MIC2205-1.58YML-TR [MICROCHIP]
2A SWITCHING REGULATOR, 2200kHz SWITCHING FREQ-MAX, PDSO10;型号: | MIC2205-1.58YML-TR |
厂家: | MICROCHIP |
描述: | 2A SWITCHING REGULATOR, 2200kHz SWITCHING FREQ-MAX, PDSO10 开关 光电二极管 输出元件 |
文件: | 总16页 (文件大小:976K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MIC2205
2MHz PWM Synchronous Buck
Regulator with LDO Standby Mode
General Description
Features
The Micrel MIC2205 is a high efficiency 2MHz PWM
synchronous buck (step-down) regulator that
features a LOWQ™ LDO standby mode that draws
only 18µA of quiescent current. The MIC2205
allows an ultra-low noise, small size, and high
efficiency solution for portable power applications.
• 2.7 to 5.5V supply voltage
• Light load LOWQ™ LDO mode
18µA quiescent current
Low noise, 75µVrms
• 2MHz PWM mode
Output current to 600mA
>95% efficiency
100% maximum duty cycle
In PWM mode, the MIC2205 operates with a
constant frequency 2MHz PWM control. Under light
load conditions, such as in system sleep or standby
modes, the PWM switching operation can be
disabled to reduce switching losses. In this light
load LOWQ™ mode, the LDO maintains the output
voltage and draws only 18µA of quiescent current.
The LDO mode of operation saves battery life while
not introducing spurious noise and high ripple as
experienced with pulse skipping or bursting mode
regulators.
• Adjustable output voltage option down to 1V
Fixed output voltage options available
• Ultra-fast transient response
• Stable with 1µF ceramic output capacitor
• Fully integrated MOSFET switches
• Micropower shutdown
• Thermal shutdown and current limit protection
• Pb-free 3mm x 3mm MLF-10L package
• –40°C to +125°C junction temperature range
The MIC2205 operates from 2.7V to 5.5V input and
features internal power MOSFETs that can supply
up to 600mA output current in PWM mode. It can
operate with a maximum duty cycle of 100% for use
in low-dropout conditions.
Applications
The MIC2205 is available in the 3mm x 3mm MLF-
10L package with a junction operating range from
–40°C to +125°C.
• Cellular phones
• PDAs
• USB peripherals
Data sheets and support documentation can be
found on Micrel’s web site at www.micrel.com.
____________________________________________________________________________________________________
Typical Application
MIC2205
2.2µH
VIN
8
4
9
2
VOUT
VIN
SW
2.7V to 5.5V
AVIN
LDO
6
7
3
R1
C3
100pF
C1
1µF
EN
100k
5
FB
LOWQ
BIAS
LowQ
C4
2.2µF
R2
125k
C2
0.1µF
PGND AGND
10
1
GND
GND
Adjustable Output Buck Regulator with LOWQ™ Mode
LOWQ is a trademark of Micrel, Inc
Micrel, Inc • 2180 Fortune Drive • San Jose, Ca 95131 • USA • tel +1 (408) 944-0800 • fax +1 (408) 474-1000 • http://www.micrel.com
M9999-031105
www.micrel.com
March 2005
Micrel, Inc.
MIC2205
Ordering Information
Part Number
Output
Junction Temp. Range
Package
Lead Finish
Voltage(1)
MIC2205YML
MIC2205-1.58YML
Note:
Adj.
–40° to +125°C
–40° to +125°C
3x3 MLF-10L
3x3 MLF-10L
Pb-free
Pb-free
1.58V
1. Other Voltage options available. Contact Micrel for details.
Pin Configuration
3mm x 3mm MLF-10L (ML)
Pin Description
Pin Number
Pin Name
AGND
LDO
Pin Function
1
2
3
Analog (signal) Ground.
LDO Output (Output): Connect to VOUT for LDO mode operation.
BIAS
Internal circuit bias supply. Must be de-coupled to signal ground with a 0.1µF
capacitor and should not be loaded.
4
5
AVIN
FB
Analog Supply Voltage (Input): Supply voltage for the analog control circuitry and
LDO input power. Requires bypass capacitor to GND.
Feedback. Input to the error amplifier. For the Adjustable option, connect to the
external resistor divider network to set the output voltage. For fixed output
voltage options, connect to VOUT and an internal resistor network sets the output
voltage.
6
7
EN
Enable (Input). Logic low will shut down the device, reducing the quiescent
current to less than 5µA.
_____
LOWQ
Enable LDO Mode (Input): Logic low enables the internal LDO and disables the
PWM operation. Logic high enables the PWM mode and disables the LDO
mode.
8
9
VIN
SW
Supply Voltage (Input): Supply voltage for the internal switches and drivers.
Switch (Output): Internal power MOSFET output switches.
Power Ground.
10
EP
PGND
GND
Ground, backside pad.
M9999-031105
www.micrel.com
March 2005
2
Micrel, Inc.
MIC2205
Absolute Maximum Ratings(1)
Operating Ratings(2)
Supply Voltage (VIN) ............................................ +6V
Output Switch Voltage (VSW) ............................... +6V
Output Switch Current (ISW)................................... 2A
Logic Input Voltage (VEN,VLOWQ) .............. -0.3V to VIN
Storage Temperature (Ts)................ -60°C to +150°C
ESD Rating(3) ....................................................... 3kV
Supply Voltage (VIN)............................+2.7V to +5.5V
Logic Input Voltage (VEN,VLOWQ) .............. -0.3V to VIN
Junction Temperature (TJ).............. –40°C to +125°C
Junction Thermal Resistance
3x3 MLF-10L (θJA)................................... 60°C/W
Electrical Characteristics (4)
VIN = VEN = VLOWQ =3.6V; L = 2.2µH; COUT = 2.2µF; TA = 25°C, unless noted. Bold values indicate –40°C< TJ < +125°C
Parameter
Condition
Min
2.7
Typ
Max
5.5
Units
Supply Voltage Range
V
V
Under-Voltage Lockout
Threshold
(turn-on)
2.45
2.55
2.65
UVLO Hysteresis
100
690
mV
µA
Quiescent Current, PWM
mode
V
V
FB = 0.9 * VNOM (not switching)
LOWQ = 0V;IOUT = 0mA
900
29
5
Quiescent Current, LDO
mode
16
µA
Shutdown Current
VEN = 0V
0.01
1
µA
V
0.99
0.98
1.01
1.02
[Adjustable] Feedback
Voltage
± 1%
± 2% (over temperature)
-1
-2
+1
+2
[Fixed Output] Voltages
FB pin input current
Nominal VOUT tolerance
%
1
1
nA
A
Current Limit in PWM Mode VFB = 0.9 * VNOM
0.75
1.85
Output Voltage Line
Regulation
VOUT > 2V; VIN = VOUT+300mV to 5.5V; ILOAD= 100mA
OUT < 2V; VIN = 2.7V to 5.5V; ILOAD= 100mA
0.13
%
V
Output Voltage Load
Regulation, PWM Mode
20mA < ILOAD < 300mA
0.2
0.1
0.5
0.2
%
%
Output Voltage Load
100µA < ILOAD < 50mA
Regulation, LDO Mode
VLOWQ = 0V
Maximum Duty Cycle
100
%
VFB ≤ 0.4V
ISW = 50mA VFB = 0.7VFB_NOM (High Side Switch)
0.4
0.4
2
PWM Switch ON-
Resistance
Ω
I
SW = -50mA VFB = 1.1VFB_NOM (Low Side Switch)
Oscillator Frequency
1.8
0.5
2.2
1.3
MHz
V
LOWQ threshold voltage
0.85
LOWQ Input Current
Enable Threshold
0.1
0.85
0.1
2
1.3
2
µA
V
0.5
Enable Input Current
LDO Dropout Voltage
µA
mV
I
OUT = 50mA Note 5
110
M9999-031105
www.micrel.com
March 2005
3
Micrel, Inc.
MIC2205
Parameter
Condition
Min
60
Typ
Max
Units
Output Voltage Noise
LDO Current Limit
LOWQ = 0V; COUT = 2.2µF, 10Hz to 100kHz
LOWQ = 0V; VOUT = 0V (LDO Mode)
75
µVrms
120
160
mA
Over-Temperature
Shutdown
°C
Over-Temperature
Hysteresis
20
°C
Notes
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. Devices are ESD sensitive. Handling precautions recommended. Human body model: 1.5kΩ in series with 100pF.
4. Specification for packaged product only.
5. Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal value that is
initially measured at a 1V differential. For outputs below 2.7V, the dropout voltage is the input-to-output voltage differential with a
minimum input voltage of 2.7V.
M9999-031105
www.micrel.com
March 2005
4
Micrel, Inc.
MIC2205
Typical Characteristics – PWM Mode
M9999-031105
www.micrel.com
March 2005
5
Micrel, Inc.
MIC2205
Typical Characteristics – PWM Mode (cont.)
M9999-031105
www.micrel.com
March 2005
6
Micrel, Inc.
MIC2205
Typical Characteristics - LDO Mode
M9999-031105
www.micrel.com
March 2005
7
Micrel, Inc.
MIC2205
Typical Characteristics – LDO Mode (cont.)
M9999-031105
www.micrel.com
March 2005
8
Micrel, Inc.
MIC2205
Functional Diagram
MIC2205 Block Diagram
M9999-031105
www.micrel.com
March 2005
9
Micrel, Inc.
MIC2205
Functional Characteristics
Load Transient PWM Mode
LowQ = VIN
Time 20 s/div
Enable Transient PWM Mode
LowQ = 0V
Time 40 s/div
M9999-031105
www.micrel.com
March 2005
10
Micrel, Inc.
MIC2205
Functional Characteristics
M9999-031105
www.micrel.com
March 2005
11
Micrel, Inc.
MIC2205
Functional Description
VIN
FB
VIN provides power to the MOSFETs for the switch
mode regulator section, along with the current
limiting sensing. Due to the high switching speeds, a
1µF capacitor is recommended close to VIN and the
power ground (PGND) pin for bypassing. Please
refer to layout recommendations.
The feedback pin (FB) provides the control path to
control the output. For adjustable versions, a resistor
divider connecting the feedback to the output is used
to adjust the desired output voltage. The output
voltage is calculated as follows:
⎛
⎞
R1
R2
VOUT = VREF
×
+1
⎟
⎜
⎝
⎠
AVIN
where VREF is equal to 1.0V.
Analog VIN (AVIN) provides power to the LDO
section and the bias through an internal 6 Ohm
resistor. AVIN and VIN must be tied together.
Careful layout should be considered to ensure high
frequency switching noise caused by VIN is reduced
before reaching AVIN.
A feedforward capacitor is recommended for most
designs using the adjustable output voltage option.
To reduce battery current draw, a 100K feedback
resistor is recommended from the output to the FB
pin (R1). Also, a feedforward capacitor should be
connected between the output and feedback (across
R1). The large resistor value and the parasitic
capacitance of the FB pin can cause a high
frequency pole that can reduce the overall system
phase margin. By placing a feedforward capacitor,
these effects can be significantly reduced.
Feedforward capacitance (CFF) can be calculated as
follows:
LDO
The LDO pin is the output of the linear regulator and
should be connected to the output. In LOWQ mode
(LOWQ<1.5V), the LDO provides the output voltage.
In PWM mode (LOWQ>1.5V) the LDO pin is high
impedance.
EN
1
CFF
=
The enable pin provides a logic level control of the
output. In the off state, supply current of the device
is greatly reduced (typically <1µA). Also, in the off
state, the output drive is placed in a "tri-stated"
condition, where both the high side P-channel
Mosfet and the low-side N-channel are in an “off” or
non-conducting state. Do not drive the enable pin
above the supply voltage.
2π ×R1×160kHz
For fixed options A feed forward capacitor from the
output to the FB pin is required. Typically a 100pF
small ceramic capacitor is recommended
SW
The switch (SW) pin connects directly to the inductor
and provides the switching current nessasary to
operate in PWM mode. Due to the high speed
switching on this pin, the switch node should be
routed away from sensitive nodes.
LOWQ
The LOWQ pin provides a logic level control
between the internal PWM mode and the low noise
linear regulator mode. With LOWQ pulled low
(<0.5V), quiescent current of the device is greatly
reduced by switching to a low noise linear regulator
mode that has a typical IQ of 18µA. In linear (LDO)
mode the output can deliver 60mA of current to the
output. By placing LOWQ high (>1.5V), this
transitions the device into a constant frequency
PWM buck regulator mode. This allows the device
the ability to efficiently deliver up to 600mA of output
current at the same output voltage.
PGND
Power ground (PGND) is the ground path for the
high current PWM mode. The current loop for the
power ground should be as small as possible and
separate from the Analog ground (AGND) loop.
Refer to the layout considerations for more details.
SGND
Signal ground (SGND) is the ground path for the
biasing and control circuitry. The current loop for the
signal ground should be separate from the Power
ground (PGND) loop. Refer to the layout
considerations for more details.
BIAS
The BIAS pin supplies the power to the internal
power to the control and reference circuitry. The bias
is powered from AVIN through an internal 6Ω
resistor. A small 0.1µF capacitor is recommended
for bypassing.
M9999-031105
www.micrel.com
March 2005
12
Micrel, Inc.
MIC2205
Applications Information
Output Capacitor
The MIC2205 is a 600mA PWM power supply that
utilizes a LOWQ™ light load mode to maximize
battery efficiency in light load conditions. This is
achieved with a LOWQ control pin that when pulled
low, shuts down all the biasing and drive current for
the PWM regulator, drawing only 18µA of operating
current. This allows the output to be regulated
through the LDO output, capable of providing 60mA
of output current. This method has the advantage of
producing a clean, low current, ultra low noise output
in LOWQ™ mode. During LOWQ™ mode, the SW
node becomes high impedance, blocking current
flow. Other methods of reducing quiescent current,
such as pulse frequency modulation (PFM) or
bursting techniques, create large amplitude, low
frequency ripple voltages that can be detrimental to
system operation.
Even though the MIC2205 is optimized for a 2.2µF
output capacitor, output capacitance can be varied
from 1µF to 4.7µF. The MIC2205 utilizes type III
internal compensation and utilizes an internal high
frequency zero to compensate for the double pole
roll off of the LC filter. For this reason, larger output
capacitors can create instabilities. X5R or X7R
dielectrics are recommended for the output
capacitor. Y5V dielectrics lose most of their
capacitance over temperature and are therefore, not
recommended.
In addition to a 2.2µF, a small 10nF is recommended
close to the load for high frequency filtering. Smaller
case size capacitors are recommended due to there
lower ESR and ESL.
Inductor Selection
When more than 60mA is required, the LOWQ pin
can be forced high, causing the MIC2205 to enter
PWM mode. In this case, the LDO output makes a
"hand-off" to the PWM regulator with virtually no
variation in output voltage. The LDO output then
turns off allowing up to 600mA of current to be
efficiently supplied through the PWM output to the
load.
The MIC2205 is designed for use with a 2.2µH
inductor. Proper selection should ensure the
inductor can handle the maximum average and peak
currents required by the load. Maximum current
ratings of the inductor are generally given in two
methods; permissible DC current and saturation
current. Permissible DC current can be rated either
for a 40°C temperature rise or a 10% to 20% loss in
inductance. Ensure that the inductor selected can
handle the maximum operating current. When
saturation current is specified, make sure that there
is enough margin that the peak current will not
saturate the inductor. Peak inductor current can be
calculated as follows:
Input Capacitor
A minimum 1µF ceramic is recommended on the
VIN pin for bypassing. X5R or X7R dielectrics are
recommended for the input capacitor. Y5V
dielectrics lose most of their capacitance over
temperature and are therefore, not recommended.
⎛
⎞
⎟
⎟
⎠
VOUT
⎜
VOUT 1−
A minimum 1µF is recommended close to the VIN
and PGND pins for high frequency filtering. Smaller
case size capacitors are recommended due to their
lower ESR and ESL. Please refer to layout
recommendations for proper layout of the input
capacitor.
⎜
V
IN
⎝
IPK = IOUT
+
2× f ×L
M9999-031105
www.micrel.com
March 2005
13
Micrel, Inc.
MIC2205
Layout Recommendations
Top
Bottom
Note:
The above figures demonstrate the recommended layout for the MIC2205 adjustable option.
M9999-031105
www.micrel.com
March 2005
14
Micrel, Inc.
MIC2205
MIC2205
2.2µH
VIN
8
4
9
2
VOUT
VIN
SW
2.7V to 5.5V
AVIN
LDO
6
7
3
R1
C3
100pF
C1
1µF
EN
100k
5
FB
LOWQ
BIAS
LowQ
C4
2.2µF
R2
125k
C2
0.1µF
PGND AGND
10
1
GND
GND
Adjustable Output
MIC2205
2.2µH
VIN
8
4
9
2
VOUT
VIN
SW
2.7V to 5.5V
AVIN
LDO
6
7
3
C3
100pF
C1
1µF
EN
5
FB
LOWQ
BIAS
LowQ
C4
2.2µF
C2
0.1µF
PGND AGND
10
1
GND
GND
Fixed Output
Item
Part Number
Description
Manufacturer
Qty
C1
06036D105MAT2
GRM185R60J105KE21D
1µF Ceramic Capacitor X5R, 6.3V 0603
1µF Ceramic Capacitor X5R, 6.3V 0603
AVX
1
Murata(4)
C4
06036D225MAT2
GRM188R61A225KE34
2.2µF Ceramic Capacitor X5R, 10V 0603
2.2µF Ceramic Capacitor X5R, 10V 0603
AVX
1
1
1
Murata(4)
C3
C2
VJ0402A101KXAA
100pF Ceramic Capacitor
Vishay(3)
0201ZD103MAT2
GRM033R10J103KA01D
10nF Ceramic Capacitor 6.3V 0201
10nF Ceramic Capacitor 6.3V 0201
AVX
Murata(4)
L1
LQH32CN2R2M53K
CDRH2D14-2R2
R1(1) CRCW04021002F
2.2µH Inductor 97mΩ 3.2mmx2.5mmx1.55mm
2.2µH Inductor 94mΩ 3.2mmx3.2mmx1.55mm
Murata(4)
1
1
Sumida(2)
100kΩ 1% 0402
Vishay Dale(3)
R2(1) CRCW04026652F
CRCW04021243F
66.5 kΩ 1% 0402 For 2.5VOUT
124 kΩ 1% 0402 For 1.8 VOUT
200 kΩ 1% 0402 For 1.5 VOUT
402 kΩ 1% 0402 For 1.2 VOUT
Vishay Dale(3)
Vishay Dale(3)
Vishay Dale(3)
Vishay Dale(3)
Vishay Dale(3)
CRCW04022003F
CRCW04024023F
Open
For 1.0 VOUT
U1
MIC2205BML
2MHz Synchronous Buck Regulator with LOWQTM Mode Micrel, Inc.(5)
1
Notes:
1. For adjustable version only.
2. Sumida Tel: 408-982-9660
3. Murata Tel: 949-916-4000
4. Vishay Tel: 402-644-4218
5. Micrel, Inc. Tel: 408-944-0800
M9999-031105
www.micrel.com
March 2005
15
Micrel, Inc.
MIC2205
Package Information
10-Lead MLF™ (ML)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel
for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a
product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended
for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a
significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a
Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale.
© 2004 Micrel, Incorporated.
M9999-031105
www.micrel.com
March 2005
16
相关型号:
MIC2205-1.58YMLTR
2A SWITCHING REGULATOR, 2200kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, LEAD FREE, MLF-10
MICREL
MIC2205-1.5YMLTR
2A SWITCHING REGULATOR, 2200kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, LEAD FREE, MLF-10
MICREL
MIC2205-1.85YMLTR
2A SWITCHING REGULATOR, 2200kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, LEAD FREE, MLF-10
MICREL
MIC2205YMLTR
2 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, LEAD FREE, MLF-10
ROCHESTER
©2020 ICPDF网 联系我们和版权申明