown in
Table 21-1.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
devices include several features intended to maximize
application flexibility and reliability, and minimize cost
through elimination of external components. These are:
• Flexible Configuration
• Watchdog Timer (WDT)
• Code Protection and CodeGuard™ Security
• JTAG Boundary Scan Interface
• In-Circuit Serial Programming™ (ICSP™)
• In-Circuit Emulation
• Brown-out Reset (BOR)
TABLE 21-1: DEVICE CONFIGURATION REGISTER MAP
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0xF80000 FBS
—
—
—
—
—
—
—
—
—
—
—
—
—
—
BSS2
—
BSS1
—
BSS0
—
BWRP
—
0xF80002 Reserved
0xF80004 FGS
—
GSS1
FNOSC2
GSS0
FNOSC1
GWRP
FNOSC0
POSCMD0
0xF80006 FOSCSEL IESO
—
0xF80008 FOSC
0xF8000A FWDT
0xF8000C FPOR
0xF8000E FICD
0xF80010 FUID0
0xF80012 FUID1
FCKSM1 FCKSM0 IOL1WAY
—
—
OSCIOFNC POSCMD1
FWDTEN WINDIS
—
—
WDTPRE WDTPOST3 WDTPOST2 WDTPOST1 WDTPOST0
(2)
—
—
(1)
—
—
Reserved
—
FPWRT2
—
FPWRT1
ICS1
FPWRT0
ICS0
Reserved
JTAGEN
User Unit ID Byte 0
User Unit ID Byte 1
Legend: — = unimplemented bit, read as ‘
Note 1: These bits are reserved for use by development tools and must be programmed to ‘
2: This bit reads the current programmed value.
0’.
1’.
2008-2014 Microchip Technology Inc.
DS70000318G-page 267
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 21-2: dsPIC33F CONFIGURATION BITS DESCRIPTION
Bit Field
BWRP
Register
RTSP Effect
Description
Boot Segment Program Flash Write Protection bit
FBS
Immediate
1= Boot segment can be written
0= Boot segment is write-protected
BSS<2:0>
FBS
Immediate Boot Segment Program Flash Code Protection Size bits
x11= No boot program Flash segment
Boot Space is 256 Instruction Words (except interrupt vectors):
110= Standard security; boot program Flash segment ends at
0x0003FE
010= High security; boot program Flash segment ends at
0x0003FE
Boot Space is 768 Instruction Words (except interrupt vectors):
101= Standard security; boot program Flash segment ends at
0x0007FE
001= High security; boot program Flash segment ends at
0x0007FE
Boot Space is 1792 Instruction Words (except interrupt vectors):
100= Standard security; boot program Flash segment ends at
0x000FFE
000= High security; boot program Flash segment ends at
0x000FFE
GSS<1:0>
FGS
Immediate General Segment Code-Protect bits
11= User program memory is not code-protected
10= Standard security
0x= High security
GWRP
IESO
FGS
Immediate General Segment Write-Protect bit
1= User program memory is not write-protected
0= User program memory is write-protected
FOSCSEL
Immediate Two-speed Oscillator Start-up Enable bit
1= Start-up device with FRC, then automatically switch to the
user-selected oscillator source when ready
0= Start-up device with user-selected oscillator source
FNOSC<2:0>
FOSCSEL If clock switch Initial Oscillator Source Selection bits
is enabled,
RTSP effect
is on any
111= Internal Fast RC (FRC) Oscillator with Postscaler
110= Internal Fast RC (FRC) Oscillator with Divide-by-16
101= LPRC Oscillator
device Reset;
otherwise,
Immediate
100= Reserved
011= Primary (XT, HS, EC) Oscillator with PLL
010= Primary (XT, HS, EC) Oscillator
001= Internal Fast RC (FRC) Oscillator with PLL
000= FRC Oscillator
FCKSM<1:0>
FOSC
Immediate Clock Switching Mode bits
1x= Clock switching is disabled, Fail-Safe Clock Monitor is disabled
01= Clock switching is enabled, Fail-Safe Clock Monitor is disabled
00= Clock switching is enabled, Fail-Safe Clock Monitor is enabled
IOL1WAY
FOSC
FOSC
Immediate Peripheral Pin Select Configuration bit
1= Allows only one reconfiguration
0= Allows multiple reconfigurations
OSCIOFNC
Immediate OSC2 Pin Function bit (except in XT and HS modes)
1= OSC2 is the clock output
0= OSC2 is the general purpose digital I/O pin
DS70000318G-page 268
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 21-2: dsPIC33F CONFIGURATION BITS DESCRIPTION (CONTINUED)
Bit Field
Register
RTSP Effect
Description
Primary Oscillator Mode Select bits
POSCMD<1:0>
FOSC
Immediate
11= Primary Oscillator is disabled
10= HS Crystal Oscillator mode
01= XT Crystal Oscillator mode
00= EC (External Clock) mode
FWDTEN
FWDT
Immediate Watchdog Timer Enable bit
1= Watchdog Timer is always enabled (LPRC oscillator cannot be
disabled; clearing the SWDTEN bit in the RCON register will have
no effect)
0= Watchdog Timer is enabled/disabled by user software (LPRC can
be disabled by clearing the SWDTEN bit in the RCON register)
WINDIS
FWDT
FWDT
FWDT
Immediate Watchdog Timer Window Enable bit
1= Watchdog Timer in Non-Window mode
0= Watchdog Timer in Window mode
WDTPRE
Immediate Watchdog Timer Prescaler bit
1= 1:128
0= 1:32
WDTPOST<3:0>
Immediate Watchdog Timer Postscaler bits
1111= 1:32,768
1110= 1:16,384
•
•
•
0001= 1:2
0000= 1:1
FPWRT<2:0>
FPOR
Immediate Power-on Reset Timer Value Select bits
111= PWRT = 128 ms
110= PWRT = 64 ms
101= PWRT = 32 ms
100= PWRT = 16 ms
011= PWRT = 8 ms
010= PWRT = 4 ms
001= PWRT = 2 ms
000= PWRT = Disabled
JTAGEN
ICS<1:0>
FICD
FICD
Immediate JTAG Enable bit
1= JTAG is enabled
0= JTAG is disabled
Immediate ICD Communication Channel Select Enable bits
11= Communicates on PGEC1 and PGED1
10= Communicates on PGEC2 and PGED2
01= Communicates on PGEC3 and PGED3
00= Reserved, do not use.
2008-2014 Microchip Technology Inc.
DS70000318G-page 269
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
21.2 On-Chip Voltage Regulator
21.3 BOR: Brown-out Reset
The
dsPIC33FJ06GS101/X02
and
The Brown-out Reset (BOR) module is based on an
internal voltage reference circuit. The main purpose of
the BOR module is to generate a device Reset when a
brown-out condition occurs. Brown-out conditions are
generally caused by glitches on the AC mains (for
example, missing portions of the AC cycle waveform
due to bad power transmission lines, or voltage sags
due to excessive current draw when a large inductive
load is turned on).
dsPIC33FJ16GSX02/X04 devices power their core
digital logic at a nominal 2.5V. This can create a conflict
for designs that are required to operate at a higher typical
voltage, such as 3.3V. To simplify system design, all
devices
in
the
dsPIC33FJ06GS101/X02
and
dsPIC33FJ16GSX02/X04 families incorporate an on-chip
regulator that allows the device to run its core logic from
VDD.
The regulator provides power to the core from the other
VDD pins. When the regulator is enabled, a low-ESR
(less than 5 ohms) capacitor (such as tantalum or
ceramic) must be connected to the VCAP pin
(Figure 21-1). This helps to maintain the stability of the
regulator. The recommended value for the filter
capacitor is provided in Table 24-13 located in
Section 24.1 “DC Characteristics”.
A BOR generates a Reset pulse, which resets the
device. The BOR selects the clock source, based on
the device Configuration bit values (FNOSC<2:0> and
POSCMD<1:0>).
If an oscillator mode is selected, the BOR activates the
Oscillator Start-up Timer (OST). The system clock is
held until OST expires. If the PLL is used, the clock is
held until the LOCK bit (OSCCON<5>) is ‘1’.
Note:
It is important for the low-ESR capacitor to
be placed as close as possible to the VCAP
pin.
Concurrently, the PWRT time-out (TPWRT) is applied
before the internal Reset is released. If TPWRT = 0 and
a crystal oscillator is being used, then a nominal delay
of TFSCM = 100 is applied. The total delay in this case
is TFSCM.
On a POR, it takes approximately 20 s for the on-chip
voltage regulator to generate an output voltage. During
this time, designated as TSTARTUP, code execution is
disabled. TSTARTUP is applied every time the device
resumes operation after any power-down.
The BOR Status bit (RCON<1>) is set to indicate that a
BOR has occurred. The BOR circuit continues to
operate while in Sleep or Idle modes and resets the
device should VDD fall below the BOR threshold
voltage.
FIGURE 21-1:
CONNECTIONS FOR THE
ON-CHIP VOLTAGE
REGULATOR(1,2,3)
3.3V
dsPIC33F
VDD
VCAP
VSS
CEFC
10 µF
Tantalum
Note 1: These are typical operating voltages. Refer
to Table 24-13 located in Section 24.1 “DC
Characteristics” for the full operating
ranges of VDD.
2: It is important for the low-ESR capacitor to
be placed as close as possible to the
VCAP pin.
3:
Typical VCAP pin voltage = 2.5V when
VDD VDDMIN.
DS70000318G-page 270
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
21.4.2
SLEEP AND IDLE MODES
21.4 Watchdog Timer (WDT)
If the WDT is enabled, it will continue to run during
Sleep or Idle modes. When the WDT time-out occurs,
the device will wake the device and code execution will
continue from where the PWRSAV instruction was
executed. The corresponding SLEEP bit (RCON<3>)
or IDLE bit (RCON<2>) will need to be cleared in
software after the device wakes up.
For
the
dsPIC33FJ06GS101/X02
and
dsPIC33FJ16GSX02/X04 devices, the WDT is driven
by the LPRC oscillator. When the WDT is enabled, the
clock source is also enabled.
21.4.1
PRESCALER/POSTSCALER
The nominal WDT clock source from LPRC is 32 kHz.
This feeds a prescaler that can be configured for either
5-bit (divide-by-32) or 7-bit (divide-by-128) operation.
The prescaler is set by the WDTPRE Configuration bit.
With a 32 kHz input, the prescaler yields a nominal
WDT time-out period (TWDT) of 1 ms in 5-bit mode, or
4 ms in 7-bit mode.
21.4.3
ENABLING WDT
The WDT is enabled or disabled by the FWDTEN
Configuration bit in the FWDT Configuration register.
When the FWDTEN Configuration bit is set, the WDT is
always enabled.
The WDT can be optionally controlled in software when
the FWDTEN Configuration bit has been programmed
to ‘0’. The WDT is enabled in software by setting the
SWDTEN control bit (RCON<5>). The SWDTEN
control bit is cleared on any device Reset. The software
WDT option allows the user application to enable the
WDT for critical code segments and disable the WDT
during non-critical segments for maximum power
savings.
A variable postscaler divides down the WDT prescaler
output and allows for a wide range of time-out periods.
The postscaler is controlled by the WDTPOST<3:0>
Configuration bits (FWDT<3:0>) which allow the
selection of 16 settings, from 1:1 to 1:32,768. Using the
prescaler and postscaler, time-out periods ranging from
1 ms to 131 seconds can be achieved.
The WDT, prescaler and postscaler are reset:
• On any device Reset
Note:
If the WINDIS bit (FWDT<6>) is cleared,
the CLRWDTinstruction should be executed
by the application software only during the
last 1/4 of the WDT period. This CLRWDT
window can be determined by using a timer.
If a CLRWDTinstruction is executed before
this window, a WDT Reset occurs.
• On the completion of a clock switch, whether
invoked by software (i.e., setting the OSWEN bit
after changing the NOSC<2:0> bits) or by
hardware (i.e., Fail-Safe Clock Monitor)
• When a PWRSAVinstruction is executed
(i.e., Sleep or Idle mode is entered)
• When the device exits Sleep or Idle mode to
resume normal operation
• By a CLRWDTinstruction during normal execution
The WDT flag bit, WDTO (RCON<4>), is not automatically
cleared following a WDT time-out. To detect subsequent
WDT events, the flag must be cleared in software.
Note:
The CLRWDT and PWRSAV instructions
clear the prescaler and postscaler counts
when executed.
FIGURE 21-2:
WDT BLOCK DIAGRAM
All Device Resets
Transition to New Clock Source
Exit Sleep or Idle Mode
PWRSAVInstruction
CLRWDTInstruction
Watchdog Timer
Sleep/Idle
WDTPRE
Prescaler
WDTPOST<3:0>
SWDTEN
FWDTEN
WDT
Wake-up
1
0
RS
RS
Postscaler
(Divide-by-N2)
WDT
Reset
(Divide-by-N1)
LPRC Clock
WDT Window Select
WINDIS
CLRWDTInstruction
2008-2014 Microchip Technology Inc.
DS70000318G-page 271
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
21.5 JTAG Interface
21.7 In-Circuit Debugger
The
dsPIC33FJ06GS101/X02
and
The
dsPIC33FJ06GS101/X02
and
dsPIC33FJ16GSX02/X04 devices implement a JTAG
interface, which supports boundary scan device
testing. Detailed information on this interface will be
provided in future revisions of the document.
dsPIC33FJ16GSX02/X04 devices provide simple
debugging functionality through the PGECx (Emula-
tion/Debug Clock) and PGEDx (Emulation/Debug
Data) pin functions.
Any of the three pairs of debugging clock/data pins can
be used:
21.6
In-Circuit Serial Programming
• PGEC1 and PGED1
• PGEC2 and PGED2
• PGEC3 and PGED3
The
dsPIC33FJ06GS101/X02
and
dsPIC33FJ16GSX02/X04 family of Digital Signal
Controllers can be serially programmed while in the
end application circuit. This is done with two lines for
clock and data and three other lines for power, ground
and the programming sequence. Serial programming
allows customers to manufacture boards with
unprogrammed devices and then program the Digital
Signal Controller just before shipping the product.
Serial programming also allows the most recent
firmware or a custom firmware to be programmed.
Refer to the “dsPIC33F/PIC24H Flash Programming
Specification” (DS70152) for details about In-Circuit
Serial Programming (ICSP).
To use the in-circuit debugger function of the device,
the design must implement ICSP connections to
MCLR, VDD, VSS, and the PGECx/PGEDx pin pair. In
addition, when the feature is enabled, some of the
resources are not available for general use. These
resources include the first 80 bytes of data RAM and
two I/O pins.
Any of the three pairs of programming clock/data pins
can be used:
• PGEC1 and PGED1
• PGEC2 and PGED2
• PGEC3 and PGED3
DS70000318G-page 272
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
The code protection features are controlled by the
Configuration registers: FBS and FGS.
21.8 Code Protection and
CodeGuard™ Security
Secure segment and RAM protection is not implemented
The
dsPIC33FJ06GS101/X02
and
in
dsPIC33FJ06GS101/X02
and
dsPIC33FJ16GSX02/X04 devices offer the intermediate
implementation of CodeGuard™ Security. CodeGuard
Security enables multiple parties to securely share
resources (memory, interrupts and peripherals) on a
single chip. This feature helps protect individual
Intellectual Property (IP) in collaborative system designs.
dsPIC33FJ16GSX02/X04 devices.
Note: Refer to “CodeGuard™ Security”
(DS70199) for further information on
CodeGuard Security usage, configuration
and operation.
When coupled with software encryption libraries, Code-
Guard™ Security can be used to securely update Flash
even when multiple IPs reside on a single chip.
TABLE 21-3: CODE FLASH SECURITY
SEGMENT SIZES FOR
6-Kbyte DEVICES
TABLE 21-4: CODE FLASH SECURITY
SEGMENT SIZES FOR
16-Kbyte DEVICES
Configuration Bits
Configuration Bits
000000h
VS = 256 IW
000000h
VS = 256 IW
0001FEh
0001FEh
000200h
0003FEh
000200h
0003FEh
BSS<2:0> = x11
000400h
0007FEh
000800h
000FFEh
001000h
BSS<2:0> = x11
000400h
0007FEh
000800h
000FFEh
001000h
GS = 1792 IW
0K
0K
GS = 5376 IW
002BFEh
002BFEh
000000h
000000h
VS = 256 IW
BS = 256 IW
VS = 256 IW
BS = 256 IW
0001FEh
000200h
0001FEh
000200h
0003FEh
0003FEh
BSS<2:0> = x10
000400h
BSS<2:0> = x10
000400h
0007FEh
000800h
000FFEh
001000h
0007FEh
000800h
000FFEh
001000h
GS = 1536 IW
256
256
GS = 5120 IW
002BFEh
002BFEh
000000h
000000h
VS = 256 IW
BS = 768 IW
GS = 1024 IW
VS = 256 IW
BS = 768 IW
0001FEh
000200h
0001FEh
000200h
0003FEh
0003FEh
BSS<2:0> = x01
000400h
BSS<2:0> = x01
000400h
0007FEh
000800h
000FFEh
001000h
0007FEh
000800h
000FFEh
001000h
768
768
GS = 4608 IW
002BFEh
002BFEh
000000h
000000h
VS = 256 IW
BS = 1792 IW
VS = 256 IW
BS = 1792 IW
0001FEh
000200h
0001FEh
000200h
0003FEh
0003FEh
BSS<2:0> = x00
000400h
BSS<2:0> = x00
000400h
0007FEh
000800h
000FFEh
001000h
0007FEh
000800h
000FFEh
001000h
1792
1792
GS = 3584 IW
002BFEh
002BFEh
2008-2014 Microchip Technology Inc.
DS70000318G-page 273
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 274
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Most bit-oriented instructions (including simple
rotate/shift instructions) have two operands:
22.0 INSTRUCTION SET SUMMARY
Note:
This data sheet summarizes the features
of the dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 devices. It is
not intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to the
latest sections in the “dsPIC33F/PIC24H
Family Reference Manual”, which are
available on the Microchip web site
(www.microchip.com).
• The W register (with or without an address
modifier) or file register (specified by the value of
‘Ws’ or ‘f’)
• The bit in the W register or file register
(specified by a literal value or indirectly by the
contents of register ‘Wb’)
The literal instructions that involve data movement can
use some of the following operands:
• A literal value to be loaded into a W register or file
register (specified by ‘k’)
The dsPIC33F instruction set is identical to that of the
dsPIC30F.
• The W register or file register where the literal
value is to be loaded (specified by ‘Wb’ or ‘f’)
Most instructions are a single program memory word
(24 bits). Only three instructions require two program
memory locations.
However, literal instructions that involve arithmetic or
logical operations use some of the following operands:
• The first source operand, which is a register ‘Wb’
without any address modifier
Each single-word instruction is a 24-bit word, divided
into an 8-bit opcode, which specifies the instruction
type and one or more operands, which further specify
the operation of the instruction.
• The second source operand, which is a literal
value
• The destination of the result (only if not the same
as the first source operand), which is typically a
register ‘Wd’ with or without an address modifier
The instruction set is highly orthogonal and is grouped
into five basic categories:
• Word or byte-oriented operations
• Bit-oriented operations
• Literal operations
The MACclass of DSP instructions can use some of the
following operands:
• The accumulator (A or B) to be used (required
operand)
• DSP operations
• Control operations
• The W registers to be used as the two operands
• The X and Y address space prefetch operations
• The X and Y address space prefetch destinations
• The accumulator write-back destination
Table 22-1 shows the general symbols used in
describing the instructions.
The dsPIC33F instruction set summary in Table 22-2
lists all the instructions, along with the status flags
affected by each instruction.
The other DSP instructions do not involve any
multiplication and can include:
Most word or byte-oriented W register instructions
(including barrel shift instructions) have three
operands:
• The accumulator to be used (required)
• The source or destination operand (designated as
Wso or Wdo, respectively) with or without an
address modifier
• The first source operand, which is typically a
register ‘Wb’ without any address modifier
• The amount of shift specified by a W register,
‘Wn’, or a literal value
• The second source operand, which is typically a
register ‘Ws’ with or without an address modifier
The control instructions can use some of the following
operands:
• The destination of the result, which is typically a
register ‘Wd’ with or without an address modifier
• A program memory address
However, word or byte-oriented file register instructions
have two operands:
• The mode of the Table Read and Table Write
instructions
• The file register specified by the value, ‘f’
• The destination, which could be either the file
register, ‘f’, or the W0 register, which is denoted
as ‘WREG’
2008-2014 Microchip Technology Inc.
DS70000318G-page 275
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Most instructions are
a
single word. Certain
(unconditional/computed branch), indirect CALL/GOTO,
all Table Reads and Table Writes and RETURN/RETFIE
instructions, which are single-word instructions but take
two or three cycles. Certain instructions that involve
skipping over the subsequent instruction require either
two or three cycles if the skip is performed, depending
on whether the instruction being skipped is a single-word
or two-word instruction. Moreover, double-word moves
require two cycles.
double-word instructions are designed to provide all the
required information in these 48 bits. In the second
word, the 8 MSbs are ‘0’s. If this second word is
executed as an instruction (by itself), it will execute as
a NOP.
The double-word instructions execute in two instruction
cycles.
Most single-word instructions are executed in a single
instruction cycle, unless a conditional test is true, or the
Program Counter is changed as a result of the
instruction. In these cases, the execution takes two
instruction cycles with the additional instruction cycle(s)
executed as a NOP. Notable exceptions are the BRA
Note:
For more details on the instruction set,
refer to the “16-bit MCU and DSC
Programmer’s
Reference
Manual”
(DS70157).
TABLE 22-1: SYMBOLS USED IN OPCODE DESCRIPTIONS
Field
Description
#text
(text)
[text]
{ }
Means literal defined by “text”
Means “content of text”
Means “the location addressed by text”
Optional field or operation
Register bit field
<n:m>
.b
Byte mode selection
.d
Double-Word mode selection
Shadow register select
.S
.w
Word mode selection (default)
One of two accumulators {A, B}
Acc
AWB
bit4
Accumulator Write-Back Destination Address register {W13, [W13]+ = 2}
4-bit bit selection field (used in word-addressed instructions) {0...15}
MCU Status bits: Carry, Digit Carry, Negative, Overflow, Sticky Zero
Absolute address, label or expression (resolved by the linker)
File register address {0x0000...0x1FFF}
C, DC, N, OV, Z
Expr
f
lit1
1-bit unsigned literal {0,1}
lit4
4-bit unsigned literal {0...15}
lit5
5-bit unsigned literal {0...31}
lit8
8-bit unsigned literal {0...255}
lit10
10-bit unsigned literal {0...255} for Byte mode, {0:1023} for Word mode
14-bit unsigned literal {0...16384}
lit14
lit16
16-bit unsigned literal {0...65535}
lit23
23-bit unsigned literal {0...8388608}; LSb must be ‘0’
Field does not require an entry, can be blank
DSP Status bits: ACCA Overflow, ACCB Overflow, ACCA Saturate, ACCB Saturate
Program Counter
None
OA, OB, SA, SB
PC
Slit10
Slit16
Slit6
Wb
10-bit signed literal {-512...511}
16-bit signed literal {-32768...32767}
6-bit signed literal {-16...16}
Base W register {W0..W15}
Wd
Destination W register { Wd, [Wd], [Wd++], [Wd--], [++Wd], [--Wd] }
Wdo
Destination W register
{ Wnd, [Wnd], [Wnd++], [Wnd--], [++Wnd], [--Wnd], [Wnd+Wb] }
Wm,Wn
Dividend, Divisor Working register pair (Direct Addressing)
DS70000318G-page 276
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 22-1: SYMBOLS USED IN OPCODE DESCRIPTIONS (CONTINUED)
Field
Description
Wm*Wm
Wm*Wn
Multiplicand and Multiplier Working register pair for Square instructions
{W4 * W4,W5 * W5,W6 * W6,W7 * W7}
Multiplicand and Multiplier Working register pair for DSP instructions
{W4 * W5,W4 * W6,W4 * W7,W5 * W6,W5 * W7,W6 * W7}
Wn
One of 16 Working registers {W0..W15}
Wnd
Wns
WREG
Ws
One of 16 Destination Working registers {W0...W15}
One of 16 Source Working registers {W0...W15}
W0 (Working register used in file register instructions)
Source W register { Ws, [Ws], [Ws++], [Ws--], [++Ws], [--Ws] }
Wso
Source W register
{ Wns, [Wns], [Wns++], [Wns--], [++Wns], [--Wns], [Wns+Wb] }
Wx
X Data Space Prefetch Address register for DSP instructions
{[W8] + = 6, [W8] + = 4, [W8] + = 2, [W8], [W8] - = 6, [W8] - = 4, [W8] - = 2,
[W9] + = 6, [W9] + = 4, [W9] + = 2, [W9], [W9] - = 6, [W9] - = 4, [W9] - = 2,
[W9 + W12], none}
Wxd
Wy
X Data Space Prefetch Destination register for DSP instructions {W4...W7}
Y Data Space Prefetch Address register for DSP instructions
{[W10] + = 6, [W10] + = 4, [W10] + = 2, [W10], [W10] - = 6, [W10] - = 4, [W10] - = 2,
[W11] + = 6, [W11] + = 4, [W11] + = 2, [W11], [W11] - = 6, [W11] - = 4, [W11] - = 2,
[W11 + W12], none}
Wyd
Y Data Space Prefetch Destination register for DSP instructions {W4...W7}
2008-2014 Microchip Technology Inc.
DS70000318G-page 277
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 22-2: INSTRUCTION SET OVERVIEW
Base
Instr
#
Assembly
Mnemonic
# of
# of
Status Flags
Affected
Assembly Syntax
Description
Words Cycles
1
ADD
ADD
ADD
ADD
ADD
ADD
ADD
ADD
ADDC
ADDC
ADDC
ADDC
ADDC
AND
AND
AND
AND
AND
ASR
ASR
ASR
ASR
ASR
BCLR
BCLR
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BRA
BSET
BSET
BSW.C
BSW.Z
BTG
BTG
Acc
Add Accumulators
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
OA,OB,SA,SB
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
OA,OB,SA,SB
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
N,Z
f
f = f + WREG
f,WREG
WREG = f + WREG
1
#lit10,Wn
Wb,Ws,Wd
Wb,#lit5,Wd
Wso,#Slit4,Acc
f
Wd = lit10 + Wd
1
Wd = Wb + Ws
1
Wd = Wb + lit5
1
16-bit Signed Add to Accumulator
f = f + WREG + (C)
1
2
3
4
ADDC
AND
1
f,WREG
WREG = f + WREG + (C)
Wd = lit10 + Wd + (C)
Wd = Wb + Ws + (C)
1
#lit10,Wn
Wb,Ws,Wd
Wb,#lit5,Wd
f
1
1
Wd = Wb + lit5 + (C)
1
f = f .AND. WREG
1
f,WREG
WREG = f .AND. WREG
Wd = lit10 .AND. Wd
1
N,Z
#lit10,Wn
Wb,Ws,Wd
Wb,#lit5,Wd
f
1
N,Z
Wd = Wb .AND. Ws
1
N,Z
Wd = Wb .AND. lit5
1
N,Z
ASR
f = Arithmetic Right Shift f
WREG = Arithmetic Right Shift f
Wd = Arithmetic Right Shift Ws
Wnd = Arithmetic Right Shift Wb by Wns
Wnd = Arithmetic Right Shift Wb by lit5
Bit Clear f
1
C,N,OV,Z
C,N,OV,Z
C,N,OV,Z
N,Z
f,WREG
1
Ws,Wd
1
Wb,Wns,Wnd
Wb,#lit5,Wnd
f,#bit4
Ws,#bit4
C,Expr
1
1
N,Z
5
6
BCLR
BRA
1
None
Bit Clear Ws
1
None
Branch if Carry
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
2
None
GE,Expr
GEU,Expr
GT,Expr
GTU,Expr
LE,Expr
LEU,Expr
LT,Expr
LTU,Expr
N,Expr
Branch if Greater Than or Equal
Branch if Unsigned Greater Than or Equal
Branch if Greater Than
Branch if Unsigned Greater Than
Branch if Less Than or Equal
Branch if Unsigned Less Than or Equal
Branch if Less Than
None
None
None
None
None
None
None
Branch if Unsigned Less Than
Branch if Negative
None
None
NC,Expr
NN,Expr
NOV,Expr
NZ,Expr
OA,Expr
OB,Expr
OV,Expr
SA,Expr
SB,Expr
Expr
Branch if Not Carry
None
Branch if Not Negative
Branch if Not Overflow
Branch if Not Zero
None
None
None
Branch if Accumulator A Overflow
Branch if Accumulator B Overflow
Branch if Overflow
None
None
None
Branch if Accumulator A Saturated
Branch if Accumulator B Saturated
Branch Unconditionally
Branch if Zero
None
None
None
Z,Expr
1 (2)
2
None
Wn
Computed Branch
None
7
8
9
BSET
BSW
f,#bit4
Ws,#bit4
Ws,Wb
Bit Set f
1
None
Bit Set Ws
1
None
Write C bit to Ws<Wb>
Write Z bit to Ws<Wb>
Bit Toggle f
1
None
Ws,Wb
1
None
BTG
f,#bit4
Ws,#bit4
1
None
Bit Toggle Ws
1
None
DS70000318G-page 278
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 22-2: INSTRUCTION SET OVERVIEW (CONTINUED)
Base
Instr
#
Assembly
Mnemonic
# of
# of
Status Flags
Affected
Assembly Syntax
Description
Words Cycles
10
BTSC
BTSS
BTST
BTSC
BTSC
BTSS
BTSS
f,#bit4
Ws,#bit4
f,#bit4
Ws,#bit4
Bit Test f, Skip if Clear
1
1
1
1
1
None
None
None
None
(2 or 3)
Bit Test Ws, Skip if Clear
Bit Test f, Skip if Set
1
(2 or 3)
11
12
1
(2 or 3)
Bit Test Ws, Skip if Set
1
(2 or 3)
BTST
f,#bit4
Ws,#bit4
Ws,#bit4
Ws,Wb
Bit Test f
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
Z
BTST.C
BTST.Z
BTST.C
BTST.Z
BTSTS
Bit Test Ws to C
Bit Test Ws to Z
Bit Test Ws<Wb> to C
Bit Test Ws<Wb> to Z
Bit Test then Set f
Bit Test Ws to C, then Set
Bit Test Ws to Z, then Set
Call Subroutine
C
Z
C
Ws,Wb
Z
13
BTSTS
f,#bit4
Z
C
BTSTS.C Ws,#bit4
BTSTS.Z Ws,#bit4
Z
14
15
CALL
CLR
CALL
CALL
CLR
lit23
None
Wn
Call Indirect Subroutine
f = 0x0000
None
f
None
CLR
WREG
WREG = 0x0000
Ws = 0x0000
None
CLR
Ws
None
CLR
Acc,Wx,Wxd,Wy,Wyd,AWB
Clear Accumulator
Clear Watchdog Timer
f = f
OA,OB,SA,SB
WDTO,Sleep
N,Z
16
17
CLRWDT
COM
CLRWDT
COM
f
COM
COM
CP
f,WREG
Ws,Wd
f
WREG = f
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
N,Z
Wd = Ws
N,Z
18
CP
Compare f with WREG
Compare Wb with lit5
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
CP
Wb,#lit5
Wb,Ws
f
CP
Compare Wb with Ws (Wb – Ws)
Compare f with 0x0000
Compare Ws with 0x0000
Compare f with WREG, with Borrow
Compare Wb with lit5, with Borrow
19
20
CP0
CPB
CP0
CP0
CPB
CPB
CPB
Ws
f
Wb,#lit5
Wb,Ws
Compare Wb with Ws, with Borrow
(Wb – Ws – C)
21
22
23
24
CPSEQ
CPSGT
CPSLT
CPSNE
CPSEQ
CPSGT
CPSLT
CPSNE
Wb, Wn
Wb, Wn
Wb, Wn
Wb, Wn
Compare Wb with Wn, Skip if =
Compare Wb with Wn, Skip if >
Compare Wb with Wn, Skip if <
Compare Wb with Wn, Skip if
1
1
1
1
1
None
None
None
None
(2 or 3)
1
(2 or 3)
1
(2 or 3)
1
(2 or 3)
25
26
DAW
DEC
DAW
Wn
Wn = Decimal Adjust Wn
f = f – 1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C
DEC
f
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
None
DEC
f,WREG
Ws,Wd
f
WREG = f – 1
DEC
Wd = Ws – 1
27
28
DEC2
DISI
DEC2
DEC2
DEC2
DISI
f = f – 2
f,WREG
Ws,Wd
#lit14
WREG = f – 2
Wd = Ws – 2
Disable Interrupts for k Instruction Cycles
2008-2014 Microchip Technology Inc.
DS70000318G-page 279
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 22-2: INSTRUCTION SET OVERVIEW (CONTINUED)
Base
Instr
#
Assembly
Mnemonic
# of
# of
Status Flags
Affected
Assembly Syntax
Description
Words Cycles
29
DIV
DIV.S
DIV.SD
DIV.U
DIV.UD
DIVF
DO
Wm,Wn
Signed 16/16-bit Integer Divide
1
1
1
1
1
2
2
1
18
18
18
18
18
2
N,Z,C,OV
N,Z,C,OV
N,Z,C,OV
N,Z,C,OV
N,Z,C,OV
None
Wm,Wn
Signed 32/16-bit Integer Divide
Wm,Wn
Unsigned 16/16-bit Integer Divide
Unsigned 32/16-bit Integer Divide
Signed 16/16-bit Fractional Divide
Do code to PC + Expr, lit14 + 1 times
Do code to PC + Expr, (Wn) + 1 times
Euclidean Distance (no accumulate)
Wm,Wn
30
31
DIVF
DO
Wm,Wn
#lit14,Expr
Wn,Expr
DO
2
None
32
33
ED
ED
Wm*Wm,Acc,Wx,Wy,Wxd
1
OA,OB,OAB,
SA,SB,SAB
EDAC
EDAC
Wm*Wm,Acc,Wx,Wy,Wxd
Euclidean Distance
1
1
OA,OB,OAB,
SA,SB,SAB
34
35
36
37
38
EXCH
FBCL
FF1L
FF1R
GOTO
EXCH
FBCL
FF1L
FF1R
GOTO
GOTO
INC
Wns,Wnd
Ws,Wnd
Ws,Wnd
Ws,Wnd
Expr
Swap Wns with Wnd
Find Bit Change from Left (MSb) Side
Find First One from Left (MSb) Side
Find First One from Right (LSb) Side
Go to Address
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
None
C
C
C
None
Wn
Go to Indirect
None
39
40
41
INC
f
f = f + 1
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
N,Z
INC
f,WREG
Ws,Wd
WREG = f + 1
INC
Wd = Ws + 1
INC2
IOR
INC2
INC2
INC2
IOR
f
f = f + 2
f,WREG
Ws,Wd
WREG = f + 2
Wd = Ws + 2
f
f = f .IOR. WREG
IOR
f,WREG
#lit10,Wn
Wb,Ws,Wd
Wb,#lit5,Wd
Wso,#Slit4,Acc
WREG = f .IOR. WREG
Wd = lit10 .IOR. Wd
Wd = Wb .IOR. Ws
Wd = Wb .IOR. lit5
Load Accumulator
N,Z
IOR
N,Z
IOR
N,Z
IOR
N,Z
42
LAC
LAC
OA,OB,OAB,
SA,SB,SAB
43
44
LNK
LSR
LNK
LSR
LSR
LSR
LSR
LSR
MAC
#lit14
Link Frame Pointer
1
1
1
1
1
1
1
1
1
1
1
1
1
1
None
C,N,OV,Z
C,N,OV,Z
C,N,OV,Z
N,Z
f
f = Logical Right Shift f
f,WREG
WREG = Logical Right Shift f
Wd = Logical Right Shift Ws
Wnd = Logical Right Shift Wb by Wns
Wnd = Logical Right Shift Wb by lit5
Ws,Wd
Wb,Wns,Wnd
Wb,#lit5,Wnd
N,Z
45
46
MAC
MOV
Wm*Wn,Acc,Wx,Wxd,Wy,Wyd Multiply and Accumulate
,
AWB
OA,OB,OAB,
SA,SB,SAB
MAC
Wm*Wm,Acc,Wx,Wxd,Wy,Wyd Square and Accumulate
1
1
OA,OB,OAB,
SA,SB,SAB
MOV
f,Wn
Move f to Wn
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
None
N,Z
MOV
f
Move f to f
MOV
f,WREG
Move f to WREG
None
None
None
None
None
None
None
None
None
MOV
#lit16,Wn
#lit8,Wn
Wn,f
Move 16-bit Literal to Wn
Move 8-bit Literal to Wn
Move Wn to f
MOV.b
MOV
MOV
Wso,Wdo
Move Ws to Wd
MOV
WREG,f
Move WREG to f
MOV.D
MOV.D
MOVSAC
Wns,Wd
Move Double from W(ns):W(ns + 1) to Wd
Move Double from Ws to W(nd + 1):W(nd)
Prefetch and Store Accumulator
Ws,Wnd
47
MOVSAC
Acc,Wx,Wxd,Wy,Wyd,AWB
DS70000318G-page 280
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 22-2: INSTRUCTION SET OVERVIEW (CONTINUED)
Base
Instr
#
Assembly
Mnemonic
# of
# of
Status Flags
Affected
Assembly Syntax
Description
Words Cycles
48
MPY
MPY
Multiply Wm by Wn to Accumulator
Square Wm to Accumulator
1
1
1
1
1
1
1
1
OA,OB,OAB,
SA,SB,SAB
Wm*Wn,Acc,Wx,Wxd,Wy,Wyd
MPY
OA,OB,OAB,
SA,SB,SAB
Wm*Wm,Acc,Wx,Wxd,Wy,Wyd
49
50
MPY.N
MSC
MPY.N
-(Multiply Wm by Wn) to Accumulator
None
Wm*Wn,Acc,Wx,Wxd,Wy,Wyd
MSC
Wm*Wm,Acc,Wx,Wxd,Wy,Wyd Multiply and Subtract from Accumulator
OA,OB,OAB,
SA,SB,SAB
,
AWB
51
MUL
MUL.SS
MUL.SU
MUL.US
MUL.UU
Wb,Ws,Wnd
Wb,Ws,Wnd
Wb,Ws,Wnd
Wb,Ws,Wnd
{Wnd + 1, Wnd} = signed(Wb) * signed(Ws)
{Wnd + 1, Wnd} = signed(Wb) * unsigned(Ws)
{Wnd + 1, Wnd} = unsigned(Wb) * signed(Ws)
1
1
1
1
1
1
1
1
None
None
None
None
{Wnd + 1, Wnd} = unsigned(Wb) *
unsigned(Ws)
MUL.SU
MUL.UU
Wb,#lit5,Wnd
Wb,#lit5,Wnd
{Wnd + 1, Wnd} = signed(Wb) * unsigned(lit5)
1
1
1
1
None
None
{Wnd + 1, Wnd} = unsigned(Wb) *
unsigned(lit5)
MUL
NEG
f
W3:W2 = f * WREG
Negate Accumulator
1
1
1
1
None
52
NEG
Acc
OA,OB,OAB,
SA,SB,SAB
NEG
f
f = f + 1
1
1
C,DC,N,OV,Z
NEG
f,WREG
Ws,Wd
WREG = f + 1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
C,DC,N,OV,Z
C,DC,N,OV,Z
None
NEG
Wd = Ws + 1
53
54
NOP
POP
NOP
No Operation
NOPR
POP
No Operation
None
f
Pop f from Top-of-Stack (TOS)
Pop from Top-of-Stack (TOS) to Wdo
None
POP
Wdo
Wnd
None
POP.D
Pop from Top-of-Stack (TOS) to
W(nd):W(nd + 1)
None
POP.S
PUSH
Pop Shadow Registers
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
All
None
None
None
None
WDTO,Sleep
None
None
None
None
None
None
None
None
C,N,Z
C,N,Z
C,N,Z
N,Z
55
PUSH
f
Push f to Top-of-Stack (TOS)
Push Wso to Top-of-Stack (TOS)
Push W(ns):W(ns + 1) to Top-of-Stack (TOS)
Push Shadow Registers
1
PUSH
Wso
Wns
1
PUSH.D
PUSH.S
PWRSAV
RCALL
RCALL
REPEAT
REPEAT
RESET
RETFIE
RETLW
RETURN
RLC
2
1
56
57
PWRSAV
RCALL
#lit1
Expr
Wn
Go into Sleep or Idle mode
Relative Call
1
2
Computed Call
2
58
REPEAT
#lit14
Wn
Repeat Next Instruction lit14 + 1 times
Repeat Next Instruction (Wn) + 1 times
Software Device Reset
1
1
59
60
61
62
63
RESET
RETFIE
RETLW
RETURN
RLC
1
Return from interrupt
3 (2)
#lit10,Wn
Return with Literal in Wn
3 (2)
Return from Subroutine
3 (2)
1
f
f = Rotate Left through Carry f
WREG = Rotate Left through Carry f
Wd = Rotate Left through Carry Ws
f = Rotate Left (No Carry) f
RLC
f,WREG
Ws,Wd
f
1
RLC
1
64
65
RLNC
RRC
RLNC
1
RLNC
f,WREG
Ws,Wd
f
WREG = Rotate Left (No Carry) f
Wd = Rotate Left (No Carry) Ws
f = Rotate Right through Carry f
WREG = Rotate Right through Carry f
Wd = Rotate Right through Carry Ws
1
N,Z
RLNC
1
N,Z
RRC
1
C,N,Z
C,N,Z
C,N,Z
RRC
f,WREG
Ws,Wd
1
RRC
1
2008-2014 Microchip Technology Inc.
DS70000318G-page 281
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 22-2: INSTRUCTION SET OVERVIEW (CONTINUED)
Base
Instr
#
Assembly
Mnemonic
# of
# of
Status Flags
Affected
Assembly Syntax
Description
Words Cycles
66
RRNC
SAC
RRNC
RRNC
RRNC
SAC
f
f = Rotate Right (No Carry) f
WREG = Rotate Right (No Carry) f
Wd = Rotate Right (No Carry) Ws
Store Accumulator
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
N,Z
N,Z
f,WREG
Ws,Wd
N,Z
67
Acc,#Slit4,Wdo
None
None
C,N,Z
None
None
None
SAC.R
SE
Acc,#Slit4,Wdo
Store Rounded Accumulator
Wnd = Sign-Extended Ws
f = 0xFFFF
68
69
SE
Ws,Wnd
f
SETM
SETM
SETM
SETM
SFTAC
WREG
Ws
WREG = 0xFFFF
Ws = 0xFFFF
70
71
SFTAC
SL
Acc,Wn
Arithmetic Shift Accumulator by (Wn)
OA,OB,OAB,
SA,SB,SAB
SFTAC
Acc,#Slit6
Arithmetic Shift Accumulator by Slit6
1
1
OA,OB,OAB,
SA,SB,SAB
SL
SL
SL
SL
SL
SUB
f
f = Left Shift f
1
1
1
1
1
1
1
1
1
1
1
1
C,N,OV,Z
C,N,OV,Z
C,N,OV,Z
N,Z
f,WREG
Ws,Wd
WREG = Left Shift f
Wd = Left Shift Ws
Wb,Wns,Wnd
Wb,#lit5,Wnd
Acc
Wnd = Left Shift Wb by Wns
Wnd = Left Shift Wb by lit5
Subtract Accumulators
N,Z
72
SUB
OA,OB,OAB,
SA,SB,SAB
SUB
SUB
SUB
SUB
SUB
SUBB
f
f = f – WREG
1
1
1
1
1
1
1
1
1
1
1
1
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
f,WREG
#lit10,Wn
Wb,Ws,Wd
Wb,#lit5,Wd
f
WREG = f – WREG
Wn = Wn – lit10
Wd = Wb – Ws
Wd = Wb – lit5
73
SUBB
f = f – WREG – (C)
SUBB
SUBB
SUBB
f,WREG
WREG = f – WREG – (C)
Wn = Wn – lit10 – (C)
Wd = Wb – Ws – (C)
1
1
1
1
1
1
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
#lit10,Wn
Wb,Ws,Wd
SUBB
SUBR
SUBR
SUBR
SUBR
SUBBR
SUBBR
Wb,#lit5,Wd
f
Wd = Wb – lit5 – (C)
f = WREG – f
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
C,DC,N,OV,Z
74
75
SUBR
f,WREG
Wb,Ws,Wd
Wb,#lit5,Wd
f
WREG = WREG – f
Wd = Ws – Wb
Wd = lit5 – Wb
SUBBR
f = WREG – f – (C)
WREG = WREG – f – (C)
f,WREG
SUBBR
SUBBR
SWAP.b
SWAP
TBLRDH
TBLRDL
TBLWTH
TBLWTL
ULNK
XOR
Wb,Ws,Wd
Wb,#lit5,Wd
Wn
Wd = Ws – Wb – (C)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1
C,DC,N,OV,Z
C,DC,N,OV,Z
None
None
None
None
None
None
None
N,Z
Wd = lit5 – Wb – (C)
76
SWAP
Wn = Nibble Swap Wn
Wn = Byte Swap Wn
Wn
77
78
79
80
81
82
TBLRDH
TBLRDL
TBLWTH
TBLWTL
ULNK
Ws,Wd
Ws,Wd
Ws,Wd
Ws,Wd
Read Prog<23:16> to Wd<7:0>
Read Prog<15:0> to Wd
Write Ws<7:0> to Prog<23:16>
Write Ws to Prog<15:0>
Unlink Frame Pointer
f = f .XOR. WREG
XOR
f
XOR
f,WREG
WREG = f .XOR. WREG
Wd = lit10 .XOR. Wd
Wd = Wb .XOR. Ws
N,Z
XOR
#lit10,Wn
Wb,Ws,Wd
Wb,#lit5,Wd
Ws,Wnd
N,Z
XOR
N,Z
XOR
Wd = Wb .XOR. lit5
N,Z
83
ZE
ZE
Wnd = Zero-Extend Ws
C,Z,N
DS70000318G-page 282
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
23.1 MPLAB X Integrated Development
Environment Software
23.0 DEVELOPMENT SUPPORT
The PIC® microcontrollers (MCU) and dsPIC® Digital
Signal Controllers (DSC) are supported with a full
range of software and hardware development tools:
The MPLAB X IDE is a single, unified graphical user
interface for Microchip and third-party software, and
hardware development tool that runs on Windows®,
Linux and Mac OS® X. Based on the NetBeans IDE,
MPLAB X IDE is an entirely new IDE with a host of free
software components and plug-ins for high-
performance application development and debugging.
Moving between tools and upgrading from software
simulators to hardware debugging and programming
tools is simple with the seamless user interface.
• Integrated Development Environment
- MPLAB® X IDE Software
• Compilers/Assemblers/Linkers
- MPLAB XC Compiler
- MPASMTM Assembler
- MPLINKTM Object Linker/
MPLIBTM Object Librarian
- MPLAB Assembler/Linker/Librarian for
Various Device Families
With complete project management, visual call graphs,
a configurable watch window and a feature-rich editor
that includes code completion and context menus,
MPLAB X IDE is flexible and friendly enough for new
users. With the ability to support multiple tools on
multiple projects with simultaneous debugging, MPLAB
X IDE is also suitable for the needs of experienced
users.
• Simulators
- MPLAB X SIM Software Simulator
• Emulators
- MPLAB REAL ICE™ In-Circuit Emulator
• In-Circuit Debuggers/Programmers
- MPLAB ICD 3
Feature-Rich Editor:
- PICkit™ 3
• Color syntax highlighting
• Device Programmers
- MPLAB PM3 Device Programmer
• Smart code completion makes suggestions and
provides hints as you type
• Low-Cost Demonstration/Development Boards,
Evaluation Kits and Starter Kits
• Automatic code formatting based on user-defined
rules
• Third-party development tools
• Live parsing
User-Friendly, Customizable Interface:
• Fully customizable interface: toolbars, toolbar
buttons, windows, window placement, etc.
• Call graph window
Project-Based Workspaces:
• Multiple projects
• Multiple tools
• Multiple configurations
• Simultaneous debugging sessions
File History and Bug Tracking:
• Local file history feature
• Built-in support for Bugzilla issue tracker
2008-2014 Microchip Technology Inc.
DS70000318G-page 283
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
23.2 MPLAB XC Compilers
23.4 MPLINK Object Linker/
MPLIB Object Librarian
The MPLAB XC Compilers are complete ANSI C
compilers for all of Microchip’s 8, 16 and 32-bit MCU
and DSC devices. These compilers provide powerful
integration capabilities, superior code optimization and
ease of use. MPLAB XC Compilers run on Windows,
Linux or MAC OS X.
The MPLINK Object Linker combines relocatable
objects created by the MPASM Assembler. It can link
relocatable objects from precompiled libraries, using
directives from a linker script.
The MPLIB Object Librarian manages the creation and
modification of library files of precompiled code. When
a routine from a library is called from a source file, only
the modules that contain that routine will be linked in
with the application. This allows large libraries to be
used efficiently in many different applications.
For easy source level debugging, the compilers provide
debug information that is optimized to the MPLAB X
IDE.
The free MPLAB XC Compiler editions support all
devices and commands, with no time or memory
restrictions, and offer sufficient code optimization for
most applications.
The object linker/library features include:
• Efficient linking of single libraries instead of many
smaller files
MPLAB XC Compilers include an assembler, linker and
utilities. The assembler generates relocatable object
files that can then be archived or linked with other
relocatable object files and archives to create an exe-
cutable file. MPLAB XC Compiler uses the assembler
to produce its object file. Notable features of the
assembler include:
• Enhanced code maintainability by grouping
related modules together
• Flexible creation of libraries with easy module
listing, replacement, deletion and extraction
23.5 MPLAB Assembler, Linker and
Librarian for Various Device
Families
• Support for the entire device instruction set
• Support for fixed-point and floating-point data
• Command-line interface
MPLAB Assembler produces relocatable machine
code from symbolic assembly language for PIC24,
PIC32 and dsPIC DSC devices. MPLAB XC Compiler
uses the assembler to produce its object file. The
assembler generates relocatable object files that can
then be archived or linked with other relocatable object
files and archives to create an executable file. Notable
features of the assembler include:
• Rich directive set
• Flexible macro language
• MPLAB X IDE compatibility
23.3 MPASM Assembler
The MPASM Assembler is a full-featured, universal
macro assembler for PIC10/12/16/18 MCUs.
• Support for the entire device instruction set
• Support for fixed-point and floating-point data
• Command-line interface
The MPASM Assembler generates relocatable object
files for the MPLINK Object Linker, Intel® standard HEX
files, MAP files to detail memory usage and symbol
reference, absolute LST files that contain source lines
and generated machine code, and COFF files for
debugging.
• Rich directive set
• Flexible macro language
• MPLAB X IDE compatibility
The MPASM Assembler features include:
• Integration into MPLAB X IDE projects
• User-defined macros to streamline
assembly code
• Conditional assembly for multipurpose
source files
• Directives that allow complete control over the
assembly process
DS70000318G-page 284
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
23.6 MPLAB X SIM Software Simulator
23.8 MPLAB ICD 3 In-Circuit Debugger
System
The MPLAB X SIM Software Simulator allows code
development in a PC-hosted environment by simulat-
ing the PIC MCUs and dsPIC DSCs on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a comprehensive stimulus controller. Registers can be
logged to files for further run-time analysis. The trace
buffer and logic analyzer display extend the power of
the simulator to record and track program execution,
actions on I/O, most peripherals and internal registers.
The MPLAB ICD 3 In-Circuit Debugger System is
Microchip’s most cost-effective, high-speed hardware
debugger/programmer for Microchip Flash DSC and
MCU devices. It debugs and programs PIC Flash
microcontrollers and dsPIC DSCs with the powerful,
yet easy-to-use graphical user interface of the MPLAB
IDE.
The MPLAB ICD 3 In-Circuit Debugger probe is
connected to the design engineer’s PC using a high-
speed USB 2.0 interface and is connected to the target
with a connector compatible with the MPLAB ICD 2 or
MPLAB REAL ICE systems (RJ-11). MPLAB ICD 3
supports all MPLAB ICD 2 headers.
The MPLAB X SIM Software Simulator fully supports
symbolic debugging using the MPLAB XC Compilers,
and the MPASM and MPLAB Assemblers. The soft-
ware simulator offers the flexibility to develop and
debug code outside of the hardware laboratory envi-
ronment, making it an excellent, economical software
development tool.
23.9 PICkit 3 In-Circuit Debugger/
Programmer
The MPLAB PICkit 3 allows debugging and program-
ming of PIC and dsPIC Flash microcontrollers at a most
affordable price point using the powerful graphical user
interface of the MPLAB IDE. The MPLAB PICkit 3 is
connected to the design engineer’s PC using a full-
speed USB interface and can be connected to the
target via a Microchip debug (RJ-11) connector (com-
patible with MPLAB ICD 3 and MPLAB REAL ICE). The
connector uses two device I/O pins and the Reset line
to implement in-circuit debugging and In-Circuit Serial
Programming™ (ICSP™).
23.7 MPLAB REAL ICE In-Circuit
Emulator System
The MPLAB REAL ICE In-Circuit Emulator System is
Microchip’s next generation high-speed emulator for
Microchip Flash DSC and MCU devices. It debugs and
programs all 8, 16 and 32-bit MCU, and DSC devices
with the easy-to-use, powerful graphical user interface of
the MPLAB X IDE.
The emulator is connected to the design engineer’s
PC using a high-speed USB 2.0 interface and is
connected to the target with either a connector
compatible with in-circuit debugger systems (RJ-11)
or with the new high-speed, noise tolerant, Low-
Voltage Differential Signal (LVDS) interconnection
(CAT5).
23.10 MPLAB PM3 Device Programmer
The MPLAB PM3 Device Programmer is a universal,
CE compliant device programmer with programmable
voltage verification at VDDMIN and VDDMAX for
maximum reliability. It features a large LCD display
(128 x 64) for menus and error messages, and a mod-
ular, detachable socket assembly to support various
package types. The ICSP cable assembly is included
as a standard item. In Stand-Alone mode, the MPLAB
PM3 Device Programmer can read, verify and program
PIC devices without a PC connection. It can also set
code protection in this mode. The MPLAB PM3
connects to the host PC via an RS-232 or USB cable.
The MPLAB PM3 has high-speed communications and
optimized algorithms for quick programming of large
memory devices, and incorporates an MMC card for file
storage and data applications.
The emulator is field upgradable through future firmware
downloads in MPLAB X IDE. MPLAB REAL ICE offers
significant advantages over competitive emulators
including full-speed emulation, run-time variable
watches, trace analysis, complex breakpoints, logic
probes, a ruggedized probe interface and long (up to
three meters) interconnection cables.
2008-2014 Microchip Technology Inc.
DS70000318G-page 285
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
23.11 Demonstration/Development
Boards, Evaluation Kits and
Starter Kits
23.12 Third-Party Development Tools
Microchip also offers a great collection of tools from
third-party vendors. These tools are carefully selected
to offer good value and unique functionality.
A wide variety of demonstration, development and
evaluation boards for various PIC MCUs and dsPIC
DSCs allows quick application development on fully
functional systems. Most boards include prototyping
areas for adding custom circuitry and provide applica-
tion firmware and source code for examination and
modification.
• Device Programmers and Gang Programmers
from companies, such as SoftLog and CCS
• Software Tools from companies, such as Gimpel
and Trace Systems
• Protocol Analyzers from companies, such as
Saleae and Total Phase
The boards support a variety of features, including LEDs,
temperature sensors, switches, speakers, RS-232
interfaces, LCD displays, potentiometers and additional
EEPROM memory.
• Demonstration Boards from companies, such as
MikroElektronika, Digilent® and Olimex
• Embedded Ethernet Solutions from companies,
such as EZ Web Lynx, WIZnet and IPLogika®
The demonstration and development boards can be
used in teaching environments, for prototyping custom
circuits and for learning about various microcontroller
applications.
In addition to the PICDEM™ and dsPICDEM™
demonstration/development board series of circuits,
Microchip has a line of evaluation kits and demonstra-
®
tion software for analog filter design, KEELOQ security
ICs, CAN, IrDA®, PowerSmart battery management,
SEEVAL® evaluation system, Sigma-Delta ADC, flow
rate sensing, plus many more.
Also available are starter kits that contain everything
needed to experience the specified device. This usually
includes a single application and debug capability, all
on one board.
Check the Microchip web page (www.microchip.com)
for the complete list of demonstration, development
and evaluation kits.
DS70000318G-page 286
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
24.0 ELECTRICAL CHARACTERISTICS
This section provides an overview of dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 electrical characteristics.
Additional information will be provided in future revisions of this document as it becomes available.
Absolute maximum ratings for the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 family are listed below.
Exposure to these maximum rating conditions for extended periods may affect device reliability. Functional operation of
the device at these or any other conditions above the parameters indicated in the operation listings of this specification
is not implied.
(1)
Absolute Maximum Ratings
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V
Voltage on any pin that is not 5V tolerant, with respect to VSS(3) ................................................... -0.3V to (VDD + 0.3V)
Voltage on any 5V tolerant pin with respect to VSS, when VDD 3.0V(3) ................................................. -0.3V to +5.6V
Voltage on any 5V tolerant pin with respect to Vss, when VDD < 3.0V(3)........................................ -0.3V to (VDD + 0.3V)
Maximum current out of VSS pin ...........................................................................................................................300 mA
Maximum current into VDD pin(2)...........................................................................................................................250 mA
Maximum current sourced/sunk by any 4x I/O pin..................................................................................................15 mA
Maximum current sourced/sunk by any 8x I/O pin..................................................................................................25 mA
Maximum current sourced/sunk by any 16x I/O pin................................................................................................45 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports(2)...............................................................................................................200mA
Note 1: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only, and functional operation of the device at those or any other conditions
above those indicated in the operation listings of this specification is not implied. Exposure to maximum
rating conditions for extended periods may affect device reliability.
2: Maximum allowable current is a function of device maximum power dissipation (see Table 24-2).
3: See the “Pin Diagrams” section for 5V tolerant pins.
2008-2014 Microchip Technology Inc.
DS70000318G-page 287
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
24.1 DC Characteristics
TABLE 24-1: OPERATING MIPS VS. VOLTAGE
Max MIPS
VDD Range
(in Volts)
Temp Range
(in °C)
Characteristic
dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04
—
—
3.0-3.6V(1)
3.0-3.6V(1)
-40°C to +85°C
-40°C to +125°C
40
40
Note 1: Overall functional device operation at VBORMIN < VDD < VDDMIN is tested but not characterized. All device
analog modules such as the ADC, etc., will function but with degraded performance below VDDMIN. Refer
to Parameter BO10 in Table 24-11 for BOR values.
TABLE 24-2: THERMAL OPERATING CONDITIONS
Rating
Industrial Temperature Devices
Symbol
Min
Typ
Max
Unit
Operating Junction Temperature Range
Operating Ambient Temperature Range
TJ
TA
-40
-40
—
—
+125
+85
°C
°C
Extended Temperature Devices
Operating Junction Temperature Range
Operating Ambient Temperature Range
TJ
TA
-40
-40
—
—
+140
+125
°C
°C
Power Dissipation:
Internal chip power dissipation:
PINT = VDD x (IDD – IOH)
PD
PINT + PI/O
W
W
I/O Pin Power Dissipation:
I/O = ({VDD – VOH} x IOH) + (VOL x IOL)
Maximum Allowed Power Dissipation
PDMAX
(TJ – TA)/JA
TABLE 24-3: THERMAL PACKAGING CHARACTERISTICS
Characteristic
Symbol
Typ
Max
Unit
Notes
Package Thermal Resistance, 44-Pin QFN
Package Thermal Resistance, 44-Pin TFQP
Package Thermal Resistance, 28-Pin SPDIP
Package Thermal Resistance, 28-Pin SOIC
Package Thermal Resistance, 28-Pin QFN-S
Package Thermal Resistance, 18-Pin SOIC
Package Thermal Resistance, 44-Pin VTLA
JA
JA
JA
JA
JA
JA
JA
28
39
42
47
34
57
25
—
—
—
—
—
—
—
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
1
1
1
1
1
1
1
Note 1: Junction to ambient thermal resistance, Theta-JA (JA) numbers are achieved by package simulations.
DS70000318G-page 288
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-4: DC TEMPERATURE AND VOLTAGE SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristic
Min
Typ(1)
Max Units
Conditions
Operating Voltage
DC10
DC12
DC16
VDD
Supply Voltage(4)
RAM Data Retention Voltage(2)
3.0
1.8
—
—
—
—
3.6
—
V
V
V
Industrial and Extended
VDR
VPOR
VDD Start Voltage
VSS
to Ensure Internal
Power-on Reset Signal
DC17 SVDD
VDD Rise Rate(3)
0.03
—
—
V/ms 0V-3.0V in 0.1 seconds
to Ensure Internal
Power-on Reset Signal
Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
2: This is the limit to which VDD may be lowered without losing RAM data.
3: These parameters are characterized but not tested in manufacturing.
4: Overall functional device operation at VBORMIN < VDD < VDDMIN is tested but not characterized. All device
analog modules such as the ADC, etc., will function but with degraded performance below VDDMIN. Refer
to Parameter BO10 in Table 24-11 for BOR values.
2008-2014 Microchip Technology Inc.
DS70000318G-page 289
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-5: DC CHARACTERISTICS: OPERATING CURRENT (IDD)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Parameter
Typical(1)
Max
Units
Conditions
No.
Operating Current (IDD)(2)
DC20d
DC20a
DC20b
DC20c
DC21d
DC21a
DC21b
DC21c
DC22d
DC22a
DC22b
DC22c
DC23d
DC23a
DC23b
DC23c
DC24d
DC24a
DC24b
DC24c
DC25d
DC25a
DC25b
DC25c
DC26d
DC26a
DC26b
DC26c
55
55
70
70
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
-40°C
+25°C
+85°C
+125°C
-40°C
10 MIPS
See Note 2
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
55
70
55
70
68
85
68
85
+25°C
+85°C
+125°C
-40°C
16 MIPS
See Note 2 and Note 3
68
85
68
85
78
95
78
95
+25°C
+85°C
+125°C
-40°C
20 MIPS
See Note 2 and Note 3
78
95
78
95
88
110
110
110
110
120
120
120
120
160
150
150
150
140
140
140
140
88
+25°C
+85°C
+125°C
-40°C
30 MIPS
See Note 2 and Note 3
88
88
98
98
+25°C
+85°C
+125°C
-40°C
40 MIPS
See Note 2
98
98
128
125
121
119
115
112
110
108
40 MIPS
+25°C
+85°C
+125°C
-40°C
See Note 2, except PWM is
operating at maximum speed
(PTCON2 = 0x0000)
40 MIPS
+25°C
+85°C
+125°C
See Note 2, except PWM is
operating at 1/2 speed
(PTCON2 = 0x0001)
Note 1: Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
2: IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact
on the current consumption. The test conditions for all IDD measurements are as follows:
• Oscillator is configured in EC mode with PLL, OSC1 is driven with external square wave from
rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
• CLKO is configured as an I/O input pin in the Configuration Word
• All I/O pins are configured as inputs and pulled to VSS
• MCLR = VDD, WDT and FSCM are disabled
• CPU, SRAM, program memory and data memory are operational
• No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are
zeroed)
• CPU executing while(1)statement
• JTAG disabled
3: These parameters are characterized but not tested in manufacturing.
DS70000318G-page 290
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-5: DC CHARACTERISTICS: OPERATING CURRENT (IDD) (CONTINUED)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Parameter
Typical(1)
Max
Units
Conditions
No.
Operating Current (IDD)(2)
DC27d
DC27a
DC27b
DC27c
DC28d
DC28a
DC28b
DC28c
111
108
105
103
102
100
100
100
140
130
130
130
130
120
120
120
mA
mA
mA
mA
mA
mA
mA
mA
-40°C
+25°C
+85°C
+125°C
-40°C
40 MIPS
See Note 2, except PWM is
operating at 1/4 speed
(PTCON2 = 0x0002)
3.3V
3.3V
40 MIPS
+25°C
+85°C
+125°C
See Note 2, except PWM is
operating at 1/8 speed
(PTCON2 = 0x0003)
Note 1: Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
2: IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact
on the current consumption. The test conditions for all IDD measurements are as follows:
• Oscillator is configured in EC mode with PLL, OSC1 is driven with external square wave from
rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
• CLKO is configured as an I/O input pin in the Configuration Word
• All I/O pins are configured as inputs and pulled to VSS
• MCLR = VDD, WDT and FSCM are disabled
• CPU, SRAM, program memory and data memory are operational
• No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are
zeroed)
• CPU executing while(1)statement
• JTAG disabled
3: These parameters are characterized but not tested in manufacturing.
2008-2014 Microchip Technology Inc.
DS70000318G-page 291
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-6: DC CHARACTERISTICS: IDLE CURRENT (IIDLE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Parameter
Typical(1)
Max
Units
Conditions
No.
Idle Current (IIDLE): Core Off Clock On Base Current(2)
DC40d
DC40a
DC40b
DC40c
DC41d
DC41a
DC41b
DC41c
DC42d
DC42a
DC42b
DC42c
DC43d
DC43a
DC43b
DC43c
DC44d
DC44a
DC44b
DC44c
48
48
48
48
60
60
60
60
68
68
68
68
77
77
77
77
86
86
86
86
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
-40°C
+25°C
+85°C
+125°C
-40°C
3.3V
3.3V
3.3V
3.3V
3.3V
10 MIPS
16 MIPS(3)
20 MIPS(3)
30 MIPS(3)
40 MIPS
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
+125°C
Note 1: Data in “Typical” column is at 3.3V, +25°C unless otherwise stated.
2: Base Idle current (IIDLE) is measured as follows:
•
CPU core is off, oscillator is configured in EC mode and external clock is active, OSC1 is driven with
external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
•
•
•
•
CLKO is configured as an I/O input pin in the Configuration Word
All I/O pins are configured as inputs and pulled to VSS
MCLR = VDD, WDT and FSCM are disabled
No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits
are zeroed)
•
JTAG is disabled
3: These parameters are characterized but not tested in manufacturing.
DS70000318G-page 292
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-7: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Parameter
Typical(1)
Max
Units
Conditions
No.
Power-Down Current (IPD)(2,4)
DC60d
DC60a
DC60b
DC60c
DC61d
DC61a
DC61b
DC61c
125
135
235
565
40
500
500
500
950
50
A
A
A
A
A
A
A
A
-40°C
+25°C
+85°C
+125°C
-40°C
3.3V
3.3V
Base Power-Down Current
40
50
+25°C
+85°C
+125°C
(3)
Watchdog Timer Current: IWDT
40
50
80
90
Note 1: Data in the Typical column is at 3.3V, +25°C unless otherwise stated.
2: IPD (Sleep) current is measured as follows:
•
CPU core is off, oscillator is configured in EC mode and external clock active, OSC1 is driven with
external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
•
•
•
•
•
CLKO is configured as an I/O input pin in the Configuration Word
All I/O pins are configured as inputs and pulled to VSS
MCLR = VDD, WDT and FSCM are disabled
All peripheral modules are disabled (PMDx bits are all ones)
The VREGS bit (RCON<8>) = 0(i.e., core regulator is set to stand-by while the device is in
Sleep mode)
•
JTAG disabled
3: The current is the additional current consumed when the WDT module is enabled. This current should
be added to the base IPD current.
4: These currents are measured on the device containing the most memory in this family.
2008-2014 Microchip Technology Inc.
DS70000318G-page 293
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-8: DC CHARACTERISTICS: DOZE CURRENT (IDOZE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Doze
Ratio
Parameter No.
Typical(1)
Max
Units
Conditions
Doze Current (IDOZE)(2)
DC73a
75
60
60
75
60
60
75
60
60
75
60
60
105
105
105
105
105
105
105
105
105
105
105
105
1:2
1:64
1:128
1:2
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
DC73f
-40°C
+25°C
+85°C
+125°C
3.3V
40 MIPS
40 MIPS
40 MIPS
40 MIPS
DC73g
DC70a
DC70f
1:64
1:128
1:2
3.3V
3.3V
3.3V
DC70g
DC71a
DC71f
1:64
1:128
1:2
DC71g
DC72a
DC72f
1:64
1:128
DC72g
Note 1: Data in the Typical column is at 3.3V, +25°C unless otherwise stated.
2: IDOZE is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact
on the current consumption. The test conditions for all IDOZE measurements are as follows:
•
Oscillator is configured in EC mode and external clock active, OSC1 is driven with external square
wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
•
•
•
•
•
CLKO is configured as an I/O input pin in the Configuration Word
All I/O pins are configured as inputs and pulled to VSS
MCLR = VDD, WDT and FSCM are disabled
CPU, SRAM, program memory and data memory are operational
No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits are
zeroed)
•
•
CPU executing while(1)statement
JTAG disabled
DS70000318G-page 294
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristic
Input Low Voltage
Min
Typ(1)
Max
Units
Conditions
VIL
DI10
I/O Pins
VSS
VSS
VSS
VSS
VSS
—
—
—
—
—
0.2 VDD
0.2 VDD
0.2 VDD
0.3 VDD
0.8
V
V
V
V
V
DI15
DI16
DI18
DI19
MCLR
I/O Pins with OSC1
I/O Pins with SDAx, SCLx
I/O Pins with SDAx, SCLx
Input High Voltage
SMBus disabled
SMBus enabled
VIH
DI20
DI21
I/O Pins Not 5V Tolerant(4)
0.7 VDD
0.7 VDD
—
—
VDD
5.5
V
V
I/O Pins 5V Tolerant(4)
DI28
DI29
SDA1, SCL1
SDA1, SCL1
0.7 VDD
2.1
—
—
5.5
5.5
V
V
SMBus disabled
SMBus enabled
ICNPU
IIL
CNx Pull-up Current
DI30
DI50
—
—
250
—
—
A VDD = 3.3V, VPIN = VSS
Input Leakage Current(2,3,4)
I/O Pins with:
4x Driver Pins - RA0-RA2,
RB0-RB2, RB5-RB10, RB15,
RC1, RC2, RC9, RC10
±2
A
A
VSS VPIN VDD,
Pin at high-impedance
8x Driver Pins - RC0, RC3-RC8,
RC11-RC13
—
—
—
—
±4
±8
VSS VPIN VDD,
Pin at high-impedance
16x Driver Pins - RA3, RA4, RB3,
RB4, RB11-RB14
A
A
VSS VPIN VDD,
Pin at high-impedance
DI55
DI56
MCLR
OSC1
—
—
—
—
±2
±2
VSS VPIN VDD
A VSS VPIN VDD,
XT and HS modes
Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltages.
3: Negative current is defined as current sourced by the pin.
4: See “Pin Diagrams” for the list of 5V tolerant I/O pins.
5: VIL source < (VSS – 0.3). Characterized but not tested.
6: Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not
tested.
7: Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.
8: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.
9: Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted pro-
vided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not
exceed the specified limit. Characterized but not tested.
2008-2014 Microchip Technology Inc.
DS70000318G-page 295
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS (CONTINUED)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristic
Min
Typ(1)
Max
Units
Conditions
IICL
Input Low Injection Current
DI60a
0
—
-5(5,8)
mA All pins except VDD, VSS,
AVDD, AVSS, MCLR,
VCAP and RB5
IICH
Input High Injection Current
DI60b
DI60c
0
—
—
+5(6,7,8) mA All pins except VDD, VSS,
AVDD, AVSS, MCLR,
VCAP, RB5 and digital
5V-tolerant designated
pins
IICT
Total Input Injection Current
(sum of all I/O and control pins)
-20(9)
+20(9)
mA Absolute instantaneous
sum of all ± input
injection currents from
all I/O pins
( | IICL + | IICH | ) IICT
Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltages.
3: Negative current is defined as current sourced by the pin.
4: See “Pin Diagrams” for the list of 5V tolerant I/O pins.
5: VIL source < (VSS – 0.3). Characterized but not tested.
6: Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not
tested.
7: Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.
8: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.
9: Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted pro-
vided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not
exceed the specified limit. Characterized but not tested.
DS70000318G-page 296
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-10: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Param. Symbol
Characteristic
Min.
Typ. Max. Units
Conditions
Output Low Voltage
I/O Pins:
4x Sink Driver Pins – RA0-RA2,
RB0-RB2, RB5-RB10, RB15,
RC1, RC2, RC9, RC10
IOL 6 mA, VDD = 3.3V
See Note 1
—
—
0.4
V
Output Low Voltage
I/O Pins:
8x Sink Driver Pins – RC0,
RC3-RC8, RC11-RC13
DO10 VOL
IOL 10 mA, VDD = 3.3V
See Note 1
—
—
—
—
0.4
0.4
V
V
Output Low Voltage
I/O Pins:
16x Sink Driver Pins – RA3,
RA4, RB3, RB4, RB11-RB14
IOL 18 mA, VDD = 3.3V
See Note 1
Output High Voltage
I/O Pins:
4x Source Driver Pins –
RA0-RA2, RB0-RB2, RB5-
RB10, RB15, RC1, RC2, RC9,
RC10
IOH -6 mA, VDD = 3.3V
See Note 1
2.4
—
—
V
Output High Voltage
I/O Pins:
8x Source Driver Pins – RC0,
RC3-RC8, RC11-RC13
DO20 VOH
IOH -10 mA, VDD = 3.3V
See Note 1
2.4
2.4
—
—
—
—
V
V
Output High Voltage
I/O Pins:
16x Source Driver Pins – RA3,
RA4, RB3, RB4, RB11-RB14
IOH -18 mA, VDD = 3.3V
See Note 1
Output High Voltage
I/O Pins:
4x Source Driver Pins –
RA0-RA2, RB0-RB2,
RB5-RB10, RB15, RC1, RC2,
RC9, RC10
IOH -12 mA, VDD = 3.3V
See Note 1
1.5
2.0
3.0
1.5
2.0
3.0
1.5
2.0
3.0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
IOH -11 mA, VDD = 3.3V
See Note 1
V
V
V
IOH -3 mA, VDD = 3.3V
See Note 1
Output High Voltage
8x Source Driver Pins – RC0,
RC3-RC8, RC11-RC13
IOH -16 mA, VDD = 3.3V
See Note 1
IOH -12 mA, VDD = 3.3V
See Note 1
DO20A VOH1
IOH -4 mA, VDD = 3.3V
See Note 1
Output High Voltage
I/O Pins:
16x Source Driver Pins – RA3,
RA4, RB3, RB4, RB11-RB14
IOH -30 mA, VDD = 3.3V
See Note 1
IOH -25 mA, VDD = 3.3V
See Note 1
IOH -8 mA, VDD = 3.3V
See Note 1
Note 1: Parameters are characterized, but not tested.
2008-2014 Microchip Technology Inc.
DS70000318G-page 297
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-11: ELECTRICAL CHARACTERISTICS: BOR
Standard Operating Conditions (see Note 3): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristic
Min(1) Typ
2.55
Max
Units
Conditions
See Note 2
BO10
VBOR
BOR Event on VDD Transition
High-to-Low
—
2.79
V
BOR Event is Tied to VDD Core
Voltage Decrease
Note 1: Parameters are for design guidance only and are not tested in manufacturing.
2: The device will operate as normal until the VDDMIN threshold is reached.
3: Overall functional device operation at VBORMIN < VDD < VDDMIN is tested but not characterized. All device
analog modules such as the ADC, etc., will function but with degraded performance below VDDMIN.
DS70000318G-page 298
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-12: DC CHARACTERISTICS: PROGRAM MEMORY
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
DC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristic
Min Typ(1)
Max
Units
Conditions
Program Flash Memory
Cell Endurance
D130
D131
EP
10,000
VMIN
—
—
—
E/W -40C to +125C
VPR
VDD for Read
3.6
V
VMIN = Minimum operating
voltage
D132B VPEW
VDD for Self-Timed Write
Characteristic Retention
VMIN
20
—
—
10
—
—
—
—
—
—
3.6
—
V
VMIN = Minimum operating
voltage
D134
D135
TRETD
IDDP
Year Provided no other specifications
are violated, -40C to +125C
Supply Current during
Programming
—
—
mA
D136a TRW
D136b TRW
D137a TPE
D137b TPE
D138a TWW
D138b TWW
Row Write Time
1.477
1.435
22.5
21.9
47.4
46
1.538
1.586
23.4
24.2
49.3
50.9
ms TRW = 11064 FRC cycles,
TA = +85°C, See Note 2
Row Write Time
ms TRW = 11064 FRC cycles,
TA = +125°C, See Note 2
Page Erase Time
Page Erase Time
Word Write Cycle Time
Word Write Cycle Time
ms TPE = 168517 FRC cycles,
TA = +85°C, See Note 2
ms TPE = 168517 FRC cycles,
TA = +125°C, See Note 2
µs TWW = 355 FRC cycles,
TA = +85°C, See Note 2
µs TWW = 355 FRC cycles,
TA = +125°C, See Note 2
Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
2: Other conditions: FRC = 7.37 MHz, TUN<5:0> = b'011111(for Min), TUN<5:0> = b'100000(for Max).
This parameter depends on the FRC accuracy (see Table 24-20) and the value of the FRC Oscillator Tun-
ing register (see Register 9-4). For complete details on calculating the Minimum and Maximum time see
Section 5.3 “Programming Operations”.
TABLE 24-13: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS
Operating Conditions: -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristics
Min
Typ
Max
Units
Comments
—
CEFC
External Filter Capacitor
Value(1)
4.7
10
—
F
Capacitor must be low
series resistance
(< 5 ohms)
Note 1: Typical VCAP voltage = 2.5 volts when VDD VDDMIN.
2008-2014 Microchip Technology Inc.
DS70000318G-page 299
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
24.2 AC Characteristics and Timing Parameters
This section defines dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 AC characteristics and timing parameters.
TABLE 24-14: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
AC CHARACTERISTICS
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
Operating voltage VDD range as described in Table 24-1.
FIGURE 24-1:
LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load Condition 1 – for all pins except OSC2
VDD/2
Load Condition 2 – for OSC2
CL
RL
Pin
VSS
CL
Pin
RL = 464
CL = 50 pF for all pins except OSC2
15 pF for OSC2 output
VSS
TABLE 24-15: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS
Param
Symbol
Characteristic
Min
Typ
Max Units
Conditions
No.
DO50 COSCO
OSC2 Pin
—
—
15
pF In XT and HS modes when external
clock is used to drive OSC1
DO56 CIO
DO58 CB
All I/O Pins and OSC2
SCLx, SDAx
—
—
—
—
50
pF EC mode
pF In I2C™ mode
400
DS70000318G-page 300
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-2:
EXTERNAL CLOCK TIMING
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
OSC1
CLKO
OS20
OS30 OS30
OS31 OS31
OS25
OS41
OS40
TABLE 24-16: EXTERNAL CLOCK TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
AC CHARACTERISTICS
Param
Symb
No.
Characteristic
Min
Typ(1)
Max
Units
Conditions
OS10
FIN
External CLKI Frequency
(External clocks allowed only
in EC and ECPLL modes)
DC
—
40
MHz EC
Oscillator Crystal Frequency
3.5
10
—
—
10
40
MHz XT
MHz HS
OS20
OS25
OS30
TOSC
TCY
TOSC = 1/FOSC
Instruction Cycle Time(2)
12.5
25
—
—
—
DC
DC
ns
ns
TosL, External Clock in (OSC1)
TosH High or Low Time
0.375 x TOSC
0.625 x TOSC
ns
EC
EC
OS31
TosR, External Clock in (OSC1)
TosF Rise or Fall Time
—
—
20
ns
OS40
OS41
OS42
TckR CLKO Rise Time(3)
—
—
14
5.2
5.2
16
—
—
18
ns
ns
TckF
GM
CLKO Fall Time(3)
External Oscillator
mA/V VDD = 3.3V,
TA = +25ºC
Transconductance(4)
Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
2: Instruction cycle period (TCY) equals two times the input oscillator time-base period. All specified values
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits may result in an unstable oscillator
operation and/or higher than expected current consumption. All devices are tested to operate at “min.”
values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the
“max.” cycle time limit is “DC” (no clock) for all devices.
3: Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin.
4: Data for this parameter is Preliminary. This parameter is characterized, but not tested in manufacturing.
2008-2014 Microchip Technology Inc.
DS70000318G-page 301
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-17: PLL CLOCK TIMING SPECIFICATIONS (VDD = 3.0V TO 3.6V)
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC CHARACTERISTICS
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
Param
Symbol
No.
Characteristic
Min
Typ(1)
Max
Units
Conditions
OS50
FPLLI
PLL Voltage Controlled
Oscillator (VCO) Input
Frequency Range
0.8
—
8
MHz ECPLL, XTPLL modes
OS51
FSYS
On-Chip VCO System
Frequency
100
—
200
MHz
mS
OS52
OS53
TLOCK
DCLK
PLL Start-up Time (Lock Time)
CLKO Stability (Jitter)(2)
0.9
-3
1.5
0.5
3.1
3
%
Measured over 100 ms
period
Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only
and are not tested in manufacturing.
2: These parameters are characterized by similarity, but are not tested in manufacturing. This specification is
based on clock cycle by clock cycle measurements. To calculate the effective jitter for individual time bases
or communication clocks use this formula:
DCLK
Peripheral Clock Jitter = -----------------------------------------------------------------------
FOSC
-------------------------------------------------------------
Peripheral Bit Rate Clock
For example: FOSC = 32 MHz, DCLK = 3%, SPI bit rate clock (i.e., SCKx) is 2 MHz.
DCLK
3%
3%
-------
-----------------------------
---------
SPI SCK Jitter =
=
=
= 0.75%
4
16
32 MHz
--------------------
2 MHz
TABLE 24-18: AUXILIARY PLL CLOCK TIMING SPECIFICATIONS (VDD = 3.0V TO 3.6V)
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC CHARACTERISTICS
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
Param
Symbol
No.
Characteristic
Min
Typ(1)
Max
Units
Conditions
OS56
OS57
OS58
FHPOUT On-Chip 16x PLL CCO
Frequency
112
118
120
MHz
FHPIN
On-Chip 16x PLL Phase
Detector Input Frequency
7.0
—
7.37
—
7.5
10
MHz
µs
TSU
Frequency Generator Lock
Time
Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only
and are not tested in manufacturing.
DS70000318G-page 302
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-19: AC CHARACTERISTICS: INTERNAL FRC ACCURACY
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC CHARACTERISTICS
Operating temperature
-40°C TA +85°C for industrial
-40°C TA +125°C for Extended
Param
Characteristic
Min
Typ
Max
Units
Conditions
No.
Internal FRC Accuracy @ FRC Frequency = 7.37 MHz(1)
F20a
F20b
FRC
FRC
-2
-5
—
—
+2
+5
%
%
-40°C TA +85°C
-40°C TA +125°C
VDD = 3.0-3.6V
VDD = 3.0-3.6V
Note 1: Frequency calibrated at +25°C and 3.3V. TUNx bits can be used to compensate for temperature drift.
TABLE 24-20: AC CHARACTERISTICS: INTERNAL LPRC ACCURACY
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC CHARACTERISTICS
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
Param
No.
Characteristic
Min
Typ
Max
Units
Conditions
LPRC @ 32.768 kHz(1)
F21a LPRC
-20
-70
±6
—
+20
+70
%
%
-40°C TA +85°C
-40°C TA +125°C
VDD = 3.0-3.6V
VDD = 3.0-3.6V
F21b LPRC
Note 1: Change of LPRC frequency as VDD changes.
2008-2014 Microchip Technology Inc.
DS70000318G-page 303
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-3:
I/O TIMING CHARACTERISTICS
I/O Pin
(Input)
DI35
DI40
I/O Pin
(Output)
New Value
Old Value
DO31
DO32
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-21: I/O TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min
Typ(1)
Max Units
Conditions
DO31
TIOR
Port Output Rise Time:
4x Source Driver Pins – RA0-RA2,
RB0-RB2, RB5-RB10, RB15, RC1,
RC2, RC9, RC10
—
10
25
ns
Refer to Figure 24-1
for test conditions
8x Source Driver Pins – RC0,
RC3-RC8, RC11-RC13
—
—
8
6
20
15
ns
ns
16x Source Driver Pins – RA3,
RA4, RB3, RB4, RB11-RB14
DO32
TIOF
Port Output Fall Time:
4x Source Driver Pins – RA0-RA2,
RB0-RB2, RB5-RB10, RB15, RC1,
RC2, RC9, RC10
Refer to Figure 24-1
for test conditions
—
10
25
ns
8x Source Driver Pins – RC0,
RC3-RC8, RC11-RC13
—
—
8
6
20
15
ns
ns
16x Source Driver Pins – RA3,
RA4, RB3, RB4, RB11-RB14
DI35
DI40
TINP
INTx Pin High or Low Time (input)
CNx High or Low Time (input)
20
2
—
—
—
—
ns
TRBP
TCY
Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
DS70000318G-page 304
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-4:
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING CHARACTERISTICS
VDD
SY12
MCLR
SY10
Internal
POR
SY11
PWRT
Time-out
SY30
OSC
Time-out
Internal
Reset
Watchdog
Timer
Reset
SY20
SY13
SY13
I/O Pins
SY35
FSCM
Delay
Note: Refer to Figure 24-1 for load conditions.
2008-2014 Microchip Technology Inc.
DS70000318G-page 305
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-22: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER
TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristic(1)
Min
Typ(2)
Max Units
Conditions
SY10 TMCL
MCLR Pulse Width (low)
2
—
—
—
s
-40°C to +85°C
SY11 TPWRT Power-up Timer Period
—
2
4
ms -40°C to +85°C,
User programmable
8
16
32
64
128
SY12 TPOR
SY13 TIOZ
Power-on Reset Delay
3
10
30
s
s
-40°C to +85°C
I/O High-Impedance from MCLR 0.68
Low or Watchdog Timer Reset
0.72
1.2
SY20 TWDT1 Watchdog Timer Time-out Period
—
—
—
ms See Section 21.4 “Watch-
dog Timer (WDT)” and
LPRC Parameter F21a
(Table 24-20)
SY30 TOST
Oscillator Start-up Time
—
1024 TOSC
—
—
TOSC = OSC1 period
Note 1: These parameters are characterized but not tested in manufacturing.
2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
DS70000318G-page 306
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-5:
TIMER1, 2 AND 3 EXTERNAL CLOCK TIMING CHARACTERISTICS
TxCK
Tx11
Tx10
Tx15
Tx20
OS60
TMRx
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-23: TIMER1 EXTERNAL CLOCK TIMING REQUIREMENTS(1)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min.
Typ.
Max.
Units
Conditions
TA10 TTXH
TA11 TTXL
TA15 TTXP
T1CK High
Time
Synchronous,
no prescaler
TCY + 20
—
—
ns Must also meet
Parameter TA15,
N = Prescale value
Synchronous, (TCY + 20)/N
with prescaler
—
—
ns
(1, 8, 64, 256)
ns
Asynchronous
20
—
—
—
—
T1CK Low
Time
Synchronous,
no prescaler
TCY + 20
ns Must also meet
Parameter TA15,
N = Prescale value
(1, 8, 64, 256)
Synchronous, (TCY + 20)/N
with prescaler
—
—
ns
Asynchronous
20
—
—
—
—
ns
ns
T1CK Input
Period
Synchronous,
no prescaler
2 TCY + 40
Synchronous,
with prescaler
Greater of:
40 ns or
—
—
—
N = Prescale value
(1, 8, 64, 256)
(2 TCY + 40)/N
Asynchronous
40
—
—
—
ns
OS60 FT1
T1CK Oscillator Input
Frequency Range (oscillator
enabled by setting bit, TCS
(T1CON<1>))
DC
50
kHz
TA20 TCKEXTMRL Delay from External T1CK
Clock Edge to Timer Increment
0.75 TCY + 40
—
1.75 TCY + 40
—
Note 1: Timer1 is a Type A timer.
2008-2014 Microchip Technology Inc.
DS70000318G-page 307
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-24: TIMER2 EXTERNAL CLOCK TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristic
Min.
Typ.
Max.
Units
Conditions
TB10
TTXH
T2CK High Synchronous
Time
Greater of:
20 ns or
(TCY + 20)/N
—
—
ns
Must also meet
Parameter TB15,
N = Prescale value
(1, 8, 64, 256)
TB11
TTXL
TTXP
T2CK Low Synchronous
Time
Greater of:
20 ns or
(TCY + 20)/N
—
—
ns
Must also meet
Parameter TB15,
N = Prescale value
(1, 8, 64, 256)
TB15
TB20
T2CK Input Synchronous
Period
Greater of:
40 ns or
(2 TCY + 40)/N
—
—
—
ns
ns
N = Prescale value
(1, 8, 64, 256)
TCKEXTMRL Delay from External T2CK 0.75 TCY + 40
1.75 TCY + 40
Clock Edge to Timer
Increment
TABLE 24-25: TIMER3 EXTERNAL CLOCK TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min
Typ
Max
Units
Conditions
TC10
TC11
TC15
TTXH
TTXL
TTXP
T3CK High Synchronous
Time
TCY + 20
—
—
ns
Must also meet
Parameter TC15
T3CK Low Synchronous
Time
TCY + 20
—
—
—
—
—
ns
ns
—
Must also meet
Parameter TC15
T3CK Input Synchronous,
2 TCY + 40
Period
with prescaler
TC20 TCKEXTMRL Delay from External T3CK 0.75 TCY + 40
1.75 TCY + 40
Clock Edge to Timer
Increment
DS70000318G-page 308
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-6:
INPUT CAPTURE x (ICx) TIMING CHARACTERISTICS
ICx
IC11
IC10
IC15
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-26: INPUT CAPTURE x TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic(1)
Min
Max
Units
Conditions
IC10
IC11
IC15
TccL
TccH
TccP
ICx Input Low Time No prescaler
With prescaler
0.5 TCY + 20
10
—
—
—
—
—
ns
ns
ns
ns
ns
ICx Input High Time No prescaler
With prescaler
0.5 TCY + 20
10
ICx Input Period
(TCY + 40)/N
N = Prescale
value (1, 4, 16)
Note 1: These parameters are characterized but not tested in manufacturing.
FIGURE 24-7:
OUTPUT COMPARE x MODULE (OCx) TIMING CHARACTERISTICS
OCx
(Output Compare
or PWM Mode)
OC11
OC10
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-27: OUTPUT COMPARE x MODULE TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic(1)
Min
Typ
Max
Units
Conditions
OC10 TccF
OC11 TccR
OCx Output Fall Time
OCx Output Rise Time
—
—
—
—
—
—
ns
ns
See Parameter DO32
See Parameter DO31
Note 1: These parameters are characterized but not tested in manufacturing.
2008-2014 Microchip Technology Inc.
DS70000318G-page 309
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-8:
OCx/PWMx MODULE TIMING CHARACTERISTICS
OC20
OCFA
OCx
OC15
Active
Tri-State
TABLE 24-28: SIMPLE OCx/PWMx MODE TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic(1)
Min
Typ
Max
Units
Conditions
OC15
TFD
Fault Input to PWMx I/O
Change
—
—
TCY + 20
ns
OC20
TFLT
Fault Input Pulse Width
TCY + 20
—
—
ns
Note 1: These parameters are characterized but not tested in manufacturing.
DS70000318G-page 310
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-9:
HIGH-SPEED PWMx MODULE FAULT TIMING CHARACTERISTICS
MP30
FLTx
MP20
PWMx
FIGURE 24-10:
HIGH-SPEED PWMx MODULE TIMING CHARACTERISTICS
MP11 MP10
PWMx
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-29: HIGH-SPEED PWMx MODULE TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic(1)
Min
Typ
Max
Units
Conditions
MP10
MP11
MP20
TFPWM
TRPWM
TFD
PWMx Output Fall Time
PWMx Output Rise Time
—
—
—
2.5
2.5
—
—
—
15
ns
ns
ns
Fault Input to PWM
I/O Change
MP30
TFH
Minimum PWMx Fault Pulse
Width
8
—
—
ns
ns
DTC<1:0> = 10
ACLK = 120 MHz
MP31
MP32
TPDLY
ACLK
Tap Delay
1.04
—
—
—
—
PWMx Input Clock
120
MHz See Note 2
Note 1: These parameters are characterized but not tested in manufacturing.
2: This parameter is a maximum allowed input clock for the PWMx module.
2008-2014 Microchip Technology Inc.
DS70000318G-page 311
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-30: SPIx MAXIMUM DATA/CLOCK RATE SUMMARY
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Master
Transmit Only
(Half-Duplex)
Master
Slave
Maximum
Data Rate
Transmit/Receive Transmit/Receive
(Full-Duplex)
CKE
CKP
SMP
(Full-Duplex)
15 MHz
9 MHz
Table 24-31
—
—
0,1
1
0,1
0,1
0,1
0
0,1
1
—
—
—
—
—
—
Table 24-32
—
9 MHz
Table 24-33
—
0
1
15 MHz
11 MHz
15 MHz
11 MHz
—
—
—
—
Table 24-34
Table 24-35
Table 24-36
Table 24-37
1
0
1
1
0
0
1
0
0
0
0
FIGURE 24-11:
SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY, CKE = 0) TIMING
CHARACTERISTICS
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
Bit 14 - - - - - -1
MSb
LSb
SDOx
SP30, SP31
Note: Refer to Figure 24-1 for load conditions.
SP30, SP31
FIGURE 24-12:
SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY, CKE = 1) TIMING
CHARACTERISTICS
SP36
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
Bit 14 - - - - - -1
SP30, SP31
Note: Refer to Figure 24-1 for load conditions.
MSb
LSb
SDOx
DS70000318G-page 312
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-31: SPIx MASTER MODE (HALF-DUPLEX, TRANSMIT ONLY) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
TscP
Characteristic(1)
Min
Typ(2)
Max
Units
Conditions
SP10
SP20
Maximum SCKx Frequency
SCKx Output Fall Time
—
—
—
—
15
—
MHz See Note 3
TscF
TscR
TdoF
TdoR
ns
ns
ns
ns
ns
ns
See Parameter DO32
and Note 4
SP21
SP30
SP31
SP35
SP36
SCKx Output Rise Time
—
—
—
—
30
—
—
—
6
—
—
—
20
—
See Parameter DO31
and Note 4
SDOx Data Output Fall Time
SDOx Data Output Rise Time
See Parameter DO32
and Note 4
See Parameter DO31
and Note 4
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
TdiV2scH, SDOx Data Output Setup to
—
TdiV2scL
First SCKx Edge
Note 1: These parameters are characterized, but are not tested in manufacturing.
2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
3: The minimum clock period for SCKx is 66.7 ns. Therefore, the clock generated in Master mode must not
violate this specification.
4: Assumes 50 pF load on all SPIx pins.
2008-2014 Microchip Technology Inc.
DS70000318G-page 313
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-13:
SPIx MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1) TIMING
CHARACTERISTICS
SP36
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
Bit 14 - - - - - -1
MSb
LSb
SDOx
SDIx
SP30, SP31
SP40
MSb In
SP41
LSb In
Bit 14 - - - -1
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-32: SPIx MASTER MODE (FULL-DUPLEX, CKE = 1, CKP = x, SMP = 1) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
TscP
Characteristic(1)
Min
Typ(2)
Max
Units
Conditions
SP10
SP20
Maximum SCKx Frequency
SCKx Output Fall Time
—
—
—
—
9
MHz See Note 3
TscF
TscR
TdoF
TdoR
—
ns
ns
ns
ns
ns
ns
ns
ns
See Parameter DO32
and Note 4
SP21
SP30
SP31
SP35
SP36
SP40
SP41
SCKx Output Rise Time
—
—
—
—
30
30
30
—
—
—
6
—
—
—
20
—
—
—
See Parameter DO31
and Note 4
SDOx Data Output Fall Time
SDOx Data Output Rise Time
See Parameter DO32
and Note 4
See Parameter DO31
and Note 4
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
TdoV2sc, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
—
—
—
TdiV2scH, Setup Time of SDIx Data
TdiV2scL Input to SCKx Edge
TscH2diL, Hold Time of SDIx Data Input
TscL2diL
to SCKx Edge
Note 1: These parameters are characterized, but are not tested in manufacturing.
2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
3: The minimum clock period for SCKx is 111 ns. The clock generated in Master mode must not violate this
specification.
4: Assumes 50 pF load on all SPIx pins.
DS70000318G-page 314
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-14:
SPIx MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 1) TIMING
CHARACTERISTICS
SCKx
(CKP = 0)
SP10
SP21
SP20
SP20
SP21
SCKx
(CKP = 1)
SP35
Bit 14 - - - - - -1
SP30, SP31
LSb In
MSb
LSb
SDOx
SDIx
SP30, SP31
MSb In
SP40 SP41
Bit 14 - - - -1
Note: Refer to Figure 24-1 for load conditions.
TABLE 24-33: SPIx MASTER MODE (FULL-DUPLEX, CKE = 0, CKP = x, SMP = 1) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
TscP
Characteristic(1)
Min
Typ(2)
Max
Units
Conditions
SP10
Maximum SCKx Frequency
—
—
9
MHz -40ºC to +125ºC and
see Note 3
SP20
SP21
SP30
SP31
SP35
SP36
SP40
SP41
TscF
TscR
TdoF
TdoR
SCKx Output Fall Time
—
—
—
—
—
30
30
30
—
—
—
—
6
—
—
—
—
20
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
See Parameter DO32
and Note 4
SCKx Output Rise Time
SDOx Data Output Fall Time
SDOx Data Output Rise Time
See Parameter DO31
and Note 4
See Parameter DO32
and Note 4
See Parameter DO31
and Note 4
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
—
—
—
TdiV2scH, Setup Time of SDIx Data
TdiV2scL Input to SCKx Edge
TscH2diL, Hold Time of SDIx Data Input
TscL2diL
to SCKx Edge
Note 1: These parameters are characterized, but are not tested in manufacturing.
2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
3: The minimum clock period for SCKx is 111 ns. The clock generated in Master mode must not violate this
specification.
4: Assumes 50 pF load on all SPIx pins.
2008-2014 Microchip Technology Inc.
DS70000318G-page 315
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-15:
SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING
CHARACTERISTICS
SP60
SSx
SP52
SP50
SCKx
(CKP = 0)
SP70
SP72
SP73
SCKx
(CKP = 1)
SP35
SP73
SP72
LSb
MSb
Bit 14 - - - - - -1
SDOx
SDIx
SP30, SP31
Bit 14 - - - -1
SP51
MSb In
SP41
LSb In
SP40
Note: Refer to Figure 24-1 for load conditions.
DS70000318G-page 316
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-34: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 0, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
TscP
Characteristic(1)
Min
Typ(2) Max Units
Conditions
SP70
Maximum SCKx Input
Frequency
—
—
—
—
—
—
6
15
—
—
—
—
20
—
—
—
—
50
—
50
MHz See Note 3
SP72
SP73
SP30
SP31
SP35
SP36
SP40
SP41
SP50
SP51
SP52
SP60
TscF
TscR
TdoF
TdoR
SCKx Input Fall Time
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
See Parameter DO32
and Note 4
SCKx Input Rise Time
—
See Parameter DO31
and Note 4
SDOx Data Output Fall Time
SDOx Data Output Rise Time
—
See Parameter DO32
and Note 4
—
See Parameter DO31
and Note 4
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
30
—
—
—
—
—
—
—
TdiV2scH, Setup Time of SDIx Data Input
30
TdiV2scL
TscH2diL, Hold Time of SDIx Data Input
TscL2diL to SCKx Edge
to SCKx Edge
30
TssL2scH, SSx to SCKx or SCKx Input
TssL2scL
120
TssH2doZ SSx to SDOx Output
10
1.5 TCY + 40
—
High-Impedance(4)
TscH2ssH SSx after SCKx Edge
TscL2ssH
See Note 4
TssL2doV SDOx Data Output Valid after
SSx Edge
Note 1: These parameters are characterized, but are not tested in manufacturing.
2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
3: The minimum clock period for SCKx is 66.7 ns. Therefore, the SCKx clock generated by the Master must
not violate this specification.
4: Assumes 50 pF load on all SPIx pins.
2008-2014 Microchip Technology Inc.
DS70000318G-page 317
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-16:
SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING
CHARACTERISTICS
SP60
SSx
SP52
SP50
SCKx
(CKP = 0)
SP70
SP72
SP73
SP72
SCKx
(CKP = 1)
SP35
SP73
SP52
MSb
Bit 14 - - - - - -1
LSb
SDOx
SDIx
SP30, SP31
Bit 14 - - - -1
SP51
MSb In
SP41
LSb In
SP40
Note: Refer to Figure 24-1 for load conditions.
DS70000318G-page 318
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-35: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 1, CKP = 1, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
TscP
Characteristic(1)
Min
Typ(2) Max Units
Conditions
SP70
Maximum SCKx Input
Frequency
—
—
—
—
—
—
6
11
—
—
—
—
20
—
—
—
—
50
—
50
MHz See Note 3
SP72
SP73
SP30
SP31
SP35
SP36
SP40
SP41
SP50
SP51
SP52
SP60
TscF
TscR
TdoF
TdoR
SCKx Input Fall Time
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
See Parameter DO32
and Note 4
SCKx Input Rise Time
—
See Parameter DO31
and Note 4
SDOx Data Output Fall Time
SDOx Data Output Rise Time
—
See Parameter DO32
and Note 4
—
See Parameter DO31
and Note 4
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
30
—
—
—
—
—
—
—
TdiV2scH, Setup Time of SDIx Data Input
30
TdiV2scL
TscH2diL, Hold Time of SDIx Data Input
TscL2diL to SCKx Edge
to SCKx Edge
30
TssL2scH, SSx to SCKx or SCKx Input
TssL2scL
120
TssH2doZ SSx to SDOx Output
10
1.5 TCY + 40
—
High-Impedance(4)
TscH2ssH SSx after SCKx Edge
TscL2ssH
See Note 4
TssL2doV SDOx Data Output Valid after
SSx Edge
Note 1: These parameters are characterized, but are not tested in manufacturing.
2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
3: The minimum clock period for SCKx is 91 ns. Therefore, the SCKx clock generated by the Master must not
violate this specification.
4: Assumes 50 pF load on all SPIx pins.
2008-2014 Microchip Technology Inc.
DS70000318G-page 319
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-17:
SPIx SLAVE MODE (FULL-DUPLEX CKE = 0, CKP = 1, SMP = 0) TIMING
CHARACTERISTICS
SSX
SP52
SP50
SCKX
(CKP = 0)
SP70
SP72
SP73
SP73
SP72
SCKX
(CKP = 1)
SP35
SDOX
SDIX
MSb
Bit 14 - - - - - -1
LSb
SP51
SP30, SP31
Bit 14 - - - -1
MSb In
SP41
SP40
LSb In
Note: Refer to Figure 24-1 for load conditions.
DS70000318G-page 320
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-36: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 1, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
TscP
Characteristic(1)
Min
Typ(2) Max Units
Conditions
SP70
Maximum SCKx Input
Frequency
—
—
—
—
—
—
6
15
—
—
—
—
20
—
—
—
—
50
—
MHz See Note 3
SP72
SP73
SP30
SP31
SP35
SP36
SP40
SP41
SP50
SP51
SP52
TscF
TscR
TdoF
TdoR
SCKx Input Fall Time
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
See Parameter DO32
and Note 4
SCKx Input Rise Time
—
See Parameter DO31
and Note 4
SDOx Data Output Fall Time
SDOx Data Output Rise Time
—
See Parameter DO32
and Note 4
—
See Parameter DO31
and Note 4
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
30
—
—
—
—
—
—
TdiV2scH, Setup Time of SDIx Data Input
30
TdiV2scL
TscH2diL, Hold Time of SDIx Data Input
TscL2diL to SCKx Edge
to SCKx Edge
30
120
TssL2scH, SSx to SCKx or SCKx Input
TssL2scL
TssH2doZ SSx to SDOx Output
10
See Note 4
See Note 4
High-Impedance
TscH2ssH SSx after SCKx Edge
TscL2ssH
1.5 TCY + 40
Note 1: These parameters are characterized, but are not tested in manufacturing.
2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
3: The minimum clock period for SCKx is 66.7 ns. Therefore, the SCKx clock generated by the Master must
not violate this specification.
4: Assumes 50 pF load on all SPIx pins.
2008-2014 Microchip Technology Inc.
DS70000318G-page 321
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-18:
SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING
CHARACTERISTICS
SSX
SP52
SP50
SCKX
(CKP = 0)
SP70
SP72
SP73
SP73
SP72
SCKX
(CKP = 1)
SP35
SDOx
SDIx
MSb
Bit 14 - - - - - -1
LSb
SP51
SP30, SP31
Bit 14 - - - -1
MSb In
SP41
LSb In
SP40
Note: Refer to Figure 24-1 for load conditions.
DS70000318G-page 322
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-37: SPIx SLAVE MODE (FULL-DUPLEX, CKE = 0, CKP = 0, SMP = 0) TIMING
REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
TscP
Characteristic(1)
Min
Typ(2) Max Units
Conditions
SP70
Maximum SCKx Input
Frequency
—
—
—
—
—
—
6
11
—
—
—
—
20
—
—
—
—
50
—
MHz See Note 3
SP72
SP73
SP30
SP31
SP35
SP36
SP40
SP41
SP50
SP51
SP52
TscF
TscR
TdoF
TdoR
SCKx Input Fall Time
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
See Parameter DO32
and Note 4
SCKx Input Rise Time
—
See Parameter DO31
and Note 4
SDOx Data Output Fall Time
SDOx Data Output Rise Time
—
See Parameter DO32
and Note 4
—
See Parameter DO31
and Note 4
TscH2doV, SDOx Data Output Valid after
TscL2doV SCKx Edge
—
TdoV2scH, SDOx Data Output Setup to
TdoV2scL First SCKx Edge
30
—
—
—
—
—
—
TdiV2scH, Setup Time of SDIx Data Input
30
TdiV2scL
TscH2diL, Hold Time of SDIx Data Input
TscL2diL to SCKx Edge
to SCKx Edge
30
120
TssL2scH, SSx to SCKx or SCKx Input
TssL2scL
TssH2doZ SSx to SDOx Output
10
See Note 4
See Note 4
High-Impedance
TscH2ssH SSx after SCKx Edge
TscL2ssH
1.5 TCY + 40
Note 1: These parameters are characterized, but are not tested in manufacturing.
2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
3: The minimum clock period for SCKx is 91 ns. Therefore, the SCKx clock generated by the Master must not
violate this specification.
4: Assumes 50 pF load on all SPIx pins.
2008-2014 Microchip Technology Inc.
DS70000318G-page 323
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-19:
I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (MASTER MODE)
SCLx
IM31
IM34
IM30
IM33
SDAx
Start
Condition
Stop
Condition
Note: Refer to Figure 24-1 for load conditions.
FIGURE 24-20:
I2Cx BUS DATA TIMING CHARACTERISTICS (MASTER MODE)
IM20
IM21
IM11
IM10
SCLx
IM11
IM26
IM10
IM33
IM25
SDAx
In
IM45
IM40
IM40
SDAx
Out
Note: Refer to Figure 24-1 for load conditions.
DS70000318G-page 324
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-38: I2Cx BUS DATA TIMING REQUIREMENTS (MASTER MODE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristic
Min(1)
Max
Units
Conditions
IM10
TLO:SCL Clock Low Time 100 kHz mode TCY/2 (BRG + 1)
400 kHz mode TCY/2 (BRG + 1)
—
—
s
s
s
s
s
s
ns
ns
ns
ns
ns
ns
ns
ns
ns
s
s
s
s
s
s
s
s
s
s
s
s
ns
ns
ns
ns
ns
ns
s
s
s
pF
ns
1 MHz mode(2) TCY/2 (BRG + 1)
—
IM11
IM20
IM21
IM25
IM26
IM30
IM31
IM33
IM34
IM40
IM45
THI:SCL Clock High Time 100 kHz mode TCY/2 (BRG + 1)
—
400 kHz mode TCY/2 (BRG + 1)
1 MHz mode(2) TCY/2 (BRG + 1)
—
—
TF:SCL
TR:SCL
SDAx and SCLx 100 kHz mode
—
300
300
100
1000
300
300
—
CB is specified to be
from 10 pF to 400 pF
Fall Time
400 kHz mode
20 + 0.1 CB
1 MHz mode(2)
—
SDAx and SCLx 100 kHz mode
—
CB is specified to be
from 10 pF to 400 pF
Rise Time
400 kHz mode
20 + 0.1 CB
1 MHz mode(2)
—
250
100
40
0
TSU:DAT Data Input
Setup Time
100 kHz mode
400 kHz mode
1 MHz mode(2)
100 kHz mode
400 kHz mode
1 MHz mode(2)
—
—
THD:DAT Data Input
Hold Time
—
0
0.9
—
0.2
TSU:STA Start Condition 100 kHz mode TCY/2 (BRG + 1)
—
Only relevant for
Repeated Start
condition
Setup Time
400 kHz mode TCY/2 (BRG + 1)
—
1 MHz mode(2) TCY/2 (BRG + 1)
—
THD:STA Start Condition 100 kHz mode TCY/2 (BRG + 1)
—
After this period the
first clock pulse is
generated
Hold Time
400 kHz mode TCY/2 (BRG + 1)
—
1 MHz mode(2) TCY/2 (BRG + 1)
—
TSU:STO Stop Condition 100 kHz mode TCY/2 (BRG + 1)
—
Setup Time
400 kHz mode TCY/2 (BRG + 1)
—
1 MHz mode(2) TCY/2 (BRG + 1)
—
THD:STO Stop Condition
Hold Time
100 kHz mode TCY/2 (BRG + 1)
400 kHz mode TCY/2 (BRG + 1)
1 MHz mode(2) TCY/2 (BRG + 1)
—
—
—
TAA:SCL Output Valid
From Clock
100 kHz mode
400 kHz mode
1 MHz mode(2)
—
—
3500
1000
400
—
—
TBF:SDA Bus Free Time 100 kHz mode
4.7
1.3
0.5
—
Time the bus must be
free before a new
transmission can start
400 kHz mode
1 MHz mode(2)
—
—
IM50
IM51
CB
Bus Capacitive Loading
Pulse Gobbler Delay
400
390
TPGD
65
See Note 3
Note 1: BRG is the value of the I2C™ Baud Rate Generator. Refer to “Inter-Integrated Circuit (I2C™)”
(DS70000195) in the “dsPIC33/PIC24 Family Reference Manual”.
2: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).
3: Typical value for this parameter is 130 ns.
2008-2014 Microchip Technology Inc.
DS70000318G-page 325
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
FIGURE 24-21:
I2Cx BUS START/STOP BITS TIMING CHARACTERISTICS (SLAVE MODE)
SCLx
IS34
IS31
IS30
IS33
SDAx
Start
Condition
Stop
Condition
FIGURE 24-22:
I2Cx BUS DATA TIMING CHARACTERISTICS (SLAVE MODE)
IS20
IS21
IS11
IS10
SCLx
IS30
IS26
IS31
IS33
IS25
SDAx
In
IS45
IS40
IS40
SDAx
Out
DS70000318G-page 326
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-39: I2Cx BUS DATA TIMING REQUIREMENTS (SLAVE MODE)
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param. Symbol
Characteristic
Min
Max
Units
Conditions
IS10
TLO:SCL Clock Low Time 100 kHz mode
4.7
—
s
Device must operate at a
minimum of 1.5 MHz
400 kHz mode
1.3
—
s
Device must operate at a
minimum of 10 MHz
1 MHz mode(1)
0.5
4.0
—
—
s
s
IS11
THI:SCL Clock High Time 100 kHz mode
Device must operate at a
minimum of 1.5 MHz
400 kHz mode
1 MHz mode(1)
0.6
—
s
Device must operate at a
minimum of 10 MHz
0.5
—
300
300
100
1000
300
300
—
s
ns
ns
ns
ns
ns
ns
ns
ns
ns
s
s
s
s
s
s
s
s
s
s
s
s
ns
ns
ns
ns
ns
ns
s
s
s
pF
IS20
IS21
IS25
IS26
IS30
IS31
IS33
IS34
IS40
IS45
IS50
TF:SCL
TR:SCL
SDAx and SCLx 100 kHz mode
—
CB is specified to be from
10 pF to 400 pF
Fall Time
400 kHz mode
1 MHz mode(1)
20 + 0.1 CB
—
—
SDAx and SCLx 100 kHz mode
CB is specified to be from
10 pF to 400 pF
Rise Time
400 kHz mode
1 MHz mode(1)
20 + 0.1 CB
—
TSU:DAT Data Input
Setup Time
100 kHz mode
400 kHz mode
1 MHz mode(1)
100 kHz mode
400 kHz mode
1 MHz mode(1)
100 kHz mode
400 kHz mode
1 MHz mode(1)
100 kHz mode
400 kHz mode
1 MHz mode(1)
100 kHz mode
400 kHz mode
1 MHz mode(1)
100 kHz mode
400 kHz mode
1 MHz mode(1)
100 kHz mode
400 kHz mode
1 MHz mode(1)
100 kHz mode
400 kHz mode
1 MHz mode(1)
250
100
100
0
—
—
THD:DAT Data Input
Hold Time
—
0
0.9
0.3
—
0
TSU:STA Start Condition
Setup Time
4.7
0.6
0.25
4.0
0.6
0.25
4.7
0.6
0.6
4000
600
250
0
Only relevant for Repeated
Start condition
—
—
THD:STA Start Condition
Hold Time
—
After this period, the first
clock pulse is generated
—
—
TSU:STO Stop Condition
Setup Time
—
—
—
THD:STO Stop Condition
Hold Time
—
—
—
TAA:SCL Output Valid
From Clock
3500
1000
350
—
0
0
TBF:SDA Bus Free Time
4.7
1.3
0.5
—
Time the bus must be free
before a new transmission
can start
—
—
CB
Bus Capacitive Loading
400
Note 1: Maximum pin capacitance = 10 pF for all I2Cx pins (for 1 MHz mode only).
2008-2014 Microchip Technology Inc.
DS70000318G-page 327
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
=
TABLE 24-40: 10-BIT HIGH-SPEED ADC MODULE SPECIFICATIONS
Standard Operating Conditions (see Note 2): 3.0V and 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristic
Module VDD Supply
Module VSS Supply
Min.
Typ.
Max. Units
Conditions
Device Supply
AD01 AVDD
AD02 AVSS
—
—
—
—
—
—
—
—
AVDD is internally connected to
VDD; see Parameter DC10 in
Table 24-4
AVSS is internally connected
to VSS
Analog Input
AD10 VINH-VINL Full-Scale Input Span
VSS
AVSS
—
—
VDD
AVDD
—
V
V
AD11 VIN
AD12 IAD
AD13
Absolute Input Voltage
Operating Current
Leakage Current
—
8
mA
—
—
±0.6
—
A VINL = AVSS = 0V, AVDD = 3.3V,
Source Impedance = 100
AD17 RIN
Recommended Impedance
Of Analog Voltage Source
—
—
100
DC Accuracy @ 1.5 Msps
AD20A Nr
Resolution
10 Data Bits
AD21A INL
Integral Nonlinearity
Differential Nonlinearity
Gain Error
-0.5 -0.3/+0.5 +1.2
LSb
LSb
LSb
LSb
AD22A DNL
AD23A GERR
AD24A EOFF
-0.9
13
6
±0.6
15
7
+0.9
22
8
Offset Error
Monotonicity(1)
AD25A
—
—
—
—
—
Guaranteed
Guaranteed
Guaranteed
DC Accuracy @ 1.7 Msps
AD20B Nr
Resolution
10 Data Bits
AD21B INL
Integral Nonlinearity
Differential Nonlinearity
Gain Error
-0.5 -0.4/+1.1 +1.8
LSb
LSb
LSb
LSb
—
AD22B DNL
AD23B GERR
AD24B EOFF
-1.0
13
6
±1.0
15
7
+1.5
22
8
Offset Error
Monotonicity(1)
AD25B
—
—
—
—
DC Accuracy @ 2.0 Msps
AD20C Nr
Resolution
10 Data Bits
-0.8 -0.5/+1.8 +2.8
-1.0 -1.0/+1.8 +2.8
AD21C INL
Integral Nonlinearity
Differential Nonlinearity
Gain Error
LSb
LSb
LSb
LSb
—
AD22C DNL
AD23C GERR
AD24C EOFF
14
6
16
7
23
8
Offset Error
Monotonicity(1)
AD25C
—
—
—
—
Dynamic Performance
AD30 THD
AD31 SINAD
AD32 SFDR
AD33 FNYQ
AD34 ENOB
Total Harmonic Distortion
Signal to Noise and Distortion
Spurious Free Dynamic Range
Input Signal Bandwidth
—
—
—
—
—
-73
58
—
—
—
1
dB
dB
-73
—
dB
MHz
bits
Effective Number of Bits
9.4
—
Note 1: The Analog-to-Digital conversion result never decreases with an increase in input voltage, and has no
missing codes.
2: Module is functional at VBOR < VDD < VDDMIN, but with degraded performance. Module functionality is
tested but not characterized.
DS70000318G-page 328
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-41: 10-BIT, HIGH-SPEED ADC MODULE TIMING REQUIREMENTS
Standard Operating Conditions (see Note 2): 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
AC CHARACTERISTICS
-40°C TA +125°C for Extended
Param
No.
Symbol
Characteristic
Min.
Typ(1)
Max.
Units
Conditions
Clock Parameters
AD50b TAD
ADC Clock Period
35.8
—
—
—
ns
—
Conversion Rate
AD55b tCONV
AD56b FCNV
Conversion Time
—
14 TAD
Throughput Rate
Devices with Single SAR
Devices with Dual SARs
—
—
—
—
2.0
4.0
Msps
Msps
Timing Parameters
1.0
AD63b tDPU
Time to Stabilize Analog Stage
from ADC Off to ADC On
—
10
s
Note 1: These parameters are characterized but not tested in manufacturing.
2: Module is functional at VBOR < VDD < VDDMIN, but with degraded performance. Module functionality is
tested but not characterized.
FIGURE 24-23:
ANALOG-TO-DIGITAL CONVERSION TIMING PER INPUT
TCONV
Trigger Pulse
TAD
ADC Clock
ADC Data
9
8
2
1
0
ADBUFxx
CONV
Old Data
New Data
2008-2014 Microchip Technology Inc.
DS70000318G-page 329
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-42: COMPARATOR MODULE SPECIFICATIONS
Standard Operating Conditions (see Note 2): 3.0V to 3.6V
DC CHARACTERISTICS
Operating temperature: -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
Param.
No.
Symbol
Characteristic
Min
Typ
Max
Units
Comments
CM10
CM11
VIOFF
VICM
Input Offset Voltage
-58 +14/-40
66
mV
V
Input Common-Mode
Voltage Range(1)
0
—
AVDD – 1.5
CM12
VGAIN
Open Loop Gain(1)
90
70
—
—
—
—
db
db
CM13 CMRR
Common-Mode
Rejection Ratio(1)
CM14
TRESP
Large Signal Response 21
30
49
ns V+ input step of 100 mv while
V- input held at AVDD/2. Delay
measured from analog input pin to
PWM output pin.
Note 1: Parameters are for design guidance only and are not tested in manufacturing.
2: Module is functional at VBOR < VDD < VDDMIN, but with degraded performance. Module functionality is
tested but not characterized.
TABLE 24-43: DAC MODULE SPECIFICATIONS
Standard Operating Conditions (see Note 2): 3.0V to 3.6V
AC and DC CHARACTERISTICS
Operating temperature: -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
Param.
No.
Symbol
Characteristic
Min
Typ
Max
Units
Comments
DA01
DA08
DA02
DA03
EXTREF External Voltage Reference(1)
INTREF Internal Voltage Reference(1)
0
AVDD – 1.6
1.41
V
V
1.25
1.32
CVRES
INL
Resolution
10
Bits
Integral Nonlinearity Error
-7
-1
+7
LSB AVDD = 3.3V,
DACREF = (AVDD/2)V
DA04
DA05
DA06
DA07
DNL
EOFF
EG
Differential Nonlinearity Error
Offset Error
-5
-0.5
-0.8
+5
2.6
LSB
0.4
0.4
711
%
Gain Error
Settling Time(1)
-1.8
5.2
%
TSET
1551
2100
nsec Measured when
range = 1(high range),
and CMREF<9:0>
transitions from 0x1FF
to 0x300.
Note 1: Parameters are for design guidance only and are not tested in manufacturing.
2: Module is functional at VBOR < VDD < VDDMIN, but with degraded performance. Module functionality is
tested but not characterized.
DS70000318G-page 330
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 24-44: DAC OUTPUT BUFFER DC SPECIFICATIONS
Standard Operating Conditions (see Note 1): 3.0V to 3.6V
DC CHARACTERISTICS
Operating temperature: -40°C TA +85°C for Industrial
-40°C TA +125°C for Extended
Param.
Symbol
No.
Characteristic
Min
Typ
Max
Units
Comments
DA10
RLOAD
Resistive Output Load
Impedance
3K
—
—
DA11
DA12
CLOAD
IOUT
Output Load Capacitance
—
20
35
pF
Output Current Drive
Strength
-1740
±1400
+1770
A Sink and source
DA13
DA14
VRANGE Full Output Drive Strength AVSS + 250 mV
Voltage Range
—
—
AVDD – 900 mV
AVDD – 500 mV
V
V
VLRANGE Output Drive Voltage
Range at Reduced
AVSS + 50 mV
Current Drive of 50 A
DA15
IDD
Current Consumed when
Module is Enabled,
High-Power Mode
369
626
948
A Module will always
consume this
current even if no
load is connected to
the output
DA16
ROUTON Output Impedance when
Module is Enabled
—
1200
—
Note 1: Module is functional at VBOR < VDD < VDDMIN, but with degraded performance. Module functionality is
tested but not characterized.
2008-2014 Microchip Technology Inc.
DS70000318G-page 331
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 332
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
25.0 HIGH-TEMPERATURE ELECTRICAL CHARACTERISTICS
This section provides an overview of dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 electrical characteristics
for devices operating in an ambient temperature range of -40°C to +150°C.
Note:
Programming of the Flash memory is not allowed above +125°C.
The specifications between -40°C to +150°C are identical to those shown in Section 24.0 “Electrical Characteristics”
for operation between -40°C to +125°C, with the exception of the parameters listed in this section.
Parameters in this section begin with an H, which denotes High temperature. For example, Parameter DC10 in
Section 24.0 “Electrical Characteristics” is the Industrial and Extended temperature equivalent of HDC10.
Absolute maximum ratings for the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 high-temperature devices
are listed below. Exposure to these maximum rating conditions for extended periods can affect device reliability.
Functional operation of the device at these or any other conditions above the parameters indicated in the operation
listings of this specification is not implied.
(1)
Absolute Maximum Ratings
Ambient temperature under bias(3) .........................................................................................................-40°C to +150°C
Storage temperature .............................................................................................................................. -65°C to +160°C
Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V
Voltage on any pin that is not 5V tolerant with respect to VSS(4) .................................................... -0.3V to (VDD + 0.3V)
Voltage on any 5V tolerant pin with respect to VSS when VDD < 3.0V(4) ....................................... -0.3V to (VDD + 0.3V)
Voltage on any 5V tolerant pin with respect to VSS when VDD 3.0V(4) .................................................... -0.3V to 5.6V
Maximum current out of VSS pin .............................................................................................................................60 mA
Maximum current into VDD pin(2).............................................................................................................................60 mA
Maximum junction temperature............................................................................................................................. +155°C
Maximum current sourced/sunk by any 4x I/O pin....................................................................................................4 mA
Maximum current sourced/sunk by any 8x I/O pin....................................................................................................8 mA
Maximum current sourced/sunk by any 16x I/O pin................................................................................................16 mA
Maximum current sunk by all ports combined ......................................................................................................180 mA
Maximum current sourced by all ports combined(2) ..............................................................................................180 mA
Note 1: Stresses above those listed under “Absolute Maximum Ratings” can cause permanent damage to the
device. This is a stress rating only, and functional operation of the device at those or any other conditions
above those indicated in the operation listings of this specification is not implied. Exposure to maximum
rating conditions for extended periods can affect device reliability.
2: Maximum allowable current is a function of device maximum power dissipation (see Table 25-2).
3: AEC-Q100 reliability testing for devices intended to operate at 150°C is 1,000 hours. Any design in which
the total operating time from 125°C to 150°C will be greater than 1,000 hours is not warranted without prior
written approval from Microchip Technology Inc.
4: Refer to the “Pin Diagrams” section for 5V tolerant pins.
2008-2014 Microchip Technology Inc.
DS70000318G-page 333
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
25.1 High-Temperature DC Characteristics
TABLE 25-1: OPERATING MIPS VS. VOLTAGE
Max MIPS
VDD Range
(in Volts)
Temperature Range
(in °C)
Characteristic
dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04
—
3.0V to 3.6V(1)
-40°C to +150°C
20
Note 1: Overall functional device operation at VBORMIN < VDD < VDDMIN is tested but not characterized. All device
analog modules such as the ADC, etc., will function but with degraded performance below VDDMIN. Refer to
Parameter BO10 in Table 24-11 for BOR values.
TABLE 25-2: THERMAL OPERATING CONDITIONS
Rating
Symbol
Min
Typ
Max
Unit
High-Temperature Devices
Operating Junction Temperature Range
Operating Ambient Temperature Range
TJ
TA
-40
-40
—
—
+155
+150
°C
°C
Power Dissipation:
Internal chip power dissipation:
PINT = VDD x (IDD - IOH)
PD
PINT + PI/O
W
W
I/O Pin Power Dissipation:
I/O = ({VDD - VOH} x IOH) + (VOL x IOL)
Maximum Allowed Power Dissipation
PDMAX
(TJ - TA)/JA
TABLE 25-3: DC TEMPERATURE AND VOLTAGE SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +150°C for High Temperature
DC CHARACTERISTICS
Parameter
Symbol
No.
Characteristic
Min
Typ
Max
Units
Conditions
Operating Voltage
HDC10
Supply Voltage
VDD
—
3.0
3.3
3.6
V
-40°C to +150°C
DS70000318G-page 334
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 25-4: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)
Standard Operating Conditions: 3.0V to 3.6V
DC CHARACTERISTICS
(unless otherwise stated)
Operating temperature -40°C TA +150°C for High Temperature
Parameter
Typical(1)
No.
Max
Units
Conditions
Power-Down Current (IPD)(2,4)
HDC60e
HDC61c
1000
100
2000
110
A
A
+150°C
+150°C
3.3V
3.3V
Base Power-Down Current
(3)
Watchdog Timer Current: IWDT
Note 1: Data in the Typical column is at 3.3V, +25°C unless otherwise stated.
2: IPD (Sleep) current is measured as follows:
•
CPU core is off, oscillator is configured in EC mode and external clock active, OSC1 is driven with
external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
•
•
•
•
•
CLKO is configured as an I/O input pin in the Configuration Word
All I/O pins are configured as inputs and pulled to VSS
MCLR = VDD, WDT and FSCM are disabled
All peripheral modules are disabled (PMDx bits are all ones)
The VREGS bit (RCON<8>) = 0(i.e., core regulator is set to stand-by while the device is in
Sleep mode)
•
JTAG disabled
3: The current is the additional current consumed when the WDT module is enabled. This current should
be added to the base IPD current.
4: These currents are measured on the device containing the most memory in this family.
2008-2014 Microchip Technology Inc.
DS70000318G-page 335
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 25-5: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +150°C for High
DC CHARACTERISTICS
Temperature
Param. Symbol
Characteristic
Min.
Typ. Max. Units
Conditions
Output Low Voltage
I/O Pins:
4x Sink Driver Pins –
RA0-RA2, RB0-RB2, RB5-
RB10, RB15, RC1, RC2, RC9,
RC10
IOL 3.6 mA, VDD = 3.3V
See Note 1
—
—
0.4
V
Output Low Voltage
I/O Pins:
8x Sink Driver Pins – RC0,
RC3-RC8, RC11-RC13
DO10 VOL
IOL 6 mA, VDD = 3.3V
See Note 1
—
—
—
—
0.4
0.4
V
V
Output Low Voltage
I/O Pins:
16x Sink Driver Pins – RA3,
RA4, RB3, RB4, RB11-RB14
IOL 12 mA, VDD = 3.3V
See Note 1
Output High Voltage
I/O Pins:
4x Source Driver Pins –
RA0-RA2, RB0-RB2, RB5-
RB10, RB15, RC1, RC2, RC9,
RC10
IOL -4 mA, VDD = 3.3V
See Note 1
2.4
—
—
V
Output High Voltage
I/O Pins:
8x Source Driver Pins – RC0,
RC3-RC8, RC11-RC13
DO20 VOH
IOL -8 mA, VDD = 3.3V
See Note 1
2.4
2.4
—
—
—
—
V
V
Output High Voltage
I/O Pins:
16x Source Driver Pins – RA3,
RA4, RB3, RB4, RB11-RB14
IOL -16 mA, VDD = 3.3V
See Note 1
Output High Voltage
I/O Pins:
4x Source Driver Pins –
RA0-RA2, RB0-RB2, RB5-
RB10, RB15, RC1, RC2, RC9,
RC10
IOH -3.9 mA, VDD = 3.3V
See Note 1
1.5
2.0
3.0
1.5
2.0
3.0
1.5
2.0
3.0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
IOH -3.7 mA, VDD = 3.3V
See Note 1
V
V
V
IOH -2 mA, VDD = 3.3V
See Note 1
Output High Voltage
I/O Pins:
8x Source Driver Pins – RC0,
RC3-RC8, RC11-RC13
IOH -7.5 mA, VDD = 3.3V
See Note 1
IOH -6.8 mA, VDD = 3.3V
See Note 1
DO20A VOH1
IOH -3 mA, VDD = 3.3V
See Note 1
Output High Voltage
I/O Pins:
16x Source Driver Pins – RA3,
RA4, RB3, RB4, RB11-RB14
IOH -15 mA, VDD = 3.3V
See Note 1
IOH -14 mA, VDD = 3.3V
See Note 1
IOH -7 mA, VDD = 3.3V
See Note 1
Note 1: Parameters are characterized, but not tested.
DS70000318G-page 336
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 25-6: DC CHARACTERISTICS: PROGRAM MEMORY
Standard Operating Conditions: 3.0V to 3.6V
DC CHARACTERISTICS
(unless otherwise stated)
Operating temperature -40°C TA +150°C for High Temperature
Param
No.
Symbol
Characteristic(1)
Min
Typ
Max
Units
Conditions
Program Flash Memory
Cell Endurance
HD130 EP
10,000
20
—
—
—
—
E/W -40C to +150C(2)
HD134 TRETD
Characteristic Retention
Year 1000 E/W cycles or less and no
other specifications are violated
Note 1: These parameters are assured by design, but are not characterized or tested in manufacturing.
2: Programming of the Flash memory is not allowed above +125°C.
2008-2014 Microchip Technology Inc.
DS70000318G-page 337
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Parameters in this section begin with an H, which denotes
High temperature. For example, Parameter OS53 in
Section 24.2 “AC Characteristics and Timing
25.2 AC Characteristics and Timing
Parameters
The information contained in this section defines
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/
X04 AC characteristics and timing parameters for high-
temperature devices. However, all AC timing
specifications in this section are the same as those in
Section 24.2 “AC Characteristics and Timing
Parameters”, with the exception of the parameters
listed in this section.
Parameters” is the Industrial and Extended temperature
equivalent of HOS53.
TABLE 25-7: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C TA +150°C for High Temperature
AC CHARACTERISTICS
Operating voltage VDD range as described in Table 25-1.
FIGURE 25-1:
LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load Condition 1 – for all pins except OSC2
VDD/2
Load Condition 2 – for OSC2
CL
RL
Pin
VSS
CL
Pin
RL = 464
CL = 50 pF for all pins except OSC2
15 pF for OSC2 output
VSS
TABLE 25-8: PLL CLOCK TIMING SPECIFICATIONS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C TA +150°C for High Temperature
AC
CHARACTERISTICS
Param
Symbol
No.
Characteristic
Min
Typ
Max
Units
Conditions
HOS53
DCLK
CLKO Stability (Jitter)(1)
-5
0.5
5
%
Measured over 100 ms
period
Note 1: These parameters are characterized, but are not tested in manufacturing.
DS70000318G-page 338
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 25-9: SPIx MASTER MODE (CKE = 0) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC CHARACTERISTICS
Operating temperature -40°C TA +150°C for High Temperature
Param
No.
Symbol
Characteristic(1)
Min
Typ
Max Units
Conditions
HSP35
TscH2doV,
TscL2doV
SDOx Data Output Valid after
SCKx Edge
—
10
25
—
—
ns
ns
ns
HSP40
HSP41
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
28
35
—
—
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
Note 1: These parameters are characterized but not tested in manufacturing.
TABLE 25-10: SPIx MODULE MASTER MODE (CKE = 1) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C TA +150°C for High Temperature
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic(1)
Min
Typ
Max Units
Conditions
HSP35
HSP36
HSP40
HSP41
TscH2doV,
TscL2doV
SDOx Data Output Valid after
SCKx Edge
—
10
25
—
—
—
ns
ns
ns
ns
TdoV2sc,
TdoV2scL
SDOx Data Output Setup to
First SCKx Edge
35
28
35
—
—
—
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
Note 1: These parameters are characterized but not tested in manufacturing.
2008-2014 Microchip Technology Inc.
DS70000318G-page 339
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 25-11: SPIx MODULE SLAVE MODE (CKE = 0) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
AC CHARACTERISTICS
Operating temperature -40°C TA +150°C for High Temperature
Param
No.
Symbol
Characteristic(1)
Min
Typ
Max Units
Conditions
HSP35
TscH2doV,
TscL2doV
SDOx Data Output Valid after
SCKx Edge
—
—
35
—
—
55
ns
ns
ns
ns
HSP40
HSP41
HSP51
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
25
25
15
—
—
—
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input to
SCKx Edge
TssH2doZ
SSx to SDOx Output
See Note 2
High-Impedance
Note 1: These parameters are characterized but not tested in manufacturing.
2: Assumes 50 pF load on all SPIx pins.
TABLE 25-12: SPIx MODULE SLAVE MODE (CKE = 1) TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated)
Operating temperature -40°C TA +150°C for High Temperature
AC CHARACTERISTICS
Param
Symbol
No.
Characteristic(1)
Min
Typ
Max
Units
Conditions
HSP35
HSP40
HSP41
HSP51
HSP60
TscH2doV, SDOx Data Output Valid after
—
—
35
ns
TscL2doV
SCKx Edge
TdiV2scH,
TdiV2scL
Setup Time of SDIx Data Input
to SCKx Edge
25
25
15
—
—
—
—
—
—
—
55
55
ns
ns
ns
ns
TscH2diL,
TscL2diL
Hold Time of SDIx Data Input
to SCKx Edge
TssH2doZ
SSx to SDOX Output
See Note 2
High-Impedance
TssL2doV
SDOx Data Output Valid after
SSx Edge
Note 1: These parameters are characterized but not tested in manufacturing.
2: Assumes 50 pF load on all SPIx pins.
DS70000318G-page 340
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
26.0 50 MIPS ELECTRICAL CHARACTERISTICS
This section provides an overview of dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 electrical characteristics
for devices operating at 50 MIPS.
The specifications for 50 MIPS are identical to those shown in Section 24.0 “Electrical Characteristics”, with the
exception of the parameters listed in this section.
Parameters in this section begin with the letter “M”, which denotes 50 MIPS operation. For example, Parameter DC29a
in Section 24.0 “Electrical Characteristics”, is the up to 40 MIPS operation equivalent of MDC29a.
Absolute maximum ratings for the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 50 MIPS devices are listed
below. Exposure to these maximum rating conditions for extended periods can affect device reliability. Functional
operation of the device at these or any other conditions above the parameters indicated in the operation listings of this
specification is not implied.
(1)
Absolute Maximum Ratings
Ambient temperature under bias...............................................................................................................-40°C to +85°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +4.0V
Voltage on any pin that is not 5V tolerant, with respect to VSS(3) ................................................... -0.3V to (VDD + 0.3V)
Voltage on any 5V tolerant pin with respect to VSS, when Vdd 3.0V(3) ................................................. -0.3V to +5.6V
Voltage on any 5V tolerant pin with respect to Vss, when VDD < 3.0V(3)........................................ -0.3V to (VDD + 0.3V)
Maximum current out of VSS pin ...........................................................................................................................300 mA
Maximum current into VDD pin(2)...........................................................................................................................250 mA
Maximum current sourced/sunk by any 4x I/O pin..................................................................................................15 mA
Maximum current sourced/sunk by any 8x I/O pin..................................................................................................25 mA
Maximum current sourced/sunk by any 16x I/O pin................................................................................................45 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports(2)...............................................................................................................200mA
Note 1: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only, and functional operation of the device at those or any other conditions
above those indicated in the operation listings of this specification is not implied. Exposure to maximum
rating conditions for extended periods may affect device reliability.
2: Maximum allowable current is a function of device maximum power dissipation (see Table 24-2).
3: See the “Pin Diagrams” section for 5V tolerant pins.
2008-2014 Microchip Technology Inc.
DS70000318G-page 341
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
26.1 DC Characteristics
TABLE 26-1: OPERATING MIPS VS. VOLTAGE
Max MIPS
VDD Range
(in Volts)
Temp Range
(in °C)
Characteristic
dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04
—
3.0-3.6V(1)
-40°C to +85°C
50
Note 1: Overall functional device operation at VBORMIN < VDD < VDDMIN is tested but not characterized. All device
analog modules, such as the ADC, etc., will function but with degraded performance below VDDMIN. Refer
to Parameter BO10 in Table 24-11 for BOR values.
TABLE 26-2: DC CHARACTERISTICS: OPERATING CURRENT (IDD)
Standard Operating Conditions: 3.0V to 3.6V
DC CHARACTERISTICS
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
Parameter
Typical
No.
Max
Units
Conditions
Operating Current (IDD)(1)
MDC29d
MDC29a
MDC29b
105
105
105
125
125
125
mA
mA
mA
-40°C
+25°C
+85°C
3.3V
50 MIPS
Note 1: IDD is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact
on the current consumption. The test conditions for all IDD measurements are as follows:
• Oscillator is configured in EC mode with PLL, OSC1 is driven with external square wave from
rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
• CLKO is configured as an I/O input pin in the Configuration Word
• All I/O pins are configured as inputs and pulled to VSS
• MCLR = VDD, WDT and FSCM are disabled
• CPU, SRAM, program memory and data memory are operational
• No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits
are zeroed)
• CPU executing while(1)statement
• JTAG is disabled
DS70000318G-page 342
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 26-3: DC CHARACTERISTICS: IDLE CURRENT (IIDLE)
Standard Operating Conditions: 3.0V to 3.6V
DC CHARACTERISTICS
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
Parameter
Typical
No.
Max
Units
Conditions
Idle Current (IIDLE): Core Off, Clock On Base Current(1)
MDC45d
MDC45a
MDC45b
64
64
64
105
105
105
mA
mA
mA
-40°C
+25°C
+85°C
3.3V
50 MIPS
Note 1: Base Idle current (IIDLE) is measured as follows:
•
CPU core is off, oscillator is configured in EC mode and external clock active, OSC1 is driven with
external square wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
•
•
•
•
CLKO is configured as an I/O input pin in the Configuration Word
All I/O pins are configured as inputs and pulled to VSS
MCLR = VDD, WDT and FSCM are disabled
No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits
are zeroed)
•
•
The NVMSIDL bit (NVMCON<12>) = 1(i.e., Flash regulator is set to standby while the device is in
Idle mode)
JTAG is disabled
2008-2014 Microchip Technology Inc.
DS70000318G-page 343
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE 26-4: DC CHARACTERISTICS: DOZE CURRENT (IDOZE)(1)
Standard Operating Conditions: 3.0V to 3.6V
DC CHARACTERISTICS
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
Doze
Ratio
Parameter No.
Typical
Max
Units
Conditions
MDC74a
MDC74f
MDC74g
MDC75a
MDC75f
MDC75g
MDC76a
MDC76f
MDC76g
80
65
65
81
65
65
81
65
65
105
105
105
105
105
105
105
105
105
1:2
1:64
1:128
1:2
mA
mA
mA
mA
mA
mA
mA
mA
mA
-40°C
+25°C
+85°C
3.3V
50 MIPS
50 MIPS
50 MIPS
1:64
1:128
1:2
3.3V
3.3V
1:64
1:128
Note 1: IDOZE is primarily a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact
on the current consumption. The test conditions for all IDOZE measurements are as follows:
•
Oscillator is configured in EC mode and external clock active, OSC1 is driven with external square
wave from rail-to-rail (EC clock overshoot/undershoot < 250 mV required)
•
•
•
•
•
CLKO is configured as an I/O input pin in the Configuration Word
All I/O pins are configured as inputs and pulled to VSS
MCLR = VDD, WDT and FSCM are disabled
CPU, SRAM, program memory and data memory are operational
No peripheral modules are operating; however, every peripheral is being clocked (all PMDx bits
are zeroed)
•
•
CPU executing while(1)statement
JTAG is disabled
DS70000318G-page 344
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
26.2 AC Characteristics and Timing Parameters
This section defines the dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 AC characteristics and timing
parameters for 50 MIPS devices.
TABLE 26-5: EXTERNAL CLOCK TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
AC CHARACTERISTICS
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
Param
Symb
No.
Characteristic
Min
Typ(1)
Max
Units
Conditions
MOS10 FIN
External CLKI Frequency
(External clocks allowed only
in EC and ECPLL modes)
DC
—
50
MHz EC
Oscillator Crystal Frequency
3.5
10
—
—
10
50
MHz XT
MHz HS
MOS20 TOSC
MOS25 TCY
TOSC = 1/FOSC
Instruction Cycle Time(2)
10
20
—
—
DC
DC
ns
ns
Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated.
2: Instruction cycle period (TCY) equals two times the input oscillator time base period. All specified values
are based on characterization data for that particular oscillator type, under standard operating conditions,
with the device executing code. Exceeding these specified limits may result in an unstable oscillator
operation and/or higher than expected current consumption. All devices are tested to operate at “Min.”
values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the
“Max.” cycle time limit is “DC” (no clock) for all devices.
TABLE 26-6: SIMPLE OCx/PWMx MODE TIMING REQUIREMENTS
Standard Operating Conditions: 3.0V to 3.6V
AC CHARACTERISTICS
(unless otherwise stated)
Operating temperature -40°C TA +85°C for Industrial
Param
Symbol
No.
Characteristic(1)
Min
Typ
Max
Units
Conditions
MOC15 TFD
Fault Input to PWMx I/O
Change
—
—
TCY + 10
ns
MOC20 TFLT
Fault Input Pulse Width
TCY + 10
—
—
ns
Note 1: These parameters are characterized but not tested in manufacturing.
2008-2014 Microchip Technology Inc.
DS70000318G-page 345
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 346
2008-2014 Microchip Technology Inc.
27.0 DC AND AC DEVICE CHARACTERISTICS GRAPHS
Note: The graphs provided following this note are a statistical summary based on a limited number of samples and are provided for design guidance purposes
only. The performance characteristics listed herein are not tested or guaranteed. In some graphs, the data presented may be outside the specified operating
range (e.g., outside specified power supply range) and therefore, outside the warranted range.
FIGURE 27-1:
VOH – 4x DRIVER PINS
FIGURE 27-3:
VOH – 16x DRIVER PINS
3.6V
3.6V
3.3V
3.3V
3V
Absolute Maximum
Absolute Maximum
3V
FIGURE 27-2:
VOH – 8x DRIVER PINS
3.6V
3.3V
Absolute Maximum
3V
FIGURE 27-4:
VOL – 4x DRIVER PINS
FIGURE 27-6:
VOL – 16x DRIVER PINS
3.6V
3.6V
3.3V
3.3V
3V
3V
Absolute Maximum
Absolute Maximum
FIGURE 27-5:
VOL – 8x DRIVER PINS
3.6V
3.3V
3V
Absolute Maximum
FIGURE 27-7:
TYPICAL IPD CURRENT @ VDD = 3.3V
FIGURE 27-9:
TYPICAL IDOZE CURRENT @ VDD = 3.3V
50 MIPS
40 MIPS
48
FIGURE 27-8:
TYPICAL IDD CURRENT @ VDD = 3.3V
FIGURE 27-10:
TYPICAL IIDLE CURRENT @ VDD = 3.3V
FIGURE 27-11:
TYPICAL FRC FREQUENCY @ VDD = 3.3V
FIGURE 27-13:
TYPICAL INTREF @ VDD = 3.3V
FIGURE 27-12:
TYPICAL LPRC FREQUENCY @ VDD = 3.3V
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
28.0 PACKAGING INFORMATION
28.1 Package Marking Information
18-Lead SOIC (.300”)
Example
XXXXXXXXXXXX
XXXXXXXXXXXX
XXXXXXXXXXXX
dsPIC33FJ06
GS101-I/SO
e
3
YYWWNNN
0830235
28-Lead SOIC
Example
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
dsPIC33FJ06GS
e
3
202-E/SO
YYWWNNN
0830235
28-Lead SPDIP
Example
dsPIC33FJ06GS
202-E/SP
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
e
3
YYWWNNN
0830235
28-Lead QFN-S
Example
XXXXXXXX
XXXXXXXX
YYWWNNN
33FJ06GS
202EMM
0830235
e
3
Legend: XX...X Customer-specific information
Y
Year code (last digit of calendar year)
YY
Year code (last 2 digits of calendar year)
WW
NNN
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
e
3
*
)
e
3
Note: If the full Microchip part number cannot be marked on one line, it is carried over to the next
line, thus limiting the number of available characters for customer-specific information.
2008-2014 Microchip Technology Inc.
DS70000318G-page 351
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
28.1 Package Marking Information (Continued)
28-Lead UQFN
Example
XXXXXXXX
XXXXXXXX
YYWWNNN
33FJ06GS
202EMX
0830235
e
3
44-Lead QFN
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
dsPIC33FJ16
GS504-E/ML
e
3
0830235
44-Lead TQFP
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
YYWWNNN
dsPIC33FJ
16GS504
e
3
-E/PT
0830235
44-Lead VTLA (TLA)
Example
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
dsPIC33FJ
16GS504
-E/TL
e
3
YYWWNNN
0830235
DS70000318G-page 352
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
28.2 Package Details
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2008-2014 Microchip Technology Inc.
DS70000318G-page 353
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS70000318G-page 354
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2008-2014 Microchip Technology Inc.
DS70000318G-page 355
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS70000318G-page 356
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2008-2014 Microchip Technology Inc.
DS70000318G-page 357
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS70000318G-page 358
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢉꢊꢋꢋꢌꢇꢍꢎꢅꢏꢐꢊꢑꢇꢒꢓꢅꢎꢇꢔꢋꢂꢃꢊꢋꢄꢇꢕꢈꢍꢖꢇMꢇꢗꢘꢘꢇꢙꢊꢎꢇꢚꢛꢆꢌꢇꢜꢈꢍꢒꢔꢍ
!ꢛꢐꢄ" 3ꢋꢉꢅ&ꢍꢈꢅ'ꢋ!&ꢅꢌ"ꢉꢉꢈꢄ&ꢅꢓꢆꢌ4ꢆꢑꢈꢅ#ꢉꢆ*ꢃꢄꢑ!(ꢅꢓꢇꢈꢆ!ꢈꢅ!ꢈꢈꢅ&ꢍꢈꢅꢔꢃꢌꢉꢋꢌꢍꢃꢓꢅꢂꢆꢌ4ꢆꢑꢃꢄꢑꢅꢐꢓꢈꢌꢃ%ꢃꢌꢆ&ꢃꢋꢄꢅꢇꢋꢌꢆ&ꢈ#ꢅꢆ&ꢅ
ꢍ&&ꢓ255***ꢁ'ꢃꢌꢉꢋꢌꢍꢃꢓꢁꢌꢋ'5ꢓꢆꢌ4ꢆꢑꢃꢄꢑ
N
NOTE 1
E1
1
2 3
D
E
A2
A
L
c
b1
A1
b
e
eB
6ꢄꢃ&!
ꢒꢃ'ꢈꢄ!ꢃꢋꢄꢅ9ꢃ'ꢃ&!
ꢚ7,8.ꢐ
7:ꢔ
ꢎ<
ꢁꢀꢕꢕꢅ1ꢐ,
M
ꢔꢚ7
ꢔꢗ;
7"')ꢈꢉꢅꢋ%ꢅꢂꢃꢄ!
ꢂꢃ&ꢌꢍ
7
ꢈ
ꢗ
ꢙꢋꢓꢅ&ꢋꢅꢐꢈꢆ&ꢃꢄꢑꢅꢂꢇꢆꢄꢈ
M
ꢁꢎꢕꢕ
ꢁꢀꢘꢕ
M
ꢔꢋꢇ#ꢈ#ꢅꢂꢆꢌ4ꢆꢑꢈꢅꢙꢍꢃꢌ4ꢄꢈ!!
1ꢆ!ꢈꢅ&ꢋꢅꢐꢈꢆ&ꢃꢄꢑꢅꢂꢇꢆꢄꢈ
ꢐꢍꢋ"ꢇ#ꢈꢉꢅ&ꢋꢅꢐꢍꢋ"ꢇ#ꢈꢉꢅ>ꢃ#&ꢍ
ꢔꢋꢇ#ꢈ#ꢅꢂꢆꢌ4ꢆꢑꢈꢅ>ꢃ#&ꢍ
: ꢈꢉꢆꢇꢇꢅ9ꢈꢄꢑ&ꢍ
ꢙꢃꢓꢅ&ꢋꢅꢐꢈꢆ&ꢃꢄꢑꢅꢂꢇꢆꢄꢈ
9ꢈꢆ#ꢅꢙꢍꢃꢌ4ꢄꢈ!!
6ꢓꢓꢈꢉꢅ9ꢈꢆ#ꢅ>ꢃ#&ꢍ
ꢗꢎ
ꢗꢀ
.
.ꢀ
ꢒ
9
ꢌ
)ꢀ
)
ꢈ1
ꢁꢀꢎꢕ
ꢁꢕꢀꢘ
ꢁꢎꢛꢕ
ꢁꢎꢖꢕ
ꢀꢁ-ꢖꢘ
ꢁꢀꢀꢕ
ꢁꢕꢕ<
ꢁꢕꢖꢕ
ꢁꢕꢀꢖ
M
ꢁꢀ-ꢘ
M
ꢁ-ꢀꢕ
ꢁꢎ<ꢘ
ꢀꢁ-?ꢘ
ꢁꢀ-ꢕ
ꢁꢕꢀꢕ
ꢁꢕꢘꢕ
ꢁꢕꢀ<
M
ꢁ--ꢘ
ꢁꢎꢛꢘ
ꢀꢁꢖꢕꢕ
ꢁꢀꢘꢕ
ꢁꢕꢀꢘ
ꢁꢕꢜꢕ
ꢁꢕꢎꢎ
ꢁꢖ-ꢕ
9ꢋ*ꢈꢉꢅ9ꢈꢆ#ꢅ>ꢃ#&ꢍ
: ꢈꢉꢆꢇꢇꢅꢝꢋ*ꢅꢐꢓꢆꢌꢃꢄꢑꢅꢅꢏ
!ꢛꢐꢄꢏ"
ꢀꢁ ꢂꢃꢄꢅꢀꢅ ꢃ!"ꢆꢇꢅꢃꢄ#ꢈ$ꢅ%ꢈꢆ&"ꢉꢈꢅ'ꢆꢊꢅ ꢆꢉꢊ(ꢅ)"&ꢅ'"!&ꢅ)ꢈꢅꢇꢋꢌꢆ&ꢈ#ꢅ*ꢃ&ꢍꢃꢄꢅ&ꢍꢈꢅꢍꢆ&ꢌꢍꢈ#ꢅꢆꢉꢈꢆꢁ
ꢎꢁ ꢏꢅꢐꢃꢑꢄꢃ%ꢃꢌꢆꢄ&ꢅ,ꢍꢆꢉꢆꢌ&ꢈꢉꢃ!&ꢃꢌꢁ
-ꢁ ꢒꢃ'ꢈꢄ!ꢃꢋꢄ!ꢅꢒꢅꢆꢄ#ꢅ.ꢀꢅ#ꢋꢅꢄꢋ&ꢅꢃꢄꢌꢇ"#ꢈꢅ'ꢋꢇ#ꢅ%ꢇꢆ!ꢍꢅꢋꢉꢅꢓꢉꢋ&ꢉ"!ꢃꢋꢄ!ꢁꢅꢔꢋꢇ#ꢅ%ꢇꢆ!ꢍꢅꢋꢉꢅꢓꢉꢋ&ꢉ"!ꢃꢋꢄ!ꢅ!ꢍꢆꢇꢇꢅꢄꢋ&ꢅꢈ$ꢌꢈꢈ#ꢅꢁꢕꢀꢕ/ꢅꢓꢈꢉꢅ!ꢃ#ꢈꢁ
ꢖꢁ ꢒꢃ'ꢈꢄ!ꢃꢋꢄꢃꢄꢑꢅꢆꢄ#ꢅ&ꢋꢇꢈꢉꢆꢄꢌꢃꢄꢑꢅꢓꢈꢉꢅꢗꢐꢔ.ꢅ0ꢀꢖꢁꢘꢔꢁ
1ꢐ,2 1ꢆ!ꢃꢌꢅꢒꢃ'ꢈꢄ!ꢃꢋꢄꢁꢅꢙꢍꢈꢋꢉꢈ&ꢃꢌꢆꢇꢇꢊꢅꢈ$ꢆꢌ&ꢅ ꢆꢇ"ꢈꢅ!ꢍꢋ*ꢄꢅ*ꢃ&ꢍꢋ"&ꢅ&ꢋꢇꢈꢉꢆꢄꢌꢈ!ꢁ
ꢔꢃꢌꢉꢋꢌꢍꢃꢓ ꢙꢈꢌꢍꢄꢋꢇꢋꢑꢊ ꢒꢉꢆ*ꢃꢄꢑ ,ꢕꢖꢞꢕꢜꢕ1
2008-2014 Microchip Technology Inc.
DS70000318G-page 359
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
ꢀꢁꢂꢃꢄꢅꢆꢇꢍꢎꢅꢏꢐꢊꢑꢇ#ꢓꢅꢆꢇ$ꢎꢅꢐ%ꢇ!ꢛꢇꢃꢄꢅꢆꢇꢍꢅꢑꢉꢅ&ꢄꢇꢕ''ꢖꢇMꢇ()()ꢘ*+ꢇꢙꢙꢇꢚꢛꢆꢌꢇꢜ#$!ꢂꢈ
,ꢊꢐ-ꢇꢘ*.ꢘꢇꢙꢙꢇ/ꢛꢋꢐꢅꢑꢐꢇꢃꢄꢋ&ꢐ-
!ꢛꢐꢄ" 3ꢋꢉꢅ&ꢍꢈꢅ'ꢋ!&ꢅꢌ"ꢉꢉꢈꢄ&ꢅꢓꢆꢌ4ꢆꢑꢈꢅ#ꢉꢆ*ꢃꢄꢑ!(ꢅꢓꢇꢈꢆ!ꢈꢅ!ꢈꢈꢅ&ꢍꢈꢅꢔꢃꢌꢉꢋꢌꢍꢃꢓꢅꢂꢆꢌ4ꢆꢑꢃꢄꢑꢅꢐꢓꢈꢌꢃ%ꢃꢌꢆ&ꢃꢋꢄꢅꢇꢋꢌꢆ&ꢈ#ꢅꢆ&ꢅ
ꢍ&&ꢓ255***ꢁ'ꢃꢌꢉꢋꢌꢍꢃꢓꢁꢌꢋ'5ꢓꢆꢌ4ꢆꢑꢃꢄꢑ
D2
D
EXPOSED
PAD
e
E2
E
b
2
1
2
1
K
N
N
L
NOTE 1
BOTTOM VIEW
TOP VIEW
A
A3
A1
6ꢄꢃ&!
ꢒꢃ'ꢈꢄ!ꢃꢋꢄꢅ9ꢃ'ꢃ&!
ꢔꢚ99ꢚꢔ.ꢙ.ꢝꢐ
7:ꢔ
ꢔꢚ7
ꢔꢗ;
7"')ꢈꢉꢅꢋ%ꢅꢂꢃꢄ!
ꢂꢃ&ꢌꢍ
: ꢈꢉꢆꢇꢇꢅ8ꢈꢃꢑꢍ&
ꢐ&ꢆꢄ#ꢋ%%ꢅ
,ꢋꢄ&ꢆꢌ&ꢅꢙꢍꢃꢌ4ꢄꢈ!!
: ꢈꢉꢆꢇꢇꢅ>ꢃ#&ꢍ
.$ꢓꢋ!ꢈ#ꢅꢂꢆ#ꢅ>ꢃ#&ꢍ
: ꢈꢉꢆꢇꢇꢅ9ꢈꢄꢑ&ꢍ
.$ꢓꢋ!ꢈ#ꢅꢂꢆ#ꢅ9ꢈꢄꢑ&ꢍ
,ꢋꢄ&ꢆꢌ&ꢅ>ꢃ#&ꢍ
,ꢋꢄ&ꢆꢌ&ꢅ9ꢈꢄꢑ&ꢍ
,ꢋꢄ&ꢆꢌ&ꢞ&ꢋꢞ.$ꢓꢋ!ꢈ#ꢅꢂꢆ#
7
ꢈ
ꢗ
ꢗꢀ
ꢗ-
.
.ꢎ
ꢒ
ꢎ<
ꢕꢁ?ꢘꢅ1ꢐ,
ꢕꢁꢛꢕ
ꢕꢁ<ꢕ
ꢕꢁꢕꢕ
ꢀꢁꢕꢕ
ꢕꢁꢕꢘ
ꢕꢁꢕꢎ
ꢕꢁꢎꢕꢅꢝ.3
?ꢁꢕꢕꢅ1ꢐ,
-ꢁꢜꢕ
?ꢁꢕꢕꢅ1ꢐ,
-ꢁꢜꢕ
ꢕꢁ-<
ꢕꢁꢖꢕ
M
-ꢁ?ꢘ
ꢖꢁꢜꢕ
ꢒꢎ
)
9
-ꢁ?ꢘ
ꢕꢁꢎ-
ꢕꢁ-ꢕ
ꢕꢁꢎꢕ
ꢖꢁꢜꢕ
ꢕꢁꢖ-
ꢕꢁꢘꢕ
M
@
!ꢛꢐꢄꢏ"
ꢀꢁ ꢂꢃꢄꢅꢀꢅ ꢃ!"ꢆꢇꢅꢃꢄ#ꢈ$ꢅ%ꢈꢆ&"ꢉꢈꢅ'ꢆꢊꢅ ꢆꢉꢊ(ꢅ)"&ꢅ'"!&ꢅ)ꢈꢅꢇꢋꢌꢆ&ꢈ#ꢅ*ꢃ&ꢍꢃꢄꢅ&ꢍꢈꢅꢍꢆ&ꢌꢍꢈ#ꢅꢆꢉꢈꢆꢁ
ꢎꢁ ꢂꢆꢌ4ꢆꢑꢈꢅꢃ!ꢅ!ꢆ*ꢅ!ꢃꢄꢑ"ꢇꢆ&ꢈ#ꢁ
-ꢁ ꢒꢃ'ꢈꢄ!ꢃꢋꢄꢃꢄꢑꢅꢆꢄ#ꢅ&ꢋꢇꢈꢉꢆꢄꢌꢃꢄꢑꢅꢓꢈꢉꢅꢗꢐꢔ.ꢅ0ꢀꢖꢁꢘꢔꢁ
1ꢐ,2 1ꢆ!ꢃꢌꢅꢒꢃ'ꢈꢄ!ꢃꢋꢄꢁꢅꢙꢍꢈꢋꢉꢈ&ꢃꢌꢆꢇꢇꢊꢅꢈ$ꢆꢌ&ꢅ ꢆꢇ"ꢈꢅ!ꢍꢋ*ꢄꢅ*ꢃ&ꢍꢋ"&ꢅ&ꢋꢇꢈꢉꢆꢄꢌꢈ!ꢁ
ꢝ.32 ꢝꢈ%ꢈꢉꢈꢄꢌꢈꢅꢒꢃ'ꢈꢄ!ꢃꢋꢄ(ꢅ"!"ꢆꢇꢇꢊꢅ*ꢃ&ꢍꢋ"&ꢅ&ꢋꢇꢈꢉꢆꢄꢌꢈ(ꢅ%ꢋꢉꢅꢃꢄ%ꢋꢉ'ꢆ&ꢃꢋꢄꢅꢓ"ꢉꢓꢋ!ꢈ!ꢅꢋꢄꢇꢊꢁ
ꢔꢃꢌꢉꢋꢌꢍꢃꢓ ꢙꢈꢌꢍꢄꢋꢇꢋꢑꢊ ꢒꢉꢆ*ꢃꢄꢑ ,ꢕꢖꢞꢀꢎꢖ1
DS70000318G-page 360
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
ꢀꢁꢂꢃꢄꢅꢆꢇꢍꢎꢅꢏꢐꢊꢑꢇ#ꢓꢅꢆꢇ$ꢎꢅꢐ%ꢇ!ꢛꢇꢃꢄꢅꢆꢇꢍꢅꢑꢉꢅ&ꢄꢇꢕ''ꢖꢇMꢇ()()ꢘ*+ꢇꢙꢙꢇꢚꢛꢆꢌꢇꢜ#$!ꢂꢈ
,ꢊꢐ-ꢇꢘ*.ꢘꢇꢙꢙꢇ/ꢛꢋꢐꢅꢑꢐꢇꢃꢄꢋ&ꢐ-
!ꢛꢐꢄ" 3ꢋꢉꢅ&ꢍꢈꢅ'ꢋ!&ꢅꢌ"ꢉꢉꢈꢄ&ꢅꢓꢆꢌ4ꢆꢑꢈꢅ#ꢉꢆ*ꢃꢄꢑ!(ꢅꢓꢇꢈꢆ!ꢈꢅ!ꢈꢈꢅ&ꢍꢈꢅꢔꢃꢌꢉꢋꢌꢍꢃꢓꢅꢂꢆꢌ4ꢆꢑꢃꢄꢑꢅꢐꢓꢈꢌꢃ%ꢃꢌꢆ&ꢃꢋꢄꢅꢇꢋꢌꢆ&ꢈ#ꢅꢆ&ꢅ
ꢍ&&ꢓ255***ꢁ'ꢃꢌꢉꢋꢌꢍꢃꢓꢁꢌꢋ'5ꢓꢆꢌ4ꢆꢑꢃꢄꢑ
2008-2014 Microchip Technology Inc.
DS70000318G-page 361
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
28-Lead Plastic Quad Flat, No Lead Package (MX) - 6x6x0.5mm Body [UQFN]
Ultra-Thin with 0.40 x 0.60 mm Terminal Width/Length and Corner Anchors
Note: )RUꢅWKHꢅPRVWꢅFXUUHQWꢅSDFNDJHꢅGUDZLQJVꢆꢅSOHDVHꢅVHHꢅWKHꢅ0LFURFKLSꢅ3DFNDJLQJꢅ6SHFLILFDWLRQꢅORFDWHGꢅDW
KWWSꢇꢈꢈZZZꢁPLFURFKLSꢁFRPꢈSDFNDJLQJ
'
$
%
(
1
127(ꢅꢂ
ꢂ
ꢄ
ꢍ'$780ꢅ$ꢎ
ꢍ'$780ꢅ%ꢎ
ꢄ;
ꢀꢁꢂꢃ &
ꢄ;
ꢀꢁꢂꢃ &
723ꢅ9,(:
$
&
ꢀꢁꢂꢀ &
6($7,1*
3/$1(
ꢅ
ꢍ$ꢏꢎ
$ꢂ
Eꢄ
ꢀꢁꢀꢌ &
127(ꢅꢉ
6,'(ꢅ9,(:
'ꢄ
ꢀꢁꢂꢀ
& $ %
H
(ꢄ
.
ꢄ
ꢂ
1
/
127(ꢅꢉ
E
ꢀꢁꢂꢀ
ꢀꢁꢀꢃ
& $ %
&
%27720ꢅ9,(:
0LFURFKLSꢅ7HFKQRORJ\ꢅ'UDZLQJꢅꢅ&ꢀꢉꢊꢀꢄꢀꢋ%ꢅ6KHHWꢅꢂꢅRIꢅꢄ
DS70000318G-page 362
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
28-Lead Plastic Quad Flat, No Lead Package (MX) - 6x6x0.5mm Body [UQFN]
Ultra-Thin with 0.40 x 0.60 mm Terminal Width/Length and Corner Anchors
Note: )RUꢅWKHꢅPRVWꢅFXUUHQWꢅSDFNDJHꢅGUDZLQJVꢆꢅSOHDVHꢅVHHꢅWKHꢅ0LFURFKLSꢅ3DFNDJLQJꢅ6SHFLILFDWLRQꢅORFDWHGꢅDW
KWWSꢇꢈꢈZZZꢁPLFURFKLSꢁFRPꢈSDFNDJLQJ
8QLWV
'LPHQVLRQꢅ/LPLWV
0,//,0(7(56
120
0,1
0$;
1XPEHUꢅRIꢅ3LQV
3LWFK
2YHUDOOꢅ+HLJKW
6WDQGRII
7HUPLQDOꢅ7KLFNQHVV
2YHUDOOꢅ:LGWK
([SRVHGꢅ3DGꢅ:LGWK
2YHUDOOꢅ/HQJWK
([SRVHGꢅ3DGꢅ/HQJWK
7HUPLQDOꢅ:LGWK
&RUQHUꢅ3DG
1
ꢄꢌ
ꢀꢁꢐꢃꢅ%6&
ꢀꢁꢃꢀ
H
$
$ꢂ
ꢍ$ꢏꢎ
ꢀꢁꢉꢀ
ꢀꢁꢀꢀ
ꢀꢁꢐꢀ
ꢀꢁꢀꢃ
ꢀꢁꢀꢄ
ꢀꢁꢂꢄꢑꢅ5()
ꢐꢁꢀꢀꢅ%6&
ꢉꢁꢀꢀ
ꢐꢁꢀꢀꢅ%6&
ꢉꢁꢀꢀ
(
(ꢄ
'
'ꢄ
E
Eꢄ
/
.
ꢀꢁꢏꢃ
ꢀꢁꢄꢃ
ꢀꢁꢃꢃ
ꢀꢁꢄꢀ
ꢀꢁꢉꢀ
ꢀꢁꢉꢀ
ꢀꢁꢐꢀ
ꢊ
ꢀꢁꢉꢃ
ꢀꢁꢉꢃ
ꢀꢁꢐꢃ
ꢊ
7HUPLQDOꢅ/HQJWK
7HUPLQDOꢊWRꢊ([SRVHGꢅ3DG
Notes:
ꢂꢁ 3LQꢅꢂꢅYLVXDOꢅLQGH[ꢅIHDWXUHꢅPD\ꢅYDU\ꢆꢅEXWꢅPXVWꢅEHꢅORFDWHGꢅZLWKLQꢅWKHꢅKDWFKHGꢅDUHDꢁ
ꢄꢁ 3DFNDJHꢅLVꢅVDZꢅVLQJXODWHG
ꢏꢁ 'LPHQVLRQLQJꢅDQGꢅWROHUDQFLQJꢅSHUꢅ$60(ꢅ<ꢂꢉꢁꢃ0
%6&ꢇꢅ%DVLFꢅ'LPHQVLRQꢁꢅ7KHRUHWLFDOO\ꢅH[DFWꢅYDOXHꢅVKRZQꢅZLWKRXWꢅWROHUDQFHVꢁ
5()ꢇꢅ5HIHUHQFHꢅ'LPHQVLRQꢆꢅXVXDOO\ꢅZLWKRXWꢅWROHUDQFHꢆꢅIRUꢅLQIRUPDWLRQꢅSXUSRVHVꢅRQO\ꢁ
ꢉꢁ 2XWHUPRVWꢅSRUWLRQVꢅRIꢅFRUQHUꢅVWUXFWXUHVꢅPD\ꢅYDU\ꢅVOLJKWO\ꢁ
0LFURFKLSꢅ7HFKQRORJ\ꢅ'UDZLQJꢅꢅ&ꢀꢉꢊꢀꢄꢀꢋ%ꢅ6KHHWꢅꢄꢅRIꢅꢄ
2008-2014 Microchip Technology Inc.
DS70000318G-page 363
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Note: )RUꢅWKHꢅPRVWꢅFXUUHQWꢅSDFNDJHꢅGUDZLQJVꢆꢅSOHDVHꢅVHHꢅWKHꢅ0LFURFKLSꢅ3DFNDJLQJꢅ6SHFLILFDWLRQꢅORFDWHGꢅDW
KWWSꢇꢈꢈZZZꢁPLFURFKLSꢁFRPꢈSDFNDJLQJ
DS70000318G-page 364
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
2008-2014 Microchip Technology Inc.
DS70000318G-page 365
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
DS70000318G-page 366
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
2008-2014 Microchip Technology Inc.
DS70000318G-page 367
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
..ꢂꢃꢄꢅꢆꢇꢍꢎꢅꢏꢐꢊꢑꢇ0-ꢊꢋꢇ#ꢓꢅꢆꢇ$ꢎꢅꢐ1ꢅꢑꢉꢇꢕꢍ0ꢖꢇMꢇ2ꢘ)2ꢘ)2ꢇꢙꢙꢇꢚꢛꢆꢌ%ꢇꢀ*ꢘꢘꢇꢙꢙꢇꢜ0#$ꢍ
!ꢛꢐꢄ" 3ꢋꢉꢅ&ꢍꢈꢅ'ꢋ!&ꢅꢌ"ꢉꢉꢈꢄ&ꢅꢓꢆꢌ4ꢆꢑꢈꢅ#ꢉꢆ*ꢃꢄꢑ!(ꢅꢓꢇꢈꢆ!ꢈꢅ!ꢈꢈꢅ&ꢍꢈꢅꢔꢃꢌꢉꢋꢌꢍꢃꢓꢅꢂꢆꢌ4ꢆꢑꢃꢄꢑꢅꢐꢓꢈꢌꢃ%ꢃꢌꢆ&ꢃꢋꢄꢅꢇꢋꢌꢆ&ꢈ#ꢅꢆ&ꢅ
ꢍ&&ꢓ255***ꢁ'ꢃꢌꢉꢋꢌꢍꢃꢓꢁꢌꢋ'5ꢓꢆꢌ4ꢆꢑꢃꢄꢑ
D
D1
E
e
E1
N
b
NOTE 1
1 2 3
NOTE 2
α
A
c
φ
A2
β
A1
L
L1
6ꢄꢃ&!
ꢔꢚ99ꢚꢔ.ꢙ.ꢝꢐ
ꢒꢃ'ꢈꢄ!ꢃꢋꢄꢅ9ꢃ'ꢃ&!
ꢔꢚ7
7:ꢔ
ꢖꢖ
ꢕꢁ<ꢕꢅ1ꢐ,
M
ꢀꢁꢕꢕ
M
ꢔꢗ;
7"')ꢈꢉꢅꢋ%ꢅ9ꢈꢆ#!
9ꢈꢆ#ꢅꢂꢃ&ꢌꢍ
: ꢈꢉꢆꢇꢇꢅ8ꢈꢃꢑꢍ&
ꢔꢋꢇ#ꢈ#ꢅꢂꢆꢌ4ꢆꢑꢈꢅꢙꢍꢃꢌ4ꢄꢈ!!
ꢐ&ꢆꢄ#ꢋ%%ꢅꢅ
3ꢋꢋ&ꢅ9ꢈꢄꢑ&ꢍ
7
ꢈ
ꢗ
ꢗꢎ
ꢗꢀ
9
M
ꢀꢁꢎꢕ
ꢀꢁꢕꢘ
ꢕꢁꢀꢘ
ꢕꢁꢜꢘ
ꢕꢁꢛꢘ
ꢕꢁꢕꢘ
ꢕꢁꢖꢘ
ꢕꢁ?ꢕ
3ꢋꢋ&ꢓꢉꢃꢄ&
3ꢋꢋ&ꢅꢗꢄꢑꢇꢈ
9ꢀ
ꢀ
ꢀꢁꢕꢕꢅꢝ.3
-ꢁꢘꢟ
ꢕꢟ
ꢜꢟ
: ꢈꢉꢆꢇꢇꢅ>ꢃ#&ꢍ
: ꢈꢉꢆꢇꢇꢅ9ꢈꢄꢑ&ꢍ
.
ꢒ
.ꢀ
ꢒꢀ
ꢌ
ꢀꢎꢁꢕꢕꢅ1ꢐ,
ꢀꢎꢁꢕꢕꢅ1ꢐ,
ꢀꢕꢁꢕꢕꢅ1ꢐ,
ꢀꢕꢁꢕꢕꢅ1ꢐ,
M
ꢔꢋꢇ#ꢈ#ꢅꢂꢆꢌ4ꢆꢑꢈꢅ>ꢃ#&ꢍ
ꢔꢋꢇ#ꢈ#ꢅꢂꢆꢌ4ꢆꢑꢈꢅ9ꢈꢄꢑ&ꢍ
9ꢈꢆ#ꢅꢙꢍꢃꢌ4ꢄꢈ!!
9ꢈꢆ#ꢅ>ꢃ#&ꢍ
ꢔꢋꢇ#ꢅꢒꢉꢆ%&ꢅꢗꢄꢑꢇꢈꢅꢙꢋꢓ
ꢔꢋꢇ#ꢅꢒꢉꢆ%&ꢅꢗꢄꢑꢇꢈꢅ1ꢋ&&ꢋ'
ꢕꢁꢕꢛ
ꢕꢁ-ꢕ
ꢀꢀꢟ
ꢕꢁꢎꢕ
ꢕꢁꢖꢘ
ꢀ-ꢟ
)
ꢁ
ꢕꢁ-ꢜ
ꢀꢎꢟ
ꢀꢎꢟ
ꢂ
ꢀꢀꢟ
ꢀ-ꢟ
!ꢛꢐꢄꢏ"
ꢀꢁ ꢂꢃꢄꢅꢀꢅ ꢃ!"ꢆꢇꢅꢃꢄ#ꢈ$ꢅ%ꢈꢆ&"ꢉꢈꢅ'ꢆꢊꢅ ꢆꢉꢊ(ꢅ)"&ꢅ'"!&ꢅ)ꢈꢅꢇꢋꢌꢆ&ꢈ#ꢅ*ꢃ&ꢍꢃꢄꢅ&ꢍꢈꢅꢍꢆ&ꢌꢍꢈ#ꢅꢆꢉꢈꢆꢁ
ꢎꢁ ,ꢍꢆ'%ꢈꢉ!ꢅꢆ&ꢅꢌꢋꢉꢄꢈꢉ!ꢅꢆꢉꢈꢅꢋꢓ&ꢃꢋꢄꢆꢇAꢅ!ꢃBꢈꢅ'ꢆꢊꢅ ꢆꢉꢊꢁ
-ꢁ ꢒꢃ'ꢈꢄ!ꢃꢋꢄ!ꢅꢒꢀꢅꢆꢄ#ꢅ.ꢀꢅ#ꢋꢅꢄꢋ&ꢅꢃꢄꢌꢇ"#ꢈꢅ'ꢋꢇ#ꢅ%ꢇꢆ!ꢍꢅꢋꢉꢅꢓꢉꢋ&ꢉ"!ꢃꢋꢄ!ꢁꢅꢔꢋꢇ#ꢅ%ꢇꢆ!ꢍꢅꢋꢉꢅꢓꢉꢋ&ꢉ"!ꢃꢋꢄ!ꢅ!ꢍꢆꢇꢇꢅꢄꢋ&ꢅꢈ$ꢌꢈꢈ#ꢅꢕꢁꢎꢘꢅ''ꢅꢓꢈꢉꢅ!ꢃ#ꢈꢁ
ꢖꢁ ꢒꢃ'ꢈꢄ!ꢃꢋꢄꢃꢄꢑꢅꢆꢄ#ꢅ&ꢋꢇꢈꢉꢆꢄꢌꢃꢄꢑꢅꢓꢈꢉꢅꢗꢐꢔ.ꢅ0ꢀꢖꢁꢘꢔꢁ
1ꢐ,2 1ꢆ!ꢃꢌꢅꢒꢃ'ꢈꢄ!ꢃꢋꢄꢁꢅꢙꢍꢈꢋꢉꢈ&ꢃꢌꢆꢇꢇꢊꢅꢈ$ꢆꢌ&ꢅ ꢆꢇ"ꢈꢅ!ꢍꢋ*ꢄꢅ*ꢃ&ꢍꢋ"&ꢅ&ꢋꢇꢈꢉꢆꢄꢌꢈ!ꢁ
ꢝ.32 ꢝꢈ%ꢈꢉꢈꢄꢌꢈꢅꢒꢃ'ꢈꢄ!ꢃꢋꢄ(ꢅ"!"ꢆꢇꢇꢊꢅ*ꢃ&ꢍꢋ"&ꢅ&ꢋꢇꢈꢉꢆꢄꢌꢈ(ꢅ%ꢋꢉꢅꢃꢄ%ꢋꢉ'ꢆ&ꢃꢋꢄꢅꢓ"ꢉꢓꢋ!ꢈ!ꢅꢋꢄꢇꢊꢁ
ꢔꢃꢌꢉꢋꢌꢍꢃꢓ ꢙꢈꢌꢍꢄꢋꢇꢋꢑꢊ ꢒꢉꢆ*ꢃꢄꢑ ,ꢕꢖꢞꢕꢜ?1
DS70000318G-page 368
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2008-2014 Microchip Technology Inc.
DS70000318G-page 369
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
44-Terminal Very Thin Leadless Array Package (TL) – 6x6x0.9 mm Body
With Exposed Pad [VTLA]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
A
B
E
N
NOTE 1
1
2
(DATUM B)
2X
0.20 C
2X
(DATUM A)
0.20 C
TOP VIEW
0.10 C
0.08 C
A1
C
A
SEATING
PLANE
SIDE VIEW
0.10
23
C A B
D2
11
22
0.10
C A
10
DETAIL A
(NE-1) X e
E2
2
1
32
N
33
44X K
(ND-1) X e
BOTTOM VIEW
Microchip Technology Drawing C04-157D Sheet 1 of 2
DS70000318G-page 370
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
44-Terminal Very Thin Leadless Array Package (TL) – 6x6x0.9 mm Body
With Exposed Pad [VTLA]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
(DATUM
e/2
A OR B)
e
44X b
0.10
0.05
C A B
C
44X L
DETAIL A
Units
MILLIMETERS
Dimension Limits
N
MIN
NOM
44
MAX
Number of Terminals
Number of Terminals per Side
Number of Terminals per Side
Pitch
Overall Height
Standoff
Overall Width
Exposed Pad Width
Overall Length
Exposed Pad Length
Terminal Width
Terminal Length
Terminal-to-Exposed Pad
ND
NE
e
A
A1
E
E2
D
D2
b
12
10
0.50 BSC
0.90
-
6.00 BSC
4.55
6.00 BSC
4.55
0.25
0.25
-
0.80
0.025
1.00
0.075
4.40
4.70
4.40
0.20
0.20
0.20
4.70
0.30
0.30
-
L
K
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Package is saw singulated.
3. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-157D Sheet 2 of 2
2008-2014 Microchip Technology Inc.
DS70000318G-page 371
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
DS70000318G-page 372
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Revision B (June 2008)
APPENDIX A: REVISION HISTORY
This revision includes minor typographical and
formatting changes throughout the data sheet text. In
addition, redundant information was removed that is
now available in the respective chapters of the
dsPIC33F/PIC24H Family Reference Manual, which
can be obtained from the Microchip web site
(www.microchip.com).
Revision A (January 2008)
This is the initial revision of this document.
The major changes are referenced by their respective
section in the following table.
TABLE A-1:
MAJOR SECTION UPDATES
Section Name
Update Description
“High-Performance, 16-bit Digital
Signal Controllers”
Moved location of Note 1 (RPn pin) references (see “Pin Diagrams”).
Section 3.0 “Memory Organization” Updated CPU Core Register map SFR reset value for CORCON (see
Table 3-1).
Removed Interrupt Controller Register Map SFR IPC29 and updated reset
values for IPC0, IPC1, IPC14, IPC16, IPC23, IPC24, IPC27, and IPC28 (see
Table 3-5).
Removed Interrupt Controller Register Map SFR IPC24 and IPC29 and
updated reset values for IPC0, IPC1, IPC2, IPC14, IPC16, IPC23, IPC27,
and IPC28 (see Table 3-6).
Removed Interrupt Controller Register Map SFR IPC24 and updated reset
values for IPC1, IPC2, IPC4, IPC14, IPC16, IPC23, IPC24, IPC27, and
IPC28 (see Table 3-7).
Updated Interrupt Controller Register Map SFR reset values for IPC1,
IPC14, IPC16, IPC23, IPC24, IPC27, and IPC28 (see Table 3-8).
Updated Interrupt Controller Register Map SFR reset values for IPC1,
IPC14, IPC16, IPC23, IPC24, IPC25, IPC26, IPC27, IPC28, and IPC29 (see
Table 3-9).
Updated Interrupt Controller Register Map SFR reset values for IPC1, IPC4,
IPC14, IPC16, IPC23, IPC24, IPC25, IPC26, IPC27, IPC28, and IPC29 (see
Table 3-10).
Added SFR definitions for RPOR16 and RPOR17 (see Table 3-34,
Table 3-35, and Table 3-36).
Updated bit definitions for PORTA, PORTB, and PORTC SFRs (ODCA,
ODCB, and ODCC) (see Table 3-37, Table 3-38, Table 3-39, and
Table 3-40).
Updated bit definitions and reset value for System Control Register map
SFR CLKDIV (see Table 3-41).
Added device-specific information to title of PMD Register Map (see
Table 3-47).
Added device-specific PMD Register Maps (see Table 3-46, Table 3-45, and
Table 3-43).
2008-2014 Microchip Technology Inc.
DS70000318G-page 373
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE A-1:
MAJOR SECTION UPDATES (CONTINUED)
Section Name
Update Description
Section 7.0 “Oscillator
Configuration”
Removed the first sentence of the third clock source item (External Clock) in
Section 7.1.1 “System Clock sources”
Updated the default bit values for DOZE and FRCDIV in the Clock Divisor
Register (see Register 7-2).
Section 8.0 “Power-Saving
Features”
Added the following six registers:
• “PMD1: Peripheral Module Disable Control Register 1”
• “PMD2: Peripheral Module Disable Control Register 2”
• “PMD3: Peripheral Module Disable Control Register 3”
• “PMD4: Peripheral Module Disable Control Register 4”
• “PMD6: Peripheral Module Disable Control Register 6”
• “PMD7: Peripheral Module Disable Control Register 7”
Section 9.0 “I/O Ports”
Added paragraph and Table 9-1 to Section 9.1.1 “Open-Drain
Configuration”, which provides details on I/O pins and their functionality.
Removed 9.1.2 “5V Tolerance”.
Updated MUX range and removed virtual pin details in Figure 9-2.
Updated PWM Input Name descriptions in Table 9-1.
Added Section 9.4.2.3 “Virtual Pins”.
Updated bit values in all Peripheral Pin Select Input Registers (see
Register 9-1 through Register 9-14).
Updated bit name information for Peripheral Pin Select Output Registers
RPOR16 and RPOR17 (see Register 9-30 and Register 9-31).
Added the following two registers:
• “RPOR16: Peripheral Pin Select Output Register 16”
• “RPOR17: Peripheral Pin Select Output Register 17”
Removed the following sections:
• 9.4.2 “Available Peripherals”
• 9.4.3.2 “Virtual Input Pins”
• 9.4.3.4 “Peripheral Mapping”
• 9.4.5 “Considerations for Peripheral Pin Selection” (and all subsections)
Added Note 1 (remappable pin reference) to Figure 14-1.
Section 14.0 “High-Speed PWM”
Added Note 2 (Duty Cycle resolution) to PWM Master Duty Cycle Register
(Register 14-5), PWM Generator Duty Cycle Register (Register 14-7), and
PWM Secondary Duty Cycle Register (Register 14-8).
Added Note 2 and Note 3 and updated bit information for CLSRC and
FLTSRC in the PWM Fault Current-Limit Control Register (Register 14-15).
Section 15.0 “Serial Peripheral
Interface (SPI)”
Removed the following sections, which are now available in the related
section of the dsPIC33F/PIC24H Family Reference Manual:
• 15.1 “Interrupts”
• 15.2 “Receive Operations”
• 15.3 “Transmit Operations”
• 15.4 “SPI Setup” (retained Figure 15-1: SPI Module Block Diagram)
DS70000318G-page 374
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE A-1:
MAJOR SECTION UPDATES (CONTINUED)
Section Name
Update Description
Section 16.0 “Inter-Integrated
Circuit (I2C™)”
Removed the following sections, which are now available in the related
section of the dsPIC33F/PIC24H Family Reference Manual:
• 16.3 “I2C Interrupts”
• 16.4 “Baud Rate Generator” (retained Figure 16-1: I2C Block Diagram)
• 16.5 “I2C Module Addresses
• 16.6 “Slave Address Masking”
• 16.7 “IPMI Support”
• 16.8 “General Call Address Support”
• 16.9 “Automatic Clock Stretch”
• 16.10 “Software Controlled Clock Stretching (STREN = 1)”
• 16.11 “Slope Control”
• 16.12 “Clock Arbitration”
• 16.13 “Multi-Master Communication, Bus Collision, and Bus Arbitration
Section 17.0 “Universal
Removed the following sections, which are now available in the related
Asynchronous Receiver Transmitter section of the dsPIC33F/PIC24H Family Reference Manual:
(UART)”
• 17.1 “UART Baud Rate Generator”
• 17.2 “Transmitting in 8-bit Data Mode
• 17.3 “Transmitting in 9-bit Data Mode
• 17.4 “Break and Sync Transmit Sequence”
• 17.5 “Receiving in 8-bit or 9-bit Data Mode”
• 17.6 “Flow Control Using UxCTS and UxRTS Pins”
• 17.7 “Infrared Support”
Removed IrDA references and Note 1, and updated the bit and bit value
descriptions for UTXINV (UxSTA<14>) in the UARTx Status and Control
Register (see Register 17-2).
Section 18.0 “High-Speed 10-bit
Updated bit value information for Analog-to-Digital Control Register (see
Analog-to-Digital Converter (ADC)” Register 18-1).
Updated TRGSRC6 bit value for Timer1 period match in the Analog-to-
Digital Convert Pair Control Register 3 (see Register 18-8).
2008-2014 Microchip Technology Inc.
DS70000318G-page 375
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE A-1:
MAJOR SECTION UPDATES (CONTINUED)
Section Name
Update Description
Section 23.0 “Electrical
Characteristics”
Updated Typ values for Thermal Packaging Characteristics (Table 23-3).
Removed Typ value for DC Temperature and Voltage Specifications
Parameter DC12 (Table 23-4).
Updated all Typ values and conditions for DC Characteristics: Operating
Current (IDD), updated last sentence in Note 2 (Table 23-5).
Updated all Typ values for DC Characteristics: Idle Current (IIDLE) (see
Table 23-6).
Updated all Typ values for DC Characteristics: Power Down Current (IPD)
(see Table 23-7).
Updated all Typ values for DC Characteristics: Doze Current (IDOZE) (see
Table 23-8).
Added Note 4 (reference to new table containing digital-only and analog pin
information, as well as Current Sink/Source capabilities) in the I/O Pin Input
Specifications (Table 23-9).
Updated Max value for BOR electrical characteristics Parameter BO10 (see
Table 23-11).
Swapped Min and Typ values for Program Memory Parameters D136 and
D137 (Table 23-12).
Updated Typ values for Internal RC Accuracy Parameter F20 and added
Extended temperature range to table heading (see Table 23-19).
Removed all values for Reset, Watchdog Timer, Oscillator Start-up Timer,
and Power-up Timer Parameter SY20 and updated conditions, which now
refers to Section 20.4 “Watchdog Timer (WDT)” and LPRC Parameter
F21a (see Table 23-22).
Added specifications to High-Speed PWM Module Timing Requirements for
Tap Delay (Table 23-29).
Updated Min and Max values for 10-bit High-Speed Analog-to-Digital
Module Parameters AD01 and AD11 (see Table 23-36).
Updated Max value and unit of measure for DAC AC Specification (see
Table 23-40).
DS70000318G-page 376
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Revision C and D (March 2009)
This revision includes minor typographical and
formatting changes throughout the data sheet text.
Global changes include:
• Changed all instances of OSCI to OSC1 and
OSCO to OSC2
• Changed all instances of PGCx/EMUCx and
PGDx/EMUDx (where x = 1, 2, or 3) to PGECx
and PGEDx
• Changed all instances of VDDCORE and VDDCORE/
VCAP to VCAP/VDDCORE
Other major changes are referenced by their respective
section in the following table.
TABLE A-2:
MAJOR SECTION UPDATES
Section Name
Update Description
“High-Performance, 16-bit Digital
Signal Controllers”
Added “Application Examples” to list of features
Updated all pin diagrams to denote the pin voltage tolerance (see “Pin
Diagrams”).
Added Note 2 to the 28-Pin QFN-S and 44-Pin QFN pin diagrams, which
references pin connections to VSS.
Section 1.0 “Device Overview”
Added ACMP1-ACMP4 pin names and Peripheral Pin Select capability
column to Pinout I/O Descriptions (see Table 1-1).
Section 2.0 “Guidelines for Getting Added new section to the data sheet that provides guidelines on getting
Started with 16-bit Digital Signal
Controllers”
started with 16-bit Digital Signal Controllers.
Section 3.0 “CPU”
Updated CPU Core Block Diagram with a connection from the DSP Engine
to the Y Data Bus (see Figure 3-1).
Vertically extended the X and Y Data Bus lines in the DSP Engine Block
Diagram (see Figure 3-3).
Section 4.0 “Memory Organization” Updated Reset value for ADCON in Table 4-25.
Removed reference to dsPIC33FJ06GS102 devices in the PMD Register
Map and updated bit definitions for PMD1 and PMD6, and removed PMD7
(see Table 4-43).
Added a new PMD Register Map, which references dsPIC33FJ06GS102
devices (see Table 4-44).
Updated RAM stack address and SPLIM values in the third paragraph of
Section 4.2.6 “Software Stack”
Removed Section 4.2.7 “Data Ram Protection Feature”.
Section 5.0 “Flash Program
Memory”
Updated Section 5.3 “Programming Operations” with programming time
formula.
2008-2014 Microchip Technology Inc.
DS70000318G-page 377
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE A-2:
MAJOR SECTION UPDATES (CONTINUED)
Section Name
Update Description
Section 8.0 “Oscillator
Configuration”
Added Note 2 to the Oscillator System Diagram (see Figure 8-1).
Added a paragraph regarding FRC accuracy at the end of Section 8.1.1
“System Clock Sources”.
Added Note 1 and Note 2 to the OSCON register (see Register ).
Added Note 1 to the OSCTUN register (see Register 8-4).
Added Note 3 to Section 8.4.2 “Oscillator Switching Sequence”.
Section 10.0 “I/O Ports”
Removed Table 9-1 and added reference to pin diagrams for I/O pin
availability and functionality.
Added paragraph on ADPCFG register default values to Section 10.3
“Configuring Analog Port Pins”.
Added Note box regarding PPS functionality with input mapping to
Section 10.6.2.1 “Input Mapping”.
Section 15.0 “High-Speed PWM”
Updated Note 2 in the PTCON register (see Register 15-1).
Added Note 4 to the PWMCONx register (see Register 15-6).
Updated Notes for the PHASEx and SPHASEx registers (see Register 15-9
and Register 15-10, respectively).
Section 16.0 “Serial Peripheral
Interface (SPI)”
Added Note 2 and Note 3 to the SPIxCON1 register (see Register 16-2).
Section 18.0 “Universal
Asynchronous Receiver Transmitter
(UART)”
Updated the Notes in the UxMode register (see Register 18-1).
Updated the UTXINV bit settings in the UxSTA register and added Note 1
(see Register 18-2).
Section 19.0 “High-Speed 10-bit
Updated the SLOWCLK and ADCS<2:0> bit settings and updated Note 1in
Analog-to-Digital Converter (ADC)” the ADCON register (see Register 19-1).
Removed all notes in the ADPCFG register and replaced them with a single
note (see Register 19-4).
Updated the SWTRGx bit settings in the ADCPCx registers (see
Register 19-5, Register 19-6, Register 19-7, and Register 19-8).
DS70000318G-page 378
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE A-2:
MAJOR SECTION UPDATES (CONTINUED)
Section Name
Update Description
Section 24.0 “Electrical
Characteristics”
Updated Typical values for Thermal Packaging Characteristics (see
Table 24-3).
Updated Min and Max values for Parameter DC12 (RAM Data Retention
Voltage) and added Note 4 (see Table 24-4).
Updated Characteristics for I/O Pin Input Specifications (see Table 24-9).
Added ISOURCE to I/O Pin Output Specifications (see Table 24-10).
Updated Program Memory values for Parameters 136, 137, and 138
(renamed to 136a, 137a, and 138a), added Parameters 136b, 137b, and
138b, and added Note 2 (see Table 24-12).
Added Parameter OS42 (GM) to the External Clock Timing Requirements
(see Table 24-16).
Updated Conditions for symbol TPDLY (Tap Delay) and added symbol ACLK
(PWM Input Clock) to the High-Speed PWM Module Timing Requirements
(see Table 24-29).
Updated Parameters AD01 and AD02 in the 10-bit High-Speed Analog-to-
Digital Module Specifications (see Table 24-36).
Updated Parameters AD50b, AD55b, and AD56b, and removed
Parameters AD57b and AD60b from the 10-bit High-Speed Analog-to-Digital
Module Timing Requirements (see Table 24-37).
2008-2014 Microchip Technology Inc.
DS70000318G-page 379
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Revision E (December 2009)
The revision includes the following global update:
• Added Note 2 to the shaded table that appears at
the beginning of each chapter. This new note
provides information regarding the availability of
registers and their associated bits
This revision also includes minor typographical and
formatting changes throughout the data sheet text.
All other major changes are referenced by their
respective section in the following table.
TABLE A-3:
MAJOR SECTION UPDATES
Section Name
Update Description
“16-bit Microcontrollers and Digital
Signal Controllers (up to 16-Kbyte
Flash and up to 2-Kbyte SRAM) with
High-Speed PWM, ADC and
Comparators”
Changed CN6 to CN5 on pin 16 of dsPIC33FJ16GS502 28-pin SPDIP,
SOIC pin diagram.
Section 2.0 “Guidelines for Getting
Started with 16-bit Digital Signal
Controllers”
Removed the 10 Ohm resistor from Figure 2-1.
Section 4.0 “Memory Organization”
Renamed bit 13 of the REFOCON SFR in the System Control Register
Map from ROSIDL to ROSSLP and changed the All Resets value from
‘0000’ to ‘2300’ for the ACLKCON SFR (see 4-41).
Section 8.0 “Oscillator Configuration” Updated the default reset values from R/W-0 to R/W-1 for the SELACLK
and APSTSCLR<2:0> bits in the ACLKCON register (see Register 8-5).
Renamed the ROSIDL bit to ROSSLP in the REFOCON register (see
Register 8-6).
Section 9.0 “Power-Saving Features” Updated the last paragraph of Section 9.2.2 “Idle Mode” to clarify when
instruction execution begins.
Added Note 1 to the PMD1 register (see Register 9-1).
Section 10.0 “I/O Ports”
Changed the reference to digital-only pins to 5V tolerant pins in the
second paragraph of Section 10.2 “Open-Drain Configuration”.
Section 15.0 “High-Speed PWM”
Updated the smallest pulse width value from 0x0008 to 0x0009 in Note 1
of the shaded note that follows the MDC register (see Register 15-5).
Updated the smallest pulse width value from 0x0008 to 0x0009 and the
maximum pulse width value from 0x0FFEF to 0x0008 in Note 2 of the
shaded note that follows the PDCx and SDCx registers (see Register 15-7
and Register 15-8).
Added Note 2 and updated the FLTDAT<1:0> and CLDAT<1:0> bits,
changing the word ‘data’ to ‘state’ in the IOCONx register (see
Register 15-14).
Section 18.0 “Universal
Asynchronous Receiver Transmitter
(UART)”
Updated the two baud rate range features to: 10 Mbps to 38 bps at 40
MIPS.
DS70000318G-page 380
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE A-3:
MAJOR SECTION UPDATES (CONTINUED)
Section Name
Update Description
Section 19.0 “High-Speed 10-bit
Updated Note 1 in the ADCPC0 register (see Register 19-5).
Analog-to-Digital Converter (ADC)”
Updated Note 3 in the ADCPC1 register (see Register 19-6).
Updated Note 2 in the ADCPC2 and ADCPC3 registers (see Register 19-
7 and Register 19-8).
Section 21.0 “Special Features”
Updated the second paragraph and removed the fourth paragraph in
Section 21.1 “Configuration Bits”.
Updated the Device Configuration Register Map (see Table 21-1).
Section 24.0 “Electrical
Characteristics”
Updated the Absolute Maximum Ratings for high temperature and added
Note 4.
Updated Idle Current (IIDLE) Typical values in Table 24-6.
Updated the Typ and Max values for Parameter DI50 in the I/O Pin Input
Specifications table (see Table 24-9).
Updated the Typ and Max values for Parameters DO10 and DO27 and the
Min and Typ values for Parameter DO20 in the I/O Pin Output
Specifications (see Table 24-10).
Added parameter numbers to the Auxiliary PLL Clock Timing
Specifications (see Table 24-18).
Added parameters numbers and updated the Internal RC Accuracy Min,
Typ, and Max values (see Table 24-19 and Table 24-20).
Added parameter numbers, Note 2, updated the Min and Typ parameter
values for MP31 and MP32, and removed the conditions for MP10 and
MP11 in the High-Speed PWM Module Timing Requirements (see
Table 24-29).
Updated the SPIx Module Slave Mode (CKE = 1) Timing Characteristics
(see Table 24-14).
Added Parameter IM51 to the I2Cx Bus Data Timing Requirements
(Master Mode) (see Table 24-34).
Updated the Max value for Parameter AD33 in the 10-bit High-Speed
Analog-to-Digital Module Specifications (see Table 24-36).
Updated the titles and added parameter numbers to the Comparator and
DAC Module Specifications (see Table 24-38 and Table 24-39) and the
DAC Output Buffer Specifications (see Table 24-40).
2008-2014 Microchip Technology Inc.
DS70000318G-page 381
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Revision F (January 2012)
All occurrences of VDDCORE have been removed
throughout the document.
This revision also includes minor typographical and
formatting changes throughout the data sheet text.
All other major changes are referenced by their
respective section in the following table.
TABLE A-4:
MAJOR SECTION UPDATES
Section Name
Update Description
“16-Bit Digital Signal Controllers (up Added the VTLA package to the dsPIC33FJ16GS404 and
to 16-Kbyte Flash and up to 2-Kbyte dsPIC33FJ16GS504 devices (see TABLE 1: “dsPIC33FJ06GS101/X02
SRAM) with High-Speed PWM, ADC and dsPIC33FJ16GSX02/X04 Controller Families”).
and Comparators”
Added the “Referenced Sources” section.
The following updates were made to the “Pin Diagrams” section:
• Added 5V tolerant pin shading to pins 24-26 in the 28-pin SPDIP, SOIC
package for the dsPIC33FJ16GS402
• Updated pin 31 of the 44-pin QFN package for the dsPIC33FJ16GS404
• Added VTLA pin diagrams for the dsPIC33FJ16GS404 and
dsPIC33FJ16GS504 devices
Section 1.0 “Device Overview”
Removed the Precision Band Gap Reference from the device block diagram
(see Figure 1-1).
Updated the Pinout I/O Descriptions for AVDD, and AVSS (see Table 1-1).
Section 2.0 “Guidelines for Getting Updated the Minimum Recommended Connection (see Figure 2-1).
Started with 16-bit Digital Signal
Controllers”
Section 8.0 “Oscillator
Configuration”
Updated the Oscillator System Diagram (see Figure 8-1).
Added auxiliary clock configuration restrictions in Section 8.2 “Auxiliary
Clock Generation”.
Updated or added notes regarding register reset on a POR
(see Register 8-1 through Register 8-5).
Section 19.0 “High-Speed 10-bit
Added Note 2 to ADCON: Analog-to-Digital Control Register
Analog-to-Digital Converter (ADC)” (see Register 19-1).
Removed all notes from ADSTAT: Analog-to-Digital Status Register
(see Register 19-2).
Section 20.0 “High-Speed Analog
Comparator”
Updated the Comparator Module Block Diagram (see Figure 20-1).
Section 21.0 “Special Features”
Add a new paragraph at the beginning of Section 21.1 “Configuration
Bits”.
Added the RTSP Effect column to the dsPIC33F Configuration Bits
Description table (see Table 21-2).
Updated the Connections for the On-chip Voltage Regulator diagram
(see Figure 21-1).
Updated the first paragraph of Section 21.7 “In-Circuit Debugger”.
DS70000318G-page 382
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE A-4:
MAJOR SECTION UPDATES (CONTINUED)
Update Description
Updated the Absolute Maximum Ratings.
Section Name
Section 24.0 “Electrical
Characteristics”
Updated the Operating MIPS vs. Voltage (see Table 24-1).
Updated Parameter DC10 and Note 4, and removed Parameter DC18 from
the DC Temperature and Voltage Specifications (see Table 24-4).
Updated Note 2 in the IDD Operating Current specification (see Table 24-5).
Updated all Typical values and Note 2 in the IIDLE Operating Current
specification (see Table 24-6).
Updated Typical values for Parameters DC60d, DC60a, DC60b, and
DC60c, and Note 2 in the IPD Operating Current specification
(see Table 24-7).
Added all Typical values and Note 2 in the IDOZE Operating Current
specification (see Table 24-8).
Updated Parameters DI19 and DI50, added Parameters DI128, DI129,
DI60a, DI60b, and DI60c, and removed Parameter DI57 in the I/O Pin Input
Specifications (see Table 24-9).
Revised all I/O Pinout Output Specifications (see Table 24-10).
Added Notes 2 and 3 to the BOR Electrical Characteristics (see Table 24-
11).
Added Note 1 to Internal Voltage Regulator Specifications
(see Table 24-13).
Updated the External Clock Timing diagram (see Figure 24-2).
Added Note 2 to the PLL Clock Timing Specifications (see Table 24-17).
Removed Note 2 from the Internal FRC Accuracy (see Table 24-19).
Updated Parameters DO31 and DO32 in the I/O Timing Requirements
(see Table 24-21).
Updated the External Clock Timing Requirements for Timer1, Timer2, and
Timer3 (see Table 24-23, Table 24-24, and Table 24-25, respectively).
Updated Parameters OC15 and OC20 in the Simple OC/PWM Mode Timing
Requirements (see Table 24-28).
Revised all SPIx Module Timing Characteristics diagrams and all Timing
Requirements (see Figure 24-11 through Figure 24-18 and Table 24-30
through Table 24-37, respectively).
Added Note 2 to the 10-bit High-Speed ADC Module Specifications (see
Table 24-40).
Added Note 2 to the 10-bit High-Speed ADC Module Timing Requirements
(see Table 24-41).
Added Note 2 to the Comparator Module Specifications (see Table 24-42).
Added Parameter DA08 and Note 2 in the DAC Module Specifications
(see Table 24-43).
Updated Parameter DA16 and Note 2 in the DAC Output Buffer DC
Specifications
(see Table 24-44).
2008-2014 Microchip Technology Inc.
DS70000318G-page 383
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
TABLE A-4:
MAJOR SECTION UPDATES (CONTINUED)
Section Name
Update Description
Section 26.0 “50 MIPS Electrical
Characteristics”
Added new chapter in support of 50 MIPS devices.
Section 27.0 “DC and AC Device
Characteristics Graphs”
Added new chapter.
Section 28.0 “Packaging
Information”
Added 44-pin VTLA package marking information and diagrams (see
Section 28.1 “Package Marking Information” and Section 28.2
“Package Details”, respectively).
“Product Identification System”
Added the TL package definition.
DS70000318G-page 384
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Revision G (May 2014)
The values for the TUN<5:0> bits in Register 8-4
(OSCTUN) have changed.
The DC Characteristics Idle Current values in
Section 24.0 “Electrical Characteristics” have been
updated.
The timer specifications in Section 26.0 “50 MIPS
Electrical Characteristics” have been removed.
All diagrams in Section 28.0 “Packaging Information”
have been updated.
Minor text edits have been applied throughout the
document.
2008-2014 Microchip Technology Inc.
DS70000318G-page 385
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 386
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
INDEX
Code Examples
Erasing a Program Memory Page .............................. 87
A
AC Characteristics ............................................ 300, 338, 345
Internal FRC Accuracy.............................................. 303
Internal LPRC Accuracy............................................ 303
Load Conditions................................................ 300, 338
ADC
Control Registers ...................................................... 246
Functionality.............................................................. 239
Arithmetic Logic Unit (ALU)................................................. 38
Assembler
Initiating a Programming Sequence ........................... 88
Loading Write Buffers................................................. 88
Port Write/Read........................................................ 156
PWRSAV Instruction Syntax .................................... 147
Code Protection........................................................ 267, 273
CodeGuard Security ......................................................... 267
Configuration Bits ............................................................. 267
Description................................................................ 268
Configuration Register Map.............................................. 267
Configuring Analog Port Pins............................................ 156
CPU
MPASM Assembler................................................... 284
Auxiliary Clock Generation................................................ 138
Control Registers........................................................ 34
CPU Clocking System ...................................................... 136
PLL Configuration..................................................... 137
Selection................................................................... 136
Sources .................................................................... 136
Customer Change Notification Service............................. 392
Customer Notification Service .......................................... 392
Customer Support............................................................. 392
B
Barrel Shifter ....................................................................... 42
Bit-Reversed Addressing .................................................... 76
Example...................................................................... 77
Implementation ........................................................... 76
Sequence Table (16-Entry)......................................... 77
Block Diagrams
16-Bit Timer1 Module................................................ 183
Connections for On-Chip Voltage Regulator............. 270
DSP Engine ................................................................ 39
dsPIC33F06GS101 Devices with 1 SAR .................. 240
dsPIC33F06GS102 Devices with 1 SAR .................. 241
dsPIC33F06GS202 Devices with 1 SAR .................. 242
dsPIC33F16GS402/404 Devices with 1 SAR ........... 243
dsPIC33F16GS502 Devices with 2 SARs ................ 244
dsPIC33F16GS504 Devices with 2 SARs ................ 245
dsPIC33FJ06GS101/X02 and
D
DAC .................................................................................. 264
Output Range ........................................................... 264
Data Accumulators and Adder/Subtracter .......................... 40
Data Space Write Saturation...................................... 42
Overflow and Saturation............................................. 40
Round Logic ............................................................... 41
Write Back .................................................................. 41
Data Address Space........................................................... 45
Alignment.................................................................... 45
Memory Map for dsPIC33FJ06GS101/102 Devices
with 256 Bytes of RAM ....................................... 46
Memory Map for dsPIC33FJ06GS202 Device
with 1-Kbyte RAM............................................... 47
Memory Map for dsPIC33FJ16GS402/404/502/504
Devices with 2-Kbyte RAM................................. 48
Near Data Space........................................................ 45
Software Stack ........................................................... 73
Width .......................................................................... 45
Data Addressing
dsPIC33FJ16GSX02/X04 ................................... 18
dsPIC33FJ06GS101/X02 and
dsPIC33FJ16GSX02/X04 CPU Core.................. 32
High-Speed Analog Comparator............................... 263
I2CX Module ............................................................. 226
Input Capture x ......................................................... 191
Multiplexing of Remappable Output for RPn............. 159
Oscillator System...................................................... 135
Output Compare x Module........................................ 193
Partitioned Output Pair, Complementary
PWM Mode ....................................................... 200
PLL............................................................................ 137
Remappable MUX Input for U1RX............................ 157
Reset System.............................................................. 89
Shared Port Structure ............................................... 155
Simplified Conceptual High-Speed PWM ................. 199
SPIx Module.............................................................. 219
Timer2/3 (32-Bit)....................................................... 187
Type B Timer ............................................................ 185
Type C Timer ............................................................ 185
UART1 ...................................................................... 233
Watchdog Timer (WDT)............................................ 271
Brown-out Reset (BOR)...................................... 94, 267, 270
Overview..................................................................... 31
DC and AC Characteristics
Graphs and Tables................................................... 347
DC Characteristics.................................................... 288, 342
Doze Current (IDOZE)........................................ 294, 344
High Temperature..................................................... 334
I/O Pin Input Specifications ...................................... 295
I/O Pin Output Specifications............................ 297, 336
Idle Current (IIDLE)............................................ 292, 343
Operating Current (IDD) .................................... 290, 342
Operating MIPS vs. Voltage ..................... 288, 334, 342
Power-Down Current (IPD)................................ 293, 335
Program Memory.............................................. 299, 337
Temperature and Voltage......................................... 334
Temperature and Voltage Specifications.................. 289
Thermal Operating Conditions.................................. 334
C
C Compilers
MPLAB XC Compilers............................................... 284
Clock Switching................................................................. 146
Enabling.................................................................... 146
Sequence.................................................................. 146
2008-2014 Microchip Technology Inc.
DS70000318G-page 387
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Demo/Development Boards, Evaluation and
Instruction Addressing Modes ............................................ 73
File Register Instructions ............................................ 73
Fundamental Modes Supported ................................. 74
MAC Instructions ........................................................ 74
MCU Instructions ........................................................ 73
Move and Accumulator Instructions............................ 74
Other Instructions ....................................................... 74
Instruction Set
Overview................................................................... 278
Summary .................................................................. 275
Instruction-Based Power-Saving Modes........................... 147
Idle............................................................................ 148
Sleep ........................................................................ 147
Interfacing Program and Data Memory Spaces.................. 78
Internal RC Oscillator
Starter Kits ................................................................286
Development Support .......................................................283
Third-Party Tools ......................................................286
Doze Mode........................................................................148
DSP Engine.........................................................................38
Multiplier......................................................................40
E
Electrical Characteristics...................................................287
50 MIPS ....................................................................341
AC .............................................................................338
AC Characteristics and
Timing Parameters.................................... 300, 345
BOR ..........................................................................298
Equations
Device Operating Frequency ....................................136
FOSC Calculation.......................................................137
Maximum Row Write Time..........................................84
Minimum Row Write Time...........................................84
Programming Time .....................................................84
XT with PLL Mode Example......................................137
Errata ..................................................................................14
External Reset (EXTR)........................................................95
Use with WDT........................................................... 271
Internet Address ............................................................... 392
Interrupts
Alternate Interrupt Vector Table (AIVT) ...................... 97
Control and Status Registers.................................... 100
IECx.................................................................. 100
IFSx .................................................................. 100
INTCON1.......................................................... 100
INTCON2.......................................................... 100
INTTREG.......................................................... 100
IPCx.................................................................. 100
Interrupt Vector Table (IVT)........................................ 97
Reset Sequence ......................................................... 97
Setup Procedures..................................................... 134
Initialization....................................................... 134
Interrupt Disable ............................................... 134
Interrupt Service Routine.................................. 134
Trap Service Routine........................................ 134
Interrupts Coincident with Power Save Instructions ......... 148
F
Fail-Safe Clock Monitor (FSCM) .......................................146
Flash Program Memory.......................................................83
Control Registers ........................................................84
Operations ..................................................................84
Programming Algorithm ..............................................87
RTSP Operation..........................................................84
Table Instructions........................................................83
Flexible Configuration .......................................................267
G
J
Guidelines for Getting Started with 16-Bit DSCs.................21
JTAG Boundary Scan Interface........................................ 267
JTAG Interface.................................................................. 272
H
M
High-Speed 10-Bit Analog-to-Digital
Converter (ADC) .......................................................239
High-Speed Analog Comparator.......................................263
Digital Logic ..............................................................264
Input Range ..............................................................264
Interaction with I/O Buffers........................................264
High-Speed PWM .............................................................197
Control Registers ......................................................200
High-Temperature Electrical Characteristics.....................333
Memory Organization ......................................................... 43
Microchip Internet Web Site.............................................. 392
Modulo Addressing............................................................. 75
Applicability................................................................. 76
Operation Example..................................................... 75
Start and End Address ............................................... 75
W Address Register Selection.................................... 75
MPLAB Assembler, Linker, Librarian................................ 284
MPLAB ICD 3 In-Circuit Debugger ................................... 285
MPLAB PM3 Device Programmer .................................... 285
MPLAB REAL ICE In-Circuit Emulator System ................ 285
MPLAB X Integrated Development
I
I/O Ports............................................................................155
Parallel I/O (PIO).......................................................155
Write/Read Timing ....................................................156
Environment Software .............................................. 283
MPLAB X SIM Software Simulator ................................... 285
MPLIB Object Librarian..................................................... 284
MPLINK Object Linker ...................................................... 284
2
I C
Control Registers ......................................................227
Operating Modes ......................................................225
In-Circuit Debugger...........................................................272
In-Circuit Emulation...........................................................267
In-Circuit Serial Programming (ICSP) ....................... 267, 272
Input Capture ....................................................................191
Control Register........................................................192
Input Change Notification..................................................156
O
Open-Drain Configuration................................................. 156
Oscillator Configuration .................................................... 135
Control Registers...................................................... 139
Output Compare ............................................................... 193
Modes....................................................................... 194
Operation Diagram ................................................... 194
DS70000318G-page 388
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Interrupt Controller for dsPIC33FJ06GS102 .............. 53
Interrupt Controller for dsPIC33FJ06GS202 .............. 54
P
Packaging ......................................................................... 351
Details....................................................................... 353
Marking ..................................................................... 351
Peripheral Module Disable (PMD) .................................... 148
Peripheral Pin Select (PPS).............................................. 157
PICkit 3 In-Circuit Debugger/Programmer ........................ 285
Pinout I/O Descriptions (table)............................................ 19
Power-on Reset (POR) ....................................................... 94
Power-Saving Features .................................................... 147
Clock Frequency and Switching................................ 147
Power-up Timer (PWRT) .................................................... 94
PPS
Control Registers ...................................................... 161
Selectable Input Sources.......................................... 158
Selection Output Sources ......................................... 159
Program Address Space..................................................... 43
Construction................................................................ 78
Data Access from Program Memory Using
Interrupt Controller for dsPIC33FJ16GS402/404 ....... 55
Interrupt Controller for dsPIC33FJ16GS502 .............. 56
Interrupt Controller for dsPIC33FJ16GS504 .............. 57
NVM............................................................................ 71
Output Compare for dsPIC33FJ06GS101/X02 .......... 59
Output Compare for dsPIC33FJ16GSX02
and dsPIC33FJ06GSX04 ................................... 59
PMD for dsPIC33FJ06GS101 .................................... 71
PMD for dsPIC33FJ06GS102 .................................... 71
PMD for dsPIC33FJ06GS202 .................................... 72
PMD for dsPIC33FJ16GS402/404 ............................. 72
PMD for dsPIC33FJ16GS502/504 ............................. 72
PORTA ....................................................................... 70
PORTB for dsPIC33FJ06GS101................................ 70
PORTB for dsPIC33FJ06GS102/202
and dsPIC33FJ16GS402/404/502/504............... 70
PORTC for dsPIC33FJ16GS404/504......................... 70
PPS Input ................................................................... 68
PPS Output for dsPIC33FJ06GS101 ......................... 68
PPS Output for dsPIC33FJ06GS102/202
and dsPIC33FJ16GS402/502............................. 69
PPS Output for dsPIC33FJ16GS404/504 .................. 69
SPI1............................................................................ 62
System Control........................................................... 71
Timers for dsPIC33FJ06GS101/X02.......................... 58
Timers for dsPIC33FJ16GSX02/X04.......................... 58
UART1........................................................................ 62
Program Space Visibility..................................... 81
Data Access from Program Memory Using
Table Instructions ............................................... 80
Data Access from, Address Generation...................... 79
Memory Maps ............................................................. 43
Table Read Instructions
TBLRDH ............................................................. 80
TBLRDL .............................................................. 80
Visibility Operation ...................................................... 81
Program Memory
Registers
Interrupt Vector ........................................................... 44
Organization................................................................ 44
Reset Vector ............................................................... 44
ACLKCON (Auxiliary Clock Divisor Control)............. 144
ADBASE (Analog-to-Digital Base)............................ 250
ADCON (Analog-to-Digital Control).......................... 247
ADCPC0 (Analog-to-Digital Convert Pair
Control 0).......................................................... 251
ADCPC1 (Analog-to-Digital Convert Pair
Control 1).......................................................... 254
ADCPC2 (Analog-to-Digital Convert Pair
Control 2).......................................................... 257
ADCPC3 (Analog-to-Digital Convert Pair
R
Reference Clock Generation............................................. 138
Register Maps
Analog Comparator Control for
dsPIC33FJ06GS202........................................... 67
Analog Comparator Control for
dsPIC33FJ16GS503/504.................................... 67
Change Notification for dsPIC33FJ06GS101 ............. 51
Change Notification for dsPIC33FJ06GS102/202
and dsPIC33FJ16GS402/502............................. 51
Change Notification for
dsPIC33FJ16GS404/504.................................... 51
CPU Core.................................................................... 50
High-Speed 10-Bit ADC for dsPIC33FJ06GS101....... 63
High-Speed 10-Bit ADC for dsPIC33FJ06GS102....... 63
High-Speed 10-Bit ADC for dsPIC33FJ06GS202....... 64
High-Speed 10-Bit ADC for
dsPIC33FJ16GS402/404.................................... 64
High-Speed 10-Bit ADC for dsPIC33FJ16GS502....... 65
High-Speed 10-Bit ADC for dsPIC33FJ16GS504....... 66
High-Speed PWM ....................................................... 59
High-Speed PWM Generator 1................................... 60
High-Speed PWM Generator 2 for dsPIC33FJ06GS101/
202 and dsPIC33FJ16GSX02/X04..................... 60
High-Speed PWM Generator 3 for
dsPIC33FJ16GSX02/X04 ................................... 61
High-Speed PWM Generator 4 for dsPIC33FJ06GS101
and dsPIC33FJ16GS50X ................................... 61
I2C1 ............................................................................ 62
Input Capture for dsPIC33FJ06GS202....................... 58
Input Capture for dsPIC33FJ16GSX02/X04 ............... 59
Interrupt Controller for dsPIC33FJ06GS101............... 52
Control 3).......................................................... 260
ADPCFG (Analog-to-Digital Port Configuration)....... 250
ADSTAT (Analog-to-Digital Status) .......................... 249
ALTDTRx (PWMx Alternate Dead-Time).................. 210
CLKDIV (Clock Divisor) ............................................ 141
CMPCONx (Comparator Control x).......................... 265
CMPDACx (Comparator DAC x Control).................. 266
CORCON (Core Control).................................... 36, 101
DTRx (PWMx Dead-Time)........................................ 210
FCLCONx (PWMx Fault Current-Limit Control)........ 214
I2CxCON (I2Cx Control)........................................... 228
I2CxMSK (I2Cx Slave Mode Address Mask)............ 232
I2CxSTAT (I2Cx Status)........................................... 230
ICxCON (Input Capture x Control)............................ 192
IEC0 (Interrupt Enable Control 0)............................. 112
IEC1 (Interrupt Enable Control 1)............................. 114
IEC3 (Interrupt Enable Control 3)............................. 115
IEC4 (Interrupt Enable Control 4)............................. 115
IEC5 (Interrupt Enable Control 5)............................. 116
IEC6 (Interrupt Enable Control 6)............................. 117
IEC7 (Interrupt Enable Control 7)............................. 118
IFS0 (Interrupt Flag Status 0)................................... 105
IFS1 (Interrupt Flag Status 1)................................... 107
IFS3 (Interrupt Flag Status 3)................................... 108
IFS4 (Interrupt Flag Status 4)................................... 108
2008-2014 Microchip Technology Inc.
DS70000318G-page 389
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
IFS5 (Interrupt Flag Status 5) ...................................109
IFS6 (Interrupt Flag Status 6) ...................................110
IFS7 (Interrupt Flag Status 7) ...................................111
INTCON1 (Interrupt Control 1)..................................102
INTTREG (Interrupt Control and Status)...................133
IOCONx (PWMx I/O Control)....................................212
IPC0 (Interrupt Priority Control 0) .............................119
IPC1 (Interrupt Priority Control 1) .............................120
IPC14 (Interrupt Priority Control 14) .........................125
IPC16 (Interrupt Priority Control 16) .........................125
IPC2 (Interrupt Priority Control 2) .............................121
IPC23 (Interrupt Priority Control 23) .........................126
IPC24 (Interrupt Priority Control 24) .........................127
IPC25 (Interrupt Priority Control 25) .........................128
IPC26 (Interrupt Priority Control 26) .........................129
IPC27 (Interrupt Priority Control 27) .........................130
IPC28 (Interrupt Priority Control 28) .........................131
IPC29 (Interrupt Priority Control 29) .........................132
IPC3 (Interrupt Priority Control 3) .............................122
IPC4 (Interrupt Priority Control 4) .............................123
IPC5 (Interrupt Priority Control 5) .............................124
IPC7 (Interrupt Priority Control 7) .............................124
LEBCONx (Leading-Edge Blanking Control) ............217
MDC (PWM Master Duty Cycle) ...............................204
NVMCON (Flash Memory Control) .............................85
NVMKEY (Nonvolatile Memory Key) ..........................86
OCxCON (Output Compare x Control.......................195
OSCCON (Oscillator Control) ...................................139
OSCTUN (FRC Oscillator Tuning) ............................143
PDCx (PWMx Generator Duty Cycle).......................207
PHASEx (PWMx Primary Phase-Shift).....................208
PLLFBD (PLL Feedback Divisor)..............................142
PMD1 (Peripheral Module Disable Control 1)...........149
PMD2 (Peripheral Module Disable Control 2)...........150
PMD3 (Peripheral Module Disable Control 3)...........151
PMD4 (Peripheral Module Disable Control 4)...........151
PMD6 (Peripheral Module Disable Control 6)...........152
PMD7 (Peripheral Module Disable Control 7)...........153
PTCON (PWM Time Base Control) ..........................201
PTCON2 (PWM Clock Divider Select) ......................203
PTPER (PWM Master Time Base)............................203
PWMCAPx (Primary PWMx Time
RPOR1 (Peripheral Pin Select Output 1).................. 175
RPOR10 (Peripheral Pin Select Output 10).............. 179
RPOR11 (Peripheral Pin Select Output 11).............. 180
RPOR12 (Peripheral Pin Select Output 12).............. 180
RPOR13 (Peripheral Pin Select Output 13).............. 181
RPOR14 (Peripheral Pin Select Output 14).............. 181
RPOR16 (Peripheral Pin Select Output 16).............. 182
RPOR17 (Peripheral Pin Select Output 17).............. 182
RPOR2 (Peripheral Pin Select Output 2).................. 175
RPOR3 (Peripheral Pin Select Output 3).................. 176
RPOR4 (Peripheral Pin Select Output 4).................. 176
RPOR5 (Peripheral Pin Select Output 5).................. 177
RPOR6 (Peripheral Pin Select Output 6).................. 177
RPOR7 (Peripheral Pin Select Output 7).................. 178
RPOR8 (Peripheral Pin Select Output 8).................. 178
RPOR9 (Peripheral Pin Select Output 9).................. 179
SDCx (PWMx Secondary Duty Cycle)...................... 207
SEVTCMP (PWM Special Event Compare) ............. 204
SPHASEx (PWMx Secondary Phase-Shift).............. 209
SPIxCON1 (SPIx Control 1)...................................... 221
SPIxCON2 (SPIx Control 2)...................................... 223
SPIxSTAT (SPIx Status and Control) ....................... 220
SR (CPU STATUS)............................................. 34, 101
STRIGx (PWMx Secondary Trigger
Compare Value) ............................................... 216
T1CON (Timer1 Control) .......................................... 184
TRGCONx (PWMx Trigger Control) ......................... 211
TRIGx (PWMx Primary Trigger
Compare Value) ............................................... 216
TxCON (Timerx Control, x = 2)................................. 188
TyCON (Timery Control, y = 3)................................. 189
UxMODE (UARTx Mode).......................................... 234
UxSTA (UARTx Status and Control)......................... 236
Reset .................................................................................. 89
Configuration Mismatch.............................................. 95
Illegal Condition .......................................................... 95
Illegal Opcode....................................................... 89, 95
Security................................................................. 89, 96
System........................................................................ 92
Trap Conflict ............................................................... 95
Uninitialized W Register.................................. 89, 95, 96
Resets................................................................................. 89
Resources Required for Digital Phase-Shift
Base Capture)...................................................218
PWMCONx (PWMx Control).....................................205
RCON (Reset Control)................................................90
REFOCON (Reference Oscillator Control)................145
RPINR0 (Peripheral Pin Select Input 0)....................161
RPINR1 (Peripheral Pin Select Input 1)....................162
RPINR11 (Peripheral Pin Select Input 11)................165
RPINR18 (Peripheral Pin Select Input 18)................166
RPINR20 (Peripheral Pin Select Input 20)................167
RPINR21 (Peripheral Pin Select Input 21)................168
RPINR29 (Peripheral Pin Select Input 29)................169
RPINR3 (Peripheral Pin Select Input 3)....................163
RPINR30 (Peripheral Pin Select Input 30)................170
RPINR31 (Peripheral Pin Select Input 31)................171
RPINR32 (Peripheral Pin Select Input 32)................172
RPINR33 (Peripheral Pin Select Input 33)................173
RPINR34 (Peripheral Pin Select Input 34)................174
RPINR7 (Peripheral Pin Select Input 7)....................164
RPOR0 (Peripheral Pin Select Output 0)..................174
ZVT Converter ............................................................ 30
Revision History................................................................ 373
S
Serial Peripheral Interface (SPI)....................................... 219
Software RESET Instruction (SWR) ................................... 95
Software Stack Pointer, Frame Pointer
CALL Stack Frame ..................................................... 73
Special Features of the CPU ............................................ 267
Symbols Used in Opcode Descriptions ............................ 276
T
Temperature and Voltage Specifications
AC..................................................................... 300, 338
Timer1............................................................................... 183
Timer2/3............................................................................ 185
16-Bit Operation ....................................................... 186
32-Bit Operation ....................................................... 186
DS70000318G-page 390
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
Timing Diagrams
Analog-to-Digital Conversion per Input..................... 329
Timing Specifications
10-Bit High-Speed ADC Module............................... 328
Auxiliary PLL Clock................................................... 302
Comparator Module.................................................. 330
DAC Module ............................................................. 330
DAC Output Buffer DC ............................................. 331
High-Speed PWMx Requirements............................ 311
I2Cx Bus Data Requirements (Master Mode)........... 325
I2Cx Bus Data Requirements (Slave Mode)............. 327
Output Compare x Requirements............................. 309
PLL Clock ......................................................... 302, 338
Reset, Watchdog Timer, Oscillator Start-up Timer,
Power-up Timer and Brown-out Reset
Requirements ................................................... 306
Simple OCx/PWMx Mode Requirements ................. 310
Timer1 External Clock Requirements....................... 307
Timer2 External Clock Requirements....................... 308
Timer3 External Clock Requirements....................... 308
Brown-out Situations................................................... 94
External Clock........................................................... 301
High-Speed PWMx ................................................... 311
High-Speed PWMx Fault .......................................... 311
I/O ............................................................................. 304
I2Cx Bus Data (Master Mode) .................................. 324
I2Cx Bus Data (Slave Mode) .................................... 326
I2Cx Bus Start/Stop Bits (Master Mode)................... 324
I2Cx Bus Start/Stop Bits Slave Mode) ...................... 326
Input Capture x (ICx)................................................. 309
OCx/PWMx ............................................................... 310
Output Compare x (OCx).......................................... 309
Reset, Watchdog Timer, Oscillator Start-up Timer
and Power-up Timer ......................................... 305
SPIx Master Mode (Full-Duplex, CKE = 0,
CKP = x, SMP = 1) ........................................... 315
SPIx Master Mode (Full-Duplex, CKE = 1,
CKP = x, CMP = 1) ........................................... 314
SPIx Master Mode (Half-Duplex,
U
Universal Asynchronous Receiver
Transmitter (UART) .................................................. 233
Using the RCON Status Bits............................................... 96
Transmit Only, CKE = 0)................................... 312
SPIx Master Mode (Half-Duplex,
Transmit Only, CKE = 1)................................... 312
SPIx Slave Mode (Full-Duplex, CKE = 0,
CKP = 0, SMP = 0) ........................................... 322
SPIx Slave Mode (Full-Duplex, CKE = 0,
CKP = 1, SMP = 0) ........................................... 320
SPIx Slave Mode (Full-Duplex, CKE = 1,
CKP = 0, SMP = 0) ........................................... 316
SPIx Slave Mode (Full-Duplex, CKE = 1,
V
Voltage Regulator (On-Chip) ............................................ 270
W
Watchdog Timer (WDT)............................................ 267, 271
Programming Considerations................................... 271
Watchdog Timer Time-out Reset (WDTO) ......................... 95
WWW Address ................................................................. 392
WWW, On-Line Support ..................................................... 14
CKP = 1, SMP = 0) ........................................... 318
System Reset.............................................................. 93
Timer1, 2, 3 External Clock....................................... 307
Timing Requirements
10-Bit, High-Speed ADC Requirements.................... 329
External Clock................................................... 301, 345
I/O ............................................................................. 304
Input Capture x ......................................................... 309
Simple OCx/PWMx Mode ......................................... 345
SPIx Master Mode (CKE = 0) ................................... 339
SPIx Master Mode (Full-Duplex, CKE = 0,
CKP = x, SMP = 1) ........................................... 315
SPIx Master Mode (Full-Duplex, CKE = 1,
CKP = x, SMP = 1) ........................................... 314
SPIx Master Mode (Half-Duplex,
Transmit Only) .................................................. 313
SPIx Module Master Mode (CKE = 1)....................... 339
SPIx Module Slave Mode (CKE = 0)......................... 340
SPIx Module Slave Mode (CKE = 1)......................... 340
SPIx Slave Mode (Full-Duplex, CKE = 0,
CKP = 0, SMP = 0) ........................................... 323
SPIx Slave Mode (Full-Duplex, CKE = 0,
CKP = 1, SMP = 0) ........................................... 321
SPIx Slave Mode (Full-Duplex, CKE = 1,
CKP = 0, SMP = 0) ........................................... 317
SPIx Slave Mode (Full-Duplex, CKE = 1,
CKP = 1, SMP = 0) ........................................... 319
2008-2014 Microchip Technology Inc.
DS70000318G-page 391
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 392
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
Customers
should
contact
their
distributor,
representative or Field Application Engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
Technical support is available through the web site
at: http://microchip.com/support
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com. Under “Support”, click on
“Customer Change Notification” and follow the
registration instructions.
2008-2014 Microchip Technology Inc.
DS70000318G-page 393
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 394
2008-2014 Microchip Technology Inc.
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
Examples:
dsPIC 33 FJ 06 GS1 02 T - 50 E / SP - XXX
a) dsPIC33FJ06GS102-E/SP:
SMPS dsPIC33, 6-Kbyte program
memory, 28-pin, Extended
Microchip Trademark
Architecture
temperature, SPDIP package.
Flash Memory Family
Program Memory Size (Kbyte)
Product Group
Pin Count
Tape and Reel Flag (if applicable)
Speed (if applicable)
Temperature Range
Package
Pattern
Architecture:
33
=
=
16-bit Digital Signal Controller
Flash program memory, 3.3V
Flash Memory Family: FJ
Product Group:
GS1
=
=
=
=
Switch Mode Power Supply (SMPS) family
Switch Mode Power Supply (SMPS) family
Switch Mode Power Supply (SMPS) family
Switch Mode Power Supply (SMPS) family
GS2
GS4
GS5
Pin Count:
01
02
04
=
=
=
18-pin
28-pin
44-pin
Speed
50
=
50 MIPS
Temperature Range:
I
E
H
=
=
=
-40C to+85C (Industrial)
-40C to+125C (Extended)
-40C to+150C (High)
Package:
PT
ML
MM
SO
SP
TL
=
=
=
=
=
=
Plastic Thin Quad Flatpack - 10x10x1 mm body (TQFP)
Plastic Quad Flat, No Lead Package - 8x8 mm body (QFN)
Plastic Quad Flat, No Lead Package - 6x6x0.9 mm body (QFN-S)
Plastic Small Outline - Wide - 7.50 mm body (SOIC)
Skinny Plastic Dual In-Line - 300 mil body (SPDIP)
Very Thin Leadless Array - 6x6 mm body (VTLA)
2008-2014 Microchip Technology Inc.
DS70000318G-page 395
dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04
NOTES:
DS70000318G-page 396
2008-2014 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PIC logo, rfPIC, SST, SST Logo, SuperFlash
and UNI/O are registered trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
32
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MTP, SEEVAL and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
Analog-for-the-Digital Age, Application Maestro, BodyCom,
chipKIT, chipKIT logo, CodeGuard, dsPICDEM,
dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O,
Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA
and Z-Scale are trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
GestIC and ULPP are registered trademarks of Microchip
Technology Germany II GmbH & Co. KG, a subsidiary of
Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2008-2014, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 978-1-63276-216-0
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
== ISO/TS 16949 ==
2008-2014 Microchip Technology Inc.
DS70000318G-page 397
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-3019-1500
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Web Address:
www.microchip.com
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Germany - Dusseldorf
Tel: 49-2129-3766400
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Austin, TX
Tel: 512-257-3370
Germany - Pforzheim
Tel: 49-7231-424750
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Boston
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
Italy - Venice
Tel: 39-049-7625286
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Poland - Warsaw
Tel: 48-22-3325737
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Sweden - Stockholm
Tel: 46-8-5090-4654
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Detroit
Novi, MI
Tel: 248-848-4000
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Houston, TX
Tel: 281-894-5983
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
Los Angeles
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Canada - Toronto
Tel: 905-673-0699
Fax: 905-673-6509
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
03/25/14
DS70000318G-page 398
2008-2014 Microchip Technology Inc.
相关型号:
DSPIC33FJ16MC101-E/P
16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDIP20, 0.300 INCH, LEAD FREE, PLASTIC, DIP-20
MICROCHIP
DSPIC33FJ16MC304-E/ML
16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQCC44, 8 X 8 MM, LEAD FREE, PLASTIC, QFN-44
MICROCHIP
©2020 ICPDF网 联系我们和版权申明