PIC16CR54B-10I/SO [MICROCHIP]
8-BIT, MROM, 10 MHz, RISC MICROCONTROLLER, PDSO18, 0.300 INCH, PLASTIC, SOIC-18;型号: | PIC16CR54B-10I/SO |
厂家: | MICROCHIP |
描述: | 8-BIT, MROM, 10 MHz, RISC MICROCONTROLLER, PDSO18, 0.300 INCH, PLASTIC, SOIC-18 光电二极管 |
文件: | 总202页 (文件大小:1454K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ENHANCED PIC16C5X
EPROM/ROM-Based 8-Bit CMOS Microcontroller Series
Devices Included in this Data Sheet
• PIC16C54A
Pin Diagram
PDIP, SOIC, Windowed CERDIP
• PIC16CR54A
18
17
16
15
14
13
12
11
10
RA1
• 1
2
RA2
RA3
• PIC16CR54B
RA0
• PIC16CR56
OSC1/CLKIN
OSC2/CLKOUT
VDD
3
T0CKI
MCLR/VPP
VSS
4
• PIC16CR57A
5
• PIC16CR57B
RB7
6
RB0
RB6
• PIC16C58A
7
RB1
RB5
8
RB2
• PIC16CR58A
RB4
9
RB3
• PIC16CR58B
High-Performance RISC CPU
• Only 33 single word instructions to learn
PDIP, SOIC, CERDIP
• All instructions are single cycle (200 ns) except
for program branches which are two-cycle
T0CKI
• 1
28
27
26
25
24
23
22
21
20
19
18
17
16
15
MCLR
OSC1/CLKIN
OSC2/CLKOUT
RC7
VDD
2
N/C
3
• Operating speed: DC - 20 MHz clock input
DC - 200 ns instruction cycle
VSS
4
N/C
5
RC6
RA0
6
RC5
EPROM/
ROM
RA1
7
RC4
Device
Pins I/O
RAM
RA2
8
RC3
RA3
9
RC2
PIC16C54A
PIC16CR54A
PIC16CR54B
PIC16CR56
PIC16CR57A
PIC16CR57B
PIC16C58A
PIC16CR58A
PIC16CR58B
18
18
18
18
28
28
18
18
18
12
12
12
12
20
20
12
12
12
512
512
512
1K
25
25
25
25
72
72
73
73
73
RB0
10
RC1
RB1
11
RC0
RB2
12
RB7
RB3
13
RB6
RB4
14
RB5
2K
2K
2K
• Selectable oscillator options:
2K
- RC:
- XT:
- HS:
- LP:
Low-cost RC oscillator
2K
Standard crystal/resonator
High-speed crystal/resonator
• 12-bit wide instructions
• 8-bit wide data path
Power saving, low frequency crystal
• Seven or eight special function hardware
registers
CMOS Technology
• Low-power, high-speed CMOS EPROM/ROM
technology
• Two-level deep hardware stack
• Direct, indirect and relative addressing modes for
data and instructions
• Fully static design
• Wide-operating voltage range:
- EPROM Commercial/Industrial 2.5V to 6.25V
- ROM Commercial/Industrial 2.5V to 6.25V
- EPROM Automotive 2.5V to 6.0V
• Low-power consumption
Peripheral Features
• 8-bit real time clock/counter (TMR0) with 8-bit
programmable prescaler
• Power-On Reset (POR)
• Device Reset Timer (DRT)
- < 2 mA typical @ 5V, 4 MHz
- 15 µA typical @ 3V, 32 kHz
• Watchdog Timer (WDT) with its own on-chip RC
oscillator for reliable operation
- < 0.6 µA typical standby current (with WDT
disabled) @ 3V, 0°C to 70°C
• Programmable code-protection
• Power saving SLEEP mode
1996 Microchip Technology Inc.
DS30236B-page 1
Enhanced PIC16C5X
Pin Diagrams (con’t)
SSOP
SSOP
VSS
•1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
MCLR/VPP
OSC1/CLKIN
OSC2/CLKOUT
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RA2
RA3
T0CKI
MCLR/VPP
VSS
•1
2
3
20
19
18
17
16
15
14
13
12
11
RA1
RA0
OSC1/CLKIN
OSC2/CLKOUT
T0CKI
VDD
VDD
RA0
RA1
RA2
RA3
RB0
RB1
RB2
RB3
RB4
VSS
4
5
6
7
8
VDD
VDD
RB7
RB6
RB5
RB4
VSS
RB0
RB1
RB2
RB3
9
10
RC0
RB7
RB6
RB5
Table of Contents
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
General Description.............................................................................................................................................3
Enhanced PIC16C5X Device Varieties................................................................................................................5
Architectural Overview.........................................................................................................................................7
Memory Organization ........................................................................................................................................13
I/O Ports.............................................................................................................................................................23
Timer0 Module and TMR0 Register...................................................................................................................25
Special Features of the CPU .............................................................................................................................29
Instruction Set Summary ...................................................................................................................................41
Development Support........................................................................................................................................53
10.0 Electrical Characteristics - PIC16C54A .............................................................................................................59
11.0 Electrical Characteristics - PIC16CR54A...........................................................................................................71
12.0 Electrical Characteristics - PIC16CR54B/56/58B ..............................................................................................85
13.0 Electrical Characteristics - PIC16CR57A...........................................................................................................99
14.0 Electrical Characteristics - PIC16CR57B.........................................................................................................111
15.0 Electrical Characteristics - PIC16C58A ...........................................................................................................125
16.0 Electrical Characteristics - PIC16CR58A.........................................................................................................137
17.0 DC and AC Characteristics - All Enh. PIC16C5X, Except PIC16CR54A.........................................................151
18.0 DC and AC Characteristics - PIC16CR54A.....................................................................................................163
19.0 Packaging Information.....................................................................................................................................173
Appendix A: Compatibility................................................................................................................................185
Appendix B: What’s New .................................................................................................................................185
Appendix C: What’s Changed..........................................................................................................................186
Appendix D:PIC16/17 Microcontrollers............................................................................................................187
Index................................................................................................................................................................195
Connecting to Microchip BBS..........................................................................................................................199
Access to the Internet......................................................................................................................................199
Reader Response............................................................................................................................................200
Enhanced PIC16C5X Product Identification System.......................................................................................201
To Our Valued Customers
We constantly strive to improve the quality of all our products and documentation. We have spent an exceptional
amount of time to ensure that these documents are correct. However, we realize that we may have missed a few
things. If you find any information that is missing or appears in error, please use the reader response form in the
back of this data sheet to inform us. We appreciate your assistance in making this a better document.
To assist you in the use of this document, Appendix B contains a list of new information in this data sheet, while
Appendix C contains information that has changed.
DS30236B-page 2
1996 Microchip Technology Inc.
Enhanced PIC16C5X
1.1
Applications
1.0
GENERAL DESCRIPTION
The Enhanced PIC16C5X from Microchip Technology
is a family of low-cost, high performance, 8-bit, fully
static, EPROM/ROM-based CMOS microcontrollers.
This family is pin and software compatible with the
PIC16C5X family of devices in a new enhanced
process technology. It employs a RISC architecture
with only 33 single word/single cycle instructions. All
instructions are single cycle (200 ns) except for
program branches which take two cycles. The
Enhanced PIC16C5X delivers performance an order of
magnitude higher than its competitors in the same
price category. The 12-bit wide instructions are highly
symmetrical resulting in 2:1 code compression over
other 8-bit microcontrollers in its class. The easy to use
and easy to remember instruction set reduces
development time significantly.
The PIC16C5X series fits perfectly in applications
ranging from high-speed automotive and appliance
motor control to low-power remote transmitters/receiv-
ers, pointing devices and telecom processors. The
EPROM technology makes customizing application
programs (transmitter codes, motor speeds, receiver
frequencies, etc.) extremely fast and convenient. The
small footprint packages, for through hole or surface
mounting, make this microcontroller series perfect for
applications with space limitations. Low-cost,
low-power, high performance, ease of use and I/O flex-
ibility make the PIC16C5X series very versatile even in
areas where no microcontroller use has been
considered before (e.g., timer functions, replacement
of “glue” logic in larger systems, coprocessor
applications).
The Enhanced PIC16C5X products are equipped with
special features that reduce system cost and power
requirements. The Power-On Reset (POR) and Device
Reset Timer (DRT) eliminate the need for external
reset circuitry. There are four oscillator configurations
to choose from, including the power-saving LP (Low
Power) oscillator and cost saving RC oscillator. Power
saving SLEEP mode, Watchdog Timer and code
protection features improve system cost, power and
reliability.
The UV erasable CERDIP packaged versions are ideal
for code development, while the cost-effective
One-Time-Programmable (OTP) versions are suitable
for production in any volume. The customer can take
full advantage of Microchip’s price leadership in OTP
microcontrollers while benefiting from the OTP’s
flexibility.
The PIC16C5X products are supported by
a
full-featured macro assembler, a software simulator, an
in-circuit emulator, a ‘C’ compiler, fuzzy logic support
tools, a low-cost development programmer, and a full
featured programmer. All the tools are supported on
IBM PC and compatible machines.
1996 Microchip Technology Inc.
DS30236B-page 3
Enhanced PIC16C5X
TABLE 1-1:
ENHANCED PIC16C5X FAMILY OF DEVICES
Clock
Memory
Peripherals
Features
PIC16C54
20 512
20 512
—
—
25
25
TMR0
TMR0
TMR0
12 2.5-6.25 33 18-pin DIP, SOIC; 20-pin SSOP
12 2.5-6.25 33 18-pin DIP, SOIC; 20-pin SSOP
12 2.0-6.25 33 18-pin DIP, SOIC; 20-pin SSOP
PIC16C54A
(2)
20
—
512 25
PIC16CR54
PIC16CR54A
20
20
—
—
512 25
512 25
TMR0
TMR0
12 2.0-6.25 33 18-pin DIP, SOIC; 20-pin SSOP
(1)
12
2.5-5.5
33 18-pin DIP, SOIC; 20-pin SSOP
PIC16CR54B
PIC16C55
20 512
—
—
24
25
25
TMR0
TMR0
TMR0
20 2.5-6.25 33 28-pin DIP, SOIC, SSOP
PIC16C56
20
20
1K
—
12 2.5-6.25 33 18-pin DIP, SOIC; 20-pin SSOP
(1)
1K
12
2.5-5.5
33 18-pin DIP, SOIC; 20-pin SSOP
PIC16CR56
PIC16C57
20
20
2K
—
—
72
72
TMR0
TMR0
20 2.5-6.25 33 28-pin DIP, SOIC, SSOP
20 2.5-6.25 33 28-pin DIP, SOIC, SSOP
(2)
2K
PIC16CR57A
20
—
2K
72
TMR0
20 2.5-6.25 33 28-pin DIP, SOIC, SSOP
PIC16CR57B
PIC16C58A
PIC16CR58A
20
20
20
2K
—
—
—
2K
2K
73
73
73
TMR0
TMR0
TMR0
12 2.5-6.25 33 18-pin DIP, SOIC; 20-pin SSOP
12 2.5-6.25 33 18-pin DIP, SOIC; 20-pin SSOP
(1)
12
2.5-5.5
33 18-pin DIP, SOIC; 20-pin SSOP
PIC16CR58B
Legend: Grayed boxes: Devices NOT covered in this data sheet.
All PIC16/17 Family devices have Power-On Reset, selectable Watchdog Timer, selectable code protect and
high I/O current capability.
Note 1: Please contact your local sales office for availability of these devices.
2: Not recommended for new designs.
DS30236B-page 4
1996 Microchip Technology Inc.
Enhanced PIC16C5X
2.3
Quick-Turnaround-Production (QTP)
Devices
2.0
ENHANCED PIC16C5X DEVICE
VARIETIES
A variety of frequency ranges and packaging options
are available. Depending on application and
production requirements, the proper device option can
be selected using the information in this section. When
placing orders, please use the Enhanced PIC16C5X
Product Identification System at the back of this data
sheet to specify the correct part number.
Microchip offers a QTP Programming Service for
factory production orders. This service is made
available for users who choose not to program a
medium to high quantity of units and whose code
patterns have stabilized. The devices are identical to
the OTP devices but with all EPROM locations and
configuration bit options already programmed by the
factory. Certain code and prototype verification
procedures apply before production shipments are
available. Please contact your Microchip Technology
sales office for more details.
For the Enhanced PIC16C5X family of devices, there
are four device types, as indicated in the device
number:
1. C, as in PIC16C54A. These devices have
EPROM program memory and operate over the
standard voltage range.
2.4
Serialized
Quick-Turnaround-Production
SM
2. LC, as in PIC16LC54A. These devices have
EPROM program memory and operate over an
extended voltage range.
(SQTP ) Devices
Microchip offers the unique programming service
where a few user-defined locations in each device are
programmed with different serial numbers. The serial
numbers may be random, pseudo-random or
sequential.
3. CR, as in PIC16CR54A. These devices have
ROM program memory and operate over the
standard voltage range.
4. LCR, as in PIC16LCR54A. These devices have
ROM program memory and operate over an
extended voltage range.
Serial programming allows each device to have a
unique number which can serve as an entry code,
password or ID number.
2.1
UV Erasable Devices
2.5
Read Only Memory (ROM) Devices
The UV erasable versions, offered in CERDIP
packages, are optimal for prototype development and
pilot programs
Microchip offers masked ROM versions of several of
the highest volume parts, giving the customer a low
cost option for high volume, mature products.
UV erasable devices can be programmed for any of
the four oscillator configurations. Microchip's
PICSTART and PRO MATE programmers both
support programming of the Enhanced PIC16C5X.
Third party programmers also are available; refer to
the Third Party Guide for a list of sources.
2.2
One-Time-Programmable (OTP)
Devices
The availability of OTP devices is especially useful for
customers expecting frequent code changes and
updates.
The OTP devices, packaged in plastic packages,
permit the user to program them once. In addition to
the program memory, the configuration bits must be
programmed.
1996 Microchip Technology Inc.
DS30236B-page 5
Enhanced PIC16C5X
NOTES:
DS30236B-page 6
1996 Microchip Technology Inc.
Enhanced PIC16C5X
The PIC16C5X device contains an 8-bit ALU and
working register. The ALU is a general purpose
arithmetic unit. It performs arithmetic and Boolean
functions between data in the working register and any
register file.
3.0
ARCHITECTURAL OVERVIEW
The high performance of the PIC16C5X family can be
attributed to a number of architectural features
commonly found in RISC microprocessors. To begin
with, the PIC16C5X uses a Harvard architecture in
which program and data are accessed on separate
buses. This improves bandwidth over traditional von
Neumann architecture where program and data are
fetched on the same bus. Separating program and
data memory further allows instructions to be sized
differently than the 8-bit wide data word. Instruction
opcodes are 12-bits wide making it possible to have all
single word instructions. A 12-bit wide program
memory access bus fetches a 12-bit instruction in a
single cycle. A two-stage pipeline overlaps fetch and
The ALU is 8-bits wide and capable of addition,
subtraction, shift and logical operations. Unless
otherwise mentioned, arithmetic operations are two's
complement in nature. In two-operand instructions,
typically one operand is the W (working) register. The
other operand is either a file register or an immediate
constant. In single operand instructions, the operand
is either the W register or a file register.
The W register is an 8-bit working register used for
ALU operations. It is not an addressable register.
execution
of
instructions.
Consequently,
all
Depending on the instruction executed, the ALU may
affect the values of the Carry (C), Digit Carry (DC),
and Zero (Z) bits in the STATUS register. The C and
DC bits operate as a borrow and digit borrow out bit,
respectively, in subtraction. See the SUBWFand ADDWF
instructions for examples.
instructions (33) execute in a single cycle (200ns @
20MHz) except for program branches.
The PIC16C54A/CR54A/CR54B address 512 x 12 of
program memory, the PIC16CR56 addresses 1K x 12
of program memory and the PIC16CR57A/CR57B and
PIC16C58A/CR58A/CR58B address 2K x 12 of
program memory. All program memory is internal.
A simplified block diagram is shown in Figure 3-1, with
the corresponding device pins described in Table 3-1
and Table 3-2.
The PIC16C5X can directly or indirectly address its
register files and data memory. All special function
registers including the program counter are mapped in
the data memory. The PIC16C5X has a highly
orthogonal (symmetrical) instruction set that makes it
possible to carry out any operation on any register
using any addressing mode. This symmetrical nature
and lack of ‘special optimal situations’ make
programming with the PIC16C5X simple yet efficient.
In addition, the learning curve is reduced significantly.
1996 Microchip Technology Inc.
DS30236B-page 7
Enhanced PIC16C5X
FIGURE 3-1: PIC16C5X SERIES BLOCK DIAGRAM
9-11
T0CKI
PIN
OSC1 OSC2 MCLR
CONFIGURATION WORD
9-11
EPROM/ROM
512 X 12 TO
2048 X 12
STACK 1
STACK2
“DISABLE” “OSC
PC
SELECT”
WATCHDOG
TIMER
12
2
“CODE
OSCILLATOR/
TIMING &
CONTROL
PROTECT”
INSTRUCTION
REGISTER
WDT TIME
OUT
CLKOUT
WDT/TMR0
PRESCALER
9
12
8
“SLEEP”
INSTRUCTION
DECODER
6
“OPTION”
OPTION REG.
FROM W
DIRECT ADDRESS
DIRECT RAM
ADDRESS
GENERAL
PURPOSE
REGISTER
FILE
5
5-7
8
(SRAM)
24, 25, 72 or
73 Bytes
STATUS
TMR0
FSR
8
DATA BUS
8
W
ALU
FROM W
8
FROM W
4
FROM W
8
8
4
8
“TRIS 5”
“TRIS 6”
“TRIS 7”
TRISB PORTB
TRISA PORTA
TRISC
PORTC
8
4
8
RC7:RC0
(28-Pin
RA3:RA0
RB7:RB0
Devices Only)
DS30236B-page 8
1996 Microchip Technology Inc.
Enhanced PIC16C5X
TABLE 3-1:
Name
PINOUT DESCRIPTION - PIC16C54A, PIC16CR54A, PIC16CR54B, PIC16CR56,
PIC16C58A, PIC16CR58A, PIC16CR58B
DIP, SOIC SSOP I/O/P Input
Description
No.
No. Type Levels
RA0
RA1
RA2
RA3
17
18
1
19
20
1
I/O
I/O
I/O
I/O
TTL
TTL
TTL
TTL
Bi-directional I/O port
2
2
RB0
RB1
RB2
RB3
RB4
RB5
RB6
RB7
6
7
8
7
8
9
10
11
12
13
14
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
Bi-directional I/O port
9
10
11
12
13
T0CKI
3
3
I
ST
Clock input to Timer0. Must be tied to VSS or VDD, if not in
use, to reduce current consumption.
MCLR/VPP
4
4
I
ST
Master clear (reset) input/programming voltage input. This
pin is an active low reset to the device. Voltage on the
MCLR/VPP pin must not exceed VDD to avoid unintended
entering of programming mode.
OSC1/CLKIN
16
15
18
17
I
ST
—
Oscillator crystal input/external clock source input.
OSC2/CLKOUT
O
Oscillator crystal output. Connects to crystal or resonator in
crystal oscillator mode. In RC mode, OSC2 pin outputs
CLKOUT which has 1/4 the frequency of OSC1, and denotes
the instruction cycle rate.
VDD
VSS
14
5
15,16
5,6
P
P
—
—
Positive supply for logic and I/O pins.
Ground reference for logic and I/O pins.
Legend: I = input, O = output, I/O = input/output,
P = power, — = Not Used, TTL = TTL input,
ST = Schmitt Trigger input
1996 Microchip Technology Inc.
DS30236B-page 9
Enhanced PIC16C5X
TABLE 3-2:
PINOUT DESCRIPTION - PIC16CR57A, PIC16CR57B
DIP, SOIC SSOP I/O/P Input
Name
Description
No.
No. Type Levels
RA0
RA1
RA2
RA3
6
7
8
9
5
6
7
8
I/O
I/O
I/O
I/O
TTL Bi-directional I/O port
TTL
TTL
TTL
RB0
RB1
RB2
RB3
RB4
RB5
RB6
RB7
10
11
12
13
14
15
16
17
9
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
TTL Bi-directional I/O port
10
11
12
13
15
16
17
TTL
TTL
TTL
TTL
TTL
TTL
TTL
RC0
RC1
RC2
RC3
RC4
RC5
RC6
RC7
18
19
20
21
22
23
24
25
18
19
20
21
22
23
24
25
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
TTL Bi-directional I/O port
TTL
TTL
TTL
TTL
TTL
TTL
TTL
T0CKI
1
2
I
ST
Clock input to Timer0. Must be tied to VSS or VDD if not in use
to reduce current consumption.
MCLR
28
28
I
ST
Master clear (reset) input. This pin is an active low reset to
the device.
OSC1/CLKIN
27
26
27
26
I
ST
—
Oscillator crystal input/external clock source input.
OSC2/CLKOUT
O
Oscillator crystal output. Connects to crystal or resonator in
crystal oscillator mode. In RC mode, OSC2 pin outputs
CLKOUT which has 1/4 the frequency of OSC1, and denotes
the instruction cycle rate.
VDD
VSS
N/C
2
4
3,4
1,14
—
P
P
—
—
—
Positive supply for logic and I/O pins.
Ground reference for logic and I/O pins.
Unused, do not connect
3,5
—
Legend: I = input, O = output, I/O = input/output,
P = power, — = Not Used,
TTL = TTL input, ST = Schmitt Trigger input
DS30236B-page 10
1996 Microchip Technology Inc.
Enhanced PIC16C5X
3.1
Clocking Scheme/Instruction Cycle
3.2
Instruction Flow/Pipelining
The clock input (OSC1/CLKIN pin) is internally divided
by four to generate four non-overlapping quadrature
clocks namely Q1, Q2, Q3 and Q4. Internally, the
program counter is incremented every Q1, and the
instruction is fetched from program memory and
latched into instruction register in Q4. It is decoded
and executed during the following Q1 through Q4. The
clocks and instruction execution flow is shown in
Figure 3-2 and Example 3-1.
An Instruction Cycle consists of four Q cycles (Q1, Q2,
Q3 and Q4). The instruction fetch and execute are
pipelined such that fetch takes one instruction cycle
while decode and execute takes another instruction
cycle. However, due to the pipelining, each instruction
effectively executes in one cycle. If an instruction
causes the program counter to change (e.g., GOTO)
then two cycles are required to complete the
instruction (Example 3-1).
A fetch cycle begins with the program counter (PC)
incrementing in Q1.
In the execution cycle, the fetched instruction is
latched into the Instruction Register (IR) in cycle Q1.
This instruction is then decoded and executed during
the Q2, Q3, and Q4 cycles. Data memory is read
during Q2 (operand read) and written during Q4
(destination write).
FIGURE 3-2: CLOCK/INSTRUCTION CYCLE
Q2
Q3
Q4
Q2
Q3
Q4
Q2
Q3
Q4
Q1
Q1
Q1
OSC1
Q1
Q2
Q3
Q4
PC
Internal
phase
clock
PC
PC+1
PC+2
OSC2/CLKOUT
(RC mode)
Fetch INST (PC)
Execute INST (PC-1)
Fetch INST (PC+1)
Execute INST (PC)
Fetch INST (PC+2)
Execute INST (PC+1)
EXAMPLE 3-1: INSTRUCTION PIPELINE FLOW
1. MOVLW 55H
Fetch 1
Execute 1
Fetch 2
2. MOVWF PORTB
3. CALL SUB_1
Execute 2
Fetch 3
Execute 3
Fetch 4
4. BSF
PORTA, BIT3
Flush
Fetch SUB_1 Execute SUB_1
All instructions are single cycle, except for any program branches. These take two cycles since the fetch
instruction is “flushed” from the pipeline while the new instruction is being fetched and then executed.
1996 Microchip Technology Inc.
DS30236B-page 11
Enhanced PIC16C5X
NOTES:
DS30236B-page 12
1996 Microchip Technology Inc.
Enhanced PIC16C5X
FIGURE 4-2: PIC16CR56 PROGRAM
MEMORY MAP AND STACK
4.0
MEMORY ORGANIZATION
PIC16C5X memory is organized into program memory
and data memory. For devices with more than 512
bytes of program memory, a paging scheme is used.
Program memory pages are accessed using one or
two STATUS register bits. For devices with a data
memory register file of more than 32 registers, a
banking scheme is used. Data memory banks are
accessed using the File Selection Register (FSR).
PC<9:0>
10
CALL, RETLW
Stack Level 1
Stack Level 2
000h
On-chip Program
0FFh
Memory (Page 0)
100h
4.1
Program Memory Organization
1FFh
200h
The PIC16C54A, PIC16CR54A and PIC16CR54B
have a 9-bit Program Counter (PC) capable of
addressing a 512 x 12 program memory space
(Figure 4-1). The PIC16CR56 has a 10-bit Program
Counter capable of addressing a 1K x 12 program
memory space (Figure 4-2). The PIC16CR57A,
PIC16CR57B, PIC16C58A, PIC16CR58A, and
PIC16CR58B have an 11-bit Program Counter
capable of addressing a 2K x 12 program memory
space (Figure 4-3). Accessing a location above the
On-chip Program
2FFh
Memory (Page 1)
300h
Reset Vector
3FFh
FIGURE 4-3: PIC16CR57A/CR57B/C58A/CR
58A/CR58B PROGRAM
MEMORY MAP AND STACK
physically implemented address will cause
wraparound.
a
PC<10:0>
11
CALL, RETLW
The reset vector for the PIC16C54A, PIC16CR54A
and PIC16CR54B is at 1FFh, for the PIC16CR56, at
3FFh and for the PIC16CR57A, PIC16CR57B,
PIC16C58A, PIC16CR58A, and PIC16CR58B, at
7FFh.
Stack Level 1
Stack Level 2
000h
On-chip Program
0FFh
Memory (Page 0)
100h
FIGURE 4-1: PIC16C54A/CR54A/CR54B
PROGRAM MEMORY MAP
AND STACK
1FFh
200h
On-chip Program
2FFh
PC<8:0>
Memory (Page 1)
300h
9
CALL, RETLW
3FFh
400h
Stack Level 1
Stack Level 2
On-chip Program
4FFh
Memory (Page 2)
500h
000h
5FFh
600h
On-chip
Program
Memory
0FFh
100h
On-chip Program
6FFh
Memory (Page 3)
700h
Reset Vector
7FFh
Reset Vector
1FFh
1996 Microchip Technology Inc.
DS30236B-page 13
Enhanced PIC16C5X
4.2
Data Memory Organization
FIGURE 4-4: PIC16C54A/CR54A/CR54B/CR
56 REGISTER FILE MAP
Data memory is composed of registers, or bytes of
RAM. Therefore, data memory for a device is specified
by its register file. The register file is divided into two
functional groups: special function registers and
general purpose registers.
File Address
INDF(1)
00h
TMR0
PCL
01h
02h
03h
04h
05h
06h
07h
The special function registers include the TMR0
register, the Program Counter (PC), the Status
Register, the I/O registers (ports), and the File Select
Register (FSR). In addition, special purpose registers
are used to control the I/O port configuration and
prescaler options.
STATUS
FSR
PORTA
PORTB
The general purpose registers are used for data and
control information under command of the instructions.
For the PIC16C54A, PIC16CR54A, PIC16CR54B and
PIC16CR56, the register file is composed of 7 special
function registers and 25 general purpose registers
(Figure 4-4).
General
Purpose
Registers
0Fh
10h
For the PIC16CR57A and PIC16CR57B, the register
file is composed of 8 special function registers, 24
general purpose registers and up to 48 additional
general purpose registers that may be addressed
using a banking scheme (Figure 4-5).
1Fh
Note 1: Not a physical register. See Section 4.7
For the PIC16C58A, PIC16CR58A and PIC16CR58B,
the register file is composed of 7 special function
registers, 25 general purpose registers and up to 48
additional general purpose registers that may be
addressed using a banking scheme (Figure 4-6).
4.2.1
GENERAL PURPOSE REGISTER FILE
The register file is accessed either directly or indirectly
through the file select register FSR (Section 4.7).
DS30236B-page 14
1996 Microchip Technology Inc.
Enhanced PIC16C5X
FIGURE 4-5: PIC16CR57A/CR57B REGISTER FILE MAP
FSR<6:5>
File Address
00h
00
01
10
11
INDF(1)
TMR0
PCL
20h
40h
60h
01h
02h
03h
04h
05h
06h
STATUS
FSR
Addresses map back to
addresses in Bank 0.
PORTA
PORTB
07h
08h
PORTC
General
Purpose
Registers
2Fh
30h
4Fh
50h
6Fh
0Fh
10h
1Fh
70h
General
Purpose
Registers
General
Purpose
Registers
General
Purpose
Registers
General
Purpose
Registers
3Fh
5Fh
7Fh
Bank 0
Bank 1
Bank 2
Bank 3
Note 1: Not a physical register. See Section 4.7
FIGURE 4-6: PIC16C58A/CR58A/CR58B REGISTER FILE MAP
FSR<6:5>
File Address
00h
00
01
10
11
INDF(1)
TMR0
PCL
20h
40h
60h
01h
02h
03h
04h
05h
STATUS
FSR
Addresses map back to
addresses in Bank 0.
PORTA
PORTB
06h
07h
General
Purpose
Registers
2Fh
30h
4Fh
50h
6Fh
0Fh
10h
1Fh
70h
General
Purpose
Registers
General
Purpose
Registers
General
Purpose
Registers
General
Purpose
Registers
3Fh
5Fh
7Fh
Bank 0
Bank 1
Bank 2
Bank 3
Note 1: Not a physical register. See Section 4.7
1996 Microchip Technology Inc.
DS30236B-page 15
Enhanced PIC16C5X
4.2.2
SPECIAL FUNCTION REGISTERS
The special registers can be classified into two sets.
The special function registers associated with the
“core” functions are described in this section. Those
related to the operation of the peripheral features are
described in the section for each peripheral feature.
The Special Function Registers are registers used by
the CPU and peripheral functions to control the
operation of the device (Table 4-1).
TABLE 4-1:
SPECIAL FUNCTION REGISTER SUMMARY
Value on
Power-On
Reset
Value on
MCLR and
WDT Reset
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
N/A
N/A
00h
01h
TRIS
I/O control registers (TRISA, TRISB, TRISC)
1111 1111 1111 1111
--11 1111 --11 1111
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
OPTION
INDF
Contains control bits to configure Timer0 and Timer0/WDT prescaler
Uses contents of FSR to address data memory (not a physical register)
8-bit real-time clock/counter
TMR0
(1)
02h
03h
04h
05h
06h
PCL
Low order 8 bits of PC
1111 1111 1111 1111
0001 1xxx 000q quuu
1xxx xxxx 1uuu uuuu
---- xxxx ---- uuuu
xxxx xxxx uuuu uuuu
STATUS
FSR
PA2
PA1
PA0
TO
PD
Z
DC
C
Indirect data memory address pointer
PORTA
PORTB
—
—
—
—
RA3
RB3
RA2
RB2
RA1
RB1
RA0
RB0
RB7
RB6
RB5
RB4
(2)
07h
PORTC
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
xxxx xxxx uuuu uuuu
Legend: Shaded boxes = unimplemented or unused, –= unimplemented, read as '0' (if applicable)
x= unknown, u= unchanged, q= see the tables in Section 7.7 for possible values.
Note 1: The upper byte of the Program Counter is not directly accessible. See Section 4.5
for an explanation of how to access these bits.
2: File address 07h is a general purpose register on the PIC16C54A, PIC16CR54A, PIC16CR54B, PIC16CR56,
PIC16C58A, PIC16CR58A and PIC16CR58B.
DS30236B-page 16
1996 Microchip Technology Inc.
Enhanced PIC16C5X
For example, CLRF STATUSwill clear the upper three
bits and set the Z bit. This leaves the STATUS register
as 000u u1uu(where u= unchanged).
4.3
STATUS Register
This register contains the arithmetic status of the ALU,
the RESET status, and the page preselect bits for
program memories larger than 512 words.
It is recommended, therefore, that only BCF, BSF and
MOVWF instructions be used to alter the STATUS
register because these instructions do not affect the Z,
DC or C bits from the STATUS register. For other
instructions, which do affect STATUS bits, see
Table 8-2, Instruction Set Summary.
The STATUS register can be the destination for any
instruction, as with any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to
the device logic. Furthermore, the TO and PD bits are
not writable. Therefore, the result of an instruction with
the STATUS register as destination may be different
than intended.
FIGURE 4-7: STATUS REGISTER (ADDRESS:03h)
R/W-0
PA2
R/W-0
PA1
R/W-0
PA0
R-1
TO
R-1
PD
R/W-x
Z
R/W-x
DC
R/W-x
C
R = Readable bit
W = Writable bit
- n = Value at POR reset
bit7
6
5
4
3
2
1
bit0
bit 7:
PA2: This bit unused at this time.
Use of the PA2 bit as a general purpose read/write bit is not recommended, since this may affect upward
compatibility with future products.
bit 6-5: PA1:PA0: Program page preselect bits (PIC16CR56/CR57A/CR57B/C58A/CR58A/CR58B)
00 = Page 0 (000h - 1FFh) - PIC16C56 and PIC16CR57A/CR57B/C58A/CR58A/CR58B
01 = Page 1 (200h - 3FFh) - PIC16C56 and PIC16CR57A/CR57B/C58A/CR58A/CR58B
10 = Page 2 (400h - 5FFh) - PIC16CR57A/CR57B/C58A/CR58A/CR58B
11 = Page 3 (600h - 7FFh) - PIC16CR57A/CR57B/C58A/CR58A/CR58B
Each page is 512 bytes.
Using the PA1:PA0 bits as general purpose read/write bits in devices which do not use them for program
page preselect is not recommended since this may affect upward compatibility with future products.
bit 4:
bit 3:
bit 2:
bit 1:
TO: Time-out bit
1 = After power-up, CLRWDTinstruction, or SLEEPinstruction
0 = A WDT time-out occurred
PD: Power-down bit
1 = After power-up or by the CLRWDTinstruction
0 = By execution of the SLEEPinstruction
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
DC: Digit carry/borrow bit (for ADDWFand SUBWFinstructions)
ADDWF
1 = A carry from the 4th low order bit of the result occurred
0 = A carry from the 4th low order bit of the result did not occur
SUBWF
1 = A borrow from the 4th low order bit of the result did not occur
0 = A borrow from the 4th low order bit of the result occurred
bit 0:
C: Carry/borrow bit (for ADDWF, SUBWFand RRF, RLFinstructions)
ADDWF
SUBWF
RRF or RLF
1 = A carry occurred
0 = A carry did not occur
1 = A borrow did not occur
0 = A borrow occurred
Load bit with LSb or MSb, respectively
1996 Microchip Technology Inc.
DS30236B-page 17
Enhanced PIC16C5X
4.4
OPTION Register
The OPTION register is a 6-bit wide, write-only
register which contains various control bits to
configure the Timer0/WDT prescaler and Timer0.
By executing the OPTION instruction, the contents of
the W register will be transferred to the OPTION
register. A RESET sets the OPTION<5:0> bits.
FIGURE 4-8: OPTION REGISTER
U-0
—
U-0
—
6
W-1
T0CS
5
W-1
T0SE
4
W-1
PSA
3
W-1
PS2
2
W-1
PS1
1
W-1
PS0
W = Writable bit
= Unimplemented bit
- n = Value at POR reset
U
bit7
bit0
bit 7-6: Unimplemented.
bit 5:
bit 4:
bit 3:
T0CS: Timer0 clock source select bit
1 = Transition on T0CKI pin
0 = Internal instruction cycle clock (CLKOUT)
T0SE: Timer0 source edge select bit
1 = Increment on high-to-low transition on T0CKI pin
0 = Increment on low-to-high transition on T0CKI pin
PSA: Prescaler assignment bit
1 = Prescaler assigned to the WDT
0 = Prescaler assigned to Timer0
bit 2-0: PS2:PS0: Prescaler rate select bits
Bit Value
Timer0 Rate WDT Rate
000
001
010
011
100
101
110
111
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
1 : 256
1 : 1
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
DS30236B-page 18
1996 Microchip Technology Inc.
Enhanced PIC16C5X
4.5
Program Counter
FIGURE 4-9: LOADING OF PC
BRANCH INSTRUCTIONS -
PIC16C54A/CR54A/CR54B
As a program instruction is executed, the Program
Counter (PC) will contain the address of the next
program instruction to be executed. The PC value is
increased by one every instruction cycle, unless an
instruction changes the PC.
GOTO Instruction
8
7
0
PCL
PC
For a GOTOinstruction, bits 8:0 of the PC are provided
by the GOTO instruction word. The PC Latch (PCL) is
mapped to PC<7:0> (Figure 4-9, Figure 4-10 and
Figure 4-11).
Instruction Word
CALL or Modify PCL Instruction
For the PIC16CR56, PIC16CR57A, PIC16CR57B,
PIC16C58A, PIC16CR58A and PIC16CR58B, a page
number must be supplied as well. Bit5 of the STATUS
register provides this to bit9 of the PC for the
PIC16CR56 (Figure 4-10). Bit5 and bit6 of the
STATUS register provide page information to bit9 and
bit10 of the PC for the PIC16CR57A, PIC16CR57B,
8
7
0
PCL
PC
Reset to '0'
Instruction Word
PIC16C58A,
(Figure 4-11).
PIC16CR58A
and
PIC16CR58B
FIGURE 4-10: LOADING OF PC
BRANCH INSTRUCTIONS -
PIC16CR56
For a CALL instruction, or any instruction where the
PCL is the destination, bits 7:0 of the PC again are
provided by the instruction word. However, PC<8>
does not come from the instruction word, but is always
cleared (Figure 4-9, Figure 4-10 and Figure 4-11).
GOTO Instruction
9
8
7
0
PC
PCL
Instructions where the PCL is the destination, or
Modify PCL instructions, include MOVWF PC, ADDWF
PC,and BSF PC,5.
Instruction Word
0
For the PIC16CR56, PIC16CR57A, PIC16CR57B,
PIC16C58A, PIC16CR58A and PIC16CR58B, a page
number again must be supplied. Bit5 of the STATUS
register provides this to bit9 of the PC for the
PIC16CR56 (Figure 4-10). Bit5 and bit6 of the
STATUS register provide page information to bit9 and
bit10 of the PC for the PIC16CR57A, PIC16CR57B,
PA0
7
STATUS
CALL or Modify PCL Instruction
PIC16C58A,
(Figure 4-11).
PIC16CR58A
and
PIC16CR58B
9
8
7
0
PC
PCL
Note: Because PC<8> is cleared in the CALL
instruction, or any Modify PCL instruction,
all subroutine calls or computed jumps are
limited to the first 256 locations of any pro-
gram memory page (512 words long).
Instruction Word
Reset to '0'
PA0
7
0
STATUS
1996 Microchip Technology Inc.
DS30236B-page 19
Enhanced PIC16C5X
4.5.2
EFFECTS OF RESET
FIGURE 4-11: LOADING OF PC
BRANCH INSTRUCTIONS -
PIC16CR57A/CR54B/C58A/CR
58A/CR58B
The Program Counter is set upon a RESET, which
means that the PC addresses the last location in the
last page i.e., the reset vector.
The STATUS register page preselect bits are cleared
upon a RESET, which means that page 0 is
pre-selected.
GOTO Instruction
10
9
8
7
0
PC
PCL
Therefore, upon a RESET, a GOTO instruction at the
reset vector location will automatically cause the
program to jump to page 0.
Instruction Word
2
PA1:PA0
7
0
4.6
Stack
PIC16C5X devices have a 9-bit, 10-bit or 11-bit wide,
two-level hardware push/pop stack (Figure 4-1,
Figure 4-2 and Figure 4-3 respectively).
STATUS
CALL or Modify PCL Instruction
A CALLinstruction will push the current value of stack
1 into stack 2 and then push the current program
counter value, incremented by one, into stack level 1.
If more than two sequential CALL’s are executed, only
the most recent two return addresses are stored.
10
9
8
7
0
PC
PCL
Instruction Word
A RETLWinstruction will pop the contents of stack level
1 into the program counter and then copy stack level 2
contents into level 1. If more than two sequential
RETLW’s are executed, the stack will be filled with the
address previously stored in level 2. Note that the
W register will be loaded with the literal value specified
in the instruction. This is particularly useful for the
implementation of data look-up tables within the
program memory.
Reset to ‘0’
PA1:PA0
2
7
0
STATUS
For the RETLW instruction, the PC is loaded with the
Top Of Stack (TOS) contents. All of the devices
covered in this data sheet have a two-level stack. The
stack has the same bit width as the device PC.
4.5.1
PAGING CONSIDERATIONS –
PIC16CR56/CR57A/CR57B/C58A/CR58A/C
R58B
If the Program Counter is pointing to the last address
of a selected memory page, when it increments it will
cause the program to continue in the next higher page.
However, the page preselect bits in the STATUS
register will not be updated. Therefore, the next GOTO,
CALL, or Modify PCL instruction will send the program
to the page specified by the page preselect bits (PA0
or PA1:PA0).
For example, a NOP at location 1FFh (page 0)
increments the PC to 200h (page 1). A GOTO xxx at
200h will return the program to address xxxh on page
0 (assuming that PA1:PA0 are clear).
To prevent this, the page preselect bits must be
updated under program control.
DS30236B-page 20
1996 Microchip Technology Inc.
Enhanced PIC16C5X
4.7
Indirect Data Addressing; INDF and
FSR Registers
EXAMPLE 4-2: HOW TO CLEAR RAM
USING INDIRECT
ADDRESSING
The INDF register is not
a physical register.
movlw 0x10
;initialize pointer
Addressing INDF actually addresses the register
whose address is contained in the FSR register (FSR
is a pointer). This is indirect addressing.
movwf FSR
; to RAM
;clear INDF register
NEXT
clrf
incf
INDF
FSR,F ;inc pointer
btfsc FSR,4 ;all done?
goto
NEXT
;NO, clear next
EXAMPLE 4-1: INDIRECT ADDRESSING
• Register file 05 contains the value 10h
• Register file 06 contains the value 0Ah
• Load the value 05 into the FSR register
• A read of the INDF register will return the value
of 10h
CONTINUE
:
;YES, continue
The FSR is either a 5-bit (PIC16C54A, PIC16CR54A,
or PIC16CR54B) or 7-bit (PIC16CR56, PIC16CR57A,
PIC16CR57B,
PIC16C58A,
PIC16CR58A,
or
PIC16CR58B) wide register. It is used in conjunction
with the INDF register to indirectly address the data
memory area. The last 2 bits, FSR<6:5>, are also
used on the PIC16C57 for direct addressing
(Figure 4-12).
• Increment the value of the FSR register by one
(FSR = 06)
• A read of the INDR register now will return the
value of 0Ah.
Reading INDF itself indirectly (FSR = 0) will produce
00h. Writing to the INDF register indirectly results in a
no-operation (although STATUS bits may be affected).
The FSR<4:0> bits are used to select data memory
addresses 00h to 1Fh.
PIC16C54A/CR54A/CR54B/CR56: Do not use
banking. FSR<6:5> are unimplemented and read
as '1's.
A simple program to clear RAM locations 10h-1Fh
using indirect addressing is shown in Example 4-2.
PIC16CR57A/CR57B/C58A/CR58A/CR58B:
FSR<6:5> are the bank select bits and are used to
select the bank to be addressed (00 = bank 0,
01= bank 1, 10= bank 2, 11= bank 3).
FIGURE 4-12: DIRECT/INDIRECT ADDRESSING
Direct Addressing
Indirect Addressing
(FSR)
4
(opcode)
0
5
(FSR)
0
6
4
5
6
location select
bank select
location select
bank
00
01
10
11
00h
Addresses map back
to addresses in Bank 0.
Data
Memory
0Fh
10h
(1)
1Fh
Bank 0
3Fh
Bank 1
5Fh
Bank 2
7Fh
Bank 3
Note 1: For register map detail see Section 4.2.
1996 Microchip Technology Inc.
DS30236B-page 21
Enhanced PIC16C5X
NOTES:
DS30236B-page 22
1996 Microchip Technology Inc.
Enhanced PIC16C5X
5.5
I/O Interfacing
5.0
I/O PORTS
As with any other register, the I/O registers can be
written and read under program control. However,
read instructions (e.g., MOVF PORTB,W) always read
the I/O pins independent of the pin’s input/output
modes. On RESET, all I/O ports are defined as input
(inputs are at hi-impedance) since the I/O control
registers (TRISA, TRISB, TRISC) are all set.
The equivalent circuit for an I/O port pin is shown in
Figure 5-1. All ports may be used for both input and
output operations. For input operations these ports are
non-latching. Any input must be present until read by
an input instruction (e.g., MOVF PORTB, W). The
outputs are latched and remain unchanged until the
output latch is rewritten. To use a port pin as output,
the corresponding direction control bit (in TRISA,
TRISB, TRISC) must be cleared (= 0). For use as an
input, the corresponding TRIS bit must be set. Any I/O
pin can be programmed individually as input or output.
5.1
PORTA
PORTA is a 4-bit I/O register. Only the low order 4 bits
are used (RA3:RA0). Bits 7-4 are unimplemented and
read as '0's.
FIGURE 5-1: EQUIVALENT CIRCUIT
FOR A SINGLE I/O PIN
5.2
PORTB
Data
Bus
PORTB is an 8-bit I/O register (PORTB<7:0>).
D
Q
Q
Data
Latch
5.3
PORTC
VDD
P
WR
Port
CK
PIC16CR57A/CR57B: 8-bit I/O register.
PIC16C54A/CR54A/CR54B/CR55/CR56/C58A/CR58
A/CR58B: General purpose register.
N
I/O
pin(1)
W
Reg
5.4
TRIS Registers
D
Q
Q
TRIS
Latch
The output driver control registers are loaded with the
contents of the W register by executing the TRIS f
instruction. A '1' from a TRIS register bit puts the
corresponding output driver in a hi-impedance mode.
A '0' puts the contents of the output data latch on the
selected pins, enabling the output buffer.
VSS
TRIS ‘f’
CK
Reset
Note:
A read of the ports reads the pins, not the
output data latches. That is, if an output
driver on a pin is enabled and driven high,
but the external system is holding it low, a
read of the port will indicate that the pin is
low.
RD Port
Note 1: I/O pins have protection diodes to VDD and VSS.
The TRIS registers are “write-only” and are set (output
drivers disabled) upon RESET.
TABLE 5-1:
SUMMARY OF PORT REGISTERS
Value on
Power-On
Reset
Value on
MCLR and
WDT Reset
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
N/A
05h
06h
TRIS
PORTA
I/O control registers (TRISA, TRISB, TRISC)
1111 1111 1111 1111
---- xxxx ---- uuuu
xxxx xxxx uuuu uuuu
—
—
—
—
RA3
RB3
RA2
RB2
RA1
RB1
RA0
RB0
PORTB
PORTC
RB7
RB6
RB5
RB4
(1)
07h
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
xxxx xxxx uuuu uuuu
Legend: Shaded boxes = unimplemented, read as ‘0’,
–= unimplemented, read as '0', x= unknown, u= unchanged
Note 1: File address 07h is a general purpose register on the PIC16C54/CR54/C56.
1996 Microchip Technology Inc.
DS30236B-page 23
Enhanced PIC16C5X
5.6
I/O Programming Considerations
EXAMPLE 5-1: READ-MODIFY-WRITE
INSTRUCTIONS ON AN
I/O PORT
;Initial PORT Settings
; PORTB<7:4> Inputs
5.6.1
BI-DIRECTIONAL I/O PORTS
Some instructions operate internally as read followed
by write operations. The BCFand BSFinstructions, for
example, read the entire port into the CPU, execute
the bit operation and re-write the result. Caution must
be used when these instructions are applied to a port
where one or more pins are used as input/outputs. For
example, a BSFoperation on bit5 of PORTB will cause
all eight bits of PORTB to be read into the CPU, bit5 to
be set and the PORTB value to be written to the output
latches. If another bit of PORTB is used as a
bi-directional I/O pin (say bit0) and it is defined as an
input at this time, the input signal present on the pin
itself would be read into the CPU and rewritten to the
data latch of this particular pin, overwriting the
previous content. As long as the pin stays in the input
mode, no problem occurs. However, if bit0 is switched
into output mode later on, the content of the data latch
may now be unknown.
; PORTB<3:0> Outputs
;PORTB<7:6> have external pull-ups and are
;not connected to other circuitry
;
;
;
PORT latch PORT pins
---------- ----------
BCF
BCF
MOVLW 03Fh
TRIS PORTB
PORTB, 7
PORTB, 6
;01pp pppp
;10pp pppp
;
11pp pppp
11pp pppp
;10pp pppp
10pp pppp
;
;Note that the user may have expected the pin
;values to be 00pp pppp. The 2nd BCF caused
;RB7 to be latched as the pin value (High).
5.6.2
SUCCESSIVE OPERATIONS ON I/O
PORTS
The actual write to an I/O port happens at the end of
an instruction cycle, whereas for reading, the data
must be valid at the beginning of the instruction cycle
(Figure 5-2). Therefore, care must be exercised if a
write followed by a read operation is carried out on the
same I/O port. The sequence of instructions should
allow the pin voltage to stabilize (load dependent)
before the next instruction, which causes that file to be
read into the CPU, is executed. Otherwise, the
previous state of that pin may be read into the CPU
rather than the new state. When in doubt, it is better to
separate these instructions with a NOP or another
instruction not accessing this I/O port.
Example 5-1 shows the effect of two sequential
read-modify-write instructions (e.g., BCF, BSF, etc.) on
an I/O port.
A pin actively outputting a high or a low should not be
driven from external devices at the same time in order
to change the level on this pin (“wired-or”,
“wired-and”). The resulting high output currents may
damage the chip.
FIGURE 5-2: SUCCESSIVE I/O OPERATION
Q4
Q4
Q4
Q1 Q2
Q4
Q3
Q3
Q3
Q3
Q1 Q2
PC
Q1 Q2
Q1 Q2
PC + 3
NOP
PC + 1
PC + 2
NOP
This example shows a write to PORTB
followed by a read from PORTB.
Instruction
fetched
MOVWF PORTB MOVF PORTB,W
Data setup time = (0.25 TCY – TPD)
where: TCY = instruction cycle.
TPD = propagation delay
RB7:RB0
Port pin
written here
Port pin
sampled here
Therefore, at higher clock frequencies, a
write followed by a read may be problematic.
Instruction
executed
MOVWF PORTB MOVF PORTB,W
NOP
(Write to
PORTB)
(Read
PORTB)
DS30236B-page 24
1996 Microchip Technology Inc.
Enhanced PIC16C5X
Counter mode is selected by setting the T0CS bit
(OPTION<5>). In this mode, Timer0 will increment
either on every rising or falling edge of pin T0CKI. The
incrementing edge is determined by the source edge
select bit T0SE (OPTION<4>). Clearing the T0SE bit
selects the rising edge. Restrictions on the external
clock input are discussed in detail in Section 6.1.
6.0
TIMER0 MODULE AND
TMR0 REGISTER
The Timer0 module has the following features:
• 8-bit timer/counter register, TMR0
- Readable and writable
• 8-bit software programmable prescaler
• Internal or external clock select
- Edge select for external clock
The prescaler may be used by either the Timer0
module or the Watchdog Timer, but not both. The
prescaler assignment is controlled in software by the
control bit PSA (OPTION<3>). Clearing the PSA bit
will assign the prescaler to Timer0. The prescaler is
not readable or writable. When the prescaler is
assigned to the Timer0 module, prescale values of
1:2, 1:4,..., 1:256 are selectable. Section 6.2 details
the operation of the prescaler.
Figure 6-1 is a simplified block diagram of the Timer0
module, while Figure 6-2 shows the electrical structure
of the Timer0 input.
Timer mode is selected by clearing the T0CS bit
(OPTION<5>). In timer mode, the Timer0 module will
increment every instruction cycle (without prescaler). If
TMR0 register is written, the increment is inhibited for
the following two cycles (Figure 6-3 and Figure 6-4).
The user can work around this by writing an adjusted
value to the TMR0 register.
A summary of registers associated with the Timer0
module is found in Table 6-1.
FIGURE 6-1: TIMER0 BLOCK DIAGRAM
Data bus
FOSC/4
0
1
PSout
8
1
0
Sync with
Internal
Clocks
TMR0 reg
T0CKI
pin
Programmable
PSout
Sync
(2)
Prescaler
(1)
(2 cycle delay)
T0SE
3
(1)
(1)
PS2, PS1, PS0
PSA
(1)
T0CS
Note 1: Bits T0CS, T0SE, PSA, PS2, PS1 and PS0 are located in the OPTION register.
2: The prescaler is shared with the Watchdog Timer (Figure 6-6).
FIGURE 6-2: ELECTRICAL STRUCTURE OF T0CKI PIN
RIN
T0CKI
pin
(1)
Schmitt Trigger
Input Buffer
N
(1)
VSS
VSS
Note 1: ESD protection circuits
1996 Microchip Technology Inc.
DS30236B-page 25
Enhanced PIC16C5X
FIGURE 6-3: TIMER0 TIMING:
INTERNAL CLOCK/NO PRESCALE
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
PC
(Program
Counter)
PC-1
PC
PC+1
PC+2
PC+3
PC+4
PC+5
PC+6
Instruction
Fetch
MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W
MOVWF TMR0
T0
T0+1
T0+2
NT0
NT0
NT0
NT0+1
NT0+2
Timer0
Instruction
Executed
Read TMR0
reads NT0 + 1
Read TMR0
reads NT0
Read TMR0
reads NT0
Read TMR0
reads NT0
Read TMR0
reads NT0 + 2
Write TMR0
executed
FIGURE 6-4: TIMER0 TIMING:
INTERNAL CLOCK/PRESCALE 1:2
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
PC
(Program
Counter)
PC-1
PC
PC+1
PC+2
PC+3
PC+4
PC+5
PC+6
MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W
MOVWF TMR0
Instruction
Fetch
T0
T0+1
NT0+1
0
NT0
Timer0
Instruction
Execute
Read TMR0
reads NT0
Read TMR0
reads NT0
Read TMR0
reads NT0
Read TMR0
reads NT0
Read TMR0
reads NT0 + 1
Write TMR0
executed
TABLE 6-1:
Address
REGISTERS ASSOCIATED WITH TIMER0
Value on
Power-On
Reset
Value on
MCLR and
WDT Reset
Name
Bit 7
Timer0 - 8-bit real-time clock/counter
T0CS T0SE PSA
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
01
TMR0
xxxx xxxx uuuu uuuu
N/A
OPTION
—
—
PS2
PS1
PS0 --11 1111 --11 1111
Legend: Shaded cells: Unimplemented bits,
-= unimplemented, x = unknown, u= unchanged,
DS30236B-page 26
1996 Microchip Technology Inc.
Enhanced PIC16C5X
When a prescaler is used, the external clock input is
divided by the asynchronous ripple counter-type
prescaler so that the prescaler output is symmetrical.
For the external clock to meet the sampling
requirement, the ripple counter must be taken into
account. Therefore, it is necessary for T0CKI to have a
period of at least 4TOSC (and a small RC delay of
40 ns) divided by the prescaler value. The only
requirement on T0CKI high and low time is that they
do not violate the minimum pulse width requirement of
10 ns. Refer to parameters 40, 41 and 42 in the
electrical specification of the desired device.
6.1
Using Timer0 with an External Clock
When an external clock input is used for Timer0, it
must meet certain requirements. The external clock
requirement is due to internal phase clock (TOSC)
synchronization. Also, there is a delay in the actual
incrementing of Timer0 after synchronization.
6.1.1
EXTERNAL CLOCK SYNCHRONIZATION
When no prescaler is used, the external clock input is
the same as the prescaler output. The synchronization
of T0CKI with the internal phase clocks is
accomplished by sampling the prescaler output on the
Q2 and Q4 cycles of the internal phase clocks
(Figure 6-5). Therefore, it is necessary for T0CKI to be
high for at least 2TOSC (and a small RC delay of 20 ns)
and low for at least 2TOSC (and a small RC delay of
20 ns). Refer to the electrical specification of the
desired device.
6.1.2
TIMER0 INCREMENT DELAY
Since the prescaler output is synchronized with the
internal clocks, there is a small delay from the time the
external clock edge occurs to the time the Timer0
module is actually incremented. Figure 6-5 shows the
delay from the external clock edge to the timer
incrementing.
FIGURE 6-5: TIMER0 TIMING WITH EXTERNAL CLOCK
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Small pulse
External Clock Input or
misses sampling
Prescaler Output (2)
(1)
External Clock/Prescaler
Output After Sampling
(3)
Increment Timer0 (Q4)
Timer0
T0
T0 + 1
T0 + 2
Note 1: Delay from clock input change to Timer0 increment is 3Tosc to 7Tosc. (Duration of Q = Tosc).
Therefore, the error in measuring the interval between two edges on Timer0 input = ± 4Tosc max.
2: External clock if no prescaler selected, Prescaler output otherwise.
3: The arrows indicate the points in time where sampling occurs.
1996 Microchip Technology Inc.
DS30236B-page 27
Enhanced PIC16C5X
following instruction sequence (Example 6-1) must be
executed when changing the prescaler assignment from
Timer0 to the WDT.
6.2
Prescaler
An 8-bit counter is available as a prescaler for the
Timer0 module, or as a postscaler for the Watchdog
Timer (WDT), respectively (Section 6.1.2). For
simplicity, this counter is being referred to as
“prescaler” throughout this data sheet. Note that the
prescaler may be used by either the Timer0 module or
the WDT, but not both. Thus, a prescaler assignment
for the Timer0 module means that there is no
prescaler for the WDT, and vice-versa.
EXAMPLE 6-1: CHANGING PRESCALER
(TIMER0→WDT)
CLRF
TMR0
;Clear TMR0
CLRWDT
;Clears WDT and
;prescaler
MOVLW 'xxxx1xxx'
OPTION
;Select new prescale
;value
The PSA and PS2:PS0 bits (OPTION<3:0>)
determine prescaler assignment and prescale ratio.
To change prescaler from the WDT to the Timer0
module, use the sequence shown in Example 6-2. This
sequence must be used even if the WDT is disabled. A
CLRWDTinstruction should be executed before switching
the prescaler.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g., CLRF 1, MOVWF 1,
BSF 1,x, etc.) will clear the prescaler. When
assigned to WDT, a CLRWDT instruction will clear the
prescaler along with the WDT. The prescaler is neither
readable nor writable. On a RESET, the prescaler
contains all '0's.
EXAMPLE 6-2: CHANGING PRESCALER
(WDT→TIMER0)
CLRWDT
;Clear WDT and
;prescaler
MOVLW 'xxxx0xxx'
;Select TMR0, new
;prescale value and
;clock source
6.2.1
SWITCHING PRESCALER ASSIGNMENT
The prescaler assignment is fully under software control
(i.e., it can be changed “on the fly” during program
execution). To avoid an unintended device RESET, the
OPTION
FIGURE 6-6: BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER
TCY ( = Fosc/4)
Data Bus
8
0
M
U
X
1
M
U
X
T0CKI
pin
1
Sync
2
Cycles
TMR0 reg
0
T0SE
T0CS
PSA
0
1
8-bit Prescaler
M
U
X
8
Watchdog
Timer
8 - to - 1MUX
PS2:PS0
PSA
1
0
WDT Enable bit
MUX
PSA
WDT
Time-Out
Note: T0CS, T0SE, PSA, PS2:PS0 are bits in the OPTION register.
DS30236B-page 28
1996 Microchip Technology Inc.
Enhanced PIC16C5X
The SLEEP mode is designed to offer a very low
current power-down mode. The user can wake up
from SLEEP through external reset or through a
Watchdog Timer time-out. Several oscillator options
are also made available to allow the part to fit the
application. The RC oscillator option saves system
cost while the LP crystal option saves power. A set of
configuration bits are used to select various options.
7.0
SPECIAL FEATURES OF THE
CPU
What sets
a
microcontroller apart from other
processors are special circuits to deal with the needs
of real-time applications. The PIC16C5X family of
microcontrollers has a host of such features intended
to maximize system reliability, minimize cost through
elimination of external components, provide power
saving operating modes and offer code protection.
These features are:
7.1
Configuration Bits
The PIC16C5X configuration word consists of 4 or 12
bits, depending on device configuration. Configuration
bits can be programmed to select various device
configurations. Two bits are for the selection of the
oscillator type and one bit is the Watchdog Timer
enable bit. One bit is the code protection bit
(Figure 7-1) for the PIC16C54A, PIC16CR57A or
PIC16C58A devices. Nine bits are code protection
bits (Figure 7-2) for the PIC16CR54A, PIC16CR54B,
• Oscillator selection
• Reset
• Power-On Reset (POR)
• Device Reset Timer (DRT)
• Watchdog Timer (WDT)
• SLEEP
• Code protection
• ID locations
PIC16CR56,
PIC16CR57B,
PIC16CR58A
or
PIC16CR58B devices.
The PIC16C5X has a Watchdog Timer which can be
shut off only through configuration bit WDTE. It runs
off of its own RC oscillator for added reliability. There
is an 18 ms delay provided by the Device Reset Timer
(DRT), intended to keep the chip in reset until the
crystal oscillator is stable. With this timer on-chip, most
applications need no external reset circuitry.
OTP, QTP or ROM devices have the oscillator
configuration programmed at the factory and these
parts are tested accordingly (see "Product
Identification System" on the inside back cover).
FIGURE 7-1: CONFIGURATION WORD FOR PIC16C54A/CR57A/C58A
—
—
—
9
—
8
—
7
—
6
—
5
—
4
CP
3
WDTE FOSC1 FOSC0
bit0
Register: CONFIG
(1)
Address
:
FFFh
bit11
10
2
1
bit 11-4: Unimplemented: Read as ’0’
bit 3:
CP: Code protection bit.
1 = Code protection off
0 = Code protection on
bit 2:
WDTE: Watchdog timer enable bit
1 = WDT enabled
0 = WDT disabled
bit 1-0: FOSC1:FOSC0: Oscillator selection bits
11 = RC oscillator
10 = HS oscillator
01 = XT oscillator
00 = LP oscillator
Note 1: Refer to the PIC16C5X Programming Specifications (literature number DS30190) to deter-
mine how to access the configuration word.
1996 Microchip Technology Inc.
DS30236B-page 29
Enhanced PIC16C5X
FIGURE 7-2: CONFIGURATION WORD FOR PIC16CR54A/CR54B/CR56/CR57B/CR58A/CR58B
CP
CP
10
CP
9
CP
8
CP
7
CP
6
CP
5
CP
4
CP
3
WDTE FOSC1 FOSC0
bit0
Register: CONFIG
(1)
Address
:
FFFh
bit11
2
1
bit 11-3: CP: Code protection bits
1 = Code protection off
0 = Code protection on
bit 2:
WDTE: Watchdog timer enable bit
1 = WDT enabled
0 = WDT disabled
bit 1-0: FOSC1:FOSC0: Oscillator selection bits
11 = RC oscillator
10 = HS oscillator
01 = XT oscillator
00 = LP oscillator
Note 1: Refer to the PIC16C5X Programming Specifications (literature number DS30190) to deter-
mine how to access the configuration word.
7.2
Oscillator Configurations
FIGURE 7-3: CRYSTAL OPERATION (OR
CERAMIC RESONATOR) (HS,
XT OR LP OSC
7.2.1
OSCILLATOR TYPES
CONFIGURATION)
The PIC16C5X can be operated in four different
oscillator modes. The user can program two
configuration bits (FOSC1:FOSC0) to select one of
these four modes:
(1)
C1
OSC1
PIC16C5X
SLEEP
• LP:
• XT:
• HS:
• RC:
Low Power Crystal
XTAL
(3)
RF
To internal
logic
Crystal/Resonator
OSC2
High Speed Crystal/Resonator
Resistor/Capacitor
(2)
RS
(1)
C2
7.2.2
CRYSTAL OSCILLATOR / CERAMIC
RESONATORS
Note 1: See Capacitor Selection tables for
recommended values of C1 and C2.
2: A series resistor (RS) may be required for
AT strip cut crystals.
In XT, LP or HS modes, a crystal or ceramic resonator
is connected to the OSC1/CLKIN and OSC2/CLKOUT
pins to establish oscillation (Figure 7-3). The
PIC16C5X oscillator design requires the use of a
parallel cut crystal. Use of a series cut crystal may
give a frequency out of the crystal manufacturers
specifications. When in XT, LP or HS modes, the
device can have an external clock source drive the
OSC1/CLKIN pin (Figure 7-4).
3: RF varies with the crystal chosen
(approx. value = 10 MΩ).
FIGURE 7-4: EXTERNAL CLOCK INPUT
OPERATION (HS, XT OR LP
OSC CONFIGURATION)
OSC1
OSC2
Clock from
ext. system
PIC16C5X
Open
DS30236B-page 30
1996 Microchip Technology Inc.
Enhanced PIC16C5X
TABLE 7-1:
CAPACITOR SELECTION
FOR CERAMIC RESONATORS
- ENH. PIC16C5X
TABLE 7-3:
CAPACITOR SELECTION
FOR CERAMIC RESONATORS
- ENH. PIC16CR5X
Osc
Resonator Cap. Range Cap. Range
Osc
Resonator Cap. Range Cap. Range
Type
Freq
C1
C2
Type
Freq
C1
C2
XT
455 kHz
2.0 MHz
4.0 MHz
68-100 pF
15-33 pF
10-22 pF
68-100 pF
15-33 pF
10-22 pF
Data not available at this time.
HS
8.0 MHz
16.0 MHz
10-22 pF
10 pF
10-22 pF
10 pF
TABLE 7-4:
CAPACITOR SELECTION
FOR CRYSTAL OSCILLATOR
- ENH. PIC16CR5X
These values are for design guidance only. Since
each resonator has its own characteristics, the user
should consult the resonator manufacturer for
appropriate values of external components.
Osc
Resonator Cap.Range Cap. Range
Type
Freq
C1
C2
TABLE 7-2:
CAPACITOR SELECTION
FOR CRYSTAL OSCILLATOR
- ENH. PIC16C5X
(1)
LP
32 kHz
15-33 pF
15-33 pF
15-30 pF
15-33 pF
15-33 pF
15-30 pF
100 kHz
200 kHz
Osc
Resonator Cap.Range Cap. Range
XT
100 kHz
200 kHz
1 MHz
2 MHz
4 MHz
68-100 pF
15-30 pF
15-47 pF
15-47 pF
15-47 pF
68-100 pF
15-30 pF
15-47 pF
15-47 pF
15-47 pF
Type
Freq
C1
C2
(1)
LP
XT
32 kHz
15 pF
15 pF
100 kHz
200 kHz
455 kHz
1 MHz
15-30 pF
15-30 pF
15-30 pF
15-30 pF
15 pF
200-300 pF
100-200 pF
15-100 pF
15-30 pF
15 pF
HS
4 MHz
8 MHz
20 MHz
15-47 pF
15-47 pF
15-47 pF
15-47 pF
15-47 pF
15-47 pF
2 MHz
4 MHz
15 pF
15 pF
Note 1: For VDD < 2.5V, C1 = C2 ≈ 15-33 pF is
recommended.
HS
4 MHz
8 MHz
20 MHz
15 pF
15 pF
15 pF
15 pF
15 pF
15 pF
These values are for design guidance only. Rs may
be required in HS mode as well as XT mode to avoid
overdriving crystals with low drive level specification.
Since each crystal has its own characteristics, the
user should consult the crystal manufacturer for
appropriate values of external components.
Note 1: For VDD > 4.5V, C1 = C2 ≈ 30 pF is
recommended.
These values are for design guidance only. Rs may
be required in HS mode as well as XT mode to avoid
overdriving crystals with low drive level specification.
Since each crystal has its own characteristics, the
user should consult the crystal manufacturer for
appropriate values of external components.
1996 Microchip Technology Inc.
DS30236B-page 31
Enhanced PIC16C5X
7.2.3
EXTERNAL CRYSTAL OSCILLATOR
CIRCUIT
7.2.4
RC OSCILLATOR
For timing insensitive applications, the RC device
option offers additional cost savings. The RC oscillator
frequency is a function of the supply voltage, the
resistor (Rext) and capacitor (Cext) values, and the
operating temperature. In addition to this, the oscillator
frequency will vary from unit to unit due to normal
process parameter variation. Furthermore, the
difference in lead frame capacitance between package
types will also affect the oscillation frequency,
especially for low Cext values. The user also needs to
take into account variation due to tolerance of external
R and C components used.
Either a prepackaged oscillator or a simple oscillator
circuit with TTL gates can be used as an external
crystal oscillator circuit. Prepackaged oscillators
provide a wide operating range and better stability. A
well-designed crystal oscillator will provide good
performance with TTL gates. Two types of crystal
oscillator circuits can be used: one with parallel
resonance, or one with series resonance.
Figure 7-5 shows implementation of
a
parallel
resonant oscillator circuit. The circuit is designed to
use the fundamental frequency of the crystal. The
74AS04 inverter performs the 180-degree phase shift
that a parallel oscillator requires. The 4.7 kΩ resistor
provides the negative feedback for stability. The 10 kΩ
potentiometers bias the 74AS04 in the linear region.
This circuit could be used for external oscillator
designs.
Figure 7-7 shows how the R/C combination is
connected to the PIC16C5X. For Rext values below
2.2 kΩ, the oscillator operation may become unstable,
or stop completely. For very high Rext values
(e.g., 1 MΩ) the oscillator becomes sensitive to noise,
humidity and leakage. Thus, we recommend keeping
Rext between 3 kΩ and 100 kΩ.
FIGURE 7-5: EXTERNAL PARALLEL
RESONANT CRYSTAL
Although the oscillator will operate with no external
capacitor (Cext = 0 pF), we recommend using values
above 20 pF for noise and stability reasons. With no or
small external capacitance, the oscillation frequency
can vary dramatically due to changes in external
capacitances, such as PCB trace capacitance or
package lead frame capacitance.
OSCILLATOR CIRCUIT
+5V
To Other
Devices
PIC16C5X
10k
74AS04
4.7k
CLKIN
74AS04
The Electrical Specifications sections show RC
frequency variation from part to part due to normal
process variation. The variation is larger for larger R
(since leakage current variation will affect RC
frequency more for large R) and for smaller C (since
variation of input capacitance will affect RC frequency
more).
10k
XTAL
10k
Also, see the Electrical Specifications sections for
variation of oscillator frequency due to VDD for given
Rext/Cext values as well as frequency variation due to
operating temperature for given R, C, and VDD values.
20 pF
20 pF
Figure 7-6 shows a series resonant oscillator circuit.
This circuit is also designed to use the fundamental
frequency of the crystal. The inverter performs a
180-degree phase shift in a series resonant oscillator
circuit. The 330 Ω resistors provide the negative
feedback to bias the inverters in their linear region.
The oscillator frequency, divided by 4, is available on
the OSC2/CLKOUT pin, and can be used for test
purposes or to synchronize other logic.
FIGURE 7-7: RC OSCILLATOR MODE
VDD
FIGURE 7-6: EXTERNAL SERIES
RESONANT CRYSTAL
Rext
OSCILLATOR CIRCUIT
Internal
clock
OSC1
N
To Other
Devices
330
330
PIC16C5X
PIC16C5X
74AS04
74AS04
74AS04
Cext
VSS
CLKIN
0.1 µF
Fosc/4
OSC2/CLKOUT
XTAL
DS30236B-page 32
1996 Microchip Technology Inc.
Enhanced PIC16C5X
Some registers are not affected in any reset condition.
Their status is unknown on POR and unchanged in
any other reset. Most other registers are reset to a
“reset state” on Power-On Reset (POR), MCLR or
WDT reset. A MCLR or WDT wake-up from SLEEP
also results in a device reset, and not a continuation of
operation before SLEEP.
7.3
Reset
PIC16C5X devices may be reset in one of the
following ways:
• Power-On Reset (POR)
• MCLR reset (normal operation)
• MCLR wake-up reset (from SLEEP)
• WDT reset (normal operation)
• WDT wake-up reset (from SLEEP)
The TO and PD bits (STATUS <4:3>) are set or
cleared depending on the different reset conditions
(Section 7.7). These bits may be used to determine
the nature of the reset.
Table 7-5 shows these reset conditions for the PCL
and STATUS registers.
Table 7-6 lists a full description of reset states of all
registers. Figure 7-8 shows a simplified block diagram
of the on-chip reset circuit.
TABLE 7-5:
RESET CONDITIONS FOR SPECIAL REGISTERS
PCL
Addr: 02h
STATUS
Addr: 03h
Condition
1111 1111
1111 1111
1111 1111
1111 1111
1111 1111
0001 1xxx
Power-On Reset
(1)
000u uuuu
MCLR reset (normal operation)
MCLR wake-up (from SLEEP)
WDT reset (normal operation)
WDT wake-up (from SLEEP)
0001 0uuu
(2)
0000 1uuu
0000 0uuu
Legend: u= unchanged, x= unknown, -= unimplemented read as '0'.
Note 1: TO and PD bits retain their last value until one of the other reset conditions occur.
2: The CLRWDTinstruction will set the TO and PD bits.
TABLE 7-6:
RESET CONDITIONS FOR ALL REGISTERS
Register
W
Address
N/A
Power-On Reset
xxxx xxxx
1111 1111
--11 1111
xxxx xxxx
xxxx xxxx
1111 1111
MCLR or WDT Reset
uuuu uuuu
1111 1111
TRIS
N/A
--11 1111
OPTION
INDF
N/A
uuuu uuuu
00h
uuuu uuuu
TMR0
PCL(1)
01h
1111 1111
02h
STATUS(1)
0001 1xxx
000q quuu
03h
1xxx xxxx
---- xxxx
xxxx xxxx
xxxx xxxx
1uuu uuuu
---- uuuu
uuuu uuuu
uuuu uuuu
FSR
04h
05h
06h
07h
PORTA
PORTB
PORTC(2)
xxxx xxxx
uuuu uuuu
General Purpose
register files
08-7Fh
Legend: u= unchanged, x= unknown, -= unimplemented, read as '0',
q= see tables in Section 7.7 for possible values.
Note 1: See Table 7-5 for reset value for specific conditions.
2: General purpose register file on the PIC16C54/CR54/C56.
1996 Microchip Technology Inc.
DS30236B-page 33
Enhanced PIC16C5X
FIGURE 7-8: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
Power-Up
Detect
POR (Power-On Reset)
VDD
MCLR/VPP pin
WDT Time-out
8-bit Asynch
RESET
S
R
Q
Q
On-Chip
RC OSC
Ripple Counter
(Start-Up Timer)
CHIP RESET
DS30236B-page 34
1996 Microchip Technology Inc.
Enhanced PIC16C5X
7.4
Power-On Reset (POR)
FIGURE 7-9: ELECTRICAL STRUCTURE OF
MCLR/VPP PIN
The PIC16C5X family incorporates on-chip Power-On
Reset (POR) circuitry which provides an internal chip
reset for most power-up situations. To use this feature,
the user merely ties the MCLR/VPP pin (Figure 7-9) to
VDD. A simplified block diagram of the on-chip
Power-On Reset circuit is shown in Figure 7-8.
RIN
(1)
MCLR/VPP
Pin
Schmitt Trigger
Input Buffer
(1)
N
The Power-On Reset circuit and the Device Reset
Timer (Section 7.5) circuit are closely related. On
power-up, the reset latch is set and the DRT is reset.
The DRT timer begins counting once it detects MCLR
to be high. After the time-out period, which is typically
18 ms, it will reset the reset latch and thus end the
on-chip reset signal.
VSS
VSS
Note 1: ESD protection circuits
FIGURE 7-10: EXTERNAL POWER-ON
RESET CIRCUIT (FOR SLOW
VDD POWER-UP)
A power-up example where MCLR is not tied to VDD is
shown in Figure 7-11. VDD is allowed to rise and
stabilize before bringing MCLR high. The chip will
actually come out of reset TDRT msec after MCLR
goes high.
VDD
VDD
D
R
In Figure 7-12, the on-chip Power-On Reset feature is
being used (MCLR and VDD are tied together). The
VDD is stable before the start-up timer times out and
there is no problem in getting a proper reset. However,
Figure 7-13 depicts a problem situation where VDD
rises too slowly. The time between when the DRT
senses a high on the MCLR/VPP pin, and when the
MCLR/VPP pin (and VDD) actually reach their full
value, is too long. In this situation, when the start-up
timer times out, VDD has not reached the VDD (min)
value and the chip is, therefore, not guaranteed to
function correctly. For such situations, we recommend
that external RC circuits be used to achieve longer
POR delay times (Figure 7-10).
R1
MCLR
PIC16C5X
C
• External Power-On Reset circuit is required
only if VDD power-up is too slow. The diode D
helps discharge the capacitor quickly when
VDD powers down.
• R < 40 kΩ is recommended to make sure that
voltage drop across R does not violate the
device electrical specification.
• R1 = 100Ω to 1 kΩ will limit any current
flowing into MCLR from external capacitor C
in the event of MCLR pin breakdown due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS).
Note: When the device starts normal operation
(exits the reset condition), device operat-
ing parameters (voltage, frequency, tem-
perature, etc.) must be meet to ensure
operation. If these conditions are not met,
the device must be held in reset until the
operating conditions are met.
For more information on PIC16C5X POR, see
Power-Up Considerations - AN522 in the Embedded
Control Handbook.
The POR circuit does not produce an internal reset
when VDD declines.
1996 Microchip Technology Inc.
DS30236B-page 35
Enhanced PIC16C5X
FIGURE 7-11: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD)
VDD
MCLR
INTERNAL POR
TDRT
DRT TIME-OUT
INTERNAL RESET
FIGURE 7-12: TIME-OUT SEQUENCE ON POWER-UP (MCLRTIED TO VDD): FAST VDD RISE TIME
VDD
MCLR
INTERNAL POR
TDRT
DRT TIME-OUT
INTERNAL RESET
FIGURE 7-13: TIME-OUT SEQUENCE ON POWER-UP (MCLRTIED TO VDD): SLOW VDD RISETIME
V1
VDD
MCLR
INTERNAL POR
TDRT
DRT TIME-OUT
INTERNAL RESET
When VDD rises slowly, the TDRT time-out expires long before VDD has reached its final value. In
this example, the chip will reset properly if, and only if, V1 ≥ VDD min.
DS30236B-page 36
1996 Microchip Technology Inc.
Enhanced PIC16C5X
7.5
Device Reset Timer (DRT)
7.6
Watchdog Timer (WDT)
The Device Reset Timer (DRT) provides a fixed 18 ms
nominal time-out on reset. The DRT operates on an
internal RC oscillator. The processor is kept in RESET
as long as the DRT is active. The DRT delay allows
VDD to rise above VDD min., and for the oscillator to
stabilize.
The Watchdog Timer (WDT) is a free running on-chip
RC oscillator which does not require any external
components. This RC oscillator is separate from the
RC oscillator of the OSC1/CLKIN pin. That means that
the WDT will run even if the clock on the OSC1/CLKIN
and OSC2/CLKOUT pins have been stopped, for
example, by execution of a SLEEPinstruction. During
normal operation or SLEEP, a WDT reset or wake-up
reset generates a device RESET.
Oscillator circuits based on crystals or ceramic
resonators require a certain time after power-up to
establish a stable oscillation. The on-chip DRT keeps
the device in a RESET condition for approximately 18
ms after the voltage on the MCLR/VPP pin has
reached a logic high (VIHMC) level. Thus, external RC
networks connected to the MCLR input are not
required in most cases, allowing for savings in
cost-sensitive and/or space restricted applications.
The TO bit (STATUS<4>) will be cleared upon a
Watchdog Timer reset.
The WDT can be permanently disabled by
programming the configuration bit WDTE as a '0'
(Section 7.1). Refer to the PIC16C5X Programming
Specifications (literature number DS30190) to
determine how to access the configuration word.
The Device Reset time delay will vary from chip to chip
due to VDD, temperature, and process variation. See
AC parameters for details.
7.6.1
WDT PERIOD
The DRT will also be triggered upon a Watchdog
Timer time-out. This is particularly important for
applications using the WDT to wake the PIC16C5X
from SLEEP mode automatically.
The WDT has a nominal time-out period of 18 ms,
(with no prescaler). If a longer time-out period is
desired, a prescaler with a division ratio of up to 1:128
can be assigned to the WDT (under software control)
by writing to the OPTION register. Thus, time-out a
period of a nominal 2.3 seconds can be realized.
These periods vary with temperature, VDD and
part-to-part process variations (see DC specs).
Under worst case conditions (VDD = Min., Temperature
= Max., max. WDT prescaler), it may take several
seconds before a WDT time-out occurs.
7.6.2
WDT PROGRAMMING CONSIDERATIONS
The CLRWDT instruction clears the WDT and the
postscaler, if assigned to the WDT, and prevents it
from timing out and generating a device RESET.
The SLEEP instruction resets the WDT and the
postscaler, if assigned to the WDT. This gives the
maximum SLEEP time before a WDT wake-up reset.
1996 Microchip Technology Inc.
DS30236B-page 37
Enhanced PIC16C5X
FIGURE 7-14: WATCHDOG TIMER BLOCK DIAGRAM
From Timer0 Clock Source
(Figure 6-5)
0
M
Postscaler
1
Watchdog
Timer
U
X
8 - to - 1 MUX
PS2:PS0
PSA
WDT Enable
EPROM Bit
To Timer0 (Figure 6-5)
1
0
PSA
MUX
Note: T0CS, T0SE, PSA, PS2:PS0
are bits in the OPTION register.
WDT
Time-out
TABLE 7-7:
SUMMARY OF REGISTERS ASSOCIATED WITH THE WATCHDOG TIMER
Value on
Power-On
Reset
Value on
MCLR and
WDT Reset
Address
Name
OPTION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
N/A
—
—
T0CS
T0SE
PSA
PS2
PS1
PS0
--11 1111 --11 1111
Legend: Shaded boxes = Not used by Watchdog Timer,
–= unimplemented, read as '0', u= unchanged
DS30236B-page 38
1996 Microchip Technology Inc.
Enhanced PIC16C5X
7.7
Time-Out Sequence and Power Down
Status Bits (TO/PD)
7.8
Reset on Brown-Out
A brown-out is a condition where device power (VDD)
dips below its minimum value, but not to zero, and
then recovers. The device should be reset in the event
of a brown-out.
The TO and PD bits in the STATUS register can be
tested to determine if a RESET condition has been
caused by
a power-up condition, a MCLR or
Watchdog Timer (WDT) reset, or a MCLR or WDT
wake-up reset.
To reset PIC16C5X devices when a brown-out occurs,
external brown-out protection circuits may be built, as
shown in Figure 7-15 and Figure 7-16.
TABLE 7-8:
TO/PD STATUS AFTER
RESET
FIGURE 7-15: BROWN-OUT PROTECTION
CIRCUIT 1
TO
PD
RESET was caused by
Power-up (POR)
1
u
1
u
VDD
(1)
MCLR reset (normal operation)
VDD
1
0
0
0
1
0
MCLR wake-up reset (from SLEEP)
WDT reset (normal operation)
33k
WDT wake-up reset (from SLEEP)
Q1
10k
MCLR
Legend: u= unchanged
Note 1: The TO and PD bits maintain their status (u) until
a reset occurs. A low-pulse on the MCLR input
does not change the TO and PD status bits.
40k
PIC16C5X
These STATUS bits are only affected by events listed
in Table 7-9.
This circuit will activate reset when VDD goes below Vz +
0.7V (where Vz = Zener voltage).
TABLE 7-9:
EVENTS AFFECTING TO/PD
STATUS BITS
Event
TO PD
Remarks
FIGURE 7-16: BROWN-OUT PROTECTION
CIRCUIT 2
1
0
1
1
1
u
0
1
Power-up
WDT Time-out
No effect on PD
VDD
SLEEPinstruction
CLRWDTinstruction
Legend: u= unchanged
A WDT time-out will occur regardless of the status of the TO
bit. A SLEEPinstruction will be executed, regardless of the
status of the PD bit. Table 7-8 reflects the status of TO and
PD after the corresponding event.
VDD
R1
Q1
MCLR
R2
40k
PIC16C5X
Table 7-5 lists the reset conditions for the special
function registers, while Table 7-6 lists the reset
conditions for all the registers.
This brown-out circuit is less expensive, although
less accurate. Transistor Q1 turns off when VDD
is below a certain level such that:
R1
= 0.7V
VDD •
R1 + R2
1996 Microchip Technology Inc.
DS30236B-page 39
Enhanced PIC16C5X
7.9
Power-Down Mode (SLEEP)
7.10
Program Verification/Code Protection
A device may be powered down (SLEEP) and later
powered up (Wake-up from SLEEP).
If the code protection bit(s) have not been
programmed, the on-chip program memory can be
read out for verification purposes.
7.9.1
SLEEP
Note: Microchip does not recommend code pro-
The Power-Down mode is entered by executing a
tecting windowed devices.
SLEEPinstruction.
7.11
ID Locations
If enabled, the Watchdog Timer will be cleared but
keeps running, the TO bit (STATUS<4>) is set, the PD
bit (STATUS<3>) is cleared and the oscillator driver is
turned off. The I/O ports maintain the status they had
before the SLEEP instruction was executed (driving
high, driving low, or hi-impedance).
Four memory locations are designated as ID locations
where the user can store checksum or other
code-identification numbers. These locations are not
accessible during normal execution but are readable
and writable during program/verify.
It should be noted that a RESET generated by a WDT
time-out does not drive the MCLR/VPP pin low.
Use only the lower 4 bits of the ID locations and
always program the upper 8 bits as '1's.
For lowest current consumption while powered down,
the T0CKI input should be at VDD or VSS and the
MCLR/VPP pin must be at a logic high level (VIHMC).
Note: Microchip will assign a unique pattern
number for QTP and SQTP requests and
for ROM devices. This pattern number will
be unique and traceable to the submitted
code.
7.9.2
WAKE-UP FROM SLEEP
The device can wake up from SLEEP through one of
the following events:
1. An external reset input on MCLR/VPP pin.
2. A Watchdog Timer time-out reset (if WDT was
enabled).
Both of these events cause a device reset. The TO
and PD bits can be used to determine the cause of
device reset. The TO bit is cleared if a WDT time-out
occurred (and caused wake-up). The PD bit, which is
set on power-up, is cleared when SLEEPis invoked.
The WDT is cleared when the device wakes from
sleep, regardless of the wake-up source.
DS30236B-page 40
1996 Microchip Technology Inc.
Enhanced PIC16C5X
All instructions are executed within one single
instruction cycle, unless a conditional test is true or the
program counter is changed as a result of an
instruction. In this case, the execution takes two
instruction cycles. One instruction cycle consists of
four oscillator periods. Thus, for an oscillator
frequency of 4 MHz, the normal instruction execution
time is 1 µs. If a conditional test is true or the program
counter is changed as a result of an instruction, the
instruction execution time is 2 µs.
8.0
INSTRUCTION SET SUMMARY
Each PIC16C5X instruction is a 12-bit word divided
into an OPCODE, which specifies the instruction type,
and one or more operands which further specify the
operation of the instruction. The PIC16C5X instruction
set summary in Table 8-2 groups the instructions into
byte-oriented, bit-oriented, and literal and control
operations. Table 8-1 shows the opcode field
descriptions.
For byte-oriented instructions, 'f' represents a file
register designator and 'd' represents a destination
designator. The file register designator is used to
specify which one of the 32 file registers is to be used
by the instruction.
Figure 8-1 shows the three general formats that the
instructions can have. All examples in the figure use the
following format to represent a hexadecimal number:
0xhhh
where 'h' signifies a hexadecimal digit.
The destination designator specifies where the result
of the operation is to be placed. If 'd' is '0', the result is
placed in the W register. If 'd' is '1', the result is placed
in the file register specified in the instruction.
FIGURE 8-1: GENERAL FORMAT FOR
INSTRUCTIONS
Byte-oriented file register operations
For bit-oriented instructions, 'b' represents a bit field
designator which selects the number of the bit affected
by the operation, while 'f' represents the number of the
file in which the bit is located.
11
6
5
d
4
0
OPCODE
f (FILE #)
d = 0 for destination W
d = 1 for destination f
For literal and control operations, 'k' represents an
8 or 9-bit constant or literal value.
f = 5-bit file register address
Bit-oriented file register operations
11 8 7
b (BIT #)
TABLE 8-1:
OPCODE FIELD
DESCRIPTIONS
5
4
0
OPCODE
f (FILE #)
Field
Description
b = 3-bit bit address
f = 5-bit file register address
f
W
b
k
Register file address (0x00 to 0x7F)
Working register (accumulator)
Literal and control operations (except GOTO)
11
Bit address within an 8-bit file register
Literal field, constant data or label
8
7
0
OPCODE
k (literal)
Don't care location (= 0 or 1)
k = 8-bit immediate value
Literal and control operations - GOTOinstruction
11 0
The assembler will generate code with x = 0. It is
the recommended form of use for compatibility
with all Microchip software tools.
x
d
9
8
Destination select;
OPCODE
k (literal)
d = 0 (store result in W)
d = 1 (store result in file register 'f')
Default is d = 1
k = 9-bit immediate value
label Label name
TOS
PC
Top of Stack
Program Counter
Watchdog Timer Counter
Time-Out bit
WDT
TO
PD
Power-Down bit
Destination, either the W register or the specified
register file location
dest
Options
[ ]
( )
→
Contents
Assigned to
Register bit field
In the set of
< >
User defined term (font is courier)
italics
1996 Microchip Technology Inc.
DS30236B-page 41
Enhanced PIC16C5X
TABLE 8-2:
INSTRUCTION SET SUMMARY
12-Bit Opcode
Cycles MSb LSb Affected Notes
Mnemonic,
Operands
Status
Description
0001 11df ffff
C,DC,Z
1,2,4
2,4
4
1
1
1
1
1
1
Add W and f
AND W with f
Clear f
Clear W
Complement f
Decrement f
Decrement f, Skip if 0
Increment f
Increment f, Skip if 0
Inclusive OR W with f
Move f
Move W to f
No Operation
Rotate left f through Carry
Rotate right f through Carry
Subtract W from f
Swap f
ADDWF
ANDWF
CLRF
CLRW
COMF
DECF
DECFSZ
INCF
INCFSZ
IORWF
MOVF
MOVWF
NOP
f,d
f,d
f
0001 01df ffff
0000 011f ffff
0000 0100 0000
0010 01df ffff
0000 11df ffff
Z
Z
Z
Z
Z
None
Z
None
Z
–
f, d
f, d
f, d
f, d
f, d
f, d
f, d
f
2,4
2,4
2,4
2,4
2,4
2,4
1,4
1(2) 0010 11df ffff
0010 10df ffff
1(2) 0011 11df ffff
1
1
1
1
1
1
1
1
1
1
0001 00df ffff
0010 00df ffff
0000 001f ffff
0000 0000 0000
0011 01df ffff
0011 00df ffff
0000 10df ffff
0011 10df ffff
0001 10df ffff
Z
None
None
C
–
2,4
2,4
1,2,4
2,4
RLF
RRF
SUBWF
SWAPF
XORWF
f, d
f, d
f, d
f, d
f, d
C
C,DC,Z
None
Z
2,4
Exclusive OR W with f
BIT-ORIENTED FILE REGISTER OPERATIONS
1
1
0100 bbbf ffff
0101 bbbf ffff
None
None
None
None
2,4
2,4
Bit Clear f
Bit Set f
Bit Test f, Skip if Clear
Bit Test f, Skip if Set
BCF
BSF
BTFSC
BTFSS
f, b
f, b
f, b
f, b
1 (2) 0110 bbbf ffff
1 (2) 0111 bbbf ffff
LITERAL AND CONTROL OPERATIONS
1
2
1
2
1
1
1
2
1
1
1
1110 kkkk kkkk
1001 kkkk kkkk
0000 0000 0100
101k kkkk kkkk
1101 kkkk kkkk
1100 kkkk kkkk
0000 0000 0010
1000 kkkk kkkk
0000 0000 0011
0000 0000 0fff
1111 kkkk kkkk
Z
None
O, PD
None
Z
None
None
None
TO, PD
None
Z
AND literal with W
Call subroutine
ANDLW
CALL
CLRWDT
GOTO
IORLW
MOVLW
OPTION
RETLW
SLEEP
TRIS
k
k
k
k
k
k
k
k
–
f
1
3
T
Clear Watchdog Timer
Unconditional branch
Inclusive OR Literal with W
Move Literal to W
Load OPTION register
Return, place Literal in W
Go into standby mode
Load TRIS register
Exclusive OR Literal to W
XORLW
k
Note 1: The 9th bit of the program counter will be forced to a '0' by any instruction that writes to the PC except forGOTO.
(Section 4.5)
2: When an I/O register is modified as a function of itself (e.g.MOVF PORTB, 1), the value used will be that value
present on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven
low by an external device, the data will be written back with a '0'.
3: The instruction TRIS f, where f = 5, 6, or 7 causes the contents of the W register to be written to the tristate
latches of PORTA, B or C, respectively. A '1' forces the pin to a hi-impedance state and disables the output buff-
ers.
4: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared
(if assigned to TMR0).
DS30236B-page 42
1996 Microchip Technology Inc.
Enhanced PIC16C5X
ADDWF
Syntax:
Add W and f
[ label ] ADDWF f,d
0 ≤ f ≤ 31
ANDWF
Syntax:
AND W with f
[ label ] ANDWF f,d
0 ≤ f ≤ 31
Operands:
Operands:
d
[0,1]
d
[0,1]
Operation:
(W) + (f) → (dest)
Operation:
(W) .AND. (f) → (dest)
Status Affected: C, DC, Z
Status Affected:
Encoding:
Z
0001
11df
ffff
0001
01df
ffff
Encoding:
Add the contents of the W register and
register 'f'. If 'd' is 0 the result is stored
in the W register. If 'd' is '1' the result is
stored back in register 'f'.
The contents of the W register are
AND’ed with register 'f'. If 'd' is 0 the
result is stored in the W register. If 'd' is
'1' the result is stored back in register 'f'.
Description:
Description:
Words:
1
Words:
1
1
Cycles:
Example:
1
Cycles:
Example:
ADDWF FSR, 0
ANDWF FSR,
1
Before Instruction
Before Instruction
W
=
0x17
W
=
0x17
FSR = 0xC2
FSR = 0xC2
After Instruction
After Instruction
W
=
0xD9
W
=
0x17
FSR = 0xC2
FSR = 0x02
ANDLW
And literal with W
BCF
Bit Clear f
Syntax:
[ label ] ANDLW
k
Syntax:
Operands:
[ label ] BCF f,b
Operands:
Operation:
Status Affected:
Encoding:
Description:
0 ≤ k ≤ 255
0 ≤ f ≤ 31
0 ≤ b ≤ 7
(W).AND. (k) → (W)
Operation:
0 → (f<b>)
Z
Status Affected: None
1110
kkkk
kkkk
0100
bbbf
ffff
Encoding:
Description:
Words:
The contents of the W register are
AND’ed with the eight-bit literal 'k'. The
result is placed in the W register.
Bit 'b' in register 'f' is cleared.
1
1
Words:
1
Cycles:
Cycles:
Example:
1
BCF
FLAG_REG,
7
Example:
ANDLW 0x5F
Before Instruction
Before Instruction
FLAG_REG = 0xC7
W
=
0xA3
After Instruction
After Instruction
FLAG_REG = 0x47
W
=
0x03
1996 Microchip Technology Inc.
DS30236B-page 43
Enhanced PIC16C5X
BSF
Bit Set f
BTFSS
Bit Test f, Skip if Set
Syntax:
Operands:
[ label ] BSF f,b
Syntax:
[ label ] BTFSS f,b
0 ≤ f ≤ 31
0 ≤ b ≤ 7
Operands:
0 ≤ f ≤ 31
0 ≤ b < 7
Operation:
1 → (f<b>)
Operation:
skip if (f<b>) = 1
Status Affected: None
Status Affected: None
0101
bbbf
ffff
0111
bbbf
ffff
Encoding:
Description:
Words:
Encoding:
Bit 'b' in register 'f' is set.
If bit 'b' in register 'f' is '1' then the next
instruction is skipped.
Description:
1
1
If bit 'b' is '1', then the next instruction
fetched during the current instruction
execution, is discarded and an NOP is
executed instead, making this a 2 cycle
instruction.
Cycles:
BSF
FLAG_REG,
7
Example:
Before Instruction
FLAG_REG = 0x0A
Words:
1
After Instruction
Cycles:
Example:
1(2)
FLAG_REG = 0x8A
HERE
FALSE GOTO
TRUE
BTFSS FLAG,1
PROCESS_CODE
•
BTFSC
Bit Test f, Skip if Clear
•
•
Syntax:
[ label ] BTFSC f,b
Operands:
0 ≤ f ≤ 31
0 ≤ b ≤ 7
Before Instruction
PC
=
address (HERE)
After Instruction
If FLAG<1>
PC
Operation:
skip if (f<b>) = 0
=
=
=
=
0,
Status Affected: None
address (FALSE);
1,
address (TRUE)
bbbf
ffff
if FLAG<1>
PC
Encoding:
0110
If bit 'b' in register 'f' is 0 then the next
instruction is skipped.
Description:
If bit 'b' is 0 then the next instruction
fetched during the current instruction
execution is discarded, and an NOP is
executed instead, making this a 2 cycle
instruction.
Words:
1
Cycles:
Example:
1(2)
HERE
FALSE GOTO
TRUE
BTFSC
FLAG,1
PROCESS_CODE
•
•
•
Before Instruction
PC
=
address (HERE)
After Instruction
if FLAG<1>
PC
=
=
=
=
0,
address (TRUE);
1,
address(FALSE)
if FLAG<1>
PC
DS30236B-page 44
1996 Microchip Technology Inc.
Enhanced PIC16C5X
CALL
Subroutine Call
[ label ] CALL k
0 ≤ k ≤ 255
CLRW
Clear W
Syntax:
Syntax:
[ label ] CLRW
None
Operands:
Operation:
Operands:
Operation:
(PC) + 1→ Top of Stack;
k → PC<7:0>;
00h → (W);
1 → Z
(STATUS<6:5>) → PC<10:9>;
0 → PC<8>
Status Affected:
Encoding:
Z
0000
0100
0000
Status Affected: None
The W register is cleared. Zero bit (Z)
is set.
Description:
1001
kkkk
kkkk
Encoding:
Subroutine call. First, return address
(PC+1) is pushed onto the stack. The
eight bit immediate address is loaded
into PC bits <7:0>. The upper bits
PC<10:9> are loaded from STA-
TUS<6:5>, PC<8> is cleared. CALLis
a two cycle instruction.
Description:
Words:
1
Cycles:
Example:
1
CLRW
Before Instruction
W
=
0x5A
After Instruction
Words:
1
2
W
=
0x00
Cycles:
Example:
Z
=
1
HERE
CALL
THERE
Before Instruction
CLRWDT
Clear Watchdog Timer
[ label ] CLRWDT
None
PC
=
address (HERE)
Syntax:
After Instruction
PC
=
address (THERE)
Operands:
Operation:
TOS =
address (HERE + 1)
00h → WDT;
0 → WDT prescaler (if assigned);
1 → TO;
1 → PD
CLRF
Clear f
Syntax:
[ label ] CLRF
f
Status Affected: TO, PD
Operands:
Operation:
0 ≤ f ≤ 31
0000
0000
0100
Encoding:
00h → (f);
1 → Z
The CLRWDTinstruction resets the
WDT. It also resets the prescaler, if the
prescaler is assigned to the WDT and
not Timer0. Status bits TO and PD are
set.
Description:
Status Affected:
Encoding:
Z
0000
011f
ffff
The contents of register 'f' are cleared
and the Z bit is set.
Description:
Words:
1
Cycles:
Example:
1
Words:
1
1
CLRWDT
Cycles:
Example:
Before Instruction
CLRF
FLAG_REG
WDT counter
=
=
?
Before Instruction
FLAG_REG
After Instruction
WDT counter
=
0x5A
0x00
After Instruction
WDT prescale =
0
1
1
FLAG_REG
Z
=
=
0x00
1
TO
PD
=
=
1996 Microchip Technology Inc.
DS30236B-page 45
Enhanced PIC16C5X
COMF
Complement f
[ label ] COMF f,d
0 ≤ f ≤ 31
DECFSZ
Syntax:
Decrement f, Skip if 0
[ label ] DECFSZ f,d
0 ≤ f ≤ 31
Syntax:
Operands:
Operands:
d
[0,1]
d
[0,1]
Operation:
(f) → (dest)
Operation:
(f) – 1 → d; skip if result = 0
Status Affected:
Encoding:
Z
Status Affected: None
0010
01df
ffff
0010
11df
ffff
Encoding:
The contents of register 'f' are comple-
mented. If 'd' is 0 the result is stored in
the W register. If 'd' is 1 the result is
stored back in register 'f'.
The contents of register 'f' are decre-
mented. If 'd' is 0 the result is placed in
the W register. If 'd' is 1 the result is
placed back in register 'f'.
Description:
Description:
If the result is 0, the next instruction,
which is already fetched, is discarded
and an NOP is executed instead mak-
ing it a two cycle instruction.
Words:
1
1
Cycles:
Example:
COMF
REG1,0
Words:
1
Before Instruction
REG1
=
0x13
0x13
Cycles:
Example:
1(2)
After Instruction
HERE
DECFSZ
GOTO
CONTINUE •
CNT, 1
LOOP
REG1
=
W
=
0xEC
•
•
DECF
Decrement f
[ label ] DECF f,d
0 ≤ f ≤ 31
Before Instruction
PC
=
address (HERE)
Syntax:
After Instruction
Operands:
CNT
if CNT
PC
if CNT
PC
=
=
=
≠
=
CNT - 1;
0,
address (CONTINUE);
0,
d
[0,1]
Operation:
(f) – 1 → (dest)
Status Affected:
Encoding:
Z
address (HERE+1)
0000
11df
ffff
Decrement register 'f'. If 'd' is 0 the
result is stored in the W register. If 'd' is
1 the result is stored back in register 'f'.
Description:
GOTO
Unconditional Branch
[ label ] GOTO k
0 ≤ k ≤ 511
Syntax:
Words:
1
1
Operands:
Operation:
Cycles:
Example:
k → PC<8:0>;
STATUS<6:5> → PC<10:9>
DECF
CNT,
1
Before Instruction
Status Affected: None
CNT
=
0x01
0
101k
kkkk
kkkk
Encoding:
Z
=
GOTOis an unconditional branch. The
9-bit immediate value is loaded into PC
bits <8:0>. The upper bits of PC are
loaded from STATUS<6:5>. GOTOis a
two cycle instruction.
Description:
After Instruction
CNT
=
0x00
1
Z
=
Words:
1
Cycles:
Example:
2
GOTO THERE
After Instruction
PC
=
address (THERE)
DS30236B-page 46
1996 Microchip Technology Inc.
Enhanced PIC16C5X
INCF
Increment f
IORLW
Inclusive OR literal with W
[ label ] IORLW k
0 ≤ k ≤ 255
Syntax:
Operands:
[ label ] INCF f,d
Syntax:
0 ≤ f ≤ 31
Operands:
Operation:
Status Affected:
Encoding:
Description:
d
[0,1]
(W) .OR. (k) → (W)
Z
Operation:
(f) + 1 → (dest)
Status Affected:
Encoding:
Z
1101
kkkk
kkkk
0010
10df
ffff
The contents of the W register are
OR’ed with the eight bit literal 'k'. The
result is placed in the W register.
The contents of register 'f' are incre-
mented. If 'd' is 0 the result is placed in
the W register. If 'd' is 1 the result is
placed back in register 'f'.
Description:
Words:
1
Cycles:
Example:
1
Words:
1
1
IORLW 0x35
Cycles:
Example:
Before Instruction
INCF
CNT,
1
W
=
0x9A
Before Instruction
After Instruction
CNT
=
0xFF
0
W
=
0xBF
Z
=
Z
=
0
After Instruction
CNT
Z
=
=
0x00
1
IORWF
Inclusive OR W with f
[ label ] IORWF f,d
0 ≤ f ≤ 31
Syntax:
Operands:
INCFSZ
Increment f, Skip if 0
[ label ] INCFSZ f,d
0 ≤ f ≤ 31
d
[0,1]
Syntax:
Operation:
(W).OR. (f) → (dest)
Operands:
Status Affected:
Encoding:
Z
d
[0,1]
0001
00df
ffff
Operation:
(f) + 1 → (dest), skip if result = 0
Inclusive OR the W register with regis-
ter 'f'. If 'd' is 0 the result is placed in
the W register. If 'd' is 1 the result is
placed back in register 'f'.
Description:
Status Affected: None
0011
11df
ffff
Encoding:
The contents of register 'f' are incre-
mented. If 'd' is 0 the result is placed in
the W register. If 'd' is 1 the result is
placed back in register 'f'.
Description:
Words:
1
1
Cycles:
Example:
If the result is 0, then the next instruc-
tion, which is already fetched, is dis-
carded and an NOP is executed
instead making it a two cycle instruc-
tion.
IORWF
RESULT, 0
Before Instruction
RESULT =
0x13
0x91
W
=
After Instruction
RESULT =
Words:
1
0x13
0x93
0
Cycles:
Example:
1(2)
W
Z
=
=
HERE
INCFSZ
GOTO
CNT,
LOOP
1
CONTINUE •
•
•
Before Instruction
PC
=
address (HERE)
After Instruction
CNT
if CNT
PC
if CNT
PC
=
=
=
≠
=
CNT + 1;
0,
address (CONTINUE);
0,
address (HERE +1)
1996 Microchip Technology Inc.
DS30236B-page 47
Enhanced PIC16C5X
MOVF
Move f
MOVWF
Syntax:
Move W to f
[ label ] MOVWF
0 ≤ f ≤ 31
Syntax:
Operands:
[ label ] MOVF f,d
f
0 ≤ f ≤ 31
Operands:
Operation:
d
[0,1]
(W) → (f)
Operation:
(f) → (dest)
Status Affected: None
Status Affected:
Encoding:
Z
0000
001f
ffff
Encoding:
0010
00df
ffff
Move data from the W register to regis-
ter 'f'.
Description:
The contents of register 'f' is moved to
destination 'd'. If 'd' is 0, destination is
the W register. If 'd' is 1, the destination
is file register 'f'. 'd' is 1 is useful to test
a file register since status flag Z is
affected.
Description:
Words:
1
Cycles:
Example:
1
MOVWF TEMP_REG
Before Instruction
Words:
1
1
TEMP_REG
W
=
=
0xFF
0x4F
Cycles:
Example:
MOVF
FSR,
0
After Instruction
TEMP_REG
W
=
=
0x4F
0x4F
After Instruction
W
=
value in FSR register
NOP
No Operation
[ label ] NOP
None
MOVLW
Move Literal to W
[ label ] MOVLW k
0 ≤ k ≤ 255
Syntax:
Syntax:
Operands:
Operation:
Operands:
Operation:
No operation
k → (W)
Status Affected: None
0000
0000
0000
Status Affected: None
Encoding:
Description:
Words:
1100
kkkk
kkkk
Encoding:
No operation.
The eight bit literal 'k' is loaded into the
W register. The don’t cares will assem-
ble as 0s.
Description:
1
Cycles:
1
NOP
Example:
Words:
1
Cycles:
Example:
1
MOVLW 0x5A
After Instruction
W
=
0x5A
DS30236B-page 48
1996 Microchip Technology Inc.
Enhanced PIC16C5X
OPTION
Syntax:
Load OPTION Register
[ label ] OPTION
None
RLF
Rotate Left f through Carry
[ label ] RLF f,d
0 ≤ f ≤ 31
Syntax:
Operands:
Operands:
Operation:
d
[0,1]
(W) → OPTION
Status Affected: None
Operation:
See description below
C
0000
0000
0010
Encoding:
Status Affected:
Encoding:
The content of the W register is loaded
into the OPTION register.
Description:
0011
01df
ffff
The contents of register 'f' are rotated
one bit to the left through the Carry
Flag. If 'd' is 0 the result is placed in the
W register. If 'd' is 1 the result is stored
back in register 'f'.
Description:
Words:
Cycles:
Example
1
1
OPTION
Before Instruction
register 'f'
C
W
=
0x07
0x07
After Instruction
OPTION =
Words:
1
Cycles:
Example:
1
RLF
REG1,0
RETLW
Return with Literal in W
[ label ] RETLW k
0 ≤ k ≤ 255
Before Instruction
Syntax:
REG1
C
=
=
1110 0110
0
Operands:
Operation:
After Instruction
k → (W);
TOS → PC
REG1
W
C
=
=
=
1110 0110
1100 1100
1
Status Affected: None
1000
kkkk
kkkk
Encoding:
The W register is loaded with the eight
bit literal 'k'. The program counter is
loaded from the top of the stack (the
return address). This is a two cycle
instruction.
Description:
RRF
Rotate Right f through Carry
[ label ] RRF f,d
0 ≤ f ≤ 31
Syntax:
Operands:
d
[0,1]
Words:
1
2
Operation:
See description below
C
Cycles:
Example:
Status Affected:
Encoding:
CALL TABLE ;W contains
;table offset
;value.
0011
00df
ffff
The contents of register 'f' are rotated
one bit to the right through the Carry
Flag. If 'd' is 0 the result is placed in the
W register. If 'd' is 1 the result is placed
back in register 'f'.
Description:
•
•
;W now has table
;value.
•
TABLE
ADDWF PC
RETLW k1
RETLW k2
;W = offset
;Begin table
;
register 'f'
C
•
•
Words:
1
•
Cycles:
Example:
1
RETLW kn
; End of table
RRF
REG1,0
Before Instruction
W
=
0x07
Before Instruction
REG1
C
=
=
1110 0110
0
After Instruction
W
=
value of k8
After Instruction
REG1
W
C
=
=
=
1110 0110
0111 0011
0
1996 Microchip Technology Inc.
DS30236B-page 49
Enhanced PIC16C5X
SLEEP
Enter SLEEP Mode
SUBWF
Subtract W from f
Syntax:
Syntax:
[label]
[label] SUBWF f,d
SLEEP
Operands:
0 ≤ f ≤ 31
Operands:
Operation:
None
d
[0,1]
00h → WDT;
0 → WDT prescaler;
1 → TO;
Operation:
(f) – (W) → (dest)
Status Affected: C, DC, Z
0 → PD
0000
10df
ffff
Encoding:
Status Affected: TO, PD
Subtract (2’s complement method) the
W register from register 'f'. If 'd' is 0 the
result is stored in the W register. If 'd' is
1 the result is stored back in register 'f'.
Description:
0000
0000
0011
Encoding:
Time-out status bit (TO) is set. The
power down status bit (PD) is cleared.
The WDT and its prescaler are
cleared.
Description:
Words:
1
1
Cycles:
The processor is put into SLEEP mode
with the oscillator stopped. See sec-
tion on SLEEP for more details.
SUBWF
REG1, 1
Example 1:
Before Instruction
Words:
1
REG1
W
C
=
=
=
3
2
?
Cycles:
Example:
1
SLEEP
After Instruction
REG1
W
C
=
=
=
1
2
1
; result is positive
Example 2:
Before Instruction
REG1
W
C
=
=
=
2
2
?
After Instruction
REG1
W
C
=
=
=
0
2
1
; result is zero
Example 3:
Before Instruction
REG1
W
C
=
=
=
1
2
?
After Instruction
REG1
W
C
=
=
=
FF
2
0
; result is negative
DS30236B-page 50
1996 Microchip Technology Inc.
Enhanced PIC16C5X
SWAPF
Syntax:
Swap Nibbles in f
[ label ] SWAPF f,d
0 ≤ f ≤ 31
XORLW
Exclusive OR literal with W
Syntax:
[label] XORLW k
0 ≤ k ≤ 255
Operands:
Operands:
d
[0,1]
Operation:
(W) .XOR. k → (W)
Z
Operation:
(f<3:0>) → (dest<7:4>);
(f<7:4>) → (dest<3:0>)
Status Affected:
Encoding:
1111
kkkk
kkkk
Status Affected: None
The contents of the W register are
XOR’ed with the eight bit literal 'k'. The
result is placed in the W register.
Description:
0011
10df
ffff
Encoding:
The upper and lower nibbles of register
'f' are exchanged. If 'd' is 0 the result is
placed in W register. If 'd' is 1 the result
is placed in register 'f'.
Description:
Words:
1
Cycles:
Example:
1
Words:
Cycles:
Example
1
1
XORLW 0xAF
Before Instruction
W
=
0xB5
SWAPF
REG1,
0
After Instruction
Before Instruction
W
=
0x1A
REG1
=
0xA5
After Instruction
REG1
W
=
=
0xA5
0X5A
XORWF
Exclusive OR W with f
[ label ] XORWF f,d
0 ≤ f ≤ 31
Syntax:
Operands:
TRIS
Load TRIS Register
d
[0,1]
Syntax:
[ label ] TRIS
f = 5, 6 or 7
f
Operation:
(W) .XOR. (f) → (dest)
Operands:
Operation:
Status Affected:
Encoding:
Z
(W) → TRIS register f
0001
10df
ffff
Status Affected: None
Exclusive OR the contents of the W
register with register 'f'. If 'd' is 0 the
result is stored in the W register. If 'd' is
1 the result is stored back in register 'f'.
Description:
0000
0000
0fff
Encoding:
TRIS register 'f' (f = 5, 6, or 7) is loaded
with the contents of the W register
Description:
Words:
Cycles:
Example
1
1
Words:
Cycles:
Example
1
1
TRIS
PORTA
REG,1
XORWF
Before Instruction
Before Instruction
W
=
0XA5
0XA5
REG
=
0xAF
0xB5
W
=
After Instruction
TRISA
=
After Instruction
REG
W
=
=
0x1A
0xB5
1996 Microchip Technology Inc.
DS30236B-page 51
Enhanced PIC16C5X
NOTES:
DS30236B-page 52
1996 Microchip Technology Inc.
Enhanced PIC16C5X
The PICMASTER Emulator System has been
designed as a real-time emulation system with
advanced features that are generally found on more
expensive development tools. The PC compatible 386
9.0
DEVELOPMENT SUPPORT
9.1
Development Tools
The PIC16/17 microcontrollers are supported with a full
range of hardware and software development tools:
(and
better)
machine
platform
and
Microsoft Windows 3.x environment was chosen to
best make these features available to you, the
end user.
• PICMASTER Real-Time In-Circuit Emulator
• PRO MATE Universal Programmer
• PICSTART Low-Cost Prototype Programmer
• PICDEM-1 Low-Cost Demonstration Board
• PICDEM-2 Low-Cost Demonstration Board
• MPASM Assembler
The PICMASTER Universal Emulator System consists
primarily of four major components:
• Host-Interface Card
• Emulator Control Pod
• Target-Specific Emulator Probe
• PC-Host Emulation Control Software
• MPSIM Software Simulator
• C Compiler (MP-C)
• Fuzzy logic development system
(fuzzyTECH −MP)
The Windows operating system allows the developer to
take full advantage of the many powerful features and
functions of the PICMASTER system.
9.2
PICMASTER High Performance
Universal In-Circuit Emulator with
MPLAB IDE
PICMASTER emulation can operate in one window,
while a text editor is running in a second window.
PC-Host Emulation Control software takes full advan-
tage of Dynamic Data Exchange (DDE), a feature of
Windows. DDE allows data to be dynamically trans-
ferred between two or more Windows programs. With
this feature, data collected with PICMASTER can be
automatically transferred to a spreadsheet or database
program for further analysis.
The PICMASTER Universal In-Circuit Emulator is
intended to provide the product development engineer
with a complete microcontroller design tool set for all
microcontrollers in the PIC16C5X, PIC16CXX and
PIC17CXX families. PICMASTER is supplied with the
MPLAB Integrated Development Environment (IDE),
which allows editing, "make" and download, and
source debugging from a single environment. A
PICMASTER System configuration is shown
in Figure 9-1.
Under Windows, as many as four PICMASTER emula-
tors can be run simultaneously from the same PC mak-
ing development of multi-microcontroller systems
possible (e.g., a system containing a PIC16CXX
processor and a PIC17CXX processor).
Interchangeable target probes allow the system to be
easily reconfigured for emulation of different proces-
sors. The universal architecture of the PICMASTER
allows expansion to support all new PIC16C5X,
PIC16CXX and PIC17CXX microcontrollers.
The PICMASTER probes specifications are shown
in Table 9-1.
FIGURE 9-1: PICMASTER SYSTEM CONFIGURATION
In-Line
5 VDC
Power Supply
(Optional)
90 - 250 VAC
Windows 3.x
Power Switch
Interchangeable
Emulator Probe
Power Connector
PC Bus
PC-Interface
PICMASTER Emulator Pod
Common Interface Card
PC Compatible Computer
Logic Probes
1996 Microchip Technology Inc.
DS30236B-page 53
Enhanced PIC16C5X
TABLE 9-1:
PICMASTER PROBE
TABLE 9-1:
PICMASTER PROBE
PROBE
PROBE
PICMASTER
PROBE
PICMASTER
PROBE
Devices
Devices
Maximum Operating
Maximum Operating
Frequency
4 MHz
Voltage
Frequency
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
20 MHz
20 MHz
20 MHz
Voltage
(1)
PIC16C52
PROBE-16D
PROBE-16D
PROBE-16D
PROBE-16D
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
PIC16CR64
PIC16C65
PIC16C65A
PIC16C620
PIC16C621
PIC16C622
PIC16C70
PIC16C71
PIC16C71A
PIC16C72
PIC16C73
PIC16C73A
PIC16C74
PIC16C74A
PIC16C83
PIC16C84
PIC17C42
PIC17C43
PIC17C44
PROBE-16E
PROBE-16F
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
4.5V - 5.5V
PIC16C54
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
20 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
10 MHz
(1)
PIC16C54A
PIC16CR54
PIC16CR54A
PIC16CR54B
PIC16C55
PROBE-16F
PROBE-16H
PROBE-16H
PROBE-16H
(1)
PROBE-16D
PROBE-16D
(1)
(1)
PROBE-16D
PROBE-16B
PROBE-16B
(1)
PIC16CR55
PIC16C56
PROBE-16D
PROBE-16D
(1)
PROBE-16B
PROBE-16F
(1)
(1)
PIC16CR56
PIC16C57
PROBE-16D
PROBE-16D
PROBE-16D
PROBE-16F
(1)
PIC16CR57A
PIC16CR57B
PIC16C58A
PIC16CR58A
PIC16CR58B
PIC16C61
PROBE-16F
PROBE-16F
(1)
PROBE-16D
PROBE-16D
PROBE-16D
(1)
PROBE-16F
PROBE-16C
PROBE-16C
PROBE-17B
PROBE-17B
PROBE-17B
(1)
PROBE-16D
PROBE-16G
PROBE-16E
PIC16C62
(1)
PIC16C62A
PIC16CR62
PIC16C63
PROBE-16E
PROBE-16E
PROBE-16F
(1)
(1)
Note 1: This PICMASTER probe can be used to
functionally emulate the device listed in the
previous column. Contact your Microchip sales
office for details.
PIC16C64
PROBE-16E
(1)
PIC16C64A
PROBE-16E
DS30236B-page 54
1996 Microchip Technology Inc.
Enhanced PIC16C5X
9.3
PRO MATE Universal Programmer
9.5
PICDEM-1 Low-Cost PIC16/17
Demonstration Board
The PRO MATE Universal Programmer is
a
full-featured programmer capable of operating in
stand-alone mode as well as PC-hosted mode.
The PICDEM-1 is a simple board which demonstrates
the capabilities of several of Microchip’s
microcontrollers. The microcontrollers supported are:
PIC16C5X (PIC16C54 to PIC16C58A), PIC16C61,
PIC16C62X, PIC16C71, PIC16C8X, PIC17C42,
PIC17C43 and PIC17C44. All necessary hardware and
software is included to run basic demo programs. The
users can program the sample microcontrollers
The PRO MATE has programmable VDD and VPP
supplies which allows it to verify programmed memory
at VDD min and VDD max for maximum reliability. It has
an LCD display for displaying error messages, keys to
enter commands and a modular detachable socket
assembly to support various package types. In stand-
alone mode the PRO MATE can read, verify or program
PIC16C5X, PIC16CXX and PIC17CXX devices. It can
also set configuration and code-protect bits in
this mode.
provided with the PICDEM-1 board, on
a
PRO MATE or PICSTART-16B programmer, and
easily test firmware. The user can also connect the
PICDEM-1 board to the PICMASTER emulator and
download the firmware to the emulator for testing.
Additional prototype area is available for the user to
build some additional hardware and connect it to the
microcontroller socket(s). Some of the features include
an RS-232 interface, a potentiometer for simulated
analog input, push-button switches and eight LEDs
connected to PORTB.
In PC-hosted mode, the PRO MATE connects to the
PC via one of the COM (RS-232) ports. PC based
user-interface software makes using the programmer
simple and efficient. The user interface is full-screen
and menu-based. Full screen display and editing of
data, easy selection of bit configuration and part type,
easy selection of VDD min, VDD max and VPP levels,
load and store to and from disk files (Intel hex format)
are some of the features of the software. Essential
commands such as read, verify, program and blank
check can be issued from the screen. Additionally,
serial programming support is possible where each
part is programmed with a different serial number,
sequential or random.
9.6
PICDEM-2 Low-Cost PIC16CXX
Demonstration Board
The PICDEM-2 is a simple demonstration board that
supports the PIC16C64, PIC16C65, PIC16C73 and
PIC16C74 microcontrollers. All the necessary
hardware and software is included to run the basic
demonstration programs. The user can program
the sample microcontrollers provided with the
PICDEM-2 board, on a PRO MATE programmer or
PICSTART-16C, and easily test firmware. The
PICMASTER emulator may also be used with the
PICDEM-2 board to test firmware. Additional prototype
area has been provided to the user for adding
additional hardware and connecting it to the
microcontroller socket(s). Some of the features include
The PRO MATE has a modular “programming socket
module”. Different socket modules are required for
different processor types and/or package types.
PRO MATE supports all PIC16C5X, PIC16CXX and
PIC17CXX processors.
9.4
PICSTART Low-Cost Development
System
a
RS-232 interface, push-button switches,
a
The PICSTART programmer is an easy to use, very
low-cost prototype programmer. It connects to the PC
via one of the COM (RS-232) ports. A PC-based user
interface software makes using the programmer simple
and efficient. The user interface is full-screen and
menu-based. PICSTART is not recommended for
production programming.
potentiometer for simulated analog input, a Serial
EEPROM to demonstrate usage of the I C bus and
separate headers for connection to an LCD module
and a keypad.
2
1996 Microchip Technology Inc.
DS30236B-page 55
Enhanced PIC16C5X
9.7
MPLAB Integrated Development
Environment Software
9.8
MPASM Assembler
The MPASM CrossAssembler is a PC-hosted symbolic
assembler. It supports all microcontroller series
including the PIC16C5X, PIC16CXX, and PIC17CXX
families.
The MPLAB Software brings an ease of software
development previously unseen in the 8-bit
microcontroller market. MPLAB is a windows based
application which contains:
MPASM offers full featured Macro capabilities,
conditional assembly, and several source and listing
formats. It generates various object code formats to
support Microchip's development tools as well as third
party programmers.
• A full featured editor
• Three operating modes
- editor
- emulator
- simulator (available soon)
• A project manager
• Customizable tool bar and key mapping
• A status bar with project information
MPASM allows full symbolic debugging from
the
Microchip Universal Emulator System
(PICMASTER).
MPASM has the following features to assist in
developing software for specific use applications.
• Extensive on-line help
MPLAB allows you to:
• Provides translation of Assembler source code to
object code for all Microchip microcontrollers.
• edit your source files (either assembly or "C")
• one touch assemble (or compile) and download to
PIC16/17 tools (automatically updates all project
information)
• debug using:
- source files
- absolute listing file
• transfer data dynamically via DDE (soon to be
replaced by OLE)
• Macro assembly capability
• Produces all the files (Object, Listing, Symbol,
and special) required for symbolic debug with
Microchip’s emulator systems.
• Supports Hex (default), Decimal and Octal
source and listing formats.
MPASM provides a rich directive language to support
programming of the PIC16/17. Directives are helpful in
making the development of your assemble source
code shorter and more maintainable.
• run up to four emulators on the same PC
The ability to use MPLAB with Microchip’s simulator
(available soon) allows a consistent platform and the
ability to easily switch from the low cost simulator to the
full featured emulator with minimal retraining due to
development tools.
• Data Directives are those that control the
allocation of memory and provide a way to refer to
data items symbolically (i.e., by meaningful
names).
• Control Directives control the MPASM listing
display. They allow the specification of titles and
sub-titles, page ejects and other listing control.
This eases the readability of the printed
output file.
• Conditional Directives permit sections of
conditionally assembled code. This is most useful
where additional functionality may wished to be
added depending on the product (less
functionality for the low end product, then for the
high end product). Also this is very helpful in the
debugging of a program.
• Macro Directives control the execution and data
allocation within macro body definitions. This
makes very simple the re-use of functions in a
program as well as between programs.
DS30236B-page 56
1996 Microchip Technology Inc.
Enhanced PIC16C5X
9.9
MPSIM Software Simulator
9.11
fuzzyTECH-MP Fuzzy Logic
Development System
The MPSIM Software Simulator allows code
development in a PC host environment. It allows the
user to simulate the PIC16/17 series microcontrollers
on an instruction level. On any given instruction, the
user may examine or modify any of the data areas or
provide external stimulus to any of the pins. The
input/output radix can be set by the user and the
execution can be performed in; single step, execute
until break, or in a trace mode. MPSIM fully supports
symbolic debugging using MP-C and MPASM. The
Software Simulator offers the low cost flexibility to
develop and debug code outside of the laboratory
environment making it an excellent multi-project
software development tool.
fuzzyTECH-MP fuzzy logic development tool is
available in two versions - a low cost introductory
version, MP Explorer, for designers to gain
comprehensive working knowledge of fuzzy logic
system design; and full-featured version,
a
a
fuzzyTECH-MP, edition for implementing more
complex systems.
Both versions include Microchip’s fuzzyLAB
demonstration board for hands-on experience with
fuzzy logic systems implementation.
9.12
Development Systems
For convenience, the development tools are packaged
into comprehensive systems as listed in Table 9-2.
9.10
MP-C C Compiler
The MP-C Code Development System is a complete 'C'
compiler and integrated development environment for
Microchip’s PIC16/17 family of microcontrollers. The
compiler provides powerful integration capabilities and
ease of use not found with other compilers.
For easier source level debugging, the compiler
provides symbol information that is compatible with the
PICMASTER Universal Emulator memory display
(PICMASTER emulator software versions 1.13
and later).
The MP-C Code Development System is supplied
directly by Byte Craft Limited of Waterloo, Ontario,
Canada. If you have any questions, please contact
your regional Microchip FAE or Microchip technical
support personnel at (602) 786-7627.
TABLE 9-2:
Item
DEVELOPMENT SYSTEM PACKAGES
Name
System Description
1.
2.
3.
PICMASTER System
PICMASTER In-Circuit Emulator, PRO MATE Programmer, Assembler, Soft-
ware Simulator, Samples and your choice of Target Probe.
PICSTART System
PRO MATE System
PICSTART Low-Cost Prototype Programmer, Assembler, Software Simulator
and Samples.
PRO MATE Universal Programmer, full featured stand-alone or PC-hosted
programmer, Assembler, Simulator
1996 Microchip Technology Inc.
DS30236B-page 57
Enhanced PIC16C5X
NOTES:
DS30236B-page 58
1996 Microchip Technology Inc.
PIC16C54A
Enh. PIC16C5X
10.0 ELECTRICAL CHARACTERISTICS - PIC16C54A
†
Absolute Maximum Ratings
Ambient temperature under bias............................................................................................................ .-55˚C to +125˚C
Storage temperature ............................................................................................................................. - 65˚C to +150˚C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
(2)
Voltage on MCLR with respect to VSS ............................................................................................................0 to +14V
Voltage on all other pins with respect to VSS .................................................................................. -0.6V to (VDD + 0.6V)
(1)
Total power dissipation .....................................................................................................................................800 mW
Max. current out of VSS pin ...................................................................................................................................150 mA
Max. current into VDD pin......................................................................................................................................100 mA
Max. current into an input pin (T0CKI only) .....................................................................................................................±500 µA
Input clamp current, IIK (VI < 0 or VI > VDD) .....................................................................................................................±20 mA
Output clamp current, IOK (V0 < 0 or V0 > VDD) ..............................................................................................................±20 mA
Max. output current sunk by any I/O pin .................................................................................................................25 mA
Max. output current sourced by any I/O pin ............................................................................................................20 mA
Max. output current sourced by a single I/O port (PORTA or B) .............................................................................40 mA
Max. output current sunk by a single I/O port (PORTA or B) ..................................................................................50 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
Note 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80mA, may cause latch-up. Thus,
a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR pin rather than pulling
this pin directly to VSS
†
NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1996 Microchip Technology Inc.
DS30236B-page 59
Enh. PIC16C5X
PIC16C54A
TABLE 10-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
OSC
PIC16C54A-04
PIC16C54A-10
PIC16C54A-20
PIC16LC54A-04
PIC16C54A/JW
VDD: 3.0V to 6.25V
IDD: 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
VDD: 3.0V to 6.25V
IDD: 1.7 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 3.0V to 6.25V
IDD: 1.7 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 2.5V to 6.25V
IDD: 0.5 mA typ. at
5.5V
IPD: 0.25 µA typ. at
2.5V WDT dis
VDD: 3.0V to 6.25V
IDD: 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
RC
Freq: 4 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
VDD: 3.0V to 6.25V
IDD: 1.7 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 3.0V to 6.25V
IDD: 1.7 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 2.5V to 6.25V
IDD: 0.5 mA typ. at
5.5V
IPD: 0.25 µA typ. at
2.5V WDT dis
VDD: 3.0V to 6.25V
IDD 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
XT
HS
Freq: 4 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
VDD: 4.5V to 5.5V
IDD: 2.4 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 4.5V to 5.5V
IDD: 8.0 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
VDD: 4.5V to 5.5V
IDD: 16 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
VDD: 4.5V to 5.5V
IDD: 8 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Do not use in
HS mode
Freq: 4.0 MHz max.
Freq: 10 MHz max.
Freq: 20 MHz max.
Freq: 10 MHz max.
VDD: 3.0V to 6.25V
IDD: 14 µA typ. at
32kHz, 3.0V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 2.5V to 6.25V
IDD: 27 µA max. at
32kHz, 2.5V
WDT dis
IPD: 4.0 µA max. at
2.5V WDT dis
VDD: 2.5V to 6.25V
IDD: 27 µA max. at
32kHz, 2.5V
WDT dis
IPD: 4.0 µA max. at
2.5V WDT dis
Do not use in
LP mode
Do not use in
LP mode
LP
Freq: 200 kHz max.
Freq: 200 kHz max.
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30236B-page 60
1996 Microchip Technology Inc.
PIC16C54A
Enh. PIC16C5X
10.1
DC Characteristics: PIC16C54A-04, 10, 20 (Commercial)
PIC16C54A-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym Min Typ
Max Units
Conditions
Supply Voltage
XT, RC and LP options
HS option
VDD
3.0
4.5
6.25
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
VSS
V
V
Device in SLEEP mode
See section on Power-On Reset for details
VDD start voltage to ensure
Power-On Reset
VPOR
VDD rise rate to ensure
Power-On Reset
SVDD
IDD
0.05*
V/ms See section on Power-On Reset for details
(3)
Supply Current
(4)
XT and RC options
1.8
2.4
4.5
14
2.4 mA FOSC = 4.0 MHz, VDD = 5.5V
8.0 mA FOSC = 10 MHz, VDD = 5.5V
HS option
16
mA FOSC = 20 MHz, VDD = 5.5V
µA FOSC = 32 kHz, VDD = 3.0V, WDT disabled
µA FOSC = 32 kHz, VDD = 3.0V, WDT disabled
LP option, Commercial
LP option, Industrial
17
(5)
Power Down Current
IPD
Commercial
4.0
0.25 4.0
5.0
0.3
12
µA VDD = 3.0V, WDT enabled
µA VDD = 3.0V, WDT disabled
µA VDD = 3.0V, WDT enabled
µA VDD = 3.0V, WDT disabled
Industrial
14
5.0
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guid-
ance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 61
Enh. PIC16C5X
PIC16C54A
10.2
DC Characteristics: PIC16C54A-04E, 10E, 20E (Automotive)
DC Characteristics
Power Supply Pins
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (automotive)
(1)
Characteristic
Sym Min Typ
Max Units
Conditions
Supply Voltage
XT and RC options
HS option
VDD
3.5
4.5
5.5
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
VSS
V
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
See section on Power-On Reset for details
VDD rise rate to ensure
Power-On Reset
SVDD
IDD
0.05*
V/ms See section on Power-On Reset for details
(3)
Supply Current
(4)
XT and RC options
1.8
4.8
9.0
3.3 mA FOSC = 4.0 MHz, VDD = 5.5V
HS option
10
20
mA FOSC = 10 MHz, VDD = 5.5V
mA FOSC = 20 MHz, VDD = 5.5V
(5)
Power Down Current
IPD
XT and RC options
5.0
0.8
4.0
22
18
22
18
µA VDD = 3.5V, WDT enabled
µA VDD = 3.5V, WDT disabled
µA VDD = 3.5V, WDT enabled
µA VDD = 3.5V, WDT disabled
HS option
0.25
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guid-
ance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30236B-page 62
1996 Microchip Technology Inc.
PIC16C54A
Enh. PIC16C5X
10.3
DC Characteristics: PIC16LC54A-04 (Commercial)
PIC16LC54A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym Min Typ
Max Units
Conditions
Supply Voltage
VDD
XT, RC and LP options
2.5
6.25
V
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
VSS
Device in SLEEP mode
See section on Power-On Reset for details
VDD start voltage to ensure
Power-On Reset
VPOR
VDD rise rate to ensure
Power-On Reset
SVDD
IDD
0.05*
V/ms See section on Power-On Reset for details
(3)
Supply Current
(4)
XT and RC options
0.5
11
14
mA FOSC = 4.0 MHz, VDD = 5.5V
µA FOSC = 32 kHz, VDD = 2.5V WDT disabled
µA FOSC = 32 kHz, VDD = 2.5V WDT disabled
LP option, Commercial
LP option, Industrial
27
35
(5)
Power Down Current
IPD
Commercial
2.5
0.25 4.0
3.5
0.3
12
µA VDD = 2.5V, WDT enabled
µA VDD = 2.5V, WDT disabled
µA VDD = 2.5V, WDT enabled
µA VDD = 2.5V, WDT disabled
Industrial
14
5.0
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guid-
ance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 63
Enh. PIC16C5X
PIC16C54A
10.4
DC Characteristics: PIC16C54A-04, 10, 20, PIC16LC54A-04 (Commercial),
PIC16C54A-04I, 10I, 20I, PIC16LC54A-04I (Industrial),
PIC16C54A-04E, 10E, 20E (Automotive)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (automotive)
DC Characteristics
All Pins Except
Power Supply Pins
Operating Voltage VDD range is described in Section 10.1, Section 10.2 and
Section 10.3.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
0.2 VDD+1V
2.0
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
For all VDD
(5)
4.0V < VDD ≤ 5.5V
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
-1.0
-5.0
0.5
+1.0
µA VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
+5.0
+3.0
+3.0
µA VPIN = VSS +0.25V
(2)
0.5
0.5
0.5
µA VPIN = VDD
T0CKI
OSC1
-3.0
-3.0
µA VSS ≤ VPIN ≤ VDD
µA VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
VOH
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
Output High Voltage
(3)
I/O ports
VDD-0.7
VDD-0.7
V
V
IOH = -5.4 mA, VDD = 4.5V
IOH = -1.0 mA, VDD = 4.5V,
RC option only
OSC2/CLKOUT
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30236B-page 64
1996 Microchip Technology Inc.
PIC16C54A
Enh. PIC16C5X
10.5
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
T
Time
2
to
mc
osc
os
MCLR
ck
cy
drt
io
CLKOUT
cycle time
device reset timer
I/O port
oscillator
OSC1
t0
T0CKI
wdt
watchdog timer
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
FIGURE 10-1: LOAD CONDITIONS - PIC16C54A
Pin
CL = 50 pF for all pins except OSC2
CL
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
VSS
1996 Microchip Technology Inc.
DS30236B-page 65
Enh. PIC16C5X
PIC16C54A
10.6
Timing Diagrams and Specifications
FIGURE 10-2: EXTERNAL CLOCK TIMING - PIC16C54A
Q4
Q3
Q4
4
Q1
Q1
Q2
OSC1
1
3
3
4
2
CLKOUT
TABLE 10-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C54A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 10.1, Section 10.2 and Section 10.3.
Parameter
No.
(1)
Sym
Characteristic
Min Typ
Max Units
Conditions
(2)
FOSC
External CLKIN Frequency
DC
DC
DC
DC
DC
DC
DC
0.1
4
—
—
—
—
—
—
—
—
—
—
—
—
4.0
4.0
4.0
10
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
4.0
4.0
4.0
10
(2)
Oscillator Frequency
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
4
4
20
5
200
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating condi-
tions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30236B-page 66
1996 Microchip Technology Inc.
PIC16C54A
Enh. PIC16C5X
TABLE 10-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C54A (CON’T)
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 10.1, Section 10.2 and Section 10.3.
Parameter
(1)
No.
Sym
Characteristic
Min Typ
Max Units
Conditions
RC osc mode
(2)
1
TOSC
External CLKIN Period
250
250
250
100
50
—
—
—
—
ns
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
—
ns
ns
µs
ns
ns
ns
XT osc mode
—
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
—
—
5.0
250
250
250
100
50
—
—
(2)
Oscillator Period
—
—
RC osc mode
—
10,000
250
250
250
200
—
XT osc mode
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
5.0
—
—
(3)
2
3
TCY
Instruction Cycle Time
4/FOSC
—
TosL, TosH Clock in (OSC1) Low or High Time
50*
20*
2.0*
—
—
XT oscillator
HS oscillator
LP oscillator
XT oscillator
HS oscillator
LP oscillator
—
—
—
—
4
TosR, TosF Clock in (OSC1) Rise or Fall Time
—
25*
25*
50*
—
—
—
—
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating condi-
tions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1996 Microchip Technology Inc.
DS30236B-page 67
Enh. PIC16C5X
PIC16C54A
FIGURE 10-3: CLKOUT AND I/O TIMING - PIC16C54A
Q1
Q2
Q3
Q4
OSC1
10
11
CLKOUT
13
12
18
14
19
16
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 10-3: CLKOUT AND I/O TIMING REQUIREMENTS - PIC16C54A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 10.1, Section 10.2 and
Section 10.3.
Parameter
(1)
No.
Sym
Characteristic
(2)
Min
Typ
Max
Units
10
11
12
13
14
15
16
17
18
TosH2ckL
TosH2ckH
TckR
OSC1↑ to CLKOUT↓
—
15
15
5.0
5.0
—
30**
30**
15**
15**
40**
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
(2)
OSC1↑ to CLKOUT↑
—
(2)
CLKOUT rise time
—
(2)
TckF
CLKOUT fall time
—
(2)
CLKOUT↓ to Port out valid
TckL2ioV
TioV2ckH
TckH2ioI
TosH2ioV
TosH2ioI
—
(2)
Port in valid before CLKOUT↑
(2)
0.25 TCY+30*
—
Port in hold after CLKOUT↑
OSC1↑ (Q1 cycle) to Port out valid
0*
—
—
—
(3)
—
100*
—
OSC1↑ (Q2 cycle) to Port input invalid (I/O in
TBD
—
hold time)
19
TioV2osH
Port input valid to OSC1↑
TBD
—
—
ns
(I/O in setup time)
(3)
20
21
TioR
TioF
Port output rise time
—
—
10
10
25**
25**
ns
ns
(3)
Port output fall time
*
These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 10-1 for loading conditions.
DS30236B-page 68
1996 Microchip Technology Inc.
PIC16C54A
Enh. PIC16C5X
FIGURE 10-4: RESET, WATCHDOG TIMER, AND
DEVICE RESET TIMER TIMING - PIC16C54A
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 10-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16C54A
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 10.1, Section 10.2 and Section 10.3.
Parameter
No.
(1)
Sym Characteristic
Min Typ
Max Units
Conditions
30
31
TmcL MCLR Pulse Width (low)
100*
9.0*
—
—
ns VDD = 5.0V
Twdt Watchdog Timer Time-out Period
(No Prescaler)
18*
40*
ms VDD = 5.0V (Commercial)
32
34
TDRT Device Reset Timer Period
9.0*
—
18*
—
30*
ms VDD = 5.0V (Commercial)
ns
TioZ I/O Hi-impedance from MCLR Low
100*
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
1996 Microchip Technology Inc.
DS30236B-page 69
Enh. PIC16C5X
PIC16C54A
FIGURE 10-5: TIMER0 CLOCK TIMINGS - PIC16C54A
T0CKI
40
41
42
TABLE 10-5: TIMER0 CLOCK REQUIREMENTS - PIC16C54A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 10.1, Section 10.2 and
Section 10.3.
Parameter
(1)
Sym Characteristic
Min
Typ
Max Units Conditions
No.
40
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
41
42
Tt0L T0CKI Low Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
Tt0P T0CKI Period
20 or TCY + 40*
N
ns Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
DS30236B-page 70
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
11.0 ELECTRICAL CHARACTERISTICS - PIC16CR54A
Absolute Maximum Ratings†
Ambient Temperature under bias...........................................................................................................–55°C to +125°C
Storage Temperature .............................................................................................................................–65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
(2)
Voltage on MCLR with respect to VSS ............................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
(1)
Total Power Dissipation ....................................................................................................................................800 mW
Max. Current out of VSS pin ..................................................................................................................................150 mA
Max. Current into VDD pin .......................................................................................................................................50 mA
Max. Current into an input pin (T0CKI only) ....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD)....................................................................................................................±20 mA
Output Clamp Current, IOK (V0 < 0 or V0 > VDD).............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin................................................................................................................25 mA
Max. Output Current sourced by any I/O pin...........................................................................................................20 mA
Max. Output Current sourced by a single I/O port (PORTA or B)............................................................................40 mA
Max. Output Current sunk by a single I/O port (PORTA or B).................................................................................50 mA
Note 1: Power Dissipation is calculated as follows: PDIS = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
Note 2: Voltage spikes below Vss at the MCLR pin, inducing currents greater than 80 mA may cause latch-up. Thus,
a series resistor of 50 to 100Ω should be used when applying a low level to the MCLR pin rather than pulling
this pin directly to Vss.
†
NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1996 Microchip Technology Inc.
DS30236B-page 71
Enh. PIC16C5X
PIC16CR54A
TABLE 11-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
OSC
PIC16CR54A-04
PIC16CR54A-10
PIC16CR54A-20
PIC16LCR54A-04
RC
VDD: 2.5 V to 6.25 V
IDD: 3.6 mA max at 6.0 V
IPD: 6.0 µA max at 2.5 V,
WDT dis
N/A
N/A
N/A
Freq: 4 MHz max
XT
HS
LP
VDD: 2.5 V to 6.25 V
IDD: 3.6 mA max at 6.0 V
IPD: 6.0 µA max at 2.5 V,
WDT dis
N/A
N/A
N/A
N/A
Freq: 4.0 MHz max
VDD: 4.5 V to 5.5 V
IDD: 10 mA max at 5.5 V
IPD: 6.0 µA max at 2.5 V,
WDT dis
VDD: 4.5 V to 5.5 V
IDD: 10 mA max at 5.5 V
IPD: 6.0 µA max at 2.5 V,
WDT dis
N/A
N/A
Freq: 10 MHz max
Freq: 20 MHz max
VDD: 2.0 V to 6.25 V
IDD: 20 µA max at 32 kHz,
2.0 V
IPD: 6.0 µA max at 2.5 V,
WDT dis
N/A
N/A
Freq: 200 kHz max
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30236B-page 72
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
11.1
DC Characteristics: PIC16CR54A-04, 10, 20 (Commercial)
PIC16CR54A-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym
Min Typ
Max
Units
Conditions
Supply Voltage
RC and XT options
HS option
VDD
2.5
4.5
6.25
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
V
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
(4)
RC and XT options
2.0
0.8
90
4.8
9.0
3.6
1.8
350
10
mA
mA
µA
FOSC = 4.0 MHz, VDD = 6.0V
FOSC = 4.0 MHz, VDD = 3.0V
FOSC = 200 kHz, VDD = 2.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
HS option
mA
mA
20
(5)
Power-Down Current
Commercial
IPD
IPD
1.0
2.0
3.0
5.0
6.0
8.0*
15
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 6.0V, WDT disabled
VDD = 6.0V, WDT enabled
25
(5)
Power-Down Current
Industrial
1.0
2.0
3.0
3.0
5.0
8.0
10*
20*
18
µA
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 4.0V, WDT enabled
VDD = 6.0V, WDT disabled
VDD = 6.0V, WDT enabled
45
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 73
Enh. PIC16C5X
PIC16CR54A
11.2
DC Characteristics: PIC16CR54A-04E, 10E, 20E (Automotive)
DC Characteristics
Power Supply Pins
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (automotive)
(1)
Characteristic
Sym
Min Typ
Max Units
Conditions
Supply Voltage
RC and XT options
HS options
VDD
3.25
4.5
6.0
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
V
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
(4)
RC and XT options
1.8
4.8
9.0
3.3
10
20
mA
mA
mA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 16 MHz, VDD = 5.5V
HS option
(5)
Power-Down Current
IPD
5.0
0.8
22
18
µA
µA
VDD = 3.25V, WDT enabled
VDD = 3.25V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design
guidance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30236B-page 74
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
11.3
DC Characteristics: PIC16LCR54A-04 (Commercial)
PIC16LCR54A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym
Min Typ
Max
Units
Conditions
Supply Voltage
VDD
VDR
2.0
6.25
V
V
V
(2)
RAM Data Retention Voltage
1.5*
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
10
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
20
70
µA
µA
FOSC = 32 kHz, VDD = 2.0V
FOSC = 32 kHz, VDD = 6.0V
(5)
Power-Down Current
IPD
Commercial
1.0
2.0
3.0
5.0
6.0
8.0*
15
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 6.0V, WDT disabled
VDD = 6.0V, WDT enabled
25
(5)
Power-Down Current
IPD
Industrial
1.0
2.0
3.0
3.0
5.0
8.0
10*
20*
18
µA
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 4.0V, WDT enabled
VDD = 6.0V, WDT disabled
VDD = 6.0V, WDT enabled
45
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 75
Enh. PIC16C5X
PIC16CR54A
11.4
DC Characteristics: PIC16CR54A-04, 10, 20, PIC16LCR54A-04 (Commercial)
PIC16CR54A-04I, 10I, 20I, PIC16LCR54A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
All Pins Except
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 11.1 and Section 11.3.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.15 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
2.0
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
VDD = 3.0V to 5.5V
Full VDD range
(5)
0.6 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.85 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
–1.0
+1.0
µA
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
–5.0
µA
µA
µA
µA
VPIN = VSS + 0.25V
(2)
0.5
0.5
0.5
+5.0
+3.0
+3.0
VPIN = VDD
T0CKI
OSC1
–3.0
–3.0
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
0.5
0.5
V
V
IOL = 10 mA, VDD = 6.0V
IOL = 1.9 mA, VDD = 6.0V,
RC option only
(3)
Output High Voltage
VOH
I/O ports
OSC2/CLKOUT
VDD –0.5
VDD –0.5
V
V
IOH = –4.0 mA, VDD = 6.0V
IOH = –0.8 mA, VDD = 6.0V,
RC option only
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30236B-page 76
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
11.5
DC Characteristics: PIC16CR54A-04E, 10E, 20E (Automotive)
DC Characteristics
All Pins Except
Standard Operating Conditions (unless otherwise specified)
Operating Temperature –40°C ≤ TA ≤ +125°C
Power Supply Pins
Operating Voltage VDD range is described in Section 11.2.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Vss
Vss
Vss
Vss
Vss
0.15 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
0.45 VDD
2.0
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
For all VDD
(5)
4.0V < VDD ≤ 5.5V
VDD > 5.5V
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
–1.0
0.5
+1.0
µA
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
–5.0
µA
µA
µA
µA
VPIN = VSS + 0.25V
(2)
0.5
0.5
0.5
+5.0
+3.0
+3.0
VPIN = VDD
T0CKI
OSC1
–3.0
–3.0
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
(3)
Output High Voltage
I/O ports
VOH
VDD –0.7
VDD –0.7
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
OSC2/CLKOUT
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1996 Microchip Technology Inc.
DS30236B-page 77
Enh. PIC16C5X
PIC16CR54A
11.6
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
T
Time
2
to
mc
osc
os
MCLR
ck
cy
drt
io
CLKOUT
cycle time
device reset timer
I/O port
oscillator
OSC1
t0
T0CKI
wdt
watchdog timer
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
FIGURE 11-1: LOAD CONDITIONS
Pin
CL = 50 pF for all pins except OSC2
CL
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
VSS
DS30236B-page 78
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
11.7
Timing Diagrams and Specifications
FIGURE 11-2: EXTERNAL CLOCK TIMING - PIC16CR54A
Q4
Q3
Q4
4
Q1
Q1
Q2
OSC1
1
3
3
4
2
CLKOUT
TABLE 11-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR54A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and Section 11.3.
Parameter
No.
(1)
Sym
Characteristic
Min Typ
Max Units
Conditions
(2)
FOSC
External CLKIN Frequency
DC
DC
DC
DC
DC
DC
DC
0.1
4.0
4.0
4.0
5.0
—
—
—
—
—
—
—
—
—
—
—
—
4.0
4.0
4.0
10
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
4.0
4.0
4.0
10
(2)
Oscillator Frequency
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1996 Microchip Technology Inc.
DS30236B-page 79
Enh. PIC16C5X
PIC16CR54A
TABLE 11-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR54A (CON’T)
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and Section 11.3.
Parameter
(1)
No.
Sym
Characteristic
Min Typ
Max Units
Conditions
RC osc mode
(2)
1
TOSC
External CLKIN Period
250
250
250
100
50
—
—
—
—
ns
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
—
ns
ns
µs
ns
ns
ns
XT osc mode
—
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
—
—
5.0
250
250
250
100
50
—
—
(2)
Oscillator Period
—
—
RC osc mode
—
10,000
250
250
250
200
—
XT osc mode
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
5.0
—
—
(3)
2
3
TCY
Instruction Cycle Time
4/FOSC
—
TosL, TosH Clock in (OSC1) Low or High Time
50*
20*
2.0*
—
—
XT oscillator
HS oscillator
LP oscillator
XT oscillator
HS oscillator
LP oscillator
—
—
—
—
4
TosR, TosF Clock in (OSC1) Rise or Fall Time
—
25*
25*
50*
—
—
—
—
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30236B-page 80
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
FIGURE 11-3: CLKOUT AND I/O TIMING - PIC16CR54A
Q1
Q2
Q3
Q4
OSC1
10
11
CLKOUT
12
13
18
19
16
14
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 11-3: CLKOUT AND I/O TIMING REQUIREMENTS - PIC16CR54A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and
Section 11.3.
Parameter
(1)
No.
Sym
Characteristic
(2)
Min
Typ
Max
Units
10
11
12
13
14
15
16
17
18
TosH2ckL
TosH2ckH
TckR
OSC1↑ to CLKOUT↓
—
15
15
5.0
5.0
—
30**
30**
15**
15**
40**
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
(2)
OSC1↑ to CLKOUT↑
—
(2)
CLKOUT rise time
—
(2)
TckF
CLKOUT fall time
—
(2)
CLKOUT↓ to Port out valid
TckL2ioV
TioV2ckH
TckH2ioI
TosH2ioV
TosH2ioI
—
(2)
Port in valid before CLKOUT↑
(2)
0.25 TCY+30*
—
Port in hold after CLKOUT↑
OSC1↑ (Q1 cycle) to Port out valid
0*
—
—
—
(3)
—
100*
—
OSC1↑ (Q2 cycle) to Port input invalid (I/O in
TBD
—
hold time)
19
TioV2osH
Port input valid to OSC1↑
TBD
—
—
ns
(I/O in setup time)
(3)
20
21
TioR
TioF
Port output rise time
—
—
10
10
25**
25**
ns
ns
(3)
Port output fall time
*
These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 11-1 for loading conditions.
1996 Microchip Technology Inc.
DS30236B-page 81
Enh. PIC16C5X
PIC16CR54A
FIGURE 11-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER TIMING - PIC16CR54A
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 11-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16CR54A
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and Section 11.3.
Parameter
No.
(1)
Sym Characteristic
Min Typ
Max Units
Conditions
30
31
TmcL MCLR Pulse Width (low)
1.0*
7.0*
—
—
µs VDD = 5.0V
Twdt Watchdog Timer Time-out Period
(No Prescaler)
18*
40*
ms VDD = 5.0V (Commercial)
32
34
TDRT Device Reset Timer Period
7.0*
—
18*
—
30*
ms VDD = 5.0V (Commercial)
TioZ I/O Hi-impedance from MCLR Low
1.0*
µs
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30236B-page 82
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
FIGURE 11-5: TIMER0 CLOCK TIMINGS - PIC16CR54A
T0CKI
40
41
42
TABLE 11-5: TIMER0 CLOCK REQUIREMENTS - PIC16CR54A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and
Section 11.3.
Parameter
(1)
Sym Characteristic
Min
Typ
Max Units Conditions
No.
40
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
41
42
Tt0L T0CKI Low Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
Tt0P T0CKI Period
20 or TCY + 40*
N
ns Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
1996 Microchip Technology Inc.
DS30236B-page 83
Enh. PIC16C5X
PIC16CR54A
NOTES:
DS30236B-page 84
1996 Microchip Technology Inc.
PIC16CR54B/56/58B Enh. PIC16C5X
12.0 ELECTRICAL CHARACTERISTICS - PIC16CR54B/56/58B
Absolute Maximum Ratings†
Ambient Temperature under bias...........................................................................................................–55°C to +125°C
Storage Temperature .............................................................................................................................–65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
(2)
Voltage on MCLR with respect to VSS ............................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
(1)
Total Power Dissipation ....................................................................................................................................800 mW
Max. Current out of VSS pin ..................................................................................................................................150 mA
Max. Current into VDD pin .......................................................................................................................................50 mA
Max. Current into an input pin (T0CKI only) ....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD)....................................................................................................................±20 mA
Output Clamp Current, IOK (V0 < 0 or V0 > VDD).............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin................................................................................................................25 mA
Max. Output Current sourced by any I/O pin...........................................................................................................20 mA
Max. Output Current sourced by a single I/O port (PORTA or B)............................................................................40 mA
Max. Output Current sunk by a single I/O port (PORTA or B).................................................................................50 mA
Note 1: Power Dissipation is calculated as follows: PDIS = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
Note 2: Voltage spikes below Vss at the MCLR pin, inducing currents greater than 80 mA may cause latch-up. Thus,
a series resistor of 50 to 100Ω should be used when applying a low level to the MCLR pin rather than pulling
this pin directly to Vss.
†
NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1996 Microchip Technology Inc.
DS30236B-page 85
Enh. PIC16C5X PIC16CR54B/56/58B
TABLE 12-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16CR54B-04
PIC16CR56-04
PIC16CR58B-04
PIC16CR54B-10
PIC16CR56-10
PIC16CR58B-10
PIC16CR54B-20
PIC16CR56-20
PIC16CR58B-20
PIC16LCR54B-04
PIC16LCR56-04
PIC16LCR58B-04
OSC
RC
VDD: 2.5 V to 5.5V
IDD: 3.6 mA max at 6.0V
IPD: 6.0 µA max at 2.5V,
WDT dis
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Freq: 4.0 MHz max
XT
HS
LP
VDD: 2.5V to 5.5V
IDD: 3.6 mA max at 6.0V
IPD: 6.0 µA max at 2.5V,
WDT dis
Freq: 4.0 MHz max
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 10 mA max at 5.5V
IPD: 6.0 µA max at 2.5V,
WDT dis
IDD: 10 mA max at 5.5V
IPD: 6.0 µA max at 2.5V,
WDT dis
N/A
N/A
Freq: 10 MHz max
Freq: 20 MHz max
VDD: 2.5V to 5.5V
IDD: 20 µA max at 32 kHz,
2.0V
IPD: 6.0 µA max at 2.5V,
WDT dis
N/A
N/A
Freq: 200 kHz max
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30236B-page 86
1996 Microchip Technology Inc.
PIC16CR54B/56/58B Enh. PIC16C5X
12.1
DC Characteristics: PIC16CR54B/56/58B-04, 10, 20 (Commercial)
PIC16CR54B/56/58B-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym
Min Typ
Max
Units
Conditions
Supply Voltage
RC and XT options
HS option
VDD
2.5
4.5
5.5
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
V
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
(4)
RC and XT options
2.0
0.8
90
4.8
9.0
3.6
1.8
350
10
mA
mA
µA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 4.0 MHz, VDD = 3.0V
FOSC = 200 kHz, VDD = 2.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
HS option
mA
mA
20
(5)
Power-Down Current
Commercial
IPD
IPD
1.0
2.0
3.0
5.0
6.0
8.0*
15
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 5.5V, WDT disabled
VDD = 5.5V, WDT enabled
25
(5)
Power-Down Current
Industrial
1.0
2.0
3.0
3.0
5.0
8.0
10*
20*
18
µA
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 4.0V, WDT enabled
VDD = 5.5V, WDT disabled
VDD = 5.5V, WDT enabled
45
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 87
Enh. PIC16C5X PIC16CR54B/56/58B
12.2
DC Characteristics: PIC16CR54B/56/58B-04E, 10E, 20E (Automotive)
DC Characteristics
Power Supply Pins
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (automotive)
(1)
Characteristic
Sym
Min Typ
Max Units
Conditions
Supply Voltage
RC and XT options
HS options
VDD
3.25
4.5
5.5
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
V
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
(4)
RC and XT options
1.8
4.8
9.0
3.3
10
20
mA
mA
mA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 16 MHz, VDD = 5.5V
HS option
(5)
Power-Down Current
IPD
5.0
0.8
22
18
µA
µA
VDD = 3.25V, WDT enabled
VDD = 3.25V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design
guidance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30236B-page 88
1996 Microchip Technology Inc.
PIC16CR54B/56/58B Enh. PIC16C5X
12.3
DC Characteristics: PIC16LCR54B/56/58B-04 (Commercial)
PIC16LCR54B/56/58B-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym
Min Typ
Max
Units
Conditions
Supply Voltage
VDD
VDR
2.5
5.5
V
V
V
(2)
RAM Data Retention Voltage
1.5*
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
10
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
20
70
µA
µA
FOSC = 32 kHz, VDD = 2.0V
FOSC = 32 kHz, VDD = 5.5V
(5)
Power-Down Current
IPD
Commercial
1.0
2.0
3.0
5.0
6.0
8.0*
15
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 5.5V, WDT disabled
VDD = 5.5V, WDT enabled
25
(5)
Power-Down Current
IPD
Industrial
1.0
2.0
3.0
3.0
5.0
8.0
10*
20*
18
µA
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 4.0V, WDT enabled
VDD = 5.5V, WDT disabled
VDD = 5.5V, WDT enabled
45
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 89
Enh. PIC16C5X PIC16CR54B/56/58B
12.4
DC Characteristics: PIC16CR54B/56/58B-04, 10, 20 (Commercial)
PIC16LCR54B/56/58B-04 (Commercial)
PIC16CR54B/56/58B-04I, 10I, 20I (Industrial)
PIC16LCR54B/56/58B-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
All Pins Except
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 12.1 and Section 12.3.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.15 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
2.0
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
VDD = 3.0V to 5.5V
Full VDD range
(5)
0.6 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.85 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
–1.0
+1.0
µA
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
–5.0
µA
µA
µA
µA
VPIN = VSS + 0.25V
(2)
0.5
0.5
0.5
+5.0
+3.0
+3.0
VPIN = VDD
T0CKI
OSC1
–3.0
–3.0
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
(3)
Output High Voltage
VOH
I/O ports
OSC2/CLKOUT
VDD –0.7
VDD –0.7
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30236B-page 90
1996 Microchip Technology Inc.
PIC16CR54B/56/58B Enh. PIC16C5X
12.5
DC Characteristics: PIC16CR54B/56/58B-04E, 10E, 20E (Automotive)
DC Characteristics
All Pins Except
Standard Operating Conditions (unless otherwise specified)
Operating Temperature –40°C ≤ TA ≤ +125°C
Power Supply Pins
Operating Voltage VDD range is described in Section 12.2.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Vss
Vss
Vss
Vss
Vss
0.15 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
0.45 VDD
2.0
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
For all VDD
(5)
4.0V < VDD ≤ 5.5V
VDD > 5.5V
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
–1.0
0.5
+1.0
µA
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
–5.0
µA
µA
µA
µA
VPIN = VSS + 0.25V
(2)
0.5
0.5
0.5
+5.0
+3.0
+3.0
VPIN = VDD
T0CKI
OSC1
–3.0
–3.0
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
(3)
Output High Voltage
I/O ports
VOH
VDD –0.7
VDD –0.7
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
OSC2/CLKOUT
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1996 Microchip Technology Inc.
DS30236B-page 91
Enh. PIC16C5X PIC16CR54B/56/58B
12.6
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
T
Time
2
to
mc
osc
os
MCLR
ck
cy
drt
io
CLKOUT
cycle time
device reset timer
I/O port
oscillator
OSC1
t0
T0CKI
wdt
watchdog timer
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
FIGURE 12-1: LOAD CONDITIONS
Pin
CL = 50 pF for all pins except OSC2
CL
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
VSS
DS30236B-page 92
1996 Microchip Technology Inc.
PIC16CR54B/56/58B Enh. PIC16C5X
12.7
Timing Diagrams and Specifications
FIGURE 12-2: EXTERNAL CLOCK TIMING - PIC16CR54B/56/58B
Q4
Q3
Q4
4
Q1
Q1
Q2
OSC1
1
3
3
4
2
CLKOUT
TABLE 12-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR54B/56/58B
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 12.1, Section 12.2 and Section 12.3.
Parameter
No.
(1)
Sym
Characteristic
Min Typ
Max Units
Conditions
(2)
FOSC
External CLKIN Frequency
DC
DC
DC
DC
DC
DC
DC
0.1
4.0
4.0
4.0
5.0
—
—
—
—
—
—
—
—
—
—
—
—
4.0
4.0
4.0
10
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
4.0
4.0
4.0
10
(2)
Oscillator Frequency
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1996 Microchip Technology Inc.
DS30236B-page 93
Enh. PIC16C5X PIC16CR54B/56/58B
TABLE 12-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR54B/56/58B (CON’T)
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 12.1, Section 12.2 and Section 12.3.
Parameter
(1)
No.
Sym
Characteristic
Min Typ
Max Units
Conditions
RC osc mode
(2)
1
TOSC
External CLKIN Period
250
250
250
100
50
—
—
—
—
ns
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
—
ns
ns
µs
ns
ns
ns
XT osc mode
—
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
—
—
5.0
250
250
250
100
50
—
—
(2)
Oscillator Period
—
—
RC osc mode
—
10,000
250
250
250
200
—
XT osc mode
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
5.0
—
—
(3)
2
3
TCY
Instruction Cycle Time
4/FOSC
—
TosL, TosH Clock in (OSC1) Low or High Time
50*
20*
2.0*
—
—
XT oscillator
HS oscillator
LP oscillator
XT oscillator
HS oscillator
LP oscillator
—
—
—
—
4
TosR, TosF Clock in (OSC1) Rise or Fall Time
—
25*
25*
50*
—
—
—
—
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30236B-page 94
1996 Microchip Technology Inc.
PIC16CR54B/56/58B Enh. PIC16C5X
FIGURE 12-3: CLKOUT AND I/O TIMING - PIC16CR54B/56/58B
Q1
Q2
Q3
Q4
OSC1
10
11
CLKOUT
12
13
18
19
16
14
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 12-3: CLKOUT AND I/O TIMING REQUIREMENTS - PIC16CR54B/56/58B
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 12.1, Section 12.2 and
Section 12.3.
Parameter
(1)
No.
Sym
Characteristic
(2)
Min
Typ
Max
Units
10
11
12
13
14
15
16
17
18
TosH2ckL
TosH2ckH
TckR
OSC1↑ to CLKOUT↓
—
15
15
5
30**
30**
15**
15**
40**
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
(2)
OSC1↑ to CLKOUT↑
—
(2)
CLKOUT rise time
—
(2)
TckF
CLKOUT fall time
—
5
(2)
CLKOUT↓ to Port out valid
TckL2ioV
TioV2ckH
TckH2ioI
TosH2ioV
TosH2ioI
—
—
—
—
—
—
(2)
Port in valid before CLKOUT↑
(2)
0.25 TCY+30*
Port in hold after CLKOUT↑
OSC1↑ (Q1 cycle) to Port out valid
0*
—
—
(3)
100*
—
OSC1↑ (Q2 cycle) to Port input invalid (I/O in
TBD
hold time)
19
TioV2osH
Port input valid to OSC1↑
TBD
—
—
ns
(I/O in setup time)
(3)
20
21
TioR
TioF
Port output rise time
—
—
10
10
25**
25**
ns
ns
(3)
Port output fall time
*
These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 12-1 for loading conditions.
1996 Microchip Technology Inc.
DS30236B-page 95
Enh. PIC16C5X PIC16CR54B/56/58B
FIGURE 12-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER TIMING -
PIC16CR54B/56/58B
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 12-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16CR54B/56/58B
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 12.1, Section 12.2 and Section 12.3.
Parameter
No.
(1)
Sym Characteristic
Min Typ
Max Units
Conditions
30
31
TmcL MCLR Pulse Width (low)
1.0*
7.0*
—
—
µs VDD = 5.0V
Twdt Watchdog Timer Time-out Period
(No Prescaler)
18*
40*
ms VDD = 5.0V (Commercial)
32
34
TDRT Device Reset Timer Period
7.0*
—
18*
—
30*
ms VDD = 5.0V (Commercial)
TioZ I/O Hi-impedance from MCLR Low
1.0*
µs
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30236B-page 96
1996 Microchip Technology Inc.
PIC16CR54B/56/58B Enh. PIC16C5X
FIGURE 12-5: TIMER0 CLOCK TIMINGS - PIC16CR54B/56/58B
T0CKI
40
41
42
TABLE 12-5: TIMER0 CLOCK REQUIREMENTS - PIC16CR54B/56/58B
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 12.1, Section 12.2 and
Section 12.3.
Parameter
(1)
Sym Characteristic
Min
Typ
Max Units Conditions
No.
40
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
41
42
Tt0L T0CKI Low Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
Tt0P T0CKI Period
20 or TCY + 40*
N
ns Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
1996 Microchip Technology Inc.
DS30236B-page 97
Enh. PIC16C5X PIC16CR54B/56/58B
NOTES:
DS30236B-page 98
1996 Microchip Technology Inc.
PIC16CR57A Enh. PIC16C5X
13.0 ELECTRICAL CHARACTERISTICS - PIC16CR57A
Absolute Maximum Ratings†
Ambient Temperature under bias...........................................................................................................–55°C to +125°C
Storage Temperature .............................................................................................................................–65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
(2)
Voltage on MCLR with respect to VSS ............................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
(1)
Total Power Dissipation ....................................................................................................................................800 mW
Max. Current out of VSS pin ..................................................................................................................................150 mA
Max. Current into VDD pin .....................................................................................................................................100 mA
Max. Current into an input pin (T0CKI only) ....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD)....................................................................................................................±20 mA
Output Clamp Current, IOK (V0 < 0 or V0 > VDD).............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin................................................................................................................25 mA
Max. Output Current sourced by any I/O pin...........................................................................................................20 mA
Max. Output Current sourced by a single I/O port
PORTA .........................................................................................................................................................50 mA
PORTB or C ...............................................................................................................................................100 mA
Max. Output Current sunk by a single I/O port
PORTA .........................................................................................................................................................50 mA
PORTB or C ...............................................................................................................................................100 mA
Note 1: Power Dissipation is calculated as follows: PDIS = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
Note 2: Voltage spikes below Vss at the MCLR pin, inducing currents greater than 80 mA may cause latch-up. Thus,
a series resistor of 50 to 100Ω should be used when applying a low level to the MCLR pin rather than pulling
this pin directly to Vss.
†
NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1996 Microchip Technology Inc.
DS30236B-page 99
Enh. PIC16C5X
PIC16CR57A
TABLE 13-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
OSC
PIC16CR57A-04
PIC16CR57A-10
PIC16CR57A-20
PIC16LCR57A-04
RC
VDD: 3.0V to 6.25V
IDD: 3.3 mA max at 5.5V
IPD: 9.0 µA max at 3.0V,
WDT dis
N/A
N/A
N/A
Freq: 4.0 MHz max
XT
HS
LP
VDD: 3.0V to 6.25V
IDD: 3.3 mA max at 5.5V
IPD: 9.0 µA max at 3.0V,
WDT dis
N/A
N/A
N/A
N/A
Freq: 4.0 MHz max
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 10 mA max at 5.5V
IPD: 9.0 µA max at 3.0V,
WDT dis
IDD: 20 mA max at 5.5V
IPD: 9.0 µA max at 3.0V,
WDT dis
N/A
N/A
Freq: 10 MHz max
Freq: 20 MHz max
VDD: 2.5V to 6.25V
IDD: 32 µA max at 32 kHz,
2.5V
IPD: 9.0 µA max at 2.5V,
WDT dis
N/A
N/A
Freq: 200 kHz max
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30236B-page 100
1996 Microchip Technology Inc.
PIC16CR57A Enh. PIC16C5X
13.1
DC Characteristics: PIC16CR57A-04, 10, 20 (Commercial)
PIC16CR57A-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym
Min Typ
Max
Units
Conditions
Supply Voltage
RC and XT options
HS option
VDD
3.0
4.5
6.25
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
V
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
(4)
RC and XT options
1.8
4.8
9.0
3.3
10
20
mA
mA
mA
FOSC = 4 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
HS option
(5)
Power-Down Current
IPD
Commercial
4.0
0.6
5.0
0.8
12
9.0
14
14
µA
µA
µA
µA
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
Industrial
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 101
Enh. PIC16C5X
PIC16CR57A
13.2
DC Characteristics: PIC16LCR57A-04 (Commercial)
PIC16LCR57A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym
Min Typ
Max
Units
Conditions
Supply Voltage
VDD
VDR
2.5
6.25
V
V
V
(2)
RAM Data Retention Voltage
1.5*
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
Commercial
15
19
32
40
µA
µA
FOSC = 32 kHz, VDD = 2.5V,
WDT disabled
FOSC = 32 kHz, VDD = 2.5V,
WDT disabled
Industrial
(5)
Power-Down Current
IPD
Commercial
4.0
0.6
5.0
0.8
12
9
14
12
µA
µA
µA
µA
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
Industrial
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30236B-page 102
1996 Microchip Technology Inc.
PIC16CR57A Enh. PIC16C5X
13.3
DC Characteristics: PIC16CR57A-04, 10, 20, PIC16LCR57A-04 (Commercial)
PIC16CR57A-04I, 10I, 20I, PIC16LCR57A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
All Pins Except
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 13.1 and Section 13.2.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
0.45 VDD
2.0
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
For all VDD
(5)
4.0V < VDD ≤ 5.5
VDD > 5.5V
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
–1.0
+1.0
µA
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
–5.0
µA
µA
µA
µA
VPIN = VSS + 0.25V
(2)
0.5
0.5
0.5
+5.0
+3.0
+3.0
VPIN = VDD
T0CKI
OSC1
–3.0
–3.0
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
(3)
Output High Voltage
VOH
I/O ports
OSC2/CLKOUT
VDD –0.7
VDD –0.7
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1996 Microchip Technology Inc.
DS30236B-page 103
Enh. PIC16C5X
PIC16CR57A
13.4
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
T
Time
2
to
mc
osc
os
MCLR
ck
cy
drt
io
CLKOUT
cycle time
device reset timer
I/O port
oscillator
OSC1
t0
T0CKI
wdt
watchdog timer
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
FIGURE 13-1: LOAD CONDITIONS
Pin
CL = 50 pF for all pins except OSC2
CL
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
VSS
DS30236B-page 104
1996 Microchip Technology Inc.
PIC16CR57A Enh. PIC16C5X
13.5
Timing Diagrams and Specifications
FIGURE 13-2: EXTERNAL CLOCK TIMING - PIC16CR57A
Q4
Q3
Q4
4
Q1
Q1
Q2
OSC1
1
3
3
4
2
CLKOUT
TABLE 13-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR57A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 13.1 and Section 13.2.
Parameter
No.
(1)
Sym
Characteristic
Min Typ
Max Units
Conditions
(2)
FOSC
External CLKIN Frequency
DC
DC
DC
DC
DC
DC
DC
0.1
4.0
4.0
4.0
5.0
—
—
—
—
—
—
—
—
—
—
—
—
4.0
4.0
4.0
10
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
4.0
4.0
4.0
10
(2)
Oscillator Frequency
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1996 Microchip Technology Inc.
DS30236B-page 105
Enh. PIC16C5X
PIC16CR57A
TABLE 13-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR57A (CON’T)
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 13.1 and Section 13.2.
Parameter
(1)
No.
Sym
Characteristic
Min Typ
Max Units
Conditions
RC osc mode
(2)
1
TOSC
External CLKIN Period
250
250
250
100
50
—
—
—
—
ns
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
—
ns
ns
µs
ns
ns
ns
XT osc mode
—
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
—
—
5.0
250
250
250
100
50
—
—
(2)
Oscillator Period
—
—
RC osc mode
—
10,000
250
250
250
200
—
XT osc mode
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
5.0
—
—
(3)
2
3
TCY
Instruction Cycle Time
4/FOSC
—
TosL, TosH Clock in (OSC1) Low or High Time
50*
20*
2.0*
—
—
XT oscillator
HS oscillator
LP oscillator
XT oscillator
HS oscillator
LP oscillator
—
—
—
—
4
TosR, TosF Clock in (OSC1) Rise or Fall Time
—
25*
25*
50*
—
—
—
—
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30236B-page 106
1996 Microchip Technology Inc.
PIC16CR57A Enh. PIC16C5X
FIGURE 13-3: CLKOUT AND I/O TIMING - PIC16CR57A
Q1
Q2
Q3
Q4
OSC1
10
11
CLKOUT
12
13
18
19
16
14
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 13-3: CLKOUT AND I/O TIMING REQUIREMENTS - PIC16CR57A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 13.1 and Section 13.2.
Parameter
(1)
No.
Sym
Characteristic
(2)
Min
Typ
Max
Units
10
11
12
13
14
15
16
17
18
TosH2ckL
TosH2ckH
TckR
OSC1↑ to CLKOUT↓
—
15
15
5
30**
30**
15**
15**
40**
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
(2)
OSC1↑ to CLKOUT↑
—
(2)
CLKOUT rise time
—
(2)
TckF
CLKOUT fall time
—
5
(2)
CLKOUT↓ to Port out valid
TckL2ioV
TioV2ckH
TckH2ioI
TosH2ioV
TosH2ioI
—
—
—
—
—
—
(2)
Port in valid before CLKOUT↑
(2)
0.25 TCY+30*
Port in hold after CLKOUT↑
OSC1↑ (Q1 cycle) to Port out valid
0*
—
—
(3)
100*
—
OSC1↑ (Q2 cycle) to Port input invalid (I/O in
TBD
hold time)
19
TioV2osH
Port input valid to OSC1↑
TBD
—
—
ns
(I/O in setup time)
(3)
20
21
TioR
TioF
Port output rise time
—
—
10
10
25**
25**
ns
ns
(3)
Port output fall time
*
These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 13-1 for loading conditions.
1996 Microchip Technology Inc.
DS30236B-page 107
Enh. PIC16C5X
PIC16CR57A
FIGURE 13-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER TIMING - PIC16CR57A
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 13-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16CR57A
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 13.1 and Section 13.2.
Parameter
No.
(1)
Sym Characteristic
Min Typ
Max Units
Conditions
30
31
TmcL MCLR Pulse Width (low)
100*
7.0*
—
—
ns VDD = 5.0V
Twdt Watchdog Timer Time-out Period
(No Prescaler)
18*
40*
ms VDD = 5.0V (Commercial)
32
34
TDRT Device Reset Timer Period
7.0*
—
18*
—
30*
ms VDD = 5.0V (Commercial)
ns
TioZ I/O Hi-impedance from MCLR Low
100*
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30236B-page 108
1996 Microchip Technology Inc.
PIC16CR57A Enh. PIC16C5X
FIGURE 13-5: TIMER0 CLOCK TIMINGS - PIC16CR57A
T0CKI
40
41
42
TABLE 13-5: TIMER0 CLOCK REQUIREMENTS - PIC16CR57A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 13.1 and Section 13.2.
Parameter
(1)
Sym Characteristic
Min
Typ
Max Units Conditions
No.
40
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
41
42
Tt0L T0CKI Low Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
Tt0P T0CKI Period
20 or TCY + 40*
N
ns Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
1996 Microchip Technology Inc.
DS30236B-page 109
Enh. PIC16C5X
PIC16CR57A
NOTES:
DS30236B-page 110
1996 Microchip Technology Inc.
PIC16CR57B Enh. PIC16C5X
14.0 ELECTRICAL CHARACTERISTICS - PIC16CR57B
Absolute Maximum Ratings†
Ambient Temperature under bias...........................................................................................................–55°C to +125°C
Storage Temperature .............................................................................................................................–65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
(2)
Voltage on MCLR with respect to VSS ............................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
(1)
Total Power Dissipation ....................................................................................................................................800 mW
Max. Current out of VSS pin ..................................................................................................................................150 mA
Max. Current into VDD pin .....................................................................................................................................100 mA
Max. Current into an input pin (T0CKI only) ....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD)....................................................................................................................±20 mA
Output Clamp Current, IOK (V0 < 0 or V0 > VDD).............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin................................................................................................................25 mA
Max. Output Current sourced by any I/O pin...........................................................................................................20 mA
Max. Output Current sourced by a single I/O port
PORTA .........................................................................................................................................................50 mA
PORTB or C ...............................................................................................................................................100 mA
Max. Output Current sunk by a single I/O port
PORTA .........................................................................................................................................................50 mA
PORTB or C ...............................................................................................................................................100 mA
Note 1: Power Dissipation is calculated as follows: PDIS = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
Note 2: Voltage spikes below Vss at the MCLR pin, inducing currents greater than 80 mA may cause latch-up. Thus,
a series resistor of 50 to 100Ω should be used when applying a low level to the MCLR pin rather than pulling
this pin directly to Vss.
†
NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1996 Microchip Technology Inc.
DS30236B-page 111
Enh. PIC16C5X
PIC16CR57B
TABLE 14-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
OSC
PIC16CR57B-04
PIC16CR57B-10
PIC16CR57B-20
PIC16LCR57B-04
RC
VDD: 3.0V to 6.25V
IDD: 2.5 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
N/A
N/A
N/A
Freq: 4.0 MHz max
XT
HS
LP
VDD: 3.0V to 6.25V
IDD: 2.5 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
N/A
N/A
N/A
N/A
Freq: 4.0 MHz max
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 10 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
IDD: 20 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
N/A
N/A
Freq: 10 MHz max
Freq: 20 MHz max
VDD: 2.5V to 6.25V
IDD: 32 µA max at 32 kHz,
2.5V
IPD: 4.0 µA max at 2.5V,
WDT dis
N/A
N/A
Freq: 200 kHz max
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30236B-page 112
1996 Microchip Technology Inc.
PIC16CR57B Enh. PIC16C5X
14.1
DC Characteristics: PIC16CR57B-04, 10, 20 (Commercial)
PIC16CR57B-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym
Min Typ
Max
Units
Conditions
Supply Voltage
RC and XT options
HS option
VDD
3.0
4.5
6.25
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
V
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
(4)
RC and XT options
1.9
2.5
4.7
2.5
8.0
17
mA
mA
mA
FOSC = 4 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
HS option
(5)
Power-Down Current
IPD
Commercial
4.0
0.25
5.0
12
4.0
14
µA
µA
µA
µA
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
Industrial
0.3
5.0
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 113
Enh. PIC16C5X
PIC16CR57B
14.2
DC Characteristics: PIC16CR57B-04E, 10E, 20E (Automotive)
DC Characteristics
Power Supply Pins
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (automotive)
(1)
Characteristic
Sym
Min Typ
Max Units
Conditions
Supply Voltage
RC and XT options
HS options
VDD
3.25
4.5
6.0
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
V
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
(4)
RC and XT options
1.9
4.8
9.0
3.3
10
20
mA
mA
mA
FOSC = 4 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 16 MHz, VDD = 5.5V
HS option
(5)
Power-Down Current
IPD
5.0
0.8
22
18
µA
µA
VDD = 3.25V, WDT enabled
VDD = 3.25V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design
guidance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30236B-page 114
1996 Microchip Technology Inc.
PIC16CR57B Enh. PIC16C5X
14.3
DC Characteristics: PIC16LCR57B-04 (Commercial)
PIC16LCR57B-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym
Min Typ
Max
Units
Conditions
Supply Voltage
VDD
VDR
2.5
6.25
V
V
V
(2)
RAM Data Retention Voltage
1.5*
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
Commercial
12
15
28
37
µA
µA
FOSC = 32 kHz, VDD = 2.5V,
WDT disabled
FOSC = 32 kHz, VDD = 2.5V,
WDT disabled
Industrial
(5)
Power-Down Current
IPD
Commercial
4.0
0.25
5.0
12
4.0
14
µA
µA
µA
µA
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
Industrial
0.3
5.0
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 115
Enh. PIC16C5X
PIC16CR57B
14.4
DC Characteristics: PIC16CR57B-04, 10, 20, PIC16LCR57B-04 (Commercial)
PIC16CR57B-04I, 10I, 20I, PIC16LCR57B-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
All Pins Except
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 14.1 and Section 14.3.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
0.45 VDD
2.0
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
For all VDD
(5)
4.0V < VDD ≤ 5.5V
VDD > 5.5V
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
–1.0
+1.0
µA
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
–5.0
µA
µA
µA
µA
VPIN = VSS + 0.25V
(2)
0.5
0.5
0.5
+5.0
+3.0
+3.0
VPIN = VDD
T0CKI
OSC1
–3.0
–3.0
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
(3)
Output High Voltage
VOH
I/O ports
OSC2/CLKOUT
VDD –0.7
VDD –0.7
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30236B-page 116
1996 Microchip Technology Inc.
PIC16CR57B Enh. PIC16C5X
14.5
DC Characteristics: PIC16CR57B-04E, 10E, 20E (Automotive)
DC Characteristics
All Pins Except
Standard Operating Conditions (unless otherwise specified)
Operating Temperature –40°C ≤ TA ≤ +125°C
Power Supply Pins
Operating Voltage VDD range is described in Section 14.2.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
0.45 VDD
2.0
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
For all VDD
(5)
4.0V < VDD ≤ 5.5V
VDD > 5.5V
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
–1.0
+1.0
µA
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
–5.0
µA
µA
µA
µA
VPIN = VSS + 0.25 V
VPIN = VDD
VSS ≤ VPIN ≤ VDD
(2)
0.5
0.5
0.5
+5.0
+3.0
+3.0
T0CKI
OSC1
–3.0
–3.0
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
(3)
Output High Voltage
VOH
I/O ports
OSC2/CLKOUT
VDD –0.7
VDD –0.7
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1996 Microchip Technology Inc.
DS30236B-page 117
Enh. PIC16C5X
PIC16CR57B
14.6
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
T
Time
2
to
mc
osc
os
MCLR
ck
cy
drt
io
CLKOUT
cycle time
device reset timer
I/O port
oscillator
OSC1
t0
T0CKI
wdt
watchdog timer
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
FIGURE 14-1: LOAD CONDITIONS
Pin
CL = 50 pF for all pins except OSC2
CL
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
VSS
DS30236B-page 118
1996 Microchip Technology Inc.
PIC16CR57B Enh. PIC16C5X
14.7
Timing Diagrams and Specifications
FIGURE 14-2: EXTERNAL CLOCK TIMING - PIC16CR57B
Q4
Q3
Q4
4
Q1
Q1
Q2
OSC1
1
3
3
4
2
CLKOUT
TABLE 14-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR57B
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and Section 14.3.
Parameter
No.
(1)
Sym
Characteristic
Min Typ
Max Units
Conditions
(2)
FOSC
External CLKIN Frequency
DC
DC
DC
DC
DC
DC
DC
0.1
4.0
4.0
4.0
5.0
—
—
—
—
—
—
—
—
—
—
—
—
4.0
4.0
4.0
10
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
4.0
4.0
4.0
10
(2)
Oscillator Frequency
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1996 Microchip Technology Inc.
DS30236B-page 119
Enh. PIC16C5X
PIC16CR57B
TABLE 14-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR57B (CON’T)
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and Section 14.3.
Parameter
(1)
No.
Sym
Characteristic
Min Typ
Max Units
Conditions
RC osc mode
(2)
1
TOSC
External CLKIN Period
250
250
250
100
50
—
—
—
—
ns
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
—
ns
ns
µs
ns
ns
ns
XT osc mode
—
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
—
—
5.0
250
250
250
100
50
—
—
(2)
Oscillator Period
—
—
RC osc mode
—
10,000
250
250
250
200
—
XT osc mode
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
5.0
—
—
(3)
2
3
TCY
Instruction Cycle Time
4/FOSC
—
TosL, TosH Clock in (OSC1) Low or High Time
50*
20*
2.0*
—
—
XT oscillator
HS oscillator
LP oscillator
XT oscillator
HS oscillator
LP oscillator
—
—
—
—
4
TosR, TosF Clock in (OSC1) Rise or Fall Time
—
25*
25*
50*
—
—
—
—
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30236B-page 120
1996 Microchip Technology Inc.
PIC16CR57B Enh. PIC16C5X
FIGURE 14-3: CLKOUT AND I/O TIMING - PIC16CR57B
Q1
Q2
Q3
Q4
OSC1
10
11
CLKOUT
12
13
18
19
16
14
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 14-3: CLKOUT AND I/O TIMING REQUIREMENTS - PIC16CR57B
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and
Section 14.3.
Parameter
(1)
No.
Sym
Characteristic
(2)
Min
Typ
Max
Units
10
11
12
13
14
15
16
17
18
TosH2ckL
TosH2ckH
TckR
OSC1↑ to CLKOUT↓
—
15
15
5.0
5.0
—
30**
30**
15**
15**
40**
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
(2)
OSC1↑ to CLKOUT↑
—
(2)
CLKOUT rise time
—
(2)
TckF
CLKOUT fall time
—
(2)
CLKOUT↓ to Port out valid
TckL2ioV
TioV2ckH
TckH2ioI
TosH2ioV
TosH2ioI
—
(2)
Port in valid before CLKOUT↑
(2)
0.25 TCY+30*
—
Port in hold after CLKOUT↑
OSC1↑ (Q1 cycle) to Port out valid
0*
—
—
—
(3)
—
100*
—
OSC1↑ (Q2 cycle) to Port input invalid (I/O in
TBD
—
hold time)
19
TioV2osH
Port input valid to OSC1↑
TBD
—
—
ns
(I/O in setup time)
(3)
20
21
TioR
TioF
Port output rise time
—
—
10
10
25**
25**
ns
ns
(3)
Port output fall time
*
These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 14-1 for loading conditions.
1996 Microchip Technology Inc.
DS30236B-page 121
Enh. PIC16C5X
PIC16CR57B
FIGURE 14-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER TIMING - PIC16CR57B
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 14-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16CR57B
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and Section 14.3.
Parameter
No.
(1)
Sym Characteristic
Min Typ
Max Units
Conditions
30
31
TmcL MCLR Pulse Width (low)
1.0*
7.0*
—
—
µs VDD = 5.0V
Twdt Watchdog Timer Time-out Period
(No Prescaler)
18*
40*
ms VDD = 5.0V (Commercial)
32
34
TDRT Device Reset Timer Period
7.0*
—
18*
—
30*
ms VDD = 5.0V (Commercial)
TioZ I/O Hi-impedance from MCLR Low
1.0*
µs
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30236B-page 122
1996 Microchip Technology Inc.
PIC16CR57B Enh. PIC16C5X
FIGURE 14-5: TIMER0 CLOCK TIMINGS - PIC16CR57B
T0CKI
40
41
42
TABLE 14-5: TIMER0 CLOCK REQUIREMENTS - PIC16CR57B
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and
Section 14.3.
Parameter
(1)
Sym Characteristic
Min
Typ
Max Units Conditions
No.
40
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
41
42
Tt0L T0CKI Low Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
Tt0P T0CKI Period
20 or TCY + 40*
N
ns Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
1996 Microchip Technology Inc.
DS30236B-page 123
Enh. PIC16C5X
PIC16CR57B
NOTES:
DS30236B-page 124
1996 Microchip Technology Inc.
PIC16C58A
Enh. PIC16C5X
15.0 ELECTRICAL CHARACTERISTICS - PIC16C58A
†
Absolute Maximum Ratings
Ambient temperature under bias.............................................................................................................-55°C to +125°C
Storage temperature ............................................................................................................................. - 65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
(2)
Voltage on MCLR with respect to VSS ............................................................................................................0 to +14V
Voltage on all other pins with respect to VSS .................................................................................. -0.6V to (VDD + 0.6V)
(1)
Total power dissipation .....................................................................................................................................800 mW
Max. current out of VSS pin ...................................................................................................................................150 mA
Max. current into VDD pin......................................................................................................................................100 mA
Max. current into an input pin (T0CKI only) .....................................................................................................................±500 µA
Input clamp current, IIK (VI < 0 or VI > VDD) .....................................................................................................................±20 mA
Output clamp current, IOK (V0 < 0 or V0 > VDD) ..............................................................................................................±20 mA
Max. output current sunk by any I/O pin .................................................................................................................25 mA
Max. output current sourced by any I/O pin ............................................................................................................20 mA
Max. output current sourced by a single I/O port
PORTA .........................................................................................................................................................50 mA
PORTB.......................................................................................................................................................100 mA
Max. output current sunk by a single I/O port
PORTA .........................................................................................................................................................50 mA
PORTB.......................................................................................................................................................100 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
Note 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80mA, may cause latch-up. Thus,
a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR pin rather than pulling
this pin directly to VSS
†
NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1996 Microchip Technology Inc.
DS30236B-page 125
Enh. PIC16C5X
PIC16C58A
TABLE 15-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
OSC
PIC16C58A-04
PIC16C58A-10
PIC16C58A-20
PIC16LC58A-04
PIC16C58A/JW
VDD: 3.0V to 6.25V
IDD: 2.5 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
VDD: 3.0V to 6.25V
IDD: 1.8 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 3.0V to 6.25V
IDD: 1.8 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 2.5V to 6.25V
IDD: 0.5 mA typ. at
5.5V
IPD: 0.25 µA typ. at
2.5V WDT dis
VDD: 3.0V to 6.25V
IDD: 2.5 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
RC
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD 2.5 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
VDD: 3.0V to 6.25V
IDD: 1.8 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 3.0V to 6.25V
IDD: 1.8 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 2.5V to 6.25V
IDD: 0.5 mA typ. at
5.5V
IPD: 0.25 µA typ. at
2.5V WDT dis
VDD: 3.0V to 6.25V
IDD 2.5 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
XT
HS
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
Freq: 4.0 MHz max.
VDD: 4.5V to 5.5V
IDD: 1.9 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 4.5V to 5.5V
IDD: 8.0 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
VDD: 4.5V to 5.5V
IDD: 17 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
VDD: 4.5V to 5.5V
IDD: 17 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Do not use in
HS mode
Freq: 4.0 MHz max.
Freq: 10 MHz max.
Freq: 20 MHz max.
Freq: 20 MHz max.
VDD: 3.0V to 6.25V
IDD: 15 µA typ. at
32kHz, 3.0V
IPD: 0.25 µA typ. at
3.0V WDT dis
VDD: 2.5V to 6.25V
IDD: 28 µA max. at
32kHz, 2.5V
WDT dis
IPD: 4.0 µA max. at
2.5V WDT dis
VDD: 2.5V to 6.25V
IDD: 28 µA max. at
32kHz, 2.5V
WDT dis
IPD: 4.0 µA max. at
2.5V WDT dis
Do not use in
LP mode
Do not use in
LP mode
LP
Freq: 200 kHz max.
Freq: 200 kHz max.
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30236B-page 126
1996 Microchip Technology Inc.
PIC16C58A
Enh. PIC16C5X
15.1
DC Characteristics: PIC16C58A-04, 10, 20 (Commercial)
PIC16C58A-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym Min Typ
Max Units
Conditions
Supply Voltage
XT, RC and LP options
HS option
VDD
3.0
4.5
6.25
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
VSS
V
V
Device in SLEEP mode
See section on Power-On Reset for details
VDD start voltage to ensure
Power-On Reset
VPOR
VDD rise rate to ensure
Power-On Reset
SVDD
IDD
0.05*
V/ms See section on Power-On Reset for details
(3)
Supply Current
(4)
XT and RC options
1.9
2.5
4.7
15
2.5 mA FOSC = 4.0 MHz, VDD = 5.5V
8.0 mA FOSC = 10 MHz, VDD = 5.5V
HS option
17
mA FOSC = 20 MHz, VDD = 5.5V
µA FOSC = 32 kHz, VDD = 3.0V, WDT disabled
µA FOSC = 32 kHz, VDD = 3.0V, WDT disabled
LP option, Commercial
LP option, Industrial
18
(5)
Power Down Current
IPD
Commercial
4.0
0.25 4.0
5.0
0.3
12
µA VDD = 3.0V, WDT enabled
µA VDD = 3.0V, WDT disabled
µA VDD = 3.0V, WDT enabled
µA VDD = 3.0V, WDT disabled
Industrial
14
5.0
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design
guidance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 127
Enh. PIC16C5X
PIC16C58A
15.2
DC Characteristics: PIC16C58A-04E, 10E, 20E (Automotive)
DC Characteristics
Power Supply Pins
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (automotive)
(1)
Characteristic
Sym Min Typ
Max Units
Conditions
Supply Voltage
XT and RC options
HS option
VDD
3.5
4.5
5.5
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
VSS
V
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
See section on Power-On Reset for details
VDD rise rate to ensure
Power-On Reset
SVDD
IDD
0.05*
V/ms See section on Power-On Reset for details
(3)
Supply Current
(4)
XT and RC options
1.9
4.8
9.0
3.3 mA FOSC = 4.0 MHz, VDD = 5.5V
HS option
10
20
mA FOSC = 10 MHz, VDD = 5.5V
mA FOSC = 20 MHz, VDD = 5.5V
(5)
Power Down Current
IPD
XT and RC options
5.0
0.8
4.0
22
18
22
18
µA VDD = 3.5V, WDT enabled
µA VDD = 3.5V, WDT disabled
µA VDD = 3.5V, WDT enabled
µA VDD = 3.5V, WDT disabled
HS option
0.25
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design
guidance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30236B-page 128
1996 Microchip Technology Inc.
PIC16C58A
Enh. PIC16C5X
15.3
DC Characteristics: PIC16LC58A-04 (Commercial)
PIC16LC58A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym Min Typ
Max Units
Conditions
Supply Voltage
VDD
XT, RC and LP options
2.5
6.25
V
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
VSS
Device in SLEEP mode
See section on Power-On Reset for details
VDD start voltage to ensure
Power-On Reset
VPOR
VDD rise rate to ensure
Power-On Reset
SVDD
IDD
0.05*
V/ms See section on Power-On Reset for details
(3)
Supply Current
(4)
XT and RC options
0.5
12
15
mA FOSC = 4.0 MHz, VDD = 5.5V
µA FOSC = 32 kHz, VDD = 2.5V WDT disabled
µA FOSC = 32 kHz, VDD = 2.5V WDT disabled
LP option, Commercial
LP option, Industrial
28
37
(5)
Power Down Current
IPD
Commercial
2.5
0.25 4.0
3.5
0.3
12
µA VDD = 2.5V, WDT enabled
µA VDD = 2.5V, WDT disabled
µA VDD = 2.5V, WDT enabled
µA VDD = 2.5V, WDT disabled
Industrial
14
5.0
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guid-
ance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 129
Enh. PIC16C5X
PIC16C58A
15.4
DC Characteristics: PIC16C58A-04, 10, 20, PIC16LC58A-04 (Commercial),
PIC16C58A-04I, 10I, 20I, PIC16LC58A-04I (Industrial),
PIC16C58A-04E, 10E, 20E (Automotive)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (automotive)
DC Characteristics
All Pins Except
Power Supply Pins
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and
Section 15.3.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
0.2 VDD+1V
2.0
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
For all VDD
(5)
4.0V < VDD ≤ 5.5V
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
-1.0
-5.0
0.5
+1.0
µA VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
µA VPIN = VSS +0.25V
(2)
0.5
0.5
0.5
+5.0
+3.0
+3.0
µA VPIN = VDD
T0CKI
OSC1
-3.0
-3.0
µA VSS ≤ VPIN ≤ VDD
µA VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
VOH
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
Output High Voltage
(3)
I/O ports
VDD-0.7
VDD-0.7
V
V
IOH = -5.4 mA, VDD = 4.5V
IOH = -1.0 mA, VDD = 4.5V,
RC option only
OSC2/CLKOUT
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30236B-page 130
1996 Microchip Technology Inc.
PIC16C58A
Enh. PIC16C5X
15.5
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
T
Time
2
to
mc
osc
os
MCLR
ck
cy
drt
io
CLKOUT
cycle time
device reset timer
I/O port
oscillator
OSC1
t0
T0CKI
wdt
watchdog timer
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
FIGURE 15-1: LOAD CONDITIONS - PIC16C58A
Pin
CL = 50 pF for all pins except OSC2
CL
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
VSS
1996 Microchip Technology Inc.
DS30236B-page 131
Enh. PIC16C5X
PIC16C58A
15.6
Timing Diagrams and Specifications
FIGURE 15-2: EXTERNAL CLOCK TIMING - PIC16C58A
Q4
Q3
Q4
4
Q1
Q1
Q2
OSC1
1
3
3
4
2
CLKOUT
TABLE 15-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C58A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and Section 15.3.
Parameter
No.
(1)
Sym
Characteristic
Min Typ
Max Units
Conditions
(2)
FOSC
External CLKIN Frequency
DC
DC
DC
DC
DC
DC
DC
0.1
4.0
4.0
4.0
5.0
—
—
—
—
—
—
—
—
—
—
—
—
4.0
4.0
4.0
10
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
4.0
4.0
4.0
10
(2)
Oscillator Frequency
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30236B-page 132
1996 Microchip Technology Inc.
PIC16C58A
Enh. PIC16C5X
TABLE 15-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C58A (CON’T)
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and Section 15.3.
Parameter
(1)
No.
Sym
Characteristic
Min Typ
Max Units
Conditions
RC osc mode
(2)
1
TOSC
External CLKIN Period
250
250
250
100
50
—
—
—
—
ns
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
—
ns
ns
µs
ns
ns
ns
XT osc mode
—
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
—
—
5.0
250
250
250
100
50
—
—
(2)
Oscillator Period
—
—
RC osc mode
—
10,000
250
250
250
200
—
XT osc mode
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
5.0
—
—
(3)
2
3
TCY
Instruction Cycle Time
4/FOSC
—
TosL, TosH Clock in (OSC1) Low or High Time
50*
20*
2.0*
—
—
XT oscillator
HS oscillator
LP oscillator
XT oscillator
HS oscillator
LP oscillator
—
—
—
—
4
TosR, TosF Clock in (OSC1) Rise or Fall Time
—
25*
25*
50*
—
—
—
—
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1996 Microchip Technology Inc.
DS30236B-page 133
Enh. PIC16C5X
PIC16C58A
FIGURE 15-3: CLKOUT AND I/O TIMING - PIC16C58A
Q1
Q2
Q3
Q4
OSC1
10
11
CLKOUT
13
12
18
14
19
16
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 15-3: CLKOUT AND I/O TIMING REQUIREMENTS - PIC16C58A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and
Section 15.3.
Parameter
(1)
No.
Sym
Characteristic
(2)
Min
Typ
Max
Units
10
11
12
13
14
15
16
17
18
TosH2ckL
TosH2ckH
TckR
OSC1↑ to CLKOUT↓
—
15
15
5
30**
30**
15**
15**
40**
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
(2)
OSC1↑ to CLKOUT↑
—
(2)
CLKOUT rise time
—
(2)
TckF
CLKOUT fall time
—
5
(2)
CLKOUT↓ to Port out valid
TckL2ioV
TioV2ckH
TckH2ioI
TosH2ioV
TosH2ioI
—
—
—
—
—
—
(2)
Port in valid before CLKOUT↑
(2)
0.25 TCY+30*
Port in hold after CLKOUT↑
OSC1↑ (Q1 cycle) to Port out valid
0*
—
—
(3)
100*
—
OSC1↑ (Q2 cycle) to Port input invalid (I/O in
TBD
hold time)
19
TioV2osH
Port input valid to OSC1↑
TBD
—
—
ns
(I/O in setup time)
(3)
20
21
TioR
TioF
Port output rise time
—
—
10
10
25**
25**
ns
ns
(3)
Port output fall time
*
These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 15-1 for loading conditions.
DS30236B-page 134
1996 Microchip Technology Inc.
PIC16C58A
Enh. PIC16C5X
FIGURE 15-4: RESET, WATCHDOG TIMER, AND
DEVICE RESET TIMER TIMING - PIC16C58A
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 15-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16C58A
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and Section 15.3.
Parameter
No.
(1)
Sym Characteristic
Min Typ
Max Units
Conditions
30
31
TmcL MCLR Pulse Width (low)
100*
9.0*
—
—
ns VDD = 5.0V
Twdt Watchdog Timer Time-out Period
(No Prescaler)
18*
40*
ms VDD = 5.0V (Commercial)
32
34
TDRT Device Reset Timer Period
9.0*
—
18*
—
30*
ms VDD = 5.0V (Commercial)
ns
TioZ I/O Hi-impedance from MCLR Low
100*
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
1996 Microchip Technology Inc.
DS30236B-page 135
Enh. PIC16C5X
PIC16C58A
FIGURE 15-5: TIMER0 CLOCK TIMINGS - PIC16C58A
T0CKI
40
41
42
TABLE 15-5: TIMER0 CLOCK REQUIREMENTS - PIC16C58A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and
Section 15.3.
Parameter
(1)
Sym Characteristic
Min
Typ
Max Units Conditions
No.
40
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
41
42
Tt0L T0CKI Low Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
Tt0P T0CKI Period
20 or TCY + 40*
N
ns Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
DS30236B-page 136
1996 Microchip Technology Inc.
PIC16CR58A Enh. PIC16C5X
16.0 ELECTRICAL CHARACTERISTICS - PIC16CR58A
Absolute Maximum Ratings†
Ambient Temperature under bias...........................................................................................................–55°C to +125°C
Storage Temperature .............................................................................................................................–65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
(2)
Voltage on MCLR with respect to VSS ............................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
(1)
Total Power Dissipation ....................................................................................................................................800 mW
Max. Current out of VSS pin ..................................................................................................................................150 mA
Max. Current into VDD pin .....................................................................................................................................100 mA
Max. Current into an input pin (T0CKI only) ....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD)....................................................................................................................±20 mA
Output Clamp Current, IOK (V0 < 0 or V0 > VDD).............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin................................................................................................................25 mA
Max. Output Current sourced by any I/O pin...........................................................................................................20 mA
Max. Output Current sourced by a single I/O port
PORTA .........................................................................................................................................................50 mA
PORTB.......................................................................................................................................................100 mA
Max. Output Current sunk by a single I/O port
PORTA .........................................................................................................................................................50 mA
PORTB.......................................................................................................................................................100 mA
Note 1: Power Dissipation is calculated as follows: PDIS = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
Note 2: Voltage spikes below Vss at the MCLR pin, inducing currents greater than 80 mA may cause latch-up. Thus,
a series resistor of 50 to 100Ω should be used when applying a low level to the MCLR pin rather than pulling
this pin directly to Vss.
†
NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1996 Microchip Technology Inc.
DS30236B-page 137
Enh. PIC16C5X
PIC16CR58A
TABLE 16-1: CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
OSC
PIC16CR58A-04
PIC16CR58A-10
PIC16CR58A-20
PIC16LCR58A-04
RC
VDD: 3.0V to 6.25V
IDD: 2.5 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
N/A
N/A
N/A
Freq: 4.0 MHz max
XT
HS
LP
VDD: 3.0V to 6.25V
IDD: 2.5 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
N/A
N/A
N/A
N/A
Freq: 4.0 MHz max
VDD: 4.5V to 5.5V
VDD: 4.5V to 5.5V
IDD: 8.0 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
IDD: 17 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
N/A
N/A
Freq: 10 MHz max
Freq: 20 MHz max
VDD: 2.5V to 6.25V
IDD: 28 µA max at 32 kHz,
2.5V
IPD: 4.0 µA max at 2.5V,
WDT dis
N/A
N/A
Freq: 200 kHz max
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30236B-page 138
1996 Microchip Technology Inc.
PIC16CR58A Enh. PIC16C5X
16.1
DC Characteristics: PIC16CR58A-04, 10, 20 (Commercial)
PIC16CR58A-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym
Min Typ
Max
Units
Conditions
Supply Voltage
RC and XT options
HS option
VDD
3.0
4.5
6.25
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
V
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
(4)
RC and XT options
1.9
2.5
4.7
2.5
8.0
17
mA
mA
mA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
HS option
(5)
Power-Down Current
IPD
Commercial
4.0
0.25
5.0
12
4.0
14
µA
µA
µA
µA
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
Industrial
0.3
5.0
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 139
Enh. PIC16C5X
PIC16CR58A
16.2
DC Characteristics: PIC16CR58A-04E, 10E, 20E (Automotive)
DC Characteristics
Power Supply Pins
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (automotive)
(1)
Characteristic
Sym
Min Typ
Max Units
Conditions
Supply Voltage
RC and XT options
HS options
VDD
3.25
4.5
6.0
5.5
V
V
(2)
RAM Data Retention Voltage
VDR
1.5*
V
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
(4)
RC and XT options
1.9
4.8
9.0
3.3
10
20
mA
mA
mA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 16 MHz, VDD = 5.5V
HS option
(5)
Power-Down Current
IPD
5.0
0.8
22
18
µA
µA
VDD = 3.25V, WDT enabled
VDD = 3.25V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design
guidance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30236B-page 140
1996 Microchip Technology Inc.
PIC16CR58A Enh. PIC16C5X
16.3
DC Characteristics: PIC16LCR58A-04 (Commercial)
PIC16LCR58A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
(1)
Characteristic
Sym
Min Typ
Max
Units
Conditions
Supply Voltage
VDD
VDR
2.5
6.25
V
V
V
(2)
RAM Data Retention Voltage
1.5*
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD 0.05*
IDD
V/ms See Section 7.4 for details on
Power-on Reset
(3)
Supply Current
Commercial
12
15
28
37
µA
µA
FOSC = 32 kHz, VDD = 2.5V,
WDT disabled
FOSC = 32 kHz, VDD = 2.5V,
WDT disabled
Industrial
(5)
Power-Down Current
IPD
Commercial
4.0
0.25
5.0
12
4.0
14
µA
µA
µA
µA
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
Industrial
0.3
5.0
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1996 Microchip Technology Inc.
DS30236B-page 141
Enh. PIC16C5X
PIC16CR58A
16.4
DC Characteristics: PIC16CR58A-04, 10, 20, PIC16LCR58A-04 (Commercial)
PIC16CR58A-04I, 10I, 20I, PIC16LCR58A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
DC Characteristics
All Pins Except
Power Supply Pins
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 16.1 and Section 16.3.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
0.45 VDD
2.0
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
For all VDD
(5)
4.0V < VDD ≤ 5.5V
VDD > 5.5V
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
–1.0
+1.0
µA
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
–5.0
µA
µA
µA
µA
VPIN = VSS + 0.25V
(2)
0.5
0.5
0.5
+5.0
+3.0
+3.0
VPIN = VDD
T0CKI
OSC1
–3.0
–3.0
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
(3)
Output High Voltage
VOH
I/O ports
OSC2/CLKOUT
VDD –0.7
VDD –0.7
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30236B-page 142
1996 Microchip Technology Inc.
PIC16CR58A Enh. PIC16C5X
16.5
DC Characteristics: PIC16CR58A-04E, 10E, 20E (Automotive)
DC Characteristics
All Pins Except
Standard Operating Conditions (unless otherwise specified)
Operating Temperature –40°C ≤ TA ≤ +125°C
Power Supply Pins
Operating Voltage VDD range is described in Section 16.2.
(1)
Characteristic
Sym
Min
Typ
Max
Units
Conditions
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
Pin at hi-impedance
(4)
RC option only
XT, HS and LP options
Input High Voltage
I/O ports
VIH
(5)
0.45 VDD
2.0
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
For all VDD
(5)
4.0V < VDD ≤ 5.5V
VDD > 5.5V
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
(4)
RC option only
XT, HS and LP options
Hysteresis of Schmitt
Trigger inputs
VHYS 0.15VDD*
V
(3)
Input Leakage Current
IIL
For VDD ≤ 5.5V
I/O ports
–1.0
+1.0
µA
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
(2)
MCLR
–5.0
µA
µA
µA
µA
VPIN = VSS + 0.25V
(2)
0.5
0.5
0.5
+5.0
+3.0
+3.0
VPIN = VDD
T0CKI
OSC1
–3.0
–3.0
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
(3)
Output High Voltage
VOH
I/O ports
OSC2/CLKOUT
VDD –0.7
VDD –0.7
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1996 Microchip Technology Inc.
DS30236B-page 143
Enh. PIC16C5X
PIC16CR58A
16.6
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
T
Time
2
to
mc
osc
os
MCLR
ck
cy
drt
io
CLKOUT
cycle time
device reset timer
I/O port
oscillator
OSC1
t0
T0CKI
wdt
watchdog timer
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (Hi-impedance)
Low
Valid
L
Hi-impedance
FIGURE 16-1: LOAD CONDITIONS
Pin
CL = 50 pF for all pins except OSC2
CL
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
VSS
DS30236B-page 144
1996 Microchip Technology Inc.
PIC16CR58A Enh. PIC16C5X
16.7
Timing Diagrams and Specifications
FIGURE 16-2: EXTERNAL CLOCK TIMING - PIC16CR58A
Q4
Q3
Q4
4
Q1
Q1
Q2
OSC1
1
3
3
4
2
CLKOUT
TABLE 16-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR58A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and Section 16.3.
Parameter
No.
(1)
Sym
Characteristic
Min Typ
Max Units
Conditions
(2)
FOSC
External CLKIN Frequency
DC
DC
DC
DC
DC
DC
DC
0.1
4.0
4.0
4.0
5.0
—
—
—
—
—
—
—
—
—
—
—
—
4.0
4.0
4.0
10
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
4.0
4.0
4.0
10
(2)
Oscillator Frequency
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode (04)
MHz HS osc mode (10)
MHz HS osc mode (20)
kHz LP osc mode
20
200
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1996 Microchip Technology Inc.
DS30236B-page 145
Enh. PIC16C5X
PIC16CR58A
TABLE 16-2: EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR58A (CON’T)
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and Section 16.3.
Parameter
(1)
No.
Sym
Characteristic
Min Typ
Max Units
Conditions
RC osc mode
(2)
1
TOSC
External CLKIN Period
250
250
250
100
50
—
—
—
—
ns
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
µs
—
ns
ns
µs
ns
ns
ns
XT osc mode
—
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
—
—
5.0
250
250
250
100
50
—
—
(2)
Oscillator Period
—
—
RC osc mode
—
10,000
250
250
250
200
—
XT osc mode
—
HS osc mode (04)
HS osc mode (10)
HS osc mode (20)
LP osc mode
—
—
5.0
—
—
(3)
2
3
TCY
Instruction Cycle Time
4/FOSC
—
TosL, TosH Clock in (OSC1) Low or High Time
50*
20*
2.0*
—
—
XT oscillator
HS oscillator
LP oscillator
XT oscillator
HS oscillator
LP oscillator
—
—
—
—
4
TosR, TosF Clock in (OSC1) Rise or Fall Time
—
25*
25*
50*
—
—
—
—
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30236B-page 146
1996 Microchip Technology Inc.
PIC16CR58A Enh. PIC16C5X
FIGURE 16-3: CLKOUT AND I/O TIMING - PIC16CR58A
Q1
Q2
Q3
Q4
OSC1
10
11
CLKOUT
12
13
18
19
16
14
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 16-3: CLKOUT AND I/O TIMING REQUIREMENTS - PIC16CR58A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and
Section 16.3.
Parameter
(1)
No.
Sym
Characteristic
(2)
Min
Typ
Max
Units
10
11
12
13
14
15
16
17
18
TosH2ckL
TosH2ckH
TckR
OSC1↑ to CLKOUT↓
—
15
15
5.0
5.0
—
30**
30**
15**
15**
40**
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
(2)
OSC1↑ to CLKOUT↑
—
(2)
CLKOUT rise time
—
(2)
TckF
CLKOUT fall time
—
(2)
CLKOUT↓ to Port out valid
TckL2ioV
TioV2ckH
TckH2ioI
TosH2ioV
TosH2ioI
—
(2)
Port in valid before CLKOUT↑
(2)
0.25 TCY+30*
—
Port in hold after CLKOUT↑
OSC1↑ (Q1 cycle) to Port out valid
0*
—
—
—
(3)
—
100*
—
OSC1↑ (Q2 cycle) to Port input invalid (I/O in
TBD
—
hold time)
19
TioV2osH
Port input valid to OSC1↑
TBD
—
—
ns
(I/O in setup time)
(3)
20
21
TioR
TioF
Port output rise time
—
—
10
10
25**
25**
ns
ns
(3)
Port output fall time
*
These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 16-1 for loading conditions.
1996 Microchip Technology Inc.
DS30236B-page 147
Enh. PIC16C5X
PIC16CR58A
FIGURE 16-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER TIMING - PIC16CR58A
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 16-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16CR58A
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and Section 16.3.
Parameter
No.
(1)
Sym Characteristic
Min Typ
Max Units
Conditions
30
31
TmcL MCLR Pulse Width (low)
1.0*
7.0*
—
—
µs VDD = 5.0V
Twdt Watchdog Timer Time-out Period
(No Prescaler)
18*
40*
ms VDD = 5.0V (Commercial)
32
34
TDRT Device Reset Timer Period
7.0*
—
18*
—
30*
ms VDD = 5.0V (Commercial)
TioZ I/O Hi-impedance from MCLR Low
1.0*
µs
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30236B-page 148
1996 Microchip Technology Inc.
PIC16CR58A Enh. PIC16C5X
FIGURE 16-5: TIMER0 CLOCK TIMINGS - PIC16CR58A
T0CKI
40
41
42
TABLE 16-5: TIMER0 CLOCK REQUIREMENTS - PIC16CR58A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial),
–40°C ≤ TA ≤ +85°C (industrial),
–40°C ≤ TA ≤ +125°C (automotive)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and
Section 16.3.
Parameter
(1)
Sym Characteristic
Min
Typ
Max Units Conditions
No.
40
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
41
42
Tt0L T0CKI Low Pulse Width - No Prescaler
- With Prescaler
0.5 TCY + 20*
10*
Tt0P T0CKI Period
20 or TCY + 40*
N
ns Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
*
These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
1996 Microchip Technology Inc.
DS30236B-page 149
Enh. PIC16C5X
PIC16CR58A
NOTES:
DS30236B-page 150
1996 Microchip Technology Inc.
All Enh. PIC16C5X, Except PIC16CR54A
Enh. PIC16C5X
17.0 DC AND AC CHARACTERISTICS - ALL ENH. PIC16C5X,
EXCEPT PIC16CR54A
The graphs and tables provided in this section are for design guidance and are not tested or guaranteed. In some
graphs or tables the data presented are outside specified operating range (e.g., outside specified VDD range). This is
for information only and devices will operate properly only within the specified range.
The data presented in this section is a statistical summary of data collected on units from different lots over a period of
time. “Typical” represents the mean of the distribution while “max” or “min” represents (mean + 3σ) and (mean – 3σ)
respectively, where σ is standard deviation.
FIGURE 17-1: TYPICAL RC OSCILLATOR FREQUENCY vs.TEMPERATURE
FOSC
Frequency normalized to +25°C
FOSC (25°C)
1.10
Rext ≥ 10 kΩ
Cext = 100 pF
1.08
1.06
1.04
1.02
1.00
0.98
0.96
0.94
VDD = 5.5 V
VDD = 3.5 V
0.92
0.90
0.88
0
10
20
25
30
40
50
60
70
T(°C)
TABLE 17-1: RC OSCILLATOR FREQUENCIES
Average
Fosc @ 5 V, 25°C
Cext
Rext
20 pF
3.3 k
5 k
4.973 MHz
3.82 MHz
2.22 MHz
262.15 kHz
1.63 MHz
1.19 MHz
684.64 kHz
71.56 kHz
660 kHz
± 27%
± 21%
± 21%
± 31%
± 13%
± 13%
± 18%
± 25%
± 10%
± 14%
± 15%
± 19%
10 k
100 k
3.3 k
5 k
100 pF
300 pF
10 k
100 k
3.3 k
5.0 k
10 k
160 k
484.1 kHz
267.63 kHz
29.44 kHz
The frequencies are measured on DIP packages.
The percentage variation indicated here is part-to-part variation due to normal process distribution. The variation
indicated is ±3 standard deviation from average value for VDD = 5 V.
1996 Microchip Technology Inc.
DS30286B-page 151
Enh. PIC16C5X
All Enh. PIC16C5X, Except PIC16CR54A
FIGURE 17-2: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 20PF
6.00
R=3.3K
5.00
R=5.0K
4.00
3.00
R=10K
2.00
Cext=20pF, T=25C
1.00
R=100K
0.00
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
FIGURE 17-3: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 100 PF
1.80
R=3.3K
1.60
1.40
R=5.0K
1.20
1.00
0.80
0.60
R=10K
Cext=100pF, T=25C
0.40
0.20
R=100K
0.00
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
DS30286B-page 152
1996 Microchip Technology Inc.
All Enh. PIC16C5X, Except PIC16CR54A
Enh. PIC16C5X
FIGURE 17-4: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 300 PF
700.00
R=3.3K
600.00
500.00
R=5.0K
400.00
300.00
R=10K
200.00
Cext=300pF, T=25C
100.00
R=100K
0.00
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
1996 Microchip Technology Inc.
DS30286B-page 153
Enh. PIC16C5X
All Enh. PIC16C5X, Except PIC16CR54A
FIGURE 17-5: TYPICAL IPD vs. VDD, WATCHDOG DISABLED (25°C)
2.5
2
1.5
1
0.5
0
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
FIGURE 17-6: MAXIMUM IPD vs. VDD, WATCHDOG DISABLED (-40°C TO +85°C)
60.00
50.00
85C
40.00
30.00
20.00
10.00
70C
0C
-40C
0.00
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
DS30286B-page 154
1996 Microchip Technology Inc.
All Enh. PIC16C5X, Except PIC16CR54A
Enh. PIC16C5X
FIGURE 17-7: TYPICAL IPD vs. VDD, WATCHDOG ENABLED (25°C)
25.00
20.00
15.00
10.00
5.00
0.00
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
FIGURE 17-8: MAXIMUM IPD vs. VDD, WATCHDOG ENABLED (-40°C TO +85°C)
35.00
-40C
30.00
25.00
0C
70C
85C
20.00
15.00
10.00
5.00
0.00
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
1996 Microchip Technology Inc.
DS30286B-page 155
Enh. PIC16C5X
All Enh. PIC16C5X, Except PIC16CR54A
FIGURE 17-9: VTH (INPUT THRESHOLD VOLTAGE) OF I/O PINS vs. VDD
2.00
1.80
1.60
1.40
1.20
1.00
0.80
0.60
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (Volts)
FIGURE 17-10: VIH, VIL OF MCLR,T0CKI AND OSC1 (IN RC MODE) vs. VDD
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
2.5
3.0
3.5
4.0
4.5
VDD (Volts)
5.0
5.5
6.0
Note: These input pins have Schmitt Trigger input buffers.
FIGURE 17-11: VTH (INPUT THRESHOLD VOLTAGE) OF OSC1 INPUT
(IN XT, HS, AND LP MODES) vs. VDD
3.4
3.2
3.0
2.8
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (Volts)
DS30286B-page 156
1996 Microchip Technology Inc.
All Enh. PIC16C5X, Except PIC16CR54A
Enh. PIC16C5X
FIGURE 17-12: TYPICAL IDD vs. FREQUENCY (WDT DIS, RC MODE @ 20PF, 25°C)
10000
1000
6.0V
5.5V
5.0V
100
4.5V
4.0V
3.5V
3.0V
2.5V
10
100000
1000000
10000000
Freq(Hz)
FIGURE 17-13: MAXIMUM IDD vs. FREQUENCY (WDT DIS, RC MODE @ 20PF, -40°C TO +85°C)
10000
1000
6.0V
5.5V
4.5V
4.0V
3.5V
3.0V
2.5V
100
10
100000
1000000
10000000
Freq(Hz)
1996 Microchip Technology Inc.
DS30286B-page 157
Enh. PIC16C5X
All Enh. PIC16C5X, Except PIC16CR54A
FIGURE 17-14: TYPICAL IDD vs. FREQUENCY (WDT DIS, RC MODE @ 100PF, 25°C)
10000
1000
6.0V
5.5V
5.0V
100
4.5V
4.0V
3.5V
3.0V
2.5V
10
10000
100000
1000000
10000000
Freq(Hz)
FIGURE 17-15: MAXIMUM IDD vs. FREQUENCY (WDT DIS, RC MODE @ 100PF, -40°C TO +85°C)
10000
1000
6.0V
5.5V
5.0V
100
4.5V
4.0V
3.5V
3.0V
2.5V
10
10000
100000
1000000
10000000
Freq(Hz)
DS30286B-page 158
1996 Microchip Technology Inc.
All Enh. PIC16C5X, Except PIC16CR54A
Enh. PIC16C5X
FIGURE 17-16: TYPICAL IDD vs. FREQUENCY (WDT DIS, RC MODE @ 300PF, 25°C)
10000
1000
6.0V
100
5.5V
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
10
10000
100000
1000000
Freq(Hz)
FIGURE 17-17: MAXIMUM IDD vs. FREQUENCY (WDT DIS, RC MODE @ 300PF, -40°C TO +85°C)
10000
1000
6.0V
5.5V
5.0V
4.5V
100
4.0V
3.5V
3.0V
2.5V
10
10000
100000
1000000
Freq(Hz)
1996 Microchip Technology Inc.
DS30286B-page 159
Enh. PIC16C5X
All Enh. PIC16C5X, Except PIC16CR54A
FIGURE 17-18: WDT TIMER TIME-OUT
PERIOD vs. VDD
TABLE 17-2: INPUT CAPACITANCE FOR
PIC16C54A/C58A
Typical Capacitance (pF)
Pin
50
45
40
18L PDIP
18L SOIC
RA port
RB port
5.0
4.3
5.0
4.3
MCLR
17.0
4.0
17.0
3.5
OSC1
35
OSC2/CLKOUT
T0CKI
4.3
3.5
30
3.2
2.8
Max +85°C
All capacitance values are typical at 25°C. A part-to-part
variation of ±25% (three standard deviations) should be
taken into account.
25
Max +70°C
20
Typ +25°C
15
MIn 0°C
10
MIn –40°C
5
2
3
4
5
6
7
VDD (Volts)
DS30286B-page 160
1996 Microchip Technology Inc.
All Enh. PIC16C5X, Except PIC16CR54A
Enh. PIC16C5X
FIGURE 17-19: TRANSCONDUCTANCE (gm)
OF HS OSCILLATOR vs. VDD
FIGURE 17-20: TRANSCONDUCTANCE (gm)
OF LP OSCILLATOR vs. VDD
9000
45
8000
40
Max –40°C
Max –40°C
7000
6000
35
30
5000
25
Typ +25°C
Typ +25°C
4000
3000
20
15
Min +85°C
2000
10
Min +85°C
100
0
5
0
2
3
4
5
6
7
2
3
4
5
6
7
VDD (Volts)
VDD (Volts)
FIGURE 17-21: TRANSCONDUCTANCE (gm)
OF XT OSCILLATOR vs. VDD
2500
Max –40°C
2000
1500
Typ +25°C
1000
Min +85°C
500
0
2
3
4
5
6
7
VDD (Volts)
1996 Microchip Technology Inc.
DS30286B-page 161
Enh. PIC16C5X
All Enh. PIC16C5X, Except PIC16CR54A
FIGURE 17-22: IOH vs. VOH, VDD = 3 V
FIGURE 17-24: IOL vs. VOL, VDD = 3 V
0
45
Max –40°C
40
–5
35
Min +85°C
30
25
–10
Typ +25°C
Typ +25°C
–15
20
Max –40°C
15
Min +85°C
–20
10
5
0
–25
0
0.5 1.0 1.5 2.0 2.5 3.0
VOH (Volts)
0.0
0.5 1.0 1.5 2.0 2.5 3.0
VOL (Volts)
FIGURE 17-23: IOH vs. VOH, VDD = 5 V
FIGURE 17-25: IOL vs. VOL, VDD = 5 V
90
0
Max –40°C
80
70
Min +85°C
–10
60
50
Typ +25°C
–20
Typ +25°C
40
Min +85°C
30
20
–30
Max –40°C
–40
10
0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
VOH (Volts)
0.0 0.5 1.0 1.5 2.0 2.5 3.0
VOL (Volts)
DS30286B-page 162
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
18.0 DC AND AC CHARACTERISTICS - PIC16CR54A
The graphs and tables provided in this section are for design guidance and are not tested or guaranteed. In some
graphs or tables the data presented are outside specified operating range (e.g., outside specified VDD range). This is
for information only and devices are will properly only within the specified range.
The data presented in this section is a statistical summary of data collected on units from different lots over a period of
time. “Typical” represents the mean of the distribution while “max” or “min” represents (mean + 3σ) and (mean – 3σ)
respectively, where σ is standard deviation.
FIGURE 18-1: TYPICAL RC OSCILLATOR FREQUENCY vs.TEMPERATURE
FOSC
Frequency normalized to +25°C
FOSC (25°C)
1.10
Rext ≥ 10 kΩ
Cext = 100 pF
1.08
1.06
1.04
1.02
1.00
0.98
0.96
0.94
VDD = 5.5V
VDD = 3.5V
0.92
0.90
0.88
0
10
20
25
30
40
50
60
70
T(°C)
TABLE 18-1: RC OSCILLATOR FREQUENCIES
Average
Fosc @ 5V, 25°C
Cext
Rext
Part to Part Variation
20 pF
3.3 k
5 k
6.02 MHz
4.06 MHz
2.47 MHz
261 kHz
1.82 MHz
1.28 MHz
715 kHz
72.4 kHz
712.4 kHz
508 kHz
278 kHz
28 kHz
± 28%
± 25%
± 24%
± 39%
± 18%
± 21%
± 18%
± 28%
± 14%
± 13%
± 13%
± 23%
10 k
100 k
3.3 k
5 k
100 pF
300 pF
10 k
100 k
3.3 k
5 k
10 k
100 k
Measured on DIP packages.
The percentage variation indicated here is part-to-part variation due to normal process distribution. The variation
indicated is ±3 standard deviation from average value for full VDD range.
1996 Microchip Technology Inc.
DS30236B-page 163
Enh. PIC16C5X
PIC16CR54A
FIGURE 18-2: TYPICAL RC OSCILLATOR
FREQUENCY vs. VDD,
FIGURE 18-3: TYPICAL RC OSCILLATOR
FREQUENCY vs. VDD,
CEXT = 20 PF
CEXT = 100 PF
6.5
2.0
R = 3.3k
R = 3.3k
6.0
1.8
1.6
5.5
5.0
1.4
R = 5k
4.5
1.2
1.0
R = 5k
4.0
3.5
3.0
0.8
R = 10k
0.6
Measured on DIP Packages, T = 25˚C
R = 10k
2.5
0.4
2.0
0.2
R = 100k
1.5
0.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
Measured on DIP Packages, T = 25˚C
VDD (Volts)
1.0
0.5
R = 100k
0.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (Volts)
DS30236B-page 164
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
FIGURE 18-4: TYPICAL RC OSCILLATOR
FREQUENCY vs. VDD,
FIGURE 18-5: TYPICAL IPD vs. VDD,
WATCHDOG ENABLED
CEXT = 300 PF
0.8
10
R = 3.3k
0.7
T = 25˚C
0.6
1.0
R = 5k
0.5
0.4
0.1
R = 10k
0.3
0.2
Measured on DIP Packages, T = 25˚C
0.01
0.1
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
R = 100k
VDD (Volts)
0.0
2.5 3.0 3.5 4.0 4.5 5.0 5.5
6.0
VDD (Volts)
FIGURE 18-6: MAXIMUM IPD vs. VDD,
WATCHDOG ENABLED
35
30
–40°C
25
20
15
10
+85°C
5
0
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VDD (Volts)
1996 Microchip Technology Inc.
DS30236B-page 165
Enh. PIC16C5X
PIC16CR54A
FIGURE 18-7: VTH (INPUT THRESHOLD VOLTAGE) OF I/O PINS vs. VDD
2.00
1.80
1.60
1.40
1.20
1.00
0.80
0.60
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (Volts)
FIGURE 18-8: VIH, VIL OF MCLR,T0CKI AND OSC1 (IN RC MODE) vs. VDD
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
2.5
3.0
3.5
4.0
4.5
VDD (Volts)
5.0
5.5
6.0
Note: These input pins have Schmitt Trigger input buffers.
FIGURE 18-9: VTH (INPUT THRESHOLD VOLTAGE) OF OSC1 INPUT
(IN XT, HS, AND LP MODES) vs. VDD
3.4
3.2
3.0
2.8
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (Volts)
DS30236B-page 166
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
FIGURE 18-10: TYPICAL IDD vs. FREQUENCY (EXTERNAL CLOCK 25°C)
10
1.0
0.1
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
0.01
0.001
10k
100k
1M
10M
External Clock Frequency (Hz)
1996 Microchip Technology Inc.
DS30236B-page 167
Enh. PIC16C5X
PIC16CR54A
FIGURE 18-11: MAXIMUM IDD vs. FREQUENCY (EXTERNAL CLOCK –40°C TO +85°C)
10000
1000
100
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
10
10k
100k
1M
10M
External Clock Frequency (Hz)
DS30236B-page 168
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
FIGURE 18-12: WDT TIMER TIME-OUT
PERIOD vs. VDD
FIGURE 18-13: TRANSCONDUCTANCE (gm)
OF HS OSCILLATOR vs. VDD
50
45
40
9000
8000
7000
35
6000
Max –40°C
30
5000
Max +85°C
Typ +25°C
Typ +25°C
25
4000
Max +70°C
Min +85°C
20
3000
15
2000
100
0
MIn 0°C
10
MIn –40°C
5
2
3
4
5
6
7
2
3
4
5
6
7
VDD (Volts)
VDD (Volts)
1996 Microchip Technology Inc.
DS30236B-page 169
Enh. PIC16C5X
PIC16CR54A
FIGURE 18-14: TRANSCONDUCTANCE (gm)
OF LP OSCILLATOR vs. VDD
FIGURE 18-16: IOH vs. VOH, VDD = 3 V
45
0
Max –40°C
40
–5
35
30
Min +85°C
–10
Typ +25°C
Typ +25°C
25
20
15
–15
Max –40°C
Min +85°C
–20
10
5
0
–25
0.0 0.5 1.0
1.5 2.0
2.5 3.0
2
3
4
5
6
7
VOH (Volts)
VDD (Volts)
FIGURE 18-17: IOH vs. VOH, VDD = 5 V
FIGURE 18-15: TRANSCONDUCTANCE (gm)
OF XT OSCILLATOR vs. VDD
2500
0
–5
2000
Max –40°C
–10
Min +85°C
–15
1500
–20
Typ +25°C
Typ +25°C
1000
–25
–30
Min +85°C
500
Max –40°C
–35
–40
0
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
2
3
4
5
6
7
VOH (Volts)
VDD (Volts)
DS30236B-page 170
1996 Microchip Technology Inc.
PIC16CR54A Enh. PIC16C5X
FIGURE 18-18: IOL vs. VOL, VDD = 3 V
FIGURE 18-19: IOL vs. VOL, VDD = 5 V
45
90
40
35
Max –40°C
80
70
Max –40°C
30
25
60
50
Typ +25°C
Min +85°C
Typ +25°C
Min +85°C
20
40
15
10
30
20
5
0
10
0
0.0
0.5 1.0 1.5 2.0 2.5 3.0
VOL (Volts)
0.0
0.5 1.0 1.5 2.0 2.5 3.0
VOL (Volts)
TABLE 18-2: INPUT CAPACITANCE FOR
PIC16CR54A
Typical Capacitance (pF)
Pin
18L PDIP
18L SOIC
RA, RB port
MCLR
5.0
2.0
4.0
3.2
4.3
2.0
3.5
2.8
OSC1, OSC2/CLKOUT
T0CKI
All capacitance values are typical at 25°C. A part-to-part
variation of ±25% (three standard deviations) should be
taken into account.
1996 Microchip Technology Inc.
DS30236B-page 171
Enh. PIC16C5X
PIC16CR54A
NOTES:
DS30236B-page 172
1996 Microchip Technology Inc.
Enhanced PIC16C5X
19.0 PACKAGING INFORMATION
19.1
Package Marking Information
18-Lead PDIP
Example
MMMMMMMMMMMMXXX
MMMMMMMMXXXXXXX
PIC16LCR56-
40I/P456
AABB CDE
9523 CBA
28-Lead Skinny PDIP (.300")
Example
MMMMMMMMMMMMMMMMM
XXXXXXXXXXXXXXXXX
PIC16CR58A-
04I/P456
AABB CDE
9523 CBA
28-Lead PDIP (.600")
Example
MMMMMMMMMMMMXXX
MMMMMMMMXXXXXXX
XXXXXXXXXXXXXXX
AABB CDE
PIC16C58B-
10I/P126
9542 CDA
Legend: MM...M Microchip part number information
XX...X Customer specific information*
AA
BB
C
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Facility code of the plant at which wafer is manufactured
C = Chandler, Arizona, U.S.A.,
S = Tempe, Arizona, U.S.A.
D
E
Mask revision number
Assembly code of the plant or country of origin in which
part was assembled
Note: In the event the full Microchip part number cannot be marked on one line,
it will be carried over to the next line thus limiting the number of available
characters for customer specific information.
*
Standard OTP marking consists of Microchip part number, year code, week
code, facility code, mask rev#, and assembly code. For OTP marking
beyond this, certain price adders apply. Please check with your Microchip
Sales Office. For QTP devices, any special marking adders are included in
QTP price.
1996 Microchip Technology Inc.
DS30236B-page 173
Enhanced PIC16C5X
18-Lead SOIC
Example
MMMMMMMMM
XXXXXXXXX
PIC16C54A-
10I/S0218
AABB CDE
9518 CDK
28-Lead SOIC
Example
MMMMMMMMMMMMMMMMMMXX
XXXXXXXXXXXXXXXXXXXX
PIC16CR57A-20/SO301
AABB CDE
9515 CBK
20-Lead SSOP
Example
MMMMMMMM
XXXXXXXX
AABB CDE
PIC16C54A
10I/218
9520 CBP
28-Lead SSOP
Example
MMMMMMMMMMMM
XXXXXXXXXXXX
PIC16CR57B-
20/SS123
AABB CDE
9525 CBK
Legend: MM...M Microchip part number information
XX...X Customer specific information*
AA
BB
C
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Facility code of the plant at which wafer is manufactured
C = Chandler, Arizona, U.S.A.,
S = Tempe, Arizona, U.S.A.
D
E
Mask revision number
Assembly code of the plant or country of origin in which
part was assembled
Note: In the event the full Microchip part number cannot be marked on one line,
it will be carried over to the next line thus limiting the number of available
characters for customer specific information.
*
Standard OTP marking consists of Microchip part number, year code, week
code, facility code, mask rev#, and assembly code. For OTP marking
beyond this, certain price adders apply. Please check with your Microchip
Sales Office. For QTP devices, any special marking adders are included in
QTP price.
DS30236B-page 174
1996 Microchip Technology Inc.
Enhanced PIC16C5X
18-Lead CERDIP Windowed
Example
MMMMMMMM
MMMMMMMM
AABB CDE
PIC16C54A
/JW
9501 CBA
28-Lead CERDIP Skinny Windowed
Example
MMMMMMMMMMMMMM
XXXXXXXXXXXXXX
AABBCDE
PIC16C58A
/JW
9338 CCT
28-Lead CERDIP Windowed
Example
MMMMMMMMMM
MMMMMM
PIC16C58A
/JW
AABB CDE
9538 CBA
Legend: MM...M Microchip part number information
XX...X Customer specific information*
AA
BB
C
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Facility code of the plant at which wafer is manufactured
C = Chandler, Arizona, U.S.A.,
S = Tempe, Arizona, U.S.A.
D
E
Mask revision number
Assembly code of the plant or country of origin in which
part was assembled
Note: In the event the full Microchip part number cannot be marked on one line,
it will be carried over to the next line thus limiting the number of available
characters for customer specific information.
*
Standard OTP marking consists of Microchip part number, year code, week
code, facility code, mask rev#, and assembly code. For OTP marking
beyond this, certain price adders apply. Please check with your Microchip
Sales Office. For QTP devices, any special marking adders are included in
QTP price.
1996 Microchip Technology Inc.
DS30236B-page 175
Enhanced PIC16C5X
19.2
18-Lead Plastic Dual In-Line (PDIP) - 300 mil
N
α
C
E1
E
eA
eB
Pin No. 1
Indicator
Area
D
S
S1
e1
Base
Plane
Seating
Plane
L
B1
B
A
A2
A1
D1
Package Group: Plastic Dual In-Line (PLA)
Millimeters
Inches
Symbol
Min
Max
Notes
Min
Max
Notes
α
0°
10°
4.064
–
0°
10°
0.160
–
A
–
–
A1
A2
B
0.381
3.048
0.355
1.524
0.203
22.479
20.320
7.620
6.096
2.489
7.620
7.874
3.048
18
0.015
0.120
0.014
0.060
0.008
0.885
0.800
0.300
0.240
0.098
0.300
0.310
0.120
18
3.810
0.559
1.524
0.381
23.495
20.320
8.255
7.112
2.591
7.620
9.906
3.556
18
0.150
0.022
0.060
0.015
0.925
0.800
0.325
0.280
0.102
0.300
0.390
0.140
18
B1
C
Reference
Typical
Reference
Typical
D
D1
E
Reference
Reference
E1
e1
eA
eB
L
Typical
Typical
Reference
Reference
N
S
0.889
0.127
–
0.035
0.005
–
S1
–
–
DS30236B-page 176
1996 Microchip Technology Inc.
Enhanced PIC16C5X
19.3
28-Lead Plastic Dual In-Line (PDIP) - 300 mil
N
α
E1
E
C
eA
eB
Pin No. 1
Indicator
Area
B2
B1
D
S
Base
Plane
Seating
Plane
L
Detail A
B
Detail A
B3
A
A2
A1
e1
D1
Package Group: Plastic Dual In-Line (PLA)
Millimeters
Inches
Max
Symbol
Min
Max
Notes
Min
Notes
α
0°
10°
4.572
–
0°
10°
A
3.632
0.381
3.175
0.406
1.016
0.762
0.203
0.203
0.143
0.015
0.125
0.016
0.040
0.030
0.008
0.008
1.385
1.300
0.310
0.280
0.100
0.310
0.320
0.125
28
0.180
–
A1
A2
B
3.556
0.559
1.651
1.016
0.508
0.331
35.179
33.020
8.382
7.493
2.540
7.874
9.652
3.683
-
0.140
0.022
0.065
0.040
0.020
0.013
1.395
1.300
0.330
0.295
0.100
0.310
0.380
0.145
-
B1
B2
B3
C
Typical
4 places
4 places
Typical
Typical
4 places
4 places
Typical
D
34.163
33.020
7.874
7.112
2.540
7.874
8.128
3.175
28
D1
E
Reference
Reference
E1
e1
eA
eB
L
Typical
Typical
Reference
Reference
N
S
0.584
1.220
0.023
0.048
1996 Microchip Technology Inc.
DS30236B-page 177
Enhanced PIC16C5X
19.4
28-Lead Plastic Dual In-Line (PDIP) - 600 mil
N
α
E1
E
C
eA
eB
Pin No. 1
Indicator
Area
D
S
S1
e1
Base
Plane
Seating
Plane
L
B1
B
A
A2
A1
D1
Package Group: Plastic Dual In-Line (PLA)
Millimeters
Inches
Symbol
Min
Max
Notes
Min
Max
Notes
α
0°
10°
5.080
–
0°
10°
0.200
–
A
–
–
A1
A2
B
0.508
3.175
0.355
1.270
0.203
0.020
0.125
0.014
0.050
0.008
1.380
1.300
0.600
0.505
0.098
0.600
0.600
0.115
28
4.064
0.559
1.778
0.381
37.084
33.020
15.875
13.970
2.591
15.240
17.272
3.683
28
0.160
0.022
0.070
0.015
1.460
1.300
0.625
0.550
0.102
0.600
0.680
0.145
28
B1
C
Typical
Typical
Typical
Typical
D
35.052
33.020
15.240
12.827
2.489
15.240
15.240
2.921
28
D1
E
Reference
Reference
E1
e1
eA
eB
L
Typical
Typical
Reference
Reference
N
S
0.889
0.508
–
0.035
0.020
–
S1
–
–
DS30236B-page 178
1996 Microchip Technology Inc.
Enhanced PIC16C5X
19.5
18-Lead Plastic Surface Mount (SOIC) - 300 mil
e
B
h x 45°
N
Index
Area
E
H
α
C
Chamfer
h x 45°
L
1
2
3
D
Base
Plane
CP
Seating
Plane
A1
A
Package Group: Plastic SOIC (SO)
Millimeters
Max
Inches
Max
Symbol
Min
0°
Notes
Min
Notes
α
A
8°
0°
8°
2.362
0.101
0.355
0.241
11.353
7.416
1.270
10.007
0.381
0.406
18
2.642
0.300
0.483
0.318
11.735
7.595
1.270
10.643
0.762
1.143
18
0.093
0.004
0.014
0.009
0.447
0.292
0.050
0.394
0.015
0.016
18
0.104
0.012
0.019
0.013
0.462
0.299
0.050
0.419
0.030
0.045
18
A1
B
C
D
E
e
Reference
Reference
H
h
L
N
CP
–
0.102
–
0.004
1996 Microchip Technology Inc.
DS30236B-page 179
Enhanced PIC16C5X
19.6
28-Lead Plastic Surface Mount (SOIC) - 300 mil
e
B
h x 45°
N
Index
Area
E
H
α
C
Chamfer
h x 45°
L
1
2
3
D
Base
Plane
CP
Seating
Plane
A1
A
Package Group: Plastic SOIC (SO)
Millimeters
Max
Inches
Symbol
Min
0°
Notes
Min
Max
Notes
α
A
8°
0°
8°
2.362
0.101
0.355
0.241
17.703
7.416
1.270
10.007
0.381
0.406
28
2.642
0.300
0.483
0.318
18.085
7.595
1.270
10.643
0.762
1.143
28
0.093
0.004
0.014
0.009
0.697
0.292
0.050
0.394
0.015
0.016
28
0.104
0.012
0.019
0.013
0.712
0.299
0.050
0.419
0.030
0.045
28
A1
B
C
D
E
e
Typical
Typical
H
h
L
N
CP
–
0.102
–
0.004
DS30236B-page 180
1996 Microchip Technology Inc.
Enhanced PIC16C5X
19.7
20-Lead Plastic Surface Mount (SSOP) - 209 mil
N
Index
area
E
H
α
C
L
1 2 3
e
B
A
Base plane
CP
Seating plane
D
A1
Package Group: Plastic SSOP
Millimeters
Max
Inches
Max
Symbol
Min
Notes
Min
Notes
α
A
0°
8°
0°
8°
1.730
0.050
0.250
0.130
7.070
5.200
0.650
7.650
0.550
20
1.990
0.210
0.380
0.220
7.330
5.380
0.650
7.900
0.950
20
0.068
0.002
0.010
0.005
0.278
0.205
0.026
0.301
0.022
20
0.078
0.008
0.015
0.009
0.289
0.212
0.026
0.311
0.037
20
A1
B
C
D
E
e
Reference
Reference
H
L
N
CP
-
0.102
-
0.004
1996 Microchip Technology Inc.
DS30236B-page 181
Enhanced PIC16C5X
19.8
28-Lead Plastic Surface Mount (SSOP) - 209 mil
N
Index
area
E
H
α
C
L
1 2 3
e
B
A
Base plane
CP
Seating plane
D
A1
Package Group: Plastic SSOP
Millimeters
Max
Inches
Max
Symbol
Min
Notes
Min
Notes
α
A
0°
8°
0°
8°
1.730
0.050
0.250
0.130
10.070
5.200
0.650
7.650
0.550
28
1.990
0.210
0.380
0.220
10.330
5.380
0.650
7.900
0.950
28
0.068
0.002
0.010
0.005
0.396
0.205
0.026
0.301
0.022
28
0.078
0.008
0.015
0.009
0.407
0.212
0.026
0.311
0.037
28
A1
B
C
D
E
e
Reference
Reference
H
L
N
CP
-
0.102
-
0.004
DS30236B-page 182
1996 Microchip Technology Inc.
Enhanced PIC16C5X
19.9
18-Lead Ceramic Dual In-Line (CERDIP) with Window - 300 mil
N
α
C
E1
E
eA
eB
Pin No. 1
Indicator
Area
D
S
S1
e1
Base
Plane
Seating
Plane
L
B1
B
A
A3
A2
A1
D1
Package Group: Ceramic Dual In-Line (CDP)
Millimeters
Inches
Max
Symbol
Min
Max
Notes
Min
Notes
α
0°
10°
0°
10°
A
—
5.080
1.7780
4.699
4.445
0.585
1.651
0.381
23.622
20.320
8.382
7.874
2.540
8.128
10.160
3.810
18
—
0.200
0.070
0.185
0.175
0.023
0.065
0.015
0.930
0.800
0.330
0.310
0.100
0.320
0.400
0.150
18
A1
A2
A3
B
0.381
3.810
3.810
0.355
1.270
0.203
22.352
20.320
7.620
5.588
2.540
7.366
7.620
3.175
18
0.015
0.150
0.150
0.014
0.050
0.008
0.880
0.800
0.300
0.220
0.100
0.290
0.300
0.125
18
B1
C
Typical
Typical
Typical
Typical
D
D1
E
Reference
Reference
E1
e1
eA
eB
L
Reference
Typical
Reference
Typical
N
S
0.508
0.381
1.397
1.270
0.020
0.015
0.055
0.050
S1
1996 Microchip Technology Inc.
DS30236B-page 183
Enhanced PIC16C5X
19.10 28-Lead Ceramic Dual In-Line (CERDIP) with Window - 600 mil
N
E1
E
α
C
Pin No. 1
Indicator
Area
eA
eB
D
S
S1
e1
Base
Plane
Seating
Plane
L
B1
B
A
A3
A2
A1
D1
Package Group: Ceramic Dual In-Line (CDP)
Millimeters
Inches
Max
Symbol
Min
Max
Notes
Min
Notes
α
0°
10°
0°
10°
A
—
5.461
1.524
4.699
4.445
0.585
1.651
0.381
37.465
33.020
15.875
15.240
2.540
15.748
18.034
3.810
28
—
0.215
0.060
0.185
0.175
0.023
0.065
0.015
1.475
1.300
0.625
0.600
0.100
0.620
0.710
0.150
28
A1
A2
A3
B
0.381
3.810
3.810
0.355
1.270
0.203
0.015
0.150
0.150
0.014
0.050
0.008
1.425
1.300
0.600
0.510
0.100
0.590
0.600
0.125
28
B1
C
Typical
Typical
Typical
Typical
D
36.195
33.020
15.240
12.954
2.540
14.986
15.240
3.175
28
D1
E
Reference
Reference
E1
e1
eA
eB
L
Typical
Typical
Reference
Reference
N
S
1.016
0.381
2.286
1.778
0.040
0.015
0.090
0.070
S1
DS30236B-page 184
1996 Microchip Technology Inc.
Enhanced PIC16C5X
APPENDIX A: COMPATIBILITY
APPENDIX B: WHAT’S NEW
To convert code written for PIC16CXX to PIC16C5X,
the user should take the following steps:
B.1
Format
The format of this data sheet has been changed to be
consistent with other product families. This ensures
that important topics are covered across all PIC16/17
families. Here is an overview list of new features:
1. Check any CALL, GOTO or instructions that
modify the PC to determine if any program
memory page select operations (PA2, PA1, PA0
bits) need to be made.
2. Revisit any computed jump operations (write to
PC or add to PC, etc.) to make sure page bits
are set properly under the new scheme.
• Data Sheet Structure / Outline
• Consistent Figures and Tables
B.2
Additions
3. Eliminate any special function register page
switching. Redefine data variables to reallocate
them.
Items that have been added to this data sheet are:
• PIC16CR54A, PIC16CR54B, PIC16CR55,
PIC16CR56, PIC16CR57B and PIC16CR58B
data
4. Verify all writes to STATUS, OPTION, and FSR
registers since these have changed.
5. Change reset vector to proper value for
processor used.
• PIC16C5X-10 data
• PIC16C5X/JW package information
6. Remove any use of the ADDLW and SUBLW
instructions.
7. Rewrite any code segments that use interrupts.
1996 Microchip Technology Inc.
DS30236B-page 185
Enhanced PIC16C5X
APPENDIX C: WHAT’S CHANGED
Changes to this version of the PIC16C5XA data sheet
are:
• Correction of the 28-lead SSOP package pin-out
• Inclusion of errata sheet information
DS30236B-page 186
1996 Microchip Technology Inc.
Enhanced PIC16C5X
APPENDIX D:PIC16/17 MICROCONTROLLERS
TABLE D-1:
PIC14XXX FAMILY OF DEVICES
1996 Microchip Technology Inc.
DS30236B-page 187
Enhanced PIC16C5X
TABLE D-2:
PIC16C5X FAMILY OF DEVICES
DS30236B-page 188
1996 Microchip Technology Inc.
Enhanced PIC16C5X
TABLE D-3:
PIC16C62X FAMILY OF DEVICES
1996 Microchip Technology Inc.
DS30236B-page 189
Enhanced PIC16C5X
TABLE D-4:
PIC16C6X FAMILY OF DEVICES
DS30236B-page 190
1996 Microchip Technology Inc.
Enhanced PIC16C5X
TABLE D-5:
PIC16C7X FAMILY OF DEVICES
1996 Microchip Technology Inc.
DS30236B-page 191
Enhanced PIC16C5X
TABLE D-6:
PIC16C8X FAMILY OF DEVICES
DS30236B-page 192
1996 Microchip Technology Inc.
Enhanced PIC16C5X
TABLE D-7:
PIC17CXX FAMILY OF DEVICES
1996 Microchip Technology Inc.
DS30236B-page 193
Enhanced PIC16C5X
D.1
Pin Compatibility
Devices that have the same package type and VDD,
VSS and MCLR pin locations are said to be pin
compatible. This allows these different devices to
operate in the same socket. Compatible devices may
only requires minor software modification to allow
proper operation in the application socket
(ex., PIC16C56 and PIC16C61 devices). Not all
devices in the same package size are pin compatible;
for example, the PIC16C62 is compatible with the
PIC16C63, but not the PIC16C55.
Pin compatibility does not mean that the devices offer
the same features. As an example, the PIC16C54 is
pin compatible with the PIC16C71, but does not have
an A/D converter, weak pull-ups on PORTB, or
interrupts.
TABLE D-8:
PIN COMPATIBLE DEVICES
Pin Compatible Devices
Package
PIC16C54, PIC16C54A,
18 pin
PIC16CR54, PIC16CR54A, PIC16CR54B,
PIC16C56, PIC16CR56,
(20 pin)
PIC16C58A, PIC16CR58A, PIC16CR58B,
PIC16C61,
PIC16C620, PIC16C621, PIC16C622,
PIC16C70, PIC16C71, PIC16C71A
PIC16C83, PIC16CR83,
PIC16C84, PIC16C84A, PIC16CR84
PIC16C55, PIC16CR55,
PIC16C57, PIC16CR57A, PIC16CR57B
28 pin
28 pin
40 pin
PIC16C62, PIC16CR62, PIC16C62A, PIC16C63,
PIC16C72, PIC16C73, PIC16C73A
PIC16C64, PIC16CR64, PIC16C64A,
PIC16C65, PIC16C65A,
PIC16C74, PIC16C74A
PIC17C42, PIC17C43, PIC17C44
40 pin
DS30236B-page 194
1996 Microchip Technology Inc.
Enhanced PIC16C5X
PIC16C8X ................................................................ 192
PIC17CXX ............................................................... 193
Features ...............................................................................1
FSR ............................................................................. 21, 33
Fuzzy Logic Dev. System (fuzzyTECH -MP) ............. 53, 57
INDEX
A
Absolute Maximum Ratings ..... 59, 71, 85, 99, 111, 125, 137
ALU ...................................................................................... 7
Applications .......................................................................... 3
Architectural Overview ......................................................... 7
Assembler .......................................................................... 56
I
I/O Interfacing .................................................................... 23
I/O Ports ............................................................................ 23
I/O Programming Considerations ...................................... 24
ID Locations ................................................................. 29, 40
INDF ............................................................................ 21, 33
Indirect Data Addressing ................................................... 21
Instruction Cycle ................................................................ 11
Instruction Flow/Pipelining ................................................. 11
Instruction Set Summary ................................................... 42
Integrated .......................................................................... 56
B
Block Diagram
On-Chip Reset Circuit ................................................ 34
PIC16C5X Series ......................................................... 8
Timer0 ........................................................................ 25
TMR0/WDT Prescaler ................................................ 28
Watchdog Timer ......................................................... 38
Brown-Out Protection Circuit ............................................. 39
L
C
Loading of PC .............................................................. 19, 20
C Compiler (MP-C) ...................................................... 53, 57
Carry .................................................................................... 7
Characteristics - DC and AC .................................... 151, 163
Clocking Scheme ............................................................... 11
Code Protection ........................................................... 29, 40
Configuration Bits ............................................................... 29
Configuration Word ............................................................ 30
PIC16C54A/CR57A/C58A ......................................... 29
PIC16CR54A/CR54B/Cr56/CR57B/CR58A/CR58B .. 30
M
MCLR ................................................................................ 33
Memory Map
PIC16C54A/CR54A/CR54B ...................................... 13
PIC16CR56 ............................................................... 13
PIC16CR57A/CR57B/C58A/CR58A/CR58B ............. 13
Memory Organization ........................................................ 13
Data Memory ............................................................. 14
Program Memory ....................................................... 13
MPASM Assembler ..................................................... 53, 56
MP-C C Compiler .............................................................. 57
MPSIM Software Simulator ......................................... 53, 57
D
Development Support ........................................................ 53
Development Systems ....................................................... 57
Development Tools ............................................................ 53
Device Drawings
O
18-Lead Ceramic Dual In-Line (CERDIP) with Window -
300 mil ..................................................................... 183
18-Lead Plastic Dual In-Line (PDIP) - 300 mil ......... 176
18-Lead Plastic Surface Mount (SOIC) - 300 mil ..... 179
20-Lead Plastic Surface Mount (SSOP) - 209 mil .... 181
28-Lead Ceramic Dual In-Line (CERDIP)
One-Time-Programmable (OTP) Devices ............................5
OPTION Register .............................................................. 18
OSC selection .................................................................... 29
Oscillator Configurations ................................................... 30
Oscillator Types
HS .............................................................................. 30
LP .............................................................................. 30
RC ............................................................................. 30
XT .............................................................................. 30
with Window - 600 mil .............................................. 184
28-Lead Plastic Dual In-Line (PDIP) - 300 mil ......... 177
28-Lead Plastic Dual In-Line (PDIP) - 600 mil ......... 178
28-Lead Plastic Surface Mount (SOIC) - 300 mil ..... 180
28-Lead Plastic Surface Mount (SSOP) - 209 mil .... 182
Device Varieties ................................................................... 5
Digit Carry ............................................................................ 7
Dynamic Data Exchange (DDE) ........................................ 53
P
Package Marking Information .......................... 173, 174, 175
Packaging Information ..................................................... 173
PC ................................................................................ 19, 33
PICDEM-1 Low-Cost PIC16/17 Demo Board .............. 53, 55
PICDEM-2 Low-Cost PIC16CXX Demo Board ............ 53, 55
PICMASTER Probes ......................................................... 54
PICMASTER System Configuration .................................. 53
PICMASTER RT In-Circuit Emulator ............................... 53
PICSTART Low-Cost Development System ............. 53, 55
Pin Compatible Devices .................................................. 194
pin diagrams .................................................................... 1, 2
Pinout Description - PIC16C54A,
E
Electrical Characteristics
PIC16C54A ................................................................ 59
PIC16C58A .............................................................. 125
PIC16CR54A ............................................................. 71
PIC16CR54B/56/58B ................................................. 85
PIC16CR57A ............................................................. 99
PIC16CR57B ........................................................... 111
PIC16CR58A ........................................................... 137
External Power-On Reset Circuit ....................................... 35
PIC16CR54A, PIC16CR54B, PIC16CR56,
PIC16C58A, PIC16CR58A, PIC16CR58B ...........................9
Pinout Description - PIC16CR57A, PIC16CR57B ............. 10
POR
F
Family of Devices
Device Reset Timer (DRT) .................................. 29, 37
PD ........................................................................ 33, 39
Power-On Reset (POR) ................................. 29, 33, 35
TO ........................................................................ 33, 39
PORTA ........................................................................ 23, 33
PIC14XXX ................................................................ 187
PIC16C5X ................................................................ 188
PIC16C62X .............................................................. 189
PIC16C6X ................................................................ 190
PIC16C7X ................................................................ 191
1996 Microchip Technology Inc.
DS30236B-page 195
Enhanced PIC16C5X
PORTB .........................................................................23, 33
PORTC .........................................................................23, 33
Power-Down Mode .............................................................40
Prescaler ............................................................................28
PRO MATE Universal Programmer ...........................53, 55
Product Identification System ...........................................201
Program Counter ................................................................19
LIST OF EXAMPLES
Example 3-1: Instruction Pipeline Flow ............................ 11
Example 4-1: Indirect Addressing..................................... 20
Example 4-2: How To Clear RAM Using Indirect
Addressing ................................................. 20
Example 5-1: Read-Modify-Write Instructions on an
I/O Port....................................................... 22
Example 6-1: Changing Prescaler (Timer0→WDT).......... 26
Example 6-2: Changing Prescaler (WDT→Timer0).......... 26
Q
Q cycles .............................................................................11
Quick-Turnaround-Production (QTP) Devices .....................5
LIST OF FIGURES
R
Figure 3-1:
Figure 3-2:
Figure 4-1:
PIC16C5X Series Block Diagram................. 8
Clock/Instruction Cycle............................... 11
PIC16C54/CR54/C55 Program
Memory Map and Stack ............................. 13
PIC16C56 Program Memory Map
RC Oscillator ......................................................................32
Read Modify Write ..............................................................24
Read Only Memory (ROM) Devices .....................................5
Register File Map
PIC16C54A/CR54A/CR54B/CR56 .............................14
PIC16C58A/CR58A/CR58B .......................................15
PIC16CR57A/CR57B .................................................15
Registers
Figure 4-2:
Figure 4-3:
and Stack ................................................... 13
PIC16C57 Program Memory Map
and Stack ................................................... 13
PIC16C54/CR54/C56 Register File Map.... 14
PIC16C55 Register File Map...................... 14
PIC16C57 Register File Map...................... 14
STATUS Register (Address:03h) ............... 16
OPTION Register ....................................... 17
Loading of PC
Figure 4-4:
Figure 4-5:
Figure 4-6:
Figure 4-7:
Figure 4-8:
Figure 4-9:
Special Function ........................................................16
Reset ............................................................................29, 33
Reset on Brown-Out ...........................................................39
S
Branch Instructions -
PIC16C54/CR54/C55................................. 18
Serialized Quick-Turnaround-Production
(SQTP ) Devices ...............................................................5
SM
Figure 4-10: Loading of PC
Branch Instructions -
PIC16C56................................................... 18
Figure 4-11: Loading of PC
Branch Instructions -
PIC16C57................................................... 18
Figure 4-12: Direct/Indirect Addressing .......................... 20
SLEEP ..........................................................................29, 40
Software Simulator (MPSIM) ..............................................57
Special Features of the CPU ..............................................29
Special Function Registers ................................................16
Stack ..................................................................................20
STATUS .........................................................................7, 33
STATUS Register ...............................................................17
Figure 5-1:
Equivalent Circuit
T
for a Single I/O Pin ..................................... 21
Successive I/O Operation........................... 22
Timer0 Block Diagram................................ 23
Electrical Structure of T0CKI Pin................ 23
Timer0 Timing:
Timer0
Figure 5-2:
Figure 6-1:
Figure 6-2:
Figure 6-3:
Switching Prescaler Assignment ................................28
Timer0 ........................................................................25
Timer0 (TMR0) Module ..............................................25
TMR0 with External Clock ..........................................27
Timing Diagrams
Internal Clock/No Prescale......................... 24
Timer0 Timing:
Figure 6-4:
and Specifications ..................66, 79, 93, 105, 119, 132, 145
Timing Parameter Symbology
and Load Conditions ..............65, 78, 92, 104, 118, 131, 144
TRIS Registers ...................................................................23
Internal Clock/Prescale 1:2 ........................ 24
Timer0 Timing With External Clock............ 25
Block Diagram of the Timer0/WDT
Prescaler .................................................... 26
Configuration Word for
PIC16C54/CR54/C55/C56/C57.................. 27
Crystal Operation or Ceramic Resonator
(HS, XT or LP OSC Configuration)............. 28
External Clock Input Operation
(HS, XT or LP OSC Configuration)............. 28
External Parallel Resonant Crystal
Figure 6-5:
Figure 6-6:
Figure 7-1:
Figure 7-2:
Figure 7-3:
Figure 7-4:
Figure 7-5:
U
UV Erasable Devices ...........................................................5
W
W ........................................................................................33
Wake-up from SLEEP ........................................................40
Watchdog Timer (WDT) ...............................................29, 37
Period .........................................................................37
Programming Considerations ....................................37
Oscillator Circuit ......................................... 29
External Series Resonant Crystal
Oscillator Circuit ......................................... 29
RC Oscillator Mode .................................... 30
Simplified Block Diagram of On-Chip
Reset Circuit............................................... 31
Electrical Structure of MCLR/VPP Pin......... 32
External Power-On Reset Circuit
Figure 7-6:
Figure 7-7:
Z
Zero bit .................................................................................7
Figure 7-8:
Figure 7-9:
(For Slow VDD Power-Up) .......................... 32
Figure 7-10: Time-Out Sequence on Power-Up
(MCLR Not Tied to VDD)............................. 33
Figure 7-11: Time-Out Sequence on Power-Up
(MCLR Tied to VDD): Fast VDD Rise Time.. 33
DS30236B-page 196
1996 Microchip Technology Inc.
Enhanced PIC16C5X
Figure 7-12: Time-Out Sequence on Power-Up (MCLR
Tied to VDD): Slow VDD Rise Time ............. 33
Figure 7-13: Watchdog Timer Block Diagram................. 35
Figure 7-14: Brown-Out Protection Circuit 1 ................... 36
Figure 7-15: Brown-Out Protection Circuit 2 ................... 36
Figure 13-1: Typical RC Oscillator Frequency
vs. Temperature ......................................... 91
Figure 13-2: Typical RC Oscillator Frequency
vs. VDD,
CEXT = 20 PF.............................................. 92
Figure 13-3: Typical RC Oscillator Frequency
vs. VDD,
Figure 8-1:
Figure 9-1:
General Format for Instructions.................. 39
PICMASTER System Configuration ........... 51
Figure 10-1: Load Conditions - PIC16C54/55/56/57....... 64
Figure 10-2: External Clock Timing
- PIC16C54/55/56/57.................................. 65
Figure 10-3: CLKOUT and I/O Timing -
PIC16C54/55/56/57 .................................... 67
Figure 10-4: Reset, Watchdog Timer, and
Device Reset Timer Timing -
CEXT = 100 PF............................................ 92
Figure 13-4: Typical RC Oscillator Frequency
vs. VDD,
CEXT = 300 PF............................................ 93
Figure 13-5: Typical IPD vs. VDD,
Watchdog Enabled..................................... 93
Figure 13-6: Maximum IPD vs. VDD,
PIC16C54/55/56/57 .................................... 68
Figure 10-5: Timer0 Clock Timings
Watchdog Enabled..................................... 93
Figure 13-7: VTH (Input Threshold Voltage) of I/O Pins
vs. VDD ....................................................... 94
Figure 13-8: VIH, VIL of MCLR, T0CKI and OSC1
(in RC Mode) vs. VDD................................. 94
Figure 13-9: VTH (Input Threshold Voltage)
of OSC1 Input (in XT, HS, and LP modes)
vs. VDD ....................................................... 94
Figure 13-10: Typical IDD vs. Frequency
(External Clock 25°C)................................. 95
Figure 13-11: Maximum IDD vs. Frequency
(External Clock –40°C to +85°C)................ 96
Figure 13-12: WDT Timer Time-out Period vs. VDD ......... 97
Figure 13-13: Transconductance (gm) OF HS Oscillator
vs. VDD ....................................................... 97
Figure 13-14: Transconductance (gm) of LP Oscillator
vs. VDD ....................................................... 98
Figure 13-15: Transconductance (gm) of XT Oscillator
vs. VDD ....................................................... 98
Figure 13-16: IOH vs. VOH, VDD = 3 V............................... 98
Figure 13-17: IOH vs. VOH, VDD = 5 V............................... 98
Figure 13-18: IOL vs. VOL, VDD = 3 V................................ 99
Figure 13-19: IOL vs. VOL, VDD = 5 V................................ 99
- PIC16C54/55/56/57.................................. 69
Figure 11-1: Typical RC Oscillator Frequency
vs. Temperature.......................................... 71
Figure 11-2: Typical RC Oscillator Frequency
vs. VDD,
CEXT = 20PF ............................................... 72
Figure 11-3: Typical RC Oscillator Frequency
vs. VDD,
CEXT = 100 PF ............................................ 72
Figure 11-4: Typical RC Oscillator Frequency
vs. VDD,
CEXT = 300 PF ............................................ 72
Figure 11-5: Typical IPD vs. VDD,
Watchdog Disabled..................................... 73
Figure 11-6: Maximum IPD vs. VDD,
Watchdog Disabled..................................... 73
Figure 11-7: Typical IPD vs. VDD,
Watchdog Enabled ..................................... 73
Figure 11-8: Maximum IPD vs. VDD,
Watchdog Enabled ..................................... 73
Figure 11-9: VTH (Input Threshold Voltage) of I/O Pins
vs. VDD........................................................ 74
Figure 11-10: VIH, VIL of MCLR, T0CKI and OSC1
(in RC Mode) vs. VDD ................................. 74
Figure 11-11: VTH (Input Threshold Voltage)
of OSC1 Input (in XT, HS, and LP modes)
vs. VDD........................................................ 74
Figure 11-12: Typical IDD vs. Frequency
(External Clock, 25°C) ................................ 75
Figure 11-13: Maximum IDD vs. Frequency
(External Clock, –40°C to +85°C)............... 75
Figure 11-14: Maximum IDD vs. Frequency
(External Clock –55°C to +125°C).............. 76
Figure 11-15: WDT Timer Time-out Period vs. VDD.......... 76
Figure 11-16: Transconductance (gm) OF HS Oscillator
vs. VDD........................................................ 76
Figure 11-17: Transconductance (gm) of LP Oscillator
vs. VDD........................................................ 77
Figure 11-18: IOH vs. VOH, VDD = 3 V............................... 77
Figure 11-19: Transconductance (gm) of XT Oscillator
vs. VDD........................................................ 77
Figure 11-20: IOH vs. VOH, VDD = 5 V............................... 77
Figure 11-21: IOL vs. VOL, VDD = 3 V................................ 78
Figure 11-22: IOL vs. VOL, VDD = 5 V................................ 78
Figure 12-1: Load Conditions.......................................... 85
Figure 12-2: External Clock Timing - PIC16CR54 .......... 86
Figure 12-3: CLKOUT and I/O Timing - PIC16CR54 ...... 88
Figure 12-4: Reset, Watchdog Timer, and Device Reset
Timer Timing - PIC16CR54 ........................ 89
Figure 12-5: Timer0 Clock Timings - PIC16CR54........... 90
1996 Microchip Technology Inc.
DS30236B-page 197
Enhanced PIC16C5X
LIST OF TABLES
Table 1-1:
Table 3-1:
Table 3-2:
Table 4-1:
Table 5-1:
Table 6-1:
Table 7-1:
PIC16C5X Family of Devices .......................4
PIC16C54/CR54/C56 Pinout Description .....9
PIC16C55/C57 Pinout Description .............10
Special Function Register Summary ..........15
Summary of Port Registers.........................21
Registers Associated With Timer0..............24
Capacitor Selection
For Ceramic Resonators -
PIC16C54/55/56/57 ....................................28
Capacitor Selection
For Crystal Oscillator - PIC16C54/55/56/5728
Capacitor Selection
For Ceramic Resonators - PIC16CR54 ......29
Capacitor Selection
Table 7-2:
Table 7-3:
Table 7-4:
For Crystal Oscillator - PIC16CR54............29
Reset Conditions for Special Registers ......31
Reset Conditions for All Registers..............31
Summary of Registers Associated with the
Watchdog Timer .........................................35
TO/PD Status After Reset...........................36
Events Affecting TO/PD Status Bits............36
OPCODE Field Descriptions.......................39
Instruction Set Summary ............................40
PICMASTER Probe Specification...............52
Development System Packages.................55
Cross Reference of Device Specs for
Table 7-5:
Table 7-6:
Table 7-7:
Table 7-8:
Table 7-9:
Table 8-1:
Table 8-2:
Table 9-1:
Table 9-2:
Table 10-1:
Oscillator Configurations (RC, XT & 10)
and Frequencies of Operation
(Commercial Devices) ................................58
Cross Reference of Device Specs for
Table 10-2:
Oscillator Configurations (HS, LP & JW)
and Frequencies of Operation
(Commercial Devices) ................................58
External Clock Timing Requirements -
PIC16C54/55/56/57 ....................................65
CLKOUT and I/O Timing Requirements -
PIC16C54/55/56/57 ....................................67
Reset, Watchdog Timer, and Device Reset
Timer - PIC16C54/55/56/57........................68
Timer0 Clock Requirements -
Table 10-3:
Table 10-4:
Table 10-5:
Table 10-6:
PIC16C54/55/56/57 ....................................69
RC Oscillator Frequencies..........................71
Input Capacitance for PIC16C54/56...........78
Input Capacitance for PIC16C55/57...........78
Cross Reference of Device Specs for
Table 11-1:
Table 11-2:
Table 11-3:
Table 12-1:
Oscillator Configurations and Frequencies
of Operation (Commercial Devices)............80
External Clock Timing Requirements -
PIC16CR54.................................................86
CLKOUT and I/O Timing Requirements -
PIC16CR54.................................................88
Reset, Watchdog Timer, and Device Reset
Timer - PIC16CR54 ....................................89
Timer0 Clock Requirements - PIC16CR54.90
RC Oscillator Frequencies..........................91
Input Capacitance for PIC16CR54 .............99
PIC16C5X Family of Devices ...................117
PIC16C62X Family of Devices .................118
PIC16C6X Family of Devices ...................119
PIC16C7X Family of Devices ...................120
PIC16C8X Family of Devices ...................121
PIC17CXX Family of Devices...................122
Pin Compatible Devices............................123
Table 12-2:
Table 12-3:
Table 12-4:
Table 12-5:
Table 13-1:
Table 13-2:
Table D-1:
Table D-2:
Table D-3:
Table D-4:
Table D-5:
Table D-6:
Table D-7:
DS30236B-page 198
1996 Microchip Technology Inc.
Enhanced PIC16C5X
CONNECTING TO MICROCHIP BBS
Trademarks:
Connect worldwide to the Microchip BBS using the
CompuServe communications network. In most
cases a local call is your only expense. The Microchip
BBS connection does not use CompuServe
membership services, therefore, you do not need
CompuServe membership to join Microchip's BBS.
PICMASTER, PICSTART, the Microchip logo and
name are registered trademarks of Microchip
Technology Inc. PIC is a registered trademark of
Microchip Technology Incorporated in the U.S.A.
PRO MATE, fuzzyLAB are trademarks of
Microchip Technology Incorporated.
There is no charge for connecting to the BBS, except
toll charge to CompuServe access number, where
applicable. You do not need to be a CompuServe
member to take advantage of this connection (you
never actually log in to CompuServe).
SQTP is a service mark of Microchip
Technology Inc.
fuzzyTECH is a registered trademark of Inform
Software Corporation.
2
The procedure to connect will vary slightly from
country to country. Please check with your local
CompuServe agent for details if you have a problem.
CompuServe service allows multiple users at baud
rates up to 14,400 bps.
I C is a trademark of Philips Corporation.
IBM, IBM PC-AT are registered trademarks of
International Business Machines Corp.
Pentium is a trademark of Intel Corporation.
The following connect procedure applies in most
locations:
MS-DOS, Microsoft Windows and Windows are
registered trademarks of Microsoft Corporation.
1. Set your modem to 8-bit, No parity, and One
stop (8N1). This is not the normal CompuServe
setting which is 7E1.
CompuServe is a registered trademark of
CompuServe Incorporated.
All other trademarks mentioned herein are the
property of their respective companies.
2. Dial your local CompuServe access number.
3. Depress <ENTER > and a garbage string will
appear because CompuServe is expecting a
7E1 setting.
4. Type +, depress <ENTER > and Host Name:
will appear.
5. Type MCHIPBBS, depress < ENTER > and
you will be connected to the Microchip BBS.
In the United States, to find CompuServe's phone
number closest to you, set your modem to 7E1 and
dial (800) 848-4480 for 300-2400 baud or
(800) 331-7166 for 9600-14400 baud connection. After
the system responds with Host Name:
Type, NETWORK, depress < ENTER > and follow
CompuServe's directions.
For voice information (or calling from overseas), you
may call (614) 723-1550 for your local CompuServe
number.
ACCESS TO THE INTERNET
Microchip’s current WWW address is listed on the
back page of this data sheet under Worldwide Sales &
Service - Americas - Corporate Office.
1996 Microchip Technology Inc.
DS30236B-page 199
Enhanced PIC16C5X
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product.
If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can
better serve you, please FAX your comments to the Technical Publications Manager at (602) 786-7578.
Please list the following information, and use this outline to provide us with your comments about this Data Sheet.
To:
Technical Publications Manager
Reader Response
Total Pages Sent
RE:
From:
Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
Device:
Literature Number:
Enhanced PIC16C5X
Questions:
1. What are the best features of this document?
DS30236B
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this data sheet easy to follow? If not, why?
4. What additions to the data sheet do you think would enhance the structure and subject?
5. What deletions from the data sheet could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
8. How would you improve our software, systems, and silicon products?
DS30236B-page 200
1996 Microchip Technology Inc.
Enhanced PIC16C5X
ENHANCED PIC16C5X PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
X
/XX
XXX
PART NO.
Device
-XX
Examples:
Frequency Temperature Package
Range Range
Pattern
a) PIC16C54A -04/P 301 = Commercial
temp., PDIPpackage, 4MHz, normal VDD
limitis, QTP pattern #301.
(2)
(3)
Device
PIC16C5X , PIC16C5XT
PIC16LC5X , PIC16LC5XT
b) PIC16LC58A - 04I/SO = Industrial temp.,
SOIC package, 4MHz, Extended VDD
limits.
(2)
(3)
(2)
(3)
PIC16CR5X , PIC16CR5XT
(2)
(3)
PIC16LCR5X , PIC16LCR5XT
c) PIC16CR57A - 10E/P355 = ROM pro-
gram memory, Automotive temp., PDIP
package, 10MHz, normal VDD limits.
Frequency
Range
04
10
20
= 4 MHz
= 10 MHz
= 20 MHz
(1)
(4)
b
= No type for JW devices
Note 1: b = blank
(1)
Temperature
Range
b
I
= 0°C to +70°C (Commercial)
= -40°C to +85°C (Industrial)
= -40°C to +125°C (Automotive)
2:
C
= Standard VDD range
LC = Extended VDD range
CR = ROM Version, Standard VDD
range
LCR = ROM Version, Extended VDD
range
E
Package
JW
P
SO
SP
SS
= Windowed CERDIP
= PDIP
= SOIC (Gull Wing, 300 mil body)
= Skinny PDIP (28 pin, 300 mil body)
= SSOP (209 mil body)
3: T = in tape and reel - SOIC, SSOP
packages only.
4: UV erasable devices are tested to all
available voltage/frequency options.
Erased devices are oscillator type
04. The user can select 04, 10 or 20
oscillators by programmng the appro-
priate configuration bits.
Pattern
3-digit Pattern Code for QTP, ROM (blank otherwise)
Sales and Support
Products supported by a preliminary Data Sheet may possibly have an errata sheet describing minor operational differences and
recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
1. Your local Microchip sales office (see below)
2. The Microchip Corporate Literature Center U.S. FAX: (602) 786-7277
3. The Microchip’s Bulletin Board, via your local CompuServe number (CompuServe membership NOT required).
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using.
For latest version information and upgrade kits for Microchip Development Tools, please call 1-800-755-2345 or 1-602-786-7302.
1996 Microchip Technology Inc.
DS30236B-page 201
WORLDWIDE SALES & SERVICE
AMERICAS
ASIA/PACIFIC
EUROPE
Corporate Office
Hong Kong
United Kingdom
Microchip Technology Inc.
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 602 786-7200 Fax: 602 786-7277
Technical Support: 602 786-7627
Web: http://www.mchip.com/microchip
Microchip Technology
Unit No. 3002-3004, Tower 1
Metroplaza
223 Hing Fong Road
Kwai Fong, N.T. Hong Kong
Tel: 852 2 401 1200 Fax: 852 2 401 3431
Arizona Microchip Technology Ltd.
Unit 6, The Courtyard
Meadow Bank, Furlong Road
Bourne End, Buckinghamshire SL8 5AJ
Tel: 44 1628 851077 Fax: 44 1628 850259
France
Korea
Arizona Microchip Technology SARL
2 Rue du Buisson aux Fraises
91300 Massy - France
Tel: 33 1 69 53 63 20 Fax: 33 1 69 30 90 79
Germany
Arizona Microchip Technology GmbH
Gustav-Heinemann-Ring 125
D-81739 Muenchen, Germany
Tel: 49 89 627 144 0 Fax: 49 89 627 144 44
Atlanta
Microchip Technology
168-1, Youngbo Bldg. 3 Floor
Samsung-Dong, Kangnam-Ku,
Seoul, Korea
Tel: 82 2 554 7200 Fax: 82 2 558 5934
Singapore
Microchip Technology
200 Middle Road
#10-03 Prime Centre
Singapore 188980
Tel: 65 334 8870 Fax: 65 334 8850
Taiwan
Microchip Technology
10F-1C 207
Tung Hua North Road
Taipei, Taiwan, ROC
Tel: 886 2 717 7175 Fax: 886 2 545 0139
Microchip Technology Inc.
500 Sugar Mill Road, Suite 200B
Atlanta, GA 30350
Tel: 770 640-0034 Fax: 770 640-0307
Boston
Microchip Technology Inc.
5 Mount Royal Avenue
Marlborough, MA 01752
Tel: 508 480-9990
Chicago
Microchip Technology Inc.
333 Pierce Road, Suite 180
Itasca, IL 60143
Tel: 708 285-0071 Fax: 708 285-0075
Dallas
Microchip Technology Inc.
14651 Dallas Parkway, Suite 816
Dallas, TX 75240-8809
Tel: 214 991-7177 Fax: 214 991-8588
Dayton
Microchip Technology Inc.
Suite 150
Italy
Fax: 508 480-8575
Arizona Microchip Technology SRL
Centro Direzionale Colleoni
Palazzo Pegaso Ingresso No. 2
Via Paracelso 23, 20041
Agrate Brianza (MI) Italy
Tel: 39 39 689 9939 Fax: 39 39 689 9883
JAPAN
Microchip Technology Intl. Inc.
Benex S-1 6F
3-18-20, Shin Yokohama
Kohoku-Ku, Yokohama
Kanagawa 222 Japan
Tel: 81 45 471 6166 Fax: 81 45 471 6122
Two Prestige Place
Miamisburg, OH 45342
Tel: 513 291-1654 Fax: 513 291-9175
01/04/96
Los Angeles
Microchip Technology Inc.
18201 Von Karman, Suite 1090
Irvine, CA 92715
Tel: 714 263-1888 Fax: 714 263-1338
NewYork
Microchip Technology Inc.
150 Motor Parkway, Suite 416
Hauppauge, NY 11788
Tel: 516 273-5305 Fax: 516 273-5335
San Jose
Microchip Technology Inc.
2107 North First Street, Suite 590
San Jose, CA 95131
Tel: 408 436-7950 Fax: 408 436-7955
All rights reserved. 1996, Microchip Technology Incorporated, USA.
Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. No representation or warranty
is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property
rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip.
No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. All rights
reserved. All other trademarks mentioned herein are the property of their respective companies.
DS30236B-page 202
1996 Microchip Technology Inc.
相关型号:
PIC16CR54B-20/P301
8-BIT, MROM, 20 MHz, RISC MICROCONTROLLER, PDIP18, 0.300 INCH, PLASTIC, DIP-18
MICROCHIP
PIC16CR54B-20E/SS
8-BIT, MROM, 20 MHz, RISC MICROCONTROLLER, PDSO20, 5.30 MM, PLASTIC, SSOP-20
MICROCHIP
PIC16CR54B-20I/P301
8-BIT, MROM, 20 MHz, RISC MICROCONTROLLER, PDIP18, 0.300 INCH, PLASTIC, DIP-18
MICROCHIP
PIC16CR54BT-04/SO
8-BIT, MROM, 4 MHz, RISC MICROCONTROLLER, PDSO18, 0.300 INCH, PLASTIC, SO-18
MICROCHIP
PIC16CR54BT-04/SS
8-BIT, MROM, 4 MHz, RISC MICROCONTROLLER, PDSO20, 5.30 MM, PLASTIC, SSOP-20
MICROCHIP
PIC16CR54BT-04E/SO
8-BIT, MROM, 4 MHz, RISC MICROCONTROLLER, PDSO18, 0.300 INCH, PLASTIC, SO-18
MICROCHIP
©2020 ICPDF网 联系我们和版权申明