MIC23250-GFHYMTTR [MICROCHIP]
1A SWITCHING REGULATOR, 4000kHz SWITCHING FREQ-MAX, PDSO10, 2 X 2 MM, GREEN, MLF-10;
| 型号： | MIC23250-GFHYMTTR |
| 厂家： | 
MICROCHIP |
| 描述： | 1A SWITCHING REGULATOR, 4000kHz SWITCHING FREQ-MAX, PDSO10, 2 X 2 MM, GREEN, MLF-10 开关 光电二极管 |
| 文件： | 总20页 (文件大小：988K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MIC23250
4MHz Dual 400mA Synchronous Buck
Regulator with HyperLight Load™
General Description
Features
The MIC23250 is a high efficiency 4MHz dual 400mA
synchronous buck regulator with HyperLight Load™ mode.
HyperLight Load™ provides very high efficiency at light
loads and ultra-fast transient response which is perfectly
suited for supplying processor core voltages. An additional
benefit of this proprietary architecture is very low output
ripple voltage throughout the entire load range with the use
of small output capacitors. The fixed output MIC23250 has
a tiny 2mm x 2mm Thin MLF® package that saves
precious board space by requiring only 6 additional
external components to drive both outputs up to 400mA
each.
• Input voltage: 2.7V to 5.5V
• Dual output current 400mA/400mA
• Up to 94% peak efficiency and 85% efficiency at 1mA
• 33µA dual quiescent current
• 1µH inductor with a 4.7µF capacitor
• 4MHz in PWM operation
• Ultra fast transient response
HyperLight Load™
• Low voltage output ripple
• 20mVpp in HyperLight Load™ mode
• 3mV output voltage ripple in full PWM mode
• 0.01µA shutdown current
• Fixed output:10-pin 2mm x 2mm Thin MLF®
• Adjustable output:12-pin 2.5mm x 2.5mm Thin MLF®
• –40°C to +125°C junction temperature range
The device is designed for use with a 1µH inductor and a
4.7µF output capacitor that enables a sub-1mm height.
The MIC23250 has a very low quiescent current of 33µA
with both outputs enabled and can achieve over 85%
efficiency at 1mA. At higher loads the MIC23250 provides a
constant switching frequency around 4MHz while providing
peak efficiencies up to 94%.
Applications
• Mobile handsets
• Portable media players
• Portable navigation devices (GPS)
• WiFi/WiMax/WiBro modules
• Digital cameras
The MIC23250 fixed output voltage option is available in a
10-pin 2mm x 2mm Thin MLF®. The adjustable output
options is available in a 12-pin 2.5mm x 2.5mm Thin MLF®.
The MIC23250 is designed to operate over the junction
operating range from –40°C to +125°C.
• Wireless LAN cards
• USB Powered Devices
Data sheets and support documentation can be found on
Micrel’s web site at: www.micrel.com.
____________________________________________________________________________________________________________
Typical Application
Efficiency V
= 1.8V
OUT
100
90
80
70
60
50
40
30
20
10
0
VIN = 3.0V
VIN = 2.7V
VIN = 4.2V
VIN = 3.6V
L = 1µH
= 4.7µF
C
OUT
11
0
100
1000
OUTPUT CURRENT (mA)
HyperLight Load is a trademark of Micrel, Inc.
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
M9999-061110-E
June 2010
Micrel, Inc.
MIC23250
Ordering Information
Part Number
Marking
Code
Nominal
Output
Nominal
Output
Junction
Temp. Range
Package
Lead
Finish
Voltage 1
Voltage 2
MIC23250-3BYMT
MIC23250-C4YMT
MIC23250-W4YMT
MIC23250-G4YMT
MIC23250-S4YMT
MIC23250-GFHYMT
MIC23250-SKYMT
MIC23250-AAYMT
Notes:
WV3
WV2
WV4
WV5
1WV
WV1
5WV
4WV
0.9V
1.2V
1.2V
1.2V
1.2V
1.575V
2.6V
ADJ
1.1V
1.0V
1.6V
1.8V
3.3V
1.8V
3.3V
ADJ
–40° to +125°C
–40° to +125°C
–40° to +125°C
–40° to +125°C
–40° to +125°C
–40° to +125°C
–40° to +125°C
–40° to +125°C
10-Pin 2mm x 2mm Thin MLF®
10-Pin 2mm x 2mm Thin MLF®
10-Pin 2mm x 2mm Thin MLF®
10-Pin 2mm x 2mm Thin MLF®
10-Pin 2mm x 2mm Thin MLF®
10-Pin 2mm x 2mm Thin MLF®
10-Pin 2mm x 2mm Thin MLF®
12-Pin 2.5mm x 2.5mm Thin MLF®
Pb-Free
Pb-Free
Pb-Free
Pb-Free
Pb-Free
Pb-Free
Pb-Free
Pb-Free
1) Additional voltage options available (0.8V to 3.3V). Contact Micrel for details.
2) Thin MLF® is GREEN RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free.
M9999-061110-E
June 2010
2
Micrel, Inc.
MIC23250
Pin Configuration
SNS1
EN1
1
2
3
4
5
10 SNS2
FB1
SNS1
EN1
1
2
3
4
5
6
12 FB2
11 SNS2
10 EN2
9
8
7
6
EN2
AVIN
SW2
VIN
AGND
SW1
AGND
SW1
9
8
7
AVIN
SW2
VIN
PGND
PGND
10-Pin 2mm x 2mm Thin MLF® (MT)
Fixed Output
12-Pin 2.5mmx2.5mm Thin MLF® (MT)
Adjustable Output
(Top View)
(Top View)
Pin Description
Pin Number
(Fixed)
Pin Number
(Adjustable)
Pin Name
FB1
Pin Function
–
1
2
1
2
3
Feedback VOUT1 (Input): Connect resistor divider at this node to set output
voltage. Resistors should be selected based on a nominal VFB of 0.72V.
SNS1
EN1
Sense 1 (Input): Error amplifier input. Connect to feedback resistor network
to set output 1 voltage.
Enable 1 (Input): Logic low will shut down output 1. Logic high powers up
output 1. Do not leave unconnected.
3
4
5
6
7
8
9
4
5
AGND
SW1
PGND
VIN
Analog Ground. Must be connected externally to PGND.
Switch Node 1 (Output): Internal power MOSFET output.
Power Ground.
6
7
Supply Voltage (Power Input): Requires close bypass capacitor to PGND.
Switch Node 2 (Output): Internal power MOSFET output.
Supply Voltage (Power Input): Analog control circuitry. Connect to VIN.
8
SW2
AVIN
EN2
9
10
Enable 2 (Input): Logic low will shut down output 2. Logic high powers up
output 2. Do not leave unconnected.
10
–
11
12
SNS2
FB2
Sense 2 (Input): Error amplifier input. Connect to feedback resistor network
to set output 2 voltage.
Feedback VOUT2 (Input): Connect resistor divider at this node to set output
voltage. Resistors should be selected based on a nominal VFB of 0.72V.
M9999-061110-E
June 2010
3
Micrel, Inc.
MIC23250
Absolute Maximum Ratings(1)
Operating Ratings(2)
Supply Voltage (VIN).........................................................6V
Output Switch Voltage (VSW)............................................6V
Logic Input Voltage (VEN1, VEN2)........................–0.3V to VIN
Storage Temperature Range (Ts)..............–65°C to +150°C
ESD Rating(3)..................................................................2kV
Supply Voltage (VIN)......................................... 2.7V to 5.5V
Logic Input Voltage (VEN1, VEN2)............................. 0V to VIN
Junction Temperature (TJ) ..................–40°C ≤ TJ ≤ +125°C
Thermal Resistance
2mm x 2mm Thin MLF-10 (θJA) .........................70°C/W
2.5mm x 2.5mm Thin MLF-12 (θJA) ...................65°C/W
Electrical Characteristics(4)
TA = 25°C with VIN = VEN1 = VEN2 = 3.6V; L = 1µH; COUT = 4.7µF; IOUT = 20mA; only one channel power is enabled, unless
otherwise specified. Bold values indicate –40°C< TJ < +125°C.
Parameter
Condition
Min
Typ
2.55
60
Max
Units
V
Under-Voltage Lockout Threshold
UVLO Hysteresis
(turn-on)
2.45
2.65
mV
Quiescent Current
VOUT1, 2 (both Enabled), IOUT1, 2 = 0mA , VSNS1,2 >1.2 * VOUT1, 2
Nominal
33
50
µA
Shutdown Current
VEN1, 2 = 0V; VIN = 5.5V
0.01
4
µA
%
Output Voltage Accuracy
VIN = 3.6V if VOUTNOM < 2.5V, ILOAD = 20mA
VIN = 4.5V if VOUTNOM ≥ 2.5V, ILOAD = 20mA
–2.5
–2.5
+2.5
+2.5
%
Feedback Voltage (Adj only)
Current Limit in PWM Mode
Output Voltage Line Regulation
0.720
0.65
0.4
V
SNS = 0.9*VOUT NOM
0.410
1
A
VIN = 3.6V to 5.5V if VOUTNOM < 2.5V, ILOAD = 20mA
VIN = 4.5V to 5.5V if VOUTNOM ≥ 2.5V, ILOAD = 20mA
20mA < ILOAD < 400mA, VIN = 3.6V if VOUTNOM < 2.5V
%/V
%/V
%
0.4
Output Voltage Load Regulation
PWM Switch ON-Resistance
0.5
20mA < ILOAD < 400mA, VIN = 5.0V if VOUTNOM ≥ 2.5V
ISW = 100mA PMOS
ISW = -100mA NMOS
0.5
%
0.6
0.8
Ω
Ω
Frequency
ILOAD = 120mA
4
MHz
µs
Soft Start Time
VOUT = 90%
260
0.8
0.1
160
Enable Threshold
Enable Input Current
Over-temperature Shutdown
0.5
1.2
2
V
µA
°C
Over-temperature Shutdown
Hysteresis
40
°C
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. Devices are ESD sensitive. Handling precautions recommended. Human body model: 1.5kΩ in series with 100pF.
4. Specification for packaged product only.
M9999-061110-E
June 2010
4
Micrel, Inc.
MIC23250
Typical Characteristics
Quiescent Current
vs. Input Voltage
Switching Frequency
vs. Output Current
Switching Frequency
vs. Output Current
50
10
10
L = 4.7µH
45
40
35
30
25
20
15
4MHz
4MHz
V
= 3.0V
IN
1
0.1
1
0.1
L = 1µH
L = 2.2µH
V
= 4.2V
IN
V
= 1.8V
V
V
= 3.6V
OUT
IN
10
L = 1µH
= 1.8V
L = 1µH
= 4.7µF
OUT
5
0
C
= 4.7µF
C
OUT
= 4.7µF
C
OUT
OUT
V
= 3.6V
0
IN
0.01
0.01
11
0
100
1000
2.7 3.2 3.7 4.2 4.7 5.2 5.7
INPUT VOLTAGE (V)
11
100
1000
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
Frequency
Output Voltage
Output Voltage
vs. Temperature
vs. Output Current
vs. Input Voltage
5.0
1.90
1.88
1.86
1.84
1.82
1.80
1.78
1.76
1.74
1.72
1.70
1.90
1.88
1.86
1.84
1.82
1.80
1.78
1.76
1.74
1.72
1.70
L = 1µH
= 4.7µF
C
OUT
4.5
4.0
3.5
3.0
Load = 1mA
Load = 10mA
VIN = 3.0V
Load = 150mA
Load = 300mA
VIN = 4.2V
VIN = 3.6V
Load = 50mA
L = 1µH
= 4.7µF
Load = 400mA
C
OUT
Load = 120mA
11
0
100
1000
2.7 3.2 3.7 4.2 4.7 5.2 5.7
INPUT VOLTAGE (V)
20 40 60 80
TEMPERATURE (°C)
OUTPUT CURRENT (mA)
Output Voltage
vs. Temperature
Enable Threshold
vs. Temperature
Enable Threshold
vs. Input Voltage
1.9
1.8
1.7
1.6
1.5
1.2
1.0
0.8
0.6
0.4
0.2
0
1.000
0.975
0.950
0.925
0.900
0.875
0.850
0.825
0.800
VIN = 3.6V
VIN = 2.7V
VOUT2 = 1.8V
VIN = 5.5V
Enable ON
L = 1µH
Enable OFF
C
= 4.7µF
OUT
Load = 120mA
VOUT1 = 1.575V
V
V
= 3.6V
IN
L = 1µH
= 4.7µF
= 1.8V
OUT
C
Load = 150mA
OUT
2.7 3.2 3.7 4.2 4.7 5.2 5.7
INPUT VOLTAGE (V)
20 40 60 80
TEMPERATURE (°C)
20 40 60 80
TEMPERATURE (°C)
Current Limit
Efficiency V
= 1.2V
OUT
Efficiency V
= 1.575V
OUT
vs. Input Voltage
700
650
600
550
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
VIN = 3.0V
VIN = 3.0V
VIN = 2.7V
VIN = 4.2V
VIN = 2.7V
VIN = 4.2V
VIN = 3.6V
VIN = 3.6V
L = 1µH
L = 1µH
= 4.7µF
L = 1µH
= 4.7µF
C
= 4.7µF
OUT
C
OUT
C
OUT
11
0
100
1000
2.7 3.2 3.7 4.2 4.7 5.2 5.7
INPUT VOLTAGE (V)
11
0
100
1000
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
M9999-061110-E
June 2010
5
Micrel, Inc.
MIC23250
Typical Characteristics (Continued)
Efficiency V
= 1.8V
Efficiency V
= 2.5V
OUT
Efficiency V
= 3.3V
OUT
OUT
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
VIN = 2.7V
VIN = 3.0V
VIN = 4.2V
VIN = 2.7V
VIN = 4.2V
VIN = 3.6V
VIN = 3.0V
VIN = 5.5V
VIN = 5.0V
VIN = 3.6V
VIN = 4.2V
L = 1µH
= 4.7µF
L = 1µH
= 4.7µF
L = 1µH
C = 4.7µF
OUT
C
OUT
C
OUT
11
0
100
1000
11
0
100
1000
11
0
100
1000
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
Efficiency V
= 1.8V
Dual Output Efficiency
OUT
With Various Inductors
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
VIN = 3.3V
L = 1.5µH
L = 1.0µH
VIN = 4.2V
VIN = 3.6V
L = 0.47µH
V
V
= 1.575V
= 1.8V
Load1 = Load2
L1 = L2 = 1µH
OUT1
OUT2
V
= 3.6V
IN
C
= C
= 4.7µF
100
C
= 4.7µF
OUT1
OUT2
OUT
11
0
1000
11
0
100
1000
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
M9999-061110-E
June 2010
6
Micrel, Inc.
MIC23250
Functional Characteristics
M9999-061110-E
June 2010
7
Micrel, Inc.
MIC23250
Functional Characteristics (Continued)
M9999-061110-E
June 2010
8
Micrel, Inc.
MIC23250
Functional Characteristics (Continued)
M9999-061110-E
June 2010
9
Micrel, Inc.
MIC23250
Functional Diagram
MIC23250 Simplified Fixed Output Block Diagram
VIN
EN1
SW1
AVIN
EN2
ENABLE
LOGIC
ENABLE
LOGIC
GATE
DRIVES
GATE
DRIVES
SW2
CONTROL
LOGIC
CONTROL
LOGIC
T
ON TIMER &
T
ON TIMER &
Zero X
Zero X
SOFT START
SOFT START
ISENSE
ISENSE
Current Limit
Current Limit
UVLO
REF1
UVLO
REF2
+
+
-
ERROR
COMPARATOR
ERROR
COMPARATOR
-
FB1
FB2
SNS1
SNS2
AGND
PGND
MIC23250 Simplified Adjustable Output Block Diagram
M9999-061110-E
June 2010
10
Micrel, Inc.
MIC23250
Functional Description
VIN
SNS1/SNS2
The VIN provides power to the internal MOSFETs for the
switch mode regulator along with the current limit sensing.
The VIN operating range is 2.7V to 5.5V so an input
capacitor with a minimum of 6.3V voltage rating is
recommended. Due to the high switching speed, a
minimum of 2.2µF bypass capacitor placed close to VIN
and the power ground (PGND) pin is required. Based upon
size, performance and cost, a TDK C1608X5R0J475K,
size 0603, 4.7µF ceramic capacitor is highly recommended
The SNS pin (SNS1 or SNS2) is connected to the output
of the device to provide feedback to the control circuitry. A
minimum of 2.2µF bypass capacitor should be connected
in shunt with each output. Based upon size, performance
and cost, a TDK C1608X5R0J475K, size 0603, 4.7µF
ceramic capacitor is highly recommended for most
applications. In order to reduce parasitic inductance, it is
good practice to place the output bypass capacitor as
close to the inductor as possible. The SNS connection
should be placed close to the output bypass capacitor.
Refer to the layout recommendations for more details.
for
most
applications.
Refer
to
the
layout
recommendations for details.
AVIN
PGND
The analog VIN (AVIN) provides power to the analog
supply circuitry. AVIN and VIN must be tied together.
Careful layout should be considered to ensure high
frequency switching noise caused by VIN is reduced
before reaching AVIN. A 0.01µF bypass capacitor placed
as close to AVIN as possible is recommended. See layout
recommendations for details.
The power ground (PGND) is the ground path for the high
current in PWM mode. The current loop for the power
ground should be as small as possible and separate from
the Analog ground (AGND) loop. Refer to the layout
recommendations for more details.
AGND
The signal ground (AGND) is the ground path for the
biasing and control circuitry. The current loop for the signal
ground should be separate from the Power ground
(PGND) loop. Refer to the layout recommendations for
more details.
EN1/EN2
The enable pins (EN1 and EN2) control the on and off
states of outputs 1 and 2, respectively. A logic high signal
on the enable pin activates the output voltage of the
device. A logic low signal on each enable pin deactivates
the output. MIC23250 features built-in soft-start circuitry
that reduces in-rush current and prevents the output
voltage from overshooting at start up.
FB1/FB2 (Adjustable Output Only)
The feedback pins (FB1/FB2) are two extra pins that can
only be found on the MIC23250-AAYMT devices. It allows
the regulated output voltage to be set by applying an
external resistor network. The internal reference voltage is
0.72V and the recommended value of RBOTTOM is within
10% of 442kΩ. The RTOP resistor is the resistor from the
FB pin to the output of the device and RBOTTOM is the
resistor from the FB pin to ground. The output voltage is
calculated from the equation below. See Compensation
under the Applications Information section for
recommended feedback component values.
SW1/SW2
The switching pin (SW1 or SW2) connects directly to one
end of the inductor (L1 or L2) and provides the current
path during switching cycles. The other end of the inductor
is connected to the load and SNS pin. Due to the high
speed switching on this pin, the switch node should be
routed away from sensitive nodes.
⎛
⎜
⎜
⎝
⎞
RTOP
⎟
+ 1
VOUT = 0.72V
⎟
RBOTTOM
⎠
M9999-061110-E
June 2010
11
Micrel, Inc.
MIC23250
Applications Information
The MIC23250 is designed for high performance with a
small solution size. With a dual 400mA output inside a tiny
2mm x 2mm Thin MLF® package and requiring only six
external components, the MIC23250 meets today’s
miniature portable electronic device needs. While small
solution size is one of its advantages, the MIC23250 is big
in performance. Using the HyperLight Load™ switching
scheme, the MIC23250 is able to maintain high efficiency
throughout the entire load range while providing ultra-fast
load transient response. Even with all the given benefits,
the MIC23250 can be as easy to use as linear regulators.
The following sections provide an over view of
implementing MIC23250 into related applications
Maximum current ratings of the inductor are generally
given in two methods; permissible DC current and
saturation current. Permissible DC current can be rated
either for a 40°C temperature rise or a 10% to 20% loss in
inductance. Ensure the inductor selected can handle the
maximum operating current. When saturation current is
specified, make sure that there is enough margin so that
the peak current of the inductor does not cause it to
saturate. Peak current can be calculated as follows:
⎡
⎤
⎥
⎦
1−V
/VIN
⎛
⎞
OUT
IPEAK = I
+VOUT
⎜
⎜
⎟
⎟
⎢
OUT
2× f × L
⎝
⎠
⎣
As shown by the previous calculation, the peak inductor
current is inversely proportional to the switching frequency
and the inductance; the lower the switching frequency or
the inductance the higher the peak current. As input
voltage increases the peak current also increases.
Input Capacitor
A minimum of 2.2µF ceramic capacitor should be placed
close to the VIN pin and PGND pin for bypassing. A TDK
C1608X5R0J475K, size 0603, 4.7µF ceramic capacitor is
recommended based upon performance, size and cost. A
X5R or X7R temperature rating is recommended for the
input capacitor. Y5V temperature rating capacitors, aside
from losing most of their capacitance over temperature,
can also become resistive at high frequencies. This
reduces their ability to filter out high frequency noise.
The size of the inductor depends on the requirements of
the application. Refer to the Application Circuit and Bill of
Material for details.
DC resistance (DCR) is also important. While DCR is
inversely proportional to size, DCR can represent a
significant efficiency loss. Refer to the Efficiency
Considerations.
Output Capacitor
Compensation
The MIC23250 was designed for use with a 2.2µF or
greater ceramic output capacitor. Increasing the output
capacitance will lower output ripple and improve load
transient response but could increase solution size or cost.
A low equivalent series resistance (ESR) ceramic output
capacitor such as the TDK C1608X5R0J475K, size 0603,
4.7µF ceramic capacitor is recommended based upon
performance, size and cost. Either the X7R or X5R
temperature rating capacitors are recommended. The Y5V
and Z5U temperature rating capacitors, aside from the
undesirable effect of their wide variation in capacitance
over temperature, become resistive at high frequencies.
The MIC23250 is designed to be stable with a 0.47µH to
4.7µH inductor with a minimum of 2.2µF ceramic (X5R)
output capacitor. For the adjustable MIC23250, the total
feedback resistance should be kept around 1Mꢀ to reduce
current loss down the feedback resistor network. This
helps to improve efficiency. A feed-forward capacitor
(CFF) of 120pF must be used in conjunction with the
external feedback resistors to reduce the effects of
parasitic capacitance that is inherent of most circuit board
layouts. Figure 1 and Table 1 shows the recommended
feedback resistor values along with the recommended
feed-forward capacitor values for the MIC23250 adjustable
device.
Inductor Selection
Inductor selection will be determined by the following (not
necessarily in the order of importance);
RTOP
CFF
•
•
•
•
Inductance
Rated current value
Size requirements
DC resistance (DCR)
RBOTTOM
The MIC23250 was designed for use with an inductance
range from 0.47µH to 4.7µH. Typically, a 1µH inductor is
recommended for a balance of transient response,
efficiency and output ripple. For faster transient response a
0.47µH inductor may be used. For lower output ripple, a
4.7µH is recommended.
Figure 1. Feedback Resistor Network
M9999-061110-E
June 2010
12
Micrel, Inc.
MIC23250
There are two types of losses in switching converters; DC
losses and switching losses. DC losses are simply the
power dissipation of I2R. Power is dissipated in the high
side switch during the on cycle. Power loss is equal to the
high side MOSFET RDSON multiplied by the Switch Current
squared. During the off cycle, the low side N-channel
MOSFET conducts, also dissipating power. Device
operating current also reduces efficiency. The product of
the quiescent (operating) current and the supply voltage is
another DC loss. The current required driving the gates on
and off at a constant 4MHz frequency and the switching
transitions make up the switching losses.
VOUT (V)
0.8
0.9
1
RTOP (kΩ) RBOTTOM (kΩ) CFF (pF)
49
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
442
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
111
172
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
233
295
356
417
479
540
Efficiency V
= 1.8V
OUT
602
100
80
60
40
20
0
V
= 2.7V
IN
663
V
= 3.6V
724
IN
786
V
= 3.3V
IN
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
847
909
970
V
= 1.8V
OUT
L = 1µH
1031
1093
1154
1216
1277
1338
1400
1461
1522
1584
0.1
11
0
100
1000
LOAD (mA)
The Figure above shows an efficiency curve. From no load
to 100mA, efficiency losses are dominated by quiescent
current losses, gate drive and transition losses. By using
the HyperLight Load™ mode the MIC23250 is able to
maintain high efficiency at low output currents.
Over 100mA, efficiency loss is dominated by MOSFET
RDSON and inductor losses. Higher input supply voltages
will increase the Gate-to-Source threshold on the internal
MOSFETs, thereby reducing the internal RDSON. This
improves efficiency by reducing DC losses in the device.
All but the inductor losses are inherent to the device. In
which case, inductor selection becomes increasingly
critical in efficiency calculations. As the inductors are
reduced in size, the DC resistance (DCR) can become
quite significant. The DCR losses can be calculated as
follows:
3.1
3.2
3.3
Table 1. Recommended Feedback Component Values
Efficiency Considerations
Efficiency is defined as the amount of useful output power,
divided by the amount of power supplied.
DCR Loss = IOUT2 × DCR
From that, the loss in efficiency due to inductor resistance
can be calculated as follows:
⎛
⎞
VOUT × IOUT
VIN × IIN
⎜
⎜
⎟
⎟
Efficiency % =
×100
⎝
⎠
⎡
⎤
⎥
⎦
⎛
⎞
VOUT × IOUT
VOUT × IOUT + L _ PD
Maintaining high efficiency serves two purposes. It
reduces power dissipation in the power supply, reducing
the need for heat sinks and thermal design considerations
and it reduces consumption of current for battery powered
applications. Reduced current draw from a battery
increases the devices operating time and is critical in hand
held devices.
⎜
⎜
⎟
⎟
Efficiency Loss = 1−
×100
⎢
⎝
⎠
⎣
Efficiency loss due to DCR is minimal at light loads and
gains significance as the load is increased. Inductor
selection becomes a trade-off between efficiency and size
in this case.
M9999-061110-E
June 2010
13
Micrel, Inc.
MIC23250
HyperLight Load Mode™
As shown in the previous equation, the load at which
MIC23250 transitions from HyperLight Load™ mode to
PWM mode is a function of the input voltage (VIN), output
voltage (VOUT), duty cycle (D), inductance (L) and
frequency (f). This is illustrated in the graph below. Since
the inductance range of MIC23250 is from 0.47µH to
4.7µH, the device may then be tailored to enter HyperLight
Load™ mode or PWM mode at a specific load current by
selecting the appropriate inductance. For example, in the
graph below, when the inductance is 4.7µH the MIC23250
will transition into PWM mode at a load of approximately
5mA. Under the same condition, when the inductance is
1µH, the MIC23250 will transition into PWM mode at
approximately 70mA.
The MIC23250 uses a minimum on and off time
proprietary control loop (patented by Micrel). When the
output voltage falls below the regulation threshold, the
error comparator begins a switching cycle that turns the
PMOS on and keeps it on for the duration of the minimum-
on-time. This increases the output voltage. If the output
voltage is over the regulation threshold, then the error
comparator turns the PMOS off for a minimum-off-time
until the output drops below the threshold. The NMOS acts
as an ideal rectifier that conducts when the PMOS is off.
Using a NMOS switch instead of a diode allows for lower
voltage drop across the switching device when it is on. The
asynchronous switching combination between the PMOS
and the NMOS allows the control loop to work in
discontinuous mode for light load operations. In
discontinuous mode, the MIC23250 works in pulse
frequency modulation (PFM) to regulate the output. As the
output current increases, the off-time decreases, thus
providing more energy to the output. This switching
scheme improves the efficiency of MIC23250 during light
load currents by only switching when it is needed. As the
load current increases, the MIC23250 goes into
continuous conduction mode (CCM) and switches at a
frequency centered at 4MHz. The equation to calculate the
load when the MIC23250 goes into continuous conduction
mode may be approximated by the following formula:
Switching Frequency
vs. Output Current
10
L = 4.7µH
4MHz
1
L = 1µH
L = 2.2µH
0.1
V
V
= 3.6V
IN
= 1.8V
OUT
C
OUT
= 4.7µF
0.01
11
0
100
1000
OUTPUT CURRENT (mA)
(
V
−VOUT
2L × f
)
× D
⎛
⎞
IN
ILOAD > ⎜
⎟
⎟
⎜
⎝
⎠
M9999-061110-E
June 2010
14
Micrel, Inc.
MIC23250
MIC23250 Typical Application Circuit (Fixed Output)
Bill of Materials
Item
Part Number
Manufacturer
TDK(1)
Description
Qty
C1, C2, C3
C4
C1608X5R0J475K
VJ0603Y103KXXAT
CRCW06031002FKEA
LQM21PN1R0MC0D
LQH32CN1R0M33
LQM31PN1R0M00
GLF251812T1R0M
LQM31PNR47M00
MIPF2520D1R5
4.7µF Ceramic Capacitor, 6.3V, X5R, Size 0603
0.01µF Ceramic Capacitor, 25V, X7R, Size 0603
10kꢀ, 1%, 1/16W, Size 0603
3
1
Vishay(2)
Vishay(2)
Murata(3)
Murata(3)
Murata(3)
TDK(1)
Murata(3)
FDK(4)
Coilcraft(5)
R1, R2
Optional
1µH, 0.8A, 190mꢀ, L2mm x W1.25mm x H0.5mm
1µH, 1A, 60mꢀ, L3.2mm x W2.5mm x H2.0mm
1µH, 1.2A, 120mꢀ, L3.2mm x W1.6mm x H0.95mm
1µH, 0.8A, 100mꢀ, L2.5mm x W1.8mm x H1.35mm
0.47µH, 1.4A, 80mꢀ, L3.2mm x W1.6mm x H0.85mm
1.5µH, 1.5A, 70mꢀ, L2.5mm x W2mm x H1.0mm
1.0µH, 1.0A, 86mꢀ, L2.0mm x W1.8mm x H1.0mm
L1, L2
2
EPL2010-102
4MHz Dual 400mA Fixed Output Buck Regulator
with HyperLight Load™ Mode
U1
MIC23250-xxYMT
Micrel, Inc.(6)
1
Notes:
1. TDK: www.tdk.com.
2. Vishay: www.vishay.com.
3. Murata: www.murata.com.
4. FDK: www.fdk.co.jp.
5. Coilcraft: www.coilcraft.com.
6. Micrel, Inc: www.micrel.com.
M9999-061110-E
June 2010
15
Micrel, Inc.
MIC23250
PCB Layout Recommendations (Fixed Output)
Top Layer
Bottom Layer
M9999-061110-E
June 2010
16
Micrel, Inc.
MIC23250
MIC23250 Typical Application Circuit (Adjustable Output)
Bill of Materials
Item
Part Number
Manufacturer
TDK(1)
Description
Qty
C1, C2, C3
C4
C1608X5R0J475K
VJ0603Y103KXXAT
VJ0603Y121KXAAT
CRCW06031002FKEA
CRCW06036653FKEA
CRCW06034423FKEA
LQM21PN1R0MC0D
LQH32CN1R0M33
LQM31PN1R0M00
GLF251812T1R0M
LQM31PNR47M00
MIPF2520D1R5
4.7µF Ceramic Capacitor, 6.3V, X5R, Size 0603
0.01µF Ceramic Capacitor, 25V, X7R, Size 0603
120pF Ceramic Capacitor, 50V, X7R, Size 0603
10kꢀ, 1%, 1/16W, Size 0603
3
Vishay(2)
Vishay(2)
Vishay(2)
Vishay(2)
Vishay(2)
Murata(3)
Murata(3)
Murata(3)
TDK(1)
1
C5, C6
R1, R2
R3, R5
R4, R6
2
Optional
665kꢀ, 1%, 1/16W, Size 0603
2
2
442kꢀ, 1%, 1/16W, Size 0603
1µH, 0.8A, 190mꢀ, L2mm x W1.25mm x H0.5mm
1µH, 1A, 60mꢀ, L3.2mm x W2.5mm x H2.0mm
1µH, 1.2A, 120mꢀ, L3.2mm x W1.6mm x H0.95mm
1µH, 0.8A, 100mꢀ, L2.5mm x W1.8mm x H1.35mm
0.47µH, 1.4A, 80mꢀ, L3.2mm x W1.6mm x H0.85mm
1.5µH, 1.5A, 70mꢀ, L2.5mm x W2mm x H1.0mm
1.0µH, 1.0A, 86mꢀ, L2.0mm x W1.8mm x H1.0mm
4MHz Dual 400mA Adjustable Output
L1, L2
2
Murata(3)
FDK(4)
Coilcraft(5)
EPL2010-102
U1
MIC23250-AAYMT
Micrel, Inc.(6)
1
Buck Regulator with HyperLight Load™ Mode
Notes:
1. TDK: www.tdk.com.
2. Vishay: www.vishay.com.
3. Murata: www.murata.com.
4. FDK: www.fdk.co.jp.
5. Coilcraft: www.coilcraft.com.
6. Micrel, Inc: www.micrel.com.
M9999-061110-E
June 2010
17
Micrel, Inc.
MIC23250
PCB Layout Recommendations (Adjustable Output)
Top Layer
Bottom Layer
M9999-061110-E
June 2010
18
Micrel, Inc.
MIC23250
Package Information (Fixed Output)
10-Pin 2mm x 2mm Thin MLF® (MT)
M9999-061110-E
June 2010
19
Micrel, Inc.
MIC23250
Package Information (Adjustable Output)
12-Pin 2.5mm x 2.5mm Thin MLF® (MT)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its
use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant
into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A
Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully
indemnify Micrel for any damages resulting from such use or sale.
© 2007 Micrel, Incorporated.
M9999-061110-E
June 2010
20
相关型号：
MIC23250-S4YMTTR
1A SWITCHING REGULATOR, 4000kHz SWITCHING FREQ-MAX, PDSO10, 2 X 2 MM, GREEN, MLF-10
MICROCHIP
MIC23250-SKYMTTR
1A SWITCHING REGULATOR, 4000kHz SWITCHING FREQ-MAX, PDSO10, 2 X 2 MM, GREEN, MLF-10
MICROCHIP
MIC23250-W4YMTTR
1A SWITCHING REGULATOR, 4000kHz SWITCHING FREQ-MAX, PDSO10, 2 X 2 MM, GREEN, MLF-10
MICROCHIP
MIC23254
4MHz Dual 400mA Synchronous Buck Regulator with Low Input Voltage and HyperLight Load?
MICREL
MIC23254-GCYMT
4MHz Dual 400mA Synchronous Buck Regulator with Low Input Voltage and HyperLight Load?
MICREL
©2020 ICPDF网 联系我们和版权申明