MIC37301-1.5BRTR [MICROCHIP]
Regulator, 1 Output, 1.5V1, BIPolar;型号: | MIC37301-1.5BRTR |
厂家: | MICROCHIP |
描述: | Regulator, 1 Output, 1.5V1, BIPolar 输出元件 调节器 |
文件: | 总13页 (文件大小:257K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MIC37300/01/02/03
3.0A, Low-Voltage µCap LDO Regulator
General Description
Features
The Micrel MIC37300/01/02/03 is a 3.0A low-dropout
linear voltage regulator that provides a low-voltage,
high-current output with a minimum number of external
components. It offers high precision, ultra-low-dropout
(500mV overtemperature), and low-ground current.
• 3.0A minimum guaranteed output current
• 500mV maximum dropout-voltage overtemperature
–
Ideal for 3.0V to 2.5V conversion
–
Ideal for 2.5V to 1.8V, 1.65V, or 1.5V conversion
• Stable with ceramic or tantalum capacitor
• Wide input voltage range
The MIC37300/01/02/03 operates from an input of
2.25V to 6.0V. It is designed to drive digital circuits
requiring low-voltage at high currents (i.e., PLDs, DSP,
microcontroller, etc.). It is available in fixed and
adjustable output voltages. Fixed voltages include 1.5V,
1.8V, 2.5V and 3.3V. The adjustable version is capable
of 1.24V to 5.5V.
–
VIN: 2.25V to 6.0V
• +1.0% initial output tolerance
• Fixed and adjustable output voltages:
–
–
MIC37300—3-pin fixed voltages
MIC37301—5-pin S-Pak or 8-pin e-Pad SOIC
fixed voltages with flag
Features of the MIC37300/01/02/03 LDO include
thermal and current-limit protection, and reverse-current
protection. Logic enable and error flag pins are available
on the 5-pin version.
–
–
MIC37302—5-pin adjustable voltage
MIC37303—8-pin e-Pad SOIC adjustable
voltage with flag
• Excellent line and load regulation specifications
• Thermal shutdown and current-limit protection
• Reverse-leakage protection
Junction temperature range of the MIC37300/01/02/03
is from–40°C to +125°C.
For applications requiring input voltage greater than
6.0V, see the MIC3910x, MIC3915x, MIC3930x, and
MIC3950x LDOs.
• Low profile S-Pak package
Data sheets and support documentation can be found
on Micrel’s web site at www.micrel.com.
Applications
• LDO linear regulator for low-voltage digital IC
• PC add-in cards
• High-efficiency linear power supplies
• SMPS post regulator
• Battery charger
Typical Application
MIC37300
MIC37302
VIN = 3.0V
VOUT = 2.5V
VIN
1.3V
VIN
VOUT
VIN
VOUT
COUT
47µF, Ceramic
R1
R2
CIN
COUT
47µF, Ceramic
VEN
ADJ
GND
GND
Fixed 2.5V Regulator
Adjustable Regulator
Super ßeta PNP is a registered trademarks of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
1
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
MIC37301
Dropout vs.
Output Current
VIN = 3.0V
CIN
VOUT = 2.5V
VIN
VOUT
500
450
400
350
300
250
200
150
100
50
100k
COUT
47µF, Ceramic
VEN
FLG
2.5VOUT
GND
3.3VOUT
Fixed 2.5 Regulator with Error Flag
0
0
0.5
1
1.5
2
2.5
3
OUTPUT CURRENT (A)
Ordering Information
Part number
Output
Current
Voltage
Junction Temp. Range
Package
Standard
RoHS Compliant* /
Pb-Free
MIC37300-1.5BR
MIC37300-1.65BR
MIC37300-1.5WR*
MIC37300-1.65WR*
3.0A
3.0A
3.0A
3.0A
3.0A
3.0A
3.0A
3.0A
3.0A
3.0A
3.0A
3.0A
3.0A
3.0A
3.0A
1.5V
–40°C to +125°C
–40°C to +125°C
S-Pak-3
S-Pak-3
1.65V
MIC37300-1.8BR
MIC37300-2.5BR
MIC37300-3.3BR
MIC37300-1.8WR*
MIC37300-2.5WR*
MIC37300-3.3WR*
1.8V
2.5V
3.3V
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
S-Pak-3
S-Pak-3
S-Pak-3
MIC37301-1.5YME
MIC37301-1.5WR*
1.5V
1.5V
–40°C to +125°C
–40°C to +125°C
e-Pad SOIC-8
S-Pak-5
MIC37301-1.5BR
MIC37301-1.8BR
MIC37301-1.8YME
MIC37301-1.8WR*
MIC37301-2.5YME
MIC37301-2.5WR*
MIC37301-3.3WR*
MIC37302WR*
1.8V
1.8V
2.5V
2.5V
3.3V
ADJ
ADJ
ADJ
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
e-Pad SOIC-8
S-Pak-5
e-Pad SOIC-8
S-Pak-5
MIC37301-2.5BR
MIC37301-3.3BR
MIC37302BR
S-Pak-5
S-Pak-5
MIC37302BU
MIC37302WU*
TO-263-5
e-Pad SOIC-8
MIC37303YME
* RoHS compliant with ‘high-melting solder’ exemption.
2
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
Pin Configuration
S-PAK-5 (R)
S-PAK-3 (R)
GND
EN
1
2
3
4
8
7
6
5
FLG
5
4
3
2
1
FLG/ADJ
VOUT
GND
VIN
VOUT/ADJ
VOUT
VIN
VIN
EN
VOUT
TO-263-5 (U)
e-Pad SOIC-8 (ME)
Pin Description
Pin Number
S-PAK-5
TO-263-5
Pin Number
S-PAK-3
Pin Number
Pin Name
Pin Function
e-Pad SOIC-8
1
2
EN
Enable Input : CMOS compatible input. Logic high = enable;
Logic low = shutdown.
—
2
1
3, 4
VIN
Input voltage which supplies current to the output power
device.
3
4
2
3
1
5, 6, 7 (Fixed)
5, 6 (Adj.)
8
GND
VOUT
FLG
Ground: TAB is connected to ground.
Regulator Output.
5 (Fixed)
5 (Adj.)
Error Flag (Output): Open collector output. Active-low
indicates an output fault condition.
—
—
7
ADJ
Adjustable Regulator Feedback Input: Connect to resistor
voltage driver.
3
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
Absolute Maximum Ratings(1)
Operating Ratings(2)
Supply Voltage (VIN)............................................. 6.5V
Enable Input Voltage (VEN)(3) ................................ 6.5V
Power Dissipation (PD)(3) .................. Internally Limited
Junction Temperature (TJ).......... –40°C ≤ TJ ≤ +125°C
Storage Temperature (TS).......... –65°C ≤ TJ ≤ +150°C
Lead Temperature (soldering, 5sec)..................260°C
ESD Rating(4)..........................................................2kV
Supply Voltage (VIN).................................2.25V to 6.0V
Enable Input Voltage (VEN)............................0V to 6.0V
Junction Temperature (TJ) ...........–40°C ≤ TJ ≤ +125°C
Package Thermal Resistance
S-Pak (θJC) .................................................. 2°C/W
TO-263-5 (θJC)............................................. 2°C/W
e-Pad SOIC-8 (θJC) ................................... 10°C/W
Electrical Characteristics(5)
TA = 25°C with VIN = VOUT + 1V; VEN = VIN; IL = 10mA; bold values indicate –40°C < TJ < +125°C, unless noted.
Parameter
Conditions
Min
-1
Typ
Max
+1
Units
%
Output Voltage Accuracy
IL = 10mA
10mA < IOUT < IL(max), VOUT + 1 ≤ VIN ≤ 6V
-2
+2
%
Output Voltage Line Regulation
Output Voltage Load Regulation
VIN – VOUT Dropout Voltage(6)
VIN = VOUT + 1.0V to 6.0V; IL = 10mA
IL = 10mA to 3A
0.02
0.2
0.5
1
%
%
IL = 1.5A
(e-Pad SOIC-8)
175
350
400
mV
IL = 3A
(e-Pad SOIC-8)
300
27
500
550
mV
Ground Pin Current(7)
IL = 3A
40
50
mA
mA
Ground Pin Current in Shutdown VIL ≤ 0.5V, VIN = VOUT +1V
1.0
4.75
170
5
µA
A
Current Limit
VOUT = 0V
6.5
500
Start-up Time
VEN = ViN, IOUT = 10mA, COUT = 47µF
µs
Enable Input
Enable Input Threshold
Regulator enable
2.25
V
V
Regulator shutdown
0.8
Enable pin Input Current
VIL ≤ 0.8V (Regulator shutdown)
2
4
µA
µA
µA
µA
VIH ≥ 2.25V (Regulator enable)
1
15
30
75
Flag Output
IFLG(LEAK)
VOH = 6V
1
2
µA
µA
mV
mV
%
VFLG(LO)
VFLG
V
IN = 2.25V, IOL = 250µA(8)
210
2
400
500
Low Threshold, % of VOUT below nominal
Hysteresis
93
%
High Threshold, % of VOUT below nominal
99.2
%
MIC37302 Only
Reference Voltage
1.228
1.215
1.240
40
1.252
1.265
80
V
V
Adjust Pin Bias Current
nA
nA
120
4
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. PD(max) = (TJ(max) – TA) / θJA, where θJA, depends upon the printed circuit layout. See “Applicatins Information.”
4. Devices are ESD sensitive. Handling precautions recommended.
5. Specification for packaged product only.
6. VDO = VIN – VOUT when VOUT decreases to 98% of its nominal output voltage with VIN = VOUT + 1V. For output voltages below 1.75, dropout voltage
specification does not apply due to a minimum input operating voltage of 2.25V.
7. IGND is the quiescent current. IIN = IGND + IOUT
.
8. For a 2.5V device, VIN = 2.250V (device is in dropout).
5
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
Typical Characteristics
Power Supply
Rejection Ratio
Power Supply
Rejection Ratio
Dropout vs.
Output Current
500
450
400
350
300
250
200
150
100
50
80
80
70
60
50
40
30
20
10
0
VIN = 2.5V
OUT = 1.5V
VIN = 2.5V
OUT = 1.5V
70
V
V
60
50
40
30
20
10
0
2.5VOUT
3.3VOUT
IOUT = 3A
IOUT = 3A
COUT = 47µF
IN = 0
C
C
OUT =100µF
IN = 0
C
0
0
0.5
1
1.5
2
2.5
3
0.01 0.1
1
10
100 1000
0.01 0.1
1
10
100 1000
OUTPUT CURRENT (A)
FREQUENCY (kHz)
FREQUENCY (kHz)
Dropout vs.
Tempetature
Dropout Characteristics
(1.5V)
Dropout Characteristics
(2.5V)
450
400
350
300
250
200
150
100
50
1.6
1.4
1.2
1
3
2.5
2
10mA Load
10mA Load
2.5VOUT
0.8
0.6
0.4
0.2
0
1.5
1
3A Load
0.5
0
3A Load
1.9 2.1
0
-40 -20
0
20 40 60 80 100 120
1.5
1.7
2.3
2.5
1.5
2
2.5
3
3.5
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
TEMPERATURE(°C)
Dropout Characteristics
(3.3V)
Ground Current
vs. Output Current
Ground Current
vs. Supply Voltage (1.5V)
50
45
40
35
30
25
20
15
10
5
0.0006
3.5
3
10mA Load
0.0005
0.0004
0.0003
0.0002
0.0001
0
100mA
2.5
2
3A Load
1.5
1
10mA
0.5
0
0
0
1
2
3
4
5
1.5
2
2.5
3
3.5
4
0
0.5
1
1.5
2
2.5
3
SUPPLY VOLTAGE (V)
INPUT VOLTAGE (V)
OUTPUT CURRENT (A)
Ground Current
Ground Current
Ground Current
vs. Supply Voltage (1.5V)
vs. Supply Voltage (2.5V)
vs. Supply Voltage (2.5V)
40
35
30
25
20
15
10
5
1.4
70
60
50
40
30
20
10
0
1.2
1
3A
0.8
0.6
0.4
0.2
0
100mA
10mA
3A
2A
2A
1A
1A
0
0
0
1
2
3
4
5
1
2
3
4
5
0
1
2
3
4
5
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
6
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
Typical Characteristics (continued)
Ground Current
vs. Supply Voltage (3.3V)
Ground Current
vs. Supply Voltage (3.3V)
Ground Current
vs. Temperature
70
60
50
40
30
20
10
0
1.4
1.2
1
0.4
0.35
0.3
2.5V
OUT
3A
0.25
0.2
0.8
0.6
0.4
0.2
0
100mA
0.15
0.1
2A
1A
0.05
0
I
=10mA
10mA
OUT
0
1
2
3
4
5
0
1
2
3
4
5
-40 -20
0
20 40 60 80 100 120
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
Ground Current
vs. Temperature
Ground Current
vs. Temperature
Output Voltage
vs. Temperature
14
12
10
8
45
40
35
30
25
20
15
10
5
2.6
2.5V
OUT
2.55
2.5
2.5V
OUT
2.5V
OUT
6
4
2.45
2
I
=1.5A
I
=3A
0
OUT
OUT
0
0
2.4
-40 -20
-40 -20
0
20 40 60 80 100 120
-40 -20
20 40 60 80 100 120
0
20 40 60 80 100 120
TEMPERATURE(°C)
TEMPERATURE(°C)
TEMPERATURE (°C)
Flag Voltage
vs. Flag Current
Short-Circuit Current
vs. Supply Voltage
Short-Circuit Current
vs. Temperature
6
5.5
5
4.5
4
3.5
3
2.5
2
1.5
1
0.5
0
6
5
4
3
2
1
0
1.0
0.8
0.6
0.4
0.2
0
5V
IN
2.5V
IN
3.3V
IN
2.5V
IN
2.25
3
3.75 4.5 5.25
6
-40 -20
0
20 40 60 80 100 120
0
0.5
1
1.5
2
2.5
3
3.5 4
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
FLAG CURRENT (mA)
Flag Low Voltage
vs. Temperature
Enable Current
vs. Temperature
Error Flag Pull-Up Resistor
400
350
300
250
200
150
100
50
16
14
12
10
8
6
Flag High (OK)
5
4
3
2
1
0
6
2.5V
E N
4
Flag Low (FAULT)
2
Flag Current = 250µA
V
= 5V
IN
0
0
0.01 0.1
1
10 100 1000 10000
-40 -20
0
20 40 60 80 100 120
-40 -20
0
20 40 60 80 100 120
TEMPERATURE(°C)
TEMPERATURE(°C)
7
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
Functional Characteristics
Load Transient Response
Line Transient Response
VIN = 3.3V
VOUT = 2.5V
COUT = 47µF Ceramic
COUT = 47µF Ceramic
3A
5V
3.3V
10mA
TIME (400µs/dvi.)
TIME (100µs/dvi.)
Enable Transient Response
IOUT = 3A
VIN = 3.3V
COUT = 47µF
2.5V
TIME (40µs/div.)
8
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
Where TJ(max) < 125°C and θCS is between 0°C and
2°C/W. The heat sink may be significantly reduced in
applications where the minimum input voltage is
known and is large compared with the dropout
voltage. Use a series input resistor to drop excessive
voltage and distribute the heat between this resistor
and the regulator. The low-dropout properties of
Micrel’s Super ßeta PNP® regulators allow significant
reductions in regulator power dissipation and the
Applications Information
Enable/Shutdown
The MIC37300/01/02/03 is a high-performance low-
dropout voltage regulator suitable for moderate to
high-current regulator applications. Its 500mV dropout
voltage at full load and over-temperature makes it
especially valuable in battery-powered systems and
as high-efficiency noise filters in post-regulator
applications. Unlike older NPN-pass transistor
designs, there the minimum dropout voltage is limited
by the based-to-emitter voltage drop and collector-to-
emitter saturation voltage, dropout performance of the
PNP output of these devices is limited only by the low
VCE saturation voltage.
associated
heat
sink
without
compromising
performance. When this technique is employed, a
capacitor of at least 1.0µF is needed directly between
the input and regulator ground.
Refer to “Application Note 9” for further details and
examples on thermal design and heat sink
applications.
A trade-off for the low dropout voltage is a varying
base drive requirement. Micrel’s Super ßeta PNP®
process reduces this drive requirement to only 2% to
5% of the load current.
Output Capacitor
The MIC37300/01/02/03 requires an output capacitor
for stable operation. As
a
µCap LDO, the
The MIC37300/01/02/03 regulator is fully protected
from damage due to fault conditions. Current limiting
is provided. This limiting is linear; output current
during overload conditions is constant. Thermal
shutdown disables the device when the die
temperature exceeds the maximum safe operating
temperature. The output structure of these regulators
allows voltages in excess of the desired output
voltage to be applied without reverse current flow.
MIC37300/01/02/03 can operate with ceramic output
capacitors as long as the amount of capacitance is
47µF or greater. For values of output capacitance
lower than 47µF, the recommended ESR range is
200mΩ to 2Ω. The minimum value of output
capacitance recommended for the MIC37300 is 10µF.
For 47µF or greater, the ESR range recommended is
less than 1Ω. Ultra-low ESR, ceramic capacitors are
recommended for output capacitance of 47µF or
greater to help improve transient response and noise
reduction at high frequency. X7R/X5R dielectric-type
ceramic capacitors are recommended because of
their temperature performance. X7R-type capacitors
change capacitance by 15% over their operating
temperature range and are the most stable type of
ceramic capacitors. Z5U and Y5V dielectric capacitors
change value by as much as 50% and 60%,
respectively, over their operating temperature ranges.
To use a ceramic chip capacitor with Y5V dielectric,
the value must be much higher than an X7R ceramic
capacitor to ensure the same minimum capacitance
over the equivalent operating temperature range.
Thermal Design
Linear regulators are simple to use. The most
complicated design parameters to consider are
thermal characteristics. Thermal design requires the
following application-specific parameters:
•
•
•
•
•
Maximum ambient temperature (TA)
Output current (IOUT
)
Output voltage (VOUT
Input voltage (VIN)
)
Ground current (IGND
)
First, calculate the power dissipation of the regulator
from these numbers and the device parameters from
this datasheet.
Input Capacitor
An input capacitor of 1.0µF or greater is
recommended when the device is more than 4 inches
away from the bulk supply capacitance, or when the
supply is a battery. Small, surface-mount chip
capacitors can be used for the bypassing. The
capacitor should be place within 1" of the device for
optimal performance. Larger values will help to
improve ripple rejection by bypassing the input to the
regulator, further improving the integrity of the output
voltage.
PD = (VIN – VOUT) IOUT + VIN IGND
where the ground current is approximated by using
numbers from the “Electrical Characteristics” or
“Typical Characteristics.” Then the heat sink thermal
resistance is determined with this formula:
θ
SA = ((TJ(max) – TA)/ PD) – (θJC + θCS)
9
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
Transient Response and 3.3V to 2.5V, 2.5V to 1.8V
or 1.65V, or 2.5V to 1.5V Conversions
Enable Input
The MIC37301/02/03 also features an enable input for
on/off control of the device. Its shutdown state draws
“zero” current (only microamperes of leakage). The
enable input is TTL/CMOS compatible for simple logic
interface, but can be connected up to VIN. When
enabled, it draws approximately 15µA.
The MIC37300/01/02/03 has excellent transient
response to variations in input voltage and load
current. The device has been designed to respond
quickly to load current variations and input voltage
variations. Large output capacitors are not required to
obtain this performance. A standard 47µF output
capacitor, preferably tantalum, is all that is required.
Larger values help to improve performance even
further.
Adjustable Regulator Design
MIC37302
VIN
IN
OUT
VOUT
COUT
By virtue of its low-dropout voltage, this device does
not saturate into dropout as readily as similar NPN-
based designs. When converting from 3.3V to 2.5V,
2.5V to 1.8V or 1.65V, or 2.5V to 1.5V, the NPN-
based regulators are already operating in dropout,
with typical dropout requirements of 1.2V or greater.
To convert down to 2.5V without operating in dropout,
NPN-based regulators require an input voltage of 3.7V
at the very least. The MIC37300/01/02/03 regulator
will provide excellent performance with an input as low
as 3.0V or 2.25V, respectively. This gives the PNP-
based regulators a distinct advantage over older,
NPN-based linear regulators.
R1
R2
ENABLE
SHUTDOWN
EN
ADJ
GND
R1
R2
⎛
⎞
⎟
⎠
VOUT = 1.240V 1+
⎜
⎝
Figure 1. Adjustable Regulator with Resistors
The MIC37302 and MIC37303 allow programming the
output voltage any-where between 1.24V and the
5.5V maximum operating rating of the family. Two
resistors are used. Resistors can be quite large, up to
1MΩ, because of the very high input impedance and
low bias current of the sense comparator. The resistor
values are calculated by:
Minimum Load Current
The MIC37300/01/02/03 regulator is specified
between finite loads. If the output current is too small,
leakage currents dominate and the output voltage
rises. A 10mA minimum load current is necessary for
proper operation.
V
⎛
⎞
OUT
R1 = R2⎜
− 1⎟
⎜
⎟
1.240
⎝
⎠
Where VOUT is the desired output voltage. Figure 1
shows component definition. Applications with widely
varying load currents may scale the resistors to draw
the minimum load current required for proper
operation (see above).
Error Flag
The MIC37301 and MIC37303 feature an error flag
circuit that monitors the output voltage and signals an
error condition when the voltage is 5% below the
nominal output voltage. The error flag is an open-
collector output that can sink 10mA during a fault
condition.
Low output voltage can be caused by a number of
problems, including an overcurrent fault (device in
current limit) or low input voltage. The flag is
inoperative during overtemperature shutdown.
10
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
Package Information
θ4
θ1
θ2
θ1
θ3
θ1
θ2
θ3
θ4
5-Pin TO-263-5 (U)
5-Pin S-PAK (R)
11
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
3-Pin S-PAK (R)
8-Pin SOIC (ME)
12
M9999-102909
October 2009
Micrel, Inc.
MIC37300/01/02/03
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for
its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a
product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for
surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant
injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk
and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale.
© 2002 Micrel, Inc.
13
M9999-102909
October 2009
相关型号:
MIC37301-1.8WRTR
1.8V FIXED POSITIVE LDO REGULATOR, 0.55V DROPOUT, PSSO5, ROHS COMPLIANT, SPAK-5
MICREL
©2020 ICPDF网 联系我们和版权申明