MCP6052T 概述
30 μA, High Precision Op Amps 30 μA ,高精度运算放大器
MCP6052T 数据手册
通过下载MCP6052T数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MCP6051/2/4
30 µA, High Precision Op Amps
Features
Description
• Low Offset Voltage: ±150 µV (maximum)
• Low Quiescent Current: 30 µA (typical)
• Rail-to-Rail Input and Output
The Microchip Technology Inc. MCP6051/2/4 family of
operational amplifiers (op amps) has low input offset
voltage (±150 µV, maximum) and rail-to-rail input and
output operation. This family is unity gain stable and
has a gain bandwidth product of 385 kHz (typical).
These devices operate with a single supply voltage as
low as 1.8V, while drawing low quiescent current per
amplifier (30 µA, typical). These features make the
family of op amps well suited for single-supply, high
precision, battery-powered applications.
• Wide Supply Voltage Range: 1.8V to 6.0V
• Gain Bandwidth Product: 385 kHz (typical)
• Unity Gain Stable
• Extended Temperature Range: -40°C to +125°C
• No Phase Reversal
The MCP6051/2/4 family is offered in single
(MCP6051), dual (MCP6052), and quad (MCP6054)
configurations.
Applications
• Automotive
• Portable Instrumentation
• Sensor Conditioning
• Battery Powered Systems
• Medical Instrumentation
• Test Equipment
The MCP6051/2/4 is designed with Microchip’s
advanced CMOS process. All devices are available in
the extended temperature range, with a power supply
range of 1.8V to 6.0V.
Package Types
• Analog Filters
MCP6051
SOIC
MCP6052
SOIC
Design Aids
NC
VDD
8
1
8
7
6
5
1
2
3
4
NC
VOUTA
• SPICE Macro Models
• FilterLab® Software
• Mindi™ Circuit Designer & Simulator
• Microchip Advanced Part Selector (MAPS)
• Analog Demonstration and Evaluation Boards
• Application Notes
VDD
VOUT
NC
VOUTB
2
3
4
7
6
5
VIN
–
+
VINA
–
+
VINB
VINB
–
+
VIN
VINA
VSS
VSS
MCP6051
2x3 TDFN *
MCP6052
2x3 TDFN *
NC
VOUTA
1
1
8
7
8
7
NC
VDD
Typical Application
VIN–
VINA
–
+
VDD
VOUT
VOUTB
2
2
EP
9
EP
9
VIN
+
VINA
VINB
VINB
–
+
3
4
6
5
3
4
6
5
RL
VSS
VSS
NC
VOUT
MCP6054
SOIC, TSSOP
ZIN
MCP6051
VOUTD
1
2
3
4
5
6
7
14
13
12
11
10
9
VOUTA
VIND
VIND
VSS
–
VINA
–
+
C
+
VINA
ZIN = RL + jωL
L = RLRC
R
VDD
VINB
VINB
Gyrator
VINC
+
–
+
–
VINC
VOUTC
8
VOUTB
* Includes Exposed Thermal Pad (EP); see Table 3-1.
© 2009 Microchip Technology Inc.
DS22182A-page 1
MCP6051/2/4
NOTES:
DS22182A-page 2
© 2009 Microchip Technology Inc.
MCP6051/2/4
1.0
1.1
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
VDD – VSS ........................................................................7.0V
Current at Input Pins.....................................................±2 mA
Analog Inputs (VIN+, VIN-)†† .......... VSS – 1.0V to VDD + 1.0V
All Other Inputs and Outputs ......... VSS – 0.3V to VDD + 0.3V
† Notice: Stresses above those listed under “Absolute
Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional
operation of the device at those or any other conditions
above those indicated in the operational listings of this
specification is not implied. Exposure to maximum
rating conditions for extended periods may affect
device reliability.
Difference Input Voltage ...................................... |VDD – VSS
|
Output Short-Circuit Current .................................continuous
Current at Output and Supply Pins ............................±30 mA
Storage Temperature ....................................-65°C to +150°C
Maximum Junction Temperature (TJ)..........................+150°C
ESD protection on all pins (HBM; MM) ................ ≥ 4 kV; 400V
†† See 4.1.2 “Input Voltage And Current Limits”
1.2
Specifications
TABLE 1-1:
DC ELECTRICAL SPECIFICATIONS
Electrical Characteristics: Unless otherwise indicated, VDD = +1.8V to +6.0V, VSS= GND, TA= +25°C, VCM = VDD/2,
VOUT ≈ VDD/2, VL = VDD/2 and RL = 100 kΩ to VL. (Refer to Figure 1-1).
Parameters
Input Offset
Sym
Min
Typ
Max
Units
Conditions
Input Offset Voltage
VOS
-150
—
—
+150
—
µV VDD = 3.0V,
VCM = VDD/3
Input Offset Drift with Temperature
ΔVOS/ΔTA
ΔVOS/ΔTA
PSRR
±1.5
±4.0
87
µV/°C TA= -40°C to +85°C,
VDD = 3.0V, VCM = VDD/3
—
—
µV/°C TA= +85°C to +125°C,
VDD = 3.0V, VCM = VDD/3
Power Supply Rejection Ratio
Input Bias Current and Impedance
Input Bias Current
70
—
dB
VCM = VSS
IB
IB
—
—
—
—
—
—
±1.0
60
100
—
pA
pA TA = +85°C
IB
1100
±1.0
1013||6
1013||6
5000
—
pA TA = +125°C
Input Offset Current
IOS
ZCM
ZDIFF
pA
Common Mode Input Impedance
Differential Input Impedance
Common Mode
—
Ω||pF
Ω||pF
—
Common Mode Input Voltage Range
VCMR
VCMR
VSS−0.2
VSS−0.3
74
—
—
90
VDD+0.2
VDD+0.3
—
V
VDD = 1.8V (Note 1)
VDD = 6.0V (Note 1)
CM = -0.2V to 2.0V,
VDD = 1.8V
dB VCM = -0.3V to 6.3V,
V
Common Mode Rejection Ratio
CMRR
dB
V
74
72
74
91
87
89
—
—
—
VDD = 6.0V
dB
dB
V
CM = 3.0V to 6.3V,
VDD = 6.0V
CM = -0.3V to 3.0V,
VDD = 6.0V
V
Note 1: Figure 2-13 shows how VCMR changed across temperature.
© 2009 Microchip Technology Inc.
DS22182A-page 3
MCP6051/2/4
TABLE 1-1:
DC ELECTRICAL SPECIFICATIONS (CONTINUED)
Electrical Characteristics: Unless otherwise indicated, VDD = +1.8V to +6.0V, VSS= GND, TA= +25°C, VCM = VDD/2,
VOUT ≈ VDD/2, VL = VDD/2 and RL = 100 kΩ to VL. (Refer to Figure 1-1).
Parameters
Open-Loop Gain
Sym
Min
Typ
Max
Units
Conditions
DC Open-Loop Gain
(Large Signal)
AOL
95
115
—
dB 0.2V < VOUT <(VDD-0.2V)
VCM = VSS
Output
Maximum Output Voltage Swing
VOL, VOH
VSS+15
—
VDD–15
mV G = +2 V/V,
0.5V input overdrive
Output Short-Circuit Current
ISC
—
—
±5
—
—
mA VDD = 1.8V
±26
mA
VDD = 6.0V
Power Supply
Supply Voltage
VDD
IQ
1.8
15
—
6.0
45
V
Quiescent Current per Amplifier
30
µA IO = 0, VDD = 6.0V
VCM = 0.9VDD
Note 1: Figure 2-13 shows how VCMR changed across temperature.
TABLE 1-2: AC ELECTRICAL SPECIFICATIONS
Electrical Characteristics: Unless otherwise indicated, TA = +25°C, VDD = +1.8 to +6.0V, VSS = GND, VCM = VDD/2,
VOUT ≈ VDD/2, VL = VDD/2, RL = 100 kΩ to VL and CL = 60 pF. (Refer to Figure 1-1).
Parameters
Sym
Min
Typ
Max
Units
Conditions
AC Response
Gain Bandwidth Product
Phase Margin
GBWP
PM
—
—
—
385
61
—
—
—
kHz
°
G = +1 V/V
Slew Rate
SR
0.15
V/µs
Noise
Input Noise Voltage
Input Noise Voltage Density
Input Noise Current Density
Eni
eni
ini
—
—
—
5.0
34
—
—
—
µVp-p f = 0.1 Hz to 10 Hz
nV/√Hz f = 10 kHz
0.6
fA/√Hz f = 1 kHz
TABLE 1-3:
TEMPERATURE SPECIFICATIONS
Electrical Characteristics: Unless otherwise indicated, VDD = +1.8V to +6.0V and VSS = GND.
Parameters
Temperature Ranges
Sym
Min
Typ
Max
Units
Conditions
Operating Temperature Range
Storage Temperature Range
TA
TA
-40
-65
—
—
+125
+150
°C
°C
Note 1
Thermal Package Resistances
Thermal Resistance, 8L-2x3 TDFN
Thermal Resistance, 8L-SOIC
Thermal Resistance, 14L-SOIC
Thermal Resistance, 14L-TSSOP
θJA
θJA
θJA
θJA
—
—
—
—
41
149.5
95.3
100
—
—
—
—
°C/W
°C/W
°C/W
°C/W
Note 1: The internal junction temperature (TJ) must not exceed the absolute maximum specification of +150°C.
DS22182A-page 4
© 2009 Microchip Technology Inc.
MCP6051/2/4
1.3
Test Circuits
CF
6.8 pF
The circuit used for most DC and AC tests is shown in
Figure 1-1. This circuit can independently set VCM and
VOUT; see Equation 1-1. Note that VCM is not the
circuit’s common mode voltage ((VP + VM)/2), and that
VOST includes VOS plus the effects (on the input offset
RG
100 kΩ
RF
100 kΩ
VDD/2
VP
error, VOST) of temperature, CMRR, PSRR and AOL
.
VDD
VIN+
EQUATION 1-1:
CB1
100 nF
CB2
1 µF
GDM = RF ⁄ RG
MCP605X
VCM = (VP + VDD ⁄ 2) ⁄ 2
VOST = VIN– – VIN+
VIN–
VOUT = (VDD ⁄ 2) + (VP – VM) + VOST(1 + GDM
)
VOUT
VM
RL
10 kΩ
CL
60 pF
RG
100 kΩ
RF
100 kΩ
Where:
GDM = Differential Mode Gain
(V/V)
(V)
VCM = Op Amp’s Common Mode
CF
6.8 pF
Input Voltage
VL
VOST = Op Amp’s Total Input Offset
(mV)
Voltage
FIGURE 1-1:
AC and DC Test Circuit for
Most Specifications.
© 2009 Microchip Technology Inc.
DS22182A-page 5
MCP6051/2/4
NOTES:
DS22182A-page 6
© 2009 Microchip Technology Inc.
MCP6051/2/4
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +6.0V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 100 kΩ to VL and CL = 60 pF.
14%
12%
10%
8%
750
600
450
300
150
0
1244 Samples
VDD = 3.0V
VCM = VDD/3
VDD = 6.0V
Representative Part
6%
-150
-300
-450
-600
-750
TA = -40°C
TA = +25°C
TA = +85°C
TA = +125°C
4%
2%
0%
Input Offset Voltage (µV)
Common Mode Input Voltage (V)
FIGURE 2-1:
Input Offset Voltage with
FIGURE 2-4:
Input Offset Voltage vs.
V
= 3.0V.
Common Mode Input Voltage with V = 6.0V.
DD
DD
750
27%
1244 Samples
600
450
300
150
0
VDD = 3.0V
Representative Part
24%
21%
18%
15%
12%
9%
VDD = 3.0V
VCM = VDD/3
TA = -40
°C to +85°C
-150
-300
-450
-600
-750
TA = -40°C
TA = +25°C
TA = +85°C
6%
3%
TA = +125°C
0%
Input Offset Drift with Temperature (µV/°C)
Common Mode Input Voltage (V)
FIGURE 2-2:
Input Offset Voltage Drift
FIGURE 2-5:
Input Offset Voltage vs.
with V = 3.0V and T ≤ +85°C.
Common Mode Input Voltage with V = 3.0V.
DD
A
DD
27%
24%
21%
18%
15%
12%
9%
1244 Samples
VDD = 3.0V
VCM = VDD/3
TA = +85°C to +125°C
6%
3%
0%
Input Offset Drift with Temperature (µV/°C)
FIGURE 2-3:
Input Offset Voltage Drift
FIGURE 2-6:
Input Offset Voltage vs.
with V = 3.0V and T ≥ +85°C.
Common Mode Input Voltage with V = 1.8V.
DD
A
DD
© 2009 Microchip Technology Inc.
DS22182A-page 7
MCP6051/2/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +6.0V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 100 kΩ to VL and CL = 60 pF.
350
50
45
40
35
Representative Part
250
150
30
25
20
15
10
5
50
-50
VDD = 6.0V
VDD = 3.0V
-150
-250
-350
f = 10 kHz
DD = 6.0V
V
VDD = 1.8V
0
Output Voltage (V)
Common Mode Input Voltage (V)
FIGURE 2-7:
Input Offset Voltage vs.
FIGURE 2-10:
Input Noise Voltage Density
Output Voltage.
vs. Common Mode Input Voltage.
750
110
TA = +125°C
PSRR-
Representative Part
600
450
300
150
0
Representative Part
100
90
80
70
60
50
40
30
20
TA = +85°C
TA = +25°C
TA = -40°C
CMRR
PSRR+
-150
-300
-450
-600
-750
10
100
1k
Frequency (Hz)
10k
100k
1M
Power Supply Voltage (V)
FIGURE 2-8:
Input Offset Voltage vs.
FIGURE 2-11:
CMRR, PSRR vs.
Power Supply Voltage.
Frequency.
110
105
1,000
CMRR (VDD = 6.0V, VCM = -0.3V to 6.3V)
100
95
90
85
80
75
70
65
60
100
PSRR (VDD = 1.8V to 6.0V, VCM = VSS
)
10
0.1
1
10
100
1k
10k 100k
-50
-25
0
25
50
75
100
125
Frequency (Hz)
Ambient Temperature (°C)
FIGURE 2-9:
Input Noise Voltage Density
FIGURE 2-12:
CMRR, PSRR vs. Ambient
vs. Frequency.
Temperature.
DS22182A-page 8
© 2009 Microchip Technology Inc.
MCP6051/2/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +6.0V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 100 kΩ to VL and CL = 60 pF.
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0.00
-0.05
-0.10
-0.15
-0.20
-0.25
-0.30
-0.35
45
40
35
30
25
20
15
10
VDD = 6.0V
VCM = 0.9VDD
VDD - VOH @ VDD = 6.0V
@ VDD = 3.0V
@ VDD = 1.8V
VOL - VSS @ VDD = 1.8V
VOL - VSS @ VDD = 3.0V
VOL - VSS @ VDD = 6.0V
VDD = 1.8V
CM = 0.9VDD
V
-50
-25
0
25
50
75
100 125
-50
-25
0
25
50
75
100 125
Ambient Temperature (°C)
Ambient Temperature (°C)
FIGURE 2-13:
Common Mode Input
FIGURE 2-16:
Quiescent Current vs
Voltage Range Limit vs. Ambient Temperature.
Ambient Temperature with V
= 0.9V
.
CM
DD
45
10000
VDD = 6.0V
VCM = 0.9VDD
VDD = 6.0V
40
V
CM = VDD
35
30
25
20
15
10
5
1000
100
10
Input Bias Current
TA = +125°C
TA = +85°C
TA = +25°C
TA = -40°C
Input Offset Current
0
1
25
45
65
85
105
125
Ambient Temperature (°C)
Power Supply Voltage (V)
FIGURE 2-14:
Input Bias, Offset Currents
FIGURE 2-17:
Quiescent Current vs.
vs. Ambient Temperature.
Power Supply Voltage with V
= 0.9V
.
CM
DD
120
0
10000
VDD = 6.0V
Open-Loop Gain
100
-30
1000
100
10
80
-60
TA = +125°C
TA = +85°C
Open-Loop Phase
60
40
20
0
-90
-120
-150
-180
-210
VDD = 6.0V
1
-20
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Common Mode Input Votlage (V)
0.1
1
10100 1k10k100k1M10M
Frequency (Hz)
FIGURE 2-15:
Input Bias Current vs.
FIGURE 2-18:
Open-Loop Gain, Phase vs.
Common Mode Input Voltage.
Frequency.
© 2009 Microchip Technology Inc.
DS22182A-page 9
MCP6051/2/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +6.0V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 100 kΩ to VL and CL = 60 pF.
150
145
140
135
130
125
120
115
110
105
100
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
180
160
140
120
100
80
Gain Bandwidth Product
60
40
VDD = 6.0V
G = +1 V/V
Phase Margin
RL = 100 kΩ
VSS + 0.2V < VOUT < VDD - 0.2V
20
0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
Power Supply Voltage (V)
Common Mode Input Voltage (V)
FIGURE 2-19:
DC Open-Loop Gain vs.
FIGURE 2-22:
Gain Bandwidth Product,
Power Supply Voltage.
Phase Margin vs. Common Mode Input Voltage.
150
145
140
135
130
125
120
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
180
160
140
120
100
80
VDD = 6.0V
Gain Bandwidth Product
VDD = 1.8V
115
60
110
105
100
Large Signal AOL
0.20 0.25
40
Phase Margin
VDD = 6.0V
G = +1 V/V
20
0
0.00
0.05
0.10
0.15
-50 -25
0
25
50
75 100 125
Output Voltage Headroom
VDD - VOH or VOL - VSS (V)
Ambient Temperature (°C)
FIGURE 2-20:
DC Open-Loop Gain vs.
FIGURE 2-23:
Gain Bandwidth Product,
Output Voltage Headroom.
Phase Margin vs. Ambient Temperature.
140
130
120
110
100
0.9
0.8
0.7
180
160
140
120
100
80
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Gain Bandwidth Product
60
40
VDD = 1.8V
G = +1 V/V
Phase Margin
90
80
Input Referred
20
0
100
1k
10k
100k
1M
-50 -25
0
25
50
75 100 125
Frequency (Hz)
Ambient Temperature (°C)
FIGURE 2-21:
Channel-to-Channel
FIGURE 2-24:
Gain Bandwidth Product,
Separation vs. Frequency ( MCP6052/4 only).
Phase Margin vs. Ambient Temperature.
DS22182A-page 10
© 2009 Microchip Technology Inc.
MCP6051/2/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +6.0V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 100 kΩ to VL and CL = 60 pF.
40
35
30
25
20
15
10
5
16.0
14.0
12.0
10.0
8.0
TA = -40°C
TA = +25°C
VDD - VOH
T
A = +85°C
TA = +125°C
6.0
VSS - VOL
4.0
2.0
0
0.0
-50
-25
0
25
50
75
100 125
Power Supply Voltage (V)
Ambient Temperature (°C)
FIGURE 2-25:
Ouput Short Circuit Current
FIGURE 2-28:
Output Voltage Headroom
vs. Power Supply Voltage.
vs. Ambient Temperature.
10
0.30
VDD = 6.0V
Falling Edge, VDD = 6.0V
Falling Edge, VDD = 1.8V
0.25
0.20
0.15
0.10
0.05
0.00
VDD = 1.8V
1
Rising Edge, VDD = 6.0V
Rising Edge, VDD = 1.8V
0.1
100
1k
10k
100k
1M
-50
-25
0
25
50
75
100 125
Frequency (Hz)
Ambient Temperature (°C)
FIGURE 2-26:
Output Voltage Swing vs.
FIGURE 2-29:
Slew Rate vs. Ambient
Frequency.
Temperature.
70
65
60
55
50
45
40
35
30
25
20
15
10
(VDD - VOH)/IOUT
VDD = 1.8V
(VOL - VSS)/(-IOUT
)
(VDD - VOH)/IOUT
VDD = 6.0V
G = +1 V/V
(VOL - VSS)/(-IOUT
)
VDD = 6.0V
0.1
1
10
Time (2 µs/div)
Output Current (mA)
FIGURE 2-27:
Ratio of Output Voltage
FIGURE 2-30:
Small Signal Non-Inverting
Headroom to Output Current vs. Output Current.
Pulse Response.
© 2009 Microchip Technology Inc.
DS22182A-page 11
MCP6051/2/4
Note: Unless otherwise indicated, TA = +25°C, VDD = +1.8V to +6.0V, VSS = GND, VCM = VDD/2, VOUT ≈ VDD/2,
VL = VDD/2, RL = 100 kΩ to VL and CL = 60 pF.
7.0
6.0
VDD = 6.0V
G = -1 V/V
VOUT
5.0
VIN
4.0
3.0
2.0
1.0
VDD = 6.0V
G = +2 V/V
0.0
-1.0
Time (2 µs/div)
Time (0.1 ms/div)
FIGURE 2-31:
Small Signal Inverting Pulse
FIGURE 2-34:
The MCP6051/2/4 Shows
Response.
No Phase Reversal.
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
10000
1000
100
10
GN:
101 V/V
11 V/V
1 V/V
VDD = 6.0V
G = +1 V/V
1
10
100
1k
10k
100k
1M
Frequency (Hz)
Time (0.02 ms/div)
FIGURE 2-32:
Large Signal Non-Inverting
FIGURE 2-35:
Closed Loop Output
Pulse Response.
Impedance vs. Frequency.
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
-0.5
1m
100
µ
VDD = 6.0V
G = -1 V/V
10µ
1µ
100n
10n
TA = -40°C
TA = +25°C
TA = +85°C
TA = +125°C
1n
100p
10p
1p
-1.0 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0
IN (V)
V
Time (0.02 ms/div)
FIGURE 2-33:
Large Signal Inverting Pulse
FIGURE 2-36:
Measured Input Current vs.
Response.
Input Voltage (below V ).
SS
DS22182A-page 12
© 2009 Microchip Technology Inc.
MCP6051/2/4
3.0
PIN DESCRIPTIONS
Descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
MCP6051
PIN FUNCTION TABLE
MCP6052
MCP6054
Symbol
Description
SOIC,
TSSOP
SOIC
2x3 TDFN
SOIC
2x3 TDFN
6
2
6
2
1
2
3
8
5
6
1
2
3
8
5
6
1
2
3
4
5
6
VOUT, VOUTA
Analog Output (op amp A)
Inverting Input (op amp A)
Non-inverting Input (op amp A)
Positive Power Supply
VIN–, VINA
VIN+, VINA
VDD
–
3
3
+
7
7
—
—
—
—
VINB
+
–
Non-inverting Input (op amp B)
Inverting Input (op amp B)
VINB
—
—
—
—
7
7
7
VOUTB
VOUTC
Analog Output (op amp B)
Analog Output (op amp C)
Inverting Input (op amp C)
Non-inverting Input (op amp C)
Negative Power Supply
—
—
—
4
—
—
—
4
8
—
—
9
VINC
VINC
–
—
—
10
11
12
13
14
—
—
+
4
4
VSS
—
—
—
—
—
—
—
—
—
—
—
9
VIND+
Non-inverting Input (op amp D)
Inverting Input (op amp D)
Analog Output (op amp D)
No Internal Connection
—
—
VIND–
—
—
VOUTD
NC
1, 5, 8
—
1, 5, 8
9
Exposed Thermal Pad (EP); must be
EP
connected to VSS
.
3.1
Analog Outputs
3.3
Power Supply Pins
The output pins are low-impedance voltage sources.
The positive power supply (VDD) is 1.8V to 6.0V higher
than the negative power supply (VSS). For normal
operation, the other pins are at voltages between VSS
3.2
Analog Inputs
and VDD
.
The non-inverting and inverting inputs are high-
impedance CMOS inputs with low bias currents.
Typically, these parts are used in a single (positive)
supply configuration. In this case, VSS is connected to
ground and VDD is connected to the supply. VDD will
need bypass capacitors.
3.4
Exposed Thermal Pad (EP)
There is an internal electrical connection between the
Exposed Thermal Pad (EP) and the VSS pin; they must
be connected to the same potential on the Printed
Circuit Board (PCB).
© 2009 Microchip Technology Inc.
DS22182A-page 13
MCP6051/2/4
NOTES:
DS22182A-page 14
© 2009 Microchip Technology Inc.
MCP6051/2/4
4.0
APPLICATION INFORMATION
VDD
The MCP6051/2/4 family of op amps is manufactured
using Microchip’s state-of-the-art CMOS process and
is specifically designed for low-power, high precision
applications.
D1 D2
V1
V2
R1
R2
MCP605X
4.1
Rail-to-Rail Input
4.1.1
PHASE REVERSAL
The MCP6051/2/4 op amps are designed to prevent
phase reversal when the input pins exceed the supply
voltages. Figure 2-34 shows the input voltage
exceeding the supply voltage without any phase
reversal.
R3
VSS – (minimum expected V1)
R1 >
R2 >
2 mA
VSS – (minimum expected V2)
2 mA
4.1.2
INPUT VOLTAGE AND CURRENT
LIMITS
FIGURE 4-2:
Protecting the Analog
The ESD protection on the inputs can be depicted as
shown in Figure 4-1. This structure was chosen to
protect the input transistors and to minimize input bias
current (IB). The input ESD diodes clamp the inputs
when they try to go more than one diode drop below
VSS. They also clamp any voltage that go too far above
VDD; their breakdown voltage is high enough to allow
normal operation and low enough to bypass ESD
events within the specified limits.
Inputs.
It is also possible to connect the diodes to the left of the
resistors R1 and R2. In this case, the currents through
the diodes D1 and D2 need to be limited by some other
mechanism. The resistors then serve as in-rush current
limiters; the DC currents into the input pins (VIN+ and
VIN-) should be very small. A significant amount of
current can flow out of the inputs when the common
mode voltage (VCM) is below ground (VSS). (See
Figure 2-36).
Bond
VDD
4.1.3
NORMAL OPERATION
Pad
The input stage of the MCP6051/2/4 op amps uses two
differential input stages in parallel. One operates at a
low common mode input voltage (VCM), while the other
operates at a high VCM. With this topology, the device
operates with a VCM up to 300 mV above VDD and
300 mV below VSS. (See Figure 2-13) .The input offset
voltage is measured at VCM = VSS – 0.3V and
VDD + 0.3V to ensure proper operation.
Bond
Pad
Bond
Pad
Input
Stage
VIN+
VIN–
Bond
Pad
VSS
The transition between the input stages occurs when
VCM is near VDD – 1.1V (See Figures 2-4, 2-5 and
Figure 2-6). For the best distortion performance and
gain linearity, with non-inverting gains, avoid this region
of operation.
FIGURE 4-1:
Structures.
Simplified Analog Input ESD
In order to prevent damage and/or improper operation
of these op amps, the circuit they are in must limit the
voltages and currents at the VIN+ and VIN- pins (see
Absolute Maximum Ratings at the beginning of
Section 1.0 “Electrical Characteristics”). Figure 4-2
shows the recommended approach to protecting these
inputs. The internal ESD diodes prevent the input pins
(VIN+ and VIN-) from going too far below ground, and
the resistors R1 and R2 limit the possible current drawn
out of the input pins. Diodes D1 and D2 prevent the
input pins (VIN+ and VIN-) from going too far above
VDD. When implemented as shown, resistors R1 and
R2 also limit the current through D1 and D2.
4.2
Rail-to-Rail Output
The output voltage range of the MCP6051/2/4 op amps
is VSS + 15 mV (minimum) and VDD – 15 mV
(maximum) when RL = 10 kΩ is connected to VDD/2
and VDD = 6.0V. Refer to Figures 2-27 and 2-28 for
more information.
© 2009 Microchip Technology Inc.
DS22182A-page 15
MCP6051/2/4
After selecting RISO for your circuit, double-check the
resulting frequency response peaking and step
response overshoot. Modify RISO’s value until the
response is reasonable. Bench evaluation and
simulations with the MCP6051/2/4 SPICE macro
model are very helpful.
4.3
Capacitive Loads
Driving large capacitive loads can cause stability
problems for voltage feedback op amps. As the load
capacitance increases, the feedback loop’s phase
margin decreases and the closed-loop bandwidth is
reduced. This produces gain peaking in the frequency
response, with overshoot and ringing in the step
response. While a unity-gain buffer (G = +1) is the most
sensitive to capacitive loads, all gains show the same
general behavior.
4.4
Supply Bypass
With this family of operational amplifiers, the power
supply pin (VDD for single-supply) should have a local
bypass capacitor (i.e., 0.01 µF to 0.1 µF) within 2 mm
for good high frequency performance. It can use a bulk
capacitor (i.e., 1 µF or larger) within 100 mm to provide
large, slow currents. This bulk capacitor can be shared
with other analog parts.
When driving large capacitive loads with these op
amps (e.g., > 100 pF when G = +1), a small series
resistor at the output (RISO in Figure 4-3) improves the
feedback loop’s phase margin (stability) by making the
output load resistive at higher frequencies. The
bandwidth will be generally lower than the bandwidth
with no capacitance load.
4.5
Unused Op Amps
An unused op amp in a quad package (MCP6054)
should be configured as shown in Figure 4-5. These
circuits prevent the output from toggling and causing
crosstalk. Circuits A sets the op amp at its minimum
noise gain. The resistor divider produces any desired
reference voltage within the output voltage range of the
op amp; the op amp buffers that reference voltage.
Circuit B uses the minimum number of components
and operates as a comparator, but it may draw more
current.
–
RISO
VOUT
MCP605X
VIN
+
CL
FIGURE 4-3:
Output Resistor, R
ISO
Stabilizes Large Capacitive Loads.
Figure 4-4 gives recommended RISO values for
different capacitive loads and gains. The x-axis is the
normalized load capacitance (CL/GN), where GN is the
circuit's noise gain. For non-inverting gains, GN and the
Signal Gain are equal. For inverting gains, GN is
1+|Signal Gain| (e.g., -1 V/V gives GN = +2 V/V).
¼ MCP6054 (A)
VDD
¼ MCP6054 (B)
VDD
VDD
R1
R2
VREF
10000
VDD = 6.0 V
RL = 100 kΩ
R
1000
2
--------------------
×
V
= V
REF
DD
R
+ R
1
2
GN:
1 V/V
100
2 V/V
FIGURE 4-5:
Unused Op Amps.
≥
5 V/V
10
1
10p
100p
1n
10n
0.1µ
1µ
Normalized Load Capacitance; CL/GN (F)
FIGURE 4-4:
Recommended R
Values
ISO
for Capacitive Loads.
DS22182A-page 16
© 2009 Microchip Technology Inc.
MCP6051/2/4
4.6
PCB Surface Leakage
4.7
Application Circuits
In applications where low input bias current is critical,
Printed Circuit Board (PCB) surface leakage effects
need to be considered. Surface leakage is caused by
humidity, dust or other contamination on the board.
Under low humidity conditions, a typical resistance
between nearby traces is 1012Ω. A 5V difference would
cause 5 pA of current to flow; which is greater than the
MCP6051/2/4 family’s bias current at +25°C (±1.0 pA,
typical).
4.7.1
GYRATOR
The MCP6051/2/4 op amps can be used in gyrator
applicaitons. The gyrator is an electric circuit which can
make a capacitive circuit behave inductively. Figure 4-
7
shows an example of a gyrator simulating
inductance, with an approximately equivalent circuit
below. The two ZIN have similar values in typical
applications. The primary application for a gyrator is to
reduce the size and cost of a system by removing the
need for bulky, heavy and expensive inductors. For
example, RLC bandpass filter characteristics can be
realized with capacitors, resistors and operational
amplifiers without using inductors. Moreover, gyrators
will typically have higher accuracy than real inductors,
due to the lower cost of precision capacitors than
inductors.
The easiest way to reduce surface leakage is to use a
guard ring around sensitive pins (or traces). The guard
ring is biased at the same voltage as the sensitive pin.
An example of this type of layout is shown in
Figure 4-6.
Guard Ring
VIN– VIN+
VSS
.
RL
VOUT
ZIN
MCP6051
C
Gyrator
FIGURE 4-6:
for Inverting Gain.
Example Guard Ring Layout
R
ZIN = RL + jωL
1. Non-inverting Gain and Unity-Gain Buffer:
L = RLRC
a) Connect the non-inverting pin (VIN+) to the
input with a wire that does not touch the
PCB surface.
RL
ZIN
b) Connect the guard ring to the inverting input
pin (VIN–). This biases the guard ring to the
common mode input voltage.
Equivalent Circuit
L
2. Inverting Gain and Transimpedance Gain
Amplifiers (convert current to voltage, such as
photo detectors):
FIGURE 4-7:
Gyrator.
a) Connect the guard ring to the non-inverting
input pin (VIN+). This biases the guard ring
to the same reference voltage as the op
amp (e.g., VDD/2 or ground).
b) Connect the inverting pin (VIN–) to the input
with a wire that does not touch the PCB
surface.
© 2009 Microchip Technology Inc.
DS22182A-page 17
MCP6051/2/4
4.7.2
INSTRUMENTATION AMPLIFIER
4.7.3
PRECISION COMPARATOR
The MCP6051/2/4 op amps are well suited for condi-
tioning sensor signals in battery-powered applications.
Figure 4-8 shows a two op amp instrumentation
amplifier, using the MCP6052, that works well for
applications requiring rejection of common mode noise
at higher gains. The reference voltage (VREF) is
supplied by a low impedance source. In single supply
applications, VREF is typically VDD/2.
Use high gain before a comparator to improve the
latter’s input offset performance. Figure 4-9 shows a
gain of 11 V/V placed before a comparator. The
reference voltage VREF can be any value between the
supply rails.
VIN
MCP6051
RG
R1
R2
R2
R1
VREF
VOUT
1 MΩ
VOUT
MCP6541
100 kΩ
VREF
V2
V1
½
½
MCP6052
MCP6052
FIGURE 4-9:
Comparator.
Precision, Non-inverting
R1 2R1
⎛
⎞
VOUT = (V1 – V2) 1 + ----- + --------- + VREF
⎝
⎠
R2 RG
FIGURE 4-8:
Two Op Amp
Instrumentation Amplifier.
To obtain the best CMRR possible, and not limit the
performance by the resistor tolerances, set a high gain
with the RG resistor.
DS22182A-page 18
© 2009 Microchip Technology Inc.
MCP6051/2/4
5.5
Analog Demonstration and
Evaluation Boards
5.0
DESIGN AIDS
Microchip provides the basic design tools needed for
the MCP6051/2/4 family of op amps.
Microchip offers
a
broad spectrum of Analog
Demonstration and Evaluation Boards that are
designed to help you achieve faster time to market. For
5.1
SPICE Macro Model
a
complete listing of these boards and their
The latest SPICE macro model for the MCP6051/2/4
op amps is available on the Microchip web site at
www.microchip.com. This model is intended to be an
initial design tool that works well in the op amp’s linear
region of operation over the temperature range. See
the model file for information on its capabilities.
corresponding user’s guides and technical information,
visit the Microchip web site at www.microchip.com/
analogtools.
Some boards that are especially useful are:
• MCP6XXX Amplifier Evaluation Board 1
• MCP6XXX Amplifier Evaluation Board 2
• MCP6XXX Amplifier Evaluation Board 3
• MCP6XXX Amplifier Evaluation Board 4
• Active Filter Demo Board Kit
Bench testing is a very important part of any design and
cannot be replaced with simulations. Also, simulation
results using this macro model need to be validated by
comparing them to the data sheet specifications and
characteristic curves.
• 5/6-Pin SOT-23 Evaluation Board, P/N VSUPEV2
• 8-Pin SOIC/MSOP/TSSOP/DIP Evaluation Board,
P/N SOIC8EV
5.2
FilterLab® Software
Microchip’s FilterLab® software is an innovative
software tool that simplifies analog active filter (using
op amps) design. Available at no cost from the
Microchip web site at www.microchip.com/filterlab, the
FilterLab design tool provides full schematic diagrams
of the filter circuit with component values. It also
outputs the filter circuit in SPICE format, which can be
used with the macro model to simulate actual filter
performance.
• 14-Pin SOIC/TSSOP/DIP Evaluation Board,
P/N SOIC14EV
5.6
Application Notes
The following Microchip Analog Design Note and
Application Notes are available on the Microchip web
site at www.microchip.com/appnotes and are
recommended as supplemental reference resources:
• ADN003: “Select the Right Operational Amplifier
for your Filtering Circuits”, DS21821
5.3
Mindi™ Circuit Designer &
Simulator
• AN722: “Operational Amplifier Topologies and DC
Specifications”, DS00722
Microchip’s Mindi™ Circuit Designer & Simulator aids
in the design of various circuits useful for active filter,
amplifier and power-management applications. It is a
free online circuit designer & simulator available from
the Microchip web site at www.microchip.com/mindi.
This interactive circuit designer & simulator enables
designers to quickly generate circuit diagrams,
simulate circuits. Circuits developed using the Mindi
Circuit Designer & Simulator can be downloaded to a
personal computer or workstation.
• AN723: “Operational Amplifier AC Specifications
and Applications”, DS00723
• AN884: “Driving Capacitive Loads With Op
Amps”, DS00884
• AN990: “Analog Sensor Conditioning Circuits –
An Overview”, DS00990
• AN1177: “Op Amp Precision Design: DC Errors”,
DS01177
• AN1228: “Op Amp Precision Design: Random
Noise”, DS01228
5.4
Microchip Advanced Part Selector
(MAPS)
These application notes and others are listed in the
design guide:
MAPS is a software tool that helps semiconductor
professionals efficiently identify Microchip devices that
fit a particular design requirement. Available at no cost
from the Microchip website at www.microchip.com/
maps, the MAPS is an overall selection tool for
Microchip’s product portfolio that includes Analog,
Memory, MCUs and DSCs. Using this tool you can
define a filter to sort features for a parametric search of
devices and export side-by-side technical comparasion
reports. Helpful links are also provided for Datasheets,
Purchase, and Sampling of Microchip parts.
• “Signal Chain Design Guide”, DS21825
© 2009 Microchip Technology Inc.
DS22182A-page 19
MCP6051/2/4
NOTES:
DS22182A-page 20
© 2009 Microchip Technology Inc.
MCP6051/2/4
6.0
6.1
PACKAGING INFORMATION
Package Marking Information
8-Lead SOIC (150 mil) (MCP6051, MCP6052)
Example:
XXXXXXXX
MCP6051E
e
3
XXXXYYWW
SN^0919
NNN
256
8-Lead 2x3 TDFN (MCP6051, MCP6052)
Example:
XXX
YWW
NN
AHA
919
25
14-Lead SOIC (150 mil) (MCP6054)
Example:
XXXXXXXXXXX
XXXXXXXXXXX
MCP6054
E/SL^^
0919256
e
3
YYWWNNN
Example:
14-Lead TSSOP (MCP6054)
XXXXXXXX
YYWW
MCP6054E
0919
256
NNN
Legend: XX...X Customer-specific information
Y
Year code (last digit of calendar year)
YY
WW
NNN
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
e
3
Pb-free JEDEC designator for Matte Tin (Sn)
*
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
)
e3
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
© 2009 Microchip Technology Inc.
DS22182A-page 21
MCP6051/2/4
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢈꢆꢏꢐꢊꢈꢋꢑꢃꢆꢒꢍꢓꢔꢆMꢆꢓꢄꢕꢕꢖꢗꢘꢆꢙꢚꢛꢜꢆꢎꢎꢆ ꢖꢅ!ꢆ"ꢍꢏ#$%
ꢓꢖꢊꢃ& 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢔꢇꢍ3ꢇꢒꢉꢅ"ꢊꢇ)ꢃꢄꢒ 'ꢅꢔꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢕꢃꢍꢊꢌꢍꢎꢃꢔꢅꢂꢇꢍ3ꢇꢒꢃꢄꢒꢅꢑꢔꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢔ144)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢔꢁꢍꢌ&4ꢔꢇꢍ3ꢇꢒꢃꢄꢒ
D
e
N
E
E1
NOTE 1
1
2
3
α
h
b
h
c
φ
A2
A
L
A1
L1
β
5ꢄꢃ%
ꢕꢛ66ꢛꢕ-ꢙ-ꢚꢑ
ꢓꢃ&ꢉꢄ ꢃꢌꢄꢅ6ꢃ&ꢃ%
ꢕꢛ7
78ꢕ
ꢕꢘ9
7!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
7
ꢉ
:
ꢀꢁꢏꢜꢅ0ꢑ+
8ꢆꢉꢊꢇꢈꢈꢅ;ꢉꢃꢒꢎ%
ꢘ
M
ꢀꢁꢏ.
ꢖꢁꢀꢖ
M
M
M
ꢀꢁꢜ.
M
ꢖꢁꢏ.
ꢕꢌꢈ"ꢉ"ꢅꢂꢇꢍ3ꢇꢒꢉꢅꢙꢎꢃꢍ3ꢄꢉ
ꢑ%ꢇꢄ"ꢌ$$ꢅꢅ
ꢘꢏ
ꢘꢀ
-
ꢐ
8ꢆꢉꢊꢇꢈꢈꢅ=ꢃ"%ꢎ
>ꢁꢖꢖꢅ0ꢑ+
ꢕꢌꢈ"ꢉ"ꢅꢂꢇꢍ3ꢇꢒꢉꢅ=ꢃ"%ꢎ
8ꢆꢉꢊꢇꢈꢈꢅ6ꢉꢄꢒ%ꢎ
+ꢎꢇ&$ꢉꢊꢅ?ꢌꢔ%ꢃꢌꢄꢇꢈ@
2ꢌꢌ%ꢅ6ꢉꢄꢒ%ꢎ
-ꢀ
ꢓ
ꢎ
,ꢁꢝꢖꢅ0ꢑ+
ꢗꢁꢝꢖꢅ0ꢑ+
ꢖꢁꢏ.
ꢖꢁꢗꢖ
M
M
ꢖꢁ.ꢖ
ꢀꢁꢏꢜ
6
2ꢌꢌ%ꢔꢊꢃꢄ%
2ꢌꢌ%ꢅꢘꢄꢒꢈꢉ
6ꢉꢇ"ꢅꢙꢎꢃꢍ3ꢄꢉ
6ꢉꢇ"ꢅ=ꢃ"%ꢎ
ꢕꢌꢈ"ꢅꢓꢊꢇ$%ꢅꢘꢄꢒꢈꢉꢅꢙꢌꢔ
ꢕꢌꢈ"ꢅꢓꢊꢇ$%ꢅꢘꢄꢒꢈꢉꢅ0ꢌ%%ꢌ&
6ꢀ
ꢀ
ꢀꢁꢖꢗꢅꢚ-2
ꢖꢞ
ꢖꢁꢀꢜ
ꢖꢁ,ꢀ
.ꢞ
M
M
M
M
M
:ꢞ
ꢍ
(
ꢁ
ꢖꢁꢏ.
ꢖꢁ.ꢀ
ꢀ.ꢞ
ꢂ
.ꢞ
ꢀ.ꢞ
ꢓꢖꢊꢃꢉ&
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢐꢅꢑꢃꢒꢄꢃ$ꢃꢍꢇꢄ%ꢅ+ꢎꢇꢊꢇꢍ%ꢉꢊꢃ %ꢃꢍꢁ
,ꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄ ꢅꢓꢅꢇꢄ"ꢅ-ꢀꢅ"ꢌꢅꢄꢌ%ꢅꢃꢄꢍꢈ!"ꢉꢅ&ꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢔꢊꢌ%ꢊ! ꢃꢌꢄ ꢁꢅꢕꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢔꢊꢌ%ꢊ! ꢃꢌꢄ ꢅ ꢎꢇꢈꢈꢅꢄꢌ%ꢅꢉ#ꢍꢉꢉ"ꢅꢖꢁꢀ.ꢅ&&ꢅꢔꢉꢊꢅ ꢃ"ꢉꢁ
ꢗꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢒꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢒꢅꢔꢉꢊꢅꢘꢑꢕ-ꢅ/ꢀꢗꢁ.ꢕꢁ
0ꢑ+1 0ꢇ ꢃꢍꢅꢓꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢙꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢚ-21 ꢚꢉ$ꢉꢊꢉꢄꢍꢉꢅꢓꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢔ!ꢊꢔꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢕꢃꢍꢊꢌꢍꢎꢃꢔ ꢙꢉꢍꢎꢄꢌꢈꢌꢒꢋ ꢓꢊꢇ)ꢃꢄꢒ +ꢖꢗꢟꢖ.ꢜ0
DS22182A-page 22
© 2009 Microchip Technology Inc.
MCP6051/2/4
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢈꢆꢏꢐꢊꢈꢋꢑꢃꢆꢒꢍꢓꢔꢆMꢆꢓꢄꢕꢕꢖꢗꢘꢆꢙꢚꢛꢜꢆꢎꢎꢆ ꢖꢅ!ꢆ"ꢍꢏ#$%
ꢓꢖꢊꢃ& 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢔꢇꢍ3ꢇꢒꢉꢅ"ꢊꢇ)ꢃꢄꢒ 'ꢅꢔꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢕꢃꢍꢊꢌꢍꢎꢃꢔꢅꢂꢇꢍ3ꢇꢒꢃꢄꢒꢅꢑꢔꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢔ144)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢔꢁꢍꢌ&4ꢔꢇꢍ3ꢇꢒꢃꢄꢒ
© 2009 Microchip Technology Inc.
DS22182A-page 23
MCP6051/2/4
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆ'ꢐꢄꢈꢆ(ꢈꢄꢊꢘꢆꢓꢖꢆꢂꢃꢄꢅꢆꢇꢄꢌ)ꢄ*ꢃꢆꢒ+ꢓꢔꢆMꢆ,-ꢙ-ꢜꢚ./ꢆꢎꢎꢆ ꢖꢅ!ꢆ"0'(ꢓ%
ꢓꢖꢊꢃ& 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢔꢇꢍ3ꢇꢒꢉꢅ"ꢊꢇ)ꢃꢄꢒ 'ꢅꢔꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢕꢃꢍꢊꢌꢍꢎꢃꢔꢅꢂꢇꢍ3ꢇꢒꢃꢄꢒꢅꢑꢔꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢔ144)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢔꢁꢍꢌ&4ꢔꢇꢍ3ꢇꢒꢃꢄꢒ
DS22182A-page 24
© 2009 Microchip Technology Inc.
MCP6051/2/4
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆ'ꢐꢄꢈꢆ(ꢈꢄꢊꢘꢆꢓꢖꢆꢂꢃꢄꢅꢆꢇꢄꢌ)ꢄ*ꢃꢆꢒ+ꢓꢔꢆMꢆ,-ꢙ-ꢜꢚ./ꢆꢎꢎꢆ ꢖꢅ!ꢆ"0'(ꢓ%
ꢓꢖꢊꢃ& 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢔꢇꢍ3ꢇꢒꢉꢅ"ꢊꢇ)ꢃꢄꢒ 'ꢅꢔꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢕꢃꢍꢊꢌꢍꢎꢃꢔꢅꢂꢇꢍ3ꢇꢒꢃꢄꢒꢅꢑꢔꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢔ144)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢔꢁꢍꢌ&4ꢔꢇꢍ3ꢇꢒꢃꢄꢒ
© 2009 Microchip Technology Inc.
DS22182A-page 25
MCP6051/2/4
12ꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢈꢆꢏꢐꢊꢈꢋꢑꢃꢆꢒꢍꢂꢔꢆMꢆꢓꢄꢕꢕꢖꢗꢘꢆꢙꢚꢛꢜꢆꢎꢎꢆ ꢖꢅ!ꢆ"ꢍꢏ#$%
ꢓꢖꢊꢃ& 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢔꢇꢍ3ꢇꢒꢉꢅ"ꢊꢇ)ꢃꢄꢒ 'ꢅꢔꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢕꢃꢍꢊꢌꢍꢎꢃꢔꢅꢂꢇꢍ3ꢇꢒꢃꢄꢒꢅꢑꢔꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢔ144)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢔꢁꢍꢌ&4ꢔꢇꢍ3ꢇꢒꢃꢄꢒ
D
N
E
E1
NOTE 1
1
2
3
e
h
b
α
h
c
φ
A2
A
L
A1
β
L1
5ꢄꢃ%
ꢕꢛ66ꢛꢕ-ꢙ-ꢚꢑ
ꢓꢃ&ꢉꢄ ꢃꢌꢄꢅ6ꢃ&ꢃ%
ꢕꢛ7
78ꢕ
ꢕꢘ9
7!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
7
ꢉ
ꢀꢗ
ꢀꢁꢏꢜꢅ0ꢑ+
8ꢆꢉꢊꢇꢈꢈꢅ;ꢉꢃꢒꢎ%
ꢕꢌꢈ"ꢉ"ꢅꢂꢇꢍ3ꢇꢒꢉꢅꢙꢎꢃꢍ3ꢄꢉ
ꢑ%ꢇꢄ"ꢌ$$ꢅꢅꢐ
ꢘ
M
ꢀꢁꢏ.
ꢖꢁꢀꢖ
M
M
M
ꢀꢁꢜ.
M
ꢖꢁꢏ.
ꢘꢏ
ꢘꢀ
-
8ꢆꢉꢊꢇꢈꢈꢅ=ꢃ"%ꢎ
>ꢁꢖꢖꢅ0ꢑ+
ꢕꢌꢈ"ꢉ"ꢅꢂꢇꢍ3ꢇꢒꢉꢅ=ꢃ"%ꢎ
8ꢆꢉꢊꢇꢈꢈꢅ6ꢉꢄꢒ%ꢎ
+ꢎꢇ&$ꢉꢊꢅ?ꢌꢔ%ꢃꢌꢄꢇꢈ@
2ꢌꢌ%ꢅ6ꢉꢄꢒ%ꢎ
-ꢀ
ꢓ
ꢎ
,ꢁꢝꢖꢅ0ꢑ+
:ꢁ>.ꢅ0ꢑ+
ꢖꢁꢏ.
ꢖꢁꢗꢖ
M
M
ꢖꢁ.ꢖ
ꢀꢁꢏꢜ
6
2ꢌꢌ%ꢔꢊꢃꢄ%
2ꢌꢌ%ꢅꢘꢄꢒꢈꢉ
6ꢉꢇ"ꢅꢙꢎꢃꢍ3ꢄꢉ
6ꢉꢇ"ꢅ=ꢃ"%ꢎ
ꢕꢌꢈ"ꢅꢓꢊꢇ$%ꢅꢘꢄꢒꢈꢉꢅꢙꢌꢔ
ꢕꢌꢈ"ꢅꢓꢊꢇ$%ꢅꢘꢄꢒꢈꢉꢅ0ꢌ%%ꢌ&
6ꢀ
ꢀ
ꢀꢁꢖꢗꢅꢚ-2
ꢖꢞ
ꢖꢁꢀꢜ
ꢖꢁ,ꢀ
.ꢞ
M
M
M
M
M
:ꢞ
ꢍ
(
ꢁ
ꢖꢁꢏ.
ꢖꢁ.ꢀ
ꢀ.ꢞ
ꢂ
.ꢞ
ꢀ.ꢞ
ꢓꢖꢊꢃꢉ&
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢐꢅꢑꢃꢒꢄꢃ$ꢃꢍꢇꢄ%ꢅ+ꢎꢇꢊꢇꢍ%ꢉꢊꢃ %ꢃꢍꢁ
,ꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄ ꢅꢓꢅꢇꢄ"ꢅ-ꢀꢅ"ꢌꢅꢄꢌ%ꢅꢃꢄꢍꢈ!"ꢉꢅ&ꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢔꢊꢌ%ꢊ! ꢃꢌꢄ ꢁꢅꢕꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢔꢊꢌ%ꢊ! ꢃꢌꢄ ꢅ ꢎꢇꢈꢈꢅꢄꢌ%ꢅꢉ#ꢍꢉꢉ"ꢅꢖꢁꢀ.ꢅ&&ꢅꢔꢉꢊꢅ ꢃ"ꢉꢁ
ꢗꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢒꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢒꢅꢔꢉꢊꢅꢘꢑꢕ-ꢅ/ꢀꢗꢁ.ꢕꢁ
0ꢑ+1 0ꢇ ꢃꢍꢅꢓꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢙꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢚ-21 ꢚꢉ$ꢉꢊꢉꢄꢍꢉꢅꢓꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢔ!ꢊꢔꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢕꢃꢍꢊꢌꢍꢎꢃꢔ ꢙꢉꢍꢎꢄꢌꢈꢌꢒꢋ ꢓꢊꢇ)ꢃꢄꢒ +ꢖꢗꢟꢖ>.0
DS22182A-page 26
© 2009 Microchip Technology Inc.
MCP6051/2/4
ꢓꢖꢊꢃ& 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢔꢇꢍ3ꢇꢒꢉꢅ"ꢊꢇ)ꢃꢄꢒ 'ꢅꢔꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢕꢃꢍꢊꢌꢍꢎꢃꢔꢅꢂꢇꢍ3ꢇꢒꢃꢄꢒꢅꢑꢔꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢔ144)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢔꢁꢍꢌ&4ꢔꢇꢍ3ꢇꢒꢃꢄꢒ
© 2009 Microchip Technology Inc.
DS22182A-page 27
MCP6051/2/4
12ꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆ03ꢋꢑꢆꢍ3ꢕꢋꢑ)ꢆꢍꢎꢄꢈꢈꢆꢏꢐꢊꢈꢋꢑꢃꢆꢒꢍ0ꢔꢆMꢆ2ꢚ2ꢆꢎꢎꢆ ꢖꢅ!ꢆ"0ꢍꢍꢏꢇ%
ꢓꢖꢊꢃ& 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢔꢇꢍ3ꢇꢒꢉꢅ"ꢊꢇ)ꢃꢄꢒ 'ꢅꢔꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢕꢃꢍꢊꢌꢍꢎꢃꢔꢅꢂꢇꢍ3ꢇꢒꢃꢄꢒꢅꢑꢔꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢔ144)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢔꢁꢍꢌ&4ꢔꢇꢍ3ꢇꢒꢃꢄꢒ
D
N
E
E1
NOTE 1
1
2
e
b
c
φ
A2
A
A1
L
L1
5ꢄꢃ%
ꢕꢛ66ꢛꢕ-ꢙ-ꢚꢑ
ꢓꢃ&ꢉꢄ ꢃꢌꢄꢅ6ꢃ&ꢃ%
ꢕꢛ7
78ꢕ
ꢕꢘ9
7!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
7
ꢉ
ꢀꢗ
ꢖꢁ>.ꢅ0ꢑ+
8ꢆꢉꢊꢇꢈꢈꢅ;ꢉꢃꢒꢎ%
ꢕꢌꢈ"ꢉ"ꢅꢂꢇꢍ3ꢇꢒꢉꢅꢙꢎꢃꢍ3ꢄꢉ
ꢑ%ꢇꢄ"ꢌ$$ꢅ
8ꢆꢉꢊꢇꢈꢈꢅ=ꢃ"%ꢎ
ꢕꢌꢈ"ꢉ"ꢅꢂꢇꢍ3ꢇꢒꢉꢅ=ꢃ"%ꢎ
ꢕꢌꢈ"ꢉ"ꢅꢂꢇꢍ3ꢇꢒꢉꢅ6ꢉꢄꢒ%ꢎ
2ꢌꢌ%ꢅ6ꢉꢄꢒ%ꢎ
ꢘ
M
ꢖꢁ:ꢖ
ꢖꢁꢖ.
M
ꢀꢁꢖꢖ
M
>ꢁꢗꢖꢅ0ꢑ+
ꢗꢁꢗꢖ
.ꢁꢖꢖ
ꢖꢁ>ꢖ
ꢀꢁꢏꢖ
ꢀꢁꢖ.
ꢖꢁꢀ.
ꢘꢏ
ꢘꢀ
-
-ꢀ
ꢓ
ꢗꢁ,ꢖ
ꢗꢁꢝꢖ
ꢖꢁꢗ.
ꢗꢁ.ꢖ
.ꢁꢀꢖ
ꢖꢁꢜ.
6
2ꢌꢌ%ꢔꢊꢃꢄ%
2ꢌꢌ%ꢅꢘꢄꢒꢈꢉ
6ꢉꢇ"ꢅꢙꢎꢃꢍ3ꢄꢉ
6ꢉꢇ"ꢅ=ꢃ"%ꢎ
6ꢀ
ꢀ
ꢀꢁꢖꢖꢅꢚ-2
ꢖꢞ
ꢖꢁꢖꢝ
ꢖꢁꢀꢝ
M
M
M
:ꢞ
ꢍ
(
ꢖꢁꢏꢖ
ꢖꢁ,ꢖ
ꢓꢖꢊꢃꢉ&
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄ ꢅꢓꢅꢇꢄ"ꢅ-ꢀꢅ"ꢌꢅꢄꢌ%ꢅꢃꢄꢍꢈ!"ꢉꢅ&ꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢔꢊꢌ%ꢊ! ꢃꢌꢄ ꢁꢅꢕꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢔꢊꢌ%ꢊ! ꢃꢌꢄ ꢅ ꢎꢇꢈꢈꢅꢄꢌ%ꢅꢉ#ꢍꢉꢉ"ꢅꢖꢁꢀ.ꢅ&&ꢅꢔꢉꢊꢅ ꢃ"ꢉꢁ
,ꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢒꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢒꢅꢔꢉꢊꢅꢘꢑꢕ-ꢅ/ꢀꢗꢁ.ꢕꢁ
0ꢑ+1 0ꢇ ꢃꢍꢅꢓꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢙꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢚ-21 ꢚꢉ$ꢉꢊꢉꢄꢍꢉꢅꢓꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢔ!ꢊꢔꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢕꢃꢍꢊꢌꢍꢎꢃꢔ ꢙꢉꢍꢎꢄꢌꢈꢌꢒꢋ ꢓꢊꢇ)ꢃꢄꢒ +ꢖꢗꢟꢖ:ꢜ0
DS22182A-page 28
© 2009 Microchip Technology Inc.
MCP6051/2/4
APPENDIX A: REVISION HISTORY
Revision A (May 2009)
• Original Release of this Document.
© 2009 Microchip Technology Inc.
DS22182A-page 29
MCP6051/2/4
NOTES:
DS22182A-page 30
© 2009 Microchip Technology Inc.
MCP6051/2/4
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
X
/XX
Examples:
Temperature
Range
Package
a)
b)
MCP6051-E/SN:
8LD SOIC package
Tape and Reel,
MCP6051T-E/SN:
8LD SOIC package
8LD 2x3 TDFN package
c)
d)
MCP6051-E/MNY:
Device:
MCP6051:
MCP6051T:
Single Op Amp
MCP6051T-E/MNY: Tape and Reel,
8LD 2x3 TDFN package
Single Op Amp (Tape and Reel)
(SOIC and 2x3 TDFN)
Dual Op Amp
MCP6052:
MCP6052T:
Dual Op Amp (Tape and Reel)
(SOIC and 2x3 TDFN)
Quad Op Amp
Quad Op Amp (Tape and Reel)
(SOIC and TSSOP)
a)
b)
MCP6052-E/SN:
MCP6052T-E/SN:
8LD SOIC package
Tape and Reel,
8LD SOIC package
8LD 2x3 TDFN package
MCP6054:
MCP6054T:
c)
d)
MCP6052-E/MNY:
MCP6052T-E/MNY: Tape and Reel
8LD 2x3 TDFN package
Temperature Range:
Package:
E
= -40°C to +125°C
a)
b)
MCP6054-E/SL:
MCP6054T-E/SL:
14LD SOIC package
Tape and Reel,
MNY *
= Plastic Dual Flat, No Lead, (2x3 TDFN ) 8-lead
SL
SN
ST
=
=
=
Plastic SOIC (150 mil Body), 14-lead
Plastic SOIC, (150 mil Body), 8-lead
Plastic TSSOP (4.4mm Body), 14-lead
14LD SOIC package
14LD TSSOP package
Tape and Reel,
c)
d)
MCP6054-E/ST:
MCP6054T-E/ST:
* Y = Nickel palladium gold manufacturing designator. Only
available on the TDFN package.
14LD TSSOP package
© 2009 Microchip Technology Inc.
DS22182A-page 31
MCP6051/2/4
NOTES:
DS22182A-page 32
© 2009 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, rfPIC, SmartShunt and UNI/O are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
FilterLab, Hampshire, Linear Active Thermistor, MXDEV,
MXLAB, SEEVAL, SmartSensor and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, In-Circuit Serial
Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, nanoWatt XLP,
PICkit, PICDEM, PICDEM.net, PICtail, PIC32 logo, PowerCal,
PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select
Mode, Total Endurance, TSHARC, WiperLock and ZENA are
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2009, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2009 Microchip Technology Inc.
DS22182A-page 33
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4080
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Boston
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Seoul
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Cleveland
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Detroit
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-6578-300
Fax: 886-3-6578-370
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Santa Clara
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
03/26/09
DS22182A-page 34
© 2009 Microchip Technology Inc.
MCP6052T 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
MCP6052T-E/MNY | MICROCHIP | 30 μA, High Precision Op Amps | 获取价格 | |
MCP6052T-E/SL | MICROCHIP | 30 μA, High Precision Op Amps | 获取价格 | |
MCP6052T-E/SN | MICROCHIP | 30 μA, High Precision Op Amps | 获取价格 | |
MCP6052T-E/ST | MICROCHIP | 30 μA, High Precision Op Amps | 获取价格 | |
MCP6054 | MICROCHIP | 30 μA, High Precision Op Amps | 获取价格 | |
MCP6054-E/MNY | MICROCHIP | 30 μA, High Precision Op Amps | 获取价格 | |
MCP6054-E/SL | MICROCHIP | 30 μA, High Precision Op Amps | 获取价格 | |
MCP6054-E/SN | MICROCHIP | 30 μA, High Precision Op Amps | 获取价格 | |
MCP6054-E/ST | MICROCHIP | 30 μA, High Precision Op Amps | 获取价格 | |
MCP6054T | MICROCHIP | 30 μA, High Precision Op Amps | 获取价格 |
MCP6052T 相关文章
- 2024-09-20
- 5
- 2024-09-20
- 8
- 2024-09-20
- 8
- 2024-09-20
- 6