MIC5200-5.0YMM-TR [MICROCHIP]
5V FIXED POSITIVE LDO REGULATOR, 0.35V DROPOUT, PDSO8;
| 型号： | MIC5200-5.0YMM-TR |
| 厂家： | 
MICROCHIP |
| 描述： | 5V FIXED POSITIVE LDO REGULATOR, 0.35V DROPOUT, PDSO8 光电二极管 输出元件 调节器 |
| 文件： | 总24页 (文件大小：1631K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MIC5200
100 mA Low-Dropout Regulator
Features
General Description
• High Output Voltage Accuracy
• Variety of Output Voltages
The MIC5200 is an efficient linear voltage regulator
with very low dropout voltage (typically 17 mV at light
loads and 200 mV at 100 mA), and very low ground
current (1 mA at 100 mA output), offering better than
1% initial accuracy with a logic-compatible ON/OFF
switching input. Designed especially for hand-held
battery-powered devices, the MIC5200 is switched by
a CMOS- or TTL-compatible logic signal. The ENABLE
control may be tied directly to VIN if unneeded. When
disabled, power consumption drops nearly to zero. The
ground current of the MIC5200 increases only slightly
in dropout, further prolonging battery life. Key MIC5200
features include protection against reversed battery,
current limiting, and overtemperature shutdown.
• Guaranteed 100 mA Output
• Low Quiescent Current
• Low Dropout Voltage
• Extremely Tight Load and Line Regulation
• Very Low Temperature Coefficient
• Current and Thermal Limiting
• Zero OFF Mode Current
• Logic-Controlled Electronic Shutdown
• Available in 8-Lead SOIC, MM8 8-Lead MSOP,
and SOT-223 Packages
The MIC5200 is available in several fixed voltages and
accuracy configurations. Other options are available;
contact Microchip for details.
Applications
• Cellular Telephones
• Laptop, Notebook, and Palmtop Computers
• Battery-Powered Equipment
• PCMCIA VCC and VPP Regulation/Switching
• Barcode Scanners
• SMPS Post-Regulator/DC-to-DC Modules
• High Efficiency Linear Power Supplies
Typical Application Schematic
MIC5200-3.3
OUTPUT
1μF
ENABLE
2016 Microchip Technology Inc.
DS20005578A-page 1
MIC5200
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Input Supply Voltage ................................................................................................................................... –20V to +60V
Enable Input Voltage ................................................................................................................................... –20V to +60V
Power Dissipation...................................................................................................................................Internally Limited
Operating Ratings ‡
Input Voltage ..............................................................................................................................................+2.5V to +26V
Enable Input Voltage ...................................................................................................................................... –20V to VIN
† Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
‡ Notice: The device is not guaranteed to function outside its operating ratings.
DS20005578A-page 2
2016 Microchip Technology Inc.
MIC5200
TABLE 1-1:
ELECTRICAL CHARACTERISTICS
Electrical Characteristics: Limits in standard typeface are for TJ = 25°C and limits in boldface apply over the
junction temperature range of –40°C to +125°C. Unless otherwise specified, VIN = VOUT + 1V, IL = 1 mA, CL = 3.3 μF,
and VENABLE = VDD. (Note 1).
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
–1
—
—
1
Output Voltage Accuracy
VO
%
Variation from specified VOUT
–2
2
Output Voltage Temperature
Coefficient
∆VO/∆T
∆VO/VIN
—
40
150
ppm/°C
%
Note 2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.004
—
0.10
0.40
0.16
0.30
—
Line Regulation
Load Regulation
VIN = VOUT + 1V to 26V
0.04
—
∆V /V
%
IL = 0.1 mA to 100 mA (Note 3)
O
OUT
17
IL = 100 µA
IL = 20 mA
130
150
190
230
0.01
130
270
330
500
1000
70
—
Dropout Voltage (Note 4)
Quiescent Current
VIN – VO
—
mV
µA
µA
IL = 30 mA
—
IL = 50 mA
350
10
IL = 100 mA
IGND
VENABLE ≤ 0.7V (shutdown)
VENABLE = VDD, IL = 100 µA
IL = 20 mA
—
350
—
Ground Pin Current
IGND
IL = 30 mA
—
IL = 50 mA
1500
—
IL = 100 mA
Ripple Rejection
PSRR
dB
µA
—
VIN = 0.5V less than specified
VOUT, IL = 100 µA (Note 5)
Ground Pin Current at Dropout
IGNDDO
—
270
330
Current Limit
ILIMIT
∆VO/∆PD
en
100
—
250
0.05
100
—
—
—
mA
%/W
µV
VOUT = 0V
Note 6
—
Thermal Regulation
Output Noise
—
Note 1: Specification for packaged product only.
2: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total
temperature range.
3: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are
tested for load regulation in the load range from 0.1 mA to 100 mA. Changes in output voltage due to
heating effects are covered by the thermal regulation specification.
4: Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its
nominal value measured at 1V differential.
5: Ground pin current is the regulator quiescent current plus pass transistor base current. The total current
drawn from the supply is the sum of the load current plus the ground pin current.
6: Thermal regulation is defined as the change in output voltage at a time (t) after a change in power dissipa-
tion is applied, excluding load or line regulation effects. Specifications are for a 100 mA load pulse at VIN
26V for t = 10 ms.
=
2016 Microchip Technology Inc.
DS20005578A-page 3
MIC5200
TABLE 1-1:
ELECTRICAL CHARACTERISTICS (CONTINUED)
Electrical Characteristics: Limits in standard typeface are for TJ = 25°C and limits in boldface apply over the
junction temperature range of –40°C to +125°C. Unless otherwise specified, VIN = VOUT + 1V, IL = 1 mA, CL = 3.3 μF,
and VENABLE = VDD. (Note 1).
Parameters
ENABLE Input
Sym.
Min.
Typ.
Max.
Units
Conditions
Input Voltage Level, Logic Low
Input Voltage Level, Logic High
VIL
VIH
IIL
—
2.0
—
—
—
0.7
—
1
OFF
ON
V
0.01
15
VIL ≤ 0.7V
VIH ≥ 2.0V
Enable Input Current
µA
IIH
—
50
Note 1: Specification for packaged product only.
2: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total
temperature range.
3: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are
tested for load regulation in the load range from 0.1 mA to 100 mA. Changes in output voltage due to
heating effects are covered by the thermal regulation specification.
4: Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its
nominal value measured at 1V differential.
5: Ground pin current is the regulator quiescent current plus pass transistor base current. The total current
drawn from the supply is the sum of the load current plus the ground pin current.
6: Thermal regulation is defined as the change in output voltage at a time (t) after a change in power dissipa-
tion is applied, excluding load or line regulation effects. Specifications are for a 100 mA load pulse at VIN
26V for t = 10 ms.
=
DS20005578A-page 4
2016 Microchip Technology Inc.
MIC5200
TEMPERATURE SPECIFICATIONS
Parameters
Temperature Ranges
Sym.
Min.
Typ.
Max.
Units
Conditions
Junction Operating Temperature
Range
TJ
—
–40
—
—
—
+125
+260
°C
°C
Note 1
Lead Temperature
Soldering, 5s
—
Package Thermal Resistances
Thermal Resistance, SOT-223
Thermal Resistance, SOIC-8
JC
JA
—
—
15
—
—
°C/W
160
°C/W Note 2
Note 1: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., TA, TJ, JA). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability.
2: The maximum allowable power dissipation at any ambient temperature is calculated using: P(MAX)
=
(TJ(MAX) – TA) ÷ θJA. Exceeding the maximum allowable power dissipation will result in excessive die tem-
perature, and the regulator will go into thermal shutdown. The θJC of the MIC5200-x.xYS is 15°C/W and
θJA for the MIC5200YM is 160°C/W mounted on a PC board (see Thermal Considerations for further
details).
2016 Microchip Technology Inc.
DS20005578A-page 5
MIC5200
2.0
TYPICAL PERFORMANCE CURVES
Note: The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
250
200
150
100
50
10
1
0
0.1
0.01 0.1
1
10
100 1000
0.01
0.1
1
10
100
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
FIGURE 2-1:
Dropout Voltage vs. Output
FIGURE 2-4:
Ground Current vs. Output
Current.
Current.
0.4
0.3
0.2
0.1
0.0
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
IL = 100mA
IL = 100mA
IL = 1mA
IL = 1mA
-60 -30
0
30 60 90 120 150
0
2
4
6
8
10
TEMPERATURE (°C)
SUPPLY VOLTAGE (V)
FIGURE 2-2:
Dropout Voltage vs.
FIGURE 2-5:
Ground Current vs. Supply
Temperature.
Voltage.
3.5
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
3.0
2.5
2.0
1.5
1.0
0.5
0.0
IL = 100mA
CIN = 2.2μF
C
OUT = 4.7μF
IL = 100μA, 1mA
0
2
4
6
8
10
0.0
0.1
0.2
0.3
INPUT VOLTAGE (V)
OUTPUT CURRENT (A)
FIGURE 2-3:
Dropout Characteristics.
FIGURE 2-6:
Output Voltage vs. Output
Current.
DS20005578A-page 6
2016 Microchip Technology Inc.
MIC5200
0.30
0.25
0.20
0.15
3.6
3.5
3.4
3.3
3.2
3.1
3.0
CIN = 2.2μF
OUT = 4.7μF
ILOAD = 100μA
C
CIN = 2.2μF
C
OUT = 4.7μF
3 DEVICES:
HI / AVG / LO
CURVES APPLICABLE
AT 100μA AND 100mA
-60 -30
0
30 60 90 120 150
-60 -30
0
30 60 90 120 150
TEMPERATURE (°C)
TEMPERATURE (°C)
FIGURE 2-7:
Ground Current vs.
FIGURE 2-10:
Output Voltage vs.
Temperature.
Temperature (3.3V Version).
300
280
260
240
220
200
180
160
140
120
100
1.5
1.4
1.3
1.2
1.1
1.0
ILOAD = 100mA
CIN = 2.2μF
COUT = 4.7μF
VOUT = 3.3V
VOUT = 0V
(SHORT CIRCUIT)
-60 -30
0
30 60 90 120 150
-50
0
50
100
150
TEMPERATURE (°C)
TEMPERATURE (°C)
FIGURE 2-11:
Temperature.
Output Current vs.
FIGURE 2-8:
Temperature.
Ground Current vs.
3.30
3.29
3.28
3.27
3.26
3.25
3.24
3.23
3.22
3.21
3.20
100
50
CIN = 2.2μF
C
OUT = 4.7μF
0
ILOAD = 1mA
CL = 4.7 μF
2-050
100
0
-100
-60 -30
0
30 60 90 120 150
-5
0
5
10 15 20 25 30 35
TIME (ms)
TEMPERATURE (°C)
FIGURE 2-12:
Temperature.
Minimum Input Voltage vs.
FIGURE 2-9:
Version).
Thermal Regulation (3.3V
2016 Microchip Technology Inc.
DS20005578A-page 7
MIC5200
300
250
200
150
100
50
120
100
80
60
40
20
0
CIN = 2.2μF
OUT = 4.7μF
OUT = 3.3V
RL = 33Ω
C
V
0
1
2
3
4
5
6
7
0 1 2 3 4 5 6 7 8 9 10
INPUT VOLTAGE (V)
SUPPLY VOLTAGE (V)
FIGURE 2-13:
Short Circuit Current vs.
FIGURE 2-16:
Supply Current vs. Supply
Input Voltage.
Voltage (3.3V Version).
10
5
20
10
0
-10
-20
3-030
CL = 1 μF
L = 1mA
I
0
-5
CL = 4.7μF
-108
6
4
2
200
100
0
-0.2
0
0.2
0.4
0.6
0.8
-2
0
2
4
6
8
10
TIME (ms)
TIME (ms)
FIGURE 2-14:
Load Transient.
FIGURE 2-17:
Line Transient.
20
10
0
-10
-20
3-030
15
10
5
CL = 10 μF
I
L = 1mA
CL = 47μF
0
-85
200
100
0
6
4
2
-10
0
10
20
30
40
-0.1
0
0.1 0.2 0.3 0.4 0.5 0.6
TIME (ms)
TIME (ms)
FIGURE 2-15:
Load Transient.
FIGURE 2-18:
Line Transient.
DS20005578A-page 8
2016 Microchip Technology Inc.
MIC5200
1000
100
10
60
50
40
30
20
10
0
IL = 100μA
IL = 1mA
1
0.1
RL = 66Ω
0.01
0.001
IL = 100mA
0
1
2
3
4
5
6
7
SUPPLY VOLTAGE (V)
FREQUENCY (Hz)
FIGURE 2-22:
Output Impedance.
FIGURE 2-19:
Supply Current vs. Supply
Voltage (3.3V Version).
5
4
35
30
25
20
15
10
5
CIN = 2.2μF
3
COUT = 4.7μF
2
CL = 4.7 μF
L = 1mA
1
I
0
-41
VEN = 5V
2
0
VEN = 2V
0
-2
-5
-50
0
50 100 150 200 250 300
-60 -30
0
30 60 90 120 150
TIME (μs)
TEMPERATURE (°C)
FIGURE 2-23:
vs. Temperature.
Enable Current Threshold
FIGURE 2-20:
Version).
Enable Transient (3.3V
5
4
1.6
1.4
1.2
1
CIN = 2.2μF
3
2
C
OUT = 4.7μF
CL = 4.7 μF
1
IL = 100mA
0
-41
ON
2
0
0.8
0.6
0.4
OFF
-2
-50
0
50 100 150 200 250 300
-60 -30
0
30 60 90 120 150
TEMPERATURE (°C)
TIME (μs)
FIGURE 2-24:
vs. Temperature.
Enable Voltage Threshold
FIGURE 2-21:
Version).
Enable Transient (3.3V
2016 Microchip Technology Inc.
DS20005578A-page 9
MIC5200
100
80
60
40
20
0
IL = 100μA
FREQUENCY (Hz)
FIGURE 2-25:
Ripple vs. Frequency.
100
80
60
40
20
0
IL = 1mA
FREQUENCY (Hz)
FIGURE 2-26:
Ripple vs. Frequency.
100
80
60
40
20
0
IL = 100mA
FREQUENCY (Hz)
FIGURE 2-27:
Ripple vs. Frequency.
DS20005578A-page 10
2016 Microchip Technology Inc.
MIC5200
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
Package Types
MIC5200-x.xYS
SOT-223 (S)
(Top View)
MIC5200-x.xYM
SOIC-8 (M)
MIC5200-x.xYMM
MSOP-8 (MM)
(Top View)
OUT
OUT
IN
IN
NC
EN
NC
GND
2
3
1
IN GND OUT
TABLE 3-1:
PIN FUNCTION TABLE
Pin Number
Pin Number
SOT-223
SOIC-8,
MSOP-8
Pin Name
Description
3
—
1, 2
3, 6
4
OUT
NC
Output: Pins 1 and 2 (SOIC-8, MSOP-8 packages) must be
externally connected together.
Not internally connected. Connect to ground place for lowest
thermal resistance.
2, TAB
—
GND
EN
Ground: Ground pin and TAB (SOT-223 package) are internally
connected.
5
Enable/Shutdown (Input): TTL-compatible. High = enabled; low =
shutdown.
1
7, 8
IN
Supply Input: Pins 7 and 8 (SOIC-8, MSOP-8 packages) must be
externally connected together.
2016 Microchip Technology Inc.
DS20005578A-page 11
MIC5200
4.0
4.1
APPLICATION INFORMATION
External Capacitors
A 1 μF capacitor is recommended between the
MIC5200 output and ground to prevent oscillations due
to instability. Larger values serve to improve the
regulator's transient response. Most types of tantalum
or aluminum electrolytics will be adequate; film types
will work, but are costly and therefore not
recommended. Many aluminum electrolytics have
electrolytes that freeze at about –30°C, so solid
tantalum capacitors are recommended for operation
below –25°C. The important parameters of the
capacitor are an effective series resistance of about 5Ω
or less and a resonant frequency above 500 kHz. The
value of this capacitor may be increased without limit.
At lower values of output current, less output
capacitance is required for output stability. The
capacitor can be reduced to 0.47 μF for current below
10 mA or 0.33 μF for currents below 1 mA. A 1 μF
capacitor should be placed from the MIC5200 input to
ground if there is more than 10 inches of wire between
the input and the AC filter capacitor or if a battery is
used as the input.
The MIC5200 will remain stable and in regulation with
no load in addition to the internal voltage divider, unlike
many other voltage regulators. This is especially
important in CMOS RAM keep-alive applications.
When used in dual supply systems where the regulator
load is returned to a negative supply, the output voltage
must be diode clamped to ground.
4.2
ENABLE Input
The MIC5200 features nearly zero OFF mode current.
When the ENABLE input is held below 0.7V, all internal
circuitry is powered off. Pulling this pin high (over 2.0V)
re-enables the device and allows operation. The
ENABLE pin requires a small amount of current,
typically 15 μA. While the logic threshold is TTL/CMOS
compatible, ENABLE may be pulled as high as 30V,
independent of the voltage on VIN.
DS20005578A-page 12
2016 Microchip Technology Inc.
MIC5200
5.0
5.1
THERMAL CONSIDERATIONS
Layout
The MIC5200-x.xYM (8-pin surface mount package)
has the following thermal characteristics when
mounted on a single-layer copper-clad printed circuit
board.
PC Board Dielectric
JA
FR4
160 °C/W
120 °C/W
Ceramic
Multi-layer boards having a ground plane, wide traces
near the pads, and large supply bus lines provide better
thermal conductivity.
The "worst case" value of 160 °C/W assumes no
ground plane, minimum trace widths, and a FR4
material board.
5.2
Nominal Power Dissipation and
Die Temperature
The MIC5200-x.xYM at a 25°C ambient temperature
will operate reliably at up to 625 mW power dissipation
when mounted in the "worst case" manner described
above. At an ambient temperature of 55°C, the device
may safely dissipate 440 mW. These power levels are
equivalent to a die temperature of 125°C, the
recommended maximum temperature for non-military
grade silicon integrated circuits.
For MIC5200-x.xYS (SOT-223 package) heat sink
characteristics, please refer to Application Hint 17,
“Calculating P.C. Board Heat Sink Area for Surface
Mount Packages”.
2016 Microchip Technology Inc.
DS20005578A-page 13
MIC5200
6.0
6.1
PACKAGING INFORMATION
Package Marking Information
8-Pin SOIC*
Example
5200
XXXX
XXYM
YYWWC
30YM
1610C
SOT-223*
Example
XXXX
X.XYSYWWP
5200
3.0YS618P
8-Pin MSOP*
Example
XXXX
X.XY
5200
3.3Y
Legend: XX...X Product code or customer-specific information
Y
Year code (last digit of calendar year)
YY
WW
NNN
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
e
3
*
)
e
3
●, ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle
mark).
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information. Package may or may not include
the corporate logo.
Underbar (_) symbol may not be to scale.
DS20005578A-page 14
2016 Microchip Technology Inc.
MIC5200
SOT-223 Package Outline and Recommended Land Pattern
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2016 Microchip Technology Inc.
DS20005578A-page 15
MIC5200
8-Lead MSOP Package Outline and Recommended Land Pattern
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS20005578A-page 16
2016 Microchip Technology Inc.
MIC5200
8-Lead SOIC-N Package Outline and Recommended Land Pattern
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2016 Microchip Technology Inc.
DS20005578A-page 17
MIC5200
DS20005578A-page 18
2016 Microchip Technology Inc.
MIC5200
APPENDIX A: REVISION HISTORY
Revision A (July 2016)
• Converted Micrel document MIC5200 to Micro-
chip data sheet DS20005578A.
• Minor text changes throughout.
2016 Microchip Technology Inc.
DS20005578A-page 19
MIC5200
NOTES:
DS20005578A-page 20
2016 Microchip Technology Inc.
MIC5200
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office.
Examples:
–
PART NO.
Device
–
X.X
X
XX
X.X
a)
b)
c)
d)
e)
f)
MIC5200-3.0YM:
100 mA Low-Dropout Reg-
ulator, 3.0V Voltage, –40°C
to +125°C Temp. Range, 8-
Pin SOIC, 95/Tube
Voltage
Media Type
Temperature Package
MIC5200-4.8YM-TR:
MIC5200-3.3YMM:
100 mA Low-Dropout Reg-
ulator, 4.85 Voltage, –40°C
to +125°C Temp. Range, 8-
Pin SOIC, 2,500/Reel
Device:
MIC5200:
100 mA Low-Dropout Regulator
Voltage:
(Note 1)
3.0
3.3
4.8
5.0
=
=
=
=
3.0V
3.3V
4.8V
5.0V
100 mA Low-Dropout Regu-
lator, 3.3V Voltage, –40°C
to +125°C Temp. Range, 8-
Pin MSOP, 95/Tube
Temperature:
Package:
Y
=
–40°C to +125°C
MIC5200-5.0YMM-TR: 100 mA Low-Dropout Reg-
ulator, 5.0V Voltage, –40°C
to +125°C Temp. Range, 8-
Pin MSOP, 2,500/Reel
M
MM
S
=
=
=
8-Pin SOIC
8-Pin MSOP
SOT-223
MIC5200-3.3YS:
100 mA Low-Dropout Reg-
ulator, 3.3V Voltage, –40°C
to +125°C Temp. Range,
SOT-223, 95/Tube
Media Type:
TR
blank=
=
2,500/Reel
95/Tube
MIC5200-5.0YS-TR
100 mA
Low-Dropout
Note 1:
The 8-Pin MSOP package (MM) is only available in 3.3V and
5.0V options.
Regulator, 5.0V Voltage,
–40°C to +125°C Temp.
Range, SOT-223, 2,500/
Reel
2016 Microchip Technology Inc.
DS20005578A-page 21
MIC5200
NOTES:
DS20005578A-page 22
2016 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, AnyRate,
dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KeeLoq,
KeeLoq logo, Kleer, LANCheck, LINK MD, MediaLB, MOST,
MOST logo, MPLAB, OptoLyzer, PIC, PICSTART, PIC32 logo,
RightTouch, SpyNIC, SST, SST Logo, SuperFlash and UNI/O
are registered trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
ClockWorks, The Embedded Control Solutions Company,
ETHERSYNCH, Hyper Speed Control, HyperLight Load,
IntelliMOS, mTouch, Precision Edge, and QUIET-WIRE are
registered trademarks of Microchip Technology Incorporated
in the U.S.A.
Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut,
BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM,
dsPICDEM.net, Dynamic Average Matching, DAM, ECAN,
EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-Chip
Connectivity, JitterBlocker, KleerNet, KleerNet logo, MiWi,
motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB,
MPLINK, MultiTRAK, NetDetach, Omniscient Code
Generation, PICDEM, PICDEM.net, PICkit, PICtail,
PureSilicon, RightTouch logo, REAL ICE, Ripple Blocker,
Serial Quad I/O, SQI, SuperSwitcher, SuperSwitcher II, Total
Endurance, TSHARC, USBCheck, VariSense, ViewSpan,
WiperLock, Wireless DNA, and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
GestIC is a registered trademarks of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip
Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
QUALITYꢀMANAGEMENTꢀꢀSYSTEMꢀ
CERTIFIEDꢀBYꢀDNVꢀ
© 2016, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
ISBN: 978-1-5224-0785-0
== ISO/TSꢀ16949ꢀ==ꢀ
2016 Microchip Technology Inc.
DS20005578A-page 23
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Asia Pacific Office
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Web Address:
www.microchip.com
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Germany - Dusseldorf
Tel: 49-2129-3766400
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Germany - Karlsruhe
Tel: 49-721-625370
India - Pune
Tel: 91-20-3019-1500
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Austin, TX
Tel: 512-257-3370
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Boston
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
China - Dongguan
Tel: 86-769-8702-9880
Italy - Venice
Tel: 39-049-7625286
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Guangzhou
Tel: 86-20-8755-8029
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
Korea - Seoul
Cleveland
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Poland - Warsaw
Tel: 48-22-3325737
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Sweden - Stockholm
Tel: 46-8-5090-4654
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Detroit
Novi, MI
Tel: 248-848-4000
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Houston, TX
Tel: 281-894-5983
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Los Angeles
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Taiwan - Kaohsiung
Tel: 886-7-213-7828
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
06/23/16
DS20005578A-page 24
2016 Microchip Technology Inc.
相关型号：
MIC5200-5.0YSTR
5V FIXED POSITIVE LDO REGULATOR, 0.35V DROPOUT, PDSO4, LEAD FREE, SOT-223, 3 PIN
MICROCHIP
MIC5201-3.0BST&R
Fixed Positive LDO Regulator, 3V, 0.4V Dropout, BIPolar, PDSO4, SOT-223, 4 PIN
MICREL
©2020 ICPDF网 联系我们和版权申明