PIC16C64A-20I/P [MICROCHIP]
8-Bit CMOS Microcontrollers; 8位CMOS微控制器型号: | PIC16C64A-20I/P |
厂家: | MICROCHIP |
描述: | 8-Bit CMOS Microcontrollers |
文件: | 总336页 (文件大小:2583K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PIC16C6X
8-Bit CMOS Microcontrollers
• Low-power, high-speed CMOS EPROM/ROM
technology
• Fully static design
• Wide operating voltage range: 2.5V to 6.0V
• Commercial, Industrial, and Extended
temperature ranges
• Low-power consumption:
• < 2 mA @ 5V, 4 MHz
Devices included in this data sheet:
• PIC16C61
• PIC16C62
• PIC16C62A
• PIC16CR62
• PIC16C63
• PIC16CR63
• PIC16C64
• PIC16C64A
• PIC16CR64
• PIC16C65
• PIC16C65A
• PIC16CR65
• PIC16C66
• PIC16C67
• 15 µA typical @ 3V, 32 kHz
• < 1 µA typical standby current
PIC16C6X Microcontroller Core Features:
PIC16C6X Peripheral Features:
• High performance RISC CPU
• Only 35 single word instructions to learn
• All single cycle instructions except for program
branches which are two-cycle
• Timer0: 8-bit timer/counter with 8-bit prescaler
• Timer1: 16-bit timer/counter with prescaler,
can be incremented during sleep via
external crystal/clock
• Timer2: 8-bit timer/counter with 8-bit period
register, prescaler and postscaler
• Operating speed: DC - 20 MHz clock input
DC - 200 ns instruction cycle
• Capture/Compare/PWM (CCP) module(s)
• Capture is 16-bit, max resolution is 12.5 ns,
Compare is 16-bit, max resolution is 200 ns,
PWM max resolution is 10-bit.
• Synchronous Serial Port (SSP) with SPI and I C
• Universal Synchronous Asynchronous Receiver
Transmitter (USART/SCI)
• Parallel Slave Port (PSP) 8-bits wide, with
external RD, WR and CS controls
• Brown-out detection circuitry for
Brown-out Reset (BOR)
• Interrupt capability
• Eight level deep hardware stack
• Direct, indirect, and relative addressing modes
• Power-on Reset (POR)
• Power-up Timer (PWRT) and
Oscillator Start-up Timer (OST)
• Watchdog Timer (WDT) with its own on-chip RC
oscillator for reliable operation
• Programmable code-protection
• Power saving SLEEP mode
2
• Selectable oscillator options
PIC16C6X Features
61
62 62A R62
63
R63
64 64A R64
65
65A
R65
66
67
Program Memory
(EPROM) x 14
1K
2K
2K
—
4K
—
2K
2K
—
4K
4K
—
8K
8K
(ROM) x 14
—
—
—
2K
—
192
22
—
4K
192
22
—
—
—
2K
—
192
33
—
192
33
4K
192
33
—
368
22
—
—
368
33
Data Memory (Bytes) x 8
I/O Pins
36 128 128 128
128 128 128
33 33 33
Yes Yes Yes
13
—
—
22
—
1
22
—
1
22
—
1
Parallel Slave Port
Yes
2
Yes
2
Yes
2
Yes
2
Capture/Compare/PWM
Module(s)
2
2
1
1
1
2
Timer Modules
1
3
3
3
3
3
3
3
3
3
3
3
3
3
—
SPI/ SPI/ SPI/ SPI/I2C, SPI/I2C, SPI/ SPI/ SPI/ SPI/I2C, SPI/I2C, SPI/I2C, SPI/I2C, SPI/I2C,
Serial Communication
I2C I2C I2C USART USART I2C I2C I2C USART USART USART USART USART
In-Circuit Serial
Programming
Yes Yes Yes Yes
Yes
Yes
Yes Yes Yes
Yes
Yes
Yes
Yes
Yes
Brown-out Reset
Interrupt Sources
—
3
—
7
Yes Yes
Yes
10
Yes
10
—
8
Yes Yes
—
Yes
11
Yes
11
Yes
10
Yes
11
7
7
8
8
11
Sink/Source Current (mA) 25/20 25/25 25/25 25/25 25/25 25/25 25/25 25/25 25/25 25/25 25/25 25/25 25/25 25/25
1997 Microchip Technology Inc.
DS30234D-page 1
PIC16C6X
Pin Diagrams
PDIP, SOIC, Windowed CERDIP
SDIP, SOIC, SSOP, Windowed CERDIP (300 mil)
RA1
18
17
16
15
14
13
12
11
10
MCLR/VPP
RA0
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0/INT
VDD
RA2
RA3
1
2
3
4
5
6
7
8
9
1
28
27
26
25
24
23
22
21
20
19
18
17
16
15
2
RA0
RA1
3
RA4/T0CKI
MCLR/VPP
OSC1/CLKIN
RA2
4
OSC2/CLKOUT
VDD
RA3
5
RA4/T0CKI
RA5/SS
VSS
6
VSS
RB0/INT
RB1
7
RB7
RB6
RB5
RB4
8
OSC1/CLKIN
9
RB2
VSS
OSC2/CLKOUT
10
11
12
13
14
RB3
RC7
RC0/T1OSI/T1CKI
RC1/T1OSO
RC6
RC2/CCP1
RC5/SDO
RC4/SDI/SDA
PIC16C61
RC3/SCK/SCL
PIC16C62
SDIP, SOIC, SSOP, Windowed CERDIP (300 mil) SDIP, SOIC, Windowed CERDIP (300 mil)
1
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1
28
27
26
25
24
23
22
21
20
19
18
17
16
15
RB7
MCLR/VPP
RA0
MCLR/VPP
RA0
RB7
RB6
2
2
RB6
3
3
RA1
RA1
RB5
RB5
4
4
RA2
RA2
RB4
RB4
5
5
RA3
RA4/T0CKI
RA5/SS
RB3
RA3
RA4/T0CKI
RA5/SS
RB3
6
6
RB2
RB2
7
7
RB1
RB1
8
8
VSS
RB0/INT
VDD
VSS
RB0/INT
VDD
OSC1/CLKIN
9
OSC1/CLKIN
9
10
11
12
13
14
10
11
12
13
14
VSS
VSS
OSC2/CLKOUT
RC0/T1OSO/T1CKI
RC1/T1OSI
OSC2/CLKOUT
RC0/T1OSO/T1CKI
RC1/T1OSI/CCP2
RC2/CCP1
RC7
RC7/RX/DT
RC6/TX/CK
RC5/SDO
RC4/SDI/SDA
RC6
RC2/CCP1
RC5/SDO
RC4/SDI/SDA
RC3/SCK/SCL
RC3/SCK/SCL
PIC16C62A
PIC16CR62
PIC16C63
PIC16CR63
PIC16C66
PDIP, Windowed CERDIP
MCLR/VPP
RA0
1
2
3
4
5
6
7
8
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0/INT
VDD
VSS
RD7/PSP7
RD6/PSP6
RD5/PSP5
RD4/PSP4
RC7
MCLR/VPP
RA0
1
2
3
4
5
6
7
8
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0/INT
VDD
MCLR/VPP
RA0
1
2
3
4
5
6
7
8
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RA1
RA2
RA3
RA1
RA2
RA3
RA1
RA2
RA3
RA4/T0CKI
RA5/SS
RE0/RD
RA4/T0CKI
RA5/SS
RE0/RD
RE1/WR
RE2/CS
VDD
RA4/T0CKI
RA5/SS
RE0/RD
RE1/WR
RE2/CS
VDD
RB0/INT
RE1/WR
RE2/CS
VDD
9
9
9
VDD
VSS
10
11
12
13
14
15
16
17
18
19
20
10
11
12
13
14
15
16
17
18
19
20
VSS
10
11
12
13
14
15
16
17
18
19
20
RD7/PSP7
RD6/PSP6
RD5/PSP5
RD4/PSP4
RC7
RC6
RC5/SDO
RC4/SDI/SDA
RD3/PSP3
RD2/PSP2
RD7/PSP7
RD6/PSP6
RD5/PSP5
RD4/PSP4
RC7/RX/DT
RC6/TX/CK
RC5/SDO
RC4/SDI/SDA
RD3/PSP3
RD2/PSP2
VSS
VSS
OSC1/CLKIN
OSC2/CLKOUT
RC0/T1OSO/T1CKI
RC1/T1OSI
VSS
OSC1/CLKIN
OSC2/CLKOUT
RC0/T1OSI/T1CKI
RC1/T1OSO
RC2/CCP1
RC3/SCK/SCL
RD0/PSP0
OSC1/CLKIN
OSC2/CLKOUT
RC0/T1OSO/T1CKI
RC1/T1OSI/CCP2
RC2/CCP1
RC6
RC5/SDO
RC4/SDI/SDA
RD3/PSP3
RD2/PSP2
RC2/CCP1
RC3/SCK/SCL
RD0/PSP0
RC3/SCK/SCL
RD0/PSP0
RD1/PSP1
RD1/PSP1
RD1/PSP1
PIC16C64A
PIC16CR64
PIC16C64
PIC16C65
PIC16C65A
PIC16CR65
PIC16C67
DS30234D-page 2
1997 Microchip Technology Inc.
PIC16C6X
Pin Diagrams (Cont.’d)
MQFP
PLCC
RA4/T0CKI
RA5/SS
RE0/RD
RE1/WR
RE2/CS
RB3
RB2
RB1
RB0/INT
VDD
7
8
9
39
38
37
36
35
34
33
32
31
30
29
NC
RC7
RD4/PSP4
RD5/PSP5
RD6/PSP6
RD7/PSP7
VSS
VDD
RB0/INT
RB1
1
2
3
4
5
6
7
8
33
32
31
30
29
28
27
26
25
24
23
RC0/T1OSI/T1CKI
OSC2/CLKOUT
OSC1/CLKIN
VSS
VDD
RE2/CS
RE1/WR
RE0/RD
RA5/SS
RA4/T0CKI
10
11
12
13
14
15
16
17
VDD
VSS
VSS
PIC16C64
PIC16C64
RD7/PSP7
RD6/PSP6
RD5/PSP5
RD4/PSP4
RC7
OSC1/CLKIN
OSC2/CLKOUT
RC0/T1OSI/T1CKI
NC
9
10
11
RB2
RB3
MQFP,
TQFP (PIC16C64A only)
PLCC
RA4/T0CKI
RA5/SS
RE0/RD
RE1/WR
RE2/CS
VDD
VSS
OSC1/CLKIN
OSC2/CLKOUT
RB3
RB2
RB1
RB0/INT
VDD
7
8
9
39
38
37
36
35
34
33
32
31
30
29
NC
RC7
RD4/PSP4
RD5/PSP5
RD6/PSP6
RD7/PSP7
VSS
VDD
RB0/INT
RB1
1
2
3
4
5
6
7
8
33
32
31
30
29
28
27
26
25
24
23
RC0/T1OSO/T1CKI
OSC2/CLKOUT
OSC1/CLKIN
VSS
VDD
RE2/CS
RE1/WR
RE0/RD
RA5/SS
RA4/T0CKI
10
11
12
13
14
15
16
17
VSS
PIC16C64A
PIC16CR64
RD7/PSP7
RD6/PSP6
RD5/PSP5
RD4/PSP4
RC7
PIC16C64A
PIC16CR64
RC0/T1OSO/T1CKI
NC
9
10
11
RB2
RB3
MQFP,
TQFP (Not on PIC16C65)
PLCC
RA4/T0CKI
RA5/SS
RE0/RD
RE1/WR
RE2/CS
VDD
VSS
OSC1/CLKIN
OSC2/CLKOUT
RB3
RB2
RB1
RB0/INT
VDD
7
8
9
39
38
37
36
35
34
33
32
31
30
29
NC
RC7/RX/DT
RD4/PSP4
RD5/PSP5
RD6/PSP6
RD7/PSP7
VSS
VDD
RB0/INT
RB1
1
2
3
4
5
6
7
8
33
32
31
30
29
28
27
26
25
24
23
RC0/T1OSO/T1CKI
OSC2/CLKOUT
OSC1/CLKIN
VSS
VDD
RE2/CS
RE1/WR
RE0/RD
RA5/SS
RA4/T0CKI
10
11
12
13
14
15
16
17
PIC16C65
PIC16C65A
PIC16CR65
PIC16C67
PIC16C65
PIC16C65A
PIC16CR65
PIC16C67
VSS
RD7/PSP7
RD6/PSP6
RD5/PSP5
RD4/PSP4
RC7/RX/DT
RC0/T1OSO/T1CKI
NC
9
10
11
RB2
RB3
1997 Microchip Technology Inc.
DS30234D-page 3
PIC16C6X
Table Of Contents
1.0 General Description ....................................................................................................................................................................... 5
2.0 PIC16C6X Device Varieties........................................................................................................................................................... 7
3.0 Architectural Overview................................................................................................................................................................... 9
4.0 Memory Organization................................................................................................................................................................... 19
5.0 I/O Ports....................................................................................................................................................................................... 51
6.0 Overview of Timer Modules ......................................................................................................................................................... 63
7.0 Timer0 Module............................................................................................................................................................................. 65
8.0 Timer1 Module............................................................................................................................................................................. 71
9.0 Timer2 Module............................................................................................................................................................................. 75
10.0 Capture/Compare/PWM (CCP) Module(s)................................................................................................................................... 77
11.0 Synchronous Serial Port (SSP) Module....................................................................................................................................... 83
12.0 Universal Synchronous Asynchronous Receiver Transmitter (USART) Module ....................................................................... 105
13.0 Special Features of the CPU ..................................................................................................................................................... 123
14.0 Instruction Set Summary............................................................................................................................................................ 143
15.0 Development Support ................................................................................................................................................................ 159
16.0 Electrical Characteristics for PIC16C61..................................................................................................................................... 163
17.0 DC and AC Characteristics Graphs and Tables for PIC16C61.................................................................................................. 173
18.0 Electrical Characteristics for PIC16C62/64................................................................................................................................ 183
19.0 Electrical Characteristics for PIC16C62A/R62/64A/R64............................................................................................................ 199
20.0 Electrical Characteristics for PIC16C65..................................................................................................................................... 215
21.0 Electrical Characteristics for PIC16C63/65A ............................................................................................................................. 231
22.0 Electrical Characteristics for PIC16CR63/R65........................................................................................................................... 247
23.0 Electrical Characteristics for PIC16C66/67................................................................................................................................ 263
24.0 DC and AC Characteristics Graphs and Tables for:
PIC16C62, PIC16C62A, PIC16CR62, PIC16C63, PIC16C64, PIC16C64A, PIC16CR64,
PIC16C65A, PIC16C66, PIC16C67........................................................................................................................................... 281
25.0 Packaging Information ............................................................................................................................................................... 291
Appendix A: Modifications.............................................................................................................................................................. 307
Appendix B: Compatibility .............................................................................................................................................................. 307
Appendix C: What’s New................................................................................................................................................................ 308
Appendix D: What’s Changed ........................................................................................................................................................ 308
Appendix E:
PIC16/17 Microcontrollers ....................................................................................................................................... 309
Pin Compatibility ................................................................................................................................................................................ 315
Index .................................................................................................................................................................................................. 317
List of Equation and Examples........................................................................................................................................................... 326
List of Figures..................................................................................................................................................................................... 326
List of Tables...................................................................................................................................................................................... 330
Reader Response .............................................................................................................................................................................. 334
PIC16C6X Product Identification System........................................................................................................................................... 335
For register and module descriptions in this data sheet, device legends show which devices apply to those sections. For
example, the legend below shows that some features of only the PIC16C62A, PIC16CR62, PIC16C63, PIC16C64A,
PIC16CR64, and PIC16C65A are described in this section.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
To Our Valued Customers
We constantly strive to improve the quality of all our products and documentation. We have spent an exceptional
amount of time to ensure that these documents are correct. However, we realize that we may have missed a few
things. If you find any information that is missing or appears in error, please use the reader response form in the
back of this data sheet to inform us. We appreciate your assistance in making this a better document.
DS30234D-page 4
1997 Microchip Technology Inc.
PIC16C6X
ter (USART) is also known as a Serial Communications
Interface or SCI. An 8-bit Parallel Slave Port is also pro-
vided.
1.0
GENERAL DESCRIPTION
The PIC16CXX is a family of low-cost, high-perfor-
mance, CMOS, fully-static, 8-bit microcontrollers.
The PIC16C6X device family has special features to
reduce external components, thus reducing cost,
enhancing system reliability and reducing power con-
sumption.There are four oscillator options, of which the
single pin RC oscillator provides a low-cost solution,
the LP oscillator minimizes power consumption, XT is a
standard crystal, and the HS is for High Speed crystals.
The SLEEP (power-down) mode offers a power saving
mode. The user can wake the chip from SLEEP
through several external and internal interrupts, and
resets.
All PIC16/17 microcontrollers employ an advanced
RISC architecture.The PIC16CXX microcontroller fam-
ily has enhanced core features, eight-level deep stack,
and multiple internal and external interrupt sources.
The separate instruction and data buses of the Harvard
architecture allow a 14-bit wide instruction word with
separate 8-bit wide data. The two stage instruction
pipeline allows all instructions to execute in a single
cycle, except for program branches (which require two
cycles). A total of 35 instructions (reduced instruction
set) are available. Additionally, a large register set gives
some of the architectural innovations used to achieve a
very high performance.
A highly reliable Watchdog Timer with its own on-chip
RC oscillator provides protection against software lock-
up.
PIC16CXX microcontrollers typically achieve a 2:1
code compression and a 4:1 speed improvement over
other 8-bit microcontrollers in their class.
A UV erasable CERDIP packaged version is ideal for
code
development,
while
the
cost-effective
One-Time-Programmable (OTP) version is suitable for
production in any volume.
The PIC16C61 device has 36 bytes of RAM and 13 I/O
pins. In addition a timer/counter is available.
The PIC16C6X family fits perfectly in applications rang-
ing from high-speed automotive and appliance control
to low-power remote sensors, keyboards and telecom
processors. The EPROM technology makes customi-
zation of application programs (transmitter codes,
motor speeds, receiver frequencies, etc.) extremely
fast and convenient. The small footprint packages
make this microcontroller series perfect for all applica-
tions with space limitations. Low-cost, low-power, high
performance, ease-of-use, and I/O flexibility make the
PIC16C6X very versatile even in areas where no micro-
controller use has been considered before (e.g. timer
functions, serial communication, capture and compare,
PWM functions, and co-processor applications).
The PIC16C62/62A/R62 devices have 128 bytes of
RAM and 22 I/O pins. In addition, several peripheral
features are available, including: three timer/counters,
one Capture/Compare/PWM module and one serial
port. The Synchronous Serial Port can be configured
as either a 3-wire Serial Peripheral Interface (SPI ) or
2
the two-wire Inter-Integrated Circuit (I C) bus.
The PIC16C63/R63 devices have 192 bytes of RAM,
while the PIC16C66 has 368 bytes. All three devices
have 22 I/O pins. In addition, several peripheral fea-
tures are available, including: three timer/counters, two
Capture/Compare/PWM modules and two serial ports.
The Synchronous Serial Port can be configured as
either a 3-wire Serial Peripheral Interface (SPI) or the
2
1.1
Family and Upward Compatibility
two-wire Inter-Integrated Circuit (I C) bus. The Univer-
sal Synchronous Asynchronous Receiver Transmitter
(USART) is also know as a Serial Communications
Interface or SCI.
Those users familiar with the PIC16C5X family of
microcontrollers will realize that this is an enhanced
version of the PIC16C5X architecture. Please refer to
Appendix A for a detailed list of enhancements. Code
written for PIC16C5X can be easily ported to
PIC16CXX family of devices (Appendix B).
The PIC16C64/64A/R64 devices have 128 bytes of
RAM and 33 I/O pins. In addition, several peripheral
features are available, including: three timer/counters,
one Capture/Compare/PWM module and one serial
port. The Synchronous Serial Port can be configured
as either a 3-wire Serial Peripheral Interface (SPI) or
1.2
Development Support
PIC16C6X devices are supported by the complete line
of Microchip Development tools.
2
the two-wire Inter-Integrated Circuit (I C) bus. An 8-bit
Parallel Slave Port is also provided.
Please refer to Section 15.0 for more details about
Microchip’s development tools.
The PIC16C65/65A/R65 devices have 192 bytes of
RAM, while the PIC16C67 has 368 bytes. All four
devices have 33 I/O pins. In addition, several peripheral
features are available, including: three timer/counters,
two Capture/Compare/PWM modules and two serial
ports. The Synchronous Serial Port can be configured
as either a 3-wire Serial Peripheral Interface (SPI) or
2
the two-wire Inter-Integrated Circuit (I C) bus. The Uni-
versal Synchronous Asynchronous Receiver Transmit-
1997 Microchip Technology Inc.
DS30234D-page 5
PIC16C6X
TABLE 1-1:
PIC16C6X FAMILY OF DEVICES
PIC16C61
20
PIC16C62A
20
PIC16CR62
20
PIC16C63
20
PIC16CR63
20
Maximum Frequency
of Operation (MHz)
Clock
EPROM Program Memory
(x14 words)
1K
—
2K
—
—
4K
—
—
Memory
ROM Program Memory
(x14 words)
2K
128
4K
192
Data Memory (bytes)
Timer Module(s)
36
128
192
TMR0
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
Capture/Compare/
PWM Module(s)
—
—
1
1
2
2
Peripherals
2
2
2
2
Serial Port(s)
SPI/I C
SPI/I C
SPI/I C,
USART
SPI/I C
USART
2
(SPI/I C, USART)
Parallel Slave Port
Interrupt Sources
I/O Pins
—
—
—
—
—
3
7
7
10
10
13
22
22
22
22
Voltage Range (Volts)
In-Circuit Serial Programming
Brown-out Reset
Packages
3.0-6.0
Yes
—
2.5-6.0
Yes
Yes
2.5-6.0
Yes
Yes
2.5-6.0
Yes
Yes
2.5-6.0
Yes
Yes
Features
18-pin DIP, SO 28-pin SDIP,
SOIC, SSOP
28-pin SDIP,
SOIC, SSOP
28-pin SDIP, 28-pin SDIP,
SOIC SOIC
PIC16C64A PIC16CR64 PIC16C65A PIC16CR65 PIC16C66 PIC16C67
Maximum Frequency
of Operation (MHz)
20
20
20
20
20
20
Clock
EPROM Program Memory
(x14 words)
2K
—
—
4K
—
—
8K
—
8K
—
Memory
ROM Program Memory (x14
words)
2K
128
4K
192
Data Memory (bytes)
Timer Module(s)
128
192
368
368
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
Capture/Compare/PWM Mod-
ule(s)
1
1
2
2
2
2
Peripherals
2
2
2
2
2
2
2
Serial Port(s) (SPI/I C, USART) SPI/I C
SPI/I C
SPI/I C,
SPI/I C,
SPI/I C,
SPI/I C,
USART
USART
USART
USART
Parallel Slave Port
Interrupt Sources
I/O Pins
Yes
8
Yes
8
Yes
Yes
—
Yes
11
11
10
11
33
33
33
33
22
33
Voltage Range (Volts)
In-Circuit Serial Programming
Brown-out Reset
Packages
2.5-6.0
Yes
Yes
2.5-6.0
Yes
Yes
2.5-6.0
Yes
2.5-6.0
Yes
2.5-6.0
Yes
Yes
2.5-6.0
Yes
Yes
Yes
Yes
Features
40-pin DIP; 40-pin DIP;
40-pin DIP;
40-pin DIP; 28-pin SDIP, 40-pin DIP;
44-pin PLCC, 44-pin PLCC, 44-pin PLCC, 44-pin
MQFP, TQFP MQFP, TQFP MQFP, TQFP PLCC,
SOIC
44-pin
PLCC,
MQFP,
TQFP
MQFP,
TQFP
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer, selectable code protect and high I/O current
capability. All PIC16C6X Family devices use serial programming with clock pin RB6 and data pin RB7.
DS30234D-page 6
1997 Microchip Technology Inc.
PIC16C6X
2.3
Quick-Turnaround-Production (QTP)
Devices
2.0
PIC16C6X DEVICE VARIETIES
A variety of frequency ranges and packaging options
are available. Depending on application and production
requirements, the proper device option can be selected
using the information in the PIC16C6X Product Identifi-
cation System section at the end of this data sheet.
When placing orders, please use that page of the data
sheet to specify the correct part number.
Microchip offers a QTP Programming Service for fac-
tory production orders. This service is made available
for users who choose not to program a medium to high
quantity of units and whose code patterns have stabi-
lized. The devices are identical to the OTP devices but
with all EPROM locations and configuration options
already programmed by the factory. Certain code and
prototype verification procedures apply before produc-
tion shipments are available. Please contact your local
Microchip Technology sales office for more details.
For the PIC16C6X family of devices, there are four
device “types” as indicated in the device number:
1. C, as in PIC16C64. These devices have
EPROM type memory and operate over the
standard voltage range.
2.4
Serialized Quick-Turnaround
Production (SQTPSM) Devices
2. LC, as in PIC16LC64. These devices have
EPROM type memory and operate over an
extended voltage range.
Microchip offers a unique programming service where
a few user-defined locations in each device are pro-
grammed with different serial numbers.The serial num-
bers may be random, pseudo-random, or sequential.
3. CR, as in PIC16CR64. These devices have
ROM program memory and operate over the
standard voltage range.
4. LCR, as in PIC16LCR64. These devices have
ROM program memory and operate over an
extended voltage range.
Serial programming allows each device to have a
unique number which can serve as an entry-code,
password, or ID number.
ROM devices do not allow serialization information in
the program memory space. The user may have this
information programmed in the data memory space.
2.1
UV Erasable Devices
The UV erasable version, offered in CERDIP package
is optimal for prototype development and pilot
programs. This version can be erased and
reprogrammed to any of the oscillator modes.
For information on submitting ROM code, please con-
tact your regional sales office.
2.5
Read Only Memory (ROM) Devices
Microchip's PICSTART Plus and PRO MATE II
programmers both support programming of the
PIC16C6X.
Microchip offers masked ROM versions of several of
the highest volume parts, thus giving customers a low
cost option for high volume, mature products.
2.2
One-Time-Programmable (OTP)
Devices
For information on submitting ROM code, please con-
tact your regional sales office.
The availability of OTP devices is especially useful for
customers who need the flexibility for frequent code
updates and small volume applications.
The OTP devices, packaged in plastic packages, per-
mit the user to program them once. In addition to the
program memory, the configuration bits must also be
programmed.
1997 Microchip Technology Inc.
DS30234D-page 7
PIC16C6X
NOTES:
DS30234D-page 8
1997 Microchip Technology Inc.
PIC16C6X
The PIC16CXX device contains an 8-bit ALU and work-
ing register (W). The ALU is a general purpose arith-
metic unit. It performs arithmetic and Boolean functions
between data in the working register and any register
file.
3.0
ARCHITECTURAL OVERVIEW
The high performance of the PIC16CXX family can be
attributed to a number of architectural features com-
monly found in RISC microprocessors. To begin with,
the PIC16CXX uses a Harvard architecture, in which,
program and data are accessed from separate memo-
ries using separate buses. This improves bandwidth
over traditional von Neumann architecture where pro-
gram and data may be fetched from the same memory
using the same bus. Separating program and data bus-
ses further allows instructions to be sized differently
than 8-bit wide data words. Instruction opcodes are
14-bits wide making it possible to have all single word
instructions. A 14-bit wide program memory access
bus fetches a 14-bit instruction in a single cycle. A two-
stage pipeline overlaps fetch and execution of instruc-
tions (Example 3-1). Consequently, all instructions exe-
cute in a single cycle (200 ns @ 20 MHz) except for
program branches.
The ALU is 8-bits wide and capable of addition, sub-
traction, shift, and logical operations. Unless otherwise
mentioned, arithmetic operations are two's comple-
ment in nature. In two-operand instructions, typically
one operand is the working register (W register), the
other operand is a file register or an immediate con-
stant. In single operand instructions, the operand is
either the W register or a file register.
The W register is an 8-bit working register used for ALU
operations. It is not an addressable register.
Depending upon the instruction executed, the ALU may
affect the values of the Carry (C), Digit Carry (DC), and
Zero (Z) bits in the STATUS register. Bits C and DC
operate as a borrow and digit borrow out bit, respec-
tively, in subtraction. See the SUBLW and SUBWF
instructions for examples.
The PIC16C61 addresses 1K x 14 of program memory.
The PIC16C62/62A/R62/64/64A/R64 address 2K x 14 of
program memory, and the PIC16C63/R63/65/65A/R65
devices address 4K x 14 of program memory. The
PIC16C66/67 address 8K x 14 program memory. All
program memory is internal.
The PIC16CXX can directly or indirectly address its
register files or data memory. All special function reg-
isters including the program counter are mapped in
the data memory. The PIC16CXX has an orthogonal
(symmetrical) instruction set that makes it possible to
carry out any operation on any register using any
addressing mode. This symmetrical nature and lack of
“special optimal situations” makes programming with
the PIC16CXX simple yet efficient, thus significantly
reducing the learning curve.
1997 Microchip Technology Inc.
DS30234D-page 9
PIC16C6X
FIGURE 3-1: PIC16C61 BLOCK DIAGRAM
13
8
PORTA
Data Bus
Program Counter
EPROM
RA0
RA1
RA2
RA3
Program
Memory
RAM
File
Registers
8 Level Stack
1K x 14
(13-bit)
RA4/T0CKI
36 x 8
Program
14
RAM Addr(1)
PORTB
Bus
9
Addr MUX
Instruction reg
RB0/INT
RB7:RB1
Indirect
Addr
7
Direct Addr
8
FSR reg
STATUS reg
8
3
MUX
Power-up
Timer
Oscillator
Instruction
Decode &
Control
Start-up Timer
ALU
Power-on
Reset
8
Timing
Generation
Watchdog
Timer
W reg
OSC1/CLKIN
OSC2/CLKOUT
Timer0
MCLR VDD, VSS
Note 1: Higher order bits are from the STATUS register.
DS30234D-page 10
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 3-2: PIC16C62/62A/R62/64/64A/R64 BLOCK DIAGRAM
13
8
PORTA
Data Bus
Program Counter
EPROM/
ROM
Program
Memory
RA0
RA1
RA2
RA3
RAM
File
Registers
8 Level Stack
(13-bit)
2K x 14
RA4/T0CKI
RA5/SS
128 x 8
Program
Bus
14
RAM Addr(1)
PORTB
9
Addr MUX
Instruction reg
RB0/INT
RB7:RB1
Indirect
Addr
7
Direct Addr
8
FSR reg
STATUS reg
8
PORTC
RC0/T1OSO/T1CKI(4)
RC1/T1OSI(4)
RC2/CCP1
RC3/SCK/SCL
RC4/SDI/SDA
RC5/SDO
3
MUX
Power-up
Timer
Oscillator
Instruction
Decode &
Control
Start-up Timer
ALU
RC6
Power-on
Reset
RC7
8
Timing
Generation
Watchdog
Timer
W reg
PORTD
OSC1/CLKIN
OSC2/CLKOUT
Brown-out
RD0/PSP0
RD1/PSP1
RD2/PSP2
RD3/PSP3
RD4/PSP4
RD5/PSP5
RD6/PSP6
RD7/PSP7
Reset(3)
MCLR VDD, VSS
Parallel Slave
Port
PORTE
RE0/RD
RE1/WR
RE2/CS
Timer1
Timer0
Timer2
CCP1
(Note 2)
Synchronous
Serial Port
Note 1: Higher order bits are from the STATUS register.
2: PORTD, PORTE and the Parallel Slave Port are not available on the PIC16C62/62A/R62.
3: Brown-out Reset is not available on the PIC16C62/64.
4: Pin functions T1OSI and T1OSO are swapped on the PIC16C62/64.
1997 Microchip Technology Inc.
DS30234D-page 11
PIC16C6X
FIGURE 3-3: PIC16C63/R63/65/65A/R65 BLOCK DIAGRAM
13
8
PORTA
Data Bus
Program Counter
EPROM
RA0
RA1
RA2
RA3
RA4/T0CKI
Program
Memory
RAM
File
Registers
8 Level Stack
(13-bit)
4K x 14
192 x 8
RA5/SS
Program
Bus
14
RAM Addr(1)
PORTB
9
Addr MUX
Instruction reg
RB0/INT
RB7:RB1
Indirect
Addr
7
Direct Addr
8
FSR reg
STATUS reg
8
PORTC
RC0/T1OSO/T1CKI
RC1/T1OSI/CCP2
RC2/CCP1
3
MUX
Power-up
Timer
RC3/SCK/SCL
RC4/SDI/SDA
RC5/SDO
RC6/TX/CK
RC7/RX/DT
Oscillator
Instruction
Decode &
Control
Start-up Timer
ALU
Power-on
Reset
8
Timing
Generation
Watchdog
Timer
W reg
PORTD
OSC1/CLKIN
OSC2/CLKOUT
Brown-out
Reset(3)
RD0/PSP0
RD1/PSP1
RD2/PSP2
RD3/PSP3
RD4/PSP4
RD5/PSP5
RD6/PSP6
RD7/PSP7
MCLR VDD, VSS
Parallel Slave
Port
PORTE
RE0/RD
RE1/WR
RE2/CS
Timer0
USART
Timer1
Timer2
CCP1
(Note 2)
Synchronous
Serial Port
CCP2
Note 1: Higher order bits are from the STATUS register.
2: PORTD, PORTE and the Parallel Slave Port are not available on the PIC16C63/R63.
3: Brown-out Reset is not available on the PIC16C65.
DS30234D-page 12
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 3-4: PIC16C66/67 BLOCK DIAGRAM
13
8
PORTA
Data Bus
Program Counter
EPROM
RA0
RA1
RA2
RA3
RA4/T0CKI
Program
Memory
RAM
File
Registers
8 Level Stack
8K x 14
(13-bit)
368 x 8
RA5/SS
Program
14
RAM Addr(1)
PORTB
Bus
9
Addr MUX
Instruction reg
RB0/INT
RB7:RB1
Indirect
Addr
7
Direct Addr
8
FSR reg
STATUS reg
8
PORTC
RC0/T1OSO/T1CKI
RC1/T1OSI/CCP2
RC2/CCP1
3
MUX
Power-up
Timer
RC3/SCK/SCL
RC4/SDI/SDA
RC5/SDO
RC6/TX/CK
RC7/RX/DT
Oscillator
Instruction
Decode &
Control
Start-up Timer
ALU
Power-on
Reset
8
Timing
Generation
Watchdog
Timer
W reg
PORTD
OSC1/CLKIN
OSC2/CLKOUT
Brown-out
Reset
RD0/PSP0
RD1/PSP1
RD2/PSP2
RD3/PSP3
RD4/PSP4
RD5/PSP5
RD6/PSP6
RD7/PSP7
MCLR VDD, VSS
Parallel Slave
Port
PORTE
RE0/RD
RE1/WR
RE2/CS
Timer0
USART
Timer1
Timer2
CCP1
(Note 2)
Synchronous
Serial Port
CCP2
Note 1: Higher order bits are from the STATUS register.
2: PORTD, PORTE and the Parallel Slave Port are not available on the PIC16C66.
1997 Microchip Technology Inc.
DS30234D-page 13
PIC16C6X
TABLE 3-1:
PIC16C61 PINOUT DESCRIPTION
DIP
Pin#
SOIC
Pin#
Buffer
Type
Pin Name
Pin Type
Description
(1)
OSC1/CLKIN
16
15
16
15
I
Oscillator crystal input/external clock source input.
ST/CMOS
—
OSC2/CLKOUT
O
Oscillator crystal output. Connects to crystal or resonator in crystal
oscillator mode. In RC mode, the pin outputs CLKOUT which has
1/4 the frequency of OSC1, and denotes the instruction cycle rate.
4
4
I/P
ST
Master clear reset input or programming voltage input.This pin is an
active low reset to the device.
MCLR/VPP
PORTA is a bi-directional I/O port.
RA0
17
18
1
17
18
1
I/O
I/O
I/O
I/O
I/O
TTL
TTL
TTL
TTL
ST
RA1
RA2
RA3
2
2
RA4/T0CKI
3
3
RA4 can also be the clock input to the Timer0 timer/counter.
Output is open drain type.
PORTB is a bi-directional I/O port. PORTB can be software pro-
grammed for internal weak pull-up on all inputs.
(2)
RB0/INT
6
7
6
7
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
P
TTL/ST
TTL
RB0 can also be the external interrupt pin.
RB1
RB2
8
8
TTL
RB3
9
9
TTL
RB4
10
11
12
13
5
10
11
12
13
5
TTL
Interrupt on change pin.
RB5
TTL
Interrupt on change pin.
(3)
RB6
TTL/ST
TTL/ST
—
Interrupt on change pin. Serial programming clock.
Interrupt on change pin. Serial programming data.
Ground reference for logic and I/O pins.
Positive supply for logic and I/O pins.
(3)
RB7
VSS
VDD
14
14
P
—
Legend: I = input
O = output
— = Not used
I/O = input/output
TTL = TTL input
P = power
ST = Schmitt Trigger input
Note 1: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise.
2: This buffer is a Schmitt Trigger input when configured as the external interrupt.
3: This buffer is a Schmitt Trigger input when used in serial programming mode.
DS30234D-page 14
1997 Microchip Technology Inc.
PIC16C6X
TABLE 3-2:
PIC16C62/62A/R62/63/R63/66 PINOUT DESCRIPTION
Buffer
Type
Pin Name
Pin#
Pin Type
Description
(3)
OSC1/CLKIN
9
I
Oscillator crystal input/external clock source input.
ST/CMOS
—
OSC2/CLKOUT
10
O
Oscillator crystal output. Connects to crystal or resonator in crys-
tal oscillator mode. In RC mode, the pin outputs CLKOUT which
has 1/4 the frequency of OSC1, and denotes the instruction cycle
rate.
1
I/P
ST
Master clear reset input or programming voltage input.This pin is
an active low reset to the device.
MCLR/VPP
PORTA is a bi-directional I/O port.
RA0
2
3
4
5
6
I/O
I/O
I/O
I/O
I/O
TTL
TTL
TTL
TTL
ST
RA1
RA2
RA3
RA4/T0CKI
RA4 can also be the clock input to the Timer0 timer/counter.
Output is open drain type.
RA5/SS
7
I/O
TTL
RA5 can also be the slave select for the synchronous serial
port.
PORTB is a bi-directional I/O port. PORTB can be software pro-
grammed for internal weak pull-up on all inputs.
(4)
RB0/INT
RB1
21
22
23
24
25
26
27
28
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
TTL/ST
TTL
RB0 can also be the external interrupt pin.
RB2
TTL
RB3
TTL
RB4
TTL
Interrupt on change pin.
RB5
TTL
Interrupt on change pin.
(5)
RB6
TTL/ST
TTL/ST
Interrupt on change pin. Serial programming clock.
Interrupt on change pin. Serial programming data.
PORTC is a bi-directional I/O port.
(5)
RB7
(1)
(1)
11
12
13
14
15
I/O
I/O
I/O
I/O
I/O
ST
ST
ST
ST
ST
RC0 can also be the Timer1 oscillator output or Timer1
clock input.
RC0/T1OSO /T1CKI
(1)
(1)
(2)
RC1 can also be the Timer1 oscillator input or Capture2
RC1/T1OSI /CCP2
(2)
input/Compare2 output/PWM2 output
.
RC2/CCP1
RC2 can also be the Capture1 input/Compare1 out-
put/PWM1 output.
RC3/SCK/SCL
RC4/SDI/SDA
RC5/SDO
RC3 can also be the synchronous serial clock input/output
2
for both SPI and I C modes.
RC4 can also be the SPI Data In (SPI mode) or
2
data I/O (I C mode).
16
17
I/O
I/O
ST
ST
RC5 can also be the SPI Data Out (SPI mode).
(2)
(2)
RC6 can also be the USART Asynchronous Transmit or
RC6/TX/CK
(2)
Synchronous Clock
.
(2)
(2)
18
I/O
ST
RC7 can also be the USART Asynchronous Receive or
RC7/RX/DT
(2)
Synchronous Data
.
VSS
8,19
20
P
P
—
—
Ground reference for logic and I/O pins.
Positive supply for logic and I/O pins.
VDD
Legend: I = input
O = output
— = Not used
I/O = input/output
TTL = TTL input
P = power
ST = Schmitt Trigger input
Note 1: Pin functions T1OSO and T1OSI are reversed on the PIC16C62.
2: The USART and CCP2 are not available on the PIC16C62/62A/R62.
3: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise.
4: This buffer is a Schmitt Trigger input when configured as the external interrupt.
5: This buffer is a Schmitt Trigger input when used in serial programming mode.
1997 Microchip Technology Inc.
DS30234D-page 15
PIC16C6X
TABLE 3-3:
PIC16C64/64A/R64/65/65A/R65/67 PINOUT DESCRIPTION
TQFP
MQFP
Pin#
DIP
Pin#
PLCC
Pin#
Pin
Type
Buffer
Type
Pin Name
Description
(3)
OSC1/CLKIN
13
14
14
15
30
31
I
Oscillator crystal input/external clock source input.
ST/CMOS
—
OSC2/CLKOUT
O
Oscillator crystal output. Connects to crystal or resonator in
crystal oscillator mode. In RC mode, the pin outputs CLK-
OUT which has 1/4 the frequency of OSC1, and denotes the
instruction cycle rate.
1
2
18
I/P
ST
Master clear reset input or programming voltage input. This
pin is an active low reset to the device.
MCLR/VPP
PORTA is a bi-directional I/O port.
RA0
2
3
4
5
6
3
4
5
6
7
19
20
21
22
23
I/O
I/O
I/O
I/O
I/O
TTL
TTL
TTL
TTL
ST
RA1
RA2
RA3
RA4/T0CKI
RA4 can also be the clock input to the Timer0
timer/counter. Output is open drain type.
RA5/SS
7
8
24
I/O
TTL
RA5 can also be the slave select for the synchronous
serial port.
PORTB is a bi-directional I/O port. PORTB can be software
programmed for internal weak pull-up on all inputs.
(4)
RB0/INT
RB1
33
34
35
36
37
38
39
40
36
37
38
39
41
42
43
44
8
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
TTL/ST
TTL
RB0 can also be the external interrupt pin.
9
RB2
10
11
14
15
16
17
TTL
RB3
TTL
RB4
TTL
Interrupt on change pin.
RB5
TTL
Interrupt on change pin.
(5)
RB6
TTL/ST
TTL/ST
Interrupt on change pin. Serial programming clock.
Interrupt on change pin. Serial programming data.
PORTC is a bi-directional I/O port.
(5)
RB7
(1)
(1)
RC0/T1OSO /T1CKI
15
16
17
18
23
16
18
19
20
25
32
35
36
37
42
I/O
I/O
I/O
I/O
I/O
ST
ST
ST
ST
ST
RC0 can also be the Timer1 oscillator output or
Timer1 clock input.
(1)
(2)
(1)
RC1/T1OSI /CCP2
RC1 can also be the Timer1 oscillator input
Capture2 input/Compare2 output/PWM2 output
or
(2)
.
RC2/CCP1
RC2 can also be the Capture1 input/Compare1 out-
put/PWM1 output.
RC3/SCK/SCL
RC4/SDI/SDA
RC5/SDO
RC3 can also be the synchronous serial clock input/out-
2
put for both SPI and I C modes.
RC4 can also be the SPI Data In (SPI mode) or
2
data I/O (I C mode).
24
25
26
27
43
44
I/O
I/O
ST
ST
RC5 can also be the SPI Data Out (SPI mode).
(2)
(2)
RC6/TX/CK
RC6 can also be the USART Asynchronous Transmit
(2)
or Synchronous Clock
.
(2)
(2)
RC7/RX/DT
26
29
1
I/O
ST
RC7 can also be the USART Asynchronous Receive
(2)
or Synchronous Data
P = power
ST = Schmitt Trigger input
.
Legend: I = input
O = output
— = Not used
I/O = input/output
TTL = TTL input
Note 1: Pin functions T1OSO and T1OSI are reversed on the PIC16C64.
2: CCP2 and the USART are not available on the PIC16C64/64A/R64.
3: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise.
4: This buffer is a Schmitt Trigger input when configured as the external interrupt.
5: This buffer is a Schmitt Trigger input when used in serial programming mode.
6: This buffer is a Schmitt Trigger input when configured as general purpose I/O and a TTL input when used in the Parallel Slave
Port mode (for interfacing to a microprocessor bus).
DS30234D-page 16
1997 Microchip Technology Inc.
PIC16C6X
TABLE 3-3:
PIC16C64/64A/R64/65/65A/R65/67 PINOUT DESCRIPTION (Cont.’d)
TQFP
MQFP
Pin#
DIP
Pin#
PLCC
Pin#
Pin
Type
Buffer
Type
Pin Name
Description
PORTD can be a bi-directional I/O port or parallel slave port
for interfacing to a microprocessor bus.
(6)
RD0/PSP0
RD1/PSP1
RD2/PSP2
RD3/PSP3
RD4/PSP4
RD5/PSP5
RD6/PSP6
RD7/PSP7
19
20
21
22
27
28
29
30
21
22
23
24
30
31
32
33
38
39
40
41
2
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
ST/TTL
ST/TTL
ST/TTL
ST/TTL
ST/TTL
ST/TTL
ST/TTL
ST/TTL
(6)
(6)
(6)
(6)
(6)
(6)
(6)
3
4
5
PORTE is a bi-directional I/O port.
(6)
(6)
(6)
RE0/RD
RE1/WR
RE2/CS
VSS
8
9
9
25
26
I/O
I/O
I/O
P
ST/TTL
ST/TTL
ST/TTL
—
RE0 can also be read control for the parallel slave port.
RE1 can also be write control for the parallel slave port.
RE2 can also be select control for the parallel slave port.
Ground reference for logic and I/O pins.
10
11
10
27
12,31 13,34
11,32 12,35
6,29
7,28
VDD
P
—
Positive supply for logic and I/O pins.
NC
—
1,17,
28,40
12,13,
33,34
—
—
These pins are not internally connected. These pins should
be left unconnected.
Legend: I = input
O = output
— = Not used
I/O = input/output
TTL = TTL input
P = power
ST = Schmitt Trigger input
Note 1: Pin functions T1OSO and T1OSI are reversed on the PIC16C64.
2: CCP2 and the USART are not available on the PIC16C64/64A/R64.
3: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise.
4: This buffer is a Schmitt Trigger input when configured as the external interrupt.
5: This buffer is a Schmitt Trigger input when used in serial programming mode.
6: This buffer is a Schmitt Trigger input when configured as general purpose I/O and a TTL input when used in the Parallel Slave
Port mode (for interfacing to a microprocessor bus).
1997 Microchip Technology Inc.
DS30234D-page 17
PIC16C6X
3.1
Clocking Scheme/Instruction Cycle
3.2
Instruction Flow/Pipelining
The clock input (from OSC1) is internally divided by
four to generate four non-overlapping quadrature
clocks namely Q1, Q2, Q3, and Q4. Internally, the pro-
gram counter (PC) is incremented every Q1, the
instruction is fetched from the program memory and
latched into the instruction register in Q4. The instruc-
tion is decoded and executed during the following Q1
through Q4. The clock and instruction execution flow is
shown in Figure 3-5.
An “Instruction Cycle” consists of four Q cycles (Q1,
Q2, Q3, and Q4). The instruction fetch and execute are
pipelined such that fetch takes one instruction cycle
while decode and execute takes another instruction
cycle. However, due to the pipelining, each instruction
effectively executes in one cycle. If an instruction
causes the program counter to change (e.g. GOTO)
then two cycles are required to complete the instruction
(Example 3-1).
A fetch cycle begins with the program counter (PC)
incrementing in Q1.
In the execution cycle, the fetched instruction is latched
into the “Instruction Register (IR)” in cycle Q1. This
instruction is then decoded and executed during the
Q2, Q3, and Q4 cycles. Data memory is read during Q2
(operand read) and written during Q4 (destination
write).
FIGURE 3-5: CLOCK/INSTRUCTION CYCLE
Q2
Q3
Q4
Q2
Q3
Q4
Q2
Q3
Q4
Q1
Q1
Q1
OSC1
Q1
Internal
Phase
Clock
Q2
Q3
Q4
PC
PC
PC+1
PC+2
(Program counter)
OSC2/CLKOUT
(RC mode)
Fetch INST (PC)
Fetch INST (PC+1)
Execute INST (PC)
Execute INST (PC-1)
Fetch INST (PC+2)
Execute INST (PC+1)
EXAMPLE 3-1: INSTRUCTION PIPELINE FLOW
Tcy0
Tcy1
Tcy2
Tcy3
Tcy4
Tcy5
1. MOVLW 55h
Fetch 1
Execute 1
Fetch 2
2. MOVWF PORTB
3. CALL SUB_1
Execute 2
Fetch 3
Execute 3
Fetch 4
4. BSF
PORTA, BIT3 (Forced NOP)
Flush
5. Instruction @ address SUB_1
Fetch SUB_1 Execute SUB_1
All instructions are single cycle, except for any program branches. These take two cycles since the fetch
instruction is “flushed” from the pipeline while the new instruction is being fetched and then executed.
DS30234D-page 18
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 4-2: PIC16C62/62A/R62/64/64A/
R64 PROGRAM MEMORY
4.0
MEMORY ORGANIZATION
Applicable Devices
MAP AND STACK
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PC<12:0>
4.1
Program Memory Organization
13
CALL, RETURN
RETFIE, RETLW
The PIC16C6X family has a 13-bit program counter
capable of addressing an 8K x 14 program memory
space. The amount of program memory available to
each device is listed below:
Stack Level 1
•
•
•
Stack Level 8
Program
Memory
Reset Vector
0000h
Device
Address Range
Peripheral Interrupt Vector
0004h
0005h
PIC16C61
PIC16C62
PIC16C62A
PIC16CR62
PIC16C63
PIC16CR63
PIC16C64
PIC16C64A
PIC16CR64
PIC16C65
PIC16C65A
PIC16CR65
PIC16C66
PIC16C67
1K x 14
2K x 14
2K x 14
2K x 14
4K x 14
4K x 14
2K x 14
2K x 14
2K x 14
4K x 14
4K x 14
4K x 14
8K x 14
8K x 14
0000h-03FFh
0000h-07FFh
0000h-07FFh
0000h-07FFh
0000h-0FFFh
0000h-0FFFh
0000h-07FFh
0000h-07FFh
0000h-07FFh
0000h-0FFFh
0000h-0FFFh
0000h-0FFFh
0000h-1FFFh
0000h-1FFFh
On-chip Program
Memory
07FFh
0800h
1FFFh
FIGURE 4-3: PIC16C63/R63/65/65A/R65
PROGRAM MEMORY MAP
AND STACK
PC<12:0>
13
For those devices with less than 8K program memory,
accessing a location above the physically implemented
address will cause a wraparound.
CALL, RETURN
RETFIE, RETLW
Stack Level 1
•
•
•
The reset vector is at 0000h and the interrupt vector is
at 0004h.
Stack Level 8
0000h
Reset Vector
FIGURE 4-1: PIC16C61 PROGRAM
MEMORY MAP AND STACK
0004h
0005h
Peripheral Interrupt Vector
PC<12:0>
13
CALL, RETURN
RETFIE, RETLW
On-chip Program
Memory (Page 0)
Stack Level 1
•
•
•
07FFh
0800h
Stack Level 8
Reset Vector
0000h
On-chip Program
Memory (Page 1)
Peripheral Interrupt Vector
0004h
0005h
On-chip Program
Memory
0FFFh
1000h
03FFh
0400h
1FFFh
1FFFh
1997 Microchip Technology Inc.
DS30234D-page 19
PIC16C6X
For the PIC16C61, general purpose register locations
8Ch-AFh of Bank 1 are not physically implemented.
These locations are mapped into 0Ch-2Fh of Bank 0.
FIGURE 4-4: PIC16C66/67 PROGRAM
MEMORY MAP AND STACK
PC<12:0>
FIGURE 4-5: PIC16C61 REGISTER FILE
MAP
13
CALL, RETURN
RETFIE, RETLW
Stack Level 1
File Address
00h
File Address
80h
•
•
•
INDF(1)
TMR0
PCL
INDF(1)
OPTION
PCL
Stack Level 8
01h
81h
0000h
Reset Vector
02h
82h
0004h
0005h
Peripheral Interrupt Vector
STATUS
FSR
STATUS
FSR
03h
83h
04h
84h
On-chip Program
Memory (Page 0)
PORTA
PORTB
TRISA
TRISB
05h
85h
06h
07FFh
0800h
86h
07h
87h
88h
On-chip Program
Memory (Page 1)
08h
0FFFh
1000h
89h
8Ah
09h
PCLATH
INTCON
PCLATH
INTCON
On-chip Program
Memory (Page 2)
0Ah
0Bh
8Bh
8Ch
17FFh
1800h
0Ch
On-chip Program
Memory (Page 3)
General
Purpose
Register
Mapped
(2)
in Bank 0
1FFFh
AFh
B0h
2Fh
30h
4.2
Data Memory Organization
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The data memory is partitioned into multiple banks
which contain the General Purpose Registers and the
Special Function Registers. Bits RP1 and RP0 are the
bank select bits.
RP1:RP0 (STATUS<6:5>)
= 00 → Bank0
= 01 → Bank1
= 10 → Bank2
= 11 → Bank3
7Fh
FFh
Bank 0
Each bank extends up to 7Fh (128 bytes). The lower
locations of each bank are reserved for the Special
Function Registers. Above the Special Function Regis-
ters are General Purpose Registers, implemented as
static RAM. All implemented banks contain special
function registers. Some “high use” special function
registers from one bank may be mirrored in another
bank for code reduction and quicker access.
Bank 1
Unimplemented data memory location; read as '0'.
Note 1: Not a physical register.
2: These locations are unimplemented in
Bank 1. Any access to these locations will
access the corresponding Bank 0 register.
4.2.1
GENERAL PURPOSE REGISTERS
These registers are accessed either directly or indi-
rectly through the File Select Register (FSR)
(Section 4.5).
DS30234D-page 20
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 4-6: PIC16C62/62A/R62/64/64A/
R64 REGISTER FILE MAP
FIGURE 4-7: PIC16C63/R63/65/65A/R65
REGISTER FILE MAP
File Address
00h
File Address
File Address
00h
File Address
80h
INDF(1)
TMR0
PCL
INDF(1)
OPTION
PCL
INDF(1)
TMR0
PCL
INDF(1)
OPTION
PCL
80h
81h
82h
83h
84h
85h
86h
01h
01h
81h
02h
02h
82h
STATUS
FSR
STATUS
FSR
03h
STATUS
FSR
STATUS
FSR
03h
83h
04h
04h
84h
PORTA
TRISA
05h
PORTA
TRISA
05h
85h
PORTB
PORTC
TRISB
TRISC
06h
PORTB
PORTC
TRISB
TRISC
06h
86h
07h
87h
88h
07h
87h
88h
PORTD(2)
PORTE(2)
TRISD(2)
TRISE(2)
PORTD(2)
PORTE(2)
TRISD(2)
TRISE(2)
08h
08h
89h
8Ah
89h
8Ah
09h
0Ah
09h
0Ah
PCLATH
INTCON
PCLATH
INTCON
PCLATH
INTCON
PCLATH
INTCON
8Bh
8Ch
8Bh
8Ch
0Bh
0Ch
0Bh
0Ch
PIR1
PIE1
PIR1
PIR2
PIE1
PIE2
8Dh
8Eh
8Fh
8Dh
8Eh
8Fh
0Dh
0Eh
0Fh
0Dh
0Eh
0Fh
TMR1L
TMR1H
PCON
TMR1L
TMR1H
PCON
90h
91h
90h
91h
10h
11h
T1CON
TMR2
10h
11h
T1CON
TMR2
92h
92h
T2CON
SSPBUF
12h
PR2
T2CON
SSPBUF
12h
PR2
93h
94h
SSPADD
SSPSTAT
93h
94h
13h
14h
SSPADD
SSPSTAT
13h
14h
SSPCON
CCPR1L
CCPR1H
CCP1CON
SSPCON
CCPR1L
CCPR1H
CCP1CON
95h
96h
97h
95h
96h
97h
15h
16h
17h
15h
16h
17h
98h
98h
99h
9Ah
18h
18h
19h
1Ah
RCSTA
TXREG
RCREG
TXSTA
SPBRG
9Bh
9Ch
9Dh
9Eh
CCPR2L
CCPR2H
1Bh
1Ch
1Dh
1Eh
9Fh
A0h
1Fh
20h
CCP2CON
General
Purpose
Register
General
Purpose
Register
BFh
C0h
9Fh
A0h
1Fh
20h
General
Purpose
Register
General
Purpose
Register
7Fh
7Fh
FFh
FFh
Bank 1
Bank 0
Bank 1
Bank 0
Unimplemented data memory location; read as '0'.
Note 1: Not a physical register.
Unimplemented data memory location; read as '0'.
Note 1: Not a physical register
2: PORTD and PORTE are not available on
the PIC16C62/62A/R62.
2: PORTD and PORTE are not available on
the PIC16C63/R63.
1997 Microchip Technology Inc.
DS30234D-page 21
PIC16C6X
FIGURE 4-8: PIC16C66/67 DATA MEMORY MAP
File
Address
(*)
(*)
(*)
(*)
Indirect addr.
Indirect addr.
OPTION
PCL
100h
101h
102h
103h
104h
105h
106h
107h
108h
109h
10Ah
10Bh
10Ch
10Dh
10Eh
10Fh
110h
111h
112h
113h
114h
115h
116h
117h
118h
119h
11Ah
11Bh
11Ch
11Dh
11Eh
11Fh
120h
Indirect addr.
TMR0
Indirect addr.
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
1Fh
20h
180h
181h
182h
183h
184h
185h
186h
187h
188h
189h
18Ah
18Bh
18Ch
18Dh
18Eh
18Fh
190h
191h
192h
193h
194h
195h
196h
197h
198h
199h
19Ah
19Bh
19Ch
19Dh
19Eh
19Fh
80h
81h
82h
83h
84h
85h
86h
87h
88h
89h
8Ah
8Bh
8Ch
8Dh
8Eh
8Fh
90h
91h
92h
93h
94h
95h
96h
97h
98h
99h
9Ah
9Bh
9Ch
9Dh
9Eh
9Fh
TMR0
PCL
OPTION
PCL
PCL
STATUS
FSR
STATUS
FSR
STATUS
FSR
STATUS
FSR
PORTA
PORTB
PORTC
TRISA
TRISB
TRISC
TRISB
PORTB
TRISD (1)
TRISE (1)
PORTD (1)
PORTE (1)
PCLATH
INTCON
PIR1
PCLATH
INTCON
PCLATH
INTCON
PCLATH
INTCON
PIE1
PIR2
TMR1L
PIE2
PCON
TMR1H
T1CON
TMR2
T2CON
SSPBUF
SSPCON
CCPR1L
CCPR1H
CCP1CON
PR2
SSPADD
SSPSTAT
General
Purpose
Register
General
Purpose
Register
RCSTA
TXREG
TXSTA
16 Bytes
16 Bytes
SPBRG
RCREG
CCPR2L
CCPR2H
CCP2CON
1A0h
A0h
General
Purpose
Register
General
Purpose
Register
General
Purpose
Register
General
Purpose
Register
80 Bytes
80 Bytes
80 Bytes
1EFh
1F0h
96 Bytes
EFh
F0h
16Fh
170h
accesses
70h-7Fh
in Bank 0
accesses
70h-7Fh
in Bank 0
accesses
70h-7Fh
in Bank 0
17Fh
1FFh
7Fh
FFh
Bank 3
Bank 2
Bank 1
Bank 0
Unimplemented data memory locations, read as '0'.
Not a physical register.
*
These registers are not implemented on the PIC16C66.
Note: The upper 16 bytes of data memory in banks 1, 2, and 3 are mapped in Bank 0. This may require
relocation of data memory usage in the user application code if upgrading to the PIC16C66/67.
DS30234D-page 22
1997 Microchip Technology Inc.
PIC16C6X
4.2.2
SPECIAL FUNCTION REGISTERS:
The special function registers can be classified into two
sets (core and peripheral). The registers associated
with the “core” functions are described in this section
and those related to the operation of the peripheral fea-
tures are described in the section of that peripheral fea-
ture.
The Special Function Registers are registers used by
the CPU and peripheral modules for controlling the
desired operation of the device. These registers are
implemented as static RAM.
TABLE 4-1:
SPECIAL FUNCTION REGISTERS FOR THE PIC16C61
Value on
Value on:
POR
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
all other
resets(3)
Bank 0
00h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
Timer0 module’s register
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
0000 0000 0000 0000
0001 1xxx 000q quuu
01h
TMR0
PCL
02h(1)
03h(1)
Program Counter's (PC) Least Significant Byte
IRP(4)
RP1(4)
STATUS
RP0
Indirect data memory address pointer
PORTA Data Latch when written: PORTA pins when read
TO
PD
Z
DC
C
04h(1)
05h
FSR
PORTA
PORTB
—
xxxx xxxx uuuu uuuu
---x xxxx ---u uuuu
xxxx xxxx uuuu uuuu
—
—
—
06h
PORTB Data Latch when written: PORTB pins when read
07h
Unimplemented
Unimplemented
Unimplemented
—
—
—
—
—
—
—
08h
—
09h
0Ah(1,2)
Write Buffer for the upper 5 bits of the Program Counter
INTE RBIE T0IF INTF RBIF
PCLATH
INTCON
—
—
—
—
---0 0000 ---0 0000
0-00 000x 0-00 000u
0Bh(1)
GIE
T0IE
Bank 1
80h(1)
81h
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
0000 0000 0000 0000
1111 1111 1111 1111
0000 0000 0000 0000
0001 1xxx 000q quuu
OPTION
PCL
RBPU
Program Counter's (PC) Least Significant Byte
RP0 TO
Indirect data memory address pointer
PORTA Data Direction Register
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
82h(1)
83h(1)
IRP(4)
RP1(4)
STATUS
PD
Z
DC
C
84h(1)
85h
FSR
TRISA
TRISB
–
xxxx xxxx uuuu uuuu
---1 1111 ---1 1111
1111 1111 1111 1111
—
—
—
86h
PORTB Data Direction Control Register
Unimplemented
87h
—
—
—
—
—
—
–
Unimplemented
88h
89h
Unimplemented
–
8Ah(1,2)
8Bh(1)
Write Buffer for the upper 5 bits of the Program Counter
INTE RBIE T0IF INTF RBIF
PCLATH
INTCON
—
—
—
—
---0 0000 ---0 0000
0-00 000x 0-00 000u
GIE
T0IE
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented locations read as '0'.
Shaded locations are unimplemented and read as ‘0’
Note 1: These registers can be addressed from either bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose con-
tents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer Reset.
4: The IRP and RP1 bits are reserved on the PIC16C61, always maintain these bits clear.
1997 Microchip Technology Inc.
DS30234D-page 23
PIC16C6X
TABLE 4-2:
SPECIAL FUNCTION REGISTERS FOR THE PIC16C62/62A/R62
Value on:
POR,
BOR
Value on
all other
resets(3)
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Bank 0
00h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
Timer0 module’s register
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
0000 0000 0000 0000
0001 1xxx 000q quuu
01h
TMR0
PCL
02h(1)
03h(1)
Program Counter's (PC) Least Significant Byte
IRP(5)
RP1(5)
STATUS
RP0
Indirect data memory address pointer
PORTA Data Latch when written: PORTA pins when read
TO
PD
Z
DC
C
04h(1)
05h
06h
07h
08h
09h
FSR
xxxx xxxx uuuu uuuu
--xx xxxx --uu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
PORTA
PORTB
PORTC
—
—
—
PORTB Data Latch when written: PORTB pins when read
PORTC Data Latch when written: PORTC pins when read
Unimplemented
—
—
—
—
—
Unimplemented
0Ah(1,2)
Write Buffer for the upper 5 bits of the Program Counter
PCLATH
—
GIE
(6)
—
PEIE
(6)
—
T0IE
—
---0 0000 ---0 0000
0000 000x 0000 000u
0Bh(1)
0Ch
0Dh
0Eh
0Fh
INTCON
PIR1
INTE
—
RBIE
T0IF
INTF
RBIF
SSPIF
CCP1IF
TMR2IF
TMR1IF 00-- 0000 00-- 0000
—
Unimplemented
—
—
TMR1L
TMR1H
T1CON
TMR2
Holding register for the Least Significant Byte of the 16-bit TMR1 register
Holding register for the Most Significant Byte of the 16-bit TMR1 register
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
10h
—
—
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu
11h
Timer2 module’s register
0000 0000 0000 0000
12h
T2CON
SSPBUF
SSPCON
CCPR1L
CCPR1H
CCP1CON
—
—
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000
13h
Synchronous Serial Port Receive Buffer/Transmit Register
xxxx xxxx uuuu uuuu
SSPM0 0000 0000 0000 0000
xxxx xxxx uuuu uuuu
14h
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
15h
Capture/Compare/PWM1 (LSB)
Capture/Compare/PWM1 (MSB)
16h
xxxx xxxx uuuu uuuu
17h
—
—
CCP1X
CCP1Y
CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
Unimplemented
18h-1Fh
—
—
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from either bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: The BOR bit is reserved on the PIC16C62, always maintain this bit set.
5: The IRP and RP1 bits are reserved on the PIC16C62/62A/R62, always maintain these bits clear.
6: PIE1<7:6> and PIR1<7:6> are reserved on the PIC16C62/62A/R62, always maintain these bits clear.
DS30234D-page 24
1997 Microchip Technology Inc.
PIC16C6X
TABLE 4-2:
Address Name
Bank 1
SPECIAL FUNCTION REGISTERS FOR THE PIC16C62/62A/R62 (Cont.’d)
Value on:
POR,
BOR
Value on
all other
resets(3)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
80h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
0000 0000 0000 0000
1111 1111 1111 1111
0000 0000 0000 0000
0001 1xxx 000q quuu
81h
OPTION
RBPU
Program Counter's (PC) Least Significant Byte
RP0 TO
Indirect data memory address pointer
PORTA Data Direction Register
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
82h(1)
83h(1)
PCL
IRP(5)
RP1(5)
STATUS
PD
Z
DC
C
84h(1)
85h
86h
87h
88h
89h
FSR
xxxx xxxx uuuu uuuu
--11 1111 --11 1111
1111 1111 1111 1111
1111 1111 1111 1111
TRISA
TRISB
TRISC
—
—
—
PORTB Data Direction Register
PORTC Data Direction Register
Unimplemented
—
—
—
—
—
Unimplemented
8Ah(1,2)
Write Buffer for the upper 5 bits of the Program Counter
PCLATH
—
GIE
(6)
—
PEIE
(6)
—
T0IE
—
---0 0000 ---0 0000
0000 000x 0000 000u
8Bh(1)
8Ch
8Dh
8Eh
INTCON
PIE1
—
INTE
—
RBIE
T0IF
INTF
RBIF
SSPIE
CCP1IE
TMR2IE
TMR1IE 00-- 0000 00-- 0000
Unimplemented
—
—
—
BOR(4)
PCON
—
—
—
—
—
—
POR
---- --qq ---- --uu
8Fh
Unimplemented
Unimplemented
Unimplemented
—
—
—
—
—
—
90h
—
91h
—
92h
PR2
Timer2 Period Register
Synchronous Serial Port (I2C mode) Address Register
1111 1111 1111 1111
0000 0000 0000 0000
--00 0000 --00 0000
93h
SSPADD
SSPSTAT
—
94h
—
—
D/A
P
S
R/W
UA
BF
95h-9Fh
Unimplemented
—
—
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from either bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: The BOR bit is reserved on the PIC16C62, always maintain this bit set.
5: The IRP and RP1 bits are reserved on the PIC16C62/62A/R62, always maintain these bits clear.
6: PIE1<7:6> and PIR1<7:6> are reserved on the PIC16C62/62A/R62, always maintain these bits clear.
1997 Microchip Technology Inc.
DS30234D-page 25
PIC16C6X
TABLE 4-3:
SPECIAL FUNCTION REGISTERS FOR THE PIC16C63/R63
Value on:
POR,
BOR
Value on
all other
resets(3)
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Bank 0
00h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
Timer0 module’s register
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
0000 0000 0000 0000
0001 1xxx 000q quuu
01h
TMR0
PCL
02h(1)
03h(1)
Program Counter's (PC) Least Significant Byte
IRP(4)
RP1(4)
STATUS
RP0
Indirect data memory address pointer
PORTA Data Latch when written: PORTA pins when read
TO
PD
Z
DC
C
04h(1)
05h
06h
07h
08h
09h
FSR
xxxx xxxx uuuu uuuu
--xx xxxx --uu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
PORTA
PORTB
PORTC
—
—
—
PORTB Data Latch when written: PORTB pins when read
PORTC Data Latch when written: PORTC pins when read
Unimplemented
—
—
—
—
—
Unimplemented
0Ah(1,2)
0Bh(1)
0Ch
Write Buffer for the upper 5 bits of the Program Counter
PCLATH
—
GIE
(5)
—
—
PEIE
(5)
—
---0 0000 ---0 0000
0000 000x 0000 000u
INTCON
PIR1
T0IE
INTE
RBIE
SSPIF
—
T0IF
CCP1IF
—
INTF
TMR2IF
—
RBIF
TMR1IF 0000 0000 0000 0000
RCIF
—
TXIF
—–
—
CCP2IF ---- ---0 ---- ---0
xxxx xxxx uuuu uuuu
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
PIR2
TMR1L
TMR1H
T1CON
TMR2
Holding register for the Least Significant Byte of the 16-bit TMR1 register
Holding register for the Most Significant Byte of the 16-bit TMR1 register
xxxx xxxx uuuu uuuu
—
—
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu
Timer2 module’s register
0000 0000 0000 0000
T2CON
SSPBUF
SSPCON
CCPR1L
CCPR1H
CCP1CON
—
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000
Synchronous Serial Port Receive Buffer/Transmit Register
xxxx xxxx uuuu uuuu
SSPM0 0000 0000 0000 0000
xxxx xxxx uuuu uuuu
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
Capture/Compare/PWM1 (LSB)
Capture/Compare/PWM1 (MSB)
xxxx xxxx uuuu uuuu
—
—
CCP1X
SREN
CCP1Y
CREN
CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
SPEN
RX9
—
FERR
OERR
RX9D
0000 -00x 0000 -00x
0000 0000 0000 0000
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
18h
RCSTA
USART Transmit Data Register
USART Receive Data Register
Capture/Compare/PWM2 (LSB)
Capture/Compare/PWM2 (MSB)
19h
TXREG
RCREG
CCPR2L
CCPR2H
1Ah
1Bh
1Ch
1Dh
—
—
CCP2X
CCP2Y
CCP2M3 CCP2M2 CCP2M1 CCP2M0 --00 0000 --00 0000
CCP2CON
—
Unimplemented
1Eh-1Fh
—
—
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from either bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: The IRP and RP1 bits are reserved on the PIC16C63/R63, always maintain these bits clear.
5: PIE1<7:6> and PIR1<7:6> are reserved on the PIC16C63/R63, always maintain these bits clear.
1997 Microchip Technology Inc.
DS30234D-page 26
PIC16C6X
TABLE 4-3:
Address Name
Bank 1
SPECIAL FUNCTION REGISTERS FOR THE PIC16C63/R63 (Cont.’d)
Value on:
Value on
all other
resets(3)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
POR,
BOR
80h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
0000 0000 0000 0000
1111 1111 1111 1111
0000 0000 0000 0000
0001 1xxx 000q quuu
81h
OPTION
RBPU
Program Counter's (PC) Least Significant Byte
RP0 TO
Indirect data memory address pointer
PORTA Data Direction Register
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
82h(1)
83h(1)
PCL
IRP(4)
RP1(4)
STATUS
PD
Z
DC
C
84h(1)
85h
86h
87h
88h
89h
FSR
xxxx xxxx uuuu uuuu
--11 1111 --11 1111
1111 1111 1111 1111
1111 1111 1111 1111
TRISA
TRISB
TRISC
—
—
—
PORTB Data Direction Register
PORTC Data Direction Register
Unimplemented
—
—
—
—
—
Unimplemented
8Ah(1,2)
8Bh(1)
8Ch
Write Buffer for the upper 5 bits of the Program Counter
PCLATH
—
GIE
(5)
—
—
PEIE
(5)
—
---0 0000 ---0 0000
0000 000x 0000 000u
INTCON
PIE1
T0IE
INTE
RBIE
SSPIE
—
T0IF
CCP1IE
—
INTF
TMR2IE
—
RBIF
TMR1IE 0000 0000 0000 0000
CCP2IE ---- ---0 ---- ---0
RCIE
—
TXIE
—
—
8Dh
8Eh
8Fh
90h
91h
92h
93h
94h
95h
96h
97h
PIE2
PCON
—
—
—
—
—
—
—
POR
BOR
---- --qq ---- --uu
Unimplemented
—
—
—
—
—
—
—
Unimplemented
—
Unimplemented
PR2
SSPADD
SSPSTAT
—
Timer2 Period Register
1111 1111 1111 1111
0000 0000 0000 0000
--00 0000 --00 0000
Synchronous Serial Port (I2C mode) Address Register
—
—
D/A
P
S
R/W
UA
BF
Unimplemented
Unimplemented
Unimplemented
CSRC
—
—
—
—
—
—
—
—
98h(2)
TXSTA
TX9
TXEN
SYNC
—
BRGH
TRMT
TX9D
0000 -010 0000 -010
0000 0000 0000 0000
99h(2)
9Ah
9Bh
9Ch
9Dh
9Eh
9Fh
SPBRG
—
Baud Rate Generator Register
Unimplemented
—
—
—
—
—
—
—
—
—
—
—
—
—
Unimplemented
—
Unimplemented
—
Unimplemented
—
Unimplemented
—
Unimplemented
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from either bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: The IRP and RP1 bits are reserved on the PIC16C63/R63, always maintain these bits clear.
5: PIE1<7:6> and PIR1<7:6> are reserved on the PIC16C63/R63, always maintain these bits clear.
1997 Microchip Technology Inc.
DS30234D-page 27
PIC16C6X
TABLE 4-4:
SPECIAL FUNCTION REGISTERS FOR THE PIC16C64/64A/R64
Value on:
POR,
BOR
Value on
all other
resets(3)
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Bank 0
00h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
Timer0 module’s register
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
0000 0000 0000 0000
0001 1xxx 000q quuu
01h
TMR0
PCL
02h(1)
03h(1)
Program Counter's (PC) Least Significant Byte
IRP(5)
RP1(5)
STATUS
RP0
Indirect data memory address pointer
PORTA Data Latch when written: PORTA pins when read
TO
PD
Z
DC
C
04h(1)
05h
FSR
xxxx xxxx uuuu uuuu
--xx xxxx --uu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
PORTA
PORTB
PORTC
—
—
06h
PORTB Data Latch when written: PORTB pins when read
PORTC Data Latch when written: PORTC pins when read
PORTD Data Latch when written: PORTD pins when read
07h
08h
PORTD
PORTE
PCLATH
INTCON
09h
—
—
—
—
—
—
—
—
RE2
RE1
RE0
---- -xxx ---- -uuu
---0 0000 ---0 0000
0000 000x 0000 000u
0Ah(1,2)
Write Buffer for the upper 5 bits of the Program Counter
0Bh(1)
0Ch
0Dh
0Eh
0Fh
GIE
PSPIF
PEIE
(6)
T0IE
—
INTE
—
RBIE
T0IF
INTF
RBIF
PIR1
SSPIF
CCP1IF
TMR2IF
TMR1IF 00-- 0000 00-- 0000
—
Unimplemented
—
—
TMR1L
TMR1H
T1CON
TMR2
Holding register for the Least Significant Byte of the 16-bit TMR1 register
Holding register for the Most Significant Byte of the 16-bit TMR1 register
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
10h
—
—
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu
11h
Timer2 module’s register
0000 0000 0000 0000
12h
T2CON
SSPBUF
SSPCON
CCPR1L
CCPR1H
CCP1CON
—
—
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000
13h
Synchronous Serial Port Receive Buffer/Transmit Register
xxxx xxxx uuuu uuuu
SSPM0 0000 0000 0000 0000
xxxx xxxx uuuu uuuu
14h
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
15h
Capture/Compare/PWM1 (LSB)
Capture/Compare/PWM1 (MSB)
16h
xxxx xxxx uuuu uuuu
17h
—
—
CCP1X
CCP1Y
CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
Unimplemented
18h-1Fh
—
—
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from either bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: The BOR bit is reserved on the PIC16C64, always maintain this bit set.
5: The IRP and RP1 bits are reserved on the PIC16C64/64A/R64, always maintain these bits clear.
6: PIE1<6> and PIR1<6> are reserved on the PIC16C64/64A/R64, always maintain these bits clear.
DS30234D-page 28
1997 Microchip Technology Inc.
PIC16C6X
TABLE 4-4:
Address Name
Bank 1
SPECIAL FUNCTION REGISTERS FOR THE PIC16C64/64A/R64 (Cont.’d)
Value on:
POR,
BOR
Value on
all other
resets(3)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
80h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
0000 0000 0000 0000
1111 1111 1111 1111
0000 0000 0000 0000
0001 1xxx 000q quuu
81h
OPTION
RBPU
Program Counter's (PC) Least Significant Byte
RP0 TO
Indirect data memory address pointer
PORTA Data Direction Register
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
82h(1)
83h(1)
PCL
IRP(5)
RP1(5)
STATUS
PD
Z
DC
C
84h(1)
85h
FSR
xxxx xxxx uuuu uuuu
--11 1111 --11 1111
1111 1111 1111 1111
1111 1111 1111 1111
1111 1111 1111 1111
TRISA
TRISB
TRISC
—
—
86h
PORTB Data Direction Register
PORTC Data Direction Register
PORTD Data Direction Register
87h
88h
TRISD
IBF
—
OBF
—
IBOV
—
PSPMODE
—
PORTE Data Direction Bits
0000 -111 0000 -111
---0 0000 ---0 0000
0000 000x 0000 000u
89h
TRISE
8Ah(1,2)
Write Buffer for the upper 5 bits of the Program Counter
PCLATH
INTCON
8Bh(1)
8Ch
8Dh
8Eh
GIE
PEIE
(6)
T0IE
—
INTE
—
RBIE
T0IF
INTF
RBIF
PIE1
—
SSPIE
CCP1IE
TMR2IE
TMR1IE 00-- 0000 00-- 0000
PSPIE
Unimplemented
—
—
—
BOR(4)
PCON
—
—
—
—
—
—
POR
---- --qq ---- --uu
8Fh
Unimplemented
Unimplemented
Unimplemented
—
—
—
—
—
—
90h
—
91h
—
92h
PR2
SSPADD
SSPSTAT
—
Timer2 Period Register
Synchronous Serial Port (I2C mode) Address Register
1111 1111 1111 1111
0000 0000 0000 0000
--00 0000 --00 0000
93h
94h
—
—
D/A
P
S
R/W
UA
BF
95h-9Fh
Unimplemented
—
—
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from either bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: The BOR bit is reserved on the PIC16C64, always maintain this bit set.
5: The IRP and RP1 bits are reserved on the PIC16C64/64A/R64, always maintain these bits clear.
6: PIE1<6> and PIR1<6> are reserved on the PIC16C64/64A/R64, always maintain these bits clear.
1997 Microchip Technology Inc.
DS30234D-page 29
PIC16C6X
TABLE 4-5:
SPECIAL FUNCTION REGISTERS FOR THE PIC16C65/65A/R65
Value on:
POR,
BOR
Value on
all other
resets(3)
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Bank 0
00h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
Timer0 module’s register
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
0000 0000 0000 0000
0001 1xxx 000q quuu
01h
TMR0
PCL
02h(1)
03h(1)
Program Counter's (PC) Least Significant Byte
IRP(5)
RP1(5)
STATUS
RP0
Indirect data memory address pointer
PORTA Data Latch when written: PORTA pins when read
TO
PD
Z
DC
C
04h(1)
05h
FSR
xxxx xxxx uuuu uuuu
--xx xxxx --uu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
PORTA
PORTB
PORTC
—
—
06h
PORTB Data Latch when written: PORTB pins when read
PORTC Data Latch when written: PORTC pins when read
PORTD Data Latch when written: PORTD pins when read
07h
08h
PORTD
PORTE
PCLATH
INTCON
PIR1
09h
—
—
—
—
—
—
—
—
RE2
RE1
RE0
---- -xxx ---- -uuu
---0 0000 ---0 0000
0000 000x 0000 000u
0Ah(1,2)
0Bh(1)
0Ch
Write Buffer for the upper 5 bits of the Program Counter
GIE
PEIE
(6)
T0IE
INTE
RBIE
SSPIF
—
T0IF
CCP1IF
—
INTF
TMR2IF
—
RBIF
TMR1IF 0000 0000 0000 0000
PSPIF
—
RCIF
—
TXIF
—–
—
CCP2IF ---- ---0 ---- ---0
xxxx xxxx uuuu uuuu
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
PIR2
TMR1L
TMR1H
T1CON
TMR2
Holding register for the Least Significant Byte of the 16-bit TMR1 register
Holding register for the Most Significant Byte of the 16-bit TMR1 register
xxxx xxxx uuuu uuuu
—
—
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu
Timer2 module’s register
0000 0000 0000 0000
T2CON
SSPBUF
SSPCON
CCPR1L
CCPR1H
CCP1CON
—
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000
Synchronous Serial Port Receive Buffer/Transmit Register
xxxx xxxx uuuu uuuu
SSPM0 0000 0000 0000 0000
xxxx xxxx uuuu uuuu
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
Capture/Compare/PWM1 (LSB)
Capture/Compare/PWM1 (MSB)
xxxx xxxx uuuu uuuu
—
—
CCP1X
SREN
CCP1Y
CREN
CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
SPEN
RX9
—
FERR
OERR
RX9D
0000 -00x 0000 -00x
0000 0000 0000 0000
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
18h
RCSTA
USART Transmit Data Register
USART Receive Data Register
Capture/Compare/PWM2 (LSB)
Capture/Compare/PWM2 (MSB)
19h
TXREG
RCREG
CCPR2L
CCPR2H
1Ah
1Bh
1Ch
1Dh
—
—
CCP2X
CCP2Y
CCP2M3 CCP2M2 CCP2M1 CCP2M0 --00 0000 --00 0000
CCP2CON
—
Unimplemented
1Eh-1Fh
—
—
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from either bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: The BOR bit is reserved on the PIC16C65, always maintain this bit set.
5: The IRP and RP1 bits are reserved on the PIC16C65/65A/R65, always maintain these bits clear.
6: PIE1<6> and PIR1<6> are reserved on the PIC16C65/65A/R65, always maintain these bits clear.
DS30234D-page 30
1997 Microchip Technology Inc.
PIC16C6X
TABLE 4-5:
Address Name
Bank 1
SPECIAL FUNCTION REGISTERS FOR THE PIC16C65/65A/R65 (Cont.’d)
Value on:
POR,
BOR
Value on
all other
resets(3)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
80h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
0000 0000 0000 0000
1111 1111 1111 1111
0000 0000 0000 0000
0001 1xxx 000q quuu
81h
OPTION
RBPU
Program Counter's (PC) Least Significant Byte
RP0 TO
Indirect data memory address pointer
PORTA Data Direction Register
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
82h(1)
83h(1)
PCL
IRP(5)
RP1(5)
STATUS
PD
Z
DC
C
84h(1)
85h
FSR
xxxx xxxx uuuu uuuu
--11 1111 --11 1111
1111 1111 1111 1111
1111 1111 1111 1111
1111 1111 1111 1111
TRISA
TRISB
TRISC
—
—
86h
PORTB Data Direction Register
PORTC Data Direction Register
PORTD Data Direction Register
87h
88h
TRISD
TRISE
PCLATH
INTCON
PIE1
IBF
—
OBF
—
IBOV
—
PSPMODE
—
PORTE Data Direction Bits
0000 -111 0000 -111
---0 0000 ---0 0000
0000 000x 0000 000u
89h
8Ah(1,2)
8Bh(1)
8Ch
Write Buffer for the upper 5 bits of the Program Counter
GIE
PEIE
(6)
T0IE
INTE
RBIE
SSPIE
—
T0IF
CCP1IE
—
INTF
TMR2IE
—
RBIF
TMR1IE 0000 0000 0000 0000
CCP2IE ---- ---0 ---- ---0
PSPIE
—
RCIE
—
TXIE
—
—
8Dh
8Eh
8Fh
90h
91h
92h
93h
94h
95h
96h
97h
PIE2
PCON
—
BOR(4)
—
—
—
—
—
—
POR
---- --qq ---- --uu
Unimplemented
—
—
—
—
—
—
—
Unimplemented
—
Unimplemented
PR2
SSPADD
SSPSTAT
—
Timer2 Period Register
1111 1111 1111 1111
0000 0000 0000 0000
--00 0000 --00 0000
Synchronous Serial Port (I2C mode) Address Register
—
—
D/A
P
S
R/W
UA
BF
Unimplemented
Unimplemented
Unimplemented
CSRC
—
—
—
—
—
—
—
—
TX9
TXEN
SYNC
—
BRGH
TRMT
TX9D
0000 -010 0000 -010
0000 0000 0000 0000
98h
TXSTA
Baud Rate Generator Register
Unimplemented
99h
9Ah
9Bh
9Ch
9Dh
9Eh
9Fh
SPBRG
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Unimplemented
—
Unimplemented
—
Unimplemented
—
Unimplemented
—
Unimplemented
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from either bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: The BOR bit is reserved on the PIC16C65, always maintain this bit set.
5: The IRP and RP1 bits are reserved on the PIC16C65/65A/R65, always maintain these bits clear.
6: PIE1<6> and PIR1<6> are reserved on the PIC16C65/65A/R65, always maintain these bits clear.
1997 Microchip Technology Inc.
DS30234D-page 31
PIC16C6X
TABLE 4-6:
SPECIAL FUNCTION REGISTERS FOR THE PIC16C66/67
Value on:
POR,
BOR
Value on
all other
resets(3)
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Bank 0
00h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
Timer0 module’s register
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
0000 0000 0000 0000
0001 1xxx 000q quuu
01h
TMR0
PCL
02h(1)
03h(1)
Program Counter's (PC) Least Significant Byte
STATUS
IRP
Indirect data memory address pointer
PORTA Data Latch when written: PORTA pins when read
RP1
RP0
TO
PD
Z
DC
C
04h(1)
05h
FSR
xxxx xxxx uuuu uuuu
--xx xxxx --uu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
PORTA
PORTB
PORTC
—
—
06h
PORTB Data Latch when written: PORTB pins when read
PORTC Data Latch when written: PORTC pins when read
PORTD Data Latch when written: PORTD pins when read
07h
08h(5)
09h(5)
0Ah(1,2)
0Bh(1)
0Ch
PORTD
PORTE
PCLATH
INTCON
PIR1
—
—
—
—
—
—
—
—
RE2
RE1
RE0
---- -xxx ---- -uuu
---0 0000 ---0 0000
0000 000x 0000 000u
Write Buffer for the upper 5 bits of the Program Counter
GIE
PEIE
(4)
T0IE
INTE
RBIE
SSPIF
—
T0IF
CCP1IF
—
INTF
TMR2IF
—
RBIF
PSPIF(6)
—
RCIF
—
TXIF
—–
TMR1IF 0000 0000 0000 0000
—
CCP2IF ---- ---0 ---- ---0
xxxx xxxx uuuu uuuu
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
PIR2
TMR1L
TMR1H
T1CON
TMR2
Holding register for the Least Significant Byte of the 16-bit TMR1 register
Holding register for the Most Significant Byte of the 16-bit TMR1 register
xxxx xxxx uuuu uuuu
—
—
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu
Timer2 module’s register
0000 0000 0000 0000
T2CON
SSPBUF
SSPCON
CCPR1L
CCPR1H
CCP1CON
—
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000
Synchronous Serial Port Receive Buffer/Transmit Register
xxxx xxxx uuuu uuuu
SSPM0 0000 0000 0000 0000
xxxx xxxx uuuu uuuu
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
Capture/Compare/PWM1 (LSB)
Capture/Compare/PWM1 (MSB)
xxxx xxxx uuuu uuuu
—
—
CCP1X
SREN
CCP1Y
CREN
CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
SPEN
RX9
—
FERR
OERR
RX9D
0000 -00x 0000 -00x
0000 0000 0000 0000
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
18h
RCSTA
USART Transmit Data Register
USART Receive Data Register
Capture/Compare/PWM2 (LSB)
Capture/Compare/PWM2 (MSB)
19h
TXREG
RCREG
CCPR2L
CCPR2H
1Ah
1Bh
1Ch
1Dh
—
—
CCP2X
CCP2Y
CCP2M3 CCP2M2 CCP2M1 CCP2M0 --00 0000 --00 0000
CCP2CON
—
Unimplemented
1Eh-1Fh
—
—
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from any bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: PIE1<6> and PIR1<6> are reserved on the PIC16C66/67, always maintain these bits clear.
5: PORTD, PORTE, TRISD, and TRISE are not implemented on the PIC16C66, read as '0'.
6: PSPIF (PIR1<7>) and PSPIE (PIE1<7>) are reserved on the PIC16C66, maintain these bits clear.
DS30234D-page 32
1997 Microchip Technology Inc.
PIC16C6X
TABLE 4-6:
Address Name
Bank 1
SPECIAL FUNCTION REGISTERS FOR THE PIC16C66/67 (Cont.’d)
Value on:
POR,
BOR
Value on
all other
resets(3)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
80h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
0000 0000 0000 0000
1111 1111 1111 1111
0000 0000 0000 0000
0001 1xxx 000q quuu
81h
OPTION
RBPU
Program Counter's (PC) Least Significant Byte
RP0 TO
Indirect data memory address pointer
PORTA Data Direction Register
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
82h(1)
83h(1)
PCL
STATUS
PD
Z
DC
C
IRP
RP1
84h(1)
85h
FSR
xxxx xxxx uuuu uuuu
--11 1111 --11 1111
1111 1111 1111 1111
1111 1111 1111 1111
1111 1111 1111 1111
TRISA
TRISB
TRISC
—
—
86h
PORTB Data Direction Register
PORTC Data Direction Register
PORTD Data Direction Register
87h
88h(5)
89h(5)
8Ah(1,2)
8Bh(1)
8Ch
TRISD
TRISE
PCLATH
INTCON
PIE1
IBF
—
OBF
—
IBOV
—
PSPMODE
—
PORTE Data Direction Bits
0000 -111 0000 -111
---0 0000 ---0 0000
0000 000x 0000 000u
Write Buffer for the upper 5 bits of the Program Counter
GIE
PEIE
(4)
T0IE
INTE
RBIE
SSPIE
—
T0IF
CCP1IE
—
INTF
TMR2IE
—
RBIF
PSPIE(6)
RCIE
—
TXIE
—
TMR1IE 0000 0000 0000 0000
CCP2IE ---- ---0 ---- ---0
—
—
—
8Dh
8Eh
8Fh
90h
91h
92h
93h
94h
95h
96h
97h
PIE2
PCON
—
—
—
—
—
—
POR
---- --qq ---- --uu
BOR
Unimplemented
—
—
—
—
—
—
—
Unimplemented
—
Unimplemented
PR2
SSPADD
SSPSTAT
—
Timer2 Period Register
1111 1111 1111 1111
0000 0000 0000 0000
0000 0000 0000 0000
Synchronous Serial Port (I2C mode) Address Register
SMP
CKE
D/A
P
S
R/W
UA
BF
Unimplemented
Unimplemented
Unimplemented
CSRC
—
—
—
—
—
—
—
—
TX9
TXEN
SYNC
—
BRGH
TRMT
TX9D
0000 -010 0000 -010
0000 0000 0000 0000
98h
TXSTA
Baud Rate Generator Register
Unimplemented
99h
9Ah
9Bh
9Ch
9Dh
9Eh
9Fh
SPBRG
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Unimplemented
—
Unimplemented
—
Unimplemented
—
Unimplemented
—
Unimplemented
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from any bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: PIE1<6> and PIR1<6> are reserved on the PIC16C66/67, always maintain these bits clear.
5: PORTD, PORTE, TRISD, and TRISE are not implemented on the PIC16C66, read as '0'.
6: PSPIF (PIR1<7>) and PSPIE (PIE1<7>) are reserved on the PIC16C66, maintain these bits clear.
1997 Microchip Technology Inc.
DS30234D-page 33
PIC16C6X
TABLE 4-6:
Address Name
Bank 2
SPECIAL FUNCTION REGISTERS FOR THE PIC16C66/67 (Cont.’d)
Value on:
POR,
BOR
Value on
all other
resets(3)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
100h(1)
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
Timer0 module’s register
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
0000 0000 0000 0000
0001 1xxx 000q quuu
xxxx xxxx uuuu uuuu
101h
TMR0
PCL
102h(1)
103h(1)
Program Counter's (PC) Least Significant Byte
STATUS
RP0
TO
PD
Z
DC
C
IRP
RP1
104h(1)
105h
106h
107h
108h
109h
FSR
—
Indirect data memory address pointer
Unimplemented
—
—
PORTB
—
PORTB Data Latch when written: PORTB pins when read
xxxx xxxx uuuu uuuu
Unimplemented
Unimplemented
Unimplemented
—
—
—
—
—
—
—
—
10Ah(1,2)
10Bh(1)
Write Buffer for the upper 5 bits of the Program Counter
INTE RBIE T0IF INTF RBIF
PCLATH
—
—
—
---0 0000 ---0 0000
0000 000x 0000 000u
INTCON
—
GIE
PEIE
T0IE
10Ch-
10Fh
Unimplemented
—
—
Bank 3
180h(1)
181h
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
0000 0000 0000 0000
1111 1111 1111 1111
0000 0000 0000 0000
0001 1xxx 000q quuu
xxxx xxxx uuuu uuuu
OPTION
PCL
RBPU
Program Counter's (PC) Least Significant Byte
RP0 TO
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
182h(1)
183h(1)
STATUS
PD
Z
DC
C
IRP
RP1
184h(1)
185h
186h
187h
188h
189h
FSR
—
Indirect data memory address pointer
Unimplemented
—
—
TRISB
—
PORTB Data Direction Register
Unimplemented
1111 1111 1111 1111
—
—
—
—
—
—
—
Unimplemented
—
Unimplemented
18Ah(1,2)
18Bh(1)
Write Buffer for the upper 5 bits of the Program Counter
INTE RBIE T0IF INTF RBIF
PCLATH
—
—
—
---0 0000 ---0 0000
0000 000x 0000 000u
INTCON
—
GIE
PEIE
T0IE
18Ch-
19Fh
Unimplemented
—
—
Legend: x= unknown, u= unchanged, q= value depends on condition, -= unimplemented location read as '0'.
Shaded locations are unimplemented, read as ‘0’.
Note 1: These registers can be addressed from any bank.
2: The upper byte of the Program Counter (PC) is not directly accessible. PCLATH is a holding register for the PC whose
contents are transferred to the upper byte of the program counter. (PC<12:8>)
3: Other (non power-up) resets include external reset through MCLR and the Watchdog Timer reset.
4: PIE1<6> and PIR1<6> are reserved on the PIC16C66/67, always maintain these bits clear.
5: PORTD, PORTE, TRISD, and TRISE are not implemented on the PIC16C66, read as '0'.
6: PSPIF (PIR1<7>) and PSPIE (PIE1<7>) are reserved on the PIC16C66, maintain these bits clear.
DS30234D-page 34
1997 Microchip Technology Inc.
PIC16C6X
4.2.2.1
STATUS REGISTER
It is recommended, therefore, that only BCF, BSF,
SWAPF and MOVWF instructions are used to alter the
STATUS register because these instructions do not
affect the Z, C or DC bits from the STATUS register. For
other instructions, not affecting any status bits, see the
“Instruction Set Summary.”
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The STATUS register, shown in Figure 4-9, contains the
arithmetic status of the ALU, the RESET status and the
bank select bits for data memory.
Note 1: For those devices that do not use bits IRP
and RP1 (STATUS<7:6>), maintain these
bits clear to ensure upward compatibility
with future products.
The STATUS register can be the destination for any
instruction, as with any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to the
device logic. Furthermore, the TO and PD bits are not
writable. Therefore, the result of an instruction with the
STATUS register as destination may be different than
intended.
Note 2: The C and DC bits operate as a borrow
and digit borrow bit, respectively, in sub-
traction. See the SUBLW and SUBWF
instructions for examples.
For example, CLRF STATUSwill clear the upper-three
bits and set the Z bit. This leaves the STATUS register
as 000u u1uu(where u= unchanged).
FIGURE 4-9: STATUS REGISTER (ADDRESS 03h, 83h, 103h, 183h)
R/W-0
IRP
R/W-0
RP1
R/W-0
RP0
R-1
TO
R-1
PD
R/W-x
Z
R/W-x
DC
R/W-x
C
R = Readable bit
W = Writable bit
- n = Value at POR reset
bit7
bit0
x
= unknown
bit 7:
IRP: RegIster Bank Select bit (used for indirect addressing)
1 = Bank 2, 3 (100h - 1FFh)
0 = Bank 0, 1 (00h - FFh)
bit 6-5: RP1:RP0: Register Bank Select bits (used for direct addressing)
11 = Bank 3 (180h - 1FFh)
10 = Bank 2 (100h - 17Fh)
01 = Bank 1 (80h - FFh)
00 = Bank 0 (00h - 7Fh)
Each bank is 128 bytes.
bit 4:
bit 3:
bit 2:
bit 1:
bit 0:
TO: Time-out bit
1 = After power-up, CLRWDTinstruction, or SLEEPinstruction
0 = A WDT time-out occurred
PD: Power-down bit
1 = After power-up or by the CLRWDTinstruction
0 = By execution of the SLEEPinstruction
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
DC: Digit carry/borrow bit (for ADDWF, ADDLW,SUBLW, and SUBWFinstructions) (For borrow the polarity is reversed).
1 = A carry-out from the 4th low order bit of the result occurred
0 = No carry-out from the 4th low order bit of the result
C: Carry/borrow bit (for ADDWF, ADDLW,SUBLW, and SUBWFinstructions)( For borrow the polarity is reversed).
1 = A carry-out from the most significant bit of the result occurred
0 = No carry-out from the most significant bit of the result
Note: a subtraction is executed by adding the two’s complement of the second operand.
For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of the source register.
1997 Microchip Technology Inc.
DS30234D-page 35
PIC16C6X
4.2.2.2
OPTION REGISTER
Note: To achieve a 1:1 prescaler assignment for
TMR0 register, assign the prescaler to the
Watchdog Timer.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The OPTION register is a readable and writable regis-
ter which contains various control bits to configure the
TMR0/WDT prescaler, the external INT interrupt,
TMR0, and the weak pull-ups on PORTB.
FIGURE 4-10: OPTION REGISTER (ADDRESS 81h, 181h)
R/W-1
RBPU
R/W-1
R/W-1
T0CS
R/W-1
T0SE
R/W-1
PSA
R/W-1
PS2
R/W-1
PS1
R/W-1
PS0
INTEDG
R
= Readable bit
W = Writable bit
bit7
bit0
U
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7:
RBPU: PORTB Pull-up Enable bit
1 = PORTB pull-ups are disabled
0 = PORTB pull-ups are enabled by individual port latch values
bit 6:
bit 5:
bit 4:
bit 3:
INTEDG: Interrupt Edge Select bit
1 = Interrupt on rising edge of RB0/INT pin
0 = Interrupt on falling edge of RB0/INT pin
T0CS: TMR0 Clock Source Select bit
1 = Transition on RA4/T0CKI pin
0 = Internal instruction cycle clock (CLKOUT)
T0SE: TMR0 Source Edge Select bit
1 = Increment on high-to-low transition on RA4/T0CKI pin
0 = Increment on low-to-high transition on RA4/T0CKI pin
PSA: Prescaler Assignment bit
1 = Prescaler is assigned to the WDT
0 = Prescaler is assigned to the Timer0 module
bit 2-0: PS2:PS0: Prescaler Rate Select bits
Bit Value
TMR0 Rate WDT Rate
000
001
010
011
100
101
110
111
1 : 1
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
1 : 256
DS30234D-page 36
1997 Microchip Technology Inc.
PIC16C6X
4.2.2.3
INTCON REGISTER
Note: Interrupt flag bits get set when an interrupt
condition occurs regardless of the state of
its corresponding enable bit or the global
enable bit, GIE (INTCON<7>).
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The INTCON Register is a readable and writable regis-
ter which contains the various enable and flag bits for
the TMR0 register overflow, RB port change and exter-
nal RB0/INT pin interrupts.
FIGURE 4-11: INTCON REGISTER (ADDRESS 0Bh, 8Bh, 10Bh 18Bh)
R/W-0
GIE
R/W-0
PEIE
R/W-0
T0IE
R/W-0
INTE
R/W-0
RBIE
R/W-0
T0IF
R/W-0
INTF
R/W-x
RBIF
R
= Readable bit
W = Writable bit
bit7
bit0
U
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
= unknown
x
(1)
bit 7:
GIE: Global Interrupt Enable bit
1 = Enables all un-masked interrupts
0 = Disables all interrupts
(2)
bit 6:
bit 5:
bit 4:
bit 3:
bit 2:
bit 1:
bit 0:
PEIE: Peripheral Interrupt Enable bit
1 = Enables all un-masked peripheral interrupts
0 = Disables all peripheral interrupts
T0IE: TMR0 Overflow Interrupt Enable bit
1 = Enables the TMR0 overflow interrupt
0 = Disables the TMR0 overflow interrupt
INTE: RB0/INT External Interrupt Enable bit
1 = Enables the RB0/INT external interrupt
0 = Disables the RB0/INT external interrupt
RBIE: RB Port Change Interrupt Enable bit
1 = Enables the RB port change interrupt
0 = Disables the RB port change interrupt
T0IF: TMR0 Overflow Interrupt Flag bit
1 = TMR0 register overflowed (must be cleared in software)
0 = TMR0 register did not overflow
INTF: RB0/INT External Interrupt Flag bit
1 = The RB0/INT external interrupt occurred (must be cleared in software)
0 = The RB0/INT external interrupt did not occur
RBIF: RB Port Change Interrupt Flag bit
1 = At least one of the RB7:RB4 pins changed state (see Section 5.2 to clear the interrupt)
0 = None of the RB7:RB4 pins have changed state
Note 1: For the PIC16C61/62/64/65, if an interrupt occurs while the GIE bit is being cleared, the GIE bit may unintentionally
be re-enabled by the RETFIEinstruction in the user’s Interrupt Service Routine. Refer to Section 13.5 for a detailed
description.
2: The PEIE bit (bit6) is unimplemented on the PIC16C61, read as '0'.
Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the
global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to
enabling an interrupt.
1997 Microchip Technology Inc.
DS30234D-page 37
PIC16C6X
4.2.2.4
PIE1 REGISTER
Note: Bit PEIE (INTCON<6>) must be set to
Applicable Devices
enable any peripheral interrupt.
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
This register contains the individual enable bits for the
peripheral interrupts.
FIGURE 4-12: PIE1 REGISTER FOR PIC16C62/62A/R62 (ADDRESS 8Ch)
RW-0
—
R/W-0
—
U-0
—
U-0
—
R/W-0
SSPIE
R/W-0
R/W-0
TMR2IE TMR1IE
bit0
R/W-0
CCP1IE
R
= Readable bit
W = Writable bit
U
bit7
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7-6: Reserved: Always maintain these bits clear.
bit 5-4: Unimplemented: Read as '0'
bit 3:
bit 2:
bit 1:
bit 0:
SSPIE: Synchronous Serial Port Interrupt Enable bit
1 = Enables the SSP interrupt
0 = Disables the SSP interrupt
CCP1IE: CCP1 Interrupt Enable bit
1 = Enables the CCP1 interrupt
0 = Disables the CCP1 interrupt
TMR2IE: TMR2 to PR2 Match Interrupt Enable bit
1 = Enables the TMR2 to PR2 match interrupt
0 = Disables the TMR2 to PR2 match interrupt
TMR1IE: TMR1 Overflow Interrupt Enable bit
1 = Enables the TMR1 overflow interrupt
0 = Disables the TMR1 overflow interrupt
DS30234D-page 38
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 4-13: PIE1 REGISTER FOR PIC16C63/R63/66 (ADDRESS 8Ch)
R/W-0
—
R/W-0
—
R/W-0
RCIE
R/W-0
TXIE
R/W-0
SSPIE
R/W-0
R/W-0
TMR2IE TMR1IE
bit0
R/W-0
CCP1IE
R
= Readable bit
W = Writable bit
U
bit7
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7-6: Reserved: Always maintain these bits clear.
bit 5:
RCIE: USART Receive Interrupt Enable bit
1 = Enables the USART receive interrupt
0 = Disables the USART receive interrupt
bit 4:
TXIE: USART Transmit Interrupt Enable bit
1 = Enables the USART transmit interrupt
0 = Disables the USART transmit interrupt
bit 3:
bit 2:
bit 1:
bit 0:
SSPIE: Synchronous Serial Port Interrupt Enable bit
1 = Enables the SSP interrupt
0 = Disables the SSP interrupt
CCP1IE: CCP1 Interrupt Enable bit
1 = Enables the CCP1 interrupt
0 = Disables the CCP1 interrupt
TMR2IE: TMR2 to PR2 Match Interrupt Enable bit
1 = Enables the TMR2 to PR2 match interrupt
0 = Disables the TMR2 to PR2 match interrupt
TMR1IE: TMR1 Overflow Interrupt Enable bit
1 = Enables the TMR1 overflow interrupt
0 = Disables the TMR1 overflow interrupt
FIGURE 4-14: PIE1 REGISTER FOR PIC16C64/64A/R64 (ADDRESS 8Ch)
R/W-0
PSPIE
R/W-0
—
U-0
—
U-0
—
R/W-0
SSPIE
R/W-0
R/W-0
TMR2IE TMR1IE
bit0
R/W-0
CCP1IE
R
= Readable bit
W = Writable bit
U
bit7
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7:
bit 6:
PSPIE: Parallel Slave Port Read/Write Interrupt Enable bit
1 = Enables the PSP read/write interrupt
0 = Disables the PSP read/write interrupt
Reserved: Always maintain this bit clear.
bit 5-4: Unimplemented: Read as '0'
bit 3:
bit 2:
bit 1:
bit 0:
SSPIE: Synchronous Serial Port Interrupt Enable bit
1 = Enables the SSP interrupt
0 = Disables the SSP interrupt
CCP1IE: CCP1 Interrupt Enable bit
1 = Enables the CCP1 interrupt
0 = Disables the CCP1 interrupt
TMR2IE: TMR2 to PR2 Match Interrupt Enable bit
1 = Enables the TMR2 to PR2 match interrupt
0 = Disables the TMR2 to PR2 match interrupt
TMR1IE: TMR1 Overflow Interrupt Enable bit
1 = Enables the TMR1 overflow interrupt
0 = Disables the TMR1 overflow interrupt
1997 Microchip Technology Inc.
DS30234D-page 39
PIC16C6X
FIGURE 4-15: PIE1 REGISTER FOR PIC16C65/65A/R65/67 (ADDRESS 8Ch)
R/W-0
PSPIE
R/W-0
—
R/W-0
RCIE
R/W-0
TXIE
R/W-0
SSPIE
R/W-0
R/W-0
TMR2IE TMR1IE
bit0
R/W-0
CCP1IE
R
= Readable bit
W = Writable bit
U
bit7
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7:
PSPIE: Parallel Slave Port Read/Write Interrupt Enable bit
1 = Enables the PSP read/write interrupt
0 = Disables the PSP read/write interrupt
bit 6:
bit 5:
Reserved: Always maintain this bit clear.
RCIE: USART Receive Interrupt Enable bit
1 = Enables the USART receive interrupt
0 = Disables the USART receive interrupt
bit 4:
TXIE: USART Transmit Interrupt Enable bit
1 = Enables the USART transmit interrupt
0 = Disables the USART transmit interrupt
bit 3:
bit 2:
bit 1:
bit 0:
SSPIE: Synchronous Serial Port Interrupt Enable bit
1 = Enables the SSP interrupt
0 = Disables the SSP interrupt
CCP1IE: CCP1 Interrupt Enable bit
1 = Enables the CCP1 interrupt
0 = Disables the CCP1 interrupt
TMR2IE: TMR2 to PR2 Match Interrupt Enable bit
1 = Enables the TMR2 to PR2 match interrupt
0 = Disables the TMR2 to PR2 match interrupt
TMR1IE: TMR1 Overflow Interrupt Enable bit
1 = Enables the TMR1 overflow interrupt
0 = Disables the TMR1 overflow interrupt
DS30234D-page 40
1997 Microchip Technology Inc.
PIC16C6X
4.2.2.5
PIR1 REGISTER
Note: Interrupt flag bits get set when an interrupt
condition occurs regardless of the state of
its corresponding enable bit or the global
enable bit, GIE (INTCON<7>). User soft-
ware should ensure the appropriate inter-
rupt flag bits are clear prior to enabling an
interrupt.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
This register contains the individual flag bits for the
peripheral interrupts.
FIGURE 4-16: PIR1 REGISTER FOR PIC16C62/62A/R62 (ADDRESS 0Ch)
R/W-0
—
R/W-0
—
U-0
—
U-0
—
R/W-0
SSPIF
R/W-0
R/W-0
TMR2IF TMR1IF
bit0
R/W-0
CCP1IF
R
= Readable bit
W = Writable bit
U
bit7
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7-6: Reserved: Always maintain these bits clear.
bit 5-4: Unimplemented: Read as '0'
bit 3:
SSPIF: Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
bit 2:
CCP1IF: CCP1 Interrupt Flag bit
Capture Mode
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare Mode
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM Mode
Unused in this mode
bit 1:
bit 0:
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflow occurred (must be cleared in software)
0 = No TMR1 register overflow occurred
Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the
global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to
enabling an interrupt.
1997 Microchip Technology Inc.
DS30234D-page 41
PIC16C6X
FIGURE 4-17: PIR1 REGISTER FOR PIC16C63/R63/66 (ADDRESS 0Ch)
R/W-0
—
R/W-0
—
R-0
R-0
R/W-0
SSPIF
R/W-0
R/W-0
TMR2IF TMR1IF
bit0
R/W-0
RCIF
TXIF
CCP1IF
R
= Readable bit
W = Writable bit
U
bit7
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7-6: Reserved: Always maintain these bits clear.
bit 5:
bit 4:
bit 3:
bit 2:
RCIF: USART Receive Interrupt Flag bit
1 = The USART receive buffer is full (cleared by reading RCREG)
0 = The USART receive buffer is empty
TXIF: USART Transmit Interrupt Flag bit
1 = The USART transmit buffer is empty (cleared by writing to TXREG)
0 = The USART transmit buffer is full
SSPIF: Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
CCP1IF: CCP1 Interrupt Flag bit
Capture Mode
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare Mode
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM Mode
Unused in this mode
bit 1:
bit 0:
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflow occurred (must be cleared in software)
0 = No TMR1 register overflow occurred
Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the
global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to
enabling an interrupt.
DS30234D-page 42
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 4-18: PIR1 REGISTER FOR PIC16C64/64A/R64 (ADDRESS 0Ch)
R/W-0
PSPIF
R/W-0
—
U-0
—
U-0
—
R/W-0
SSPIF
R/W-0
R/W-0
TMR2IF TMR1IF
bit0
R/W-0
CCP1IF
R
= Readable bit
W = Writable bit
U
bit7
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7:
PSPIF: Parallel Slave Port Interrupt Flag bit
1 = A read or a write operation has taken place (must be cleared in software)
0 = No read or write operation has taken place
bit 6:
Reserved: Always maintain this bit clear.
bit 5-4: Unimplemented: Read as '0'
bit 3:
SSPIF: Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
bit 2:
CCP1IF: CCP1 Interrupt Flag bit
Capture Mode
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare Mode
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM Mode
Unused in this mode
bit 1:
bit 0:
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflow occurred (must be cleared in software)
0 = No TMR1 register occurred
Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the
global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to
enabling an interrupt.
1997 Microchip Technology Inc.
DS30234D-page 43
PIC16C6X
FIGURE 4-19: PIR1 REGISTER FOR PIC16C65/65A/R65/67 (ADDRESS 0Ch)
R/W-0
PSPIF
R/W-0
—
R-0
R-0
R/W-0
SSPIF
R/W-0
R/W-0
TMR2IF TMR1IF
bit0
R/W-0
RCIF
TXIF
CCP1IF
R
= Readable bit
W = Writable bit
U
bit7
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7:
PSPIF: Parallel Slave Port Interrupt Flag bit
1 = A read or a write operation has taken place (must be cleared in software)
0 = No read or write operation has taken place
bit 6:
bit 5:
Reserved: Always maintain this bit clear.
RCIF: USART Receive Interrupt Flag bit
1 = The USART receive buffer is full (cleared by reading RCREG)
0 = The USART receive buffer is empty
bit 4:
bit 3:
bit 2:
TXIF: USART Transmit Interrupt Flag bit
1 = The USART transmit buffer is empty (cleared by writing to TXREG)
0 = The USART transmit buffer is full
SSPIF: Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
CCP1IF: CCP1 Interrupt Flag bit
Capture Mode
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare Mode
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM Mode
Unused in this mode
bit 1:
bit 0:
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflow occurred (must be cleared in software)
0 = No TMR1 register overflow occurred
Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the
global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to
enabling an interrupt.
DS30234D-page 44
1997 Microchip Technology Inc.
PIC16C6X
4.2.2.6
PIE2 REGISTER
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
This register contains the CCP2 interrupt enable bit.
FIGURE 4-20: PIE2 REGISTER (ADDRESS 8Dh)
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
CCP2IE
R
= Readable bit
W = Writable bit
bit7
bit0
U
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7-1: Unimplemented: Read as '0'
bit 0:
CCP2IE: CCP2 Interrupt Enable bit
1 = Enables the CCP2 interrupt
0 = Disables the CCP2 interrupt
1997 Microchip Technology Inc.
DS30234D-page 45
PIC16C6X
.
4.2.2.7
PIR2 REGISTER
Note: Interrupt flag bits get set when an interrupt
condition occurs regardless of the state of
its corresponding enable bit or the global
enable bit, GIE (INTCON<7>). User soft-
ware should ensure the appropriate inter-
rupt flag bits are clear prior to enabling an
interrupt.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
This register contains the CCP2 interrupt flag bit.
FIGURE 4-21: PIR2 REGISTER (ADDRESS 0Dh)
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
CCP2IF
R
= Readable bit
W = Writable bit
bit7
bit0
U
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7-1: Unimplemented: Read as '0'
bit 0:
CCP2IF: CCP2 Interrupt Flag bit
Capture Mode
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare Mode
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM Mode
Unused in this mode
Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the
global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to
enabling an interrupt.
DS30234D-page 46
1997 Microchip Technology Inc.
PIC16C6X
4.2.2.8
PCON REGISTER
Note: BOR is unknown on Power-on Reset. It
must then be set by the user and checked
on subsequent resets to see if BOR is
clear, indicating a brown-out has occurred.
The BOR status bit is a “don't care” and is
not necessarily predictable if the brown-out
circuit is disabled (by clearing the BODEN
bit in the Configuration word).
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The Power Control register (PCON) contains a flag bit
to allow differentiation between a Power-on Reset to an
external MCLR reset or WDT reset.Those devices with
brown-out detection circuitry contain an additional bit to
differentiate a Brown-out Reset condition from a
Power-on Reset condition.
FIGURE 4-22: PCON REGISTER FOR PIC16C62/64/65 (ADDRESS 8Eh)
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
POR
R/W-q
—
R
= Readable bit
W = Writable bit
bit7
bit0
U
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
= value depends on conditions
q
bit 7-2: Unimplemented: Read as '0'
bit 1:
POR: Power-on Reset Status bit
1 = No Power-on Reset occurred
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
bit 0:
Reserved
This bit should be set upon a Power-on Reset by user software and maintained as set. Use of this bit as a general
purpose read/write bit is not recommended, since this may affect upward compatibility with future products.
FIGURE 4-23: PCON REGISTER FOR PIC16C62A/R62/63/R63/64A/R64/65A/R65/66/67
(ADDRESS 8Eh)
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
POR
R/W-q
BOR
R
= Readable bit
W = Writable bit
bit7
bit0
U
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
= value depends on conditions
q
bit 7-2: Unimplemented: Read as '0'
bit 1:
POR: Power-on Reset Status bit
1 = No Power-on Reset occurred
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
bit 0:
BOR: Brown-out Reset Status bit
1 = No Brown-out Reset occurred
0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
1997 Microchip Technology Inc.
DS30234D-page 47
PIC16C6X
4.3
PCL and PCLATH
Note 1: There are no status bits to indicate stack
overflows or stack underflow conditions.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Note 2: There are no instructions mnemonics
called PUSH or POP. These are actions
that occur from the execution of theCALL,
RETURN, RETLW, and RETFIE instruc-
tions, or the vectoring to an interrupt
address
The program counter (PC) is 13-bits wide.The low byte
comes from the PCL register, which is a readable and
writable register. The upper bits (PC<12:8>) are not
readable, but are indirectly writable through the
PCLATH register. On any reset, the upper bits of the PC
will be cleared. Figure 4-24 shows the two situations for
the loading of the PC. The upper example in the figure
shows how the PC is loaded on a write to PCL
(PCLATH<4:0> → PCH). The lower example in the fig-
ure shows how the PC is loaded during aCALLor GOTO
instruction (PCLATH<4:3> → PCH).
4.4
Program Memory Paging
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X devices are capable of addressing a contin-
uous 8K word block of program memory.TheCALLand
GOTO instructions provide only 11 bits of address to
allow branching within any 2K program memory page.
When doing a CALLor GOTOinstruction the upper two
bits of the address are provided by PCLATH<4:3>.
When doing a CALLor GOTOinstruction, the user must
ensure that the page select bits are programmed so
that the desired program memory page is addressed. If
a return from a CALL instruction (or interrupt) is exe-
cuted, the entire 13-bit PC is pushed onto the stack.
Therefore, manipulation of the PCLATH<4:3> bits are
not required for the return instructions (which POPs the
address from the stack).
FIGURE 4-24: LOADING OF PC IN
DIFFERENT SITUATIONS
PCH
PCL
12
8
7
0
Instruction with
PCL as
PC
destination
8
PCLATH<4:0>
PCLATH
5
ALU
PCH
12 11 10
PCL
8
7
0
Note: PIC16C6X devices with 4K or less of pro-
gram memory ignore paging bit
PCLATH<4>.The use of PCLATH<4> as a
general purpose read/write bit is not rec-
ommended since this may affect upward
compatibility with future products.
GOTO, CALL
PC
11
PCLATH<4:3>
PCLATH
2
Opcode <10:0>
4.3.1
COMPUTED GOTO
A computed GOTO is accomplished by adding an offset
to the program counter (ADDWF PCL). When doing a
table read using a computed GOTO method, care
should be exercised if the table location crosses a PCL
memory boundary (each 256 word block). Refer to the
application note “Implementing a Table Read”(AN556).
4.3.2
STACK
The PIC16CXX family has an 8 deep x 13-bit wide
hardware stack. The stack space is not part of either
program or data space and the stack pointer is not
readable or writable. The PC is PUSHed onto the stack
when a CALL instruction is executed or an interrupt
causes a branch. The stack is POPed in the event of a
RETURN, RETLW or a RETFIE instruction execution.
PCLATH is not affected by a PUSH or a POP operation.
The stack operates as a circular buffer.This means that
after the stack has been PUSHed eight times, the ninth
push overwrites the value that was stored from the first
push. The tenth push overwrites the second push (and
so on).
DS30234D-page 48
1997 Microchip Technology Inc.
PIC16C6X
Example 4-1 shows the calling of a subroutine in
page 1 of the program memory.This example assumes
that the PCLATH is saved and restored by the interrupt
service routine (if interrupts are used).
4.5
Indirect Addressing, INDF and FSR
Registers
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The INDF register is not a physical register. Address-
ing the INDF register will cause indirect addressing.
EXAMPLE 4-1: CALL OF A SUBROUTINE IN
PAGE 1 FROM PAGE 0
Indirect addressing is possible by using the INDF reg-
ister. Any instruction using the INDF register actually
accesses the register pointed to by the File Select Reg-
ister, FSR. Reading the INDF register itself indirectly
(FSR = '0') will produce 00h. Writing to the INDF regis-
ter indirectly results in a no-operation (although status
bits may be affected). An effective 9-bit address is
obtained by concatenating the 8-bit FSR register and
the IRP bit (STATUS<7>), as shown in Figure 4-25.
ORG 0x500
BSF
BCF
PCLATH,3 ;Select page 1 (800h-FFFh)
PCLATH,4 ;Only on >4K devices
CALL
SUB1_P1
;Call subroutine in
;page 1 (800h-FFFh)
:
:
:
ORG 0x900
SUB1_P1:
;called subroutine
;page 1 (800h-FFFh)
:
:
A simple program to clear RAM location 20h-2Fh using
indirect addressing is shown in Example 4-2.
RETURN
;return to Call subroutine
;in page 0 (000h-7FFh)
EXAMPLE 4-2: INDIRECT ADDRESSING
movlw 0x20
movwf FSR
;initialize pointer
to RAM
;
NEXT
clrf
incf
INDF
FSR,F
;clear INDF register
;inc pointer
btfss FSR,4
;all done?
goto
NEXT
;NO, clear next
CONTINUE
:
;YES, continue
FIGURE 4-25: DIRECT/INDIRECT ADDRESSING
Direct Addressing
Indirect Addressing
RP1:RP0
6
0
IRP
7
FSR
0
from opcode
bank select
bank select
location select
location select
00
01
80h
10
100h
11
00h
180h
Data
Memory
7Fh
Bank 0
FFh
Bank 1
17Fh
Bank 2
1FFh
Bank 3
For memory map detail see Figure 4-5, Figure 4-6, Figure 4-7, and Figure 4-8.
1997 Microchip Technology Inc.
DS30234D-page 49
PIC16C6X
NOTES:
DS30234D-page 50
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 5-1: BLOCK DIAGRAM OF THE
RA3:RA0 PINS AND THE RA5
PIN
5.0
I/O PORTS
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Some pins for these I/O ports are multiplexed with an
alternate function(s) for the peripheral features on the
device. In general, when a peripheral is enabled, that
pin may not be used as a general purpose I/O pin.
Data
bus
D
Q
Q
VDD
P
WR
Port
5.1
PORTA and TRISA Register
CK
Applicable Devices
Data Latch
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
I/O pin(1)
N
D
Q
All devices have a 6-bit wide PORTA, except for the
PIC16C61 which has a 5-bit wide PORTA.
WR
TRIS
Pin RA4/T0CKI is a Schmitt Trigger input and an open
drain output. All other RA port pins have TTL input lev-
els and full CMOS output drivers. All pins have data
direction bits (TRIS registers) which can configure
these pins as output or input.
VSS
Q
CK
TTL
TRIS Latch
input
buffer
Setting a bit in the TRISA register puts the correspond-
ing output driver in a hi-impedance mode. Clearing a bit
in the TRISA register puts the contents of the output
latch on the selected pin.
RD TRIS
Q
D
Reading PORTA register reads the status of the pins
whereas writing to it will write to the port latch. All write
operations are read-modify-write operations. There-
fore, a write to a port implies that the port pins are read,
this value is modified, and then written to the port data
latch.
EN
RD PORT
Note 1: I/O pins have protection diodes to VDD and
VSS.
Pin RA4 is multiplexed with Timer0 module clock input
to become the RA4/T0CKI pin.
2: The PIC16C61 does not have an RA5 pin.
FIGURE 5-2: BLOCK DIAGRAM OF THE
RA4/T0CKI PIN
EXAMPLE 5-1: INITIALIZING PORTA
BCF
STATUS, RP0
;
Data
bus
BCF
STATUS, RP1 ; PIC16C66/67 only
D
Q
Q
CLRF
PORTA
; Initialize PORTA by
; clearing output
; data latches
WR
PORT
CK
I/O pin(1)
BSF
STATUS, RP0 ; Select Bank 1
N
MOVLW 0xCF
; Value used to
Data Latch
; initialize data
; direction
; Set RA<3:0> as inputs
; RA<5:4> as outputs
; TRISA<7:6> are always
; read as '0'.
D
Q
VSS
WR
TRIS
MOVWF TRISA
Schmitt
Trigger
input
Q
CK
TRIS Latch
buffer
RD TRIS
Q
D
EN
RD PORT
TMR0 clock input
Note 1: I/O pin has protection diodes to VSS only.
1997 Microchip Technology Inc.
DS30234D-page 51
PIC16C6X
TABLE 5-1:
Name
PORTA FUNCTIONS
Bit#
Buffer Type
Function
RA0
bit0
bit1
bit2
bit3
bit4
TTL
TTL
TTL
TTL
ST
Input/output
Input/output
Input/output
Input/output
RA1
RA2
RA3
RA4/T0CKI
Input/output or external clock input for Timer0.
Output is open drain type.
(1)
bit5
TTL
Input/output or slave select input for synchronous serial port.
RA5/SS
Legend: TTL = TTL input, ST = Schmitt Trigger input
Note 1: The PIC16C61 does not have PORTA<5> or TRISA<5>, read as ‘0’.
TABLE 5-2:
REGISTERS/BITS ASSOCIATED WITH PORTA
Value on:
POR,
BOR
Value on all
other resets
Address Name
Bit 7 Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(1)
05h
85h
PORTA
TRISA
—
—
—
—
RA5
RA4
RA3
RA2
RA1
RA0
--xx xxxx
--11 1111
--uu uuuu
--11 1111
(1)
PORTA Data Direction Register
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0'. Shaded cells are not used by PORTA.
Note 1: PORTA<5> and TRISA<5> are not implemented on the PIC16C61, read as '0'.
DS30234D-page 52
1997 Microchip Technology Inc.
PIC16C6X
This interrupt can wake the device from SLEEP. The
user, in the interrupt service routine, can clear the inter-
rupt in the following manner:
5.2
PORTB and TRISB Register
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
a) Any read or write of PORTB. This will end the
mismatch condition.
PORTB is an 8-bit wide bi-directional port. The corre-
sponding data direction register is TRISB. Setting a bit
in the TRISB register puts the corresponding output
driver in a hi-impedance mode. Clearing a bit in the
TRISB register puts the contents of the output latch on
the selected pin(s).
b) Clear flag bit RBIF.
A mismatch condition will continue to set flag bit RBIF.
Reading PORTB will end the mismatch condition, and
allow flag bit RBIF to be cleared.
This interrupt on mismatch feature, together with soft-
ware configurable pull-ups on these four pins allow
easy interface to a keypad and make it possible for
wake-up on key-depression. Refer to the Embedded
Control Handbook, Application Note, “Implementing
Wake-up on Key Stroke” (AN552).
EXAMPLE 5-2: INITIALIZING PORTB
BCF
CLRF
STATUS, RP0
PORTB
;
; Initialize PORTB by
; clearing output
; data latches
BSF
STATUS, RP0 ; Select Bank 1
MOVLW 0xCF
; Value used to
; initialize data
; direction
; Set RB<3:0> as inputs
; RB<5:4> as outputs
; RB<7:6> as inputs
Note: For PIC16C61/62/64/65, if a change on the
I/O pin should occur when a read operation
is being executed (start of the Q2 cycle),
then interrupt flag bit RBIF may not get set.
MOVWF TRISB
The interrupt on change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt on change
feature. Polling of PORTB is not recommended while
using the interrupt on change feature.
Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is
performed by clearing bit RBPU (OPTION<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are also
disabled on a Power-on Reset.
FIGURE 5-3: BLOCK DIAGRAM OF THE
RB7:RB4 PINS FOR
PIC16C61/62/64/65
VDD
Four of PORTB’s pins, RB7:RB4, have an interrupt on
change feature. Only pins configured as inputs can
cause this interrupt to occur (i.e., any RB7:RB4 pin
configured as an output is excluded from the interrupt
on change comparison). The input pins (of RB7:RB4)
are compared with the old value latched on the last
read of PORTB. The “mismatch” outputs of RB7:RB4
are OR’ed together to generate the RB port change
interrupt with flag bit RBIF (INTCON<0>).
RBPU(2)
weak
P
pull-up
Data Latch
Data bus
D
Q
I/O
pin(1)
WR Port
CK
TRIS Latch
D
Q
WR TRIS
TTL
Input
Buffer
CK
ST
Buffer
RD TRIS
RD Port
Latch
Q
D
EN
Set RBIF
From other
RB7:RB4 pins
Q
D
EN
RD Port
RB7:RB6 in serial programming mode
Note 1: I/O pins have diode protection to VDD and VSS.
2: To enable weak pull-ups, set the appropriate TRIS bit(s)
and clear the RPBU bit (OPTION<7>).
1997 Microchip Technology Inc.
DS30234D-page 53
PIC16C6X
FIGURE 5-4: BLOCK DIAGRAM OF THE
FIGURE 5-5: BLOCK DIAGRAM OF THE
RB7:RB4 PINS FOR
PIC16C62A/63/R63/64A/65A/
R65/66/67
RB3:RB0 PINS
VDD
RBPU(2)
weak
P
pull-up
VDD
Data Latch
RBPU(2)
Data bus
WR Port
weak
pull-up
D
Q
P
I/O
pin(1)
Data Latch
Data bus
CK
TRIS Latch
D
Q
I/O
WR Port
pin(1)
D
Q
CK
TRIS Latch
TTL
Input
Buffer
WR TRIS
CK
D
Q
WR TRIS
TTL
Input
Buffer
CK
ST
Buffer
RD TRIS
RD Port
Q
D
RD TRIS
RD Port
Latch
EN
Q
Q
D
EN
Q1
RB0/INT
Set RBIF
RD Port
Schmitt Trigger
Buffer
D
From other
RB7:RB4 pins
RD Port
Q3
Note 1: I/O pins have diode protection to VDD and VSS.
EN
2: To enable weak pull-ups, set the appropriate TRIS bit(s)
and clear the RPBU bit (OPTION<7>).
RB7:RB6 in serial programming mode
Note 1: I/O pins have diode protection to VDD and VSS.
2: To enable weak pull-ups, set the appropriate TRIS bit(s)
and clear the RPBU bit (OPTION<7>).
TABLE 5-3:
PORTB FUNCTIONS
Name
Bit#
Buffer Type Function
(1)
RB0/INT
bit0
Input/output pin or external interrupt input. Internal software programmable
weak pull-up.
TTL/ST
RB1
RB2
RB3
RB4
bit1
bit2
bit3
bit4
TTL
TTL
TTL
TTL
Input/output pin. Internal software programmable weak pull-up.
Input/output pin. Internal software programmable weak pull-up.
Input/output pin. Internal software programmable weak pull-up.
Input/output pin (with interrupt on change). Internal software programmable
weak pull-up.
RB5
RB6
RB7
bit5
bit6
bit7
TTL
Input/output pin (with interrupt on change). Internal software programmable
weak pull-up.
(2)
(2)
Input/output pin (with interrupt on change). Internal software programmable
weak pull-up. Serial programming clock.
TTL/ST
Input/output pin (with interrupt on change). Internal software programmable
weak pull-up. Serial programming data.
TTL/ST
Legend: TTL = TTL input, ST = Schmitt Trigger input
Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt.
2: This buffer is a Schmitt Trigger input when used in serial programming mode.
TABLE 5-4:
SUMMARY OF REGISTERS ASSOCIATED WITH PORTB
Value on:
POR,
BOR
Value on all
other resets
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
06h, 106h PORTB
86h, 186h TRISB
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx xxxx uuuu uuuuu
1111 1111 1111 1111
1111 1111 1111 1111
PORTB Data Direction Register
81h, 181h OPTION RBPU INTEDG T0CS
T0SE
PSA
PS2
PS1
PS0
Legend: x= unknown, u= unchanged. Shaded cells are not used by PORTB.
DS30234D-page 54
1997 Microchip Technology Inc.
PIC16C6X
5.3
PORTC and TRISC Register
FIGURE 5-6: PORTC BLOCK DIAGRAM
PORT/PERIPHERAL Select(2)
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Peripheral Data Out
VDD
0
PORTC is an 8-bit wide bi-directional port. Each pin is
individually configurable as an input or output through
the TRISC register. PORTC is multiplexed with several
peripheral functions (Table 5-5). PORTC pins have
Schmitt Trigger input buffers.
Data bus
D
Q
Q
P
WR
PORT
1
CK
Data Latch
I/O
D
Q
Q
pin(1)
WR
TRIS
When enabling peripheral functions, care should be
taken in defining TRIS bits for each PORTC pin. Some
peripherals override the TRIS bit to make a pin an out-
put, while other peripherals override the TRIS bit to
make a pin an input. Since the TRIS bit override is in
effect while the peripheral is enabled, read-modify-
write instructions (BSF, BCF, XORWF) with TRISC as
destination should be avoided. The user should refer to
the corresponding peripheral section for the correct
TRIS bit settings.
CK
N
TRIS Latch
VSS
Schmitt
Trigger
RD TRIS
Peripheral
OE(3)
Q
D
EN
RD
PORT
Peripheral input
EXAMPLE 5-3: INITIALIZING PORTC
BCF
BCF
CLRF
STATUS, RP0
STATUS, RP1 ; PIC16C66/67 only
PORTC
;
Note 1: I/O pins have diode protection to VDD and VSS.
2: Port/Peripheral select signal selects between port
data and peripheral output.
; Initialize PORTC by
; clearing output
; data latches
3: Peripheral OE (output enable) is only activated if
peripheral select is active.
BSF
STATUS, RP0 ; Select Bank 1
MOVLW 0xCF
; Value used to
; initialize data
; direction
MOVWF TRISC
; Set RC<3:0> as inputs
; RC<5:4> as outputs
; RC<7:6> as inputs
TABLE 5-5:
Name
PORTC FUNCTIONS FOR PIC16C62/64
Bit# Buffer Type Function
RC0/T1OSI/T1CKI
RC1/T1OSO
bit0
bit1
bit2
bit3
bit4
bit5
bit6
bit7
ST
ST
ST
ST
ST
ST
ST
ST
Input/output port pin or Timer1 oscillator input or Timer1 clock input
Input/output port pin or Timer1 oscillator output
RC2/CCP1
Input/output port pin or Capture1 input/Compare1 output/PWM1 output
2
RC3 can also be the synchronous serial clock for both SPI and I C modes.
RC3/SCK/SCL
2
RC4/SDI/SDA
RC5/SDO
RC4 can also be the SPI Data In (SPI mode) or data I/O (I C mode).
Input/output port pin or synchronous serial port data output
RC6
RC7
Input/output port pin
Input/output port pin
Legend: ST = Schmitt Trigger input
1997 Microchip Technology Inc.
DS30234D-page 55
PIC16C6X
TABLE 5-6:
Name
PORTC FUNCTIONS FOR PIC16C62A/R62/64A/R64
Bit# Buffer Type Function
RC0/T1OSO/T1CKI bit0
ST
ST
ST
ST
ST
ST
ST
ST
Input/output port pin or Timer1 oscillator output or Timer1 clock input
Input/output port pin or Timer1 oscillator input
RC1/T1OSI
RC2/CCP1
bit1
bit2
bit3
bit4
bit5
bit6
bit7
Input/output port pin or Capture input/Compare output/PWM1 output
2
RC3 can also be the synchronous serial clock for both SPI and I C modes.
RC3/SCK/SCL
2
RC4/SDI/SDA
RC5/SDO
RC4 can also be the SPI Data In (SPI mode) or data I/O (I C mode).
Input/output port pin or synchronous serial port data output
RC6
RC7
Input/output port pin
Input/output port pin
Legend: ST = Schmitt Trigger input
TABLE 5-7:
PORTC FUNCTIONS FOR PIC16C63/R63/65/65A/R65/66/67
Name
Bit# Buffer Type Function
RC0/T1OSO/T1CKI bit0
ST
ST
Input/output port pin or Timer1 oscillator output or Timer1 clock input
RC1/T1OSI/CCP2
bit1
Input/output port pin or Timer1 oscillator input or Capture2 input/Compare2
output/PWM2 output
RC2/CCP1
bit2
bit3
bit4
bit5
bit6
ST
ST
ST
ST
ST
Input/output port pin or Capture1 input/Compare1 output/PWM1 output
2
RC3 can also be the synchronous serial clock for both SPI and I C modes.
RC3/SCK/SCL
2
RC4/SDI/SDA
RC5/SDO
RC4 can also be the SPI Data In (SPI mode) or data I/O (I C mode).
Input/output port pin or synchronous serial port data output
RC6/TX/CK
Input/output port pin or USART Asynchronous Transmit, or USART Syn-
chronous Clock
RC7/RX/DT
bit7
ST
Input/output port pin or USART Asynchronous Receive, or USART Syn-
chronous Data
Legend: ST = Schmitt Trigger input
TABLE 5-8:
SUMMARY OF REGISTERS ASSOCIATED WITH PORTC
Value on:
POR,
BOR
Value on all
other resets
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
07h
87h
PORTC
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
xxxx xxxx uuuu uuuu
1111 1111 1111 1111
TRISC PORTC Data Direction Register
Legend: x= unknown, u= unchanged.
DS30234D-page 56
1997 Microchip Technology Inc.
PIC16C6X
5.4
PORTD and TRISD Register
FIGURE 5-7: PORTD BLOCK DIAGRAM
(IN I/O PORT MODE)
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Data
bus
PORTD is an 8-bit port with Schmitt Trigger input buff-
ers. Each pin is individually configurable as input or out-
put.
D
Q
WR
PORT
I/O pin(1)
CK
PORTD can be configured as an 8-bit wide micropro-
cessor port (parallel slave port) by setting control bit
PSPMODE (TRISE<4>). In this mode, the input buffers
are TTL.
Data Latch
D
Q
WR
TRIS
Schmitt
Trigger
input
CK
TRIS Latch
buffer
RD TRIS
Q
D
EN
RD PORT
Note 1: I/O pins have protection diodes to VDD and VSS.
TABLE 5-9:
Name
PORTD FUNCTIONS
Bit#
Buffer Type
Function
(1)
RD0/PSP0
RD1/PSP1
RD2/PSP2
RD3/PSP3
RD4/PSP4
RD5/PSP5
RD6/PSP6
RD7/PSP7
bit0
bit1
bit2
bit3
bit4
bit5
bit6
bit7
ST/TTL
Input/output port pin or parallel slave port bit0
Input/output port pin or parallel slave port bit1
Input/output port pin or parallel slave port bit2
Input/output port pin or parallel slave port bit3
Input/output port pin or parallel slave port bit4
Input/output port pin or parallel slave port bit5
Input/output port pin or parallel slave port bit6
Input/output port pin or parallel slave port bit7
(1)
ST/TTL
(1)
ST/TTL
(1)
ST/TTL
(1)
ST/TTL
(1)
ST/TTL
(1)
ST/TTL
(1)
ST/TTL
Legend: ST = Schmitt Trigger input, TTL = TTL input
Note 1: Buffer is a Schmitt Trigger when in I/O mode, and a TTL buffer when in Parallel Slave Port mode.
TABLE 5-10: SUMMARY OF REGISTERS ASSOCIATED WITH PORTD
Value on:
POR,
BOR
Value on all
other resets
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
08h
88h
89h
PORTD
RD7
RD6
RD5
RD4
RD3
RD2
RD1
RD0
xxxx xxxx uuuu uuuu
1111 1111 1111 1111
0000 -111 0000 -111
TRISD PORTD Data Direction Register
TRISE IBF OBF IBOV PSPMODE
PORTE Data Direction Bits
—
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0'. Shaded cells are not used by PORTD.
1997 Microchip Technology Inc.
DS30234D-page 57
PIC16C6X
5.5
PORTE and TRISE Register
FIGURE 5-8: PORTE BLOCK DIAGRAM
(IN I/O PORT MODE)
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Data
bus
D
Q
PORTE has three pins, RE2/CS, RE1/WR, and
RE0/RD which are individually configurable as inputs
or outputs. These pins have Schmitt Trigger input buff-
ers.
WR
PORT
I/O pin(1)
CK
Data Latch
I/O PORTE becomes control inputs for the micropro-
cessor port when bit PSPMODE (TRISE<4>) is set. In
this mode, the user must make sure that the
TRISE<2:0> bits are set (pins are configured as digital
inputs). In this mode the input buffers are TTL.
D
Q
WR
TRIS
Schmitt
Trigger
input
CK
TRIS Latch
buffer
Figure 5-9 shows the TRISE register, which controls
the parallel slave port operation and also controls the
direction of the PORTE pins.
RD TRIS
Q
D
EN
RD PORT
Note 1: I/O pins have protection diodes to VDD and VSS.
FIGURE 5-9: TRISE REGISTER (ADDRESS 89h)
R-0
IBF
R-0
R/W-0
R/W-0
U-0
—
R/W-1
bit2
R/W-1
bit1
R/W-1
bit0
OBF
IBOV PSPMODE
R
= Readable bit
W = Writable bit
bit7
bit0
U
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7 :
bit 6:
bit 5:
bit 4:
IBF: Input Buffer Full Status bit
1 = A word has been received and is waiting to be read by the CPU
0 = No word has been received
OBF: Output Buffer Full Status bit
1 = The output buffer still holds a previously written word
0 = The output buffer has been read
IBOV: Input Buffer Overflow Detect bit (in microprocessor mode)
1 = A write occurred when a previously input word has not been read (must be cleared in software)
0 = No overflow occurred
PSPMODE: Parallel Slave Port Mode Select bit
1 = Parallel slave port mode
0 = General purpose I/O mode
bit 3:
bit 2:
Unimplemented: Read as '0'
PORTE Data Direction Bits
Bit2: Direction Control bit for pin RE2/CS
1 = Input
0 = Output
bit 1:
bit 0:
Bit1: Direction Control bit for pin RE1/WR
1 = Input
0 = Output
Bit0: Direction Control bit for pin RE0/RD
1 = Input
0 = Output
DS30234D-page 58
1997 Microchip Technology Inc.
PIC16C6X
TABLE 5-11: PORTE FUNCTIONS
Name
Bit#
Buffer Type Function
(1)
RE0/RD
bit0
ST/TTL
ST/TTL
ST/TTL
Input/output port pin or Read control input in parallel slave port mode.
RD
1 = Not a read operation
0 = Read operation. The system reads the PORTD register (if
chip selected)
(1)
(1)
RE1/WR
RE2/CS
bit1
bit2
Input/output port pin or Write control input in parallel slave port mode.
WR
1 = Not a write operation
0 = Write operation.The system writes to the PORTD register (if
chip selected)
Input/output port pin or Chip select control input in parallel slave port
mode.
CS
1 = Device is not selected
0 = Device is selected
Legend: ST = Schmitt Trigger input, TTL = TTL input
Note 1: Buffer is a Schmitt Trigger when in I/O mode, and a TTL buffer when in Parallel Slave Port (PSP) mode.
TABLE 5-12: SUMMARY OF REGISTERS ASSOCIATED WITH PORTE
Value on:
POR,
BOR
Value on all
other resets
Address Name
Bit 7 Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
09h
89h
PORTE
TRISE
—
—
—
—
—
—
RE2
RE1
RE0
---- -xxx
0000 -111
---- -uuu
0000 -111
PORTE Data Direction Bits
IBF OBF
IBOV
PSPMODE
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0'. Shaded cells not used by PORTE.
1997 Microchip Technology Inc.
DS30234D-page 59
PIC16C6X
5.6
I/O Programming Considerations
EXAMPLE 5-4: READ-MODIFY-WRITE
INSTRUCTIONS ON AN
I/O PORT
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
;Initial PORT settings: PORTB<7:4> Inputs
5.6.1
BI-DIRECTIONAL I/O PORTS
;
PORTB<3:0> Outputs
;PORTB<7:6> have external pull-ups and are
;not connected to other circuitry
;
Any instruction which writes, operates internally as a
read followed by a write operation. The BCF and BSF
instructions, for example, read the register into the
CPU, execute the bit operation and write the result back
to the register. Caution must be used when these
instructions are applied to a port with both inputs and
outputs defined. For example, a BSFoperation on bit5
of PORTB will cause all eight bits of PORTB to be read
into the CPU. Then the BSF operation takes place on
bit5 and PORTB is written to the output latches. If
another bit of PORTB is used as a bi-directional I/O pin
(e.g., bit0) and it is defined as an input at this time, the
input signal present on the pin itself would be read into
the CPU and rewritten to the data latch of this particular
pin, overwriting the previous content. As long as the pin
stays in the input mode, no problem occurs. However, if
bit0 is switched into output mode later on, the content
of the data latch may now be unknown.
;
;
PORT latch PORT pins
---------- ---------
BCF PORTB, 7
BCF PORTB, 6
BSF STATUS, RP0
BCF TRISB, 7
BCF TRISB, 6
; 01pp pppp
; 10pp pppp
;
; 10pp pppp
; 10pp pppp
11pp pppp
11pp pppp
11pp pppp
10pp pppp
;
;Note that the user may have expected the
;pin values to be 00pp pppp. The 2nd BCF
;caused RB7 to be latched as the pin value
;(high).
A pin actively outputting a Low or High should not be
driven from external devices at the same time in order
to change the level on this pin (“wired-or”, “wired-and”).
The resulting high output currents may damage the
chip.
Reading the port register, reads the values of the port
pins. Writing to the port register writes the value to the
port latch. When using read-modify-write instructions
(ex. BCF, BSF, etc.) on a port, the value of the port pins
is read, the desired operation is done to this value, and
this value is then written to the port latch.
5.6.2
SUCCESSIVE OPERATIONS ON I/O PORTS
The actual write to an I/O port happens at the end of an
instruction cycle, whereas for reading, the data must be
valid at the beginning of the instruction cycle
(Figure 5-10). Therefore, care must be exercised if a
write followed by a read operation is carried out on the
same I/O port. The sequence of instructions should be
such to allow the pin voltage to stabilize (load depen-
dent) before the next instruction which causes that file
to be read into the CPU is executed. Otherwise, the
previous state of that pin may be read into the CPU
rather than the new state. When in doubt, it is better to
separate these instructions with a NOP or another
instruction not accessing this I/O port.
Example 5-4 shows the effect of two sequential
read-modify-write instructions on an I/O port.
FIGURE 5-10: SUCCESSIVE I/O OPERATION
Q4
Q4
Q4
Q1 Q2
Q4
Q3
Q3
Q3
Q3
Q1 Q2
PC
Q1 Q2
Q1 Q2
Note:
This example shows a write to PORTB
followed by a read from PORTB.
PC + 3
NOP
PC
Instruction
fetched
PC + 1
PC + 2
NOP
MOVWF PORTB MOVF PORTB,W
write to
PORTB
Note that:
data setup time = (0.25TCY - TPD)
RB7:RB0
where TCY = instruction cycle
TPD = propagation delay
Port pin
sampled here
TPD
Therefore, at higher clock frequencies,
a write followed by a read may be prob-
lematic.
Instruction
executed
NOP
MOVWF PORTB
write to
MOVF PORTB,W
PORTB
DS30234D-page 60
1997 Microchip Technology Inc.
PIC16C6X
5.7
Parallel Slave Port
FIGURE 5-11: PORTD AND PORTE AS A
PARALLEL SLAVE PORT
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PORTD operates as an 8-bit wide parallel slave port
(microprocessor port) when control bit PSPMODE
(TRISE<4>) is set. In slave mode it is asynchronously
readable and writable by the external world through
RD control input (RE0/RD) and WR control input pin
(RE1/WR).
Data bus
D
Q
WR
PORT
RDx
pin
CK
TTL
Q
D
It can directly interface to an 8-bit microprocessor data
bus. The external microprocessor can read or write the
PORTD latch as an 8-bit latch. Setting PSPMODE
enables port pin RE0/RD to be the RD input, RE1/WR
to be the WR input and RE2/CS to be the CS (chip
select) input. For this functionality, the corresponding
data direction bits of the TRISE register (TRISE<2:0>)
must be configured as inputs (set).
RD
PORT
EN
One bit of PORTD
Set interrupt flag
PSPIF (PIR1<7>)
There are actually two 8-bit latches, one for data-out
(from the PIC16/17) and one for data input. The user
writes 8-bit data to PORTD data latch and reads data
from the port pin latch (note that they have the same
address). In this mode, the TRISD register is ignored
since the microprocessor is controlling the direction of
data flow.
Read
RD
CS
WR
TTL
Chip Select
TTL
TTL
Write
A write to the PSP occurs when both the CS and WR
lines are first detected low. When either the CS or WR
lines become high (level triggered), then the Input
Buffer Full status flag bit IBF (TRISE<7>) is set on the
Q4 clock cycle, following the next Q2 cycle, to signal
the write is complete (Figure 5-12).The interrupt flag bit
PSPIF (PIR1<7>) is also set on the same Q4 clock
cycle. IBF can only be cleared by reading the PORTD
input latch. The input Buffer Overflow status flag bit
IBOV (TRISE<5>) is set if a second write to the Parallel
Slave Port is attempted when the previous byte has not
been read out of the buffer.
Note: I/O pin has protection diodes to VDD and VSS.
A read from the PSP occurs when both the CS and RD
lines are first detected low. The Output Buffer Full sta-
tus flag bit OBF (TRISE<6>) is cleared immediately
(Figure 5-13) indicating that the PORTD latch is waiting
to be read by the external bus. When either the CS or
RD pin becomes high (level triggered), the interrupt flag
bit PSPIF is set on the Q4 clock cycle, following the
next Q2 cycle, indicating that the read is complete.
OBF remains low until data is written to PORTD by the
user firmware.
When not in Parallel Slave Port mode, the IBF and OBF
bits are held clear. However, if flag bit IBOV was previ-
ously set, it must be cleared in firmware.
An interrupt is generated and latched into flag bit
PSPIF when a read or write operation is completed.
PSPIF must be cleared by the user in firmware and the
interrupt can be disabled by clearing the interrupt
enable bit PSPIE (PIE1<7>).
1997 Microchip Technology Inc.
DS30234D-page 61
PIC16C6X
FIGURE 5-12: PARALLEL SLAVE PORT WRITE WAVEFORMS
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
CS
WR
RD
PORTD<7:0>
IBF
OBF
PSPIF
FIGURE 5-13: PARALLEL SLAVE PORT READ WAVEFORMS
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
CS
WR
RD
PORTD<7:0>
IBF
OBF
PSPIF
TABLE 5-13: REGISTERS ASSOCIATED WITH PARALLEL SLAVE PORT
Value on:
POR,
BOR
Value on all
other resets
Address Name
Bit 7 Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
08h
09h
89h
0Ch
8Ch
PORTD PSP7 PSP6 PSP5
PSP4
—
PSP3
—
PSP2
RE2
PSP1
RE1
PSP0
RE0
xxxx xxxx
---- -xxx
0000 -111
uuuu uuuu
---- -uuu
0000 -111
0000 0000
0000 0000
PORTE
TRISE
PIR1
—
—
—
PORTE Data Direction Bits
IBF
OBF
IBOV PSPMODE
—
(1)
(2)
(2)
PSPIF
PSPIE
RCIF
RCIE
TXIF
TXIE
SSPIF CCP1IF TMR2IF TRM1IF 0000 0000
SSPIE CCP1IE TMR2IE TMR1IE 0000 0000
(1)
(2)
(2)
PIE1
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0'. Shaded cells are not used by the PSP.
Note 1: These bits are reserved, always maintain these bits clear.
2: These bits are implemented on the PIC16C65/65A/R65/67 only.
DS30234D-page 62
1997 Microchip Technology Inc.
PIC16C6X
6.3
Timer2 Overview
6.0
OVERVIEW OF TIMER
MODULES
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Applicable Devices
Timer2 is an 8-bit timer with a programmable prescaler
and a programmable postscaler, as well as an 8-bit
Period Register (PR2). Timer2 can be used with the
CCP module (in PWM mode) as well as the Baud Rate
Generator for the Synchronous Serial Port (SSP). The
prescaler option allows Timer2 to increment at the fol-
lowing rates: 1:1, 1:4, and 1:16.
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
All PIC16C6X devices have three timer modules except
for the PIC16C61, which has one timer module. Each
module can generate an interrupt to indicate that an
event has occurred (i.e., timer overflow). Each of these
modules are detailed in the following sections. The
timer modules are:
The postscaler allows TMR2 register to match the
period register (PR2) a programmable number of times
before generating an interrupt. The postscaler can be
programmed from 1:1 to 1:16 (inclusive).
• Timer0 module (Section 7.0)
• Timer1 module (Section 8.0)
• Timer2 module (Section 9.0)
6.1
Timer0 Overview
6.4
CCP Overview
Applicable Devices
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The Timer0 module is a simple 8-bit overflow counter.
The clock source can be either the internal system
clock (Fosc/4) or an external clock. When the clock
source is an external clock, the Timer0 module can be
selected to increment on either the rising or falling
edge.
The CCP module(s) can operate in one of three modes:
16-bit capture, 16-bit compare, or up to 10-bit Pulse
Width Modulation (PWM).
Capture mode captures the 16-bit value of TMR1 into
the CCPRxH:CCPRxL register pair. The capture event
can be programmed for either the falling edge, rising
edge, fourth rising edge, or sixteenth rising edge of the
CCPx pin.
The Timer0 module also has a programmable pres-
caler option. This prescaler can be assigned to either
the Timer0 module or the Watchdog Timer. Bit PSA
(OPTION<3>) assigns the prescaler, and bits PS2:PS0
(OPTION<2:0>) determine the prescaler value. TMR0
can increment at the following rates: 1:1 when the pres-
caler is assigned to Watchdog Timer, 1:2, 1:4, 1:8,
1:16, 1:32, 1:64, 1:128, and 1:256.
Compare mode compares the TMR1H:TMR1L register
pair to the CCPRxH:CCPRxL register pair. When a
match occurs, an interrupt can be generated and the
output pin CCPx can be forced to a given state (High or
Low) and Timer1 can be reset.This depends on control
bits CCPxM3:CCPxM0.
Synchronization of the external clock occurs after the
prescaler. When the prescaler is used, the external
clock frequency may be higher then the device’s fre-
quency. The maximum frequency is 50 MHz, given the
high and low time requirements of the clock.
PWM mode compares the TMR2 register to a 10-bit
duty cycle register (CCPRxH:CCPRxL<5:4>) as well as
to an 8-bit period register (PR2). When the TMR2 reg-
ister = Duty Cycle register, the CCPx pin will be forced
low. When TMR2 = PR2, TMR2 is cleared to 00h, an
interrupt can be generated, and the CCPx pin (if an out-
put) will be forced high.
6.2
Timer1 Overview
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Timer1 is a 16-bit timer/counter. The clock source can
be either the internal system clock (Fosc/4), an external
clock, or an external crystal. Timer1 can operate as
either a timer or a counter. When operating as a
counter (external clock source), the counter can either
operate synchronized to the device or asynchronously
to the device. Asynchronous operation allows Timer1 to
operate during sleep, which is useful for applications
that require a real-time clock as well as the power sav-
ings of SLEEP mode.
TImer1 also has a prescaler option which allows TMR1
to increment at the following rates: 1:1, 1:2, 1:4, and
1:8.TMR1 can be used in conjunction with the Capture/
Compare/PWM module. When used with a CCP mod-
ule, Timer1 is the time-base for 16-bit capture or 16-bit
compare and must be synchronized to the device.
1997 Microchip Technology Inc.
DS30234D-page 63
PIC16C6X
NOTES:
DS30234D-page 64
1997 Microchip Technology Inc.
PIC16C6X
(OPTION<4>). Clearing bit T0SE selects the rising
edge. Restrictions on the external clock input are dis-
cussed in detail in Section 7.2.
7.0
TIMER0 MODULE
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The prescaler is mutually exclusively shared between
the Timer0 module and the Watchdog Timer. The pres-
caler assignment is controlled in software by control bit
PSA (OPTION<3>). Clearing bit PSA will assign the
prescaler to the Timer0 module. The prescaler is not
readable or writable. When the prescaler is assigned to
the Timer0 module, prescale values of 1:2, 1:4, ...,
1:256 are selectable. Section 7.3 details the operation
of the prescaler.
The Timer0 module has the following features:
• 8-bit timer/counter register, TMR0
- Read and write capability
- Interrupt on overflow from FFh to 00h
• 8-bit software programmable prescaler
• Internal or external clock select
- Edge select for external clock
Figure 7-1 is a simplified block diagram of the Timer0
module.
7.1
TMR0 Interrupt
Applicable Devices
Timer mode is selected by clearing bit T0CS
(OPTION<5>). In timer mode, the Timer0 module will
increment every instruction cycle (without prescaler). If
TMR0 register is written, the increment is inhibited for
the following two instruction cycles (Figure 7-2 and
Figure 7-3). The user can work around this by writing
an adjusted value to the TMR0 register.
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The TMR0 interrupt is generated when the register
(TMR0) overflows from FFh to 00h. This overflow sets
interrupt flag bit T0IF (INTCON<2>). The interrupt can
be masked by clearing enable bit T0IE (INTCON<5>).
Flag bit T0IF must be cleared in software by the TImer0
interrupt service routine before re-enabling this inter-
rupt. The TMR0 interrupt cannot wake the processor
from SLEEP since the timer is shut off during SLEEP.
Figure 7-4 displays the Timer0 interrupt timing.
Counter mode is selected by setting bit T0CS. In this
mode, Timer0 will increment either on every rising or
falling edge of pin RA4/T0CKI. The incrementing edge
is determined by the source edge select bit T0SE
FIGURE 7-1: TIMER0 BLOCK DIAGRAM
Data bus
RA4/T0CKI
pin
FOSC/4
0
1
PSout
8
TMR0 reg
1
0
Sync with
Internal
clocks
Programmable
Prescaler
PSout
(2 cycle delay)
T0SE
3
Set bit T0IF
on overflow
PS2, PS1, PS0
PSA
T0CS
Note 1: Bits, T0CS, T0SE, PSA, and PS2, PS1, PS0 are (OPTION<5:0).
2: The prescaler is shared with Watchdog Timer (refer to Figure 7-6 for detailed diagram).
FIGURE 7-2: TIMER0 TIMING: INTERNAL CLOCK/NO PRESCALER
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
PC
(Program
Counter)
PC-1
PC
PC+1
PC+2
PC+3
PC+4
PC+5
PC+6
Instruction
Fetch
MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W
MOVWF TMR0
T0
T0+1
T0+2
NT0
NT0
NT0
NT0+1
NT0+2
TMR0
Instruction
Executed
Read TMR0
reads NT0 + 1
Read TMR0
reads NT0
Read TMR0
reads NT0
Read TMR0
reads NT0
Read TMR0
reads NT0 + 2
Write TMR0
executed
1997 Microchip Technology Inc.
DS30234D-page 65
PIC16C6X
FIGURE 7-3: TIMER0 TIMING: INTERNAL CLOCK/PRESCALE 1:2
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
PC
(Program
Counter)
PC-1
PC
PC+1
PC+2
PC+3
PC+4
PC+5
PC+6
MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W
MOVWF TMR0
Instruction
Fetch
T0
T0+1
NT0+1
NT0
TMR0
Instruction
Execute
Read TMR0
reads NT0
Read TMR0
reads NT0
Read TMR0
reads NT0
Read TMR0
reads NT0
Read TMR0
reads NT0 + 1
Write TMR0
executed
FIGURE 7-4: TMR0 INTERRUPT TIMING
Q1 Q2 Q3
Q4
Q1 Q2 Q3
Q4
Q1 Q2 Q3
Q4
Q1 Q2 Q3
Q4
Q1 Q2 Q3
Q4
OSC1
CLKOUT(3)
Timer0
FEh
FFh
00h
01h
02h
1
1
T0IF bit
(INTCON<2>)
GIE bit
(INTCON<7>)
INSTRUCTION
FLOW
PC
PC
PC +1
PC +1
0004h
0005h
Instruction
fetched
Inst (PC)
Inst (PC+1)
Inst (0004h)
Inst (0005h)
Instruction
executed
Inst (PC-1)
Dummy cycle
Dummy cycle
Inst (0004h)
Inst (PC)
Note 1: Interrupt flag bit T0IF is sampled here (every Q1).
2: Interrupt latency = 4Tcy where Tcy = instruction cycle time.
3: CLKOUT is available only in RC oscillator mode.
DS30234D-page 66
1997 Microchip Technology Inc.
PIC16C6X
When a prescaler is used, the external clock input is
divided by the asynchronous ripple-counter type pres-
caler so that the prescaler output is symmetrical. For
the external clock to meet the sampling requirement,
the ripple-counter must be taken into account. There-
fore, it is necessary for T0CKI to have a period of at
least 4Tosc (and a small RC delay of 40 ns) divided by
the prescaler value. The only requirement on T0CKI
high and low time is that they do not violate the mini-
mum pulse width requirement of 10 ns. Refer to param-
eters 40, 41 and 42 in the electrical specification of the
desired device.
7.2
Using Timer0 with External Clock
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
When an external clock input is used for Timer0, it must
meet certain requirements. The requirements ensure
the external clock can be synchronized with the internal
phase clock (TOSC). Also, there is a delay in the actual
incrementing of Timer0 after synchronization.
7.2.1
EXTERNAL CLOCK SYNCHRONIZATION
When no prescaler is used, the external clock input is
the same as the prescaler output. The synchronization
of T0CKI with the internal phase clocks is accom-
plished by sampling the prescaler output on the Q2 and
Q4 cycles of the internal phase clocks (Figure 7-5).
Therefore, it is necessary for T0CKI to be high for at
least 2Tosc (and a small RC delay of 20 ns) and low for
at least 2Tosc (and a small RC delay of 20 ns). Refer to
the electrical specification of the desired device.
7.2.2
TIMER0 INCREMENT DELAY
Since the prescaler output is synchronized with the
internal clocks, there is a small delay from the time the
external clock edge occurs to the time the Timer0 mod-
ule is actually incremented. Figure 7-5 shows the delay
from the external clock edge to the timer incrementing.
FIGURE 7-5: TIMER0 TIMING WITH EXTERNAL CLOCK
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Small pulse
misses sampling
External Clock Input or
(2)
Prescaler output
(1)
(3)
External Clock/Prescaler
Output after sampling
Increment Timer0 (Q4)
Timer0
T0
T0 + 1
T0 + 2
Note 1: Delay from clock input change to Timer0 increment is 3Tosc to 7Tosc. (Duration of Q = Tosc).
Therefore, the error in measuring the interval between two edges on Timer0 input = ±4Tosc max.
2: External clock if no prescaler selected, prescaler output otherwise.
3: The arrows indicate the points in time where sampling occurs.
1997 Microchip Technology Inc.
DS30234D-page 67
PIC16C6X
The PSA and PS2:PS0 bits (OPTION<3:0>) determine
the prescaler assignment and prescale ratio.
7.3
Prescaler
Applicable Devices
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g. CLRF TMR0,
MOVWF TMR0, BSF TMR0,bitx) will clear the pres-
caler count. When assigned to the Watchdog Timer, a
CLRWDTinstruction will clear the Watchdog Timer and
the prescaler count. The prescaler is not readable or
writable.
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
An 8-bit counter is available as a prescaler for the
Timer0 module or as a postscaler for the Watchdog
Timer (WDT), respectively (Figure 7-6). For simplicity,
this counter is being referred to as “prescaler” through-
out this data sheet. Note that the prescaler may be
used by either the Timer0 module or the Watchdog
Timer, but not both. Thus, a prescaler assignment for
the Timer0 module means that there is no prescaler for
the Watchdog Timer, and vice-versa.
Note: Writing to TMR0 when the prescaler is
assigned to Timer0 will clear the prescaler
count, but will not change the prescaler
assignment.
FIGURE 7-6: BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER
Data Bus
8
CLKOUT (=Fosc/4)
M
U
X
1
0
0
1
M
U
X
RA4/T0CKI
pin
SYNC
2
Cycles
TMR0 reg
T0SE
T0CS
Set flag bit T0IF
on Overflow
PSA
0
1
8-bit Prescaler
M
U
X
Watchdog
Timer
8
8 - to - 1MUX
PS2:PS0
PSA
1
0
WDT Enable bit
M U X
PSA
WDT
Time-out
Note: T0CS, T0SE, PSA, PS2:PS0 are (OPTION<5:0>).
DS30234D-page 68
1997 Microchip Technology Inc.
PIC16C6X
7.3.1
SWITCHING PRESCALER ASSIGNMENT
The prescaler assignment is fully under software con-
trol, i.e., it can be changed “on the fly” during program
execution.
Note: To avoid an unintended device RESET, the
following instruction sequence (shown in
Example 7-1) must be executed when
changing the prescaler assignment from
Timer0 to the WDT. This precaution must
be followed even if the WDT is disabled.
EXAMPLE 7-1: CHANGING PRESCALER (TIMER0→WDT)
1) BSF
STATUS, RP0
;Bank 1
2) MOVLW b'xx0x0xxx'
3) MOVWF OPTION_REG
;Select clock source and prescale value of
Lines 2 and 3 do NOT have to
be included if the final desired
prescale value is other than 1:1.
If 1:1 is final desired value, then
a temporary prescale value is
set in lines 2 and 3 and the final
prescale value will be set in lines
10 and 11.
;other than 1:1
4) BCF
5) CLRF
6) BSF
STATUS, RP0
TMR0
;Bank 0
;Clear TMR0 and prescaler
STATUS, RP1
;Bank 1
7) MOVLW b'xxxx1xxx'
8) MOVWF OPTION_REG
9) CLRWDT
;Select WDT, do not change prescale value
;
;Clears WDT and prescaler
10) MOVLW b'xxxx1xxx'
11) MOVWF OPTION_REG
;Select new prescale value and WDT
;
12) BCF
STATUS, RP0
;Bank 0
To change prescaler from the WDT to the Timer0 mod-
ule, use the sequence shown in Example 7-2.
EXAMPLE 7-2: CHANGING PRESCALER (WDT→TIMER0)
CLRWDT
BSF
MOVLW
MOVWF
BCF
;Clear WDT and prescaler
STATUS, RP0 ;Bank 1
b'xxxx0xxx' ;Select TMR0, new prescale value and clock source
OPTION_REG
;
STATUS, RP0 ;Bank 0
TABLE 7-1:
REGISTERS ASSOCIATED WITH TIMER0
Value on:
POR,
BOR
Value on all
other resets
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
01h, 101h TMR0
Timer0 module’s register
xxxx xxxx uuuu uuuu
RBIF 0000 000x 0000 000u
(1)
0Bh,8Bh,
INTCON GIE
PEIE
T0IE
INTE
T0SE
RBIE
PSA
T0IF
PS2
INTF
PS1
10Bh,18Bh
81h, 181h OPTION RBPU INTEDG
85h TRISA
T0CS
PS0
1111 1111 1111 1111
--11 1111 --11 1111
(1)
PORTA Data Direction Register
—
—
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0'. Shaded cells are not used by Timer0.
Note 1: TRISA<5> and bit PEIE are not implemented on the PIC16C61, read as '0'.
1997 Microchip Technology Inc.
DS30234D-page 69
PIC16C6X
NOTES:
DS30234D-page 70
1997 Microchip Technology Inc.
PIC16C6X
Timer1 also has an internal “reset input”.This reset can
be generated by CCP1 or CCP2 (Capture/Compare/
PWM) module. See Section 10.0 for details. Figure 8-1
shows the Timer1 control register.
8.0
TIMER1 MODULE
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Timer1 is a 16-bit timer/counter consisting of two 8-bit
registers (TMR1H and TMR1L) which are readable and
writable. Register TMR1 (TMR1H:TMR1L) increments
from 0000h to FFFFh and rolls over to 0000h. The
TMR1 Interrupt, if enabled, is generated on overflow
which is latched in interrupt flag bit TMR1IF (PIR1<0>).
This interrupt can be enabled/disabled by setting/clear-
ing the TMR1 interrupt enable bit TMR1IE (PIE1<0>).
For the PIC16C62A/R62/63/R63/64A/R64/65A/R65/
R66/67, when the Timer1 oscillator is enabled
(T1OSCEN is set), the RC1 and RC0 pins become
inputs. That is, the TRISC<1:0> value is ignored.
For the PIC16C62/64/65, when the Timer1 oscillator is
enabled (T1OSCEN is set), RC1 pin becomes an input,
however the RC0 pin will have to be configured as an
input by setting the TRISC<0> bit.
Timer1 can operate in one of two modes:
The Timer1 module also has a software programmable
prescaler.
• As a timer
• As a counter
The operating mode is determined by clock select bit,
TMR1CS (T1CON<1>) (Figure 8-2).
In timer mode, Timer1 increments every instruction
cycle. In counter mode, it increments on every rising
edge of the external clock input.
Timer1 can be enabled/disabled by setting/clearing
control bit TMR1ON (T1CON<0>).
FIGURE 8-1: T1CON:TIMER1 CONTROL REGISTER (ADDRESS 10h)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON
bit0
R
= Readable bit
W = Writable bit
U
bit7
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7-6: Unimplemented: Read as '0'
bit 5-4: T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits
11= 1:8 Prescale value
10= 1:4 Prescale value
01= 1:2 Prescale value
00= 1:1 Prescale value
bit 3:
bit 2:
T1OSCEN: Timer1 Oscillator Enable Control bit
1 = Oscillator is enabled
0 = Oscillator is shut off
Note: The oscillator inverter and feedback resistor are turned off to eliminate power drain.
T1SYNC: Timer1 External Clock Input Synchronization Control bit
TMR1CS = 1
1 = Do not synchronize external clock input
0 = Synchronize external clock input
TMR1CS = 0
This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.
bit 1:
bit 0:
TMR1CS: Timer1 Clock Source Select bit
1 = External clock from T1OSI (on the rising edge) (See pinouts for pin with T1OSI function)
0 = Internal clock (Fosc/4)
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
1997 Microchip Technology Inc.
DS30234D-page 71
PIC16C6X
8.2.1
EXTERNAL CLOCK INPUT TIMING FOR
SYNCHRONIZED COUNTER MODE
8.1
Timer1 Operation in Timer Mode
Applicable Devices
When an external clock input is used for Timer1 in syn-
chronized counter mode, it must meet certain require-
ments. The external clock requirement is due to
internal phase clock (Tosc) synchronization. Also, there
is a delay in the actual incrementing of TMR1 after syn-
chronization.
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Timer mode is selected by clearing bit TMR1CS
(T1CON<1>). In this mode, the input clock to the timer
is Fosc/4. The synchronize control bit T1SYNC
(T1CON<2>) has no effect since the internal clock is
always in sync.
When the prescaler is 1:1, the external clock input is
the same as the prescaler output. The synchronization
of T1CKI with the internal phase clocks is accom-
plished by sampling the prescaler output on the Q2 and
Q4 cycles of the internal phase clocks. Therefore, it is
necessary for T1CKI to be high for at least 2Tosc (and
a small RC delay of 20 ns) and low for at least 2Tosc
(and a small RC delay of 20 ns). Refer to appropriate
electrical specification section, parameters 45, 46, and
47.
8.2
Timer1 Operation in Synchronized
Counter Mode
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Counter mode is selected by setting bit TMR1CS. In
this mode the timer increments on every rising edge of
clock input on T1OSI when enable bit T1OSCEN is set
or pin with T1CKI when bit T1OSCEN is cleared.
Note: The T1OSI function is multiplexed to differ-
ent pins, depending on the device. See the
pinout descriptions to see which pin has
the T1OSI function.
When a prescaler other than 1:1 is used, the external
clock input is divided by the asynchronous ripple-
counter type prescaler so that the prescaler output is
symmetrical. In order for the external clock to meet the
sampling requirement, the ripple counter must be taken
into account. Therefore, it is necessary for T1CKI to
have a period of at least 4Tosc (and a small RC delay
of 40 ns) divided by the prescaler value. The only
requirement on T1CKI high and low time is that they do
not violate the minimum pulse width requirements of
10 ns). Refer to applicable electrical specification sec-
tion, parameters 40, 42, 45, 46, and 47.
If T1SYNC is cleared, then the external clock input is
synchronized with internal phase clocks. The synchro-
nization is done after the prescaler stage. The pres-
caler stage is an asynchronous ripple counter.
In this configuration, during SLEEP mode, Timer1 will
not increment even if an external clock is present, since
the synchronization circuit is shut off. The prescaler,
however, will continue to increment.
FIGURE 8-2: TIMER1 BLOCK DIAGRAM
TMR1IF
Overflow
Interrupt
flag bit
Synchronized
0
TMR1
clock input
TMR1L
TMR1H
1
TMR1ON
on/off
T1SYNC
T1OSC
(3)
(2)
T1OSO
1
Synchronize
det
Prescaler
1, 2, 4, 8
T1OSCEN
Enable
Oscillator
Fosc/4
Internal
Clock
0
(2)
(1)
T1OSI
2
SLEEP input
TMR1CS
T1CKPS1:T1CKPS0
Note 1: When enable bit T1OSCEN is cleared, the inverter and feedback resistor are turned off. This eliminates power drain.
2: See pinouts for pins with T1OSO and T1OSI functions.
3: For the PIC16C62/64/65, the Schmitt Trigger is not implemented in external clock mode.
DS30234D-page 72
1997 Microchip Technology Inc.
PIC16C6X
8.3
Timer1 Operation in Asynchronous
Counter Mode
EXAMPLE 8-1: READING A 16-BIT
FREE-RUNNING TIMER
Applicable Devices
;
All Interrupts are disabled
MOVF
MOVWF TMPH
MOVF
MOVWF TMPL
MOVF
SUBWF TMPH,
TMR1H,
W
;Read high byte
;
;Read low byte
;
;Read high byte
;Sub 1st read
;with 2nd read
;is result = 0
;Good 16-bit read
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
If control bit T1SYNC (T1CON<2>) is set, the external
clock input is not synchronized. The timer continues to
increment asynchronous to the internal phase clocks.
The timer will continue to run during SLEEP and gener-
ate an interrupt on overflow which will wake the proces-
sor. However, special precautions in software are
needed to read-from or write-to the Timer1 register
pair, TMR1L and TMR1H (Section 8.3.2).
TMR1L,
W
TMR1H,
W
W
BTFSC STATUS,Z
GOTO CONTINUE
; TMR1L may have rolled over between the read
; of the high and low bytes. Reading the high
; and low bytes now will read a good value.
In asynchronous counter mode, Timer1 cannot be used
as a time-base for capture or compare operations.
MOVF
TMR1H,
W
;Read high byte
MOVWF TMPH
;
8.3.1
EXTERNAL CLOCK INPUT TIMING WITH
UNSYNCHRONIZED CLOCK
MOVF
TMR1L,
W
;Read low byte
;
MOVWF TMPL
;
Re-enable Interrupt (if required)
If control bit T1SYNC is set, the timer will increment
completely asynchronously. The input clock must meet
certain minimum high time and low time requirements,
as specified in timing parameters (45 - 47).
CONTINUE
:
;Continue with
;your code
8.4
Timer1 Oscillator
8.3.2
READING AND WRITING TMR1 IN
ASYNCHRONOUS COUNTER MODE
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
A crystal oscillator circuit is built in-between pins T1OSI
(input) and T1OSO (amplifier output). It is enabled by
setting control bit T1OSCEN (T1CON<3>). The oscilla-
tor is a low power oscillator rated up to 200 kHz. It will
continue to run during SLEEP. It is primarily intended
for a 32 kHz crystal. Table 8-1 shows the capacitor
selection for the Timer1 oscillator.
Reading TMR1H or TMR1L, while the timer is running
from an external asynchronous clock, will ensure a
valid read (taken care of in hardware). However, the
user should keep in mind that reading the 16-bit timer
in two 8-bit values itself poses certain problems since
the timer may overflow between the reads.
For writes, it is recommended that the user simply stop
the timer and write the desired values. A write conten-
tion may occur by writing to the timer registers while the
register is incrementing. This may produce an unpre-
dictable value in the timer register.
The Timer1 oscillator is identical to the LP oscillator.
The user must allow a software time delay to ensure
proper oscillator start-up.
TABLE 8-1:
CAPACITOR SELECTION
FOR THE TIMER1
OSCILLATOR
Reading the 16-bit value requires some care.
Example 8-1 is an example routine to read the 16-bit
timer value. This is useful if the timer cannot be
stopped.
Osc Type
Freq
C1
C2
LP
32 kHz
100 kHz
200 kHz
33 pF
15 pF
15 pF
33 pF
15 pF
15 pF
These values are for design guidance only.
Crystals Tested:
32.768 kHz Epson C-001R32.768K-A ± 20 PPM
100 kHz
200 kHz
Epson C-2 100.00 KC-P
STD XTL 200.000 kHz
± 20 PPM
± 20 PPM
Note 1: Higher capacitance increases the stability
of oscillator but also increases the start-up
time.
2: Since each resonator/crystal has its own
characteristics, the user should consult the
resonator/crystal manufacturer for appropri-
ate values of external components.
1997 Microchip Technology Inc.
DS30234D-page 73
PIC16C6X
8.5
Resetting Timer1 using a CCP Trigger
Output
8.6
Resetting of TMR1 Register Pair
(TMR1H:TMR1L)
Applicable Devices
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
CCP2 is implemented on the PIC16C63/R63/65/65A/
R65/66/67 only.
The TMR1H and TMR1L registers are not reset to 00h
on a POR or any other reset except by the CCP1 or
CCP2 special event trigger.
If CCP1 or CCP2 module is configured in Compare
mode to generate
(CCPxM3:CCPxM0 = 1011), this signal will reset
Timer1.
a
“special event trigger”
The T1CON register is reset to 00h on a Power-on
Reset or a Brown-out Reset, which shuts off the timer
and leaves a 1:1 prescaler. In all other resets, the reg-
ister is unaffected.
Note: The “special event trigger” from the
CCP1and CCP2 modules will not set inter-
rupt flag bit TMR1IF(PIR1<0>).
8.7
Timer1 Prescaler
Applicable Devices
Timer1 must be configured for either timer or synchro-
nized counter mode to take advantage of this feature.
If the Timer1 is running in asynchronous counter mode,
this reset operation may not work.
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The prescaler counter is cleared on writes to the
TMR1H or TMR1L registers.
In the event that a write to Timer1 coincides with a spe-
cial event trigger from CCP1 or CCP2, the write will
take precedence.
In this mode of operation, the CCPRxH:CCPRxL regis-
ters pair effectively becomes the period register for the
Timer1 module.
TABLE 8-2:
REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER
Value on:
POR,
BOR
Value on
all other
resets
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0000 000x 0000 000u
0Bh,8Bh
INTCON
GIE
PEIE
T0IE
INTE
RBIE
T0IF
INTF
RBIF
10Bh,18Bh
(2)
(3)
(3)
(1)
(1)
0000 0000 0000 0000
0000 0000 0000 0000
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
--00 0000 --uu uuuu
0Ch
8Ch
0Eh
0Fh
10h
PIR1
PIE1
PSPIF
PSPIE
RCIF
RCIE
TXIF
TXIE
SSPIF
SSPIE
CCP1IF TMR2IF TMR1IF
CCP1IE TMR2IE TMR1IE
(2)
(1)
(1)
TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register
TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1 register
T1CON
—
—
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON
Legend: x= unknown, u= unchanged, -= unimplemented read as '0'. Shaded cells are not used by the Timer1 module.
Note 1: The USART is implemented on the PIC16C63/R63/65/65A/R65/66/67 only.
2: Bits PSPIE and PSPIF are reserved on the PIC16C62/62A/R62/63/R63/66, always maintain these bits clear.
3: PIR1<6> and PIE1<6> are reserved, always maintain these bits clear.
DS30234D-page 74
1997 Microchip Technology Inc.
PIC16C6X
9.1
Timer2 Prescaler and Postscaler
9.0
TIMER2 MODULE
Applicable Devices
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The prescaler and postscaler counters are cleared
when any of the following occurs:
Timer2 is an 8-bit timer with a prescaler and a
postscaler. It is especially suitable as PWM time-base
for PWM mode of CCP module(s). TMR2 is a readable
and writable register, and is cleared on any device
reset.
• a write to the TMR2 register
• a write to the T2CON register
• any device reset (POR, BOR, MCLR Reset, or
WDT Reset).
The input clock (FOSC/4) has a prescale option of 1:1,
1:4
or
1:16,
selected
by
control
bits
TMR2 is not cleared when T2CON is written.
T2CKPS1:T2CKPS0 (T2CON<1:0>).
9.2
Output of TMR2
The Timer2 module has an 8-bit period register, PR2.
Timer2 increments from 00h until it matches PR2 and
then resets to 00h on the next increment cycle. PR2 is
a readable and writable register.The PR2 register is ini-
tialized to FFh upon reset.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The output of TMR2 (before the postscaler) is fed to the
Synchronous Serial Port module which optionally uses
it to generate shift clock.
The match output of the TMR2 register goes through a
4-bit postscaler (which gives a 1:1 to 1:16 scaling,
inclusive) to generate a TMR2 interrupt (latched in flag
bit TMR2IF (PIR1<1>)).
FIGURE 9-1: TIMER2 BLOCK DIAGRAM
Sets
TMR2
TMR2
output(1)
The Timer2 module can be shut off by clearing control
bit TMR2ON (T2CON<2>) to minimize power con-
sumption.
interrupt
flag bit,
TMR2IF
Reset
Prescaler
1:1, 1:4, 1:16
TMR2 reg
Fosc/4
Figure 9-2 shows the Timer2 control register.T2CON is
cleared upon reset which initializes Timer2 as shut off
with the prescaler and postscaler at a 1:1 value.
Postscaler
1:1 to 1:16
2
Comparator
EQ
4
PR2 reg
Note 1: TMR2 register output can be software selected by
the SSP Module as a baud clock.
FIGURE 9-2: T2CON: TIMER2 CONTROL REGISTER (ADDRESS 12h)
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0
bit0
R
= Readable bit
W = Writable bit
U
bit7
= Unimplemented bit,
read as ‘0’
- n = Value at POR reset
bit 7:
Unimplemented: Read as '0'
bit 6-3: TOUTPS3:TOUTPS0: Timer2 Output Postscale Select bits
0000= 1:1 postscale
0001= 1:2 postscale
•
•
1111= 1:16 postscale
bit 2:
TMR2ON: Timer2 On bit
1 = Timer2 is on
0 = Timer2 is off
bit 1-0: T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits
00= 1:1 prescale
01= 1:4 prescale
1x= 1:16 prescale
1997 Microchip Technology Inc.
DS30234D-page 75
PIC16C6X
TABLE 9-1:
REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER
Value on:
POR,
BOR
Value on
all other
resets
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0Bh,8Bh
INTCON
GIE
PEIE
T0IE
INTE
RBIE
T0IF
INTF
RBIF
0000 000x 0000 000u
10Bh,18Bh
(2)
(3)
(3)
(1)
(1)
0Ch
8Ch
11h
12h
92h
PIR1
PSPIF
PSPIE
RCIF
RCIE
TXIF
TXIE
SSPIF
CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
(2)
(1)
(1)
PIE1
SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
TMR2
T2CON
PR2
Timer2 module’s register
0000 0000 0000 0000
—
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000
Timer2 Period register 1111 1111 1111 1111
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0'. Shaded cells are not used by Timer2.
Note 1: The USART is implemented on the PIC16C63/R63/65/65A/R65/66/67 only.
2: Bits PSPIE and PSPIF are reserved on the PIC16C62/62A/R62/63/R63/66, always maintain these bits clear.
3: PIR1<6> and PIE1<6> are reserved, always maintain these bits clear.
DS30234D-page 76
1997 Microchip Technology Inc.
PIC16C6X
CCP2 module:
10.0 CAPTURE/COMPARE/PWM
(CCP) MODULE(s)
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67 CCP1
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67 CCP2
Capture/Compare/PWM Register2 (CCPR2) is com-
prised of two 8-bit registers: CCPR2L (low byte) and
CCPR2H (high byte). The CCP2CON register controls
the operation of CCP2. All are readable and writable.
For use of the CCP modules, refer to the Embedded
Control Handbook, “Using the CCP Modules” (AN594).
Each CCP (Capture/Compare/PWM) module contains
a 16-bit register which can operate as a 16-bit capture
register, as a 16-bit compare register, or as a PWM
master/slave duty cycle register. Both the CCP1 and
CCP2 modules are identical in operation, with the
exception of the operation of the special event trigger.
Table 10-1 and Table 10-2 show the resources and
interactions of the CCP modules(s). In the following
sections, the operation of a CCP module is described
with respect to CCP1. CCP2 operates the same as
CCP1, except where noted.
TABLE 10-1: CCP MODE - TIMER
RESOURCE
CCP Mode
Timer Resource
Capture
Compare
PWM
Timer1
Timer1
Timer2
CCP1 module:
Capture/Compare/PWM Register1 (CCPR1) is com-
prised of two 8-bit registers: CCPR1L (low byte) and
CCPR1H (high byte). The CCP1CON register controls
the operation of CCP1. All are readable and writable.
TABLE 10-2: INTERACTION OF TWO CCP MODULES
CCPx Mode CCPy Mode
Interaction
Capture
Capture
Compare
PWM
Capture
Compare
Compare
PWM
Same TMR1 time-base.
The compare should be configured for the special event trigger, which clears TMR1.
The compare(s) should be configured for the special event trigger, which clears TMR1.
The PWMs will have the same frequency, and update rate (TMR2 interrupt).
PWM
Capture
Compare
None
None
PWM
1997 Microchip Technology Inc.
DS30234D-page 77
PIC16C6X
FIGURE 10-1: CCP1CON REGISTER (ADDRESS 17h) / CCP2CON REGISTER (ADDRESS 1Dh)
U-0
—
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CCPxX CCPxY CCPxM3 CCPxM2 CCPxM1 CCPxM0
bit0
R = Readable bit
W = Writable bit
bit7
U = Unimplemented bit,
read as ‘0’
- n =Value at POR reset
bit 7-6: Unimplemented: Read as '0'
bit 5-4: CCPxX:CCPxY: PWM Least Significant bits
Capture Mode
Unused
Compare Mode
Unused
PWM Mode
These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPRxL.
bit 3-0: CCPxM3:CCPxM0: CCPx Mode Select bits
0000= Capture/Compare/PWM off (resets CCPx module)
0100= Capture mode, every falling edge
0101= Capture mode, every rising edge
0110= Capture mode, every 4th rising edge
0111= Capture mode, every 16th rising edge
1000= Compare mode, set output on match (bit CCPxIF is set)
1001= Compare mode, clear output on match (bit CCPxIF is set)
1010= Compare mode, generate software interrupt on match (bit CCPxIF is set, CCPx pin is unaffected)
1011= Compare mode, trigger special event (CCPxIF bit is set; CCP1 resets TMR1; CCP2 resets TMR1)
11xx= PWM mode
10.1
Capture Mode
FIGURE 10-2: CAPTURE MODE
OPERATION BLOCK
DIAGRAM
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
In Capture mode, CCPR1H:CCPR1L captures the
16-bit value of the TMR1 register when an event occurs
on pin RC2/CCP1 (Figure 10-2). An event is defined as:
Set CCP1IF
PIR1<2>
Prescaler
÷ 1, 4, 16
RC2/CCP1
pin
CCPR1H
CCPR1L
TMR1L
• Every falling edge
• Every rising edge
Capture
Enable
and
edge detect
• Every 4th rising edge
• Every 16th rising edge
TMR1H
CCP1CON<3:0>
An event is selected by control bits CCP1M3:CCP1M0
(CCP1CON<3:0>). When a capture is made, the inter-
rupt request flag bit CCP1IF (PIR1<2>) is set. It must
be cleared in software. If another capture occurs before
the value in register CCPR1 is read, the old captured
value will be lost.
Q’s
10.1.2 TIMER1 MODE SELECTION
Timer1 must be running in Timer mode or Synchro-
nized Counter mode for the CCP module to use the
capture feature. In Asynchronous Counter mode, the
capture operation may not work consistently.
10.1.1 CCP PIN CONFIGURATION
In Capture mode, the RC2/CCP1 pin should be config-
ured as an input by setting the TRISC<2> bit.
10.1.3 SOFTWARE INTERRUPT
Note: If the RC2/CCP1 pin is configured as an
output, a write to PORTC can cause a cap-
ture condition.
When the Capture event is changed, a false capture
interrupt may be generated. The user should clear
enable bit CCP1IE (PIE1<2>) to avoid false interrupts
and should clear flag bit CCP1IF following any such
change in operating mode.
DS30234D-page 78
1997 Microchip Technology Inc.
PIC16C6X
10.1.4 CCP PRESCALER
10.2.1 CCP PIN CONFIGURATION
There are four prescaler settings, specified by bits
CCP1M3:CCP1M0. Whenever the CCP module is
turned off, or the CCP module is not in Capture mode,
the prescaler counter is cleared. This means that any
reset will clear the prescaler counter.
The user must configure the RC2/CCP1 pin as an out-
put by clearing the TRISC<2> bit.
Note: Clearing the CCP1CON register will force
the RC2/CCP1 compare output latch to the
default low level. This is not the data latch.
Switching from one capture prescaler to another may
generate an interrupt. Also, the prescaler counter will
not be cleared, therefore the first capture may be from
a non-zero prescaler. Example 10-1 shows the recom-
mended method for switching between capture pres-
calers. This example also clears the prescaler counter
and will not generate the “false” interrupt.
10.2.1 TIMER1 MODE SELECTION
Timer1 must be running in Timer mode or Synchro-
nized Counter mode if the CCP module is using the
compare feature. In Asynchronous Counter mode, the
compare operation may not work.
10.2.2 SOFTWARE INTERRUPT MODE
EXAMPLE 10-1: CHANGING BETWEEN
CAPTURE PRESCALERS
When Generate Software Interrupt is chosen, the
CCP1 pin is not affected. Only a CCP interrupt is gen-
erated (if enabled).
CLRF
CCP1CON
; Turn CCP module off
MOVLW NEW_CAPT_PS ; Load the W reg with
; the new prescaler
10.2.3 SPECIAL EVENT TRIGGER
; mode value and CCP ON
MOVWF CCP1CON
; Load CCP1CON with
; this value
In this mode, an internal hardware trigger is generated
which may be used to initiate an action.
The special event trigger output of CCP1 and CCP2
resets the TMR1 register pair. This allows the
CCPR1H:CCPR1L and CCPR2H:CCPR2L registers to
effectively be 16-bit programmable period register(s)
for Timer1.
10.2
Compare Mode
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
In Compare mode, the 16-bit CCPR1 register value is
constantly compared against the TMR1 register pair
value. When a match occurs, the RC2/CCP1 pin is:
For compatibility issues, the special event trigger out-
put of CCP1 (PIC16C72) and CCP2 (all other
PIC16C7X devices) also starts an A/D conversion.
• Driven High
• Driven Low
Note: The “special event trigger” from the
CCP1and CCP2 modules will not set inter-
rupt flag bit TMR1IF (PIR1<0>).
• Remains Unchanged
The action on the pin is based on the value of control
bits CCP1M3:CCP1M0 (CCP1CON<3:0>). At the
same time interrupt flag bit CCP1IF is set.
FIGURE 10-3: COMPARE MODE
OPERATION BLOCK
DIAGRAM
Special event trigger will reset Timer1, but not
set interrupt flag bit TMR1IF (PIR1<0>).
Special Event Trigger
Set CCP1IF
PIR1<2>
CCPR1H CCPR1L
Q
S
R
Output
Logic
Comparator
match
RC2/CCP1
TRISC<2>
Output Enable
TMR1H TMR1L
CCP1CON<3:0>
Mode Select
1997 Microchip Technology Inc.
DS30234D-page 79
PIC16C6X
10.3.1 PWM PERIOD
10.3
PWM Mode
Applicable Devices
The PWM period is specified by writing to the PR2 reg-
ister. The PWM period can be calculated using the fol-
lowing formula:
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
In Pulse Width Modulation (PWM) mode, the CCP1 pin
produces up to a 10-bit resolution PWM output. Since
the CCP1 pin is multiplexed with the PORTC data latch,
the TRISC<2> bit must be cleared to make the CCP1
pin an output.
PWM period = [(PR2) + 1] • 4 • TOSC •
(TMR2 prescale value)
PWM frequency is defined as 1 / [PWM period].
When TMR2 is equal to PR2, the following three events
occur on the next increment cycle:
Note: Clearing the CCP1CON register will force
the CCP1 PWM output latch to the default
low level. This is not the PORTC I/O data
latch.
• TMR2 is cleared
• The PWM duty cycle is latched from CCPR1L into
CCPR1H
Figure 10-4 shows a simplified block diagram of the
CCP module in PWM mode.
• The CCP1 pin is set (exception: if PWM duty
cycle = 0%, the CCP1 pin will not be set)
For a step by step procedure on how to set up the CCP
module for PWM operation, see Section 10.3.3.
Note: The Timer2 postscaler (see Section 9.1) is
not used in the determination of the PWM
frequency.The postscaler could be used to
have a servo update rate at a different fre-
quency than the PWM output.
FIGURE 10-4: SIMPLIFIED PWM BLOCK
DIAGRAM
CCP1CON<5:4>
Duty cycle registers
CCPR1L
10.3.2 PWM DUTY CYCLE
The PWM duty cycle is specified by writing to the
CCPR1L register and to the CCP1CON<5:4> bits. Up
to 10-bit resolution is available: the CCPR1L contains
the eight MSbs and the CCP1CON<5:4> contains the
two LSbs. This 10-bit value is represented by
CCPR1L:CCP1CON<5:4>. The following equation is
used to calculate the PWM duty cycle in time:
CCPR1H (Slave)
Q
R
S
Comparator
TMR2
RC2/CCP1
(Note 1)
PWM duty cycle = (CCPR1L:CCP1CON<5:4>) •
Tosc • (TMR2 prescale value)
TRISC2
Comparator
CCPR1L and CCP1CON<5:4> can be written to at any
time, but the duty cycle value is not latched into
CCPR1H until after a match between PR2 and TMR2
occurs (i.e., the period is complete). In PWM mode,
CCPR1H is a read-only register.
Clear Timer,
CCP1 pin and
latch D.C.
PR2
Note 1: 8-bit timer is concatenated with 2-bit internal Q clock
or 2 bits of the prescaler to create 10-bit time-base.
The CCPR1H register and a 2-bit internal latch are
used to double buffer the PWM duty cycle. This double
buffering is essential for glitchless PWM operation.
A PWM output (Figure 10-5) has a time base (period)
and a time that the output stays high (duty cycle). The
frequency of the PWM is the inverse of the period
(1/period).
When the CCPR1H and 2-bit latch match TMR2 con-
catenated with an internal 2-bit Q clock or 2 bits of the
TMR2 prescaler, the CCP1 pin is cleared.
FIGURE 10-5: PWM OUTPUT
Maximum PWM resolution (bits) for a given PWM
frequency:
Period
FOSC
log(
)
FPWM
=
bits
log(2)
Duty Cycle
TMR2 = PR2
Note: If the PWM duty cycle value is longer than
the PWM period the CCP1 pin will not be
forced to the low level.
TMR2 = Duty Cycle
TMR2 = PR2
DS30234D-page 80
1997 Microchip Technology Inc.
PIC16C6X
In order to achieve higher resolution, the PWM fre-
quency must be decreased. In order to achieve higher
PWM frequency, the resolution must be decreased.
EXAMPLE 10-2: PWM PERIOD AND DUTY
CYCLE CALCULATION
Desired PWM frequency is 78.125 kHz,
Fosc = 20 MHz
TMR2 prescale = 1
Table 10-3 lists example PWM frequencies and resolu-
tions for Fosc = 20 MHz. The TMR2 prescaler and PR2
values are also shown.
1/78.125 kHz = [(PR2) + 1] • 4 • 1/20 MHz • 1
10.3.3 SET-UP FOR PWM OPERATION
12.8 µs
= [(PR2) + 1] • 4 • 50 ns • 1
= 63
PR2
The following steps should be taken when configuring
the CCP module for PWM operation:
Find the maximum resolution of the duty cycle that can
be used with a 78.125 kHz frequency and 20 MHz
oscillator:
1. Set the PWM period by writing to the PR2 regis-
ter.
1/78.125 kHz = 2PWM RESOLUTION • 1/20 MHz • 1
2. Set the PWM duty cycle by writing to the
CCPR1L register and CCP1CON<5:4> bits.
12.8 µs
256
= 2PWM RESOLUTION • 50 ns • 1
= 2PWM RESOLUTION
3. Make the CCP1 pin an output by clearing the
TRISC<2> bit.
log(256)
8.0
= (PWM Resolution) • log(2)
= PWM Resolution
4. Set the TMR2 prescale value and enable Timer2
by writing to T2CON.
5. Configure the CCP1 module for PWM operation.
At most, an 8-bit resolution duty cycle can be obtained
from a 78.125 kHz frequency and a 20 MHz oscillator,
i.e., 0 ≤ CCPR1L:CCP1CON<5:4> ≤ 255. Any value
greater than 255 will result in a 100% duty cycle.
TABLE 10-3: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 20 MHz
PWM Frequency
Timer Prescaler (1, 4, 16)
1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz
16
0xFF
10
4
1
1
0x3F
8
1
0x1F
7
1
PR2 Value
0xFF
10
0xFF
10
0x17
5.5
Maximum Resolution (bits)
TABLE 10-4: REGISTERS ASSOCIATED WITH TIMER1, CAPTURE AND COMPARE
Value on:
POR,
BOR
Value on
all other
Resets
Add
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0000 000x 0000 000u
0Bh,8Bh
INTCON
GIE
PEIE
T0IE
INTE
RBIE
T0IF
INTF
RBIF
10Bh,18Bh
(2)
(3)
(1)
(1)
0Ch
PIR1
PSPIF
—
RCIF
—
TXIF
—
SSPIF
—
CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
CCP2IF ---- ---0 ---- ---0
CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
(4)
0Dh
PIR2
—
—
—
(2)
(3)
(1)
(1)
8Ch
PIE1
PSPIE
—
RCIE
—
TXIE
—
SSPIE
—
(4)
8Dh
PIE2
—
—
—
CCP2IE ---- ---0 ---- ---0
1111 1111 1111 1111
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
87h
0Eh
0Fh
10h
15h
16h
17h
TRISC
TMR1L
TMR1H
T1CON
PORTC Data Direction register
Holding register for the Least Significant Byte of the 16-bit TMR1 register
Holding register for the Most Significant Byte of the 16-bit TMR1 register
—
—
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu
CCPR1L Capture/Compare/PWM1 (LSB)
CCPR1H Capture/Compare/PWM1 (MSB)
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
CCP1CON
—
—
CCP1X
CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
xxxx xxxx uuuu uuuu
(4)
1Bh
CCPR2L Capture/Compare/PWM2 (LSB)
CCPR2H Capture/Compare/PWM2 (MSB)
(4)
1Ch
xxxx xxxx uuuu uuuu
(4)
1Dh
CCP2CON
—
—
CCP2X
CCP2Y CCP2M3 CCP2M2 CCP2M1 CCP2M0 --00 0000 --00 0000
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0’. Shaded cells are not used in these modes.
Note 1: These bits are associated with the USART module, which is implemented on the PIC16C63/R63/65/65A/R65/66/67 only.
2: Bits PSPIE and PSPIF are reserved on the PIC16C62/62A/R62/63/R63/66, always maintain these bits clear.
3: The PIR1<6> and PIE1<6> bits are reserved, always maintain these bits clear.
4: These registers are associated with the CCP2 module, which is only implemented on the PIC16C63/R63/65/65A/R65/66/67.
1997 Microchip Technology Inc.
DS30234D-page 81
PIC16C6X
TABLE 10-5: REGISTERS ASSOCIATED WITH PWM AND TIMER2
Value on: Value on
Addr
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
POR,
BOR
all other
Resets
0Bh,8Bh
INTCON
GIE
PEIE
T0IE
INTE
RBIE
T0IF
INTF
RBIF 0000000x 0000000u
10Bh,18Bh
(2)
(3)
(1)
(1)
0Ch
PIR1
PIR2
PIE1
PSPIF
—
RCIF
—
TXIF
—
SSPIF
—
CCP1IF TMR2IF TMR1IF 00000000 00000000
CCP2IF -------0 -------0
CCP1IE TMR2IE TMR1IE 00000000 00000000
(4)
0Dh
—
—
—
(2)
(3)
(1)
(1)
8Ch
PSPIE
—
RCIE
—
TXIE
—
SSPIE
—
(4)
8Dh
PIE2
—
—
—
CCP2IE -------0 -------0
87h
11h
92h
12h
15h
16h
17h
TRISC
PORTC Data Direction register
Timer2 module’s register
11111111 11111111
TMR2
00000000 00000000
11111111 11111111
PR2
Timer2 module’s Period register
T2CON
—
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -0000000 -0000000
Capture/Compare/PWM1 (LSB)
Capture/Compare/PWM1 (MSB)
CCPR1L
CCPR1H
CCP1CON
CCPR2L
CCPR2H
CCP2CON
xxxxxxxx uuuuuuuu
xxxxxxxx uuuuuuuu
—
—
CCP1X
CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0 --000000 --000000
xxxxxxxx uuuuuuuu
(4)
Capture/Compare/PWM2 (LSB)
Capture/Compare/PWM2 (MSB)
1Bh
(4)
1Ch
xxxxxxxx uuuuuuuu
(4)
1Dh
—
—
CCP2X
CCP2Y CCP2M3 CCP2M2 CCP2M1 CCP2M0 --000000 --000000
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0’. Shaded cells are not used in this mode.
Note 1: These bits are associated with the USART module, which is implemented on the PIC16C63/R63/65/65A/R65/66/67 only.
2: Bits PSPIE and PSPIF are reserved on the PIC16C62/62A/R62/63/R63/66, always maintain these bits clear.
3: The PIR1<6> and PIE1<6> bits are reserved, always maintain these bits clear.
4: These registers are associated with the CCP2 module, which is only implemented on the PIC16C63/R63/65/65A/R65/66/67.
DS30234D-page 82
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
11.0 SYNCHRONOUS SERIAL
PORT (SSP) MODULE
11.1
SSP Module Overview
The Synchronous Serial Port (SSP) module is a serial
interface useful for communicating with other peripheral
or microcontroller devices. These peripheral devices
may be Serial EEPROMs, shift registers, display driv-
ers, A/D converters, etc. The SSP module can operate
in one of two modes:
• Serial Peripheral Interface (SPI)
• Inter-Integrated Circuit (I2C)
2
The SSP module in I C mode works the same in all
PIC16C6X devices that have an SSP module. However
the SSP Module in SPI mode has differences between
the PIC16C66/67 and the other PIC16C6X devices.
The register definitions and operational description of
SPI mode has been split into two sections because of
the differences between the PIC16C66/67 and the
other PIC16C6X devices. The default reset values of
both the SPI modules is the same regardless of the
device:
11.2 SPI Mode for PIC16C62/62A/R62/63/R63/64/
64A/R64/65/65A/R65 .......................................84
11.3 SPI Mode for PIC16C66/67..............................89
11.4 I2C™ Overview ................................................95
11.5 SSP I2C Operation...........................................99
Refer to Application Note AN578,“Use of the SSP Mod-
2
ule in the I C Multi-Master Environment.”
1997 Microchip Technology Inc.
DS30234D-page 83
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
11.2
SPI Mode for PIC16C62/62A/R62/63/
R63/64/64A/R64/65/65A/R65
This section contains register definitions and opera-
tional characteristics of the SPI module for the
PIC16C62, PIC16C62A, PIC16CR62, PIC16C63,
PIC16CR63, PIC16C64, PIC16C64A, PIC16CR64,
PIC16C65, PIC16C65A, PIC16CR65.
FIGURE 11-1: SSPSTAT: SYNC SERIAL PORT STATUS REGISTER (ADDRESS 94h)
U-0
—
U-0
—
R-0
D/A
R-0
P
R-0
S
R-0
R-0
UA
R-0
BF
R/W
R = Readable bit
W = Writable bit
bit7
bit0
U = Unimplemented bit,
read as ‘0’
- n =Value at POR reset
bit 7-6: Unimplemented: Read as '0'
2
bit 5:
bit 4:
bit 3:
bit 2:
D/A: Data/Address bit (I C mode only)
1 = Indicates that the last byte received or transmitted was data
0 = Indicates that the last byte received or transmitted was address
2
P: Stop bit (I C mode only. This bit is cleared when the SSP module is disabled, SSPEN is cleared)
1 = Indicates that a stop bit has been detected last (this bit is '0' on RESET)
0 = Stop bit was not detected last
2
S: Start bit (I C mode only. This bit is cleared when the SSP module is disabled, SSPEN is cleared)
1 = Indicates that a start bit has been detected last (this bit is '0' on RESET)
0 = Start bit was not detected last
2
R/W: Read/Write bit information (I C mode only)
This bit holds the R/W bit information following the last address match. This bit is valid from the address
match to the next start bit, stop bit, or ACK bit.
1 = Read
0 = Write
2
bit 1:
bit 0:
UA: Update Address (10-bit I C mode only)
1 = Indicates that the user needs to update the address in the SSPADD register
0 = Address does not need to be updated
BF: Buffer Full Status bit
2
Receive (SPI and I C modes)
1 = Receive complete, SSPBUF is full
0 = Receive not complete, SSPBUF is empty
2
Transmit (I C mode only)
1 = Transmit in progress, SSPBUF is full
0 = Transmit complete, SSPBUF is empty
DS30234D-page 84
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
FIGURE 11-2: SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS 14h)
R/W-0
R/W-0
R/W-0
R/W-0
CKP
R/W-0
R/W-0
R/W-0
R/W-0
WCOL SSPOV SSPEN
bit7
SSPM3 SSPM2 SSPM1 SSPM0
bit0
R = Readable bit
W = Writable bit
U = Unimplemented bit,
read as ‘0’
- n =Value at POR reset
bit 7:
WCOL: Write Collision Detect bit
1 = The SSPBUF register is written while it is still transmitting the previous word
(must be cleared in software)
0 = No collision
bit 6:
SSPOV: Receive Overflow Detect bit
In SPI mode
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow,
the data in SSPSR register is lost. Overflow can only occur in slave mode. The user must read the SSP-
BUF, even if only transmitting data, to avoid setting overflow. In master mode the overflow bit is not set
since each new reception (and transmission) is initiated by writing to the SSPBUF register.
0 = No overflow
2
In I C mode
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don’t care"
in transmit mode. SSPOV must be cleared in software in either mode.
0 = No overflow
bit 5:
SSPEN: Synchronous Serial Port Enable bit
In SPI mode
1 = Enables serial port and configures SCK, SDO, and SDI as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
2
In I C mode
1 = Enables the serial port and configures the SDA and SCL pins as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
In both modes, when enabled, these pins must be properly configured as input or output.
bit 4:
CKP: Clock Polarity Select bit
In SPI mode
1 = Idle state for clock is a high level. Transmit happens on falling edge, receive on rising edge.
0 = Idle state for clock is a low level. Transmit happens on rising edge, receive on falling edge.
2
In I C mode
SCK release control
1 = Enable clock
0 = Holds clock low (clock stretch) (Used to ensure data setup time)
bit 3-0: SSPM3:SSPM0: Synchronous Serial Port Mode Select bits
0000= SPI master mode, clock = Fosc/4
0001= SPI master mode, clock = Fosc/16
0010= SPI master mode, clock = Fosc/64
0011= SPI master mode, clock = TMR2 output/2
0100= SPI slave mode, clock = SCK pin. SS pin control enabled.
0101= SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin.
2
0110= I C slave mode, 7-bit address
2
0111= I C slave mode, 10-bit address
2
1011= I C firmware controlled Master Mode (slave idle)
2
1110= I C slave mode, 7-bit address with start and stop bit interrupts enabled
2
1111= I C slave mode, 10-bit address with start and stop bit interrupts enabled
1997 Microchip Technology Inc.
DS30234D-page 85
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
11.2.1 OPERATION OF SSP MODULE IN SPI
MODE
EXAMPLE 11-1: LOADING THE SSPBUF
(SSPSR) REGISTER
BSF
STATUS, RP0
;Specify Bank 1
;Has data been
;received
Applicable Devices
LOOP BTFSS SSPSTAT, BF
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
;(transmit
;complete)?
;No
;Specify Bank 0
;W reg = contents
;of SSPBUF
;Save in user RAM
;W reg = contents
; of TXDATA
The SPI mode allows 8-bits of data to be synchro-
nously transmitted and received simultaneously. To
accomplish communication, typically three pins are
used:
GOTO LOOP
BCF
STATUS, RP0
MOVF SSPBUF, W
• Serial Data Out (SDO)
• Serial Data In (SDI)
• Serial Clock (SCK)
MOVWF RXDATA
MOVF TXDATA, W
Additionally a fourth pin may be used when in a slave
mode of operation:
MOVWF SSPBUF
;New data to xmit
The block diagram of the SSP module, when in SPI
mode (Figure 11-3), shows that the SSPSR register is
not directly readable or writable, and can only be
accessed from addressing the SSPBUF register. Addi-
tionally, the SSP status register (SSPSTAT) indicates
the various status conditions.
• Slave Select (SS)
When initializing the SPI, several options need to be
specified.This is done by programming the appropriate
control bits in the SSPCON register (SSPCON<5:0>).
These control bits allow the following to be specified:
• Master Mode (SCK is the clock output)
• Slave Mode (SCK is the clock input)
FIGURE 11-3: SSP BLOCK DIAGRAM
(SPI MODE)
• Clock Polarity (Output/Input data on the Rising/
Falling edge of SCK)
• Clock Rate (Master mode only)
Internal
data bus
• Slave Select Mode (Slave mode only)
The SSP consists of a transmit/receive Shift Register
(SSPSR) and a Buffer register (SSPBUF). The SSPSR
shifts the data in and out of the device, MSb first. The
SSPBUF holds the data that was written to the SSPSR,
until the received data is ready. Once the 8-bits of data
have been received, that byte is moved to the SSPBUF
register. Then the Buffer Full bit, BF (SSPSTAT<0>)
and flag bit SSPIF are set. This double buffering of the
received data (SSPBUF) allows the next byte to start
reception before reading the data that was just
received. Any write to the SSPBUF register during
transmission/reception of data will be ignored, and the
write collision detect bit, WCOL (SSPCON<7>) will be
set. User software must clear bit WCOL so that it can
be determined if the following write(s) to the SSPBUF
completed successfully. When the application software
is expecting to receive valid data, the SSPBUF register
should be read before the next byte of data to transfer
is written to the SSPBUF register.The Buffer Full bit BF
(SSPSTAT<0>) indicates when the SSPBUF register
has been loaded with the received data (transmission
is complete). When the SSPBUF is read, bit BF is
cleared. This data may be irrelevant if the SPI is only a
transmitter. Generally the SSP Interrupt is used to
determine when the transmission/reception has com-
pleted. The SSPBUF register must be read and/or writ-
ten. If the interrupt method is not going to be used, then
software polling can be done to ensure that a write col-
lision does not occur. Example 11-1 shows the loading
of the SSPBUF (SSPSR) register for data transmis-
sion. The shaded instruction is only required if the
received data is meaningful.
Read
Write
SSPBUF reg
SSPSR reg
shift
clock
RC4/SDI/SDA
RC5/SDO
bit0
Control
Enable
SS
RA5/SS
Edge
Select
2
Clock Select
SSPM3:SSPM0
4
TMR2 output
2
Edge
Select
TCY
Prescaler
4, 16, 64
RC3/SCK/
SCL
TRISC<3>
DS30234D-page 86
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
To enable the serial port, SSP enable bit SSPEN
(SSPCON<5>) must be set.To reset or reconfigure SPI
mode, clear enable bit SSPEN, re-initialize SSPCON
register, and then set enable bit SSPEN. This config-
ures the SDI, SDO, SCK, and SS pins as serial port
pins. For the pins to behave as the serial port function,
they must have their data direction bits (in the TRIS reg-
ister) appropriately programmed. That is:
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 2) is to broadcast data by
the software protocol.
In master mode the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SCK output could be disabled
(programmed as an input). The SSPSR register will
continue to shift in the signal present on the SDI pin at
the programmed clock rate. As each byte is received, it
will be loaded into the SSPBUF register as if a normal
received byte (interrupts and status bits appropriately
set). This could be useful in receiver applications as a
“line activity monitor” mode.
• SDI must have TRISC<4> set
• SDO must have TRISC<5> cleared
• SCK (Master mode) must have TRISC<3>
cleared
• SCK (Slave mode) must have TRISC<3> set
• SS must have TRISA<5> set (if implemented)
In slave mode, the data is transmitted and received as
the external clock pulses appear on SCK. When the
last bit is latched interrupt flag bit SSPIF (PIR1<3>) is
set.
Any serial port function that is not desired may be over-
ridden by programming the corresponding data direc-
tion (TRIS) register to the opposite value. An example
would be in master mode where you are only sending
data (to a display driver), then both SDI and SS could
be used as general purpose outputs by clearing their
corresponding TRIS register bits.
The clock polarity is selected by appropriately program-
ming bit CKP (SSPCON<4>). This then would give
waveforms for SPI communication as shown in
Figure 11-5 and Figure 11-6 where the MSB is trans-
mitted first. In master mode, the SPI clock rate (bit rate)
is user programmable to be one of the following:
Figure 11-4 shows a typical connection between two
microcontrollers. The master controller (Processor 1)
initiates the data transfer by sending the SCK signal.
Data is shifted out of both shift registers on their pro-
grammed clock edge, and latched on the opposite edge
of the clock. Both processors should be programmed to
the same Clock Polarity (CKP), then both controllers
would send and receive data at the same time.
Whether the data is meaningful (or dummy data)
depends on the application software. This leads to
three scenarios for data transmission:
• Fosc/4 (or TCY)
• Fosc/16 (or 4 • TCY)
• Fosc/64 (or 16 • TCY)
• Timer2 output/2
This allows a maximum bit clock frequency (at 20 MHz)
of 5 MHz. When in slave mode the external clock must
meet the minimum high and low times.
In sleep mode, the slave can transmit and receive data
and wake the device from sleep.
• Master sends data — Slave sends dummy data
• Master sends data — Slave sends data
• Master sends dummy data — Slave sends data
FIGURE 11-4: SPI MASTER/SLAVE CONNECTION
SPI Master SSPM3:SSPM0 = 00xxb
SPI Slave SSPM3:SSPM0 = 010xb
SDO
SDI
Serial Input Buffer
(SSPBUF register)
Serial Input Buffer
(SSPBUF register)
SDI
SDO
Shift Register
Shift Register
(SSPSR)
(SSPSR)
LSb
MSb
MSb
LSb
Serial Clock
SCK
SCK
PROCESSOR 1
PROCESSOR 2
1997 Microchip Technology Inc.
DS30234D-page 87
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
The SS pin allows a synchronous slave mode. The
SPI must be in slave mode (SSPCON<3:0> = 04h)
and the TRISA<5> bit must be set the for synchro-
nous slave mode to be enabled. When the SS pin is
low, transmission and reception are enabled and
the SDO pin is driven. When the SS pin goes high,
the SDO pin is no longer driven, even if in the mid-
dle of a transmitted byte, and becomes a floating
output. If the SS pin is taken low without resetting
SPI mode, the transmission will continue from the
point at which it was taken high. External pull-up/
pull-down resistors may be desirable, depending on the
application.
To emulate two-wire communication, the SDO pin can
be connected to the SDI pin. When the SPI needs to
operate as a receiver the SDO pin can be configured as
an input. This disables transmissions from the SDO.
The SDI can always be left as an input (SDI function)
since it cannot create a bus conflict.
FIGURE 11-5: SPI MODE TIMING, MASTER MODE OR SLAVE MODE W/O SS CONTROL
SCK
(CKP = 0)
SCK
(CKP = 1)
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
bit0
SDO
SDI
bit7
SSPIF
FIGURE 11-6: SPI MODE TIMING, SLAVE MODE WITH SS CONTROL
SS
SCK
(CKP = 0)
SCK
(CKP = 1)
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
bit0
SDO
SDI
bit7
SSPIF
TABLE 11-1: REGISTERS ASSOCIATED WITH SPI OPERATION
Value on:
POR,
BOR
Value on
all other
Resets
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0Bh,8Bh INTCON
GIE
PEIE
T0IE
INTE
RBIE
T0IF
INTF
RBIF 0000 000x 0000 000u
(2)
(3)
(1)
(1)
0Ch
8Ch
13h
14h
85h
PIR1
PIE1
PSPIF
PSPIE
RCIF
RCIE
TXIF
TXIE
SSPIF CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
(2)
(3)
(1)
(1)
SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register
xxxx xxxx uuuu uuuu
SSPCON
TRISA
WCOL SSPOV SSPEN
CKP
SSPM3 SSPM2 SSPM1 SSPM0 0000 0000 0000 0000
--11 1111 --11 1111
1111 1111 1111 1111
--00 0000 --00 0000
PORTA Data Direction Register
—
—
87h
94h
TRISC
PORTC Data Direction Register
D/A
SSPSTAT
—
—
P
S
R/W
UA
BF
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0'. Shaded cells are not used by SSP module in SPI
mode.
Note 1: These bits are associated with the USART which is implemented on the PIC16C63/R63/65/65A/R65 only.
2: PSPIF and PSPIE are reserved on the PIC16C62/62A/R62/63/R63, always maintain these bits clear.
3: PIR1<6> and PIE1<6> are reserved, always maintain these bits clear.
DS30234D-page 88
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
11.3
SPI Mode for PIC16C66/67
This section contains register definitions and opera-
tional characterisitics of the SPI module on the
PIC16C66 and PIC16C67 only.
FIGURE 11-7: SSPSTAT: SYNC SERIAL PORT STATUS REGISTER (ADDRESS 94h)(PIC16C66/67)
R/W-0 R/W-0
SMP CKE
bit7
R-0
D/A
R-0
P
R-0
S
R-0
R-0
UA
R-0
BF
R/W
R = Readable bit
W = Writable bit
U = Unimplemented bit,
read as ‘0’
bit0
- n =Value at POR reset
bit 7:
bit 6:
SMP: SPI data input sample phase
SPI Master Mode
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
SPI Slave Mode
SMP must be cleared when SPI is used in slave mode
CKE: SPI Clock Edge Select (Figure 11-11, Figure 11-12, and Figure 11-13)
CKP = 0
1 = Data transmitted on rising edge of SCK
0 = Data transmitted on falling edge of SCK
CKP = 1
1 = Data transmitted on falling edge of SCK
0 = Data transmitted on rising edge of SCK
2
bit 5:
bit 4:
D/A: Data/Address bit (I C mode only)
1 = Indicates that the last byte received or transmitted was data
0 = Indicates that the last byte received or transmitted was address
2
P: Stop bit (I C mode only. This bit is cleared when the SSP module is disabled, or when the Start bit is
detected last, SSPEN is cleared)
1 = Indicates that a stop bit has been detected last (this bit is '0' on RESET)
0 = Stop bit was not detected last
2
bit 3:
bit 2:
S: Start bit (I C mode only. This bit is cleared when the SSP module is disabled, or when the Stop bit is
detected last, SSPEN is cleared)
1 = Indicates that a start bit has been detected last (this bit is '0' on RESET)
0 = Start bit was not detected last
2
R/W: Read/Write bit information (I C mode only)
This bit holds the R/W bit information following the last address match. This bit is only valid from the
address match to the next start bit, stop bit, or ACK bit.
1 = Read
0 = Write
2
bit 1:
bit 0:
UA: Update Address (10-bit I C mode only)
1 = Indicates that the user needs to update the address in the SSPADD register
0 = Address does not need to be updated
BF: Buffer Full Status bit
2
Receive (SPI and I C modes)
1 = Receive complete, SSPBUF is full
0 = Receive not complete, SSPBUF is empty
2
Transmit (I C mode only)
1 = Transmit in progress, SSPBUF is full
0 = Transmit complete, SSPBUF is empty
1997 Microchip Technology Inc.
DS30234D-page 89
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
FIGURE 11-8: SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS 14h)(PIC16C66/67)
R/W-0
R/W-0
R/W-0
R/W-0
CKP
R/W-0
R/W-0
R/W-0
R/W-0
WCOL SSPOV SSPEN
bit7
SSPM3 SSPM2 SSPM1 SSPM0
bit0
R = Readable bit
W = Writable bit
U = Unimplemented bit,
read as ‘0’
- n =Value at POR reset
bit 7:
WCOL: Write Collision Detect bit
1 = The SSPBUF register is written while it is still transmitting the previous word
(must be cleared in software)
0 = No collision
bit 6:
SSPOV: Receive Overflow Indicator bit
In SPI mode
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of over-
flow, the data in SSPSR is lost. Overflow can only occur in slave mode.The user must read the SSPBUF,
even if only transmitting data, to avoid setting overflow. In master mode the overflow bit is not set since
each new reception (and transmission) is initiated by writing to the SSPBUF register.
0 = No overflow
2
In I C mode
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don’t
care" in transmit mode. SSPOV must be cleared in software in either mode.
0 = No overflow
bit 5:
SSPEN: Synchronous Serial Port Enable bit
In SPI mode
1 = Enables serial port and configures SCK, SDO, and SDI as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
2
In I C mode
1 = Enables the serial port and configures the SDA and SCL pins as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
In both modes, when enabled, these pins must be properly configured as input or output.
bit 4:
CKP: Clock Polarity Select bit
In SPI mode
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
2
In I C mode
SCK release control
1 = Enable clock
0 = Holds clock low (clock stretch) (Used to ensure data setup time)
bit 3-0: SSPM3:SSPM0: Synchronous Serial Port Mode Select bits
0000= SPI master mode, clock = FOSC/4
0001= SPI master mode, clock = FOSC/16
0010= SPI master mode, clock = FOSC/64
0011= SPI master mode, clock = TMR2 output/2
0100= SPI slave mode, clock = SCK pin. SS pin control enabled.
0101= SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin
2
0110= I C slave mode, 7-bit address
2
0111= I C slave mode, 10-bit address
2
1011= I C firmware controlled master mode (slave idle)
2
1110= I C slave mode, 7-bit address with start and stop bit interrupts enabled
2
1111= I C slave mode, 10-bit address with start and stop bit interrupts enabled
DS30234D-page 90
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
11.3.1 SSP MODULE IN SPI MODE FOR
PIC16C66/67
EXAMPLE 11-2: LOADING THE SSPBUF
(SSPSR) REGISTER
(PIC16C66/67)
The SPI mode allows 8-bits of data to be synchro-
nously transmitted and received simultaneously. To
accomplish communication, typically three pins are
used:
BCF
BSF
STATUS, RP1
STATUS, RP0
;Specify Bank 1
;
LOOP BTFSS SSPSTAT, BF
;Has data been
;received
• Serial Data Out (SDO) RC5/SDO
• Serial Data In (SDI) RC4/SDI/SDA
• Serial Clock (SCK) RC3/SCK/SCL
;(transmit
;complete)?
;No
GOTO LOOP
BCF
STATUS, RP0
;Specify Bank 0
;W reg = contents
; of SSPBUF
;Save in user RAM
Additionally a fourth pin may be used when in a slave
mode of operation:
MOVF SSPBUF, W
MOVWF RXDATA
• Slave Select (SS) RA5/SS
MOVF TXDATA, W
;W reg = contents
; of TXDATA
;New data to xmit
When initializing the SPI, several options need to be
specified.This is done by programming the appropriate
control bits in the SSPCON register (SSPCON<5:0>)
and SSPSTAT<7:6>. These control bits allow the fol-
lowing to be specified:
MOVWF SSPBUF
The block diagram of the SSP module, when in SPI
mode (Figure 11-9), shows that the SSPSR is not
directly readable or writable, and can only be accessed
from addressing the SSPBUF register. Additionally, the
SSP status register (SSPSTAT) indicates the various
status conditions.
• Master Mode (SCK is the clock output)
• Slave Mode (SCK is the clock input)
• Clock Polarity (Idle state of SCK)
• Clock edge (output data on rising/falling edge of
SCK)
FIGURE 11-9: SSP BLOCK DIAGRAM
(SPI MODE)(PIC16C66/67)
• Clock Rate (Master mode only)
• Slave Select Mode (Slave mode only)
Internal
data bus
The SSP consists of a transmit/receive Shift Register
(SSPSR) and a buffer register (SSPBUF). The SSPSR
shifts the data in and out of the device, MSb first. The
SSPBUF holds the data that was written to the SSPSR
until the received data is ready. Once the 8-bits of data
have been received, that byte is moved to the SSPBUF
register. Then the buffer full detect bit BF
(SSPSTAT<0>) and interrupt flag bit SSPIF (PIR1<3>)
are set. This double buffering of the received data
(SSPBUF) allows the next byte to start reception before
reading the data that was just received. Any write to the
SSPBUF register during transmission/reception of data
will be ignored, and the write collision detect bit WCOL
(SSPCON<7>) will be set. User software must clear the
WCOL bit so that it can be determined if the following
write(s) to the SSPBUF register completed success-
fully. When the application software is expecting to
receive valid data, the SSPBUF should be read before
the next byte of data to transfer is written to the
SSPBUF. Buffer full bit BF (SSPSTAT<0>) indicates
when SSPBUF has been loaded with the received data
(transmission is complete). When the SSPBUF is read,
bit BF is cleared. This data may be irrelevant if the SPI
is only a transmitter. Generally the SSP Interrupt is
used to determine when the transmission/reception
has completed.The SSPBUF must be read and/or writ-
ten. If the interrupt method is not going to be used, then
software polling can be done to ensure that a write col-
lision does not occur. Example 11-2 shows the loading
of the SSPBUF (SSPSR) for data transmission. The
shaded instruction is only required if the received data
is meaningful.
Read
Write
SSPBUF reg
SSPSR reg
shift
clock
RC4/SDI/SDA
RC5/SDO
bit0
Control
Enable
SS
RA5/SS
Edge
Select
2
Clock Select
SSPM3:SSPM0
4
TMR2 output
2
Edge
Select
TCY
Prescaler
4, 16, 64
RC3/SCK/
SCL
TRISC<3>
1997 Microchip Technology Inc.
DS30234D-page 91
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
To enable the serial port, SSP Enable bit, SSPEN
(SSPCON<5>) must be set.To reset or reconfigure SPI
mode, clear bit SSPEN, re-initialize the SSPCON reg-
ister, and then set bit SSPEN. This configures the SDI,
SDO, SCK, and SS pins as serial port pins. For the pins
to behave as the serial port function, they must have
their data direction bits (in the TRISC register) appro-
priately programmed. That is:
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 2) is to broadcast data by
the firmware protocol.
In master mode the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SCK output could be disabled
(programmed as an input). The SSPSR register will
continue to shift in the signal present on the SDI pin at
the programmed clock rate. As each byte is received, it
will be loaded into the SSPBUF register as if a normal
received byte (interrupts and status bits appropriately
set). This could be useful in receiver applications as a
“line activity monitor” mode.
• SDI must have TRISC<4> set
• SDO must have TRISC<5> cleared
• SCK (Master mode) must have TRISC<3>
cleared
• SCK (Slave mode) must have TRISC<3> set
• SS must have TRISA<5> set
In slave mode, the data is transmitted and received as
the external clock pulses appear on SCK. When the
last bit is latched the interrupt flag bit SSPIF (PIR1<3>)
is set.
Any serial port function that is not desired may be over-
ridden by programming the corresponding data direc-
tion (TRIS) register to the opposite value. An example
would be in master mode where you are only sending
data (to a display driver), then both SDI and SS could
be used as general purpose outputs by clearing their
corresponding TRIS register bits.
The clock polarity is selected by appropriately program-
ming bit CKP (SSPCON<4>). This then would give
waveforms for SPI communication as shown in
Figure 11-11, Figure 11-12, and Figure 11-13 where
the MSB is transmitted first. In master mode, the SPI
clock rate (bit rate) is user programmable to be one of
the following:
Figure 11-10 shows a typical connection between two
microcontrollers. The master controller (Processor 1)
initiates the data transfer by sending the SCK signal.
Data is shifted out of both shift registers on their pro-
grammed clock edge, and latched on the opposite edge
of the clock. Both processors should be programmed to
same Clock Polarity (CKP), then both controllers would
send and receive data at the same time. Whether the
data is meaningful (or dummy data) depends on the
application firmware. This leads to three scenarios for
data transmission:
• FOSC/4 (or TCY)
• FOSC/16 (or 4 • TCY)
• FOSC/64 (or 16 • TCY)
• Timer2 output/2
This allows a maximum bit clock frequency (at 20 MHz)
of 5 MHz. When in slave mode the external clock must
meet the minimum high and low times.
• Master sends data — Slave sends dummy data
• Master sends data — Slave sends data
In sleep mode, the slave can transmit and receive data
and wake the device from sleep.
• Master sends dummy data — Slave sends data
FIGURE 11-10: SPI MASTER/SLAVE CONNECTION (PIC16C66/67)
SPI Master SSPM3:SSPM0 = 00xxb
SPI Slave SSPM3:SSPM0 = 010xb
SDO
SDI
Serial Input Buffer
(SSPBUF)
Serial Input Buffer
(SSPBUF)
SDI
SDO
SCK
Shift Register
(SSPSR)
Shift Register
(SSPSR)
LSb
MSb
MSb
LSb
Serial Clock
SCK
PROCESSOR 1
PROCESSOR 2
DS30234D-page 92
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
The SS pin allows a synchronous slave mode. The
SPI must be in slave mode (SSPCON<3:0> = 04h)
and the TRISA<5> bit must be set for the synchro-
nous slave mode to be enabled. When the SS pin is
low, transmission and reception are enabled and the
SDO pin is driven. When the SS pin goes high, the
SDO pin is no longer driven, even if in the middle of
a transmitted byte, and becomes a floating output. If
the SS pin is taken low without resetting SPI mode,
the transmission will continue from the point at
which it was taken high. External pull-up/ pull-down
resistors may be desirable, depending on the applica-
tion.
Note: When the SPI is in Slave Mode with SS pin
control enabled, (SSPCON<3:0> = 0100)
the SPI module will reset if the SSpin is set
to VDD.
Note: If the SPI is used in Slave Mode with
CKE = '1', then the SS pin control must be
enabled.
To emulate two-wire communication, the SDO pin can
be connected to the SDI pin. When the SPI needs to
operate as a receiver the SDO pin can be configured as
an input. This disables transmissions from the SDO.
The SDI can always be left as an input (SDI function)
since it cannot create a bus conflict.
FIGURE 11-11: SPI MODE TIMING, MASTER MODE (PIC16C66/67)
SCK (CKP = 0,
CKE = 0)
SCK (CKP = 0,
CKE = 1)
SCK (CKP = 1,
CKE = 0)
SCK (CKP = 1,
CKE = 1)
bit2
bit7
bit6
bit5
bit3
bit1
bit0
bit4
SDO
SDI (SMP = 0)
bit7
bit0
SDI (SMP = 1)
SSPIF
bit7
bit0
FIGURE 11-12: SPI MODE TIMING (SLAVE MODE WITH CKE = 0) (PIC16C66/67)
SS (optional)
SCK (CKP = 0)
SCK (CKP = 1)
bit2
bit7
bit6
bit5
bit3
bit1
bit0
bit4
SDO
SDI (SMP = 0)
bit7
bit0
SSPIF
1997 Microchip Technology Inc.
DS30234D-page 93
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
FIGURE 11-13: SPI MODE TIMING (SLAVE MODE WITH CKE = 1) (PIC16C66/67)
SS
(not optional)
SCK (CKP = 0)
SCK (CKP = 1)
bit2
SDO
bit7
bit6
bit5
bit3
bit1
bit0
bit4
SDI (SMP = 0)
SSPIF
bit7
bit0
TABLE 11-2: REGISTERS ASSOCIATED WITH SPI OPERATION (PIC16C66/67)
Value on
Power-on
Reset
Value on all
other resets
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0Bh,8Bh,
INTCON
GIE
PEIE
T0IE
INTE
RBIE
T0IF
INTF
RBIF 0000 000x 0000 000u
10Bh,18Bh
(1)
(2)
(2)
PIR1
PIE1
PSPIF
PSPIE
RCIF
RCIE
TXIF
TXIE
SSPIF CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
0Ch
8Ch
13h
14h
85h
87h
94h
(1)
SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register
SSPCON WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 0000 0000 0000 0000
PORTA Data Direction register
PORTC Data Direction register
SMP CKE D/A
xxxx xxxx uuuu uuuu
TRISA
—
—
--11 1111 --11 1111
1111 1111 1111 1111
0000 0000 0000 0000
TRISC
SSPSTAT
P
S
R/W
UA
BF
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0'.
Shaded cells are not used by SSP module in SPI mode.
Note 1: PSPIF and PSPIE are reserved on the PIC16C66, always maintain these bits clear.
2: PIR1<6> and PIE1<6> are reserved, always maintain these bits clear.
DS30234D-page 94
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
2
In both cases the master generates the clock signal.
11.4
I C™ Overview
The output stages of the clock (SCL) and data (SDA)
lines must have an open-drain or open-collector in
order to perform the wired-AND function of the bus.
External pull-up resistors are used to ensure a high
level when no device is pulling the line down. The num-
This section provides an overview of the Inter-Inte-
2
grated Circuit (I C) bus, with Section 11.5 discussing
2
the operation of the SSP module in I C mode.
2
The I C bus is a two-wire serial interface developed by
®
2
the Philips Corporation. The original specification, or
ber of devices that may be attached to the I C bus is
standard mode, was for data transfers of up to 100
Kbps. The enhanced specification (fast mode) is also
supported. This device will communicate with both
standard and fast mode devices if attached to the same
bus. The clock will determine the data rate.
limited only by the maximum bus loading specification
of 400 pF.
11.4.1 INITIATING AND TERMINATING DATA
TRANSFER
2
The I C interface employs a comprehensive protocol to
During times of no data transfer (idle time), both the
clock line (SCL) and the data line (SDA) are pulled high
through the external pull-up resistors. The START and
STOP conditions determine the start and stop of data
transmission.The START condition is defined as a high
to low transition of the SDA when the SCL is high. The
STOP condition is defined as a low to high transition of
the SDA when the SCL is high. Figure 11-14 shows the
START and STOP conditions. The master generates
these conditions for starting and terminating data trans-
fer. Due to the definition of the START and STOP con-
ditions, when data is being transmitted, the SDA line
can only change state when the SCL line is low.
ensure reliable transmission and reception of data.
When transmitting data, one device is the “master”
which initiates transfer on the bus and generates the
clock signals to permit that transfer, while the other
device(s) acts as the “slave.” All portions of the slave
protocol are implemented in the SSP module’s hard-
ware, except general call support, while portions of the
master protocol need to be addressed in the
PIC16CXX software. Table 11-3 defines some of the
I C bus terminology. For additional information on the
I C interface specification, refer to the Philips docu-
ment “The I C bus and how to use it.”#939839340011,
which can be obtained from the Philips Corporation.
2
2
2
2
In the I C interface protocol each device has an
FIGURE 11-14: START AND STOP
CONDITIONS
address. When a master wishes to initiate a data trans-
fer, it first transmits the address of the device that it
wishes to “talk” to. All devices “listen” to see if this is
their address. Within this address, a bit specifies if the
master wishes to read-from/write-to the slave device.
The master and slave are always in opposite modes
(transmitter/receiver) of operation during a data trans-
fer.That is they can be thought of as operating in either
of these two relations:
SDA
S
SCL
P
Change
of Data
Allowed
Change
of Data
Allowed
Start
Condition
Stop
Condition
• Master-transmitter and Slave-receiver
• Slave-transmitter and Master-receiver
2
TABLE 11-3: I C BUS TERMINOLOGY
Term
Description
Transmitter
Receiver
Master
The device that sends the data to the bus.
The device that receives the data from the bus.
The device which initiates the transfer, generates the clock and terminates the transfer.
The device addressed by a master.
Slave
Multi-master
More than one master device in a system. These masters can attempt to control the bus at the
same time without corrupting the message.
Arbitration
Procedure that ensures that only one of the master devices will control the bus. This ensure that
the transfer data does not get corrupted.
Synchronization
Procedure where the clock signals of two or more devices are synchronized.
1997 Microchip Technology Inc.
DS30234D-page 95
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
2
11.4.2 ADDRESSING I C DEVICES
FIGURE 11-17: SLAVE-RECEIVER
ACKNOWLEDGE
There are two address formats. The simplest is the
7-bit address format with a R/W bit (Figure 11-15). The
more complex is the 10-bit address with a R/W bit
(Figure 11-16). For 10-bit address format, two bytes
must be transmitted with the first five bits specifying this
to be a 10-bit address.
Data
Output by
Transmitter
Data
Output by
Receiver
not acknowledge
acknowledge
SCL from
Master
9
8
2
1
FIGURE 11-15: 7-BIT ADDRESS FORMAT
S
MSb
LSb
Clock Pulse for
Acknowledgment
Start
Condition
R/W ACK
S
slave address
Sent by
Slave
If the master is receiving the data (master-receiver), it
generates an acknowledge signal for each received
byte of data, except for the last byte. To signal the end
of data to the slave-transmitter, the master does not
generate an acknowledge (not acknowledge). The
slave then releases the SDA line so the master can
generate the STOP condition. The master can also
generate the STOP condition during the acknowledge
pulse for valid termination of data transfer.
S
R/W
ACK
Start Condition
Read/Write pulse
Acknowledge
2
FIGURE 11-16: I C 10-BIT ADDRESS FORMAT
S
1 1 1 1 0 A9 A8 R/W ACK A7 A6 A5 A4 A3 A2 A1 A0 ACK
sent by slave
If the slave needs to delay the transmission of the next
byte, holding the SCL line low will force the master into
a wait state. Data transfer continues when the slave
releases the SCL line.This allows the slave to move the
received data or fetch the data it needs to transfer
before allowing the clock to start. This wait state tech-
nique can also be implemented at the bit level,
Figure 11-18.The slave will inherently stretch the clock,
when it is a transmitter, but will not when it is a receiver.
The slave will have to clear the SSPCON<4> bit to
enable clock stretching when it is a receiver.
= 0 for write
S
- Start Condition
R/W - Read/Write Pulse
ACK - Acknowledge
11.4.3 TRANSFER ACKNOWLEDGE
All data must be transmitted per byte, with no limit to the
number of bytes transmitted per data transfer. After
each byte, the slave-receiver generates an acknowl-
edge bit (ACK) (Figure 11-17). When a slave-receiver
doesn’t acknowledge the slave address or received
data, the master must abort the transfer. The slave
must leave SDA high so that the master can generate
the STOP condition (Figure 11-14).
FIGURE 11-18: DATA TRANSFER WAIT STATE
SDA
MSB
acknowledgment
signal from receiver
acknowledgment
signal from receiver
byte complete
interrupt with receiver
clock line held low while
interrupts are serviced
SCL
S
1
2
7
8
9
1
2
3 • 8
9
P
Start
Condition
Stop
Condition
Address
R/W ACK Wait
State
Data
ACK
DS30234D-page 96
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
Figure 11-19 and Figure 11-20 show Master-transmit-
ter and Master-receiver data transfer sequences.
SCL is high), but occurs after a data transfer acknowl-
edge pulse (not the bus-free state). This allows a mas-
ter to send “commands” to the slave and then receive
the requested information or to address a different
slave device. This sequence is shown in Figure 11-21.
When a master does not wish to relinquish the bus (by
generating a STOP condition), a repeated START con-
dition (Sr) must be generated. This condition is identi-
cal to the start condition (SDA goes high-to-low while
FIGURE 11-19: MASTER-TRANSMITTER SEQUENCE
For 7-bit address:
For 10-bit address:
S Slave AddressR/W A1 Slave Address A2
S Slave Address R/W A Data A Data A/A P
First 7 bits
Second byte
'0' (write)
data transferred
(n bytes - acknowledge)
(write)
A master transmitter addresses a slave receiver with a
7-bit address. The transfer direction is not changed.
Data A
Data A/A P
A = acknowledge (SDA low)
A = not acknowledge (SDA high)
From master to slave
S = Start Condition
A master transmitter addresses a slave receiver
with a 10-bit address.
From slave to master
P = Stop Condition
FIGURE 11-20: MASTER-RECEIVER SEQUENCE
For 10-bit address:
S Slave AddressR/W A1 Slave Address A2
First 7 bits Second byte
(write)
For 7-bit address:
S Slave Address R/W A Data A Data A
P
'1' (read) data transferred
(n bytes - acknowledge)
A master reads a slave immediately after the first byte.
SrSlave AddressR/W A3 Data A Data A P
First 7 bits
A = acknowledge (SDA low)
A = not acknowledge (SDA high)
From master to slave
(read)
S = Start Condition
A master transmitter addresses a slave receiver
with a 10-bit address.
From slave to master
P = Stop Condition
FIGURE 11-21: COMBINED FORMAT
(read or write)
(n bytes + acknowledge)
S Slave Address R/W A Data A/A Sr Slave Address R/W A Data A/A P
(write)
Direction of transfer
may change at this point
(read)
Sr = repeated
Start Condition
Transfer direction of data and acknowledgment bits depends on R/Wbits.
Combined format:
SrSlave Address R/W A Slave Address A Data A
First 7 bits Second byte
Data A/A Sr Slave Address R/W A Data A
First 7 bits
Data A P
(read)
(write)
Combined format - A master addresses a slave with a 10-bit address, then transmits
data to this slave and reads data from this slave.
A = acknowledge (SDA low)
A = not acknowledge (SDA high)
From master to slave
S = Start Condition
From slave to master
P = Stop Condition
1997 Microchip Technology Inc.
DS30234D-page 97
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
11.4.4 MULTI-MASTER
11.2.4.2 Clock Synchronization
Clock synchronization occurs after the devices have
started arbitration. This is performed using a wired-
AND connection to the SCL line. A high to low transition
on the SCL line causes the concerned devices to start
counting off their low period. Once a device clock has
gone low, it will hold the SCL line low until its SCL high
state is reached. The low to high transition of this clock
may not change the state of the SCL line, if another
device clock is still within its low period.The SCL line is
held low by the device with the longest low period.
Devices with shorter low periods enter a high wait-
state, until the SCL line comes high.When the SCL line
comes high, all devices start counting off their high
periods. The first device to complete its high period will
pull the SCL line low. The SCL line high time is deter-
mined by the device with the shortest high period,
Figure 11-23.
2
The I C protocol allows a system to have more than
one master. This is called multi-master. When two or
more masters try to transfer data at the same time, arbi-
tration and synchronization occur.
11.4.4.1 ARBITRATION
Arbitration takes place on the SDA line, while the SCL
line is high. The master which transmits a high when
the other master transmits a low loses arbitration
(Figure 11-22), and turns off its data output stage. A
master which lost arbitration can generate clock pulses
until the end of the data byte where it lost arbitration.
When the master devices are addressing the same
device, arbitration continues into the data.
FIGURE 11-22: MULTI-MASTER
ARBITRATION
(TWO MASTERS)
FIGURE 11-23: CLOCK SYNCHRONIZATION
transmitter 1 loses arbitration
DATA 1 SDA
start counting
HIGH period
wait
state
DATA 1
DATA 2
SDA
CLK
1
counter
reset
CLK
2
SCL
SCL
Masters that also incorporate the slave function, and
have lost arbitration must immediately switch over to
slave-receiver mode. This is because the winning mas-
ter-transmitter may be addressing it.
Arbitration is not allowed between:
• A repeated START condition
• A STOP condition and a data bit
• A repeated START condition and a STOP condi-
tion
Care needs to be taken to ensure that these conditions
do not occur.
DS30234D-page 98
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
2
2
The SSPCON register allows control of the I C opera-
tion. Four mode selection bits (SSPCON<3:0>) allow
11.5
SSP I C Operation
2
The SSP module in I C mode fully implements all slave
functions, except general call support, and provides
interrupts on start and stop bits in hardware to facilitate
firmware implementations of the master functions. The
SSP module implements the standard mode specifica-
tions as well as 7-bit and 10-bit addressing. Two pins
are used for data transfer. These are the RC3/SCK/
SCL pin, which is the clock (SCL), and the RC4/SDI/
SDA pin, which is the data (SDA). The user must con-
figure these pins as inputs or outputs through the
TRISC<4:3> bits. The SSP module functions are
enabled by setting SSP Enable bit SSPEN (SSP-
CON<5>).
2
one of the following I C modes to be selected:
2
• I C Slave mode (7-bit address)
2
• I C Slave mode (10-bit address)
2
• I C Slave mode (7-bit address), with start and
stop bit interrupts enabled
2
• I C Slave mode (10-bit address), with start and
stop bit interrupts enabled
2
• I C Firmware controlled Master Mode, slave is
idle
2
Selection of any I C mode, with the SSPEN bit set,
forces the SCL and SDA pins to be open drain, pro-
vided these pins are programmed to inputs by setting
the appropriate TRISC bits.
FIGURE 11-24: SSP BLOCK DIAGRAM
2
(I C MODE)
The SSPSTAT register gives the status of the data
transfer. This information includes detection of a
START or STOP bit, specifies if the received byte was
data or address if the next byte is the completion of 10-
bit address, and if this will be a read or write data trans-
fer. The SSPSTAT register is read only.
Internal
data bus
Read
Write
The SSPBUF is the register to which transfer data is
written to or read from. The SSPSR register shifts the
data in or out of the device. In receive operations, the
SSPBUF and SSPSR create a doubled buffered
receiver. This allows reception of the next byte to begin
before reading the last byte of received data. When the
complete byte is received, it is transferred to the
SSPBUF register and flag bit SSPIF is set. If another
complete byte is received before the SSPBUF register
is read, a receiver overflow has occurred and bit
SSPOV (SSPCON<6>) is set and the byte in the
SSPSR is lost.
SSPBUF reg
SSPSR reg
RC3/SCK/SCL
shift
clock
RC4/
SDI/
SDA
MSb
LSb
Addr Match
Match detect
SSPADD reg
The SSPADD register holds the slave address. In 10-bit
mode, the user first needs to write the high byte of the
address (1111 0 A9 A8 0). Following the high byte
address match, the low byte of the address needs to be
loaded (A7:A0).
Set, Reset
S, P bits
Start and
Stop bit detect
(SSPSTAT reg)
2
The SSP module has five registers for I C operation.
These are the:
• SSP Control Register (SSPCON)
• SSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer (SSPBUF)
• SSP Shift Register (SSPSR) - Not directly acces-
sible
• SSP Address Register (SSPADD)
1997 Microchip Technology Inc.
DS30234D-page 99
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
11.5.1 SLAVE MODE
address is compared on the falling edge of the eighth
clock (SCL) pulse. If the addresses match, and the BF
and SSPOV bits are clear, the following events occur:
In slave mode, the SCL and SDA pins must be config-
ured as inputs (TRISC<4:3> set). The SSP module will
override the input state with the output data when
required (slave-transmitter).
a) The SSPSR register value is loaded into the
SSPBUF register.
b) The buffer full bit, BF is set.
c) An ACK pulse is generated.
When an address is matched or the data transfer after
an address match is received, the hardware automati-
cally will generate the acknowledge (ACK) pulse, and
then load the SSPBUF register with the received value
currently in the SSPSR register.
d) SSP interrupt flag bit, SSPIF (PIR1<3>) is set
(interrupt is generated if enabled) - on the falling
edge of the ninth SCL pulse.
In 10-bit address mode, two address bytes need to be
received by the slave (Figure 11-16).The five Most Sig-
nificant bits (MSbs) of the first address byte specify if
this is a 10-bit address. Bit R/W (SSPSTAT<2>) must
specify a write so the slave device will receive the sec-
ond address byte. For a 10-bit address the first byte
would equal ‘1111 0 A9 A8 0’, where A9 and A8 are
the two MSbs of the address. The sequence of events
for 10-bit address is as follows, with steps 7- 9 for slave-
transmitter:
There are certain conditions that will cause the SSP
module not to give this ACK pulse. These are if either
(or both):
a) The buffer full bit BF (SSPSTAT<0>) was set
before the transfer was received.
b) The overflow bit SSPOV (SSPCON<6>) was set
before the transfer was received.
In this case, the SSPSR register value is not loaded
into the SSPBUF, but bit SSPIF (PIR1<3>) is set.
Table 11-4 shows what happens when a data transfer
byte is received, given the status of bits BF and SSPOV.
The shaded cells show the condition where user soft-
ware did not properly clear the overflow condition. Flag
bit BF is cleared by reading the SSPBUF register while
bit SSPOV is cleared through software.
1. Receive first (high) byte of Address (bits SSPIF,
BF, and bit UA (SSPSTAT<1>) are set).
2. Update the SSPADD register with second (low)
byte of Address (clears bit UA and releases the
SCL line).
3. Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
The SCL clock input must have a minimum high and
low for proper operation. The high and low times of the
4. Receive second (low) byte of Address (bits
SSPIF, BF, and UA are set).
2
I C specification as well as the requirement of the SSP
module is shown in timing parameter #100 and param-
eter #101.
5. Update the SSPADD register with the first (high)
byte of Address, if match releases SCL line, this
will clear bit UA.
11.5.1.1 ADDRESSING
6. Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Once the SSP module has been enabled, it waits for a
START condition to occur. Following the START condi-
tion, the 8-bits are shifted into the SSPSR register. All
incoming bits are sampled with the rising edge of the
clock (SCL) line. The value of register SSPSR<7:1> is
compared to the value of the SSPADD register. The
7. Receive repeated START condition.
8. Receive first (high) byte of Address (bits SSPIF
and BF are set).
9. Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
TABLE 11-4: DATA TRANSFER RECEIVED BYTE ACTIONS
Status Bits as Data
Transfer is Received
Set bit SSPIF
(SSP Interrupt occurs
if enabled)
Generate ACK
Pulse
BF
SSPOV
SSPSR → SSPBUF
0
1
1
0
0
0
1
1
Yes
No
No
No
Yes
No
No
No
Yes
Yes
Yes
Yes
DS30234D-page 100
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
11.5.1.2 RECEPTION
An SSP interrupt is generated for each data transfer
byte. Flag bit SSPIF (PIR1<3>) must be cleared in soft-
ware. The SSPSTAT register is used to determine the
status of the byte.
When the R/W bit of the address byte is clear and an
address match occurs, the R/Wbit of the SSPSTAT reg-
ister is cleared.The received address is loaded into the
SSPBUF register.
When the address byte overflow condition exists, then
no acknowledge (ACK) pulse is given. An overflow con-
dition is defined as either bit BF (SSPSTAT<0>) is set
or bit SSPOV (SSPCON<6>) is set.
2
FIGURE 11-25: I C WAVEFORMS FOR RECEPTION (7-BIT ADDRESS)
Receiving Address
A7 A6 A5 A4
R/W=0
Receiving Data
Receiving Data
ACK
9
ACK
9
ACK
9
SDA
SCL
A3 A2 A1
D5
D2
D0
8
D5
D2
D0
8
D7 D6
D4 D3
D7 D6
D4 D3
D1
7
D1
7
3
7
1
2
4
5
4
3
6
5
6
1
2
3
6
1
2
4
8
5
P
S
SSPIF (PIR1<3>)
Cleared in software
Bus Master
terminates
transfer
BF (SSPSTAT<0>)
SSPBUF register is read
SSPOV (SSPCON<6>)
Bit SSPOV is set because the SSPBUF register is still full.
ACK is not sent.
1997 Microchip Technology Inc.
DS30234D-page 101
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
11.5.1.3 TRANSMISSION
An SSP interrupt is generated for each data transfer
byte. Flag bit SSPIF must be cleared in software, and
the SSPSTAT register is used to determine the status
of the byte. Flag bit SSPIF is set on the falling edge of
the ninth clock pulse.
When the R/W bit of the incoming address byte is set
and an address match occurs, the R/W bit of the
SSPSTAT register is set. The received address is
loaded into the SSPBUF register. The ACK pulse will
be sent on the ninth bit, and pin RC3/SCK/SCL is held
low. The transmit data must be loaded into the SSP-
BUF register, which also loads the SSPSR register.
Then pin RC3/SCK/SCL should be enabled by setting
bit CKP (SSPCON<4>). The master must monitor the
SCL pin prior to asserting another clock pulse. The
slave devices may be holding off the master by stretch-
ing the clock. The eight data bits are shifted out on the
falling edge of the SCL input.This ensures that the SDA
signal is valid during the SCL high time (Figure 11-26).
As a slave-transmitter, the ACK pulse from the master-
receiver is latched on the rising edge of the ninth SCL
input pulse. If the SDA line was high (not ACK), then the
data transfer is complete. When the ACK is latched by
the slave, the slave logic is reset (resets SSPSTAT reg-
ister) and the slave then monitors for another occur-
rence of the START bit. If the SDA line was low (ACK),
the transmit data must be loaded into the SSPBUF reg-
ister, which also loads the SSPSR register. Then pin
RC3/SCK/SCL should be enabled by setting bit CKP.
2
FIGURE 11-26: I C WAVEFORMS FOR TRANSMISSION (7-BIT ADDRESS)
Receiving Address
R/W = 1
ACK
Transmitting Data
ACK
9
SDA
SCL
A7 A6 A5 A4 A3 A2 A1
D7 D6 D5 D4 D3 D2 D1 D0
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
S
P
SCL held low
while CPU
responds to SSPIF
Data in
sampled
SSPIF (PIR1<3>)
BF (SSPSTAT<0>)
cleared in software
SSPBUF is written in software
From SSP interrupt
service routine
CKP (SSPCON<4>)
Set bit after writing to SSPBUF
(the SSPBUF must be written-to
before the CKP bit can be set)
DS30234D-page 102
1997 Microchip Technology Inc.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
11.5.2 MASTER MODE
11.5.3 MULTI-MASTER MODE
Master mode of operation is supported in firmware
using interrupt generation on the detection of the
START and STOP conditions. The STOP (P) and
START (S) bits are cleared from a reset or when the
SSP module is disabled.The STOP (P) and START (S)
bits will toggle based on the START and STOP condi-
In multi-master mode, the interrupt generation on the
detection of the START and STOP conditions allows
the determination of when the bus is free. The STOP
(P) and START (S) bits are cleared from a reset or
when the SSP module is disabled. The STOP (P) and
START (S) bits will toggle based on the START and
2
2
tions. Control of the I C bus may be taken when the P
STOP conditions. Control of the I C bus may be taken
bit is set, or the bus is idle and both the S and P bits are
clear.
when bit P (SSPSTAT<4>) is set, or the bus is idle and
both the S and P bits clear. When the bus is busy,
enabling the SSP Interrupt will generate the interrupt
when the STOP condition occurs.
In master mode the SCL and SDA lines are manipu-
lated by clearing the corresponding TRISC<4:3> bit(s).
The output level is always low, irrespective of the
value(s) in PORTC<4:3>. So when transmitting data, a
'1' data bit must have the TRISC<4> bit set (input) and
a '0' data bit must have the TRISC<4> bit cleared (out-
put).The same scenario is true for the SCL line with the
TRISC<3> bit.
In multi-master operation, the SDA line must be moni-
tored to see if the signal level is the expected output
level. This check only needs to be done when a high
level is output. If a high level is expected and a low level
is present, the device needs to release the SDA and
SCL lines (set TRISC<4:3>). There are two stages
where this arbitration can be lost, these are:
The following events will cause SSP Interrupt Flag bit,
SSPIF, to be set (SSP Interrupt if enabled):
• Address Transfer
• Data Transfer
• START condition
• STOP condition
When the slave logic is enabled, the slave continues to
receive. If arbitration was lost during the address trans-
fer stage, communication to the device may be in
progress. If addressed an ACK pulse will be generated.
If arbitration was lost during the data transfer stage, the
device will need to re-transfer the data at a later time.
• Data transfer byte transmitted/received
Master mode of operation can be done with either the
slave mode idle (SSPM3:SSPM0 = 1011) or with the
slave active. When both master and slave modes are
enabled, the software needs to differentiate the
source(s) of the interrupt.
2
TABLE 11-5: REGISTERS ASSOCIATED WITH I C OPERATION
Value on
POR,
BOR
Value on all
other resets
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0000 000x 0000 000u
0Bh, 8Bh, INTCON
10Bh, 18Bh
GIE
PEIE
T0IE
INTE
RBIE
T0IF
INTF
RBIF
(1)
(2)
(2)
PIR1
PIE1
PSPIF
PSPIE
RCIF
RCIE
TXIF
TXIE
SSPIF CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
0Ch
8Ch
13h
93h
14h
94h
87h
(1)
xxxx xxxx uuuu uuuu
0000 0000 0000 0000
0000 0000 0000 0000
0000 0000 0000 0000
SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register
2
SSPADD Synchronous Serial Port (I C mode) Address Register
SSPCON
WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0
(3)
(3)
SSPSTAT SMP
CKE
D/A
P
S
R/W
UA
BF
PORTC Data Direction register
TRISC
1111 1111 1111 1111
Legend: x= unknown, u= unchanged, -= unimplemented locations read as '0'.
Shaded cells are not used by SSP module in SPI mode.
Note 1: PSPIF and PSPIE are reserved on the PIC16C66, always maintain these bits clear.
2: PIR1<6> and PIE1<6> are reserved, always maintain these bits clear.
3: The SMP and CKE bits are implemented on the PIC16C66/67 only. All other PIC16C6X devices have these two bits unim-
plemented, read as '0'.
1997 Microchip Technology Inc.
DS30234D-page 103
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
PIC16C6X
2
FIGURE 11-27: OPERATION OF THE I C MODULE IN IDLE_MODE, RCV_MODE OR XMIT_MODE
IDLE_MODE (7-bit):
if (Addr_match)
{
Set interrupt;
if (R/W = 1)
{
}
Send ACK = 0;
set XMIT_MODE;
else if (R/W = 0) set RCV_MODE;
}
RCV_MODE:
if ((SSPBUF=Full) OR (SSPOV = 1))
{
Set SSPOV;
Do not acknowledge;
}
{
else
transfer SSPSR → SSPBUF;
send ACK = 0;
}
Receive 8-bits in SSPSR;
Set interrupt;
XMIT_MODE:
While ((SSPBUF = Empty) AND (CKP=0)) Hold SCL Low;
Send byte;
Set interrupt;
if ( ACK Received = 1)
{
}
End of transmission;
Go back to IDLE_MODE;
else if ( ACK Received = 0) Go back to XMIT_MODE;
IDLE_MODE (10-Bit):
If (High_byte_addr_match AND (R/W = 0))
{
PRIOR_ADDR_MATCH = FALSE;
Set interrupt;
if ((SSPBUF = Full) OR ((SSPOV = 1))
{
Set SSPOV;
Do not acknowledge;
}
{
else
Set UA = 1;
Send ACK = 0;
While (SSPADD not updated) Hold SCL low;
Clear UA = 0;
Receive Low_addr_byte;
Set interrupt;
Set UA = 1;
If (Low_byte_addr_match)
{
PRIOR_ADDR_MATCH = TRUE;
Send ACK = 0;
while (SSPADD not updated) Hold SCL low;
Clear UA = 0;
Set RCV_MODE;
}
}
}
else if (High_byte_addr_match AND (R/W = 1)
if (PRIOR_ADDR_MATCH)
{
{
send ACK = 0;
set XMIT_MODE;
}
else PRIOR_ADDR_MATCH = FALSE;
}
DS30234D-page 104
1997 Microchip Technology Inc.
PIC16C6X
minals and personal computers, or it can be configured
as a half duplex synchronous system that can commu-
nicate with peripheral devices such as A/D or D/A inte-
grated circuits, Serial EEPROMs etc.
12.0 UNIVERSAL SYNCHRONOUS
ASYNCHRONOUS RECEIVER
TRANSMITTER (USART)
MODULE
The USART can be configured in the following modes:
Applicable Devices
• Asynchronous (full duplex)
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
• Synchronous - Master (half duplex)
• Synchronous - Slave (half duplex)
The Universal Synchronous Asynchronous Receiver
Transmitter (USART) module is one of the two serial
I/O modules. (USART is also known as a Serial Com-
munications Interface or SCI) The USART can be con-
figured as a full duplex asynchronous system that can
communicate with peripheral devices such as CRT ter-
Bit SPEN (RCSTA<7>) and bits TRISC<7:6> have to
be set in order to configure pins RC6/TX/CK and
RC7/RX/DT as the Universal Synchronous Asynchro-
nous Receiver Transmitter.
FIGURE 12-1: TXSTA:TRANSMIT STATUS AND CONTROL REGISTER (ADDRESS 98h)
R/W-0
CSRC
R/W-0
TX9
R/W-0
TXEN
R/W-0
SYNC
U-0
—
R/W-0
BRGH
R-1
R/W-0
TX9D
TRMT
R = Readable bit
W = Writable bit
bit7
bit0
U = Unimplemented bit,
read as ‘0’
- n =Value at POR reset
bit 7:
CSRC: Clock Source Select bit
Asynchronous mode
Don’t care
Synchronous mode
1 = Master mode (Clock generated internally from BRG)
0 = Slave mode (Clock from external source)
bit 6:
TX9: 9-bit Transmit Enable bit
1 = Selects 9-bit transmission
0 = Selects 8-bit transmission
bit 5:
TXEN: Transmit Enable bit
1 = Transmit enabled
0 = Transmit disabled
Note: SREN/CREN overrides TXEN in SYNC mode.
bit 4:
SYNC: USART Mode Select bit
1 = Synchronous mode
0 = Asynchronous mode
bit 3:
bit 2:
Unimplemented: Read as '0'
BRGH: High Baud Rate Select bit
Asynchronous mode
1 = High speed
Note: For the PIC16C63/R63/65/65A/R65 the asynchronous high speed mode (BRGH = 1) may
experience a high rate of receive errors. It is recommended that BRGH = 0. If you desire a
higher baud rate than BRGH = 0 can support, refer to the device errata for additional infor-
mation or use the PIC16C66/67.
0 = Low speed
Synchronous mode
Unused in this mode
bit 1:
bit 0:
TRMT: Transmit Shift Register Status bit
1 = TSR empty
0 = TSR full
TX9D: 9th bit of transmit data. Can be parity bit.
1997 Microchip Technology Inc.
DS30234D-page 105
PIC16C6X
FIGURE 12-2: RCSTA: RECEIVE STATUS AND CONTROL REGISTER (ADDRESS 18h)
R/W-0
SPEN
R/W-0
RX9
R/W-0
SREN
R/W-0
CREN
U-0
—
R-0
R-0
R-x
FERR
OERR
RX9D
R
W
U
= Readable bit
= Writable bit
= Unimplemented
bit, read as ‘0’
bit7
bit0
- n = Value at POR reset
= unknown
x
bit 7:
SPEN: Serial Port Enable bit
(Configures RC7/RX/DT and RC6/TX/CK pins as serial port pins when bits TRISC<7:6> are set)
1 = Serial port enabled
0 = Serial port disabled
bit 6:
RX9: 9-bit Receive Enable bit
1 = Selects 9-bit reception
0 = Selects 8-bit reception
bit 5:
SREN: Single Receive Enable bit
Asynchronous mode
Don’t care
Synchronous mode - master
1 = Enables single receive
0 = Disables single receive
This bit is cleared after reception is complete.
Synchronous mode - slave
Unused in this mode
bit 4:
CREN: Continuous Receive Enable bit
Asynchronous mode
1 = Enables continuous receive
0 = Disables continuous receive
Synchronous mode
1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN)
0 = Disables continuous receive
bit 3:
bit 2:
Unimplemented: Read as '0'
FERR: Framing Error bit
1 = Framing error (Can be updated by reading RCREG register and receive next valid byte)
0 = No framing error
bit 1:
bit 0:
OERR: Overrun Error bit
1 = Overrun error (Can be cleared by clearing bit CREN)
0 = No overrun error
RX9D: 9th bit of received data (Can be parity bit)
DS30234D-page 106
1997 Microchip Technology Inc.
PIC16C6X
12.1
USART Baud Rate Generator (BRG)
EXAMPLE 12-1: CALCULATING BAUD
RATE ERROR
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Desired Baud rate = Fosc / (64 (X + 1))
The BRG supports both the Asynchronous and Syn-
chronous modes of the USART. It is a dedicated 8-bit
baud rate generator. The SPBRG register controls the
period of a free running 8-bit timer. In asynchronous
mode bit BRGH (TXSTA<2>) also controls the baud
rate. In synchronous mode bit BRGH is ignored.
Table 12-1 shows the formula for computation of the
baud rate for different USART modes which only apply
in master mode (internal clock).
9600
X
=
=
16000000 /(64 (X + 1))
25.042 = 25
Calculated Baud Rate=16000000 / (64 (25 + 1))
=
=
9615
Error
(Calculated Baud Rate - Desired Baud Rate)
Desired Baud Rate
=
=
(9615 - 9600) / 9600
0.16%
Given the desired baud rate and Fosc, the nearest inte-
ger value for the SPBRG register can be calculated
using the formula in Table 12-1. From this, the error in
baud rate can be determined.
It may be advantageous to use the high baud rate
(BRGH = 1) even for slower baud clocks. This is
because the FOSC/(16(X + 1)) equation can reduce the
baud rate error in some cases.
Example 12-1 shows the calculation of the baud rate
error for the following conditions:
Note: For the PIC16C63/R63/65/65A/R65 the
FOSC = 16 MHz
Desired Baud Rate = 9600
BRGH = 0
asynchronous
high
speed
mode
(BRGH = 1) may experience a high rate of
receive errors. It is recommended that
BRGH = 0. If you desire a higher baud rate
than BRGH = 0 can support, refer to the
device errata for additional information or
use the PIC16C66/67.
SYNC = 0
Writing a new value to the SPBRG register, causes the
BRG timer to be reset (or cleared), this ensures that the
BRG does not wait for a timer overflow before output-
ting the new baud rate.
TABLE 12-1: BAUD RATE FORMULA
SYNC
BRGH = 0 (Low Speed)
BRGH = 1 (High Speed)
0
1
(Asynchronous) Baud Rate = FOSC/(64(X+1))
(Synchronous) Baud Rate = FOSC/(4(X+1))
Baud Rate = FOSC/(16(X+1))
N/A
X = value in SPBRG (0 to 255)
TABLE 12-2: REGISTERS ASSOCIATED WITH BAUD RATE GENERATOR
Value on
POR,
BOR
Value on
all other
Resets
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
98h
18h
99h
TXSTA
RCSTA
SPBRG
CSRC
SPEN
TX9
RX9
TXEN
SREN
SYNC
CREN
—
—
BRGH
FERR
TRMT
OERR
TX9D 0000 -010 0000 -010
RX9D 0000 -00x 0000 -00x
0000 0000 0000 0000
Baud Rate Generator Register
Legend: x= unknown, -= unimplemented read as '0'. Shaded cells are not used by the BRG.
1997 Microchip Technology Inc.
DS30234D-page 107
PIC16C6X
TABLE 12-3: BAUD RATES FOR SYNCHRONOUS MODE
FOSC = 20 MHz
16 MHz
KBAUD
10 MHz
KBAUD
7.15909 MHz
KBAUD
BAUD
RATE
(K)
SPBRG
value
SPBRG
value
ERROR (decimal)
SPBRG
value
ERROR (decimal)
SPBRG
value
ERROR (decimal)
%
%
%
%
KBAUD
ERROR (decimal)
0.3
1.2
2.4
NA
NA
NA
-
-
-
-
-
-
NA
NA
NA
-
-
-
-
-
-
NA
NA
NA
-
-
-
-
-
-
NA
NA
NA
-
-
-
-
-
-
9.6
NA
-
+1.73
+0.16
+0.16
-1.96
0
-
NA
-
+0.16
+0.16
-0.79
+2.56
0
-
9.766
19.23
75.76
96.15
312.5
500
+1.73
+0.16
-1.36
+0.16
+4.17
0
255
129
32
25
7
4
0
255
9.622
19.24
77.82
94.20
298.3
NA
+0.23
+0.23
+1.32
-1.88
-0.57
-
185
92
22
18
5
-
0
255
19.2
76.8
96
300
500
HIGH
LOW
19.53
76.92
96.15
294.1
500
255
64
51
16
9
19.23
76.92
95.24
307.69
500
207
51
41
12
7
5000
19.53
-
-
0
255
4000
15.625
-
-
0
255
2500
9.766
-
-
1789.8
6.991
-
-
FOSC = 5.0688 MHz
SPBRG
4 MHz
3.579545 MHz
1 MHz
32.768 kHz
BAUD
SPBRG
value
ERROR (decimal)
SPBRG
value KBAUD
ERROR (decimal)
SPBRG
SPBRG
value
RATE KBAUD
(K)
%
value KBAUD
%
KBAUD
%
%
value KBAUD
%
ERROR (decimal)
ERROR (decimal)
ERROR (decimal)
0.3
1.2
2.4
NA
NA
NA
-
-
-
0
-
-
-
NA
NA
NA
-
-
-
-
-
-
NA
NA
NA
9.622
19.04
74.57
99.43
298.3
NA
-
-
-
-
-
-
92
46
11
8
2
-
0
255
NA
1.202
2.404
9.615
19.24
83.34
NA
NA
NA
250
0.9766
-
-
207
103
25
12
2
-
-
-
0
0.303
1.170
NA
NA
NA
NA
NA
NA
NA
+1.14
-2.48
26
6
-
-
-
-
-
-
-
+0.16
+0.16
+0.16
+0.16
-
-
-
-
-
-
-
-
-
9.6
9.6
131
65
15
12
3
-
0
255
9.615
19.231 +0.16
76.923 +0.16
1000
NA
NA
+0.16
103
51
12
9
-
-
+0.23
-0.83
-2.90
+3.57
-0.57
-
19.2
76.8
96
300
500
HIGH
LOW
19.2
79.2
97.48
316.8
NA
0
+3.13
+1.54
+5.60
-
-
-
+8.51
+4.17
-
-
-
-
-
-
-
-
-
1267
4.950
100
3.906
0
255
894.9
3.496
-
-
8.192
0.032
0
255
255
TABLE 12-4: BAUD RATES FOR ASYNCHRONOUS MODE (BRGH = 0)
FOSC = 20 MHz
%
16 MHz
10 MHz
7.15909 MHz
BAUD
RATE
(K)
SPBRG
value
SPBRG
value
SPBRG
value
SPBRG
value
%
%
%
KBAUD ERROR (decimal) KBAUD ERROR (decimal) KBAUD ERROR (decimal) KBAUD ERROR (decimal)
0.3
1.2
2.4
NA
-
-
255
129
32
15
3
2
0
-
0
NA
1.202
2.404
9.615
19.23
83.33
NA
NA
NA
250
0.977
-
-
207
103
25
12
2
-
-
-
0
NA
1.202
2.404
9.766
19.53
78.13
NA
NA
NA
156.3
0.6104
-
-
129
64
15
7
1
-
-
-
NA
1.203
2.380
9.322
18.64
NA
NA
NA
NA
111.9
0.437
-
-
92
46
11
5
-
-
-
-
1.221
2.404
9.469
19.53
78.13
104.2
312.5
NA
+1.73
+0.16
-1.36
+1.73
+1.73
+8.51
+4.17
-
+0.16
+0.16
+0.16
+0.16
+0.16
+0.16
+1.73
+1.73
+0.23
-0.83
-2.90
-2.90
-
-
-
-
-
-
9.6
19.2
76.8
96
300
500
HIGH
LOW
+8.51
+1.73
-
-
-
-
-
-
-
-
-
-
312.5
1.221
-
-
0
255
0
255
255
255
FOSC = 5.0688 MHz
4 MHz
3.579545 MHz
%
1 MHz
32.768 kHz
BAUD
RATE
(K)
SPBRG
value
SPBRG
value
SPBRG
value
SPBRG
value
SPBRG
value
%
%
%
%
KBAUD ERROR (decimal) KBAUD ERROR (decimal) KBAUD ERROR (decimal) KBAUD ERROR (decimal) KBAUD ERROR (decimal)
0.3
1.2
2.4
0.31
1.2
2.4
+3.13
0
0
+3.13
+3.13
+3.13
-
-
-
-
-
255
65
32
7
3
0
-
-
-
0
0.3005 -0.17
207
51
25
-
-
-
-
-
-
0.301
1.190
2.432
9.322
18.64
NA
NA
NA
NA
55.93
0.2185
+0.23
-0.83
+1.32
-2.90
185
46
22
5
2
-
-
-
-
0
0.300
1.202
2.232
NA
NA
NA
NA
NA
NA
15.63
0.0610
+0.16
+0.16
-6.99
51
12
6
-
-
-
-
-
-
0.256 -14.67
1
-
-
-
-
-
-
-
-
1.202
2.404
NA
+1.67
+1.67
NA
NA
-
-
-
-
-
-
-
-
-
-
9.6
9.9
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
NA
19.2
76.8
96
300
500
HIGH
LOW
19.8
79.2
NA
NA
NA
NA
NA
-2.90
NA
-
-
-
-
-
-
NA
NA
NA
NA
NA
NA
NA
79.2
0.3094
62.500
3.906
0
255
0
255
0.512
0.0020
0
255
255
255
DS30234D-page 108
1997 Microchip Technology Inc.
PIC16C6X
TABLE 12-5: BAUD RATES FOR ASYNCHRONOUS MODE (BRGH = 1)
FOSC = 20 MHz
%
16 MHz
10 MHz
7.16 MHz
BAUD
RATE
(K)
SPBRG
value
SPBRG
value
SPBRG
value
SPBRG
value
%
%
%
KBAUD ERROR (decimal) KBAUD ERROR (decimal) KBAUD ERROR (decimal) KBAUD ERROR (decimal)
9.6
9.615
19.230
37.878
56.818
+0.16
+0.16
-1.36
-1.36
-1.36
0
129
64
32
21
10
4
9.615
19.230
38.461
58.823
111.111
250
+0.16
+0.16
+0.16
+2.12
-3.55
0
103
51
25
16
8
9.615
18.939
39.062
56.818
125
+0.16
-1.36
+1.7
-1.36
+8.51
-
64
32
15
10
4
9.520
19.454
37.286
55.930
111.860
NA
-0.83
+1.32
-2.90
-2.90
-2.90
-
46
22
11
7
3
-
19.2
38.4
57.6
115.2 113.636
250
625
250
625
3
-
NA
625
-
0
0
1
NA
-
0
NA
-
-
1250
1250
0
0
NA
-
-
NA
-
-
NA
-
-
FOSC = 5.068 MHz
%
4 MHz
3.579 MHz
1 MHz
32.768 kHz
BAUD
RATE
(K)
SPBRG
value
SPBRG
value
SPBRG
value
SPBRG
value
SPBRG
value
%
%
%
%
KBAUD ERROR (decimal) KBAUD ERROR (decimal) KBAUD ERROR (decimal) KBAUD ERROR (decimal) KBAUD ERROR (decimal)
9.6
19.2
9.6
18.645
0
32
16
NA
1.202
-
-
9.727
18.643 -2.90
+1.32
22
11
8.928
20.833 +8.51
-6.99
6
2
NA
NA
-
-
-
-
-2.94
207
+0.17
+0.13
+0.16
38.4
57.6
115.2
250
625
1250
39.6
52.8
105.6
NA
NA
NA
+3.12
-8.33
-8.33
-
-
-
7
5
2
-
-
-
2.403
9.615
19.231 +0.16
NA
NA
NA
103
25
12
-
-
-
37.286 -2.90
55.930 -2.90
111.860 -2.90
223.721 -10.51
NA
NA
5
3
1
0
-
31.25 -18.61
1
0
-
-
-
NA
NA
NA
NA
NA
NA
-
-
-
-
-
-
-
-
-
-
-
-
62.5
NA
NA
NA
NA
+8.51
-
-
-
-
-
-
-
-
-
-
-
Note: For the PIC16C63/R63/65/65A/R65 the asynchronous high speed mode (BRGH = 1) may experience a
high rate of receive errors. It is recommended that BRGH = 0. If you desire a higher baud rate than BRGH
= 0 can support, refer to the device errata for additional information or use the PIC16C66/67.
1997 Microchip Technology Inc.
DS30234D-page 109
PIC16C6X
12.1.1 SAMPLING
set (i.e., at the high baud rates), the sampling is done
on the 3 clock edges preceding the second rising edge
after the first falling edge of a x4 clock (Figure 12-4 and
Figure 12-5).
The data on the RC7/RX/DT pin is sampled three times
by a majority detect circuit to determine if a high or a
low level is present at the RX pin. If bit BRGH
(TXSTA<2>) is clear (i.e., at the low baud rates), the
sampling is done on the seventh, eighth and ninth fall-
ing edges of a x16 clock (Figure 12-3). If bit BRGH is
FIGURE 12-3: RX PIN SAMPLING SCHEME (BRGH = 0) PIC16C63/R63/65/65A/R65)
Start bit
Bit0
RX
(RC7/RX/DT pin)
Baud CLK for all but start bit
baud CLK
x16 CLK
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
1
2
3
Samples
FIGURE 12-4: RX PIN SAMPLING SCHEME (BRGH = 1) (PIC16C63/R63/65/65A/R65)
RC7/RX/DT pin
bit0
bit1
Start Bit
baud clk
First falling edge after RX pin goes low
Second rising edge
x4 clk
1
2
3
4
1
2
3
4
1
2
Q2, Q4 clk
Samples
Samples
Samples
FIGURE 12-5: RX PIN SAMPLING SCHEME (BRGH = 1) (PIC16C63/R63/65/65A/R65)
RC7/RX/DT pin
Start Bit
bit0
Baud clk for all but start bit
baud clk
First falling edge after RX pin goes low
Second rising edge
x4 clk
1
2
3
4
Q2, Q4 clk
Samples
DS30234D-page 110
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 12-6: RX PIN SAMPLING SCHEME (BRGH = 0 OR = 1) (PIC16C66/67)
Start bit
Bit0
RX
(RC7/RX/DT pin)
Baud CLK for all but start bit
baud CLK
x16 CLK
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
1
2
3
Samples
1997 Microchip Technology Inc.
DS30234D-page 111
PIC16C6X
abled by setting/clearing enable bit TXIE (PIE1<4>).
Flag bit TXIF will be set regardless of the state of
enable bit TXIE and cannot be cleared in software. It
will reset only when new data is loaded into the TXREG
register. While flag bit TXIF indicates the status of the
TXREG register, another bit, TRMT (TXSTA<1>)
shows the status of the TSR register. Status bit TRMT
is a read only bit which is set when the TSR register is
empty. No interrupt logic is tied to this bit, so the user
has to poll this bit in order to determine if the TSR reg-
ister is empty.
12.2
USART Asynchronous Mode
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
In this mode, the USART uses standard nonreturn-to-
zero (NRZ) format (one start bit, eight or nine data bits
and one stop bit). The most common data format is
8-bits. An on-chip dedicated 8-bit baud rate generator
can be used to derive standard baud rate frequencies
from the oscillator. The USART transmits and receives
the LSb first.The USART’s transmitter and receiver are
functionally independent but use the same data format
and baud rate. The baud rate generator produces a
clock either x16 or x64 of the bit shift rate, depending
on bit BRGH (TXSTA<2>). Parity is not supported by
the hardware, but can be implemented in software (and
stored as the ninth data bit). Asynchronous mode is
stopped during SLEEP.
Note 1: The TSR register is not mapped in data
memory so it is not available to the user.
Note 2: Flag bit TXIF is set when enable bit TXEN
is set.
Transmission is enabled by setting enable bit TXEN
(TXSTA<5>). The actual transmission will not occur
until the TXREG register has been loaded with data
and the baud rate generator (BRG) has produced a
shift clock (Figure 12-7). The transmission can also be
started by first loading the TXREG register and then
setting enable bit TXEN. Normally when transmission
is first started, the TSR register is empty, so a transfer
to the TXREG register will result in an immediate trans-
fer to TSR register resulting in an empty TXREG regis-
ter. A back-to-back transfer is thus possible (Figure 12-
9). Clearing enable bit TXEN during a transmission will
cause the transmission to be aborted and will reset the
transmitter. As a result the RC6/TX/CK pin will revert to
hi-impedance.
Asynchronous mode is selected by clearing bit SYNC
(TXSTA<4>).
The USART Asynchronous module consists of the fol-
lowing important elements:
• Baud Rate Generator
• Sampling Circuit
• Asynchronous Transmitter
• Asynchronous Receiver
12.2.1 USART ASYNCHRONOUS TRANSMITTER
The USART transmitter block diagram is shown in
Figure 12-7. The heart of the transmitter is the transmit
(serial) shift register (TSR).The shift register obtains its
data from the read/write transmit buffer, TXREG. The
TXREG register is loaded with data in software. The
TSR register is not loaded until the STOP bit has been
transmitted from the previous load. As soon as the
STOP bit is transmitted, the TSR is loaded with new
data from the TXREG (if available). Once the TXREG
register transfers the data to the TSR register (occurs
in one TCY) the TXREG register is empty and flag bit
TXIF (PIR1<4>) is set. This interrupt is enabled/dis-
In order to select 9-bit transmission, transmit bit TX9
(TXSTA<6>) should be set and the ninth bit should be
written to bit TX9D (TXSTA<0>). The ninth bit must be
written before writing the 8-bit data to the TXREG reg-
ister. This is because a data write to the TXREG regis-
ter can result in an immediate transfer of the data to the
TSR register (if the TSR is empty). In such a case, an
incorrect ninth data bit maybe loaded in the TSR regis-
ter.
FIGURE 12-7: USART TRANSMIT BLOCK DIAGRAM
Data Bus
TXIF
TXREG register
8
TXIE
MSb
(8)
LSb
Pin Buffer
and Control
0
•
• •
TSR register
RC6/TX/CK pin
Interrupt
TXEN
Baud Rate CLK
TRMT
SPEN
SPBRG
Baud Rate Generator
TX9
TX9D
DS30234D-page 112
1997 Microchip Technology Inc.
PIC16C6X
Steps to follow when setting up an Asynchronous
Transmission:
5. Enable the transmission by setting bit TXEN,
which will also set bit TXIF.
6. If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
1. Initialize the SPBRG register for the appropriate
baud rate. If a high speed baud rate is desired,
then set bit BRGH. (Section 12.1).
7. Load data to the TXREG register (starts trans-
mission).
2. Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
3. If interrupts are desired, then set enable bit
TXIE.
4. If 9-bit transmission is desired, then set transmit
bit TX9.
FIGURE 12-8: ASYNCHRONOUS MASTER TRANSMISSION
Write to TXREG reg
Word 1
BRG output
(shift clock)
RC6/TX/CK (pin)
Start Bit
Bit 0
Bit 1
WORD 1
Bit 7/8
Stop Bit
TXIF bit
(Transmit buffer
reg. empty flag)
WORD 1
Transmit Shift Reg
TRMT bit
(Transmit shift
reg. empty flag)
FIGURE 12-9: ASYNCHRONOUS MASTER TRANSMISSION (BACK TO BACK)
Write to TXREG reg
Word 2
Word 1
BRG output
(shift clock)
RC6/TX/CK (pin)
Start Bit
Start Bit
WORD 2
Bit 0
Bit 1
Bit 7/8
Bit 0
Stop Bit
TXIF bit
(interrupt reg. flag)
WORD 1
TRMT bit
(Transmit shift
reg. empty flag)
WORD 1
Transmit Shift Reg.
WORD 2
Transmit Shift Reg.
Note: This timing diagram shows two consecutive transmissions.
TABLE 12-6: REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION
Value on
POR,
BOR
Value on
all other
Resets
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(1)
0000 0000 0000 0000
0000 -00x 0000 -00x
0000 0000 0000 0000
0000 0000 0000 0000
0000 -010 0000 -010
0000 0000 0000 0000
0Ch
18h
19h
8Ch
PIR1
PSPIF
SPEN
(2)
RCIF
TXIF
SSPIF CCP1IF TMR2IF TMR1IF
FERR OERR RX9D
RCSTA
RX9
SREN CREN
—
TXREG USART Transmit Register
(1)
PIE1
PSPIE
CSRC
(2)
RCIE
TXIE SSPIE CCP1IE TMR2IE TMR1IE
SYNC BRGH TRMT TX9D
98h
99h
TXSTA
TX9
TXEN
—
SPBRG Baud Rate Generator Register
Legend: x= unknown, -= unimplemented locations read as '0'. Shaded cells are not used for Asynchronous Transmission.
Note 1: PSPIF and PSPIE are reserved on the PIC16C63/R63/66, always maintain these bits clear.
2: PIR1<6> and PIE1<6> are reserved, always maintain these bits clear.
1997 Microchip Technology Inc.
DS30234D-page 113
PIC16C6X
12.2.2 USART ASYNCHRONOUS RECEIVER
possible for two bytes of data to be received and trans-
ferred to the RCREG FIFO and a third byte begin shift-
ing to the RSR register. On the detection of the STOP
bit of the third byte, if the RCREG is still full, then the
overrun error bit, OERR (RCSTA<1>) will be set. The
word in the RSR register will be lost. The RCREG reg-
ister can be read twice to retrieve the two bytes in the
FIFO. Overrun bit OERR has to be cleared in software.
This is done by resetting the receive logic (CREN is
cleared and then set). If bit OERR is set, transfers from
the RSR register to the RCREG register are inhibited,
so it is essential to clear overrun bit OERR if it is set.
Framing error bit FERR (RCSTA<2>) is set if a stop bit
is detected as clear. Error bit FERR and the 9th receive
bit are buffered the same way as the receive data.
Reading the RCREG register will load bits RX9D and
FERR with new values. Therefore it is essential for the
user to read the RCSTA register before reading
RCREG in order not to lose the old FERR and RX9D
information.
The receiver block diagram is shown in Figure 12-10.
The data comes in the RC7/RX/DT pin and drives the
data recovery block.The data recovery block is actually
a high speed shifter operating at x16 times the baud
rate, whereas the main receive serial shifter operates
at the bit rate or at FOSC.
Once Asynchronous mode is selected, reception is
enabled by setting bit CREN (RCSTA<4>).
The heart of the receiver is the receive (serial) shift reg-
ister (RSR). After sampling the STOP bit, the received
data in the RSR is transferred to the RCREG register (if
it is empty). If the transfer is complete, flag bit RCIF
(PIR1<5>) is set. The actual interrupt can be
enabled/disabled by setting/clearing enable bit RCIE
(PIE1<5>). Flag bit RCIF is a read only bit which is
cleared by the hardware. It is cleared when the RCREG
register has been read and is empty. The RCREG is
double buffered register, i.e., it is a two deep FIFO. It is
FIGURE 12-10: USART RECEIVE BLOCK DIAGRAM
x64 Baud Rate CLK
FERR
OERR
CREN
SPBRG
÷ 64
RSR register
LSb
MSb
or
÷ 16
0
Baud Rate Generator
1
7
Stop (8)
Start
• • •
RC7/RX/DT
Pin Buffer
and Control
Data
Recovery
RX9
RX9D
SPEN
RCREG register
FIFO
8
RCIF
RCIE
Interrupt
Data Bus
FIGURE 12-11: ASYNCHRONOUS RECEPTION
Start
bit
Start
bit
Start
bit
RC7/RX/DT (pin)
bit0
bit1
Stop
bit
Stop
bit
bit7/8 Stop
bit
bit0
bit7/8
bit7/8
Rcv shift
reg
Rcv buffer reg
WORD 2
RCREG
WORD 1
RCREG
Read Rcv
buffer reg
RCREG
RCIF
(interrupt flag)
OERR bit
CREN bit
Note: This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word,
causing overrun error bit OERR to be set.
DS30234D-page 114
1997 Microchip Technology Inc.
PIC16C6X
Steps to follow when setting up an Asynchronous
Reception:
6. Flag bit RCIF will be set when reception is com-
plete, and an interrupt will be generated if
enable bit RCIE was set.
1. Initialize the SPBRG register for the appropriate
baud rate. If a high speed baud rate is desired,
set bit BRGH (Section 12.1).
7. Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
2. Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
8. Read the 8-bit received data by reading the
RCREG register.
3. If interrupts are desired, then set enable bit
RCIE.
9. If any error occurred, clear the error by clearing
enable bit CREN.
4. If 9-bit reception is desired, then set bit RX9.
5. Enable the reception by setting enable bit
CREN.
TABLE 12-7: REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION
Value on
POR,
BOR
Value on
all other
Resets
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(1)
0Ch
18h
1Ah
8Ch
98h
99h
PIR1
PSPIF
SPEN
(2)
RCIF
TXIF
SSPIF CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
RCSTA
RX9
SREN CREN
—
FERR
OERR
RX9D
0000 -00x 0000 -00x
0000 0000 0000 0000
RCREG USART Receive Register
(1)
PIE1
PSPIE
CSRC
(2)
RCIE
TXIE SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
TXSTA
TX9
TXEN
SYNC
—
BRGH
TRMT
TX9D
0000 -010 0000 -010
0000 0000 0000 0000
SPBRG Baud Rate Generator Register
Legend: x= unknown, -= unimplemented locations read as '0'. Shaded cells are not used for Asynchronous Reception.
Note 1: PSPIE and PSPIF are reserved on the PIC16C63/R63/66, always maintain these bits clear.
2: PIE1<6> and PIR1<6> are reserved, always maintain these bits clear.
1997 Microchip Technology Inc.
DS30234D-page 115
PIC16C6X
Clearing enable bit TXEN, during a transmission, will
cause the transmission to be aborted and will reset the
transmitter. The DT and CK pins will revert to hi-imped-
ance. If, during a transmission, either bit CREN or bit
SREN is set the transmission is aborted and the DT pin
reverts to a hi-impedance state (for a reception). The
CK pin will remain an output if bit CSRC is set (internal
clock). The transmitter logic however, is not reset
although it is disconnected from the pins. In order to
reset the transmitter, the user has to clear enable bit
TXEN. If enable bit SREN is set (to interrupt an on
going transmission and receive a single word), then
after the single word is received, enable bit SREN will
be cleared, and the serial port will revert back to trans-
mitting since enable bit TXEN is still set. The DT line
will immediately switch from hi-impedance receive
mode to transmit and start driving.To avoid this, enable
bit TXEN should be cleared.
12.3
USART Synchronous Master Mode
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
In Synchronous Master mode the data is transmitted in
a half-duplex manner i.e., transmission and reception
do not occur at the same time. When transmitting data
the reception is inhibited and vice versa. Synchronous
mode is entered by setting bit SYNC (TXSTA<4>). In
addition enable bit SPEN (RCSTA<7>) is set in order to
configure the RC6 and RC7 I/O pins to CK (clock) and
DT (data) lines respectively. The Master mode indi-
cates that the processor transmits the master clock on
the CK line. The Master mode is entered by setting bit
CSRC (TXSTA<7>).
12.3.1 USART SYNCHRONOUS MASTER
TRANSMISSION
The USART transmitter block diagram is shown in
Figure 12-7. The heart of the transmitter is the transmit
(serial) shift register (TSR).The shift register obtains its
data from the read/write transmit buffer register,
TXREG. The TXREG register is loaded with data in
software. The TSR register is not loaded until the last
bit has been transmitted from the previous load. As
soon as the last bit is transmitted, the TSR register is
loaded with new data from the TXREG register (if avail-
able). Once the TXREG register transfers the data to
the TSR register (occurs in one Tcycle), the TXREG
register is empty and interrupt flag bit TXIF (PIR1<4>)
is set. This interrupt can be enabled/disabled by set-
ting/clearing enable bit TXIE (PIE1<4>). Flag bit TXIF
will be set regardless of the status of enable bit TXIE
and cannot be cleared in software. It will clear only
when new data is loaded into the TXREG register.
While flag bit TXIF indicates the status of the TXREG
register, another bit, TRMT (TXSTA<1>), shows the
status of the TSR register. Status bit TRMT is a read
only bit which is set when the TSR register is empty. No
interrupt logic is tied to this bit, so the user has to poll
this bit in order to determine if the TSR register is
empty.The TSR register is not mapped in data memory
so it is not available to the user.
In order to select 9-bit transmission, bit TX9
(TXSTA<6>) should be set and the ninth bit should be
written to bit TX9D (TXSTA<0>). The ninth bit must be
written before writing the 8-bit data to the TXREG reg-
ister. This is because a data write to the TXREG regis-
ter can result in an immediate transfer of the data to the
TSR register (if the TSR is empty). If the TSR register
was empty and the TXREG register was written before
writing the “new” TX9D, the “present” value of bit TX9D
is loaded.
Steps to follow when setting up a Synchronous Master
Transmission:
1. Initialize the SPBRG register for the appropriate
baud rate (Section 12.1).
2. Enable the synchronous master serial port by
setting bits SYNC, SPEN, and CSRC.
3. If interrupts are desired, then set enable bit
TXIE.
4. If 9-bit transmission is desired, then set bit TX9.
5. Enable the transmission by setting enable bit
TXEN.
6. If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
7. Start transmission by loading data to the
TXREG register.
Transmission is enabled by setting enable bit TXEN
(TXSTA<5>). The actual transmission will not occur
until the TXREG register has been loaded with data.
The first data bit will be shifted out on the next available
rising edge of the clock on the CK line. Data out is sta-
ble around the falling edge of the synchronous clock
(Figure 12-12).The transmission can also be started by
first loading the TXREG register and then setting
enable bit TXEN (Figure 12-13). This is advantageous
when slow baud rates are selected, since the BRG is
kept in reset when bits TXEN, CREN, and SREN are
clear. Setting enable bit TXEN will start the BRG, cre-
ating a shift clock immediately. Normally when trans-
mission is first started, the TSR register is empty, so a
transfer to the TXREG register will result in an immedi-
ate transfer to TSR resulting in an empty TXREG reg-
ister. Back-to-back transfers are possible.
DS30234D-page 116
1997 Microchip Technology Inc.
PIC16C6X
TABLE 12-8:
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTERTRANSMISSION
Value on
POR,
BOR
Value on
all other
Resets
Address Name
Bit 7
Bit 6
(2)
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(1)
0Ch
18h
19h
8Ch
98h
99h
PIR1
PSPIF
SPEN
RCIF
TXIF SSPIF CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
RCSTA
RX9 SREN CREN
—
FERR
OERR
RX9D
0000 -00x 0000 -00x
0000 0000 0000 0000
TXREG USART Transmit Register
(1)
PIE1
PSPIE
CSRC
(2)
RCIE
TXIE SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
TXSTA
TX9
TXEN SYNC
—
BRGH
TRMT
TX9D
0000 -010 0000 -010
0000 0000 0000 0000
SPBRG Baud Rate Generator Register
Legend: x= unknown, -= unimplemented locations read as '0'. Shaded cells are not used for Synchronous Master Transmission.
Note 1: PSPIE and PSPIF are reserved on the PIC16C63/R63/66, always maintain these bits clear.
2: PIE1<6> and PIR1<6> are reserved, always maintain these bits clear.
FIGURE 12-12: SYNCHRONOUS TRANSMISSION
Q1Q2 Q3Q4 Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2 Q3Q4
Q3Q4 Q1Q2 Q3Q4 Q1Q2 Q3Q4 Q1Q2 Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4
RC7/RX/DT pin
RC6/TX/CK pin
Bit 0
Bit 1
Bit 2
Bit 7
Bit 0
Bit 1
WORD 2
Bit 7
WORD 1
Write to
TXREG reg
Write word1
Write word2
TXIF bit
(Interrupt flag)
TRMT bit
'1'
Note: Sync master mode; SPBRG = '0'. Continuous transmission of two 8-bit words
'1'
TXEN bit
FIGURE 12-13: SYNCHRONOUS TRANSMISSION THROUGH TXEN
RC7/RX/DT pin
RC6/TX/CK pin
bit0
bit2
bit1
bit6
bit7
Write to
TXREG reg
TXIF bit
TRMT bit
TXEN bit
1997 Microchip Technology Inc.
DS30234D-page 117
PIC16C6X
12.3.2 USART SYNCHRONOUS MASTER
RECEPTION
Steps to follow when setting up Synchronous Master
Reception:
1. Initialize the SPBRG register for the appropriate
baud rate (Section 12.1).
Once Synchronous Mode is selected, reception is
enabled by setting either enable bit SREN
(RCSTA<5>) bit or enable bit CREN (RCSTA<4>).
Data is sampled on the DT pin on the falling edge of the
clock. If enable bit SREN is set, then only a single word
is received. If enable bit CREN is set, the reception is
continuous until bit CREN is cleared. If both the bits are
set then bit CREN takes precedence. After clocking the
last bit, the received data in the Receive Shift Register
(RSR) is transferred to the RCREG register (if it is
empty). When the transfer is complete, interrupt bit
RCIF (PIR1<5>) is set. The actual interrupt can be
enabled/disabled by setting/clearing enable bit RCIE
(PIE1<5>). Flag bit RCIF is a read only bit which is
reset by the hardware. In this case, it is reset when the
RCREG register has been read and is empty. The
RCREG is a double buffered register, i.e., it is a two
deep FIFO. It is possible for two bytes of data to be
received and transferred to the RCREG FIFO and a
third byte to begin shifting into the RSR register. On the
clocking of the last bit of the third byte, if the RCREG
register is still full, then overrun error bit, OERR
(RCSTA<1>) is set. The word in the RSR register will
be lost. The RCREG register can be read twice to
retrieve the two bytes in the FIFO. Overrun error bit
OERR has to be cleared in software (by clearing bit
CREN). If bit OERR is set, transfers from the RSR to
the RCREG are inhibited, so it is essential to clear bit
OERR if it is set. The 9th receive bit is buffered the
same way as the receive data. Reading the RCREG
register will load bit RX9D with a new value. Therefore
it is essential for the user to read the RCSTA register
before reading the RCREG register in order not to lose
the old RX9D bit information.
2. Enable the synchronous master serial port by
setting bits SYNC, SPEN, and CSRC.
3. Ensure bits CREN and SREN are clear.
4. If interrupts are desired, then set enable bit
RCIE.
5. If 9-bit reception is desired, then set bit RX9.
6. If a single reception is required, set enable bit
SREN. For continuous reception set enable bit
CREN.
7. Flag bit RCIF will be set when reception is com-
plete and an interrupt will be generated if enable
bit RCIE was set.
8. Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
9. Read the 8-bit received data by reading the
RCREG register.
10. If any error occurred, clear the error by clearing
enable bit CREN.
TABLE 12-9: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Value on
POR,
BOR
Value on
all other
Resets
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(1)
(2)
0Ch
18h
1Ah
8Ch
98h
99h
PIR1
PSPIF
SPEN
RCIF
TXIF SSPIF CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
RCSTA
RX9 SREN CREN
—
FERR
OERR
RX9D
0000 -00x 0000 -00x
0000 0000 0000 0000
RCREG USART Receive Register
(1)
(2)
PIE1
PSPIE
CSRC
RCIE
TXIE SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
TXSTA
TX9
TXEN SYNC
—
BRGH
TRMT
TX9D
0000 -010 0000 -010
0000 0000 0000 0000
SPBRG Baud Rate Generator Register
Legend: x= unknown, -= unimplemented locations read as '0'. Shaded cells are not used for Synchronous Master Reception.
Note 1: PSPIF and PSPIE are reserved on the PIC16C63/R63/66, always maintain these bits clear.
2: PIR1<6> and PIE1<6> are reserved, always maintain these bits clear.
DS30234D-page 118
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 12-14: SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RC7/RX/DT pin
RC6/TX/CK pin
bit0
bit1
bit2
bit3
bit4
bit5
bit6
bit7
Write to
bit SREN
SREN bit
CREN bit
'0'
'0'
RCIF bit
(interrupt)
Read
RXREG
Note: Timing diagram demonstrates SYNC master mode with bit SREN = '1' and bit BRG = '0'.
1997 Microchip Technology Inc.
DS30234D-page 119
PIC16C6X
12.4.2 USART SYNCHRONOUS SLAVE
RECEPTION
12.4
USART Synchronous Slave Mode
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The operation of the synchronous master and slave
modes is identical except in the case of the SLEEP
mode. Also, enable bit SREN is a don't care in slave
mode.
Synchronous Slave Mode differs from Master Mode in
the fact that the shift clock is supplied externally at the
CK pin (instead of being supplied internally in master
mode). This allows the device to transfer or receive
data while in SLEEP mode. Slave mode is entered by
clearing bit CSRC (TXSTA<7>).
If receive is enabled by setting bit CREN prior to the
SLEEPinstruction, then a word may be received during
SLEEP. On completely receiving the word, the RSR
register will transfer the data to the RCREG register
and if enable bit RCIE is set, the interrupt generated will
wake the chip from SLEEP. If the global interrupt is
enabled, the program will branch to the interrupt vector
(0004h).
12.4.1 USART SYNCHRONOUS SLAVE
TRANSMIT
The operation of the synchronous master and slave
modes are identical except in the case of the SLEEP
mode.
Steps to follow when setting up a Synchronous Slave
Reception:
If two words are written to the TXREG and then the
SLEEPinstruction is executed, the following will occur:
1. Enable the synchronous master serial port by
setting bits SYNC and SPEN, and clearing bit
CSRC.
a) The first word will immediately transfer to the
TSR register and transmit.
b) The second word will remain in TXREG register.
c) Flag bit TXIF will not be set.
2. If interrupts are desired, then set enable bit
RCIE.
d) When the first word has been shifted out of TSR,
the TXREG register will transfer the second
word to the TSR and flag bit TXIF will now be
set.
3. If 9-bit reception is desired, then set bit RX9.
4. To enable reception, set enable bit CREN.
5. Flag bit RCIF will be set when reception is com-
plete, and an interrupt will be generated if
enable bit RCIE was set.
e) If enable bit TXIE is set, the interrupt will wake
the chip from SLEEP and if the global interrupt
is enabled, the program will branch to the inter-
rupt vector (0004h).
6. Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
Steps to follow when setting up Synchronous Slave
Transmission:
7. Read the 8-bit received data by reading the
RCREG register.
1. Enable the synchronous slave serial port by set-
ting bits SYNC and SPEN, and clearing bit
CSRC.
8. If any error occurred, clear the error by clearing
enable bit CREN.
2. Clear bits CREN and SREN.
3. If interrupts are desired, then set enable bit
TXIE.
4. If 9-bit transmission is desired, then set bit TX9.
5. Enable the transmission by setting bit TXEN.
6. If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
7. Start transmission by loading data to the
TXREG register.
DS30234D-page 120
1997 Microchip Technology Inc.
PIC16C6X
TABLE 12-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
Value on
POR,
BOR
Value on
all other
Resets
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(1)
0000 0000 0000 0000
0000 -00x 0000 -00x
0000 0000 0000 0000
0000 0000 0000 0000
0000 -010 0000 -010
0000 0000 0000 0000
0Ch
18h
19h
8Ch
98h
99h
PIR1
PSPIF
(2)
RCIF
TXIF
SSPIF CCP1IF TMR2IF TMR1IF
FERR OERR RX9D
RCSTA
SPEN
RX9
SREN
CREN
—
TXREG USART Transmit Register
(1)
PIE1
PSPIE
(2)
RCIE
TXIE
SSPIE CCP1IE TMR2IE TMR1IE
BRGH TRMT TX9D
TXSTA
CSRC
TX9
TXEN
SYNC
—
SPBRG Baud Rate Generator Register
Legend: x= unknown, -= unimplemented locations read as '0'. Shaded cells are not used for Synchronous Slave Transmission.
Note 1: PSPIF and PSPIE are reserved on the PIC16C63/R63/66, always maintain these bits clear.
2: PIR1<6> and PIE1<6> are reserved, always maintain these bits clear.
TABLE 12-11: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
Value on
POR,
BOR
Value on
all other
Resets
Address Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(1)
0000 0000 0000 0000
0000 -00x 0000 -00x
0000 0000 0000 0000
0000 0000 0000 0000
0000 -010 0000 -010
0000 0000 0000 0000
0Ch
18h
1Ah
8Ch
98h
99h
PIR1
PSPIF
SPEN
(2)
RCIF
TXIF SSPIF CCP1IF TMR2IF TMR1IF
FERR OERR RX9D
RCSTA
RX9
SREN CREN
—
RCREG USART Receive Register
(1)
PIE1
PSPIE
CSRC
(2)
RCIE
TXIE SSPIE CCP1IE TMR2IE TMR1IE
BRGH TRMT TX9D
TXSTA
TX9
TXEN SYNC
—
SPBRG Baud Rate Generator Register
Legend: x= unknown, -= unimplemented locations read as '0'. Shaded cells are not used for Synchronous Slave Reception.
Note 1: PSPIF and PSPIE are reserved on the PIC16C63/R63/66, always maintain these bits clear.
2: PIR1<6> and PIE1<6> are reserved, always maintain these bits clear.
1997 Microchip Technology Inc.
DS30234D-page 121
PIC16C6X
NOTES:
DS30234D-page 122
1997 Microchip Technology Inc.
PIC16C6X
timers that offer necessary delays on power-up. One is
the Oscillator Start-up Timer (OST), intended to keep
the chip in RESET until the crystal oscillator is stable.
The other is the Power-up Timer (PWRT), which pro-
vides a fixed delay of 72 ms (nominal) on power-up
only, designed to keep the part in reset while the power
supply stabilizes. With these two timers on-chip, most
applications need no external reset circuitry.
13.0 SPECIAL FEATURES OF THE
CPU
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
What sets a microcontroller apart from other proces-
sors are special circuits to deal with the needs of real-
time applications. The PIC16CXX family has a host of
such features intended to maximize system reliability,
minimize cost through elimination of external compo-
nents, provide power saving operating modes and offer
code protection. These are:
SLEEP mode is designed to offer a very low current
power-down mode. The user can wake from SLEEP
through external reset, Watchdog Timer Wake-up or
through an interrupt. Several oscillator options are also
made available to allow the part to fit the application.
The RC oscillator option saves system cost while the
LP crystal option saves power. A set of configuration
bits are used to select various options.
• Oscillator selection
• Reset
- Power-on Reset (POR)
- Power-up Timer (PWRT)
- Oscillator Start-up Timer (OST)
- Brown-out Reset (BOR)
• Interrupts
13.1
Configuration Bits
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
• Watchdog Timer (WDT)
• SLEEP mode
The configuration bits can be programmed (read as '0')
or left unprogrammed (read as '1') to select various
device configurations. These bits are mapped in pro-
gram memory location 2007h.
• Code protection
• ID locations
The user will note that address 2007h is beyond the
user program memory space. In fact, it belongs to the
special test/configuration memory space (2000h -
3FFFh), which can be accessed only during program-
ming.
• In-circuit serial programming
The PIC16CXX has a Watchdog Timer which can be
shut off only through configuration bits. It runs off its
own RC oscillator for added reliability. There are two
FIGURE 13-1: CONFIGURATION WORD FOR PIC16C61
—
—
—
—
—
—
—
—
—
CP0 PWRTE WDTE FOSC1 FOSC0
bit0
Register: CONFIG
Address 2007h
bit13
bit 13-5: Unimplemented: Read as '1'
bit 4:
bit 3:
bit 2:
CP0: Code protection bit
1 = Code protection off
0 = All memory is code protected, but 00h - 3Fh is writable
PWRTE: Power-up Timer Enable bit
1 = Power-up Timer enabled
0 = Power-up Timer disabled
WDTE: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled
bit 1-0: FOSC1:FOSC0: Oscillator Selection bits
11= RC oscillator
10= HS oscillator
01= XT oscillator
00= LP oscillator
1997 Microchip Technology Inc.
DS30234D-page 123
PIC16C6X
FIGURE 13-2: CONFIGURATION WORD FOR PIC16C62/64/65
—
—
—
—
—
—
—
—
CP1
CP0 PWRTE WDTE FOSC1 FOSC0
bit0
Register: CONFIG
Address 2007h
bit13
bit 13-6: Unimplemented: Read as '1'
bit 5-4: CP1:CP0: Code Protection bits
11= Code protection off
10= Upper half of program memory code protected
01= Upper 3/4th of program memory code protected
00= All memory is code protected
bit 3:
bit 2:
PWRTE: Power-up Timer Enable bit
1 = Power-up Timer enabled
0 = Power-up Timer disabled
WDTE: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled
bit 1-0: FOSC1:FOSC0: Oscillator Selection bits
11= RC oscillator
10= HS oscillator
01= XT oscillator
00= LP oscillator
FIGURE 13-3: CONFIGURATION WORD FOR PIC16C62A/R62/63/R63/64A/R64/65A/R65/66/67
CP1
CP0
CP1
CP0
CP1
CP0
—
BODEN CP1
CP0 PWRTE WDTE FOSC1 FOSC0
bit0
Register: CONFIG
Address 2007h
bit13
(2)
bit 13-8: CP1:CP0: Code Protection bits
bit 5:4
11= Code protection off
10= Upper half of program memory code protected
01= Upper 3/4th of program memory code protected
00= All memory is code protected
bit 7:
bit 6:
Unimplemented: Read as '1'
(1)
BODEN: Brown-out Reset Enable bit
1 = Brown-out Reset enabled
0 = Brown-out Reset disabled
(1)
bit 3:
bit 2:
PWRTE: Power-up Timer Enable bit
1 = Power-up Timer disabled
0 = Power-up Timer enabled
WDTE: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled
bit 1-0: FOSC1:FOSC0: Oscillator Selection bits
11= RC oscillator
10= HS oscillator
01= XT oscillator
00= LP oscillator
Note 1: Enabling Brown-out Reset automatically enables Power-up Timer (PWRT) regardless of the value of bit PWRTE.
Ensure the Power-up Timer is enabled anytime Brown-out Reset is enabled.
2: All of the CP1:CP0 pairs have to be given the same value to implement the code protection scheme listed.
DS30234D-page 124
1997 Microchip Technology Inc.
PIC16C6X
13.2
Oscillator Configurations
FIGURE 13-4: CRYSTAL/CERAMIC
RESONATOR OPERATION
(HS, XT OR LP OSC
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
CONFIGURATION)
13.2.1
OSCILLATOR TYPES
The PIC16CXX can be operated in four different oscil-
lator modes. The user can program two configuration
bits (FOSC1 and FOSC0) to select one of these four
modes:
OSC1
To internal
(2)
logic
C1
C2
XTAL
OSC2
SLEEP
PIC16CXX
RF
• LP
• XT
• HS
• RC
Low Power Crystal
To internal
logic
RS
Note1
Crystal/Resonator
(2)
High Speed Crystal/Resonator
Resistor/Capacitor
See Table 13-1, Table 13-3, Table 13-2 and Table 13-4 for
recommended values of C1 and C2.
13.2.2 CRYSTAL OSCILLATOR/CERAMIC
RESONATORS
Note 1: A series resistor may be required for AT strip
cut crystals.
In LP, XT, or HS modes a crystal or ceramic resonator
is connected to the OSC1/CLKIN and OSC2/CLKOUT
pins to establish oscillation (Figure 13-4). The
PIC16CXX oscillator design requires the use of a par-
allel cut crystal. Use of a series cut crystal may give a
frequency out of the crystal manufacturers specifica-
tions. When in LP, XT, or HS modes, the device can
have an external clock source to drive the OSC1/CLKIN
pin (Figure 13-5).
2: For the PIC16C61 the buffer is on the OSC2
pin, all other devices have the buffer on the
OSC1 pin.
FIGURE 13-5: EXTERNAL CLOCK INPUT
OPERATION (HS, XT OR LP
OSC CONFIGURATION)
OSC1
OSC2
Clock from
ext. system
PIC16CXX
Open
1997 Microchip Technology Inc.
DS30234D-page 125
PIC16C6X
TABLE 13-1: CERAMIC RESONATORS
PIC16C61
TABLE 13-3: CAPACITOR SELECTION
FOR CRYSTAL OSCILLATOR
FOR PIC16C61
Ranges Tested:
Mode
Freq
OSC1
OSC2
Mode
XT
Freq
OSC1
OSC2
LP
33 - 68 pF
15 - 47 pF
33 - 68 pF
15 - 47 pF
32 kHz
200 kHz
455 kHz
2.0 MHz
4.0 MHz
47 - 100 pF 47 - 100 pF
15 - 68 pF 15 - 68 pF
15 - 68 pF 15 - 68 pF
XT
100 kHz
500 kHz
1 MHz
2 MHz
4 MHz
47 - 100 pF
20 - 68 pF
15 - 68 pF
15 - 47 pF
15 - 33 pF
47 - 100 pF
20 - 68 pF
15 - 68 pF
15 - 47 pF
15 - 33 pF
HS
8.0 MHz
16.0 MHz
15 - 68 pF 15 - 68 pF
10 - 47 pF 10 - 47 pF
These values are for design guidance only. See
notes at bottom of page.
HS
8 MHz
20 MHz
15 - 47 pF
15 - 47 pF
15 - 47 pF
15 - 47 pF
Resonators Used:
455 kHz
Panasonic EFO-A455K04B ± 0.3%
These values are for design guidance only. See
2.0 MHz Murata Erie CSA2.00MG
4.0 MHz Murata Erie CSA4.00MG
8.0 MHz Murata Erie CSA8.00MT
± 0.5%
± 0.5%
± 0.5%
notes at bottom of page.
TABLE 13-4: CAPACITOR SELECTION
FOR CRYSTAL OSCILLATOR
FOR PIC16C62/62A/R62/63/
R63/64/64A/R64/65/65A/R65/
66/67
16.0 MHz Murata Erie CSA16.00MX ± 0.5%
All resonators used did not have built-in capacitors.
TABLE 13-2: CERAMIC RESONATORS
PIC16C62/62A/R62/63/R63/64/
64A/R64/65/65A/R65/66/67
Cap.
Range
C2
Crystal
Freq
Cap. Range
C1
Osc Type
Ranges Tested:
LP
32 kHz
200 kHz
200 kHz
1 MHz
33 pF
15 pF
33 pF
15 pF
Mode
XT
Freq
OSC1
OSC2
455 kHz
2.0 MHz
4.0 MHz
68 - 100 pF
15 - 68 pF
15 - 68 pF
68 - 100 pF
15 - 68 pF
15 - 68 pF
XT
HS
47-68 pF
15 pF
47-68 pF
15 pF
HS
8.0 MHz
16.0 MHz
10 - 68 pF
10 - 22 pF
10 - 68 pF
10 - 22 pF
4 MHz
15 pF
15 pF
4 MHz
15 pF
15 pF
These values are for design guidance only. See
notes at bottom of page.
8 MHz
15-33 pF
15-33 pF
15-33 pF
15-33 pF
20 MHz
Resonators Used:
These values are for design guidance only. See
notes at bottom of page.
455 kHz Panasonic EFO-A455K04B ± 0.3%
2.0 MHz Murata Erie CSA2.00MG
4.0 MHz Murata Erie CSA4.00MG
8.0 MHz Murata Erie CSA8.00MT
16.0 MHz Murata Erie CSA16.00MX
± 0.5%
± 0.5%
± 0.5%
± 0.5%
Crystals Used
32 kHz
Epson C-001R32.768K-A
± 20 PPM
± 20 PPM
± 50 PPM
± 50 PPM
200 kHz STD XTL 200.000KHz
1 MHz
4 MHz
8 MHz
ECS ECS-10-13-1
ECS ECS-40-20-1
All resonators used did not have built-in capacitors.
EPSON CA-301 8.000M-C ± 30 PPM
20 MHz EPSON CA-301 20.000M-C ± 30 PPM
Note 1: Recommended values of C1 and C2 are identical to the ranges tested Table 13-1 and Table 13-2.
2: Higher capacitance increases the stability of oscillator but also increases the start-up time.
3: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal man-
ufacturer for appropriate values of external components.
4: Rs may be required in HS mode as well as XT mode to avoid overdriving crystals with low drive level speci-
fication.
DS30234D-page 126
1997 Microchip Technology Inc.
PIC16C6X
13.2.3 EXTERNAL CRYSTAL OSCILLATOR
CIRCUIT
13.2.4 RC OSCILLATOR
For timing insensitive applications the RC device option
offers additional cost savings. The RC oscillator fre-
quency is a function of the supply voltage, the resistor
(Rext) and capacitor (Cext) values, and the operating
temperature. In addition to this, the oscillator frequency
will vary from unit to unit due to normal process param-
eter variation. Furthermore, the difference in lead frame
capacitance between package types will also affect the
oscillation frequency, especially for low Cext values.
The user also needs to take into account variation due
to tolerance of external R and C components used.
Figure 13-8 shows how the RC combination is con-
nected to the PIC16CXX. For Rext values below
2.2 kΩ, the oscillator operation may become unstable
or stop completely. For very high Rext values (e.g.
1 MΩ), the oscillator becomes sensitive to noise,
humidity and leakage. Thus, we recommend keeping
Rext between 3 kΩ and 100 kΩ.
Either a prepackaged oscillator can be used or a simple
oscillator circuit with TTL gates can be built. Prepack-
aged oscillators provide a wide operating range and
better stability. A well-designed crystal oscillator will
provide good performance with TTL gates. Two types
of crystal oscillator circuits can be used; one with series
resonance, or one with parallel resonance.
Figure 13-6 shows implementation of a parallel reso-
nant oscillator circuit. The circuit is designed to use the
fundamental frequency of the crystal. The 74AS04
inverter performs the 180-degree phase shift that a par-
allel oscillator requires. The 4.7 kΩ resistor provides
the negative feedback for stability. The 10 kΩ potenti-
ometer biases the 74AS04 in the linear region. This
could be used for external oscillator designs.
FIGURE 13-6: EXTERNAL PARALLEL
RESONANT CRYSTAL
Although the oscillator will operate with no external
capacitor (Cext = 0 pF), we recommend using values
above 20 pF for noise and stability reasons. With no or
small external capacitance, the oscillation frequency
can vary dramatically due to changes in external
capacitances, such as PCB trace capacitance or pack-
age lead frame capacitance.
OSCILLATOR CIRCUIT
+5V
To Other
Devices
10k
74AS04
4.7k
PIC16CXX
CLKIN
74AS04
See characterization data for desired device for RC fre-
quency variation from part to part due to normal pro-
cess variation.The variation is larger for larger R (since
leakage current variation will affect RC frequency more
for large R) and for smaller C (since variation of input
capacitance will affect RC frequency more).
10k
XTAL
10k
See characterization data for desired device for varia-
tion of oscillator frequency due to VDD for given Rext/
Cext values as well as frequency variation due to oper-
ating temperature for given R, C, and VDD values.
20 pF
20 pF
Figure 13-7 shows a series resonant oscillator circuit.
This circuit is also designed to use the fundamental fre-
quency of the crystal. The inverter performs a 180-
degree phase shift in a series resonant oscillator cir-
cuit. The 330 kΩ resistors provide the negative feed-
back to bias the inverters in their linear region.
The oscillator frequency, divided by 4, is available on
the OSC2/CLKOUT pin, and can be used for test pur-
poses or to synchronize other logic (see Figure 3-5 for
waveform).
FIGURE 13-8: RC OSCILLATOR MODE
FIGURE 13-7: EXTERNAL SERIES
RESONANT CRYSTAL
VDD
OSCILLATOR CIRCUIT
Rext
Internal
OSC1
To Other
Devices
clock
330 kΩ
330 kΩ
Cext
74AS04
74AS04
74AS04
PIC16CXX
PIC16CXX
VSS
CLKIN
0.1 µF
OSC2/CLKOUT
Fosc/4
XTAL
1997 Microchip Technology Inc.
DS30234D-page 127
PIC16C6X
The TO and PD bits are set or cleared differently in dif-
ferent reset situations as indicated in Table 13-7,
Table 13-8, and Table 13-9.These bits are used in soft-
ware to determine the nature of the reset. See
Table 13-12 for a full description of reset states of all
registers.
13.3
Reset
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The PIC16CXX differentiates between various kinds of
reset:
• Power-on Reset (POR)
A simplified block diagram of the on-chip reset circuit is
shown in Figure 13-9.
• MCLR reset during normal operation
• MCLR reset during SLEEP
• WDT Reset (normal operation)
On the PIC16C62A/R62/63/R63/64A/R64/65A/R65/
66/67, the MCLR reset path has a noise filter to detect
and ignore small pulses. See parameter #34 for pulse
width specifications.
• Brown-out Reset (BOR) - Not on PIC16C61/62/
64/65
Some registers are not affected in any reset condition,
their status is unknown on POR and unchanged in any
other reset. Most other registers are reset to a “reset
state” on Power-on Reset (POR), on MCLR or WDT
Reset, on MCLR reset during SLEEP, and on Brown-
out Reset (BOR). They are not affected by a WDT
Wake-up, which is viewed as the resumption of normal
operation.
It should be noted that a WDT Reset does not drive the
MCLR pin low.
FIGURE 13-9: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
External Reset
MCLR/VPP pin
SLEEP
WDT
Module
WDT
Time-out
VDD rise
detect
Power-on Reset
VDD pin
(2)
Brown-out
Reset
S
R
BODEN
OST/PWRT
OST
Chip Reset
10-bit Ripple counter
OSC1/
Q
CLKIN
pin
(1)
PWRT
10-bit Ripple counter
On-chip
RC OSC
Enable PWRT
(3)
Enable OST
Note 1: This is a separate oscillator from the RC oscillator of the CLKIN pin.
2: Brown-out Reset is NOT implemented on the PIC16C61/62/64/65.
3: See Table 13-5 and Table 13-6 for time-out situations.
DS30234D-page 128
1997 Microchip Technology Inc.
PIC16C6X
The power-up time delay will vary from chip to chip due
to VDD, temperature, and process variation. See DC
parameters for details.
13.4
Power-on Reset (POR), Power-up
Timer (PWRT), Oscillator Start-up
Timer (OST) and Brown-out Reset
(BOR)
13.4.3 OSCILLATOR START-UP TIMER (OST)
Applicable Devices
The Oscillator Start-up Timer (OST) provides 1024
oscillator cycle (from OSC1 input) delay after the
PWRT delay is over. This ensures the crystal oscillator
or resonator has started and stabilized.
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
13.4.1 POWER-ON RESET (POR)
A Power-on Reset pulse is generated on-chip when
VDD rise is detected (in the range of 1.5V - 2.1V). To
take advantage of the POR, just tie the MCLR/VPP pin
directly (or through a resistor) to VDD. This will elimi-
nate external RC components usually needed to create
a Power-on Reset. A maximum rise time for VDD is
required. See Electrical Specifications for details.
The OST time-out is invoked only for XT, LP and HS
modes and only on Power-on Reset or wake-up from
SLEEP.
13.4.4 BROWN-OUT RESET (BOR)
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
When the device starts normal operation (exits the
reset condition), device operating parameters (voltage,
frequency, temperature, ...) must be met to ensure
operation. If these conditions are not met, the device
must be held in reset until the operating conditions are
met. Brown-out Reset may be used to meet the startup
conditions.
A configuration bit, BODEN, can disable (if clear/pro-
grammed) or enable (if set) the Brown-out Reset cir-
cuitry. If VDD falls below 4.0V (parameter D005 in
Electrical Specification section) for greater than param-
eter #34 (see Electrical Specification section), the
brown-out situation will reset the chip. A reset may not
occur if VDD falls below 4.0V for less than parameter
#34. The chip will remain in Brown-out Reset until VDD
rises above BVDD. The Power-up Timer will now be
invoked and will keep the chip in RESET an additional
72 ms. If VDD drops below BVDD while the Power-up
Timer is running, the chip will go back into a Brown-out
Reset and the Power-up Timer will be initialized. Once
VDD rises above BVDD, the Power-up Timer will exe-
cute a 72 ms time delay. The Power-up Timer should
always be enabled when Brown-out Reset is enabled.
Figure 13-10 shows typical brown-out situations.
For additional information, refer to Application Note
AN607, “Power-up Trouble Shooting.”
13.4.2 POWER-UP TIMER (PWRT)
The Power-up Timer provides a fixed 72 ms nominal
time-out on power-up only, from POR. The Power-up
Timer operates on an internal RC oscillator.The chip is
kept in reset as long as PWRT is active. The PWRT’s
time delay allows VDD to rise to an acceptable level. A
configuration bit is provided to enable/disable the
PWRT.
FIGURE 13-10: BROWN-OUT SITUATIONS
VDD
BVDD Max.
BVDD Min.
Internal
Reset
72 ms
VDD
BVDD Max.
BVDD Min.
Internal
Reset
<72 ms
72 ms
VDD
BVDD Max.
BVDD Min.
Internal
Reset
72 ms
1997 Microchip Technology Inc.
DS30234D-page 129
PIC16C6X
13.4.5 TIME-OUT SEQUENCE
13.4.6 POWER CONTROL/STATUS REGISTER
(PCON)
On power-up the time-out sequence is as follows: First
a PWRT time-out is invoked after the POR time delay
has expired. Then OST is activated. The total time-out
will vary based on oscillator configuration and the sta-
tus of the PWRT. For example, in RC mode, with the
PWRT disabled, there will be no time-out at all.
Figure 13-11, Figure 13-12, and Figure 13-13 depict
time-out sequences on power-up.
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The Power Control/Status Register, PCON has up to
two bits, depending upon the device. Bit0 is not imple-
mented on the PIC16C62/64/65.
Bit0 is BOR (Brown-out Reset Status bit). BOR is
unknown on Power-on Reset. It must then be set by the
user and checked on subsequent resets to see if BOR
cleared, indicating that a brown-out has occurred. The
BOR status bit is a “Don’t Care” and is not necessarily
predictable if the Brown-out Reset circuitry is disabled
(by clearing bit BODEN in the Configuration Word).
Since the time-outs occur from the POR pulse, if the
MCLR/VPP pin is kept low long enough, the time-outs
will expire. Then bringing the MCLR/VPP pin high will
begin execution immediately (Figure 13-14). This is
useful for testing purposes or to synchronize more than
one PIC16CXX device operating in parallel.
Bit1 is POR (Power-on Reset Status bit). It is cleared
on a Power-on Reset and unaffected otherwise. The
user must set this bit following a Power-on Reset.
Table 13-10 and Table 13-11 show the reset conditions
for some special function registers, while Table 13-12
shows the reset conditions for all the registers.
TABLE 13-5: TIME-OUT IN VARIOUS SITUATIONS, PIC16C61/62/64/65
Oscillator Configuration
Power-up
Wake-up from SLEEP
PWRTE = 1
PWRTE = 0
1024TOSC
—
XT, HS, LP
RC
72 ms + 1024TOSC
72 ms
1024 TOSC
—
TABLE 13-6: TIME-OUT IN VARIOUS SITUATIONS,
PIC16C62A/R62/63/R63/64A/R64/65A/R65/66/67
Power-up
Wake up from
SLEEP
Oscillator Configuration
Brown-out
PWRTE = 0
72 ms + 1024TOSC
72 ms
PWRTE = 1
1024TOSC
—
XT, HS, LP
RC
72 ms + 1024TOSC
72 ms
1024 TOSC
—
TABLE 13-7: STATUS BITS AND THEIR SIGNIFICANCE, PIC16C61
TO
PD
1
0
0
1
1
1
0
0
Power-on Reset or MCLR reset during normal operation
WDT Reset
WDT Wake-up
MCLR reset during SLEEP or interrupt wake-up from SLEEP
TABLE 13-8: STATUS BITS AND THEIR SIGNIFICANCE, PIC16C62/64/65
POR
TO
PD
0
0
0
1
1
1
1
1
0
x
0
0
u
1
1
x
0
1
0
u
0
Power-on Reset
Illegal, TO is set on a Power-on Reset
Illegal, PD is set on a Power-on Reset
WDT Reset
WDT Wake-up
MCLR reset during normal operation
MCLR reset during SLEEP or interrupt wake-up from SLEEP
Legend: x= unknown, u= unchanged
DS30234D-page 130
1997 Microchip Technology Inc.
PIC16C6X
TABLE 13-9: STATUS BITS AND THEIR SIGNIFICANCE FOR
PIC16C62A/R62/63/R63/64A/R64/65A/R65/66/67
POR
BOR
TO
PD
0
0
0
1
1
1
1
1
x
x
x
0
1
1
1
1
1
0
x
x
0
0
u
1
1
x
0
x
1
0
u
0
Power-on Reset
Illegal, TO is set on a Power-on Reset
Illegal, PD is set on a Power-on Reset
Brown-out Reset
WDT Reset
WDT Wake-up
MCLR reset during normal operation
MCLR reset during SLEEP or interrupt wake-up from SLEEP
Legend: x= unknown, u= unchanged
TABLE 13-10: RESET CONDITION FOR SPECIAL REGISTERS ON PIC16C61/62/64/65
(2)
Program Counter
000h
STATUS
PCON
Power-on Reset
0001 1xxx
000u uuuu
0001 0uuu
0000 1uuu
uuu0 0uuu
uuu1 0uuu
---- --0-
---- --u-
---- --u-
---- --u-
---- --u-
---- --u-
MCLR reset during normal operation
MCLR reset during SLEEP
WDT Reset
000h
000h
000h
WDT Wake-up
PC + 1
PC + 1(1)
Interrupt wake-up from SLEEP
Legend: u= unchanged, x= unknown, -= unimplemented bit read as '0'.
Note 1: When the wake-up is due to an interrupt and the global enable bit, GIE is set, the PC is loaded with the inter-
rupt vector (0004h) after execution of PC+1.
2: The PCON register is not implemented on the PIC16C61.
TABLE 13-11: RESET CONDITION FOR SPECIAL REGISTERS ON
PIC16C62A/R62/63/R63/64A/R64/65A/R65/66/67
Program Counter
000h
STATUS
PCON
Power-on Reset
0001 1xxx
000u uuuu
0001 0uuu
0000 1uuu
0001 1uuu
uuu0 0uuu
uuu1 0uuu
---- --0x
---- --uu
---- --uu
---- --uu
---- --u0
---- --uu
---- --uu
MCLR reset during normal operation
MCLR reset during SLEEP
WDT Reset
000h
000h
000h
Brown-out Reset
000h
WDT Wake-up
PC + 1
PC + 1(1)
Interrupt wake-up from SLEEP
Legend: u= unchanged, x= unknown, -= unimplemented bit read as '0'.
Note 1: When the wake-up is due to an interrupt and global enable bit, GIE is set, the PC is loaded with the interrupt
vector (0004h) after execution of PC+1.
1997 Microchip Technology Inc.
DS30234D-page 131
PIC16C6X
TABLE 13-12: INITIALIZATION CONDITIONS FOR ALL REGISTERS
Register
Applicable Devices
Power-on Reset MCLR Reset during: Wake-up via
Brown-out
Reset
– normal operation
– SLEEP
interrupt or
WDT Wake-up
WDT Reset
uuuu uuuu
N/A
W
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
xxxx xxxx
N/A
uuuu uuuu
N/A
INDF
TMR0
PCL
xxxx xxxx
0000h
uuuu uuuu
0000h
uuuu uuuu
(2)
PC + 1
(3)
(3)
STATUS
FSR
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
0001 1xxx
000q quuu
uuuq quuu
uuuu uuuu
---u uuuu
--uu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
---- -uuu
---u uuuu
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
xxxx xxxx
---x xxxx
--xx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
---- -xxx
---0 0000
0000 000x
uuuu uuuu
---u uuuu
--uu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
---- -uuu
---0 0000
0000 000u
PORTA
PORTB
PORTC
PORTD
PORTE
PCLATH
INTCON
(1)
uuuu uuuu
uu-- uuuu
uuuu uuuu
---- ---u
(1)
(1)
(2)
PIR1
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
00-- 0000
0000 0000
---- ---0
00-- 0000
0000 0000
---- ---0
PIR2
TMR1L
TMR1H
T1CON
TMR2
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
xxxx xxxx
xxxx xxxx
--00 0000
0000 0000
-000 0000
xxxx xxxx
0000 0000
xxxx xxxx
xxxx xxxx
--00 0000
0000 -00x
0000 0000
0000 0000
xxxx xxxx
xxxx xxxx
0000 0000
1111 1111
---1 1111
--11 1111
1111 1111
uuuu uuuu
uuuu uuuu
--uu uuuu
0000 0000
-000 0000
uuuu uuuu
0000 0000
uuuu uuuu
uuuu uuuu
--00 0000
0000 -00x
0000 0000
0000 0000
uuuu uuuu
uuuu uuuu
0000 0000
1111 1111
---1 1111
--11 1111
1111 1111
uuuu uuuu
uuuu uuuu
--uu uuuu
uuuu uuuu
-uuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
--uu uuuu
uuuu -uuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
---u uuuu
--uu uuuu
uuuu uuuu
T2CON
SSPBUF 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
SSPCON 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
CCPR1L
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
CCPR1H 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
CCP1CON 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
RCSTA
TXREG
RCREG
CCPR2L
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
CCPR2H 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
CCP2CON 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
OPTION
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
TRISA
TRISB
Legend:
u
= unchanged,
x = unknown, -= unimplemented bit read as '0', q = value depends on condition.
Note 1: One or more bits in INTCON, PIR1 and/or PIR2 will be affected (to cause wake-up).
2: When the wake-up is due to an interrupt and the global enable bit, GIE is set, the PC is loaded with the interrupt vector (0004h)
after execution of PC + 1.
3: See Table 13-10 and Table 13-11 for reset value for specific conditions.
DS30234D-page 132
1997 Microchip Technology Inc.
PIC16C6X
TABLE 13-12: INITIALIZATION CONDITIONS FOR ALL REGISTERS (Cont.’d)
Register
Applicable Devices
Power-on Reset MCLR Reset during: Wake-up via
Brown-out
Reset
– normal operation
– SLEEP
interrupt or
WDT Wake-up
WDT Reset
1111 1111
1111 1111
0000 -111
00-- 0000
0000 0000
---- ---0
---- --uu
---- --u-
1111 1111
0000 0000
--00 0000
0000 -010
0000 0000
TRISC
TRISD
TRISE
PIE1
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
1111 1111
1111 1111
0000 -111
00-- 0000
0000 0000
---- ---0
---- --0u
---- --0-
1111 1111
0000 0000
--00 0000
0000 -010
0000 0000
uuuu uuuu
uuuu uuuu
uuuu -uuu
uu-- uuuu
uuuu uuuu
---- ---u
---- --uu
---- --u-
1111 1111
uuuu uuuu
--uu uuuu
uuuu -uuu
uuuu uuuu
PIE2
PCON
PR2
SSPADD 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
SSPSTAT 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
TXSTA
SPBRG
Legend:
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
u
= unchanged,
x = unknown, -= unimplemented bit read as '0', q = value depends on condition.
Note 1: One or more bits in INTCON, PIR1 and/or PIR2 will be affected (to cause wake-up).
2: When the wake-up is due to an interrupt and the global enable bit, GIE is set, the PC is loaded with the interrupt vector (0004h)
after execution of PC + 1.
3: See Table 13-10 and Table 13-11 for reset value for specific conditions.
1997 Microchip Technology Inc.
DS30234D-page 133
PIC16C6X
FIGURE 13-11: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
OST TIME-OUT
TOST
INTERNAL RESET
FIGURE 13-12: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
TOST
OST TIME-OUT
INTERNAL RESET
FIGURE 13-13: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD)
VDD
MCLR
INTERNAL POR
TPWRT
PWRT TIME-OUT
TOST
OST TIME-OUT
INTERNAL RESET
DS30234D-page 134
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 13-14: EXTERNAL POWER-ON
RESET CIRCUIT (FOR SLOW
VDD POWER-UP)
FIGURE 13-15: EXTERNAL BROWN-OUT
PROTECTION CIRCUIT 1
VDD
VDD
VDD
33k
D
R
10k
MCLR
R1
MCLR
40k
PIC16CXX
PIC16CXX
C
Note 1: External Power-on Reset circuit is required
only if VDD power-up slope is too slow.The
diode D helps discharge the capacitor
quickly when VDD powers down.
Note 1: This circuit will activate reset when VDD
goes below (Vz + 0.7V) where Vz = Zener
voltage.
2: Internal brown-out detection on the
PIC16C62A/R62/63/R63/64A/R64/65A/
R65/66/67 should be disabled when using
this circuit.
2: R < 40 kΩ is recommended to make sure
that voltage drop across R does not violate
the devices electrical specifications.
3: R1 = 100Ω to 1 kΩ will limit any current
flowing into MCLR from external capacitor
C in the event of MCLR/VPP pin break-
down due to Electrostatic Discharge
3: Resistors should be adjusted for the
characteristics of the transistors.
(ESD) or Electrostatic Overstress (EOS).
FIGURE 13-16: EXTERNAL BROWN-OUT
PROTECTION CIRCUIT 2
VDD
VDD
R1
R2
Q1
MCLR
40k
PIC16CXX
Note 1: This brown-out circuit is less expensive,
albeit less accurate. Transistor Q1 turns
off when VDD is below a certain level such
that:
R1
= 0.7V
VDD •
R1 + R2
2: Internal brown-out detection on the
PIC16C62A/R62/63/R63/64A/R64/65A/
R65/66/67 should be disabled when using
this circuit.
3: Resistors should be adjusted for the
characteristics of the transistors.
1997 Microchip Technology Inc.
DS30234D-page 135
PIC16C6X
avoid infinite interrupt requests. Individual interrupt flag
bits are set regardless of the status of their correspond-
ing mask bit or the GIE bit.
13.5
Interrupts
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Note: For the PIC16C61/62/64/65, if an interrupt
occurs while the Global Interrupt Enable
bit, GIE is being cleared, bit GIE may unin-
tentionally be re-enabled by the user’s
Interrupt Service Routine (the RETFIE
instruction). The events that would cause
this to occur are:
The PIC16C6X family has up to 11 sources of interrupt.
The interrupt control register (INTCON) records individ-
ual interrupt requests in flag bits. It also has individual
and global interrupt enable bits.
Note: Individual interrupt flag bits are set regard-
less of the status of their corresponding
mask bit or global enable bit, GIE.
1. An instruction clears the GIE bit while
an interrupt is acknowledged
Global interrupt enable bit, GIE (INTCON<7>) enables
(if set) all un-masked interrupts or disables (if cleared)
all interrupts. When bit GIE is enabled, and an interrupt
flag bit and mask bit are set, the interrupt will vector
immediately. Individual interrupts can be disabled
through their corresponding enable bits in the INTCON
register. GIE is cleared on reset.
2. The program branches to the Interrupt
vector and executes the Interrupt Ser-
vice Routine.
3. The Interrupt Service Routine com-
pletes with the execution of the RET-
FIE instruction. This causes the GIE
bit to be set (enables interrupts), and
the program returns to the instruction
after the one which was meant to dis-
able interrupts.
The “return from interrupt” instruction, RETFIE, exits
the interrupt routine as well as sets the GIE bit, which
re-enable interrupts.
The RB0/INT pin interrupt, the RB port change interrupt
and the TMR0 overflow interrupt flag bits are contained
in the INTCON register.
4. Perform the following to ensure that
interrupts are globally disabled.
The peripheral interrupt flag bits are contained in spe-
cial function registers PIR1 and PIR2. The correspond-
ing interrupt enable bits are contained in special
function registers PIE1 and PIE2 and the peripheral
interrupt enable bit is contained in special function reg-
ister INTCON.
LOOP BCF INTCON,GIE
;Disable Global
;Interrupt bit
BTFSC INTCON,GIE ;Global Interrupt
;Disabled?
GOTO LOOP
:
;NO, try again
;Yes, continue
;with program flow
When an interrupt is responded to, bit GIE is cleared to
disable any further interrupts, the return address is
pushed onto the stack and the PC is loaded with
0004h. Once in the interrupt service routine the
source(s) of the interrupt can be determined by polling
the interrupt flag bits. The interrupt flag bit(s) must be
cleared in software before re-enabling interrupts to
avoid recursive interrupts.
For external interrupt events, such as the RB0/INT pin
or RB port change interrupt, the interrupt latency will be
three or four instruction cycles. The exact latency
depends when the interrupt event occurs
(Figure 13-
19). The latency is the same for one or two cycle
instructions. Once in the interrupt service routine the
source(s) of the interrupt can be determined by polling
the interrupt flag bits. The interrupt flag bit(s) must be
cleared in software before re-enabling interrupts to
DS30234D-page 136
1997 Microchip Technology Inc.
PIC16C6X
FIGURE 13-17: INTERRUPT LOGIC FOR PIC16C61
Wake-up
(If in SLEEP mode)
T0IF
T0IE
INTF
INTE
Interrupt to CPU
RBIF
RBIE
GIE
FIGURE 13-18: INTERRUPT LOGIC FOR PIC16C6X
PSPIF
PSPIE
RCIF
RCIE
Wake-up (If in SLEEP mode)
Interrupt to CPU
T0IF
T0IE
INTF
INTE
TXIF
TXIE
RBIF
RBIE
SSPIF
SSPIE
PEIE
GIE
CCP1IF
CCP1IE
TMR2IF
TMR2IE
TMR1IF
TMR1IE
CCP2IF
CCP2IE
The following table shows which devices have which interrupts.
Device
T0IF INTF RBIF PSPIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF CCP2IF
PIC16C62
Yes Yes Yes
-
-
-
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
PIC16C62A Yes Yes Yes
PIC16CR62 Yes Yes Yes
-
-
-
-
PIC16C63
PIC16CR63 Yes Yes Yes
PIC16C64 Yes Yes Yes
PIC16C64A Yes Yes Yes
Yes Yes Yes
-
Yes Yes
Yes Yes
Yes
Yes
-
-
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
-
-
PIC16C64
PIC16C65
Yes Yes Yes
Yes Yes Yes
-
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes
Yes
Yes
Yes
Yes
PIC16C65A Yes Yes Yes
PIC16CR65 Yes Yes Yes
PIC16C66
PIC16C67
Yes Yes Yes
Yes Yes Yes
Yes
1997 Microchip Technology Inc.
DS30234D-page 137
PIC16C6X
13.5.1 INT INTERRUPT
13.5.2 TMR0 INTERRUPT
External interrupt on RB0/INT pin is edge triggered:
either rising if edge select bit INTEDG (OPTION<6>) is
set, or falling, if bit INTEDG is clear. When a valid edge
appears on the RB0/INT pin, flag bit INTF
(INTCON<1>) is set. This interrupt can be disabled by
clearing enable bit INTE (INTCON<4>). The INTF bit
must be cleared in software in the interrupt service rou-
tine before re-enabling this interrupt. The INT interrupt
can wake the processor from SLEEP, if enable bit INTE
was set prior to going into SLEEP. The status of global
enable bit GIE decides whether or not the processor
branches to the interrupt vector following wake-up. See
Section 13.8 for details on SLEEP mode.
An overflow (FFh → 00h) in the TMR0 register will set
flag bit T0IF (INTCON<2>). The interrupt can be
enabled/disabled by setting/clearing enable bit T0IE
(INTCON<5>) (Section 7.0).
13.5.3 PORTB INTERRUPT ON CHANGE
An input change on PORTB<7:4> sets flag bit RBIF
(INTCON<0>). The interrupt can be enabled/disabled
by setting/clearing enable bit RBIE (INTCON<4>)
(Section 5.2).
Note: For the PIC16C61/62/64/65, if a change on
the I/O pin should occur when the read
operation is being executed (start of the Q2
cycle), then flag bit RBIF may not get set.
FIGURE 13-19: INT PIN INTERRUPT TIMING
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
CLKOUT(3)
4
INT pin
1
1
Interrupt Latency (2)
INTF flag
(INTCON<1>)
5
GIE bit
(INTCON<7>)
INSTRUCTION FLOW
PC
PC
PC+1
PC+1
—
0004h
0005h
Instruction
fetched
Inst (PC+1)
Inst (0004h)
Inst (PC)
Inst (0005h)
Inst (0004h)
Instruction
executed
Dummy Cycle
Dummy Cycle
Inst (PC)
Inst (PC-1)
Note 1: INTF flag is sampled here (every Q1).
2: Interrupt latency = 3TCY for synchronous interrupt and 3-4TCY for asynchronous interrupt.
Latency is the same whether Inst (PC) is a single cycle or a 2-cycle instruction.
3: CLKOUT is available only in RC oscillator mode.
4: For minimum width spec of INT pulse, refer to AC specs.
5: INTF can to be set anytime during the Q4-Q1 cycles.
DS30234D-page 138
1997 Microchip Technology Inc.
PIC16C6X
defined in all banks and must be defined at the same
offset from the bank base address (i.e., if W_TEMP is
defined at 0x20 in bank 0, it must also be defined at
0xA0 in bank 1, 0x120 in bank 2, and 0x1A0 in bank 3).
13.6
Context Saving During Interrupts
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
During an interrupt, only the return PC value is saved
on the stack. Typically, users may wish to save key reg-
isters during an interrupt i.e., W register and STATUS
register. This will have to be implemented in software.
The examples:
a) Stores the W register
b) Stores the STATUS register in bank 0
c) Stores PCLATH
Example 13-1 stores and restores the STATUS and W
registers. Example 13-2 stores and restores the
STATUS, W, and PCLATH registers (Devices with
paged program memory). For all PIC16C6X devices
with greater than 1K of program memory (all devices
except PIC16C61), the register, W_TEMP, must be
d) Executes ISR code
e) Restores PCLATH
f) Restores STATUS register (and bank select bit)
g) Restores W register
EXAMPLE 13-1: SAVING STATUS AND W REGISTERS IN RAM (PIC16C61)
MOVWF
SWAPF
MOVWF
:
W_TEMP
STATUS,W
STATUS_TEMP
;Copy W to TEMP register, could be bank one or zero
;Swap status to be saved into W
;Save status to bank zero STATUS_TEMP register
:(ISR)
:
SWAPF
STATUS_TEMP,W
;Swap STATUS_TEMP register into W
;(sets bank to original state)
;Move W into STATUS register
;Swap W_TEMP
MOVWF
SWAPF
SWAPF
STATUS
W_TEMP,F
W_TEMP,W
;Swap W_TEMP into W
EXAMPLE 13-2: SAVING STATUS, W, AND PCLATH REGISTERS IN RAM
(ALL OTHER PIC16C6X DEVICES)
MOVWF
SWAPF
CLRF
MOVWF
MOVF
MOVWF
CLRF
BCF
MOVF
MOVWF
:(ISR)
:
W_TEMP
STATUS,W
STATUS
STATUS_TEMP
PCLATH, W
PCLATH_TEMP
PCLATH
STATUS, IRP
FSR, W
;Copy W to TEMP register, could be bank one or zero
;Swap status to be saved into W
;bank 0, regardless of current bank, Clears IRP,RP1,RP0
;Save status to bank zero STATUS_TEMP register
;Only required if using pages 1, 2 and/or 3
;Save PCLATH into W
;Page zero, regardless of current page
;Return to Bank 0
;Copy FSR to W
FSR_TEMP
;Copy FSR from W to FSR_TEMP
MOVF
MOVWF
SWAPF
PCLATH_TEMP, W
PCLATH
STATUS_TEMP,W
;Restore PCLATH
;Move W into PCLATH
;Swap STATUS_TEMP register into W
;(sets bank to original state)
;Move W into STATUS register
;Swap W_TEMP
MOVWF
SWAPF
SWAPF
STATUS
W_TEMP,F
W_TEMP,W
;Swap W_TEMP into W
1997 Microchip Technology Inc.
DS30234D-page 139
PIC16C6X
assigned to the WDT under software control by writing
to the OPTION register. Thus, time-out periods up to
2.3 seconds can be realized.
13.7
Watchdog Timer (WDT)
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
The CLRWDT and SLEEP instructions clear the WDT
and the postscaler, if assigned to the WDT, and prevent
it from timing out and generating a device RESET con-
dition.
The Watchdog Timer is a free running on-chip RC oscil-
lator which does not require any external components.
This RC oscillator is separate from the RC oscillator of
the OSC1/CLKIN pin. That means that the WDT will
run, even if the clock on the OSC1/CLKIN and OSC2/
CLKOUT pins of the device has been stopped, for
example, by execution of a SLEEP instruction. During
normal operation, a WDT time-out generates a device
reset. If the device is in SLEEP mode, a WDT time-out
causes the device to wake-up and continue with normal
operation (WDT Wake-up). The WDT can be perma-
nently disabled by clearing configuration bit WDTE
(Section 13.1).
The TO bit in the STATUS register will be cleared upon
a WDT time-out.
13.7.2 WDT PROGRAMMING CONSIDERATIONS
It should also be taken in account that under worst case
conditions (VDD = Min., Temperature = Max., max.
WDT prescaler) it may take several seconds before a
WDT time-out occurs.
Note: When a CLRWDT instruction is executed
and the prescaler is assigned to the WDT,
the prescaler count will be cleared, but the
prescaler assignment is not changed.
13.7.1 WDT PERIOD
The WDT has a nominal time-out period of 18 ms, (with
no prescaler). The time-out periods vary with tempera-
DD
ture, V and process variations from part to part (see
DC specs). If longer time-out periods are desired, a
prescaler with a division ratio of up to 1:128 can be
FIGURE 13-20: WATCHDOG TIMER BLOCK DIAGRAM
From TMR0 Clock Source
(see Figure 7-6)
0
Postscaler
8
M
U
X
Watchdog
Timer
1
PS2:PS0
8- to -1 MUX
PSA
WDT
Enable bit
To TMR0 (Figure 7-6)
0
1
MUX
PSA
WDT
Time-out
Note: Bits T0CS, T0SE, PSA, PS2:PS0 are (OPTION<5:0>).
FIGURE 13-21: SUMMARY OF WATCHDOG TIMER REGISTERS
Address Name
Bit 7
Bit 6
Bit 5
CP1
Bit 4
CP0
Bit 3
Bit 2
WDTE FOSC1 FOSC0
PS2 PS1 PS0
Bit 1
Bit 0
(1)
(1)
(1)
2007h
Config. bits
BODEN
PWRTE
PSA
81h,181h OPTION
RBPU
INTEDG
T0CS
T0SE
Legend: Shaded cells are not used by the Watchdog Timer.
Note 1: See Figure 13-1, Figure 13-2, and Figure 13-3 for details of these bits for the specific device.
DS30234D-page 140
1997 Microchip Technology Inc.
PIC16C6X
Other peripherals can not generate interrupts since
during SLEEP, no on-chip Q clocks are present.
13.8
Power-down Mode (SLEEP)
Applicable Devices
When the SLEEPinstruction is being executed, the next
instruction (PC + 1) is pre-fetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be set (enabled). Wake-up is
regardless of the state of the GIE bit. If the GIE bit is
clear (disabled), the device continues execution at the
instruction after the SLEEPinstruction. If the GIE bit is
set (enabled), the device executes the instruction after
the SLEEP instruction and then branches to the inter-
rupt address (0004h). In cases where the execution of
the instruction following SLEEP is not desirable, the
user should have a NOPafter the SLEEPinstruction.
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Power-down mode is entered by executing a SLEEP
instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, status bit PD (STATUS<3>) is cleared,
status bit TO (STATUS<4>) is set, and the oscillator
driver is turned off. The I/O ports maintain the status
they had before the SLEEP instruction was executed
(driving high, low, or hi-impedance).
For lowest current consumption in this mode, place all
I/O pins at either VDD, or VSS, ensure no external cir-
cuitry is drawing current from the I/O pin, and disable
external clocks. Pull all I/O pins, that are hi-impedance
inputs, high or low externally to avoid switching cur-
rents caused by floating inputs.The T0CKI input should
also be at VDD or VSS for lowest current consumption.
The contribution from on-chip pull-ups on PORTB
should be considered.
13.8.2 WAKE-UP USING INTERRUPTS
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
• If the interrupt occurs before the execution of a
SLEEPinstruction, the SLEEPinstruction will com-
plete as a NOP. Therefore, the WDT and WDT
postscaler will not be cleared, the TO bit will not
be set and PD bits will not be cleared.
The MCLR/VPP pin must be at a logic high level
(VIHMC).
13.8.1 WAKE-UP FROM SLEEP
• If the interrupt occurs during or after the execu-
tion of a SLEEPinstruction, the device will imme-
diately wake up from sleep.The SLEEPinstruction
will be completely executed before the wake-up.
Therefore, the WDT and WDT postscaler will be
cleared, the TO bit will be set and the PD bit will
be cleared.
The device can wake from SLEEP through one of the
following events:
1. External reset input on MCLR/VPP pin.
2. Watchdog Timer Wake-up (if WDT was
enabled).
3. Interrupt from RB0/INT pin, RB port change, or
some peripheral interrupts.
Even if the flag bits were checked before executing a
SLEEP instruction, it may be possible for flag bits to
become set before the SLEEPinstruction completes.To
determine whether a SLEEPinstruction executed, test
the PD bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
External MCLR Reset will cause a device reset. All
other events are considered a continuation of program
execution and cause a “wake-up”. The TO and PD bits
in the STATUS register can be used to determine the
cause of device reset. The PD bit, which is set on
power-up is cleared when SLEEPis invoked.The TO bit
is cleared if WDT time-out occurred (and caused wake-
up).
To ensure that the WDT is cleared, a CLRWDTinstruc-
tion should be executed before a SLEEPinstruction.
The following peripheral interrupts can wake the device
from SLEEP:
1. TMR1 interrupt.Timer1 must be operating as an
asynchronous counter.
2. SSP (Start/Stop) bit detect interrupt.
2
3. SSP transmit or receive in slave mode (SPI/I C).
4. CCP capture mode interrupt.
5. Parallel Slave Port read or write.
6. USART TX or RX (synchronous slave mode).
1997 Microchip Technology Inc.
DS30234D-page 141
PIC16C6X
FIGURE 13-22: WAKE-UP FROM SLEEP THROUGH INTERRUPT
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
CLKOUT(4)
INT pin
TOST(2)
INTF flag
(INTCON<1>)
Interrupt Latency
(Note 2)
GIE bit
(INTCON<7>)
Processor in
SLEEP
INSTRUCTION FLOW
PC
PC
PC+1
PC+2
PC+2
PC + 2
0004h
0005h
Instruction
Inst(0004h)
Inst(PC + 1)
Inst(PC + 2)
Inst(0005h)
Inst(PC) = SLEEP
Inst(PC - 1)
fetched
Instruction
executed
Dummy cycle
Dummy cycle
SLEEP
Inst(PC + 1)
Inst(0004h)
Note 1: XT, HS or LP oscillator mode assumed.
2: TOST = 1024TOSC (drawing not to scale) This delay will not be there for RC osc mode.
3: GIE = '1' assumed. In this case after wake-up, the processor jumps to the interrupt routine.
If GIE = '0', execution will continue in-line.
4: CLKOUT is not available in these osc modes, but shown here for timing reference.
The device is placed into a program/verify mode by
holding pins RB6 and RB7 low while raising the MCLR
(VPP) pin from VIL to VIHH (see programming specifica-
tion). RB6 becomes the programming clock and RB7
becomes the programming data. Both RB6 and RB7
are Schmitt Trigger inputs in this mode.
13.9
Program Verification/Code Protection
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
If the code protection bit(s) have not been pro-
grammed, the on-chip program memory can be read
out for verification purposes.
After reset, to place the device in program/verify mode,
the program counter (PC) is at location 00h. A 6-bit
command is then supplied to the device. Depending on
the command, 14-bits of program data are then sup-
plied to or from the device, depending if the command
was a load or a read. For complete details of serial pro-
gramming, please refer to the PIC16C6X/7X Program-
ming Specifications (Literature #DS30228).
Note: Microchip does not recommend code pro-
tecting windowed devices.
13.10 ID Locations
Applicable Devices
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Four memory locations (2000h - 2003h) are designated
as ID locations where the user can store checksum or
other code-identification numbers. These locations are
not accessible during normal execution but are read-
able and writable during program/verify. It is recom-
mended that only the 4 least significant bits of the ID
location are used.
FIGURE 13-23: TYPICAL IN-CIRCUIT SERIAL
PROGRAMMING
CONNECTION
To Normal
Connections
External
Connector
Signals
For ROM devices, these values are submitted along
with the ROM code.
PIC16CXX
+5V
0V
VDD
13.11 In-Circuit Serial Programming
VSS
Applicable Devices
VPP
MCLR/VPP
61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
RB6
RB7
The PIC16CXX microcontrollers can be serially pro-
grammed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground, and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices, and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware or a custom firm-
ware to be programmed.
CLK
Data I/O
VDD
To Normal
Connections
DS30234D-page 142
1997 Microchip Technology Inc.
PIC16C6X
The instruction set is highly orthogonal and is grouped
into three basic categories:
14.0 INSTRUCTION SET SUMMARY
Each PIC16CXX instruction is a 14-bit word divided
into an OPCODE which specifies the instruction type
and one or more operands which further specify the
operation of the instruction. The PIC16CXX instruction
set summary in Table 14-2 lists byte-oriented, bit-ori-
ented, and literal and control operations. Table 14-1
shows the opcode field descriptions.
• Byte-oriented operations
• Bit-oriented operations
• Literal and control operations
All instructions are executed within one single instruc-
tion cycle, unless a conditional test is true or the pro-
gram counter is changed as a result of an instruction.
In this case, the execution takes two instruction cycles
with the second cycle executed as a NOP. One instruc-
tion cycle consists of four oscillator periods. Thus, for
an oscillator frequency of 4 MHz, the normal instruction
execution time is 1 µs. If a conditional test is true or the
program counter is changed as a result of an instruc-
tion, the instruction execution time is 2 µs.
For byte-oriented instructions, 'f' represents a file reg-
ister designator and 'd' represents a destination desig-
nator. The file register designator specifies which file
register is to be used by the instruction.
The destination designator specifies where the result of
the operation is to be placed. If 'd' is zero, the result is
placed in the W register. If 'd' is one, the result is placed
in the file register specified in the instruction.
Table 14-2 lists the instructions recognized by the
MPASM assembler.
For bit-oriented instructions, 'b' represents a bit field
designator which selects the number of the bit affected
by the operation, while 'f' represents the number of the
file in which the bit is located.
Figure 14-1 shows the general formats that the instruc-
tions can have.
Note: To maintain upward compatibility with
future PIC16CXX products, do not use the
OPTIONand TRISinstructions.
For literal and control operations, 'k' represents an
eight or eleven bit constant or literal value.
TABLE 14-1: OPCODE FIELD
DESCRIPTIONS
All examples use the following format to represent a
hexadecimal number:
0xhh
Field
Description
where h signifies a hexadecimal digit.
f
W
b
k
x
Register file address (0x00 to 0x7F)
Working register (accumulator)
FIGURE 14-1: GENERAL FORMAT FOR
INSTRUCTIONS
Bit address within an 8-bit file register
Literal field, constant data or label
Byte-oriented file register operations
13
8
7
6
0
0
Don't care location (= 0 or 1)
The assembler will generate code with x = 0. It is the
recommended form of use for compatibility with all
Microchip software tools.
OPCODE
d
f (FILE #)
d = 0 for destination W
d = 1 for destination f
f = 7-bit file register address
d
Destination select; d = 0: store result in W,
d = 1: store result in file register f.
Default is d = 1
Bit-oriented file register operations
13 10 9
b (BIT #)
label Label name
TOS Top of Stack
PC Program Counter
7
6
OPCODE
f (FILE #)
PCLATH
Program Counter High Latch
b = 3-bit bit address
f = 7-bit file register address
GIE Global Interrupt Enable bit
WDT Watchdog Timer/Counter
TO Time-out bit
Literal and control operations
PD Power-down bit
General
dest Destination either the W register or the specified
13
8
7
0
0
register file location
OPCODE
k (literal)
[ ] Options
Contents
( )
→
k = 8-bit immediate value
Assigned to
Register bit field
In the set of
< >
CALLand GOTOinstructions only
13 11 10
OPCODE
k = 11-bit immediate value
User defined term (font is courier)
italics
k (literal)
1997 Microchip Technology Inc.
DS30234D-page 143
PIC16C6X
TABLE 14-2: PIC16CXX INSTRUCTION SET
Mnemonic,
Operands
Description
Cycles
14-Bit Opcode
Status
Affected
Notes
MSb
LSb
BYTE-ORIENTED FILE REGISTER OPERATIONS
ADDWF
ANDWF
CLRF
CLRW
COMF
DECF
f, d
f, d
f
Add W and f
AND W with f
Clear f
Clear W
Complement f
Decrement f
Decrement f, Skip if 0
Increment f
Increment f, Skip if 0
Inclusive OR W with f
Move f
1
1
1
1
1
1
1(2)
1
1(2)
1
1
1
1
1
1
1
1
1
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
0111 dfff ffff C,DC,Z
1,2
1,2
2
0101 dfff ffff
0001 lfff ffff
0001 0xxx xxxx
1001 dfff ffff
0011 dfff ffff
1011 dfff ffff
1010 dfff ffff
1111 dfff ffff
0100 dfff ffff
1000 dfff ffff
0000 lfff ffff
0000 0xx0 0000
1101 dfff ffff
1100 dfff ffff
Z
Z
Z
Z
Z
-
f, d
f, d
f, d
f, d
f, d
f, d
f, d
f
1,2
1,2
1,2,3
1,2
1,2,3
1,2
DECFSZ
INCF
Z
INCFSZ
IORWF
MOVF
MOVWF
NOP
RLF
RRF
SUBWF
SWAPF
XORWF
Z
Z
1,2
Move W to f
No Operation
-
f, d
f, d
f, d
f, d
f, d
Rotate Left f through Carry
Rotate Right f through Carry
Subtract W from f
Swap nibbles in f
Exclusive OR W with f
C
C
1,2
1,2
1,2
1,2
1,2
0010 dfff ffff C,DC,Z
1110 dfff ffff
0110 dfff ffff Z
BIT-ORIENTED FILE REGISTER OPERATIONS
BCF
BSF
BTFSC
BTFSS
f, b
f, b
f, b
f, b
Bit Clear f
Bit Set f
Bit Test f, Skip if Clear
Bit Test f, Skip if Set
1
1
01
01
00bb bfff ffff
01bb bfff ffff
10bb bfff ffff
11bb bfff ffff
1,2
1,2
3
1 (2) 01
1 (2) 01
3
LITERAL AND CONTROL OPERATIONS
ADDLW
ANDLW
CALL
CLRWDT
GOTO
IORLW
MOVLW
RETFIE
RETLW
RETURN
SLEEP
SUBLW
XORLW
k
k
k
-
k
k
k
-
k
-
-
k
k
Add literal and W
AND literal with W
Call subroutine
Clear Watchdog Timer
Go to address
1
1
2
1
2
1
1
2
2
2
1
1
1
11
11
10
00
10
11
11
00
11
00
00
11
11
111x kkkk kkkk C,DC,Z
1001 kkkk kkkk
0kkk kkkk kkkk
Z
0000 0110 0100 TO,PD
1kkk kkkk kkkk
Inclusive OR literal with W
Move literal to W
1000 kkkk kkkk
00xx kkkk kkkk
0000 0000 1001
01xx kkkk kkkk
0000 0000 1000
Z
Return from interrupt
Return with literal in W
Return from Subroutine
Go into standby mode
Subtract W from literal
Exclusive OR literal with W
0000 0110 0011 TO,PD
110x kkkk kkkk C,DC,Z
1010 kkkk kkkk
Z
Note 1: When an I/O register is modified as a function of itself ( e.g., MOVF PORTB, 1), the value used will be that value present
on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven low by an external
device, the data will be written back with a '0'.
2: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if assigned
to the Timer0 Module.
3: If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is
executed as a NOP.
DS30234D-page 144
1997 Microchip Technology Inc.
PIC16C6X
14.1
Instruction Descriptions
Add Literal and W
ANDLW
AND Literal with W
ADDLW
Syntax:
[label] ANDLW
k
Syntax:
[label] ADDLW
0 ≤ k ≤ 255
k
Operands:
Operation:
Status Affected:
Encoding:
Description:
0 ≤ k ≤ 255
Operands:
Operation:
Status Affected:
Encoding:
Description:
(W) .AND. (k) → (W)
(W) + k → (W)
C, DC, Z
Z
11
1001
kkkk
kkkk
11
111x
kkkk
kkkk
The contents of W register are
AND’ed with the eight bit literal 'k'.The
result is placed in the W register.
The contents of the W register are
added to the eight bit literal 'k' and the
result is placed in the W register.
Words:
1
1
Words:
1
1
Cycles:
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal "k"
Process
data
Write to
W
Decode
Read
literal 'k'
Process
data
Write to
W
ANDLW
0x5F
ADDLW
0x15
Example
Example:
Before Instruction
Before Instruction
W
=
0xA3
0x03
W
=
0x10
0x25
After Instruction
After Instruction
W
=
W
=
ADDWF
Syntax:
Add W and f
ANDWF
Syntax:
AND W with f
[label] ADDWF f,d
[label] ANDWF f,d
Operands:
0 ≤ f ≤ 127
Operands:
0 ≤ f ≤ 127
d
[0,1]
d
[0,1]
Operation:
(W) + (f) → (destination)
Operation:
(W) .AND. (f) → (destination)
Status Affected:
Encoding:
C, DC, Z
Status Affected:
Encoding:
Z
00
0111
dfff
ffff
00
0101
dfff
ffff
Add the contents of the W register with
register 'f'. If 'd' is 0 the result is stored
in the W register. If 'd' is 1 the result is
stored back in register 'f'.
AND the W register with register 'f'. If 'd'
is 0 the result is stored in the W regis-
ter. If 'd' is 1 the result is stored back in
register 'f'.
Description:
Description:
Words:
1
1
Words:
1
1
Cycles:
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register
'f'
Process
data
Write to
destination
Decode
Read
register
'f'
Process
data
Write to
destination
ADDWF
FSR,
0
ANDWF
FSR, 1
Example
Example
Before Instruction
Before Instruction
W
FSR =
=
0x17
0xC2
W
FSR =
=
0x17
0xC2
After Instruction
After Instruction
W
FSR =
=
0xD9
0xC2
W
FSR =
=
0x17
0x02
1997 Microchip Technology Inc.
DS30234D-page 145
PIC16C6X
BCF
Bit Clear f
BTFSC
Bit Test, Skip if Clear
Syntax:
Operands:
[label] BCF f,b
Syntax:
[label] BTFSC f,b
0 ≤ f ≤ 127
0 ≤ b ≤ 7
Operands:
0 ≤ f ≤ 127
0 ≤ b ≤ 7
Operation:
Status Affected:
Encoding:
0 → (f<b>)
Operation:
skip if (f<b>) = 0
None
None
Status Affected:
Encoding:
01
00bb
bfff
ffff
01
10bb
bfff
ffff
If bit 'b' in register 'f' is '1' then the next
instruction is executed.
If bit 'b', in register 'f', is '0' then the next
instruction is discarded, and a NOP is
executed instead, making this a 2TCY
instruction.
Description:
Words:
Bit 'b' in register 'f' is cleared.
Description:
1
1
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register
'f'
Process
data
Write
register 'f'
Words:
1
Cycles:
1(2)
Q Cycle Activity:
Q1
Q2
Q3
Q4
BCF
FLAG_REG, 7
Example
Decode
Read
register 'f'
Process
data
No-
Operation
Before Instruction
FLAG_REG = 0xC7
If Skip:
(2nd Cycle)
After Instruction
FLAG_REG = 0x47
Q1
Q2
Q3
Q4
No-
No-
No-
No-
Operation Operation Operation Operation
HERE
FALSE
TRUE
BTFSC FLAG,1
Example
GOTO
PROCESS_CODE
•
•
•
Before Instruction
PC
=
address HERE
After Instruction
if FLAG<1> = 0,
BSF
Bit Set f
PC =
address TRUE
if FLAG<1>=1,
Syntax:
Operands:
[label] BSF f,b
PC =
address FALSE
0 ≤ f ≤ 127
0 ≤ b ≤ 7
Operation:
Status Affected:
Encoding:
1 → (f<b>)
None
01
01bb
bfff
ffff
Bit 'b' in register 'f' is set.
Description:
Words:
1
1
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register
'f'
Process
data
Write
register 'f'
BSF
FLAG_REG,
7
Example
Before Instruction
FLAG_REG = 0x0A
After Instruction
FLAG_REG = 0x8A
DS30234D-page 146
1997 Microchip Technology Inc.
PIC16C6X
BTFSS
Bit Test f, Skip if Set
CALL
Call Subroutine
Syntax:
[label] BTFSS f,b
Syntax:
[ label ] CALL k
Operands:
0 ≤ f ≤ 127
0 ≤ b < 7
Operands:
Operation:
0 ≤ k ≤ 2047
(PC)+ 1→ TOS,
Operation:
skip if (f<b>) = 1
None
k → PC<10:0>,
(PCLATH<4:3>) → PC<12:11>
Status Affected:
Encoding:
Status Affected: None
01
11bb
bfff
ffff
10
0kkk
kkkk
kkkk
Encoding:
If bit 'b' in register 'f' is '0' then the next
instruction is executed.
If bit 'b' is '1', then the next instruction is
discarded and a NOP is executed
instead, making this a 2TCY instruction.
Description:
Call Subroutine. First, return address
(PC+1) is pushed onto the stack. The
eleven bit immediate address is loaded
into PC bits <10:0>. The upper bits of
the PC are loaded from PCLATH. CALL
is a two cycle instruction.
Description:
Words:
1
Cycles:
1(2)
Words:
1
2
Q Cycle Activity:
Q1
Q2
Q3
Q4
Cycles:
Decode
Read
register 'f'
Process
data
No-
Operation
Q Cycle Activity:
1st Cycle
Q1
Q2
Q3
Q4
Decode
Read
Process
data
Write to
PC
If Skip:
(2nd Cycle)
literal 'k',
Push PC
to Stack
Q1
Q2
Q3
Q4
No-
No-
No-
No-
No-
No-
No-
No-
2nd Cycle
Example
Operation Operation Operation Operation
Operation Operation Operation Operation
HERE
FALSE
TRUE
BTFSC FLAG,1
GOTO
Example
HERE
CALL
THERE
PROCESS_CODE
Before Instruction
•
•
•
PC
=
Address HERE
After Instruction
PC
= Address THERE
Before Instruction
TOS = Address HERE+1
PC
=
address HERE
After Instruction
if FLAG<1> = 0,
PC =
address FALSE
if FLAG<1> = 1,
PC =
address TRUE
1997 Microchip Technology Inc.
DS30234D-page 147
PIC16C6X
CLRF
Clear f
CLRW
Clear W
Syntax:
[label] CLRF
0 ≤ f ≤ 127
f
Syntax:
[ label ] CLRW
None
Operands:
Operation:
Operands:
Operation:
00h → (f)
1 → Z
00h → (W)
1 → Z
Status Affected:
Encoding:
Z
Status Affected:
Encoding:
Z
00
0001
1fff
ffff
00
0001
0xxx
xxxx
The contents of register 'f' are cleared
and the Z bit is set.
Description:
W register is cleared. Zero bit (Z) is
set.
Description:
Words:
1
1
Words:
1
1
Cycles:
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register
'f'
Process
data
Write
register 'f'
Decode
No-
Operation
Process
data
Write to
W
CLRW
Example
CLRF
FLAG_REG
Example
Before Instruction
Before Instruction
FLAG_REG
After Instruction
W
=
0x5A
=
0x5A
After Instruction
W
=
0x00
1
FLAG_REG
Z
=
=
0x00
1
Z
=
CLRWDT
Syntax:
Clear Watchdog Timer
[ label ] CLRWDT
None
Operands:
Operation:
00h → WDT
0 → WDT prescaler,
1 → TO
1 → PD
Status Affected:
Encoding:
TO, PD
00
0000
0110
0100
CLRWDTinstruction resets the Watch-
dog Timer. It also resets the prescaler
of the WDT. Status bits TO and PD are
set.
Description:
Words:
1
1
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
No-
Operation
Process
data
Clear
WDT
Counter
CLRWDT
Example
Before Instruction
After Instruction
WDT counter
=
=
?
WDT counter
0x00
WDT prescaler=
0
1
1
TO
PD
=
=
DS30234D-page 148
1997 Microchip Technology Inc.
PIC16C6X
COMF
Complement f
[ label ] COMF f,d
0 ≤ f ≤ 127
DECFSZ
Syntax:
Decrement f, Skip if 0
Syntax:
Operands:
[ label ] DECFSZ f,d
Operands:
0 ≤ f ≤ 127
d
[0,1]
d
[0,1]
Operation:
(f) → (destination)
Operation:
(f) - 1 → (destination);
skip if result = 0
Status Affected:
Encoding:
Z
Status Affected:
Encoding:
None
00
1001
dfff
ffff
00
1011
dfff
ffff
The contents of register 'f' are comple-
mented. If 'd' is 0 the result is stored in
W. If 'd' is 1 the result is stored back in
register 'f'.
Description:
The contents of register 'f' are decre-
mented. If 'd' is 0 the result is placed in the
W register. If 'd' is 1 the result is placed
back in register 'f'.
If the result is 1, the next instruction, is
executed. If the result is 0, then a NOP is
executed instead making it a 2TCY instruc-
tion.
Description:
Words:
1
1
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register
'f'
Process
data
Write to
destination
Words:
1
Cycles:
1(2)
Q Cycle Activity:
Q1
Q2
Q3
Q4
COMF
REG1,0
Example
Decode
Read
register 'f'
Process
data
Write to
destination
Before Instruction
REG1
After Instruction
REG1
=
0x13
If Skip:
(2nd Cycle)
Q1
Q2
Q3
Q4
=
=
0x13
0xEC
No-
No-
No-
No-
W
Operation Operation Operation Operation
DECF
Decrement f
[label] DECF f,d
0 ≤ f ≤ 127
HERE
DECFSZ
GOTO
CNT, 1
LOOP
Example
Syntax:
Operands:
CONTINUE •
•
•
d
[0,1]
Operation:
(f) - 1 → (destination)
Before Instruction
PC
=
address HERE
Status Affected:
Encoding:
Z
After Instruction
00
0011
dfff
ffff
CNT
if CNT =
PC
if CNT ≠
PC
=
CNT - 1
0,
address CONTINUE
0,
address HERE+1
Decrement register 'f'. If 'd' is 0 the
result is stored in the W register. If 'd' is
1 the result is stored back in register 'f'.
Description:
=
Words:
1
1
=
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register
'f'
Process
data
Write to
destination
DECF
CNT, 1
Example
Before Instruction
CNT
=
0x01
Z
=
0
After Instruction
CNT
Z
=
=
0x00
1
1997 Microchip Technology Inc.
DS30234D-page 149
PIC16C6X
GOTO
Unconditional Branch
INCF
Increment f
Syntax:
[ label ] GOTO k
Syntax:
Operands:
[ label ] INCF f,d
Operands:
Operation:
0 ≤ k ≤ 2047
0 ≤ f ≤ 127
d
[0,1]
k → PC<10:0>
PCLATH<4:3> → PC<12:11>
Operation:
(f) + 1 → (destination)
Status Affected:
Encoding:
None
Status Affected:
Encoding:
Z
10
1kkk
kkkk
kkkk
00
1010
dfff
ffff
GOTOis an unconditional branch. The
eleven bit immediate value is loaded
into PC bits <10:0>. The upper bits of
PC are loaded from PCLATH<4:3>.
GOTOis a two cycle instruction.
The contents of register 'f' are incre-
mented. If 'd' is 0 the result is placed in
the W register. If 'd' is 1 the result is
placed back in register 'f'.
Description:
Description:
Words:
1
1
Words:
1
2
Cycles:
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q Cycle Activity:
1st Cycle
Q1
Q2
Q3
Q4
Decode
Read
register
'f'
Process
data
Write to
destination
Decode
Read
literal 'k'
Process
data
Write to
PC
No-
No-
No-
No-
2nd Cycle
Operation Operation Operation Operation
INCF
CNT, 1
Example
GOTO THERE
Example
Before Instruction
CNT
Z
After Instruction
=
=
0xFF
0
After Instruction
PC
=
Address THERE
CNT
Z
=
=
0x00
1
DS30234D-page 150
1997 Microchip Technology Inc.
PIC16C6X
INCFSZ
Syntax:
Increment f, Skip if 0
[ label ] INCFSZ f,d
0 ≤ f ≤ 127
IORLW
Inclusive OR Literal with W
[ label ] IORLW k
0 ≤ k ≤ 255
Syntax:
Operands:
Operands:
Operation:
Status Affected:
Encoding:
Description:
d
[0,1]
(W) .OR. k → (W)
Z
Operation:
(f) + 1 → (destination),
skip if result = 0
11
1000
kkkk
kkkk
Status Affected:
Encoding:
None
The contents of the W register is
OR’ed with the eight bit literal 'k'. The
result is placed in the W register.
00
1111
dfff
ffff
The contents of register 'f' are incre-
mented. If 'd' is 0 the result is placed in
the W register. If 'd' is 1 the result is
placed back in register 'f'.
If the result is 1, the next instruction is
executed. If the result is 0, a NOP is
executed instead making it a 2TCY
instruction.
Description:
Words:
1
1
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal 'k'
Process
data
Write to
W
Words:
1
Cycles:
1(2)
IORLW
0x35
Example
Q Cycle Activity:
Q1
Q2
Q3
Q4
Before Instruction
Decode
Read
register 'f'
Process
data
Write to
destination
W
=
0x9A
After Instruction
W
Z
=
=
0xBF
1
If Skip:
(2nd Cycle)
Q1
Q2
Q3
Q4
No-
No-
No-
No-
Operation Operation Operation Operation
HERE
INCFSZ
GOTO
CNT, 1
LOOP
Example
CONTINUE •
•
•
Before Instruction
PC
=
address HERE
After Instruction
CNT
=
CNT + 1
if CNT=
0,
PC
if CNT≠
=
address CONTINUE
0,
PC
=
address HERE +1
1997 Microchip Technology Inc.
DS30234D-page 151
PIC16C6X
IORWF
Inclusive OR W with f
MOVLW
Move Literal to W
[ label ] MOVLW k
0 ≤ k ≤ 255
Syntax:
[ label ] IORWF f,d
Syntax:
Operands:
0 ≤ f ≤ 127
Operands:
Operation:
Status Affected:
Encoding:
Description:
d
[0,1]
k → (W)
Operation:
(W) .OR. (f) → (destination)
None
Status Affected:
Encoding:
Z
11
00xx
kkkk
kkkk
00
0100
dfff
ffff
The eight bit literal 'k' is loaded into W
register. The don’t cares will assemble
as 0’s.
Inclusive OR the W register with regis-
ter 'f'. If 'd' is 0 the result is placed in the
W register. If 'd' is 1 the result is placed
back in register 'f'.
Description:
Words:
1
1
Words:
1
1
Cycles:
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
literal 'k'
Process
data
Write to
W
Decode
Read
register
'f'
Process
data
Write to
destination
MOVLW
0x5A
Example
After Instruction
IORWF
RESULT, 0
Example
W
=
0x5A
Before Instruction
RESULT =
0x13
0x91
W
=
After Instruction
RESULT =
0x13
0x93
1
W
Z
=
=
MOVF
Move f
MOVWF
Move W to f
Syntax:
Operands:
[ label ] MOVF f,d
Syntax:
[ label ] MOVWF
0 ≤ f ≤ 127
(W) → (f)
f
0 ≤ f ≤ 127
Operands:
Operation:
Status Affected:
Encoding:
Description:
d
[0,1]
Operation:
(f) → (destination)
None
Status Affected:
Encoding:
Z
00
0000
1fff
ffff
00
1000
dfff
ffff
Move data from W register to register
'f'.
The contents of register f is moved to a
destination dependant upon the status
of d. If d = 0, destination is W register. If
d = 1, the destination is file register f
itself. d = 1 is useful to test a file regis-
ter since status flag Z is affected.
Description:
Words:
1
1
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register
'f'
Process
data
Write
register 'f'
Words:
1
1
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
MOVWF
OPTION_REG
Example
Decode
Read
register
'f'
Process
data
Write to
destination
Before Instruction
OPTION =
0xFF
0x4F
W
=
After Instruction
MOVF
FSR, 0
Example
OPTION =
0x4F
0x4F
After Instruction
W
=
W = value in FSR register
Z
= 1
DS30234D-page 152
1997 Microchip Technology Inc.
PIC16C6X
NOP
No Operation
[ label ] NOP
None
RETFIE
Return from Interrupt
Syntax:
Syntax:
[ label ] RETFIE
None
Operands:
Operation:
Status Affected:
Encoding:
Description:
Words:
Operands:
Operation:
No operation
None
TOS → PC,
1 → GIE
Status Affected:
Encoding:
None
00
0000
0xx0
0000
00
0000
0000
1001
No operation.
Return from Interrupt. Stack is POPed
and Top of Stack (TOS) is loaded in the
PC. Interrupts are enabled by setting
Global Interrupt Enable bit, GIE
(INTCON<7>). This is a two cycle
instruction.
Description:
1
1
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
No-
No-
No-
Operation Operation Operation
Words:
1
2
Cycles:
NOP
Example
Q Cycle Activity:
1st Cycle
Q1
Q2
Q3
Q4
Decode
No-
Set the
Pop from
the Stack
Operation GIE bit
No-
No- No-
No-
2nd Cycle
Operation Operation Operation Operation
RETFIE
Example
After Interrupt
PC
GIE =
=
TOS
1
OPTION
Syntax:
Load Option Register
[ label ] OPTION
None
Operands:
Operation:
(W) → OPTION
Status Affected: None
00
0000
0110
0010
Encoding:
The contents of the W register are
loaded in the OPTION register. This
instruction is supported for code com-
patibility with PIC16C5X products.
Since OPTION is a readable/writable
register, the user can directly address
it.
Description:
Words:
Cycles:
Example
1
1
To maintain upward compatibility
with future PIC16CXX products, do
not use this instruction.
1997 Microchip Technology Inc.
DS30234D-page 153
PIC16C6X
RETLW
Return with Literal in W
RETURN
Return from Subroutine
[ label ] RETURN
None
Syntax:
[ label ] RETLW k
Syntax:
Operands:
Operation:
0 ≤ k ≤ 255
Operands:
Operation:
Status Affected:
Encoding:
Description:
k → (W);
TOS → PC
TOS → PC
None
Status Affected:
Encoding:
None
00
0000
0000
1000
11
01xx
kkkk
kkkk
Return from subroutine. The stack is
POPed and the top of the stack (TOS)
is loaded into the program counter.This
is a two cycle instruction.
The W register is loaded with the eight
bit literal 'k'. The program counter is
loaded from the top of the stack (the
return address). This is a two cycle
instruction.
Description:
Words:
1
2
Cycles:
Words:
1
2
Q Cycle Activity:
1st Cycle
Q1
Q2
Q3
Q4
Cycles:
Decode
No-
No-
Pop from
Q Cycle Activity:
1st Cycle
Q1
Q2
Q3
Q4
Operation Operation the Stack
Decode
Read
No-
WritetoW,
No-
No- No- No-
2nd Cycle
literal 'k' Operation Pop from
the Stack
Operation Operation Operation Operation
No-
No-
No-
No-
2nd Cycle
Example
RETURN
Example
Operation Operation Operation Operation
After Interrupt
PC
=
TOS
CALL TABLE ;W contains table
;offset value
•
;W now has table value
•
•
TABLE
ADDWF PC
RETLW k1
RETLW k2
•
;W = offset
;Begin table
;
•
•
RETLW kn
; End of table
Before Instruction
W
=
0x07
After Instruction
W
=
value of k8
DS30234D-page 154
1997 Microchip Technology Inc.
PIC16C6X
RLF
Rotate Left f through Carry
RRF
Rotate Right f through Carry
[ label ] RRF f,d
0 ≤ f ≤ 127
Syntax:
Operands:
[ label ]
RLF f,d
Syntax:
Operands:
0 ≤ f ≤ 127
d
[0,1]
d
[0,1]
Operation:
See description below
C
Operation:
See description below
C
Status Affected:
Encoding:
Status Affected:
Encoding:
00
1101
dfff
ffff
00
1100
dfff
ffff
The contents of register 'f' are rotated
one bit to the left through the Carry
Flag. If 'd' is 0 the result is placed in the
W register. If 'd' is 1 the result is stored
back in register 'f'.
The contents of register 'f' are rotated
one bit to the right through the Carry
Flag. If 'd' is 0 the result is placed in the
W register. If 'd' is 1 the result is placed
back in register 'f'.
Description:
Description:
C
Register f
C
Register f
Words:
1
1
Words:
1
1
Cycles:
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register
'f'
Process
data
Write to
destination
Decode
Read
register
'f'
Process
data
Write to
destination
RLF
REG1,0
Example
RRF
REG1,0
Example
Before Instruction
Before Instruction
REG1
C
=
=
1110 0110
0
REG1
C
=
=
1110 0110
0
After Instruction
After Instruction
REG1
W
C
=
=
=
1110 0110
1100 1100
1
REG1
W
C
=
=
=
1110 0110
0111 0011
0
1997 Microchip Technology Inc.
DS30234D-page 155
PIC16C6X
SLEEP
SUBLW
Subtract W from Literal
Syntax:
[ label ]
SUBLW k
Syntax:
[ label ] SLEEP
Operands:
Operation:
0 ≤ k ≤ 255
Operands:
Operation:
None
k - (W) → (W)
00h → WDT,
0 → WDT prescaler,
1 → TO,
Status Affected: C, DC, Z
Encoding:
11
110x
kkkk
kkkk
0 → PD
The W register is subtracted (2’s comple-
ment method) from the eight bit literal 'k'.
The result is placed in the W register.
Description:
Status Affected:
Encoding:
TO, PD
00
0000
0110
0011
Words:
1
1
The power-down status bit, PD is
cleared. Time-out status bit, TO is
set. Watchdog Timer and its pres-
caler are cleared.
Description:
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
The processor is put into SLEEP
mode with the oscillator stopped. See
Section 13.8 for more details.
Decode
Read
literal 'k'
Process Write to W
data
Words:
1
1
Example 1:
SUBLW
0x02
Cycles:
Before Instruction
Q Cycle Activity:
Q1
Q2
Q3
Q4
W
C
Z
=
=
=
1
?
?
Decode
No-
No-
Go to
Operation Operation Sleep
After Instruction
Example:
SLEEP
W
C
Z
=
=
=
1
1; result is positive
0
Example 2:
Before Instruction
W
C
Z
=
=
=
2
?
?
After Instruction
W
C
Z
=
=
=
0
1; result is zero
1
Example 3:
Before Instruction
W
C
Z
=
=
=
3
?
?
After Instruction
W
C
Z
=
=
=
0xFF
0; result is negative
0
DS30234D-page 156
1997 Microchip Technology Inc.
PIC16C6X
SUBWF
Syntax:
Subtract W from f
SWAPF
Syntax:
Swap Nibbles in f
[ label ] SWAPF f,d
[ label ]
SUBWF f,d
Operands:
0 ≤ f ≤ 127
Operands:
0 ≤ f ≤ 127
d
[0,1]
d
[0,1]
Operation:
(f<3:0>) → (destination<7:4>),
(f<7:4>) → (destination<3:0>)
Operation:
(f) - (W) → (destination)
Status Affected: C, DC, Z
Status Affected:
Encoding:
None
Encoding:
00
0010
dfff
ffff
00
1110
dfff
ffff
Subtract (2’s complement method) W reg-
ister from register 'f'. If 'd' is 0 the result is
stored in the W register. If 'd' is 1 the
result is stored back in register 'f'.
Description:
The upper and lower nibbles of register
'f' are exchanged. If 'd' is 0 the result is
placed in W register. If 'd' is 1 the result
is placed in register 'f'.
Description:
Words:
1
1
Words:
1
1
Cycles:
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
register 'f'
Process
data
Write to
destination
Decode
Read
register 'f'
Process
data
Write to
destination
Example 1:
SUBWF
REG1,1
SWAPF REG,
0
Example
Before Instruction
Before Instruction
REG1
REG1
=
=
=
=
3
2
?
?
W
C
Z
=
0xA5
After Instruction
REG1
W
=
=
0xA5
0x5A
After Instruction
REG1
=
1
2
W
C
Z
=
=
=
1; result is positive
0
Example 2:
Before Instruction
TRIS
Load TRIS Register
REG1
=
=
=
=
2
2
?
?
Syntax:
[label] TRIS
f
W
C
Z
Operands:
Operation:
5 ≤ f ≤ 7
(W) → TRIS register f;
Status Affected: None
After Instruction
00
Encoding:
0000 0110
0fff
REG1
=
0
W
C
Z
=
=
=
2
The instruction is supported for code
compatibility with the PIC16C5X prod-
ucts. Since TRIS registers are read-
able and writable, the user can directly
address them.
Description:
1; result is zero
1
Example 3:
Before Instruction
REG1
=
=
=
=
1
2
?
?
Words:
Cycles:
Example
1
1
W
C
Z
After Instruction
To maintain upward compatibility
with future PIC16CXX products, do
not use this instruction.
REG1
=
0xFF
2
0; result is negative
0
W
C
Z
=
=
=
1997 Microchip Technology Inc.
DS30234D-page 157
PIC16C6X
XORLW
Exclusive OR Literal with W
[label] XORLW k
XORWF
Syntax:
Exclusive OR W with f
[label] XORWF f,d
0 ≤ f ≤ 127
Syntax:
Operands:
Operands:
Operation:
Status Affected:
Encoding:
0 ≤ k ≤ 255
d
[0,1]
(W) .XOR. k → (W)
Operation:
(W) .XOR. (f) → (destination)
Z
Status Affected:
Encoding:
Z
11
1010 kkkk kkkk
00
0110
dfff
ffff
The contents of the W register are
XOR’ed with the eight bit literal 'k'.
The result is placed in the W regis-
ter.
Description:
Exclusive OR the contents of the W
register with register 'f'. If 'd' is 0 the
result is stored in the W register. If 'd' is
1 the result is stored back in register 'f'.
Description:
Words:
1
1
Words:
1
1
Cycles:
Cycles:
Q Cycle Activity:
Q1
Q2
Q3
Q4
Q Cycle Activity:
Q1
Q2
Q3
Q4
Decode
Read
Process Write to
literal 'k'
data
W
Decode
Read
register
'f'
Process
data
Write to
destination
Example:
XORLW 0xAF
Before Instruction
REG
1
Example
XORWF
W
=
0xB5
0x1A
Before Instruction
After Instruction
REG
W
=
=
0xAF
0xB5
W
=
After Instruction
REG
W
=
=
0x1A
0xB5
DS30234D-page 158
1997 Microchip Technology Inc.
PIC16C6X
15.3
ICEPIC: Low-cost PIC16CXXX
In-Circuit Emulator
15.0 DEVELOPMENT SUPPORT
15.1
Development Tools
ICEPIC is a low-cost in-circuit emulator solution for the
Microchip PIC16C5X and PIC16CXXX families of 8-bit
OTP microcontrollers.
The PIC16/17 microcontrollers are supported with a full
range of hardware and software development tools:
• PICMASTER/PICMASTER CE Real-Time
In-Circuit Emulator
ICEPIC is designed to operate on PC-compatible
machines ranging from 286-AT through Pentium
based machines under Windows 3.x environment.
ICEPIC features real time, non-intrusive emulation.
• ICEPIC Low-Cost PIC16C5X and PIC16CXXX
In-Circuit Emulator
• PRO MATE II Universal Programmer
15.4
PRO MATE II: Universal Programmer
• PICSTART Plus Entry-Level Prototype
Programmer
The PRO MATE II Universal Programmer is a full-fea-
tured programmer capable of operating in stand-alone
mode as well as PC-hosted mode.
• PICDEM-1 Low-Cost Demonstration Board
• PICDEM-2 Low-Cost Demonstration Board
• PICDEM-3 Low-Cost Demonstration Board
• MPASM Assembler
The PRO MATE II has programmable VDD and VPP
supplies which allows it to verify programmed memory
at VDD min and VDD max for maximum reliability. It has
an LCD display for displaying error messages, keys to
enter commands and a modular detachable socket
assembly to support various package types. In stand-
alone mode the PRO MATE II can read, verify or pro-
gram PIC16C5X, PIC16CXXX, PIC17CXX and
PIC14000 devices. It can also set configuration and
code-protect bits in this mode.
• MPLAB-SIM Software Simulator
• MPLAB-C (C Compiler)
• Fuzzy logic development system (fuzzyTECH −MP)
15.2
PICMASTER: High Performance
Universal In-Circuit Emulator with
MPLAB IDE
The PICMASTER Universal In-Circuit Emulator is
intended to provide the product development engineer
with a complete microcontroller design tool set for all
microcontrollers in the PIC12C5XX, PIC14C000,
PIC16C5X, PIC16CXXX and PIC17CXX families.
PICMASTER is supplied with the MPLAB Integrated
Development Environment (IDE), which allows editing,
“make” and download, and source debugging from a
single environment.
15.5
PICSTART Plus Entry Level
Development System
The PICSTART programmer is an easy-to-use, low-
cost prototype programmer. It connects to the PC via
one of the COM (RS-232) ports. MPLAB Integrated
Development Environment software makes using the
programmer simple and efficient. PICSTART Plus is
not recommended for production programming.
Interchangeable target probes allow the system to be
easily reconfigured for emulation of different proces-
sors. The universal architecture of the PICMASTER
allows expansion to support all new Microchip micro-
controllers.
PICSTART Plus supports all PIC12C5XX, PIC14000,
PIC16C5X, PIC16CXXX and PIC17CXX devices with
up to 40 pins. Larger pin count devices such as the
PIC16C923 and PIC16C924 may be supported with an
adapter socket.
The PICMASTER Emulator System has been
designed as
a real-time emulation system with
advanced features that are generally found on more
expensive development tools. The PC compatible 386
(and higher) machine platform and Microsoft Windows
3.x environment were chosen to best make these fea-
tures available to you, the end user.
A CE compliant version of PICMASTER is available for
European Union (EU) countries.
1997 Microchip Technology Inc.
DS30234D-page 159
PIC16C6X
an RS-232 interface, push-button switches, a potenti-
ometer for simulated analog input, a thermistor and
separate headers for connection to an external LCD
module and a keypad. Also provided on the PICDEM-3
board is an LCD panel, with 4 commons and 12 seg-
ments, that is capable of displaying time, temperature
and day of the week. The PICDEM-3 provides an addi-
tional RS-232 interface and Windows 3.1 software for
showing the demultiplexed LCD signals on a PC. A sim-
ple serial interface allows the user to construct a hard-
ware demultiplexer for the LCD signals.
15.6
PICDEM-1 Low-Cost PIC16/17
Demonstration Board
The PICDEM-1 is a simple board which demonstrates
the capabilities of several of Microchip’s microcontrol-
lers. The microcontrollers supported are: PIC16C5X
(PIC16C54 to PIC16C58A), PIC16C61, PIC16C62X,
PIC16C71, PIC16C8X, PIC17C42, PIC17C43 and
PIC17C44. All necessary hardware and software is
included to run basic demo programs. The users can
program the sample microcontrollers provided with
the PICDEM-1 board, on
a PRO MATE II or
15.9
MPLAB Integrated Development
Environment Software
PICSTART-16B programmer, and easily test firm-
ware. The user can also connect the PICDEM-1
board to the PICMASTER emulator and download
the firmware to the emulator for testing. Additional pro-
totype area is available for the user to build some addi-
tional hardware and connect it to the microcontroller
socket(s). Some of the features include an RS-232
interface, a potentiometer for simulated analog input,
push-button switches and eight LEDs connected to
PORTB.
The MPLAB IDE Software brings an ease of software
development previously unseen in the 8-bit microcon-
troller market. MPLAB is a windows based application
which contains:
• A full featured editor
• Three operating modes
- editor
- emulator
- simulator
• A project manager
• Customizable tool bar and key mapping
• A status bar with project information
• Extensive on-line help
15.7
PICDEM-2 Low-Cost PIC16CXX
Demonstration Board
The PICDEM-2 is a simple demonstration board that
supports the PIC16C62, PIC16C64, PIC16C65,
PIC16C73 and PIC16C74 microcontrollers. All the
necessary hardware and software is included to
run the basic demonstration programs. The user
can program the sample microcontrollers provided
with the PICDEM-2 board, on a PRO MATE II pro-
grammer or PICSTART-16C, and easily test firmware.
The PICMASTER emulator may also be used with the
PICDEM-2 board to test firmware. Additional prototype
area has been provided to the user for adding addi-
tional hardware and connecting it to the microcontroller
socket(s). Some of the features include a RS-232 inter-
face, push-button switches, a potentiometer for simu-
lated analog input, a Serial EEPROM to demonstrate
MPLAB allows you to:
• Edit your source files (either assembly or ‘C’)
• One touch assemble (or compile) and download
to PIC16/17 tools (automatically updates all
project information)
• Debug using:
- source files
- absolute listing file
• Transfer data dynamically via DDE (soon to be
replaced by OLE)
• Run up to four emulators on the same PC
The ability to use MPLAB with Microchip’s simulator
allows a consistent platform and the ability to easily
switch from the low cost simulator to the full featured
emulator with minimal retraining due to development
tools.
2
usage of the I C bus and separate headers for connec-
tion to an LCD module and a keypad.
15.8
PICDEM-3 Low-Cost PIC16CXXX
Demonstration Board
15.10 Assembler (MPASM)
The PICDEM-3 is a simple demonstration board that
supports the PIC16C923 and PIC16C924 in the PLCC
package. It will also support future 44-pin PLCC
microcontrollers with a LCD Module. All the neces-
sary hardware and software is included to run the
basic demonstration programs. The user can pro-
gram the sample microcontrollers provided with
the PICDEM-3 board, on a PRO MATE II program-
mer or PICSTART Plus with an adapter socket, and
easily test firmware. The PICMASTER emulator may
also be used with the PICDEM-3 board to test firmware.
Additional prototype area has been provided to the
user for adding hardware and connecting it to the
microcontroller socket(s). Some of the features include
The MPASM Universal Macro Assembler is a PC-
hosted symbolic assembler. It supports all microcon-
troller series including the PIC12C5XX, PIC14000,
PIC16C5X, PIC16CXXX, and PIC17CXX families.
MPASM offers full featured Macro capabilities, condi-
tional assembly, and several source and listing formats.
It generates various object code formats to support
Microchip's development tools as well as third party
programmers.
MPASM allows full symbolic debugging from
PICMASTER, Microchip’s Universal Emulator
System.
DS30234D-page 160
1997 Microchip Technology Inc.
PIC16C6X
MPASM has the following features to assist in develop-
ing software for specific use applications.
15.14 MP-DriveWay – Application Code
Generator
• Provides translation of Assembler source code to
object code for all Microchip microcontrollers.
MP-DriveWay is an easy-to-use Windows-based Appli-
cation Code Generator. With MP-DriveWay you can
visually configure all the peripherals in a PIC16/17
device and, with a click of the mouse, generate all the
initialization and many functional code modules in C
language. The output is fully compatible with Micro-
chip’s MPLAB-C C compiler. The code produced is
highly modular and allows easy integration of your own
code. MP-DriveWay is intelligent enough to maintain
your code through subsequent code generation.
• Macro assembly capability.
• Produces all the files (Object, Listing, Symbol,
and special) required for symbolic debug with
Microchip’s emulator systems.
• Supports Hex (default), Decimal and Octal source
and listing formats.
MPASM provides a rich directive language to support
programming of the PIC16/17. Directives are helpful in
making the development of your assemble source code
shorter and more maintainable.
15.15 SEEVAL Evaluation and
Programming System
15.11 Software Simulator (MPLAB-SIM)
The SEEVAL SEEPROM Designer’s Kit supports all
Microchip 2-wire and 3-wire Serial EEPROMs. The kit
includes everything necessary to read, write, erase or
program special features of any Microchip SEEPROM
product including Smart Serials and secure serials.
The Total Endurance Disk is included to aid in trade-
off analysis and reliability calculations. The total kit can
significantly reduce time-to-market and result in an
optimized system.
The MPLAB-SIM Software Simulator allows code
development in a PC host environment. It allows the
user to simulate the PIC16/17 series microcontrollers
on an instruction level. On any given instruction, the
user may examine or modify any of the data areas or
provide external stimulus to any of the pins. The input/
output radix can be set by the user and the execution
can be performed in; single step, execute until break, or
in a trace mode.
15.16 TrueGauge Intelligent Battery
Management
MPLAB-SIM fully supports symbolic debugging using
MPLAB-C and MPASM. The Software Simulator offers
the low cost flexibility to develop and debug code out-
side of the laboratory environment making it an excel-
lent multi-project software development tool.
The TrueGauge development tool supports system
development with the MTA11200B TrueGauge Intelli-
gent Battery Management IC. System design verifica-
tion can be accomplished before hardware prototypes
are built. User interface is graphically-oriented and
measured data can be saved in a file for exporting to
Microsoft Excel.
15.12 C Compiler (MPLAB-C)
The MPLAB-C Code Development System is a
complete ‘C’ compiler and integrated development
environment for Microchip’s PIC16/17 family of micro-
controllers. The compiler provides powerful integration
capabilities and ease of use not found with other
compilers.
15.17 KEELOQ Evaluation and
Programming Tools
KEELOQ evaluation and programming tools support
Microchips HCS Secure Data Products. The HCS eval-
uation kit includes an LCD display to show changing
codes, a decoder to decode transmissions, and a pro-
gramming interface to program test transmitters.
For easier source level debugging, the compiler pro-
vides symbol information that is compatible with the
MPLAB IDE memory display (PICMASTER emulator
software versions 1.13 and later).
15.13 Fuzzy Logic Development System
(fuzzyTECH-MP)
fuzzyTECH-MP fuzzy logic development tool is avail-
able in two versions - a low cost introductory version,
MP Explorer, for designers to gain a comprehensive
working knowledge of fuzzy logic system design; and a
full-featured version, fuzzyTECH-MP, edition for imple-
menting more complex systems.
Both versions include Microchip’s fuzzyLAB demon-
stration board for hands-on experience with fuzzy logic
systems implementation.
1997 Microchip Technology Inc.
DS30234D-page 161
PIC16C6X
TABLE 15-1: DEVELOPMENT TOOLS FROM MICROCHIP
ufzy
D e m o B o a r d s
E m u l a t o r P r o d u c t s
S o f t w a r e T o o l s
P r o g r a m m e r s
DS30234D-page 162
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
16.0 ELECTRICAL CHARACTERISTICS FOR PIC16C61
Absolute Maximum Ratings †
Ambient temperature under bias..............................................................................................................-55˚C to +125˚C
Storage temperature............................................................................................................................... -65˚C to +150˚C
Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4) ..........................................-0.3V to (VDD + 0.3V)
Voltage on VDD with respect to VSS .......................................................................................................... -0.3V to +7.5V
Voltage on MCLR with respect to VSS (Note 2) ..............................................................................................0V to +14V
Voltage on RA4 pin with respect to Vss ...........................................................................................................0V to +14V
Total power dissipation (Note 1)............................................................................................................................800 mW
Maximum current out of VSS pin ............................................................................................................................150 mA
Maximum current into VDD pin...............................................................................................................................100 mA
Input clamp current, IIK (VI < 0 or VI > VDD) .....................................................................................................................±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD)..............................................................................................................±20 mA
Maximum output current sunk by any I/O pin...........................................................................................................25 mA
Maximum output current sourced by any I/O pin .....................................................................................................20 mA
Maximum current sunk by PORTA ...........................................................................................................................80 mA
Maximum current sourced by PORTA......................................................................................................................50 mA
Maximum current sunk by PORTB.........................................................................................................................150 mA
Maximum current sourced by PORTB ...................................................................................................................100 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOl x IOL)
Note 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up.Thus,
a series resistor of 50-100Ω should be used when applying a “low” level to the MCLRpin rather than pulling
this pin directly to VSS.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 16-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
OSC
PIC16C61-04
PIC16C61-20
PIC16LC61-04
VDD: 3.0V to 6.0V
JW Devices
RC
VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.0V to 6.0V
IDD: 3.3 mA max. at 5.5V
IPD: 14 µA max. at 4V
Freq: 4 MHz max.
IDD: 1.8 mA typ. at 5.5V IDD: 1.4 mA typ. at 3.0V
IDD: 3.3 mA max. at 5.5V
IPD: 14 µA max. at 4V
Freq: 4 MHz max.
IPD: 1.0 µA typ. at 4V
IPD: 0.6 µA typ. at 3V
Freq: 4 MHz max.
Freq: 4 MHz max.
XT
HS
VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
IDD: 1.8 mA typ. at 5.5V IDD: 1.4 mA typ. at 3.0V
IPD: 1.0 µA typ. at 4V
Freq: 4 MHz max.
VDD: 3.0V to 6.0V
VDD: 4.0V to 6.0V
IDD: 3.3 mA max. at 5.5V
IPD: 14 µA max. at 4V
Freq: 4 MHz max.
IDD: 3.3 mA max. at 5.5V
IPD: 14 µA max. at 4V
Freq: 4 MHz max.
IPD: 0.6 µA typ. at 3V
Freq: 4 MHz max.
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 13.5 mA typ. at 5.5V
IPD: 1.0 µA typ. at 4.5V
Freq: 4 MHz max.
IDD: 30 mA max. at 5.5V
IPD: 1.0 µA typ. at 4.5V
Freq: 20 MHz max.
IDD: 30 mA max. at 5.5V
IPD: 1.0 µA typ. at 4.5V
Freq: 20 MHz max.
Not recommended for use in
HS mode
LP
VDD: 4.0V to 6.0V
IDD: 15 µA typ. at 32 kHz,
4.0V
IPD: 0.6 µA typ. at 4.0V
Freq: 200 kHz max.
VDD: 3.0V to 6.0V
IDD: 32 µA max. at 32 kHz, IDD: 32 µA max. at 32 kHz,
VDD: 3.0V to 6.0V
Not recommended for
use in LP mode
3.0V
3.0V
IPD: 9 µA max. at 3.0V
Freq: 200 kHz max.
IPD: 9 µA max. at 3.0V
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifications.
It is recommended that the user select the device type that ensures the specifications required.
1997 Microchip Technology Inc.
DS30234D-page 163
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
16.1
DC Characteristics:
PIC16C61-04 (Commercial, Industrial, Extended)
PIC16C61-20 (Commercial, Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40˚C ≤ TA ≤ +125˚C for extended,
DC CHARACTERISTICS
-40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym
VDD
Min Typ† Max Units
Conditions
D001
D001A
Supply Voltage
4.0
4.5
-
-
6.0
5.5
V
V
XT, RC and LP osc configuration
HS osc configuration
D002*
RAM Data Retention
Voltage (Note 1)
VDR
-
1.5
-
V
D003
VDD start voltage to
ensure internal Power-
on Reset signal
VPOR
-
VSS
-
V
See section on Power-on Reset for details
D004*
VDD rise rate to ensure SVDD
internal Power-on
0.05
-
-
V/ms See section on Power-on Reset for details
Reset signal
D010
D013
Supply Current (Note 2) IDD
-
-
1.8 3.3 mA FOSC = 4 MHz, VDD = 5.5V (Note 4)
13.5 30
mA HS osc configuration
FOSC = 20 MHz, VDD = 5.5V
D020
D021
D021A
D021B
Power-down Current
(Note 3)
IPD
-
-
-
-
7
28
14
16
20
µA VDD = 4.0V, WDT enabled, -40°C to +85°C
µA VDD = 4.0V, WDT disabled, -0°C to +70°C
µA VDD = 4.0V, WDT disabled, -40°C to +85°C
µA VDD = 4.0V, WDT disabled, -40°C to +125°C
1.0
1.0
1.0
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
DS30234D-page 164
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
16.2
DC Characteristics:
PIC16LC61-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature -40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym Min Typ† Max Units
Conditions
D001
Supply Voltage
VDD
3.0
-
-
6.0
-
V
V
XT, RC, and LP osc configuration
D002* RAM Data Retention Volt- VDR
age (Note 1)
1.5
D003
VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
SVDD
IDD
-
VSS
-
-
-
V
See section on Power-on Reset for details
D004* VDD rise rate to ensure
internal Power-on Reset
signal
0.05
V/ms See section on Power-on Reset for details
mA FOSC = 4 MHz, VDD = 3.0V (Note 4)
D010
Supply Current (Note 2)
-
-
1.4
15
2.5
32
D010A
µA FOSC = 32 kHz, VDD = 3.0V, WDT disabled,
LP osc configuration
D020
D021
D021A
Power-down Current
(Note 3)
IPD
-
-
-
5
0.6
0.6
20
9
12
µA VDD = 3.0V, WDT enabled, -40°C to +85°C
µA VDD = 3.0V, WDT disabled, 0°C to +70°C
µA VDD = 3.0V, WDT disabled, -40°C to +85°C
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
1997 Microchip Technology Inc.
DS30234D-page 165
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
16.3
DC Characteristics:
PIC16C61-04 (Commercial, Industrial, Extended)
PIC16C61-20 (Commercial, Industrial, Extended)
PIC16LC61-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +125˚C for extended,
-40˚C ≤ TA ≤ +85˚C for industrial and
DC CHARACTERISTICS
0˚C
≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in DC spec Section 16.1 and
Section 16.2.
Param
No.
Characteristic
Sym
Min Typ† Max Units
Conditions
Input Low Voltage
I/O ports
VIL
D030
D030A
with TTL buffer
Vss
VSS
-
-
0.15VDD
0.8V
V
V
For entire VDD range
4.5V ≤ VDD ≤ 5.5V
D031
with Schmitt Trigger buffer
Vss
Vss
Vss
-
-
-
0.2VDD
0.2VDD
0.3VDD
V
V
V
D032 MCLR, OSC1 (in RC mode)
D033 OSC1 (in XT, HS and LP)
Input High Voltage
Note1
I/O ports
VIH
-
-
-
D040
with TTL buffer
2.0
VDD
VDD
V
V
4.5V ≤ VDD ≤ 5.5V
D040A
0.25VDD
+ 0.8V
For entire VDD range
D041
with Schmitt Trigger buffer
0.85VDD
0.85VDD
0.7VDD
0.9VDD
50
-
-
-
-
VDD
VDD
VDD
VDD
V
V
V
V
For entire VDD range
Note1
D042 MCLR
D042A OSC1 (XT, HS and LP)
D043 OSC1 (in RC mode)
D070 PORTB weak pull-up current
Input Leakage Current (Notes 2, 3)
D060 I/O ports
IPURB
IIL
250 † 400
µA VDD = 5V, VPIN = VSS
-
-
±1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
D061 MCLR, RA4/T0CKI
D063 OSC1
-
-
-
-
±5
±5
µA Vss ≤ VPIN ≤ VDD
µA Vss ≤ VPIN ≤ VDD, XT, HS and
LP osc configuration
Output Low Voltage
D080 I/O ports
VOL
-
-
-
-
-
-
-
-
0.6
0.6
0.6
0.6
V
V
V
V
IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
D080A
IOL = 7.0 mA, VDD = 4.5V,
-40°C to +125°C
D083 OSC2/CLKOUT (RC osc config)
D083A
IOL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 1.2 mA, VDD = 4.5V,
-40°C to +125°C
*
The parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
DS30234D-page 166
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +125˚C for extended,
-40˚C ≤ TA ≤ +85˚C for industrial and
DC CHARACTERISTICS
0˚C
≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in DC spec Section 16.1 and
Section 16.2.
Param
No.
Characteristic
Output High Voltage
Sym
Min Typ† Max Units
Conditions
D090 I/O ports (Note 3)
VOH
VDD-0.7
VDD-0.7
VDD-0.7
VDD-0.7
-
-
-
-
-
-
-
-
V
V
V
V
V
IOH = -3.0 mA,
VDD = 4.5V, -40°C to +85°C
D090A
IOH = -2.5 mA,
VDD = 4.5V, -40°C to +125°C
D092 OSC2/CLKOUT (RC osc config)
D092A
-
IOH = -1.3 mA,
VDD = 4.5V, -40°C to +85°C
-
IOH = -1.0 mA,
VDD = 4.5V, -40°C to +125°C
D150* Open-Drain High Voltage
VOD
14
RA4 pin
Capacitive Loading Specs on
Output Pins
D100 OSC2 pin
COSC2
15
50
pF In XT, HS and LP modes when
external clock is used to drive
OSC1.
D101 All I/O pins and OSC2 (in RC mode) CIO
pF
*
The parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
1997 Microchip Technology Inc.
DS30234D-page 167
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
16.4
Timing Parameter Symbology
The timing parameter symbols have been created following one of the following formats:
2
1. TppS2ppS
2. TppS
3. TCC:ST
4. Ts
(I C specifications only)
2
(I C specifications only)
T
F
Frequency
T
Time
Lowercase letters (pp) and their meanings:
pp
cc
CCP1
CLKOUT
CS
osc
rd
OSC1
RD
ck
cs
di
rw
sc
ss
t0
RD or WR
SCK
SDI
do
dt
SDO
SS
Data in
I/O port
MCLR
T0CKI
T1CKI
WR
io
t1
mc
wr
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
2
I C only
AA
output access
Bus free
High
Low
High
Low
BUF
2
TCC:ST (I C specifications only)
CC
HD
ST
DAT
STA
Hold
SU
Setup
DATA input hold
START condition
STO
STOP condition
FIGURE 16-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load condition 1
VDD/2
Load condition 2
RL
CL
CL
Pin
Pin
VSS
VSS
RL = 464Ω
CL = 50 pF for all pins except OSC2/CLKOUT
15 pF for OSC2 output
DS30234D-page 168
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
16.5
Timing Diagrams and Specifications
FIGURE 16-2: EXTERNAL CLOCK TIMING
Q1
1
Q2
Q3
Q4
4
Q4
Q1
OSC1
3
3
4
2
CLKOUT
TABLE 16-2: EXTERNAL CLOCK TIMING REQUIREMENTS
Parameter
No.
Sym Characteristic
Min
Typ†
Max
Units Conditions
Fosc External CLKIN Frequency
DC
DC
DC
DC
DC
0.1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TCY
—
—
—
—
—
—
4
4
MHz XT and RC osc mode
MHz HS osc mode (-04)
MHz HS osc mode (-20)
kHz LP osc mode
(Note 1)
20
200
4
Oscillator Frequency
(Note 1)
MHz RC osc mode
4
MHz XT osc mode
4
MHz HS osc mode (-04)
MHz HS osc mode (-20)
1
20
1
Tosc External CLKIN Period
250
250
50
—
ns
ns
ns
µs
ns
ns
ns
ns
µs
µs
ns
µs
ns
ns
ns
ns
XT and RC osc mode
HS osc mode (-04)
HS osc mode (-20)
LP osc mode
(Note 1)
—
—
5
—
Oscillator Period
(Note 1)
250
250
250
50
—
RC osc mode
XT osc mode
10,000
1,000
1,000
—
HS osc mode (-04)
HS osc mode (-20)
LP osc mode
5
2
3
TCY
Instruction Cycle Time (Note 1)
1.0
50
DC
—
TCY = 4/Fosc
TosL, External Clock in (OSC1) High or
TosH Low Time
XT oscillator
2.5
10
—
LP oscillator
—
HS oscillator
4
TosR, External Clock in (OSC1) Rise or
TosF Fall Time
25
—
XT oscillator
50
—
LP oscillator
15
—
HS oscillator
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin.
When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices.
1997 Microchip Technology Inc.
DS30234D-page 169
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 16-3: CLKOUT AND I/O TIMING
Q1
Q2
Q3
Q4
OSC1
11
10
CLKOUT
12
13
19
18
14
16
I/O Pin
(input)
15
17
I/O Pin
(output)
new value
old value
20, 21
Note: Refer to Figure 16-1 for load conditions.
TABLE 16-3: CLKOUT AND I/O TIMING REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units Conditions
10*
11*
12*
13*
14*
15*
16*
17*
18*
TosH2ckL
OSC1↑ to CLKOUT↓
—
—
—
—
—
15
15
5
30
ns
ns
ns
ns
ns
ns
ns
ns
ns
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
TosH2ckH OSC1↑ to CLKOUT↑
30
TckR
CLKOUT rise time
15
TckF
CLKOUT fall time
5
15
TckL2ioV
TioV2ckH
TckH2ioI
TosH2ioV
TosH2ioI
CLKOUT ↓ to Port out valid
Port in valid before CLKOUT ↑
Port in hold after CLKOUT ↑
OSC1↑ (Q1 cycle) to Port out valid
—
—
—
—
—
0.5TCY + 20
0.25TCY + 25
—
—
0
—
80 - 100
—
OSC1↑ (Q2 cycle) to Port input invalid
TBD
(I/O in hold time)
19*
20*
TioV2osH
TioR
Port input valid to OSC1↑ (I/O in setup
time)
TBD
—
—
ns
Port output rise time
Port output fall time
PIC16C61
PIC16LC61
PIC16C61
PIC16LC61
—
—
—
—
20
20
10
—
10
—
—
—
25
60
25
60
—
—
ns
ns
ns
ns
ns
ns
21*
TioF
22††*
23††*
Tinp
Trbp
RB0/INT pin high or low time
RB7:RB4 change int high or low time
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
††
These parameters are asynchronous events not related to any internal clock edges.
Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
DS30234D-page 170
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 16-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
OSC
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O Pins
Note: Refer to Figure 16-1 for load conditions.
TABLE 16-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max Units
Conditions
TmcL MCLR Pulse Width (low)
200
7
—
—
ns
30*
31*
VDD = 5V, -40˚C to +125˚C
VDD = 5V, -40˚C to +125˚C
Twdt
Watchdog Timer Time-out Period
18
33
ms
(No Prescaler)
32
Tost
Oscillation Start-up Timer Period
—
28
—
1024TOSC
—
TOSC = OSC1 period
Tpwrt Power-up Timer Period
I/O Hi-impedance from MCLR Low
These parameters are characterized but not tested.
72
—
132
100
ms
ns
33*
34*
VDD = 5V, -40˚C to +125˚C
TIOZ
*
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 171
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 16-5: TIMER0 EXTERNAL CLOCK TIMINGS
RA4/T0CKI
41
40
42
TMR0
Note: Refer to Figure 16-1 for load conditions.
TABLE 16-5: TIMER0 EXTERNAL CLOCK REQUIREMENTS
Parameter Sym Characteristic
No.
Min
Typ† Max Units Conditions
40*
Tt0H T0CKI High Pulse Width
Tt0L T0CKI Low Pulse Width
Tt0P T0CKI Period
No Prescaler
With Prescaler
No Prescaler
With Prescaler
No Prescaler
With Prescaler
0.5TCY + 20
10
—
—
—
—
—
—
—
—
—
—
—
—
ns Must also meet
parameter 42
ns
0.5TCY + 20
10
ns Must also meet
41*
42*
parameter 42
ns
TCY + 40
ns N = prescale value
(2, 4, ..., 256)
Greater of:
20 ns or
TCY + 40
N
ns
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 172
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
17.0 DC AND AC
Note: The data presented in this section is a sta-
CHARACTERISTICS GRAPHS
AND TABLES FOR PIC16C61
The graphs and tables provided in this section are for
design guidance and are not tested or guaranteed.
tistical summary of data collected on units
from different lots over a period of time and
matrix samples. 'Typical' represents the
mean of the distribution while 'max' or 'min'
represents (mean +3σ) and (mean -3σ)
respectively where σ is standard deviation.
In some graphs or tables the data presented are
outside specified operating range (i.e., outside
specified VDD range). This is for information only
and devices are guaranteed to operate properly
only within the specified range.
FIGURE 17-1: TYPICAL RC OSCILLATOR FREQUENCY vs.TEMPERATURE
FOSC
FOSC (25°C)
Frequency Normalized TO +25°C
1.050
REXT = 10 kΩ
CEXT = 100 pF
1.025
1.00
VDD = 5.5V
0.975
0.950
0.925
VDD = 3.5V
0.900
0.875
0.850
0
10
20 25 30
40
50
60
70
T (°C)
TABLE 17-1: RC OSCILLATOR FREQUENCIES
Average
Fosc @ 5V, 25°C
Cext
Rext
20 pF
4.7k
10k
4.52 MHz
2.47 MHz
± 17.35%
± 10.10%
± 11.90%
± 9.43%
100k
3.3k
4.7k
10k
290.86 kHz
1.92 MHz
100 pF
300 pF
1.48 MHz
± 9.83%
788.77 kHz
88.11 kHz
726.89 kHz
573.95 kHz
307.31 kHz
33.82 kHz
± 10.92%
± 16.03%
± 10.97%
± 10.14%
± 10.43%
± 11.24%
100k
3.3k
4.7k
10k
100k
The percentage variation indicated here is part to part variation due to normal process distribution. The variation indi-
cated is ±3 standard deviation from average value for VDD = 5V.
1997 Microchip Technology Inc.
DS30234D-page 173
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 17-2: TYPICAL RC OSCILLATOR
FREQUENCY VS. VDD
FIGURE 17-4: TYPICAL RC OSCILLATOR
FREQUENCY VS. VDD
8.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
5.0
R = 3.3k
4.5
R = 4.7k
4.0
3.5
3.0
R = 4.7k
R = 10k
2.5
R = 10k
2.0
1.5
1.0
Cext = 300 pF, T = 25°C
Cext = 20 pF, T = 25°C
0.5
R = 100k
5.5
R = 100k
5.5
0.0
3.0
0.0
3.0
3.5
4.0
4.5
5.0
6.0
3.5
4.0
4.5
5.0
6.0
VDD (Volts)
VDD (Volts)
FIGURE 17-3: TYPICAL RC OSCILLATOR
FREQUENCY VS. VDD
FIGURE 17-5: TYPICAL IPD VS. VDD
WATCHDOG TIMER
DISABLED 25°C
2.0
0.6
0.5
0.4
R = 3.3k
1.8
1.6
1.4
1.2
1.0
R = 4.7k
0.3
0.2
0.8
0.6
0.4
0.2
0.0
R = 10k
Cext = 100 pF, T = 25°C
0.1
0.0
R = 100k
5.5
3.0
3.5
4.0
4.5
5.0
6.0
VDD (Volts)
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (Volts)
DS30234D-page 174
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 17-6: TYPICAL IPD VS. VDD
FIGURE 17-7: MAXIMUM IPD VS. VDD
WATCHDOG DISABLED
WATCHDOGTIMER ENABLED
25°C
25
14
125°C
12
10
20
15
8
6
10
5
85°C
70°C
4
2
0
0°C
-40°C
-55°C
0
3.0
3.5
4.0
4.5
5.0
5.5
6.0
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (Volts)
VDD (Volts)
1997 Microchip Technology Inc.
DS30234D-page 175
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 17-8: MAXIMUM IPD VS. VDD
WATCHDOG ENABLED*
FIGURE 17-9: VTH (INPUT THRESHOLD
VOLTAGE) OF I/O PINS VS.
VDD
45
-55°C
-40°C
40
35
2.00
1.80
1.60
1.40
1.20
1.00
0.80
0.60
Max (-40°C to 85°C)
25°C, Typ
30
25
125°C
Min (-40°C to 85°C)
20
15
10
5
0°C
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VDD (Volts)
70°C
85°C
0
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (Volts)
*IPD, with Watchdog Timer enabled, has two compo-
nents:The leakage current which increases with higher
temperature and the operating current of the Watchdog
Timer logic which increases with lower temperature. At
-40°C, the latter dominates explaining the apparently
anomalous behavior.
DS30234D-page 176
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 17-10: VIH, VIL OF MCLR,T0CKI AND OSC1 (IN RC MODE) VS. VDD
4.5
4.0
3.5
3.0
VIH, Max (-40°C to 85°C)
VIH, Typ (25°C)
VIH, Min (-40°C to 85°C)
2.5
2.0
1.5
1.0
VIL, Max (-40°C to 85°C)
VIL, Typ (25°C)
VIL, Min (-40°C to 85°C)
0.5
0.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (Volts)
These pins have Schmitt Trigger input buffers.
FIGURE 17-11: VTH (INPUT THRESHOLD VOLTAGE) OF OSC1 INPUT (IN XT, HS, AND LP MODES)
VS. VDD
Max (-40°C to 85°C)
3.6
Typ (25°C)
3.4
3.2
Min (-40°C to 85°C)
3.0
2.8
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
VDD (Volts)
1997 Microchip Technology Inc.
DS30234D-page 177
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 17-12: TYPICAL IDD VS. FREQUENCY (EXTERNAL CLOCK, 25°C)
10,000
1,000
6.0
5.5
5.0
4.5
4.0
3.5
3.0
100
10
1
100,000,000
1,000,000
10,000
10,000,000
100,000
Frequency (Hz)
FIGURE 17-13: MAXIMUM IDD VS. FREQUENCY (EXTERNAL CLOCK, -40° TO +85°C)
10,000
6.0
5.5
5.0
4.5
4.0
3.5
3.0
1,000
100
10
100,000,000
1,000,000
Frequency (Hz)
10,000
10,000,000
100,000
DS30234D-page 178
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 17-14: MAXIMUM IDD VS. FREQUENCY (EXTERNAL CLOCK, -55° TO +125°C)
10,000
6.0
5.5
5.0
4.5
4.0
3.5
3.0
1,000
100
10
100,000,000
10,000
100,000
1,000,000
10,000,000
Frequency (Hz)
FIGURE 17-15: WDT TIMER TIME-OUT
PERIOD VS. VDD
FIGURE 17-16: TRANSCONDUCTANCE (gm)
OF HS OSCILLATOR VS. VDD
50
9000
8000
45
40
35
30
7000
Max. -40°C
6000
5000
Max. 85°C
4000
25
20
Typ. 25°C
Max. 70°C
Typ. 25°C
3000
MIn. 85°C
2000
15
10
5
Min. 0°C
1000
0
Min. -40°C
2
3
4
5
6
7
2
3
4
5
6
7
VDD (Volts)
VDD (Volts)
1997 Microchip Technology Inc.
DS30234D-page 179
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 17-17: TRANSCONDUCTANCE (gm)
OF LP OSCILLATOR VS. VDD
FIGURE 17-19: IOH VS. VOH, VDD = 3V
0
225
200
-5
MIn. 85°C
Max. -40°C
175
150
-10
-15
Typ. 25°C
125
Typ. 25°C
100
MIn. 85°C
75
50
25
0
-20
-25
Max. -40°C
3.0
3.5
4.0
4.5
5.0
5.5
6.0
0
0.5
1.0
1.5
2.0
2.5
VDD (Volts)
3.0
VOH (Volts)
FIGURE 17-18: TRANSCONDUCTANCE (gm)
OF XT OSCILLATOR VS. VDD
FIGURE 17-20: IOH VS. VOH, VDD = 5V
0
-5
2500
Max. -40°C
-10
-15
200
-20
1500
Min @ 85°C
Typ. 25°C
-25
Typ @ 25°C
-30
100
-35
MIn. 85°C
-40
Max @ -40°C
500
-45
-50
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
VOH (Volts)
0
2
3
4
5
6
7
VDD (Volts)
DS30234D-page 180
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 17-21: IOL VS. VOL, VDD = 3V
FIGURE 17-22: IOL VS. VOL, VDD = 5V
90
35
30
25
20
80
Min @ -40°C
Min @ -40°C
70
60
Typ @ 25°C
Typ @ 25°C
50
Min @ +85°C
40
15
10
5
Min @ +85°C
30
20
10
0
0
0.0
1.0
VOL (Volts)
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
0.5
1.5
2.0
2.5
3.0
VOL (Volts)
TABLE 17-2: INPUT CAPACITANCE*
Pin Name
Typical Capacitance (pF)
18L PDIP
5.0
18L SOIC
4.3
RA port
RB port
5.0
4.3
MCLR
17.0
4.0
17.0
3.5
OSC1/CLKIN
OSC2/CLKOUT
T0CKI
4.3
3.5
3.2
2.8
*All capacitance values are typical at 25°C. A part to part variation of ±25% (three standard deviations) should be
taken into account.
1997 Microchip Technology Inc.
DS30234D-page 181
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
NOTES:
DS30234D-page 182
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
18.0 ELECTRICAL CHARACTERISTICS FOR PIC16C62/64
Absolute Maximum Ratings †
Ambient temperature under bias................................................................................................................-55˚C to +85˚C
Storage temperature............................................................................................................................... -65˚C to +150˚C
Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4) ..........................................-0.3V to (VDD + 0.3V)
Voltage on VDD with respect to VSS .......................................................................................................... -0.3V to +7.5V
Voltage on MCLR with respect to VSS (Note 2) ...............................................................................................0V to +14V
Voltage on RA4 with respect to Vss ................................................................................................................0V to +14V
Total power dissipation (Note 1).................................................................................................................................1.0W
Maximum current out of VSS pin ............................................................................................................................300 mA
Maximum current into VDD pin...............................................................................................................................250 mA
Input clamp current, IIK (VI < 0 or VI > VDD) ......................................................................................................................±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD)...............................................................................................................±20 mA
Maximum output current sunk by any I/O pin...........................................................................................................25 mA
Maximum output current sourced by any I/O pin .....................................................................................................25 mA
Maximum current sunk by PORTA, PORTB, and PORTE* (combined) .................................................................200 mA
Maximum current sourced by PORTA, PORTB, and PORTE* (combined)............................................................200 mA
Maximum current sunk by PORTC and PORTD* (combined)................................................................................200 mA
Maximum current sourced by PORTC and PORTD* (combined) ..........................................................................200 mA
* PORTD and PORTE not available on the PIC16C62.
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOl x IOL)
Note 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up.Thus,
a series resistor of 50-100Ω should be used when applying a “low” level to the MCLRpin rather than pulling
this pin directly to VSS.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 18-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16C62-04
PIC16C64-04
PIC16C62-10
PIC16C64-10
PIC16C62-20
PIC16C64-20
PIC16LC62-04
PIC16LC64-04
OSC
JW Devices
RC VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 3.0V to 6.0V
VDD: 4.0V to 6.0V
IDD: 3.8 mA max. at 5.5V IDD: 2.0 mA typ. at 5.5V IDD: 2.0 mA typ. at 5.5V IDD: 3.8 mA max. at 3.0V IDD: 3.8 mA max. at 5.5V
IPD: 21 µA max. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 13.5 µA max. at 3V IPD: 21 µA max. at 4V
Freq:4 MHz max.
Freq:4 MHz max.
Freq:4 MHz max.
Freq: 4 MHz max.
Freq:4 MHz max.
XT VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 3.0V to 6.0V
VDD: 4.0V to 6.0V
IDD: 3.8 mA max. at 5.5V IDD: 2.0 mA typ. at 5.5V IDD: 2.0 mA typ. at 5.5V IDD: 3.8 mA max. at 3.0V IDD: 3.8 mA max. at 5.5V
IPD: 21 µA max. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 13.5 µA max. at 3.0V IPD: 21 µA max. at 4V
Freq:4 MHz max.
Freq:4 MHz max.
Freq:4 MHz max.
Freq: 4 MHz max.
Freq:4 MHz max.
HS VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 13.5 mA typ. at 5.5V IDD: 15 mA max. at 5.5V IDD: 30 mA max. at 5.5V
IDD: 30 mA max. at 5.5V
IPD: 1.5 µA typ. at 4.5V
Freq: 20 MHz max.
Not recommended for
use in HS mode
IPD: 1.5 µA typ. at 4.5V IPD: 1.5 µA typ. at 4.5V IPD: 1.5 µA typ. at 4.5V
Freq:4 MHz max.
Freq: 10 MHz max.
Freq: 20 MHz max.
LP VDD: 4.0V to 6.0V
IDD: 52.5 µA typ.
VDD: 3.0V to 6.0V
IDD: 48 µA max.
at 32 kHz, 3.0V
IPD: 13.5 µA max. at 3.0V IPD:13.5 µA max. at 3.0V
Freq:200 kHz max. Freq:200 kHz max.
VDD: 3.0V to 6.0V
IDD: 48 µA max.
at 32 kHz, 3.0V
Not recommended for
use in LP mode
Not recommended for
use in LP mode
at 32 kHz, 4.0V
IPD: 0.9 µA typ. at 4.0V
Freq:200 kHz max.
The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifications. It is recommended
that the user select the device type that ensures the specifications required.
1997 Microchip Technology Inc.
DS30234D-page 183
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
18.1
DC Characteristics:
PIC16C62/64-04 (Commercial, Industrial)
PIC16C62/64-10 (Commercial, Industrial)
PIC16C62/64-20 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature -40˚C ≤ TA ≤ +85˚C for industrial and
0˚C
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym
VDD
Min Typ† Max Units
Conditions
D001
D001A
Supply Voltage
4.0
4.5
-
-
6.0
5.5
V
V
XT, RC and LP osc configuration
HS osc configuration
D002*
RAM Data Retention
Voltage (Note 1)
VDR
-
1.5
-
V
D003
VDD start voltage to
ensure internal Power-
on Reset signal
VPOR
-
VSS
-
V
See section on Power-on Reset for details
D004*
VDD rise rate to ensure SVDD
internal Power-on
0.05
-
-
V/ms See section on Power-on Reset for details
Reset signal
D010
D013
Supply Current
(Note 2, 5)
IDD
-
-
2.7 5.0 mA XT, RC, osc configuration
FOSC = 4 MHz, VDD = 5.5V (Note 4)
13.5 30
mA HS osc configuration
FOSC = 20 MHz, VDD = 5.5V
D020
D021
D021A
Power-down Current
(Note 3, 5)
IPD
-
-
-
10.5 42
µA VDD = 4.0V, WDT enabled, -40°C to +85°C
µA VDD = 4.0V, WDT disabled, -0°C to +70°C
µA VDD = 4.0V, WDT disabled, -40°C to +85°C
1.5
1.5
21
24
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from charac-
terization and is for design guidance only. This is not tested.
DS30234D-page 184
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
18.2
DC Characteristics: PIC16LC62/64-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature -40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym Min Typ† Max Units
Conditions
D001
Supply Voltage
VDD
VDR
3.0
-
-
6.0
-
V
V
LP, XT, RC osc configuration (DC - 4 MHz)
D002* RAM Data Retention
Voltage (Note 1)
1.5
D003
VDD start voltage to
ensure internal Power-
on Reset signal
VPOR
-
VSS
-
-
-
V
See section on Power-on Reset for details
D004* VDD rise rate to ensure SVDD
internal Power-on
0.05
V/ms See section on Power-on Reset for details
Reset signal
D010
Supply Current
(Note 2, 5)
IDD
-
-
2.0
3.8
mA XT, RC osc configuration
FOSC = 4 MHz, VDD = 3.0V (Note 4)
D010A
22.5 48
7.5 30
µA LP osc configuration
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
D020
D021
D021A
Power-down Current
(Note 3, 5)
IPD
-
-
-
µA VDD = 3.0V, WDT enabled, -40°C to +85°C
0.9 13.5 µA VDD = 3.0V, WDT disabled, 0°C to +70°C
0.9 18 µA VDD = 3.0V, WDT disabled, -40°C to +85°C
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from charac-
terization and is for design guidance only. This is not tested.
1997 Microchip Technology Inc.
DS30234D-page 185
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
18.3
DC Characteristics:
PIC16C62/64-04 (Commercial, Industrial)
PIC16C62/64-10 (Commercial, Industrial)
PIC16C62/64-20 (Commercial, Industrial)
PIC16LC62/64-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40˚C ≤ TA ≤ +85˚C for industrial and
0˚C ≤ TA ≤ +70˚C for commercial
DC CHARACTERISTICS
Operating voltage VDD range as described in DC spec Section 18.1
and Section 18.2
Param
No.
Characteristic
Sym
Min
Typ Max
†
Units
Conditions
Input Low Voltage
I/O ports
VIL
D030
D030A
D031
D032
D033
with TTL buffer
VSS
VSS
VSS
Vss
Vss
-
-
-
-
-
0.15VDD
0.8V
0.2VDD
0.2VDD
0.3VDD
V
V
V
V
V
For entire VDD range
4.5V ≤ VDD ≤ 5.5V
with Schmitt Trigger buffer
MCLR, OSC1 (in RC mode)
OSC1 (in XT, HS and LP)
Input High Voltage
I/O ports
Note1
VIH
D040
D040A
with TTL buffer
2.0
0.25VDD
+ 0.8V
-
-
VDD
VDD
V
V
4.5V ≤ VDD ≤ 5.5V
For entire VDD range
D041
D042
with Schmitt Trigger buffer
MCLR
0.8VDD
0.8VDD
0.7VDD
0.9VDD
50
-
-
-
-
VDD
VDD
VDD
VDD
400
For entire VDD range
Note1
V
V
V
D042A OSC1 (XT, HS and LP)
D043
D070
OSC1 (in RC mode)
PORTB weak pull-up current
Input Leakage Current (Notes 2, 3)
I/O ports
IPURB
IIL
200
µA VDD = 5V, VPIN = VSS
D060
-
-
±1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
D061
D063
MCLR, RA4/T0CKI
OSC1
-
-
-
-
±5
±5
µA Vss ≤ VPIN ≤ VDD
µA Vss ≤ VPIN ≤ VDD, XT, HS and
LP osc configuration
Output Low Voltage
D080
D083
I/O ports
VOL
-
-
-
-
0.6
0.6
V
V
IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
OSC2/CLKOUT (RC osc config)
Output High Voltage
D090
D092
I/O ports (Note 3)
VOH
VOD
VDD-0.7
VDD-0.7
-
-
-
-
-
-
V
V
V
IOH = -3.0 mA, VDD = 4.5V,
-40°C to +85°C
IOH = -1.3 mA, VDD = 4.5V,
-40°C to +85°C
OSC2/CLKOUT (RC osc config)
D150* Open-Drain High Voltage
14
RA4 pin
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and
are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified lev-
els represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
DS30234D-page 186
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +85˚C for industrial and
0˚C ≤ TA ≤ +70˚C for commercial
DC CHARACTERISTICS
Operating voltage VDD range as described in DC spec Section 18.1
and Section 18.2
Param
No.
Characteristic
Sym
Min
Typ Max
†
Units
Conditions
Capacitive Loading Specs on Output
Pins
D100
OSC2 pin
COSC2
-
-
15
pF In XT, HS and LP modes
when external clock is used to
drive OSC1.
D101
D102
All I/O pins and OSC2 (in RC mode)
CIO
Cb
-
-
-
-
50
400
pF
pF
2
SCL, SDA in I C mode
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and
are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified lev-
els represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
1997 Microchip Technology Inc.
DS30234D-page 187
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
18.4
Timing Parameter Symbology
The timing parameter symbols have been created following one of the following formats:
2
1. TppS2ppS
2. TppS
3. TCC:ST
4. Ts
(I C specifications only)
2
(I C specifications only)
T
F
Frequency
T
Time
Lowercase letters (pp) and their meanings:
pp
cc
CCP1
CLKOUT
CS
osc
rd
OSC1
RD
ck
cs
di
rw
sc
ss
t0
RD or WR
SCK
SDI
do
dt
SDO
SS
Data in
I/O port
MCLR
T0CKI
T1CKI
WR
io
t1
mc
wr
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
2
I C only
AA
output access
Bus free
High
Low
High
Low
BUF
2
TCC:ST (I C specifications only)
CC
HD
ST
DAT
STA
Hold
SU
Setup
DATA input hold
START condition
STO
STOP condition
FIGURE 18-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load condition 1
Load condition 2
VDD/2
RL
CL
Pin
CL
VSS
Pin
VSS
Note 1: PORTD and PORTE are not imple-
mented on the PIC16C62.
RL = 464Ω
CL = 50 pF for all pins except OSC2/CLKOUT
but including D and E outputs as ports
15 pF for OSC2 output
DS30234D-page 188
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
18.5
Timing Diagrams and Specifications
FIGURE 18-2: EXTERNAL CLOCK TIMING
Q1
1
Q2
Q3
Q4
4
Q4
Q1
OSC1
3
3
4
2
CLKOUT
TABLE 18-2: EXTERNAL CLOCK TIMING REQUIREMENTS
Parameter
No.
Sym Characteristic
Min
Typ†
Max
Units Conditions
Fosc External CLKIN Frequency
DC
DC
DC
DC
DC
DC
0.1
4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TCY
—
—
—
—
—
—
4
4
MHz XT and RC osc mode
MHz HS osc mode (-04)
MHz HS osc mode (-10)
MHz HS osc mode (-20)
kHz LP osc mode
(Note 1)
10
20
200
4
Oscillator Frequency
(Note 1)
MHz RC osc mode
4
MHz XT osc mode
20
MHz HS osc mode
5
200
—
kHz LP osc mode
1
Tosc External CLKIN Period
250
250
100
50
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
ns
ns
µs
ns
ns
ns
ns
XT and RC osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
(Note 1)
—
—
—
5
—
Oscillator Period
(Note 1)
250
250
250
100
50
—
RC osc mode
10,000
250
250
1,000
—
XT osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
5
2
3
TCY
Instruction Cycle Time (Note 1) 200
DC
—
TCY = 4/FOSC
TosL, External Clock in (OSC1) High
TosH or Low Time
100
2.5
15
—
XT oscillator
—
LP oscillator
—
HS oscillator
4
TosR, External Clock in (OSC1) Rise
TosF or Fall Time
25
XT oscillator
—
50
LP oscillator
—
15
HS oscillator
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin.
When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices.
1997 Microchip Technology Inc.
DS30234D-page 189
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 18-3: CLKOUT AND I/O TIMING
Q1
Q2
Q3
Q4
OSC1
11
10
CLKOUT
12
13
19
18
14
16
I/O Pin
(input)
15
17
I/O Pin
(output)
new value
old value
20, 21
Note: Refer to Figure 18-1 for load conditions.
TABLE 18-3: CLKOUT AND I/O TIMING REQUIREMENTS
Parameters Sym
Characteristic
Min
Typ†
75
75
35
35
—
Max
Units Conditions
10*
11*
12*
13*
14*
15*
16*
17*
18*
TosH2ckL OSC1↑ to CLKOUT↓
TosH2ckH OSC1↑ to CLKOUT↑
—
—
—
—
—
200
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
200
TckR
TckF
CLKOUT rise time
CLKOUT fall time
100
100
TckL2ioV CLKOUT ↓ to Port out valid
TioV2ckH Port in valid before CLKOUT ↑
TckH2ioI Port in hold after CLKOUT ↑
TosH2ioV OSC1↑ (Q1 cycle) to Port out valid
0.5TCY + 20
TOSC + 200
—
—
—
0
—
—
50
—
150
—
TosH2ioI
OSC1↑ (Q2 cycle) to Port
input invalid (I/O in hold time)
PIC16C62/64
100
200
0
PIC16LC62/64
—
—
19*
20*
TioV2osH Port input valid to OSC1↑
—
—
(I/O in setup time)
TioR
TioF
Port output rise time
Port output fall time
INT pin high or low time
PIC16C62/64
PIC16LC62/64
PIC16C62/64
PIC16LC62/64
—
—
10
—
10
—
—
—
40
80
40
80
—
—
ns
ns
ns
ns
ns
ns
21*
—
—
22††*
23††*
Tinp
Trbp
TCY
TCY
RB7:RB4 change INT high or low time
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
†† These parameters are asynchronous events not related to any internal clock edge.
Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
DS30234D-page 190
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 18-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
OSC
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O Pins
Note: Refer to Figure 18-1 for load conditions.
TABLE 18-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max Units
Conditions
30*
31*
TmcL MCLR Pulse Width (low)
100
7
—
—
ns
VDD = 5V, -40˚C to +85˚C
VDD = 5V, -40˚C to +85˚C
Twdt
Watchdog Timer Time-out Period
18
33
ms
(No Prescaler)
32
33*
34*
Tost
Oscillation Start-up Timer Period
—
28
—
1024TOSC
—
—
ms
ns
TOSC = OSC1 period
Tpwrt Power-up Timer Period
I/O Hi-impedance from MCLR Low
These parameters are characterized but not tested.
72
—
132
100
VDD = 5V, -40˚C to +85˚C
TIOZ
*
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 191
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 18-5: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
RA4/T0CKI
41
46
40
45
42
47
RC0/T1OSI/T1CKI
48
TMR0 or
TMR1
Note: Refer to Figure 18-1 for load conditions.
TABLE 18-5: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Param
No.
Sym
Characteristic
Min
Typ† Max Units Conditions
40*
Tt0H
T0CKI High Pulse Width
No Prescaler
0.5TCY + 20
—
—
ns Must also meet
parameter 42
With Prescaler
No Prescaler
10
0.5TCY + 20
10
—
—
—
—
—
—
—
—
—
—
ns
41*
42*
Tt0L
Tt0P
T0CKI Low Pulse Width
T0CKI Period
ns Must also meet
parameter 42
With Prescaler
No Prescaler
With Prescaler
ns
ns
TCY + 40
Greater of:
20 or TCY + 40
ns N = prescale value
(2, 4, ..., 256)
N
0.5TCY + 20
15
45*
46*
47*
Tt1H
Tt1L
Tt1P
T1CKI High Time Synchronous, Prescaler = 1
—
—
—
—
—
—
ns Must also meet
parameter 47
Synchronous, PIC16C6X
ns
ns
Prescaler =
2,4,8
PIC16LC6X
25
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
—
—
—
—
ns
ns
50
T1CKI Low Time
Synchronous, Prescaler = 1
Synchronous, PIC16C6X
0.5TCY + 20
ns Must also meet
parameter 47
15
25
ns
ns
Prescaler =
2,4,8
PIC16LC6X
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
ns
ns
50
T1CKI input period Synchronous PIC16C6X
Greater of:
30 OR TCY + 40
ns N = prescale value
(1, 2, 4, 8)
N
Greater of:
50 OR TCY + 40
N = prescale value
(1, 2, 4, 8)
PIC16LC6X
N
60
Asynchronous PIC16C6X
PIC16LC6X
—
—
—
—
—
ns
ns
100
DC
Ft1
Timer1 oscillator input frequency range
(oscillator enabled by setting bit T1OSCEN)
200
kHz
48
*
TCKEZtmr1 Delay from external clock edge to timer increment
2Tosc
—
7Tosc
—
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 192
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 18-6: CAPTURE/COMPARE/PWM TIMINGS (CCP1)
RC2/CCP1
(Capture Mode)
50
51
52
54
RC2/CCP1
(Compare or
PWM Mode)
53
Note: Refer to Figure 18-1 for load conditions.
TABLE 18-6: CAPTURE/COMPARE/PWM REQUIREMENTS (CCP1)
Parameter Sym Characteristic
No.
Min
Typ† Max Units Conditions
50*
TccL CCP1
input low time
No Prescaler
0.5TCY + 20
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
With Prescaler PIC16C62/64
PIC16LC62/64
10
20
51*
TccH CCP1
input high time
No Prescaler
0.5TCY + 20
With Prescaler PIC16C62/64
PIC16LC62/64
10
20
52*
53
TccP CCP1 input period
3TCY + 40
N
ns N = prescale value
(1,4 or 16)
PIC16C62/64
PIC16LC62/64
PIC16C62/64
PIC16LC62/64
TccR CCP1 output rise time
—
—
—
—
10
25
10
25
25
45
25
45
ns
ns
ns
ns
54
TccF CCP1 output fall time
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 193
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 18-7: PARALLEL SLAVE PORT TIMING (PIC16C64)
RE2/CS
RE0/RD
RE1/WR
65
RD7:RD0
62
64
63
Note: Refer to Figure 18-1 for load conditions
TABLE 18-7: PARALLEL SLAVE PORT REQUIREMENTS (PIC16C64)
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units Conditions
62
TdtV2wrH
TwrH2dtI
Data in valid before WR↑ or CS↑ (setup time)
WR↑ or CS↑ to data–in invalid PIC16C64
20
20
35
—
10
—
—
—
—
—
—
—
—
80
30
ns
ns
ns
ns
ns
63*
(hold time)
PIC16LC64
64
65
TrdL2dtV
TrdH2dtI
RD↓ and CS↓ to data–out valid
RD↑ or CS↑ to data–out invalid
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 194
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 18-8: SPI MODE TIMING
SS
70
SCK
(CKP = 0)
71
72
79
78
78
79
SCK
(CKP = 1)
80
SDO
SDI
77
75, 76
74
73
Note: Refer to Figure 18-1 for load conditions
TABLE 18-8: SPI MODE REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
70
TssL2scH,
TssL2scL
SS↓ to SCK↓ or SCK↑ input
TCY
—
—
ns
71
72
73
TscH
TscL
SCK input high time (slave mode)
SCK input low time (slave mode)
TCY + 20
TCY + 20
50
—
—
—
—
—
—
ns
ns
ns
TdiV2scH,
TdiV2scL
Setup time of SDI data input to SCK
edge
74
TscH2diL,
TscL2diL
Hold time of SDI data input to SCK
edge
50
—
—
ns
75
76
77
78
79
80
TdoR
SDO data output rise time
—
—
10
—
—
—
10
10
—
10
10
—
25
25
50
25
25
50
ns
ns
ns
ns
ns
ns
TdoF
SDO data output fall time
TssH2doZ
TscR
SS↑ to SDO output hi-impedance
SCK output rise time (master mode)
SCK output fall time (master mode)
TscF
TscH2doV,
TscL2doV
SDO data output valid after SCK
edge
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 195
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 18-9: I C BUS START/STOP BITS TIMING
SCL
91
93
92
90
SDA
STOP
Condition
START
Condition
Note: Refer to Figure 18-1 for load conditions
2
TABLE 18-9: I C BUS START/STOP BITS REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min Typ Max Units
Conditions
90
91
92
93
TSU:STA START condition
Setup time
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
4700
600
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Only relevant for repeated START
condition
ns
ns
ns
ns
THD:STA START condition
Hold time
4000
600
After this period the first clock
pulse is generated
TSU:STO STOP condition
Setup time
4700
600
THD:STO STOP condition
Hold time
4000
600
DS30234D-page 196
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 18-10: I C BUS DATA TIMING
103
102
100
101
SCL
90
107
106
91
92
SDA
In
110
109
109
SDA
Out
Note: Refer to Figure 18-1 for load conditions
2
TABLE 18-10: I C BUS DATA REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Max
Units
Conditions
100
THIGH
Clock high time
100 kHz mode
4.0
0.6
—
—
µs
µs
Device must operate at a min-
imum of 1.5 MHz
400 kHz mode
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
4.7
—
—
101
TLOW
Clock low time
100 kHz mode
µs
µs
Device must operate at a min-
imum of 1.5 MHz
400 kHz mode
1.3
—
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
—
—
102
103
TR
TF
SDA and SCL rise
time
100 kHz mode
400 kHz mode
1000
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10 to 400 pF
SDA and SCL fall time 100 kHz mode
400 kHz mode
—
300
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10 to 400 pF
90
91
TSU:STA START condition
setup time
100 kHz mode
400 kHz mode
4.7
0.6
4.0
0.6
0
—
—
µs
µs
µs
µs
ns
µs
ns
ns
µs
µs
ns
ns
µs
µs
Only relevant for repeated
START condition
THD:STA START condition hold 100 kHz mode
—
After this period the first clock
pulse is generated
time
400 kHz mode
100 kHz mode
400 kHz mode
—
106
107
92
THD:DAT Data input hold time
—
0
0.9
—
TSU:DAT Data input setup time 100 kHz mode
400 kHz mode
250
100
4.7
0.6
—
Note 2
—
TSU:STO STOP condition setup 100 kHz mode
—
time
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
—
109
110
TAA
Output valid from
clock
3500
—
Note 1
—
TBUF
Bus free time
4.7
1.3
—
Time the bus must be free
before a new transmission can
start
—
Cb
Bus capacitive loading
—
400
pF
Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of
the falling edge of SCL to avoid unintended generation of START or STOP conditions.
2
2
2: A fast-mode (400 kHz) I C-bus device can be used in a standard-mode (100 kHz) I C-bus system, but the requirement
tsu;DAT ≥ 250 ns must then be met.This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line
2
TR max. + tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I C bus specification) before the SCL line is
released.
1997 Microchip Technology Inc.
DS30234D-page 197
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
NOTES:
DS30234D-page 198
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
19.0 ELECTRICAL CHARACTERISTICS FOR PIC16C62A/R62/64A/R64
Absolute Maximum Ratings †
Ambient temperature under bias..............................................................................................................-55˚C to +125˚C
Storage temperature............................................................................................................................... -65˚C to +150˚C
Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4) ..........................................-0.3V to (VDD + 0.3V)
Voltage on VDD with respect to VSS .......................................................................................................... -0.3V to +7.5V
Voltage on MCLR with respect to VSS (Note 2) ...............................................................................................0V to +14V
Voltage on RA4 with respect to Vss.................................................................................................................0V to +14V
Total power dissipation (Note 1).................................................................................................................................1.0W
Maximum current out of VSS pin ............................................................................................................................300 mA
Maximum current into VDD pin...............................................................................................................................250 mA
Input clamp current, IIK (VI < 0 or VI > VDD) ......................................................................................................................±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD)...............................................................................................................±20 mA
Maximum output current sunk by any I/O pin...........................................................................................................25 mA
Maximum output current sourced by any I/O pin .....................................................................................................25 mA
Maximum current sunk by PORTA, PORTB, and PORTE (combined)...................................................................200 mA
Maximum current sourced by PORTA, PORTB, and PORTE (combined) .............................................................200 mA
Maximum current sunk by PORTC and PORTD (combined).................................................................................200 mA
Maximum current sourced by PORTC and PORTD (combined)............................................................................200 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOl x IOL)
Note 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up.Thus,
a series resistor of 50-100Ω should be used when applying a “low” level to the MCLRpin rather than pulling
this pin directly to VSS.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 19-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16C62A-04
PIC16CR62-04
PIC16C64A-04
PIC16CR64-04
PIC16C62A-10
PIC16CR62-10
PIC16C64A-10
PIC16CR64-10
PIC16C62A-20
PIC16CR62-20
PIC16C64A-20
PIC16CR64-20
PIC16LC62A-04
PIC16LCR62-04
PIC16LC64A-04
PIC16LCR64-04
OSC
JW Devices
RC VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 2.5V to 6.0V
VDD: 4.0V to 6.0V
IDD: 5 mA max. at 5.5V IDD: 2.0 mA typ. at 5.5V IDD: 2.0 mA typ. at 5.5V IDD: 3.8 mA max. at 3.0V IDD: 5 mA max. at 5.5V
IPD: 16 µA max. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 5 µA max. at 3V
IPD: 16 µA max. at 4V
Freq:4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq:4 MHz max.
XT VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 2.5V to 6.0V
VDD: 4.0V to 6.0V
IDD: 5 mA max. at 5.5V IDD: 2.0 mA typ. at 5.5V IDD: 2.0 mA typ. at 5.5V IDD: 3.8 mA max. at 3.0V IDD: 5 mA max. at 5.5V
IPD: 16 µA max. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 5 µA max. at 3.0V
IPD: 16 µA max. at 4V
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
HS VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 13.5 mA typ. at 5.5V IDD: 10 mA max. at 5.5V IDD: 20 mA max. at 5.5V
IDD: 20 mA max. at 5.5V
IPD: 1.5 µA typ. at 4.5V
Freq: 20 MHz max.
Not recommended for use
in HS mode
IPD: 1.5 µA typ. at 4.5V IPD: 1.5 µA typ. at 4.5V IPD: 1.5 µA typ. at 4.5V
Freq: 4 MHz max.
Freq: 10 MHz max.
Freq: 20 MHz max.
LP VDD: 4.0V to 6.0V
IDD: 52.5 µA typ.
VDD: 2.5V to 6.0V
IDD: 48 µA max. at 32
kHz, 3.0V
IPD: 5 µA max. at 3.0V
Freq: 200 kHz max.
VDD: 2.5V to 6.0V
IDD: 48 µA max.
at 32 kHz, 3.0V
IPD: 5 µA max. at 3.0V
Freq: 200 kHz max.
Not recommended for
use in LP mode
Not recommended for
use in LP mode
at 32 kHz, 4.0V
IPD: 0.9 µA typ. at 4.0V
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifications. It is recommended
that the user select the device type that ensures the specifications required.
1997 Microchip Technology Inc.
DS30234D-page 199
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
19.1
DC Characteristics:
PIC16C62A/R62/64A/R64-04 (Commercial, Industrial, Extended)
PIC16C62A/R62/64A/R64-10 (Commercial, Industrial, Extended)
PIC16C62A/R62/64A/R64-20 (Commercial, Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40˚C ≤ TA ≤ +125˚C for extended,
DC CHARACTERISTICS
-40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Supply Voltage
Sym
VDD
Min Typ† Max Units
Conditions
D001
D001A
4.0
4.5
-
-
6.0
5.5
V
V
XT, RC and LP osc configuration
HS osc configuration
D002* RAM Data Retention
Voltage (Note 1)
VDR
-
1.5
-
V
D003
D004*
D005
VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
-
VSS
-
V
See section on Power-on Reset for details
VDD rise rate to ensure
internal Power-on Reset
signal
SVDD
BVDD
0.05
-
-
V/ms See section on Power-on Reset for details
Brown-out Reset Voltage
3.7
3.7
-
4.0 4.3
4.0 4.4
V
V
BODEN bit in configuration word enabled
Extended Range Only
D010
D013
Supply Current (Note 2, 5) IDD
2.7
5
mA XT, RC, osc configuration FOSC = 4 MHz,
VDD = 5.5V (Note 4)
mA HS osc configuration FOSC = 20 MHz,
VDD = 5.5V
-
-
10
20
D015* Brown-out Reset Current
(Note 6)
∆ IBOR
350 425 µA BOR enabled, VDD = 5.0V
D020
D021
D021A
D021B
Power-down Current
(Note 3, 5)
IPD
-
-
-
-
10.5 42 µA VDD = 4.0V, WDT enabled, -40°C to +85°C
1.5
1.5
2.5
16
19
19
µA VDD = 4.0V, WDT disabled, -0°C to +70°C
µA VDD = 4.0V, WDT disabled, -40°C to +85°C
µA VDD = 4.0V, WDT disabled, -40°C to +125°C
D023* Brown-out Reset Current
(Note 6)
∆ IBOR
-
350 425 µA BOR enabled, VDD = 5.0V
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated.These parameters are for design guidance only and
are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from character-
ization and is for design guidance only. This is not tested.
6: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be
added to the base IDD or IPD measurement.
DS30234D-page 200
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
DC Characteristics: PIC16LC62A/R62/64A/R64-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
19.2
DC CHARACTERISTICS
Operating temperature -40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym Min Typ† Max Units
Conditions
D001
Supply Voltage
VDD
2.5
-
-
6.0
-
V
V
LP, XT, RC osc configuration (DC - 4 MHz)
D002*
RAM Data Retention Volt- VDR
age (Note 1)
1.5
D003
VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
SVDD
BVDD
-
VSS
-
-
-
V
See section on Power-on Reset for details
D004*
VDD rise rate to ensure
internal Power-on Reset
signal
0.05
V/ms See section on Power-on Reset for details
D005
D010
Brown-out Reset Voltage
3.7
-
4.0
2.0
4.3
3.8
V
BODEN bit in configuration word enabled
Supply Current (Note 2, 5) IDD
mA XT, RC osc configuration
FOSC = 4 MHz, VDD = 3.0V (Note 4)
D010A
D015*
-
-
22.5 48
350 425
µA LP osc configuration
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
Brown-out Reset Current
(Note 6)
∆IBOR
µA BOR enabled, VDD = 5.0V
D020
D021
D021A
Power-down Current
(Note 3, 5)
IPD
-
-
-
7.5
0.9
0.9
30
5
5
µA VDD = 3.0V, WDT enabled, -40°C to +85°C
µA VDD = 3.0V, WDT disabled, 0°C to +70°C
µA VDD = 3.0V, WDT disabled, -40°C to +85°C
D023*
Brown-out Reset Current
(Note 6)
∆IBOR
-
350 425
µA BOR enabled, VDD = 5.0V
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and
are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from character-
ization and is for design guidance only. This is not tested.
6: The ∆ current is the additional current consumed when this peripheral is enabled.This current should be added
to the base IDD or IPD measurement.
1997 Microchip Technology Inc.
DS30234D-page 201
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
19.3
DC Characteristics:
PIC16C62A/R62/64A/R64-04 (Commercial, Industrial, Extended)
PIC16C62A/R62/64A/R64-10 (Commercial, Industrial, Extended)
PIC16C62A/R62/64A/R64-20 (Commercial, Industrial, Extended)
PIC16LC62A/R62/64A/R64-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +125˚C for extended,
-40˚C ≤ TA ≤ +85˚C for industrial and
DC CHARACTERISTICS
0˚C
≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in DC spec Section 19.1 and
Section 19.2
Param
No.
Characteristic
Sym
Min Typ Max Units
†
Conditions
Input Low Voltage
I/O ports
VIL
D030
D030A
D031
with TTL buffer
Vss
VSS
Vss
Vss
Vss
-
-
-
-
-
0.15VDD
0.8V
0.2VDD
0.2VDD
0.3VDD
V
V
V
V
V
For entire VDD range
4.5V ≤ VDD ≤ 5.5V
with Schmitt Trigger buffer
D032 MCLR, OSC1 (in RC mode)
D033 OSC1 (in XT, HS and LP)
Input High Voltage
Note1
I/O ports
VIH
-
-
-
D040
D040A
with TTL buffer
2.0
0.25VDD
+ 0.8V
VDD
VDD
V
V
4.5V ≤ VDD ≤ 5.5V
For entire VDD range
D041
D042 MCLR
with Schmitt Trigger buffer
0.8VDD
0.8VDD
0.7VDD
0.9VDD
50
-
-
-
-
VDD
VDD
VDD
VDD
400
V
V
V
V
For entire VDD range
Note1
D042A OSC1 (XT, HS and LP)
D043 OSC1 (in RC mode)
D070 PORTB weak pull-up current
Input Leakage Current (Notes 2, 3)
D060 I/O ports
IPURB
IIL
250
µA VDD = 5V, VPIN = VSS
-
-
±1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-imped-
ance
D061 MCLR, RA4/T0CKI
D063 OSC1
-
-
-
-
±5
±5
µA Vss ≤ VPIN ≤ VDD
µA Vss ≤ VPIN ≤ VDD, XT, HS and LP
osc configuration
Output Low Voltage
D080 I/O ports
VOL
-
-
-
-
-
-
-
-
0.6
0.6
0.6
0.6
V
V
V
V
IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 7.0 mA, VDD = 4.5V,
-40°C to +125°C
IOL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 1.2 mA, VDD = 4.5V,
-40°C to +125°C
D080A
D083 OSC2/CLKOUT (RC osc config)
D083A
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and
are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified lev-
els represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
DS30234D-page 202
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +125˚C for extended,
-40˚C ≤ TA ≤ +85˚C for industrial and
DC CHARACTERISTICS
0˚C
≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in DC spec Section 19.1 and
Section 19.2
Param
No.
Characteristic
Output High Voltage
Sym
Min Typ Max Units
†
Conditions
D090 I/O ports (Note 3)
VOH
VDD-0.7
VDD-0.7
VDD-0.7
VDD-0.7
-
-
-
-
-
-
-
-
V
V
V
V
V
IOH = -3.0 mA, VDD = 4.5V,
-40°C to +85°C
IOH = -2.5 mA, VDD = 4.5V,
-40°C to +125°C
IOH = -1.3 mA, VDD = 4.5V,
-40°C to +85°C
IOH = -1.0 mA, VDD = 4.5V,
-40°C to +125°C
D090A
D092 OSC2/CLKOUT (RC osc config)
D092A
-
-
D150* Open-Drain High Voltage
Capacitive Loading Specs on Out-
put Pins
VOD
14
RA4 pin
D100 OSC2 pin
COSC2
-
-
15
pF In XT, HS and LP modes when
external clock is used to drive
OSC1.
D101 All I/O pins and OSC2 (in RC mode) CIO
-
-
-
-
50
400
pF
pF
2
D102
Cb
SCL, SDA in I C mode
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and
are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified lev-
els represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
1997 Microchip Technology Inc.
DS30234D-page 203
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
19.4
Timing Parameter Symbology
The timing parameter symbols have been created following one of the following formats:
2
1. TppS2ppS
2. TppS
3. TCC:ST
4. Ts
(I C specifications only)
2
(I C specifications only)
T
F
Frequency
T
Time
Lowercase letters (pp) and their meanings:
pp
cc
CCP1
CLKOUT
CS
osc
rd
OSC1
RD
ck
cs
di
rw
sc
ss
t0
RD or WR
SCK
SDI
do
dt
SDO
SS
Data in
I/O port
MCLR
T0CKI
T1CKI
WR
io
t1
mc
wr
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
2
I C only
AA
output access
Bus free
High
Low
High
Low
BUF
2
TCC:ST (I C specifications only)
CC
HD
ST
DAT
STA
Hold
SU
Setup
DATA input hold
START condition
STO
STOP condition
FIGURE 19-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load condition 1
Load condition 2
VDD/2
RL
CL
Pin
VSS
CL
Pin
VSS
RL = 464Ω
CL = 50 pF for all pins except OSC2/CLKOUT
but including D and E outputs as ports
Note 1: PORTD and PORTE are not
implemented on the
15 pF for OSC2 output
PIC16C62A/R62.
DS30234D-page 204
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
19.5
Timing Diagrams and Specifications
FIGURE 19-2: EXTERNAL CLOCK TIMING
Q1
1
Q2
Q3
Q4
4
Q4
Q1
OSC1
3
3
4
2
CLKOUT
TABLE 19-2: EXTERNAL CLOCK TIMING REQUIREMENTS
Parameter
No.
Sym Characteristic
Min
Typ†
Max
Units Conditions
Fosc External CLKIN Frequency
(Note 1)
DC
DC
DC
DC
DC
DC
0.1
4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TCY
—
—
—
—
—
—
4
4
MHz XT and RC osc mode
MHz HS osc mode (-04)
MHz HS osc mode (-10)
MHz HS osc mode (-20)
kHz LP osc mode
10
20
200
4
Oscillator Frequency
(Note 1)
MHz RC osc mode
4
MHz XT osc mode
20
200
—
MHz HS osc mode
5
kHz LP osc mode
1
Tosc External CLKIN Period
250
250
100
50
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
ns
ns
µs
ns
ns
ns
ns
XT and RC osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
(Note 1)
—
—
—
5
—
Oscillator Period
(Note 1)
250
250
250
100
50
—
RC osc mode
10,000
250
250
250
—
XT osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
5
2
3
TCY
Instruction Cycle Time (Note 1)
200
100
2.5
15
DC
—
TCY = 4/FOSC
TosL, External Clock in (OSC1) High or
TosH Low Time
XT oscillator
—
LP oscillator
—
HS oscillator
4
TosR, External Clock in (OSC1) Rise or
TosF Fall Time
—
25
50
15
XT oscillator
—
LP oscillator
—
HS oscillator
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin.
When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices.
1997 Microchip Technology Inc.
DS30234D-page 205
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 19-3: CLKOUT AND I/O TIMING
Q1
Q2
Q3
Q4
OSC1
10
11
CLKOUT
13
12
19
18
14
16
I/O Pin
(input)
15
17
I/O Pin
(output)
new value
old value
20, 21
Note: Refer to Figure 19-1 for load conditions.
TABLE 19-3: CLKOUT AND I/O TIMING REQUIREMENTS
Parameters Sym
Characteristic
OSC1↑ to CLKOUT↓
Min
Typ†
75
75
35
35
—
Max
Units Conditions
10*
11*
12*
13*
14*
15*
16*
17*
18*
TosH2ckL
—
—
—
—
—
200
ns
ns
ns
ns
ns
ns
ns
ns
ns
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
TosH2ckH OSC1↑ to CLKOUT↑
200
TckR
CLKOUT rise time
100
TckF
CLKOUT fall time
100
TckL2ioV
TioV2ckH
TckH2ioI
TosH2ioV
TosH2ioI
CLKOUT ↓ to Port out valid
Port in valid before CLKOUT ↑
Port in hold after CLKOUT ↑
OSC1↑ (Q1 cycle) to Port out valid
OSC1↑ (Q2 cycle) to Port input PIC16C62A/
0.5TCY + 20
Tosc + 200
—
—
—
0
—
—
50
—
150
—
100
invalid (I/O in hold time)
R62/64A/R64
PIC16LC62A/
200
—
—
ns
R62/64A/R64
19*
20*
TioV2osH
TioR
Port input valid to OSC1↑ (I/O in setup time)
0
—
—
ns
ns
Port output rise time
PIC16C62A/
—
10
40
R62/64A/R64
PIC16LC62A/
R62/64A/R64
—
—
—
—
10
—
80
40
80
ns
ns
ns
21*
TioF
Port output fall time
PIC16C62A/
R62/64A/R64
PIC16LC62A/
R62/64A/R64
22††*
23††*
Tinp
Trbp
RB0/INT pin high or low time
TCY
TCY
—
—
—
—
ns
ns
RB7:RB4 change int high or low time
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
†† These parameters are asynchronous events not related to any internal clock edge.
Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
DS30234D-page 206
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 19-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
OSC
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O Pins
Note: Refer to Figure 19-1 for load conditions.
FIGURE 19-5: BROWN-OUT RESET TIMING
BVDD
VDD
35
TABLE 19-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER,
AND BROWN-OUT RESET REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max Units
Conditions
30
TmcL MCLR Pulse Width (low)
2
7
—
—
µs VDD = 5V, -40˚C to +125˚C
31*
Twdt
Watchdog Timer Time-out Period
18
33
ms
VDD = 5V, -40˚C to +125˚C
(No Prescaler)
32
33*
34
Tost
Oscillation Start-up Timer Period
—
28
—
1024TOSC
—
—
ms
µs
TOSC = OSC1 period
Tpwrt Power-up Timer Period
72
—
132
2.1
VDD = 5V, -40˚C to +125˚C
TIOZ
I/O Hi-impedance from MCLR Low
or WDT Reset
35
TBOR
Brown-out Reset Pulse Width
100
—
—
VDD ≤ BVDD (param. D005)
µs
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 207
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 19-6: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
RA4/T0CKI
41
40
42
RC0/T1OSO/T1CKI
46
45
47
48
TMR0 or
TMR1
Note: Refer to Figure 19-1 for load conditions.
TABLE 19-5: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Param
No.
Sym
Characteristic
Min
Typ† Max Units Conditions
40*
Tt0H
T0CKI High Pulse Width
No Prescaler
0.5TCY + 20
—
—
ns Must also meet
parameter 42
With Prescaler
No Prescaler
10
0.5TCY + 20
10
—
—
—
—
—
—
—
—
—
—
ns
41*
42*
Tt0L
Tt0P
T0CKI Low Pulse Width
T0CKI Period
ns Must also meet
parameter 42
With Prescaler
No Prescaler
With Prescaler
ns
ns
TCY + 40
Greater of:
20 or TCY + 40
ns N = prescale value
(2, 4, ..., 256)
N
0.5TCY + 20
15
45*
46*
47*
Tt1H
Tt1L
Tt1P
T1CKI High Time Synchronous, Prescaler = 1
—
—
—
—
—
—
ns Must also meet
parameter 47
Synchronous, PIC16C6X
ns
ns
Prescaler =
2,4,8
PIC16LC6X
25
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
—
—
—
—
ns
ns
50
T1CKI Low Time
Synchronous, Prescaler = 1
Synchronous, PIC16C6X
0.5TCY + 20
ns Must also meet
parameter 47
15
25
ns
ns
Prescaler =
2,4,8
PIC16LC6X
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
ns
ns
50
T1CKI input period Synchronous PIC16C6X
Greater of:
30 OR TCY + 40
ns N = prescale value
(1, 2, 4, 8)
N
Greater of:
50 OR TCY + 40
N = prescale value
(1, 2, 4, 8)
PIC16LC6X
N
60
Asynchronous PIC16C6X
PIC16LC6X
—
—
—
—
—
ns
ns
100
DC
Ft1
Timer1 oscillator input frequency range
(oscillator enabled by setting bit T1OSCEN)
200
kHz
48
*
TCKEZtmr1 Delay from external clock edge to timer increment
2Tosc
—
7Tosc
—
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 208
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 19-7: CAPTURE/COMPARE/PWM TIMINGS (CCP1)
RC2/CCP1
(Capture Mode)
50
51
52
54
RC2/CCP1
(Compare or
PWM Mode)
53
Note: Refer to Figure 19-1 for load conditions.
TABLE 19-6: CAPTURE/COMPARE/PWM REQUIREMENTS (CCP1)
Parameter Sym Characteristic
No.
Min
Typ† Max Units Conditions
50*
TccL CCP1
input low time
No Prescaler
0.5TCY + 20
10
—
—
—
—
ns
ns
With Prescaler PIC16C62A/R62/
64A/R64
PIC16LC62A/R62/
20
—
—
ns
64A/R64
51*
TccH
No Prescaler
0.5TCY + 20
10
—
—
—
—
ns
ns
CCP1
input high time
With Prescaler PIC16C62A/R62/
64A/R64
PIC16LC62A/R62/
64A/R64
20
—
—
10
25
10
25
—
—
25
45
25
45
ns
52*
53*
TccP
3TCY + 40
N
ns N = prescale value
(1,4 or 16)
CCP1 input period
TccR CCP1 output rise time
PIC16C62A/R62/
64A/R64
—
—
—
—
ns
ns
ns
ns
PIC16LC62A/R62/
64A/R64
54*
TccF CCP1 output fall time
PIC16C62A/R62/
64A/R64
PIC16LC62A/R62/
64A/R64
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 209
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 19-8: PARALLEL SLAVE PORT TIMING (PIC16C64A/R64)
RE2/CS
RE0/RD
RE1/WR
65
RD7:RD0
62
64
63
Note: Refer to Figure 19-1 for load conditions
TABLE 19-7: PARALLEL SLAVE PORT REQUIREMENTS (PIC16C64A/R64)
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units Conditions
62
TdtV2wrH Data in valid before WR↑ or CS↑ (setup time)
20
25
—
—
—
—
ns
ns
Extended
Range Only
63*
64
TwrH2dtI WR↑ or CS↑ to data–in invalid (hold PIC16C64A/R64
20
—
—
—
—
—
—
80
90
ns
ns
ns
ns
time)
PIC16LC64A/R64 35
TrdL2dtV RD↓ and CS↓ to data–out valid
—
—
Extended
Range Only
65*
TrdH2dtI RD↑ or CS↑ to data–out invalid
10
—
30
ns
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 210
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 19-9: SPI MODE TIMING
SS
70
SCK
(CKP = 0)
71
72
78
79
79
78
SCK
(CKP = 1)
80
SDO
SDI
77
75, 76
74
73
Note: Refer to Figure 19-1 for load conditions
TABLE 19-8: SPI MODE REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
70*
TssL2scH,
TssL2scL
SS↓ to SCK↓ or SCK↑ input
TCY
—
—
ns
71*
72*
73*
TscH
TscL
SCK input high time (slave mode)
SCK input low time (slave mode)
TCY + 20
TCY + 20
50
—
—
—
—
—
—
ns
ns
ns
TdiV2scH,
TdiV2scL
Setup time of SDI data input to SCK
edge
74*
TscH2diL,
TscL2diL
Hold time of SDI data input to SCK
edge
50
—
—
ns
75*
76*
77*
78*
79*
80*
TdoR
SDO data output rise time
—
—
10
—
—
—
10
10
—
10
10
—
25
25
50
25
25
50
ns
ns
ns
ns
ns
ns
TdoF
SDO data output fall time
TssH2doZ
TscR
SS↑ to SDO output hi-impedance
SCK output rise time (master mode)
SCK output fall time (master mode)
TscF
TscH2doV,
TscL2doV
SDO data output valid after SCK
edge
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 211
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 19-10: I C BUS START/STOP BITS TIMING
SCL
91
93
90
92
SDA
STOP
Condition
START
Condition
Note: Refer to Figure 19-1 for load conditions
2
TABLE 19-9: I C BUS START/STOP BITS REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min Typ Max Units
Conditions
90*
91*
92*
93*
TSU:STA START condition
Setup time
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
4700
600
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Only relevant for repeated START
condition
ns
ns
ns
ns
THD:STA START condition
Hold time
4000
600
After this period the first clock
pulse is generated
TSU:STO STOP condition
Setup time
4700
600
THD:STO STOP condition
Hold time
4000
600
*These parameters are characterized but not tested.
DS30234D-page 212
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 19-11: I C BUS DATA TIMING
103
102
100
101
SCL
90
106
107
92
91
SDA
In
110
109
109
SDA
Out
Note: Refer to Figure 19-1 for load conditions
2
TABLE 19-10: I C BUS DATA REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Max
Units
Conditions
100*
THIGH
Clock high time
100 kHz mode
400 kHz mode
4.0
0.6
—
—
µs
µs
Device must operate at a min-
imum of 1.5 MHz
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
4.7
—
—
101*
TLOW
Clock low time
100 kHz mode
µs
µs
Device must operate at a min-
imum of 1.5 MHz
400 kHz mode
1.3
—
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
—
—
102*
103*
TR
TF
SDA and SCL rise
time
100 kHz mode
400 kHz mode
1000
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10-400 pF
SDA and SCL fall time 100 kHz mode
400 kHz mode
—
300
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10-400 pF
90*
91*
TSU:STA START condition
setup time
100 kHz mode
400 kHz mode
4.7
0.6
4.0
0.6
0
—
—
µs
µs
µs
µs
ns
µs
ns
ns
µs
µs
ns
ns
µs
µs
Only relevant for repeated
START condition
THD:STA START condition hold 100 kHz mode
—
After this period the first clock
pulse is generated
time
400 kHz mode
100 kHz mode
400 kHz mode
—
106*
107*
92*
THD:DAT Data input hold time
—
0
0.9
—
TSU:DAT Data input setup time 100 kHz mode
400 kHz mode
250
100
4.7
0.6
—
Note 2
—
TSU:STO STOP condition setup 100 kHz mode
—
time
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
—
109*
110*
TAA
Output valid from
clock
3500
—
Note 1
—
TBUF
Bus free time
4.7
1.3
—
Time the bus must be free
before a new transmission can
start
—
Cb
Bus capacitive loading
—
400
pF
*
These parameters are characterized but not tested.
Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of
the falling edge of SCL to avoid unintended generation of START or STOP conditions.
2
2
2: A fast-mode (400 kHz) I C-bus device can be used in a standard-mode (100 kHz) I C-bus system, but the requirement
tsu;DAT ≥ 250 ns must then be met.This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line
2
TR max.+tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I C bus specification) before the SCL line is
released.
1997 Microchip Technology Inc.
DS30234D-page 213
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
NOTES:
DS30234D-page 214
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
20.0 ELECTRICAL CHARACTERISTICS FOR PIC16C65
Absolute Maximum Ratings †
Ambient temperature under bias................................................................................................................-55˚C to +85˚C
Storage temperature............................................................................................................................... -65˚C to +150˚C
Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4) ..........................................-0.3V to (VDD + 0.3V)
Voltage on VDD with respect to VSS .......................................................................................................... -0.3V to +7.5V
Voltage on MCLR with respect to VSS (Note 2) ...............................................................................................0V to +14V
Voltage on RA4 with respect to Vss.................................................................................................................0V to +14V
Total power dissipation (Note 1).................................................................................................................................1.0W
Maximum current out of VSS pin ............................................................................................................................300 mA
Maximum current into VDD pin...............................................................................................................................250 mA
Input clamp current, IIK (VI < 0 or VI > VDD) ......................................................................................................................±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD)...............................................................................................................±20 mA
Maximum output current sunk by any I/O pin...........................................................................................................25 mA
Maximum output current sourced by any I/O pin .....................................................................................................25 mA
Maximum current sunk by PORTA, PORTB, and PORTE (combined)...................................................................200 mA
Maximum current sourced by PORTA, PORTB, and PORTE (combined) .............................................................200 mA
Maximum current sunk by PORTC and PORTD (combined).................................................................................200 mA
Maximum current sourced by PORTC and PORTD (combined)............................................................................200 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOl x IOL)
Note 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up.Thus,
a series resistor of 50-100Ω should be used when applying a “low” level to the MCLRpin rather than pulling
this pin directly to VSS.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 20-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
OSC
PIC16C65-04
PIC16C65-10
PIC16C65-20
PIC16LC65-04
JW Devices
RC VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 3.0V to 6.0V
VDD: 4.0V to 6.0V
IDD: 5 mA max. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 3.8 mA max. at 3V IDD: 5 mA max. at 5.5V
IPD: 21 µA max. at 4V IPD: 1.5 µA typ. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 800 µA max. at 3V IPD: 21 µA max. at 4V
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
XT VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 3.0V to 6.0V
VDD: 4.0V to 6.0V
IDD: 5 mA max. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 3.8 mA max. at 3V IDD: 5 mA max. at 5.5V
IPD: 21 µA max. at 4V IPD: 1.5 µA typ. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 800 µA max. at 3V IPD: 21 µA max. at 4V
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
HS VDD:4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 13.5 mA typ. at
5.5V
IDD: 15 mA max. at 5.5V IDD: 30 mA max. at
5.5V
IDD: 30 mA max. at 5.5V
Not recommended for
use in HS mode
IPD: 1.5 µA typ. at 4.5V IPD 1.0 µA typ. at 4.5V IPD: 1.5 µA typ. at 4.5V
IPD: 1.5 µA typ. at 4.5V
Freq: 4 MHz max.
Freq: 10 MHz max.
Freq: 20 MHz max.
Freq: 20 MHz max.
LP VDD: 4.0V to 6.0V
IDD: 52.5 µA typ.
VDD: 3.0V to 6.0V
IDD: 105 µA max.
at 32 kHz, 3.0V
IPD: 800 µA max. at
3.0V
VDD: 3.0V to 6.0V
IDD: 105 µA max.
at 32 kHz, 3.0V
IPD: 800 µA max. at
3.0V
Not recommended for
use in LP mode
Not recommended for
use in LP mode
at 32 kHz, 4.0V
IPD: 0.9 µA typ. at 4.0V
Freq: 200 kHz max.
Freq: 200 kHz max.
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifications. It is recom-
mended that the user select the device type that ensures the specifications required.
1997 Microchip Technology Inc.
DS30234D-page 215
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
20.1
DC Characteristics:
PIC16C65-04 (Commercial, Industrial)
PIC16C65-10 (Commercial, Industrial)
PIC16C65-20 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40˚C ≤ TA ≤ +85˚C for industrial and
DC CHARACTERISTICS
0˚C
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Supply Voltage
Sym
VDD
Min Typ† Max Units
Conditions
D001
D001A
4.0
4.5
-
-
6.0
5.5
V
V
XT, RC and LP osc configuration
HS osc configuration
D002* RAM Data Retention
Voltage (Note 1)
VDR
-
1.5
-
V
D003
VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
-
VSS
-
V
See section on Power-on Reset for details
D004* VDD rise rate to ensure
internal Power-on Reset
signal
SVDD
0.05
-
-
V/ms See section on Power-on Reset for details
D010
Supply Current (Note 2, 5) IDD
-
-
2.7
5
mA XT, RC osc configuration
FOSC = 4 MHz, VDD = 5.5V (Note 4)
D013
13.5 30
mA HS osc configuration
FOSC = 20 MHz, VDD = 5.5V
D020
D021
D021A
Power-down Current
(Note 3, 5)
IPD
-
-
-
10.5 800 µA VDD = 4.0V, WDT enabled,-40°C to +85°C
1.5 800 µA VDD = 4.0V, WDT disabled,-0°C to +70°C
1.5 800 µA VDD = 4.0V, WDT disabled,-40°C to +85°C
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,
MCLR = VDD; WDT enabled/disabled as specified.
3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from character-
ization and is for design guidance only. This is not tested.
DS30234D-page 216
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
20.2
DC Characteristics: PIC16LC65-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature -40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym Min Typ† Max Units
Conditions
D001 Supply Voltage
VDD
VDR
3.0
-
-
6.0
-
V
V
LP, XT, RC osc configuration (DC - 4 MHz)
D002* RAM Data Retention
Voltage (Note 1)
1.5
D003 VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
SVDD
-
VSS
-
-
-
V
See section on Power-on Reset for details
D004* VDD rise rate to ensure
internal Power-on Reset
signal
0.05
V/ms See section on Power-on Reset for details
D010 Supply Current (Note 2, 5) IDD
-
-
2.0
3.8
mA XT, RC osc configuration
FOSC = 4 MHz, VDD = 3.0V (Note 4)
D010A
22.5 105
µA LP osc configuration
FOSC = 32 kHz, VDD = 4.0V, WDT disabled
D020 Power-down Current
D021 (Note 3, 5)
D021A
IPD
-
-
-
7.5 800
0.9 800
0.9 800
µA VDD = 3.0V, WDT enabled, -40°C to +85°C
µA VDD = 3.0V, WDT disabled, 0°C to +70°C
µA VDD = 3.0V, WDT disabled, -40°C to +85°C
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,
MCLR = VDD; WDT enabled/disabled as specified.
3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from character-
ization and is for design guidance only. This is not tested.
1997 Microchip Technology Inc.
DS30234D-page 217
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
20.3
DC Characteristics:
PIC16C65-04 (Commercial, Industrial)
PIC16C65-10 (Commercial, Industrial)
PIC16C65-20 (Commercial, Industrial)
PIC16LC65-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +85˚C for industrial and
0˚C ≤ TA ≤ +70˚C for commercial
DC CHARACTERISTICS
Operating voltage VDD range as described in DC spec Section 20.1 and
Section 20.2
Param
No.
Characteristic
Sym
Min
Typ Max
†
Units
Conditions
Input Low Voltage
I/O ports
VIL
D030
D030A
D031
D032
D033
with TTL buffer
VSS
VSS
VSS
Vss
Vss
-
-
-
-
-
0.15VDD
0.8V
0.2VDD
0.2VDD
0.3VDD
V
V
V
V
V
For entire VDD range
4.5V ≤ VDD ≤ 5.5V
with Schmitt Trigger buffer
MCLR, OSC1(in RC mode)
OSC1 (in XT, HS and LP)
Input High Voltage
I/O ports
Note1
VIH
-
-
-
D040
D040A
with TTL buffer
2.0
0.25VDD
+ 0.8V
VDD
VDD
V
V
4.5V ≤ VDD ≤ 5.5V
For entire VDD range
D041
D042
with Schmitt Trigger buffer
MCLR
0.8VDD
0.8VDD
0.7 VDD
0.9VDD
50
-
-
-
-
VDD
VDD
VDD
VDD
400
For entire VDD range
Note1
V
V
V
D042A OSC1 (XT, HS and LP)
D043
D070
OSC1 (in RC mode)
PORTB weak pull-up current
Input Leakage Current
(Notes 2, 3)
IPURB
IIL
250
µA VDD = 5V, VPIN = VSS
D060
I/O ports
-
-
±1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
D061
D063
MCLR, RA4/T0CKI
OSC1
-
-
-
-
±5
±5
µA Vss ≤ VPIN ≤ VDD
µA Vss ≤ VPIN ≤ VDD, XT, HS, and
LP osc configuration
Output Low Voltage
D080
D083
I/O ports
VOL
-
-
-
-
0.6
0.6
V
V
IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
OSC2/CLKOUT (RC osc config)
Output High Voltage
D090
D092
I/O ports (Note 3)
VOH
VOD
VDD-0.7
VDD-0.7
-
-
-
-
-
-
V
V
V
IOH = -3.0 mA, VDD = 4.5V,
-40°C to +85°C
IOH = -1.3 mA, VDD = 4.5V,
-40°C to +85°C
OSC2/CLKOUT (RC osc config)
D150* Open-Drain High Voltage
14
RA4 pin
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
DS30234D-page 218
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +85˚C for industrial and
0˚C ≤ TA ≤ +70˚C for commercial
DC CHARACTERISTICS
Operating voltage VDD range as described in DC spec Section 20.1 and
Section 20.2
Param
No.
Characteristic
Sym
Min
Typ Max
†
Units
Conditions
Capacitive Loading Specs on
Output Pins
D100
OSC2 pin
COSC2
-
-
15
pF In XT, HS and LP modes when
external clock is used to drive
OSC1.
D101
D102
All I/O pins and OSC2 (in RC mode) CIO
-
-
-
-
50
400
pF
pF
2
Cb
SCL, SDA in I C mode
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
1997 Microchip Technology Inc.
DS30234D-page 219
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
20.4
Timing Parameter Symbology
The timing parameter symbols have been created following one of the following formats:
2
1. TppS2ppS
2. TppS
3. TCC:ST
4. Ts
(I C specifications only)
2
(I C specifications only)
T
F
Frequency
T
Time
Lowercase letters (pp) and their meanings:
pp
cc
CCP1
CLKOUT
CS
osc
rd
OSC1
RD
ck
cs
di
rw
sc
ss
t0
RD or WR
SCK
SDI
do
dt
SDO
SS
Data in
I/O port
MCLR
T0CKI
T1CKI
WR
io
t1
mc
wr
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
2
I C only
AA
output access
Bus free
High
Low
High
Low
BUF
2
TCC:ST (I C specifications only)
CC
HD
ST
DAT
STA
Hold
SU
Setup
DATA input hold
START condition
STO
STOP condition
FIGURE 20-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load condition 1
VDD/2
Load condition 2
CL
Pin
RL
VSS
CL
Pin
RL = 464Ω
VSS
CL = 50 pF for all pins except OSC2/CLKOUT
but including D and E outputs as ports
15 pF for OSC2 output
DS30234D-page 220
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
20.5
Timing Diagrams and Specifications
FIGURE 20-2: EXTERNAL CLOCK TIMING
Q1
1
Q2
Q3
Q4
4
Q4
Q1
OSC1
3
3
4
2
CLKOUT
TABLE 20-2: EXTERNAL CLOCK TIMING REQUIREMENTS
Parameter
No.
Sym Characteristic
Min
Typ†
Max
Units Conditions
Fosc External CLKIN Frequency
DC
DC
DC
DC
DC
DC
0.1
4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TCY
—
—
—
—
—
—
4
4
MHz XT and RC osc mode
MHz HS osc mode (-04)
MHz HS osc mode (-10)
MHz HS osc mode (-20)
kHz LP osc mode
(Note 1)
10
20
200
4
Oscillator Frequency
(Note 1)
MHz RC osc mode
4
MHz XT osc mode
20
200
—
MHz HS osc mode
5
kHz LP osc mode
1
Tosc External CLKIN Period
250
250
100
50
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
ns
ns
µs
ns
ns
ns
ns
XT and RC osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
(Note 1)
—
—
—
5
—
Oscillator Period
(Note 1)
250
250
250
100
50
—
RC osc mode
10,000
250
250
250
—
XT osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
5
2
3
TCY
Instruction Cycle Time (Note 1)
200
50
DC
—
TCY = 4/FOSC
TosL, External Clock in (OSC1) High or
TosH Low Time
XT oscillator
2.5
15
—
LP oscillator
—
HS oscillator
4
TosR, External Clock in (OSC1) Rise or
TosF Fall Time
—
25
50
15
XT oscillator
—
LP oscillator
—
HS oscillator
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin.
When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices.
1997 Microchip Technology Inc.
DS30234D-page 221
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 20-3: CLKOUT AND I/O TIMING
Q1
Q2
Q3
Q4
OSC1
11
10
CLKOUT
12
13
19
18
14
16
I/O Pin
(input)
15
17
I/O Pin
(output)
new value
old value
20, 21
Note: Refer to Figure 20-1 for load conditions.
TABLE 20-3: CLKOUT AND I/O TIMING REQUIREMENTS
Parameter Sym
No.
Characteristic
Min
Typ†
Max
Units Conditions
10*
11*
12*
13*
14*
15*
16*
17*
18*
TosH2ckL
OSC1↑ to CLKOUT↓
—
—
—
—
—
75
75
35
35
—
—
—
50
—
—
—
10
—
10
—
—
—
200
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
TosH2ckH OSC1↑ to CLKOUT↑
200
TckR
CLKOUT rise time
100
TckF
CLKOUT fall time
100
TckL2ioV
TioV2ckH
TckH2ioI
TosH2ioV
TosH2ioI
CLKOUT ↓ to Port out valid
Port in valid before CLKOUT ↑
Port in hold after CLKOUT ↑
OSC1↑ (Q1 cycle) to Port out valid
0.5TCY + 20
0.25TCY + 25
—
—
0
—
150
—
OSC1↑ (Q2 cycle) to Port
input invalid (I/O in hold time)
PIC16C65
PIC16LC65
100
200
0
—
19*
20*
TioV2osH
TioR
Port input valid to OSC1↑ (I/O in setup time)
—
Port output rise time
PIC16C65
PIC16LC65
PIC16C65
PIC16LC65
—
25
60
25
60
—
—
21*
TioF
Port output fall time
—
—
22††*
23††*
Tinp
Trbp
RB0/INT pin high or low time
TCY
TCY
RB7:RB4 change int high or low time
—
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
†† These parameters are asynchronous events not related to any internal clock edge.
Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
DS30234D-page 222
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 20-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
OSC
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O Pins
Note: Refer to Figure 20-1 for load conditions.
TABLE 20-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max Units
Conditions
30*
31*
TmcL MCLR Pulse Width (low)
100
7
—
—
ns
VDD = 5V, -40˚C to +85˚C
VDD = 5V, -40˚C to +85˚C
Twdt
Watchdog Timer Time-out Period
18
33
ms
(No Prescaler)
32
Tost
Oscillation Start-up Timer Period
—
1024TOSC
72
—
—
TOSC = OSC1 period
33*
Tpwrt Power-up Timer Period or WDT
reset
28
132
ms
VDD = 5V, -40˚C to +85˚C
34
TIOZ
I/O Hi-impedance from MCLR Low
—
—
100
ns
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 223
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 20-5: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
RA4/T0CKI
41
46
40
45
42
47
RC0/T1OSO/T1CKI
48
TMR0 or
TMR1
Note: Refer to Figure 20-1 for load conditions.
TABLE 20-5: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Param
No.
Sym
Characteristic
Min
Typ† Max Units Conditions
40*
Tt0H
T0CKI High Pulse Width
No Prescaler
0.5TCY + 20
—
—
ns Must also meet
parameter 42
With Prescaler
No Prescaler
10
0.5TCY + 20
10
—
—
—
—
—
—
—
—
—
—
ns
41*
42*
Tt0L
Tt0P
T0CKI Low Pulse Width
T0CKI Period
ns Must also meet
parameter 42
With Prescaler
No Prescaler
With Prescaler
ns
ns
TCY + 40
Greater of:
20 or TCY + 40
ns N = prescale value
(2, 4, ..., 256)
N
0.5TCY + 20
15
45*
46*
47*
Tt1H
Tt1L
Tt1P
T1CKI High Time Synchronous, Prescaler = 1
—
—
—
—
—
—
ns Must also meet
parameter 47
Synchronous, PIC16C6X
ns
ns
Prescaler =
2,4,8
PIC16LC6X
25
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
—
—
—
—
ns
ns
50
T1CKI Low Time
Synchronous, Prescaler = 1
Synchronous, PIC16C6X
0.5TCY + 20
ns Must also meet
parameter 47
15
25
ns
ns
Prescaler =
2,4,8
PIC16LC6X
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
ns
ns
50
T1CKI input period Synchronous PIC16C6X
Greater of:
30 OR TCY + 40
ns N = prescale value
(1, 2, 4, 8)
N
Greater of:
50 OR TCY + 40
N = prescale value
(1, 2, 4, 8)
PIC16LC6X
N
60
Asynchronous PIC16C6X
PIC16LC6X
—
—
—
—
—
ns
ns
100
DC
Ft1
Timer1 oscillator input frequency range
(oscillator enabled by setting bit T1OSCEN)
200
kHz
48
*
TCKEZtmr1 Delay from external clock edge to timer increment
2Tosc
—
7Tosc
—
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 224
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 20-6: CAPTURE/COMPARE/PWM TIMINGS (CCP1 AND CCP2)
RC1/T1OSI/CCP2
and RC2/CCP1
(Capture Mode)
50
51
52
54
RC1/T1OSI/CCP2
and RC2/CCP1
(Compare or
PWM Mode)
53
Note: Refer to Figure 20-1 for load conditions.
TABLE 20-6: CAPTURE/COMPARE/PWM REQUIREMENTS (CCP1 AND CCP2)
Parameter Sym Characteristic
No.
Min
Typ† Max Units Conditions
50*
TccL CCP1 and CCP2 No Prescaler
input low time
0.5TCY + 20
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
With Prescaler PIC16C65
10
PIC16LC65
20
51*
TccH
No Prescaler
0.5TCY + 20
CCP1 and CCP2
input high time
With Prescaler PIC16C65
PIC16LC65
10
20
52*
53
TccP
3TCY + 40
N
ns N = prescale value
(1,4, or 16)
CCP1 and CCP2 input period
TccR CCP1 and CCP2 output rise time
TccF CCP1 and CCP2 output fall time
PIC16C65
PIC16LC65
PIC16C65
PIC16LC65
—
—
—
—
10
25
10
25
25
45
25
45
ns
ns
ns
ns
54
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 225
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 20-7: PARALLEL SLAVE PORT TIMING
RE2/CS
RE0/RD
RE1/WR
65
RD7:RD0
62
64
63
Note: Refer to Figure 20-1 for load conditions
TABLE 20-7: PARALLEL SLAVE PORT REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
62
TdtV2wrH Data in valid before WR↑ or CS↑ (setup time)
20
20
35
—
10
—
—
—
—
—
—
—
—
80
30
ns
ns
ns
ns
ns
63*
TwrH2dtI WR↑ or CS↑ to data–in invalid (hold
PIC16C65
PIC16LC65
time)
64
65
TrdL2dtV RD↓ and CS↓ to data–out valid
TrdH2dtI RD↑ or CS↑ to data–out invalid
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 226
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 20-8: SPI MODE TIMING
SS
70
SCK
(CKP = 0)
71
72
78
79
79
78
SCK
(CKP = 1)
80
SDO
SDI
77
75, 76
74
73
Note: Refer to Figure 20-1 for load conditions
TABLE 20-8: SPI MODE REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
70
TssL2scH,
TssL2scL
SS↓ to SCK↓ or SCK↑ input
TCY
—
—
ns
71
72
73
TscH
TscL
SCK input high time (slave mode)
SCK input low time (slave mode)
TCY + 20
TCY + 20
50
—
—
—
—
—
—
ns
ns
ns
TdiV2scH,
TdiV2scL
Setup time of SDI data input to SCK
edge
74
TscH2diL,
TscL2diL
Hold time of SDI data input to SCK
edge
50
—
—
ns
75
76
77
78
79
80
TdoR
SDO data output rise time
—
—
10
—
—
—
10
10
—
10
10
—
25
25
50
25
25
50
ns
ns
ns
ns
ns
ns
TdoF
SDO data output fall time
TssH2doZ
TscR
SS↑ to SDO output hi-impedance
SCK output rise time (master mode)
SCK output fall time (master mode)
TscF
TscH2doV,
TscL2doV
SDO data output valid after SCK
edge
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 227
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 20-9: I C BUS START/STOP BITS TIMING
SCL
91
93
92
90
SDA
STOP
Condition
START
Condition
Note: Refer to Figure 20-1 for load conditions
2
TABLE 20-9: I C BUS START/STOP BITS REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min Typ Max Units
Conditions
90
91
92
93
TSU:STA START condition
Setup time
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
4700
600
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Only relevant for repeated START
condition
ns
ns
ns
ns
THD:STA START condition
Hold time
4000
600
After this period the first clock
pulse is generated
TSU:STO STOP condition
Setup time
4700
600
THD:STO STOP condition
Hold time
4000
600
DS30234D-page 228
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 20-10: I C BUS DATA TIMING
103
102
100
101
106
SCL
90
107
91
92
SDA
In
110
109
109
SDA
Out
Note: Refer to Figure 20-1 for load conditions
2
TABLE 20-10: I C BUS DATA REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Max
Units
Conditions
100
THIGH
Clock high time
100 kHz mode
4.0
0.6
—
—
µs
µs
Device must operate at a min-
imum of 1.5 MHz
400 kHz mode
Devce must operate at a mini-
mum of 10 MHz
SSP Module
1.5TCY
4.7
—
—
101
TLOW
Clock low time
100 kHz mode
µs
µs
Device must operate at a min-
imum of 1.5 MHz
400 kHz mode
1.3
—
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
—
—
102
103
TR
TF
SDA and SCL rise
time
100 kHz mode
400 kHz mode
1000
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10-400 pF
SDA and SCL fall time 100 kHz mode
400 kHz mode
—
300
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10-400 pF
90
91
TSU:STA START condition
setup time
100 kHz mode
400 kHz mode
4.7
0.6
4.0
0.6
0
—
—
µs
µs
µs
µs
ns
µs
ns
ns
µs
µs
ns
ns
µs
µs
Only relevant for repeated
START condition
THD:STA START condition hold 100 kHz mode
—
After this period the first clock
pulse is generated
time
400 kHz mode
100 kHz mode
400 kHz mode
—
106
107
92
THD:DAT Data input hold time
—
0
0.9
—
TSU:DAT Data input setup time 100 kHz mode
400 kHz mode
250
100
4.7
0.6
—
Note 2
—
TSU:STO STOP condition setup 100 kHz mode
—
time
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
—
109
110
TAA
Output valid from
clock
3500
—
Note 1
—
TBUF
Bus free time
4.7
1.3
—
Time the bus must be free
before a new transmission
can start
—
Cb
Bus capacitive loading
—
400
pF
Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of
the falling edge of SCL to avoid unintended generation of START or STOP conditions.
2
2
2: A fast-mode (400 kHz) I C-bus device can be used in a standard-mode (100 kHz) I C-bus system, but the requirement
tsu;DAT ≥ 250 ns must then be met.This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line
2
TR max.+tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I C bus specification) before the SCL line is
released.
1997 Microchip Technology Inc.
DS30234D-page 229
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 20-11: USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
RC6/TX/CK
121
pin
121
RC7/RX/DT
pin
120
122
Note: Refer to Figure 20-1 for load conditions
TABLE 20-11: USART SYNCHRONOUS TRANSMISSION REQUIREMENTS
Parameter Sym
No.
Characteristic
Min
Typ†
Max
Units Conditions
120
121
122
TckH2dtV SYNC XMIT (MASTER & SLAVE)
Clock high to data out valid
PIC16C65
PIC16LC65
PIC16C65
PIC16LC65
PIC16C65
PIC16LC65
—
—
—
—
—
—
—
—
—
—
—
—
80
100
45
ns
ns
ns
ns
ns
ns
Tckrf
Clock out rise time and fall time
(Master Mode)
50
Tdtrf
Data out rise time and fall time
45
50
†:
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
FIGURE 20-12: USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
RC6/TX/CK
125
pin
RC7/RX/DT
pin
126
Note: Refer to Figure 20-1 for load conditions
TABLE 20-12: USART SYNCHRONOUS RECEIVE REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units Conditions
125
TdtV2ckL
SYNC RCV (MASTER & SLAVE)
Data setup before CK ↓ (DT setup time)
15
15
—
—
—
—
ns
ns
126
TckL2dtl
Data hold after CK ↓ (DT hold time)
†:
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 230
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
21.0 ELECTRICAL CHARACTERISTICS FOR PIC16C63/65A
(†)
Absolute Maximum Ratings
Ambient temperature under bias..............................................................................................................-55˚C to +125˚C
Storage temperature............................................................................................................................... -65˚C to +150˚C
Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4) ..........................................-0.3V to (VDD + 0.3V)
Voltage on VDD with respect to VSS .......................................................................................................... -0.3V to +7.5V
Voltage on MCLR with respect to VSS (Note 2) ...............................................................................................0V to +14V
Voltage on RA4 with respect to Vss.................................................................................................................0V to +14V
Total power dissipation (Note 1).................................................................................................................................1.0W
Maximum current out of VSS pin ............................................................................................................................300 mA
Maximum current into VDD pin...............................................................................................................................250 mA
Input clamp current, IIK (VI < 0 or VI > VDD) ......................................................................................................................±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD)...............................................................................................................±20 mA
Maximum output current sunk by any I/O pin...........................................................................................................25 mA
Maximum output current sourced by any I/O pin .....................................................................................................25 mA
Maximum current sunk by PORTA, PORTB, and PORTE (Note 3) (combined).....................................................200 mA
Maximum current sourced by PORTA, PORTB, and PORTE (Note 3) (combined) ...............................................200 mA
Maximum current sunk by PORTC and PORTD(Note 3) (combined) ...................................................................200 mA
Maximum current sourced by PORTC and PORTD(Note 3) (combined) ..............................................................200 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOl x IOL)
Note 2: Voltage spikes below VSS at the MCLR/VPP pin, inducing currents greater than 80 mA, may cause latch-up.
Thus, a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR/VPP pin rather
than pulling this pin directly to VSS.
Note 3: PORTD and PORTE not available on the PIC16C63.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 21-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16C63-04
PIC16C65A-04
PIC16C63-10
PIC16C65A-10
PIC16C63-20
PIC16C65A-20
PIC16LC63-04
PIC16LC65A-04
OSC
JW Devices
RC
VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 2.5V to 6.0V
VDD: 4.0V to 6.0V
IDD: 5 mA max. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 3.8 mA max. at 3V IDD: 5 mA max. at 5.5V
IPD: 16 µA max. at 4V IPD: 1.5 µA typ. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 5 µA max. at 3V
IPD: 16 µA max. at 4V
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
XT
HS
VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 2.5V to 6.0V
VDD: 4.0V to 6.0V
IDD: 5 mA max. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 3.8 mA max. at 3V IDD: 5 mA max. at 5.5V
IPD: 16 µA max. at 4V IPD: 1.5 µA typ. at 4V
Freq: 4 MHz max.
IPD: 1.5 µA typ. at 4V
Freq: 4 MHz max.
IPD: 5 µA max. at 3V
Freq: 4 MHz max.
IPD: 16 µA max. at 4V
Freq: 4 MHz max.
Freq: 4 MHz max.
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 13.5 mA typ. at
5.5V
IDD: 10 mA max. at 5.5V IDD: 20 mA max. at 5.5V
IDD: 20 mA max. at
5.5V
Not recommended for
use in HS mode
IPD: 1.5 µA typ. at 4.5V IPD 1.5 µA typ. at 4.5V IPD: 1.5 µA typ. at 4.5V
IPD: 1.5 µA typ. at 4.5V
Freq: 20 MHz max.
VDD: 2.5V to 6.0V
Freq: 4 MHz max.
Freq: 10 MHz max.
Freq: 20 MHz max.
LP
VDD: 4.0V to 6.0V
IDD: 52.5 µA typ.
at 32 kHz, 4.0V
IPD: 0.9 µA typ. at 4.0V
Freq: 200 kHz max.
VDD: 2.5V to 6.0V
IDD: 48 µA max. at 32 IDD: 48 µA max.
at 32 kHz, 3.0V
IPD: 5 µA max. at 3.0V IPD: 5 µA max. at 3.0V
Not recommended for
use in LP mode
Not recommended for
use in LP mode
kHz, 3.0V
Freq: 200 kHz max.
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifications. It is recom-
mended that the user select the device type that ensures the specifications required.
1997 Microchip Technology Inc.
DS30234D-page 231
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
21.1
DC Characteristics:
PIC16C63/65A-04 (Commercial, Industrial, Extended)
PIC16C63/65A-10 (Commercial, Industrial, Extended)
PIC16C63/65A-20 (Commercial, Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40˚C ≤ TA ≤ +125˚C for extended,
DC CHARACTERISTICS
-40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym
VDD
Min Typ† Max Units
Conditions
D001 Supply Voltage
D001A
4.0
4.5
-
-
6.0
5.5
V
V
XT, RC and LP osc configuration
HS osc configuration
D002* RAM Data Retention
Voltage (Note 1)
VDR
-
1.5
-
V
D003 VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
-
VSS
-
V
See section on Power-on Reset for details
D004* VDD rise rate to ensure
internal Power-on Reset
signal
SVDD
BVDD
0.05
-
-
V/ms See section on Power-on Reset for details
D005 Brown-out Reset Voltage
3.7
3.7
-
4.0 4.3
4.0 4.4
V
V
BODEN configuration bit is enabled
Extended Range Only
D010 Supply Current (Note 2, 5) IDD
D013
2.7
5
mA XT, RC, osc config FOSC = 4 MHz,
VDD = 5.5V (Note 4)
-
-
10
20
mA HS osc config FOSC = 20 MHz, VDD = 5.5V
D015* Brown-out Reset Current ∆IBOR
350 425 µA BOR enabled, VDD = 5.0V
(Note 6)
D020 Power-down Current
D021 (Note 3, 5)
D021A
IPD
-
-
-
-
10.5 42 µA VDD = 4.0V, WDT enabled,-40°C to +85°C
1.5
1.5
2.5
16
19
19
µA VDD = 4.0V, WDT disabled,-0°C to +70°C
µA VDD = 4.0V, WDT disabled,-40°C to +85°C
µA VDD = 4.0V, WDT disabled,-40°C to +125°C
D021B
D023* Brown-out Reset Current ∆IBOR
-
350 425 µA BOR enabled, VDD = 5.0V
(Note 6)
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated.These parameters are for design guidance only and
are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,
MCLR = VDD; WDT enabled/disabled as specified.
3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from character-
ization and is for design guidance only. This is not tested.
6: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be
added to the base IDD or IPD measurement.
DS30234D-page 232
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
21.2
DC Characteristics: PIC16LC63/65A-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature -40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym Min Typ† Max Units
Conditions
D001
Supply Voltage
VDD
VDR
2.5
-
-
6.0
-
V
V
LP, XT, RC osc configuration (DC - 4 MHz)
D002*
RAM Data Retention
Voltage (Note 1)
1.5
D003
VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
SVDD
BVDD
-
VSS
-
-
-
V
See section on Power-on Reset for details
D004*
VDD rise rate to ensure
internal Power-on Reset
signal
0.05
V/ms See section on Power-on Reset for details
D005
D010
Brown-out Reset Voltage
3.7
-
4.0
2.0
4.3
3.8
V
BODEN configuration bit is enabled
Supply Current (Note 2, 5) IDD
mA XT, RC osc configuration
FOSC = 4 MHz, VDD = 3.0V (Note 4)
D010A
D015*
-
-
22.5 48
350 425
µA LP osc configuration
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
Brown-out Reset Current ∆IBOR
µA BOR enabled, VDD = 5.0V
(Note 6)
D020
D021
D021A
Power-down Current
(Note 3, 5)
IPD
-
-
-
7.5
0.9
0.9
30
5
5
µA VDD = 3.0V, WDT enabled, -40°C to +85°C
µA VDD = 3.0V, WDT disabled, 0°C to +70°C
µA VDD = 3.0V, WDT disabled, -40°C to +85°C
D023*
Brown-out Reset Current ∆IBOR
-
350 425
µA BOR enabled, VDD = 5.0V
(Note 6)
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from character-
ization and is for design guidance only. This is not tested.
6: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be
added to the base IDD or IPD measurement.
1997 Microchip Technology Inc.
DS30234D-page 233
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
21.3
DC Characteristics:
PIC16C63/65A-04 (Commercial, Industrial, Extended)
PIC16C63/65A-10 (Commercial, Industrial, Extended)
PIC16C63/65A-20 (Commercial, Industrial, Extended)
PIC16LC63/65A-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +125˚C for extended,
-40˚C ≤ TA ≤ +85˚C for industrial and
DC CHARACTERISTICS
0˚C
≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in DC spec Section 21.1 and
Section 21.2
Param
No.
Characteristic
Sym
Min Typ Max
†
Units
Conditions
Input Low Voltage
I/O ports
VIL
D030
D030A
D031
D032
D033
with TTL buffer
VSS
VSS
VSS
Vss
Vss
-
-
-
-
-
0.15VDD
0.8V
0.2VDD
0.2VDD
0.3VDD
V
V
V
V
V
For entire VDD range
4.5V ≤ VDD ≤ 5.5V
with Schmitt Trigger buffer
MCLR, OSC1 (in RC mode)
OSC1 (in XT, HS and LP)
Input High Voltage
I/O ports
Note1
VIH
-
-
-
D040
D040A
with TTL buffer
2.0
0.25VDD
+ 0.8V
VDD
VDD
V
V
4.5V ≤ VDD ≤ 5.5V
For entire VDD range
D041
D042
with Schmitt Trigger buffer
MCLR
0.8VDD
0.8VDD
0.7VDD
0.9VDD
50
-
-
-
-
VDD
VDD
VDD
VDD
400
V
V
V
V
For entire VDD range
Note1
D042A OSC1 (XT, HS and LP)
D043
D070
OSC1 (in RC mode)
PORTB weak pull-up current
Input Leakage Current (Notes 2, 3)
I/O ports
IPURB
IIL
250
µA VDD = 5V, VPIN = VSS
D060
-
-
±1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
D061
D063
MCLR, RA4/T0CKI
OSC1
-
-
-
-
±5
±5
µA Vss ≤ VPIN ≤ VDD
µA Vss ≤ VPIN ≤ VDD, XT, HS and
LP osc configuration
Output Low Voltage
D080
I/O ports
VOL
-
-
-
-
-
-
-
-
0.6
0.6
0.6
0.6
V
V
V
V
IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 7.0 mA, VDD = 4.5V,
-40°C to +125°C
IOL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 1.2 mA, VDD = 4.5V,
-40°C to +125°C
D080A
D083
OSC2/CLKOUT (RC osc config)
D083A
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
DS30234D-page 234
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +125˚C for extended,
-40˚C ≤ TA ≤ +85˚C for industrial and
DC CHARACTERISTICS
0˚C
≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in DC spec Section 21.1 and
Section 21.2
Param
No.
Characteristic
Sym
Min Typ Max
†
Units
Conditions
Output High Voltage
D090
I/O ports (Note 3)
VOH
VDD-0.7
VDD-0.7
VDD-0.7
VDD-0.7
-
-
-
-
-
-
-
-
V
V
V
V
V
IOH = -3.0 mA, VDD = 4.5V,
-40°C to +85°C
IOH = -2.5 mA, VDD = 4.5V,
-40°C to +125°C
IOH = -1.3 mA, VDD = 4.5V,
-40°C to +85°C
IOH = -1.0 mA, VDD = 4.5V,
-40°C to +125°C
D090A
D092
OSC2/CLKOUT (RC osc config)
-
D092A
-
D150* Open-Drain High Voltage
Capacitive Loading Specs on Out-
VOD
14
RA4 pin
put Pins
D100
OSC2 pin
COSC2
-
-
15
pF In XT, HS and LP modes when
external clock is used to drive
OSC1.
D101
D102
All I/O pins and OSC2 (in RC mode) CIO
-
-
-
-
50
400
pF
pF
2
Cb
SCL, SDA in I C mode
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
1997 Microchip Technology Inc.
DS30234D-page 235
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
21.4
Timing Parameter Symbology
The timing parameter symbols have been created following one of the following formats:
2
1. TppS2ppS
2. TppS
3. TCC:ST
4. Ts
(I C specifications only)
2
(I C specifications only)
T
F
Frequency
T
Time
Lowercase letters (pp) and their meanings:
pp
cc
CCP1
CLKOUT
CS
osc
rd
OSC1
RD
ck
cs
di
rw
sc
ss
t0
RD or WR
SCK
SDI
do
dt
SDO
SS
Data in
I/O port
MCLR
T0CKI
T1CKI
WR
io
t1
mc
wr
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
2
I C only
AA
output access
Bus free
High
Low
High
Low
BUF
2
TCC:ST (I C specifications only)
CC
HD
ST
DAT
STA
Hold
SU
Setup
DATA input hold
START condition
STO
STOP condition
FIGURE 21-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load condition 1
Load condition 2
VDD/2
CL
RL
Pin
VSS
CL
Pin
RL = 464Ω
CL = 50 pF for all pins except OSC2/CLKOUT
but including D and E outputs as ports
VSS
Note 1: PORTD and PORTE are not imple-
mented on the PIC16C63.
15 pF for OSC2 output
DS30234D-page 236
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
21.5
Timing Diagrams and Specifications
FIGURE 21-2: EXTERNAL CLOCK TIMING
Q1
1
Q2
Q3
Q4
4
Q4
Q1
OSC1
3
3
4
2
CLKOUT
TABLE 21-2: EXTERNAL CLOCK TIMING REQUIREMENTS
Param
No.
Sym Characteristic
Min
Typ†
Max
Units Conditions
Fosc External CLKIN Frequency
DC
DC
DC
DC
DC
DC
0.1
4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TCY
—
—
—
—
—
—
4
4
MHz XT and RC osc mode
MHz HS osc mode (-04)
MHz HS osc mode (-10)
MHz HS osc mode (-20)
kHz LP osc mode
(Note 1)
10
20
200
4
Oscillator Frequency
(Note 1)
MHz RC osc mode
4
MHz XT osc mode
20
200
—
MHz HS osc mode
5
kHz LP osc mode
1
Tosc External CLKIN Period
250
250
100
50
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
ns
ns
µs
ns
ns
ns
ns
XT and RC osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
(Note 1)
—
—
—
5
—
Oscillator Period
(Note 1)
250
250
250
100
50
—
RC osc mode
10,000
250
250
250
—
XT osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
5
2
TCY
Instruction Cycle Time (Note 1)
200
100
2.5
15
DC
—
TCY = 4/FOSC
3*
TosL, External Clock in (OSC1) High or
TosH Low Time
XT oscillator
—
LP oscillator
—
HS oscillator
4*
TosR, External Clock in (OSC1) Rise or
TosF Fall Time
—
25
50
15
XT oscillator
—
LP oscillator
—
HS oscillator
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin.
When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices.
1997 Microchip Technology Inc.
DS30234D-page 237
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 21-3: CLKOUT AND I/O TIMING
Q1
Q2
Q3
Q4
OSC1
11
10
CLKOUT
13
12
19
18
14
16
I/O Pin
(input)
15
17
I/O Pin
(output)
new value
old value
20, 21
Note: Refer to Figure 21-1 for load conditions.
TABLE 21-3: CLKOUT AND I/O TIMING REQUIREMENTS
Parameter Sym
No.
Characteristic
Min
Typ†
Max
Units Conditions
10*
11*
12*
13*
14*
15*
16*
17*
18*
TosH2ckL OSC1↑ to CLKOUT↓
TosH2ckH OSC1↑ to CLKOUT↑
—
75
75
35
35
—
—
—
50
—
—
—
10
—
10
—
—
—
200
200
100
100
ns
ns
ns
ns
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
—
TckR
TckF
CLKOUT rise time
CLKOUT fall time
—
—
TckL2ioV CLKOUT ↓ to Port out valid
TioV2ckH Port in valid before CLKOUT ↑
—
0.5TCY + 20 ns
Tosc + 200
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
TckH2ioI
TosH2ioV OSC1↑ (Q1 cycle) to Port out valid
TosH2ioI OSC1↑ (Q2 cycle) to Port input PIC16C63/65A
invalid (I/O in hold time)
TioV2osH Port input valid to OSC1↑ (I/O in setup time)
Port in hold after CLKOUT ↑
0
—
150
—
100
200
0
PIC16LC63/65A
—
19*
20*
—
TioR
Port output rise time
Port output fall time
INT pin high or low time
PIC16C63/65A
PIC16LC63/65A
PIC16C63/65A
PIC16LC63/65A
—
40
80
40
80
—
—
21*
TioF
—
—
22††*
23††*
Tinp
Trbp
TCY
TCY
RB7:RB4 change INT high or low time
—
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
†† These parameters are asynchronous events not related to any internal clock edge.
Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
DS30234D-page 238
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 21-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
OSC
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O Pins
Note: Refer to Figure 21-1 for load conditions.
FIGURE 21-5: BROWN-OUT RESET TIMING
BVDD
VDD
35
TABLE 21-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER,
AND BROWN-OUT RESET REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max Units
Conditions
30
TmcL MCLR Pulse Width (low)
2
7
—
—
µs VDD = 5V, -40˚C to +125˚C
31*
Twdt
Watchdog Timer Time-out Period
18
33
ms
VDD = 5V, -40˚C to +125˚C
(No Prescaler)
32
33*
34
Tost
Oscillation Start-up Timer Period
—
28
—
1024 TOSC
—
—
ms
µs
TOSC = OSC1 period
Tpwrt Power-up Timer Period
72
—
132
2.1
VDD = 5V, -40˚C to +125˚C
TIOZ
I/O Hi-impedance from MCLR Low
or WDT reset
35
TBOR
Brown-out Reset Pulse Width
100
—
—
VDD ≤ BVDD (D005)
µs
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 239
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 21-6: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
RA4/T0CKI
41
40
42
RC0/T1OSO/T1CKI
46
45
47
48
TMR0 or
TMR1
Note: Refer to Figure 21-1 for load conditions.
TABLE 21-5: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Param
No.
Sym
Characteristic
Min
Typ† Max Units Conditions
40*
Tt0H
T0CKI High Pulse Width
No Prescaler
0.5TCY + 20
—
—
ns Must also meet
parameter 42
With Prescaler
No Prescaler
10
0.5TCY + 20
10
—
—
—
—
—
—
—
—
—
—
ns
41*
42*
Tt0L
Tt0P
T0CKI Low Pulse Width
T0CKI Period
ns Must also meet
parameter 42
With Prescaler
No Prescaler
With Prescaler
ns
ns
TCY + 40
Greater of:
20 or TCY + 40
ns N = prescale value
(2, 4, ..., 256)
N
0.5TCY + 20
15
45*
46*
47*
Tt1H
Tt1L
Tt1P
T1CKI High Time Synchronous, Prescaler = 1
—
—
—
—
—
—
ns Must also meet
parameter 47
Synchronous, PIC16C6X
ns
ns
Prescaler =
2,4,8
PIC16LC6X
25
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
—
—
—
—
ns
ns
50
T1CKI Low Time
Synchronous, Prescaler = 1
Synchronous, PIC16C6X
0.5TCY + 20
ns Must also meet
parameter 47
15
25
ns
ns
Prescaler =
2,4,8
PIC16LC6X
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
ns
ns
50
T1CKI input period Synchronous PIC16C6X
Greater of:
30 OR TCY + 40
ns N = prescale value
(1, 2, 4, 8)
N
PIC16LC6X
Greater of:
50 OR TCY + 40
N = prescale value
(1, 2, 4, 8)
N
60
Asynchronous PIC16C6X
PIC16LC6X
—
—
—
—
—
ns
ns
100
DC
Ft1
Timer1 oscillator input frequency range
(oscillator enabled by setting bit T1OSCEN)
200
kHz
48
*
TCKEZtmr1 Delay from external clock edge to timer increment
2Tosc
—
7Tosc
—
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 240
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 21-7: CAPTURE/COMPARE/PWM TIMINGS (CCP1 AND CCP2)
RC1/T1OSI/CCP2
and RC2/CCP1
(Capture Mode)
50
51
52
54
RC1/T1OSI/CCP2
and RC2/CCP1
(Compare or
PWM Mode)
53
Note: Refer to Figure 21-1 for load conditions.
TABLE 21-6: CAPTURE/COMPARE/PWM REQUIREMENTS (CCP1 AND CCP2)
Parameter Sym Characteristic
No.
Min
Typ† Max Units Conditions
50*
TccL CCP1 and CCP2 No Prescaler
input low time
0.5TCY + 20
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
With Prescaler PIC16C63/65A
10
PIC16LC63/65A
20
51*
TccH
No Prescaler
0.5TCY + 20
CCP1 and CCP2
input high time
With Prescaler PIC16C63/65A
PIC16LC63/65A
10
20
52*
53*
TccP
3TCY + 40
N
ns N = prescale value
(1,4, or 16)
CCP1 and CCP2 input period
TccR CCP1 and CCP2 output rise time
TccF CCP1 and CCP2 output fall time
PIC16C63/65A
PIC16LC63/65A
PIC16C63/65A
PIC16LC63/65A
—
—
—
—
10
25
10
25
25
45
25
45
ns
ns
ns
ns
54*
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 241
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 21-8: PARALLEL SLAVE PORT TIMING (PIC16C65A)
RE2/CS
RE0/RD
RE1/WR
65
RD7:RD0
62
64
63
Note: Refer to Figure 21-1 for load conditions
TABLE 21-7: PARALLEL SLAVE PORT REQUIREMENTS (PIC16C65A)
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units Conditions
62*
TdtV2wrH Data in valid before WR↑ or CS↑ (setup time)
20
25
—
—
—
—
ns
ns
Extended
Range Only
63*
64
TwrH2dtI WR↑ or CS↑ to data–in invalid (hold
PIC16C65A
PIC16LC65A
20
35
—
—
—
—
—
—
—
—
80
90
ns
ns
ns
ns
time)
TrdL2dtV RD↓ and CS↓ to data–out valid
Extended
Range Only
65*
TrdH2dtI RD↑ or CS↑ to data–out invalid
10
—
30
ns
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 242
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 21-9: SPI MODE TIMING
SS
70
SCK
(CKP = 0)
71
72
78
79
79
78
SCK
(CKP = 1)
80
SDO
SDI
77
75, 76
74
73
Note: Refer to Figure 21-1 for load conditions
TABLE 21-8: SPI MODE REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
70*
TssL2scH,
TssL2scL
SS↓ to SCK↓ or SCK↑ input
TCY
—
—
ns
71*
72*
73*
TscH
TscL
SCK input high time (slave mode)
SCK input low time (slave mode)
TCY + 20
TCY + 20
50
—
—
—
—
—
—
ns
ns
ns
TdiV2scH,
TdiV2scL
Setup time of SDI data input to SCK
edge
74*
TscH2diL,
TscL2diL
Hold time of SDI data input to SCK
edge
50
—
—
ns
75*
76*
77*
78*
79*
80*
TdoR
SDO data output rise time
—
—
10
—
—
—
10
10
—
10
10
—
25
25
50
25
25
50
ns
ns
ns
ns
ns
ns
TdoF
SDO data output fall time
TssH2doZ
TscR
SS↑ to SDO output hi-impedance
SCK output rise time (master mode)
SCK output fall time (master mode)
TscF
TscH2doV,
TscL2doV
SDO data output valid after SCK
edge
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 243
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 21-10: I C BUS START/STOP BITS TIMING
SCL
91
93
90
92
SDA
STOP
Condition
START
Condition
Note: Refer to Figure 21-1 for load conditions
2
TABLE 21-9: I C BUS START/STOP BITS REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min Typ Max Units
Conditions
90*
91*
92*
93
TSU:STA START condition
Setup time
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
4700
600
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Only relevant for repeated START
condition
ns
ns
ns
ns
THD:STA START condition
Hold time
4000
600
After this period the first clock
pulse is generated
TSU:STO STOP condition
Setup time
4700
600
THD:STO STOP condition
Hold time
4000
600
*
These parameters are characterized but not tested.
DS30234D-page 244
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 21-11: I C BUS DATA TIMING
103
102
100
101
SCL
90
106
107
91
92
SDA
In
110
109
109
SDA
Out
Note: Refer to Figure 21-1 for load conditions
2
TABLE 21-10: I C BUS DATA REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Max
Units
Conditions
100*
THIGH
Clock high time
100 kHz mode
400 kHz mode
4.0
0.6
—
—
µs
µs
Device must operate at a min-
imum of 1.5 MHz
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
4.7
—
—
101*
TLOW
Clock low time
100 kHz mode
µs
µs
Device must operate at a min-
imum of 1.5 MHz
400 kHz mode
1.3
—
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
—
—
102*
103*
TR
TF
SDA and SCL rise
time
100 kHz mode
400 kHz mode
1000
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10-400 pF
SDA and SCL fall time 100 kHz mode
400 kHz mode
—
300
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10-400 pF
90*
91*
TSU:STA START condition
setup time
100 kHz mode
400 kHz mode
4.7
0.6
4.0
0.6
0
—
—
µs
µs
µs
µs
ns
µs
ns
ns
µs
µs
ns
ns
µs
µs
Only relevant for repeated
START condition
THD:STA START condition hold 100 kHz mode
—
After this period the first clock
pulse is generated
time
400 kHz mode
100 kHz mode
400 kHz mode
—
106*
107*
92*
THD:DAT Data input hold time
—
0
0.9
—
TSU:DAT Data input setup time 100 kHz mode
400 kHz mode
250
100
4.7
0.6
—
Note 2
—
TSU:STO STOP condition setup 100 kHz mode
—
time
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
—
109*
110*
TAA
Output valid from
clock
3500
—
Note 1
—
TBUF
Bus free time
4.7
1.3
—
Time the bus must be free
before a new transmission can
start
—
Cb
Bus capacitive loading
—
400
pF
*
These parameters are characterized but not tested.
Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of
the falling edge of SCL to avoid unintended generation of START or STOP conditions.
2
2
2: A fast-mode (400 kHz) I C-bus device can be used in a standard-mode (100 kHz) I C-bus system, but the requirement
Tsu:DAT ≥ 250 ns must then be met.This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line
2
TR max.+tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I C bus specification) before the SCL line is
released.
1997 Microchip Technology Inc.
DS30234D-page 245
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 21-12: USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
RC6/TX/CK
pin
121
121
RC7/RX/DT
pin
120
122
Note: Refer to Figure 21-1 for load conditions
TABLE 21-11: USART SYNCHRONOUS TRANSMISSION REQUIREMENTS
Parameter Sym
No.
Characteristic
Min
Typ†
Max
Units Conditions
120*
121*
122*
TckH2dtV
SYNC XMIT (MASTER & SLAVE) PIC16C63/65A
—
—
—
—
—
—
—
—
—
—
—
—
80
100
45
ns
ns
ns
ns
ns
ns
Clock high to data out valid
PIC16LC63/65A
Tckrf
Tdtrf
Clock out rise time and fall time
(Master Mode)
PIC16C63/65A
PIC16LC63/65A
PIC16C63/65A
PIC16LC63/65A
50
Data out rise time and fall time
45
50
*
These parameters are characterized but not tested.
†:
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
FIGURE 21-13: USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
RC6/TX/CK
125
pin
RC7/RX/DT
pin
126
Note: Refer to Figure 21-1 for load conditions
TABLE 21-12: USART SYNCHRONOUS RECEIVE REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units Conditions
125*
TdtV2ckL
TckL2dtl
SYNC RCV (MASTER & SLAVE)
Data setup before CK ↓ (DT setup time)
15
15
—
—
—
—
ns
ns
126*
Data hold after CK ↓ (DT hold time)
*
These parameters are characterized but not tested.
†:
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 246
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
22.0 ELECTRICAL CHARACTERISTICS FOR PIC16CR63/R65
(†)
Absolute Maximum Ratings
Ambient temperature under bias..............................................................................................................-55˚C to +125˚C
Storage temperature............................................................................................................................... -65˚C to +150˚C
Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4) ..........................................-0.3V to (VDD + 0.3V)
Voltage on VDD with respect to VSS .......................................................................................................... -0.3V to +7.5V
Voltage on MCLR with respect to VSS (Note 2) ...............................................................................................0V to +14V
Voltage on RA4 with respect to Vss.................................................................................................................0V to +14V
Total power dissipation (Note 1).................................................................................................................................1.0W
Maximum current out of VSS pin ............................................................................................................................300 mA
Maximum current into VDD pin...............................................................................................................................250 mA
Input clamp current, IIK (VI < 0 or VI > VDD) ......................................................................................................................±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD)...............................................................................................................±20 mA
Maximum output current sunk by any I/O pin...........................................................................................................25 mA
Maximum output current sourced by any I/O pin .....................................................................................................25 mA
Maximum current sunk by PORTA, PORTB, and PORTE (Note 3) (combined).....................................................200 mA
Maximum current sourced by PORTA, PORTB, and PORTE (Note 3) (combined) ...............................................200 mA
Maximum current sunk by PORTC and PORTD(Note 3) (combined) ...................................................................200 mA
Maximum current sourced by PORTC and PORTD(Note 3) (combined) ..............................................................200 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOl x IOL)
Note 2: Voltage spikes below VSS at the MCLR/VPP pin, inducing currents greater than 80 mA, may cause latch-up.
Thus, a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR/VPP pin rather
than pulling this pin directly to VSS.
Note 3: PORTD and PORTE not available on the PIC16CR63.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 22-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16CR63-04
PIC16CR65-04
PIC16CR63-10
PIC16CR65-10
PIC16CR63-20
PIC16CR65-20
PIC16LCR63-04
PIC16LCR65-04
OSC
JW Devices
RC
VDD: 4.0V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 3.0V to 5.5V
VDD: 4.0V to 5.5V
IDD: 5 mA max. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 3.8 mA max. at 3V IDD: 5 mA max. at 5.5V
IPD: 16 µA max. at 4V IPD: 1.5 µA typ. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 5 µA max. at 3V
IPD: 16 µA max. at 4V
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
XT
HS
VDD: 4.0V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 3.0V to 5.5V
VDD: 4.0V to 5.5V
IDD: 5 mA max. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 3.8 mA max. at 3V IDD: 5 mA max. at 5.5V
IPD: 16 µA max. at 4V IPD: 1.5 µA typ. at 4V
Freq: 4 MHz max.
IPD: 1.5 µA typ. at 4V
Freq: 4 MHz max.
IPD: 5 µA max. at 3V
Freq: 4 MHz max.
IPD: 16 µA max. at 4V
Freq: 4 MHz max.
Freq: 4 MHz max.
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 13.5 mA typ. at
5.5V
IDD: 10 mA max. at 5.5V IDD: 20 mA max. at 5.5V
IDD: 20 mA max. at
5.5V
Not recommended for
use in HS mode
IPD: 1.5 µA typ. at 4.5V IPD 1.5 µA typ. at 4.5V IPD: 1.5 µA typ. at 4.5V
IPD: 1.5 µA typ. at 4.5V
Freq: 20 MHz max.
VDD: 3.0V to 5.5V
Freq: 4 MHz max.
Freq: 10 MHz max.
Freq: 20 MHz max.
LP
VDD: 4.0V to 5.5V
IDD: 52.5 µA typ.
at 32 kHz, 4.0V
IPD: 0.9 µA typ. at 4.0V
Freq: 200 kHz max.
VDD: 3.0V to 5.5V
IDD: 48 µA max. at 32 IDD: 48 µA max.
at 32 kHz, 3.0V
IPD: 5 µA max. at 3.0V IPD: 5 µA max. at 3.0V
Not recommended for
use in LP mode
Not recommended for
use in LP mode
kHz, 3.0V
Freq: 200 kHz max.
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifications. It is recom-
mended that the user select the device type that ensures the specifications required.
1997 Microchip Technology Inc.
Preliminary
DS30234D-page 247
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
22.1
DC Characteristics:
PIC16CR63/R65-04 (Commercial, Industrial)
PIC16CR63/R65-10 (Commercial, Industrial)
PIC16CR63/R65-20 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature -40˚C ≤ TA ≤ +85˚C for industrial and
0˚C
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym
VDD
Min Typ† Max Units
Conditions
D001 Supply Voltage
D001A
4.0
4.5
-
-
5.5
5.5
V
V
XT, RC and LP osc configuration
HS osc configuration
D002* RAM Data Retention
Voltage (Note 1)
VDR
-
1.5
-
V
D003 VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
-
VSS
-
V
See section on Power-on Reset for details
D004* VDD rise rate to ensure
internal Power-on Reset
signal
SVDD
BVDD
0.05
-
-
V/ms See section on Power-on Reset for details
D005 Brown-out Reset Voltage
3.7
-
4.0 4.3
V
BODEN configuration bit is enabled
D010 Supply Current (Note 2, 5) IDD
2.7
5
mA XT, RC, osc config FOSC = 4 MHz,
VDD = 5.5V (Note 4)
D013
-
-
10
20
mA HS osc config
FOSC = 20 MHz, VDD = 5.5V
D015* Brown-out Reset Current ∆IBOR
350 425 µA BOR enabled, VDD = 5.0V
(Note 6)
D020 Power-down Current
D021 (Note 3, 5)
D021A
IPD
-
-
-
10.5 42 µA VDD = 4.0V, WDT enabled,-40°C to +85°C
1.5
1.5
16
19
µA VDD = 4.0V, WDT disabled,-0°C to +70°C
µA VDD = 4.0V, WDT disabled,-40°C to +85°C
D023* Brown-out Reset Current ∆IBOR
-
350 425 µA BOR enabled, VDD = 5.0V
(Note 6)
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,
MCLR = VDD; WDT enabled/disabled as specified.
3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from character-
ization and is for design guidance only. This is not tested.
6: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be
added to the base IDD or IPD measurement.
DS30234D-page 248
Preliminary
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
22.2
DC Characteristics: PIC16LCR63/R65-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature -40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym Min Typ† Max Units
Conditions
D001
Supply Voltage
VDD
VDR
3.0
-
-
5.5
-
V
V
LP, XT, RC osc configuration (DC - 4 MHz)
D002*
RAM Data Retention
Voltage (Note 1)
1.5
D003
VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
SVDD
BVDD
-
VSS
-
-
-
V
See section on Power-on Reset for details
D004*
VDD rise rate to ensure
internal Power-on Reset
signal
0.05
V/ms See section on Power-on Reset for details
D005
D010
Brown-out Reset Voltage
3.7
-
4.0
2.0
4.3
3.8
V
BODEN configuration bit is enabled
Supply Current (Note 2, 5) IDD
mA XT, RC osc configuration
FOSC = 4 MHz, VDD = 3.0V (Note 4)
D010A
D015*
-
-
22.5 48
350 425
µA LP osc configuration
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
Brown-out Reset Current ∆IBOR
µA BOR enabled, VDD = 5.0V
(Note 6)
D020
D021
D021A
Power-down Current
(Note 3, 5)
IPD
-
-
-
7.5
0.9
0.9
30
5
5
µA VDD = 3.0V, WDT enabled, -40°C to +85°C
µA VDD = 3.0V, WDT disabled, 0°C to +70°C
µA VDD = 3.0V, WDT disabled, -40°C to +85°C
D023*
Brown-out Reset Current ∆IBOR
-
350 425
µA BOR enabled, VDD = 5.0V
(Note 6)
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from character-
ization and is for design guidance only. This is not tested.
6: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be
added to the base IDD or IPD measurement.
1997 Microchip Technology Inc.
Preliminary
DS30234D-page 249
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
22.3
DC Characteristics:
PIC16CR63/R65-04 (Commercial, Industrial)
PIC16CR63/R65-10 (Commercial, Industrial)
PIC16CR63/R65-20 (Commercial, Industrial)
PIC16LCR63/R65-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +85˚C for industrial and
0˚C ≤ TA ≤ +70˚C for commercial
DC CHARACTERISTICS
Operating voltage VDD range as described in DC spec Section 22.1 and
Section 22.2
Param
No.
Characteristic
Sym
Min Typ Max
†
Units
Conditions
Input Low Voltage
I/O ports
VIL
D030
D030A
D031
D032
D033
with TTL buffer
VSS
VSS
VSS
Vss
Vss
-
-
-
-
-
0.15VDD
0.8V
0.2VDD
0.2VDD
0.3VDD
V
V
V
V
V
For entire VDD range
4.5V ≤ VDD ≤ 5.5V
with Schmitt Trigger buffer
MCLR, OSC1 (in RC mode)
OSC1 (in XT, HS and LP)
Input High Voltage
I/O ports
Note1
VIH
-
-
-
D040
D040A
with TTL buffer
2.0
0.25VDD
+ 0.8V
VDD
VDD
V
V
4.5V ≤ VDD ≤ 5.5V
For entire VDD range
D041
D042
with Schmitt Trigger buffer
MCLR
0.8VDD
0.8VDD
0.7VDD
0.9VDD
50
-
-
-
-
VDD
VDD
VDD
VDD
400
V
V
V
V
For entire VDD range
Note1
D042A OSC1 (XT, HS and LP)
D043
D070
OSC1 (in RC mode)
PORTB weak pull-up current
Input Leakage Current (Notes 2, 3)
I/O ports
IPURB
IIL
250
µA VDD = 5V, VPIN = VSS
D060
-
-
±1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
D061
D063
MCLR, RA4/T0CKI
OSC1
-
-
-
-
±5
±5
µA Vss ≤ VPIN ≤ VDD
µA Vss ≤ VPIN ≤ VDD, XT, HS and
LP osc configuration
Output Low Voltage
D080
D083
I/O ports
VOL
-
-
-
-
0.6
0.6
V
V
IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
OSC2/CLKOUT (RC osc config)
Output High Voltage
D090
D092
I/O ports (Note 3)
VOH
VOD
VDD-0.7
VDD-0.7
-
-
-
-
-
-
V
V
V
IOH = -3.0 mA, VDD = 4.5V,
-40°C to +85°C
IOH = -1.3 mA, VDD = 4.5V,
-40°C to +85°C
OSC2/CLKOUT (RC osc config)
D150* Open-Drain High Voltage
14
RA4 pin
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
DS30234D-page 250
Preliminary
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +85˚C for industrial and
0˚C ≤ TA ≤ +70˚C for commercial
DC CHARACTERISTICS
Operating voltage VDD range as described in DC spec Section 22.1 and
Section 22.2
Param
No.
Characteristic
Sym
Min Typ Max
†
Units
Conditions
Capacitive Loading Specs on Out-
put Pins
D100
OSC2 pin
COSC2
-
-
15
pF In XT, HS and LP modes when
external clock is used to drive
OSC1.
D101
D102
All I/O pins and OSC2 (in RC mode) CIO
-
-
-
-
50
400
pF
pF
2
Cb
SCL, SDA in I C mode
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
1997 Microchip Technology Inc.
Preliminary
DS30234D-page 251
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
22.4
Timing Parameter Symbology
The timing parameter symbols have been created following one of the following formats:
2
1. TppS2ppS
2. TppS
3. TCC:ST
4. Ts
(I C specifications only)
2
(I C specifications only)
T
F
Frequency
T
Time
Lowercase letters (pp) and their meanings:
pp
cc
CCP1
CLKOUT
CS
osc
rd
OSC1
RD
ck
cs
di
rw
sc
ss
t0
RD or WR
SCK
SDI
do
dt
SDO
SS
Data in
I/O port
MCLR
T0CKI
T1CKI
WR
io
t1
mc
wr
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
2
I C only
AA
output access
Bus free
High
Low
High
Low
BUF
2
TCC:ST (I C specifications only)
CC
HD
ST
DAT
STA
Hold
SU
Setup
DATA input hold
START condition
STO
STOP condition
FIGURE 22-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load condition 1
Load condition 2
VDD/2
CL
RL
Pin
VSS
CL
Pin
RL = 464Ω
CL = 50 pF for all pins except OSC2/CLKOUT
but including D and E outputs as ports
VSS
Note 1: PORTD and PORTE are not imple-
mented on the PIC16CR63.
15 pF for OSC2 output
DS30234D-page 252
Preliminary
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
22.5
Timing Diagrams and Specifications
FIGURE 22-2: EXTERNAL CLOCK TIMING
Q1
1
Q2
Q3
Q4
4
Q4
Q1
OSC1
3
3
4
2
CLKOUT
TABLE 22-2: EXTERNAL CLOCK TIMING REQUIREMENTS
Param
No.
Sym Characteristic
Min
Typ†
Max
Units Conditions
Fosc External CLKIN Frequency
DC
DC
DC
DC
DC
DC
0.1
4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TCY
—
—
—
—
—
—
4
4
MHz XT and RC osc mode
MHz HS osc mode (-04)
MHz HS osc mode (-10)
MHz HS osc mode (-20)
kHz LP osc mode
(Note 1)
10
20
200
4
Oscillator Frequency
(Note 1)
MHz RC osc mode
4
MHz XT osc mode
20
200
—
MHz HS osc mode
5
kHz LP osc mode
1
Tosc External CLKIN Period
250
250
100
50
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
ns
ns
µs
ns
ns
ns
ns
XT and RC osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
(Note 1)
—
—
—
5
—
Oscillator Period
(Note 1)
250
250
250
100
50
—
RC osc mode
10,000
250
250
250
—
XT osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
5
2
TCY
Instruction Cycle Time (Note 1)
200
100
2.5
15
DC
—
TCY = 4/FOSC
3*
TosL, External Clock in (OSC1) High or
TosH Low Time
XT oscillator
—
LP oscillator
—
HS oscillator
4*
TosR, External Clock in (OSC1) Rise or
TosF Fall Time
—
25
50
15
XT oscillator
—
LP oscillator
—
HS oscillator
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin.
When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices.
1997 Microchip Technology Inc.
Preliminary
DS30234D-page 253
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 22-3: CLKOUT AND I/O TIMING
Q1
Q2
Q3
Q4
OSC1
11
10
CLKOUT
13
12
19
18
14
16
I/O Pin
(input)
15
17
I/O Pin
(output)
new value
old value
20, 21
Note: Refer to Figure 22-1 for load conditions.
TABLE 22-3: CLKOUT AND I/O TIMING REQUIREMENTS
Param Sym
No.
Characteristic
Min
Typ†
Max
Units Conditions
10*
11*
12*
13*
14*
15*
16*
17*
18*
TosH2ckL OSC1↑ to CLKOUT↓
TosH2ckH OSC1↑ to CLKOUT↑
—
75
75
35
35
—
—
—
50
—
—
—
10
—
10
—
—
—
200
200
100
100
ns
ns
ns
ns
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
—
TckR
TckF
CLKOUT rise time
CLKOUT fall time
—
—
TckL2ioV CLKOUT ↓ to Port out valid
TioV2ckH Port in valid before CLKOUT ↑
—
0.5TCY + 20 ns
Tosc + 200
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
TckH2ioI
TosH2ioV OSC1↑ (Q1 cycle) to Port out valid
TosH2ioI OSC1↑ (Q2 cycle) to Port input PIC16CR63/R65
invalid (I/O in hold time)
TioV2osH Port input valid to OSC1↑ (I/O in setup time)
Port in hold after CLKOUT ↑
0
—
150
—
100
200
0
PIC16LCR63/R65
—
19*
20*
—
TioR
Port output rise time
Port output fall time
INT pin high or low time
PIC16CR63/R65
PIC16LCR63/R65
PIC16CR63/R65
PIC16LCR63/R65
—
40
80
40
80
—
—
21*
TioF
—
—
22††* Tinp
23††* Trbp
TCY
TCY
RB7:RB4 change INT high or low time
—
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
†† These parameters are asynchronous events not related to any internal clock edge.
Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
DS30234D-page 254
Preliminary
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 22-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
OSC
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O Pins
Note: Refer to Figure 22-1 for load conditions.
FIGURE 22-5: BROWN-OUT RESET TIMING
BVDD
VDD
35
TABLE 22-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER,
AND BROWN-OUT RESET REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max Units
Conditions
30
TmcL MCLR Pulse Width (low)
2
7
—
—
µs VDD = 5V, -40˚C to +125˚C
31*
Twdt
Watchdog Timer Time-out Period
18
33
ms
VDD = 5V, -40˚C to +125˚C
(No Prescaler)
32
33*
34
Tost
Oscillation Start-up Timer Period
—
28
—
1024 TOSC
—
—
ms
µs
TOSC = OSC1 period
Tpwrt Power-up Timer Period
72
—
132
2.1
VDD = 5V, -40˚C to +125˚C
TIOZ
I/O Hi-impedance from MCLR Low
or WDT reset
35
TBOR
Brown-out Reset Pulse Width
100
—
—
VDD ≤ BVDD (D005)
µs
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
Preliminary
DS30234D-page 255
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 22-6: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
RA4/T0CKI
41
40
42
RC0/T1OSO/T1CKI
46
45
47
48
TMR0 or
TMR1
Note: Refer to Figure 22-1 for load conditions.
TABLE 22-5: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Param
No.
Sym
Characteristic
Min
Typ† Max Units Conditions
40*
Tt0H
T0CKI High Pulse Width
No Prescaler
0.5TCY + 20
—
—
ns Must also meet
parameter 42
With Prescaler
No Prescaler
10
0.5TCY + 20
10
—
—
—
—
—
—
—
—
—
—
ns
41*
42*
Tt0L
Tt0P
T0CKI Low Pulse Width
T0CKI Period
ns Must also meet
parameter 42
With Prescaler
No Prescaler
With Prescaler
ns
ns
TCY + 40
Greater of:
20 or TCY + 40
ns N = prescale value
(2, 4, ..., 256)
N
0.5TCY + 20
15
45*
46*
47*
Tt1H
Tt1L
Tt1P
T1CKI High Time Synchronous, Prescaler = 1
—
—
—
—
—
—
ns Must also meet
parameter 47
Synchronous, PIC16C6X
ns
ns
Prescaler =
2,4,8
PIC16LC6X
25
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
—
—
—
—
ns
ns
50
T1CKI Low Time
Synchronous, Prescaler = 1
Synchronous, PIC16C6X
0.5TCY + 20
ns Must also meet
parameter 47
15
25
ns
ns
Prescaler =
2,4,8
PIC16LC6X
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
ns
ns
50
T1CKI input period Synchronous PIC16C6X
Greater of:
30 OR TCY + 40
ns N = prescale value
(1, 2, 4, 8)
N
Greater of:
50 OR TCY + 40
N = prescale value
(1, 2, 4, 8)
PIC16LC6X
N
60
Asynchronous PIC16C6X
PIC16LC6X
—
—
—
—
—
ns
ns
100
DC
Ft1
Timer1 oscillator input frequency range
(oscillator enabled by setting bit T1OSCEN)
200
kHz
48
*
TCKEZtmr1 Delay from external clock edge to timer increment
2Tosc
—
7Tosc
—
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 256
Preliminary
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 22-7: CAPTURE/COMPARE/PWM TIMINGS (CCP1 AND CCP2)
RC1/T1OSI/CCP2
and RC2/CCP1
(Capture Mode)
50
51
52
54
RC1/T1OSI/CCP2
and RC2/CCP1
(Compare or
PWM Mode)
53
Note: Refer to Figure 22-1 for load conditions.
TABLE 22-6: CAPTURE/COMPARE/PWM REQUIREMENTS (CCP1 AND CCP2)
Param
No.
Sym Characteristic
Min
Typ† Max Units Conditions
50*
TccL CCP1 and CCP2 No Prescaler
input low time
0.5TCY + 20
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
With Prescaler PIC16CR63/R65
10
PIC16LCR63/R65
20
51*
TccH
No Prescaler
0.5TCY + 20
CCP1 and CCP2
input high time
With Prescaler PIC16CR63/R65
PIC16LCR63/R65
10
20
52*
53*
TccP
3TCY + 40
N
ns N = prescale value
(1,4, or 16)
CCP1 and CCP2 input period
TccR CCP1 and CCP2 output rise time
TccF CCP1 and CCP2 output fall time
PIC16CR63/R65
PIC16LCR63/R65
PIC16CR63/R65
PIC16LCR63/R65
—
—
—
—
10
25
10
25
25
45
25
45
ns
ns
ns
ns
54*
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
Preliminary
DS30234D-page 257
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 22-8: PARALLEL SLAVE PORT TIMING (PIC16CR65)
RE2/CS
RE0/RD
RE1/WR
65
RD7:RD0
62
64
63
Note: Refer to Figure 22-1 for load conditions
TABLE 22-7: PARALLEL SLAVE PORT REQUIREMENTS (PIC16CR65)
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units Conditions
62*
63*
TdtV2wrH Data in valid before WR↑ or CS↑ (setup time)
20
20
35
—
10
—
—
—
—
—
—
—
—
80
30
ns
ns
ns
ns
ns
TwrH2dtI WR↑ or CS↑ to data–in invalid (hold
PIC16CR65
PIC16LCR65
time)
64
TrdL2dtV RD↓ and CS↓ to data–out valid
TrdH2dtI RD↑ or CS↑ to data–out invalid
65*
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 258
Preliminary
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 22-9: SPI MODE TIMING
SS
70
SCK
(CKP = 0)
71
72
78
79
79
78
SCK
(CKP = 1)
80
SDO
SDI
77
75, 76
74
73
Note: Refer to Figure 22-1 for load conditions
TABLE 22-8: SPI MODE REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
70*
TssL2scH,
TssL2scL
SS↓ to SCK↓ or SCK↑ input
TCY
—
—
ns
71*
72*
73*
TscH
TscL
SCK input high time (slave mode)
SCK input low time (slave mode)
TCY + 20
TCY + 20
50
—
—
—
—
—
—
ns
ns
ns
TdiV2scH,
TdiV2scL
Setup time of SDI data input to SCK
edge
74*
TscH2diL,
TscL2diL
Hold time of SDI data input to SCK
edge
50
—
—
ns
75*
76*
77*
78*
79*
80*
TdoR
SDO data output rise time
—
—
10
—
—
—
10
10
—
10
10
—
25
25
50
25
25
50
ns
ns
ns
ns
ns
ns
TdoF
SDO data output fall time
TssH2doZ
TscR
SS↑ to SDO output hi-impedance
SCK output rise time (master mode)
SCK output fall time (master mode)
TscF
TscH2doV,
TscL2doV
SDO data output valid after SCK
edge
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
Preliminary
DS30234D-page 259
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 22-10: I C BUS START/STOP BITS TIMING
SCL
91
93
90
92
SDA
STOP
Condition
START
Condition
Note: Refer to Figure 22-1 for load conditions
2
TABLE 22-9: I C BUS START/STOP BITS REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min Typ Max Units
Conditions
90*
91*
92*
93
TSU:STA START condition
Setup time
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
4700
600
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Only relevant for repeated START
condition
ns
ns
ns
ns
THD:STA START condition
Hold time
4000
600
After this period the first clock
pulse is generated
TSU:STO STOP condition
Setup time
4700
600
THD:STO STOP condition
Hold time
4000
600
*
These parameters are characterized but not tested.
DS30234D-page 260
Preliminary
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 22-11: I C BUS DATA TIMING
103
102
100
101
SCL
90
106
107
91
92
SDA
In
110
109
109
SDA
Out
Note: Refer to Figure 22-1 for load conditions
2
TABLE 22-10: I C BUS DATA REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Max
Units
Conditions
100*
THIGH
Clock high time
100 kHz mode
400 kHz mode
4.0
0.6
—
—
µs
µs
Device must operate at a min-
imum of 1.5 MHz
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
4.7
—
—
101*
TLOW
Clock low time
100 kHz mode
µs
µs
Device must operate at a min-
imum of 1.5 MHz
400 kHz mode
1.3
—
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
—
—
102*
103*
TR
TF
SDA and SCL rise
time
100 kHz mode
400 kHz mode
1000
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10-400 pF
SDA and SCL fall time 100 kHz mode
400 kHz mode
—
300
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10-400 pF
90*
91*
TSU:STA START condition
setup time
100 kHz mode
400 kHz mode
4.7
0.6
4.0
0.6
0
—
—
µs
µs
µs
µs
ns
µs
ns
ns
µs
µs
ns
ns
µs
µs
Only relevant for repeated
START condition
THD:STA START condition hold 100 kHz mode
—
After this period the first clock
pulse is generated
time
400 kHz mode
100 kHz mode
400 kHz mode
—
106*
107*
92*
THD:DAT Data input hold time
—
0
0.9
—
TSU:DAT Data input setup time 100 kHz mode
400 kHz mode
250
100
4.7
0.6
—
Note 2
—
TSU:STO STOP condition setup 100 kHz mode
—
time
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
—
109*
110*
TAA
Output valid from
clock
3500
—
Note 1
—
TBUF
Bus free time
4.7
1.3
—
Time the bus must be free
before a new transmission can
start
—
Cb
Bus capacitive loading
—
400
pF
*
These parameters are characterized but not tested.
Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of
the falling edge of SCL to avoid unintended generation of START or STOP conditions.
2
2
2: A fast-mode (400 kHz) I C-bus device can be used in a standard-mode (100 kHz) I C-bus system, but the requirement
Tsu:DAT ≥ 250 ns must then be met.This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line
2
TR max.+tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I C bus specification) before the SCL line is
released.
1997 Microchip Technology Inc.
Preliminary
DS30234D-page 261
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 22-12: USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
RC6/TX/CK
pin
121
121
RC7/RX/DT
pin
120
122
Note: Refer to Figure 22-1 for load conditions
TABLE 22-11: USART SYNCHRONOUS TRANSMISSION REQUIREMENTS
Param Sym
No.
Characteristic
Min
Typ†
Max
Units Conditions
PIC16CR63/R65
PIC16LCR63/R65
PIC16CR63/R65
PIC16LCR63/R65
PIC16CR63/R65
PIC16LCR63/R65
—
—
—
—
—
—
—
—
—
—
—
—
80
100
45
ns
ns
ns
ns
ns
ns
120*
TckH2dtV
SYNC XMIT (MASTER & SLAVE)
Clock high to data out valid
121*
Tckrf
Tdtrf
Clock out rise time and fall time
(Master Mode)
50
122*
Data out rise time and fall time
45
50
*
These parameters are characterized but not tested.
†:
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
FIGURE 22-13: USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
RC6/TX/CK
125
pin
RC7/RX/DT
pin
126
Note: Refer to Figure 22-1 for load conditions
TABLE 22-12: USART SYNCHRONOUS RECEIVE REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units Conditions
125*
TdtV2ckL
TckL2dtl
SYNC RCV (MASTER & SLAVE)
Data setup before CK ↓ (DT setup time)
15
15
—
—
—
—
ns
ns
126*
Data hold after CK ↓ (DT hold time)
*
These parameters are characterized but not tested.
†:
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 262
Preliminary
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
23.0 ELECTRICAL CHARACTERISTICS FOR PIC16C66/67
(†)
Absolute Maximum Ratings
Ambient temperature under bias..............................................................................................................-55˚C to +125˚C
Storage temperature............................................................................................................................... -65˚C to +150˚C
Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4) ..........................................-0.3V to (VDD + 0.3V)
Voltage on VDD with respect to VSS .......................................................................................................... -0.3V to +7.5V
Voltage on MCLR with respect to VSS (Note 2) ...............................................................................................0V to +14V
Voltage on RA4 with respect to Vss.................................................................................................................0V to +14V
Total power dissipation (Note 1).................................................................................................................................1.0W
Maximum current out of VSS pin ............................................................................................................................300 mA
Maximum current into VDD pin...............................................................................................................................250 mA
Input clamp current, IIK (VI < 0 or VI > VDD) ......................................................................................................................±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD)...............................................................................................................±20 mA
Maximum output current sunk by any I/O pin...........................................................................................................25 mA
Maximum output current sourced by any I/O pin .....................................................................................................25 mA
Maximum current sunk by PORTA, PORTB, and PORTE (Note 3) (combined).....................................................200 mA
Maximum current sourced by PORTA, PORTB, and PORTE (Note 3) (combined) ...............................................200 mA
Maximum current sunk by PORTC and PORTD(Note 3) (combined) ...................................................................200 mA
Maximum current sourced by PORTC and PORTD(Note 3) (combined) ..............................................................200 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOl x IOL)
Note 2: Voltage spikes below VSS at the MCLR/VPP pin, inducing currents greater than 80 mA, may cause latch-up.
Thus, a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR/VPP pin rather
than pulling this pin directly to VSS.
Note 3: PORTD and PORTE not available on the PIC16C66.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 23-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16C66-04
PIC16C67-04
PIC16C66-10
PIC16C67-10
PIC16C66-20
PIC16C67-20
PIC16LC66-04
PIC16LC67-04
OSC
JW Devices
RC
VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 2.5V to 6.0V
VDD: 4.0V to 6.0V
IDD: 5 mA max. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 3.8 mA max. at 3V IDD: 5 mA max. at 5.5V
IPD: 16 µA max. at 4V IPD: 1.5 µA typ. at 4V
IPD: 1.5 µA typ. at 4V
IPD: 5 µA max. at 3V
IPD: 16 µA max. at 4V
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
Freq: 4 MHz max.
XT
HS
VDD: 4.0V to 6.0V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 2.5V to 6.0V
VDD: 4.0V to 6.0V
IDD: 5 mA max. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 2.7 mA typ. at 5.5V IDD: 3.8 mA max. at 3V IDD: 5 mA max. at 5.5V
IPD: 16 µA max. at 4V IPD: 1.5 µA typ. at 4V
Freq: 4 MHz max.
IPD: 1.5 µA typ. at 4V
Freq: 4 MHz max.
IPD: 5 µA max. at 3V
Freq: 4 MHz max.
IPD: 16 µA max. at 4V
Freq: 4 MHz max.
Freq: 4 MHz max.
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 13.5 mA typ. at
5.5V
IDD: 10 mA max. at 5.5V IDD: 20 mA max. at 5.5V
IDD: 20 mA max. at
5.5V
Not recommended for
use in HS mode
IPD: 1.5 µA typ. at 4.5V IPD 1.5 µA typ. at 4.5V IPD: 1.5 µA typ. at 4.5V
IPD: 1.5 µA typ. at 4.5V
Freq: 20 MHz max.
VDD: 2.5V to 6.0V
Freq: 4 MHz max.
Freq: 10 MHz max.
Freq: 20 MHz max.
LP
VDD: 4.0V to 6.0V
IDD: 52.5 µA typ.
at 32 kHz, 4.0V
IPD: 0.9 µA typ. at 4.0V
Freq: 200 kHz max.
VDD: 2.5V to 6.0V
IDD: 48 µA max. at 32 IDD: 48 µA max.
at 32 kHz, 3.0V
IPD: 5 µA max. at 3.0V IPD: 5 µA max. at 3.0V
Not recommended for
use in LP mode
Not recommended for
use in LP mode
kHz, 3.0V
Freq: 200 kHz max.
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifications. It is recom-
mended that the user select the device type that ensures the specifications required.
1997 Microchip Technology Inc.
DS30234D-page 263
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
23.1
DC Characteristics:
PIC16C66/67-04 (Commercial, Industrial, Extended)
PIC16C66/67-10 (Commercial, Industrial, Extended)
PIC16C66/67-20 (Commercial, Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40˚C ≤ TA ≤ +125˚C for extended,
DC CHARACTERISTICS
-40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym
VDD
Min Typ† Max Units
Conditions
D001 Supply Voltage
D001A
4.0
4.5
-
-
6.0
5.5
V
V
XT, RC and LP osc configuration
HS osc configuration
D002* RAM Data Retention
Voltage (Note 1)
VDR
-
1.5
-
V
D003 VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
-
VSS
-
V
See section on Power-on Reset for details
D004* VDD rise rate to ensure
internal Power-on Reset
signal
SVDD
BVDD
0.05
-
-
V/ms See section on Power-on Reset for details
D005 Brown-out Reset Voltage
3.7
3.7
-
4.0 4.3
4.0 4.4
V
V
BODEN configuration bit is enabled
Extended Range Only
D010 Supply Current (Note 2, 5) IDD
D013
2.7
5
mA XT, RC, osc config FOSC = 4 MHz, VDD = 5.5V
(Note 4)
-
-
10
20
mA HS osc config
FOSC = 20 MHz, VDD = 5.5V
D015* Brown-out Reset Current ∆IBOR
350 425 µA BOR enabled, VDD = 5.0V
(Note 6)
D020 Power-down Current
D021 (Note 3, 5)
D021A
IPD
-
-
-
-
10.5 42 µA VDD = 4.0V, WDT enabled,-40°C to +85°C
1.5
1.5
2.5
16
19
19
µA VDD = 4.0V, WDT disabled,-0°C to +70°C
µA VDD = 4.0V, WDT disabled,-40°C to +85°C
µA VDD = 4.0V, WDT disabled,-40°C to +125°C
D021B
D023* Brown-out Reset Current ∆IBOR
-
350 425 µA BOR enabled, VDD = 5.0V
(Note 6)
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,
MCLR = VDD; WDT enabled/disabled as specified.
3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from character-
ization and is for design guidance only. This is not tested.
6: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be
added to the base IDD or IPD measurement.
DS30234D-page 264
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
23.2
DC Characteristics: PIC16LC66/67-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature -40˚C
0˚C
≤ TA ≤ +85˚C for industrial and
≤ TA ≤ +70˚C for commercial
Param
No.
Characteristic
Sym Min Typ† Max Units
Conditions
D001
Supply Voltage
VDD
VDR
2.5
-
-
6.0
-
V
V
LP, XT, RC osc configuration (DC - 4 MHz)
D002*
RAM Data Retention
Voltage (Note 1)
1.5
D003
VDD start voltage to
ensure internal Power-on
Reset signal
VPOR
SVDD
BVDD
-
VSS
-
-
-
V
See section on Power-on Reset for details
D004*
VDD rise rate to ensure
internal Power-on Reset
signal
0.05
V/ms See section on Power-on Reset for details
D005
D010
Brown-out Reset Voltage
3.7
-
4.0
2.0
4.3
3.8
V
BODEN configuration bit is enabled
Supply Current (Note 2, 5) IDD
mA XT, RC osc configuration
FOSC = 4 MHz, VDD = 3.0V (Note 4)
D010A
D015*
-
-
22.5 48
350 425
µA LP osc configuration
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
Brown-out Reset Current ∆IBOR
µA BOR enabled, VDD = 5.0V
(Note 6)
D020
D021
D021A
Power-down Current
(Note 3, 5)
IPD
-
-
-
7.5
0.9
0.9
30
5
5
µA VDD = 3.0V, WDT enabled, -40°C to +85°C
µA VDD = 3.0V, WDT disabled, 0°C to +70°C
µA VDD = 3.0V, WDT disabled, -40°C to +85°C
D023*
Brown-out Reset Current ∆IBOR
-
350 425
µA BOR enabled, VDD = 5.0V
(Note 6)
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD,
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from character-
ization and is for design guidance only. This is not tested.
6: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be
added to the base IDD or IPD measurement.
1997 Microchip Technology Inc.
DS30234D-page 265
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
23.3
DC Characteristics:
PIC16C66/67-04 (Commercial, Industrial, Extended)
PIC16C66/67-10 (Commercial, Industrial, Extended)
PIC16C66/67-20 (Commercial, Industrial, Extended)
PIC16LC66/67-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +125˚C for extended,
-40˚C ≤ TA ≤ +85˚C for industrial and
DC CHARACTERISTICS
0˚C
≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in DC spec Section 23.1 and
Section 23.2
Param
No.
Characteristic
Sym
Min Typ Max
†
Units
Conditions
Input Low Voltage
I/O ports
VIL
D030
D030A
D031
D032
D033
with TTL buffer
VSS
VSS
VSS
Vss
Vss
-
-
-
-
-
0.15VDD
0.8V
0.2VDD
0.2VDD
0.3VDD
V
V
V
V
V
For entire VDD range
4.5V ≤ VDD ≤ 5.5V
with Schmitt Trigger buffer
MCLR, OSC1 (in RC mode)
OSC1 (in XT, HS and LP)
Input High Voltage
I/O ports
Note1
VIH
-
-
-
D040
D040A
with TTL buffer
2.0
0.25VDD
+ 0.8V
VDD
VDD
V
V
4.5V ≤ VDD ≤ 5.5V
For entire VDD range
D041
D042
with Schmitt Trigger buffer
MCLR
0.8VDD
0.8VDD
0.7VDD
0.9VDD
50
-
-
-
-
VDD
VDD
VDD
VDD
400
V
V
V
V
For entire VDD range
Note1
D042A OSC1 (XT, HS and LP)
D043
D070
OSC1 (in RC mode)
PORTB weak pull-up current
Input Leakage Current (Notes 2, 3)
I/O ports
IPURB
IIL
250
µA VDD = 5V, VPIN = VSS
D060
-
-
±1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
D061
D063
MCLR, RA4/T0CKI
OSC1
-
-
-
-
±5
±5
µA Vss ≤ VPIN ≤ VDD
µA Vss ≤ VPIN ≤ VDD, XT, HS and
LP osc configuration
Output Low Voltage
D080
I/O ports
VOL
-
-
-
-
-
-
-
-
0.6
0.6
0.6
0.6
V
V
V
V
IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 7.0 mA, VDD = 4.5V,
-40°C to +125°C
IOL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 1.2 mA, VDD = 4.5V,
-40°C to +125°C
D080A
D083
OSC2/CLKOUT (RC osc config)
D083A
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
DS30234D-page 266
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +125˚C for extended,
-40˚C ≤ TA ≤ +85˚C for industrial and
DC CHARACTERISTICS
0˚C
≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in DC spec Section 23.1 and
Section 23.2
Param
No.
Characteristic
Sym
Min Typ Max
†
Units
Conditions
Output High Voltage
D090
I/O ports (Note 3)
VOH
VDD-0.7
VDD-0.7
VDD-0.7
VDD-0.7
-
-
-
-
-
-
-
-
V
V
V
V
V
IOH = -3.0 mA, VDD = 4.5V,
-40°C to +85°C
IOH = -2.5 mA, VDD = 4.5V,
-40°C to +125°C
IOH = -1.3 mA, VDD = 4.5V,
-40°C to +85°C
IOH = -1.0 mA, VDD = 4.5V,
-40°C to +125°C
D090A
D092
OSC2/CLKOUT (RC osc config)
-
D092A
-
D150* Open-Drain High Voltage
Capacitive Loading Specs on Out-
VOD
14
RA4 pin
put Pins
D100
OSC2 pin
COSC2
-
-
15
pF In XT, HS and LP modes when
external clock is used to drive
OSC1.
D101
D102
All I/O pins and OSC2 (in RC mode) CIO
-
-
-
-
50
400
pF
pF
2
Cb
SCL, SDA in I C mode
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C6X be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
1997 Microchip Technology Inc.
DS30234D-page 267
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
23.4
Timing Parameter Symbology
The timing parameter symbols have been created following one of the following formats:
2
1. TppS2ppS
2. TppS
3. TCC:ST
4. Ts
(I C specifications only)
2
(I C specifications only)
T
F
Frequency
T
Time
Lowercase letters (pp) and their meanings:
pp
cc
CCP1
CLKOUT
CS
osc
rd
OSC1
RD
ck
cs
di
rw
sc
ss
t0
RD or WR
SCK
SDI
do
dt
SDO
SS
Data in
I/O port
MCLR
T0CKI
T1CKI
WR
io
t1
mc
wr
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
2
I C only
AA
output access
Bus free
High
Low
High
Low
BUF
2
TCC:ST (I C specifications only)
CC
HD
ST
DAT
STA
Hold
SU
Setup
DATA input hold
START condition
STO
STOP condition
FIGURE 23-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load condition 1
Load condition 2
VDD/2
CL
RL
Pin
VSS
CL
Pin
RL = 464Ω
CL = 50 pF for all pins except OSC2/CLKOUT
but including D and E outputs as ports
VSS
Note 1: PORTD and PORTE are not imple-
mented on the PIC16C66.
15 pF for OSC2 output
DS30234D-page 268
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
23.5
Timing Diagrams and Specifications
FIGURE 23-2: EXTERNAL CLOCK TIMING
Q1
1
Q2
Q3
Q4
4
Q4
Q1
OSC1
3
3
4
2
CLKOUT
TABLE 23-2: EXTERNAL CLOCK TIMING REQUIREMENTS
Param
No.
Sym Characteristic
Min
Typ†
Max
Units Conditions
Fosc External CLKIN Frequency
DC
DC
DC
DC
DC
DC
0.1
4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TCY
—
—
—
—
—
—
4
4
MHz XT and RC osc mode
MHz HS osc mode (-04)
MHz HS osc mode (-10)
MHz HS osc mode (-20)
kHz LP osc mode
(Note 1)
10
20
200
4
Oscillator Frequency
(Note 1)
MHz RC osc mode
4
MHz XT osc mode
20
200
—
MHz HS osc mode
5
kHz LP osc mode
1
Tosc External CLKIN Period
250
250
100
50
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
ns
ns
µs
ns
ns
ns
ns
XT and RC osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
(Note 1)
—
—
—
5
—
Oscillator Period
(Note 1)
250
250
250
100
50
—
RC osc mode
10,000
250
250
250
—
XT osc mode
HS osc mode (-04)
HS osc mode (-10)
HS osc mode (-20)
LP osc mode
5
2
TCY
Instruction Cycle Time (Note 1)
200
100
2.5
15
DC
—
TCY = 4/FOSC
3*
TosL, External Clock in (OSC1) High or
TosH Low Time
XT oscillator
—
LP oscillator
—
HS oscillator
4*
TosR, External Clock in (OSC1) Rise or
TosF Fall Time
—
25
50
15
XT oscillator
—
LP oscillator
—
HS oscillator
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin.
When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices.
1997 Microchip Technology Inc.
DS30234D-page 269
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 23-3: CLKOUT AND I/O TIMING
Q1
Q2
Q3
Q4
OSC1
11
10
CLKOUT
13
12
19
18
14
16
I/O Pin
(input)
15
17
I/O Pin
(output)
new value
old value
20, 21
Note: Refer to Figure 23-1 for load conditions.
TABLE 23-3: CLKOUT AND I/O TIMING REQUIREMENTS
Parameter Sym
No.
Characteristic
Min
Typ†
Max
Units Conditions
10*
11*
12*
13*
14*
15*
16*
17*
18*
TosH2ckL OSC1↑ to CLKOUT↓
TosH2ckH OSC1↑ to CLKOUT↑
—
75
75
35
35
—
—
—
50
—
—
—
10
—
10
—
—
—
200
200
100
100
ns
ns
ns
ns
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
Note 1
—
TckR
TckF
CLKOUT rise time
CLKOUT fall time
—
—
TckL2ioV CLKOUT ↓ to Port out valid
TioV2ckH Port in valid before CLKOUT ↑
—
0.5TCY + 20 ns
Tosc + 200
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
TckH2ioI
TosH2ioV OSC1↑ (Q1 cycle) to Port out valid
TosH2ioI OSC1↑ (Q2 cycle) to Port input PIC16C66/67
invalid (I/O in hold time)
TioV2osH Port input valid to OSC1↑ (I/O in setup time)
Port in hold after CLKOUT ↑
0
—
150
—
100
200
0
PIC16LC66/67
—
19*
20*
—
TioR
Port output rise time
Port output fall time
INT pin high or low time
PIC16C66/67
PIC16LC66/67
PIC16C66/67
PIC16LC66/67
—
40
80
40
80
—
—
21*
TioF
—
—
22††*
23††*
Tinp
Trbp
TCY
TCY
RB7:RB4 change INT high or low time
—
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
†† These parameters are asynchronous events not related to any internal clock edge.
Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
DS30234D-page 270
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 23-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP
TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
OSC
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O Pins
Note: Refer to Figure 23-1 for load conditions.
FIGURE 23-5: BROWN-OUT RESET TIMING
BVDD
VDD
35
TABLE 23-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER,
AND BROWN-OUT RESET REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max Units
Conditions
30
TmcL MCLR Pulse Width (low)
2
7
—
—
µs VDD = 5V, -40˚C to +125˚C
31*
Twdt
Watchdog Timer Time-out Period
18
33
ms
VDD = 5V, -40˚C to +125˚C
(No Prescaler)
32
33*
34
Tost
Oscillation Start-up Timer Period
—
28
—
1024 TOSC
—
—
ms
µs
TOSC = OSC1 period
Tpwrt Power-up Timer Period
72
—
132
2.1
VDD = 5V, -40˚C to +125˚C
TIOZ
I/O Hi-impedance from MCLR Low
or WDT reset
35
TBOR
Brown-out Reset Pulse Width
100
—
—
VDD ≤ BVDD (D005)
µs
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 271
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 23-6: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
RA4/T0CKI
41
40
42
RC0/T1OSO/T1CKI
46
45
47
48
TMR0 or
TMR1
Note: Refer to Figure 23-1 for load conditions.
TABLE 23-5: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Param
No.
Sym
Characteristic
Min
Typ† Max Units Conditions
40*
Tt0H
T0CKI High Pulse Width
No Prescaler
0.5TCY + 20
—
—
ns Must also meet
parameter 42
With Prescaler
No Prescaler
10
0.5TCY + 20
10
—
—
—
—
—
—
—
—
—
—
ns
41*
42*
Tt0L
Tt0P
T0CKI Low Pulse Width
T0CKI Period
ns Must also meet
parameter 42
With Prescaler
No Prescaler
With Prescaler
ns
ns
TCY + 40
Greater of:
20 or TCY + 40
ns N = prescale value
(2, 4, ..., 256)
N
0.5TCY + 20
15
45*
46*
47*
Tt1H
Tt1L
Tt1P
T1CKI High Time Synchronous, Prescaler = 1
—
—
—
—
—
—
ns Must also meet
parameter 47
Synchronous, PIC16C6X
ns
ns
Prescaler =
2,4,8
PIC16LC6X
25
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
—
—
—
—
ns
ns
50
T1CKI Low Time
Synchronous, Prescaler = 1
Synchronous, PIC16C6X
0.5TCY + 20
ns Must also meet
parameter 47
15
25
ns
ns
Prescaler =
2,4,8
PIC16LC6X
Asynchronous PIC16C6X
PIC16LC6X
30
—
—
—
—
—
—
ns
ns
50
T1CKI input period Synchronous PIC16C6X
Greater of:
30 OR TCY + 40
ns N = prescale value
(1, 2, 4, 8)
N
Greater of:
50 OR TCY + 40
N = prescale value
(1, 2, 4, 8)
PIC16LC6X
N
60
Asynchronous PIC16C6X
PIC16LC6X
—
—
—
—
—
ns
ns
100
DC
Ft1
Timer1 oscillator input frequency range
(oscillator enabled by setting bit T1OSCEN)
200
kHz
48
*
TCKEZtmr1 Delay from external clock edge to timer increment
2Tosc
—
7Tosc
—
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 272
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 23-7: CAPTURE/COMPARE/PWM TIMINGS (CCP1 AND CCP2)
RC1/T1OSI/CCP2
and RC2/CCP1
(Capture Mode)
50
51
52
54
RC1/T1OSI/CCP2
and RC2/CCP1
(Compare or
PWM Mode)
53
Note: Refer to Figure 23-1 for load conditions.
TABLE 23-6: CAPTURE/COMPARE/PWM REQUIREMENTS (CCP1 AND CCP2)
Parameter Sym Characteristic
No.
Min
Typ† Max Units Conditions
50*
TccL CCP1 and CCP2 No Prescaler
input low time
0.5TCY + 20
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
With Prescaler PIC16C66/67
10
PIC16LC66/67
20
51*
TccH
No Prescaler
0.5TCY + 20
CCP1 and CCP2
input high time
With Prescaler PIC16C66/67
PIC16LC66/67
10
20
52*
53*
TccP
3TCY + 40
N
ns N = prescale value
(1,4, or 16)
CCP1 and CCP2 input period
TccR CCP1 and CCP2 output rise time
TccF CCP1 and CCP2 output fall time
PIC16C66/67
PIC16LC66/67
PIC16C66/67
PIC16LC66/67
—
—
—
—
10
25
10
25
25
45
25
45
ns
ns
ns
ns
54*
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 273
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 23-8: PARALLEL SLAVE PORT TIMING (PIC16C67)
RE2/CS
RE0/RD
RE1/WR
65
RD7:RD0
62
64
63
Note: Refer to Figure 23-1 for load conditions
TABLE 23-7: PARALLEL SLAVE PORT REQUIREMENTS (PIC16C67)
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units Conditions
62*
TdtV2wrH Data in valid before WR↑ or CS↑ (setup time)
20
25
—
—
—
—
ns
ns
Extended
Range Only
63*
64
TwrH2dtI WR↑ or CS↑ to data–in invalid (hold
PIC16C67
PIC16LC67
20
35
—
—
—
—
—
—
—
—
80
90
ns
ns
ns
ns
time)
TrdL2dtV RD↓ and CS↓ to data–out valid
Extended
Range Only
65*
TrdH2dtI RD↑ or CS↑ to data–out invalid
10
—
30
ns
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 274
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 23-9: SPI MASTER MODE TIMING (CKE = 0)
SS
70
SCK
(CKP = 0)
71
72
78
79
79
SCK
(CKP = 1)
78
80
BIT6 - - - - - -1
MSB
LSB
SDO
SDI
75, 76
MSB IN
74
BIT6 - - - -1
LSB IN
73
Refer to Figure 23-1 for load conditions.
FIGURE 23-10: SPI MASTER MODE TIMING (CKE = 1)
SS
81
SCK
(CKP = 0)
71
72
79
78
73
SCK
(CKP = 1)
80
LSB
MSB
BIT6 - - - - - -1
BIT6 - - - -1
SDO
SDI
75, 76
MSB IN
74
LSB IN
Refer to Figure 23-1 for load conditions.
1997 Microchip Technology Inc.
DS30234D-page 275
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 23-11: SPI SLAVE MODE TIMING (CKE = 0)
SS
70
SCK
(CKP = 0)
83
71
72
78
79
79
SCK
(CKP = 1)
78
80
MSB
LSB
SDO
SDI
BIT6 - - - - - -1
77
75, 76
MSB IN
74
BIT6 - - - -1
LSB IN
73
Refer to Figure 23-1 for load conditions.
FIGURE 23-12: SPI SLAVE MODE TIMING (CKE = 1)
82
SS
70
SCK
83
(CKP = 0)
71
72
SCK
(CKP = 1)
80
MSB
BIT6 - - - - - -1
BIT6 - - - -1
LSB
SDO
SDI
75, 76
77
MSB IN
74
LSB IN
Refer to Figure 23-1 for load conditions.
DS30234D-page 276
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
TABLE 23-8: SPI MODE REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
70*
TssL2scH,
TssL2scL
SS↓ to SCK↓ or SCK↑ input
TCY
—
—
ns
71*
72*
73*
TscH
TscL
SCK input high time (slave mode)
SCK input low time (slave mode)
TCY + 20
TCY + 20
100
—
—
—
—
—
—
ns
ns
ns
TdiV2scH,
TdiV2scL
Setup time of SDI data input to SCK
edge
74*
TscH2diL,
TscL2diL
Hold time of SDI data input to SCK
edge
100
—
—
ns
75*
76*
77*
78*
79*
80*
TdoR
SDO data output rise time
—
—
10
—
—
—
10
10
—
10
10
—
25
25
50
25
25
50
ns
ns
ns
ns
ns
ns
TdoF
SDO data output fall time
TssH2doZ
TscR
SS↑ to SDO output hi-impedance
SCK output rise time (master mode)
SCK output fall time (master mode)
TscF
TscH2doV,
TscL2doV
SDO data output valid after SCK
edge
81*
82*
83*
TdoV2scH,
TdoV2scL
SDO data output setup to SCK
edge
TCY
—
—
—
—
—
50
—
ns
ns
ns
TssL2doV
SDO data output valid after SS↓
edge
TscH2ssH,
TscL2ssH
SS ↑ after SCK edge
1.5TCY + 40
*
These parameters are characterized but not tested.
†
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
1997 Microchip Technology Inc.
DS30234D-page 277
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 23-13: I C BUS START/STOP BITS TIMING
SCL
91
93
90
92
SDA
STOP
Condition
START
Condition
Note: Refer to Figure 23-1 for load conditions
2
TABLE 23-9: I C BUS START/STOP BITS REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min Typ Max Units
Conditions
90*
91*
92*
93
TSU:STA START condition
Setup time
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
4700
600
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Only relevant for repeated START
condition
ns
ns
ns
ns
THD:STA START condition
Hold time
4000
600
After this period the first clock
pulse is generated
TSU:STO STOP condition
Setup time
4700
600
THD:STO STOP condition
Hold time
4000
600
*
These parameters are characterized but not tested.
DS30234D-page 278
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
2
FIGURE 23-14: I C BUS DATA TIMING
103
102
100
101
SCL
90
106
107
91
92
SDA
In
110
109
109
SDA
Out
Note: Refer to Figure 23-1 for load conditions
2
TABLE 23-10: I C BUS DATA REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Max
Units
Conditions
100*
THIGH
Clock high time
100 kHz mode
400 kHz mode
4.0
0.6
—
—
µs
µs
Device must operate at a min-
imum of 1.5 MHz
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
4.7
—
—
101*
TLOW
Clock low time
100 kHz mode
µs
µs
Device must operate at a min-
imum of 1.5 MHz
400 kHz mode
1.3
—
Device must operate at a min-
imum of 10 MHz
SSP Module
1.5TCY
—
—
102*
103*
TR
TF
SDA and SCL rise
time
100 kHz mode
400 kHz mode
1000
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10-400 pF
SDA and SCL fall time 100 kHz mode
400 kHz mode
—
300
300
ns
ns
20 + 0.1Cb
Cb is specified to be from
10-400 pF
90*
91*
TSU:STA START condition
setup time
100 kHz mode
400 kHz mode
4.7
0.6
4.0
0.6
0
—
—
µs
µs
µs
µs
ns
µs
ns
ns
µs
µs
ns
ns
µs
µs
Only relevant for repeated
START condition
THD:STA START condition hold 100 kHz mode
—
After this period the first clock
pulse is generated
time
400 kHz mode
100 kHz mode
400 kHz mode
—
106*
107*
92*
THD:DAT Data input hold time
—
0
0.9
—
TSU:DAT Data input setup time 100 kHz mode
400 kHz mode
250
100
4.7
0.6
—
Note 2
—
TSU:STO STOP condition setup 100 kHz mode
—
time
400 kHz mode
100 kHz mode
400 kHz mode
100 kHz mode
400 kHz mode
—
109*
110*
TAA
Output valid from
clock
3500
—
Note 1
—
TBUF
Bus free time
4.7
1.3
—
Time the bus must be free
before a new transmission can
start
—
Cb
Bus capacitive loading
—
400
pF
*
These parameters are characterized but not tested.
Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of
the falling edge of SCL to avoid unintended generation of START or STOP conditions.
2
2
2: A fast-mode (400 kHz) I C-bus device can be used in a standard-mode (100 kHz) I C-bus system, but the requirement
Tsu:DAT ≥ 250 ns must then be met.This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line
2
TR max.+tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I C bus specification) before the SCL line is
released.
1997 Microchip Technology Inc.
DS30234D-page 279
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 23-15: USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
RC6/TX/CK
pin
121
121
RC7/RX/DT
pin
120
122
Note: Refer to Figure 23-1 for load conditions
TABLE 23-11: USART SYNCHRONOUS TRANSMISSION REQUIREMENTS
Parameter Sym
No.
Characteristic
Min
Typ†
Max
Units Conditions
PIC16C66/67
PIC16LC66/67
PIC16C66/67
PIC16LC66/67
PIC16C66/67
PIC16LC66/67
—
—
—
—
—
—
—
—
—
—
—
—
80
100
45
ns
ns
ns
ns
ns
ns
120*
TckH2dtV
SYNC XMIT (MASTER & SLAVE)
Clock high to data out valid
121*
Tckrf
Tdtrf
Clock out rise time and fall time
(Master Mode)
50
122*
Data out rise time and fall time
45
50
*
These parameters are characterized but not tested.
†:
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
FIGURE 23-16: USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
RC6/TX/CK
125
pin
RC7/RX/DT
pin
126
Note: Refer to Figure 23-1 for load conditions
TABLE 23-12: USART SYNCHRONOUS RECEIVE REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max
Units Conditions
125*
TdtV2ckL
TckL2dtl
SYNC RCV (MASTER & SLAVE)
Data setup before CK ↓ (DT setup time)
15
15
—
—
—
—
ns
ns
126*
Data hold after CK ↓ (DT hold time)
*
These parameters are characterized but not tested.
†:
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
DS30234D-page 280
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
24.0 DC AND AC CHARACTERISTICS GRAPHS AND TABLES FOR:
PIC16C62, PIC16C62A, PIC16CR62, PIC16C63, PIC16C64, PIC16C64A,
PIC16CR64, PIC16C65A, PIC16C66, PIC16C67
The graphs and tables provided in this section are for design guidance and are not tested or guaranteed.
In some graphs or tables the data presented are outside specified operating range (i.e., outside specified VDD
range). This is for information only and devices are guaranteed to operate properly only within the specified
range.
Note: The data presented in this section is a statistical summary of data collected on units from different lots over
a period of time and matrix samples. 'Typical' represents the mean of the distribution at, 25°C, while 'max'
or 'min' represents (mean +3σ) and (mean -3σ) respectively where σ is standard deviation.
FIGURE 24-1: TYPICAL IPD vs. VDD (WDT DISABLED, RC MODE)
35
30
25
20
15
10
5
0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD(Volts)
FIGURE 24-2: MAXIMUM IPD vs. VDD (WDT DISABLED, RC MODE)
10.000
85°C
70°C
1.000
0.100
25°C
0°C
-40°C
0.010
0.001
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD(Volts)
1997 Microchip Technology Inc.
DS30234D-page 281
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 24-3: TYPICAL IPD vs. VDD @ 25°C
FIGURE 24-5: TYPICAL RC OSCILLATOR
(WDT ENABLED, RC MODE)
FREQUENCY vs. VDD
Cext = 22 pF,T = 25°C
6.0
5.5
5.0
25
20
15
10
5
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
R = 5k
R = 10k
R = 100k
5.5
0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD(Volts)
2.5
3.0
3.5
4.0
4.5
5.0
6.0
VDD(Volts)
Shaded area is beyond recommended range.
FIGURE 24-4: MAXIMUM IPD vs. VDD (WDT
ENABLED, RC MODE)
FIGURE 24-6: TYPICAL RC OSCILLATOR
FREQUENCY vs. VDD
35
-40°C
Cext = 100 pF,T = 25°C
30
0°C
2.4
2.2
25
20
R = 3.3k
2.0
1.8
1.6
70°C
15
R = 5k
1.4
85°C
1.2
10
1.0
R = 10k
5
0
0.8
0.6
0.4
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
R = 100k
0.2
VDD(Volts)
0.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD(Volts)
FIGURE 24-7: TYPICAL RC OSCILLATOR
FREQUENCY vs. VDD
Cext = 300 pF,T = 25°C
1000
900
800
R = 3.3k
700
600
R = 5k
500
400
R = 10k
300
200
R = 100k
5.5 6.0
100
0
2.5
3.0
3.5
4.0
4.5
5.0
VDD(Volts)
DS30234D-page 282
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 24-8: TYPICAL IPD vs. VDD BROWN-
FIGURE 24-10: TYPICAL IPD vs.TIMER1
ENABLED (32 kHz, RC0/RC1
= 33 pF/33 pF, RC MODE)
OUT DETECT ENABLED (RC
MODE)
1400
1200
1000
800
600
400
200
0
30
25
20
15
10
5
Device NOT in
Brown-out Reset
Device in
Brown-out
Reset
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD(Volts)
0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
The shaded region represents the built-in hysteresis of the
brown-out reset circuitry.
VDD(Volts)
FIGURE 24-9: MAXIMUM IPD vs. VDD
BROWN-OUT DETECT
ENABLED
FIGURE 24-11: MAXIMUM IPD vs.TIMER1
ENABLED
(32 kHz, RC0/RC1 = 33 pF/33
(85°C TO -40°C, RC MODE)
pF, 85°C TO -40°C, RC MODE)
1600
1400
1200
45
40
35
30
1000
Device NOT in
Brown-out Reset
800
600
400
200
0
Device in
Brown-out
Reset
25
20
15
10
5
4.3
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD(Volts)
0
The shaded region represents the built-in hysteresis of the
brown-out reset circuitry.
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD(Volts)
1997 Microchip Technology Inc.
DS30234D-page 283
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 24-12: TYPICAL IDD vs. FREQUENCY (RC MODE @ 22 pF, 25°C)
2000
1800
1600
1400
1200
1000
800
6.0V
5.5V
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
600
400
200
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
Frequency(MHz)
Shaded area is
beyond recommended range
FIGURE 24-13: MAXIMUM IDD vs. FREQUENCY (RC MODE @ 22 pF, -40°C TO 85°C)
2000
6.0V
1800
1600
1400
1200
1000
800
600
400
200
0
5.5V
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
Frequency(MHz)
Shaded area is
beyond recommended range
DS30234D-page 284
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 24-14: TYPICAL IDD vs. FREQUENCY (RC MODE @ 100 pF, 25°C)
1600
1400
1200
1000
800
6.0V
5.5V
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
600
400
200
0
0
200
Shaded area is
beyond recommended range
400
600
800
1000
1200
1400
1600
1800
Frequency(kHz)
FIGURE 24-15: MAXIMUM IDD vs. FREQUENCY (RC MODE @ 100 pF, -40°C TO 85°C)
1600
6.0V
5.5V
1400
1200
1000
800
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
600
400
200
0
0
200
Shaded area is
beyond recommended range
400
600
800
1000
1200
1400
1600
1800
Frequency(kHz)
1997 Microchip Technology Inc.
DS30234D-page 285
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 24-16: TYPICAL IDD vs. FREQUENCY (RC MODE @ 300 pF, 25°C)
1200
1000
800
600
400
200
0
6.0V
5.5V
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
0
100
200
300
400
500
600
700
Frequency(kHz)
FIGURE 24-17: MAXIMUM IDD vs. FREQUENCY (RC MODE @ 300 pF, -40°C TO 85°C)
1200
6.0V
5.5V
1000
800
600
400
200
0
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
0
100
200
300
400
500
600
700
Frequency(kHz)
DS30234D-page 286
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 24-18: TYPICAL IDD vs.
CAPACITANCE @ 500 kHz
(RC MODE)
FIGURE 24-19: TRANSCONDUCTANCE(gm)
OF HS OSCILLATOR vs. VDD
600
4.0
Max -40°C
5.0V
3.5
500
400
300
200
100
0
3.0
4.0V
3.0V
2.5
Typ 25°C
2.0
Min 85°C
1.5
1.0
0.5
0.0
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
20 pF
100 pF
300 pF
VDD(Volts)
Capacitance(pF)
Shaded area is
beyond recommended range
TABLE 24-1: RC OSCILLATOR
FREQUENCIES
FIGURE 24-20: TRANSCONDUCTANCE(gm)
OF LP OSCILLATOR vs. VDD
Average
110
Cext
Rext
100
Max -40°C
Fosc @ 5V, 25°C
90
80
70
22 pF
5k
10k
100k
3.3k
5k
4.12 MHz
2.35 MHz
268 kHz
1.80 MHz
1.27 MHz
688 kHz
77.2 kHz
707 kHz
501 kHz
269 kHz
28.3 kHz
± 1.4%
± 1.4%
60
50
40
30
20
10
0
Typ 25°C
± 1.1%
± 1.0%
± 1.0%
± 1.2%
± 1.0%
± 1.4%
± 1.2%
± 1.6%
± 1.1%
100 pF
300 pF
10k
100k
3.3k
5k
Min 85°C
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0
VDD(Volts)
Shaded areas are
beyond recommended range
10k
100k
FIGURE 24-21: TRANSCONDUCTANCE(gm)
OF XT OSCILLATOR vs. VDD
The percentage variation indicated here is part to
part variation due to normal process distribution.The
variation indicated is ±3 standard deviation from
average value for VDD = 5V.
1000
900
Max -40°C
800
700
600
500
400
300
200
100
0
Typ 25°C
Min 85°C
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0
VDD(Volts)
Shaded areas are
beyond recommended range
1997 Microchip Technology Inc.
DS30234D-page 287
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 24-22: TYPICAL XTAL STARTUP
FIGURE 24-24: TYPICAL XTAL STARTUP
TIME vs. VDD (LP MODE, 25°C)
TIME vs. VDD (XT MODE, 25°C)
3.5
3.0
2.5
70
60
50
40
2.0
200 kHz, 68 pF/68 pF
32 kHz, 33 pF/33 pF
1.5
30
20
200 kHz, 47 pF/47 pF
1 MHz, 15 pF/15 pF
4 MHz, 15 pF/15 pF
1.0
10
0
0.5
0.0
200 kHz, 15 pF/15 pF
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD(Volts)
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD(Volts)
FIGURE 24-23: TYPICAL XTAL STARTUP
TIME vs. VDD (HS MODE,
25°C)
TABLE 24-2: CAPACITOR SELECTION
FOR CRYSTAL
OSCILLATORS
Crystal
Freq
Cap. Range
C1
Cap. Range
C2
7
6
Osc Type
LP
32 kHz
200 kHz
200 kHz
1 MHz
33 pF
15 pF
33 pF
15 pF
20 MHz, 33 pF/33 pF
5
XT
HS
47-68 pF
15 pF
47-68 pF
15 pF
4
8 MHz, 33 pF/33 pF
4 MHz
15 pF
15 pF
3
20 MHz, 15 pF/15 pF
4 MHz
15 pF
15 pF
8 MHz, 15 pF/15 pF
2
8 MHz
15-33 pF
15-33 pF
15-33 pF
15-33 pF
20 MHz
1
4.0
4.5
5.0
5.5
6.0
VDD(Volts)
Crystals
Used
32 kHz
200 kHz
1 MHz
Epson C-001R32.768K-A
STD XTL 200.000KHz
ECS ECS-10-13-1
± 20 PPM
± 20 PPM
± 50 PPM
± 50 PPM
± 30 PPM
± 30 PPM
4 MHz
ECS ECS-40-20-1
8 MHz
EPSON CA-301 8.000M-C
EPSON CA-301 20.000M-C
20 MHz
DS30234D-page 288
1997 Microchip Technology Inc.
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 24-25: TYPICAL IDD vs. FREQUENCY
(LP MODE, 25°C)
FIGURE 24-27: TYPICAL IDD vs. FREQUENCY
(XT MODE, 25°C)
1800
1600
6.0V
120
100
80
60
40
20
0
5.5V
1400
5.0V
1200
4.5V
1000
800
600
4.0V
3.5V
6.0V
5.5V
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
3.0V
2.5V
400
200
0
50
100
150
200
Frequency(kHz)
0
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0
Frequency(MHz)
FIGURE 24-26: MAXIMUM IDD vs.
FREQUENCY
FIGURE 24-28: MAXIMUM IDD vs.
FREQUENCY
(LP MODE, 85°C TO -40°C)
(XT MODE, -40°C TO 85°C)
1800
1600
1400
1200
6.0V
5.5V
5.0V
4.5V
140
120
100
80
4.0V
1000
3.5V
6.0V
5.5V
5.0V
4.5V
4.0V
3.5V
60
800
600
3.0V
40
2.5V
20
400
200
3.0V
2.5V
0
0
50
100
150
200
0
Frequency(kHz)
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0
Frequency(MHz)
1997 Microchip Technology Inc.
DS30234D-page 289
PIC16C6X
Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67
FIGURE 24-29: TYPICAL IDD vs. FREQUENCY
FIGURE 24-30: MAXIMUM IDD vs.
(HS MODE, 25°C)
FREQUENCY
(HS MODE, -40°C TO 85°C)
7.0
6.0
5.0
4.0
3.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0.0
6.0V
2.0
5.5V
5.0V
4.5V
4.0V
6.0V
5.5V
5.0V
4.5V
4.0V
1.0
0.0
1
2
4
6
8
10
12
14
16
18
20
1
2
4
6
8
10
12
14
16
18
20
Frequency(MHz)
Frequency(MHz)
DS30234D-page 290
1997 Microchip Technology Inc.
PIC16C6X
25.0 PACKAGING INFORMATION
25.1
18-Lead Plastic Dual In-line (300 mil) (P)
N
α
C
E1
E
eA
eB
Pin No. 1
Indicator
Area
D
S
S1
e1
Base
Plane
Seating
Plane
L
B1
B
A
A2
A1
D1
Package Group: Plastic Dual In-Line (PLA)
Millimeters
Inches
Symbol
Min
Max
Notes
Min
Max
Notes
α
0°
10°
4.064
–
0°
10°
0.160
–
A
–
–
A1
A2
B
0.381
3.048
0.355
1.524
0.203
22.479
20.320
7.620
6.096
2.489
7.620
7.874
3.048
18
0.015
0.120
0.014
0.060
0.008
0.885
0.800
0.300
0.240
0.098
0.300
0.310
0.120
18
3.810
0.559
1.524
0.381
23.495
20.320
8.255
7.112
2.591
7.620
9.906
3.556
18
0.150
0.022
0.060
0.015
0.925
0.800
0.325
0.280
0.102
0.300
0.390
0.140
18
B1
C
Reference
Typical
Reference
Typical
D
D1
E
Reference
Reference
E1
e1
eA
eB
L
Typical
Typical
Reference
Reference
N
S
0.889
0.127
–
0.035
0.005
–
S1
–
–
1997 Microchip Technology Inc.
DS30234D-page 291
PIC16C6X
25.2
28-Lead Plastic Dual In-line (300 mil) (SP)
N
α
E1
E
C
eA
eB
Pin No. 1
Indicator
Area
B2
B1
D
S
Base
Plane
Seating
Plane
L
Detail A
B
Detail A
B3
A
A2
A1
e1
D1
Package Group: Plastic Dual In-Line (PLA)
Millimeters
Inches
Max
Symbol
Min
Max
Notes
Min
Notes
α
0°
10°
4.572
–
0°
10°
A
3.632
0.381
3.175
0.406
1.016
0.762
0.203
0.203
0.143
0.015
0.125
0.016
0.040
0.030
0.008
0.008
1.385
1.300
0.310
0.280
0.100
0.310
0.320
0.125
28
0.180
–
A1
A2
B
3.556
0.559
1.651
1.016
0.508
0.331
35.179
33.020
8.382
7.493
2.540
7.874
9.652
3.683
28
0.140
0.022
0.065
0.040
0.020
0.013
1.395
1.300
0.330
0.295
0.100
0.310
0.380
0.145
28
B1
B2
B3
C
Typical
4 places
4 places
Typical
Typical
4 places
4 places
Typical
D
34.163
33.020
7.874
7.112
2.540
7.874
8.128
3.175
28
D1
E
Reference
Reference
E1
e1
eA
eB
L
Typical
Typical
Reference
Reference
N
S
0.584
1.220
0.023
0.048
DS30234D-page 292
1997 Microchip Technology Inc.
PIC16C6X
25.3
40-Lead Plastic Dual In-line (600 mil) (P)
N
α
E1
E
C
eA
eB
Pin No. 1
Indicator
Area
D
S
S1
e1
Base
Plane
Seating
Plane
L
B1
B
A
A2
A1
D1
Package Group: Plastic Dual In-Line (PLA)
Millimeters
Inches
Symbol
Min
Max
Notes
Min
Max
Notes
α
0°
10°
5.080
–
0°
10°
0.200
–
A
–
–
A1
A2
B
0.381
3.175
0.355
1.270
0.203
0.015
0.125
0.014
0.050
0.008
2.015
1.900
0.600
0.530
0.098
0.600
0.600
0.115
40
4.064
0.559
1.778
0.381
52.197
48.260
15.875
13.970
2.591
15.240
17.272
3.683
40
0.160
0.022
0.070
0.015
2.055
1.900
0.625
0.550
0.102
0.600
0.680
0.145
40
B1
C
Typical
Typical
Typical
Typical
D
51.181
48.260
15.240
13.462
2.489
15.240
15.240
2.921
40
D1
E
Reference
Reference
E1
e1
eA
eB
L
Typical
Typical
Reference
Reference
N
S
1.270
0.508
–
0.050
0.020
–
S1
–
–
1997 Microchip Technology Inc.
DS30234D-page 293
PIC16C6X
25.4
18-Lead Plastic Surface Mount (SOIC - Wide, 300 mil Body) (SO)
e
B
N
h x 45°
Index
Area
E
H
α
C
Chamfer
h x 45°
L
1
2
3
D
Base
Plane
CP
Seating
Plane
A1
A
Package Group: Plastic SOIC (SO)
Millimeters
Max
Inches
Symbol
Min
0°
Notes
Min
Max
Notes
α
A
8°
0°
8°
2.362
0.101
0.355
0.241
11.353
7.416
1.270
10.007
0.381
0.406
18
2.642
0.300
0.483
0.318
11.735
7.595
1.270
10.643
0.762
1.143
18
0.093
0.004
0.014
0.009
0.447
0.292
0.050
0.394
0.015
0.016
18
0.104
0.012
0.019
0.013
0.462
0.299
0.050
0.419
0.030
0.045
18
A1
B
C
D
E
e
Reference
Reference
H
h
L
N
CP
–
0.102
–
0.004
DS30234D-page 294
1997 Microchip Technology Inc.
PIC16C6X
25.5
28-Lead Plastic Surface Mount (SOIC - Wide, 300 mil Body) (SO)
e
B
h x 45°
N
Index
Area
E
H
α
C
Chamfer
h x 45°
L
1
2
3
D
Base
Plane
CP
Seating
Plane
A1
A
Package Group: Plastic SOIC (SO)
Millimeters
Max
Inches
Symbol
Min
0°
Notes
Min
Max
Notes
α
A
8°
0°
8°
2.362
0.101
0.355
0.241
17.703
7.416
1.270
10.007
0.381
0.406
28
2.642
0.300
0.483
0.318
18.085
7.595
1.270
10.643
0.762
1.143
28
0.093
0.004
0.014
0.009
0.697
0.292
0.050
0.394
0.015
0.016
28
0.104
0.012
0.019
0.013
0.712
0.299
0.050
0.419
0.030
0.045
28
A1
B
C
D
E
e
Typical
Typical
H
h
L
N
CP
–
0.102
–
0.004
1997 Microchip Technology Inc.
DS30234D-page 295
PIC16C6X
25.6
18-Lead Ceramic CERDIP Dual In-line with Window (300 mil) (JW)
N
α
C
E1
E
eA
eB
Pin No. 1
Indicator
Area
D
S
S1
e1
Base
Plane
Seating
Plane
L
B1
B
A
A3
A2
A1
D1
Package Group: Ceramic CERDIP Dual In-Line (CDP)
Millimeters
Inches
Max
Symbol
Min
Max
Notes
Min
Notes
α
0°
10°
0°
10°
A
—
5.080
1.778
4.699
4.445
0.585
1.651
0.381
23.622
20.320
8.382
7.874
2.540
8.128
10.160
3.810
18
—
0.200
0.070
0.185
0.175
0.023
0.065
0.015
0.930
0.800
0.330
0.310
0.100
0.320
0.400
0.150
18
A1
A2
A3
B
0.381
3.810
3.810
0.355
1.270
0.203
22.352
20.320
7.620
5.588
2.540
7.366
7.620
3.175
18
0.015
0.150
0.150
0.014
0.050
0.008
0.880
0.800
0.300
0.220
0.100
0.290
0.300
0.125
18
B1
C
Typical
Typical
Typical
Typical
D
D1
E
Reference
Reference
E1
e1
eA
eB
L
Reference
Typical
Reference
Typical
N
S
0.508
0.381
1.397
1.270
0.020
0.015
0.055
0.050
S1
DS30234D-page 296
1997 Microchip Technology Inc.
PIC16C6X
25.7
28-Lead Ceramic CERDIP Dual In-line with Window (300 mil)) (JW)
N
E1
E
α
C
Pin No. 1
Indicator
Area
eA
eB
D
D1
e1
Base
Plane
Seating
Plane
L
B1
B
A
A2
A1
D2
Package Group: Ceramic CERDIP Dual In-Line (CDP)
Millimeters
Inches
Symbol
Min
Max
Notes
Min
Max
Notes
α
0°
3.30
0.38
2.92
0.35
1.14
0.20
34.54
32.97
7.62
6.10
2.54
7.62
—
10°
5.84
—
0°
10°
A
.130
0.230
—
A1
A2
B
0.015
0.115
0.014
0.045
0.008
1.360
1.298
0.300
0.240
0.100
0.300
—
4.95
0.58
1.78
0.38
37.72
33.07
8.25
7.87
2.54
7.62
11.43
5.08
28
0.195
0.023
0.070
0.015
1.485
1.302
0.325
0.310
0.100
0.300
0.450
0.200
28
B1
C
Typical
Typical
Typical
Typical
D
D2
E
Reference
Reference
E1
e
Typical
Typical
eA
eB
L
Reference
Reference
2.92
28
0.115
28
N
D1
0.13
—
0.005
—
1997 Microchip Technology Inc.
DS30234D-page 297
PIC16C6X
25.8
40-Lead Ceramic CERDIP Dual In-line with Window (600 mil) (JW)
N
E1
E
α
C
Pin No. 1
Indicator
Area
eA
eB
D
S
S1
e1
Base
Plane
Seating
Plane
L
B1
B
A
A3
A2
A1
D1
Package Group: Ceramic CERDIP Dual In-Line (CDP)
Millimeters
Inches
Max
Symbol
Min
Max
Notes
Min
Notes
α
0°
10°
0°
10°
A
4.318
0.381
3.810
3.810
0.355
1.270
0.203
5.715
1.778
4.699
4.445
0.585
1.651
0.381
52.705
48.260
15.875
15.240
2.540
16.002
18.034
3.810
40
0.170
0.015
0.150
0.150
0.014
0.050
0.008
2.025
1.900
0.600
0.510
0.100
0.590
0.600
0.125
40
0.225
0.070
0.185
0.175
0.023
0.065
0.015
2.075
1.900
0.625
0.600
0.100
0.630
0.710
0.150
40
A1
A2
A3
B
B1
C
Typical
Typical
Typical
Typical
D
51.435
48.260
15.240
12.954
2.540
14.986
15.240
3.175
40
D1
E
Reference
Reference
E1
e1
eA
eB
L
Reference
Typical
Reference
Typical
N
S
1.016
0.381
2.286
1.778
0.040
0.015
0.090
0.070
S1
DS30234D-page 298
1997 Microchip Technology Inc.
PIC16C6X
25.9
28-Lead Ceramic Side Brazed Dual In-Line with Window (300 mil) (JW)
N
C
E1 E
eA
eB
α
Pin #1
Indicator Area
D
S1
S
Base
Plane
Seating
Plane
A3
A2
A
L
A1
B1
e1
B
D1
Package Group: Ceramic Side Brazed Dual In-Line (CER)
Millimeters
Max
Inches
Max
Symbol
Min
Notes
Min
Notes
α
0°
10°
5.030
1.524
3.506
2.388
0.508
1.321
0.305
35.916
33.147
8.128
7.620
2.667
7.874
8.179
4.064
28
0°
10°
A
3.937
1.016
2.921
1.930
0.406
1.219
0.228
35.204
32.893
7.620
7.366
2.413
7.366
7.594
3.302
28
0.155
0.040
0.115
0.076
0.016
0.048
0.009
1.386
1.295
0.300
0.290
0.095
0.290
0.299
0.130
28
0.198
0.060
0.138
0.094
0.020
0.052
0.012
1.414
1.305
0.320
0.300
0.105
0.310
0.322
0.160
28
A1
A2
A3
B
B1
C
Typical
Typical
D
D1
E
Reference
E1
e1
eA
eB
L
Typical
Reference
N
S
1.143
0.533
1.397
0.737
0.045
0.021
0.055
0.029
S1
1997 Microchip Technology Inc.
DS30234D-page 299
PIC16C6X
25.10 28-Lead Plastic Surface Mount (SSOP - 209 mil Body 5.30 mm) (SS)
N
Index
area
E
H
α
C
L
1 2 3
e
B
A
Base plane
CP
Seating plane
D
A1
Package Group: Plastic SSOP
Millimeters
Max
Inches
Max
Symbol
Min
Notes
Min
Notes
α
A
0°
8°
0°
8°
1.730
0.050
0.250
0.130
10.070
5.200
0.650
7.650
0.550
28
1.990
0.210
0.380
0.220
10.330
5.380
0.650
7.900
0.950
28
0.068
0.002
0.010
0.005
0.396
0.205
0.026
0.301
0.022
28
0.078
0.008
0.015
0.009
0.407
0.212
0.026
0.311
0.037
28
A1
B
C
D
E
e
Reference
Reference
H
L
N
CP
-
0.102
-
0.004
DS30234D-page 300
1997 Microchip Technology Inc.
PIC16C6X
25.11 44-Lead Plastic Leaded Chip Carrier (Square) (PLCC)
D
0.812/0.661
N Pics
.032/.026
1.27
.050
2 Sides
0.177
.007
S
B D-E S
-A-
0.177
.007
2 Sides
-H-
B A S
9
S
A
D1
A1
-D-
3
D3/E3
D2
0.101
.004
Seating
Plane
D
0.38
.015
-C-
F-G
E2
S
S
3
-G-
4
4
3
-F-
8
E1
E
0.38
.015
F-G
-B-
-E-
3
0.177
.007
A F-G S
S
10
0.812/0.661
.032/.026
3
0.254
.010
0.254
.010
11
Max
Max
11
1.524
.060
0.508
.020
0.508
.020
Min
-H-
2
-H-
2
6
6
-C-
5
1.651
.065
1.651
.065
0.64
.025
0.533/0.331
.021/.013
Min
R
R
1.14/0.64
.045/.025
1.14/0.64
.045/.025
0.177
.007
D-E S
F-G S ,
A
M
Package Group: Plastic Leaded Chip Carrier (PLCC)
Millimeters
Inches
Max
Symbol
Min
Max
Notes
Min
Notes
A
A1
D
4.191
2.413
17.399
16.510
15.494
12.700
17.399
16.510
15.494
12.700
44
4.572
2.921
0.165
0.095
0.685
0.650
0.610
0.500
0.685
0.650
0.610
0.500
44
0.180
0.115
0.695
0.656
0.630
0.500
0.695
0.656
0.630
0.500
44
17.653
16.663
16.002
12.700
17.653
16.663
16.002
12.700
44
D1
D2
D3
E
Reference
Reference
Reference
Reference
E1
E2
E3
N
CP
LT
–
0.102
–
0.004
0.015
0.203
0.381
0.008
1997 Microchip Technology Inc.
DS30234D-page 301
PIC16C6X
25.12 44-Lead Plastic Surface Mount (MQFP 10x10 mm Body 1.6/0.15 mm Lead Form) (PQ)
0.20 M C A-B S D S
D
4
0.20 M H A-B S D S
0.05 mm/mm A-B
D1
5
7
0.20 min.
D3
0.13 R min.
Index
area
6
PARTING
LINE
0.13/0.30 R
b
α
9
L
C
E3
E1
E
1.60 Ref.
0.20 M C A-B S D S
4
TYP 4x
10
0.20 M H A-B S D S
0.05 mm/mm D
5
7
e
B
A2
A
Base
Plane
Seating
Plane
A1
Package Group: Plastic MQFP
Millimeters
Max
Inches
Max
Symbol
Min
Notes
Min
Notes
α
A
0°
7°
0°
7°
2.000
0.050
1.950
0.300
0.150
12.950
9.900
8.000
12.950
9.900
8.000
0.800
0.730
44
2.350
0.250
2.100
0.450
0.180
13.450
10.100
8.000
13.450
10.100
8.000
0.800
1.030
44
0.078
0.002
0.768
0.011
0.006
0.510
0.390
0.315
0.510
0.390
0.315
0.031
0.028
44
0.093
0.010
0.083
0.018
0.007
0.530
0.398
0.315
0.530
0.398
0.315
0.032
0.041
44
A1
A2
b
Typical
Typical
C
D
D1
D3
E
Reference
Reference
Reference
Reference
E1
E3
e
L
N
CP
0.102
–
0.004
–
DS30234D-page 302
1997 Microchip Technology Inc.
PIC16C6X
25.13 44-Lead Plastic Surface Mount (TQFP 10x10 mm Body 1.0/0.10 mm Lead Form) (TQ)
D
D1
1.0ø (0.039ø) Ref.
11°/13°(4x)
0° Min
Pin#1
2
Pin#1
2
E
E1
Θ
11°/13°(4x)
Detail B
e
3.0ø (0.118ø) Ref.
R1 0.08 Min
R 0.08/0.20
Option 1 (TOP side)
Option 2 (TOP side)
Gage Plane
0.250
A1
Base Metal
Lead Finish
b
A2
A
S
0.20
Min
L
L
c
c1
L1
Detail A
Detail B
1.00 Ref
1.00 Ref.
b1
Detail A
Detail B
Package Group: Plastic TQFP
Millimeters
Max
Inches
Max
Symbol
Min
Notes
Min
Notes
A
A1
A2
D
1.00
0.05
0.95
11.75
9.90
11.75
9.90
0.45
1.20
0.15
0.039
0.002
0.037
0.463
0.390
0.463
0.390
0.018
0.047
0.006
0.041
0.482
0.398
0.482
0.398
0.030
1.05
12.25
10.10
12.25
10.10
0.75
D1
E
E1
L
e
0.80 BSC
0.031 BSC
b
0.30
0.30
0.09
0.09
44
0.45
0.40
0.20
0.16
44
0.012
0.012
0.004
0.004
44
0.018
0.016
0.008
0.006
44
b1
c
c1
N
Θ
0°
7°
0°
7°
Note 1: Dimensions D1 and E1 do not include mold protrusion. Allowable mold protrusion is 0.25m/m (0.010”) per
side. D1 and E1 dimensions including mold mismatch.
2: Dimension “b” does not include Dambar protrusion, allowable Dambar protrusion shall be 0.08m/m
(0.003”)max.
3: This outline conforms to JEDEC MS-026.
1997 Microchip Technology Inc.
DS30234D-page 303
PIC16C6X
25.14 Package Marking Information
18-Lead PDIP
Example
PIC16C61-04/P
9450CBA
MMMMMMMMMMMMM
XXXXXXXXXXXXXXXX
AABBCDE
18-Lead SOIC
Example
MMMMMMMMMM
XXXXXXXXXXXX
XXXXXXXXXXXX
PIC16C61
-20/SO
AABBCDE
9449CBA
18-Lead CERDIP Windowed
Example
MMMMMM
XXXXXXXX
AABBCDE
PIC16C61
/JW
9440CBT
28-Lead PDIP (.300 MIL)
Example
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
PIC16C63-04I/SP
9452CAN
AABBCAE
Legend:
MM...M
XX...X
AA
Microchip part number information
Customer specific information*
Year code (last 2 digits of calender year)
Week code (week of January 1 is week '01’)
BB
C
Facility code of the plant at which wafer is manufactured.
C = Chandler, Arizona, U.S.A.
S = Tempe, Arizona, U.S.A.
D
D
E
Mask revision number for microcontroller
1
2
Mask revision number for EEPROM
Assembly code of the plant or country of origin in which
part was assembled.
In the event the full Microchip part number cannot be marked on one
line, it will be carried over to the next line thus limiting the number of
available characters for customer specific information.
Note:
*
Standard OTP marking consists of Microchip part number, year code, week code,
facility code, mask revision number, and assembly code. For OTP marking beyond
this, certain price adders apply. Please check with your Microchip Sales Office.
For QTP devices, any special marking adders are included in QTP price.
DS30234D-page 304
1997 Microchip Technology Inc.
PIC16C6X
Package Marking Information (Cont’d)
28-Lead SOIC
Example
PIC16C62-20/S0111
MMMMMMMMMMMMMMMMMMXX
XXXXXXXXXXXXXXXXXXXX
AABBCAE
9515SBA
28-Lead CERDIP Skinny Windowed
Example
XXXXXXXXXXXXXX
XXXXXXXXXXXXXX
AABBCDE
PIC16C62/JW
9517SBT
28-Lead Side Brazed Skinny Windowed
Example
XXXXXXXXXXX
XXXXXXXXXXX
AABBCDE
PIC16C66/JW
9517CAT
28-Lead SSOP
Example
PIC16C62
XXXXXXXXXXXX
XXXXXXXXXXXX
20I/SS025
AABBCAE
9517SBP
Example
40-Lead PDIP
PIC16C65-04/P
MMMMMMMMMMMMMM
XXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXX
AABBCDE
9510CAA
Legend:
MM...M
XX...X
AA
Microchip part number information
Customer specific information*
Year code (last 2 digits of calender year)
Week code (week of January 1 is week '01’)
BB
C
Facility code of the plant at which wafer is manufactured.
C = Chandler, Arizona, U.S.A.
S = Tempe, Arizona, U.S.A.
D
E
Mask revision number for microcontroller
1
Assembly code of the plant or country of origin in which
part was assembled.
In the event the full Microchip part number cannot be marked on one
line, it will be carried over to the next line thus limiting the number of
available characters for customer specific information.
Note:
*
Standard OTP marking consists of Microchip part number, year code, week code,
facility code, mask revision number, and assembly code. For OTP marking beyond
this, certain price adders apply. Please check with your Microchip Sales Office.
For QTP devices, any special marking adders are included in QTP price.
1997 Microchip Technology Inc.
DS30234D-page 305
PIC16C6X
Package Marking Information (Cont’d)
40-Lead CERDIP Windowed
Example
PIC16C67/JW
9450CAT
MMMMMMMMM
XXXXXXXXXXX
XXXXXXXXXXX
AABBCDE
44-Lead PLCC
Example
MMMMMMMM
PIC16C64
XXXXXXXXXX
XXXXXXXXXX
AABBCDE
-20/L
9442CAN
44-Lead MQFP
Example
MMMMMMMM
XXXXXXXXXX
XXXXXXXXXX
PIC16C64
-04/PQ
AABBCDE
9444CAP
44-Lead TQFP
Example
MMMMMMMM
XXXXXXXXXX
XXXXXXXXXX
PIC16C64A
-10/TQ
AABBCDE
AABBCDE
Legend:
MM...M
Microchip part number information
Customer specific information*
XX...X
AA
Year code (last 2 digits of calender year)
Week code (week of January 1 is week '01’)
BB
C
Facility code of the plant at which wafer is manufactured.
C = Chandler, Arizona, U.S.A.
S = Tempe, Arizona, U.S.A.
D
E
Mask revision number for microcontroller
1
Assembly code of the plant or country of origin in which
part was assembled.
In the event the full Microchip part number cannot be marked on one
line, it will be carried over to the next line thus limiting the number of
available characters for customer specific information.
Note:
*
Standard OTP marking consists of Microchip part number, year code, week code,
facility code, mask revision number, and assembly code. For OTP marking beyond
this, certain price adders apply. Please check with your Microchip Sales Office.
For QTP devices, any special marking adders are included in QTP price.
DS30234D-page 306
1997 Microchip Technology Inc.
PIC16C6X
APPENDIX A:MODIFICATIONS
APPENDIX B:COMPATIBILITY
The following are the list of modifications over the
PIC16C5X microcontroller family:
To convert code written for PIC16C5X to PIC16CXX,
the user should take the following steps:
1. Instruction word length is increased to 14-bits.
This allows larger page sizes both in program
memory (2K now as opposed to 512 before) and
register file (128 bytes now versus 32 bytes
before).
1. Remove any program memory page select
operations (PA2, PA1, PA0 bits) for CALL,
GOTO.
2. Revisit any computed jump operations (write to
PC or add to PC, etc.) to make sure page bits
are set properly under the new scheme.
2. A PC high latch register (PCLATH) is added to
handle program memory paging. PA2, PA1, PA0
bits are removed from STATUS register.
3. Eliminate any data memory page switching.
Redefine data variables to reallocate them.
3. Data memory paging is redefined slightly. STA-
TUS register is modified.
4. Verify all writes to STATUS, OPTION, and FSR
registers since these have changed.
4. Four new instructions have been added:
RETURN, RETFIE, ADDLW, and SUBLW.
Two instructions TRIS and OPTION are being
phased out although they are kept for compati-
bility with PIC16C5X.
5. Change reset vector to 0000h.
5. OPTION and TRIS registers are made address-
able.
6. Interrupt capability is added. Interrupt vector is
at 0004h.
7. Stack size is increased to 8 deep.
8. Reset vector is changed to 0000h.
9. Reset of all registers is revisited. Five different
reset (and wake-up) types are recognized. Reg-
isters are reset differently.
10. Wake-up from SLEEP through interrupt is
added.
11. Two separate timers, Oscillator Start-up Timer
(OST) and Power-up Timer (PWRT), are
included for more reliable power-up. These tim-
ers are invoked selectively to avoid unnecessary
delays on power-up and wake-up.
12. PORTB has weak pull-ups and interrupt on
change feature.
13. Timer0 pin is also a port pin (RA4/T0CKI) now.
14. FSR is made a full 8-bit register.
15. “In-circuit programming” is made possible. The
user can program PIC16CXX devices using only
five pins: VDD, VSS, VPP, RB6 (clock) and RB7
(data in/out).
16. Power Control register (PCON) is added with a
Power-on Reset status bit (POR).(Not on the
PIC16C61).
17. Brown-out Reset has been added to the follow-
ing devices:
PIC16C62A/R62/63/R63/64A/R64/65A/R65/66/
67.
1997 Microchip Technology Inc.
DS30234D-page 307
PIC16C6X
APPENDIX C:WHAT’S NEW
APPENDIX D:WHAT’S CHANGED
Added PIC16CR63 and PIC16CR65 devices.
Minor changes, spelling and grammatical changes.
Added PIC16C66 and PIC16C67 devices. The
PIC16C66/67 devices have 368 bytes of data memory
distributed in 4 banks and 8K of program memory in 4
pages. These two devices have an enhanced SPI that
supports both clock phase and polarity. The USART
has been enhanced.
Divided SPI section into SPI for the PIC16C66/67
(Section 11.3) and SPI for all other devices
(Section 11.2).
Added the following note for the USART.This applies to
all devices except the PIC16C66 and PIC16C67.
For the PIC16C63/R63/65/65A/R65 the asynchronous
high speed mode (BRGH = 1) may experience a high
rate of receive errors. It is recommended that BRGH =
0. If you desire a higher baud rate than BRGH = 0 can
support, refer to the device errata for additional infor-
mation or use the PIC16C66/67.
When upgrading to the PIC16C66/67 please note that
the upper 16 bytes of data memory in banks 1,2, and 3
are mapped into bank 0. This may require relocation of
data memory usage in the user application code.
Q-cycles for instruction execution were added to Sec-
tion 14.0 Instruction Set Summary.
DS30234D-page 308
1997 Microchip Technology Inc.
PIC16C6X
APPENDIX E: PIC16/17 MICROCONTROLLERS
E.1
PIC12CXXX Family of Devices
PIC12C508
PIC12C509
PIC12C671
PIC12C672
Maximum Frequency
of Operation (MHz)
4
4
4
4
Clock
EPROM Program Memory
Data Memory (bytes)
Timer Module(s)
512 x 12
25
1024 x 12
41
1024 x 14
128
2048 x 14
128
Memory
TMR0
—
TMR0
—
TMR0
4
TMR0
4
Peripherals
A/D Converter (8-bit) Channels
Wake-up from SLEEP on
pin change
Yes
Yes
Yes
Yes
I/O Pins
5
5
5
5
Input Pins
1
1
1
1
Internal Pull-ups
Voltage Range (Volts)
In-Circuit Serial Programming
Number of Instructions
Packages
Yes
Yes
Yes
Yes
Features
2.5-5.5
2.5-5.5
2.5-5.5
2.5-5.5
Yes
Yes
Yes
Yes
33
33
35
35
8-pin DIP, SOIC
8-pin DIP, SOIC
8-pin DIP, SOIC
8-pin DIP, SOIC
All PIC12C5XX devices have Power-on Reset, selectable Watchdog Timer, selectable code protect and high I/O current capability.
All PIC12C5XX devices use serial programming with data pin GP1 and clock pin GP0.
E.2
PIC14C000 Family of Devices
PIC14C000
Clock
Maximum Frequency of Operation (MHz) 20
EPROM Program Memory (x14 words)
Data Memory (bytes)
4K
192
Memory
Timer Module(s)
TMR0
ADTMR
2
Serial Port(s)
(SPI/I C, USART)
I C with SMBus
Peripherals
2
Support
Slope A/D Converter Channels
Interrupt Sources
8 External; 6 Internal
11
I/O Pins
22
Voltage Range (Volts)
In-Circuit Serial Programming
Additional On-chip Features
2.7-6.0
Yes
Features
Internal 4MHz Oscillator, Bandgap Reference,Temperature Sensor,
Calibration Factors, Low Voltage Detector, SLEEP, HIBERNATE,
Comparators with Programmable References (2)
Packages
28-pin DIP (.300 mil), SOIC, SSOP
1997 Microchip Technology Inc.
DS30234D-page 309
PIC16C6X
E.3
PIC16C15X Family of Devices
PIC16C154 PIC16CR154 PIC16C156 PIC16CR156 PIC16C158 PIC16CR158
Maximum Frequency
of Operation (MHz)
20
20
20
1K
—
20
20
2K
—
20
Clock
EPROM Program Memory 512
(x12 words)
—
—
—
Memory
ROM Program Memory
(x12 words)
—
512
1K
2K
RAM Data Memory (bytes) 25
25
25
25
73
73
Peripherals Timer Module(s)
TMR0
12
TMR0
12
TMR0
12
TMR0
12
TMR0
12
TMR0
12
I/O Pins
Voltage Range (Volts)
3.0-5.5
33
2.5-5.5
33
3.0-5.5
33
2.5-5.5
33
3.0-5.5
33
2.5-5.5
33
Number of Instructions
Packages
Features
18-pin DIP, 18-pin DIP,
SOIC; SOIC;
18-pin DIP, 18-pin DIP,
SOIC; SOIC;
18-pin DIP,
SOIC;
18-pin DIP,
SOIC;
20-pin SSOP 20-pin SSOP 20-pin SSOP 20-pin SSOP 20-pin SSOP 20-pin SSOP
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer, selectable code protect and high
I/O current capability.
E.4
PIC16C5X Family of Devices
PIC16C52
PIC16C54
20
PIC16C54A PIC16CR54A PIC16C55
PIC16C56
20
Maximum Frequency
of Operation (MHz)
4
20
20
20
Clock
EPROM Program Memory
(x12 words)
384
—
512
—
512
—
—
512
—
1K
—
Memory
ROM Program Memory
(x12 words)
512
RAM Data Memory (bytes) 25
25
25
25
24
25
Peripherals Timer Module(s)
TMR0
12
TMR0
12
TMR0
12
TMR0
12
TMR0
20
TMR0
12
I/O Pins
Voltage Range (Volts)
2.5-6.25
33
2.5-6.25
33
2.0-6.25
33
2.0-6.25
33
2.5-6.25
33
2.5-6.25
33
Number of Instructions
Packages
Features
18-pin DIP, 18-pin DIP,
SOIC SOIC;
18-pin DIP,
SOIC;
18-pin DIP,
SOIC;
28-pin DIP, 18-pin DIP,
SOIC,
SOIC;
20-pin SSOP 20-pin SSOP 20-pin SSOP SSOP
20-pin SSOP
PIC16C57
PIC16CR57B
PIC16C58A
PIC16CR58A
Maximum Frequency
of Operation (MHz)
20
2K
—
20
—
20
2K
—
20
—
Clock
EPROM Program Memory
(x12 words)
Memory
ROM Program Memory
(x12 words)
2K
72
2K
73
RAM Data Memory (bytes)
72
73
Peripherals Timer Module(s)
TMR0
20
TMR0
20
TMR0
12
TMR0
12
I/O Pins
Voltage Range (Volts)
2.5-6.25
33
2.5-6.25
33
2.0-6.25
33
2.5-6.25
33
Number of Instructions
Packages
Features
28-pin DIP,
SOIC,
28-pin DIP, SOIC, 18-pin DIP, SOIC; 18-pin DIP, SOIC;
SSOP 20-pin SSOP 20-pin SSOP
SSOP
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer (except PIC16C52), selectable code protect and high
I/O current capability.
DS30234D-page 310
1997 Microchip Technology Inc.
PIC16C6X
E.5
PIC16C55X Family of Devices
(1)
PIC16C554
PIC16C556
PIC16C558
Clock
Maximum Frequency of Operation (MHz)
EPROM Program Memory (x14 words)
Data Memory (bytes)
20
20
1K
80
20
512
80
2K
128
Memory
Timer Module(s)
TMR0
—
TMR0
—
TMR0
—
Peripherals Comparators(s)
Internal Reference Voltage
—
—
—
Interrupt Sources
I/O Pins
3
3
3
13
13
13
Voltage Range (Volts)
Brown-out Reset
Packages
2.5-6.0
—
2.5-6.0
—
2.5-6.0
—
Features
18-pin DIP,
SOIC;
18-pin DIP,
SOIC;
18-pin DIP,
SOIC;
20-pin SSOP
20-pin SSOP
20-pin SSOP
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer, selectable code protect and high
I/O current capability. All PIC16C5XX Family devices use serial programming with clock pin RB6 and data pin RB7.
Note 1: Please contact your local Microchip sales office for availability of these devices.
E.6
PIC16C62X and PIC16C64X Family of Devices
PIC16C620
PIC16C621
20
PIC16C622
20
PIC16C642
20
PIC16C662
20
Maximum Frequency
of Operation (MHz)
20
Clock
EPROM Program Memory
(x14 words)
512
1K
2K
4K
4K
Memory
Data Memory (bytes)
Timer Module(s)
80
80
128
TMR0
2
176
TMR0
2
176
TMR0
2
TMR0
2
TMR0
2
Peripherals Comparators(s)
Internal Reference Voltage
Yes
4
Yes
4
Yes
4
Yes
4
Yes
5
Interrupt Sources
I/O Pins
13
13
13
22
33
Voltage Range (Volts)
Brown-out Reset
Packages
2.5-6.0
Yes
2.5-6.0
Yes
2.5-6.0
Yes
3.0-6.0
Yes
3.0-6.0
Yes
Features
18-pin DIP,
SOIC;
18-pin DIP,
SOIC;
18-pin DIP,
SOIC;
28-pin PDIP, 40-pin PDIP,
SOIC,
Windowed
CDIP;
44-pin PLCC,
MQFP
20-pin SSOP 20-pin SSOP 20-pin SSOP Windowed
CDIP
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer, selectable code protect and high
I/O current capability. All PIC16C62X and PIC16C64X Family devices use serial programming with clock pin RB6 and data pin RB7.
1997 Microchip Technology Inc.
DS30234D-page 311
PIC16C6X
E.7
PIC16C7XX Family of Devces
(1)
PIC16C710 PIC16C71 PIC16C711 PIC16C715
PIC16C72 PIC16CR72
Maximum Frequency
of Operation (MHz)
20
20
1K
—
20
1K
—
20
2K
—
20
20
Clock
EPROM Program Memory
(x14 words)
512
—
2K
—
—
Memory
ROM Program Memory
(14K words)
2K
128
Data Memory (bytes)
Timer Module(s)
36
36
68
128
128
TMR0
TMR0
TMR0
TMR0
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
Capture/Compare/
PWM Module(s)
—
—
—
—
—
—
—
—
—
1
1
Peripherals
2
2
Serial Port(s)
SPI/I C
SPI/I C
2
(SPI/I C, USART)
Parallel Slave Port
—
—
—
—
—
A/D Converter (8-bit) Channels 4
4
4
4
5
5
Interrupt Sources
I/O Pins
4
4
4
4
8
8
13
13
13
13
22
22
Voltage Range (Volts)
3.0-6.0
3.0-6.0
Yes
—
3.0-6.0
Yes
Yes
3.0-5.5
Yes
Yes
2.5-6.0
Yes
Yes
3.0-5.5
Yes
Yes
In-Circuit Serial Programming Yes
Features
Brown-out Reset
Packages
Yes
18-pin DIP, 18-pin DIP, 18-pin DIP, 18-pin DIP, 28-pin SDIP, 28-pin SDIP,
SOIC;
SOIC
SOIC;
SOIC;
SOIC, SSOP SOIC, SSOP
20-pin SSOP
20-pin SSOP 20-pin SSOP
PIC16C73A
PIC16C74A
PIC16C76
PIC16C77
Maximum Frequency of Oper- 20
ation (MHz)
20
20
20
Clock
EPROM Program Memory
(x14 words)
4K
4K
192
8K
8K
368
Memory
Data Memory (bytes)
Timer Module(s)
192
368
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
Capture/Compare/PWM Mod-
ule(s)
2
2
2
2
Peripherals
2
2
2
2
2
Serial Port(s) (SPI/I C, US- SPI/I C, USART
ART)
SPI/I C, USART
SPI/I C, USART
SPI/I C, USART
Parallel Slave Port
—
Yes
8
—
Yes
8
A/D Converter (8-bit) Channels 5
5
Interrupt Sources
I/O Pins
11
12
11
12
22
33
22
33
Voltage Range (Volts)
2.5-6.0
2.5-6.0
Yes
Yes
2.5-6.0
Yes
Yes
2.5-6.0
Yes
Yes
In-Circuit Serial Programming Yes
Features
Brown-out Reset
Packages
Yes
28-pin SDIP,
SOIC
40-pin DIP;
44-pin PLCC,
MQFP, TQFP
28-pin SDIP,
SOIC
40-pin DIP;
44-pin PLCC,
MQFP, TQFP
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer, selectable code protect and high I/O current capabil-
ity. All PIC16C7XX Family devices use serial programming with clock pin RB6 and data pin RB7.
Note 1: Please contact your local Microchip sales office for availability of these devices.
DS30234D-page 312
1997 Microchip Technology Inc.
PIC16C6X
E.8
PIC16C8X Family of Devices
PIC16F83
PIC16CR83
PIC16F84
PIC16CR84
Maximum Frequency
of Operation (MHz)
10
10
10
10
Clock
Flash Program Memory
EEPROM Program Memory
ROM Program Memory
Data Memory (bytes)
512
—
—
—
1K
—
—
1K
68
64
—
Memory
—
512
36
—
36
64
68
Data EEPROM (bytes)
64
64
Peripher-
als
Timer Module(s)
TMR0
TMR0
TMR0
TMR0
Interrupt Sources
I/O Pins
4
4
4
4
13
13
13
13
Features
Voltage Range (Volts)
Packages
2.0-6.0
2.0-6.0
2.0-6.0
2.0-6.0
18-pin DIP,
SOIC
18-pin DIP,
SOIC
18-pin DIP,
SOIC
18-pin DIP,
SOIC
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer, selectable code protect and high I/O current capabil-
ity. All PIC16C8X Family devices use serial programming with clock pin RB6 and data pin RB7.
E.9
PIC16C9XX Family Of Devices
PIC16C923
PIC16C924
Clock
Maximum Frequency of Operation (MHz)
EPROM Program Memory
Data Memory (bytes)
8
8
4K
176
4K
176
Memory
Timer Module(s)
TMR0,
TMR1,
TMR2
TMR0,
TMR1,
TMR2
Capture/Compare/PWM Module(s)
Serial Port(s)
(SPI/I C, USART)
1
1
2
2
SPI/I C
SPI/I C
Peripherals
2
Parallel Slave Port
—
—
—
5
A/D Converter (8-bit) Channels
LCD Module
4 Com,
32 Seg
4 Com,
32 Seg
Interrupt Sources
I/O Pins
8
9
25
25
Input Pins
27
27
Voltage Range (Volts)
In-Circuit Serial Programming
Brown-out Reset
Packages
3.0-6.0
Yes
—
3.0-6.0
Yes
—
Features
(1)
(1)
64-pin SDIP
TQFP;
,
64-pin SDIP
TQFP;
,
68-pin PLCC,
Die
68-pin PLCC,
Die
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer, selectable code protect and high I/O current capa-
bility. All PIC16C9XX Family devices use serial programming with clock pin RB6 and data pin RB7.
1997 Microchip Technology Inc.
DS30234D-page 313
PIC16C6X
E.10
PIC17CXXX Family of Devices
PIC17C42A
33
PIC17CR42
33
PIC17C43
PIC17CR43
33
PIC17C44
Maximum Frequency
of Operation (MHz)
33
4K
—
33
8K
—
Clock
EPROM Program Memory
(words)
2K
—
—
—
Memory
ROM Program Memory
(words)
2K
232
4K
454
RAM Data Memory (bytes)
Timer Module(s)
232
454
454
TMR0,
TMR1,
TMR2,
TMR3
TMR0,
TMR1,
TMR2,
TMR3
TMR0,
TMR1,
TMR2,
TMR3
TMR0,
TMR1,
TMR2,
TMR3
TMR0,
TMR1,
TMR2,
TMR3
Peripherals
Captures/PWM Module(s)
Serial Port(s) (USART)
Hardware Multiply
External Interrupts
Interrupt Sources
I/O Pins
2
2
2
2
2
Yes
Yes
Yes
11
Yes
Yes
Yes
11
Yes
Yes
Yes
11
Yes
Yes
Yes
11
Yes
Yes
Yes
11
33
33
33
33
33
Features
Voltage Range (Volts)
Number of Instructions
Packages
2.5-6.0
58
2.5-6.0
58
2.5-6.0
58
2.5-6.0
58
2.5-6.0
58
40-pin DIP;
40-pin DIP;
40-pin DIP;
40-pin DIP;
40-pin DIP;
44-pin PLCC,
44-pin PLCC,
44-pin PLCC,
44-pin PLCC,
44-pin PLCC,
MQFP, TQFP MQFP, TQFP MQFP, TQFP MQFP, TQFP MQFP, TQFP
PIC17C752
33
PIC17C756
33
Maximum Frequency
of Operation (MHz)
Clock
EPROM Program Memory
(words)
8K
—
16K
—
Memory
ROM Program Memory
(words)
RAM Data Memory (bytes)
Timer Module(s)
454
902
TMR0,
TMR1,
TMR2,
TMR3
TMR0,
TMR1,
TMR2,
TMR3
Peripherals
Captures/PWM Module(s)
Serial Port(s) (USART)
Hardware Multiply
External Interrupts
Interrupt Sources
I/O Pins
4/3
2
4/3
2
Yes
Yes
18
Yes
Yes
18
50
50
Features
Voltage Range (Volts)
Number of Instructions
Packages
3.0-6.0
58
3.0-6.0
58
64-pin DIP;
68-pin LCC,
68-pin TQFP
64-pin DIP;
68-pin LCC,
68-pin TQFP
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer, selectable code protect and high
I/O current capability.
DS30234D-page 314
1997 Microchip Technology Inc.
PIC16C6X
PIN COMPATIBILITY
Devices that have the same package type and VDD,
VSS and MCLR pin locations are said to be pin
compatible. This allows these different devices to
operate in the same socket. Compatible devices may
only requires minor software modification to allow
proper operation in the application socket
(ex., PIC16C56 and PIC16C61 devices). Not all
devices in the same package size are pin compatible;
for example, the PIC16C62 is compatible with the
PIC16C63, but not the PIC16C55.
Pin compatibility does not mean that the devices offer
the same features. As an example, the PIC16C54 is
pin compatible with the PIC16C71, but does not have
an A/D converter, weak pull-ups on PORTB, or
interrupts.
TABLE E-1:
PIN COMPATIBLE DEVICES
Pin Compatible Devices
Package
PIC12C508, PIC12C509, PIC12C671, PIC12C672
8-pin
PIC16C154, PIC16CR154, PIC16C156,
PIC16CR156, PIC16C158, PIC16CR158,
PIC16C52, PIC16C54, PIC16C54A,
PIC16CR54A,
18-pin,
20-pin
PIC16C56,
PIC16C58A, PIC16CR58A,
PIC16C61,
PIC16C554, PIC16C556, PIC16C558
PIC16C620, PIC16C621, PIC16C622
PIC16C641, PIC16C642, PIC16C661, PIC16C662
PIC16C710, PIC16C71, PIC16C711, PIC16C715
PIC16F83, PIC16CR83,
PIC16F84A, PIC16CR84
PIC16C55, PIC16C57, PIC16CR57B
28-pin
28-pin
PIC16CR62, PIC16C62A, PIC16C63, PIC16CR63,
PIC16C66, PIC16C72, PIC16C73A, PIC16C76
PIC16CR64, PIC16C64A, PIC16C65A,
PIC16CR65, PIC16C67, PIC16C74A, PIC16C77
40-pin
40-pin
PIC17CR42, PIC17C42A,
PIC17C43, PIC17CR43, PIC17C44
PIC16C923, PIC16C924
PIC17C756, PIC17C752
64/68-pin
64/68-pin
1997 Microchip Technology Inc.
DS30234D-page 315
PIC16C6X
NOTES:
DS30234D-page 316
1997 Microchip Technology Inc.
PIC16C6X
SPI Master/Slave Connection......................................87
SSP in I C Mode .........................................................99
INDEX
2
SSP in SPI Mode...................................................86, 91
Timer0 .........................................................................65
Timer0/WDT Prescaler................................................68
Timer1 .........................................................................72
Timer2 .........................................................................75
USART Receive ........................................................114
USART Transmit .......................................................112
Watchdog Timer ........................................................140
BOR...................................................................................129
BOR.............................................................................47, 131
BRGH ................................................................................105
Brown-out Reset (BOR).....................................................129
Brown-out Reset Status bit, BOR........................................47
Buffer Full Status bit, BF................................................84, 89
Numerics
9-bit Receive Enable bit, RX9........................................... 106
9-bit Transmit Enable bit, TX9 .......................................... 105
9th bit of received data, RX9D.......................................... 106
9th bit of transmit data, TX9D ........................................... 105
A
Absolute Maximum
Ratings.............................. 163, 183, 199, 215, 231, 247, 263
ACK..................................................................... 96, 100, 101
ALU....................................................................................... 9
Application Notes
AN552 (Implementing Wake-up on Key Stroke)......... 53
AN556 (Implementing a Table Read) ......................... 48
AN594 (Using the CCP Modules) ............................... 77
Architectural Overview.......................................................... 9
C
C..........................................................................................35
C Compiler.........................................................................161
Capture
Block Diagram .............................................................78
Mode............................................................................78
Pin Configuration.........................................................78
Prescaler .....................................................................79
Software Interrupt........................................................78
Capture Interrupt .................................................................78
Capture/Compare/PWM (CCP)
B
Baud Rate Formula........................................................... 107
Baud Rate Generator........................................................ 107
Baud Rates
Asynchronous Mode ................................................. 108
Error, Calculating ...................................................... 107
RX Pin Sampling, Timing Diagrams.................. 110, 111
Sampling................................................................... 110
Synchronous Mode................................................... 108
BF ......................................................................... 84, 89, 100
Block Diagrams
Capture Mode..............................................................78
Capture Mode Block Diagram .....................................78
CCP1...........................................................................77
CCP2...........................................................................77
Compare Mode............................................................79
Compare Mode Block Diagram ...................................79
Overview......................................................................63
Prescaler .....................................................................79
PWM Block Diagram ...................................................80
PWM Mode..................................................................80
PWM, Example Frequencies/Resolutions ...................81
Section.........................................................................77
Carry......................................................................................9
Carry bit...............................................................................35
CCP Module Interaction ......................................................77
CCP pin Configuration.........................................................78
CCP to Timer Resource Use...............................................77
CCP1 Interrupt Enable bit, CCP1IE.....................................38
CCP1 Interrupt Flag bit, CCP1IF.........................................41
CCP1 Mode Select bits .......................................................78
CCP1CON.............................................24, 26, 28, 30, 32, 34
CCP1IE................................................................................38
CCP1IF................................................................................41
CCP1M3:CCM1M0..............................................................78
CCP1X:CCP1Y....................................................................78
CCP2 Interrupt Enable bit, CCP2IE.....................................45
CCP2 Interrupt Flag bit, CCP2IF.........................................46
CCP2 Mode Select bits .......................................................78
CCP2CON.............................................24, 26, 28, 30, 32, 34
CCP2IE................................................................................45
CCP2IF................................................................................46
CCP2M3:CCP2M0 ..............................................................78
CCP2X:CCP2Y....................................................................78
CCPR1H................................................24, 26, 28, 30, 32, 34
CCPR1L ................................................24, 26, 28, 30, 32, 34
CCPR2H................................................24, 26, 28, 30, 32, 34
CCPR2L ................................................24, 26, 28, 30, 32, 34
CKE .....................................................................................89
CKP ...............................................................................85, 90
Capture Mode Operation ............................................ 78
Compare Mode ........................................................... 79
Crystal Oscillator, Ceramic Resonator...................... 125
External Brown-out Protection .................................. 135
External Parallel Resonant Crystal Circuit................ 127
External Power-on Reset.......................................... 135
External Series Resonant Crystal Circuit.................. 127
2
I C Mode..................................................................... 99
In-circuit Programming Connections......................... 142
Interrupt Logic........................................................... 137
On-chip Reset Circuit................................................ 128
Parallel Slave Port, PORTD-PORTE .......................... 61
PIC16C61 ................................................................... 10
PIC16C62 ................................................................... 11
PIC16C62A................................................................. 11
PIC16C63 ................................................................... 12
PIC16C64 ................................................................... 11
PIC16C64A................................................................. 11
PIC16C65 ................................................................... 12
PIC16C65A................................................................. 12
PIC16C66 ................................................................... 13
PIC16C67 ................................................................... 13
PIC16CR62................................................................. 11
PIC16CR63................................................................. 12
PIC16CR64................................................................. 11
PIC16CR65................................................................. 12
PORTC ....................................................................... 55
PORTD (I/O Mode) ..................................................... 57
PORTE (I/O Mode) ..................................................... 58
PWM ........................................................................... 80
RA3:RA0 pins ............................................................. 51
RA4/T0CKI pin............................................................ 51
RA5 pin ....................................................................... 51
RB3:RB0 pins ............................................................. 54
RB7:RB4 pins ....................................................... 53, 54
RC Oscillator Mode................................................... 127
1997 Microchip Technology Inc.
DS30234D-page 317
PIC16C6X
Clearing Interrupts............................................................... 53
Clock Polarity Select bit, CKP....................................... 85, 90
Clock Polarity, SPI Mode .................................................... 87
Clock Source Select bit, CSRC......................................... 105
Clocking Scheme ................................................................ 18
Code Examples
44-Lead Plastic Surface Mount (MQFP
10x10 mm Body 1.6/0.15 mm Lead Form)....... 302, 303
Device Varieties.................................................................... 7
Digit Carry............................................................................. 9
Digit Carry bit...................................................................... 35
Direct Addressing ............................................................... 49
Changing Between Capture Prescalers...................... 79
Ensuring Interrupts are Globally Disabled ................ 136
Indirect Addressing ..................................................... 49
Initializing PORTA....................................................... 51
Initializing PORTB....................................................... 53
Initializing PORTC....................................................... 55
Loading the SSPBUF Register ................................... 86
Loading the SSPBUF register..................................... 91
Reading a 16-bit Free-running Timer.......................... 73
Read-Modify-Write on an I/O Port............................... 60
Saving Status, W, and PCLATH Registers............... 139
Subroutine Call, Page0 to Page1................................ 49
Code Protection ................................................................ 142
Compare
Block Diagram............................................................. 79
Mode........................................................................... 79
Pin Configuration ........................................................ 79
Software Interrupt ....................................................... 79
Special Event Trigger.................................................. 79
Computed GOTO................................................................ 48
Configuration Bits.............................................................. 123
Configuration Word, Diagram............................................ 124
Connecting Two Microcontrollers........................................ 87
Continuous Receive Enable bit, CREN............................. 106
CREN................................................................................ 106
CSRC................................................................................ 105
E
Electrical Characteristics .. 163, 183, 199, 215, 231, 247, 263
External Clock Synchronization, TMR0 .............................. 67
F
Family of Devices
PIC12CXXX.............................................................. 309
PIC14C000............................................................... 309
PIC16C15X............................................................... 310
PIC16C55X............................................................... 311
PIC16C5X................................................................. 310
PIC16C62X and PIC16C64X.................................... 311
PIC16C6X..................................................................... 6
PIC16C7XX .............................................................. 312
PIC16C8X................................................................. 313
PIC16C9XX .............................................................. 313
PIC17CXX ................................................................ 314
FERR................................................................................ 106
Framing Error bit, FERR................................................... 106
FSR......................... 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34
Fuzzy Logic Dev. System (fuzzyTECH -MP)........... 159, 161
G
General Description.............................................................. 5
General Purpose Registers ................................................ 20
GIE...................................................................................... 37
Global Interrupt Enable bit, GIE.......................................... 37
Graphs
D
D/A ................................................................................ 84, 89
Data/Address bit, D/A.................................................... 84, 89
Data Memory
PIC16C6X................................................................. 281
PIC16C61................................................................. 173
Organization................................................................ 20
Section........................................................................ 20
Data Sheet
H
High Baud Rate Select bit, BRGH .................................... 105
Compatibility ............................................................. 307
Modifications............................................................. 307
What’s New............................................................... 308
DC....................................................................................... 35
DC CHARACTERISTICS..164, 184, 200, 216, 232, 248, 264
Development Support ....................................................... 159
Development Tools ........................................................... 159
Device Drawings
I
I/O Ports, Section................................................................ 51
2
I C
Addressing................................................................ 100
Addressing I C Devices.............................................. 96
2
Arbitration ................................................................... 98
Block Diagram ............................................................ 99
Clock Synchronization................................................ 98
Combined Format....................................................... 97
18-Lead Ceramic CERDIP Dual In-line
with Window (300 mil)............................................... 296
18-Lead Plastic Dual In-line (300 mil)....................... 291
18-Lead Plastic Surface Mount
2
I C Operation.............................................................. 99
2
I C Overview .............................................................. 95
Initiating and Terminating Data Transfer .................... 95
Master Mode............................................................. 103
Master-Receiver Sequence........................................ 97
Master-Transmitter Sequence.................................... 97
Mode........................................................................... 99
Mode Selection........................................................... 99
Multi-master................................................................ 98
Multi-Master Mode.................................................... 103
Reception ................................................................. 101
Reception Timing Diagram....................................... 101
SCL and SDA pins.................................................... 100
Slave Mode............................................................... 100
START........................................................................ 95
STOP.................................................................... 95, 96
(SOIC - Wide, 300 mil Body).................................... 294
28-Lead Ceramic CERDIP Dual In-line with
Window (300 mil))..................................................... 297
28-Lead Ceramic Side Brazed Dual In-Line
with Window (300 mil)............................................... 299
28-Lead Plastic Dual In-line (300 mil)....................... 292
28-Lead Plastic Surface Mount
(SOIC - Wide, 300 mil Body)..................................... 295
28-Lead Plastic Surface Mount
(SSOP - 209 mil Body 5.30 mm)............................... 300
40-Lead Ceramic CERDIP Dual In-line
with Window (600 mil)............................................... 298
40-Lead Plastic Dual In-line (600 mil)....................... 293
44-Lead Plastic Leaded Chip Carrier (Square)......... 301
DS30234D-page 318
1997 Microchip Technology Inc.
PIC16C6X
Transfer Acknowledge ................................................ 96
Transmission............................................................. 102
ID Locations...................................................................... 142
IDLE_MODE ..................................................................... 104
In-circuit Serial Programming............................................ 142
INDF...................................................... 24, 26, 28, 30, 32, 34
Indirect Addressing ............................................................. 49
Instruction Cycle ................................................................. 18
Instruction Flow/Pipelining .................................................. 18
Instruction Format............................................................. 143
Instruction Set
RB0/INT Timing Diagram ..........................................138
Receive Flag bit...........................................................42
Timer0 .........................................................................65
Timer0, Timing.............................................................66
Timing Diagram, Wake-up from SLEEP....................142
TMR0.........................................................................138
USART Receive Enable bit .........................................39
USART Transmit Enable bit ........................................39
USART Transmit Flag bit.............................................42
Wake-up ....................................................................141
Wake-up from SLEEP ...............................................141
INTF.....................................................................................37
IRP.......................................................................................35
ADDLW..................................................................... 145
ADDWF..................................................................... 145
ANDLW..................................................................... 145
ANDWF..................................................................... 145
BCF........................................................................... 146
BSF........................................................................... 146
BTFSC ...................................................................... 146
BTFSS ...................................................................... 147
CALL......................................................................... 147
CLRF......................................................................... 148
CLRW ....................................................................... 148
CLRWDT................................................................... 148
COMF ....................................................................... 149
DECF ........................................................................ 149
DECFSZ.................................................................... 149
GOTO ....................................................................... 150
INCF.......................................................................... 150
INCFSZ..................................................................... 151
IORLW ...................................................................... 151
IORWF...................................................................... 152
MOVF........................................................................ 152
MOVLW .................................................................... 152
MOVWF .................................................................... 152
NOP .......................................................................... 153
OPTION .................................................................... 153
RETFIE ..................................................................... 153
RETLW ..................................................................... 154
RETURN................................................................... 154
RLF ........................................................................... 155
RRF........................................................................... 155
SLEEP ...................................................................... 156
SUBLW ..................................................................... 156
SUBWF..................................................................... 157
SWAPF ..................................................................... 157
TRIS.......................................................................... 157
XORLW..................................................................... 158
XORWF..................................................................... 158
Section...................................................................... 143
Summary Table......................................................... 144
INTCON .................. 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34
INTE.................................................................................... 37
INTEDG .............................................................................. 36
Interrupt Edge Select bit, INTEDG...................................... 36
Interrupt on Change Feature............................................... 53
Interrupts
L
Loading the Program Counter .............................................48
M
MPASM Assembler ...................................................159, 160
MPLAB-C...........................................................................161
MPSIM Software Simulator .......................................159, 161
O
OERR ................................................................................106
One-Time-Programmable Devices........................................7
OPCODE...........................................................................143
Open-Drain..........................................................................51
OPTION.................................................25, 27, 29, 31, 33, 34
Oscillator Start-up Timer (OST).................................123, 129
Oscillators
Block Diagram, External Parallel Resonant Crystal ..127
Capacitor Selection .....................................................73
Configuration .............................................................125
External Crystal Circuit..............................................127
HS......................................................................125, 130
LP ......................................................................125, 130
RC, Block Diagram....................................................127
RC, Section ...............................................................127
XT..............................................................................125
Overrun Error bit, OERR ...................................................106
P
P ....................................................................................84, 89
Packaging Information.......................................................291
Parallel Slave Port
PORTD........................................................................57
Section.........................................................................61
Parallel Slave Port Interrupt Flag bit, PSPIF .......................43
Parallel Slave Port Read/Write Interrupt Enable bit, PSPIE 39
PCL..........................24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34
PCLATH ............24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 48
PCON ............................................25, 27, 29, 31, 33, 34, 130
PD................................................................................35, 131
PEIE ....................................................................................37
Peripheral Interrupt Enable bit, PEIE...................................37
PICDEM-1 Low-Cost PIC16/17 Demo Board............159, 160
PICDEM-2 Low-Cost PIC16CXX Demo Board..........159, 160
PICDEM-3 Low-Cost PIC16C9XXX Demo Board .............160
PICMASTER In-Circuit Emulator.......................................159
PICSTART Low-Cost Development System .....................159
PIE1.......................................................25, 27, 29, 31, 33, 34
PIE2.......................................................25, 27, 29, 31, 33, 34
Pin Compatible Devices ....................................................315
Pin Functions
Section...................................................................... 136
CCP ............................................................................ 78
CCP1 .......................................................................... 38
CCP1 Flag bit.............................................................. 41
CCP2 Enable bit ......................................................... 45
CCP2 Flag bit.............................................................. 46
Context Saving.......................................................... 139
Parallel Slave Port Flag bit.......................................... 43
Parallel Slave Prot Read/Write Enable bit .................. 39
Port RB ....................................................................... 53
RB0/INT .............................................................. 54, 138
MCLR/VPP ...................................................................16
1997 Microchip Technology Inc.
DS30234D-page 319
PIC16C6X
OSC1/CLKIN............................................................... 16
OSC2/CLKOUT........................................................... 16
PORTA........................................................................ 52
PORTB........................................................................ 54
PORTC ....................................................................... 55
PORTD ....................................................................... 57
PORTE........................................................................ 59
RA4/T0CKI............................................................ 16, 52
RA5/SS ................................................................. 16, 52
RB0/INT ................................................................ 16, 54
RB6........................................................................... 142
RB7........................................................................... 142
RC0/T1OSI/T1CKI ...................................................... 55
RC0/T1OSO/T1CKI .............................................. 16, 55
RC1/T1OSI ................................................................. 55
RC1/T1OSI/CCP2................................................. 16, 55
RC1/T1OSO................................................................ 55
RC2/CCP1 ...................................................... 16, 55, 56
RC3/SCK/SCL ................................................ 16, 55, 56
RC4/SDI/SDA ................................................. 16, 55, 56
RC5/SDO........................................................ 16, 55, 56
RC6/TX/CK .....................................16, 55, 56, 105–120
RC7/RX/DT.....................................16, 55, 56, 105–120
RD7/PSP7:RD0/PSP0 .......................................... 17, 57
RE0/RD........................................................... 17, 59, 61
RE1/WR.......................................................... 17, 59, 61
RE2/CS........................................................... 17, 59, 61
SCK....................................................................... 86–88
SDI........................................................................ 86–88
SDO ...................................................................... 86–88
SS ......................................................................... 86–88
VDD ............................................................................. 17
VSS.............................................................................. 17
PIR1 ......................................................24, 26, 28, 30, 32, 34
PIR2 ......................................................24, 26, 28, 30, 32, 34
POP..................................................................................... 48
POR ............................................................................ 47, 131
POR Time-Out Sequence on Power-Up ........................... 134
Port RB Interrupt ................................................................. 53
PORTA............................................24, 26, 28, 30, 32, 34, 51
PORTB............................................24, 26, 28, 30, 32, 34, 53
PORTB Interrupt on Change............................................. 138
PORTB Pull-up Enable bit, RBPU....................................... 36
PORTC............................................24, 26, 28, 30, 32, 34, 55
PORTD............................................24, 26, 28, 30, 32, 34, 57
PORTE............................................24, 26, 28, 30, 32, 34, 58
Ports
Bi-directional ............................................................... 60
I/O Programming Considerations................................ 60
PORTA........................................................................ 16
PORTB........................................................................ 16
PORTC ....................................................................... 16
PORTD ....................................................................... 17
PORTE........................................................................ 17
Successive Operations on an I/O Port........................ 60
Power/Control Status Register, PCON ............................. 130
Power-down bit ................................................................... 35
Power-down Mode ............................................................ 141
Power-on Reset (POR) ..................................................... 129
Power-on Reset Status bit, POR......................................... 47
Power-up Timer (PWRT)........................................... 123, 129
PR2 .......................................................25, 27, 29, 31, 33, 34
Prescaler............................................................................. 68
Prescaler Assignment bit, PSA ........................................... 36
Prescaler Rate Select bits, PS2:PS0 .................................. 36
PRO MATE Universal Programmer .................................. 159
Program Memory
Map....................................................................... 19, 20
Organization ............................................................... 19
Paging ........................................................................ 48
Section........................................................................ 19
Programming While In-circuit............................................ 142
PS2:PS0 ............................................................................. 36
PSA..................................................................................... 36
PSPIE ................................................................................. 39
PSPIF ................................................................................. 43
Pull-ups............................................................................... 53
PUSH.................................................................................. 48
PWM
Block Diagram ............................................................ 80
Calculations................................................................ 81
Mode........................................................................... 80
Output Timing............................................................. 80
PWM Least Significant bits................................................. 78
Q
Quadrature Clocks.............................................................. 18
Quick-Turnaround-Production .............................................. 7
R
R/W bit............................................ 84, 89, 96, 100, 101, 102
RA0 pin............................................................................... 51
RA1 pin............................................................................... 51
RA2 pin............................................................................... 51
RA3 pin............................................................................... 51
RA4/T0CKI pin.................................................................... 51
RA5 pin............................................................................... 51
RB Port Change Interrupt Enable bit, RBIE........................ 37
RB Port Change Interrupt Flag bit, RBIF ............................ 37
RB0..................................................................................... 54
RB0/INT............................................................................ 138
RB0/INT External Interrupt Enable bit, INTE ...................... 37
RB0/INT External Interrupt Flag bit, INTF........................... 37
RB1..................................................................................... 54
RB2..................................................................................... 54
RB3..................................................................................... 54
RB4..................................................................................... 53
RB5..................................................................................... 53
RB6..................................................................................... 53
RB7..................................................................................... 53
RBIE ................................................................................... 37
RBIF.................................................................................... 37
RBPU............................................................................ 36, 53
RC Oscillator..................................................................... 130
RCIE ................................................................................... 39
RCIF ................................................................................... 42
RCREG................................................. 24, 26, 28, 30, 32, 34
RCSTA.......................................... 24, 26, 28, 30, 32, 34, 106
RCV_MODE ..................................................................... 104
Read Only Memory............................................................... 7
Read/Write bit Information, R/W................................... 84, 89
Receive and Control Register........................................... 106
Receive Overflow Detect bit, SSPOV................................. 85
Receive Overflow Indicator bit, SSPOV.............................. 90
Register Bank Select bit, Indirect........................................ 35
Register Bank Select bits. Direct ........................................ 35
DS30234D-page 320
1997 Microchip Technology Inc.
PIC16C6X
Registers
PORTD
CCP1CON
Diagram .............................................................. 78
Section ................................................................57
Summary.................................................28, 30, 32
Section................................................................ 78
Summary .................................... 24, 26, 28, 30, 32
PORTE
Section ................................................................58
Summary.................................................28, 30, 32
CCP2CON
Diagram .............................................................. 78
Section................................................................ 78
Summary ................................................ 26, 30, 32
PR2
Summary.....................................25, 27, 29, 31, 33
RCREG
Summary.................................................26, 30, 32
RCSTA
Diagram.............................................................106
Summary.................................................26, 30, 32
SPBRG
Summary.................................................27, 31, 33
SSPBUF
CCPR1H
Summary .................................... 24, 26, 28, 30, 32
CCPR1L
Summary .................................... 24, 26, 28, 30, 32
CCPR2H
Summary ................................................ 26, 30, 32
CCPR2L
Summary ................................................ 26, 30, 32
Section ................................................................86
Summary.....................................24, 26, 28, 30, 32
FSR
Indirect Addressing............................................. 49
Summary .............................. 24, 26, 28, 30, 32, 34
SSPCON
Diagram...............................................................85
Summary.....................................24, 26, 28, 30, 32
INDF
Indirect Addressing............................................. 49
Summary .............................. 24, 26, 28, 30, 32, 34
SSPSR
Section ................................................................86
SSPSTAT ....................................................................89
Diagram...............................................................84
Section ................................................................84
Summary.....................................25, 27, 29, 31, 33
STATUS
INTCON
Diagram .............................................................. 37
Section................................................................ 37
Summary .............................. 24, 26, 28, 30, 32, 34
OPTION
Diagram .............................................................. 36
Section................................................................ 36
Summary .............................. 25, 27, 29, 31, 33, 34
Diagram...............................................................35
Section ................................................................35
Summary...............................24, 26, 28, 30, 32, 34
T1CON
PCL
Section................................................................ 48
Summary .............................. 24, 26, 28, 30, 32, 34
PCLATH
Section................................................................ 48
Summary .............................. 24, 26, 28, 30, 32, 34
PCON
Diagram .............................................................. 47
Diagram...............................................................71
Section ................................................................71
Summary.....................................24, 26, 28, 30, 32
T2CON
Diagram...............................................................75
Section ................................................................75
Summary.....................................24, 26, 28, 30, 32
TMR0
Summary...............................24, 26, 28, 30, 32, 34
TMR1H
Summary.....................................24, 26, 28, 30, 32
TMR1L
Summary.....................................24, 26, 28, 30, 32
TMR2...........................................................................75
Summary.....................................24, 26, 28, 30, 32
TRISA
Section ................................................................51
Summary.....................................25, 27, 29, 31, 33
TRISB
Section ................................................................53
Summary...............................25, 27, 29, 31, 33, 34
TRISC
Section................................................................ 47
Summary .................................... 25, 27, 29, 31, 33
PIE1
PIE2
PIR1
PIR2
Diagram .............................................................. 40
Section................................................................ 38
Summary .................................... 25, 27, 29, 31, 33
Diagram .............................................................. 45
Section................................................................ 45
Summary ................................................ 27, 31, 33
Diagram .............................................................. 44
Section................................................................ 41
Summary .................................... 24, 26, 28, 30, 32
Diagram .............................................................. 46
Section................................................................ 46
Summary ................................................ 26, 30, 32
Section ................................................................55
Summary.....................................25, 27, 29, 31, 33
TRISD
Section ................................................................57
Summary.................................................29, 31, 33
TRISE
Diagram...............................................................58
Section ................................................................58
Summary.................................................29, 31, 33
TXREG
PORTA
Section................................................................ 51
Summary .................................... 24, 26, 28, 30, 32
PORTB
Section................................................................ 53
Summary .............................. 24, 26, 28, 30, 32, 34
PORTC
Section................................................................ 55
Summary .................................... 24, 26, 28, 30, 32
Summary.................................................26, 30, 32
1997 Microchip Technology Inc.
DS30234D-page 321
PIC16C6X
2
2
TXSTA
SSP in I C Mode - See I C
Diagram ............................................................ 105
Section.............................................................. 105
Summary....................................................... 31, 33
SSPADD......................................... 25, 27, 29, 31, 33, 34, 99
SSPBUF ......................................... 24, 26, 28, 30, 32, 34, 99
SSPCON................................... 24, 26, 28, 30, 32, 34, 85, 90
SSPEN.......................................................................... 85, 90
SSPIE ................................................................................. 38
SSPIF ................................................................................. 41
SSPM3:SSPM0 ............................................................ 85, 90
SSPOV ................................................................. 85, 90, 100
SSPSTAT ................................. 25, 27, 29, 31, 33, 34, 84, 99
SSPSTAT Register............................................................. 89
Stack................................................................................... 48
Start bit, S..................................................................... 84, 89
STATUS.................. 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34
Status bits................................................................. 130, 131
Status Bits During Various Resets.................................... 131
Stop bit, P ..................................................................... 84, 89
Switching Prescalers .......................................................... 69
SYNC,USART Mode Select bit, SYNC............................. 105
Synchronizing Clocks, TMR0.............................................. 67
Synchronous Serial Port (SSP)
W................................................................................... 9
Special Function Registers, Initialization
Conditions................................................................. 132
Special Function Registers, Reset Conditions.......... 131
Special Function Register Summary...24, 26, 28, 30, 32
File Maps .................................................................... 21
Resets............................................................................... 128
ROM...................................................................................... 7
RP0 bit .......................................................................... 20, 35
RP1 ..................................................................................... 35
RX9 ................................................................................... 106
RX9D................................................................................. 106
S
S.................................................................................... 84, 89
SCI - See Universal Synchronous Asynchronous Receiver
Transmitter (USART)
SCK..................................................................................... 86
SCL ................................................................................... 100
SDI ...................................................................................... 86
SDO .................................................................................... 86
Serial Port Enable bit, SPEN............................................. 106
Serial Programming .......................................................... 142
Serial Programming, Block Diagram................................. 142
Serialized Quick-Turnaround-Production.............................. 7
Single Receive Enable bit, SREN ..................................... 106
Slave Mode
Block Diagram, SPI Mode .......................................... 86
SPI Master/Slave Diagram ......................................... 87
SPI Mode.................................................................... 86
Synchronous Serial Port Enable bit, SSPEN................ 85, 90
Synchronous Serial Port Interrupt Enable bit, SSPIE......... 38
Synchronous Serial Port Interrupt Flag bit, SSPIF ............. 41
Synchronous Serial Port Mode Select bits,
SSPM3:SSPM0 ............................................................ 85, 90
Synchronous Serial Port Module ........................................ 83
Synchronous Serial Port Status Register ........................... 89
SCL........................................................................... 100
SDA........................................................................... 100
SLEEP Mode............................................................. 123, 141
SMP .................................................................................... 89
Software Simulator (MPSIM)............................................. 161
SPBRG..................................................25, 27, 29, 31, 33, 34
Special Features, Section ................................................. 123
SPEN ................................................................................ 106
SPI
Block Diagram....................................................... 86, 91
Master Mode............................................................... 92
Master Mode Timing ................................................... 93
Mode........................................................................... 86
Serial Clock................................................................. 91
Serial Data In .............................................................. 91
Serial Data Out ........................................................... 91
Slave Mode Timing ..................................................... 94
Slave Mode Timing Diagram....................................... 93
Slave Select................................................................ 91
SPI clock..................................................................... 92
SPI Mode .................................................................... 91
SSPCON..................................................................... 90
SSPSTAT.................................................................... 89
SPI Clock Edge Select bit, CKE.......................................... 89
SPI Data Input Sample Phase Select bit, SMP................... 89
SPI Mode ............................................................................ 86
SREN ................................................................................ 106
SS ....................................................................................... 86
SSP
T
T0CS................................................................................... 36
T0IE .................................................................................... 37
T0IF .................................................................................... 37
T0SE................................................................................... 36
T1CKPS1:T1CKPS0........................................................... 71
T1CON.................................................. 24, 26, 28, 30, 32, 34
T1OSCEN........................................................................... 71
T1SYNC.............................................................................. 71
T2CKPS1:T2CKPS0........................................................... 75
T2CON............................................ 24, 26, 28, 30, 32, 34, 75
TIme-out ........................................................................... 130
Time-out bit......................................................................... 35
Time-out Sequence .......................................................... 130
Timer Modules
Overview, all............................................................... 63
Timer0
Block Diagram .................................................... 65
Counter Mode..................................................... 65
External Clock .................................................... 67
Interrupt .............................................................. 65
Overview............................................................. 63
Prescaler ............................................................ 68
Section................................................................ 65
Timer Mode ........................................................ 65
Timing DiagramTiiming Diagrams
Timer0 ................................................................ 65
TMR0 register..................................................... 65
Timer1
Module Overview ........................................................ 83
Section........................................................................ 83
SSPBUF...................................................................... 92
SSPCON..................................................................... 90
SSPSR........................................................................ 92
SSPSTAT.................................................................... 89
Block Diagram .................................................... 72
Capacitor Selection ............................................ 73
Counter Mode, Asynchronous............................ 73
Counter Mode, Synchronous.............................. 72
External Clock .................................................... 73
Oscillator............................................................. 73
DS30234D-page 322
1997 Microchip Technology Inc.
PIC16C6X
Overview............................................................. 63
Prescaler............................................................. 72
Read/Write in Asynchronous Counter Mode ...... 73
Section................................................................ 71
Synchronizing with External Clock...................... 72
Timer Mode......................................................... 72
TMR1 Register Pair ............................................ 71
Watchdog Timer................................................207
PIC16C63
Brown-out Reset................................................239
Capture/Compare/PWM....................................241
CLKOUT and I/O...............................................238
External Clock ...................................................237
2
I C Bus Data .....................................................245
2
Timer2
I C Bus Start/Stop Bits......................................244
Block Diagram .................................................... 75
Overview............................................................. 63
Postscaler........................................................... 75
Prescaler............................................................. 75
Timer0 Clock Synchronization, Delay................................. 67
TImer0 Interrupt ................................................................ 138
Timer1 Clock Source Select bit, TMR1CS.......................... 71
Timer1 External Clock Input Synchronization
Control bit, T1SYNC ........................................................... 71
Timer1 Input Clock Prescale Select bits ............................. 71
Timer1 Mode Selection....................................................... 78
Timer1 On bit, TMR1ON..................................................... 71
Timer1 Oscillator Enable Control bit, T1OSCEN ................ 71
Timer2 Clock Prescale Select bits,
T2CKPS1:T2CKPS0........................................................... 75
Timer2 Module.................................................................... 75
Timer2 On bit, TMR2ON..................................................... 75
Timer2 Output Postscale Select bits,
TOUTPS3:TOUTPS0.......................................................... 75
Timing Diagrams
Oscillator Start-up Timer ...................................239
Power-up Timer.................................................239
Reset.................................................................239
SPI Mode...........................................................243
Timer0 ...............................................................240
Timer1 ...............................................................240
USART Synchronous Receive
(Master/Slave)..................................................246
Watchdog Timer................................................239
PIC16C64
Capture/Compare/PWM....................................193
CLKOUT and I/O...............................................190
External Clock ...................................................189
2
I C Bus Data .....................................................197
2
I C Bus Start/Stop Bits......................................196
Oscillator Start-up Timer ...................................191
Parallel Slave Port.............................................194
Power-up Timer.................................................191
Reset.................................................................191
SPI Mode...........................................................195
Timer0 ...............................................................192
Timer1 ...............................................................192
Watchdog Timer................................................191
Brown-out Reset ....................................................... 129
2
I C Clock Synchronization .......................................... 98
2
I C Data Transfer Wait State ...................................... 96
2
PIC16C64A
I C Multi-Master Arbitration......................................... 98
2
Brown-out Reset................................................207
Capture/Compare/PWM....................................209
CLKOUT and I/O...............................................206
External Clock ...................................................205
I C Reception (7-bit Address)................................... 101
PIC16C61
CLKOUT and I/O .............................................. 170
External Clock................................................... 169
Oscillator Start-up Timer................................... 171
Power-up Timer ................................................ 171
Reset ................................................................ 171
Timer0............................................................... 172
Watchdog Timer ............................................... 171
PIC16C62
2
I C Bus Data .....................................................213
2
I C Bus Start/Stop Bits......................................212
Oscillator Start-up Timer ...................................207
Parallel Slave Port.............................................210
Power-up Timer.................................................207
Reset.................................................................207
SPI Mode...........................................................211
Timer0 ...............................................................208
Timer1 ...............................................................208
Watchdog Timer................................................207
Capture/Compare/PWM ................................... 193
CLKOUT and I/O .............................................. 190
External Clock................................................... 189
2
I C Bus Data..................................................... 197
2
PIC16C65
I C Bus Start/Stop Bits ..................................... 196
Capture/Compare/PWM....................................225
CLKOUT and I/O...............................................222
External Clock ...................................................221
Oscillator Start-up Timer................................... 191
Power-up Timer ................................................ 191
Reset ................................................................ 191
SPI Mode.......................................................... 195
Timer0............................................................... 192
Timer1............................................................... 192
Watchdog Timer ............................................... 191
PIC16C62A
2
I C Bus Data .....................................................229
2
I C Bus Start/Stop Bits......................................228
Oscillator Start-up Timer ...................................223
Parallel Slave Port.............................................226
Reset.................................................................223
SPI Mode...........................................................227
Timer0 ...............................................................224
Timer1 ...............................................................224
USART Synchronous Receive
Brown-out Reset............................................... 207
Capture/Compare/PWM ................................... 209
CLKOUT and I/O .............................................. 206
External Clock................................................... 205
2
(Master/Slave)...................................................230
Watchdog Timer................................................223
I C Bus Data..................................................... 213
2
I C Bus Start/Stop Bits ..................................... 212
PIC16C65A
Oscillator Start-up Timer................................... 207
Power-up Timer ................................................ 207
Reset ................................................................ 207
SPI Mode.......................................................... 211
Timer0............................................................... 208
Timer1............................................................... 208
Brown-out Reset................................................239
Capture/Compare/PWM....................................241
CLKOUT and I/O...............................................238
External Clock ...................................................237
2
I C Bus Data .....................................................245
1997 Microchip Technology Inc.
DS30234D-page 323
PIC16C6X
2
I C Bus Start/Stop Bits...................................... 244
PIC16CR63
Brown-out Reset............................................... 255
Oscillator Start-up Timer................................... 239
Parallel Slave Port ............................................ 242
Power-up Timer ................................................ 239
Reset................................................................. 239
SPI Mode .......................................................... 243
Timer0............................................................... 240
Timer1............................................................... 240
USART Synchronous Receive
Capture/Compare/PWM ................................... 257
CLKOUT and I/O .............................................. 254
External Clock .................................................. 253
2
I C Bus Data..................................................... 261
2
I C Bus Start/Stop Bits ..................................... 260
Oscillator Start-up Timer................................... 255
Power-up Timer................................................ 255
Reset ................................................................ 255
SPI Mode.......................................................... 259
Timer0 .............................................................. 256
Timer1 .............................................................. 256
USART Synchronous Receive
(Master/Slave)................................................... 246
Watchdog Timer................................................ 239
PIC16C66
Brown-out Reset ............................................... 271
Capture/Compare/PWM.................................... 273
CLKOUT and I/O............................................... 270
External Clock................................................... 269
(Master/Slave) ................................................. 262
Watchdog Timer ............................................... 255
2
I C Bus Data..................................................... 279
PIC16CR64
2
I C Bus Start/Stop Bits...................................... 278
Capture/Compare/PWM ................................... 209
CLKOUT and I/O .............................................. 206
External Clock .................................................. 205
Oscillator Start-up Timer................................... 271
Power-up Timer ................................................ 271
Reset................................................................. 271
Timer0............................................................... 272
Timer1............................................................... 272
USART Synchronous Receive
2
I C Bus Data..................................................... 213
2
I C Bus Start/Stop Bits ..................................... 212
Oscillator Start-up Timer................................... 207
Parallel Slave Port............................................ 210
Power-up Timer................................................ 207
Reset ................................................................ 207
SPI Mode.......................................................... 211
Timer0 .............................................................. 208
Timer1 .............................................................. 208
Watchdog Timer ............................................... 207
(Master/Slave)................................................... 280
Watchdog Timer................................................ 271
PIC16C67
Brown-out Reset ............................................... 271
Capture/Compare/PWM.................................... 273
CLKOUT and I/O............................................... 270
External Clock................................................... 269
PIC16CR65
2
I C Bus Data..................................................... 279
Brown-out Reset............................................... 255
Capture/Compare/PWM ................................... 257
CLKOUT and I/O .............................................. 254
External Clock .................................................. 253
2
I C Bus Start/Stop Bits...................................... 278
Oscillator Start-up Timer................................... 271
Parallel Slave Port ............................................ 274
Power-up Timer ................................................ 271
Reset................................................................. 271
Timer0............................................................... 272
Timer1............................................................... 272
USART Synchronous Receive
2
I C Bus Data..................................................... 261
2
I C Bus Start/Stop Bits ..................................... 260
Oscillator Start-up Timer................................... 255
Parallel Slave Port............................................ 258
Power-up Timer................................................ 255
Reset ................................................................ 255
SPI Mode.......................................................... 259
Timer0 .............................................................. 256
Timer1 .............................................................. 256
USART Synchronous Receive
(Master/Slave)................................................... 280
Watchdog Timer................................................ 271
PIC16CR62
Capture/Compare/PWM.................................... 209
CLKOUT and I/O............................................... 206
External Clock................................................... 205
(Master/Slave) .................................................. 262
Watchdog Timer ............................................... 255
Power-up Timer........................................................ 223
PWM Output............................................................... 80
RB0/INT Interrupt ..................................................... 138
RX Pin Sampling .............................................. 110, 111
SPI Master Mode........................................................ 93
SPI Mode, Master/Slave Mode,
No SS Control............................................................. 88
SPI Mode, Slave Mode With SS Control .................... 88
SPI Slave Mode (CKE = 1)......................................... 94
SPI Slave Mode Timing (CKE = 0) ............................. 93
Timer0 with External Clock......................................... 67
TMR0 Interrupt Timing................................................ 66
USART Asynchronous Master Transmission ........... 113
USART Asynchronous Master Transmission
2
I C Bus Data..................................................... 213
2
I C Bus Start/Stop Bits...................................... 212
Oscillator Start-up Timer................................... 207
Power-up Timer ................................................ 207
Reset................................................................. 207
SPI Mode .......................................................... 211
Timer0............................................................... 208
Timer1............................................................... 208
Watchdog Timer................................................ 207
(Back to Back) .......................................................... 113
USART Asynchronous Reception ............................ 114
USART Synchronous Reception in
Master Mode............................................................. 119
USART Synchronous Tranmission........................... 117
Wake-up from SLEEP Through Interrupts................ 142
DS30234D-page 324
1997 Microchip Technology Inc.
PIC16C6X
TMR0 .................................................... 24, 26, 28, 30, 32, 34
TMR0 Clock Source Select bit, T0CS................................. 36
TMR0 Interrupt.................................................................... 65
TMR0 Overflow Interrupt Enable bit, T0IE.......................... 37
TMR0 Overflow Interrupt Flag bit, T0IF .............................. 37
TMR0 Prescale Selection Table ......................................... 36
TMR0 Source Edge Select bit, T0SE.................................. 36
TMR1 Overflow Interrupt Enable bit, TMR1IE .................... 38
TMR1 Overflow Interrupt Flag bit, TMR1IF......................... 41
TMR1CS ............................................................................. 71
TMR1H.................................................. 24, 26, 28, 30, 32, 34
TMR1IE............................................................................... 38
TMR1IF............................................................................... 41
TMR1L .................................................. 24, 26, 28, 30, 32, 34
TMR1ON............................................................................. 71
TMR2 .................................................... 24, 26, 28, 30, 32, 34
TMR2 Register.................................................................... 75
TMR2 to PR2 Match Interrupt Enable bit, TMR2IE............. 38
TMR2 to PR2 Match Interrupt Flag bit, TMR2IF ................. 41
TMR2IE............................................................................... 38
TMR2IF............................................................................... 41
TMR2ON............................................................................. 75
TO............................................................................... 35, 131
TOUTPS3:TOUTPS0.......................................................... 75
Transmit Enable bit, TXEN ............................................... 105
Transmit Shift Register Status bit, TRMT ......................... 105
Transmit Status and Control Register............................... 105
TRISA ............................................. 25, 27, 29, 31, 33, 34, 51
TRISB ............................................. 25, 27, 29, 31, 33, 34, 53
TRISC ....................................... 25, 27, 29, 31, 33, 34, 55, 94
TRISD ............................................. 25, 27, 29, 31, 33, 34, 57
TRISE ............................................. 25, 27, 29, 31, 33, 34, 58
TRMT................................................................................ 105
TX9 ................................................................................... 105
TX9D................................................................................. 105
TXEN ................................................................................ 105
TXIE.................................................................................... 39
TXIF .................................................................................... 42
TXREG.................................................. 24, 26, 28, 30, 32, 34
TXSTA .......................................... 25, 27, 29, 31, 33, 34, 105
Synchronous Slave Mode
Reception ..........................................................120
Section ..............................................................120
Setting Up Reception ........................................120
Setting Up Transmission ...................................120
Transmit ............................................................120
Transmit Block Diagram ............................................112
Update Address bit, UA.................................................84, 89
USART Receive Interrupt Enable bit, RCIE ........................39
USART Receive Interrupt Flag bit, RCIF.............................42
USART Transmit Interrupt Enable bit, TXIE........................39
USART Transmit Interrupt Flag bit, TXIF ............................42
UV Erasable Devices.............................................................7
W
Wake-up from Sleep..........................................................141
Wake-up on Key Depression...............................................53
Wake-up Using Interrupts..................................................141
Watchdog Timer (WDT)
Block Diagram ...........................................................140
Period ........................................................................140
Programming Considerations....................................140
Section.......................................................................140
WCOL............................................................................85, 90
Weak Internal Pull-ups ........................................................53
Write Collision Detect bit, WCOL...................................85, 90
X
XMIT_MODE .....................................................................104
XT......................................................................................130
Z
Z ..........................................................................................35
Zero bit ............................................................................9, 35
U
UA................................................................................. 84, 89
Universal Synchronous Asynchronous Receiver Transmitter
(USART)
Asynchronous Mode
Setting Up Transmission................................... 113
Timing Diagram, Master Transmission............. 113
Transmitter........................................................ 112
Asynchronous Receiver
Setting Up Reception........................................ 115
Timing Diagram ................................................ 114
Asynchronous Receiver Mode
Block Diagram .................................................. 114
Section.............................................................. 114
Section...................................................................... 105
Synchronous Master Mode
Reception.......................................................... 118
Section.............................................................. 116
Setting Up Reception........................................ 118
Setting Up Transmission................................... 116
Timing Diagram, Reception .............................. 119
Timing Diagram, Transmission......................... 117
Transmission .................................................... 116
1997 Microchip Technology Inc.
DS30234D-page 325
PIC16C6X
Figure 4-15: PIE1 Register for PIC16C65/65A/R65/67
(Address 8Ch) ............................................ 40
LIST OF EQUATION AND EXAMPLES
Figure 4-16: PIR1 Register for PIC16C62/62A/R62
(Address 0Ch) ............................................ 41
Figure 4-17: PIR1 Register for PIC16C63/R63/66
Address 0Ch) ............................................. 42
Figure 4-18: PIR1 Register for PIC16C64/64A/R64
(Address 0Ch) ............................................ 43
Figure 4-19: PIR1 Register for PIC16C65/65A/R65/67
(Address 0Ch) ............................................ 44
Example 3-1: Instruction Pipeline Flow............................. 18
Example 4-1: Call of a Subroutine in Page 1
from Page 0 ................................................ 49
Example 4-2: Indirect Addressing..................................... 49
Example 5-1: Initializing PORTA....................................... 51
Example 5-2: Initializing PORTB....................................... 53
Example 5-3: Initializing PORTC ...................................... 55
Example 5-4: Read-Modify-Write Instructions on an
I/O Port ....................................................... 60
Example 7-1: Changing Prescaler (Timer0→WDT).......... 69
Example 7-2: Changing Prescaler (WDT→Timer0).......... 69
Example 8-1: Reading a 16-bit
Figure 4-20: PIE2 Register (Address 8Dh)..................... 45
Figure 4-21: PIR2 Register (Address 0Dh)..................... 46
Figure 4-22:
PCON Register for PIC16C62/64/65
(Address 8Eh) ............................................ 47
Figure 4-23: PCON Register for PIC16C62A/R62/63/
R63/64A/R64/65A/R65/66/67
Free-running Timer..................................... 73
Example 10-1: Changing Between
(Address 8Eh) ............................................ 47
Figure 4-24: Loading of PC in Different Situations ......... 48
Figure 4-25: Direct/Indirect Addressing .......................... 49
Capture Prescalers..................................... 79
Example 10-2: PWM Period and Duty
Cycle Calculation........................................ 81
Example 11-1: Loading the SSPBUF
Figure 5-1:
Block Diagram of the
RA3:RA0 Pins and the RA5 Pin ................. 51
Block Diagram of the RA4/T0CKI Pin......... 51
Block Diagram of the
RB7:RB4 Pins for PIC16C61/62/64/65....... 53
Block Diagram of the
RB7:RB4 Pins for PIC16C62A/63/R63/
64A/65A/R65/66/67.................................... 54
Block Diagram of the
(SSPSR) Register....................................... 86
Example 11-2: Loading the SSPBUF
(SSPSR) Register (PIC16C66/67).............. 91
Example 12-1: Calculating Baud Rate Error..................... 107
Example 13-1: Saving Status and W
Figure 5-2:
Figure 5-3:
Figure 5-4:
Figure 5-5:
Registers in RAM...................................... 139
Example 13-2: Saving Status, W, and
PCLATH Registers in RAM
RB3:RB0 Pins ............................................ 54
PORTC Block Diagram .............................. 55
PORTD Block Diagram
(All other PIC16C6X devices)................... 139
Figure 5-6:
Figure 5-7:
(In I/O Port Mode)....................................... 57
PORTE Block Diagram
(In I/O Port Mode)...................................... 58
TRISE Register (Address 89h)................... 58
LIST OF FIGURES
Figure 5-8:
Figure 5-9:
Figure 3-1:
Figure 3-2:
PIC16C61 Block Diagram........................... 10
PIC16C62/62A/R62/64/64A/R64
Block Diagram ............................................ 11
PIC16C63/R63/65/65A/R65
Figure 5-10: Successive I/O Operation........................... 60
Figure 5-11: PORTD and PORTE as a Parallel
Figure 3-3:
Block Diagram ............................................ 12
PIC16C66/67 Block Diagram...................... 13
Clock/Instruction Cycle ............................... 18
PIC16C61 Program Memory Map
and Stack.................................................... 19
PIC16C62/62A/R62/64/64A/
R64 Program Memory Map and Stack ....... 19
PIC16C63/R63/65/65A/R65 Program
Memory Map and Stack.............................. 19
PIC16C66/67 Program Memory
Map and Stack............................................ 20
PIC16C61 Register File Map...................... 20
PIC16C62/62A/R62/64/64A/
Slave Port................................................... 61
Figure 5-12: Parallel Slave Port Write Waveforms ......... 62
Figure 5-13: Parallel Slave Port Read Waveforms......... 62
Figure 3-4:
Figure 3-5:
Figure 4-1:
Figure 7-1:
Figure 7-2:
Timer0 Block Diagram................................ 65
Timer0 Timing: Internal Clock/No
Prescaler .................................................... 65
Timer0 Timing: Internal
Clock/Prescale 1:2 ..................................... 66
TMR0 Interrupt Timing ............................... 66
Timer0 Timing With External Clock............ 67
Block Diagram of the Timer0/WDT
Prescaler .................................................... 68
T1CON: Timer1 Control Register
Figure 4-2:
Figure 4-3:
Figure 4-4:
Figure 7-3:
Figure 7-4:
Figure 7-5:
Figure 7-6:
Figure 4-5:
Figure 4-6:
Figure 8-1:
R64 Register File Map................................ 21
PIC16C63/R63/65/65A/R65
Register File Map........................................ 21
PIC16C66/67 Data Memory Map................ 22
STATUS Register
(Address 10h)............................................. 71
Timer1 Block Diagram................................ 72
Timer2 Block Diagram................................ 75
T2CON: Timer2 Control Register
Figure 4-7:
Figure 8-2:
Figure 9-1:
Figure 9-2:
Figure 4-8:
Figure 4-9:
(Address 12h)............................................. 75
(Address 03h, 83h, 103h, 183h) ................. 35
Figure 10-1: CCP1CON Register (Address 17h) /
CCP2CON Register (Address 1Dh) ........... 78
Figure 10-2: Capture Mode Operation
Block Diagram............................................ 78
Figure 10-3: Compare Mode Operation
Figure 4-10: OPTION Register
(Address 81h, 181h) ................................... 36
Figure 4-11: INTCON Register
(Address 0Bh, 8Bh, 10Bh 18Bh)................. 37
Figure 4-12: PIE1 Register for PIC16C62/62A/R62
(Address 8Ch)............................................. 38
Figure 4-13: PIE1 Register for PIC16C63/R63/66
(Address 8Ch)............................................. 39
Figure 4-14: PIE1 Register for PIC16C64/64A/R64
(Address 8Ch)............................................. 39
Block Diagram............................................ 79
Figure 10-4: Simplified PWM Block Diagram.................. 80
Figure 10-5: PWM Output............................................... 80
Figure 11-1: SSPSTAT: Sync Serial Port Status
Register (Address 94h) .............................. 84
DS30234D-page 326
1997 Microchip Technology Inc.
PIC16C6X
Figure 11-2: SSPCON: Sync Serial Port
Control Register (Address 14h) .................. 85
Figure 13-2: Configuration Word for
PIC16C62/64/65........................................124
Figure 13-3: Configuration Word for
PIC16C62A/R62/63/R63/64A/R64/
65A/R65/66/67 ..........................................124
Figure 13-4: Crystal/Ceramic Resonator Operation
(HS, XT or LP OSC Configuration)............125
Figure 13-5: External Clock Input Operation
(HS, XT or LP OSC Configuration)............125
Figure 13-6: External Parallel Resonant
Crystal Oscillator Circuit............................127
Figure 13-7: External Series Resonant
Crystal Oscillator Circuit............................127
Figure 13-8: RC Oscillator Mode ...................................127
Figure 13-9: Simplified Block Diagram of
Figure 11-3: SSP Block Diagram (SPI Mode)................. 86
Figure 11-4: SPI Master/Slave Connection..................... 87
Figure 11-5: SPI Mode Timing, Master Mode or
Slave Mode w/o SS Control........................ 88
Figure 11-6: SPI Mode Timing, Slave Mode with
SS Control .................................................. 88
Figure 11-7: SSPSTAT: Sync Serial Port Status
Register (Address 94h)(PIC16C66/67)....... 89
Figure 11-8: SSPCON: Sync Serial Port Control
Register (Address 14h)(PIC16C66/67)....... 90
Figure 11-9: SSP Block Diagram (SPI Mode)
(PIC16C66/67)............................................ 91
Figure 11-10: SPI Master/Slave Connection
(PIC16C66/67)............................................ 92
Figure 11-11: SPI Mode Timing, Master Mode
(PIC16C66/67)............................................ 93
Figure 11-12: SPI Mode Timing (Slave Mode With
CKE = 0) (PIC16C66/67)............................ 93
Figure 11-13: SPI Mode Timing (Slave Mode With
CKE = 1) (PIC16C66/67)............................ 94
Figure 11-14: Start and Stop Conditions........................... 95
Figure 11-15: 7-bit Address Format .................................. 96
On-chip Reset Circuit ................................128
Figure 13-10: Brown-out Situations .................................129
Figure 13-11: Time-out Sequence on Power-up
(MCLR not Tied to VDD): Case 1...............134
Figure 13-12: Time-out Sequence on Power-up
(MCLR Not Tied To VDD): Case 2.............134
Figure 13-13: Time-out Sequence on Power-up
(MCLR Tied to VDD) ..................................134
Figure 13-14: External Power-on Reset Circuit
(For Slow VDD Power-up)..........................135
Figure 13-15: External Brown-out
2
Figure 11-16: I C 10-bit Address Format.......................... 96
Figure 11-17: Slave-receiver Acknowledge ...................... 96
Figure 11-18: Data Transfer Wait State ............................ 96
Figure 11-19: Master-transmitter Sequence ..................... 97
Figure 11-20: Master-receiver Sequence.......................... 97
Figure 11-21: Combined Format....................................... 97
Figure 11-22: Multi-master Arbitration
Protection Circuit 1....................................135
Figure 13-16: External Brown-out
Protection Circuit 2....................................135
Figure 13-17: Interrupt Logic for PIC16C61.....................137
Figure 13-18: Interrupt Logic for PIC16C6X ....................137
Figure 13-19: INT Pin Interrupt Timing ............................138
Figure 13-20: Watchdog Timer Block Diagram................140
Figure 13-21: Summary of Watchdog
Timer Registers.........................................140
Figure 13-22: Wake-up from Sleep
Through Interrupt.......................................142
Figure 13-23: Typical In-circuit Serial
Programming Connection..........................142
Figure 14-1: General Format for Instructions.................143
Figure 16-1: Load Conditions for Device Timing
Specifications ............................................168
Figure 16-2: External Clock Timing ...............................169
Figure 16-3: CLKOUT and I/O Timing ...........................170
Figure 16-4: Reset, Watchdog Timer, Oscillator
Start-up Timer and Power-up Timer
(Two Masters)............................................. 98
Figure 11-23: Clock Synchronization ................................ 98
2
Figure 11-24: SSP Block Diagram (I C Mode).................. 99
2
Figure 11-25: I C Waveforms for Reception
(7-bit Address) .......................................... 101
2
Figure 11-26: I C Waveforms for Transmission
(7-bit Address) .......................................... 102
2
Figure 11-27: Operation of the I C Module in
IDLE_MODE, RCV_MODE or
XMIT_MODE ............................................ 104
Figure 12-1: TXSTA: Transmit Status and
Control Register (Address 98h) ................ 105
Figure 12-2: RCSTA: Receive Status and
Control Register (Address 18h) ................ 106
Figure 12-3: RX Pin Sampling Scheme (BRGH = 0)
PIC16C63/R63/65/65A/R65) .................... 110
Timing........................................................171
Figure 16-5: Timer0 External Clock Timings .................172
Figure 17-1: Typical RC Oscillator
Figure 12-4: RX Pin Sampling Scheme (BRGH = 1)
(PIC16C63/R63/65/65A/R65) ................... 110
Figure 12-5: RX Pin Sampling Scheme (BRGH = 1)
(PIC16C63/R63/65/65A/R65) ................... 110
Frequency vs. Temperature .....................173
Figure 17-2: Typical RC Oscillator
Figure 12-6: RX Pin Sampling Scheme (BRGH = 0 or = 1)
(PIC16C66/67).......................................... 111
Frequency vs. VDD ....................................174
Figure 17-3: Typical RC Oscillator
Figure 12-7: USART Transmit Block Diagram .............. 112
Figure 12-8: Asynchronous Master Transmission......... 113
Figure 12-9: Asynchronous Master Transmission
(Back to Back) .......................................... 113
Figure 12-10: USART Receive Block Diagram ............... 114
Figure 12-11: Asynchronous Reception.......................... 114
Figure 12-12: Synchronous Transmission ...................... 117
Figure 12-13: Synchronous Transmission
through TXEN........................................... 117
Figure 12-14: Synchronous Reception
(Master Mode, SREN) .............................. 119
Figure 13-1: Configuration Word for PIC16C61............ 123
Frequency vs. VDD ....................................174
Figure 17-4: Typical RC Oscillator
Frequency vs. VDD ....................................174
Figure 17-5: Typical IPD vs. VDD Watchdog Timer
Disabled 25°C ...........................................174
Figure 17-6: Typical IPD vs. VDD Watchdog Timer
Enabled 25°C............................................175
Figure 17-7: Maximum IPD vs. VDD Watchdog
Disabled ....................................................175
Figure 17-8: Maximum IPD vs. VDD Watchdog
Enabled*....................................................176
Figure 17-9: VTH (Input Threshold Voltage) of
I/O Pins vs. VDD ........................................176
1997 Microchip Technology Inc.
DS30234D-page 327
PIC16C6X
Figure 17-10: VIH, VIL of MCLR, T0CKI and OSC1
(in RC Mode) vs. VDD ............................... 177
Figure 17-11: VTH (Input Threshold Voltage) of
OSC1 Input (in XT, HS,
Figure 20-7: Parallel Slave Port Timing........................ 226
Figure 20-8: SPI Mode Timing...................................... 227
2
Figure 20-9: I C Bus Start/Stop Bits Timing ................. 228
2
Figure 20-10: I C Bus Data Timing................................. 229
and LP Modes) vs. VDD ............................ 177
Figure 17-12: Typical IDD vs. Frequency
Figure 20-11: USART Synchronous Transmission
(Master/Slave) Timing .............................. 230
Figure 20-12: USART Synchronous Receive
(Master/Slave) Timing .............................. 230
Figure 21-1: Load Conditions for Device Timing
Specifications ........................................... 236
Figure 21-2: External Clock Timing .............................. 237
Figure 21-3: CLKOUT and I/O Timing .......................... 238
Figure 21-4: Reset, Watchdog Timer, Oscillator
Start-up Timer and Power-up Timer
Timing....................................................... 239
Figure 21-5: Brown-out Reset Timing........................... 239
Figure 21-6: Timer0 and Timer1 External Clock
Timings..................................................... 240
Figure 21-7: Capture/Compare/PWM Timings
(CCP1 and CCP2)................................... 241
Figure 21-8: Parallel Slave Port Timing
(External Clock, 25°C) .............................. 178
Figure 17-13: Maximum IDD vs. Frequency
(External Clock, -40° to +85°C) ................ 178
Figure 17-14: Maximum IDD vs. Frequency
(External Clock, -55° to +125°C) .............. 179
Figure 17-15: WDT Timer Time-out Period vs. VDD........ 179
Figure 17-16: Transconductance (gm) of HS
Oscillator vs. VDD...................................... 179
Figure 17-17: Transconductance (gm) of LP
Oscillator vs. VDD...................................... 180
Figure 17-18: Transconductance (gm) of XT
Oscillator vs. VDD...................................... 180
Figure 17-19: IOH vs. VOH, VDD = 3V .............................. 180
Figure 17-20: IOH vs. VOH, VDD = 5V .............................. 180
Figure 17-21: IOL vs. VOL, VDD = 3V............................... 181
Figure 17-22: IOL vs. VOL, VDD = 5V............................... 181
Figure 18-1: Load Conditions for Device
Timing Specifications................................ 188
Figure 18-2: External Clock Timing............................... 189
Figure 18-3: CLKOUT and I/O Timing........................... 190
Figure 18-4: Reset, Watchdog Timer,
Oscillator Start-up Timer and
Power-up Timer Timing ............................ 191
Figure 18-5: Timer0 and Timer1 External
(PIC16C65A)............................................ 242
Figure 21-9: SPI Mode Timing...................................... 243
2
Figure 21-10: I C Bus Start/Stop Bits Timing ................. 244
2
Figure 21-11: I C Bus Data Timing................................. 245
Figure 21-12: USART Synchronous Transmission
(Master/Slave) Timing .............................. 246
Figure 21-13: USART Synchronous Receive
(Master/Slave) Timing .............................. 246
Figure 22-1: Load Conditions for Device Timing
Specifications ........................................... 252
Figure 22-2: External Clock Timing .............................. 253
Figure 22-3: CLKOUT and I/O Timing .......................... 254
Figure 22-4: Reset, Watchdog Timer, Oscillator
Start-up Timer and Power-up Timer
Timing....................................................... 255
Figure 22-5: Brown-out Reset Timing........................... 255
Figure 22-6: Timer0 and Timer1 External Clock
Timings..................................................... 256
Figure 22-7: Capture/Compare/PWM Timings
(CCP1 and CCP2).................................... 257
Figure 22-8: Parallel Slave Port Timing
Clock Timings ........................................... 192
Figure 18-6: Capture/Compare/PWM Timings
(CCP1)...................................................... 193
Figure 18-7: Parallel Slave Port Timing
(PIC16C64)............................................... 194
Figure 18-8: SPI Mode Timing ...................................... 195
2
Figure 18-9: I C Bus Start/Stop Bits Timing.................. 196
2
Figure 18-10: I C Bus Data Timing................................. 197
Figure 19-1: Load Conditions for Device
Timing Specifications................................ 204
Figure 19-2: External Clock Timing............................... 205
Figure 19-3: CLKOUT and I/O Timing........................... 206
Figure 19-4: Reset, Watchdog Timer,
(PIC16CR65)............................................ 258
Figure 22-9: SPI Mode Timing...................................... 259
Oscillator Start-up Timer and
2
Power-up Timer Timing ............................ 207
Figure 19-5: Brown-out Reset Timing ........................... 207
Figure 19-6: Timer0 and Timer1 External
Clock Timings ........................................... 208
Figure 19-7: Capture/Compare/PWM Timings
(CCP1)...................................................... 209
Figure 19-8: Parallel Slave Port Timing
Figure 22-10: I C Bus Start/Stop Bits Timing ................. 260
2
Figure 22-11: I C Bus Data Timing................................. 261
Figure 22-12: USART Synchronous Transmission
(Master/Slave) Timing .............................. 262
Figure 22-13: USART Synchronous Receive
(Master/Slave) Timing .............................. 262
Figure 23-1: Load Conditions for Device Timing
Specifications ........................................... 268
Figure 23-2: External Clock Timing .............................. 269
Figure 23-3: CLKOUT and I/O Timing .......................... 270
Figure 23-4: Reset, Watchdog Timer, Oscillator
Start-up Timer and Power-up Timer
(PIC16C64A/R64)..................................... 210
Figure 19-9: SPI Mode Timing ...................................... 211
2
Figure 19-10: I C Bus Start/Stop Bits Timing.................. 212
2
Figure 19-11: I C Bus Data Timing................................. 213
Figure 20-1: Load Conditions for Device Timing
Specifications............................................ 220
Figure 20-2: External Clock Timing............................... 221
Figure 20-3: CLKOUT and I/O Timing........................... 222
Figure 20-4: Reset, Watchdog Timer, Oscillator
Start-up Timer and Power-up Timer
Timing....................................................... 223
Figure 20-5: Timer0 and Timer1 External Clock
Timings ..................................................... 224
Figure 20-6: Capture/Compare/PWM Timings
(CCP1 and CCP2) .................................... 225
Timing....................................................... 271
Figure 23-5: Brown-out Reset Timing........................... 271
Figure 23-6: Timer0 and Timer1 External Clock
Timings..................................................... 272
Figure 23-7: Capture/Compare/PWM Timings
(CCP1 and CCP2).................................... 273
Figure 23-8: Parallel Slave Port Timing (PIC16C67).... 274
Figure 23-9: SPI Master Mode Timing (CKE = 0)......... 275
Figure 23-10: SPI Master Mode Timing (CKE = 1)......... 275
Figure 23-11: SPI Slave Mode Timing (CKE = 0)........... 276
DS30234D-page 328
1997 Microchip Technology Inc.
PIC16C6X
Figure 23-12: SPI Slave Mode Timing (CKE = 1) ........... 276
Figure 24-29: Typical IDD vs. Frequency
(HS Mode, 25°C).......................................290
Figure 24-30: Maximum IDD vs. Frequency
2
Figure 23-13: I C Bus Start/Stop Bits Timing.................. 278
2
Figure 23-14: I C Bus Data Timing................................. 279
Figure 23-15: USART Synchronous Transmission
(Master/Slave) Timing............................... 280
Figure 23-16: USART Synchronous Receive
(Master/Slave) Timing............................... 280
Figure 24-1: Typical IPD vs. VDD
(HS Mode, -40°C to 85°C).........................290
(WDT Disabled, RC Mode)....................... 281
Figure 24-2: Maximum IPD vs. VDD
(WDT Disabled, RC Mode)....................... 281
Figure 24-3: Typical IPD vs. VDD @ 25°C
(WDT Enabled, RC Mode)........................ 282
Figure 24-4: Maximum IPD vs. VDD
(WDT Enabled, RC Mode)........................ 282
Figure 24-5: Typical RC Oscillator
Frequency vs. VDD.................................... 282
Figure 24-6: Typical RC Oscillator
Frequency vs. VDD.................................... 282
Figure 24-7: Typical RC Oscillator
Frequency vs. VDD.................................... 282
Figure 24-8: Typical IPD vs. VDD Brown-out
Detect Enabled (RC Mode)....................... 283
Figure 24-9: Maximum IPD vs. VDD Brown-out
Detect Enabled
(85°C to -40°C, RC Mode)........................ 283
Figure 24-10: Typical IPD vs. Timer1 Enabled
(32 kHz, RC0/RC1 = 33 pF/33 pF,
RC Mode) ................................................ 283
Figure 24-11: Maximum IPD vs. Timer1 Enabled
(32 kHz, RC0/RC1 = 33 pF/33 pF,
85°C to -40°C, RC Mode)......................... 283
Figure 24-12: Typical IDD vs. Frequency
(RC Mode @ 22 pF, 25°C) ....................... 284
Figure 24-13: Maximum IDD vs. Frequency
(RC Mode @ 22 pF, -40°C to 85°C)......... 284
Figure 24-14: Typical IDD vs. Frequency
(RC Mode @ 100 pF, 25°C) ..................... 285
Figure 24-15: Maximum IDD vs. Frequency
(RC Mode @ 100 pF, -40°C to 85°C)....... 285
Figure 24-16: Typical IDD vs. Frequency
(RC Mode @ 300 pF, 25°C) ..................... 286
Figure 24-17: Maximum IDD vs. Frequency
(RC Mode @ 300 pF, -40°C to 85°C)....... 286
Figure 24-18: Typical IDD vs. Capacitance @ 500 kHz
(RC Mode) ................................................ 287
Figure 24-19: Transconductance(gm) of HS
Oscillator vs. VDD...................................... 287
Figure 24-20: Transconductance(gm) of LP
Oscillator vs. VDD...................................... 287
Figure 24-21: Transconductance(gm) of XT
Oscillator vs. VDD...................................... 287
Figure 24-22: Typical XTAL Startup Time vs. VDD
(LP Mode, 25°C)....................................... 288
Figure 24-23: Typical XTAL Startup Time vs. VDD
(HS Mode, 25°C) ...................................... 288
Figure 24-24: Typical XTAL Startup Time vs. VDD
(XT Mode, 25°C)....................................... 288
Figure 24-25: Typical Idd vs. Frequency
(LP Mode, 25°C)....................................... 289
Figure 24-26: Maximum IDD vs. Frequency
(LP Mode, 85°C to -40°C)......................... 289
Figure 24-27: Typical IDD vs. Frequency
(XT Mode, 25°C)....................................... 289
Figure 24-28: Maximum IDD vs. Frequency
(XT Mode, -40°C to 85°C) ........................ 289
1997 Microchip Technology Inc.
DS30234D-page 329
PIC16C6X
Table 12-2:
Registers Associated with Baud
LIST OF TABLES
Rate Generator......................................... 107
Baud Rates for Synchronous Mode ......... 108
Baud Rates for Asynchronous Mode
(BRGH = 0)............................................... 108
Baud Rates for Asynchronous Mode
(BRGH = 1)............................................... 109
Registers Associated with
Asynchronous Transmission .................... 113
Registers Associated with
Asynchronous Reception ......................... 115
Registers Associated with
Table 12-3:
Table 12-4:
Table 1-1:
Table 3-1:
Table 3-2:
PIC16C6X Family of Devices ....................... 6
PIC16C61 Pinout Description..................... 14
PIC16C62/62A/R62/63/R63/66
Table 12-5:
Table 12-6:
Table 12-7:
Table 12-8:
Table 12-9:
Pinout Description....................................... 15
PIC16C64/64A/R64/65/65A/R65/67
Pinout Description....................................... 16
Special Function Registers for the
PIC16C61 ................................................... 23
Special Function Registers for the
PIC16C62/62A/R62 .................................... 24
Special Function Registers for the
PIC16C63/R63............................................ 26
Special Function Registers for the
PIC16C64/64A/R64 .................................... 28
Special Function Registers for the
PIC16C65/65A/R65 .................................... 30
Special Function Registers for the
Table 3-3:
Table 4-1:
Table 4-2:
Table 4-3:
Table 4-4:
Table 4-5:
Table 4-6:
Synchronous Master Transmission.......... 117
Registers Associated with
Synchronous Master Reception ............... 118
Table 12-10: Registers Associated with
Synchronous Slave Transmission............ 121
Table 12-11: Registers Associated with
Synchronous Slave Reception ................. 121
Table 13-1:
Table 13-2:
Ceramic Resonators PIC16C61............... 126
Ceramic Resonators
PIC16C62/62A/R62/63/R63/
PIC16C66/67 .............................................. 32
PORTA Functions....................................... 52
Registers/Bits Associated with
Table 5-1:
Table 5-2:
64/64A/R64/65/65A/R65/66/67 ................ 126
Capacitor Selection for Crystal
Oscillator for PIC16C61............................ 126
Capacitor Selection for Crystal
Oscillator for PIC16C62/62A/R62/63/R63/
64/64A/R64/65/65A/R65/66/67 ................ 126
Time-out in Various Situations,
PIC16C61/62/64/65.................................. 130
Time-out in Various Situations,
PORTA ....................................................... 52
PORTB Functions....................................... 54
Summary of Registers Associated with
PORTB ....................................................... 54
PORTC Functions for PIC16C62/64........... 55
PORTC Functions for
Table 13-3:
Table 13-4:
Table 5-3:
Table 5-4:
Table 5-5:
Table 5-6:
Table 13-5:
Table 13-6:
PIC16C62A/R62/64A/R64 .......................... 56
PORTC Functions for
Table 5-7:
Table 5-8:
PIC16C63/R63/65/65A/R65/66/67.............. 56
Summary of Registers Associated with
PORTC ....................................................... 56
PORTD Functions....................................... 57
Summary of Registers Associated with
PORTD ....................................................... 57
PORTE Functions....................................... 59
Summary of Registers Associated with
PORTE ....................................................... 59
Registers Associated with
PIC16C62A/R62/63/R63/
64A/R64/65A/R65/66/67 .......................... 130
Status Bits and Their Significance,
PIC16C61................................................. 130
Status bits and Their Significance,
PIC16C62/64/65....................................... 130
Status Bits and Their Significance for
PIC16C62A/R62/63/R63/
Table 13-7:
Table 13-8:
Table 13-9:
Table 5-9:
Table 5-10:
Table 5-11:
Table 5-12:
64A/R64/65A/R65/66/67 .......................... 131
Table 5-13:
Table 13-10: Reset Condition for Special
Registers on PIC16C61/62/64/65............. 131
Table 13-11: Reset Condition for Special
Registers on
Parallel Slave Port ...................................... 62
Registers Associated with Timer0 .............. 69
Capacitor Selection for the
Timer1 Oscillator......................................... 73
Registers Associated with
Timer1 as a Timer/Counter......................... 74
Registers Associated with
Timer2 as a Timer/Counter......................... 76
CCP Mode - Timer Resource ..................... 77
Interaction of Two CCP Modules................ 77
Example PWM Frequencies
and Resolutions at 20 MHz......................... 81
Registers Associated with Timer1,
Capture and Compare ................................ 81
Registers Associated with PWM
and Timer2.................................................. 82
Registers Associated with SPI
Operation.................................................... 88
Registers Associated with SPI
Table 7-1:
Table 8-1:
PIC16C62A/R62/63/R63/
Table 8-2:
Table 9-1:
64A/R64/65A/R65/66/67 .......................... 131
Table 13-12: Initialization Conditions for
all Registers.............................................. 132
Table 14-1:
Table 14-2:
Table 15-1:
Table 16-1:
Opcode Field Descriptions ....................... 143
PIC16CXX Instruction Set........................ 144
Development Tools from Microchip.......... 162
Cross Reference of Device
Table 10-1:
Table 10-2:
Table 10-3:
Specs for Oscillator Configurations
and Frequencies of Operation
Table 10-4:
Table 10-5:
Table 11-1:
Table 11-2:
(Commercial Devices).............................. 163
External Clock Timing
Requirements........................................... 169
CLKOUT and I/O Timing
Requirements........................................... 170
Reset, Watchdog Timer,
Table 16-2:
Table 16-3:
Table 16-4:
Operation (PIC16C66/67)........................... 94
2
Oscillator Start-up Timer and
Table 11-3:
Table 11-4:
I C Bus Terminology................................... 95
Power-up Timer Requirements ................ 171
Timer0 External Clock Requirements....... 172
RC Oscillator Frequencies ....................... 173
Input Capacitance*................................... 181
Data Transfer Received Byte
Table 16-5:
Table 17-1:
Table 17-2:
Actions...................................................... 100
2
Table 11-5:
Table 12-1:
Registers Associated with I C
Operation.................................................. 103
Baud Rate Formula................................... 107
DS30234D-page 330
1997 Microchip Technology Inc.
PIC16C6X
Table 18-1:
Cross Reference of Device Specs
for Oscillator Configurations and
Frequencies of Operation
Table 20-12: USART Synchronous Receive
Requirements............................................230
Cross Reference of Device
Table 21-1:
(Commercial Devices) .............................. 183
External Clock Timing
Requirements ........................................... 189
CLKOUT and I/O Timing
Requirements ........................................... 190
Reset, Watchdog Timer,
Oscillator Start-up Timer and
Power-up Timer Requirements................. 191
Timer0 and Timer1 External
Clock Requirements ................................. 192
Capture/Compare/PWM
Specs for Oscillator Configurations
and Frequencies of Operation
(Commercial Devices)...............................231
External Clock Timing
Requirements............................................237
CLKOUT and I/O Timing
Requirements............................................238
Reset, Watchdog Timer, Oscillator
Start-up Timer, Power-up Timer, and
Brown-out Reset Requirements ................239
Timer0 and Timer1 External
Clock Requirements..................................240
Capture/Compare/PWM
Requirements (CCP1 and CCP2) .............241
Parallel Slave Port Requirements
Table 18-2:
Table 18-3:
Table 18-4:
Table 21-2:
Table 21-3:
Table 21-4:
Table 18-5:
Table 18-6:
Table 18-7:
Table 21-5:
Table 21-6:
Table 21-7:
Requirements (CCP1) .............................. 193
Parallel Slave Port Requirements
(PIC16C64)............................................... 194
SPI Mode Requirements........................... 195
Table 18-8:
Table 18-9:
2
I C Bus Start/Stop Bits
(PIC16C65A).............................................242
SPI Mode Requirements ...........................243
Requirements ........................................... 196
Table 21-8:
Table 21-9:
2
2
Table 18-10: I C Bus Data Requirements ..................... 197
I C Bus Start/Stop Bits
Table 19-1:
Cross Reference of Device Specs
for Oscillator Configurations and
Frequencies of Operation
Requirements............................................244
Table 21-10: I C Bus Data Requirements......................245
Table 21-11: USART Synchronous
2
(Commercial Devices) .............................. 199
External Clock Timing
Requirements ........................................... 205
CLKOUT and I/O Timing
Requirements ........................................... 206
Reset, Watchdog Timer,
Transmission Requirements......................246
Table 21-12: USART Synchronous Receive
Requirements...........................................246
Table 19-2:
Table 19-3:
Table 19-4:
Table 22-1:
Cross Reference of Device Specs
for Oscillator Configurations and
Frequencies of Operation
Oscillator Start-up Timer,
Power-up Timer, and Brown-out
Reset Requirements................................. 207
Timer0 and Timer1 External
Clock Requirements ................................. 208
Capture/Compare/PWM
(Commercial Devices)...............................247
External Clock Timing
Requirements............................................253
CLKOUT and I/O Timing
Requirements............................................254
Reset, Watchdog Timer,
Table 22-2:
Table 22-3:
Table 22-4:
Table 19-5:
Table 19-6:
Table 19-7:
Requirements (CCP1) .............................. 209
Parallel Slave Port Requirements
(PIC16C64A/R64)..................................... 210
SPI Mode Requirements........................... 211
Oscillator Start-up Timer,
Power-up Timer, and Brown-out
Reset Requirements..................................255
Timer0 and Timer1 External
Clock Requirements..................................256
Capture/Compare/PWM
Table 19-8:
Table 19-9:
Table 22-5:
Table 22-6:
Table 22-7:
2
I C Bus Start/Stop Bits
Requirements ........................................... 212
2
Table 19-10: I C Bus Data Requirements ..................... 213
Table 20-1:
Requirements (CCP1 and CCP2) .............257
Parallel Slave Port Requirements
(PIC16CR65).............................................258
SPI Mode Requirements ...........................259
Cross Reference of Device Specs
for Oscillator Configurations and
Frequencies of Operation
(Commercial Devices) .............................. 215
External Clock Timing
Requirements ........................................... 221
CLKOUT and I/O Timing
Requirements ........................................... 222
Reset, Watchdog Timer,
Oscillator Start-up Timer and
Table 22-8:
Table 22-9:
2
I C Bus Start/Stop Bits
Table 20-2:
Table 20-3:
Table 20-4:
Requirements............................................260
2
Table 22-10: I C Bus Data Requirements......................261
Table 22-11: USART Synchronous Transmission
Requirements............................................262
Table 22-12: USART Synchronous Receive
Requirements...........................................262
Power-up Timer Requirements................. 223
Timer0 and Timer1 External
Clock Requirements ................................. 224
Capture/Compare/PWM
Table 23-1:
Cross Reference of Device Specs
for Oscillator Configurations and
Frequencies of Operation
(Commercial Devices)...............................263
External Clock Timing
Requirements............................................269
CLKOUT and I/O Timing
Requirements............................................270
Reset, Watchdog Timer,
Table 20-5:
Table 20-6:
Requirements (CCP1 and CCP2)............. 225
Parallel Slave Port Requirements............. 226
SPI Mode Requirements........................... 227
Table 23-2:
Table 23-3:
Table 23-4:
Table 20-7:
Table 20-8:
Table 20-9:
2
I C Bus Start/Stop Bits
Requirements ........................................... 228
2
Table 20-10: i C Bus Data Requirements...................... 229
Table 20-11: USART Synchronous Transmission
Requirements ........................................... 230
Oscillator Start-up Timer,
Power-up Timer, and Brown-out
Reset Requirements..................................271
1997 Microchip Technology Inc.
DS30234D-page 331
PIC16C6X
Table 23-5:
Table 23-6:
Table 23-7:
Timer0 and Timer1 External
Clock Requirements ................................. 272
Capture/Compare/PWM
Requirements (CCP1 and CCP2)............. 273
Parallel Slave Port Requirements
(PIC16C67)............................................... 274
SPI Mode Requirements........................... 277
I C Bus Start/Stop Bits
Table 23-8:
Table 23-9:
2
Requirements ........................................... 278
2
Table 23-10: I C Bus Data Requirements ..................... 279
Table 23-11: USART Synchronous Transmission
Requirements ........................................... 280
Table 23-12: USART Synchronous Receive
Requirements ........................................... 280
Table 24-1:
Table 24-2:
RC Oscillator Frequencies........................ 287
Capacitor Selection for Crystal
Oscillators................................................. 288
Pin Compatible Devices............................ 315
Table E-1:
DS30234D-page 332
1997 Microchip Technology Inc.
PIC16C6X
The procedure to connect will vary slightly from country
to country. Please check with your local CompuServe
agent for details if you have a problem. CompuServe
service allow multiple users various baud rates
depending on the local point of access.
ON-LINE SUPPORT
Microchip provides two methods of on-line support.
These are the Microchip BBS and the Microchip World
Wide Web (WWW) site.
Use Microchip's Bulletin Board Service (BBS) to get
current information and help about Microchip products.
Microchip provides the BBS communication channel
for you to use in extending your technical staff with
microcontroller and memory experts.
The following connect procedure applies in most loca-
tions.
1. Set your modem to 8-bit, No parity, and One stop
(8N1). This is not the normal CompuServe setting
which is 7E1.
To provide you with the most responsive service possible,
the Microchip systems team monitors the BBS, posts
the latest component data and software tool updates,
provides technical help and embedded systems
insights, and discusses how Microchip products pro-
vide project solutions.
2. Dial your local CompuServe access number.
3. Depress the <Enter> key and a garbage string will
appear because CompuServe is expecting a 7E1
setting.
4. Type +, depress the <Enter> key and “Host Name:”
will appear.
The web site, like the BBS, is used by Microchip as a
means to make files and information easily available to
customers. To view the site, the user must have access
to the Internet and a web browser, such as Netscape or
Microsoft Explorer. Files are also available for FTP
download from our FTP site.
5. Type MCHIPBBS, depress the <Enter> key and you
will be connected to the Microchip BBS.
In the United States, to find the CompuServe phone
number closest to you, set your modem to 7E1 and dial
(800) 848-4480 for 300-2400 baud or (800) 331-7166
for 9600-14400 baud connection. After the system
responds with “Host Name:”, type NETWORK, depress
the <Enter> key and follow CompuServe's directions.
ConnectingtotheMicrochipInternetWebSite
The Microchip web site is available by using your
favorite Internet browser to attach to:
www.microchip.com
For voice information (or calling from overseas), you
may call (614) 723-1550 for your local CompuServe
number.
The file transfer site is available by using an FTP ser-
vice to connect to:
Microchip regularly uses the Microchip BBS to distribute
technical information, application notes, source code,
errata sheets, bug reports, and interim patches for
Microchip systems software products. For each SIG, a
moderator monitors, scans, and approves or disap-
proves files submitted to the SIG. No executable files
are accepted from the user community in general to
limit the spread of computer viruses.
ftp://ftp.futureone.com/pub/microchip
The web site and file transfer site provide a variety of
services. Users may download files for the latest
Development Tools, Data Sheets, Application Notes,
User's Guides, Articles and Sample Programs. A vari-
ety of Microchip specific business information is also
available, including listings of Microchip sales offices,
distributors and factory representatives. Other data
available for consideration is:
Systems Information and Upgrade Hot Line
The Systems Information and Upgrade Line provides
system users a listing of the latest versions of all of
Microchip's development systems software products.
Plus, this line provides information on how customers
can receive any currently available upgrade kits.The
Hot Line Numbers are:
• Latest Microchip Press Releases
• Technical Support Section with Frequently Asked
Questions
• Design Tips
• Device Errata
• Job Postings
• Microchip Consultant Program Member Listing
• Links to other useful web sites related to
Microchip Products
1-800-755-2345 for U.S. and most of Canada, and
1-602-786-7302 for the rest of the world.
970301
Trademarks: The Microchip name, logo, PIC, PICSTART,
PICMASTER and PRO MATE are registered trademarks
of Microchip Technology Incorporated in the U.S.A. and
other countries. FlexROM, MPLAB and fuzzyLAB, are
trademarks and SQTP is a service mark of Microchip in
the U.S.A.
Connecting to the Microchip BBS
Connect worldwide to the Microchip BBS using either
the Internet or the CompuServe communications net-
work.
Internet:
fuzzyTECH is a registered trademark of Inform Software
Corporation. IBM, IBM PC-AT are registered trademarks
of International Business Machines Corp. Pentium is a
trademark of Intel Corporation. Windows is a trademark
and MS-DOS, Microsoft Windows are registered trade-
marks of Microsoft Corporation. CompuServe is a regis-
tered trademark of CompuServe Incorporated.
You can telnet or ftp to the Microchip BBS at the
address: mchipbbs.microchip.com
CompuServe Communications Network:
When using the BBS via the Compuserve Network,
in most cases, a local call is your only expense. The
Microchip BBS connection does not use CompuServe
membership services, therefore you do not need
CompuServe membership to join Microchip's BBS.
There is no charge for connecting to the Microchip BBS.
All other trademarks mentioned herein are the property of
their respective companies.
1997 Microchip Technology Inc.
DS30234D-page 333
PIC16C6X
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip prod-
uct. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (602) 786-7578.
Please list the following information, and use this outline to provide us with your comments about this Data Sheet.
To:
Technical Publications Manager
Reader Response
Total Pages Sent
RE:
From:
Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
Literature Number:
DS30234D
Device:
PIC16C6X
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this data sheet easy to follow? If not, why?
4. What additions to the data sheet do you think would enhance the structure and subject?
5. What deletions from the data sheet could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
8. How would you improve our software, systems, and silicon products?
DS30234D-page 334
1997 Microchip Technology Inc.
PIC16C6X
PIC16C6X Product Identification System
To order or to obtain information, e.g., on pricing or delivery, please use the listed part numbers, and refer to the factory or the listed
sales offices.
PART NO. -XX X /XX XXX
Pattern:
3-Digit Pattern Code for QTP (blank otherwise)
Package:
L
SP
P
SO
PQ
TQ
JW*
SS
=
=
=
=
=
=
=
=
PLCC
Skinny DIP
PDIP
SOIC (Gull Wing, 300 mil body)
MQFP (Metric PQFP)
TQFP
Windowed CERDIP
Shrink SOIC (Gull Wing, 300 mil body)
Temperature
Range:
-
I
E
=
=
=
0˚C to +70˚C (T for tape/reel)
– 40˚C to +85˚C (S for tape/reel)
– 40˚C to +125˚C
Frequency
Range:
04
04
10
20
=
=
=
=
200 kHz (PIC16C6X-04)
4 MHz
10 MHz
20 MHz
Device:
PIC16C6X :VDD range 4.0V to 6.0V
PIC16C6XT :VDD range 4.0V to 6.0V (Tape and Reel)
PIC16LC6X :VDD range 2.5V to 6.0V
PIC16LC6XT :VDD range 2.5V to 6.0V (Tape and Reel)
PIC16CR6X :VDD range 4.0V to 6.0V
PIC16CR6XT:VDD range 4.0V to 6.0V (Tape and Reel)
PIC16LCR6X :VDD range 2.5V to 6.0V
PIC16LCR6XT:VDD range 2.5V to 6.0V
Examples:
a)PIC16C62A - 04/P 301 = Commercial temp., PDIP package, 4 MHz, normal VDD limits, QTP pattern #301
b)PIC16LC65A - 04I/PQ
c)PIC16C67 - 10E/P
=
=
Industrial temp., MQFP package, 4 MHz, extended VDD limits
Extended temp., PDIP package, 10 MHz, normal VDD limits
* JW Devices are UV erasable and can be programmed to any device configuration. JW Devices meet the electrical requirement of
each oscillator type (including LC devices).
Sales and Support
Products supported by a preliminary Data Sheet may possibly have an errata sheet describing minor operational differences and
recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
1. The Microchip Website at www.microchip.com
2. Your local Microchip sales office (see following page)
3. The Microchip Corporate Literature Center U.S. FAX: (602) 786-7277
4. The Microchip’s Bulletin Board, via your local CompuServe number (CompuServe membership NOT required).
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using.
For latest version information and upgrade kits for Microchip Development Tools, please call 1-800-755-2345 or 1-602-786-7302.
1997 Microchip Technology Inc.
DS30234D-page 335
WORLDWIDE SALES AND SERVICE
AMERICAS
AMERICAS (continued)
ASIA/PACIFIC (continued)
Corporate Office
Toronto
Singapore
Microchip Technology Inc.
Microchip Technology Inc.
Microchip Technology Singapore Pte Ltd.
200 Middle Road
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-786-7200 Fax: 480-786-7277
Technical Support: 480-786-7627
Web Address: http://www.microchip.com
5925 Airport Road, Suite 200
Mississauga, Ontario L4V 1W1, Canada
Tel: 905-405-6279 Fax: 905-405-6253
#07-02 Prime Centre
Singapore 188980
Tel: 65-334-8870 Fax: 65-334-8850
Taiwan, R.O.C
Microchip Technology Taiwan
10F-1C 207
Tung Hua North Road
Taipei, Taiwan, ROC
ASIA/PACIFIC
Hong Kong
Microchip Asia Pacific
Unit 2101, Tower 2
Atlanta
Microchip Technology Inc.
500 Sugar Mill Road, Suite 200B
Atlanta, GA 30350
Metroplaza
223 Hing Fong Road
Kwai Fong, N.T., Hong Kong
Tel: 852-2-401-1200 Fax: 852-2-401-3431
Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
Tel: 770-640-0034 Fax: 770-640-0307
Boston
EUROPE
Microchip Technology Inc.
5 Mount Royal Avenue
Marlborough, MA 01752
Tel: 508-480-9990 Fax: 508-480-8575
Beijing
United Kingdom
Microchip Technology, Beijing
Unit 915, 6 Chaoyangmen Bei Dajie
Dong Erhuan Road, Dongcheng District
New China Hong Kong Manhattan Building
Beijing 100027 PRC
Arizona Microchip Technology Ltd.
505 Eskdale Road
Winnersh Triangle
Wokingham
Berkshire, England RG41 5TU
Tel: 44 118 921 5858 Fax: 44-118 921-5835
Denmark
Microchip Technology Denmark ApS
Regus Business Centre
Lautrup hoj 1-3
Ballerup DK-2750 Denmark
Tel: 45 4420 9895 Fax: 45 4420 9910
Chicago
Microchip Technology Inc.
333 Pierce Road, Suite 180
Itasca, IL 60143
Tel: 86-10-85282100 Fax: 86-10-85282104
India
Tel: 630-285-0071 Fax: 630-285-0075
Dallas
Microchip Technology Inc.
4570 Westgrove Drive, Suite 160
Addison, TX 75248
Microchip Technology Inc.
India Liaison Office
No. 6, Legacy, Convent Road
Bangalore 560 025, India
Tel: 91-80-229-0061 Fax: 91-80-229-0062
Tel: 972-818-7423 Fax: 972-818-2924
Dayton
Microchip Technology Inc.
Two Prestige Place, Suite 150
Miamisburg, OH 45342
Tel: 937-291-1654 Fax: 937-291-9175
Detroit
Microchip Technology Inc.
Tri-Atria Office Building
32255 Northwestern Highway, Suite 190
Farmington Hills, MI 48334
Tel: 248-538-2250 Fax: 248-538-2260
Japan
France
Microchip Technology Intl. Inc.
Benex S-1 6F
Arizona Microchip Technology SARL
Parc d’Activite du Moulin de Massy
43 Rue du Saule Trapu
3-18-20, Shinyokohama
Kohoku-Ku, Yokohama-shi
Kanagawa 222-0033 Japan
Tel: 81-45-471- 6166 Fax: 81-45-471-6122
Batiment A - ler Etage
91300 Massy, France
Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Germany
Arizona Microchip Technology GmbH
Gustav-Heinemann-Ring 125
D-81739 München, Germany
Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
Korea
Microchip Technology Korea
168-1, Youngbo Bldg. 3 Floor
Samsung-Dong, Kangnam-Ku
Seoul, Korea
Tel: 82-2-554-7200 Fax: 82-2-558-5934
Shanghai
Microchip Technology
RM 406 Shanghai Golden Bridge Bldg.
2077 Yan’an Road West, Hong Qiao District
Shanghai, PRC 200335
Italy
Los Angeles
Arizona Microchip Technology SRL
Centro Direzionale Colleoni
Palazzo Taurus 1 V. Le Colleoni 1
20041 Agrate Brianza
Microchip Technology Inc.
18201 Von Karman, Suite 1090
Irvine, CA 92612
Tel: 949-263-1888 Fax: 949-263-1338
New York
Microchip Technology Inc.
150 Motor Parkway, Suite 202
Hauppauge, NY 11788
Tel: 631-273-5305 Fax: 631-273-5335
Milan, Italy
Tel: 39-039-65791-1 Fax: 39-039-6899883
Tel: 86-21-6275-5700 Fax: 86 21-6275-5060
11/15/99
San Jose
Microchip received QS-9000 quality system
certification for its worldwide headquarters,
design and wafer fabrication facilities in
Chandler and Tempe, Arizona in July 1999. The
Company’s quality system processes and
procedures are QS-9000 compliant for its
PICmicro® 8-bit MCUs, KEELOQ® code hopping
devices, Serial EEPROMs and microperipheral
products. In addition, Microchip’s quality
system for the design and manufacture of
development systems is ISO 9001 certified.
Microchip Technology Inc.
2107 North First Street, Suite 590
San Jose, CA 95131
Tel: 408-436-7950 Fax: 408-436-7955
All rights reserved. © 1999 Microchip Technology Incorporated. Printed in the USA. 11/99
Printed on recycled paper.
Information contained in this publication regarding device applications and the like is intended for suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed
by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products
as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip
logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies.
1999 Microchip Technology Inc.
相关型号:
PIC16C64A/JW
8-BIT, UVPROM, 20 MHz, RISC MICROCONTROLLER, CDIP40, 0.600 INCH, WINDOWED, CERAMIC, DIP-40
MICROCHIP
PIC16C64AS-20I/TQ
8-BIT, OTPROM, 20 MHz, RISC MICROCONTROLLER, PQFP44, 10 X 10 MM, PLASTIC, TQFP-44
MICROCHIP
PIC16C64AT-04/PQ
8-BIT, OTPROM, 4 MHz, RISC MICROCONTROLLER, PQFP44, 10 X 10 MM, PLASTIC, MQFP-44
MICROCHIP
PIC16C64AT-04/TQ
8-BIT, OTPROM, 4 MHz, RISC MICROCONTROLLER, PQFP44, 10 X 10 MM, PLASTIC, MS-026, TQFP-44
MICROCHIP
©2020 ICPDF网 联系我们和版权申明