PIC16HV616T-I/PSQTP [MICROCHIP]
14-Pin, Flash-Based 8-Bit CMOS Microcontrollers; 14引脚,基于闪存的8位CMOS微控制器型号: | PIC16HV616T-I/PSQTP |
厂家: | MICROCHIP |
描述: | 14-Pin, Flash-Based 8-Bit CMOS Microcontrollers |
文件: | 总180页 (文件大小:2877K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PIC16F610/16HV610
PIC16F616/16HV616
Data Sheet
14-Pin, Flash-Based 8-Bit
CMOS Microcontrollers
© 2007 Microchip Technology Inc.
Preliminary
DS41288C
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, microID, MPLAB, PIC,
PICmicro, PICSTART, PRO MATE, PowerSmart, rfPIC, and
SmartShunt are registered trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
AmpLab, FilterLab, Linear Active Thermistor, Migratable
Memory, MXDEV, MXLAB, PS logo, SEEVAL, SmartSensor
and The Embedded Control Solutions Company are
registered trademarks of Microchip Technology Incorporated
in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, ECAN,
ECONOMONITOR, FanSense, FlexROM, fuzzyLAB,
In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi,
MPASM, MPLAB Certified logo, MPLIB, MPLINK, PICkit,
PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal,
PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB,
rfPICDEM, Select Mode, Smart Serial, SmartTel, Total
Endurance, UNI/O, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2007, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona, Gresham, Oregon and Mountain View, California. The
Company’s quality system processes and procedures are for its PIC®
MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial
EEPROMs, microperipherals, nonvolatile memory and analog
products. In addition, Microchip’s quality system for the design and
manufacture of development systems is ISO 9001:2000 certified.
DS41288C-page ii
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
14-Pin Flash-Based, 8-Bit CMOS Microcontrollers
High-Performance RISC CPU:
Peripheral Features:
• Only 35 instructions to learn:
- All single-cycle instructions except branches
• Operating speed:
• Shunt Voltage Regulator (PIC16HV610/616 only):
- 5 volt regulation
- 4 mA to 50 mA shunt range
• 11 I/O pins and 1 input only
- DC – 20 MHz oscillator/clock input
- DC – 200 ns instruction cycle
- High current source/sink for direct LED drive
- Interrupt-on-Change pins
- Individually programmable weak pull-ups
• Interrupt capability
• 8-level deep hardware stack
• Direct, Indirect and Relative Addressing modes
• Analog Comparator module with:
- Two analog comparators
- Programmable on-chip voltage reference
(CVREF) module (% of VDD)
- Fixed Voltage Reference
- Comparator inputs and outputs externally
accessible
Special Microcontroller Features:
• Precision Internal Oscillator:
- Factory calibrated to ±1%, typical
- User selectable frequency: 4 MHz or 8 MHz
- SR Latch
- Built-In Hysteresis (user selectable)
• Power-Saving Sleep mode
• Voltage range:
• Timer0: 8-bit timer/counter with 8-bit
programmable prescaler
- PIC16F610/616: 2.0V to 5.5V
- PIC16HV610/616: 2.0V to user defined
maximum (see note)
• Enhanced Timer1:
- 16-bit timer/counter with prescaler
- External Timer1 Gate (count enable)
- Option to use OSC1 and OSC2 in LP mode
as Timer1 oscillator if INTOSC mode
selected
• Industrial and Extended Temperature range
• Power-on Reset (POR)
• Power-up Timer (PWRT) and Oscillator Start-up
Timer (OST)
- Timer1 oscillator
• Brown-out Reset (BOR)
• In-Circuit Serial ProgrammingTM (ICSPTM) via two
pins
• Watchdog Timer (WDT) with independent
oscillator for reliable operation
• Multiplexed Master Clear with pull-up/input pin
• Programmable code protection
• High Endurance Flash:
PIC16F616/16HV616 only:
• A/D Converter:
- 10-bit resolution
- 8 external input channels
- 2 internal reference channels
- 100,000 write Flash endurance
- Flash retention: > 40 years
• Timer2: 8-bit timer/counter with 8-bit period
register, prescaler and postscaler
Low-Power Features:
• Standby Current:
• Enhanced Capture, Compare, PWM module:
- 50 nA @ 2.0V, typical
• Operating Current:
- 16-bit Capture, max. resolution 12.5 ns
- 16-bit Compare, max. resolution 200 ns
- 10-bit PWM with 1, 2 or 4 output channels,
programmable “dead time”, max. frequency
20 kHz
- 20 μA @ 32 kHz, 2.0V, typical
- 220 μA @ 4 MHz, 2.0V, typical
• Watchdog Timer Current:
- 1 μA @ 2.0V, typical
Note:
Voltage across internal shunt regulator
cannot exceed 5V.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 1
PIC16F610/616/16HV610/616
Program Memory
Data Memory
SRAM (bytes)
10-bit A/D
(ch)
Timers
8/16-bit
Device
I/O
Comparators
Voltage Range
Flash
(words)
PIC16F610
PIC16HV610
PIC16F616
PIC16HV616
1024
1024
2048
2048
64
64
11
11
11
11
—
—
8
2
2
2
2
1/1
1/1
2/1
2/1
2.0-5.5V
2.0-user defined
2.0-5.5V
128
128
8
2.0-user defined
PIC16F610/16HV610 14-Pin Diagram (PDIP, SOIC, TSSOP)
VDD
VSS
1
2
3
4
5
6
7
14
13
12
11
10
9
RA5/T1CKI/OSC1/CLKIN
RA4/T1G/OSC2/CLKOUT
RA3/MCLR/VPP
RC5
RA0/C1IN+/ICSPDAT
RA1/C12IN0-/ICSPCLK
RA2/T0CKI/INT/C1OUT
RC0/C2IN+
RC4/C2OUT
RC1/C12IN1-
RC3/C12IN3-
8
RC2/C12IN2-
TABLE 1:
I/O
PIC16F610/16HV610 14-PIN SUMMARY
Pin
Comparators
Timer
Interrupts
Pull-ups
Basic
RA0
13
12
11
C1IN+
C12IN0-
C1OUT
—
—
IOC
IOC
Y
Y
Y
ICSPDAT
ICSPCLK
—
RA1
RA2
T0CKI
INT/IOC
RA3(1)
4
3
—
—
—
T1G
T1CKI
—
IOC
IOC
IOC
—
Y(2)
Y
MCLR/VPP
RA4
RA5
RC0
RC1
RC2
RC3
RC4
RC5
—
OSC2/CLKOUT
2
—
Y
OSC1/CLKIN
10
9
C2IN+
C12IN1-
C12IN2-
C12IN3-
C2OUT
—
—
—
—
—
—
—
—
—
—
—
—
—
8
—
—
—
7
—
—
—
6
—
—
—
5
—
—
—
1
—
—
—
VDD
VSS
—
14
—
—
—
Note 1: Input only.
2: Only when pin is configured for external MCLR.
DS41288C-page 2
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
PIC16F616/16HV616 14-Pin Diagram (PDIP, SOIC, TSSOP)
VDD
RA5/T1CKI/OSC1/CLKIN
RA4/AN3/T1G/OSC2/CLKOUT
RA3/MCLR/VPP
VSS
1
2
3
4
5
6
7
14
13
12
11
10
9
RA0/AN0/C1IN+/ICSPDAT
RA1/AN1/C12IN0-/VREF/ICSPCLK
RA2/AN2/T0CKI/INT/C1OUT
RC0/AN4/C2IN+
RC5/CCP1/P1A
RC4/C2OUT/P1B
RC1/AN5/C12IN1-
RC3/AN7/C12IN3-/P1C
8
RC2/AN6/C12IN2-/P1D
TABLE 2:
PIC16F616/16HV616 14-PIN SUMMARY
I/O
Pin
Analog
Comparators
Timer
CCP
Interrupts Pull-ups
Basic
RA0
13
12
11
AN0
AN1/VREF
AN2
C1IN+
C12IN0-
C1OUT
—
—
—
—
—
IOC
IOC
Y
Y
Y
ICSPDAT
ICSPCLK
—
RA1
RA2
T0CKI
INT/IOC
RA3(1)
4
3
—
AN3
—
—
—
—
T1G
T1CKI
—
—
—
IOC
IOC
IOC
—
Y(2)
Y
MCLR/VPP
RA4
RA5
RC0
RC1
RC2
RC3
RC4
RC5
—
OSC2/CLKOUT
2
—
—
Y
OSC1/CLKIN
10
9
AN4
AN5
AN6
AN7
—
C2IN+
C12IN1-
C12IN2-
C12IN3-
C2OUT
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
8
—
P1D
P1C
P1B
CCP1/P1A
—
—
—
7
—
—
—
6
—
—
—
5
—
—
—
—
1
—
—
—
—
VDD
VSS
—
14
—
—
—
—
—
Note 1: Input only.
2: Only when pin is configured for external MCLR.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 3
PIC16F610/616/16HV610/616
PIC16F610/16HV610 16-Pin Diagram (QFN)
RA5/T1CKI/OSC1/CLKIN
RA4/T1G/OSC2/CLKOUT
RA3/MCLR/VPP
RA0/C1IN+/ICSPDAT
RA1/C12IN0-/ICSPCLK
RA2/T0CKI/INT/C1OUT
RC0/C2IN1+
12
11
10
9
1
2
3
4
PIC16F610/
PIC16HV610
RC5
TABLE 3:
I/O
PIC16F610/16HV610 16-PIN SUMMARY
Pin
Comparators
Timers
Interrupts
Pull-ups
Basic
RA0
12
11
10
C1IN+
C12IN0-
C1OUT
—
—
IOC
IOC
Y
Y
Y
ICSPDAT
ICSPCLK
—
RA1
RA2
T0CKI
INT/IOC
RA3(1)
3
2
—
—
—
T1G
T1CKI
—
IOC
IOC
IOC
—
Y(2)
Y
MCLR/VPP
RA4
RA5
RC0
RC1
RC2
RC3
RC4
RC5
—
OSC2/CLKOUT
1
—
Y
OSC1/CLKIN
9
C2IN+
C12IN1-
C12IN2-
C12IN3-
C2OUT
—
—
—
—
—
—
—
—
—
—
—
8
—
—
7
—
—
—
6
—
—
—
5
—
—
—
4
—
—
—
16
13
—
—
—
VDD
VSS
—
—
—
—
Note 1: Input only.
2: Only when pin is configured for external MCLR.
DS41288C-page 4
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
PIC16F616/16HV616 16-Pin Diagram (QFN)
RA5/T1CKI/OSC1/CLKIN
RA4/AN3/T1G/OSC2/CLKOUT
RA3/MCLR/VPP
RA0/AN0/C1IN+/ICSPDAT
RA1/AN1/C12IN0-/VREF/ICSPCLK
RA2/AN2/T0CKI/INT/C1OUT
RC0/AN4/C2IN1+
12
11
10
9
1
2
3
4
PIC16F616/
PIC16HV616
RC5/CCP/P1A
TABLE 4:
PIC16F616/16HV616 16-PIN SUMMARY
I/O
Pin
Analog
Comparators
Timers
CCP
Interrupts Pull-ups
Basic
RA0
12
11
10
AN0
AN1/VREF
AN2
C1IN+
C12IN0-
C1OUT
—
—
—
—
—
IOC
IOC
Y
Y
Y
ICSPDAT
ICSPCLK
—
RA1
RA2
T0CKI
INT/IOC
RA3(1)
3
2
—
AN3
—
—
—
—
T1G
T1CKI
—
—
—
IOC
IOC
IOC
—
Y(2)
Y
MCLR/VPP
RA4
RA5
RC0
RC1
RC2
RC3
RC4
RC5
—
OSC2/CLKOUT
1
—
—
Y
OSC1/CLKIN
9
AN4
AN5
AN6
AN7
—
C2IN+
C12IN1-
C12IN2-
C12IN3-
C2OUT
—
—
—
—
—
—
—
—
—
—
—
—
8
—
—
—
7
—
P1D
P1C
P1B
CCP1/P1A
—
—
—
6
—
—
—
5
—
—
—
4
—
—
—
—
16
13
—
—
—
—
VDD
VSS
—
—
—
—
—
—
Note 1: Input only.
2: Only when pin is configured for external MCLR.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 5
PIC16F610/616/16HV610/616
Table of Contents
1.0 Device Overview .......................................................................................................................................................................... 7
2.0 Memory Organization................................................................................................................................................................. 11
3.0 Oscillator Module........................................................................................................................................................................ 25
4.0 I/O Ports ..................................................................................................................................................................................... 31
5.0 Timer0 Module ........................................................................................................................................................................... 43
6.0 Timer1 Module with Gate Control............................................................................................................................................... 47
7.0 Timer2 Module ........................................................................................................................................................................... 53
8.0 Comparator Module.................................................................................................................................................................... 55
9.0 Analog-to-Digital Converter (ADC) Module ................................................................................................................................ 71
10.0 Enhanced Capture/Compare/PWM (With Auto-Shutdown and Dead Band) Module................................................................. 83
11.0 Voltage Regulator..................................................................................................................................................................... 105
12.0 Special Features of the CPU.................................................................................................................................................... 106
13.0 Instruction Set Summary.......................................................................................................................................................... 125
14.0 Development Support............................................................................................................................................................... 135
15.0 Electrical Specifications............................................................................................................................................................ 139
16.0 DC and AC Characteristics Graphs and Tables....................................................................................................................... 161
17.0 Packaging Information.............................................................................................................................................................. 163
Appendix A: Data Sheet Revision History.......................................................................................................................................... 169
®
Appendix B: Migrating from other PIC Devices................................................................................................................................ 169
Index .................................................................................................................................................................................................. 171
The Microchip Web Site..................................................................................................................................................................... 175
Customer Change Notification Service .............................................................................................................................................. 175
Customer Support.............................................................................................................................................................................. 175
Reader Response .............................................................................................................................................................................. 176
Product Identification System............................................................................................................................................................. 177
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We
welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of
silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are
using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
DS41288C-page 6
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
1.0
DEVICE OVERVIEW
The PIC16F610/616/16HV610/616 is covered by this
data sheet. It is available in 14-pin PDIP, SOIC, TSSOP
and 16-pin QFN packages.
Block Diagrams and pinout descriptions of the devices
are as follows:
• PIC16F610/16HV610 (Figure 1-1, Table 1-1)
• PIC16F616/16HV616 (Figure 1-2, Table 1-2)
FIGURE 1-1:
PIC16F610/16HV610 BLOCK DIAGRAM
INT
Configuration
13
8
PORTA
Data Bus
Program Counter
RA0
RA1
RA2
RA3
RA4
RA5
Flash
1K X 14
Program
Memory
RAM
64 Bytes
File
Registers
8-Level Stack
(13-Bit)
Program
Bus
14
RAM Addr
9
Addr MUX
Instruction Reg
PORTC
Indirect
Addr
7
Direct Addr
8
RC0
RC1
RC2
RC3
RC4
RC5
FSR Reg
STATUS Reg
8
3
MUX
Power-up
Timer
Oscillator
Instruction
Decode and
Control
Start-up Timer
ALU
Power-on
Reset
8
Watchdog
Timer
Timing
Generation
OSC1/CLKIN
W Reg
Brown-out
Reset
OSC2/CLKOUT
Internal
Oscillator
Block
Shunt Regulator
(PIC16HV610 only)
VDD
VSS
MCLR
T1G
T1CKI
Timer0
Timer1
T0CKI
Comparator Voltage Reference
Fixed Voltage Reference
2 Analog Comparators
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 7
PIC16F610/616/16HV610/616
FIGURE 1-2:
PIC16F616/16HV616 BLOCK DIAGRAM
INT
Configuration
13
8
PORTA
Data Bus
Program Counter
RA0
RA1
RA2
RA3
RA4
RA5
Flash
2K X 14
Program
Memory
RAM
128 Bytes
File
Registers
8-Level Stack
(13-Bit)
Program
Bus
14
RAM Addr
9
Addr MUX
Instruction Reg
PORTC
Indirect
Addr
7
Direct Addr
8
RC0
RC1
RC2
RC3
RC4
RC5
FSR Reg
STATUS Reg
8
3
MUX
Power-up
Timer
Oscillator
Instruction
Decode and
Control
Start-up Timer
ALU
Power-on
Reset
8
Watchdog
Timer
Timing
Generation
OSC1/CLKIN
W Reg
Brown-out
Reset
OSC2/CLKOUT
Internal
Oscillator
Block
Shunt Regulator
(PIC16HV616 only)
VDD
VSS
MCLR
T1G
T1CKI
Timer0
Timer1
Timer2
T0CKI
Comparator Voltage Reference
Fixed Voltage Reference
2 Analog Comparators
Analog-To-Digital Converter
ECCP
DS41288C-page 8
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 1-1:
PIC16F610/16HV610 PINOUT DESCRIPTION
Input
Type
Output
Type
Name
Function
Description
RA0/C1IN+/ICSPDAT
RA1/C12IN0-/ICSPCLK
RA2/T0CKI/INT/C1OUT
RA0
C1IN+
ICSPDAT
RA1
TTL
AN
ST
TTL
AN
ST
ST
ST
ST
—
CMOS
—
PORTA I/O with prog. pull-up and interrupt-on-change
Comparator C1 non-inverting input
Serial Programming Data I/O
CMOS
CMOS
—
PORTA I/O with prog. pull-up and interrupt-on-change
Comparators C1 and C2 inverting input
Serial Programming Clock
C12IN0-
ICSPCLK
RA2
—
CMOS
—
PORTA I/O with prog. pull-up and interrupt-on-change
Timer0 clock input
T0CKI
INT
—
External Interrupt
C1OUT
CMOS
Comparator C1 output
RA3/MCLR/VPP
RA3
TTL
—
PORTA input with interrupt-on-change
MCLR
VPP
ST
HV
—
—
Master Clear w/internal pull-up
Programming voltage
RA4/T1G/OSC2/CLKOUT
RA4
TTL
CMOS
PORTA I/O with prog. pull-up and interrupt-on-change
T1G
OSC2
CLKOUT
RA5
ST
—
—
XTAL
CMOS
CMOS
—
Timer1 gate (count enable)
Crystal/Resonator
—
FOSC/4 output
RA5/T1CKI/OSC1/CLKIN
TTL
ST
PORTA I/O with prog. pull-up and interrupt-on-change
Timer1 clock input
T1CKI
OSC1
CLKIN
RC0
XTAL
ST
—
Crystal/Resonator
—
External clock input/RC oscillator connection
PORTC I/O
RC0/C2IN+
TTL
AN
CMOS
—
C2IN+
RC1
Comparator C2 non-inverting input
PORTC I/O
RC1/C12IN1-
RC2/C12IN2-
RC3/C12IN3-
RC4/C2OUT
TTL
AN
CMOS
—
C12IN1-
RC2
Comparators C1 and C2 inverting input
PORTC I/O
TTL
AN
CMOS
—
C12IN2-
RC3
Comparators C1 and C2 inverting input
PORTC I/O
TTL
AN
CMOS
—
C12IN3-
RC4
Comparators C1 and C2 inverting input
PORTC I/O
TTL
—
CMOS
CMOS
CMOS
—
C2OUT
RC5
Comparator C2 output
PORTC I/O
RC5
VDD
VSS
TTL
Power
Power
VDD
Positive supply
VSS
—
Ground reference
Legend:
AN = Analog input or output
CMOS = CMOS compatible input or output HV
=
High Voltage
ST = Schmitt Trigger input with CMOS levels TTL
= TTL compatible input
XTAL = Crystal
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 9
PIC16F610/616/16HV610/616
TABLE 1-2:
PIC16F616/16HV616 PINOUT DESCRIPTION
Input
Type
Output
Type
Name
Function
Description
RA0/AN0/C1IN+/ICSPDAT
RA0
AN0
TTL
AN
AN
ST
TTL
AN
AN
AN
ST
ST
AN
ST
ST
—
CMOS
—
PORTA I/O with prog. pull-up and interrupt-on-change
A/D Channel 0 input
C1IN+
ICSPDAT
RA1
—
Comparator C1 non-inverting input
Serial Programming Data I/O
PORTA I/O with prog. pull-up and interrupt-on-change
A/D Channel 1 input
CMOS
CMOS
—
RA1/AN1/C12IN0-/VREF/ICSPCLK
AN1
C12IN0-
VREF
—
Comparators C1 and C2 inverting input
External Voltage Reference for A/D
Serial Programming Clock
—
ICSPCLK
RA2
—
RA2/AN2/T0CKI/INT/C1OUT
CMOS
—
PORTA I/O with prog. pull-up and interrupt-on-change
A/D Channel 2 input
AN2
T0CKI
INT
—
Timer0 clock input
—
External Interrupt
C1OUT
CMOS
Comparator C1 output
RA3/MCLR/VPP
RA3
MCLR
VPP
TTL
ST
—
—
PORTA input with interrupt-on-change
Master Clear w/internal pull-up
Programming voltage
HV
TTL
AN
—
RA4/AN3/T1G/OSC2/CLKOUT
RA4
CMOS
—
PORTA I/O with prog. pull-up and interrupt-on-change
A/D Channel 3 input
AN3
T1G
OSC2
CLKOUT
RA5
ST
—
—
XTAL
CMOS
CMOS
—
Timer1 gate (count enable)
Crystal/Resonator
—
FOSC/4 output
RA5/T1CKI/OSC1/CLKIN
TTL
ST
PORTA I/O with prog. pull-up and interrupt-on-change
Timer1 clock input
T1CKI
OSC1
CLKIN
RC0
XTAL
ST
—
Crystal/Resonator
—
External clock input/RC oscillator connection
PORTC I/O
RC0/AN4/C2IN+
TTL
AN
CMOS
—
AN4
A/D Channel 4 input
Comparator C2 non-inverting input
PORTC I/O
C2IN+
RC1
AN
—
RC1/AN5/C12IN1-
RC2/AN6/C12IN2-/P1D
TTL
AN
CMOS
—
AN5
A/D Channel 5 input
Comparators C1 and C2 inverting input
PORTC I/O
C12IN1-
RC2
AN
—
TTL
AN
CMOS
—
AN6
A/D Channel 6 input
Comparators C1 and C2 inverting input
PWM output
C12IN2-
P1D
AN
—
—
CMOS
CMOS
—
RC3/AN7/C12IN3-/P1C
RC3
TTL
AN
PORTC I/O
AN7
A/D Channel 7 input
Comparators C1 and C2 inverting input
PWM output
C12IN3-
P1C
AN
—
—
CMOS
CMOS
CMOS
CMOS
CMOS
CMOS
CMOS
—
RC4/C2OUT/P1B
RC5/CCP1/P1A
RC4
TTL
—
PORTC I/O
C2OUT
P1B
Comparator C2 output
PWM output
—
RC5
TTL
ST
PORTC I/O
CCP1
P1A
Capture input/Compare output
PWM output
—
VDD
VSS
VDD
Power
Power
Positive supply
VSS
—
Ground reference
Legend:
AN = Analog input or output
CMOS = CMOS compatible input or output HV
= High Voltage
ST = Schmitt Trigger input with CMOS levels TTL
= TTL compatible input
XTAL = Crystal
DS41288C-page 10
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
FIGURE 2-2:
PROGRAM MEMORY MAP
AND STACK FOR THE
PIC16F616/16HV616
2.0
2.1
MEMORY ORGANIZATION
Program Memory Organization
PC<12:0>
13
The PIC16F610/616/16HV610/616 has a 13-bit pro-
gram counter capable of addressing an 8k x 14 pro-
CALL, RETURN
RETFIE, RETLW
gram memory space. Only the first 1K
x 14
(0000h-3FF) for the PIC16F610/16HV610 and the first
2K x 14 (0000h-07FFh) for the PIC16F616/16HV616 is
physically implemented. Accessing a location above
these boundaries will cause a wraparound within the
first 1K x 14 space (PIC16F610/16HV610) and 2K x 14
space (PIC16F616/16HV616). The Reset vector is at
0000h and the interrupt vector is at 0004h (see
Figure 2-1).
Stack Level 1
Stack Level 2
Stack Level 8
Reset Vector
0000h
FIGURE 2-1:
PROGRAM MEMORY MAP
AND STACK FOR THE
PIC16F610/16HV610
Interrupt Vector
0004h
0005h
PC<12:0>
13
On-chip Program
Memory
CALL, RETURN
RETFIE, RETLW
07FFh
0800h
Stack Level 1
Stack Level 2
1FFFh
Stack Level 8
Reset Vector
0000h
Interrupt Vector
0004h
0005h
On-chip Program
Memory
03FFh
0400h
1FFFh
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 11
PIC16F610/616/16HV610/616
2.2.1
GENERAL PURPOSE REGISTER
FILE
2.2
Data Memory Organization
The data memory (see Figure 2-4) is partitioned into
two banks, which contain the General Purpose
Registers (GPR) and the Special Function Registers
(SFR). The Special Function Registers are located in
The register file is organized as 64 x 8 in the
PIC16F610/16HV610 and 128 x 8 in the
PIC16F616/16HV616. Each register is accessed,
either directly or indirectly, through the File Select Reg-
ister (FSR) (see Section 2.4 “Indirect Addressing,
INDF and FSR Registers”).
the
first
32
locations
of
each
bank.
PIC16F610/16HV610 Register locations 40h-7Fh in
Bank 0 are General Purpose Registers, implemented
as static RAM. PIC16F616/16HV616 Register
locations 20h-7Fh in Bank 0 and A0h-BFh in Bank 1
are General Purpose Registers, implemented as static
RAM. Register locations F0h-FFh in Bank 1 point to
addresses 70h-7Fh in Bank 0. All other RAM is
unimplemented and returns ‘0’ when read. The RP0 bit
of the STATUS register is the bank select bit.
2.2.2
SPECIAL FUNCTION REGISTERS
The Special Function Registers are registers used by
the CPU and peripheral functions for controlling the
desired operation of the device (see Table 2-1). These
registers are static RAM.
The special registers can be classified into two sets:
core and peripheral. The Special Function Registers
associated with the “core” are described in this section.
Those related to the operation of the peripheral features
are described in the section of that peripheral feature.
RP0
0
1
→
→
Bank 0 is selected
Bank 1 is selected
Note:
The IRP and RP1 bits of the STATUS
register are reserved and should always be
maintained as ‘0’s.
DS41288C-page 12
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
FIGURE 2-3:
DATA MEMORY MAP OF
THE PIC16F610/16HV610
FIGURE 2-4:
DATA MEMORY MAP OF
THE PIC16F616/16HV616
File
File
File
File
Address
Address
Address
Address
Indirect Addr.(1)
Indirect Addr.(1)
Indirect Addr.(1)
OPTION_REG
PCL
Indirect Addr.(1)
OPTION_REG
PCL
00h
01h
02h
80h
81h
82h
00h
01h
02h
80h
81h
82h
TMR0
PCL
TMR0
PCL
STATUS
FSR
STATUS
FSR
STATUS
FSR
STATUS
FSR
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
1Fh
20h
83h
84h
85h
86h
87h
88h
89h
8Ah
8Bh
8Ch
8Dh
8Eh
8Fh
90h
91h
92h
93h
94h
95h
96h
97h
98h
99h
9Ah
9Bh
9Ch
9Dh
9Eh
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
1Fh
20h
83h
84h
85h
86h
87h
88h
89h
8Ah
8Bh
8Ch
8Dh
8Eh
8Fh
90h
91h
92h
93h
94h
95h
96h
97h
98h
99h
9Ah
9Bh
9Ch
9Dh
9Eh
PORTA
TRISA
PORTA
TRISA
PORTC
TRISC
PORTC
TRISC
PCLATH
INTCON
PIR1
PCLATH
INTCON
PIE1
PCLATH
INTCON
PIR1
PCLATH
INTCON
PIE1
TMR1L
TMR1H
T1CON
PCON
TMR1L
TMR1H
PCON
OSCTUNE
ANSEL
T1CON
OSCTUNE
ANSEL
PR2
TMR2
T2CON
CCPR1L
CCPR1H
CCP1CON
PWM1CON
ECCPAS
WPUA
IOCA
WPUA
IOCA
SRCON0
SRCON1
SRCON0
SRCON1
VRCON
VRCON
CM1CON0
CM2CON0
CM2CON1
CM1CON0
CM2CON0
CM2CON1
ADRESH
ADCON0
ADRESL
ADCON1
General
9Fh
A0h
9Fh
A0h
Purpose
Registers
32 Bytes
BFh
C0h
General
Purpose
Registers
3Fh
40h
96 Bytes
General
Purpose
Registers
64 Bytes
6Fh
70h
7Fh
F0h
FFh
F0h
FFh
Accesses 70h-7Fh
Bank 1
Accesses 70h-7Fh
Bank 1
7Fh
Bank 0
Bank 0
Unimplemented data memory locations, read as ‘0’.
Note 1: Not a physical register.
Unimplemented data memory locations, read as ‘0’.
Note 1: Not a physical register.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 13
PIC16F610/616/16HV610/616
TABLE 2-1:
PIC16F610/616/16HV610/616 SPECIAL FUNCTION REGISTERS SUMMARY BANK 0
Value on
POR, BOR
Addr
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
Bank 0
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
Timer0 Module’s Register
xxxx xxxx 22, 113
xxxx xxxx 43, 113
0000 0000 22, 113
0001 1xxx 16, 113
xxxx xxxx 22, 113
--x0 x000 31, 113
TMR0
PCL
Program Counter’s (PC) Least Significant Byte
STATUS
FSR
IRP(1)
RP1(1)
RP0
TO
PD
Z
DC
RA1
RC1
C
Indirect Data Memory Address Pointer
PORTA
—
—
—
—
RA5
RC5
RA4
RC4
RA3
RC3
RA2
RC2
RA0
RC0
Unimplemented
—
—
—
PORTC
—
--xx 00xx 40, 113
Unimplemented
Unimplemented
—
—
—
—
—
—
PCLATH
INTCON
PIR1
—
—
Write Buffer for upper 5 bits of Program Counter
---0 0000 22, 113
0000 0000 18, 113
GIE
—
PEIE
ADIF(2)
T0IE
CCP1IF(2)
INTE
C2IF
RAIE
C1IF
T0IF
—
INTF
TMR2IF(2)
RAIF
TMR1IF -000 0-00 20, 113
—
Unimplemented
—
—
TMR1L
TMR1H
T1CON
TMR2(2)
T2CON(2)
CCPR1L(2)
CCPR1H(2)
CCP1CON(2)
PWM1CON(2)
ECCPAS(2)
—
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register
Holding Register for the Most Significant Byte of the 16-bit TMR1 Register
xxxx xxxx 47, 113
xxxx xxxx 47, 113
T1GINV
TMR1GE T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
TMR1CS TMR1ON 0000 0000 50, 113
Timer2 Module Register
0000 0000 53, 113
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
1Fh
—
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 54, 113
Capture/Compare/PWM Register 1 Low Byte
Capture/Compare/PWM Register 1 High Byte
XXXX XXXX 84, 113
XXXX XXXX 84, 113
P1M1
P1M0
PDC6
DC1B1
PDC5
DC1B0
PDC4
CCP1M3
PDC3
CCP1M2
PDC2
CCP1M1
PDC1
CCP1M0 0000 0000 83, 113
PRSEN
PDC0
0000 0000 83, 113
ECCPASE ECCPAS2 ECCPAS1 ECCPAS0 PSSAC1
Unimplemented
PSSAC0
PSSBD1
PSSBD0 0000 0000 100, 113
—
—
VRCON
CM1CON0
CM2CON0
CM2CON1
—
ADRESH(2)
ADCON0(2)
C1VREN
C1ON
C2VREN
C1OUT
C2OUT
VRR
C1OE
C2OE
—
FVREN
C1POL
C2POL
T1ACS
VR3
—
VR2
C1R
VR1
VR0
0000 0000 70, 113
0000 -000 60, 113
0000 -000 61, 113
C1CH1
C2CH1
T1GSS
C1CH0
C2CH0
C2ON
—
C2R
MC1OUT MC2OUT
Unimplemented
C1HYS
C2HYS
C2SYNC 00-0 0010 63, 113
—
—
Most Significant 8 bits of the left shifted A/D result or 2 bits of right shifted result
ADFM VCFG CHS3 CHS2 CHS1 CHS0 GO/DONE
xxxx xxxx 78, 113
0000 0000 76, 113
ADON
Legend:
Note 1:
2:
– = Unimplemented locations read as ‘0’, u= unchanged, x= unknown, q= value depends on condition, shaded = unimplemented
IRP and RP1 bits are reserved, always maintain these bits clear.
PIC16F616/16HV616 only.
DS41288C-page 14
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 2-2:
PIC16F610/616/16HV610/616 SPECIAL FUNCTION REGISTERS SUMMARY BANK 1
Value on
POR, BOR
Addr
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
Bank 1
80h
81h
82h
83h
84h
85h
86h
87h
88h
89h
8Ah
8Bh
8Ch
8Dh
8Eh
8Fh
90h
91h
92h
93h
94h
95h
96h
97h
98h
99h
9Ah
9Bh
9Ch
9Dh
9Eh
9Fh
INDF
Addressing this location uses contents of FSR to address data memory (not a physical register)
xxxx xxxx 22, 113
1111 1111 17, 113
0000 0000 22, 113
0001 1xxx 16, 113
xxxx xxxx 22, 113
--11 1111 31, 113
OPTION_REG
PCL
RAPU
INTEDG
T0CS
T0SE
PSA
PS2
PS1
PS0
Program Counter’s (PC) Least Significant Byte
STATUS
FSR
IRP(1)
RP1(1)
RP0
TO
PD
Z
DC
C
Indirect Data Memory Address Pointer
TRISA
—
—
—
—
TRISA5
TRISC5
TRISA4
TRISC4
TRISA3
TRISC3
TRISA2
TRISC2
TRISA1
TRISC1
TRISA0
TRISC0
Unimplemented
—
—
—
TRISC
—
--11 1111 40, 113
Unimplemented
Unimplemented
—
—
—
—
—
—
PCLATH
INTCON
PIE1
—
—
Write Buffer for upper 5 bits of Program Counter
---0 0000 22, 113
GIE
—
PEIE
ADIE(3)
T0IE
CCP1IE(3)
INTE
C2IE
RAIE
C1IE
T0IF
—
INTF
RAIF
0000 0000 18, 113
TMR2IE(3) TMR1IE -000 0-00 19, 113
—
Unimplemented
—
—
PCON
—
—
—
—
—
—
—
—
POR
BOR
---- --qq 21, 113
Unimplemented
—
—
—
OSCTUNE
ANSEL
PR2(3)
—
—
TUN4
ANS4
TUN3
ANS3(3)
TUN2
ANS2(3)
TUN1
ANS1
TUN0
ANS0
---0 0000 29, 113
1111 1111 32, 114
1111 1111 53, 114
ANS7
ANS6
ANS5
Timer2 Module Period Register
Unimplemented
—
—
—
—
—
Unimplemented
WPUA
IOCA
—
—
—
—
WPUA5
IOCA5
WPUA4
IOCA4
—
WPUA2
IOCA2
WPUA1
IOCA1
WPUA0
IOCA0
--11 -111 33, 114
--00 0000 33, 114
—
IOCA3
Unimplemented
Unimplemented
SR1
—
—
—
—
—
SRCON0
SRCON1
—
SR0
C1SEN
—
C2REN
—
PULSS
—
PULSR
—
—
—
SRCLKEN 0000 00-0 67, 114
SRCS1
SRCS0
—
00-- ---- 67, 114
Unimplemented
Unimplemented
Unimplemented
—
—
—
—
—
—
—
—
ADRESL(3)
ADCON1(3)
Least Significant 2 bits of the left shifted result or 8 bits of the right shifted result
ADCS2 ADCS1 ADCS0 —
xxxx xxxx 78, 114
-000 ---- 77, 114
—
—
—
—
Legend:
Note 1:
2:
– = Unimplemented locations read as ‘0’, u= unchanged, x= unknown, q= value depends on condition, shaded = unimplemented
IRP and RP1 bits are reserved, always maintain these bits clear.
RA3 pull-up is enabled when MCLRE is ‘1’ in the Configuration Word register.
3:
PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 15
PIC16F610/616/16HV610/616
It is recommended, therefore, that only BCF, BSF,
SWAPF and MOVWF instructions are used to alter the
STATUS register, because these instructions do not
affect any Status bits. For other instructions not affect-
ing any Status bits, see the Section 13.0 “Instruction
Set Summary”.
2.2.2.1
STATUS Register
The STATUS register, shown in Register 2-1, contains:
• the arithmetic status of the ALU
• the Reset status
• the bank select bits for data memory (RAM)
The STATUS register can be the destination for any
instruction, like any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to the
device logic. Furthermore, the TO and PD bits are not
writable. Therefore, the result of an instruction with the
STATUS register as destination may be different than
intended.
Note 1: Bits IRP and RP1 of the STATUS register
are
not
used
by
the
PIC16F610/616/16HV610/616
and
should be maintained as clear. Use of
these bits is not recommended, since this
may affect upward compatibility with
future products.
2: The C and DC bits operate as a Borrow
and Digit Borrow out bit, respectively, in
subtraction. See the SUBLW and SUBWF
instructions for examples.
For example, CLRF STATUS,will clear the upper three
bits and set the Z bit. This leaves the STATUS register
as ‘000u u1uu’(where u= unchanged).
REGISTER 2-1:
STATUS: STATUS REGISTER
Reserved
IRP
Reserved
RP1
R/W-0
RP0
R-1
TO
R-1
PD
R/W-x
Z
R/W-x
DC
R/W-x
C
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
bit 6
bit 5
IRP: This bit is reserved and should be maintained as ‘0’
RP1: This bit is reserved and should be maintained as ‘0’
RP0: Register Bank Select bit (used for direct addressing)
1= Bank 1 (80h – FFh)
0= Bank 0 (00h – 7Fh)
bit 4
bit 3
bit 2
bit 1
bit 0
TO: Time-out bit
1= After power-up, CLRWDTinstruction or SLEEPinstruction
0= A WDT time-out occurred
PD: Power-down bit
1= After power-up or by the CLRWDTinstruction
0= By execution of the SLEEPinstruction
Z: Zero bit
1= The result of an arithmetic or logic operation is zero
0= The result of an arithmetic or logic operation is not zero
DC: Digit Carry/Borrow bit (ADDWF, ADDLW,SUBLW,SUBWFinstructions), For Borrow, the polarity is reversed.
1= A carry-out from the 4th low-order bit of the result occurred
0= No carry-out from the 4th low-order bit of the result
(1)
C: Carry/Borrow bit (ADDWF, ADDLW, SUBLW, SUBWF instructions)
1= A carry-out from the Most Significant bit of the result occurred
0= No carry-out from the Most Significant bit of the result occurred
Note 1: For Borrow, the polarity is reversed. A subtraction is executed by adding the two’s complement of the second operand.
For rotate (RRF, RLF) instructions, this bit is loaded with either the high-order or low-order bit of the source register.
DS41288C-page 16
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
2.2.2.2
OPTION Register
Note:
To achieve a 1:1 prescaler assignment for
Timer0, assign the prescaler to the WDT
by setting PSA bit to ‘1’ of the OPTION
register. See Section 5.1.3 “Software
Programmable Prescaler”.
The OPTION register is a readable and writable regis-
ter, which contains various control bits to configure:
• Timer0/WDT prescaler
• External RA2/INT interrupt
• Timer0
• Weak pull-ups on PORTA
REGISTER 2-2:
OPTION_REG: OPTION REGISTER
R/W-1
RAPU
R/W-1
R/W-1
T0CS
R/W-1
T0SE
R/W-1
PSA
R/W-1
PS2
R/W-1
PS1
R/W-1
PS0
INTEDG
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2-0
RAPU: PORTA Pull-up Enable bit
1= PORTA pull-ups are disabled
0= PORTA pull-ups are enabled by individual PORT latch values
INTEDG: Interrupt Edge Select bit
1= Interrupt on rising edge of RA2/INT pin
0= Interrupt on falling edge of RA2/INT pin
T0CS: Timer0 Clock Source Select bit
1= Transition on RA2/T0CKI pin
0= Internal instruction cycle clock (FOSC/4)
T0SE: Timer0 Source Edge Select bit
1= Increment on high-to-low transition on RA2/T0CKI pin
0= Increment on low-to-high transition on RA2/T0CKI pin
PSA: Prescaler Assignment bit
1= Prescaler is assigned to the WDT
0= Prescaler is assigned to the Timer0 module
PS<2:0>: Prescaler Rate Select bits
BIT VALUE TIMER0 RATE WDT RATE
000
001
010
011
100
101
110
111
1 : 2
1 : 4
1 : 1
1 : 2
1 : 8
1 : 4
1 : 16
1 : 32
1 : 64
1 : 128
1 : 256
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 17
PIC16F610/616/16HV610/616
2.2.2.3
INTCON Register
Note:
Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the global
enable bit, GIE of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear
prior to enabling an interrupt.
The INTCON register is a readable and writable
register, which contains the various enable and flag bits
for TMR0 register overflow, PORTA change and
external RA2/INT pin interrupts.
REGISTER 2-3:
INTCON: INTERRUPT CONTROL REGISTER
R/W-0
GIE
R/W-0
PEIE
R/W-0
T0IE
R/W-0
INTE
R/W-0
RAIE
R/W-0
T0IF
R/W-0
INTF
R/W-0
RAIF
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
GIE: Global Interrupt Enable bit
1= Enables all unmasked interrupts
0= Disables all interrupts
PEIE: Peripheral Interrupt Enable bit
1= Enables all unmasked peripheral interrupts
0= Disables all peripheral interrupts
T0IE: Timer0 Overflow Interrupt Enable bit
1= Enables the Timer0 interrupt
0= Disables the Timer0 interrupt
INTE: RA2/INT External Interrupt Enable bit
1= Enables the RA2/INT external interrupt
0= Disables the RA2/INT external interrupt
RAIE: PORTA Change Interrupt Enable bit(1)
1= Enables the PORTA change interrupt
0= Disables the PORTA change interrupt
T0IF: Timer0 Overflow Interrupt Flag bit(2)
1= Timer0 register has overflowed (must be cleared in software)
0= Timer0 register did not overflow
INTF: RA2/INT External Interrupt Flag bit
1= The RA2/INT external interrupt occurred (must be cleared in software)
0= The RA2/INT external interrupt did not occur
RAIF: PORTA Change Interrupt Flag bit
1= When at least one of the PORTA <5:0> pins changed state (must be cleared in software)
0= None of the PORTA <5:0> pins have changed state
Note 1: IOCA register must also be enabled.
2: T0IF bit is set when TMR0 rolls over. TMR0 is unchanged on Reset and should be initialized before
clearing T0IF bit.
DS41288C-page 18
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
2.2.2.4
PIE1 Register
The PIE1 register contains the peripheral interrupt
enable bits, as shown in Register 2-4.
Note:
Bit PEIE of the INTCON register must be
set to enable any peripheral interrupt.
REGISTER 2-4:
PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1
U-0
—
R/W-0
ADIE(1)
R/W-0
CCP1IE(1)
R/W-0
C2IE
R/W-0
C1IE
U-0
—
R/W-0
TMR2IE(1)
R/W-0
TMR1IE
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
bit 6
Unimplemented: Read as ‘0’
ADIE: A/D Converter (ADC) Interrupt Enable bit(1)
1= Enables the ADC interrupt
0= Disables the ADC interrupt
bit 5
bit 4
bit 3
CCP1IE: CCP1 Interrupt Enable bit(1)
1= Enables the CCP1 interrupt
0= Disables the CCP1 interrupt
C2IE: Comparator C2 Interrupt Enable bit
1= Enables the Comparator C2 interrupt
0= Disables the Comparator C2 interrupt
C1IE: Comparator C1 Interrupt Enable bit
1= Enables the Comparator C1 interrupt
0= Disables the Comparator C1 interrupt
bit 2
bit 1
Unimplemented: Read as ‘0’
TMR2IE: Timer2 to PR2 Match Interrupt Enable bit(1)
1= Enables the Timer2 to PR2 match interrupt
0= Disables the Timer2 to PR2 match interrupt
bit 0
TMR1IE: Timer1 Overflow Interrupt Enable bit
1= Enables the Timer1 overflow interrupt
0= Disables the Timer1 overflow interrupt
Note 1: PIC16F616/16HV616 only. PIC16F610/16HV610 unimplemented, read as ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 19
PIC16F610/616/16HV610/616
2.2.2.5
PIR1 Register
The PIR1 register contains the peripheral interrupt flag
bits, as shown in Register 2-5.
Note:
Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the global
enable bit, GIE of the INTCON register. User
software should ensure the appropriate
interrupt flag bits are clear prior to enabling
an interrupt.
REGISTER 2-5:
PIR1: PERIPHERAL INTERRUPT REQUEST REGISTER 1
U-0
—
R/W-0
ADIF(1)
R/W-0
CCP1IF(1)
R/W-0
C2IF
R/W-0
C1IF
U-0
—
R/W-0
TMR2IF(1)
R/W-0
TMR1IF
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
bit 6
Unimplemented: Read as ‘0’
ADIF: A/D Interrupt Flag bit(1)
1= A/D conversion complete
0= A/D conversion has not completed or has not been started
CCP1IF: CCP1 Interrupt Flag bit(1)
bit 5
Capture mode:
1= A TMR1 register capture occurred (must be cleared in software)
0= No TMR1 register capture occurred
Compare mode:
1= A TMR1 register compare match occurred (must be cleared in software)
0= No TMR1 register compare match occurred
PWM mode:
Unused in this mode
bit 4
bit 3
C2IF: Comparator C2 Interrupt Flag bit
1= Comparator C2 output has changed (must be cleared in software)
0= Comparator C2 output has not changed
C1IF: Comparator C1 Interrupt Flag bit
1= Comparator C1 output has changed (must be cleared in software)
0= Comparator C1 output has not changed
bit 2
bit 1
Unimplemented: Read as ‘0’
TMR2IF: Timer2 to PR2 Match Interrupt Flag bit(1)
1= Timer2 to PR2 match occurred (must be cleared in software)
0= Timer2 to PR2 match has not occurred
bit 0
TMR1IF: Timer1 Overflow Interrupt Flag bit
1= Timer1 register overflowed (must be cleared in software)
0= Timer1 has not overflowed
Note 1: PIC16F616/16HV616 only. PIC16F610/16HV610 unimplemented, read as ‘0’.
DS41288C-page 20
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
2.2.2.6
PCON Register
The Power Control (PCON) register (see Table 12-2)
contains flag bits to differentiate between a:
• Power-on Reset (POR)
• Brown-out Reset (BOR)
• Watchdog Timer Reset (WDT)
• External MCLR Reset
The PCON register also controls the software enable of
the BOR.
The PCON register bits are shown in Register 2-6.
REGISTER 2-6:
PCON: POWER CONTROL REGISTER
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R/W-0
POR
R/W-0(1)
BOR
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-2
bit 1
Unimplemented: Read as ‘0’
POR: Power-on Reset Status bit
1= No Power-on Reset occurred
0= A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
bit 0
BOR: Brown-out Reset Status bit
1= No Brown-out Reset occurred
0= A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
Note 1: Reads as ‘0’ if Brown-out Reset is disabled.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 21
PIC16F610/616/16HV610/616
2.3.2
STACK
2.3
PCL and PCLATH
The PIC16F610/616/16HV610/616 Family has an
8-level x 13-bit wide hardware stack (see Figure 2-1).
The stack space is not part of either program or data
space and the Stack Pointer is not readable or writable.
The PC is PUSHed onto the stack when a CALL
instruction is executed or an interrupt causes a branch.
The stack is POPed in the event of a RETURN, RETLW
or a RETFIE instruction execution. PCLATH is not
affected by a PUSH or POP operation.
The Program Counter (PC) is 13 bits wide. The low byte
comes from the PCL register, which is a readable and
writable register. The high byte (PC<12:8>) is not directly
readable or writable and comes from PCLATH. On any
Reset, the PC is cleared. Figure 2-5 shows the two
situations for the loading of the PC. The upper example
in Figure 2-5 shows how the PC is loaded on a write to
PCL (PCLATH<4:0> → PCH). The lower example in
Figure 2-5 shows how the PC is loaded during a CALLor
GOTOinstruction (PCLATH<4:3> → PCH).
The stack operates as a circular buffer. This means that
after the stack has been PUSHed eight times, the ninth
push overwrites the value that was stored from the first
push. The tenth push overwrites the second push (and
so on).
FIGURE 2-5:
LOADING OF PC IN
DIFFERENT SITUATIONS
PCH
PCL
Instruction with
Note 1: There are no Status bits to indicate stack
12
8
7
0
PCL as
overflow or stack underflow conditions.
Destination
PC
2: There are no instructions/mnemonics
called PUSH or POP. These are actions
that occur from the execution of the
CALL, RETURN, RETLW and RETFIE
instructions or the vectoring to an
interrupt address.
8
PCLATH<4:0>
PCLATH
5
ALU Result
PCH
12 11 10
PC
PCL
8
7
0
GOTO, CALL
2.4
Indirect Addressing, INDF and
FSR Registers
PCLATH<4:3>
PCLATH
11
2
OPCODE <10:0>
The INDF register is not a physical register. Addressing
the INDF register will cause indirect addressing.
Indirect addressing is possible by using the INDF
register. Any instruction using the INDF register
actually accesses data pointed to by the File Select
Register (FSR). Reading INDF itself indirectly will
produce 00h. Writing to the INDF register indirectly
results in a no operation (although Status bits may be
affected). An effective 9-bit address is obtained by
concatenating the 8-bit FSR and the IRP bit of the
STATUS register, as shown in Figure 2-7.
2.3.1
MODIFYING PCL
Executing any instruction with the PCL register as the
destination simultaneously causes the Program
Counter PC<12:8> bits (PCH) to be replaced by the
contents of the PCLATH register. This allows the entire
contents of the program counter to be changed by
writing the desired upper 5 bits to the PCLATH register.
When the lower 8 bits are written to the PCL register, all
13 bits of the program counter will change to the values
contained in the PCLATH register and those being
written to the PCL register.
A simple program to clear RAM location 40h-4Fh using
indirect addressing is shown in Example 2-1.
EXAMPLE 2-1:
INDIRECT ADDRESSING
A computed GOTOis accomplished by adding an offset
to the program counter (ADDWF PCL). Care should be
exercised when jumping into a look-up table or
program branch table (computed GOTO) by modifying
the PCL register. Assuming that PCLATH is set to the
table start address, if the table length is greater than
255 instructions or if the lower 8 bits of the memory
address rolls over from 0xFF to 0x00 in the middle of
the table, then PCLATH must be incremented for each
address rollover that occurs between the table
beginning and the target location within the table.
MOVLW
MOVWF
0x40
FSR
;initialize pointer
;to RAM
NEXT
CLRF
INCF
BTFSS
GOTO
INDF
;clear INDF register
FSR, F ;inc pointer
FSR,4
NEXT
;all done?
;no clear next
;yes continue
CONTINUE
For more information refer to Application Note AN556,
“Implementing a Table Read” (DS00556).
DS41288C-page 22
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
FIGURE 2-6:
DIRECT/INDIRECT ADDRESSING PIC16F610/16HV610
Direct Addressing
From Opcode
Indirect Addressing
(1)
(1)
7
RP1 RP0
6
0
0
IRP
File Select Register
Bank Select
180h
Location Select
Bank Select
Location Select
00h
00
01
10
11
(2)
Data
Memory
NOT USED
20h
40h
70h
7Fh
1FFh
Bank 0
Bank 1
Bank 2
Bank 3
For memory map detail, see Figure 2-3.
Unimplemented data memory locations, read as ‘0’.
Note 1: The RP1 and IRP bits are reserved; always maintain these bits clear.
2: Accesses in Bank 2 and Bank 3 are mirrored back into Bank 0 and Bank 1, respectively.
FIGURE 2-7:
DIRECT/INDIRECT ADDRESSING PIC16F616/16HV616
Direct Addressing
Indirect Addressing
(1)
(1)
From Opcode
7
RP1 RP0
6
0
0
IRP
File Select Register
Bank Select
180h
Location Select
Bank Select
Location Select
00h
00
01
10
11
(2)
Data
Memory
NOT USED
40h
70h
7Fh
1FFh
Bank 0
Bank 1
Bank 2
Bank 3
For memory map detail, see Figure 2-4.
Unimplemented data memory locations, read as ‘0’.
Note 1: The RP1 and IRP bits are reserved; always maintain these bits clear.
2: Accesses in Bank 2 and Bank 3 are mirrored back into Bank 0 and Bank 1, respectively.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 23
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 24
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
The Oscillator module can be configured in one of eight
clock modes.
3.0
3.1
OSCILLATOR MODULE
Overview
1. EC – External clock with I/O on OSC2/CLKOUT.
2. LP – 32 kHz Low-Power Crystal mode.
The Oscillator module has a wide variety of clock
sources and selection features that allow it to be used
in a wide range of applications while maximizing perfor-
mance and minimizing power consumption. Figure 3-1
illustrates a block diagram of the Oscillator module.
3. XT – Medium Gain Crystal or Ceramic Resonator
Oscillator mode.
4. HS – High Gain Crystal or Ceramic Resonator
mode.
5. RC – External Resistor-Capacitor (RC) with
FOSC/4 output on OSC2/CLKOUT.
Clock sources can be configured from external
oscillators, quartz crystal resonators, ceramic resonators
and Resistor-Capacitor (RC) circuits. In addition, the
system clock source can be configured with a choice of
two selectable speeds: internal or external system clock
source.
6. RCIO – External Resistor-Capacitor (RC) with
I/O on OSC2/CLKOUT.
7. INTOSC – Internal oscillator with FOSC/4 output
on OSC2 and I/O on OSC1/CLKIN.
8. INTOSCIO – Internal oscillator with I/O on
OSC1/CLKIN and OSC2/CLKOUT.
Clock Source modes are configured by the FOSC<2:0>
bits in the Configuration Word register (CONFIG). The
Internal Oscillator module provides a selectable system
clock mode of either 4 MHz (Postscaler) or 8 MHz
(INTOSC).
FIGURE 3-1:
PIC® MCU CLOCK SOURCE BLOCK DIAGRAM
FOSC<2:0>
IOSCFS
(Configuration Word Register)
External Oscillator
OSC2
OSC1
Sleep
LP, XT, HS, RC, RCIO, EC
INTOSC
System Clock
(CPU and Peripherals)
Internal Oscillator
INTOSC
8 MHz
Postscaler
4 MHz
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 25
PIC16F610/616/16HV610/616
3.3.2
OSCILLATOR START-UP TIMER
(OST)
3.2
Clock Source Modes
Clock Source modes can be classified as external or
internal.
If the Oscillator module is configured for LP, XT or HS
modes, the Oscillator Start-up Timer (OST) counts
1024 oscillations from OSC1. This occurs following a
Power-on Reset (POR) and when the Power-up Timer
(PWRT) has expired (if configured), or a wake-up from
Sleep. During this time, the program counter does not
increment and program execution is suspended. The
OST ensures that the oscillator circuit, using a quartz
crystal resonator or ceramic resonator, has started and
is providing a stable system clock to the Oscillator
module. When switching between clock sources, a
delay is required to allow the new clock to stabilize.
These oscillator delays are shown in Table 3-1.
• External Clock modes rely on external circuitry for
the clock source. Examples are: Oscillator mod-
ules (EC mode), quartz crystal resonators or
ceramic resonators (LP, XT and HS modes) and
Resistor-Capacitor (RC) mode circuits.
• Internal clock sources are contained internally
within the Oscillator module. The Oscillator
module has two selectable clock frequencies:
4 MHz and 8 MHz
The system clock can be selected between external or
internal clock sources via the FOSC<2:0> bits of the
Configuration Word register.
3.3
External Clock Modes
3.3.1
EC MODE
The External Clock (EC) mode allows an externally
generated logic level as the system clock source. When
operating in this mode, an external clock source is
connected to the OSC1 input and the OSC2 is available
for general purpose I/O. Figure 3-2 shows the pin
connections for EC mode.
The Oscillator Start-up Timer (OST) is disabled when
EC mode is selected. Therefore, there is no delay in
operation after a Power-on Reset (POR) or wake-up
from Sleep. Because the PIC® MCU design is fully
static, stopping the external clock input will have the
effect of halting the device while leaving all data intact.
Upon restarting the external clock, the device will
resume operation as if no time had elapsed.
FIGURE 3-2:
EXTERNAL CLOCK (EC)
MODE OPERATION
OSC1/CLKIN
Clock from
Ext. System
PIC® MCU
(1)
I/O
OSC2/CLKOUT
Note 1: Alternate pin functions are listed in the
Section 1.0 “Device Overview”.
TABLE 3-1:
Switch From
OSCILLATOR DELAY EXAMPLES
Switch To
Frequency
Oscillator Delay
Sleep/POR
Sleep/POR
Sleep/POR
INTOSC
EC, RC
4 MHz to 8 MHz
DC – 20 MHz
Oscillator Warm-Up Delay (TWARM)
2 Instruction Cycles
LP, XT, HS
32 kHz to 20 MHz
1024 Clock Cycles (OST)
DS41288C-page 26
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
3.3.3
LP, XT, HS MODES
Note 1: Quartz crystal characteristics vary according
The LP, XT and HS modes support the use of quartz
crystal resonators or ceramic resonators connected to
OSC1 and OSC2 (Figure 3-3). The mode selects a low,
medium or high gain setting of the internal inverter-
amplifier to support various resonator types and speed.
to type, package and manufacturer. The
user should consult the manufacturer data
sheets for specifications and recommended
application.
2: Always verify oscillator performance over
the VDD and temperature range that is
expected for the application.
LP Oscillator mode selects the lowest gain setting of
the internal inverter-amplifier. LP mode current
consumption is the least of the three modes. This mode
is designed to drive only 32.768 kHz tuning-fork type
crystals (watch crystals).
3: For oscillator design assistance, reference
the following Microchip Applications Notes:
• AN826, “Crystal Oscillator Basics and
Crystal Selection for rfPIC® and PIC®
Devices” (DS00826)
• AN849, “Basic PIC® Oscillator Design”
(DS00849)
• AN943, “Practical PIC® Oscillator
XT Oscillator mode selects the intermediate gain
setting of the internal inverter-amplifier. XT mode
current consumption is the medium of the three modes.
This mode is best suited to drive resonators with a
medium drive level specification.
HS Oscillator mode selects the highest gain setting of
the internal inverter-amplifier. HS mode current
consumption is the highest of the three modes. This
mode is best suited for resonators that require a high
drive setting.
Analysis and Design” (DS00943)
• AN949, “Making Your Oscillator Work”
(DS00949)
FIGURE 3-4:
CERAMIC RESONATOR
OPERATION
Figure 3-3 and Figure 3-4 show typical circuits for
quartz crystal and ceramic resonators, respectively.
(XT OR HS MODE)
FIGURE 3-3:
QUARTZ CRYSTAL
OPERATION (LP, XT OR
HS MODE)
PIC® MCU
OSC1/CLKIN
C1
PIC® MCU
To Internal
Logic
OSC1/CLKIN
(3)
(2)
RP
RF
Sleep
C1
To Internal
Logic
Quartz
Crystal
(2)
OSC2/CLKOUT
(1)
C2
RF
Sleep
RS
Ceramic
Resonator
Note 1: A series resistor (RS) may be required for
OSC2/CLKOUT
(1)
C2
RS
ceramic resonators with low drive level.
2: The value of RF varies with the Oscillator mode
selected (typically between 2 MΩ to 10 MΩ).
Note 1: A series resistor (RS) may be required for
quartz crystals with low drive level.
3: An additional parallel feedback resistor (RP)
may be required for proper ceramic resonator
operation.
2: The value of RF varies with the Oscillator mode
selected (typically between 2 MΩ to 10 MΩ).
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 27
PIC16F610/616/16HV610/616
3.3.4
EXTERNAL RC MODES
3.4
Internal Clock Modes
The external Resistor-Capacitor (RC) modes support
the use of an external RC circuit. This allows the
designer maximum flexibility in frequency choice while
keeping costs to a minimum when clock accuracy is not
required. There are two modes: RC and RCIO.
The Oscillator module provides a selectable system
clock source of either 4 MHz or 8 MHz. The selectable
frequency is configured through the IOSCFS bit of the
Configuration Word.
The frequency of the internal oscillator can be can be
user-adjusted via software using the OSCTUNE
register.
In RC mode, the RC circuit connects to OSC1. OSC2/
CLKOUT outputs the RC oscillator frequency divided
by 4. This signal may be used to provide a clock for
external circuitry, synchronization, calibration, test or
other application requirements. Figure 3-5 shows the
external RC mode connections.
3.4.1 INTOSC AND INTOSCIO MODES
The INTOSC and INTOSCIO modes configure the
internal oscillators as the system clock source when
the device is programmed using the oscillator selection
or the FOSC<2:0> bits in the Configuration Word
register (CONFIG). See Section 12.0 “Special
Features of the CPU” for more information.
FIGURE 3-5:
EXTERNAL RC MODES
VDD
PIC® MCU
In INTOSC mode, OSC1/CLKIN is available for general
purpose I/O. OSC2/CLKOUT outputs the selected
internal oscillator frequency divided by 4. The CLKOUT
signal may be used to provide a clock for external
circuitry, synchronization, calibration, test or other
application requirements.
REXT
OSC1/CLKIN
Internal
Clock
CEXT
VSS
In INTOSCIO mode, OSC1/CLKIN and OSC2/CLKOUT
are available for general purpose I/O.
(1)
FOSC/4 or
I/O
OSC2/CLKOUT
(2)
Recommended values: 10 kΩ ≤ REXT ≤ 100 kΩ, <3V
3 kΩ ≤ REXT ≤ 100 kΩ, 3-5V
CEXT > 20 pF, 2-5V
Note 1: Alternate pin functions are listed in
Section 1.0 “Device Overview”.
2: Output depends upon RC or RCIO Clock
mode.
In RCIO mode, the RC circuit is connected to OSC1.
OSC2 becomes an additional general purpose I/O pin.
The RC oscillator frequency is a function of the supply
voltage, the resistor (REXT) and capacitor (CEXT) values
and the operating temperature. Other factors affecting
the oscillator frequency are:
• threshold voltage variation
• component tolerances
• packaging variations in capacitance
The user also needs to take into account variation due
to tolerance of external RC components used.
DS41288C-page 28
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
The default value of the OSCTUNE register is ‘0’. The
value is a 5-bit two’s complement number.
3.4.1.1
OSCTUNE Register
The oscillator is factory calibrated but can be adjusted
in software by writing to the OSCTUNE register
(Register 3-1).
When the OSCTUNE register is modified, the frequency
will begin shifting to the new frequency. Code execution
continues during this shift. There is no indication that the
shift has occurred.
REGISTER 3-1:
OSCTUNE: OSCILLATOR TUNING REGISTER
U-0
—
U-0
—
U-0
—
R/W-0
TUN4
R/W-0
TUN3
R/W-0
TUN2
R/W-0
TUN1
R/W-0
TUN0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-5
bit 4-0
Unimplemented: Read as ‘0’
TUN<4:0>: Frequency Tuning bits
01111= Maximum frequency
01110=
•
•
•
00001=
00000= Oscillator module is running at the manufacturer calibrated frequency.
11111=
•
•
•
10000= Minimum frequency
TABLE 3-2:
SUMMARY OF REGISTERS ASSOCIATED WITH CLOCK SOURCES
Value on
all other
Resets
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(1)
(2)
CONFIG
IOSCFS
—
CP
—
MCLRE PWRTE
TUN4
WDTE
TUN3
FOSC2
TUN2
FOSC1
TUN1
FOSC0
TUN0
—
—
OSCTUNE
—
---0 0000 ---u uuuu
Legend:
x= unknown, u= unchanged, –= unimplemented locations read as ‘0’. Shaded cells are not used by oscillators.
Note 1: Other (non Power-up) Resets include MCLR Reset and Watchdog Timer Reset during normal operation.
2: See Configuration Word register (Register 12-1) for operation of all register bits.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 29
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 30
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
port pins are read, this value is modified and then
written to the PORT data latch. RA3 reads ‘0’ when
4.0
I/O PORTS
There are as many as eleven general purpose I/O pins
and an input pin available. Depending on which
peripherals are enabled, some or all of the pins may not
be available as general purpose I/O. In general, when a
peripheral is enabled, the associated pin may not be
used as a general purpose I/O pin.
MCLRE = 1.
The TRISA register controls the direction of the
PORTA pins, even when they are being used as analog
inputs. The user must ensure the bits in the TRISA
register are maintained set when using them as analog
inputs. I/O pins configured as analog input always read
‘0’.
4.1
PORTA and the TRISA Registers
Note:
The ANSEL register must be initialized to
configure an analog channel as a digital
input. Pins configured as analog inputs will
read ‘0’ and cannot generate an interrupt.
PORTA is
a 6-bit wide, bidirectional port. The
corresponding data direction register is TRISA
(Register 4-2). Setting a TRISA bit (= 1) will make the
corresponding PORTA pin an input (i.e., disable the
output driver). Clearing a TRISA bit (= 0) will make the
corresponding PORTA pin an output (i.e., enables output
driver and puts the contents of the output latch on the
selected pin). The exception is RA3, which is input only
and its TRIS bit will always read as ‘1’. Example 4-1
shows how to initialize PORTA.
EXAMPLE 4-1:
INITIALIZING PORTA
BCF
STATUS,RP0
;Bank 0
;Init PORTA
;Bank 1
;digital I/O
;Set RA<3:2> as inputs
;and set RA<5:4,1:0>
;as outputs
;Bank 0
CLRF
BSF
CLRF
PORTA
STATUS,RP0
ANSEL
MOVLW 0Ch
MOVWF TRISA
Reading the PORTA register (Register 4-1) reads the
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
BCF
STATUS,RP0
REGISTER 4-1:
PORTA: PORTA REGISTER
U-0
—
U-0
—
R/W-x
RA5
R/W-0
RA4
R-x
R/W-0
RA2
R/W-0
RA1
R/W-0
RA0
RA3
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RA<5:0>: PORTA I/O Pin bit
1= PORTA pin is > VIH
0= PORTA pin is < VIL
REGISTER 4-2:
TRISA: PORTA TRI-STATE REGISTER
U-0
—
U-0
—
R/W-1
R/W-1
R-1
R/W-1
R/W-1
R/W-1
TRISA5
TRISA4
TRISA3
TRISA2
TRISA1
TRISA0
bit 0
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
TRISA<5:0>: PORTA Tri-State Control bit
1= PORTA pin configured as an input (tri-stated)
0= PORTA pin configured as an output
Note 1: TRISA<3> always reads ‘1’.
2: TRISA<5:4> always reads ‘1’ in XT, HS and LP Oscillator modes.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 31
PIC16F610/616/16HV610/616
4.2.3
INTERRUPT-ON-CHANGE
4.2
Additional Pin Functions
Each PORTA pin is individually configurable as an
interrupt-on-change pin. Control bits IOCAx enable or
disable the interrupt function for each pin. Refer to
Register 4-5. The interrupt-on-change is disabled on a
Power-on Reset.
Every PORTA pin on the PIC16F610/616/16HV610/
616 has an interrupt-on-change option and a weak pull-
up option. The next three sections describe these
functions.
4.2.1
ANSEL REGISTER
For enabled interrupt-on-change pins, the values are
compared with the old value latched on the last read of
PORTA. The ‘mismatch’ outputs of the last read are
OR’d together to set the PORTA Change Interrupt Flag
bit (RAIF) in the INTCON register (Register 2-3).
The ANSEL register is used to configure the Input
mode of an I/O pin to analog. Setting the appropriate
ANSEL bit high will cause all digital reads on the pin to
be read as ‘0’ and allow analog functions on the pin to
operate correctly.
This interrupt can wake the device from Sleep. The
user, in the Interrupt Service Routine, clears the
interrupt by:
The state of the ANSEL bits has no affect on digital
output functions. A pin with TRIS clear and ANSEL set
will still operate as a digital output, but the Input mode
will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
affected port.
a) Any read or write of PORTA. This will end the
mismatch condition, then,
b) Clear the flag bit RAIF.
A mismatch condition will continue to set flag bit RAIF.
Reading PORTA will end the mismatch condition and
allow flag bit RAIF to be cleared. The latch holding the
last read value is not affected by a MCLR nor BOR
Reset. After these resets, the RAIF flag will continue to
be set if a mismatch is present.
4.2.2
WEAK PULL-UPS
Each of the PORTA pins, except RA3, has an
individually configurable internal weak pull-up. Control
bits WPUAx enable or disable each pull-up. Refer to
Register 4-4. Each weak pull-up is automatically turned
off when the port pin is configured as an output. The
pull-ups are disabled on a Power-on Reset by the
RAPU bit of the OPTION register). A weak pull-up is
automatically enabled for RA3 when configured as
MCLR and disabled when RA3 is an I/O. There is no
software control of the MCLR pull-up.
Note:
If a change on the I/O pin should occur
when any PORTA operation is being
executed, then the RAIF interrupt flag may
not get set.
REGISTER 4-3:
ANSEL: ANALOG SELECT REGISTER
R/W-1
ANS7
R/W-1
ANS6
R/W-1
ANS5
R/W-1
ANS4
R/W-1
ANS3
R/W-1
ANS2
R/W-1
ANS1
R/W-1
ANS0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-0
ANS<7:0>: Analog Select bits
Analog select between analog or digital function on pins AN<7:0>, respectively.
1= Analog input. Pin is assigned as analog input(1)
0= Digital I/O. Pin is assigned to port or special function.
.
Note 1: Setting a pin to an analog input automatically disables the digital input circuitry, weak pull-ups, and
interrupt-on-change if available. The corresponding TRIS bit must be set to Input mode in order to allow
external control of the voltage on the pin.
DS41288C-page 32
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
REGISTER 4-4:
WPUA: WEAK PULL-UP PORTA REGISTER
U-0
—
U-0
—
R/W-1
R/W-1
U-0
—
R/W-1
R/W-1
R/W-1
WPUA5
WPUA4
WPUA2
WPUA1
WPUA0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-6
bit 5-4
Unimplemented: Read as ‘0’
WPUA<5:4>: Weak Pull-up Control bits
1= Pull-up enabled
0= Pull-up disabled
bit 3
Unimplemented: Read as ‘0’
bit 2-0
WPUA<2:0>: Weak Pull-up Control bits
1= Pull-up enabled
0= Pull-up disabled
Note 1: Global RAPU must be enabled for individual pull-ups to be enabled.
2: The weak pull-up device is automatically disabled if the pin is in Output mode (TRISA = 0).
3: The RA3 pull-up is enabled when configured as MCLR and disabled as an input in the Configuration
Word.
4: WPUA<5:4> always reads ‘1’ in XT, HS and LP Oscillator modes.
REGISTER 4-5:
IOCA: INTERRUPT-ON-CHANGE PORTA REGISTER
U-0
—
U-0
—
R/W-0
IOCA5
R/W-0
IOCA4
R/W-0
IOCA3
R/W-0
IOCA2
R/W-0
IOCA1
R/W-0
IOCA0
bit 0
bit 7
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
IOCA<5:0>: Interrupt-on-change PORTA Control bit
1= Interrupt-on-change enabled
0= Interrupt-on-change disabled
Note 1: Global Interrupt Enable (GIE) must be enabled for individual interrupts to be recognized.
2: IOCA<5:4> always reads ‘1’ in XT, HS and LP Oscillator modes.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 33
PIC16F610/616/16HV610/616
(1)
4.2.4
PIN DESCRIPTIONS AND
DIAGRAMS
4.2.4.2
RA1/AN1(1)/C12IN0-/VREF
ICSPCLK
/
Each PORTA pin is multiplexed with other functions.
The pins and their combined functions are briefly
described here. For specific information about
individual functions such as the Comparator or the
ADC, refer to the appropriate section in this data sheet.
Figure 4-1 shows the diagram for this pin. The RA1 pin
is configurable to function as one of the following:
• a general purpose I/O
(1)
• an analog input for the ADC
• an analog inverting input to the comparator
RA0/AN0(1)/C1IN+/ICSPDAT
(1)
4.2.4.1
• a voltage reference input for the ADC
• In-Circuit Serial Programming clock
Figure 4-1 shows the diagram for this pin. The RA0 pin
is configurable to function as one of the following:
Note 1: PIC16F616/16HV616 only.
• a general purpose I/O
(1)
• an analog input for the ADC
• an analog non-inverting input to the comparator
• In-Circuit Serial Programming data
FIGURE 4-1:
BLOCK DIAGRAM OF RA<1:0>
Analog(1)
Input Mode
VDD
Data Bus
D
Q
Q
Weak
CK
WR
WPUA
RAPU
VDD
RD
WPUA
D
Q
Q
I/O Pin
WR
CK
PORTA
VSS
D
Q
Q
WR
TRISA
CK
RD
TRISA
Analog(1)
Input Mode
RD
PORTA
D
Q
Q
Q
Q
D
CK
WR
IOCA
Q1
EN
RD
IOCA
D
S(2)
R
EN
Q
Interrupt-on-
Change
From other
RA<5:1> pins (RA0)
RD PORTA
RA<5:2, 0> pins (RA1)
To Comparator
To A/D Converter(3)
Write ‘0’ to RAIF
Note 1: Comparator mode and ANSEL determines Analog Input mode.
2: Set has priority over Reset.
3: PIC16F616/16HV616 only.
DS41288C-page 34
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
4.2.4.3
RA2/AN2(1)/T0CKI/INT/C1OUT
Figure 4-2 shows the diagram for this pin. The RA2 pin
is configurable to function as one of the following:
• a general purpose I/O
(1)
• an analog input for the ADC
• the clock input for TMR0
• an external edge triggered interrupt
• a digital output from Comparator C1
Note 1: PIC16F616/16HV616 only.
FIGURE 4-2:
BLOCK DIAGRAM OF RA2
Analog(1)
Input Mode
VDD
Data Bus
D
Q
Q
Weak
CK
WR
WPUA
C1OE
Enable
RAPU
VDD
RD
WPUA
C1OE
1
0
D
Q
Q
I/O Pin
WR
CK
VSS
PORTA
D
Q
Q
WR
TRISA
CK
RD
TRISA
Analog(1)
Input Mode
RD
PORTA
D
Q
Q
Q
D
D
CK
WR
IOAC
Q1
EN
RD
IOAC
Q
S(2)
R
EN
Q
Interrupt-on-
Change
From other
RA<5:3, 1:0> pins
RD PORTA
To Timer0
To INT
Write ‘0’ to RAIF
To A/D Converter(3)
Note 1: Comparator mode and ANSEL determines Analog Input mode.
2: Set has priority over Reset.
3: PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 35
PIC16F610/616/16HV610/616
4.2.4.4
RA3/MCLR/VPP
Figure 4-3 shows the diagram for this pin. The RA3 pin
is configurable to function as one of the following:
• a general purpose input
• as Master Clear Reset with weak pull-up
FIGURE 4-3:
BLOCK DIAGRAM OF RA3
VDD
MCLRE
Weak
Data Bus
MCLRE
Reset
Input
Pin
RD
TRISA
VSS
MCLRE
VSS
RD
PORTA
D
Q
Q
Q
Q
D
CK
WR
IOCA
Q1
EN
RD
IOCA
D
(1)
Q
S
EN
Interrupt-on-
Change
From other
RA<5:4, 2:0> pins
R
RD PORTA
Write ‘0’ to RAIF
Note 1: Set has priority over Reset
DS41288C-page 36
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
RA4/AN3(1)/T1G/OSC2/CLKOUT
• a Timer1 gate (count enable)
4.2.4.5
• a crystal/resonator connection
• a clock output
Figure 4-4 shows the diagram for this pin. The RA4 pin
is configurable to function as one of the following:
Note 1: PIC16F616/16HV616 only.
• a general purpose I/O
(1)
• an analog input for the ADC
FIGURE 4-4:
BLOCK DIAGRAM OF RA4
(3)
Analog
Input Mode
(1)
CLK
Modes
Data Bus
D
Q
Q
VDD
WR
CK
Weak
WPUA
RAPU
RD
WPUA
Oscillator
Circuit
OSC1
VDD
CLKOUT
Enable
FOSC/4
1
0
D
Q
Q
I/O Pin
WR
CK
PORTA
CLKOUT
Enable
VSS
D
Q
Q
INTOSC/
(2)
RC/EC
WR
TRISA
CK
CLKOUT
Enable
RD
TRISA
Analog
Input Mode
RD
PORTA
D
Q
Q
Q
D
D
CK
WR
IOCA
Q1
EN
RD
IOCA
Q
(4)
EN
Q
S
Interrupt-on-
Change
From other
RA<5, 3:0> pins
R
RD PORTA
To T1G
To A/D Converter
Write ‘0’ to RAIF
(5)
Note 1: CLK modes are XT, HS, LP, TMR1 LP and CLKOUT Enable.
2: With CLKOUT option.
3: Analog Input mode comes from ANSEL.
4: Set has priority over Reset.
5: PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 37
PIC16F610/616/16HV610/616
• a general purpose I/O
• a Timer1 clock input
• a crystal/resonator connection
• a clock input
4.2.4.6
RA5/T1CKI/OSC1/CLKIN
Figure 4-5 shows the diagram for this pin. The RA5 pin
is configurable to function as one of the following:
FIGURE 4-5:
BLOCK DIAGRAM OF RA5
INTOSC
Mode
(1)
TMR1LPEN
Data Bus
D
VDD
Q
Q
WR
CK
Weak
WPUA
RAPU
RD
WPUA
Oscillator
Circuit
OSC2
VDD
D
Q
Q
WR
PORTA
CK
I/O Pin
D
Q
Q
WR
CK
VSS
TRISA
INTOSC
Mode
RD
TRISA
RD
PORTA
D
Q
Q
Q
D
D
CK
WR
IOCA
Q1
EN
RD
IOCA
Q
(2)
Q
S
EN
Interrupt-on-
Change
From other
RA<4:0> pins
R
RD PORTA
Write ‘0’ to RAIF
To Timer1
Note 1: Timer1 LP Oscillator enabled.
2: Set has priority over Reset.
DS41288C-page 38
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 4-1:
SUMMARY OF REGISTERS ASSOCIATED WITH PORTA
Value on
all other
Resets
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ANSEL
ANS7
C1ON
C2ON
GIE
ANS6
C1OUT
C2OUT
PEIE
ANS5
C1OE
C2OE
T0IE
ANS4
C1POL
C2POL
INTE
ANS3
—
ANS2
C1R
ANS1
ANS0
1111 1111
0000 -000
0000 -000
0000 0000
--00 0000
1111 1111
--x0 x000
1111 1111
0000 -000
0000 -000
0000 0000
--00 0000
1111 1111
--u0 u000
--11 1111
--11 -111
CM1CON0
CM2CON0
INTCON
IOCA
C1CH1 C1CH0
C2CH1 C2CH0
—
C2R
RAIE
IOCA3
PSA
T0IF
IOCA2
PS2
INTF
IOCA1
PS1
RAIF
IOCA0
PS0
—
—
IOCA5
IOCA4
T0SE
OPTION_REG RAPU INTEDG T0CS
PORTA
TRISA
—
—
—
—
—
—
RA5
RA4
RA3
RA2
RA1
RA0
TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 --11 1111
WPUA5 WPUA4 WPUA2 WPUA1 WPUA0 --11 -111
WPUA
Legend:
—
x= unknown, u= unchanged, – = unimplemented locations read as ‘0’. Shaded cells are not used by PORTA.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 39
PIC16F610/616/16HV610/616
EXAMPLE 4-2:
INITIALIZING PORTC
4.3
PORTC and the TRISC Registers
BCF
CLRF
BSF
CLRF
MOVLW
MOVWF
STATUS,RP0
PORTC
STATUS,RP0
ANSEL
0Ch
;Bank 0
;Init PORTC
;Bank 1
;digital I/O
;Set RC<3:2> as inputs
;and set RC<5:4,1:0>
;as outputs
PORTC is a general purpose I/O port consisting of 6
bidirectional pins. The pins can be configured for either
digital I/O or analog input to A/D Converter (ADC) or
Comparator. For specific information about individual
functions such as the Enhanced CCP or the ADC, refer
to the appropriate section in this data sheet.
TRISC
BCF
STATUS,RP0
;Bank 0
Note:
The ANSEL register must be initialized to
configure an analog channel as a digital
input. Pins configured as analog inputs will
read ‘0’ and cannot generate an interrupt.
REGISTER 4-6:
PORTC: PORTC REGISTER
U-0
—
U-0
—
R/W-x
RC5
R/W-x
RC4
R/W-0
RC3
R/W-0
RC2
R/W-x
RC1
R/W-x
RC0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
RC<5:0>: PORTC I/O Pin bit
1= PORTC pin is > VIH
0= PORTC pin is < VIL
REGISTER 4-7:
TRISC: PORTC TRI-STATE REGISTER
U-0
—
U-0
—
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
TRISC5
TRISC4
TRISC3
TRISC2
TRISC1
TRISC0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-6
bit 5-0
Unimplemented: Read as ‘0’
TRISC<5:0>: PORTC Tri-State Control bit
1= PORTC pin configured as an input (tri-stated)
0= PORTC pin configured as an output
DS41288C-page 40
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
4.3.1
RC0/AN4(1)/C2IN+
4.3.3
RC2/AN6(1)/C12IN2-/P1D(1)
The RC0 is configurable to function as one of the
following:
The RC2 is configurable to function as one of the
following:
• a general purpose I/O
• a general purpose I/O
(1)
(1)
• an analog input for the ADC
• an analog input for the ADC
• an analog non-inverting input to Comparator C2
• an analog input to Comparators C1 and C2
(1)
• a digital output from the Enhanced CCP
4.3.2
RC1/AN5(1)/C12IN1-
4.3.4
RC3/AN7(1)/C12IN3-/P1C(1)
The RC1 is configurable to function as one of the
following:
The RC3 is configurable to function as one of the
following:
• a general purpose I/O
(1)
• an analog input for the ADC
• a general purpose I/O
(1)
• an analog inverting input to the comparator
• an analog input for the ADC
Note 1: PIC16F616/16HV616 only.
• an analog inverting input to Comparators C1 and C2
(1)
• a digital output from the Enhanced CCP
FIGURE 4-6:
BLOCK DIAGRAM OF RC0
AND RC1
Note 1: PIC16F616/16HV616 only.
Data Bus
FIGURE 4-7:
BLOCK DIAGRAM OF RC2
AND RC3
VDD
D
Q
Q
Data Bus
CCPOUT(2)
Enable
WR
PORTC
CK
VDD
D
CK
Q
Q
I/O Pin
WR
PORTC
CCPOUT
1
0
D
Q
Q
WR
TRISC
CK
I/O Pin
VSS
Analog Input
D
Q
Q
Mode(1)
WR
TRISC
CK
RD
TRISC
VSS
Analog Input
Mode(1)
RD
TRISC
RD
PORTC
To Comparators
To A/D Converter
RD
PORTC
To A/D Converter
Note 1: Analog Input mode comes from ANSEL or
Comparator mode.
Note 1: Analog Input mode comes from ANSEL.
2: PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 41
PIC16F610/616/16HV610/616
4.3.5
RC4/C2OUT/P1B(1)
4.3.6
RC5/CCP1(1)/P1A(1)
The RC4 is configurable to function as one of the
following:
The RC5 is configurable to function as one of the
following:
• a general purpose I/O
• a general purpose I/O
• a digital input/output for the Enhanced CCP
(1)
• a digital output from Comparator C2
(1)
Note 1: PIC16F616/16HV616 only.
• a digital output from the Enhanced CCP
Note 1: PIC16F616/16HV616 only.
FIGURE 4-9:
BLOCK DIAGRAM OF RC5
PIN
2: Enabling both C2OUT and P1B will cause
a conflict on RC4 and create unpredictable
results. Therefore, if C2OUT is enabled,
the ECCP can not be used in Half-Bridge
or Full-Bridge mode and vice-versa.
Data bus
CCP1OUT(1)
Enable
VDD
D
CK
Q
Q
WR
PORTC
FIGURE 4-8:
BLOCK DIAGRAM OF RC4
CCP1OUT(1)
P1A
/
1
0
C2OE
CCP1M<3:0>
I/O Pin
D
Q
Q
C2OE
C2OUT
VDD
WR
TRISC
CK
VSS
CCP1M<3:0>
CCPOUT/P1B
1
RD
TRISC
0
Data Bus
D
I/O Pin
Q
Q
RD
PORTC
WR
CK
VSS
PORTC
To Enhanced CCP
Note 1: PIC16F616/16HV616 only.
D
Q
Q
WR
TRISC
CK
RD
TRISC
RD
PORTC
Note 1:
Port/Peripheral Select signals selects between
PORT data and peripheral output.
TABLE 4-2:
Name
SUMMARY OF REGISTERS ASSOCIATED WITH PORTC
Value on
all other
Resets
Value on
POR, BOR
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ANSEL
ANS7
ANS6
P1M0
C1OUT
C2OUT
—
ANS5
DC1B1
C1OE
C2OE
RC5
ANS4
ANS3
ANS2
ANS1
ANS0
1111 1111 1111 1111
CCP1CON P1M1
CM1CON0 C1ON
CM2CON0 C2ON
DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 0000 0000 0000 0000
C1POL
C2POL
RC4
—
—
C1R
C2R
C1CH1
C2CH1
RC1
C1CH0 0000 -000 0000 -000
C2CH0 0000 -000 0000 -000
PORTC
TRISC
—
—
RC3
RC2
RC0
--xx 00xx --uu 00uu
—
TRISC5 TRISC4 TRISC3
TRISC2
TRISC1
TRISC0 --11 1111 --11 1111
Legend:
x= unknown, u= unchanged, – = unimplemented locations read as ‘0’. Shaded cells are not used by PORTC.
DS41288C-page 42
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
5.1
Timer0 Operation
5.0
TIMER0 MODULE
When used as a timer, the Timer0 module can be used
as either an 8-bit timer or an 8-bit counter.
The Timer0 module is an 8-bit timer/counter with the
following features:
• 8-bit timer/counter register (TMR0)
5.1.1
8-BIT TIMER MODE
• 8-bit prescaler (shared with Watchdog Timer)
• Programmable internal or external clock source
• Programmable external clock edge selection
• Interrupt on overflow
When used as a timer, the Timer0 module will
increment every instruction cycle (without prescaler).
Timer mode is selected by clearing the T0CS bit of the
OPTION register to ‘0’.
Figure 5-1 is a block diagram of the Timer0 module.
When TMR0 is written, the increment is inhibited for
two instruction cycles immediately following the write.
Note:
The value written to the TMR0 register can
be adjusted, in order to account for the two
instruction cycle delay when TMR0 is
written.
5.1.2
8-BIT COUNTER MODE
When used as a counter, the Timer0 module will
increment on every rising or falling edge of the T0CKI
pin. The incrementing edge is determined by the T0SE
bit of the OPTION register. Counter mode is selected by
setting the T0CS bit of the OPTION register to ‘1’.
FIGURE 5-1:
BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER
FOSC/4
Data Bus
0
1
8
1
Sync
TMR0
2 Tcy
T0CKI
pin
0
0
1
Set Flag bit T0IF
on Overflow
T0CS
T0SE
8-bit
Prescaler
PSA
8
PSA
3
1
PS<2:0>
WDT
Time-out
Watchdog
Timer
0
WDTE
PSA
Note 1: T0SE, T0CS, PSA, PS<2:0> are bits in the OPTION register.
2: WDTE bit is in the Configuration Word register.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 43
PIC16F610/616/16HV610/616
When changing the prescaler assignment from the
WDT to the Timer0 module, the following instruction
sequence must be executed (see Example 5-2).
5.1.3
SOFTWARE PROGRAMMABLE
PRESCALER
A single software programmable prescaler is available
for use with either Timer0 or the Watchdog Timer
(WDT), but not both simultaneously. The prescaler
assignment is controlled by the PSA bit of the OPTION
register. To assign the prescaler to Timer0, the PSA bit
must be cleared to a ‘0’.
EXAMPLE 5-2:
CHANGING PRESCALER
(WDT → TIMER0)
CLRWDT
;Clear WDT and
;prescaler
;
BANKSEL OPTION_REG
There are 8 prescaler options for the Timer0 module
ranging from 1:2 to 1:256. The prescale values are
selectable via the PS<2:0> bits of the OPTION register.
In order to have a 1:1 prescaler value for the Timer0
module, the prescaler must be assigned to the WDT
module.
MOVLW
ANDWF
IORLW
MOVWF
b’11110000’ ;Mask TMR0 select and
OPTION_REG,W ;prescaler bits
b’00000011’ ;Set prescale to 1:16
OPTION_REG
;
5.1.4
TIMER0 INTERRUPT
The prescaler is not readable or writable. When
assigned to the Timer0 module, all instructions writing to
the TMR0 register will clear the prescaler.
Timer0 will generate an interrupt when the TMR0
register overflows from FFh to 00h. The T0IF interrupt
flag bit of the INTCON register is set every time the
TMR0 register overflows, regardless of whether or not
the Timer0 interrupt is enabled. The T0IF bit must be
cleared in software. The Timer0 interrupt enable is the
T0IE bit of the INTCON register.
When the prescaler is assigned to WDT, a CLRWDT
instruction will clear the prescaler along with the WDT.
5.1.3.1
Switching Prescaler Between
Timer0 and WDT Modules
Note:
The Timer0 interrupt cannot wake the
processor from Sleep since the timer is
frozen during Sleep.
As a result of having the prescaler assigned to either
Timer0 or the WDT, it is possible to generate an
unintended device Reset when switching prescaler
values. When changing the prescaler assignment from
Timer0 to the WDT module, the instruction sequence
shown in Example 5-1 must be executed.
5.1.5
USING TIMER0 WITH AN
EXTERNAL CLOCK
When Timer0 is in Counter mode, the synchronization
of the T0CKI input and the Timer0 register is
accomplished by sampling the prescaler output on the
Q2 and Q4 cycles of the internal phase clocks.
Therefore, the high and low periods of the external
clock source must meet the timing requirements as
shown in Section 15.0 “Electrical Specifications”.
EXAMPLE 5-1:
CHANGING PRESCALER
(TIMER0 → WDT)
BANKSEL TMR0
CLRWDT
;
;Clear WDT
;Clear TMR0 and
;prescaler
CLRF
TMR0
BANKSEL OPTION_REG
;
BSF
OPTION_REG,PSA ;Select WDT
CLRWDT
;
;
MOVLW b’11111000’
ANDWF OPTION_REG,W
IORLW b’00000101’
MOVWF OPTION_REG
;Mask prescaler
;bits
;Set WDT prescaler
;to 1:32
DS41288C-page 44
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
REGISTER 5-1:
OPTION_REG: OPTION REGISTER
R/W-1
RAPU
R/W-1
R/W-1
T0CS
R/W-1
T0SE
R/W-1
PSA
R/W-1
PS2
R/W-1
PS1
R/W-1
PS0
INTEDG
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2-0
RAPU: PORTA Pull-up Enable bit
1= PORTA pull-ups are disabled
0= PORTA pull-ups are enabled by individual PORT latch values
INTEDG: Interrupt Edge Select bit
1= Interrupt on rising edge of INT pin
0= Interrupt on falling edge of INT pin
T0CS: TMR0 Clock Source Select bit
1= Transition on T0CKI pin
0= Internal instruction cycle clock (FOSC/4)
T0SE: TMR0 Source Edge Select bit
1= Increment on high-to-low transition on T0CKI pin
0= Increment on low-to-high transition on T0CKI pin
PSA: Prescaler Assignment bit
1= Prescaler is assigned to the WDT
0= Prescaler is assigned to the Timer0 module
PS<2:0>: Prescaler Rate Select bits
BIT VALUE TMR0 RATE
WDT RATE
000
001
010
011
100
101
110
111
1 : 2
1 : 4
1 : 1
1 : 2
1 : 8
1 : 4
1 : 16
1 : 32
1 : 64
1 : 128
1 : 256
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
TABLE 5-1:
Name
SUMMARY OF REGISTERS ASSOCIATED WITH TIMER0
Value on
all other
Resets
Value on
POR, BOR
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TMR0
Timer0 Modules Register
GIE PEIE T0IE
xxxx xxxx uuuu uuuu
INTCON
INTE
T0SE
RAIE
PSA
T0IF
PS2
INTF
PS1
RAIF 0000 0000 0000 0000
PS0 1111 1111 1111 1111
OPTION_REG RAPU INTEDG T0CS
TRISA
—
—
TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 --11 1111 --11 1111
Legend: – = Unimplemented locations, read as ‘0’, u= unchanged, x= unknown. Shaded cells are not used by the
Timer0 module.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 45
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 46
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
6.1
Timer1 Operation
6.0
TIMER1 MODULE WITH GATE
CONTROL
The Timer1 module is a 16-bit incrementing counter
which is accessed through the TMR1H:TMR1L register
pair. Writes to TMR1H or TMR1L directly update the
counter.
The Timer1 module is a 16-bit timer/counter with the
following features:
• 16-bit timer/counter register pair (TMR1H:TMR1L)
• Programmable internal or external clock source
• 3-bit prescaler
When used with an internal clock source, the module is
a timer. When used with an external clock source, the
module can be used as either a timer or counter.
• Optional LP oscillator
• Synchronous or asynchronous operation
6.2
Clock Source Selection
• Timer1 gate (count enable) via comparator or
T1G pin
The TMR1CS bit of the T1CON register is used to select
the clock source. When TMR1CS = 0, the clock source
is FOSC/4. When TMR1CS = 1, the clock source is
supplied externally.
• Interrupt on overflow
• Wake-up on overflow (external clock,
Asynchronous mode only)
• Time base for the Capture/Compare function
• Special Event Trigger (with ECCP)
Clock Source
TMR1CS
T1ACS
• Comparator output synchronization to Timer1
clock
FOSC/4
FOSC
0
0
1
0
1
x
Figure 6-1 is a block diagram of the Timer1 module.
T1CKI pin
FIGURE 6-1:
TIMER1 BLOCK DIAGRAM
TMR1GE
T1GINV
TMR1ON
Set flag bit
To C2 Comparator Module
Timer1 Clock
TMR1IF on
Overflow
(2)
TMR1
TMR1H
Synchronized
clock input
0
EN
TMR1L
1
Oscillator
(1)
T1SYNC
OSC1/T1CKI
1
(3)
Synchronize
det
Prescaler
1, 2, 4, 8
0
OSC2/T1G
2
T1CKPS<1:0>
TMR1CS
1
0
INTOSC
Without CLKOUT
FOSC
1
0
C2OUT
T1OSCEN
FOSC/4
Internal
Clock
T1GSS
T1ACS
Note 1: ST Buffer is low power type when using LP osc, or high speed type when using T1CKI.
2: Timer1 register increments on rising edge.
3: Synchronize does not operate while in Sleep.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 47
PIC16F610/616/16HV610/616
6.2.1
INTERNAL CLOCK SOURCE
6.5
Timer1 Operation in
Asynchronous Counter Mode
When the internal clock source is selected the
TMR1H:TMR1L register pair will increment on multiples
of TCY as determined by the Timer1 prescaler.
If control bit T1SYNC of the T1CON register is set, the
external clock input is not synchronized. The timer
continues to increment asynchronous to the internal
phase clocks. The timer will continue to run during
Sleep and can generate an interrupt on overflow,
which will wake-up the processor. However, special
precautions in software are needed to read/write the
timer (see Section 6.5.1 “Reading and Writing
Timer1 in Asynchronous Counter Mode”).
6.2.2
EXTERNAL CLOCK SOURCE
When the external clock source is selected, the Timer1
module may work as a timer or a counter.
When counting, Timer1 is incremented on the rising
edge of the external clock input T1CKI. In addition, the
Counter mode clock can be synchronized to the
microcontroller system clock or run asynchronously.
Note:
When switching from synchronous to
asynchronous operation, it is possible to
skip an increment. When switching from
asynchronous to synchronous operation,
it is possible to produce an additional
increment.
If an external clock oscillator is needed (and the
microcontroller is using the INTOSC without CLKOUT),
Timer1 can use the LP oscillator as a clock source.
Note:
In Counter mode, a falling edge must be
registered by the counter prior to the first
incrementing rising edge.
6.5.1
READING AND WRITING TIMER1 IN
ASYNCHRONOUS COUNTER
MODE
6.3
Timer1 Prescaler
Timer1 has four prescaler options allowing 1, 2, 4 or 8
divisions of the clock input. The T1CKPS bits of the
T1CON register control the prescale counter. The
prescale counter is not directly readable or writable;
however, the prescaler counter is cleared upon a write to
TMR1H or TMR1L.
Reading TMR1H or TMR1L while the timer is running
from an external asynchronous clock will ensure a valid
read (taken care of in hardware). However, the user
should keep in mind that reading the 16-bit timer in two
8-bit values itself, poses certain problems, since the
timer may overflow between the reads.
For writes, it is recommended that the user simply stop
the timer and write the desired values. A write
contention may occur by writing to the timer registers,
while the register is incrementing. This may produce an
unpredictable value in the TMR1H:TMR1L register pair.
6.4
Timer1 Oscillator
A low-power 32.768 kHz crystal oscillator is built-in
between pins OSC1 (input) and OSC2 (output). The
oscillator is enabled by setting the T1OSCEN control
bit of the T1CON register. The oscillator will continue to
run during Sleep.
6.6
Timer1 Gate
The Timer1 oscillator is shared with the system LP
oscillator. Thus, Timer1 can use this mode only when
the primary system clock is derived from the internal
oscillator or when the oscillator is in the LP Oscillator
mode. The user must provide a software time delay to
ensure proper oscillator start-up.
Timer1 gate source is software configurable to be the
T1G pin or the output of Comparator C2. This allows the
device to directly time external events using T1G or
analog events using Comparator C2. See the
CM2CON1 register (Register 8-3) for selecting the
Timer1 gate source. This feature can simplify the
software for a Delta-Sigma A/D converter and many
other applications. For more information on Delta-Sigma
A/D converters, see the Microchip web site
(www.microchip.com).
TRISA5 and TRISA4 bits are set when the Timer1
oscillator is enabled. RA5 and RA4 bits read as ‘0’ and
TRISA5 and TRISA4 bits read as ‘1’.
Note:
The oscillator requires a start-up and
stabilization time before use. Thus,
T1OSCEN should be set and a suitable
delay observed prior to enabling Timer1.
Note:
TMR1GE bit of the T1CON register must
be set to use either T1G or C2OUT as the
Timer1 gate source. See the CM2CON1
register (Register 8-3) for more informa-
tion on selecting the Timer1 gate source.
Timer1 gate can be inverted using the T1GINV bit of
the T1CON register, whether it originates from the T1G
pin or Comparator C2 output. This configures Timer1 to
measure either the active-high or active-low time
between events.
DS41288C-page 48
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
In Capture mode, the value in the TMR1H:TMR1L
register pair is copied into the CCPR1H:CCPR1L
register pair on a configured event.
6.7
Timer1 Interrupt
The Timer1 register pair (TMR1H:TMR1L) increments
to FFFFh and rolls over to 0000h. When Timer1 rolls
over, the Timer1 interrupt flag bit of the PIR1 register is
set. To enable the interrupt on rollover, you must set
these bits:
In Compare mode, an event is triggered when the value
CCPR1H:CCPR1L register pair matches the value in
the TMR1H:TMR1L register pair. This event can be a
Special Event Trigger.
• TMR1IE bit of the PIE1 register
For more information, see Section 10.0 “Enhanced
Capture/Compare/PWM (With Auto-Shutdown and
Dead Band) Module (PIC16F616/16HV616 Only)”.
• PEIE bit of the INTCON register
• GIE bit of the INTCON register
• T1SYNC bit of the T1CON register
• TMR1CS bit of the T1CON register
• T1OSCEN bit of the T1CON register (can be set)
6.10 ECCP Special Event Trigger
(PIC16F616/16HV616 Only)
The interrupt is cleared by clearing the TMR1IF bit in
the Interrupt Service Routine.
When the ECCP is configured to trigger a special
event, the trigger will clear the TMR1H:TMR1L register
pair. This special event does not cause a Timer1 inter-
rupt. The ECCP module may still be configured to gen-
erate a ECCP interrupt.
Note:
The TMR1H:TTMR1L register pair and the
TMR1IF bit should be cleared before
enabling interrupts.
In this mode of operation, the CCPR1H:CCPR1L register
pair effectively becomes the period register for Timer1.
6.8
Timer1 Operation During Sleep
Timer1 should be synchronized to the FOSC to utilize the
Special Event Trigger. Asynchronous operation of
Timer1 can cause a Special Event Trigger to be missed.
Timer1 can only operate during Sleep when setup in
Asynchronous Counter mode. In this mode, an external
crystal or clock source can be used to increment the
counter. To set up the timer to wake the device:
In the event that a write to TMR1H or TMR1L coincides
with a Special Event Trigger from the ECCP, the write
will take precedence.
• TMR1ON bit of the T1CON register must be set
• TMR1IE bit of the PIE1 register must be set
• PEIE bit of the INTCON register must be set
For more information, see Section 10.2.4 “Special
Event Trigger”.
The device will wake-up on an overflow and execute
the next instruction. If the GIE bit of the INTCON
register is set, the device will call the Interrupt Service
Routine (0004h).
6.11 Comparator Synchronization
The same clock used to increment Timer1 can also be
used to synchronize the comparator output. This
feature is enabled in the Comparator module.
6.9
ECCP Capture/Compare Time Base
(PIC16F616/16HV616 Only)
When using the comparator for Timer1 gate, the
comparator output should be synchronized to Timer1.
This ensures Timer1 does not miss an increment if the
comparator changes.
The ECCP module uses the TMR1H:TMR1L register
pair as the time base when operating in Capture or
Compare mode.
For
more
information,
see
Section 8.8.2
“Synchronizing Comparator C2 Output to Timer1”.
FIGURE 6-2:
TIMER1 INCREMENTING EDGE
T1CKI = 1
when TMR1
Enabled
T1CKI = 0
when TMR1
Enabled
Note 1: Arrows indicate counter increments.
2: In Counter mode, a falling edge must be registered by the counter prior to the first incrementing rising edge of the clock.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 49
PIC16F610/616/16HV610/616
6.12 Timer1 Control Register
The Timer1 Control register (T1CON), shown in
Register 6-1, is used to control Timer1 and select the
various features of the Timer1 module.
REGISTER 6-1:
T1CON: TIMER1 CONTROL REGISTER
R/W-0
T1GINV(1)
R/W-0
TMR1GE(2)
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
T1CKPS1
T1CKPS0
T1OSCEN
T1SYNC
TMR1CS
TMR1ON
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
bit 6
T1GINV: Timer1 Gate Invert bit(1)
1= Timer1 gate is active-high (Timer1 counts when gate is high)
0= Timer1 gate is active-low (Timer1 counts when gate is low)
TMR1GE: Timer1 Gate Enable bit(2)
If TMR1ON = 0:
This bit is ignored
If TMR1ON = 1:
1= Timer1 counting is controlled by the Timer1 Gate function
0= Timer1 is always counting
bit 5-4
bit 3
T1CKPS<1:0>: Timer1 Input Clock Prescale Select bits
11= 1:8 Prescale Value
10= 1:4 Prescale Value
01= 1:2 Prescale Value
00= 1:1 Prescale Value
T1OSCEN: LP Oscillator Enable Control bit
If INTOSC without CLKOUT oscillator is active:
1= LP oscillator is enabled for Timer1 clock
0= LP oscillator is off
Else:
This bit is ignored
bit 2
bit 1
T1SYNC: Timer1 External Clock Input Synchronization Control bit
TMR1CS = 1:
1= Do not synchronize external clock input
0= Synchronize external clock input
TMR1CS = 0:
This bit is ignored. Timer1 uses the internal clock
TMR1CS: Timer1 Clock Source Select bit
1= External clock from T1CKI pin (on the rising edge)
0= Internal clock
If TMR1ACS = 0:
FOSC/4
If TMR1ACS = 1:
FOSC
bit 0
TMR1ON: Timer1 On bit
1= Enables Timer1
0= Stops Timer1
Note 1: T1GINV bit inverts the Timer1 gate logic, regardless of source.
2: TMR1GE bit must be set to use either T1G pin or C2OUT, as selected by the T1GSS bit of the CM2CON1
register, as a Timer1 gate source.
DS41288C-page 50
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 6-1:
SUMMARY OF REGISTERS ASSOCIATED WITH TIMER1
Value on
all other
Resets
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CM2CON0
C2ON
C2OUT
MC2OUT
PEIE
ADIE(1)
ADIF(1)
C2OE
—
C2POL
T1ACS
INTE
—
C2R
C2HYS
T0IF
—
C2CH1
T1GSS
C2CH0
C2SYNC
RAIF
0000 -000
00-0 0010
0000 0000
-000 0-00
-000 0-00
xxxx xxxx
xxxx xxxx
0000 -000
00-0 0010
0000 0000
-000 0-00
-000 0-00
uuuu uuuu
uuuu uuuu
CM2CON1
INTCON
PIE1
MC1OUT
C1HYS
RAIE
C1IE
GIE
—
T0IE
INTF
CCP1IE(1)
CCP1IF(1)
C2IE
TMR2IE(1)
TMR2IF(1)
TMR1IE
TMR1IF
PIR1
—
C2IF
C1IF
—
TMR1H
TMR1L
Holding Register for the Most Significant Byte of the 16-bit TMR1 Register
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register
T1CON
T1GINV
TMR1GE T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
TMR1CS
TMR1ON
0000 0000
uuuu uuuu
Legend:
x= unknown, u= unchanged, – =unimplemented, read as ‘0’. Shaded cells are not used by the Timer1 module.
Note 1:
PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 51
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 52
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
The TMR2 and PR2 registers are both fully readable
and writable. On any Reset, the TMR2 register is set to
00h and the PR2 register is set to FFh.
7.0
TIMER2 MODULE
(PIC16F616/16HV616 ONLY)
The Timer2 module is an 8-bit timer with the following
features:
Timer2 is turned on by setting the TMR2ON bit in the
T2CON register to a ‘1’. Timer2 is turned off by setting
the TMR2ON bit to a ‘0’.
• 8-bit timer register (TMR2)
• 8-bit period register (PR2)
The Timer2 prescaler is controlled by the T2CKPS bits
in the T2CON register. The Timer2 postscaler is
controlled by the TOUTPS bits in the T2CON register.
The prescaler and postscaler counters are cleared
when:
• Interrupt on TMR2 match with PR2
• Software programmable prescaler (1:1, 1:4, 1:16)
• Software programmable postscaler (1:1 to 1:16)
See Figure 7-1 for a block diagram of Timer2.
• A write to TMR2 occurs.
• A write to T2CON occurs.
7.1
Timer2 Operation
• Any device Reset occurs (Power-on Reset, MCLR
Reset, Watchdog Timer Reset, or Brown-out
Reset).
The clock input to the Timer2 module is the system
instruction clock (FOSC/4). The clock is fed into the
Timer2 prescaler, which has prescale options of 1:1,
1:4 or 1:16. The output of the prescaler is then used to
increment the TMR2 register.
Note:
TMR2 is not cleared when T2CON is
written.
The values of TMR2 and PR2 are constantly compared
to determine when they match. TMR2 will increment
from 00h until it matches the value in PR2. When a
match occurs, two things happen:
• TMR2 is reset to 00h on the next increment cycle.
• The Timer2 postscaler is incremented
The match output of the Timer2/PR2 comparator is
then fed into the Timer2 postscaler. The postscaler has
postscale options of 1:1 to 1:16 inclusive. The output of
the Timer2 postscaler is used to set the TMR2IF
interrupt flag bit in the PIR1 register.
FIGURE 7-1:
TIMER2 BLOCK DIAGRAM
Sets Flag
bit TMR2IF
Output
TMR2
Prescaler
Reset
EQ
TMR2
FOSC/4
1:1, 1:4, 1:16
Postscaler
1:1 to 1:16
2
Comparator
PR2
T2CKPS<1:0>
4
TOUTPS<3:0>
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 53
PIC16F610/616/16HV610/616
REGISTER 7-1:
T2CON: TIMER2 CONTROL REGISTER
U-0
—
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
TOUTPS3
TOUTPS2
TOUTPS1
TOUTPS0
TMR2ON
T2CKPS1
T2CKPS0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 7
Unimplemented: Read as ‘0’
bit 6-3
TOUTPS<3:0>: Timer2 Output Postscaler Select bits
0000= 1:1 Postscaler
0001= 1:2 Postscaler
0010= 1:3 Postscaler
0011= 1:4 Postscaler
0100= 1:5 Postscaler
0101= 1:6 Postscaler
0110= 1:7 Postscaler
0111= 1:8 Postscaler
1000= 1:9 Postscaler
1001= 1:10 Postscaler
1010= 1:11 Postscaler
1011= 1:12 Postscaler
1100= 1:13 Postscaler
1101= 1:14 Postscaler
1110= 1:15 Postscaler
1111= 1:16 Postscaler
bit 2
TMR2ON: Timer2 On bit
1= Timer2 is on
0= Timer2 is off
bit 1-0
T2CKPS<1:0>: Timer2 Clock Prescale Select bits
00= Prescaler is 1
01= Prescaler is 4
1x= Prescaler is 16
TABLE 7-1:
SUMMARY OF ASSOCIATED TIMER2 REGISTERS
Value on
all other
Resets
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INTCON
PIE1
GIE
—
PEIE
T0IE
CCP1IE
CCP1IF
INTE
C2IE
C2IF
RAIE
C1IE
C1IF
T0IF
—
INTF
TMR2IE
TMR2IF
RAIF
0000 0000
0000 0000
-000 0-00
-000 0-00
1111 1111
0000 0000
-000 0000
(1)
(1)
(1)
(1)
(1)
ADIE
ADIF
TMR1IE -000 0-00
TMR1IF -000 0-00
1111 1111
(1)
PIR1
—
—
PR2
Timer2 Module Period Register
Holding Register for the 8-bit TMR2 Register
TMR2
T2CON
0000 0000
—
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000
Legend:
Note 1:
x= unknown, u= unchanged, – =unimplemented read as ‘0’. Shaded cells are not used for Timer2 module.
PIC16F616/16HV616 only.
DS41288C-page 54
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
FIGURE 8-1:
SINGLE COMPARATOR
8.0
COMPARATOR MODULE
Comparators are used to interface analog circuits to a
digital circuit by comparing two analog voltages and
providing a digital indication of their relative magnitudes.
The comparators are very useful mixed signal building
blocks because they provide analog functionality
independent of the device. The Analog Comparator
module includes the following features:
VIN+
VIN-
+
Output
–
VIN-
VIN+
• Independent comparator control
• Programmable input selection
• Comparator output is available internally/externally
• Programmable output polarity
• Interrupt-on-change
Output
• Wake-up from Sleep
• PWM shutdown
• Timer1 gate (count enable)
• Output synchronization to Timer1 clock input
• SR Latch
Note:
The black areas of the output of the
comparator represents the uncertainty
due to input offsets and response time.
• Programmable and fixed voltage reference
• User-enable Comparator Hysteresis
Note:
Only Comparator C2 can be linked to
Timer1.
8.1
Comparator Overview
A single comparator is shown in Figure 8-1 along with
the relationship between the analog input levels and
the digital output. When the analog voltage at VIN+ is
less than the analog voltage at VIN-, the output of the
comparator is a digital low level. When the analog
voltage at VIN+ is greater than the analog voltage at
VIN-, the output of the comparator is a digital high level.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 55
PIC16F610/616/16HV610/616
FIGURE 8-2:
COMPARATOR C1 SIMPLIFIED BLOCK DIAGRAM
C1CH<1:0>
C1POL
2
To
Data Bus
D
Q
Q1
C12IN0-
EN
0
RD_CM1CON0
Set C1IF
C12IN1-
C12IN2-
C12IN3-
1
MUX
2
D
Q
Q3*RD_CM1CON0
Reset
EN
To PWM Logic
C1OE
3
CL
(1)
C1ON
C1
C1R
C1VIN-
C1VIN+
-
C1IN+
0
MUX
1
C1OUT
+
(2)
C1VREF
C1OUT pin
C1POL
Note 1: When C1ON = 0, the C1 comparator will produce a ‘0’ output to the XOR Gate.
2: Output shown for reference only. See I/O port pin block diagram for more detail.
FIGURE 8-3:
COMPARATOR C2 SIMPLIFIED BLOCK DIAGRAM
C2POL
To
D
Q
Data Bus
Q1
EN
RD_CM2CON0
C2CH<1:0>
Set C2IF
2
D
Q
Q3*RD_CM2CON0
EN
(1)
C2ON
C2
C12IN0-
0
CL
Reset
C12IN1-
C2IN2-
C2IN3-
1
MUX
2
C2VIN-
C2VIN+
To other peripherals
C2OE
C2OUT
3
C2SYNC
C2POL
0
C2R
MUX
(2)
D
Q
1
C2OUT pin
C2IN+
0
MUX
1
From Timer1
Clock
SYNCC2OUT
To Timer1 Gate
To SR Latch
C2VREF
Note 1: When C2ON = 0, the C2 comparator will produce a ‘0’ output to the XOR Gate.
2: Output shown for reference only. See I/O port pin block diagram for more detail.
DS41288C-page 56
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
8.2.4
COMPARATOR OUTPUT SELECTION
8.2
Comparator Control
The output of the comparator can be monitored by
reading either the CxOUT bit of the CMxCON0 register
or the MCxOUT bit of the CM2CON1 register. In order
to make the output available for an external connection,
the following conditions must be true:
Each comparator has
Configuration register: CM1CON0 for Comparator C1
and CM2CON0 for Comparator C2. In addition,
Comparator C2 has
CM2CON1, for controlling the interaction with Timer1 and
simultaneous reading of both comparator outputs.
a
separate control and
a
second control register,
• CxOE bit of the CMxCON0 register must be set
• Corresponding TRIS bit must be cleared
The CM1CON0 and CM2CON0 registers (see Registers
8-1 and 8-2, respectively) contain the control and Status
bits for the following:
• CxON bit of the CMxCON0 register must be set.
Note 1: The CxOE bit overrides the PORT data
latch. Setting the CxON has no impact on
the port override.
• Enable
• Input selection
• Reference selection
• Output selection
• Output polarity
2: The internal output of the comparator is
latched with each instruction cycle.
Unless otherwise specified, external
outputs are not latched.
8.2.1
COMPARATOR ENABLE
8.2.5
COMPARATOR OUTPUT POLARITY
Setting the CxON bit of the CMxCON0 register enables
the comparator for operation. Clearing the CxON bit
disables the comparator for minimum current
consumption.
Inverting the output of the comparator is functionally
equivalent to swapping the comparator inputs. The
polarity of the comparator output can be inverted by
setting the CxPOL bit of the CMxCON0 register.
Clearing the CxPOL bit results in a non-inverted output.
8.2.2
COMPARATOR INPUT SELECTION
Table 8-1 shows the output state versus input
conditions, including polarity control.
The CxCH<1:0> bits of the CMxCON0 register direct
one of four analog input pins to the comparator
inverting input.
TABLE 8-1:
COMPARATOR OUTPUT
STATE VS. INPUT
CONDITIONS
Note:
To use CxIN+ and CxIN- pins as analog
inputs, the appropriate bits must be set in
the ANSEL register and the corresponding
TRIS bits must also be set to disable the
output drivers.
Input Condition
CxPOL
CxOUT
CxVIN- > CxVIN+
CxVIN- < CxVIN+
CxVIN- > CxVIN+
CxVIN- < CxVIN+
0
0
1
1
0
1
1
0
8.2.3
COMPARATOR REFERENCE
SELECTION
Setting the CxR bit of the CMxCON0 register directs an
internal voltage reference or an analog input pin to the
non-inverting input of the comparator. See Section 8.11
“Comparator Voltage Reference” for more information
on the internal voltage reference module.
8.3
Comparator Response Time
The comparator output is indeterminate for a period of
time after the change of an input source or the selection
of a new reference voltage. This period is referred to as
the response time. The response time of the
comparator differs from the settling time of the voltage
reference. Therefore, both of these times must be
considered when determining the total response time
to a comparator input change. See the Comparator and
Voltage Reference Specifications in Section 15.0
“Electrical Specifications” for more details.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 57
PIC16F610/616/16HV610/616
FIGURE 8-4:
COMPARATOR
8.4
Comparator Interrupt Operation
INTERRUPT TIMING W/O
CMxCON0 READ
The comparator interrupt flag can be set whenever
there is a change in the output value of the comparator.
Changes are recognized by means of a mismatch
circuit which consists of two latches and an
exclusive-or gate (see Figure 8-2 and Figure 8-3). One
latch is updated with the comparator output level when
the CMxCON0 register is read. This latch retains the
value until the next read of the CMxCON0 register or
the occurrence of a Reset. The other latch of the
mismatch circuit is updated on every Q1 system clock.
A mismatch condition will occur when a comparator
output change is clocked through the second latch on
the Q1 clock cycle. At this point the two mismatch
latches have opposite output levels which is detected
by the exclusive-or gate and fed to the interrupt
circuitry. The mismatch condition persists until either
the CMxCON0 register is read or the comparator
output returns to the previous state.
Q1
Q3
CxIN+
TRT
CxOUT
Set CxIF (edge)
CxIF
reset by software
FIGURE 8-5:
COMPARATOR
INTERRUPT TIMING WITH
CMxCON0 READ
Q1
Q3
CxIN+
TRT
Note 1: A write operation to the CMxCON0
register will also clear the mismatch
condition because all writes include a read
operation at the beginning of the write
cycle.
CxOUT
Set CxIF (edge)
CxIF
cleared by CMxCON0 read
reset by software
2: Comparator interrupts will operate correctly
regardless of the state of CxOE.
The comparator interrupt is set by the mismatch edge
and not the mismatch level. This means that the inter-
rupt flag can be reset without the additional step of
reading or writing the CMxCON0 register to clear the
mismatch registers. When the mismatch registers are
cleared, an interrupt will occur upon the comparator’s
return to the previous state, otherwise no interrupt will
be generated.
Note 1: If a change in the CMxCON0 register
(CxOUT) should occur when a read oper-
ation is being executed (start of the Q2
cycle), then the CxIF of the PIR1 register
interrupt flag may not get set.
2: When either comparator is first enabled,
bias circuitry in the comparator module
may cause an invalid output from the
comparator until the bias circuitry is stable.
Allow about 1 μs for bias settling then clear
the mismatch condition and interrupt flags
before enabling comparator interrupts.
Software will need to maintain information about the
status of the comparator output, as read from the
CMxCON0 register, or CM2CON1 register, to determine
the actual change that has occurred.
The CxIF bit of the PIR1 register is the comparator
interrupt flag. This bit must be reset in software by
clearing it to ‘0’. Since it is also possible to write a ‘1’ to
this register, an interrupt can be generated.
The CxIE bit of the PIE1 register and the PEIE and GIE
bits of the INTCON register must all be set to enable
comparator interrupts. If any of these bits are cleared,
the interrupt is not enabled, although the CxIF bit of the
PIR1 register will still be set if an interrupt condition
occurs.
DS41288C-page 58
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
8.5
Operation During Sleep
The comparator, if enabled before entering Sleep mode,
remains active during Sleep. The additional current
consumed by the comparator is shown separately in
Section 15.0 “Electrical Specifications”. If the
comparator is not used to wake the device, power
consumption can be minimized while in Sleep mode by
turning off the comparator. Each comparator is turned off
by clearing the CxON bit of the CMxCON0 register.
A change to the comparator output can wake-up the
device from Sleep. To enable the comparator to wake
the device from Sleep, the CxIE bit of the PIE1 register
and the PEIE bit of the INTCON register must be set.
The instruction following the Sleep instruction always
executes following a wake from Sleep. If the GIE bit of
the INTCON register is also set, the device will then
execute the interrupt service routine.
8.6
Effects of a Reset
A device Reset forces the CMxCON0 and CM2CON1
registers to their Reset states. This forces both
comparators and the voltage references to their OFF
states.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 59
PIC16F610/616/16HV610/616
REGISTER 8-1:
CM1CON0: COMPARATOR 1 CONTROL REGISTER 0
R/W-0
C1ON
R-0
R/W-0
C1OE
R/W-0
U-0
—
R/W-0
C1R
R/W-0
R/W-0
C1OUT
C1POL
C1CH1
C1CH0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
bit 6
C1ON: Comparator C1 Enable bit
1= Comparator C1 is enabled
0= Comparator C1 is disabled
C1OUT: Comparator C1 Output bit
If C1POL = 1(inverted polarity):
C1OUT = 0when C1VIN+ > C1VIN-
C1OUT = 1when C1VIN+ < C1VIN-
If C1POL = 0(non-inverted polarity):
C1OUT = 1when C1VIN+ > C1VIN-
C1OUT = 0when C1VIN+ < C1VIN-
bit 5
bit 4
C1OE: Comparator C1 Output Enable bit
1= C1OUT is present on the C1OUT pin(1)
0= C1OUT is internal only
C1POL: Comparator C1 Output Polarity Select bit
1= C1OUT logic is inverted
0= C1OUT logic is not inverted
bit 3
bit 2
Unimplemented: Read as ‘0’
C1R: Comparator C1 Reference Select bit (non-inverting input)
1= C1VIN+ connects to C1VREF output
0= C1VIN+ connects to C1IN+ pin
bit 1-0
C1CH<1:0>: Comparator C1 Channel Select bit
00= C12IN0- pin of C1 connects to C1VIN-
01= C12IN1- pin of C1 connects to C1VIN-
10= C12IN2- pin of C1 connects to C1VIN-
11= C12IN3- pin of C1 connects to C1VIN-
Note 1: Comparator output requires the following three conditions: C1OE = 1, C1ON = 1and corresponding port
TRIS bit = 0.
DS41288C-page 60
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
REGISTER 8-2:
CM2CON0: COMPARATOR 2 CONTROL REGISTER 0
R/W-0
C2ON
R-0
R/W-0
C2OE
R/W-0
U-0
—
R/W-0
C2R
R/W-0
R/W-0
C2OUT
C2POL
C2CH1
C2CH0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
bit 6
C2ON: Comparator C2 Enable bit
1= Comparator C2 is enabled
0= Comparator C2 is disabled
C2OUT: Comparator C2 Output bit
If C2POL = 1(inverted polarity):
C2OUT = 0when C2VIN+ > C2VIN-
C2OUT = 1when C2VIN+ < C2VIN-
If C2POL = 0(non-inverted polarity):
C2OUT = 1when C2VIN+ > C2VIN-
C2OUT = 0when C2VIN+ < C2VIN-
bit 5
bit 4
C2OE: Comparator C2 Output Enable bit
1= C2OUT is present on C2OUT pin(1)
0= C2OUT is internal only
C2POL: Comparator C2 Output Polarity Select bit
1= C2OUT logic is inverted
0= C2OUT logic is not inverted
bit 3
bit 2
Unimplemented: Read as ‘0’
C2R: Comparator C2 Reference Select bits (non-inverting input)
1= C2VIN+ connects to C2VREF
0= C2VIN+ connects to C2IN+ pin
bit 1-0
C2CH<1:0>: Comparator C2 Channel Select bits
00= C2VIN- pin of C2 connects to C12IN0-
01= C2VIN- pin of C2 connects to C12IN1-
10= C2VIN- pin of C2 connects to C12IN2-
11= C2VIN- pin of C2 connects to C12IN3-
Note 1: Comparator output requires the following three conditions: C2OE = 1, C2ON = 1and corresponding port
TRIS bit = 0.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 61
PIC16F610/616/16HV610/616
8.7
Comparator Analog Input
Connection Considerations
Note 1: When reading a PORT register, all pins
configured as analog inputs will read as a
‘0’. Pins configured as digital inputs will
convert as an analog input, according to
the input specification.
A simplified circuit for an analog input is shown in
Figure 8-6. Since the analog input pins share their con-
nection with a digital input, they have reverse biased
ESD protection diodes to VDD and VSS. The analog
input, therefore, must be between VSS and VDD. If the
input voltage deviates from this range by more than
0.6V in either direction, one of the diodes is forward
biased and a latch-up may occur.
2: Analog levels on any pin defined as a
digital input, may cause the input buffer to
consume more current than is specified.
A maximum source impedance of 10 kΩ is recommended
for the analog sources. Also, any external component
connected to an analog input pin, such as a capacitor or
a Zener diode, should have very little leakage current to
minimize inaccuracies introduced.
FIGURE 8-6:
ANALOG INPUT MODEL
VDD
VT ≈ 0.6V
RIC
Rs < 10K
To ADC Input
AIN
ILEAKAGE
±500 nA
CPIN
5 pF
VA
VT ≈ 0.6V
Vss
Legend: CPIN
= Input Capacitance
ILEAKAGE = Leakage Current at the pin due to various junctions
RIC
RS
VA
= Interconnect Resistance
= Source Impedance
= Analog Voltage
VT
= Threshold Voltage
DS41288C-page 62
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
8.8.2
SYNCHRONIZING COMPARATOR
C2 OUTPUT TO TIMER1
8.8
Additional Comparator Features
There are three additional comparator features:
The Comparator C2 output can be synchronized with
Timer1 by setting the C2SYNC bit of the CM2CON1
register. When enabled, the C2 output is latched on the
falling edge of the Timer1 clock source. If a prescaler is
used with Timer1, the comparator output is latched after
the prescaling function. To prevent a race condition, the
comparator output is latched on the falling edge of the
Timer1 clock source and Timer1 increments on the
rising edge of its clock source. See the Comparator
Block Diagram (Figure 8-3) and the Timer1 Block
Diagram (Figure 6-1) for more information.
• Timer1 count enable (gate)
• Synchronizing output with Timer1
• Simultaneous read of comparator outputs
8.8.1
COMPARATOR C2 GATING TIMER1
This feature can be used to time the duration or interval
of analog events. Clearing the T1GSS bit of the
CM2CON1 register will enable Timer1 to increment
based on the output of Comparator C2. This requires
that Timer1 is on and gating is enabled. See
Section 6.0 “Timer1 Module with Gate Control” for
details.
8.8.3
SIMULTANEOUS COMPARATOR
OUTPUT READ
It is recommended to synchronize the comparator with
Timer1 by setting the C2SYNC bit when the comparator
is used as the Timer1 gate source. This ensures Timer1
does not miss an increment if the comparator changes
during an increment.
The MC1OUT and MC2OUT bits of the CM2CON1
register are mirror copies of both comparator outputs.
The ability to read both outputs simultaneously from a
single register eliminates the timing skew of reading
separate registers.
Note 1: Obtaining the status of C1OUT or C2OUT
by reading CM2CON1 does not affect the
comparator interrupt mismatch registers.
REGISTER 8-3:
CM2CON1: COMPARATOR 2 CONTROL REGISTER 1
R-0
MC1OUT
bit 7
R-0
U-0
—
R/W-0
R/W-0
R/W-0
R/W-1
R/W-0
MC2OUT
T1ACS
C1HYS
C2HYS
T1GSS
C2SYNC
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
bit 6
bit 5
bit 4
MC1OUT: Mirror Copy of C1OUT bit
MC2OUT: Mirror Copy of C2OUT bit
Unimplemented: Read as ‘0’
T1ACS: Timer1 Alternate Clock Select bit
1= Timer1 clock source is the system clock (FOSC)
0= Timer1 clock source is the internal clock FOSC/4)
bit 3
bit 2
bit 1
bit 0
C1HYS: Comparator C1 Hysteresis Enable bit
1= Comparator C1 Hysteresis enabled
0= Comparator C1 Hysteresis disabled
C2HYS: Comparator C2 Hysteresis Enable bit
1= Comparator C2 Hysteresis enabled
0= Comparator C2 Hysteresis disabled
T1GSS: Timer1 Gate Source Select bit
1= Timer1 gate source is T1G
0= Timer1 gate source is SYNCC2OUT.
C2SYNC: Comparator C2 Output Synchronization bit
1= C2 Output is synchronous to falling edge of Timer1 clock
0= C2 Output is asynchronous
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 63
PIC16F610/616/16HV610/616
Figure 8-9 shows the relationship between the analog
input levels and digital output of a comparator with and
without hysteresis. The output of the comparator
changes from a low state to a high state only when the
analog voltage at VIN+ rises above the upper hysteresis
threshold (VH+). The output of the comparator changes
from a high state to a low state only when the analog
voltage at VIN+ falls below the lower hysteresis
threshold (VH-).
8.9
Comparator Hysteresis
Each comparator has built-in hysteresis that is user
enabled by setting the C1HYS or C2HYS bits of the
CM2CON1 register. The hysteresis feature can help
filter noise and reduce multiple comparator output
transitions when the output is changing state.
FIGURE 8-7:
COMPARATOR HYSTERESIS
VIN+
VIN-
+
–
Output
V+
VH+
VIN-
VH-
VIN+
Output
(Without Hysteresis)
Output
(With Hysteresis)
Note:
The black areas of the comparator output represents the uncertainty due to input offsets and response time.
DS41288C-page 64
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 8-2:
SUMMARY OF REGISTERS ASSOCIATED WITH THE COMPARATOR AND VOLTAGE
REFERENCE MODULES
Value on
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
all other
Resets
ANSEL
ANS7
C1ON
C2ON
MC1OUT
GIE
ANS6
C1OUT
C2OUT
MC2OUT
PEIE
ADIE(1)
ADIF(1)
—
ANS5
C1OE
C2OE
—
ANS4
C1POL
C2POL
T1ACS
INTE
ANS3
C1SP
C2SP
C1HYS
RAIE
C1IE
ANS2
C1R
ANS1
C1CH1
C2CH1
T1GSS
INTF
TMR2IE(1)
TMR2IF(1)
RA1
ANS0
C1CH0
C2CH0
C2SYNC
RAIF
1111 1111
0000 0000
0000 0000
00-0 0010
0000 000x
-000 0-00
-000 0-00
--x0 x000
--xx 00xx
0000 00-0
00-- ----
--11 1111
1111 1111
0000 0000
1111 1111
0000 0000
0000 0000
00-0 0010
0000 000x
-000 0-00
-000 0-00
--x0 x000
--uu 00uu
0000 00-0
00-- ----
--11 1111
1111 1111
0000 0000
CM1CON0
CM2CON0
CM2CON1
INTCON
PIE1
C2R
C2HYS
T0IF
—
T0IE
—
CCP1IE(1)
CCP1IF(1)
RA5
C2IE
TMR1IE
TMR1IF
RA0
PIR1
—
C2IF
C1IF
—
PORTA
PORTC
SRCON0
SRCON1
TRISA
—
RA4
RA3
RA2
—
—
RC5
RC4
RC3
RC2
RC1
RC0
SR1
SRCS1
—
SR0
C1SEN
—
C2REN
—
PULSS
—
PULSR
—
—
SRCLKEN
—
SRCS0
—
—
TRISA5
TRISC5
VRR
TRISA4
TRISC4
FVREN
TRISA3
TRISC3
VR3
TRISA2
TRISC2
VR2
TRISA1
TRISC1
VR1
TRISA0
TRISC0
VR0
TRISC
VRCON
C1VREN
C2VREN
Legend:
x= unknown, u= unchanged, – = unimplemented, read as ‘0’. Shaded cells are not used for comparator.
Note 1:
PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 65
PIC16F610/616/16HV610/616
inputs are high the latch will go to the Reset state. Both
8.10 Comparator SR Latch
the PULSS and PULSR bits are self resetting which
means that a single write to either of the bits is all that is
necessary to complete a latch Set or Reset operation.
The SR latch module provides additional control of the
comparator outputs. The module consists of a single
SR latch and output multiplexers. The SR latch can be
set, reset or toggled by the comparator outputs. The SR
latch may also be set or reset, independent of
comparator output, by control bits in the SRCON0
control register. The SR latch output multiplexers select
whether the latch outputs or the comparator outputs are
directed to the I/O port logic for eventual output to a pin.
8.10.2
LATCH OUTPUT
The SR<1:0> bits of the SRCON0 register control the
latch output multiplexers and determine four possible
output configurations. In these four configurations, the
CxOUT I/O port logic is connected to:
• C1OUT and C2OUT
• C1OUT and SR latch Q
• C2OUT and SR latch Q
• SR latch Q and Q
The SR latch also has a variable clock, which is con-
nected to the set input of the latch. The SRCLKEN bit
of SRCON0 enables the SR latch set clock. The clock
will periodically pulse the set input of the latch. Control
over the frequency of the SR latch set clock is provided
by the SRCS<1:0> bits of SRCON1 register.
After any Reset, the default output configuration is the
unlatched C1OUT and C2OUT mode. This maintains
compatibility with devices that do not have the SR latch
feature.
8.10.1
LATCH OPERATION
The latch is a Set-Reset latch that does not depend on a
clock source. Each of the Set and Reset inputs are
active-high. Each latch input is connected to a
comparator output and a software controlled pulse
generator. The latch can be set by C1OUT or the PULSS
bit of the SRCON0 register. The latch can be reset by
C2OUT or the PULSR bit of the SRCON0 register. The
latch is reset-dominant, therefore, if both Set and Reset
The applicable TRIS bits of the corresponding ports
must be cleared to enable the port pin output drivers.
Additionally, the CxOE comparator output enable bits of
the CMxCON0 registers must be set in order to make the
comparator or latch outputs available on the output pins.
The latch configuration enable states are completely
independent of the enable states for the comparators.
FIGURE 8-8:
SR LATCH SIMPLIFIED BLOCK DIAGRAM
SRCLKEN
SRCLK
SR0
C1OE
PULSS
Pulse
Gen(2)
0
MUX
1
C1OUT (from comparator)
C1SEN
S
Q
(3)
C1OUT pin
SR
Latch
(1)
C2OE
SYNCC2OUT (from comparator)
C2REN
1
MUX
R
Q
(3)
0
C2OUT pin
PULSR
Pulse
SR1
Gen(2)
Note 1: If R = 1and S = 1simultaneously, Q = 0, Q = 1
2: Pulse generator causes a 1 TOSC pulse width.
3: Output shown for reference only. See I/O port pin block diagram for more detail.
DS41288C-page 66
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
REGISTER 8-4:
SRCON0: SR LATCH CONTROL 0 REGISTER
R/W-0
R/W-0
R/W-0
R/W-0
R/S-0
R/S-0
U-0
—
R/W-0
(2)
(2)
SR1
SR0
C1SEN
C2REN
PULSS
PULSR
SRCLKEN
bit 7
bit 0
Legend:
S = Bit is set only -
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
(2)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
SR1: SR Latch Configuration bit
1=
0=
C2OUT pin is the latch Q output
C2OUT pin is the C2 comparator output
(2)
SR0: SR Latch Configuration bits
1=
0=
C1OUT pin is the latch Q output
C1OUT pin is the C1 Comparator output
C1SEN: C1 Set Enable bit
1= C1 comparator output sets SR latch
0= C1 comparator output has no effect on SR latch
C2REN: C2 Reset Enable bit
1= C2 comparator output resets SR latch
0= C2 comparator output has no effect on SR latch
PULSS: Pulse the SET Input of the SR Latch bit
1= Triggers pulse generator to set SR latch. Bit is immediately reset by hardware.
0= Does not trigger pulse generator
PULSR: Pulse the Reset Input of the SR Latch bit
1= Triggers pulse generator to reset SR latch. Bit is immediately reset by hardware.
0= Does not trigger pulse generator
bit 1
bit 0
Unimplemented: Read as ‘0’
SRCLKEN: SR Latch Set Clock Enable bit
1= Set input of SR latch is pulsed with SRCLK
0= Set input of SR latch is not pulsed with the SRCLK
Note 1: The C1OUT and C2OUT bits in the CMxCON0 register will always reflect the actual comparator output (not the level on
the pin), regardless of the SR latch operation.
2: To enable an SR Latch output to the pin, the appropriate CxOE, and TRIS bits must be properly configured.
REGISTER 8-5:
SRCON1: SR LATCH CONTROL 1 REGISTER
R/W-0
SRCS1
bit 7
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
SRCS0
bit 0
Legend:
S = Bit is set only -
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-6
bit 5-0
SRCS<1:0>: SR Latch Clock Prescale bits
00= FOSC/16
01= FOSC/32
10= FOSC/64
11= FOSC/128
Unimplemented: Read as ‘0’
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 67
PIC16F610/616/16HV610/616
8.11.3
OUTPUT CLAMPED TO VSS
8.11 Comparator Voltage Reference
The fixed voltage reference output voltage can be set
to Vss with no power consumption by clearing the
FVREN bit of the VRCON register (FVREN = 0). This
allows the comparator to detect a zero-crossing while
not consuming additional module current.
The comparator voltage reference module provides an
internally generated voltage reference for the compara-
tors. The following features are available:
• Independent from Comparator operation
• Two 16-level voltage ranges
• Output clamped to VSS
8.11.4
OUTPUT RATIOMETRIC TO VDD
• Ratiometric with VDD
The comparator voltage reference is VDD derived and
therefore, the CVREF output changes with fluctuations in
VDD. The tested absolute accuracy of the Comparator
Voltage Reference can be found in Section 15.0
“Electrical Specifications”.
• Fixed Reference (0.6V)
The VRCON register (Register 8-6) controls the
voltage reference module shown in Figure 8-9.
8.11.1
INDEPENDENT OPERATION
The comparator voltage reference is independent of
the comparator configuration. Setting the FVREN bit of
the VRCON register will enable the voltage reference.
8.11.2
OUTPUT VOLTAGE SELECTION
The CVREF voltage reference has 2 ranges with 16
voltage levels in each range. Range selection is
controlled by the VRR bit of the VRCON register. The
16 levels are set with the VR<3:0> bits of the VRCON
register.
The CVREF output voltage is determined by the following
equations:
EQUATION 8-1:
CVREF OUTPUT VOLTAGE
VRR = 1 (low range):
CVREF = (VR<3:0>/24) × VDD
VRR = 0 (high range):
CVREF = (VDD/4) +
(VR<3:0> × VDD/32)
The full range of VSS to VDD cannot be realized due to
the construction of the module. See Figure 8-9.
DS41288C-page 68
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
8.11.5
FIXED VOLTAGE REFERENCE
8.11.7
VOLTAGE REFERENCE
SELECTION
The fixed voltage reference is independent of VDD, with
a nominal output voltage of 0.6V. This reference can be
enabled by setting the FVREN bit of the VRCON
register to ‘1’. This reference is always enabled when
the HFINTOSC oscillator is active.
Multiplexers on the output of the voltage reference
module enable selection of either the CVREF or fixed
voltage reference for use by the comparators.
Setting the C1VREN bit of the VRCON register enables
current to flow in the CVREF voltage divider and selects
the CVREF voltage for use by C1. Clearing the C1VREN
bit selects the fixed voltage for use by C1.
8.11.6
FIXED VOLTAGE REFERENCE
STABILIZATION PERIOD
When the fixed voltage reference module is enabled, it
will require some time for the reference and its amplifier
circuits to stabilize. The user program must include a
small delay routine to allow the module to settle. See
the electrical specifications section for the minimum
delay requirement.
Setting the C2VREN bit of the VRCON register enables
current to flow in the CVREF voltage divider and selects
the CVREF voltage for use by C2. Clearing the C2VREN
bit selects the fixed voltage for use by C2.
When both the C1VREN and C2VREN bits are cleared,
current flow in the CVREF voltage divider is disabled
minimizing the power drain of the voltage reference
peripheral.
FIGURE 8-9:
COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM
16 Stages
8R
R
R
R
R
VDD
VRR
8R
Analog
MUX
15
0
CVREF
To Comparators
and ADC Module
(1)
VR<3:0>
4
C1VREN
C2VREN
To ADC Module
1.2V
0.6V
FVREN
EN
Fixed Ref
Fixed Voltage
Reference
To Comparators
and ADC Module
Note 1: Care should be taken to ensure VREF remains
within the comparator common mode input range.
See Section 15.0 “Electrical Specifications” for
more detail.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 69
PIC16F610/616/16HV610/616
REGISTER 8-6:
VRCON: VOLTAGE REFERENCE CONTROL REGISTER
R/W-0
C1VREN
bit 7
R/W-0
R/W-0
VRR
R/W-0
R/W-0
VR3
R/W-0
VR2
R/W-0
VR1
R/W-0
VR0
C2VREN
FVREN
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3-0
C1VREN: Comparator 1 Voltage Reference Enable bit
1= CVREF circuit powered on and routed to C1VREF input of Comparator C1
0= 0.6 Volt constant reference routed to C1VREF input of Comparator C1
C2VREN: Comparator 2 Voltage Reference Enable bit
1= CVREF circuit powered on and routed to C2VREF input of Comparator C2
0= 0.6 Volt constant reference routed to C2VREF input of Comparator C2
VRR: CVREF Range Selection bit
1= Low range
0= High range
FVREN: Fixed Voltage Reference (0.6V) Enable bit
1= Enabled
0= Disabled
VR<3:0>: Comparator Voltage Reference CVREF Value Selection bits (0 ≤ VR<3:0> ≤ 15)
When VRR = 1: CVREF = (VR<3:0>/24) * VDD
When VRR = 0: CVREF = VDD/4 + (VR<3:0>/32) * VDD
DS41288C-page 70
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
9.0
ANALOG-TO-DIGITAL
CONVERTER (ADC) MODULE
(PIC16F616/16HV616 ONLY)
The Analog-to-Digital Converter (ADC) allows
conversion of an analog input signal to a 10-bit binary
representation of that signal. This device uses analog
inputs, which are multiplexed into a single sample and
hold circuit. The output of the sample and hold is
connected to the input of the converter. The converter
generates a 10-bit binary result via successive
approximation and stores the conversion result into the
ADC result registers (ADRESL and ADRESH).
The ADC voltage reference is software selectable to
either VDD or a voltage applied to the external reference
pins.
The ADC can generate an interrupt upon completion of
a conversion. This interrupt can be used to wake-up the
device from Sleep.
Figure 9-1 shows the block diagram of the ADC.
FIGURE 9-1:
ADC BLOCK DIAGRAM
VDD
VCFG = 0
VCFG = 1
VREF
RA0/AN0
RA1/AN1/VREF
RA2/AN2
RA4/AN3
RC0/AN4
RC1/AN5
RC2/AN6
ADC
RC3/AN7
10
GO/DONE
CVREF
0.6V Reference
1.2V Reference
0= Left Justify
1= Right Justify
ADFM
ADON
10
4
ADRESH ADRESL
CHS <3:0>
VSS
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 71
PIC16F610/616/16HV610/616
9.1.4
CONVERSION CLOCK
9.1
ADC Configuration
The source of the conversion clock is software select-
able via the ADCS bits of the ADCON1 register. There
are seven possible clock options:
When configuring and using the ADC, the following
functions must be considered:
• Port configuration
• FOSC/2
• Channel selection
• FOSC/4
• ADC voltage reference selection
• ADC conversion clock source
• Interrupt control
• FOSC/8
• FOSC/16
• FOSC/32
• Results formatting
• FOSC/64
9.1.1
PORT CONFIGURATION
• FRC (dedicated internal oscillator)
The ADC can be used to convert both analog and digital
signals. When converting analog signals, the I/O pin
should be configured for analog by setting the associated
TRIS and ANSEL bits. See the corresponding Port
section for more information.
The time to complete one bit conversion is defined as
TAD. One full 10-bit conversion requires 11 TAD periods
as shown in Figure 9-3.
For correct conversion, the appropriate TAD specification
must be met. See A/D conversion requirements in
Section 15.0 “Electrical Specifications” for more
information. Table 9-1 gives examples of appropriate
ADC clock selections.
Note:
Analog voltages on any pin that is defined
as a digital input may cause the input
buffer to conduct excess current.
Note:
Unless using the FRC, any changes in the
system clock frequency will change the
ADC clock frequency, which may
adversely affect the ADC result.
9.1.2
CHANNEL SELECTION
The CHS bits of the ADCON0 register determine which
channel is connected to the sample and hold circuit.
When changing channels, a delay is required before
starting the next conversion. Refer to Section 9.2
“ADC Operation” for more information.
9.1.3
ADC VOLTAGE REFERENCE
The VCFG bit of the ADCON0 register provides control
of the positive voltage reference. The positive voltage
reference can be either VDD or an external voltage
source. The negative voltage reference is always
connected to the ground reference.
TABLE 9-1:
ADC CLOCK PERIOD (TAD) VS. DEVICE OPERATING FREQUENCIES (VDD > 3.0V)
ADC Clock Period (TAD)
Device Frequency (FOSC)
ADC Clock Source
ADCS<2:0>
20 MHz
8 MHz
4 MHz
1 MHz
FOSC/2
FOSC/4
FOSC/8
FOSC/16
FOSC/32
FOSC/64
FRC
000
100
001
101
010
110
x11
100 ns(2)
200 ns(2)
400 ns(2)
800 ns(2)
1.6 μs
250 ns(2)
500 ns(2)
1.0 μs(2)
2.0 μs
500 ns(2)
1.0 μs(2)
2.0 μs
2.0 μs
4.0 μs
8.0 μs(3)
16.0 μs(3)
32.0 μs(3)
64.0 μs(3)
2-6 μs(1,4)
4.0 μs
4.0 μs
8.0 μs(3)
16.0 μs(3)
2-6 μs(1,4)
3.2 μs
2-6 μs(1,4)
8.0 μs(3)
2-6 μs(1,4)
Legend: Shaded cells are outside of recommended range.
Note 1: The FRC source has a typical TAD time of 4 μs for VDD > 3.0V.
2: These values violate the minimum required TAD time.
3: For faster conversion times, the selection of another clock source is recommended.
4: When the device frequency is greater than 1 MHz, the FRC clock source is only recommended if the
conversion will be performed during Sleep.
DS41288C-page 72
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
FIGURE 9-2:
ANALOG-TO-DIGITAL CONVERSION TAD CYCLES
TCY to TAD
TAD1 TAD2 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 TAD9 TAD10 TAD11
b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
Conversion Starts
Holding Capacitor is Disconnected from Analog Input (typically 100 ns)
Set GO/DONE bit
ADRESH and ADRESL registers are loaded,
GO bit is cleared,
ADIF bit is set,
Holding capacitor is connected to analog input
9.1.5
INTERRUPTS
9.1.6
RESULT FORMATTING
The ADC module allows for the ability to generate an
interrupt upon completion of an analog-to-digital
conversion. The ADC interrupt flag is the ADIF bit in the
PIR1 register. The ADC interrupt enable is the ADIE bit
in the PIE1 register. The ADIF bit must be cleared in
software.
The 10-bit A/D conversion result can be supplied in two
formats, left justified or right justified. The ADFM bit of
the ADCON0 register controls the output format.
Figure 9-4 shows the two output formats.
Note:
The ADIF bit is set at the completion of
every conversion, regardless of whether
or not the ADC interrupt is enabled.
This interrupt can be generated while the device is
operating or while in Sleep. If the device is in Sleep, the
interrupt will wake-up the device. Upon waking from
Sleep, the next instruction following the SLEEP
instruction is always executed. If the user is attempting
to wake-up from Sleep and resume in-line code
execution, the global interrupt must be disabled. If the
global interrupt is enabled, execution will switch to the
interrupt service routine.
Please see Section 9.1.5 “Interrupts” for more
information.
FIGURE 9-3:
10-BIT A/D CONVERSION RESULT FORMAT
ADRESH
ADRESL
LSB
(ADFM = 0)
MSB
bit 7
bit 0
bit 0
bit 7
bit 7
bit 0
10-bit A/D Result
Unimplemented: Read as ‘0’
(ADFM = 1)
MSB
LSB
bit 0
bit 7
Unimplemented: Read as ‘0’
10-bit A/D Result
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 73
PIC16F610/616/16HV610/616
9.2.5
SPECIAL EVENT TRIGGER
9.2
ADC Operation
The ECCP Special Event Trigger allows periodic ADC
measurements without software intervention. When
this trigger occurs, the GO/DONE bit is set by hardware
and the Timer1 counter resets to zero.
9.2.1
STARTING A CONVERSION
To enable the ADC module, the ADON bit of the
ADCON0 register must be set to a ‘1’. Setting the GO/
DONE bit of the ADCON0 register to a ‘1’ will start the
analog-to-digital conversion.
Using the Special Event Trigger does not ensure
proper ADC timing. It is the user’s responsibility to
ensure that the ADC timing requirements are met.
Note:
The GO/DONE bit should not be set in the
same instruction that turns on the ADC.
Refer to Section 9.2.6 “A/D Conversion
Procedure”.
See Section 10.0 “Enhanced Capture/Compare/
PWM (With Auto-Shutdown and Dead Band) Mod-
ule (PIC16F616/16HV616 Only)” for more informa-
tion.
9.2.2
COMPLETION OF A CONVERSION
9.2.6
A/D CONVERSION PROCEDURE
When the conversion is complete, the ADC module will:
This is an example procedure for using the ADC to
perform an analog-to-digital conversion:
• Clear the GO/DONE bit
• Set the ADIF flag bit
1. Configure Port:
• Update the ADRESH:ADRESL registers with new
conversion result
• Disable pin output driver (See TRIS register)
• Configure pin as analog
9.2.3
TERMINATING A CONVERSION
2. Configure the ADC module:
• Select ADC conversion clock
• Configure voltage reference
• Select ADC input channel
• Select result format
If a conversion must be terminated before completion,
the GO/DONE bit can be cleared in software. The
ADRESH:ADRESL registers will not be updated with
the partially complete analog-to-digital conversion
sample. Instead, the ADRESH:ADRESL register pair
will retain the value of the previous conversion. Addi-
tionally, a 2 TAD delay is required before another acqui-
sition can be initiated. Following this delay, an input
acquisition is automatically started on the selected
channel.
• Turn on ADC module
3. Configure ADC interrupt (optional):
• Clear ADC interrupt flag
• Enable ADC interrupt
• Enable peripheral interrupt
• Enable global interrupt(1)
4. Wait the required acquisition time(2)
Note:
A device Reset forces all registers to their
Reset state. Thus, the ADC module is
turned off and any pending conversion is
terminated.
.
5. Start conversion by setting the GO/DONE bit.
6. Wait for ADC conversion to complete by one of
the following:
9.2.4
ADC OPERATION DURING SLEEP
• Polling the GO/DONE bit
The ADC module can operate during Sleep. This
requires the ADC clock source to be set to the FRC
option. When the FRC clock source is selected, the
ADC waits one additional instruction before starting the
conversion. This allows the SLEEP instruction to be
executed, which can reduce system noise during the
conversion. If the ADC interrupt is enabled, the device
will wake-up from Sleep when the conversion
completes. If the ADC interrupt is disabled, the ADC
module is turned off after the conversion completes,
although the ADON bit remains set.
• Waiting for the ADC interrupt (interrupts
enabled)
7. Read ADC Result
8. Clear the ADC interrupt flag (required if interrupt
is enabled).
Note 1: The global interrupt may be disabled if the
user is attempting to wake-up from Sleep
and resume in-line code execution.
2: See Section 9.3 “A/D Acquisition
Requirements”.
When the ADC clock source is something other than
FRC, a SLEEP instruction causes the present conver-
sion to be aborted and the ADC module is turned off,
although the ADON bit remains set.
DS41288C-page 74
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
EXAMPLE 9-1:
A/D CONVERSION
;This code block configures the ADC
;for polling, Vdd reference, Frc clock
;and AN0 input.
;
;Conversion start & polling for completion
; are included.
;
BANKSEL
MOVLW
MOVWF
BANKSEL
BSF
BANKSEL
BSF
BANKSEL
MOVLW
MOVWF
CALL
BSF
BTFSC
GOTO
BANKSEL
MOVF
MOVWF
BANKSEL
MOVF
ADCON1
;
B’01110000’ ;ADC Frc clock
ADCON1
TRISA
TRISA,0
ANSEL
ANSEL,0
ADCON0
B’10000001’ ;Right justify,
ADCON0
SampleTime
ADCON0,GO
ADCON0,GO
$-1
;
;
;Set RA0 to input
;
;Set RA0 to analog
;
;Vdd Vref, AN0, On
;Acquisiton delay
;Start conversion
;Is conversion done?
;No, test again
;
;Read upper 2 bits
;store in GPR space
;
ADRESH
ADRESH,W
RESULTHI
ADRESL
ADRESL,W
RESULTLO
;Read lower 8 bits
;Store in GPR space
MOVWF
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 75
PIC16F610/616/16HV610/616
9.2.7
ADC REGISTER DEFINITIONS
The following registers are used to control the operation of the ADC.
REGISTER 9-1:
ADCON0: A/D CONTROL REGISTER 0
R/W-0
ADFM
R/W-0
VCFG
R/W-0
CHS3
R/W-0
CHS2
R/W-0
CHS1
R/W-0
CHS0
R/W-0
R/W-0
ADON
GO/DONE
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
ADFM: A/D Conversion Result Format Select bit
1= Right justified
0= Left justified
bit 6
VCFG: Voltage Reference bit
1= VREF pin
0= VDD
bit 5-2
CHS<3:0>: Analog Channel Select bits
0000= Channel 00 (AN0)
0001= Channel 01 (AN1)
0010= Channel 02 (AN2)
0011= Channel 03 (AN3)
0100= Channel 04 (AN4)
0101= Channel 05 (AN5)
0110= Channel 06 (AN6)
0111= Channel 07 (AN7)
1000= Reserved – do not use
1001= Reserved – do not use
1010= Reserved – do not use
1011= Reserved – do not use
1100= CVREF
(1)
1101= 0.6V Fixed Voltage Reference
(1)
1110= 1.2V Fixed Voltage Reference
1111= Reserved – do not use
bit 1
bit 0
GO/DONE: A/D Conversion Status bit
1= A/D conversion cycle in progress. Setting this bit starts an A/D conversion cycle.
This bit is automatically cleared by hardware when the A/D conversion has completed.
0= A/D conversion completed/not in progress
ADON: ADC Enable bit
1= ADC is enabled
0= ADC is disabled and consumes no operating current
Note 1: When the CHS<3:0> bits change to select the 1.2V or 0.6V Fixed Voltage Reference, the reference output voltage will
have a transient. If the Comparator module uses this VP6 reference voltage, the comparator output may momentarily
change state due to the transient.
DS41288C-page 76
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
REGISTER 9-2:
ADCON1: A/D CONTROL REGISTER 1
U-0
—
R/W-0
R/W-0
R/W-0
U-0
—
U-0
—
U-0
—
U-0
—
ADCS2
ADCS1
ADCS0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
Unimplemented: Read as ‘0’
bit 6-4
ADCS<2:0>: A/D Conversion Clock Select bits
000= FOSC/2
001= FOSC/8
010= FOSC/32
x11= FRC (clock derived from a dedicated internal oscillator = 500 kHz max)
100= FOSC/4
101= FOSC/16
110= FOSC/64
bit 3-0
Unimplemented: Read as ‘0’
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 77
PIC16F610/616/16HV610/616
REGISTER 9-3:
ADRESH: ADC RESULT REGISTER HIGH (ADRESH) ADFM = 0 (READ-ONLY)
R-x
ADRES9
bit 7
R-x
R-x
R-x
R-x
R-x
R-x
R-x
ADRES8
ADRES7
ADRES6
ADRES5
ADRES4
ADRES3
ADRES2
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-0
ADRES<9:2>: ADC Result Register bits
Upper 8 bits of 10-bit conversion result
REGISTER 9-4:
ADRESL: ADC RESULT REGISTER LOW (ADRESL) ADFM = 0 (READ-ONLY)
R-x
ADRES1
bit 7
R-x
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
ADRES0
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-6
bit 5-0
ADRES<1:0>: ADC Result Register bits
Lower 2 bits of 10-bit conversion result
Reserved: Do not use.
REGISTER 9-5:
ADRESH: ADC RESULT REGISTER HIGH (ADRESH) ADFM = 1 (READ-ONLY)
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
U-0
—
R-x
R-x
ADRES9
ADRES8
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-2
bit 1-0
Reserved: Do not use.
ADRES<9:8>: ADC Result Register bits
Upper 2 bits of 10-bit conversion result
REGISTER 9-6:
ADRESL: ADC RESULT REGISTER LOW (ADRESL) ADFM = 1 (READ-ONLY)
R-x
ADRES7
bit 7
R-x
R-x
R-x
R-x
R-x
R-x
R-x
ADRES6
ADRES5
ADRES4
ADRES3
ADRES2
ADRES1
ADRES0
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-0
ADRES<7:0>: ADC Result Register bits
Lower 8 bits of 10-bit conversion result
DS41288C-page 78
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
9.3
A/D Acquisition Requirements
For the ADC to meet its specified accuracy, the charge
holding capacitor (CHOLD) must be allowed to fully
charge to the input channel voltage level. The Analog
Input model is shown in Figure 9-4. The source
impedance (RS) and the internal sampling switch (RSS)
impedance directly affect the time required to charge the
capacitor CHOLD. The sampling switch (RSS) impedance
varies over the device voltage (VDD), see Figure 9-4.
The maximum recommended impedance for analog
sources is 10 kΩ. As the source impedance is
decreased, the acquisition time may be decreased.
After the analog input channel is selected (or changed),
an A/D acquisition must be done before the conversion
can be started. To calculate the minimum acquisition
time, Equation 9-1 may be used. This equation
assumes that 1/2 LSb error is used (1024 steps for the
ADC). The 1/2 LSb error is the maximum error allowed
for the ADC to meet its specified resolution.
EQUATION 9-1:
ACQUISITION TIME EXAMPLE
Temperature = 50°C and external impedance of 10kΩ 5.0V VDD
Assumptions:
TACQ = Amplifier Settling Time + Hold Capacitor Charging Time + Temperature Coefficient
= TAMP + TC + TCOFF
= 5µs + TC + [(Temperature - 25°C)(0.05µs/°C)]
The value for TC can be approximated with the following equations:
1
2047
⎛
⎞
= VCHOLD
-----------
;[1] VCHOLD charged to within 1/2 lsb
VAPPLIED 1 –
⎝
⎠
–TC
---------
⎛
⎞
VAPPLIED 1 – e RC = VCHOLD
;[2] VCHOLD charge response to VAPPLIED
⎜
⎝
⎟
⎠
–Tc
--------
⎛
⎞
1
2047
VAPPLIED 1 – eRC = VAPPLIED 1 –
⎛
⎞
⎠
;combining [1] and [2]
-----------
⎜
⎝
⎟
⎠
⎝
Solving for TC:
TC = –CHOLD(RIC + RSS + RS) ln(1/2047)
= –10pF(1kΩ + 7kΩ + 10kΩ) ln(0.0004885)
= 1.37µs
Therefore:
TACQ = 5µS + 1.37µS + [(50°C- 25°C)(0.05µS/°C)]
= 7.67µS
Note 1: The reference voltage (VREF) has no effect on the equation, since it cancels itself out.
2: The charge holding capacitor (CHOLD) is not discharged after each conversion.
3: The maximum recommended impedance for analog sources is 10 kΩ. This is required to meet the pin
leakage specification.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 79
PIC16F610/616/16HV610/616
FIGURE 9-4:
ANALOG INPUT MODEL
VDD
Sampling
Switch
VT = 0.6V
ANx
SS
RIC ≤ 1k
Rss
Rs
CPIN
5 pF
VA
I LEAKAGE
± 500 nA
CHOLD = 10 pF
VSS/VREF-
VT = 0.6V
6V
5V
RSS
VDD 4V
3V
Legend: CPIN
= Input Capacitance
= Threshold Voltage
VT
2V
I LEAKAGE = Leakage current at the pin due to
various junctions
RIC
SS
CHOLD
= Interconnect Resistance
= Sampling Switch
= Sample/Hold Capacitance
5 6 7 8 9 1011
Sampling Switch
(kΩ)
FIGURE 9-5:
ADC TRANSFER FUNCTION
Full-Scale Range
3FFh
3FEh
3FDh
3FCh
3FBh
1 LSB ideal
Full-Scale
Transition
004h
003h
002h
001h
000h
Analog Input Voltage
1 LSB ideal
Zero-Scale
Transition
VDD/VREF+
VSS/VREF-
DS41288C-page 80
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 9-2:
SUMMARY OF ASSOCIATED ADC REGISTERS
Value on
all other
Resets
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ADCON0(1)
ADFM
VCFG
CHS3
CHS2
CHS1
CHS0
ADON
0000 0000
0000 0000
GO/DONE
—
ADCON1(1)
ANSEL
ADRESH
ADRESL
INTCON
PIE1
—
ADCS2
ANS6
ADCS1
ANS5
ADCS0
ANS4
—
—
—
-000 ----
1111 1111
xxxx xxxx
xxxx xxxx
0000 0000
-000 0-00
-000 0-00
--x0 x000
--xx 00xx
--11 1111
--11 1111
-000 ----
1111 1111
uuuu uuuu
uuuu uuuu
0000 0000
-000 0-00
-000 0-00
--u0 u000
--uu 00uu
--11 1111
--11 1111
ANS
ANS3
ANS2
ANS1
ANS0
A/D Result Register High Byte
A/D Result Register Low Byte
GIE
—
PEIE
ADIE(1)
ADIF(1)
—
T0IE
CCP1IE(1)
CCP1IF(1)
RA5
INTE
C2IE
RAIE
C1IE
T0IF
—
INTF
TMR2IE(1)
TMR2IF(1)
RA1
RAIF
TMR1IE
TMR1IF
RA0
PIR1
—
C2IF
C1IF
—
PORTA
PORTC
TRISA
—
RA4
RA3
RA2
—
—
RC5
RC4
RC3
RC2
RC1
RC0
—
—
TRISA5
TRISC5
TRISA4
TRISC4
TRISA3
TRISC3
TRISA2
TRISC2
TRISA1
TRISC1
TRISA0
TRISC0
TRISC
—
—
Legend:
x= unknown, u= unchanged, – =unimplemented read as ‘0’. Shaded cells are not used for ADC module.
Note 1:
PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 81
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 82
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
event when a predetermined amount of time has
expired. The PWM mode can generate a Pulse-Width
Modulated signal of varying frequency and duty cycle.
10.0 ENHANCED CAPTURE/
COMPARE/PWM (WITH AUTO-
SHUTDOWN AND DEAD BAND)
MODULE
Table 10-1 shows the timer resources required by the
ECCP module.
(PIC16F616/16HV616 ONLY)
TABLE 10-1: ECCP MODE – TIMER
RESOURCES REQUIRED
The Enhanced Capture/Compare/PWM module is a
peripheral which allows the user to time and control
different events. In Capture mode, the peripheral
allows the timing of the duration of an event. The
Compare mode allows the user to trigger an external
ECCP Mode
Timer Resource
Capture
Compare
PWM
Timer1
Timer1
Timer2
REGISTER 10-1: CCP1CON: ENHANCED CCP1 CONTROL REGISTER
R/W-0
P1M1
R/W-0
P1M0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
CCP1M1
R/W-0
DC1B1
DC1B0
CCP1M3
CCP1M2
CCP1M0
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7-6
P1M<1:0>: PWM Output Configuration bits
If CCP1M<3:2> = 00, 01, 10:
xx= P1A assigned as Capture/Compare input; P1B, P1C, P1D assigned as port pins
If CCP1M<3:2> = 11:
00= Single output; P1A modulated; P1B, P1C, P1D assigned as port pins
01= Full-Bridge output forward; P1D modulated; P1A active; P1B, P1C inactive
10= Half-Bridge output; P1A, P1B modulated with dead-time control; P1C, P1D assigned as port pins
11= Full-Bridge output reverse; P1B modulated; P1C active; P1A, P1D inactive
bit 5-4
DC1B<1:0>: PWM Duty Cycle Least Significant bits
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L.
bit 3-0
CCP1M<3:0>: ECCP Mode Select bits
0000= Capture/Compare/PWM off (resets ECCP module)
0001= Unused (reserved)
0010= Compare mode, toggle output on match (CCP1IF bit is set)
0011= Unused (reserved)
0100= Capture mode, every falling edge
0101= Capture mode, every rising edge
0110= Capture mode, every 4th rising edge
0111= Capture mode, every 16th rising edge
1000= Compare mode, set output on match (CCP1IF bit is set)
1001= Compare mode, clear output on match (CCP1IF bit is set)
1010= Compare mode, generate software interrupt on match (CCP1IF bit is set, CCP1 pin is unaffected)
1011= Compare mode, trigger special event (CCP1IF bit is set; CCP1 resets TMR1 and starts an A/D
conversion, if the ADC module is enabled)
1100= PWM mode; P1A, P1C active-high; P1B, P1D active-high
1101= PWM mode; P1A, P1C active-high; P1B, P1D active-low
1110= PWM mode; P1A, P1C active-low; P1B, P1D active-high
1111= PWM mode; P1A, P1C active-low; P1B, P1D active-low
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 83
PIC16F610/616/16HV610/616
10.1.2
TIMER1 MODE SELECTION
10.1 Capture Mode
Timer1 must be running in Timer mode or Synchronized
Counter mode for the CCP module to use the capture
feature. In Asynchronous Counter mode, the capture
operation may not work.
In Capture mode, CCPR1H:CCPR1L captures the
16-bit value of the TMR1 register when an event occurs
on pin CCP1. An event is defined as one of the
following and is configured by the CCP1M<3:0> bits of
the CCP1CON register:
10.1.3
SOFTWARE INTERRUPT
• Every falling edge
• Every rising edge
When the Capture mode is changed, a false capture
interrupt may be generated. The user should keep the
CCP1IE interrupt enable bit of the PIE1 register clear to
avoid false interrupts. Additionally, the user should
clear the CCP1IF interrupt flag bit of the PIR1 register
following any change in operating mode.
• Every 4th rising edge
• Every 16th rising edge
When a capture is made, the Interrupt Request Flag bit
CCP1IF of the PIR1 register is set. The interrupt flag
must be cleared in software. If another capture occurs
before the value in the CCPR1H, CCPR1L register pair
is read, the old captured value is overwritten by the new
captured value (see Figure 10-1).
10.1.4
CCP PRESCALER
There are four prescaler settings specified by the
CCP1M<3:0> bits of the CCP1CON register.
Whenever the CCP module is turned off, or the CCP
module is not in Capture mode, the prescaler counter
is cleared. Any Reset will clear the prescaler counter.
10.1.1
CCP1 PIN CONFIGURATION
In Capture mode, the CCP1 pin should be configured
as an input by setting the associated TRIS control bit.
Switching from one capture prescaler to another does not
clear the prescaler and may generate a false interrupt. To
avoid this unexpected operation, turn the module off by
clearing the CCP1CON register before changing the
prescaler (see Example 10-1).
Note:
If the CCP1 pin is configured as an output,
a write to the port can cause a capture
condition.
FIGURE 10-1:
CAPTURE MODE
OPERATION BLOCK
DIAGRAM
EXAMPLE 10-1:
CHANGING BETWEEN
CAPTURE PRESCALERS
BANKSELCCP1CON
;Set Bank bits to point
;to CCP1CON
;Turn CCP module off
Set Flag bit CCP1IF
(PIR1 register)
Prescaler
÷ 1, 4, 16
CLRF
CCP1CON
MOVLW
NEW_CAPT_PS;Load the W reg with
; the new prescaler
CCP1
pin
CCPR1H
CCPR1L
; move value and CCP ON
Capture
Enable
MOVWF
CCP1CON
;Load CCP1CON with this
; value
and
Edge Detect
TMR1H
TMR1L
CCP1CON<3:0>
System Clock (FOSC)
DS41288C-page 84
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 10-2: SUMMARY OF REGISTERS ASSOCIATED WITH CAPTURE
Value on
all other
Resets
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CCP1CON(1)
CCPR1L(1)
CCPR1H(1)
INTCON
P1M1
P1M0
DC1B1
DC1B0
CCP1M3
CCP1M2
CCP1M1
CCP1M0
0000 0000
xxxx xxxx
xxxx xxxx
0000 0000
uuuu uuuu
uuuu uuuu
Capture/Compare/PWM Register 1 Low Byte
Capture/Compare/PWM Register 1 High Byte
GIE
PEIE
T0IE
INTE
RAIE
T0IF
INTF
RAIF
0000 0000
-000 0-00
-000 0-00
0000 0000
xxxx xxxx
xxxx xxxx
--11 1111
--11 1111
0000 0000
0000 0-00
0000 0-00
uuuu uuuu
uuuu uuuu
uuuu uuuu
--11 1111
--11 1111
PIE1
—
—
ADIE(1)
ADIF(1)
CCP1IE(1)
CCP1IF(1)
C2IE
C2IF
C1IE
C1IF
—
—
TMR2IE(1)
TMR2IF(1)
TMR1CS
TMR1IE
TMR1IF
TMR1ON
PIR1
T1CON
TMR1L
TMR1H
TRISA
TRISC
T1GINV
TMR1GE T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register
Holding Register for the Most Significant Byte of the 16-bit TMR1 Register
—
—
—
—
TRISA5
TRISC5
TRISA4
TRISC4
TRISA3
TRISC3
TRISA2
TRISC2
TRISA1
TRISC1
TRISA0
TRISC0
Legend: – = Unimplemented locations, read as ‘0’, u= unchanged, x= unknown. Shaded cells are not used by the Capture, Compare and PWM.
Note 1: PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 85
PIC16F610/616/16HV610/616
10.2.2
TIMER1 MODE SELECTION
10.2 Compare Mode
In Compare mode, Timer1 must be running in either
Timer mode or Synchronized Counter mode. The
compare operation may not work in Asynchronous
Counter mode.
In Compare mode, the 16-bit CCPR1 register value is
constantly compared against the TMR1 register pair
value. When a match occurs, the CCP1 module may:
• Toggle the CCP1 output
• Set the CCP1 output
10.2.3
SOFTWARE INTERRUPT MODE
• Clear the CCP1 output
When Generate Software Interrupt mode is chosen
(CCP1M<3:0> = 1010), the CCP1 module does not
assert control of the CCP1 pin (see the CCP1CON
register).
• Generate a Special Event Trigger
• Generate a Software Interrupt
The action on the pin is based on the value of the
CCP1M<3:0> control bits of the CCP1CON register.
10.2.4
SPECIAL EVENT TRIGGER
All Compare modes can generate an interrupt.
When Special Event Trigger mode is chosen
(CCP1M<3:0> = 1011), the CCP1 module does the
following:
FIGURE 10-2:
COMPARE MODE
OPERATION BLOCK
DIAGRAM
• Resets Timer1
• Starts an ADC conversion if ADC is enabled
CCP1CON<3:0>
Mode Select
The CCP1 module does not assert control of the CCP1
pin in this mode (see the CCP1CON register).
Set CCP1IF Interrupt Flag
The Special Event Trigger output of the CCP occurs
immediately upon a match between the TMR1H,
TMR1L register pair and the CCPR1H, CCPR1L
register pair. The TMR1H, TMR1L register pair is not
reset until the next rising edge of the Timer1 clock. This
allows the CCPR1H, CCPR1L register pair to
effectively provide a 16-bit programmable period
register for Timer1.
(PIR1)
4
CCP1
Pin
CCPR1H CCPR1L
Comparator
Q
S
R
Output
Logic
Match
TMR1H TMR1L
TRIS
Output Enable
Special Event Trigger
Note 1: The Special Event Trigger from the CCP
module does not set interrupt flag bit
TMR1IF of the PIR1 register.
Special Event Trigger will:
•
•
•
Clear TMR1H and TMR1L registers.
NOT set interrupt flag bit TMR1IF of the PIR1 register.
Set the GO/DONE bit to start the ADC conversion.
2: Removing the match condition by
changing the contents of the CCPR1H
and CCPR1L register pair, between the
clock edge that generates the Special
Event Trigger and the clock edge that
generates the Timer1 Reset, will preclude
the Reset from occurring.
10.2.1
CCP1 PIN CONFIGURATION
The user must configure the CCP1 pin as an output by
clearing the associated TRIS bit.
Note:
Clearing the CCP1CON register will force
the CCP1 compare output latch to the
default low level. This is not the PORT I/O
data latch.
DS41288C-page 86
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 10-3: SUMMARY OF REGISTERS ASSOCIATED WITH COMPARE
Value on
all other
Resets
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CCP1CON(1)
CCPR1L(1)
CCPR1H(1)
INTCON
P1M1
P1M0
DC1B1
DC1B0
CCP1M3
CCP1M2
CCP1M1
CCP1M0
0000 0000
xxxx xxxx
xxxx xxxx
0000 0000
uuuu uuuu
uuuu uuuu
Capture/Compare/PWM Register 1 Low Byte
Capture/Compare/PWM Register 1 High Byte
GIE
PEIE
T0IE
INTE
RAIE
T0IF
INTF
RAIF
0000 0000
-000 0-00
-000 0-00
0000 0000
xxxx xxxx
xxxx xxxx
--11 1111
--11 1111
0000 0000
0000 0-00
0000 0-00
uuuu uuuu
uuuu uuuu
uuuu uuuu
--11 1111
--11 1111
PIE1
—
—
ADIE(1)
ADIF(1)
CCP1IE(1)
CCP1IF(1)
C2IE
C2IF
C1IE
C1IF
—
—
TMR2IE(1)
TMR2IF(1)
TMR1CS
TMR1IE
TMR1IF
TMR1ON
PIR1
T1CON
TMR1L
TMR1H
TRISA
TRISC
T1GINV
TMR1GE T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register
Holding Register for the Most Significant Byte of the 16-bit TMR1 Register
—
—
—
—
TRISA5
TRISC5
TRISA4
TRISC4
TRISA3
TRISC3
TRISA2
TRISC2
TRISA1
TRISC1
TRISA0
TRISC0
Legend: – = Unimplemented locations, read as ‘0’, u= unchanged, x= unknown. Shaded cells are not used by the Capture, Compare and PWM.
Note 1: PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 87
PIC16F610/616/16HV610/616
The PWM output (Figure 10-4) has a time base
(period) and a time that the output stays high (duty
cycle).
10.3 PWM Mode
The PWM mode generates a Pulse-Width Modulated
signal on the CCP1 pin. The duty cycle, period and
resolution are determined by the following registers:
FIGURE 10-4:
CCP PWM OUTPUT
• PR2
Period
• T2CON
• CCPR1L
• CCP1CON
Pulse Width
TMR2 = PR2
TMR2 = CCPR1L:CCP1CON<5:4>
In Pulse-Width Modulation (PWM) mode, the CCP
module produces up to a 10-bit resolution PWM output
on the CCP1 pin. Since the CCP1 pin is multiplexed
with the PORT data latch, the TRIS for that pin must be
cleared to make the CCP1 pin an output.
TMR2 = 0
Note:
Clearing the CCP1CON register will
relinquish CCP1 control of the CCP1 pin.
Figure 10-3 shows a simplified block diagram of PWM
operation.
Figure 10-4 shows a typical waveform of the PWM
signal.
For a step-by-step procedure on how to set up the CCP
module for PWM operation, see Section 10.3.7
“Setup for PWM Operation”.
FIGURE 10-3:
SIMPLIFIED PWM BLOCK
DIAGRAM
CCP1CON<5:4>
Duty Cycle Registers
CCPR1L
CCPR1H(2) (Slave)
Comparator
CCP1
R
S
Q
(1)
TMR2
TRIS
Comparator
PR2
Clear Timer2,
toggle CCP1 pin and
latch duty cycle
Note 1: The 8-bit timer TMR2 register is concatenated
with the 2-bit internal system clock (FOSC), or
2 bits of the prescaler, to create the 10-bit time
base.
2: In PWM mode, CCPR1H is a read-only register.
DS41288C-page 88
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
10.3.1
PWM PERIOD
EQUATION 10-2: PULSE WIDTH
The PWM period is specified by writing to the PR2
register of Timer2. The PWM period can be calculated
using the formula of Equation 10-1.
Pulse Width = (CCPR1L:CCP1CON<5:4>) •
TOSC • (TMR2 Prescale Value)
EQUATION 10-1: PWM PERIOD
EQUATION 10-3: DUTY CYCLE RATIO
PWM Period = [(PR2) + 1] • 4 • TOSC •
(TMR2 Prescale Value)
(CCPR1L:CCP1CON<5:4>)
Duty Cycle Ratio = -----------------------------------------------------------------------
4(PR2 + 1)
When TMR2 is equal to PR2, the following three events
occur on the next increment cycle:
The CCPR1H register and a 2-bit internal latch are
used to double buffer the PWM duty cycle. This double
buffering is essential for glitchless PWM operation.
• TMR2 is cleared
• The CCP1 pin is set. (Exception: If the PWM duty
cycle = 0%, the pin will not be set.)
The 8-bit timer TMR2 register is concatenated with
either the 2-bit internal system clock (FOSC), or 2 bits of
the prescaler, to create the 10-bit time base. The system
clock is used if the Timer2 prescaler is set to 1:1.
• The PWM duty cycle is latched from CCPR1L into
CCPR1H.
Note:
The Timer2 postscaler (see Section 7.1
“Timer2 Operation”) is not used in the
determination of the PWM frequency.
When the 10-bit time base matches the CCPR1H and
2-bit latch, then the CCP1 pin is cleared (see
Figure 10-3).
10.3.2
PWM DUTY CYCLE
10.3.3
PWM RESOLUTION
The PWM duty cycle is specified by writing a 10-bit
value to multiple registers: CCPR1L register and
CCP1<1:0> bits of the CCP1CON register. The
CCPR1L contains the eight MSbs and the CCP1<1:0>
bits of the CCP1CON register contain the two LSbs.
CCPR1L and CCP1<1:0> bits of the CCP1CON
register can be written to at any time. The duty cycle
value is not latched into CCPR1H until after the period
completes (i.e., a match between PR2 and TMR2
registers occurs). While using the PWM, the CCPR1H
register is read-only.
The resolution determines the number of available duty
cycles for a given period. For example, a 10-bit resolution
will result in 1024 discrete duty cycles, whereas an 8-bit
resolution will result in 256 discrete duty cycles.
The maximum PWM resolution is 10 bits when PR2 is
255. The resolution is a function of the PR2 register
value as shown by Equation 10-4.
EQUATION 10-4: PWM RESOLUTION
log[4(PR2 + 1)]
Equation 10-2 is used to calculate the PWM pulse
width.
Resolution = ----------------------------------------- bits
log(2)
Equation 10-3 is used to calculate the PWM duty cycle
ratio.
Note:
If the pulse width value is greater than the
period the assigned PWM pin(s) will
remain unchanged.
TABLE 10-4: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 20 MHz)
PWM Frequency
1.22 kHz
4.88 kHz
19.53 kHz
78.12 kHz
156.3 kHz
208.3 kHz
Timer Prescale (1, 4, 16)
PR2 Value
16
0xFF
10
4
1
1
0x3F
8
1
0x1F
7
1
0xFF
10
0xFF
10
0x17
6.6
Maximum Resolution (bits)
TABLE 10-5: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 8 MHz)
PWM Frequency
1.22 kHz
4.90 kHz
19.61 kHz
76.92 kHz
153.85 kHz 200.0 kHz
Timer Prescale (1, 4, 16)
PR2 Value
16
0x65
8
4
0x65
8
1
0x65
8
1
0x19
6
1
0x0C
5
1
0x09
5
Maximum Resolution (bits)
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 89
PIC16F610/616/16HV610/616
10.3.4
OPERATION IN SLEEP MODE
10.3.7
SETUP FOR PWM OPERATION
In Sleep mode, the TMR2 register will not increment
and the state of the module will not change. If the CCP1
pin is driving a value, it will continue to drive that value.
When the device wakes up, TMR2 will continue from its
previous state.
The following steps should be taken when configuring
the CCP module for PWM operation:
1. Configure the PWM pin (CCP1) as an input by
setting the associated TRIS bit.
2. Set the PWM period by loading the PR2 register.
3. Configure the CCP module for the PWM mode
by loading the CCP1CON register with the
appropriate values.
10.3.5
CHANGES IN SYSTEM CLOCK
FREQUENCY
The PWM frequency is derived from the system clock
frequency. Any changes in the system clock frequency
will result in changes to the PWM frequency. See
Section 3.0 “Oscillator Module” for additional
details.
4. Set the PWM duty cycle by loading the CCPR1L
register and CCP1 bits of the CCP1CON register.
5. Configure and start Timer2:
• Clear the TMR2IF interrupt flag bit of the
PIR1 register.
10.3.6
EFFECTS OF RESET
• Set the Timer2 prescale value by loading the
T2CKPS bits of the T2CON register.
Any Reset will force all ports to Input mode and the
CCP registers to their Reset states.
• Enable Timer2 by setting the TMR2ON bit of
the T2CON register.
6. Enable PWM output after a new PWM cycle has
started:
• Wait until Timer2 overflows (TMR2IF bit of
the PIR1 register is set).
• Enable the CCP1 pin output by clearing the
associated TRIS bit.
DS41288C-page 90
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
The PWM outputs are multiplexed with I/O pins and are
designated P1A, P1B, P1C and P1D. The polarity of the
PWM pins is configurable and is selected by setting the
CCP1M bits in the CCP1CON register appropriately.
10.4 PWM (Enhanced Mode)
The Enhanced PWM Mode can generate a PWM signal
on up to four different output pins with up to 10-bits of
resolution. It can do this through four different PWM
Output modes:
Table 10-6 shows the pin assignments for each
Enhanced PWM mode.
• Single PWM
Figure 10-5 shows an example of a simplified block
diagram of the Enhanced PWM module.
• Half-Bridge PWM
• Full-Bridge PWM, Forward mode
• Full-Bridge PWM, Reverse mode
Note:
To prevent the generation of an
incomplete waveform when the PWM is
first enabled, the ECCP module waits until
the start of a new PWM period before
generating a PWM signal.
To select an Enhanced PWM mode, the P1M bits of the
CCP1CON register must be set appropriately.
FIGURE 10-5:
EXAMPLE SIMPLIFIED BLOCK DIAGRAM OF THE ENHANCED PWM MODE
CCP1<1:0>
P1M<1:0>
CCP1M<3:0>
4
Duty Cycle Registers
2
CCPR1L
CCP1/P1A
CCP1/P1A
TRISC<5>
TRISC<4>
TRISC<3>
TRISC<2>
CCPR1H (Slave)
Comparator
P1B
P1B
P1C
Output
Controller
R
S
Q
P1C
(1)
TMR2
P1D
P1D
Comparator
PR2
Clear Timer2,
toggle PWM pin and
latch duty cycle
PWM1CON
Note 1: The 8-bit timer TMR2 register is concatenated with the 2-bit internal Q clock, or 2 bits of the prescaler to create the 10-bit
time base.
Note 1: The TRIS register value for each PWM output must be configured appropriately.
2: Clearing the CCP1CON register will relinquish ECCP control of all PWM output pins.
3: Any pin not used by an Enhanced PWM mode is available for alternate pin functions
TABLE 10-6: EXAMPLE PIN ASSIGNMENTS FOR VARIOUS PWM ENHANCED MODES
ECCP Mode
P1M
CCP1/P1A
P1B
P1C
P1D
Single
00
10
01
11
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
No
No
No
No
Half-Bridge
Full-Bridge, Forward
Full-Bridge, Reverse
Yes
Yes
Yes
Yes
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 91
PIC16F610/616/16HV610/616
FIGURE 10-6:
EXAMPLE PWM (ENHANCED MODE) OUTPUT RELATIONSHIPS (ACTIVE-HIGH
STATE)
PR2+1
Pulse
Width
0
Signal
P1M<1:0>
Period
P1A Modulated
(Single Output)
00
10
Delay(1)
Delay(1)
P1A Modulated
P1B Modulated
P1A Active
(Half-Bridge)
P1B Inactive
(Full-Bridge,
Forward)
01
P1C Inactive
P1D Modulated
P1A Inactive
P1B Modulated
P1C Active
(Full-Bridge,
Reverse)
11
P1D Inactive
Relationships:
•
•
•
Period = 4 * TOSC * (PR2 + 1) * (TMR2 Prescale Value)
Pulse Width = TOSC * (CCPR1L<7:0>:CCP1CON<5:4>) * (TMR2 Prescale Value)
Delay = 4 * TOSC * (PWM1CON<6:0>)
Note 1: Dead-band delay is programmed using the PWM1CON register (Section 10.4.6 “Programmable Dead-Band Delay
mode”).
DS41288C-page 92
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
FIGURE 10-7:
EXAMPLE ENHANCED PWM OUTPUT RELATIONSHIPS (ACTIVE-LOW STATE)
PR2+1
Pulse
Width
0
Signal
P1M<1:0>
Period
P1A Modulated
P1A Modulated
P1B Modulated
P1A Active
(Single Output)
00
10
Delay(1)
Delay(1)
(Half-Bridge)
(Full-Bridge,
Forward)
P1B Inactive
P1C Inactive
P1D Modulated
P1A Inactive
P1B Modulated
P1C Active
01
(Full-Bridge,
Reverse)
11
P1D Inactive
Relationships:
•
•
•
Period = 4 * TOSC * (PR2 + 1) * (TMR2 Prescale Value)
Pulse Width = TOSC * (CCPR1L<7:0>:CCP1CON<5:4>) * (TMR2 Prescale Value)
Delay = 4 * TOSC * (PWM1CON<6:0>)
Note 1: Dead-band delay is programmed using the PWM1CON register (Section 10.4.6 “Programmable Dead-Band Delay
mode”).
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 93
PIC16F610/616/16HV610/616
Since the P1A and P1B outputs are multiplexed with
the PORT data latches, the associated TRIS bits must
be cleared to configure P1A and P1B as outputs.
10.4.1
HALF-BRIDGE MODE
In Half-Bridge mode, two pins are used as outputs to
drive push-pull loads. The PWM output signal is output
on the CCP1/P1A pin, while the complementary PWM
output signal is output on the P1B pin (see Figure 10-8).
This mode can be used for half-bridge applications, as
shown in Figure 10-9, or for full-bridge applications,
where four power switches are being modulated with
two PWM signals.
FIGURE 10-8:
EXAMPLE OF HALF-
BRIDGE PWM OUTPUT
Period
Period
Pulse Width
(2)
(2)
P1A
In Half-Bridge mode, the programmable dead-band delay
can be used to prevent shoot-through current in half-
bridge power devices. The value of the PDC<6:0> bits of
the PWM1CON register sets the number of instruction
cycles before the output is driven active. If the value is
greater than the duty cycle, the corresponding output
remains inactive during the entire cycle. See 10.4.6
“Programmable Dead-Band Delay mode” for more
details of the dead-band delay operations.
td
td
P1B
(1)
(1)
(1)
td = Dead-Band Delay
Note 1: At this time, the TMR2 register is equal to the
PR2 register.
2: Output signals are shown as active-high.
FIGURE 10-9:
EXAMPLE OF HALF-BRIDGE APPLICATIONS
Standard Half-Bridge Circuit (“Push-Pull”)
FET
Driver
+
-
P1A
Load
FET
Driver
+
-
P1B
Half-Bridge Output Driving a Full-Bridge Circuit
V+
FET
Driver
FET
Driver
P1A
Load
FET
FET
Driver
Driver
P1B
DS41288C-page 94
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
10.4.2
FULL-BRIDGE MODE
In Full-Bridge mode, all four pins are used as outputs.
An example of full-bridge application is shown in
Figure 10-10.
In the Forward mode, pin CCP1/P1A is driven to its active
state, pin P1D is modulated, while P1B and P1C will be
driven to their inactive state as shown in Figure 10-11.
In the Reverse mode, P1C is driven to its active state,
pin P1B is modulated, while P1A and P1D will be driven
to their inactive state as shown Figure 10-11.
P1A, P1B, P1C and P1D outputs are multiplexed with
the PORT data latches. The associated TRIS bits must
be cleared to configure the P1A, P1B, P1C and P1D
pins as outputs.
FIGURE 10-10:
EXAMPLE OF FULL-BRIDGE APPLICATION
V+
QC
QA
FET
Driver
FET
Driver
P1A
P1B
Load
FET
Driver
FET
Driver
P1C
P1D
QD
QB
V-
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 95
PIC16F610/616/16HV610/616
FIGURE 10-11:
EXAMPLE OF FULL-BRIDGE PWM OUTPUT
Forward Mode
Period
(2)
P1A
Pulse Width
(2)
P1B
(2)
P1C
(2)
P1D
(1)
(1)
Reverse Mode
Period
Pulse Width
(2)
P1A
(2)
P1B
(2)
P1C
(2)
P1D
(1)
(1)
Note 1: At this time, the TMR2 register is equal to the PR2 register.
2: Output signal is shown as active-high.
DS41288C-page 96
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
The Full-Bridge mode does not provide dead-band
delay. As one output is modulated at a time, dead-band
delay is generally not required. There is a situation
where dead-band delay is required. This situation
occurs when both of the following conditions are true:
10.4.2.1
Direction Change in Full-Bridge
Mode
In the Full-Bridge mode, the P1M1 bit in the CCP1CON
register allows users to control the forward/reverse
direction. When the application firmware changes this
direction control bit, the module will change to the new
direction on the next PWM cycle.
1. The direction of the PWM output changes when
the duty cycle of the output is at or near 100%.
2. The turn off time of the power switch, including
the power device and driver circuit, is greater
than the turn on time.
A direction change is initiated in software by changing
the P1M1 bit of the CCP1CON register. The following
sequence occurs four Timer2 cycles prior to the end of
the current PWM period:
Figure 10-13 shows an example of the PWM direction
changing from forward to reverse, at a near 100% duty
cycle. In this example, at time t1, the output P1A and
P1D become inactive, while output P1C becomes
active. Since the turn off time of the power devices is
longer than the turn on time, a shoot-through current
will flow through power devices QC and QD (see
Figure 10-10) for the duration of ‘t’. The same
phenomenon will occur to power devices QA and QB
for PWM direction change from reverse to forward.
• The modulated outputs (P1B and P1D) are placed
in their inactive state.
• The associated unmodulated outputs (P1A and
P1C) are switched to drive in the opposite
direction.
• PWM modulation resumes at the beginning of the
next period.
See Figure 10-12 for an illustration of this sequence.
If changing PWM direction at high duty cycle is required
for an application, two possible solutions for eliminating
the shoot-through current are:
1. Reduce PWM duty cycle for one PWM period
before changing directions.
2. Use switch drivers that can drive the switches off
faster than they can drive them on.
Other options to prevent shoot-through current may
exist.
FIGURE 10-12:
EXAMPLE OF PWM DIRECTION CHANGE
(1)
Period
Period
Signal
P1A (Active-High)
P1B (Active-High)
Pulse Width
P1C (Active-High)
P1D (Active-High)
(2)
Pulse Width
Note 1: The direction bit P1M1 of the CCP1CON register is written any time during the PWM cycle.
2: When changing directions, the P1A and P1C signals switch before the end of the current PWM cycle. The
modulated P1B and P1D signals are inactive at this time. The length of this time is four Timer2 counts.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 97
PIC16F610/616/16HV610/616
FIGURE 10-13:
EXAMPLE OF PWM DIRECTION CHANGE AT NEAR 100% DUTY CYCLE
Forward Period
Reverse Period
t1
P1A
P1B
DC
P1C
P1D
PW
TON
External Switch C
External Switch D
TOFF
Potential
T = TOFF – TON
Shoot-Through Current
Note 1: All signals are shown as active-high.
2: TON is the turn on delay of power switch QC and its driver.
3: TOFF is the turn off delay of power switch QD and its driver.
DS41288C-page 98
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
10.4.3
START-UP CONSIDERATIONS
When any PWM mode is used, the application
hardware must use the proper external pull-up and/or
pull-down resistors on the PWM output pins.
Note:
When the microcontroller is released from
Reset, all of the I/O pins are in the high-
impedance state. The external circuits
must keep the power switch devices in the
OFF state until the microcontroller drives
the I/O pins with the proper signal levels or
activates the PWM output(s).
The CCP1M<1:0> bits of the CCP1CON register allow
the user to choose whether the PWM output signals are
active-high or active-low for each pair of PWM output pins
(P1A/P1C and P1B/P1D). The PWM output polarities
must be selected before the PWM pins are configured as
outputs. Changing the polarity configuration while the
PWM pins are configured as outputs is not recommended
since it may result in damage to the application circuits.
The P1A, P1B, P1C and P1D output latches may not be
in the proper states when the PWM module is
initialized. Enabling the PWM pins for output at the
same time as the Enhanced PWM modes may cause
damage to the application circuit. The Enhanced PWM
modes must be enabled in the proper Output mode and
complete a full PWM cycle before configuring the PWM
pins as outputs. The completion of a full PWM cycle is
indicated by the TMR2IF bit of the PIR1 register being
set as the second PWM period begins.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 99
PIC16F610/616/16HV610/616
A shutdown condition is indicated by the ECCPASE
(Auto-Shutdown Event Status) bit of the ECCPAS
register. If the bit is a ‘0’, the PWM pins are operating
normally. If the bit is a ‘1’, the PWM outputs are in the
shutdown state.
10.4.4
ENHANCED PWM AUTO-
SHUTDOWN MODE
The PWM mode supports an Auto-Shutdown mode that
will disable the PWM outputs when an external
shutdown event occurs. Auto-Shutdown mode places
the PWM output pins into a predetermined state. This
mode is used to help prevent the PWM from damaging
the application.
When a shutdown event occurs, two things happen:
The ECCPASE bit is set to ‘1’. The ECCPASE will
remain set until cleared in firmware or an auto-restart
occurs (see Section 10.4.5 “Auto-Restart Mode”).
The auto-shutdown sources are selected using the
ECCPASx bits of the ECCPAS register. A shutdown
event may be generated by:
The enabled PWM pins are asynchronously placed in
their shutdown states. The PWM output pins are
grouped into pairs [P1A/P1C] and [P1B/P1D]. The state
of each pin pair is determined by the PSSAC and
PSSBD bits of the ECCPAS register. Each pin pair may
be placed into one of three states:
• A logic ‘0’ on the INT pin
• Comparator C1
• Comparator C2
• Setting the ECCPASE bit in firmware
• Drive logic ‘1’
• Drive logic ‘0’
• Tri-state (high-impedance)
REGISTER 10-2: ECCPAS: ENHANCED CAPTURE/COMPARE/PWM AUTO-SHUTDOWN
CONTROL REGISTER
R/W-0
U-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
ECCPASE
ECCPAS2
ECCPAS1
ECCPAS0
PSSAC1
PSSAC0
PSSBD1
PSSBD0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 7
ECCPASE: ECCP Auto-Shutdown Event Status bit
1= A shutdown event has occurred; ECCP outputs are in shutdown state
0= ECCP outputs are operating
bit 6-4
ECCPAS<2:0>: ECCP Auto-shutdown Source Select bits
000= Auto-Shutdown is disabled
001= Comparator C1 output high
010= Comparator C2 output high(1)
011= Either Comparators output is high
100= VIL on INT pin
101= VIL on INT pin or Comparator C1 output high
110= VIL on INT pin or Comparator C2 output high
111= VIL on INT pin or either Comparators output is high
bit 3-2
bit 1-0
PSSACn: Pins P1A and P1C Shutdown State Control bits
00= Drive pins P1A and P1C to ‘0’
01= Drive pins P1A and P1C to ‘1’
1x= Pins P1A and P1C tri-state
PSSBDn: Pins P1B and P1D Shutdown State Control bits
00= Drive pins P1B and P1D to ‘0’
01= Drive pins P1B and P1D to ‘1’
1x= Pins P1B and P1D tri-state
DS41288C-page 100
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
Note 1: The auto-shutdown condition is a level-
based signal, not an edge-based signal.
As long as the level is present, the auto-
shutdown will persist.
2: Writing to the ECCPASE bit is disabled
while an auto-shutdown condition
persists.
3: Once the auto-shutdown condition has
been removed and the PWM restarted
(either through firmware or auto-restart),
the PWM signal will always restart at the
beginning of the next PWM period.
FIGURE 10-14:
PWM AUTO-SHUTDOWN WITH FIRMWARE RESTART (PRSEN = 0)
PWM Period
Shutdown Event
ECCPASE bit
PWM Activity
Normal PWM
ECCPASE
Cleared by
Firmware
Start of
Shutdown
Shutdown
PWM
PWM Period
Event Occurs Event Clears
Resumes
10.4.5
AUTO-RESTART MODE
The Enhanced PWM can be configured to automati-
cally restart the PWM signal once the auto-shutdown
condition has been removed. Auto-restart is enabled by
setting the PRSEN bit in the PWM1CON register.
If auto-restart is enabled, the ECCPASE bit will remain
set as long as the auto-shutdown condition is active.
When the auto-shutdown condition is removed, the
ECCPASE bit will be cleared via hardware and normal
operation will resume.
FIGURE 10-15:
PWM AUTO-SHUTDOWN WITH AUTO-RESTART ENABLED (PRSEN = 1)
PWM Period
Shutdown Event
ECCPASE bit
PWM Activity
Normal PWM
Start of
Shutdown
Shutdown
PWM
PWM Period
Event Occurs Event Clears
Resumes
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 101
PIC16F610/616/16HV610/616
10.4.6
PROGRAMMABLE DEAD-BAND
DELAY MODE
FIGURE 10-16:
EXAMPLE OF HALF-
BRIDGE PWM OUTPUT
In half-bridge applications where all power switches are
modulated at the PWM frequency, the power switches
normally require more time to turn off than to turn on. If
both the upper and lower power switches are switched
at the same time (one turned on, and the other turned
off), both switches may be on for a short period of time
until one switch completely turns off. During this brief
interval, a very high current (shoot-through current) will
flow through both power switches, shorting the bridge
supply. To avoid this potentially destructive shoot-
through current from flowing during switching, turning
on either of the power switches is normally delayed to
allow the other switch to completely turn off.
Period
Period
Pulse Width
(2)
(2)
P1A
td
td
P1B
(1)
(1)
(1)
td = Dead-Band Delay
Note 1: At this time, the TMR2 register is equal to the
PR2 register.
In Half-Bridge mode, a digitally programmable dead-
band delay is available to avoid shoot-through current
from destroying the bridge power switches. The delay
occurs at the signal transition from the non-active state
to the active state. See Figure 10-16 for illustration.
The lower seven bits of the associated PWM1CON
register (Register 10-3) sets the delay period in terms
of microcontroller instruction cycles (TCY or 4 TOSC).
2: Output signals are shown as active-high.
FIGURE 10-17:
EXAMPLE OF HALF-BRIDGE APPLICATIONS
V+
Standard Half-Bridge Circuit (“Push-Pull”)
FET
Driver
+
V
-
P1A
Load
FET
Driver
+
V
-
P1B
V-
DS41288C-page 102
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
REGISTER 10-3: PWM1CON: ENHANCED PWM CONTROL REGISTER
R/W-0
R/W-0
PDC6
R/W-0
PDC5
R/W-0
PDC4
R/W-0
PDC3
R/W-0
PDC2
R/W-0
PDC1
R/W-0
PDC0
PRSEN
bit 7
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
PRSEN: PWM Restart Enable bit
1= Upon auto-shutdown, the ECCPASE bit clears automatically once the shutdown event goes
away; the PWM restarts automatically
0= Upon auto-shutdown, ECCPASE must be cleared in software to restart the PWM
bit 6-0
PDC<6:0>: PWM Delay Count bits
PDCn = Number of FOSC/4 (4 * TOSC) cycles between the scheduled time when a PWM signal
should transition active and the actual time it transitions active
TABLE 10-7: SUMMARY OF REGISTERS ASSOCIATED WITH PWM
Value on
all other
Resets
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
CCP1CON(1)
CCPR1L(1)
CCPR1H(1)
CM1CON0
CM2CON0
CM2CON1
ECCPAS(1)
INTCON
P1M1
P1M0
DC1B1
DC1B0
CCP1M3
CCP1M2
CCP1M1
CCP1M0
0000 0000
xxxx xxxx
xxxx xxxx
0000 -000
0000 -000
00-0 0010
0000 0000
0000 0000
uuuu uuuu
uuuu uuuu
0000 -000
0000 -000
00-0 0010
0000 0000
Capture/Compare/PWM Register 1 Low Byte
Capture/Compare/PWM Register 1 High Byte
C1ON
C2ON
C1OUT
C2OUT
C1OE
C2OE
—
C1POL
C2POL
T1ACS
—
—
C1R
C2R
C1CH1
C2CH1
T1GSS
PSSBD1
INTF
C1CH0
C2CH0
C2SYNC
PSSBD0
RAIF
MC1OUT
MC2OUT
C1HYS
PSSAC1
RAIE
C2HYS
PSSAC0
T0IF
ECCPASE ECCPAS2 ECCPAS1 ECCPAS0
GIE
PEIE
T0IE
INTE
0000 0000
-000 0-00
-000 0-00
0000 0000
0000 0000
0000 0-00
0000 0-00
0000 0000
-000 0000
0000 0000
--11 1111
--11 1111
PIE1
—
—
ADIE(1)
ADIF(1)
PDC6
CCP1IE(1)
CCP1IF(1)
PDC5
C2IE
C2IF
C1IE
C1IF
—
—
TMR2IE(1)
TMR2IF(1)
PDC1
TMR1IE
TMR1IF
PDC0
PIR1
PWM1CON(1)
T2CON(1)
TMR2(1)
TRISA
PRSEN
—
PDC4
PDC3
PDC2
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000
Timer2 Module Register
0000 0000
--11 1111
--11 1111
—
—
—
—
TRISA5
TRISC5
TRISA4
TRISC4
TRISA3
TRISC3
TRISA2
TRISC2
TRISA1
TRISC1
TRISA0
TRISC0
TRISC
Legend: – = Unimplemented locations, read as ‘0’, u= unchanged, x= unknown. Shaded cells are not used by the Capture, Compare and PWM.
Note 1: PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 103
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 104
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
An external current limiting resistor, RSER, located
between the unregulated supply, VUNREG, and the VDD
pin, drops the difference in voltage between VUNREG
and VDD. RSER must be between RMAX and RMIN as
defined by Equation 11-1.
11.0 VOLTAGE REGULATOR
The PIC16HV616 includes a permanent internal 5 volt
(nominal) shunt regulator in parallel with the VDD pin.
This eliminates the need for an external voltage
regulator in systems sourced by an unregulated supply.
All external devices connected directly to the VDD pin
will share the regulated supply voltage and contribute
to the total VDD supply current (ILOAD).
EQUATION 11-1: RSER LIMITING RESISTOR
(VUMIN - 5V)
RMAX =
1.05 • (4 MA + ILOAD)
11.1 Regulator Operation
A shunt regulator generates a specific supply voltage
by creating a voltage drop across a pass resistor RSER.
The voltage at the VDD pin of the microcontroller is
monitored and compared to an internal voltage refer-
ence. The current through the resistor is then adjusted,
based on the result of the comparison, to produce a
voltage drop equal to the difference between the supply
voltage VUNREG and the VDD of the microcontroller.
See Figure 11-1 for voltage regulator schematic.
(VUMAX - 5V)
RMIN =
0.95 • (50 MA)
Where:
RMAX = maximum value of RSER (ohms)
RMIN = minimum value of RSER (ohms)
VUMIN = minimum value of VUNREG
VUMAX = maximum value of VUNREG
FIGURE 11-1:
VOLTAGE REGULATOR
VDD
= regulated voltage (5V nominal)
VUNREG
ILOAD = maximum expected load current in mA
including I/O pin currents and external
circuits connected to VDD.
ILOAD
RSER
ISUPPLY
1.05 = compensation for +5% tolerance of RSER
0.95 = compensation for -5% tolerance of RSER
VDD
ISHUNT
CBYPASS
Feedback
11.2 Regulator Considerations
VSS
The supply voltage VUNREG and load current are not
constant. Therefore, the current range of the regulator
is limited. Selecting a value for RSER must take these
three factors into consideration.
Since the regulator uses the band gap voltage as the
regulated voltage reference, this voltage reference is
permanently enabled in the PIC16F610/16HV610
devices.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 105
PIC16F610/616/16HV610/616
12.1 Configuration Bits
12.0 SPECIAL FEATURES OF THE
CPU
The Configuration bits can be programmed (read as
‘0’), or left unprogrammed (read as ‘1’) to select various
device configurations as shown in Register 12-1.
These bits are mapped in program memory location
2007h.
The PIC16F610/616/16HV610/616 has a host of
features intended to maximize system reliability,
minimize cost through elimination of external
components, provide power saving features and offer
code protection.
Note:
Address 2007h is beyond the user program
memory space. It belongs to the special
configuration memory space (2000h-
3FFFh), which can be accessed only during
programming. See “PIC12F60X/12F61X/
16F61X Memory Programming Specifica-
tion” (DS41284) for more information.
These features are:
• Reset
- Power-on Reset (POR)
- Power-up Timer (PWRT)
- Oscillator Start-up Timer (OST)
- Brown-out Reset (BOR)
• Interrupts
• Watchdog Timer (WDT)
• Oscillator selection
• Sleep
• Code protection
• ID Locations
• In-Circuit Serial Programming
The PIC16F610/616/16HV610/616 has two timers that
offer necessary delays on power-up. One is the
Oscillator Start-up Timer (OST), intended to keep the
chip in Reset until the crystal oscillator is stable. The
other is the Power-up Timer (PWRT), which provides a
fixed delay of 64 ms (nominal) on power-up only,
designed to keep the part in Reset while the power
supply stabilizes. There is also circuitry to reset the
device if a brown-out occurs, which can use the Power-
up Timer to provide at least a 64 ms Reset. With these
three functions-on-chip, most applications need no
external Reset circuitry.
The Sleep mode is designed to offer a very low-current
Power-Down mode. The user can wake-up from Sleep
through:
• External Reset
• Watchdog Timer Wake-up
• An interrupt
Several oscillator options are also made available to
allow the part to fit the application. The INTOSC option
saves system cost while the LP crystal option saves
power. A set of Configuration bits are used to select
various options (see Register 12-1).
DS41288C-page 106
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
REGISTER 12-1: CONFIG: CONFIGURATION WORD REGISTER
BOREN1(1) BOREN0(1)
bit 8
—
—
—
—
—
—
bit 15
IOSCFS
bit 7
CP(2)
MCLRE(3)
PWRTE
WDTE
FOSC2
FOSC1
FOSC0
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
P = Programmable’
‘0’ = Bit is cleared
U = Unimplemented bit,
read as ‘0’
-n = Value at POR
x = Bit is unknown
bit 15-10
bit 9-8
Unimplemented: Read as ‘1’
BOREN<1:0>: Brown-out Reset Selection bits(1)
11= BOR enabled
10= BOR enabled during operation and disabled in Sleep
0x= BOR disabled
bit 7
IOSCFS: Internal Oscillator Frequency Select bit
1= 8 MHz
0= 4 MHz
bit 6
bit 5
bit 4
bit 3
bit 2-0
CP: Code Protection bit(2)
1= Program memory code protection is disabled
0= Program memory code protection is enabled
MCLRE: MCLR Pin Function Select bit(3)
1= MCLR pin function is MCLR
0= MCLR pin function is digital input, MCLR internally tied to VDD
PWRTE: Power-up Timer Enable bit
1= PWRT disabled
0= PWRT enabled
WDTE: Watchdog Timer Enable bit
1= WDT enabled
0= WDT disabled
FOSC<2:0>: Oscillator Selection bits
111= RC oscillator: CLKOUT function on RA4/OSC2/CLKOUT pin, RC on RA5/OSC1/CLKIN
110= RCIO oscillator: I/O function on RA4/OSC2/CLKOUT pin, RC on RA5/OSC1/CLKIN
101= INTOSC oscillator: CLKOUT function on RA4/OSC2/CLKOUT pin, I/O function on
RA5/OSC1/CLKIN
100= INTOSCIO oscillator: I/O function on RA4/OSC2/CLKOUT pin, I/O function on
RA5/OSC1/CLKIN
011= EC: I/O function on RA4/OSC2/CLKOUT pin, CLKIN on RA5/OSC1/CLKIN
010= HS oscillator: High-speed crystal/resonator on RA4/OSC2/CLKOUT and RA5/OSC1/CLKIN
001= XT oscillator: Crystal/resonator on RA4/OSC2/CLKOUT and RA5/OSC1/CLKIN
000= LP oscillator: Low-power crystal on RA4/OSC2/CLKOUT and RA5/OSC1/CLKIN
Note 1: Enabling Brown-out Reset does not automatically enable Power-up Timer.
2: The entire program memory will be erased when the code protection is turned off.
3: When MCLR is asserted in INTOSC or RC mode, the internal clock oscillator is disabled.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 107
PIC16F610/616/16HV610/616
Some registers are not affected in any Reset condition;
12.2 Calibration Bits
their status is unknown on POR and unchanged in any
other Reset. Most other registers are reset to a “Reset
state” on:
The 8 MHz internal oscillator is factory calibrated.
These calibration values are stored in fuses located in
the Calibration Word (2009h). The Calibration Word is
not erased when using the specified bulk erase
sequence in the “PIC12F60X/12F61X/16F61X Memory
Programming Specification” (DS41284) and thus, does
not require reprogramming.
• Power-on Reset
• MCLR Reset
• MCLR Reset during Sleep
• WDT Reset
• Brown-out Reset (BOR)
12.3 Reset
WDT wake-up does not cause register resets in the
same manner as a WDT Reset since wake-up is
viewed as the resumption of normal operation. TO and
PD bits are set or cleared differently in different Reset
situations, as indicated in Table 12-2. Software can use
these bits to determine the nature of the Reset. See
Table 12-4 for a full description of Reset states of all
registers.
The
PIC16F610/616/16HV610/616
differentiates
between various kinds of Reset:
a) Power-on Reset (POR)
b) WDT Reset during normal operation
c) WDT Reset during Sleep
d) MCLR Reset during normal operation
e) MCLR Reset during Sleep
f) Brown-out Reset (BOR)
A simplified block diagram of the On-Chip Reset Circuit
is shown in Figure 12-1.
The MCLR Reset path has a noise filter to detect and
ignore small pulses. See Section 15.0 “Electrical
Specifications” for pulse-width specifications.
FIGURE 12-1:
SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
External
Reset
MCLR/VPP pin
Sleep
WDT
WDT
Module
Time-out
Reset
POR
Detect
Power-on Reset
VDD
Brown-out(1)
Reset
BOREN
S
R
OST/PWRT
OST
10-bit Ripple Counter
Chip_Reset
Q
OSC1/
CLKI pin
PWRT
11-bit Ripple Counter
On-Chip
RC OSC
Enable PWRT
Enable OST
Note 1: Refer to the Configuration Word register (Register 12-1).
DS41288C-page 108
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
12.3.1
POWER-ON RESET (POR)
FIGURE 12-2:
RECOMMENDED MCLR
CIRCUIT
The on-chip POR circuit holds the chip in Reset until
VDD has reached a high enough level for proper
operation. To take advantage of the POR, simply
connect the MCLR pin through a resistor to VDD. This
will eliminate external RC components usually needed
to create Power-on Reset. A maximum rise time for
VDD is required. See Section 15.0 “Electrical
Specifications” for details. If the BOR is enabled, the
maximum rise time specification does not apply. The
BOR circuitry will keep the device in Reset until VDD
reaches VBOR (see Section 12.3.4 “Brown-out Reset
(BOR)”).
VDD
PIC® MCU
R1
1 kΩ (or greater)
R2
MCLR
100 Ω
(needed with capacitor)
SW1
(optional)
C1
0.1 μF
(optional, not critical)
Note:
The POR circuit does not produce an
internal Reset when VDD declines. To re-
enable the POR, VDD must reach Vss for
a minimum of 100 μs.
When the device starts normal operation (exits the
Reset condition), device operating parameters (i.e.,
voltage, frequency, temperature, etc.) must be met to
ensure proper operation. If these conditions are not
met, the device must be held in Reset until the
operating conditions are met.
12.3.3
POWER-UP TIMER (PWRT)
The Power-up Timer provides a fixed 64 ms (nominal)
time-out on power-up only, from POR or Brown-out
Reset. The Power-up Timer operates from an internal
RC oscillator. For more information, see Section 3.4
“Internal Clock Modes”. The chip is kept in Reset as
long as PWRT is active. The PWRT delay allows the
VDD to rise to an acceptable level. A Configuration bit,
PWRTE, can disable (if set) or enable (if cleared or
programmed) the Power-up Timer. The Power-up
Timer should be enabled when Brown-out Reset is
enabled, although it is not required.
For additional information, refer to Application Note
AN607, “Power-up Trouble Shooting” (DS00607).
12.3.2
MCLR
PIC16F610/616/16HV610/616 has a noise filter in the
MCLR Reset path. The filter will detect and ignore
small pulses.
The Power-up Timer delay will vary from chip-to-chip
due to:
It should be noted that a WDT Reset does not drive
MCLR pin low.
• VDD variation
Voltages applied to the MCLR pin that exceed its
specification can result in both MCLR Resets and
excessive current beyond the device specification
during the ESD event. For this reason, Microchip
recommends that the MCLR pin no longer be tied
directly to VDD. The use of an RC network, as shown in
Figure 12-2, is suggested.
• Temperature variation
• Process variation
See DC parameters for details (Section 15.0
“Electrical Specifications”).
An internal MCLR option is enabled by clearing the
MCLRE bit in the Configuration Word register. When
MCLRE = 0, the Reset signal to the chip is generated
internally. When the MCLRE = 1, the RA3/MCLR pin
becomes an external Reset input. In this mode, the
RA3/MCLR pin has a weak pull-up to VDD.
Note:
Voltage spikes below VSS at the MCLR
pin, inducing currents greater than 80 mA,
may cause latch-up. Thus, a series resis-
tor of 50-100 Ω should be used when
applying a “low” level to the MCLR pin,
rather than pulling this pin directly to VSS.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 109
PIC16F610/616/16HV610/616
On any Reset (Power-on, Brown-out Reset, Watchdog
timer, etc.), the chip will remain in Reset until VDD rises
above VBOR (see Figure 12-3). If enabled, the Power-
up Timer will be invoked by the Reset and keep the chip
in Reset an additional 64 ms.
12.3.4
BROWN-OUT RESET (BOR)
The BOREN0 and BOREN1 bits in the Configuration
Word register select one of three BOR modes.
Selecting BOREN<1:0> = 10, the BOR is automatically
disabled in Sleep to conserve power and enabled on
wake-up. See Register 12-1 for the Configuration Word
definition.
Note:
The Power-up Timer is enabled by the
PWRTE bit in the Configuration Word
register.
A brown-out occurs when VDD falls below VBOR for
greater than parameter TBOR (see Section 15.0
“Electrical Specifications”). The brown-out condition
will reset the device. This will occur regardless of VDD
slew rate. A Brown-out Reset may not occur if VDD falls
below VBOR for less than parameter TBOR.
If VDD drops below VBOR while the Power-up Timer is
running, the chip will go back into a Brown-out Reset
and the Power-up Timer will be re-initialized. Once VDD
rises above VBOR, the Power-up Timer will execute a
64 ms Reset.
FIGURE 12-3:
BROWN-OUT SITUATIONS
VDD
VBOR
Internal
Reset
(1)
64 ms
VDD
VBOR
Internal
Reset
< 64 ms
(1)
64 ms
VDD
VBOR
Internal
Reset
(1)
64 ms
Note 1: 64 ms delay only if PWRTE bit is programmed to ‘0’.
DS41288C-page 110
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
12.3.5
TIME-OUT SEQUENCE
12.3.6
POWER CONTROL (PCON)
REGISTER
On power-up, the time-out sequence is as follows:
• PWRT time-out is invoked after POR has expired.
The Power Control register PCON (address 8Eh) has
two Status bits to indicate what type of Reset occurred
last.
• OST is activated after the PWRT time-out has
expired.
Bit 0 is BOR (Brown-out). BOR is unknown on Power-
on Reset. It must then be set by the user and checked
on subsequent Resets to see if BOR = 0, indicating that
a Brown-out has occurred. The BOR Status bit is a
“don’t care” and is not necessarily predictable if the
brown-out circuit is disabled (BOREN<1:0> = 00in the
Configuration Word register).
The total time-out will vary based on oscillator
configuration and PWRTE bit status. For example, in EC
mode with PWRTE bit erased (PWRT disabled), there
will be no time-out at all. Figure 12-4, Figure 12-5 and
Figure 12-6 depict time-out sequences.
Since the time-outs occur from the POR pulse, if MCLR
is kept low long enough, the time-outs will expire. Then,
bringing MCLR high will begin execution immediately
(see Figure 12-5). This is useful for testing purposes or
to synchronize more than one PIC16F610/616/
16HV610/616 device operating in parallel.
Bit 1 is POR (Power-on Reset). It is a ‘0’ on Power-on
Reset and unaffected otherwise. The user must write a
‘1’ to this bit following a Power-on Reset. On a subse-
quent Reset, if POR is ‘0’, it will indicate that a Power-
on Reset has occurred (i.e., VDD may have gone too
low).
Table 12-5 shows the Reset conditions for some
special registers, while Table 12-4 shows the Reset
conditions for all the registers.
For more information, see Section 12.3.4 “Brown-out
Reset (BOR)”.
TABLE 12-1: TIME-OUT IN VARIOUS SITUATIONS
Power-up
Brown-out Reset
Wake-up from
Oscillator Configuration
Sleep
PWRTE = 0
PWRTE = 1
PWRTE = 0
PWRTE = 1
XT, HS, LP
TPWRT + 1024 •
TOSC
1024 • TOSC
TPWRT + 1024 •
TOSC
1024 • TOSC
1024 • TOSC
—
RC, EC, INTOSC
TPWRT
—
TPWRT
—
TABLE 12-2: STATUS/PCON BITS AND THEIR SIGNIFICANCE
POR
BOR
TO
PD
Condition
0
u
u
u
x
0
u
u
1
1
0
0
1
1
u
0
Power-on Reset
Brown-out Reset
WDT Reset
WDT Wake-up
u
u
u
u
u
1
u
0
MCLR Reset during normal operation
MCLR Reset during Sleep
Legend: u= unchanged, x= unknown
TABLE 12-3: SUMMARY OF REGISTERS ASSOCIATED WITH BROWN-OUT RESET
Value on
Value on
all other
Resets(1)
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
POR, BOR
PCON
—
—
—
—
—
—
Z
POR
DC
BOR ---- --qq ---- --uu
0001 1xxx 000q quuu
STATUS
IRP
RP1
RP0
TO
PD
C
Legend: u= unchanged, x= unknown, – = unimplemented bit, reads as ‘0’, q= value depends on condition.
Shaded cells are not used by BOR.
Note 1: Other (non Power-up) Resets include MCLR Reset and Watchdog Timer Reset during normal operation.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 111
PIC16F610/616/16HV610/616
FIGURE 12-4:
TIME-OUT SEQUENCE ON POWER-UP (DELAYED MCLR): CASE 1
VDD
MCLR
Internal POR
TPWRT
PWRT Time-out
OST Time-out
Internal Reset
TOST
FIGURE 12-5:
TIME-OUT SEQUENCE ON POWER-UP (DELAYED MCLR): CASE 2
VDD
MCLR
Internal POR
TPWRT
PWRT Time-out
OST Time-out
Internal Reset
TOST
FIGURE 12-6:
TIME-OUT SEQUENCE ON POWER-UP (MCLR WITH VDD)
VDD
MCLR
Internal POR
TPWRT
PWRT Time-out
OST Time-out
Internal Reset
TOST
DS41288C-page 112
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 12-4: INITIALIZATION CONDITION FOR REGISTERS
Wake-up from Sleep through
Interrupt
Wake-up from Sleep through
WDT Time-out
MCLR Reset
WDT Reset
Power-on
Reset
Register
Address
Brown-out Reset(1)
W
—
00h/80h
01h
xxxx xxxx
xxxx xxxx
xxxx xxxx
0000 0000
0001 1xxx
xxxx xxxx
--x0 x000
--xx xx00
---0 0000
0000 0000
-000 0-00
xxxx xxxx
xxxx xxxx
0000 0000
0000 0000
-000 0000
xxxx xxxx
xxxx xxxx
0000 0000
0000 0000
0000 0000
0000 0000
0000 -000
0000 -000
00-0 0000
xxxx xxxx
0000 0000
1111 1111
--11 1111
--11 1111
-000 0-00
---- --0x
---0 0000
uuuu uuuu
xxxx xxxx
uuuu uuuu
0000 0000
000q quuu(4)
uuuu uuuu
--u0 u000
--uu 00uu
---0 0000
0000 0000
-000 0-00
uuuu uuuu
uuuu uuuu
uuuu uuuu
0000 0000
-000 0000
uuuu uuuu
uuuu uuuu
0000 0000
0000 0000
0000 0000
0000 0000
0000 -000
0000 -000
00-0 0000
uuuu uuuu
0000 0000
1111 1111
--11 1111
--11 1111
-000 0-00
---- --uu(1, 5)
---u uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
PC + 1(3)
INDF
TMR0
PCL
02h/82h
03h/83h
04h/84h
05h
STATUS
FSR
uuuq quuu(4)
uuuu uuuu
--uu uuuu
--uu uuuu
---u uuuu
uuuu uuuu(2)
-uuu u-uu(2)
uuuu uuuu
uuuu uuuu
-uuu uuuu
uuuu uuuu
-uuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu -uuu
uuuu -uuu
uu-u uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
--uu uuuu
--uu uuuu
-uuu u-uu
---- --uu
---u uuuu
PORTA
PORTC
07h
PCLATH
INTCON
PIR1
0Ah/8Ah
0Bh/8Bh
0Ch
TMR1L
0Eh
TMR1H
0Fh
T1CON
10h
TMR2(6)
T2CON(6)
CCPR1L(6)
CCPR1H(6)
CCP1CON(6)
PWM1CON(6)
ECCPAS(6)
VRCON
CM1CON0
CM2CON0
CM2CON1
ADRESH(6)
ADCON0(6)
OPTION_REG
TRISA
11h
12h
13h
14h
15h
16h
17h
19h
1Ah
1Bh
1Ch
1Eh
1Fh
81h
85h
TRISC
87h
PIE1
8Ch
PCON
8Eh
OSCTUNE
90h
Legend: u= unchanged, x= unknown, – = unimplemented bit, reads as ‘0’, q= value depends on condition.
Note 1: If VDD goes too low, Power-on Reset will be activated and registers will be affected differently.
2: One or more bits in INTCON and/or PIR1 will be affected (to cause wake-up).
3: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt
vector (0004h).
4: See Table 12-5 for Reset value for specific condition.
5: If Reset was due to brown-out, then bit 0 = 0. All other Resets will cause bit 0 = u.
6: PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 113
PIC16F610/616/16HV610/616
TABLE 12-4: INITIALIZATION CONDITION FOR REGISTERS (CONTINUED)
Wake-up from Sleep through
MCLR Reset
Power-on
Reset
Interrupt
Wake-up from Sleep through
WDT Time-out (Continued)
Register
Address
WDT Reset (Continued)
Brown-out Reset(1)
ANSEL
PR2(6)
91h
92h
95h
96h
99h
9Ah
9Eh
9Fh
1111 1111
1111 1111
--11 -111
--00 0000
0000 00-0
00-- ----
xxxx xxxx
-000 ----
1111 1111
1111 1111
--11 -111
--00 0000
0000 00-0
00-- ----
uuuu uuuu
-000 ----
uuuu uuuu
1111 1111
--uu -uuu
--uu uuuu
uuuu uu-u
uu-- ----
uuuu uuuu
-uuu ----
WPUA
IOCA
SRCON0
SRCON1
ADRESL(6)
ADCON1(6)
Legend: u= unchanged, x= unknown, – = unimplemented bit, reads as ‘0’, q= value depends on condition.
Note 1: If VDD goes too low, Power-on Reset will be activated and registers will be affected differently.
2: One or more bits in INTCON and/or PIR1 will be affected (to cause wake-up).
3: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt
vector (0004h).
4: See Table 12-5 for Reset value for specific condition.
5: If Reset was due to brown-out, then bit 0 = 0. All other Resets will cause bit 0 = u.
6: PIC16F616/16HV616 only.
TABLE 12-5: INITIALIZATION CONDITION FOR SPECIAL REGISTERS
Program
Counter
Status
Register
PCON
Register
Condition
Power-on Reset
000h
000h
0001 1xxx
000u uuuu
---- --0x
---- --uu
MCLR Reset during normal operation
---- --uu
MCLR Reset during Sleep
WDT Reset
000h
000h
0001 0uuu
0000 uuuu
uuu0 0uuu
0001 1uuu
uuu1 0uuu
---- --uu
---- --uu
---- --10
---- --uu
WDT Wake-up
PC + 1
000h
PC + 1(1)
Brown-out Reset
Interrupt Wake-up from Sleep
Legend: u= unchanged, x= unknown, – = unimplemented bit, reads as ‘0’.
Note 1: When the wake-up is due to an interrupt and Global Interrupt Enable bit, GIE, is set, the PC is loaded with
the interrupt vector (0004h) after execution of PC + 1.
DS41288C-page 114
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
For external interrupt events, such as the INT pin or
PORTA change interrupt, the interrupt latency will be
12.4 Interrupts
The PIC16F610/616/16HV610/616 has multiple
sources of interrupt:
three or four instruction cycles. The exact latency
depends upon when the interrupt event occurs (see
Figure 12-8). The latency is the same for one or two-
cycle instructions. Once in the Interrupt Service
Routine, the source(s) of the interrupt can be
determined by polling the interrupt flag bits. The
interrupt flag bit(s) must be cleared in software before
re-enabling interrupts to avoid multiple interrupt
requests.
• External Interrupt RA2/INT
• Timer0 Overflow Interrupt
• PORTA Change Interrupts
• 2 Comparator Interrupts
• A/D Interrupt (PIC16F616/16HV616 only)
• Timer1 Overflow Interrupt
• Timer2 Match Interrupt (PIC16F616/16HV616 only)
Note 1: Individual interrupt flag bits are set,
regardless of the status of their
corresponding mask bit or the GIE bit.
• Enhanced CCP Interrupt (PIC16F616/16HV616
only)
The Interrupt Control register (INTCON) and Peripheral
Interrupt Request Register 1 (PIR1) record individual
interrupt requests in flag bits. The INTCON register
also has individual and global interrupt enable bits.
2: When an instruction that clears the GIE
bit is executed, any interrupts that were
pending for execution in the next cycle
are ignored. The interrupts, which were
ignored, are still pending to be serviced
when the GIE bit is set again.
The Global Interrupt Enable bit, GIE of the INTCON
register, enables (if set) all unmasked interrupts, or
disables (if cleared) all interrupts. Individual interrupts
can be disabled through their corresponding enable
bits in the INTCON register and PIE1 register. GIE is
cleared on Reset.
For additional information on Timer1, Timer2,
comparators, ADC, Enhanced CCP modules, refer to
the respective peripheral section.
12.4.1
RA2/INT INTERRUPT
When an interrupt is serviced, the following actions
occur automatically:
The external interrupt on the RA2/INT pin is edge-
triggered; either on the rising edge if the INTEDG bit of
the OPTION register is set, or the falling edge, if the
INTEDG bit is clear. When a valid edge appears on the
RA2/INT pin, the INTF bit of the INTCON register is set.
This interrupt can be disabled by clearing the INTE
control bit of the INTCON register. The INTF bit must
be cleared by software in the Interrupt Service Routine
before re-enabling this interrupt. The RA2/INT interrupt
can wake-up the processor from Sleep, if the INTE bit
was set prior to going into Sleep. See Section 12.7
“Power-Down Mode (Sleep)” for details on Sleep and
Figure 12-9 for timing of wake-up from Sleep through
RA2/INT interrupt.
• The GIE is cleared to disable any further interrupt.
• The return address is pushed onto the stack.
• The PC is loaded with 0004h.
The Return from Interrupt instruction, RETFIE, exits
the interrupt routine, as well as sets the GIE bit, which
re-enables unmasked interrupts.
The following interrupt flags are contained in the
INTCON register:
• INT Pin Interrupt
• PORTA Change Interrupt
• Timer0 Overflow Interrupt
The peripheral interrupt flags are contained in the
special register, PIR1. The corresponding interrupt
enable bit is contained in special register, PIE1.
Note:
The ANSEL register must be initialized to
configure an analog channel as a digital
input. Pins configured as analog inputs will
read ‘0’ and cannot generate an interrupt.
The following interrupt flags are contained in the PIR1
register:
• A/D Interrupt
• 2 Comparator Interrupts
• Timer1 Overflow Interrupt
• Timer2 Match Interrupt
• Enhanced CCP Interrupt
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 115
PIC16F610/616/16HV610/616
12.4.2
TIMER0 INTERRUPT
12.4.3
PORTA INTERRUPT-ON-CHANGE
An overflow (FFh → 00h) in the TMR0 register will set
the T0IF bit of the INTCON register. The interrupt can
be enabled/disabled by setting/clearing T0IE bit of the
INTCON register. See Section 5.0 “Timer0 Module”
for operation of the Timer0 module.
An input change on PORTA sets the RAIF bit of the
INTCON register. The interrupt can be enabled/
disabled by setting/clearing the RAIE bit of the INTCON
register. Plus, individual pins can be configured through
the IOCA register.
Note:
If a change on the I/O pin should occur
when any PORTA operation is being
executed, then the RAIF interrupt flag may
not get set.
FIGURE 12-7:
INTERRUPT LOGIC
IOC-RA0
IOCA0
IOC-RA1
IOCA1
IOC-RA2
IOCA2
IOC-RA3
IOCA3
IOC-RA4
IOCA4
IOC-RA5
IOCA5
T0IF
T0IE
(1)
Wake-up (If in Sleep mode)
(2)
TMR2IF
(2)
INTF
INTE
TMR2IE
Interrupt to CPU
RAIF
RAIE
TMR1IF
TMR1IE
C1IF
C1IE
PEIE
GIE
C2IF
C2IE
(2)
ADIF
(2)
ADIE
(2)
CCP1IF
(2)
CCP1IE
Note 1: Some peripherals depend upon the system clock for
operation. Since the system clock is suspended during Sleep, only
those peripherals which do not depend upon the system clock will wake
the part from Sleep. See Section 12.7.1 “Wake-up from Sleep”.
2: PIC16F616/16HV616 only.
DS41288C-page 116
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
FIGURE 12-8:
INT PIN INTERRUPT TIMING
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
(3)
CLKOUT
(4)
INT pin
(1)
(1)
(2)
(5)
Interrupt Latency
INTF flag
(INTCON reg.)
GIE bit
(INTCON reg.)
INSTRUCTION FLOW
PC
PC + 1
—
0004h
0005h
PC
Inst (PC)
PC + 1
Instruction
Fetched
Inst (PC + 1)
Inst (0004h)
Inst (0005h)
Inst (0004h)
Instruction
Executed
Dummy Cycle
Dummy Cycle
Inst (PC)
Inst (PC – 1)
Note 1: INTF flag is sampled here (every Q1).
2: Asynchronous interrupt latency = 3-4 TCY. Synchronous latency = 3 TCY, where TCY = instruction cycle time. Latency
is the same whether Inst (PC) is a single cycle or a 2-cycle instruction.
3: CLKOUT is available only in INTOSC and RC Oscillator modes.
4: For minimum width of INT pulse, refer to AC specifications in Section 15.0 “Electrical Specifications”.
5: INTF is enabled to be set any time during the Q4-Q1 cycles.
TABLE 12-6: SUMMARY OF REGISTERS ASSOCIATED WITH INTERRUPTS
Value on
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
all other
Resets
INTCON
IOCA
GIE
—
PEIE
—
ADIF(1)
ADIE(1)
T0IE
INTE
IOCA4
C2IF
RAIE
IOCA3
C1IF
T0IF
IOCA2
—
INTF
RAIF
0000 0000
--00 0000
-000 0-00
-000 0-00
0000 0000
--00 0000
-000 0-00
-000 0-00
IOCA5
IOCA1
IOCA0
PIR1
—
CCP1IF(1)
CCP1IE(1)
TMR2IF(1)
TMR2IE(1)
TMR1IF
TMR1IE
PIE1
—
C2IE
C1IE
—
Legend:
x= unknown, u= unchanged, – = unimplemented read as ‘0’, q= value depends upon condition.
Shaded cells are not used by the interrupt module.
Note 1:
PIC16F616/16HV616 only.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 117
PIC16F610/616/16HV610/616
12.5 Context Saving During Interrupts
During an interrupt, only the return PC value is saved
on the stack. Typically, users may wish to save key
registers during an interrupt (e.g., W and STATUS
registers). This must be implemented in software.
Temporary
holding
registers
W_TEMP
and
STATUS_TEMP should be placed in the last 16 bytes
of GPR (see Figure 2-4). These 16 locations are
common to all banks and do not require banking. This
makes context save and restore operations simpler.
The code shown in Example 12-1 can be used to:
• Store the W register
• Store the STATUS register
• Execute the ISR code
• Restore the Status (and Bank Select Bit register)
• Restore the W register
Note:
The PIC16F610/616/16HV610/616 does
not require saving the PCLATH. However,
if computed GOTO’s are used in both the
ISR and the main code, the PCLATH must
be saved and restored in the ISR.
EXAMPLE 12-1:
SAVING STATUS AND W REGISTERS IN RAM
MOVWF
SWAPF
W_TEMP
STATUS,W
;Copy W to TEMP register
;Swap status to be saved into W
;Swaps are used because they do not affect the status bits
;Save status to bank zero STATUS_TEMP register
MOVWF
:
STATUS_TEMP
:(ISR)
:
;Insert user code here
SWAPF
STATUS_TEMP,W
;Swap STATUS_TEMP register into W
;(sets bank to original state)
;Move W into STATUS register
;Swap W_TEMP
MOVWF
SWAPF
SWAPF
STATUS
W_TEMP,F
W_TEMP,W
;Swap W_TEMP into W
DS41288C-page 118
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
12.6.1
WDT PERIOD
12.6 Watchdog Timer (WDT)
The WDT has a nominal time-out period of 18 ms (with
no prescaler). The time-out periods vary with
temperature, VDD and process variations from part to
part (see Table 15-4, Parameter 31). If longer time-out
periods are desired, a prescaler with a division ratio of
up to 1:128 can be assigned to the WDT under
software control by writing to the OPTION register.
Thus, time-out periods up to 2.3 seconds can be
realized.
The Watchdog Timer is a free running, on-chip RC
oscillator, which requires no external components. This
RC oscillator is separate from the external RC oscillator
of the CLKIN pin and INTOSC. That means that the
WDT will run, even if the clock on the OSC1 and OSC2
pins of the device has been stopped (for example, by
execution of a SLEEPinstruction). During normal oper-
ation, a WDT time out generates a device Reset. If the
device is in Sleep mode, a WDT time out causes the
device to wake-up and continue with normal operation.
The WDT can be permanently disabled by program-
ming the Configuration bit, WDTE, as clear
(Section 12.1 “Configuration Bits”).
The CLRWDT and SLEEP instructions clear the WDT
and the prescaler, if assigned to the WDT, and prevent
it from timing out and generating a device Reset.
The TO bit in the STATUS register will be cleared upon
a Watchdog Timer time out.
12.6.2
WDT PROGRAMMING
CONSIDERATIONS
It should also be taken in account that under worst-
case conditions (i.e., VDD = Min., Temperature = Max.,
Max. WDT prescaler) it may take several seconds
before a WDT time out occurs.
FIGURE 12-2:
WATCHDOG TIMER BLOCK DIAGRAM
CLKOUT
(= FOSC/4)
Data Bus
0
1
8
1
SYNC 2
Cycles
TMR0
T0CKI
pin
0
0
1
Set Flag bit T0IF
on Overflow
T0CS
T0SE
8-bit
Prescaler
PSA
8
PSA
3
1
PS<2:0>
WDT
Time-Out
Watchdog
Timer
0
PSA
WDTE
Note 1: T0SE, T0CS, PSA, PS<2:0> are bits in the OPTION register.
TABLE 12-7: WDT STATUS
Conditions
WDT
WDTE = 0
CLRWDTCommand
Cleared
Exit Sleep + System Clock = EXTRC, INTRC, EC
Exit Sleep + System Clock = XT, HS, LP
Cleared until the end of OST
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 119
PIC16F610/616/16HV610/616
TABLE 12-8: SUMMARY OF REGISTERS ASSOCIATED WITH WATCHDOG TIMER
Value on
all other
Resets
Value on
POR, BOR
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
OPTION_REG RAPU INTEDG T0CS
T0SE
PSA
PS2
PS1
PS0
1111 1111 1111 1111
(1)
CONFIG
IOSCFS
CP
MCLRE PWRTE WDTE
FOSC2 FOSC1
FOSC0
—
—
Legend:
Shaded cells are not used by the Watchdog Timer.
Note 1: See Register 12-1 for operation of all Configuration Word register bits.
DS41288C-page 120
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
When the SLEEPinstruction is being executed, the next
instruction (PC + 1) is prefetched. For the device to
12.7 Power-Down Mode (Sleep)
The Power-Down mode is entered by executing a
SLEEPinstruction.
wake-up through an interrupt event, the corresponding
interrupt enable bit must be set (enabled). Wake-up is
regardless of the state of the GIE bit. If the GIE bit is
clear (disabled), the device continues execution at the
instruction after the SLEEPinstruction. If the GIE bit is
set (enabled), the device executes the instruction after
the SLEEP instruction, then branches to the interrupt
address (0004h). In cases where the execution of the
instruction following SLEEP is not desirable, the user
should have a NOPafter the SLEEPinstruction.
If the Watchdog Timer is enabled:
• WDT will be cleared but keeps running.
• PD bit in the STATUS register is cleared.
• TO bit is set.
• Oscillator driver is turned off.
• I/O ports maintain the status they had before SLEEP
was executed (driving high, low or high-impedance).
Note:
If the global interrupts are disabled (GIE is
cleared) and any interrupt source has both
its interrupt enable bit and the correspond-
ing interrupt flag bits set, the device will
immediately wake-up from Sleep.
For lowest current consumption in this mode, all I/O pins
should be either at VDD or VSS, with no external circuitry
drawing current from the I/O pin and the comparators
and CVREF should be disabled. I/O pins that are high-
impedance inputs should be pulled high or low externally
to avoid switching currents caused by floating inputs.
The T0CKI input should also be at VDD or VSS for lowest
current consumption. The contribution from on-chip pull-
ups on PORTA should be considered.
The WDT is cleared when the device wakes up from
Sleep, regardless of the source of wake-up.
12.7.2
WAKE-UP USING INTERRUPTS
The MCLR pin must be at a logic high level.
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
Note:
It should be noted that a Reset generated
by a WDT time-out does not drive MCLR
pin low.
• If the interrupt occurs before the execution of a
SLEEPinstruction, the SLEEPinstruction will
complete as a NOP. Therefore, the WDT and WDT
prescaler and postscaler (if enabled) will not be
cleared, the TO bit will not be set and the PD bit
will not be cleared.
12.7.1
WAKE-UP FROM SLEEP
The device can wake-up from Sleep through one of the
following events:
1. External Reset input on MCLR pin.
• If the interrupt occurs during or after the
execution of a SLEEPinstruction, the device will
Immediately wake-up from Sleep. The SLEEP
instruction is executed. Therefore, the WDT and
WDT prescaler and postscaler (if enabled) will be
cleared, the TO bit will be set and the PD bit will
be cleared.
2. Watchdog Timer wake-up (if WDT was
enabled).
3. Interrupt from RA2/INT pin, PORTA change or a
peripheral interrupt.
The first event will cause a device Reset. The two latter
events are considered a continuation of program
execution. The TO and PD bits in the STATUS register
can be used to determine the cause of device Reset.
The PD bit, which is set on power-up, is cleared when
Sleep is invoked. TO bit is cleared if WDT wake-up
occurred.
Even if the flag bits were checked before executing a
SLEEP instruction, it may be possible for flag bits to
become set before the SLEEPinstruction completes. To
determine whether a SLEEPinstruction executed, test
the PD bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
The following peripheral interrupts can wake the device
from Sleep:
To ensure that the WDT is cleared, a CLRWDTinstruction
should be executed before a SLEEP instruction. See
Figure 12-9 for more details.
1. Timer1 interrupt. Timer1 must be operating as
an asynchronous counter.
2. ECCP Capture mode interrupt.
3. A/D conversion (when A/D clock source is RC).
4. Comparator output changes state.
5. Interrupt-on-change.
6. External Interrupt from INT pin.
Other peripherals cannot generate interrupts since
during Sleep, no on-chip clocks are present.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 121
PIC16F610/616/16HV610/616
FIGURE 12-9:
WAKE-UP FROM SLEEP THROUGH INTERRUPT
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
CLKOUT(4)
INT pin
(2)
TOST
INTF flag
(INTCON reg.)
Interrupt Latency(3)
GIE bit
(INTCON reg.)
Processor in
Sleep
Instruction Flow
PC
PC
PC + 1
PC + 2
PC + 2
PC + 2
0004h
0005h
Instruction
Fetched
Inst(0004h)
Inst(PC + 1)
Inst(PC + 2)
Inst(0005h)
Inst(PC) = Sleep
Instruction
Executed
Dummy Cycle
Dummy Cycle
Sleep
Inst(PC + 1)
Inst(PC – 1)
Inst(0004h)
Note 1: XT, HS or LP Oscillator mode assumed.
2: TOST = 1024 TOSC (drawing not to scale). This delay does not apply to EC, INTOSC and RC Oscillator modes.
3: GIE = ‘1’ assumed. In this case after wake-up, the processor jumps to 0004h. If GIE = ‘0’, execution will continue in-line.
4: CLKOUT is not available in XT, HS, LP or EC Oscillator modes, but shown here for timing reference.
12.8 Code Protection
If the code protection bit(s) have not been
programmed, the on-chip program memory can be
read out using ICSP™ for verification purposes.
Note:
The entire Flash program memory will be
erased when the code protection is turned
off. See the “PIC12F60X/12F61X/16F61X
Memory Programming Specification”
(DS41284) for more information.
12.9 ID Locations
Four memory locations (2000h-2003h) are designated
as ID locations where the user can store checksum or
other code identification numbers. These locations are
not accessible during normal execution but are
readable and writable during Program/Verify mode.
Only the Least Significant 7 bits of the ID locations are
used.
DS41288C-page 122
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
12.10 In-Circuit Serial Programming™
12.11 In-Circuit Debugger
The PIC16F610/616/16HV610/616 microcontrollers
can be serially programmed while in the end
application circuit. This is simply done with five
connections for:
Since in-circuit debugging requires access to three
pins, MPLAB® ICD 2 development with an 14-pin
device is not practical. A special 28-pin PIC16F610/
616/16HV610/616 ICD device is used with MPLAB ICD
2 to provide separate clock, data and MCLR pins and
frees all normally available pins to the user.
• clock
• data
A special debugging adapter allows the ICD device to
be used in place of a PIC16F610/616/16HV610/616
device. The debugging adapter is the only source of the
ICD device.
• power
• ground
• programming voltage
This allows customers to manufacture boards with
unprogrammed devices and then program the micro-
controller just before shipping the product. This also
allows the most recent firmware or a custom firmware
to be programmed.
When the ICD pin on the PIC16F610/616/16HV610/
616 ICD device is held low, the In-Circuit Debugger
functionality is enabled. This function allows simple
debugging functions when used with MPLAB ICD 2.
When the microcontroller has this feature enabled,
some of the resources are not available for general
use. Table 12-9 shows which features are consumed
by the background debugger.
The device is placed into a Program/Verify mode by
holding the RA0 and RA1 pins low, while raising the
MCLR (VPP) pin from VIL to VIHH. See the “PIC12F60X/
12F61X/16F61X Memory Programming Specification”
(DS41284) for more information. RA0 becomes the
programming data and RA1 becomes the programming
clock. Both RA0 and RA1 are Schmitt Trigger inputs in
Program/Verify mode.
TABLE 12-9: DEBUGGER RESOURCES
Resource
Description
I/O pins
Stack
ICDCLK, ICDDATA
1 level
A typical In-Circuit Serial Programming connection is
shown in Figure 12-10.
Program Memory Address 0h must be NOP
700h-7FFh
FIGURE 12-10:
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
For more information, see “MPLAB® ICD 2 In-Circuit
Debugger User’s Guide” (DS51331), available on
Microchip’s web site (www.microchip.com).
To Normal
Connections
FIGURE 12-11:
28-Pin PDIP
28-PIN ICD PINOUT
External
Connector
Signals
*
PIC16F610/16HV610
PIC16F616/16HV616
In-Circuit Debug Device
+5V
0V
VDD
VSS
1
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VDD
CS0
CS1
CS2
RA5
RA4
RA3
RC5
RC4
GND
RA0
RA1
SHUNTEN
RA2
RC0
RC1
RC2
NC
NC
NC
NC
NC
VPP
MCLR/VPP/RA3
2
3
RA1
RA0
CLK
4
Data I/O
5
6
7
8
9
*
*
*
10
11
12
13
14
RC3
NC
ICDCLK
ICDMCLR
ICDDATA
To Normal
Connections
ICD
* Isolation devices (as required)
Note:
To erase, the device VDD must be above
the Bulk Erase VDD minimum given in the
“PIC12F615/12HV615/16F616/16HV616
Memory Programming Specification”
(DS41284)
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 123
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 124
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 13-1: OPCODE FIELD
13.0 INSTRUCTION SET SUMMARY
DESCRIPTIONS
The PIC16F610/616/16HV610/616 instruction set is
highly orthogonal and is comprised of three basic
categories:
Field
Description
f
W
b
Register file address (0x00 to 0x7F)
Working register (accumulator)
• Byte-oriented operations
• Bit-oriented operations
Bit address within an 8-bit file register
Literal field, constant data or label
• Literal and control operations
k
Each PIC16 instruction is a 14-bit word divided into an
opcode, which specifies the instruction type and one or
more operands, which further specify the operation of
the instruction. The formats for each of the categories
is presented in Figure 13-1, while the various opcode
fields are summarized in Table 13-1.
x
Don’t care location (= 0or 1).
The assembler will generate code with x = 0.
It is the recommended form of use for
compatibility with all Microchip software tools.
d
Destination select; d = 0: store result in W,
d = 1: store result in file register f.
Default is d = 1.
Table 13-2 lists the instructions recognized by the
MPASMTM assembler.
PC
TO
C
Program Counter
Time-out bit
Carry bit
For byte-oriented instructions, ‘f’ represents a file
register designator and ‘d’ represents a destination
designator. The file register designator specifies which
file register is to be used by the instruction.
DC
Z
Digit carry bit
Zero bit
The destination designator specifies where the result of
the operation is to be placed. If ‘d’ is zero, the result is
placed in the W register. If ‘d’ is one, the result is placed
in the file register specified in the instruction.
PD
Power-down bit
FIGURE 13-1:
GENERAL FORMAT FOR
INSTRUCTIONS
For bit-oriented instructions, ‘b’ represents a bit field
designator, which selects the bit affected by the
operation, while ‘f’ represents the address of the file in
which the bit is located.
Byte-oriented file register operations
13
8
7
6
0
OPCODE
d
f (FILE #)
For literal and control operations, ‘k’ represents an
d = 0for destination W
d = 1for destination f
f = 7-bit file register address
8-bit or 11-bit constant, or literal value.
One instruction cycle consists of four oscillator periods;
for an oscillator frequency of 4 MHz, this gives a normal
instruction execution time of 1 μs. All instructions are
executed within a single instruction cycle, unless a
conditional test is true, or the program counter is
changed as a result of an instruction. When this occurs,
the execution takes two instruction cycles, with the
second cycle executed as a NOP.
Bit-oriented file register operations
13 10 9
b (BIT #)
7
6
0
OPCODE
f (FILE #)
b = 3-bit bit address
f = 7-bit file register address
All instruction examples use the format ‘0xhh’ to
represent a hexadecimal number, where ‘h’ signifies a
hexadecimal digit.
Literal and control operations
General
13
8
7
0
0
OPCODE
k (literal)
13.1 Read-Modify-Write Operations
k = 8-bit immediate value
Any instruction that specifies a file register as part of
the instruction performs a Read-Modify-Write (RMW)
operation. The register is read, the data is modified,
and the result is stored according to either the instruc-
tion or the destination designator ‘d’. A read operation
is performed on a register even if the instruction writes
to that register.
CALLand GOTOinstructions only
13 11 10
OPCODE
k = 11-bit immediate value
k (literal)
For example, a CLRF PORTA instruction will read
PORTA, clear all the data bits, then write the result back
to PORTA. This example would have the unintended
consequence of clearing the condition that set the RAIF
flag.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 125
PIC16F610/616/16HV610/616
TABLE 13-2: PIC16F610/616/16HV610/616 INSTRUCTION SET
14-Bit Opcode
Mnemonic,
Operands
Status
Affected
Description
Cycles
Notes
MSb
LSb
BYTE-ORIENTED FILE REGISTER OPERATIONS
ADDWF
ANDWF
CLRF
CLRW
COMF
DECF
DECFSZ
INCF
INCFSZ
IORWF
MOVF
MOVWF
NOP
f, d
f, d
f
Add W and f
AND W with f
Clear f
Clear W
Complement f
Decrement f
Decrement f, Skip if 0
Increment f
Increment f, Skip if 0
Inclusive OR W with f
Move f
1
1
1
1
1
1
1(2)
1
1(2)
1
1
1
1
1
1
1
1
1
00 0111 dfff ffff C, DC, Z
1, 2
1, 2
2
00 0101 dfff ffff
00 0001 lfff ffff
00 0001 0xxx xxxx
00 1001 dfff ffff
00 0011 dfff ffff
00 1011 dfff ffff
00 1010 dfff ffff
00 1111 dfff ffff
00 0100 dfff ffff
00 1000 dfff ffff
00 0000 lfff ffff
00 0000 0xx0 0000
00 1101 dfff ffff
00 1100 dfff ffff
Z
Z
Z
Z
Z
–
f, d
f, d
f, d
f, d
f, d
f, d
f, d
f
1, 2
1, 2
1, 2, 3
1, 2
1, 2, 3
1, 2
1, 2
Z
Z
Z
Move W to f
No Operation
–
RLF
RRF
SUBWF
SWAPF
XORWF
f, d
f, d
f, d
f, d
f, d
Rotate Left f through Carry
Rotate Right f through Carry
Subtract W from f
Swap nibbles in f
Exclusive OR W with f
C
C
1, 2
1, 2
1, 2
1, 2
1, 2
00 0010 dfff ffff C, DC, Z
00 1110 dfff ffff
00 0110 dfff ffff
Z
BIT-ORIENTED FILE REGISTER OPERATIONS
BCF
BSF
BTFSC
BTFSS
f, b
f, b
f, b
f, b
Bit Clear f
Bit Set f
Bit Test f, Skip if Clear
Bit Test f, Skip if Set
1
1
1 (2)
1 (2)
01 00bb bfff ffff
1, 2
1, 2
3
01 01bb bfff ffff
01 10bb bfff ffff
01 11bb bfff ffff
3
LITERAL AND CONTROL OPERATIONS
ADDLW
ANDLW
CALL
CLRWDT
GOTO
IORLW
MOVLW
RETFIE
RETLW
RETURN
SLEEP
SUBLW
XORLW
k
k
k
–
k
k
k
–
k
–
–
k
k
Add literal and W
AND literal with W
Call Subroutine
Clear Watchdog Timer
Go to address
1
1
2
1
2
1
1
2
2
2
1
1
1
11 111x kkkk kkkk C, DC, Z
11 1001 kkkk kkkk
10 0kkk kkkk kkkk
Z
00 0000 0110 0100 TO, PD
10 1kkk kkkk kkkk
Inclusive OR literal with W
Move literal to W
11 1000 kkkk kkkk
11 00xx kkkk kkkk
00 0000 0000 1001
11 01xx kkkk kkkk
00 0000 0000 1000
Z
Return from interrupt
Return with literal in W
Return from Subroutine
Go into Standby mode
Subtract W from literal
Exclusive OR literal with W
00 0000 0110 0011 TO, PD
11 110x kkkk kkkk C, DC, Z
11 1010 kkkk kkkk
Z
Note 1: When an I/O register is modified as a function of itself (e.g., MOVF PORTA, 1), the value used will be that value present
on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is driven low by an external
device, the data will be written back with a ‘0’.
2: If this instruction is executed on the TMR0 register (and where applicable, d = 1), the prescaler will be cleared if
assigned to the Timer0 module.
3: If the Program Counter (PC) is modified, or a conditional test is true, the instruction requires two cycles. The second
cycle is executed as a NOP.
DS41288C-page 126
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
13.2 Instruction Descriptions
BCF
Bit Clear f
ADDLW
Add literal and W
Syntax:
[ label ] BCF f,b
Syntax:
[ label ] ADDLW
0 ≤ k ≤ 255
k
Operands:
0 ≤ f ≤ 127
0 ≤ b ≤ 7
Operands:
Operation:
Status Affected:
Description:
(W) + k → (W)
C, DC, Z
Operation:
0→ (f<b>)
Status Affected:
Description:
None
The contents of the W register
are added to the eight-bit literal ‘k’
and the result is placed in the
W register.
Bit ‘b’ in register ‘f’ is cleared.
BSF
Bit Set f
ADDWF
Add W and f
Syntax:
[ label ] BSF f,b
Syntax:
[ label ] ADDWF f,d
Operands:
0 ≤ f ≤ 127
0 ≤ b ≤ 7
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
1→ (f<b>)
Operation:
(W) + (f) → (destination)
Status Affected:
Description:
None
Status Affected: C, DC, Z
Bit ‘b’ in register ‘f’ is set.
Description:
Add the contents of the W register
with register ‘f’. If ‘d’ is ‘0’, the
result is stored in the W register. If
‘d’ is ‘1’, the result is stored back
in register ‘f’.
BTFSC
Bit Test f, Skip if Clear
ANDLW
AND literal with W
Syntax:
[ label ] BTFSC f,b
Syntax:
[ label ] ANDLW
0 ≤ k ≤ 255
k
Operands:
0 ≤ f ≤ 127
0 ≤ b ≤ 7
Operands:
Operation:
Status Affected:
Description:
(W) .AND. (k) → (W)
Operation:
skip if (f<b>) = 0
Z
Status Affected: None
The contents of W register are
AND’ed with the eight-bit literal
‘k’. The result is placed in the W
register.
Description: If bit ‘b’ in register ‘f’ is ‘1’, the next
instruction is executed.
If bit ‘b’ in register ‘f’ is ‘0’, the next
instruction is discarded, and a NOP
is executed instead, making this a
two-cycle instruction.
ANDWF
AND W with f
Syntax:
[ label ] ANDWF f,d
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(W) .AND. (f) → (destination)
Status Affected:
Description:
Z
AND the W register with register
‘f’. If ‘d’ is ‘0’, the result is stored in
the W register. If ‘d’ is ‘1’, the
result is stored back in register ‘f’.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 127
PIC16F610/616/16HV610/616
CLRWDT
Clear Watchdog Timer
BTFSS
Bit Test f, Skip if Set
Syntax:
[ label ] CLRWDT
Syntax:
[ label ] BTFSS f,b
Operands:
Operation:
None
Operands:
0 ≤ f ≤ 127
0 ≤ b < 7
00h → WDT
0→ WDT prescaler,
1→ TO
Operation:
skip if (f<b>) = 1
Status Affected: None
1→ PD
Description:
If bit ‘b’ in register ‘f’ is ‘0’, the next
instruction is executed.
Status Affected: TO, PD
Description:
CLRWDTinstruction resets the
Watchdog Timer. It also resets the
prescaler of the WDT.
If bit ‘b’ is ‘1’, then the next
instruction is discarded and a NOP
is executed instead, making this a
two-cycle instruction.
Status bits TO and PD are set.
CALL
Call Subroutine
COMF
Complement f
Syntax:
[ label ] CALL k
0 ≤ k ≤ 2047
Syntax:
[ label ] COMF f,d
Operands:
Operation:
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
(PC)+ 1→ TOS,
k → PC<10:0>,
(PCLATH<4:3>) → PC<12:11>
Operation:
(f) → (destination)
Status Affected:
Description:
Z
Status Affected: None
The contents of register ‘f’ are
complemented. If ‘d’ is ‘0’, the
result is stored in W. If ‘d’ is ‘1’,
the result is stored back in
register ‘f’.
Description:
Call Subroutine. First, return
address (PC + 1) is pushed onto
the stack. The eleven-bit
immediate address is loaded into
PC bits <10:0>. The upper bits of
the PC are loaded from PCLATH.
CALLis a two-cycle instruction.
CLRF
Clear f
DECF
Decrement f
Syntax:
[ label ] CLRF
0 ≤ f ≤ 127
f
Syntax:
[ label ] DECF f,d
Operands:
Operation:
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
00h → (f)
1→ Z
Operation:
(f) - 1 → (destination)
Status Affected:
Description:
Z
Status Affected:
Description:
Z
The contents of register ‘f’ are
cleared and the Z bit is set.
Decrement register ‘f’. If ‘d’ is ‘0’,
the result is stored in the W
register. If ‘d’ is ‘1’, the result is
stored back in register ‘f’.
CLRW
Clear W
Syntax:
[ label ] CLRW
Operands:
Operation:
None
00h → (W)
1→ Z
Status Affected:
Description:
Z
W register is cleared. Zero bit (Z)
is set.
DS41288C-page 128
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
DECFSZ
Decrement f, Skip if 0
INCFSZ
Increment f, Skip if 0
Syntax:
[ label ] DECFSZ f,d
Syntax:
[ label ] INCFSZ f,d
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(f) - 1 → (destination);
skip if result = 0
Operation:
(f) + 1 → (destination),
skip if result = 0
Status Affected: None
Status Affected: None
Description:
The contents of register ‘f’ are
Description:
The contents of register ‘f’ are
decremented. If ‘d’ is ‘0’, the result
is placed in the W register. If ‘d’ is
‘1’, the result is placed back in
register ‘f’.
incremented. If ‘d’ is ‘0’, the result
is placed in the W register. If ‘d’ is
‘1’, the result is placed back in
register ‘f’.
If the result is ‘1’, the next
instruction is executed. If the
result is ‘0’, then a NOPis
executed instead, making it a
two-cycle instruction.
If the result is ‘1’, the next
instruction is executed. If the
result is ‘0’, a NOPis executed
instead, making it a two-cycle
instruction.
GOTO
Unconditional Branch
IORLW
Inclusive OR literal with W
Syntax:
[ label ] GOTO k
0 ≤ k ≤ 2047
Syntax:
[ label ] IORLW k
0 ≤ k ≤ 255
Operands:
Operation:
Operands:
Operation:
Status Affected:
Description:
k → PC<10:0>
PCLATH<4:3> → PC<12:11>
(W) .OR. k → (W)
Z
Status Affected: None
The contents of the W register are
OR’ed with the eight-bit literal ‘k’.
The result is placed in the
W register.
Description:
GOTOis an unconditional branch.
The eleven-bit immediate value is
loaded into PC bits <10:0>. The
upper bits of PC are loaded from
PCLATH<4:3>. GOTOis a
two-cycle instruction.
IORWF
Inclusive OR W with f
INCF
Increment f
Syntax:
[ label ] IORWF f,d
Syntax:
[ label ] INCF f,d
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(W) .OR. (f) → (destination)
Operation:
(f) + 1 → (destination)
Status Affected:
Description:
Z
Status Affected:
Description:
Z
Inclusive OR the W register with
register ‘f’. If ‘d’ is ‘0’, the result is
placed in the W register. If ‘d’ is
‘1’, the result is placed back in
register ‘f’.
The contents of register ‘f’ are
incremented. If ‘d’ is ‘0’, the result
is placed in the W register. If ‘d’ is
‘1’, the result is placed back in
register ‘f’.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 129
PIC16F610/616/16HV610/616
MOVWF
Move W to f
[ label ] MOVWF
0 ≤ f ≤ 127
(W) → (f)
MOVF
Move f
Syntax:
f
Syntax:
Operands:
[ label ] MOVF f,d
Operands:
Operation:
Status Affected:
Description:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(f) → (dest)
None
Status Affected:
Description:
Z
Move data from W register to
register ‘f’.
The contents of register ‘f’ is
moved to a destination dependent
upon the status of ‘d’. If d = 0,
destination is W register. If d = 1,
the destination is file register ‘f’
itself. d = 1is useful to test a file
register since status flag Z is
affected.
Words:
1
1
Cycles:
Example:
MOVW
F
OPTION
Before Instruction
OPTION = 0xFF
Words:
1
1
W
=
0x4F
After Instruction
Cycles:
Example:
OPTION = 0x4F
W
MOVF
FSR, 0
=
0x4F
After Instruction
W
=
value in FSR
register
Z
=
1
MOVLW
Syntax:
Move literal to W
NOP
No Operation
[ label ] MOVLW k
0 ≤ k ≤ 255
Syntax:
[ label ] NOP
Operands:
Operation:
Operands:
Operation:
Status Affected:
Description:
Words:
None
k → (W)
No operation
Status Affected: None
None
Description:
The eight-bit literal ‘k’ is loaded into
W register. The “don’t cares” will
assemble as ‘0’s.
No operation.
1
Cycles:
1
Words:
1
1
NOP
Example:
Cycles:
Example:
MOVLW
0x5A
After Instruction
W
=
0x5A
DS41288C-page 130
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
RETFIE
Return from Interrupt
[ label ] RETFIE
None
RETLW
Return with literal in W
[ label ] RETLW k
0 ≤ k ≤ 255
Syntax:
Syntax:
Operands:
Operation:
Operands:
Operation:
TOS → PC,
1→ GIE
k → (W);
TOS → PC
Status Affected:
Description:
None
Status Affected:
Description:
None
Return from Interrupt. Stack is
POPed and Top-of-Stack (TOS) is
loaded in the PC. Interrupts are
enabled by setting Global
Interrupt Enable bit, GIE
The W register is loaded with the
eight-bit literal ‘k’. The program
counter is loaded from the top of
the stack (the return address).
This is a two-cycle instruction.
(INTCON<7>). This is a two-cycle
instruction.
Words:
1
2
Cycles:
Example:
Words:
1
CALL TABLE;W contains
Cycles:
Example:
2
;table offset
;value
RETFIE
GOTO DONE
•
•
ADDWF PC ;W = offset
RETLW k1 ;Begin table
After Interrupt
PC = TOS
TABLE
GIE =
1
RETLW k2
;
•
•
•
RETLW kn ;End of table
DONE
Before Instruction
W
=
0x07
After Instruction
W
=
value of k8
RETURN
Return from Subroutine
Syntax:
[ label ] RETURN
None
Operands:
Operation:
TOS → PC
Status Affected: None
Description: Return from subroutine. The stack
is POPed and the top of the stack
(TOS) is loaded into the program
counter. This is a two-cycle
instruction.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 131
PIC16F610/616/16HV610/616
RLF
Rotate Left f through Carry
SLEEP
Enter Sleep mode
[ label ] SLEEP
None
Syntax:
Operands:
[ label ]
RLF f,d
Syntax:
0 ≤ f ≤ 127
d ∈ [0,1]
Operands:
Operation:
00h → WDT,
0→ WDT prescaler,
1→ TO,
Operation:
See description below
C
Status Affected:
Description:
0→ PD
The contents of register ‘f’ are
rotated one bit to the left through
the Carry flag. If ‘d’ is ‘0’, the
result is placed in the W register.
If ‘d’ is ‘1’, the result is stored
back in register ‘f’.
Status Affected:
Description:
TO, PD
The power-down Status bit, PD is
cleared. Time-out Status bit, TO
is set. Watchdog Timer and its
prescaler are cleared.
The processor is put into Sleep
mode with the oscillator stopped.
C
Register f
Words:
1
1
Cycles:
Example:
RLF
REG1,0
Before Instruction
REG1
C
=
=
1110 0110
0
After Instruction
REG1
W
C
=
=
=
1110 0110
1100 1100
1
SUBLW
Subtract W from literal
RRF
Rotate Right f through Carry
Syntax:
[ label ] SUBLW k
0 ≤ k ≤ 255
Syntax:
[ label ] RRF f,d
Operands:
Operation:
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
k - (W) → (W)
Operation:
See description below
C
Status Affected: C, DC, Z
Status Affected:
Description:
Description: The W register is subtracted (2’s
complement method) from the
eight-bit literal ‘k’. The result is
placed in the W register.
The contents of register ‘f’ are
rotated one bit to the right through
the Carry flag. If ‘d’ is ‘0’, the
result is placed in the W register.
If ‘d’ is ‘1’, the result is placed
back in register ‘f’.
Result
Condition
C = 0
W > k
C
Register f
C = 1
W ≤ k
DC = 0
DC = 1
W<3:0> > k<3:0>
W<3:0> ≤ k<3:0>
DS41288C-page 132
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
SUBWF
Subtract W from f
XORWF
Exclusive OR W with f
Syntax:
[ label ] SUBWF f,d
Syntax:
[ label ] XORWF f,d
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(f) - (W) → (destination)
Operation:
(W) .XOR. (f) → (destination)
Status Affected: C, DC, Z
Status Affected:
Description:
Z
Description:
Subtract (2’s complement method)
Exclusive OR the contents of the
W register with register ‘f’. If ‘d’ is
‘0’, the result is stored in the W
register. If ‘d’ is ‘1’, the result is
stored back in register ‘f’.
W register from register ‘f’. If ‘d’ is
‘0’, the result is stored in the W
register. If ‘d’ is ‘1’, the result is
stored back in register ‘f’.
C = 0
W > f
C = 1
W ≤ f
DC = 0
DC = 1
W<3:0> > f<3:0>
W<3:0> ≤ f<3:0>
SWAPF
Swap Nibbles in f
Syntax:
[ label ] SWAPF f,d
Operands:
0 ≤ f ≤ 127
d ∈ [0,1]
Operation:
(f<3:0>) → (destination<7:4>),
(f<7:4>) → (destination<3:0>)
Status Affected: None
Description:
The upper and lower nibbles of
register ‘f’ are exchanged. If ‘d’ is
‘0’, the result is placed in the W
register. If ‘d’ is ‘1’, the result is
placed in register ‘f’.
XORLW
Exclusive OR literal with W
Syntax:
[ label ] XORLW k
0 ≤ k ≤ 255
Operands:
Operation:
Status Affected:
Description:
(W) .XOR. k → (W)
Z
The contents of the W register
are XOR’ed with the eight-bit
literal ‘k’. The result is placed in
the W register.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 133
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 134
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
14.1 MPLAB Integrated Development
Environment Software
14.0 DEVELOPMENT SUPPORT
The PIC® microcontrollers are supported with a full
range of hardware and software development tools:
The MPLAB IDE software brings an ease of software
development previously unseen in the 8/16-bit micro-
controller market. The MPLAB IDE is a Windows®
operating system-based application that contains:
• Integrated Development Environment
- MPLAB® IDE Software
• Assemblers/Compilers/Linkers
- MPASMTM Assembler
• A single graphical interface to all debugging tools
- Simulator
- MPLAB C18 and MPLAB C30 C Compilers
- MPLINKTM Object Linker/
MPLIBTM Object Librarian
- Programmer (sold separately)
- Emulator (sold separately)
- In-Circuit Debugger (sold separately)
• A full-featured editor with color-coded context
• A multiple project manager
- MPLAB ASM30 Assembler/Linker/Library
• Simulators
- MPLAB SIM Software Simulator
• Emulators
• Customizable data windows with direct edit of
contents
- MPLAB ICE 2000 In-Circuit Emulator
- MPLAB REAL ICE™ In-Circuit Emulator
• In-Circuit Debugger
• High-level source code debugging
• Visual device initializer for easy register
initialization
- MPLAB ICD 2
• Mouse over variable inspection
• Device Programmers
• Drag and drop variables from source to watch
windows
- PICSTART® Plus Development Programmer
- MPLAB PM3 Device Programmer
- PICkit™ 2 Development Programmer
• Extensive on-line help
• Integration of select third party tools, such as
HI-TECH Software C Compilers and IAR
C Compilers
• Low-Cost Demonstration and Development
Boards and Evaluation Kits
The MPLAB IDE allows you to:
• Edit your source files (either assembly or C)
• One touch assemble (or compile) and download
to PIC MCU emulator and simulator tools
(automatically updates all project information)
• Debug using:
- Source files (assembly or C)
- Mixed assembly and C
- Machine code
MPLAB IDE supports multiple debugging tools in a
single development paradigm, from the cost-effective
simulators, through low-cost in-circuit debuggers, to
full-featured emulators. This eliminates the learning
curve when upgrading to tools with increased flexibility
and power.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 135
PIC16F610/616/16HV610/616
14.2 MPASM Assembler
14.5 MPLAB ASM30 Assembler, Linker
and Librarian
The MPASM Assembler is a full-featured, universal
macro assembler for all PIC MCUs.
MPLAB ASM30 Assembler produces relocatable
machine code from symbolic assembly language for
dsPIC30F devices. MPLAB C30 C Compiler uses the
assembler to produce its object file. The assembler
generates relocatable object files that can then be
archived or linked with other relocatable object files and
archives to create an executable file. Notable features
of the assembler include:
The MPASM Assembler generates relocatable object
files for the MPLINK Object Linker, Intel® standard HEX
files, MAP files to detail memory usage and symbol
reference, absolute LST files that contain source lines
and generated machine code and COFF files for
debugging.
The MPASM Assembler features include:
• Integration into MPLAB IDE projects
• Support for the entire dsPIC30F instruction set
• Support for fixed-point and floating-point data
• Command line interface
• User-defined macros to streamline
assembly code
• Rich directive set
• Conditional assembly for multi-purpose
source files
• Flexible macro language
• MPLAB IDE compatibility
• Directives that allow complete control over the
assembly process
14.6 MPLAB SIM Software Simulator
14.3 MPLAB C18 and MPLAB C30
C Compilers
The MPLAB SIM Software Simulator allows code
development in a PC-hosted environment by simulat-
ing the PIC MCUs and dsPIC® DSCs on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a comprehensive stimulus controller. Registers can be
logged to files for further run-time analysis. The trace
buffer and logic analyzer display extend the power of
the simulator to record and track program execution,
actions on I/O, most peripherals and internal registers.
The MPLAB C18 and MPLAB C30 Code Development
Systems are complete ANSI
C
compilers for
Microchip’s PIC18 and PIC24 families of microcontrol-
lers and the dsPIC30 and dsPIC33 family of digital sig-
nal controllers. These compilers provide powerful
integration capabilities, superior code optimization and
ease of use not found with other compilers.
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
The MPLAB SIM Software Simulator fully supports
symbolic debugging using the MPLAB C18 and
MPLAB C30 C Compilers, and the MPASM and
MPLAB ASM30 Assemblers. The software simulator
offers the flexibility to develop and debug code outside
of the hardware laboratory environment, making it an
excellent, economical software development tool.
14.4 MPLINK Object Linker/
MPLIB Object Librarian
The MPLINK Object Linker combines relocatable
objects created by the MPASM Assembler and the
MPLAB C18 C Compiler. It can link relocatable objects
from precompiled libraries, using directives from a
linker script.
The MPLIB Object Librarian manages the creation and
modification of library files of precompiled code. When
a routine from a library is called from a source file, only
the modules that contain that routine will be linked in
with the application. This allows large libraries to be
used efficiently in many different applications.
The object linker/library features include:
• Efficient linking of single libraries instead of many
smaller files
• Enhanced code maintainability by grouping
related modules together
• Flexible creation of libraries with easy module
listing, replacement, deletion and extraction
DS41288C-page 136
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
14.7 MPLAB ICE 2000
High-Performance
14.9 MPLAB ICD 2 In-Circuit Debugger
Microchip’s In-Circuit Debugger, MPLAB ICD 2, is a
powerful, low-cost, run-time development tool,
connecting to the host PC via an RS-232 or high-speed
In-Circuit Emulator
The MPLAB ICE 2000 In-Circuit Emulator is intended
to provide the product development engineer with a
complete microcontroller design tool set for PIC
microcontrollers. Software control of the MPLAB ICE
2000 In-Circuit Emulator is advanced by the MPLAB
Integrated Development Environment, which allows
editing, building, downloading and source debugging
from a single environment.
USB interface. This tool is based on the Flash PIC
MCUs and can be used to develop for these and other
PIC MCUs and dsPIC DSCs. The MPLAB ICD 2 utilizes
the in-circuit debugging capability built into the Flash
devices. This feature, along with Microchip’s In-Circuit
Serial ProgrammingTM (ICSPTM) protocol, offers cost-
effective, in-circuit Flash debugging from the graphical
user interface of the MPLAB Integrated Development
Environment. This enables a designer to develop and
debug source code by setting breakpoints, single step-
ping and watching variables, and CPU status and
peripheral registers. Running at full speed enables
testing hardware and applications in real time. MPLAB
ICD 2 also serves as a development programmer for
selected PIC devices.
The MPLAB ICE 2000 is a full-featured emulator
system with enhanced trace, trigger and data monitor-
ing features. Interchangeable processor modules allow
the system to be easily reconfigured for emulation of
different processors. The architecture of the MPLAB
ICE 2000 In-Circuit Emulator allows expansion to
support new PIC microcontrollers.
The MPLAB ICE 2000 In-Circuit Emulator system has
been designed as a real-time emulation system with
advanced features that are typically found on more
expensive development tools. The PC platform and
Microsoft® Windows® 32-bit operating system were
chosen to best make these features available in a
simple, unified application.
14.10 MPLAB PM3 Device Programmer
The MPLAB PM3 Device Programmer is a universal,
CE compliant device programmer with programmable
voltage verification at VDDMIN and VDDMAX for
maximum reliability. It features a large LCD display
(128 x 64) for menus and error messages and a modu-
lar, detachable socket assembly to support various
package types. The ICSP™ cable assembly is included
as a standard item. In Stand-Alone mode, the MPLAB
PM3 Device Programmer can read, verify and program
PIC devices without a PC connection. It can also set
code protection in this mode. The MPLAB PM3
connects to the host PC via an RS-232 or USB cable.
The MPLAB PM3 has high-speed communications and
optimized algorithms for quick programming of large
memory devices and incorporates an SD/MMC card for
file storage and secure data applications.
14.8 MPLAB REAL ICE In-Circuit
Emulator System
MPLAB REAL ICE In-Circuit Emulator System is
Microchip’s next generation high-speed emulator for
Microchip Flash DSC® and MCU devices. It debugs and
programs PIC® and dsPIC® Flash microcontrollers with
the easy-to-use, powerful graphical user interface of the
MPLAB Integrated Development Environment (IDE),
included with each kit.
The MPLAB REAL ICE probe is connected to the design
engineer’s PC using a high-speed USB 2.0 interface and
is connected to the target with either a connector
compatible with the popular MPLAB ICD 2 system
(RJ11) or with the new high speed, noise tolerant, low-
voltage differential signal (LVDS) interconnection
(CAT5).
MPLAB REAL ICE is field upgradeable through future
firmware downloads in MPLAB IDE. In upcoming
releases of MPLAB IDE, new devices will be supported,
and new features will be added, such as software break-
points and assembly code trace. MPLAB REAL ICE
offers significant advantages over competitive emulators
including low-cost, full-speed emulation, real-time
variable watches, trace analysis, complex breakpoints, a
ruggedized probe interface and long (up to three meters)
interconnection cables.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 137
PIC16F610/616/16HV610/616
14.11 PICSTART Plus Development
Programmer
14.13 Demonstration, Development and
Evaluation Boards
The PICSTART Plus Development Programmer is an
easy-to-use, low-cost, prototype programmer. It
connects to the PC via a COM (RS-232) port. MPLAB
Integrated Development Environment software makes
using the programmer simple and efficient. The
PICSTART Plus Development Programmer supports
most PIC devices in DIP packages up to 40 pins.
Larger pin count devices, such as the PIC16C92X and
PIC17C76X, may be supported with an adapter socket.
The PICSTART Plus Development Programmer is CE
compliant.
A wide variety of demonstration, development and
evaluation boards for various PIC MCUs and dsPIC
DSCs allows quick application development on fully func-
tional systems. Most boards include prototyping areas for
adding custom circuitry and provide application firmware
and source code for examination and modification.
The boards support a variety of features, including LEDs,
temperature sensors, switches, speakers, RS-232
interfaces, LCD displays, potentiometers and additional
EEPROM memory.
The demonstration and development boards can be
used in teaching environments, for prototyping custom
circuits and for learning about various microcontroller
applications.
14.12 PICkit 2 Development Programmer
The PICkit™ 2 Development Programmer is a low-cost
programmer and selected Flash device debugger with
an easy-to-use interface for programming many of
Microchip’s baseline, mid-range and PIC18F families of
Flash memory microcontrollers. The PICkit 2 Starter Kit
includes a prototyping development board, twelve
sequential lessons, software and HI-TECH’s PICC™
Lite C compiler, and is designed to help get up to speed
quickly using PIC® microcontrollers. The kit provides
everything needed to program, evaluate and develop
applications using Microchip’s powerful, mid-range
Flash memory family of microcontrollers.
In addition to the PICDEM™ and dsPICDEM™ demon-
stration/development board series of circuits, Microchip
has a line of evaluation kits and demonstration software
®
for analog filter design, KEELOQ security ICs, CAN,
IrDA®, PowerSmart® battery management, SEEVAL®
evaluation system, Sigma-Delta ADC, flow rate
sensing, plus many more.
Check the Microchip web page (www.microchip.com)
and the latest “Product Selector Guide” (DS00148) for
the complete list of demonstration, development and
evaluation kits.
DS41288C-page 138
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
15.0 ELECTRICAL SPECIFICATIONS
(†)
Absolute Maximum Ratings
Ambient temperature under bias..........................................................................................................-40° to +125°C
Storage temperature ........................................................................................................................ -65°C to +150°C
Voltage on VDD with respect to VSS ................................................................................................... -0.3V to +6.5V
Voltage on MCLR with respect to Vss ............................................................................................... -0.3V to +13.5V
Voltage on all other pins with respect to VSS ........................................................................... -0.3V to (VDD + 0.3V)
Total power dissipation(1) ............................................................................................................................... 800 mW
Maximum current out of VSS pin ...................................................................................................................... 95 mA
Maximum current into VDD pin ......................................................................................................................... 95 mA
Input clamp current, IIK (VI < 0 or VI > VDD)............................................................................................................... 20 mA
Output clamp current, IOK (Vo < 0 or Vo >VDD)......................................................................................................... 20 mA
Maximum output current sunk by any I/O pin....................................................................................................25 mA
Maximum output current sourced by any I/O pin .............................................................................................. 25 mA
Maximum current sunk by PORTA and PORTC (combined) ........................................................................... 90 mA
Maximum current sourced PORTA and PORTC (combined)........................................................................... 90 mA
Note 1: Power dissipation is calculated as follows: PDIS = VDD x {IDD – ∑ IOH} + ∑ {(VDD – VOH) x IOH} + ∑(VOl x IOL).
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure above maximum rating conditions for
extended periods may affect device reliability.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 139
PIC16F610/616/16HV610/616
FIGURE 15-1:
PIC16F610/616 VOLTAGE-FREQUENCY GRAPH,
-40°C ≤ TA ≤ +125°C
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
0
8
10
20
Frequency (MHz)
Note 1: The shaded region indicates the permissible combinations of voltage and frequency.
FIGURE 15-2:
PIC16HV610/616 VOLTAGE-FREQUENCY GRAPH,
-40°C ≤ TA ≤ +125°C
5.0
4.5
4.0
3.5
3.0
2.5
2.0
0
8
10
20
Frequency (MHz)
Note 1: The shaded region indicates the permissible combinations of voltage and frequency.
DS41288C-page 140
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
FIGURE 15-3:
PIC16F610/616 VOLTAGE-FREQUENCY GRAPH,
-40°C ≤ TA ≤ +125°C
125
± 5%
85
60
25
0
± 2%
± 1%
2.0
2.5
3.0
3.5
4.0
VDD (V)
4.5
5.0
5.5
FIGURE 15-4:
PIC16HV610/616 VOLTAGE-FREQUENCY GRAPH,
-40°C ≤ TA ≤ +125°C
125
85
60
25
0
± 5%
± 2%
± 1%
2.0
2.5
3.0
3.5
4.0
4.5
5.0
VDD (V)
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 141
PIC16F610/616/16HV610/616
15.1 DC Characteristics: PIC16F610/616/16HV610/616-I (Industrial)
PIC16F610/616/16HV610/616-E (Extended)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
No.
Sym
Characteristic
Min Typ† Max Units
Conditions
VDD
Supply Voltage
PIC16F610/616
PIC16HV610/616
PIC16F610/616
PIC16HV610/616
PIC16F610/616
PIC16HV610/616
PIC16F610/616
PIC16HV610/616
D001
2.0
2.0
2.0
2.0
3.0
3.0
4.5
4.5
1.5
—
—
—
—
—
—
—
—
—
5.5
5.0
5.5
5.0
5.5
5.0
5.5
5.0
—
V
V
V
V
V
V
V
V
V
FOSC < = 4 MHz
D001
FOSC < = 4 MHz
FOSC < = 8 MHz
FOSC < = 8 MHz
FOSC < = 10 MHz
FOSC < = 10 MHz
FOSC < = 20 MHz
FOSC < = 20 MHz
Device in Sleep mode
D001B
D001B
D001C
D001C
D001D
D001D
D002* VDR
RAM Data Retention
Voltage(1)
D003 VPOR
VDD Start Voltage to
ensure internal Power-on
Reset signal
—
VSS
—
—
—
V
See Section 12.3.1 “Power-on Reset
(POR)” for details.
D004* SVDD
VDD Rise Rate to ensure
internal Power-on Reset
signal
0.05
V/ms See Section 12.3.1 “Power-on Reset
(POR)” for details.
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: This is the limit to which VDD can be lowered in Sleep mode without losing RAM data.
DS41288C-page 142
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
15.2 DC Characteristics: PIC16F610/616/16HV610/616-I (Industrial)
PIC16F610/616/16HV610/616-E (Extended)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Param
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Conditions
Units
Device Characteristics
Min
Typ†
Max
No.
VDD
Note
D010
Supply Current (IDD)(1, 2)
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
11
18
16
28
μA
μA
μA
μA
μA
μA
μA
μA
mA
μA
μA
μA
μA
μA
mA
μA
μA
mA
μA
μA
mA
μA
μA
mA
mA
mA
2.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
4.5
5.0
FOSC = 32 kHz
LP Oscillator mode
35
54
D011*
D012
D013*
D014
D016*
D017
D018
D019
140
220
380
260
420
0.8
240
380
550
360
650
1.1
FOSC = 1 MHz
XT Oscillator mode
FOSC = 4 MHz
XT Oscillator mode
130
215
360
220
375
0.65
340
500
0.8
220
360
520
340
550
1.0
FOSC = 1 MHz
EC Oscillator mode
FOSC = 4 MHz
EC Oscillator mode
450
700
1.2
FOSC = 4 MHz
INTOSC mode
410
700
1.30
230
400
0.63
2.6
650
950
1.65
400
680
1.1
FOSC = 8 MHz
INTOSC mode
FOSC = 4 MHz
EXTRC mode(3)
3.25
3.35
FOSC = 20 MHz
HS Oscillator mode
2.8
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave,
from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O
pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have
an impact on the current consumption.
3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can
be extended by the formula IR = VDD/2REXT (mA) with REXT in kΩ.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 143
PIC16F610/616/16HV610/616
15.3 DC Characteristics: PIC16F616/16HV616- I (Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
DC CHARACTERISTICS
Conditions
Param
No.
Device Characteristics
Min
Typ†
Max
Units
VDD
Note
D020
Power-down Base
Current(IPD)(2)
—
0.05
1.2
μA
2.0
WDT, BOR, Comparators, VREF and
T1OSC disabled
—
—
—
—
—
4
0.15
0.35
150
350
350
—
1.5
1.8
500
—
μA
μA
nA
μA
μA
mA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
3.0
5.0
3.0
2.0
3.0
5.0
2.0
3.0
5.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
3.0
5.0
PIC16F610/616
-40°C ≤ TA ≤ +25°C
PIC16HV610/616
—
50
NOTE 3
WDT Current(1)
D021
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
30
2
8
D022
D023
3
BOR Current(1)
4
32
Comparator Current(1), both
comparators enabled
60
120
30
D024
D025*
D026
D027
CVREF Current(1) (high range)
CVREF Current(1) (low range)
T1OSC Current(1), 32.768 kHz
45
55
75
95
39
47
59
72
98
124
7.0
8.0
12
45
5.0
6.0
0.30
0.36
1.6
1.9
A/D Current(1), no conversion in
progress
Legend: TBD = To Be Determined
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this
peripheral is enabled. The peripheral Δ current can be determined by subtracting the base IDD or IPD
current from this limit. Max values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is
measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: Shunt regulator is always enabled and always draws operating current.
DS41288C-page 144
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
15.4 DC Characteristics: PIC16F610/616/16HV610/616-E (Extended)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature
-40°C ≤ TA ≤ +125°C for extended
Conditions
Units
Param
No.
Device Characteristics Min
Typ†
Max
VDD
Note
D020E Power-down Base
—
0.05
9
μA
2.0
WDT, BOR, Comparators, VREF and
T1OSC disabled
Current (IPD)(2)
—
—
—
—
4
0.15
0.35
350
350
—
11
15
μA
μA
μA
μA
nA
3.0
5.0
2.0
3.0
5.0
PIC16F610/616
PIC16HV610/616
D021E
—
—
200
Note 3
WDT Current(1)
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
2
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
70
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
2.0
3.0
5.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
2.0
3.0
5.0
3.0
5.0
8
D022E
D023E
3
BOR Current(1)
4
32
60
120
30
45
75
39
59
98
4.5
5
Comparator Current(1), both
comparators enabled
D024E
D025E*
D026E
D027E
CVREF Current(1) (high range)
CVREF Current(1) (low range)
T1OSC Current(1), 32.768 kHz
90
120
91
117
156
25
30
6
40
0.30
0.36
12
A/D Current(1), no conversion in
progress
16
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this
peripheral is enabled. The peripheral Δ current can be determined by subtracting the base IDD or IPD
current from this limit. Max values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is
measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: Shunt regulator is always enabled and always draws operating current.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 145
PIC16F610/616/16HV610/616
15.5 DC Characteristics: PIC16F610/616/16HV610/616-I (Industrial)
PIC16F610/616/16HV610/616-E (Extended)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
Sym
No.
Characteristic
Min
Typ†
Max
Units
Conditions
VIL
Input Low Voltage
I/O port:
with TTL buffer
D030
D030A
D031
D032
D033
D033A
Vss
Vss
Vss
VSS
VSS
VSS
—
—
—
—
—
—
0.8
V
V
V
V
V
V
4.5V ≤ VDD ≤ 5.5V
0.15 VDD
0.2 VDD
0.2 VDD
0.3
2.0V ≤ VDD ≤ 4.5V
2.0V ≤ VDD ≤ 5.5V
with Schmitt Trigger buffer
(1)
MCLR, OSC1 (RC mode)
OSC1 (XT and LP modes)
OSC1 (HS mode)
Input High Voltage
I/O ports:
0.3 VDD
VIH
—
—
—
—
—
—
—
—
D040
with TTL buffer
2.0
0.25 VDD + 0.8
0.8 VDD
0.8 VDD
1.6
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
4.5V ≤ VDD ≤ 5.5V
2.0V ≤ VDD ≤ 4.5V
2.0V ≤ VDD ≤ 5.5V
D040A
D041
with Schmitt Trigger buffer
MCLR
D042
D043
OSC1 (XT and LP modes)
OSC1 (HS mode)
D043A
D043B
0.7 VDD
0.9 VDD
OSC1 (RC mode)
(Note 1)
(2)
IIL
Input Leakage Current
D060
I/O ports
—
0.1
1
μA VSS ≤ VPIN ≤ VDD,
Pin at high-impedance
(3)
D061
D063
MCLR
—
—
0.1
0.1
5
5
μA VSS ≤ VPIN ≤ VDD
OSC1
μA VSS ≤ VPIN ≤ VDD, XT, HS and
LP oscillator configuration
D070* IPUR
VOL
PORTA Weak Pull-up Current
50
—
250
—
400
0.6
—
μA VDD = 5.0V, VPIN = VSS
(4)
Output Low Voltage
D080
I/O ports
V
V
IOL = 8.5 mA, VDD = 4.5V (Ind.)
IOH = -3.0 mA, VDD = 4.5V (Ind.)
(4)
VOH
Output High Voltage
D090
I/O ports
VDD – 0.7
—
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external
clock in RC mode.
2: Negative current is defined as current sourced by the pin.
3: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
4: Including OSC2 in CLKOUT mode.
DS41288C-page 146
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
15.5 DC Characteristics: PIC16F610/616/16HV610/616-I (Industrial)
PIC16F610/616/16HV610/616-E (Extended) (Continued)
Standard Operating Conditions (unless otherwise stated)
DC CHARACTERISTICS
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
Sym
No.
Characteristic
Min
Typ†
Max
Units
Conditions
Capacitive Loading Specs on
Output Pins
D101* COSC2 OSC2 pin
—
—
—
—
15
50
pF In XT, HS and LP modes when
external clock is used to drive
OSC1
D101A* CIO
All I/O pins
pF
Program Flash Memory
Cell Endurance
Cell Endurance
VDD for Read
D130
EP
10K
1K
100K
10K
—
—
—
E/W -40°C ≤ TA ≤ +85°C
E/W +85°C ≤ TA ≤ +125°C
D130A ED
D131
VPR
VMIN
5.5
V
VMIN = Minimum operating
voltage
D132
D133
D134
VPEW
TPEW
TRETD
VDD for Erase/Write
4.5
—
—
2
5.5
2.5
—
V
Erase/Write cycle time
Characteristic Retention
ms
40
—
Year Provided no other specifications
are violated
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external
clock in RC mode.
2: Negative current is defined as current sourced by the pin.
3: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
4: Including OSC2 in CLKOUT mode.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 147
PIC16F610/616/16HV610/616
15.6 Thermal Considerations
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +125°C
Param
Sym
No.
Characteristic
Typ
Units
Conditions
14-pin PDIP package
TH01
θJA
Thermal Resistance
Junction to Ambient
70
85.0
100
46.3
32.5
31.0
31.7
2.6
C/W
C/W
C/W
C/W
C/W
C/W
C/W
C/W
C
14-pin SOIC package
14-pin TSSOP package
16-pin QFN 4x4mm package
14-pin PDIP package
TH02
θJC
Thermal Resistance
Junction to Case
14-pin SOIC package
14-pin TSSOP package
16-pin QFN 4x4mm package
TH03
TH04
TH05
TDIE
PD
Die Temperature
Power Dissipation
150
—
W
PD = PINTERNAL + PI/O
PINTERNAL Internal Power Dissipation
—
W
PINTERNAL = IDD x VDD
(NOTE 1)
TH06
TH07
PI/O
I/O Power Dissipation
Derated Power
—
—
W
W
PI/O = Σ (IOL * VOL) + Σ (IOH * (VDD - VOH))
PDER = PDMAX (TDIE - TA)/θJA
(NOTE 2)
PDER
Note 1: IDD is current to run the chip alone without driving any load on the output pins.
2: TA = Ambient Temperature.
DS41288C-page 148
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
15.7
Timing Parameter Symbology
The timing parameter symbols have been created with
one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase letters (pp) and their meanings:
pp
cc
T
Time
CCP1
CLKOUT
CS
osc
rd
OSC1
RD
ck
cs
di
rw
sc
ss
t0
RD or WR
SCK
SDI
do
dt
SDO
SS
Data in
I/O Port
MCLR
T0CKI
T1CKI
WR
io
t1
mc
wr
Uppercase letters and their meanings:
S
F
H
I
Fall
P
R
V
Z
Period
High
Rise
Invalid (High-impedance)
Low
Valid
L
High-impedance
FIGURE 15-5:
LOAD CONDITIONS
Load Condition
Pin
CL
VSS
Legend: CL = 50 pF for all pins
15 pF for OSC2 output
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 149
PIC16F610/616/16HV610/616
15.8 AC Characteristics: PIC16F610/616/16HV610/616 (Industrial, Extended)
FIGURE 15-6:
CLOCK TIMING
Q4
Q1
Q2
Q3
Q4
Q1
OSC1/CLKIN
OS02
OS04
OS04
OS03
OSC2/CLKOUT
(LP,XT,HS Modes)
OSC2/CLKOUT
(CLKOUT Mode)
TABLE 15-1: CLOCK OSCILLATOR TIMING REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +125°C
Param
Sym
No.
Characteristic
Min
Typ†
Max
Units
kHz
Conditions
(1)
OS01
FOSC
TOSC
TCY
External CLKIN Frequency
DC
DC
DC
DC
—
—
—
37
4
LP Oscillator mode
MHz XT Oscillator mode
MHz HS Oscillator mode
MHz EC Oscillator mode
—
20
20
—
4
—
(1)
Oscillator Frequency
32.768
—
kHz
LP Oscillator mode
0.1
1
MHz XT Oscillator mode
MHz HS Oscillator mode
MHz RC Oscillator mode
—
20
4
DC
27
250
50
50
—
—
(1)
OS02
External CLKIN Period
—
∞
∞
∞
∞
μs
ns
ns
ns
μs
ns
ns
ns
ns
μs
ns
ns
ns
ns
ns
LP Oscillator mode
XT Oscillator mode
HS Oscillator mode
EC Oscillator mode
LP Oscillator mode
XT Oscillator mode
HS Oscillator mode
RC Oscillator mode
TCY = 4/FOSC
—
—
—
(1)
Oscillator Period
30.5
—
—
10,000
1,000
—
DC
—
—
—
∞
250
50
250
200
2
—
—
(1)
OS03
Instruction Cycle Time
TCY
—
OS04*
TOSH,
TOSL
External CLKIN High,
External CLKIN Low
LP oscillator
100
20
0
—
XT oscillator
—
HS oscillator
OS05*
TOSR,
TOSF
External CLKIN Rise,
External CLKIN Fall
—
LP oscillator
0
—
∞
∞
XT oscillator
0
—
HS oscillator
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing
code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current
consumption. All devices are tested to operate at “min” values with an external clock applied to OSC1 pin. When an
external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
DS41288C-page 150
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 15-2: OSCILLATOR PARAMETERS
Standard Operating Conditions (unless otherwise stated)
Operating Temperature
-40°C ≤ TA ≤ +125°C
Param
Sym
No.
Freq.
Tolerance
Characteristic
Min
Typ†
Max
Units
Conditions
OS06
TWARM
Internal Oscillator Switch
when running
—
—
—
2
TOSC Slowest clock
(3)
OS08
INTOSC
Internal Calibrated
INTOSC Frequency
1%
2%
7.92
7.84
8.0
8.0
8.08
8.16
MHz VDD = 3.5V, 25°C
(2)
MHz 2.5V ≤ VDD ≤ 5.5V,
0°C ≤ TA ≤ +85°C
5%
7.60
8.0
8.40
MHz 2.0V ≤ VDD ≤ 5.5V,
-40°C ≤ TA ≤ +85°C (Ind.),
-40°C ≤ TA ≤ +125°C (Ext.)
VDD = 2.0V, -40°C to +85°C
VDD = 3.0V, -40°C to +85°C
VDD = 5.0V, -40°C to +85°C
OS10*
TIOSC ST INTOSC Oscillator Wake-
up from Sleep
—
—
—
5.5
3.5
3
12
7
24
14
11
μs
μs
μs
Start-up Time
6
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing
code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected
current consumption. All devices are tested to operate at “min” values with an external clock applied to the OSC1 pin.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
2: To ensure these oscillator frequency tolerances, VDD and VSS must be capacitively decoupled as close to the device as
possible. 0.1 μF and 0.01 μF values in parallel are recommended.
3: By design.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 151
PIC16F610/616/16HV610/616
FIGURE 15-7:
CLKOUT AND I/O TIMING
Cycle
Write
Q4
Fetch
Q1
Read
Q2
Execute
Q3
FOSC
OS12
OS11
OS20
OS21
CLKOUT
OS19
OS13
OS18
OS16
OS17
I/O pin
(Input)
OS14
OS15
I/O pin
(Output)
New Value
Old Value
OS18, OS19
TABLE 15-3: CLKOUT AND I/O TIMING PARAMETERS
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C ≤ TA ≤ +125°C
Param
No.
Sym
Characteristic
Min
Typ† Max Units
Conditions
OS11
OS12
OS13
OS14
OS15
OS16
TOSH2CKL FOSC↑ to CLKOUT↓ (1)
TOSH2CKH FOSC↑ to CLKOUT↑ (1)
—
—
—
—
70
72
20
—
ns VDD = 5.0V
ns VDD = 5.0V
ns
—
—
—
50
—
TCKL2IOV
CLKOUT↓ to Port out valid(1)
TIOV2CKH Port input valid before CLKOUT↑(1)
TOSC + 200 ns
ns
TOSH2IOV FOSC↑ (Q1 cycle) to Port out valid
—
70*
—
ns VDD = 5.0V
ns VDD = 5.0V
TOSH2IOI
FOSC↑ (Q2 cycle) to Port input invalid
(I/O in hold time)
50
OS17
OS18
OS19
TIOV2OSH Port input valid to FOSC↑ (Q2 cycle)
20
—
—
ns
(I/O in setup time)
TIOR
TIOF
Port output rise time(2)
—
—
15
40
72
32
ns VDD = 2.0V
VDD = 5.0V
Port output fall time(2)
—
—
28
15
55
30
ns VDD = 2.0V
VDD = 5.0V
OS20* TINP
OS21* TRAP
INT pin input high or low time
25
—
—
—
—
ns
ns
PORTA interrupt-on-change new input
level time
TCY
*
These parameters are characterized but not tested.
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated.
†
Note 1: Measurements are taken in RC mode where CLKOUT output is 4 x TOSC.
2: Includes OSC2 in CLKOUT mode.
DS41288C-page 152
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
FIGURE 15-8:
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND
POWER-UP TIMER TIMING
VDD
MCLR
30
Internal
POR
33
PWRT
Time-out
32
OSC
Start-Up Time
(1)
Internal Reset
Watchdog Timer
(1)
Reset
31
34
34
I/O pins
Note 1:
Asserted low.
FIGURE 15-9:
BROWN-OUT RESET TIMING AND CHARACTERISTICS
VDD
VBOR + VHYST
VBOR
(Device in Brown-out Reset)
(Device not in Brown-out Reset)
37
Reset
(due to BOR)
33*
*
64 ms delay only if PWRTE bit in the Configuration Word register is programmed to ‘0’.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 153
PIC16F610/616/16HV610/616
TABLE 15-4: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER
AND BROWN-OUT RESET PARAMETERS
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C ≤ TA ≤ +125°C
Param
No.
Sym
TMCL
Characteristic
Min
Typ†
Max Units
Conditions
30
MCLR Pulse Width (low)
2
5
—
—
—
—
μs VDD = 5V, -40°C to +85°C
μs VDD = 5V, +85°C to +125°C
31
32
TWDT
TOST
Watchdog Timer Time-out
Period (No Prescaler)
7
TBD
18
18
33
TBD
ms VDD = 5V, -40°C to +85°C
ms VDD = 5V, +85°C to +125°C
Oscillation Start-up Timer
Period(1, 2)
—
1024
—
TOSC (NOTE 3)
33*
34*
TPWRT Power-up Timer Period
40
—
65
—
140
2.0
ms
TIOZ
I/O High-impedance from
MCLR Low or Watchdog Timer
Reset
μs
35*
36*
37*
VBOR
VHYST
TBOR
Brown-out Reset Voltage
TBD
—
2.1
50
—
TBD
—
V
(NOTE 4)
Brown-out Reset Hysteresis
mV
Brown-out Reset Minimum
Detection Period
100
—
μs VDD ≤ VBOR
Legend: TBD = To Be Determined
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits may result in an unstable oscillator oper-
ation and/or higher than expected current consumption. All devices are tested to operate at “min” values
with an external clock applied to the OSC1 pin. When an external clock input is used, the “max” cycle time
limit is “DC” (no clock) for all devices.
2: By design.
3: Period of the slower clock.
4: To ensure these voltage tolerances, VDD and VSS must be capacitively decoupled as close to the device as
possible. 0.1 μF and 0.01 μF values in parallel are recommended.
DS41288C-page 154
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
FIGURE 15-10:
TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
T0CKI
40
41
42
T1CKI
45
46
49
47
TMR0 or
TMR1
TABLE 15-5: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)
Operating Temperature
-40°C ≤ TA ≤ +125°C
Param
Sym
No.
Characteristic
Min
Typ†
Max
Units
Conditions
40*
41*
42*
TT0H
TT0L
TT0P
T0CKI High Pulse Width
No Prescaler
With Prescaler
No Prescaler
With Prescaler
0.5 TCY + 20
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
10
0.5 TCY + 20
10
T0CKI Low Pulse Width
T0CKI Period
Greater of:
20 or TCY + 40
N
ns N = prescale value
(2, 4, ..., 256)
45*
46*
47*
TT1H
TT1L
T1CKI High Synchronous, No Prescaler
0.5 TCY + 20
15
—
—
—
—
ns
ns
Time
Synchronous,
with Prescaler
Asynchronous
30
0.5 TCY + 20
15
—
—
—
—
—
—
ns
ns
ns
T1CKI Low Synchronous, No Prescaler
Time
Synchronous,
with Prescaler
Asynchronous
30
—
—
—
—
ns
TT1P
FT1
T1CKI Input Synchronous
Period
Greater of:
30 or TCY + 40
N
ns N = prescale value
(1, 2, 4, 8)
Asynchronous
60
—
—
—
—
ns
48
Timer1 Oscillator Input Frequency Range
(oscillator enabled by setting bit T1OSCEN)
32.768
kHz
49*
TCKEZTMR1 Delay from External Clock Edge to Timer
Increment
2 TOSC
—
7 TOSC
—
Timers in Sync
mode
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 155
PIC16F610/616/16HV610/616
FIGURE 15-11:
CAPTURE/COMPARE/PWM TIMINGS (ECCP)
CCP1
(Capture mode)
CC01
CC02
CC03
Note:
Refer to Figure 15-5 for load conditions.
TABLE 15-6: CAPTURE/COMPARE/PWM REQUIREMENTS (ECCP)
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C ≤ TA ≤ +125°C
Param
No.
Sym
Characteristic
Min
Typ† Max Units
Conditions
CC01* TccL
CC02* TccH
CC03* TccP
CCP1 Input Low Time
CCP1 Input High Time
CCP1 Input Period
No Prescaler
0.5TCY + 20
20
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
With Prescaler
No Prescaler
With Prescaler
0.5TCY + 20
20
3TCY + 40
N
ns N = prescale
value (1, 4 or
16)
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
DS41288C-page 156
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 15-7: COMPARATOR SPECIFICATIONS
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C ≤ TA ≤ +125°C
Param
No.
Sym
Characteristics
Min Typ†
Max
Units
Comments
CM01 VOS
CM02 VCM
CM03* CMRR
CM04* TRT
Input Offset Voltage
—
0
5.0
—
10
VDD – 1.5
—
mV (VDD - 1.5)/2
Input Common Mode Voltage
Common Mode Rejection Ratio
Response Time
V
+55
—
—
—
—
—
dB
Falling
Rising
150
200
—
600
ns
ns
(NOTE 1)
1000
10
CM05* TMC2COV Comparator Mode Change to Output Valid
CM06* VHYS Input Hysteresis Voltage
These parameters are characterized but not tested.
μs
45
—
mV
*
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: Response time is measured with one comparator input at (VDD - 1.5)/2 - 100 mV to (VDD - 1.5)/2 + 20 mV.
TABLE 15-8: COMPARATOR VOLTAGE REFERENCE (CVREF) SPECIFICATIONS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +125°C
Param
Sym
No.
Characteristics
Min
Typ†
Max
Units
Comments
CV01
CLSB
Step Size(2)
—
—
VDD/24
VDD/32
—
—
V
V
Low Range (VRR = 1)
High Range (VRR = 0)
CV02
CACC
Absolute Accuracy
—
—
—
—
1/2
1/2
LSb Low Range (VRR = 1)
LSb High Range (VRR = 0)
CV03
CV04
CR
Unit Resistor Value (R)
Settling Time(1)
—
—
2k
—
—
Ω
μs
CST
10
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
Note 1: Settling time measured while VRR = 1and VR<3:0> transitions from ‘0000’ to ‘1111’.
2: See Section 8.11 “Comparator Voltage Reference” for more information.
TABLE 15-9: VOLTAGE REFERENCE SPECIFICATIONS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +125°C
VR Voltage Reference Specifications
Param
No.
Symbol
Characteristics
Min
Typ
Max
Units
Comments
VR01
VR02
VR03
VP6OUT
V1P2OUT
TSTABLE
VP6 voltage output
V1P2 voltage output
Settling Time
0.55
1.1
—
0.6
1.200
10
0.65
1.3
—
V
V
μs
*
These parameters are characterized but not tested.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 157
PIC16F610/616/16HV610/616
TABLE 15-10: SHUNT REGULATOR SPECIFICATIONS (PIC16HV610/616 only)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +125°C
SHUNT REGULATOR CHARACTERISTICS
Param
No.
Symbol
Characteristics
Min
Typ
Max
Units
Comments
SR01
SR02
SR03*
SR04
VSHUNT Shunt Voltage
ISHUNT Shunt Current
TSETTLE Settling Time
4.75
4
5
5.25
50
V
—
—
—
mA
ns
—
150
10
To 1% of final value
CLOAD
Load Capacitance
0.01
μF
Bypass capacitor on VDD
pin
SR05
ΔISNT
Regulator operating current
—
—
180
μA
Includes band gap
reference current
*
These parameters are characterized but not tested.
TABLE 15-11: PIC16F616/16HV616 A/D CONVERTER (ADC) CHARACTERISTICS:
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +125°C
Param
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
AD01 NR
AD02 EIL
AD03 EDL
Resolution
—
—
—
—
10 bits
bit
Integral Error
—
—
1
1
LSb VREF = 5.12V
Differential Error
LSb No missing codes to 10 bits
VREF = 5.12V
AD04 EOFF Offset Error
AD07 EGN Gain Error
—
—
1.5
—
—
1
LSb VREF = 5.12V
LSb VREF = 5.12V
AD06 VREF Reference Voltage(3)
AD06A
2.2
2.5
—
—
VDD
V
Absolute minimum to ensure 1 LSb
accuracy
AD07 VAIN Full-Scale Range
VSS
—
—
—
VREF
10
V
AD08 ZAIN Recommended
Impedance of Analog
Voltage Source
kΩ
AD09* IREF
VREF Input Current(3)
10
—
—
—
1000
50
μA During VAIN acquisition.
Based on differential of VHOLD to VAIN.
μA During A/D conversion cycle.
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: Total Absolute Error includes integral, differential, offset and gain errors.
2: The A/D conversion result never decreases with an increase in the input voltage and has no missing
codes.
3: ADC VREF is from external VREF or VDD pin, whichever is selected as reference input.
4: When ADC is off, it will not consume any current other than leakage current. The power-down current
specification includes any such leakage from the ADC module.
DS41288C-page 158
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TABLE 15-12: PIC16F616/16HV616 A/D CONVERSION REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +125°C
Param
No.
Sym
Characteristic
A/D Clock Period
Min
Typ†
Max Units
Conditions
AD130* TAD
1.6
3.0
—
—
9.0
9.0
μs TOSC-based, VREF ≥ 3.0V
μs TOSC-based, VREF full range
A/D Internal RC
Oscillator Period
ADCS<1:0> = 11(ADRC mode)
μs At VDD = 2.5V
3.0
1.6
—
6.0
4.0
11
9.0
6.0
—
μs At VDD = 5.0V
AD131 TCNV Conversion Time
(not including
TAD Set GO/DONE bit to new data in A/D
Result register
Acquisition Time)(1)
AD132* TACQ Acquisition Time
11.5
—
—
5
μs
μs
—
AD133* TAMP Amplifier Settling Time
AD134 TGO Q4 to A/D Clock Start
—
—
TOSC/2
—
—
TOSC/2 + TCY
—
—
If the A/D clock source is selected as
RC, a time of TCY is added before the
A/D clock starts. This allows the SLEEP
instruction to be executed.
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: ADRESH and ADRESL registers may be read on the following TCY cycle.
2: See Section 9.3 “A/D Acquisition Requirements” for minimum conditions.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 159
PIC16F610/616/16HV610/616
FIGURE 15-12:
PIC16F616/16HV616 A/D CONVERSION TIMING (NORMAL MODE)
BSF ADCON0, GO
1 TCY
(1)
(TOSC/2
AD134
Q4
)
AD131
AD130
A/D CLK
9
8
7
6
3
2
1
0
A/D Data
ADRES
NEW_DATA
1 TCY
OLD_DATA
ADIF
GO
DONE
Sampling Stopped
AD132
Sample
Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the
SLEEPinstruction to be executed.
FIGURE 15-13:
PIC16F616/16HV616 A/D CONVERSION TIMING (SLEEP MODE)
BSF ADCON0, GO
AD134
Q4
(1)
(TOSC/2 + TCY
)
1 TCY
AD131
AD130
A/D CLK
A/D Data
9
8
7
3
2
1
0
6
NEW_DATA
1 TCY
OLD_DATA
ADRES
ADIF
GO
DONE
Sampling Stopped
AD132
Sample
Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the
SLEEPinstruction to be executed.
DS41288C-page 160
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
16.0 DC AND AC
CHARACTERISTICS GRAPHS
AND TABLES
Graphs are not available at this time.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 161
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 162
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
17.0 PACKAGING INFORMATION
17.1 Package Marking Information
14-Lead PDIP
Example
-I/P
PIC16F616
XXXXXXXXXXXXXX
XXXXXXXXXXXXXX
e
3
YYWWNNN
0610017
14-Lead SOIC (.150”)
Example
XXXXXXXXXXX
XXXXXXXXXXX
PIC16F616-E
0610017
YYWWNNN
14-Lead TSSOP
Example
XXXXXXXX
YYWW
XXXX/ST
0610
NNN
017
16-Lead QFN
Example
XXXXXXX
XXXXXXX
YYWWNNN
16F616
-I/ML
0610017
Legend: XX...X Customer-specific information
Y
Year code (last digit of calendar year)
YY
Year code (last 2 digits of calendar year)
WW
NNN
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
e
3
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
*
)
3
e
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
*
Standard PIC® device marking consists of Microchip part number, year code, week code, and traceability
code. For PIC® device marking beyond this, certain price adders apply. Please check with your
Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 163
PIC16F610/616/16HV610/616
17.2 Package Details
The following sections give the technical details of the packages.
8-Lead Plastic Dual In-Line (P or PA) – 300 mil Body [PDIP]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
N
NOTE 1
E1
3
1
2
D
E
A2
A
L
A1
c
e
eB
b1
b
Units
INCHES
Dimension Limits
MIN
NOM
8
MAX
Number of Pins
Pitch
N
e
.100 BSC
–
Top to Seating Plane
A
–
.210
.195
–
Molded Package Thickness
Base to Seating Plane
Shoulder to Shoulder Width
Molded Package Width
Overall Length
A2
A1
E
.115
.015
.290
.240
.348
.115
.008
.040
.014
–
.130
–
.310
.250
.365
.130
.010
.060
.018
–
.325
.280
.400
.150
.015
.070
.022
.430
E1
D
Tip to Seating Plane
Lead Thickness
L
c
Upper Lead Width
b1
b
Lower Lead Width
Overall Row Spacing §
eB
Notes:
1. Pin 1 visual index feature may vary, but must be located with the hatched area.
2. § Significant Characteristic.
3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing C04-018B
DS41288C-page 164
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
14-Lead Plastic Small Outline (SL or OD) – Narrow, 3.90 mm Body [SOIC]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
N
E
E1
NOTE 1
1
2
3
e
h
b
α
h
c
φ
A2
A
L
A1
β
L1
Units
MILLIMETERS
Dimension Limits
MIN
NOM
MAX
Number of Pins
Pitch
N
e
14
1.27 BSC
Overall Height
A
–
–
1.75
–
Molded Package Thickness
Standoff §
A2
A1
E
1.25
0.10
–
–
0.25
Overall Width
6.00 BSC
Molded Package Width
Overall Length
E1
D
h
3.90 BSC
8.65 BSC
Chamfer (optional)
Foot Length
0.25
0.40
–
0.50
1.27
L
–
Footprint
L1
φ
1.04 REF
Foot Angle
0°
0.17
0.31
5°
–
–
–
–
–
8°
Lead Thickness
Lead Width
c
0.25
0.51
15°
b
Mold Draft Angle Top
Mold Draft Angle Bottom
α
β
5°
15°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. § Significant Characteristic.
3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-065B
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 165
PIC16F610/616/16HV610/616
14-Lead Plastic Thin Shrink Small Outline (ST) – 4.4 mm Body [TSSOP]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
N
E
E1
NOTE 1
1
2
e
b
c
φ
A2
A
A1
L
L1
Units
MILLIMETERS
Dimension Limits
MIN
NOM
MAX
Number of Pins
Pitch
N
e
14
0.65 BSC
Overall Height
Molded Package Thickness
Standoff
A
–
–
1.20
1.05
0.15
A2
A1
E
0.80
0.05
1.00
–
Overall Width
Molded Package Width
Molded Package Length
Foot Length
6.40 BSC
E1
D
4.30
4.90
0.45
4.40
4.50
5.10
0.75
5.00
L
0.60
Footprint
L1
φ
1.00 REF
Foot Angle
0°
–
–
–
8°
Lead Thickness
Lead Width
c
0.09
0.20
0.30
b
0.19
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side.
3. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-087B
DS41288C-page 166
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
16-Lead Plastic Quad Flat, No Lead Package (ML) – 4x4x0.9 mm Body [QFN]
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
D2
EXPOSED
PAD
e
E
E2
2
1
2
b
1
K
N
N
NOTE 1
L
TOP VIEW
BOTTOM VIEW
A3
A
A1
Units
MILLIMETERS
Dimension Limits
MIN
NOM
16
MAX
Number of Pins
N
e
Pitch
0.65 BSC
0.90
Overall Height
Standoff
A
0.80
0.00
1.00
0.05
A1
A3
E
0.02
Contact Thickness
Overall Width
Exposed Pad Width
Overall Length
Exposed Pad Length
Contact Width
Contact Length
0.20 REF
4.00 BSC
2.65
E2
D
2.50
2.80
4.00 BSC
2.65
D2
b
2.50
0.25
0.30
0.20
2.80
0.35
0.50
–
0.30
L
0.40
Contact-to-Exposed Pad
K
–
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Package is saw singulated.
3. Dimensioning and tolerancing per ASME Y14.5M.
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-127B
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 167
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 168
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
APPENDIX A: DATA SHEET
APPENDIX B: MIGRATING FROM
REVISION HISTORY
OTHER PIC®
DEVICES
Revision A
This discusses some of the issues in migrating from
other PIC® devices to the PIC16F6XX Family of
devices.
This is a new data sheet.
Revision B (12/06)
Added PIC16F610/16HV610 parts.
Replaced Package Drawings.
Revision C (03/2007)
Replaced Package Drawings (Rev. AM); Replaced
Development Support Section; Revised Product ID
System.
B.1
PIC16F676 to PIC16F610/616/16HV610/616
FEATURE COMPARISON
Feature PIC16F676
20 MHz
TABLE B-1:
PIC16F610/16HV610
PIC16F616/16HV616
Max Operating Speed
Max Program Memory (Words)
SRAM (bytes)
20 MHz
20 MHz
1024
1024
2048
64
64
128
A/D Resolution
10-bit
None
10-bit
Timers (8/16-bit)
Oscillator Modes
Brown-out Reset
Internal Pull-ups
Interrupt-on-change
Comparator
1/1
1/1
2/1
8
8
8
Y
Y
Y
RA0/1/2/4/5
RA0/1/2/4/5, MCLR
RA0/1/2/4/5, MCLR
RA0/1/2/3/4/5
RA0/1/2/3/4/5
RA0/1/2/3/4/5
1
N
2
N
2
Y
ECCP
INTOSC Frequencies
Internal Shunt Regulator
4 MHz
N
8 MHz
8 MHz
Y (PIC16HV610)
Y (PIC16HV616)
Note: This device has been designed to perform
to the parameters of its data sheet. It has
been tested to an electrical specification
designed to determine its conformance
with these parameters. Due to process
differences in the manufacture of this
device, this device may have different
performance characteristics than its earlier
version. These differences may cause this
device to perform differently in your
application than the earlier version of this
device.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 169
PIC16F610/616/16HV610/616
NOTES:
DS41288C-page 170
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
INDEX
RC2 and RC3 Pins ..................................................... 41
RC4 Pin ...................................................................... 42
RC5 Pin ...................................................................... 42
A
A/D
Specifications.................................................... 158, 159
Resonator Operation .................................................. 27
Timer1 ........................................................................ 47
Timer2 ........................................................................ 53
TMR0/WDT Prescaler ................................................ 43
Watchdog Timer ....................................................... 119
Brown-out Reset (BOR).................................................... 110
Associated Registers................................................ 111
Specifications ........................................................... 154
Timing and Characteristics....................................... 153
Absolute Maximum Ratings .............................................. 139
AC Characteristics
Industrial and Extended ............................................ 150
Load Conditions........................................................ 149
ADC .................................................................................... 71
Acquisition Requirements ........................................... 79
Associated registers.................................................... 81
Block Diagram............................................................. 71
Calculating Acquisition Time....................................... 79
Channel Selection....................................................... 72
Configuration............................................................... 72
Configuring Interrupt ................................................... 74
Conversion Clock........................................................ 72
Conversion Procedure ................................................ 74
Internal Sampling Switch (RSS) Impedance................ 79
Interrupts..................................................................... 73
Operation .................................................................... 74
Operation During Sleep .............................................. 74
Port Configuration....................................................... 72
Reference Voltage (VREF)........................................... 72
Result Formatting........................................................ 73
Source Impedance...................................................... 79
Special Event Trigger.................................................. 74
Starting an A/D Conversion ........................................ 73
ADCON0 Register............................................................... 76
ADCON1 Register............................................................... 77
ADRESH Register (ADFM = 0)........................................... 78
ADRESH Register (ADFM = 1)........................................... 78
ADRESL Register (ADFM = 0)............................................ 78
ADRESL Register (ADFM = 1)............................................ 78
Analog-to-Digital Converter. See ADC
C
C Compilers
MPLAB C18.............................................................. 136
MPLAB C30.............................................................. 136
Calibration Bits.................................................................. 108
Capture Module. See Enhanced Capture/
Compare/PWM (ECCP)
Capture/Compare/PWM (CCP)
Associated registers w/ Capture/Compare/
PWM..................................................... 85, 87, 103
Capture Mode............................................................. 84
CCP1 Pin Configuration ............................................. 84
Compare Mode........................................................... 86
CCP1 Pin Configuration ..................................... 86
Software Interrupt Mode............................... 84, 86
Special Event Trigger......................................... 86
Timer1 Mode Selection................................. 84, 86
Prescaler .................................................................... 84
PWM Mode................................................................. 88
Duty Cycle .......................................................... 89
Effects of Reset.................................................. 90
Example PWM Frequencies and
ANSEL Register.................................................................. 32
Assembler
Resolutions, 20 MHz .................................. 89
Example PWM Frequencies and
MPASM Assembler................................................... 136
Resolutions, 8 MHz .................................... 89
Operation in Sleep Mode.................................... 90
Setup for Operation ............................................ 90
System Clock Frequency Changes .................... 90
PWM Period ............................................................... 89
Setup for PWM Operation .......................................... 90
CCP1CON (Enhanced) Register ........................................ 83
Clock Sources
External Modes........................................................... 26
EC ...................................................................... 26
HS ...................................................................... 27
LP....................................................................... 27
OST .................................................................... 26
RC ...................................................................... 28
XT....................................................................... 27
Internal Modes............................................................ 28
INTOSC.............................................................. 28
INTOSCIO .......................................................... 28
CM1CON0 Register............................................................ 60
CM2CON0 Register............................................................ 61
CM2CON1 Register............................................................ 63
Code Examples
B
Block Diagrams
(CCP) Capture Mode Operation ................................. 84
ADC ............................................................................ 71
ADC Transfer Function ............................................... 80
Analog Input Model............................................... 62, 80
CCP PWM................................................................... 88
Clock Source............................................................... 25
Comparator C1 ........................................................... 56
Comparator C2 ........................................................... 56
Compare ..................................................................... 86
Crystal Operation........................................................ 27
External RC Mode....................................................... 28
In-Circuit Serial Programming Connections.............. 123
Interrupt Logic........................................................... 116
MCLR Circuit............................................................. 109
On-Chip Reset Circuit............................................... 108
PIC16F610/16HV610.................................................... 7
PIC16F616/16HV616.................................................... 8
PWM (Enhanced)........................................................ 91
RA0 and RA1 Pins...................................................... 34
RA2 Pins..................................................................... 35
RA3 Pin....................................................................... 36
RA4 Pin....................................................................... 37
RA5 Pin....................................................................... 38
RC0 and RC1 Pins...................................................... 41
A/D Conversion .......................................................... 75
Assigning Prescaler to Timer0.................................... 44
Assigning Prescaler to WDT....................................... 44
Changing Between Capture Prescalers ..................... 84
Indirect Addressing..................................................... 22
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 171
PIC16F610/616/16HV610/616
Initializing PORTA.......................................................31
Initializing PORTC.......................................................40
Saving Status and W Registers in RAM ...................118
Code Protection ................................................................122
Comparator
Errata.................................................................................... 6
F
Firmware Instructions ....................................................... 125
Fuses. See Configuration Bits
C2OUT as T1 Gate .....................................................63
Operation ....................................................................55
Operation During Sleep ..............................................59
Response Time...........................................................57
Synchronizing COUT w/Timer1 ..................................63
Comparator Analog Input Connection Considerations........62
Comparator Hysteresis .......................................................64
Comparator Module ............................................................55
Associated registers....................................................65
C1 Output State Versus Input Conditions...................57
Comparator Voltage Reference (CVREF)
Response Time...........................................................57
Comparator Voltage Reference (CVREF) ............................68
Effects of a Reset........................................................59
Specifications............................................................157
Comparators
G
General Purpose Register File ........................................... 12
I
ID Locations...................................................................... 122
In-Circuit Debugger........................................................... 123
In-Circuit Serial Programming (ICSP)............................... 123
Indirect Addressing, INDF and FSR registers..................... 22
Instruction Format............................................................. 125
Instruction Set................................................................... 125
ADDLW..................................................................... 127
ADDWF..................................................................... 127
ANDLW..................................................................... 127
ANDWF..................................................................... 127
BCF .......................................................................... 127
BSF........................................................................... 127
BTFSC...................................................................... 127
BTFSS ...................................................................... 128
CALL......................................................................... 128
CLRF ........................................................................ 128
CLRW ....................................................................... 128
CLRWDT .................................................................. 128
COMF ....................................................................... 128
DECF........................................................................ 128
DECFSZ ................................................................... 129
GOTO ....................................................................... 129
INCF ......................................................................... 129
INCFSZ..................................................................... 129
IORLW...................................................................... 129
IORWF...................................................................... 129
MOVF ....................................................................... 130
MOVLW .................................................................... 130
MOVWF.................................................................... 130
NOP.......................................................................... 130
RETFIE..................................................................... 131
RETLW ..................................................................... 131
RETURN................................................................... 131
RLF........................................................................... 132
RRF .......................................................................... 132
SLEEP ...................................................................... 132
SUBLW..................................................................... 132
SUBWF..................................................................... 133
SWAPF..................................................................... 133
XORLW .................................................................... 133
XORWF .................................................................... 133
Summary Table ........................................................ 126
INTCON Register................................................................ 18
Internal Oscillator Block
C2OUT as T1 Gate .....................................................48
Effects of a Reset........................................................59
Specifications............................................................157
Compare Module. See Enhanced Capture/
Compare/PWM (ECCP)
CONFIG Register..............................................................107
Configuration Bits..............................................................106
CPU Features ...................................................................106
Customer Change Notification Service .............................175
Customer Notification Service...........................................175
Customer Support.............................................................175
D
Data Memory.......................................................................12
DC Characteristics
Extended and Industrial ............................................146
Industrial and Extended ............................................142
Development Support .......................................................135
Device Overview ...................................................................7
E
ECCP. See Enhanced Capture/Compare/PWM
ECCPAS Register.............................................................100
Effects of Reset
PWM mode .................................................................90
Electrical Specifications ....................................................139
Enhanced Capture/Compare/PWM.....................................83
Enhanced Capture/Compare/PWM (ECCP)
Enhanced PWM Mode ................................................91
Auto-Restart......................................................101
Auto-shutdown..................................................100
Direction Change in Full-Bridge Output Mode ....97
Full-Bridge Application........................................95
Full-Bridge Mode.................................................95
Half-Bridge Application .......................................94
Half-Bridge Application Examples.....................102
Half-Bridge Mode................................................94
Output Relationships (Active-High and
Active-Low) .................................................92
Output Relationships Diagram............................93
Programmable Dead Band Delay .....................102
Shoot-through Current ......................................102
Start-up Considerations ......................................99
Specifications............................................................156
Timer Resources.........................................................83
INTOSC
Specifications ........................................... 151, 152
Internal Sampling Switch (RSS) Impedance........................ 79
Internet Address ............................................................... 175
Interrupts........................................................................... 115
ADC ............................................................................ 74
Associated Registers................................................ 117
Context Saving ......................................................... 118
Interrupt-on-Change ................................................... 32
PORTA Interrupt-on-Change.................................... 116
RA2/INT.................................................................... 115
Timer0 ...................................................................... 116
DS41288C-page 172
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
TMR1 .......................................................................... 49
INTOSC Specifications ............................................. 151, 152
IOCA Register..................................................................... 33
ANSEL Register ................................................. 32
Interrupt-on-Change ........................................... 32
Weak Pull-Ups.................................................... 32
Associated registers ................................................... 39
Pin Descriptions and Diagrams .................................. 34
RA0............................................................................. 34
RA1............................................................................. 34
RA2............................................................................. 35
RA3............................................................................. 36
RA4............................................................................. 37
RA5............................................................................. 38
Specifications ........................................................... 152
PORTA Register................................................................. 31
PORTC ............................................................................... 40
Associated registers ................................................... 42
P1A/P1B/P1C/P1D.See Enhanced Capture/
Compare/PWM (ECCP)...................................... 40
Specifications ........................................................... 152
PORTC Register................................................................. 40
Power-Down Mode (Sleep)............................................... 121
Power-on Reset (POR)..................................................... 109
Power-up Timer (PWRT).................................................. 109
Specifications ........................................................... 154
Precision Internal Oscillator Parameters .......................... 152
Prescaler
L
Load Conditions................................................................ 149
M
MCLR................................................................................ 109
Internal...................................................................... 109
Memory Organization.......................................................... 11
Data ............................................................................ 12
Program ...................................................................... 11
Microchip Internet Web Site.............................................. 175
Migrating from other PIC Devices..................................... 169
MPLAB ASM30 Assembler, Linker, Librarian ................... 136
MPLAB ICD 2 In-Circuit Debugger ................................... 137
MPLAB ICE 2000 High-Performance Universal
In-Circuit Emulator .................................................... 137
MPLAB Integrated Development Environment Software .. 135
MPLAB PM3 Device Programmer .................................... 137
MPLAB REAL ICE In-Circuit Emulator System................. 137
MPLINK Object Linker/MPLIB Object Librarian ................ 136
O
OPCODE Field Descriptions............................................. 125
Operational Amplifier (OPA) Module
AC Specifications...................................................... 158
OPTION Register.......................................................... 17, 45
Oscillator
Shared WDT/Timer0................................................... 44
Switching Prescaler Assignment ................................ 44
Program Memory................................................................ 11
Map and Stack (PIC16F610/16HV610)...................... 11
Map and Stack (PIC16F616/16HV616)...................... 11
Programming, Device Instructions.................................... 125
PWM Mode. See Enhanced Capture/Compare/PWM........ 91
PWM1CON Register......................................................... 103
Associated registers.............................................. 29, 51
Oscillator Module ................................................................ 25
EC............................................................................... 25
HS............................................................................... 25
INTOSC ...................................................................... 25
INTOSCIO................................................................... 25
LP................................................................................ 25
RC............................................................................... 25
RCIO........................................................................... 25
XT ............................................................................... 25
Oscillator Parameters ....................................................... 151
Oscillator Specifications.................................................... 150
Oscillator Start-up Timer (OST)
R
Reader Response............................................................. 176
Read-Modify-Write Operations ......................................... 125
Registers
ADCON0 (ADC Control 0).......................................... 76
ADCON1 (ADC Control 1).......................................... 77
ADRESH (ADC Result High) with ADFM = 0) ............ 78
ADRESH (ADC Result High) with ADFM = 1) ............ 78
ADRESL (ADC Result Low) with ADFM = 0).............. 78
ADRESL (ADC Result Low) with ADFM = 1).............. 78
ANSEL (Analog Select) .............................................. 32
CCP1CON (Enhanced CCP1 Control) ....................... 83
CM1CON0 (C1 Control) ............................................. 60
CM2CON0 (C2 Control) ............................................. 61
CM2CON1 (C2 Control) ............................................. 63
CONFIG (Configuration Word) ................................. 107
Data Memory Map (PIC16F610/16HV610) ................ 13
Data Memory Map (PIC16F616/16HV616) ................ 13
ECCPAS (Enhanced CCP Auto-shutdown Control). 100
INTCON (Interrupt Control) ........................................ 18
IOCA (Interrupt-on-Change PORTA).......................... 33
OPTION_REG (OPTION)..................................... 17, 45
OSCTUNE (Oscillator Tuning).................................... 29
PCON (Power Control Register)................................. 21
PCON (Power Control)............................................. 111
PIE1 (Peripheral Interrupt Enable 1) .......................... 19
PIR1 (Peripheral Interrupt Register 1)........................ 20
PORTA ....................................................................... 31
PORTC....................................................................... 40
PWM1CON (Enhanced PWM Control)..................... 103
Reset Values ............................................................ 113
Reset Values (special registers)............................... 114
Specifications............................................................ 154
OSCTUNE Register............................................................ 29
P
P1A/P1B/P1C/P1D.See Enhanced Capture/
Compare/PWM (ECCP).............................................. 91
Packaging ......................................................................... 163
Marking ..................................................................... 163
PDIP Details.............................................................. 164
PCL and PCLATH............................................................... 22
Stack........................................................................... 22
PCON Register ........................................................... 21, 111
PICSTART Plus Development Programmer ..................... 138
PIE1 Register...................................................................... 19
Pin Diagram
PDIP, SOIC, TSSOP................................................. 2, 3
QFN .......................................................................... 4, 5
Pinout Descriptions
PIC16F610/16HV610.................................................... 9
PIC16F616/16HV616.................................................. 10
PIR1 Register...................................................................... 20
PORTA................................................................................ 31
Additional Pin Functions ............................................. 32
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 173
PIC16F610/616/16HV610/616
Special Function Registers .........................................12
Special Register Summary .........................................15
SRCON0 (SR Latch Control 0) ...................................67
SRCON1 (SR Latch Control 1) ...................................67
STATUS......................................................................16
T1CON........................................................................50
T2CON........................................................................54
TRISA (Tri-State PORTA)...........................................31
TRISC (Tri-State PORTC) ..........................................40
VRCON (Voltage Reference Control) .........................70
WPUA (Weak Pull Up PORTA)...................................33
Reset.................................................................................108
Revision History ................................................................169
A/D Conversion (Sleep Mode).................................. 160
Brown-out Reset (BOR)............................................ 153
Brown-out Reset Situations ...................................... 110
CLKOUT and I/O ...................................................... 152
Clock Timing............................................................. 150
Comparator Output..................................................... 55
Enhanced Capture/Compare/PWM (ECCP)............. 156
Full-Bridge PWM Output............................................. 96
Half-Bridge PWM Output .................................... 94, 102
INT Pin Interrupt ....................................................... 117
PWM Auto-shutdown
Auto-restart Enabled......................................... 101
Firmware Restart.............................................. 101
PWM Direction Change .............................................. 97
PWM Direction Change at Near 100% Duty Cycle..... 98
PWM Output (Active-High) ......................................... 92
PWM Output (Active-Low).......................................... 93
Reset, WDT, OST and Power-up Timer................... 153
Time-out Sequence
S
Shoot-through Current ......................................................102
Sleep
Power-Down Mode ...................................................121
Wake-up....................................................................121
Wake-up using Interrupts..........................................121
Software Simulator (MPLAB SIM).....................................136
Special Event Trigger..........................................................74
Special Function Registers .................................................12
SRCON0 Register...............................................................67
SRCON1 Register...............................................................67
STATUS Register................................................................16
Case 1 .............................................................. 112
Case 2 .............................................................. 112
Case 3 .............................................................. 112
Timer0 and Timer1 External Clock ........................... 155
Timer1 Incrementing Edge ......................................... 49
Wake-up from Interrupt............................................. 122
Timing Parameter Symbology .......................................... 149
TRISA ................................................................................. 31
TRISA Register................................................................... 31
TRISC................................................................................. 40
TRISC Register................................................................... 40
T
T1CON Register..................................................................50
T2CON Register..................................................................54
Thermal Considerations....................................................148
Time-out Sequence...........................................................111
Timer0.................................................................................43
Associated Registers ..................................................45
External Clock.............................................................44
Interrupt.......................................................................45
Operation ....................................................................43
Specifications............................................................155
T0CKI..........................................................................44
Timer1.................................................................................47
Associated registers....................................................51
Asynchronous Counter Mode .....................................48
Reading and Writing ...........................................48
Interrupt.......................................................................49
Modes of Operation ....................................................47
Operation ....................................................................47
Operation During Sleep ..............................................49
Oscillator.....................................................................48
Prescaler.....................................................................48
Specifications............................................................155
Timer1 Gate
V
Voltage Reference (VR)
Specifications ........................................................... 157
Voltage Reference. See Comparator Voltage
Reference (CVREF)
Voltage References
Associated registers ................................................... 65
VP6 Stabilization ........................................................ 69
VREF. SEE ADC Reference Voltage
W
Wake-up Using Interrupts................................................. 121
Watchdog Timer (WDT).................................................... 119
Associated registers ................................................. 120
Specifications ........................................................... 154
WPUA Register................................................................... 33
WWW Address ................................................................. 175
WWW, On-Line Support ....................................................... 6
Inverting Gate .....................................................48
Selecting Source...........................................48, 63
SR Latch .............................................................66
Synchronizing COUT w/Timer1 ..........................63
TMR1H Register .........................................................47
TMR1L Register..........................................................47
Timer2
Associated registers....................................................54
Timers
Timer1
T1CON................................................................50
Timer2
T2CON................................................................54
Timing Diagrams
A/D Conversion.........................................................160
DS41288C-page 174
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Distributor or Representative
• Local Sales Office
• Field Application Engineer (FAE)
• Technical Support
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• Development Systems Information Line
Customers
should
contact
their
distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
Technical support is available through the web site
at: http://support.microchip.com
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com, click on Customer Change
Notification and follow the registration instructions.
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 175
PIC16F610/616/16HV610/616
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip prod-
uct. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
To:
Technical Publications Manager
Reader Response
Total Pages Sent ________
RE:
From:
Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
PIC16F610/616/16HV610/616
DS41288C
Literature Number:
Device:
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS41288C-page 176
Preliminary
© 2007 Microchip Technology Inc.
PIC16F610/616/16HV610/616
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
X
/XX
XXX
Examples:
Temperature
Range
Package
Pattern
a)
PIC16F610/616/16HV610/616-E/P
301
=
Extended Temp., PDIP package, 20 MHz, QTP
pattern #301
b)
PIC16F610/616/16HV610/616-I/SL = Industrial
Temp., SOIC package, 20 MHz
Device:
PIC16F610/616/16HV610/616, PIC16F610/616/16HV610/
616T(1)
Temperature
Range:
I
E
=
=
-40°C to +85°C (Industrial)
-40°C to +125°C (Extended)
Package:
ML
P
SL
ST
=
Quad Flat No Leads (QFN)
Plastic DIP
14-lead Small Outline (3.90 mm)
Thin Shrink Small Outline (4.4 mm)
=
=
=
Note 1:
T
=
in tape and reel TSSOP and SOIC
packages only.
Pattern:
QTP, SQTP or ROM Code; Special Requirements
(blank otherwise)
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 177
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Habour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Korea - Gumi
Tel: 82-54-473-4301
Fax: 82-54-473-4302
Boston
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Seoul
China - Fuzhou
Tel: 86-591-8750-3506
Fax: 86-591-8750-3521
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Malaysia - Penang
Tel: 60-4-646-8870
Fax: 60-4-646-5086
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
China - Shunde
Tel: 86-757-2839-5507
Fax: 86-757-2839-5571
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
China - Xian
Tel: 86-29-8833-7250
Fax: 86-29-8833-7256
12/08/06
DS41288C-page 178
Preliminary
© 2007 Microchip Technology Inc.
相关型号:
PIC16HV785
20-Pin Flash-Based, 8-Bit CMOS Microcontroller with Two-Phase Asynchronous Feedback PWM Dual High-Speed Comparators and Dual Operational Amplifiers
MICROCHIP
PIC16HV785-E/ML
20-Pin Flash-Based, 8-Bit CMOS Microcontroller with Two-Phase Asynchronous Feedback PWM Dual High-Speed Comparators and Dual Operational Amplifiers
MICROCHIP
PIC16HV785-E/P
20-Pin Flash-Based, 8-Bit CMOS Microcontroller with Two-Phase Asynchronous Feedback PWM Dual High-Speed Comparators and Dual Operational Amplifiers
MICROCHIP
©2020 ICPDF网 联系我们和版权申明