MIC5207-3.3YM5-TR [MICROCHIP]
IC REG LDO 3.3V 0.18A SOT23-5;型号: | MIC5207-3.3YM5-TR |
厂家: | MICROCHIP |
描述: | IC REG LDO 3.3V 0.18A SOT23-5 光电二极管 输出元件 调节器 |
文件: | 总22页 (文件大小:1357K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MIC5207
180 mA Low-Noise LDO Regulator
Features
General Description
• Output Voltage Range: 1.8V – 15V
• Ultra-Low-Noise Output
The MIC5207 is an efficient linear voltage regulator
with ultra-low-noise output, very low dropout voltage
(typically 17 mV at light loads and 165 mV at 150 mA),
and very low ground current (720 µA at 100 mA
output). The MIC5207 offers better than 3% initial
accuracy.
• High Output Voltage Accuracy
• Guaranteed 180 mA Output
• Low Quiescent Current
• Low Dropout Voltage
Designed especially for hand-held, battery-powered
devices, the MIC5207 includes a CMOS or TTL
compatible enable/shutdown control input. When in
shutdown, power consumption drops nearly to zero.
• Extremely Tight Load and Line Regulation
• Very Low Temperature Coefficient
• Current and Thermal Limiting
• Reversed-Battery Protection
• “Zero” Off-Mode Current
Key MIC5207 features include a reference bypass pin
to improve its already low-noise performance,
reversed-battery protection, current limiting, and over
temperature shutdown.
• Logic-Controlled Electronic Enable
Applications
• Cellular Telephones
The MIC5207 is available in fixed and adjustable output
voltage versions in a small SOT-23-5 package. Contact
Microchip for details.
• Laptop, Notebook, and Palmtop Computers
• Battery Powered Equipment
For low-dropout regulators that are stable with ceramic
output capacitors, see the µCap MIC5245/6/7 family.
• PCMCIA VCC and VPP Regulation/Switching
• Consumer/Personal Electronics
• SMPS Post-Regulator and DC/DC Modules
• High-Efficiency Linear Power Supplies
Package Types
MIC5207 (FIXED)
SOT-23-5 (M5)
TSOT-23-5 (D5)
(Top View)
MIC5207 (ADJ.)
SOT-23-5 (M5)
(Top View)
EN GND IN
EN GND IN
3
2
1
3
2
1
PART
IDENTIFICATION
LEAA
LExx
4
ADJ
5
OUT
4
BYP
5
OUT
2017 Microchip Technology Inc.
DS20005719A-page 1
MIC5207
Typical Application Circuit
MIC5207
SOT-23-5
BATTERY-POWERED REGULATOR APPLICATION
MIC5207-x.xYM5
VIN
VOUT
COUT
1
2
3
5
EN
ENABLE
SHUTDOWN
4
ENABLE (PIN 3) MAY BE
CONNECTED DIRECTLY TO
SUPPLY INPUT (PIN 1).
Functional Diagrams
ULTRA-LOW-NOISE
FIXED REGULATOR
OUT
IN
VOUT
COUT
VIN
BYP
C BYP
(OPTIONAL)
BANDGAP
REF.
EN
CURRENT LIMIT
THERMAL SHUTDOWN
MIC5207-X.XYM5
GND
ULTRA-LOW-NOISE
ADJUSTABLE REGULATOR
OUT
IN
VOUT
COUT
VIN
R1
R2
ADJ
CBYP
(OPTIONAL)
BANDGAP
REF.
EN
CURRENT LIMIT
THERMAL SHUTDOWN
MIC5207YM5
GND
DS20005719A-page 2
2017 Microchip Technology Inc.
MIC5207
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Supply Input Voltage (VIN) .......................................................................................................................... –20V to +20V
Enable Input Voltage (VEN) ......................................................................................................................... –20V to +20V
Power Dissipation (PD) (Note 1) ............................................................................................................Internally Limited
Operating Ratings ‡
Supply Input Voltage (VIN) ......................................................................................................................... +2.5V to +16V
Adjustable Output Voltage Range (VOUT) .................................................................................................. +1.8V to +15V
Enable Input Voltage (VEN) .................................................................................................................................0V to VIN
† Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
‡ Notice: The device is not guaranteed to function outside its operating ratings.
Note 1: The maximum allowable power dissipation at any TA (ambient temperature) is PD(max) = (TJ(max) – TA) / θJA
.
Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regula-
tor will go into thermal shutdown. The θJA of the SOT-23-5 (M5) is 235°C/W soldered on a PC board (see
“Thermal Considerations” for further details).
2017 Microchip Technology Inc.
DS20005719A-page 3
MIC5207
TABLE 1-1:
ELECTRICAL CHARACTERISTICS (Note 1)
Electrical Characteristics: VIN = VOUT + 1V; IL = 100 μA; CL = 1.0 μF; VEN ≥ 2.0V; TJ = +25°C, bold values indicate
–40°C ≤ TJ ≤ +125°C except 0°C < TJ < +125°C for 1.8V; unless noted.
Parameter
Symbol
Min.
Typ.
Max.
Units
Conditions
–3
–4
—
—
3
4
Output Voltage Accuracy
VO
%
Variation from nominal VOUT
Output Voltage
Temperature Coefficient
∆VO/∆T
∆VO/VO
—
40
—
ppm/°C Note 2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.005
—
0.05
0.10
0.5
Line Regulation
Load Regulation
%
%
VIN = VOUT + 1V to 16V
0.05
—
∆VO/VO
VIN – VO
IGND
IL = 0.1 mA to 150 mA, Note 3
IL = 100 µA
0.7
17
60
—
80
115
—
175
250
280
325
300
400
1
IL = 50 mA
Dropout Voltage, Note 4
Quiescent Current
mV
µA
µA
140
—
IL = 100 mA
165
—
IL = 150 mA
0.01
—
VEN ≤ 0.4V (shutdown)
5
VEN ≤ 0.18V (shutdown)
80
130
170
650
900
1100
2000
2500
3000
—
VEN ≥ 2.0V, IL = 100 µA
IL = 50 mA
—
350
—
Ground Pin Current
(Note 5)
IGND
720
—
IL = 100 mA
1800
—
IL = 150 mA
Ripple Rejection
Current Limit
PSRR
ILIMIT
75
dB
mA
%/W
µV
—
320
0.05
100
500
—
VOUT = 0V
Note 6
—
Thermal Regulation
Output Noise
∆VO/∆PD
en
—
DS20005719A-page 4
2017 Microchip Technology Inc.
MIC5207
TABLE 1-1:
ELECTRICAL CHARACTERISTICS (Note 1) (CONTINUED)
Electrical Characteristics: VIN = VOUT + 1V; IL = 100 μA; CL = 1.0 μF; VEN ≥ 2.0V; TJ = +25°C, bold values indicate
–40°C ≤ TJ ≤ +125°C except 0°C < TJ < +125°C for 1.8V; unless noted.
Parameter
Enable Input
Symbol
Min.
Typ.
Max.
Units
Conditions
—
—
—
—
0.4
Enable Input Logic-Low
Voltage
VIL
VIH
IIL
V
V
Regulator shutdown
0.18
Enable Input Logic-High
Voltage
2.0
—
—
Regulator enable
—
—
—
—
0.01
—
–1
–2
20
25
VIL ≤ 0.4V
V
IL ≤ 0.18V
VIH ≥ 2.0V
VIH ≥ 2.0V
Enable Input Current
µA
5
IIH
—
Note 1: Specification for packaged product only.
2: Output voltage temperature coefficient is defined as the worst-case voltage change divided by the total
temperature range.
3: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are
tested for load regulation in the load range from 0.1 mA to 180 mA. Changes in output voltage due to heat-
ing effects are covered by the thermal regulation specification.
4: Dropout Voltage is defined as the input to output differential at which the output voltage drops 2% below its
nominal value measured at 1V differential.
5: Ground pin current is the regulator quiescent current plus pass transistor base current. The total current
drawn from the supply is the sum of the load current plus the ground pin current.
6: Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipa-
tion is applied, excluding load or line regulation effects. Specifications are for a 180 mA load pulse at VIN
16V for t = 10 ms.
=
2017 Microchip Technology Inc.
DS20005719A-page 5
MIC5207
TEMPERATURE SPECIFICATIONS (Note 1)
Parameters
Temperature Ranges
Sym.
Min.
Typ.
Max.
Units
Conditions
Storage Temperature Range
Lead Temperature
TS
—
TJ
–65
—
—
—
—
+150
+260
+125
°C
°C
°C
—
Soldering, 5 sec.
All, except 1.8V
Junction Temperature
–40
(2.5 ≤ VOUT ≤ 15V)
Junction Temperature
TJ
0
—
+125
°C
1.8V only
(1.8V ≤ VOUT < 2.5V)
Package Thermal Resistance
θJA
θJC
—
—
235
130
—
—
—
—
Thermal Resistance SOT-23
°C/W
Note 1: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., TA, TJ, JA). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability.
DS20005719A-page 6
2017 Microchip Technology Inc.
MIC5207
2.0
TYPICAL PERFORMANCE CURVES
Note: The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
0
-20
0
-20
VIN = 6V
OUT = 5V
VIN = 6V
VOUT = 5V
V
-40
-40
-60
-60
-80
-80
IOUT = 100μA
OUT = 1μF
IOUT = 1mA
COUT = 1μF
C
-100
-100
1E+11E+21E1+k31E+41E+51E+6 E+7
1E+11E+21E1+k31E+41E+51E+6 E+7
10k 1M 10M
100k
10k
1M 10M
10 100
100k
10 100
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 2-4:
Ratio.
Power Supply Rejection
FIGURE 2-1:
Ratio.
Power Supply Rejection
0
0
VIN = 6V
OUT = 5V
VIN = 6V
OUT = 5V
V
V
-20
-20
-40
-60
-40
-60
IOUT = 1mA
IOUT = 100μA
-80
C
C
OUT = 2.2μF
BYP = 0.01μF
-80
C
C
OUT = 2.2μF
BYP = 0.01μF
-100
-100
1E+11E+21E1+k31E+41E+51E+6 E+7
10k
1M 10M
100k
10 100
1E+11E+21E1+k31E+41E+51E+6 E+7
10k
1M 10M
100k
10 100
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 2-5:
Ratio.
Power Supply Rejection
FIGURE 2-2:
Ratio.
Power Supply Rejection
100
60
90
80
70
60
50
40
30
20
10
0
50
40
30
20
10
0
1mA
1mA
IOUT = 100mA
COUT = 2.2μF
10mA
IOUT = 100mA
COUT = 1μF
10mA
CBYP = 0.01μF
0
0.1
0.2
0.3 0.4
0
0.1
0.2
0.3
0.4
VOLTAGE DROP (V)
VOLTAGE DROP (V)
FIGURE 2-6:
Rejection vs. Voltage Drop.
Power Supply Ripple
FIGURE 2-3:
Rejection vs. Voltage Drop.
Power Supply Ripple
2017 Microchip Technology Inc.
DS20005719A-page 7
MIC5207
0
-20
0
VIN = 6V
OUT = 5V
VIN = 6V
VOUT = 5V
V
-20
-40
-40
-60
-60
IOUT = 100mA
OUT = 1μF
-80
-80
IOUT = 10mA
OUT = 1μF
C
C
-100
-100
1E+11E+21E+31E+41E+51E+6 E+7
1E+11E+21E1+k311E0+k41E+51E1M+6 E+7
1k
10k
10 100
100k
10M
10
100k
1M 10M
100
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 2-10:
Ratio.
Power Supply Rejection
FIGURE 2-7:
Ratio.
Power Supply Rejection
0
-20
0
VIN = 6V
OUT = 5V
VIN = 6V
OUT = 5V
V
V
-20
-40
-40
-60
-60
IOUT = 100mA
IOUT = 10mA
-80
-80
C
C
OUT = 2.2μF
BYP = 0.01μF
C
C
OUT = 2.2μF
BYP = 0.01μF
-100
-100
1E+11E+21E+31E+41E+51E+6 E+7
1k 10k
1M
10M
10 100
100k
FREQUENCY (Hz)
1E+11E+21E1+k311E0+k41E+51E1M+6 E+7
10 100
100k
10M
FREQUENCY (Hz)
FIGURE 2-11:
Ratio.
Power Supply Rejection
FIGURE 2-8:
Ratio.
Power Supply Rejection
320
280
240
200
160
120
80
10000
+125°C
+25°C
1000
100
10
–40°C
40
0
0
40
80
120
160
10
100
1000
10000
OUTPUT CURRENT (mA)
CAPACITANCE (pF)
FIGURE 2-12:
Current.
Dropout Voltage vs. Output
FIGURE 2-9:
Capacitance.
Turn-On Time vs. Bypass
DS20005719A-page 8
2017 Microchip Technology Inc.
MIC5207
10
1
10
1
10mA, COUT = 1μF
100mA
0.1
0.1
1mA
OUT = 1μF
C
C
BYP = 10nF
0.01
0.001
0.0001
0.01
0.001
0.0001
1mA
10mA
VOUT = 5V
OUT = 10μF
electrolytic
BYP = 100pF
C
C
VOUT = 5V
1E1+011E+21E+31E+41E+51E+61E+7
1E10+11E+21E1k+31E+41E+51E1M+61E+7
100
10k 100k 10M
1k
100
10k 100k 1M 10M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 2-16:
Noise Performance.
FIGURE 2-13:
Noise Performance.
10
10
1
0.1
1
0.1
100mA
10mA
10mA
100mA
0.01
0.01
1mA
VOUT = 5V
OUT = 10μF
electrolytic
BYP = 1nF
C
VOUT = 5V
OUT = 10μF
electrolytic
1mA
0.001
0.001
C
C
0.0001
0.0001
1E10+11E+21E1k+31E+41E+51E1M+61E+7
100
10k 100k
FREQUENCY (Hz)
10M
1E10+11E+21E1k+31E+41E+51E1M+61E+7
100
10k 100k
10M
FREQUENCY (Hz)
FIGURE 2-17:
Noise Performance.
FIGURE 2-14:
Noise Performance.
10
10
1
0.1
1
0.1
100mA
1mA
10mA
100mA
0.01
0.01
VOUT = 5V
VOUT = 5V
C
OUT = 10μF
C
OUT = 22μF
10mA
1mA
0.001
0.001
electrolytic
C
tantalum
C
BYP = 10nF
BYP = 10nF
0.0001
0.0001
1E1+011E+21E+31E+41E+51E+61E+7
100 1k 10k 100k
10M
1M
1E10+11E+21E1k+31E+41E+51E1M+61E+7
100
10k 100k
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 2-18:
Noise Performance.
FIGURE 2-15:
Noise Performance.
2017 Microchip Technology Inc.
DS20005719A-page 9
MIC5207
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE
Pin Number Pin Name
Description
1
2
3
IN
GND
EN
Supply input.
Ground.
Enable/Shutdown (Input): CMOS-compatible input. Logic-high = enable, logic-low =
shutdown. Do not leave floating.
4 (Fixed)
BYP
Reference Bypass: Connect external 470 pF capacitor to GND to reduce output noise.
May be left open. For 1.8V or 2.5V operation, see Applications Information section.
4 (Adj.)
5
ADJ
Adjust (Input): Adjustable regulator feedback input. Connect to resistor voltage divider.
Regulator output.
OUT
DS20005719A-page 10
2017 Microchip Technology Inc.
MIC5207
At lower values of output current, less output
capacitance is required for output stability. The
capacitor can be reduced to 0.47 µF for current below
10 mA or 0.33 µF for currents below 1 mA.
4.0
4.1
APPLICATIONS INFORMATION
Enable/Shutdown
Forcing EN (enable/shutdown) high (> 2V) enables the
regulator. EN is compatible with CMOS logic gates.
4.5
No-Load Stability
If the enable/shutdown feature is not required, connect
EN (pin 3) to IN (supply input, pin 1). See Figure 4-1.
The MIC5207 will remain stable and in regulation with
no load (other than the internal voltage divider) unlike
many other voltage regulators. This is especially
important in CMOSRAM keep-alive applications.
4.2
Input Capacitor
A 1 µF capacitor should be placed from IN to GND if
there is more than 10 inches of wire between the input
and the AC filter capacitor or if a battery is used as the
input.
4.6
Thermal Considerations
The MIC5207 is designed to provide 180 mA of
continuous current in a very small package. Maximum
power dissipation can be calculated based on the
output current and the voltage drop across the part. To
determine the maximum power dissipation of the
package, use the junction-to-ambient thermal
resistance of the device and the following basic
equation shown in Equation 4-1:
4.3
Reference Bypass Capacitor
Reference bypass (BYP) is connected to the internal
voltage reference. 470 pF capacitor (CBYP
A
)
connected from BYP to GND quiets this reference,
providing a significant reduction in output noise. CBYP
reduces the regulator phase margin; when using CBYP
output capacitors of 2.2 µF or greater are generally
required to maintain stability.
,
EQUATION 4-1:
The start-up speed of the MIC5207 is inversely
proportional to the size of the reference bypass
capacitor. Applications requiring a slow ramp-up of
TJMAX – TA
PDMAX = ------------------------------------
JA
output voltage should consider larger values of CBYP
Likewise, if rapid turn-on is necessary, consider
omitting CBYP
.
.
TJ(MAX) is the maximum junction temperature of the
die, +125°C, and TA is the ambient operating
temperature. θJA is layout dependent; Table 4-1 shows
examples of junction-to-ambient thermal resistance for
the MIC5207.
If output noise is not a major concern, omit CBYP and
leave BYP open.
4.4
Output Capacitor
An output capacitor is required between OUT and GND
to prevent oscillation. The minimum size of the output
capacitor is dependent upon whether a reference
bypass capacitor is used. 1.0 µF minimum is
recommended when CBYP is not used (see Figure 4-2).
2.2 µF minimum is recommended when CBYP is 470 pF
(see Figure 4-1). Larger values improve the regulator’s
transient response. The output capacitor value may be
increased without limit.
TABLE 4-1:
SOT-23-5 THERMAL
RESISTANCE
θJA Rec.
Min. Footprint Copper Clad
θJA 1” Square
θJ/C
235°C/W 170°C/W
The actual power dissipation of the regulator circuit can
be determined using Equation 4-2:
130°C/W
EQUATION 4-2:
The output capacitor should have an ESR (effective
series resistance) of about 5Ω or less and a resonant
frequency above 1 MHz. Ultra-low-ESR (ceramic)
capacitors can cause a low amplitude oscillation on the
output and/or under-damped transient response. Most
tantalum or aluminum electrolytic capacitors are
adequate; film types will work, but are more expensive.
Since many aluminum electrolytics have electrolytes
that freeze at about –30°C, solid tantalums are
recommended for operation below –25°C.
PD = VIN – VOUT IOUT + VIN IGND
Substituting PD(MAX) for PD and solving for the
operating conditions that are critical to the application
will give the maximum operating conditions for the
regulator circuit. For example, when operating the
2017 Microchip Technology Inc.
DS20005719A-page 11
MIC5207
MIC5207-3.3YM5 at room temperature with a minimum
footprint layout, the maximum input voltage for a set
output current can be determined with Equation 4-3:
Therefore, a 3.3V application at 150 mA of output
current can accept a maximum input voltage of 6V in a
SOT-23-5 package. For a full discussion of heat sinking
and thermal effects on voltage regulators, refer to the
Regulator Thermals section of Microchip’s Designing
with Low-Dropout Voltage Regulators handbook.
EQUATION 4-3:
125oC – 25oC
235oC/W
4.7
Low-Voltage Operation
PDMAX = ---------------------------------- = 4 2 5 mW
The MIC5207-1.8 and MIC5207-2.5 require special
consideration when used in voltage-sensitive systems.
They may momentarily overshoot their nominal output
voltages unless appropriate output and bypass
capacitor values are chosen.
The junction-to-ambient thermal resistance for the
minimum footprint is 235°C/W, from Table 4-1. The
maximum power dissipation must not be exceeded for
proper operation. Using the output voltage of 3.3V and
an output current of 150 mA, the maximum input
voltage can be determined. From Table 1-1, the
maximum ground current for 150 mA output current is
3000 µA or 3 mA.
During regulator power up, the pass transistor is fully
saturated for a short time, while the error amplifier and
voltage reference are being powered up more slowly
from the output (see Functional Diagrams). Selecting
larger output and bypass capacitors allows additional
time for the error amplifier and reference to turn on and
prevent overshoot.
EQUATION 4-4:
To ensure that no overshoot is present when starting up
into a light load (100 µA), use a 4.7 µF output
capacitance and 470 pF bypass capacitance. This
slows the turn-on enough to allow the regulator to react
and keep the output voltage from exceeding its nominal
425mW = VIN – 3.3V 150mA + VIN 3mA
value. At heavier loads, use
a 10 µF output
capacitance and 470 pF bypass capacitance. Lower
values of output and bypass capacitance can be used,
depending on the sensitivity of the system.
Where:
Applications that can withstand some overshoot on the
output of the regulator can reduce the output capacitor
and/or reduce or eliminate the bypass capacitor.
Applications that are not sensitive to overshoot due to
power-on reset delays can use normal output and
bypass capacitor configurations.
EQUATION 4-5:
425mW = VIN 150mA – 495mW + VIN 3mA
Please note the junction temperature range of the
regulator with an output less than 2.5V fixed and
adjustable is 0°C to +125°C.
Then:
4.8
Fixed Regulator Applications
EQUATION 4-6:
MIC5207-x.xYM5
920mW = VIN 153mA
VIN
VOUT
2.2μF
470pF
1
2
3
5
4
Resulting in:
EQUATION 4-7:
FIGURE 4-1:
Ultra-Low-Noise
Fixed-Voltage Application.
VINMAX = 6.01V
DS20005719A-page 12
2017 Microchip Technology Inc.
MIC5207
Figure 4-1 includes
a
470 pF capacitor for
Figure 4-3 includes the optional 470 pF noise bypass
capacitor from ADJ to GND to reduce output noise.
ultra-low-noise operation and shows EN (pin 3)
connected to IN (pin 1) for an application where
enable/shutdown is not required. COUT = 2.2 µF
minimum.
4.10 Dual-Supply Operation
When used in dual-supply systems where the regulator
load is returned to a negative supply, the output voltage
must be diode clamped to ground.
MIC5207-x.xYM5
VIN
VOUT
1.0μF
1
2
3
5
4.11 USB Application
EN
Figure 4-4 shows the MIC5207-3.3YM5 in a USB
application. Because the VBUS supply may be greater
than 10 inches from the regulator, a 1 µF input
capacitor is included.
4
ENABLE
SHUTDOWN
FIGURE 4-2:
Low-Noise Fixed-Voltage
Application.
VCC
5.0V
UPSTREAM
VBUS
100mA MAX.
VBUS
10K
Figure 4-2 is an example of a basic low-noise
configuration. COUT = 1 µF minimum.
FERRITE
BEADS
USB CONTROLLER
MIC2525
MIC5207-3.3YM5
VIN
VOUT
1μF
VBUS
1
2
3
5
ON/OFF
OVERCURRENT
EN
FLG
OUT
IN
D+
D+
D–
USB
PORT
D–
GND
4
GND
OUT
IN
1μF
150μF
GND
4.9
Adjustable Regulator Applications
0.1μF
DATA
DATA
The MIC5207YM5 can be adjusted to a specific output
voltage by using two external resistors (Figure 4-3).
The resistors set the output voltage based on
Equation 4-8:
FIGURE 4-4:
Single-Port Self-Powered
Hub.
EQUATION 4-8:
R2
R1
VOUT = VREF 1 + ------ = 1.242V
This equation is correct due to the configuration of the
bandgap reference. The bandgap voltage is relative to
the output, as seen in the Functional Diagrams.
Traditional regulators normally have the reference
voltage relative to ground; therefore, their equations
are different from the equation for the MIC5207YM5.
Resistor values are not critical because ADJ (adjust)
has a high input impedance, but for best results use
resistors of 470 kΩ or less. A capacitor from ADJ to
ground provides greatly improved noise performance.
MIC5207YM5
VIN
VOUT
2.2μF
1
2
3
5
R1
R2
4
470pF
FIGURE 4-3:
Ultra-Low-Noise
Adjustable-Voltage Application.
2017 Microchip Technology Inc.
DS20005719A-page 13
MIC5207
5.0
5.1
PACKAGING INFORMATION
Package Marking Information
5-Pin SOT-23*
Example
XXXX
NNN
LE50
943
5-Pin TSOT*
Example
XXXX
NNN
NA18
235
Legend: XX...X Product code or customer-specific information
Y
Year code (last digit of calendar year)
YY
WW
NNN
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
e
3
*
)
e
3
●, ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle
mark).
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information. Package may or may not include
the corporate logo.
Underbar (_) and/or Overbar (⎯) symbol may not be to scale.
DS20005719A-page 14
2017 Microchip Technology Inc.
MIC5207
5-Lead SOT-23 Package Outline and Recommended Land Pattern
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging.
2017 Microchip Technology Inc.
DS20005719A-page 15
MIC5207
5-Lead TSOT Package Outline and Recommended Land Pattern
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging.
DS20005719A-page 16
2017 Microchip Technology Inc.
MIC5207
APPENDIX A: REVISION HISTORY
Revision A (February 2017)
• Converted Micrel document MIC5207 to Micro-
chip data sheet DS20005719A.
• Minor text changes throughout.
• Removed all reference to discontinued leaded
parts.
• Added θJC value for SOT-23 package in Tempera-
ture Specifications section.
2017 Microchip Technology Inc.
DS20005719A-page 17
MIC5207
NOTES:
DS20005719A-page 18
2017 Microchip Technology Inc.
MIC5207
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office.
Examples:
–
PART NO.
Device
–
X
X
XX
X.X
a) MIC5207-1.8YD5-TR: 180 mA Low-Noise LDO
Regulator, 1.8V Voltage, 5-Lead
TSOT, –40°C to +125°C
Media Type
Temperature Package
Voltage
Temperature Range,
3,000/Reel
Device:
MIC5207:
180 mA Low Noise LDO Regulator
b) MIC5207-2.5YM5-TR: 180 mA Low-Noise LDO
Regulator, 2.5V Voltage, 5-Lead
SOT-23, –40°C to +125°C
Voltage:
(blank) = Adjustable
1.8
2.5
2.8
2.9
3.0
3.1
3.2
3.3
4.0
5.0
=
=
=
=
=
=
=
=
=
=
1.8V
2.5V
2.8V
2.9V
3.0V
3.1V
3.2V
3.3V
4.0V
5.0V
Temperature Range,
3,000/Reel
c) MIC5207-2.5YM5-TX: 180 mA Low-Noise LDO
Regulator, 2.5V Voltage, 5-Lead
SOT-23, –40°C to +125°C
Temperature Range,
3,000/Reel (Reverse Pin 1)
d) MIC5207YM5-TR:
180 mA Low-Noise LDO
Regulator, Adj. Voltage, 5-Lead
SOT-23, –40°C to +125°C
Temperature Range,
3,000/Reel
Temperature:
Package:
Y
=
–40°C to +125°C
D5
M5
=
=
5-Lead TSOT
5-Lead SOT-23
e) MIC5207-2.9YM5-TR: 180 mA Low-Noise LDO
Regulator, 2.9V Voltage, 5-Lead
SOT-23, –40°C to +125°C
Media Type:
TR
TX
=
=
3,000/Reel
3,000/Reel (Reverse Pin 1 Orientation)
Temperature Range,
3,000/Reel
f) MIC5207-3.1YM5-TR: 180 mA Low-Noise LDO
Regulator, 3.1V Voltage, 5-Lead
SOT-23, –40°C to +125°C
Temperature Range,
3,000/Reel
g) MIC5207-5.0YM5-TR: 180 mA Low-Noise LDO
Regulator, 5.0V Voltage, 5-Lead
SOT-23, –40°C to +125°C
Temperature Range,
3,000/Reel
h) MIC5207-3.3YM5-TX: 180 mA Low-Noise LDO
Regulator, 3.3V Voltage, 5-Lead
SOT-23, –40°C to +125°C
Temperature Range,
3,000/Reel (Reverse Pin 1)
Note 1:
Tape and Reel identifier only appears in the
catalog part number description. This identifier is
used for ordering purposes and is not printed on
the device package. Check with your Microchip
Sales Office for package availability with the
Tape and Reel option.
2017 Microchip Technology Inc.
DS20005719A-page 19
MIC5207
NOTES:
DS20005719A-page 20
2017 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, AnyRate, AVR,
AVR logo, AVR Freaks, BeaconThings, BitCloud, CryptoMemory,
CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KEELOQ,
KEELOQ logo, Kleer, LANCheck, LINK MD, maXStylus,
maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB,
OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip
Designer, QTouch, RightTouch, SAM-BA, SpyNIC, SST, SST
Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
and other countries.
ClockWorks, The Embedded Control Solutions Company,
EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS,
mTouch, Precision Edge, and Quiet-Wire are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo,
CodeGuard, CryptoAuthentication, CryptoCompanion,
CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average
Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial
Programming, ICSP, Inter-Chip Connectivity, JitterBlocker,
KleerNet, KleerNet logo, Mindi, MiWi, motorBench, MPASM, MPF,
MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, PureSilicon, QMatrix, RightTouch logo, REAL ICE, Ripple
Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI,
SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC,
USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and
ZENA are trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
Silicon Storage Technology is a registered trademark of Microchip
Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip Technology
Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
QUALITYꢀMANAGEMENTꢀꢀSYSTEMꢀ
CERTIFIEDꢀBYꢀDNVꢀ
© 2017, Microchip Technology Incorporated, All Rights Reserved.
ISBN: 978-1-5224-1408-7
== ISO/TSꢀ16949ꢀ==ꢀ
2017 Microchip Technology Inc.
DS20005719A-page 21
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Asia Pacific Office
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
Finland - Espoo
Tel: 358-9-4520-820
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Web Address:
www.microchip.com
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
France - Saint Cloud
Tel: 33-1-30-60-70-00
India - Pune
Tel: 91-20-3019-1500
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Austin, TX
Tel: 512-257-3370
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Boston
Tel: 49-2129-3766400
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
Germany - Heilbronn
Tel: 49-7131-67-3636
China - Dongguan
Tel: 86-769-8702-9880
Germany - Karlsruhe
Tel: 49-721-625370
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Guangzhou
Tel: 86-20-8755-8029
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
Korea - Seoul
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Germany - Rosenheim
Tel: 49-8031-354-560
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Israel - Ra’anana
Tel: 972-9-744-7705
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Detroit
Novi, MI
Tel: 248-848-4000
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Houston, TX
Tel: 281-894-5983
Italy - Padova
Tel: 39-049-7625286
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
China - Shanghai
Tel: 86-21-3326-8000
Fax: 86-21-3326-8021
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Norway - Trondheim
Tel: 47-7289-7561
Los Angeles
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Poland - Warsaw
Tel: 48-22-3325737
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Romania - Bucharest
Tel: 40-21-407-87-50
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Raleigh, NC
Tel: 919-844-7510
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
New York, NY
Tel: 631-435-6000
Sweden - Gothenberg
Tel: 46-31-704-60-40
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Sweden - Stockholm
Tel: 46-8-5090-4654
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
DS20005719A-page 22
2017 Microchip Technology Inc.
11/07/16
相关型号:
MIC5207-3.3YZ
Fixed Positive LDO Regulator, 3.3V, 0.4V Dropout, BIPolar, PBCY3, LEAD FREE, TO-92, 3 PIN
MICROCHIP
MIC5207-3.3YZ
3.3V FIXED POSITIVE LDO REGULATOR, 0.4V DROPOUT, PBCY3, LEAD FREE, TO-92, 3 PIN
ROCHESTER
MIC5207-3.6BM5
Fixed Positive LDO Regulator, 3.6V, 0.4V Dropout, BIPolar, PDSO5, SOT-23, 5 PIN
MICROCHIP
MIC5207-3.6BM5T&R
Fixed Positive LDO Regulator, 3.6V, 0.4V Dropout, BIPolar, PDSO5, SOT-23, 5 PIN
MICROCHIP
©2020 ICPDF网 联系我们和版权申明