MCP73837T-G8I/UN [MICROCHIP]
1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10, PLASTIC, MSOP-10;型号: | MCP73837T-G8I/UN |
厂家: | MICROCHIP |
描述: | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10, PLASTIC, MSOP-10 光电二极管 |
文件: | 总34页 (文件大小:1170K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MCP73837/8
Advanced Stand-Alone Li-Ion / Li-Polymer Battery Charge
Management Controller with Autonomous AC-Adapter or
USB-Port Source Selection
Features
Applications
• High Accuracy Preset Voltage Regulation: + 0.5%
• Available Voltage Regulation Options:
- 4.20V, 4.35V, 4.4V, or 4.5V
• Smart Phones and Personal Data Assistants
(PDA)
• Portable Media Players (PMP)
• Ultra Mobile Devices (UMD)
• Digital Cameras
• Complete Linear Charge Management Controller:
- Autonomous Power Source Selection
- Integrated Pass Transistors
• MP3 Players
• Bluetooth Headsets
- Integrated Current Sense
• Handheld Medical Devices
• AC/USB Dual Source Li-Ion Battery Chargers
- Integrated Reverse Discharge Protection
• Constant Current (CC) / Constant Voltage (CV)
Operation with Thermal Regulation
Description
• Selectable USB-Port Charge Current:
- Low: 1 Unit Load / High: 5 Unit Loads
• Programmable AC-Adapter Charge Current:
- 15 mA - 1000 mA
The MCP73837 and MCP73838 devices are fully
integrated linear Li-Ion / Li-Polymer battery chargers
with autonomous power source selection. Along with its
small physical size, the low number of external
components required makes the MCP73837/8 ideally
suitable for portable applications.
• Two Charge Status Outputs
• Power-Good Monitor: MCP73837
• Timer Enable: MCP73838
The MCP73837/8 automatically selects the USB-port
or AC-adapter as the power source for the system. For
the USB-port powered systems, the MCP73837/8
specifically adheres to the current limits governed by
the USB specification. The host microcontroller can
select from two preset maximum charge current rates
of 100 mA (low power USB-port) or 500 mA (high
power USB-port). With an AC-adapter providing power
to the system, an external resistor sets the magnitude
of the system or charge current up to a maximum of 1A.
• Automatic Recharge:
- Selectable Voltage Threshold
• Automatic End-of-Charge Control:
- Selectable Charge Termination Current Ratio
- Selectable Safety Timer Period
• Preconditioning of Deeply Depleted Cells - Can
Be Disabled
• Battery Cell Temperature Monitor
• UVLO (Undervoltage Lockout)
The MCP73837/8 employs a constant current/constant
voltage
charge
algorithm
with
selectable
• Automatic Power-Down when Input Power is
Removed
preconditioning and charge termination. The constant
voltage regulation is fixed with four available options:
4.20V, 4.35V, 4.40V, or 4.50V, to accommodate the
new emerging battery charging requirements. The
MCP73837/8 limits the charge current, based on die
temperature, during high power or high ambient
conditions. This thermal regulation optimizes the
charge cycle time while maintaining the device
reliability.
• Low-Dropout (LDO) Linear Regulator Mode
• Numerous Selectable Options Available for a
Variety of Applications:
- Refer to Section 1.0 “Electrical
Characteristics” for Selectable Options
- Refer to the “Product Identification
System” for Standard Options
• Temperature Range: -40°C to 85°C
• Packaging:
The MCP73837/8 are fully specified over the ambient
temperature range of -40°C to +85°C.
- 10-Lead 3 mm x 3 mm DFN
The MCP73837/8 devices are available in a 10-Lead,
3 mm x 3 mm, DFN package or in a 10-Lead MSOP
package.
- 10-Lead MSOP*
* Consult Factory for MSOP package
availability.
© 2007-2011 Microchip Technology Inc.
DS22071B-page 1
MCP73837/8
Package Types
MCP73837/8
10-Lead DFN 3 mm x 3 mm
MCP73837/8
10-Lead MSOP
VBAT
VAC
VAC
VBAT
1
2
1
2
3
4
5
10
9
10
9
VUSB
VUSB
THERM
PG (TE)
PROG2
PROG1
THERM
PG (TE)
PROG2
STAT1 3
STAT2 4
8
8
STAT1
STAT2
VSS
7
7
VSS
5
6
6
PROG1
Typical Applications
MCP73837 Typical Application
1
10
VBAT
Ac-dc Adapter
VAC
Thermsitor
4.7 µF
Single
Li-Ion
Cell
9
2
USB Port
4.7 µF
VUSB
THERM
4.7 µF
1 kΩ
3
5
VSS
STAT1
1 kΩ
4
7
STAT2
PROG2
Hi
Low
1 kΩ
8
6
PG
PROG1
RPROG
MCP73838 Typical Application
1
10
Ac-dc Adapter
VAC
VBAT
Thermsitor
9
4.7 µF
2
USB Port
4.7 µF
VUSB
THERM
TE
Cell
4.7 µF
1KΩ
3
8
STAT1
Hi
Hi
Low
Low
1KΩ
4
7
6
STAT2
PROG2
PROG1
5
VSS
RPROG
DS22071B-page 2
© 2007-2011 Microchip Technology Inc.
MCP73837/8
Functional Block Diagram (MCP73837/8)
VO
REG
DIRECTION
CONTROL
6μA
V
V
BAT
USB
SENSEFET
G=0.001
100mA/500mA
10k
2k
SENSEFET
G=0.001
VO
REG
DIRECTION
CONTROL
V
AC
AC/USB
CURRENT
LIMIT
+
-
SENSEFET
G=0.001
1k
V
REF
SENSEFET
G=0.001
PROG1
AC/USB
111k
CA
+
-
REFERENCE,
BIAS, UVLO,
AND SHDN
V
(1.21V)
REF
310k
10k
+
-
VO
UVLO
REG
72.7k
-
470.6k
PRECONDITION
+
TERM
48k
-
PROG2
STAT1
+
CHARGE
6k
CHARGE
CONTROL,
TIMER,
AND
VA
+
-
157.3k
STATUS
LOGIC
VO
REG
STAT2
+
-
LDO
HTVT
LTVT
175k
PG (TE)
+
-
50μA
470.6k
121k
THERM
+
-
175k
V
SS
1M
© 2007-2011 Microchip Technology Inc.
DS22071B-page 3
MCP73837/8
† Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
1.0
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings†
VDDN ................................................................................7.0V
All Inputs and Outputs w.r.t. V ............... -0.3 to (V +0.3)V
SS
DD
Maximum Junction Temperature, T ............Internally Limited
J
Storage temperature .....................................-65°C to +150°C
ESD protection on all pins
Human Body Model (1.5 kW in Series with 100 pF) ......≥ 4 kV
Machine Model (200 pF, No Series Resistance).............300V
DC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, all limits apply for V = [V
(typical) + 0.3V] to 6V,
DD
REG
T = -40°C to +85°C. Typical values are at +25°C, V = [V
(typical) + 1.0V]
A
DD
REG
Parameters
Sym
Min
Typ
Max
Units
Conditions
Supply Input
Supply Voltage
V
V
(Typ)
—
6
V
Note 1
DD
REG
+0.3V
Supply Current
I
—
1900
110
75
3000
300
100
5
µA
µA
µA
µA
Charging
SS
Charge Complete, No Battery
Standby (PROG Floating)
—
—
0.6
Shutdown (V < V
-
BAT
DD
100 mV or V < V
)
STOP
DD
UVLO Start Threshold
UVLO Stop Threshold
UVLO Hysteresis
V
V
3.35
3.25
—
3.45
3.35
75
3.55
3.45
—
V
V
V
V
= Low to High (USB-port)
START
DD
DD
V
= High to Low (USB-port)
STOP
V
mV (USB-port)
HYS
UVLO Start Threshold
UVLO Stop Threshold
UVLO Hysteresis
4.1
4.0
—
4.15
4.1
4.3
4.2
—
V
V
(AC-adapter)
(AC-adapter)
START
V
STOP
V
55
mV (AC-adapter)
HYS
Voltage Regulation (Constant Voltage Mode)
Regulated Charge Voltage
V
4.179
4.328
4.378
4.477
-0.5
4.20
4.35
4.40
4.50
—
4.221
4.372
4.422
4.523
+0.5
V
V
V
=[V
(typical)+1V]
REG
DD
REG
I
=30 mA
OUT
V
T =-5°C to +55°C
A
V
Regulated Charge Voltage Tolerance
Line Regulation
V
%
T =-5°C to +55°C
A
RTOL
|(ΔV
/
—
0.075
0.2
%/V
V
I
=[V
(typical)+1V] to 6V
BAT
DD
REG
V
)/ΔV
|
=30 mA
BAT
DD
OUT
Load Regulation
|ΔV
/V
|
—
0.150
0.3
%
I
=10 mA to 100 mA
BAT BAT
OUT
V
=[V
(typical)+1V]
DD
OUT
OUT
OUT
REG
Supply Ripple Attenuation
PSRR
—
—
—
60
52
23
—
—
—
dB
dB
dB
I
I
I
=10 mA, 10Hz to 1 kHz
=10 mA, 10Hz to 10 kHz
=10 mA, 10Hz to 1 MHz
Current Regulation (Fast Charge Constant-Current Mode)
AC-adapter Fast Charge Current
I
95
105
115
mA PROG1 = 10 kΩ
REG
900
1000
1100
mA PROG1 = 1 kΩ, Note 2
T =-5°C to +55°C
A
Note 1: The supply voltage (V ) = V when input power source is from AC-adapter and the supply voltage (V ) = V
USB
DD
AC
DD
when input power source is from USB-port.
2: The value is guaranteed by design and not production tested.
3: The current is based on the ratio of selected current regulation (I
).
REG
4: The maximum charge impedance has to be less than shutdown impedance for normal operation.
DS22071B-page 4
© 2007-2011 Microchip Technology Inc.
MCP73837/8
DC CHARACTERISTICS (Continued)
Electrical Specifications: Unless otherwise indicated, all limits apply for V = [V
(typical) + 0.3V] to 6V,
DD
REG
T = -40°C to +85°C. Typical values are at +25°C, V = [V
(typical) + 1.0V]
A
DD
REG
Parameters
Sym
Min
Typ
Max
Units
Conditions
USB-port Fast Charge Current
I
80
90
100
500
mA PROG2 = Low
mA PROG2 = High
REG
400
450
T =-5°C to +55°C
A
Maximum Output Current Limit
I
—
1200
—
mA PROG1 < 833Ω
MAX
Precondition Current Regulation (Trickle Charge Constant-Current Mode)
Precondition Current Ratio
I
/ I
7.5
15
30
10
20
12.5
25
%
%
Note 3
T =-5°C to +55°C
PREG REG
A
40
50
%
100
66.5
71.5
120
%
Precondition Current Threshold Ratio
V
I
/ V
64
69
—
69
74
—
%
V
V
Low to High
High to Low
PTH
REG
BAT
BAT
%
Precondition Hysteresis
V
mV
PHYS
Charge Termination
Charge Termination Current Ratio
/ I
3.75
5.6
7.5
15
5
6.25
9.4
%
%
%
%
PROG1 = 1 kΩ to 10 kΩ
TERM REG
7.5
10
20
T =-5°C to +55°C
A
12.5
25
Note 3
Automatic Recharge
Recharge Voltage Threshold Ratio
V
/ V
92
95
94.0
97
96
99
%
%
V
High to Low
BAT
RTH
REG
T =-5°C to +55°C
A
Pass Transistor ON-Resistance
ON-Resistance
R
—
350
—
mΩ
V
= 4.5V, T = 105°C
DSON
DD J
Battery Discharge Current
Output Reverse Leakage Current
I
—
—
—
0.1
0.55
-6
2
2
µA
µA
µA
Standby (PROG1 or PROG2
Floating)
DISCHARGE
Shutdown (V < V
-
BAT
DD
100 mV or V < V
)
STOP
DD
-15
Charge Complete
Status Indicators - STAT1, STAT2, PG (MCP73837)
Sink Current
I
—
—
—
16
0.3
35
1
mA
V
SINK
Low Output Voltage
Input Leakage Current
PROG1 Input (PROG1)
Charge Impedance Range
Shutdown Impedance
V
I
= 4 mA
OL
SINK
I
0.03
1
µA
High Impedance, V on pin
LK
DD
R
R
1
—
—
—
kΩ
kΩ
Note 4
PROG
PROG
70
200
Minimum Impedance for
Shutdown
PROG2 Inputs (PROG2)
Input High Voltage Level
Input Low Voltage Level
Shutdown Voltage Level
Input Leakage Current
V
0.8V
—
—
—
7
—
%
%
IH
DD
V
—
0.2V
—
0.2V
IL
DD
DD
V
0.8V
15
%
SD
LK
DD
I
µA
V
= V
PROG2 DD
Note 1: The supply voltage (V ) = V when input power source is from AC-adapter and the supply voltage (V ) = V
USB
DD
AC
DD
when input power source is from USB-port.
2: The value is guaranteed by design and not production tested.
3: The current is based on the ratio of selected current regulation (I
).
REG
4: The maximum charge impedance has to be less than shutdown impedance for normal operation.
© 2007-2011 Microchip Technology Inc.
DS22071B-page 5
MCP73837/8
DC CHARACTERISTICS (Continued)
Electrical Specifications: Unless otherwise indicated, all limits apply for V = [V
(typical) + 0.3V] to 6V,
DD
REG
T = -40°C to +85°C. Typical values are at +25°C, V = [V
(typical) + 1.0V]
A
DD
REG
Parameters
Sym
Min
Typ
Max
Units
Conditions
Timer Enable (TE)
Input High Voltage Level
Input Low Voltage Level
Input Leakage Current
Thermistor Bias
V
2
—
—
—
V
V
IH
V
—
—
0.8
1
IL
I
0.01
µA
V
= V
LK
TE DD
Thermistor Current Source
Thermistor Comparator
Upper Trip Threshold
I
47
50
53
µA
2 kΩ < R
< 50 kΩ
THERM
THERM
V
1.20
—
1.23
-40
1.26
—
V
mV
V
V
V
Low to High
High to Low
T1
T1
T2
Upper Trip Point Hysteresis
Lower Trip Threshold
V
V
T1HYS
V
0.235
—
0.250
40
0.265
—
T2
Lower Trip Point Hysteresis
System Test (LDO) Mode
Input High Voltage Level
THERM Input Sink Current
mV
T2HYS
V
—
3
—
V
- 0.1
DD
V
IH
I
5.5
20
µA
Stand-by or System Test
Mode
SINK
Bypass Capacitance
C
1
4.7
—
—
µF
µF
I
I
< 250 mA
> 250 mA
BAT
OUT
OUT
Automatic Power Down (SLEEP Comparator, Direction Control)
Automatic Power Down Entry
Threshold
V
V
+
V
+
—
V
V
2.3V < V
< V
< V
PD
BAT
BAT
BAT
REG
REG
10 mV
100 mV
V
Falling
DD
Automatic Power Down Exit Threshold
V
-
V
+
V
+
2.3V < V
BAT
PDEXIT
BAT
BAT
150 mV 250 mV
V
Rising
DD
Thermal Shutdown
Die Temperature
T
—
—
150
10
—
—
°C
°C
SD
Die Temperature Hysteresis
T
SDHYS
Note 1: The supply voltage (V ) = V when input power source is from AC-adapter and the supply voltage (V ) = V
USB
DD
AC
DD
when input power source is from USB-port.
2: The value is guaranteed by design and not production tested.
3: The current is based on the ratio of selected current regulation (I
).
REG
4: The maximum charge impedance has to be less than shutdown impedance for normal operation.
DS22071B-page 6
© 2007-2011 Microchip Technology Inc.
MCP73837/8
AC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, all limits apply for V = [V
(typical) + 0.3V] to 6V.
REG
DD
Typical values are at +25°C, V = [V
(typical) + 1.0V]
DD
REG
Parameters
Sym
Min
Typ
Max
Units
Conditions
Low to High
UVLO Start Delay
t
t
—
—
5
ms
V
V
START
DD
Current Regulation
Transition Time Out of Precondition
—
—
—
—
10
10
ms
ms
ms
ms
ms
ms
< V
to V
> V
DELAY
BAT
PTH
BAT PTH
Current Rise Time Out of Precondition
Precondition Comparator Filter Time
Termination Comparator Filter Time
Charge Comparator Filter Time
Thermistor Comparator Filter Time
Elapsed Timer
t
I
Rising to 90% of I
OUT REG
RISE
t
t
0.4
0.4
0.4
0.4
1.3
1.3
1.3
1.3
3.2
3.2
3.2
3.2
Average V
Rise/Fall
BAT
PRECON
t
Average I
Falling
Falling
TERM
CHARGE
OUT
Average V
BAT
t
Average THERM Rise/Fall
THERM
Elapsed Timer Period
t
0
0
0
Hours Timer Disabled
ELAPSED
3.6
5.4
7.2
4.0
6.0
8.0
4.4
6.6
8.8
Hours
Hours
Hours
Status Indicators
Status Output Turn-off
Status Output Turn-on
t
—
—
—
—
500
500
µs
µs
I
I
= 1 mA to 0 mA
= 0 mA to 1 mA
OFF
SINK
SINK
t
ON
TEMPERATURE SPECIFICATIONS
Electrical Specifications: Unless otherwise indicated, all limits apply for V = [V
(typ.) + 0.3V] to 6V.
REG
DD
Typical values are at +25°C, V = [V
(typ.) + 1.0V]
DD
REG
Parameters
Sym
Min
Typ
Max
Units
Conditions
Temperature Ranges
Specified Temperature Range
Operating Temperature Range
Storage Temperature Range
Thermal Package Resistances
Thermal Resistance, 10-Lead MSOP
T
-40
-40
-65
—
—
—
+85
+125
+150
°C
°C
°C
A
T
J
T
A
θ
θ
—
—
113
41
—
—
°C/W
°C/W
4-Layer JC51-7 Standard Board,
Natural Convection. Note 1
JA
Thermal Resistance, 10-Lead 3 mm x
3 mm DFN
4-Layer JC51-7 Standard Board,
Natural Convection
JA
Note 1: This represents the minimum copper condition on the PCB (Printed Circuit Board).
© 2007-2011 Microchip Technology Inc.
DS22071B-page 7
MCP73837/8
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, VDD = [VREG(typical) + 1V], IOUT = 30 mA, and TA= +25°C, Constant-voltage mode.
4.210
2.0
TEMP = 25°C
IOUT = 50 mA
4.205
4.200
4.195
4.190
4.185
4.180
4.175
4.170
4.165
4.160
VDD = Floating
VBAT = 4.2V
IOUT = 10 mA
1.6
1.2
0.8
0.4
0.0
IOUT = 100 mA
IOUT = 500 mA
IOUT = 1000 mA
-40 -30 -20 -10
0
10 20 30 40 50 60 70 80
Temperature (°C)
4.5
4.8
5.0
5.3
5.5
5.8
6.0
Supply Voltage (V)
FIGURE 2-1:
Battery Regulation Voltage
FIGURE 2-4:
Output Leakage Current
(VBAT) vs. Supply Voltage (VDD).
(IDISCHARGE) vs. Ambient Temperature (TA).
2.0
4.210
VDD = 5.2V
VDD = Floating
1.8
IOUT = 10 mA
4.205
4.200
4.195
4.190
4.185
4.180
4.175
4.170
IOUT = 50 mA
TEMP = +25°C
1.6
1.4
1.2
1.0
IOUT = 100 mA
IOUT = 500 mA
0.8
0.6
IOUT = 1000 mA
0.4
0.2
0.0
3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2
-40 -30 -20 -10
0 10 20 30 40 50 60 70 80
Battery Voltage (V)
Ambient Temperature (°C)
FIGURE 2-2:
Battery Regulation Voltage
FIGURE 2-5:
Output Leakage Current
(VBAT) vs. Ambient Temperature (TA).
(IDISCHARGE) vs. Battery Voltage (VBAT).
0.50
0.45
1000
VDD = VBAT
TEMP = 25 °C
VDD = 5.2V
Temp = 25°C
900
800
700
600
500
400
300
200
100
0
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0.00
3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2
Battery Voltage (V)
1
6
11 16 21 26 31 36 41 46 51 56 61
RPROG (kΩ)
FIGURE 2-3:
Output Leakage Current
FIGURE 2-6:
Charge Current (IOUT) vs.
(IDISCHARGE) vs. Battery Regulation Voltage
(VBAT).
Programming Resistor (RPROG).
DS22071B-page 8
© 2007-2011 Microchip Technology Inc.
MCP73837/8
Note: Unless otherwise indicated, VDD = [VREG(typical) + 1V], IOUT = 30 mA and TA= +25°C, Constant-voltage mode.
110
108
106
104
102
100
98
1200
1150
1100
1050
1000
950
RPROG = 10 kΩ
DD = 5.2V
RPROG = 1 kΩ
Temp = +25°C
V
900
96
850
94
800
750
92
700
90
-40 -30 -20 -10
0
10 20 30 40 50 60 70 80
4.5
4.8
5.0
5.3
5.5
5.8
6.0
Ambient Temperature (°C)
Supply Voltage (V)
FIGURE 2-7:
Charge Current (IOUT) vs.
FIGURE 2-10:
Charge Current (IOUT) vs.
Supply Voltage (VDD).
Ambient Temperature (TA).
55
54
53
52
51
50
49
48
47
46
45
104
102
100
98
RPROG = 20 kΩ
DD = 5.2V
RPROG = 10 kΩ
Temp = +25°C
V
96
94
92
90
4.5
4.8
5.0
5.3
5.5
5.8
6.0
-40 -30 -20 -10
0
10 20 30 40 50 60 70 80
Supply Voltage (V)
Ambient Temperature (°C)
FIGURE 2-8:
Charge Current (IOUT) vs.
FIGURE 2-11:
Charge Current (IOUT) vs.
Supply Voltage (VDD).
Ambient Temperature (TA).
1100
1050
1000
950
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
RPROG = 1 kΩ
DD = 5.2V
RPROG = 1 kΩ
V
900
850
800
750
700
-40 -30 -20 -10
0 10 20 30 40 50 60 70 80
Ambient Temperature (°C)
Junction Temperature (°C)
FIGURE 2-9:
Charge Current (IOUT) vs.
FIGURE 2-12:
Charge Current (IOUT) vs.
Ambient Temperature (TA).
Junction Temperature (TJ).
© 2007-2011 Microchip Technology Inc.
DS22071B-page 9
MCP73837/8
Note: Unless otherwise indicated, VDD = [VREG(typical) + 1V], IOUT = 30 mA and TA= +25°C, Constant-voltage mode.
600
52.0
51.5
51.0
50.5
50.0
49.5
49.0
48.5
48.0
47.5
47.0
RPROG = 2 kΩ
550
500
450
400
350
300
250
200
150
100
50
VDD = 5.2V
0
Junction Temperature (°C)
Ambient Temperature (°C)
FIGURE 2-13:
Charge Current (IOUT) vs.
FIGURE 2-16:
Thermistor Current (ITHERM)
Junction Temperature (TJ).
vs. Ambient Temperature (TA).
120
110
100
90
80
70
60
50
40
30
20
10
0
0
RPROG = 10 kΩ
IOUT = 10 mA
-10
-20
-30
-40
-50
-60
-70
C
OUT = 4.7 µF
0.01
0.1
1
10
100
1000
Frequency (kHz)
Junction Temperature (°C)
FIGURE 2-14:
Charge Current (IOUT) vs.
FIGURE 2-17:
Power Supply Ripple
Junction Temperature (TJ).
Rejection (PSRR).
0
52.0
51.5
51.0
50.5
50.0
49.5
49.0
48.5
48.0
47.5
47.0
Temp = +25°C
IOUT = 100 mA
COUT = 4.7 µF
-10
-20
-30
-40
-50
-60
-70
0.01
0.1
1
10
100
1000
4.5
4.8
5.0
5.3
5.5
5.8
6.0
Frequency (kHz)
Supply Voltage (V)
FIGURE 2-15:
Thermistor Current (ITHERM
)
FIGURE 2-18:
Power Supply Ripple
vs. Supply Voltage (VDD).
Rejection (PSRR).
DS22071B-page 10
© 2007-2011 Microchip Technology Inc.
MCP73837/8
Note: Unless otherwise indicated, VDD = [VREG(typical) + 1V], IOUT = 30 mA and TA= +25°C, Constant-voltage mode.
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0.1
0.05
0
-0.05
-0.1
-0.15
-0.2
-0.25
-0.3
16
14
12
10
8
0.1
0
IOUT = 100 mA
V
V
OUT
OUT
-0.1
-0.2
-0.3
-0.4
-0.5
V
IN
I
OUT
6
4
-0.1
2
IOUT = 100 mA
0
Time (Minutes)
Time (µs)
FIGURE 2-19:
Line Transient Response.
FIGURE 2-22:
Load Transient Response.
16
0.1
0
V
OUT
V
IN
14
12
10
8
-0.1
-0.2
-0.3
-0.4
-0.5
V
IN
6
4
V
OUT
2
IOUT = 10 mA
0
Time (µs)
FIGURE 2-20:
Line Transient Response.
FIGURE 2-23:
VAC Start Delay
(IOUT = 1A).
0.35
0.04
IOUT = 10 mA
0.02
V
OUT(AC)
0.3
0.25
0.2
0.15
0.1
V
IN
0
-0.02
-0.04
-0.06
-0.08
-0.1
I
OUT
0.05
0
-0.05
-0.12
V
OUT
Time (Minutes)
FIGURE 2-21:
Load Transient Response.
FIGURE 2-24:
VUSB Start Delay (USB =
Low).
© 2007-2011 Microchip Technology Inc.
DS22071B-page 11
MCP73837/8
Note: Unless otherwise indicated, VDD = [VREG(typical) + 1V], IOUT = 30 mA and TA= +25°C, Constant-voltage mode.
UVLOVAC
5.0
4.0
3.0
2.0
1.0
0.0
0.12
0.1
V
V
OUT
IN
0.08
0.06
0.04
0.02
0
I
OUT
VDD = 5.2V
RPROG = USB_Low
180 mAh Li-Ion Battery
V
OUT
0
20 40 60 80 100 120 140 160 180
Time (Minutes)
FIGURE 2-28:
(180 mAh Li-Ion Battery).
Complete Charge Cycle
FIGURE 2-25:
High)
VUSB Start Delay (USB =
5.0
0.12
0.1
5.0
V
1.2
1
V
OUT
C.C. Begins
OUT
4.0
3.0
2.0
4.0
3.0
2.0
1.0
0.0
I
OUT
0.08
0.06
0.04
0.02
0
0.8
I
OUT
0.6
C.V. Begins
0.4
0.2
VDD = 5.2V
RPROG = USB_Low
180 mAh Li-Ion Battery
VDD = 5.2V
1.0
0.0
RPROG = 1 kΩ
1200 mAh Li-Ion Battery
Preconditioning
0
0
1
2
3
4
5
6
7
8
9
10
Time (Minutes)
Time (Minutes)
FIGURE 2-29:
Preconditioning and CC-CV (180 mAh Li-Ion
Battery).
Typical Charge Profile in
FIGURE 2-26:
(1200 mAh Li-Ion Battery).
Complete Charge Cycle
4.5
1.2
0.9
0.6
0.3
0
V
OUT
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
I
OUT
VDD = 5.2V
RPROG = 1 kΩ
1200 mAh Li-Ion Battery
0
1
2
3
4
5
6
7
8
9
10
Time (Minutes)
FIGURE 2-27:
Typical Charge Profile in
Thermal Regulation (1200 mAh Li-Ion Battery).
DS22071B-page 12
© 2007-2011 Microchip Technology Inc.
MCP73837/8
3.0
PIN DESCRIPTION
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1: PIN FUNCTION TABLES
Pin Number
Symbol
I/O
Function
MSOP-10
DFN-10
1
2
3
4
5
6
1
2
3
4
5
6
VAC
VUSB
I
I
AC-adapter Supply Input
USB-port Supply Input
STAT1
STAT2
VSS
O
O
—
I/O
Charge Status Output 1 (Open-Drain)
Charge Status Output 2 (Open-Drain)
Battery Management 0V Reference
PROG1
Current Regulation Setting With AC-adapter; Device Charge Control
Enable; Precondition Set Point for AC control
7
7
PROG2
I
Current Regulation Setting With USB-port; Precondition Set Point
for USB control.
8
8
8
8
PG
TE
O
I
Available on MCP73837: Power-Good Status Output (Open-Drain)
Available on MCP73838: Timer Enable; Enables Safety Timer
(Active Low)
9
9
THERM
I/O
Thermistor Monitoring Input and Bias current; System Test (LDO)
Mode Input
10
—
10
VBAT
VSS
I/O
—
Battery Positive Input and Output Connection
EP
EP (Exposed Thermal Pad); There is an internal electrical
connection between the exposed thermal pad and VSS. The EP
must be connected to the same potential as the VSS pin on the
Printed Circuit Board (PCB).
3.1
AC-Adapter Supply Input (V
)
3.5
Battery Management 0V Reference
(V
AC
)
SS
A supply voltage of VREG + 0.3V to 6V from ac-dc wall-
adapter is recommended. When both the AC-adapter
and the USB-port supply voltages are present at the
same time, the AC-adapter dominates the regulated
charge current with the maximum value of 1A. Bypass
to VSS, with a minimum of 4.7 µF, is recommended.
Connect to the negative terminal of battery and input
supply.
3.6
Battery Charge Control Output
(V
)
BAT
Connect to the positive terminal of Li-Ion / Li-Polymer
batteries. Bypass to VSS, with a minimum of 1 µF, to
ensure loop stability when the battery is disconnected.
3.2
USB-Port Supply Input (V
)
USB
A supply voltage of VREG + 0.3V to 6V from the USB-
port is recommended. When no supply voltage from
VAC pin is available, the Li-Ion battery is charged
directly from USB-port. Bypass to VSS, with a minimum
of 1 µF, is recommended.
3.7
AC-Adapter Current Regulation
Set (PROG1)
The AC-adapter constant charge current is set by
placing a resistor from PROG1 to VSS. PROG1 is the
set point of precondition and termination when the AC-
adapter is present.
3.3
Charge Status Output 1 (STAT1)
STAT1 is an open-drain logic output for connection to a
LED for charge status indication. Alternatively, a pull-up
resistor can be applied for interfacing to a host micro-
controller.
PROG1 also functions as device charge control
enable. The MCP73837/8 is shut down when an
impedance value greater than 70 kΩ is applied to
PROG1. When PROG1 is floating, the MCP73837/8
enters Stand-by mode.
3.4
Charge Status Output 2 (STAT2)
STAT2 is an open-drain logic output for connection to a
LED for charge status indication. Alternatively, a pull-up
resistor can be applied for interfacing to a host
microcontroller.
© 2007-2011 Microchip Technology Inc.
DS22071B-page 13
MCP73837/8
3.8
USB-Port Current Regulation Set
(PROG2)
3.10 Timer Enable (TE)
Timer Enable (TE) is available only on MCP73838.
(TE) enables the built-in safety timer when pull low and
disables the built-in safety timer when pull high.
The MCP73837/8 USB-port current regulation set input
(PROG2) is a digital input selection. A logic Low selects
a 1 unit load charge current; a logic High selects a 5
unit loads charge current. The precondition and
termination current is internally set to the percentage
levels selected by the device part number. The current
is based upon the selected unit load charge current
based upon the level of PROG2.
Note:
The built-in safety timer is available for both
MCP73837 and MCP73838 in the following
options: Disable, 4 HR, 6 HR, and 8 HR.
3.11 Battery Temperature Monitor
(THERM)
PROG2 also functions as the set point of termination
when USB-port is present. When PROG2 is floating,
the MCP73837/8 enters in Stand-by mode.
MCP73837/8 continuously monitors the battery
temperature during a charge cycle by measuring the
voltage between the THERM and VSS pins. An internal
50 µA current source provides the bias for the most
common 10 kΩ negative-temperature coefficient
thermistors (NTC).
3.9
Power Good (PG)
Power Good (PG) is available only on MCP73837. PG
is an open-drain logic output for connection to an LED
for input power supply indication. Alternatively, a pull-
up resistor can be applied for interfacing to a host
microcontroller.
DS22071B-page 14
© 2007-2011 Microchip Technology Inc.
MCP73837/8
4.0
DEVICE OVERVIEW
The MCP73837/8 devices are simple, yet fully integrated linear charge management controllers. Figure 4-1 depicts the
operational flow algorithm.
SHUTDOWN MODE*
* Continuously Monitored
V
< V
-100 mV
DD
BAT
< V
V
DD
STOP
STAT1 = Hi-Z
STAT2 = Hi-Z
PG = Hi-Z
SYSTEM TEST (LDO) MODE
STANDBY MODE *
VTHERM > (VDD -100 mV)
VBAT > (VREG+100 mV)
STAT1 = LOW
STAT2 = LOW
PG = LOW
PROG > 200k
Ω
STAT1 = Hi-Z
STAT2 = Hi-Z
PG = LOW
Timer Suspended
VBAT< V
PTH
PRECONDITIONING MODE
Charge Current = IPREG
STAT1 = LOW
STAT2 = Hi-Z
PG = LOW
Timer Reset
VBAT> VPTH
TIMER FAULT
No Charge Current
TEMPERATURE FAULT
FAST CHARGE MODE
Charge Current = IREG
VBAT> V
PTH
No Charge Current
Timer Expired
VBAT< VRTH
STAT1 = Hi-Z
STAT2 = Hi-Z
PG = LOW
STAT1 = Hi-Z
STAT2 = Hi-Z
PG = LOW
STAT1 = LOW
STAT2 = Hi-Z
PG = LOW
Timer Suspended
Timer Suspended
Timer Enabled
VBAT= V
REG
CONSTANT VOLTAGE MODE
Charge Voltage = VREG
STAT1 = LOW
STAT2 = Hi-Z
PG = LOW
IBAT< ITERM
Timer Expired
CHARGE COMPLETE MODE
No Charge Current
STAT1 = Hi-Z
STAT2 = LOW
PG = LOW
FIGURE 4-1:
Flow Chart.
© 2007-2011 Microchip Technology Inc.
DS22071B-page 15
MCP73837/8
In this mode, the MCP73837/8 supplies a percentage
of the charge current (established with the value of the
resistor connected to the PROG1 pin for AC mode,
established by PROG2 level for USB mode) to the
battery. The percentage or ratio of the current is factory
set. Refer to Section 1.0 “Electrical Characteristics”
for preconditioning current options.
4.1
Undervoltage Lockout (UVLO)
An internal undervoltage lockout (UVLO) circuit
monitors the input voltage and keeps the charger in
Shutdown mode until the input supply rises above the
UVLO threshold. The UVLO circuitry has a built-in
hysteresis of 75 mV for the USB-port and 55 mV for the
AC-adapter.
When the voltage at the VBAT pin rises above the
preconditioning threshold, the MCP73837/8 enters the
constant current or fast charge mode.
In the event a battery is present when the input power
is applied, the input supply must rise 100 mV above the
battery voltage before MCP73837/8 becomes
operational.
4.5
Constant Current MODE - Fast
Charge
The UVLO circuit places the device in shutdown mode
if the input supply falls to within +100 mV of the battery
voltage.
During the constant current mode, the programmed
(AC-adapter) or selected (USB-port) charge current is
supplied to the battery or load.
The UVLO circuit is always active. At any time the input
supply is below the UVLO threshold or within +100 mV
of the voltage at the VBAT pin, the MCP73837/8 is
placed in a Shutdown mode.
For AC-adapter, the charge current is established
using a single resistor from PROG1 to VSS. The
program resistor and the charge current are calculated
using the following equation:
During any UVLO condition, the battery reverse
discharge current shall be less than 2 µA.
EQUATION 4-1:
4.2
AUTONOMOUS POWER SOURCE
SELECTION
1000V
IREG = ----------------
RPROG
The MCP73837/8 devices are designed to select the
USB-port or the AC-adapter as the power source
automatically. If the AC-adapter input is not present,
the USB-port is selected. If both inputs are available,
the AC-adapter has first priority.
where RPROG is in kilo-ohms (kΩ) and IREG is in
milliampers (mA).
When charging from
a
USB-port, the host
Note:
If the input power is switched during a
charge cycle, the power path switch-over
shall be a break-before-make connection.
As a result, the charge current can
momentarily go to zero. The charge cycle
timer shall remain continuous.
microcontroller has the option of selecting either a one
unit load or a five unit loads charge rate based on the
PROG2 input. A logic LOW selects a one unit load
charge rate, a HIGH selects a five unit loads charge
rate, and high impedance input suspends or disables
charging.
4.3
Charge Qualification
Note:
USB Specification Rev. 2.0 defines the
maximum absolute current for one unit
load is 100 mA. This value is not an aver-
age over time and shall not be exceed.
For a charge cycle to begin, all UVLO conditions must
be met and a battery or output load must be present.
A charge current programming resistor must be con-
nected from PROG1 to VSS. If the PROG1 or PROG2
pin are open or floating, the MCP73837/8 is disabled
and the battery reverse discharge current is less than
2 µA. In this manner, the PROG1 pin acts as a charge
enable and can be used as a manual shutdown.
Constant current mode is maintained until the voltage
at the VBAT pin reaches the regulation voltage, VREG.,
when constant current mode is invoked, the internal
timer is reset.
4.5.1
TIMER EXPIRED DURING
CONSTANT CURRENT - FAST
CHARGE MODE
4.4
Preconditioning
If the voltage at the VBAT pin is less than the
preconditioning threshold, the MCP73837/8 enters a
preconditioning mode. The preconditioning threshold is
factory set. Refer to Section 1.0 “Electrical
Characteristics” for preconditioning threshold
options.
If the internal timer expires before the recharge voltage
threshold is reached, a timer fault is indicated and the
charge cycle terminates. The MCP73837/8 remains in
this condition until the battery is removed, the input
battery is removed or the PROG1/2 pin is opened. If the
battery is removed or the PROG1/2 pin is opened, the
MCP73837/8 enters the Stand-by mode where it
DS22071B-page 16
© 2007-2011 Microchip Technology Inc.
MCP73837/8
remains until a battery is reinserted or the PROG1/2 pin
is reconnected. If the input power is removed, the
MCP73837/8 is in Shutdown. When the input power is
reapplied, a normal start-up sequence ensues.
4.9
Thermal Regulation
The MCP73837/8 limits the charge current based on
the die temperature. The thermal regulation optimizes
the charge cycle time while maintaining device
reliability. Figure 4-2 depicts the thermal regulation for
the MCP73837/8. Refer to Section 1.0 “Electrical
Characteristics” for thermal package resistances and
Section 6.1.1.2 “Thermal Considerations” for
calculating power dissipation.
4.6
Constant Voltage Mode
When the voltage at the VBAT pin reaches the
regulation voltage, VREG, constant voltage regulation
begins. The regulation voltage is factory set to 4.20V,
4.35V, 4.40V, or 4.5V with a tolerance of ± 0.5%.
.
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
RPROG = 1 kΩ
4.7
Charge Termination
The charge cycle is terminated when, during constant
voltage mode, the average charge current diminishes
below a percentage of the programmed charge current
or the internal timer has expired. A 1 ms filter time on
the termination comparator ensures that transient load
conditions do not result in premature charge cycle ter-
mination. The percentage or ratio of the current is fac-
tory set. The timer period is factory set and can be
disabled. Refer to Section 1.0 “Electrical Character-
istics” for charge termination current ratio and timer
period options.
25 35 45 55 65 75 85 95 105 115 125 135 145 155
Junction Temperature (°C)
FIGURE 4-2:
Thermal Regulation.
The charge current is latched off and the MCP73837/8
enters a charge complete mode.
4.10 Thermal Shutdown
The MCP73837/8 suspends charge if the die
temperature exceeds 150°C. Charging will resume
when the die temperature has cooled by
approximately 10°C. The thermal shutdown is a
secondary safety feature in the event that there is a
failure within the thermal regulation circuitry.
4.8
Automatic Recharge
The MCP73837/8 continuously monitors the voltage at
the VBAT pin in the charge complete mode. If the
voltage drops below the recharge threshold, another
charge cycle begins and current is once again supplied
to the battery or load. The recharge threshold is factory
set. Refer to Section 1.0 “Electrical Characteristics”
for recharge threshold options.
Note:
Charge termination and automatic
recharge features avoid constant charging
Li-Ion batteries to prolong the life of Li-Ion
batteries while keeping their capacity at a
healthy level.
© 2007-2011 Microchip Technology Inc.
DS22071B-page 17
MCP73837/8
at the THERM pin to factory set thresholds of 1.20V
and 0.25V, typically. Once a voltage outside the
thresholds is detected during a charge cycle, the
MCP73837/8 immediately suspends the charge cycle.
5.0
DETAILED DESCRIPTION
5.1
Analog Circuitry
The MCP73837/8 suspends charge by turning off the
pass transistor and holding the timer value. The charge
cycle resumes when the voltage at the THERM pin
returns to the normal range.
5.1.1
BATTERY MANAGEMENT INPUT
SUPPLY (VDD
)
The VDD input is the input supply to the MCP73837/8.
The MCP73837/8 can be supplied by either AC-
adapter (VAC) or USB-port (VUSB) with autonomous
source selection. The MCP73837/8 automatically
enters a Power-down mode if the voltage on the VDD
input falls to within +100 mV of the battery voltage or
below the UVLO voltage (VSTOP). This feature prevents
draining the battery pack when both the VAC and VUSB
supplies are not present.
If temperature monitoring is not required, place a
standard 10 kΩ resistor from THERM to VSS
.
5.1.5 SYSTEM TEST (LDO) MODE
The MCP73837/8 can be placed in a System Test
mode. In this mode, the MCP73837/8 operates as a
low dropout linear regulator (LDO). The output voltage
is regulated to the factory set voltage regulation option.
The available output current is limited to the pro-
grammed fast charge current. For stability, the VBAT
output must be bypassed to VSS with a minimum
capacitance of 1 µF for output currents up to 250 mA.
A minimum capacitance of 4.7 µF is required for output
currents above 250 mA.
5.1.2
AC-ADAPTER CURRENT
REGULATION SET (PROG1)
For the MCP73837/8, the charge current regulation
can be scaled by placing a programming resistor
(RPROG) from the PROG1 input to VSS. The program
resistor and the charge current are calculated using
the following equation:
The system test mode is entered by driving the THERM
input greater than (VDD - 100 mV) with no battery
connected to the output. In this mode, the MCP73837/
8 can be used to power the system without a battery
being present.
EQUATION 5-1:
1000V
IREG = ----------------
RPROG
Where:
Note 1: ITHERM is disabled during shutdown,
stand-by, and system test modes.
RPROG
IREG
=
=
kilo-ohms (kΩ)
milli-ampere (mA)
2: A pull-down current source on the
THERM input is active only in stand-by
and system test modes.
The preconditioning current and the charge
termination current are ratiometric to the fast charge
current based on the selected device options.
3: During system test mode, the PROG
input sets the available output current
limit.
5.1.3
BATTERY CHARGE CONTROL
OUTPUT (VBAT
4: System test mode shall be exited by
releasing the THERM input or cycling
input power.
)
The battery charge control output is the drain terminal
of an internal P-channel MOSFET. The MCP73837/8
provides constant current and voltage regulation to the
battery pack by controlling this MOSFET in the linear
region. The battery charge control output should be
connected to the positive terminal of the battery pack.
5.2
Digital Circuitry
5.2.1
STATUS INDICATORS AND POWER
GOOD (PG) OPTION
The charge status outputs have two different states:
Low (L), and High Impedance (Hi-Z). The charge status
outputs can be used to illuminate LEDs. Optionally, the
charge status outputs can be used as an interface to a
host microcontroller. Table 5-1 summarizes the state of
the status outputs during a charge cycle.
5.1.4
TEMPERATURE QUALIFICATION
(THERM)
The MCP73837/8 continuously monitors battery
temperature during a charge cycle by measuring the
voltage between the THERM and the VSS pins. An
internal 50 µA current source provides the bias for the
most common 10 kΩ negative-temperature coefficient
(NTC) or positive-temperature coefficient (PTC)
thermistors. The current source is controlled, avoiding
measurement sensitivity to fluctuations in the supply
voltage (VDD). The MCP73837/8 compares the voltage
DS22071B-page 18
© 2007-2011 Microchip Technology Inc.
MCP73837/8
5.2.2
USB-PORT CURRENT
5.2.4
TIMER ENABLE (TE) OPTION
REGULATION SELECT (PROG2)
The timer enable (TE) input option is used to enable or
disable the internal timer. A low signal on this pin
enables the internal timer and a high signal disables
the internal timer. The TE input can be used to disable
the timer when the charger is supplying current to
charge the battery and power the system load. The TE
input is compatible with 1.8V logic. The TE option is
available only on MCP73838.
For the MCP73837/8, driving the PROG2 input to a
logic Low selects the low charge current setting
(maximum 100 mA). Driving the PROG2 input to a logic
High selects the high charge current setting (maximum
500 mA).
The Precondition current and Termination current are
percentages of the charge current selected by the
PROG2 level. The percentage is based upon the
selected part number of the device.
5.2.5
DEVICE DISABLE (PROG1/2)
The current regulation set input pin (PROG1/2) can be
used to terminate a charge at any time during the
charge cycle, as well as to initiate a charge cycle or to
initiate a recharge cycle. Placing a programming
resistor from the PROG1/2 input to VSS enables the
device. Allowing the PROG1/2 input to float or applying
a logic-high input signal to PROG1 disables the device
and terminates a charge cycle. When disabled, the
device’s supply current is reduced to 75 µA, typically.
TABLE 5-1:
STATUS OUTPUTS
CHARGE CYCLE STATE
Shutdown
STAT1
Hi-Z
Hi-Z
L
STAT2
Hi-Z
Hi-Z
Hi-Z
Hi-Z
Hi-Z
L
PG
Hi-Z
L
Standby
Preconditioning
L
Constant Current
Constant Voltage
Charge Complete - Standby
Temperature Fault
Timer Fault
L
L
L
L
Hi-Z
Hi-Z
Hi-Z
L
L
Hi-Z
Hi-Z
L
L
L
System Test Mode
L
5.2.3
POWER GOOD (PG) OPTION
The power good (PG) option is a pseudo open-drain
output. The PG output can sink current, but not source
current. However, there is a diode path back to the
input, and as such, the output should be pulled up only
to the input. The PG output is low whenever the input
to the MCP73837 is above the UVLO threshold and
greater than the battery voltage. If the supply voltage is
above the UVLO, but below VREG(typical)+0.3V, the
MCP73837 will pulse the PG output as the device
determines if a battery is present. The PG option is
available only on MCP73837.
© 2007-2011 Microchip Technology Inc.
DS22071B-page 19
MCP73837/8
Lithium-Polymer cells Constant-current followed by
Constant-voltage. Figure 6-1 depicts a typical stand-
alone MCP73837 application circuit, while Figure 6-2
and Figure 6-3 depict the accompanying charge
profile.
6.0
APPLICATIONS
The MCP73837/8 devices are designed to operate in
conjunction with a host microcontroller or in stand-
alone applications. The MCP73837/8 devices provide
the preferred charge algorithm for Lithium-Ion and
1
2
3
10
VAC
VBAT
Thermsitor
9
COUT
Single
Li-Ion
Cell
USB Port
VUSB
THERM
C
IN1
1
ΚΩ
REGULATED
WALL CUBE
C
IN2
5
VSS
STAT1
1
1
ΚΩ
ΚΩ
4
8
7
6
STAT2
/PG
PROG2
PROG1
Hi
Low
RPROG
MCP73837
FIGURE 6-1:
MCP73837 Typical Stand-Alone Application Circuit.
6.1 Application Circuit Design
5.0
V
1.2
Due to the low efficiency of linear charging, the most
important factors are thermal design and cost, which
are a direct function of the input voltage, output current,
and thermal impedance between the battery charger
and the ambient cooling air. The worst-case situation is
when the device has transitioned from the
Preconditioning mode to the Constant Current mode. In
this situation, the battery charger has to dissipate the
maximum power. A trade-off must be made between
the charge current, cost, and thermal requirements of
the charger.
OUT
1
4.0
3.0
2.0
1.0
0.0
I
0.8
0.6
0.4
0.2
0
OUT
VDD = 5.2V
RPROG = 1 kΩ
1200 mAh Li-Ion Battery
Time (Minutes)
6.1.1
COMPONENT SELECTION
FIGURE 6-2:
Typical Charge Profile
(1200 mAh Li-Ion Battery).
Selection of the external components in Figure 6-1 is
crucial to the integrity and reliability of the charging
system. The following discussion is intended as a guide
for the component selection process.
4.5
1.2
0.9
0.6
0.3
0
V
OUT
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
6.1.1.1
Charge Current
I
OUT
The preferred fast charge current for Lithium-Ion cells
should always follow references and guidance from
battery manufacturers. For example, programming
700 mA fast charge current for a 1000 mAh Li-Ion
battery pack if its preferred fast charge rate is 0.7C.
This will result in the shortest charge cycle time without
degradation of a battery's life and performance.
VDD = 5.2V
PROG = 1 kΩ
1200 mAh Li-Ion Battery
R
0
1
2
3
4
5
6
7
8
9
10
Time (Minutes)
6.1.1.2
Thermal Considerations
FIGURE 6-3:
Thermal Regulation (1200 mAh Li-Ion Battery).
Typical Charge Profile in
The worst-case power dissipation in the battery char-
ger occurs when the input voltage is at the maximum
and the device has transitioned from the
Preconditioning mode to the Constant-current mode. In
this case, the power dissipation is:
DS22071B-page 20
© 2007-2011 Microchip Technology Inc.
MCP73837/8
Placing a programming resistor from the PROG1 input
to VSS or driving PROG2 to logic High or Low enables
the device. Allowing either the PROG1 or PROG2 input
float disables the device and terminates a charge cycle.
When disabled, the device’s supply current is reduced
to 75 µA, typically.
EQUATION 6-1:
PowerDissipation = (V
– V
) × I
PTHMIN REGMAX
DDMAX
Where:
VDDMAX
IREGMAX
VPTHMIN
=
=
=
the maximum input voltage
the maximum fast charge current
6.1.1.6
Temperature Monitoring
the minimum transition threshold
voltage
The charge temperature window can be set by placing
fixed value resistors in series-parallel with a thermistor.
The resistance values of RT1 and RT2 can be calculated
with the following equations in order to set the
temperature window of interest.
For example, power dissipation with a 5V, ±10% input
voltage source and 500 mA, ±10% fast charge current
is:
For NTC thermistors:
EXAMPLE 6-1:
EQUATION 6-2:
PowerDissipation = (5.5V – 2.7V) × 550mA = 1.54W
RT2 × RCOLD
24kΩ = RT1 + --------------------------------
R
T2 + RCOLD
This power dissipation with the battery charger in the
MSOP-10 package will cause thermal regulation to be
entered as depicted in Figure 6-3. Alternatively, the
3 mm x 3 mm DFN package could be utilized to reduce
the charge cycle times.
RT2 × RHOT
5kΩ = RT1 + ----------------------------
R
T2 + RHOT
Where:
R
=
=
=
the fixed series resistance
the fixed parallel resistance
T1
6.1.1.3
External Capacitors
R
T2
COLD
R
the thermistor resistance at the
lower temperature of interest
The MCP73837/8 is stable with or without a battery
load. In order to maintain good AC stability in the
Constant Voltage mode, a minimum capacitance of
R
=
the thermistor resistance at the
upper temperature of interest
HOT
1 µF is recommended to bypass the VBAT pin to VSS
.
This capacitance provides compensation when there is
no battery load. In addition, the battery and
interconnections appear inductive at high frequencies.
These elements are in the control feedback loop during
Constant Voltage mode. Therefore, the bypass
capacitance may be necessary to compensate for the
inductive nature of the battery pack.
For example, by utilizing a 10 kΩ at 25°C NTC
thermistor with a sensitivity index, β, of 3892, the
charge temperature range can be set to 0°C - 50°C by
placing a 1.54 kΩ resistor in series (RT1), and a
69.8 kΩ resistor in parallel (RT2) with the thermistor.
6.1.1.7
Charge Status Interface
Virtually any good quality output filter capacitor can be
used, independent of the capacitor’s minimum
Effective Series Resistance (ESR) value. The actual
value of the capacitor (and its associated ESR)
depends on the output load current. A 1 µF ceramic,
tantalum, or aluminum electrolytic capacitor at the
output is usually sufficient to ensure stability for output
currents up to 500 mA.
A status output provides information on the state of
charge. The output can be used to illuminate external
LEDs or interface to a host microcontroller. Refer to
Figure 5-1 for a summary of the state of the status
output during a charge cycle.
6.2
PCB Layout Issues
6.1.1.4
Reverse-Blocking Protection
For optimum voltage regulation, place the battery pack
as close as possible to the device’s VBAT and VSS pins,
recommended to minimize voltage drops along the
high current-carrying PCB traces.
The MCP73837/8 provides protection from a faulted or
shorted input. Without the protection, a faulted or
shorted input would discharge the battery pack through
the body diode of the internal pass transistor.
If the PCB layout is used as a heat sink, adding many
vias in the heatsink pad can help conduct more heat to
the backplane of the PCB, thus reducing the maximum
junction temperature.
6.1.1.5
Charge Inhibit
The current regulation set input pin (PROG1/2) can be
used to terminate a charge at any time during the
charge cycle, as well as to initiate a charge cycle or
initiate a recharge cycle.
© 2007-2011 Microchip Technology Inc.
DS22071B-page 21
MCP73837/8
7.0
7.1
PACKAGING INFORMATION
Package Marking Information
10-Lead DFN
Example:
Marking
Code
Marking
Code
Part Number *
Part Number *
1
2
3
4
5
10
9
1
10
9
XXXX
XYWW
NNN
BABA
0148
256
2
3
4
5
MCP73837-FCI/MF
MCP73837-FJI/MF
MCP73837-NVI/MF
MCP73838-FCI/MF
MCP73838-FJI/MF
MCP73838-NVI/MF
BABA
BABB
BABC
BACA
BACB
BACC
MCP73837T-FCI/MF
MCP73837T-FJI/MF
MCP73837T-NVI/MF
MCP73838T-FCI/MF
MCP73838T-FJI/MF
MCP73838T-NVI/MF
BABA
BABB
BABC
BACA
BACB
BACC
8
8
7
7
6
6
* Consult Factory for Alternative Device Options.
Example:
10-Lead MSOP * *
Marking
Code
Marking
Code
Part Number *
Part Number *
MCP73837-FCI/UN
MCP73837-FJI/UN
MCP73837-NVI/UN
MCP73838-FCI/UN
MCP73838-FJI/UN
MCP73838-NVI/UN
MCP73838-AMI/UN
837FCI MCP73837T-FCI/UN
837FCI
837FJI
837NVI
838FCI
838FJI
838NVI
837FCI
148256
XXXXXX
YWWNNN
837FJI
MCP73837T-FJI/UN
837NVI MCP73837T-NVI/UN
838FCI MCP73838T-FCI/UN
838FJI
MCP73838T-FJII/UN
838NVI MCP73838T-NVI/UN
838AMI MCP73838T-AMI/UN 838AMI
* Consult Factory for Alternative Device Options.
* * Consult Factory for MSOP Package Availability.
Legend: XX...X Customer-specific information
Y
Year code (last digit of calendar year)
YY
WW
NNN
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
e
3
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
*
)
3
e
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
DS22071B-page 22
© 2007-2011 Microchip Technology Inc.
MCP73837/8
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2007-2011 Microchip Technology Inc.
DS22071B-page 23
MCP73837/8
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS22071B-page 24
© 2007-2011 Microchip Technology Inc.
MCP73837/8
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2007-2011 Microchip Technology Inc.
DS22071B-page 25
MCP73837/8
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢉꢅꢊꢋꢌꢍꢇꢎꢌꢍꢏꢐꢇꢑꢒꢅꢉꢉꢇꢓꢔꢋꢉꢌꢕꢄꢇꢈꢅꢍꢖꢅꢗꢄꢇꢘꢙꢚꢛꢇꢜꢎꢑꢓꢈꢝ
ꢚꢐꢋꢄ 1ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ2ꢇꢔꢉꢅ"ꢊꢇ)ꢃꢄꢔ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢒꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ2ꢇꢔꢃꢄꢔꢅꢖꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ033)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ2ꢇꢔꢃꢄꢔ
D
N
E
E1
NOTE 1
1
2
b
e
c
A
A2
φ
L
A1
L1
4ꢄꢃ%
ꢒꢚ55ꢚꢒ*ꢘ*ꢙꢖ
ꢐꢃ&ꢉꢄ ꢃꢌꢄꢅ5ꢃ&ꢃ%
ꢒꢚ6
67ꢒ
ꢒꢕ8
6!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
6
ꢉ
ꢀꢓ
ꢓꢁ+ꢓꢅ.ꢖ/
7ꢆꢉꢊꢇꢈꢈꢅ9ꢉꢃꢔꢎ%
ꢒꢌꢈ"ꢉ"ꢅꢂꢇꢍ2ꢇꢔꢉꢅꢘꢎꢃꢍ2ꢄꢉ
ꢖ%ꢇꢄ"ꢌ$$ꢅ
7ꢆꢉꢊꢇꢈꢈꢅ<ꢃ"%ꢎ
ꢒꢌꢈ"ꢉ"ꢅꢂꢇꢍ2ꢇꢔꢉꢅ<ꢃ"%ꢎ
7ꢆꢉꢊꢇꢈꢈꢅ5ꢉꢄꢔ%ꢎ
1ꢌꢌ%ꢅ5ꢉꢄꢔ%ꢎ
ꢕ
M
ꢓꢁꢛ+
ꢓꢁꢓꢓ
M
ꢓꢁ;+
ꢀꢁꢀꢓ
ꢓꢁꢜ+
ꢓꢁꢀ+
ꢕꢏ
ꢕꢀ
*
*ꢀ
ꢐ
M
ꢗꢁꢜꢓꢅ.ꢖ/
,ꢁꢓꢓꢅ.ꢖ/
,ꢁꢓꢓꢅ.ꢖ/
ꢓꢁ=ꢓ
5
ꢓꢁꢗꢓ
ꢓꢁ;ꢓ
1ꢌꢌ%ꢑꢊꢃꢄ%
1ꢌꢌ%ꢅꢕꢄꢔꢈꢉ
5ꢀ
ꢀ
ꢓꢁꢜ+ꢅꢙ*1
M
ꢓꢝ
;ꢝ
5ꢉꢇ"ꢅꢘꢎꢃꢍ2ꢄꢉ
5ꢉꢇ"ꢅ<ꢃ"%ꢎ
ꢍ
(
ꢓꢁꢓ;
ꢓꢁꢀ+
M
M
ꢓꢁꢏ,
ꢓꢁ,,
ꢚꢐꢋꢄꢊ
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢐꢃ&ꢉꢄ ꢃꢌꢄ ꢅꢐꢅꢇꢄ"ꢅ*ꢀꢅ"ꢌꢅꢄꢌ%ꢅꢃꢄꢍꢈ!"ꢉꢅ&ꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢁꢅꢒꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢅ ꢎꢇꢈꢈꢅꢄꢌ%ꢅꢉ#ꢍꢉꢉ"ꢅꢓꢁꢀ+ꢅ&&ꢅꢑꢉꢊꢅ ꢃ"ꢉꢁ
,ꢁ ꢐꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢔꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢔꢅꢑꢉꢊꢅꢕꢖꢒ*ꢅ-ꢀꢗꢁ+ꢒꢁ
.ꢖ/0 .ꢇ ꢃꢍꢅꢐꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢘꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢙ*10 ꢙꢉ$ꢉꢊꢉꢄꢍꢉꢅꢐꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢑ!ꢊꢑꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢒꢃꢍꢊꢌꢍꢎꢃꢑ ꢘꢉꢍꢎꢄꢌꢈꢌꢔꢋ ꢐꢊꢇ)ꢃꢄꢔ /ꢓꢗꢞꢓꢏꢀ.
DS22071B-page 26
© 2007-2011 Microchip Technology Inc.
MCP73837/8
10-Lead Plastic Micro Small Outline Package (UN) [MSOP]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2007-2011 Microchip Technology Inc.
DS22071B-page 27
MCP73837/8
NOTES:
DS22071B-page 28
© 2007-2011 Microchip Technology Inc.
MCP73837/8
APPENDIX A: REVISION HISTORY
Revision B (December 2011)
The following is the list of modifications:
1. Updated the Functional Block Diagram on
page 3.
2. Added labels on the charts throughout
Section 2.0 “Typical Performance Curves”.
3. Updated text in Section 3.8 “USB-Port
Current Regulation Set (PROG2)”.
4. Updated text in Section 4.4 “Precondition-
ing”.
5. Updated text in Section 5.2.2 “USB-Port
Current Regulation SeLect (PROG2)”.
6. Added labels in Figure 6-2 and Figure 6-3.
Revision A (November 2007)
• Original Release of this Document.
© 2007-2011 Microchip Technology Inc.
DS22071B-page 29
MCP73837/8
NOTES:
DS22071B-page 30
© 2007-2011 Microchip Technology Inc.
MCP73837/8
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
Examples: * *
PART NO.
Device
XX
X/
XX
a)
b)
c)
d)
e)
f)
MCP73837-FCI/UN: 10-leadMSOPpackage
Output Temp. Package
Options*
MCP73837-FJI/UN: 10-leadMSOPpackage
MCP73837-NVI/UN: 10-leadMSOPpackage
MCP73837-FCI/MF: 10-lead DFN package
MCP73837-FJI/MF: 10-lead DFN package
MCP73837-NVI/MF: 10-lead DFN package
Device:
MCP73837: 1A Fully Integrated Charger,
PG function on pin 8
MCP73837T: 1A Fully Integrated Charger,
PG function on pin 8
a)
b)
c)
d)
e)
f)
MCP73838-FCI/UN: 10-leadMSOPpackage
MCP73838-FJI/UN: 10-leadMSOPpackage
MCP73838-NVI/UN: 10-leadMSOPpackage
MCP73838-AMI/UN: 10-leadMSOPpackage
MCP73838-FCI/MF: 10-lead DFN package
MCP73838-FJI/MF: 10-lead DFN package
MCP73838-NVI/MF: 10-lead DFN package
(Tape and Reel)
MCP73838: 1A Fully Integrated Charger,
TE function on pin 8
MCP73838T: 1A Fully Integrated Charger,
TE function on pin 8
(Tape and Reel)
g)
Output Options * *
* Refer to table below for different operational options.
* * Consult Factory for Alternative Device Options.
* * Consult Factory for Alternative Device Options
Temperature:
I
=
-40°C to +85°C
Package Type:
MF
UN
=
=
Plastic Dual Flat No Lead (DFN)
(3x3x0.9 mm Body), 10-lead
Plastic Micro Small Outline Package (MSOP***),
10-lead
* Operational Output Options
Output Options
V
I
/I
V
/V
I
/I
V
/V
Timer Period
REG
PREG REG
PTH REG
TERM REG
RTH REG
AM
BZ
FC
GP
G8
NV
YA
6S
4.20V
4.20V
4.20V
4.20V
4.20V
4.35V
4.40V
4.50V
4.20V
4.20V
10%
100%
10%
100%
10%
10%
10%
10%
10%
10%
71.5%
N/A
7.5%
7.5%
7.5%
7.5%
7.5%
7.5%
7.5%
7.5%
5.0%
20%
96.5%
96.5%
96.5%
96.5%
96.5%
96.5%
96.5%
96.5%
96.5%
94%
0 hours
0 hours
6 hours
6 hours
8 hours
6 hours
6 hours
6 hours
4 hours
4 hours
71.5%
N/A
71.5%
71.5%
71.5%
71.5%
66.5%
71.5%
B6
CN
* * Consult Factory for alternative device options
* * * Consult Factory for MSOP package availability
© 2007-2011 Microchip Technology Inc.
DS22071B-page 31
MCP73837/8
NOTES:
DS22071B-page 32
© 2007-2011 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
32
PIC logo, rfPIC and UNI/O are registered trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, chipKIT,
chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net,
dsPICworks, dsSPEAK, ECAN, ECONOMONITOR,
FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP,
Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB,
MPLINK, mTouch, Omniscient Code Generation, PICC,
PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE,
rfLAB, Select Mode, Total Endurance, TSHARC,
UniWinDriver, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2007-2011, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 978-1-61341-885-7
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2007-2011 Microchip Technology Inc.
DS22071B-page 33
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Web Address:
www.microchip.com
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Osaka
Tel: 81-66-152-7160
Fax: 81-66-152-9310
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Korea - Seoul
China - Hangzhou
Tel: 86-571-2819-3187
Fax: 86-571-2819-3189
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Los Angeles
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-330-9305
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Toronto
Mississauga, Ontario,
Canada
China - Xiamen
Tel: 905-673-0699
Fax: 905-673-6509
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
11/29/11
DS22071B-page 34
© 2007-2011 Microchip Technology Inc.
相关型号:
MCP73837T-GPI/MF
1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10, 3 X 3 MM, 0.90 MM HEIGHT, PLASTIC, DFN-10
MICROCHIP
MCP73837T-GPI/UN
Advanced Stand-Alone Li-Ion/Li-Polymer Battery Charge Management Controller with Autonomous AC Adapter or USB Port Source Selection
MICROCHIP
MCP73837T-NVI/MF
1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10, 3 X 3 MM, 0.90 MM HEIGHT, PLASTIC, DFN-10
MICROCHIP
MCP73837T-YAI/MF
Advanced Stand-Alone Li-Ion/Li-Polymer Battery Charge Management Controller with Autonomous AC Adapter or USB Port Source Selection
MICROCHIP
MCP73837T-YAI/UN
Advanced Stand-Alone Li-Ion/Li-Polymer Battery Charge Management Controller with Autonomous AC Adapter or USB Port Source Selection
MICROCHIP
MCP73837T6SIMF
Advanced Stand-Alone Li-Ion / Li-Polymer Battery Charge Management Controller with Autonomous AC-Adapter or USB-Port Source Selection
MICROCHIP
MCP73837T6SIUN
Advanced Stand-Alone Li-Ion / Li-Polymer Battery Charge Management Controller with Autonomous AC-Adapter or USB-Port Source Selection
MICROCHIP
MCP73837TAMIMF
Advanced Stand-Alone Li-Ion / Li-Polymer Battery Charge Management Controller with Autonomous AC-Adapter or USB-Port Source Selection
MICROCHIP
MCP73837TAMIUN
Advanced Stand-Alone Li-Ion / Li-Polymer Battery Charge Management Controller with Autonomous AC-Adapter or USB-Port Source Selection
MICROCHIP
MCP73837TB6IMF
Advanced Stand-Alone Li-Ion / Li-Polymer Battery Charge Management Controller with Autonomous AC-Adapter or USB-Port Source Selection
MICROCHIP
MCP73837TB6IUN
Advanced Stand-Alone Li-Ion / Li-Polymer Battery Charge Management Controller with Autonomous AC-Adapter or USB-Port Source Selection
MICROCHIP
©2020 ICPDF网 联系我们和版权申明