PL502-39QC [MICROCHIP]
IC VCXO 800MHZ 16QFN;型号: | PL502-39QC |
厂家: | MICROCHIP |
描述: | IC VCXO 800MHZ 16QFN 石英晶振 压控振荡器 |
文件: | 总10页 (文件大小:455K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise ICs
PIN CONFIGURATION
(Top View)
FEATURES
Selectable 750kHz to 800MHz range
Low phase noise output (@ 10kHz frequency off-
set, -142dBc/Hz for 19.44MHz, -125dBc/Hz for
155.52MHz, -115dBc/Hz for 622.08MHz)
LVCMOS (PL502-37), LVPECL (PL502-35 and
PL502-38) or LVDS (PL502-39) output
12MHz to 25MHz crystal input
1
6
1
5
1
4
1
3
1
2
1
1
1
0
VDD
XIN
1
2
3
4
5
6
7
8
SEL0^
SEL1^
GND
XOUT
SEL3^
SEL2^
OE
CLKC
VDD
CLKT
GND
No external load capacitor or varicap required.
Output Enable selector
VCON
GND
Wide pull range (±200 ppm)
9
GND
Selectable /16 to x32 frequency divider/multiplier
3.3V operation
TSSOP-16L
^: Internal pull-up
*: On 3x3 package, PL502-35/-38 do not have SEL0 available: Pin 10
is VDD, pin 11 is GND. However, PL502-37/-39 have SEL0 (pin 10),
and pin11 is VDD. See pin assignment table for details.
Available in 16-Pin TSSOP or 16-pin 3x3mm QFN
GREEN/RoHS compliant packages
DESCRIPTION
The PL502-35 (LVPECL with inverted OE), PL502-37
(LVCMOS), PL502-38 (LVPECL), and PL502-39
(LVDS) are high performance and low phase noise
VCXO IC chips. They provide phase noise perfor-
mance as low as –125dBc at 10kHz offset (at
155MHz), by multiplying the input crystal frequency up
to 32x. The wide pull range (±200 ppm) and very low
jitter make them ideal for a wide range of applications,
including SONET/SDH and FEC. They accept funda-
mental parallel resonant mode crystals from 12MHz to
25MHz.
12
11
10
9
13
14
15
8
7
6
5
XOUT
GND
CLKC
VDD
SEL3^
SEL2^
PL502-3x
16
CLKT
OE
1
2
3
4
QFN-16L
OUTPUT ENABLE LOGICAL LEVELS
BLOCK DIAGRAM
Part #
OE
State
SEL[3:0]
0 (Default) Output enabled
PL502-38
1
0
Tri-state
Tri-state
OE
PLL
PL502-35
PL502-37
PL502-39
CLKC
Oscillator
Amplifier
w/
integrated
varicaps
(Phase
Locked
Loop)
VCON
1 (Default) Output enabled
CLKT
XIN
OE input: Logical states defined by LVPECL levels for PL502-38
Logical states defined by LVCMOS levels for PL502-37/-39
XOUT
PLL by-pass
PL502-3x
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944-0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/15/13 Page 1
PL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise ICs
FREQUENCY SELECTION TABLE
SEL3
SEL2
SEL1
SEL0
Selected Multiplier
0
0
0
1
1
1
1
1
1
1
0
1
1
0
0
0
1
1
1
1
1
1
1
0
1
1
0
0
1
1
1
0
1
1
0
1
0
1
0
1
Fin x 32
Fin / 8
Fin x 2
Fin / 2
Fin / 16
Fin x 4
Fin / 4
Fin x 8
Fin x 16
No multiplication
Note: SEL0 is not available (always “1”) for PL502-35 and PL502-38 in 3x3mm package
PIN DESCRIPTIONS PL502-35 and PL502-38 (see next page for PL502-37/-39)
TSSOP
Pin number
3x3mm QFN
Pin number
Name
Type
Description
XIN
2
12
I
I
Crystal input (See Crystal Specification on page 4)
Crystal output (See Crystal Specification on page 4)
Output enable pin (See OE logic state table on page 1)
Voltage Control input
XOUT
OE
3
13
6
16
I
VCON
GND
CLKT
CLKC
SEL0
SEL1
SEL2
SEL3
VDD
7
1
I
8,9,10,14
2,3,4,8,11
P
O
O
I
Ground connection
11
13
16
15
5
5
LVPECL True output
7
LVPECL Complementary output
Not available
Multiplier selector pins. These pins have an internal pull-
up that will default SEL to ‘1’ when not connected to
GND.
9
15
I
I
4
14
I
1, 12
6,10
P
+3.3V power supply.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944-0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/15/13 Page 2
PL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise ICs
PIN DESCRIPTIONS PL502-37/-39 (see previous page for PL502-35/-38)
TSSOP
Pin number
3x3mm QFN
Pin number
Name
Type
Description
XIN
XOUT
OE
2
12
13
I
I
Crystal input. See Crystal Specification on page 4.
Crystal output. See Crystal Specification on page 4.
Output enable pin (see OE logic state table on page 1).
Voltage Control input.
3
6
7
16
I
VCON
GND
1
I
8,9,10,14
2,3,4,8
P
Ground.
LVDS True output for PL502-39
No Connect for PL502-37
CLKT
CLKC
11
13
5
7
O
O
LVDS Complementary output for PL502-39
LVCMOS out for PL502-37
SEL0
SEL1
SEL2
SEL3
VDD
16
15
10
9
I
I
Multiplier selector pins. These pins have an internal pull-
up that will default SELx to ‘1’ when not connected to
GND.
5
15
I
4
14
I
1, 12
6,11
P
+3.3V power supply.
ELECTRICAL SPECIFICATIONS
1. Absolute Maximum Ratings
PARAMETERS
SYMBOL
MIN.
MAX.
UNITS
Supply Voltage
VDD
VI
4.6
VDD+0.5
VDD+0.5
150
V
Input Voltage, dc
-0.5
-0.5
-65
V
Output Voltage, dc
VO
TS
TA
TJ
V
Storage Temperature
C
C
C
C
kV
Ambient Operating Temperature*
Junction Temperature
-40
85
125
Lead Temperature (soldering, 10s)
ESD Protection, Human Body Model
260
2.5
Exposure of the device under conditions beyond the limits specified by Maximum R atings for extended periods may cause permanent damage to the
device and affect product reliability. These conditions represent a stress rating only, and functional operations of the dev ice at these or any other
conditions above the operational limits noted in this specification is not implied.
* Note: Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade on ly.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944-0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/15/13 Page 3
PL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise ICs
2. Crystal Specifications
PARAMETERS
SYMBOL
CONDITIONS
MIN.
TYP.
MAX. UNITS
Crystal Resonator Frequency
Crystal Loading Rating
Crystal Pullability
FXIN
Parallel Fundamental Mode
At VCON = 1.65V
12
25
MHz
pF
-
CL (xtal)
9.5
C0/C1 (xtal) AT cut
RE AT cut
250
30
Recommended ESR
Ω
Note: Crystal Loading rating: 9.5pF is the loading the crystal sees from the VCXO chip at VCON = 1.65V. It is assumed that the cr ystal will be at nom-
inal frequency at this load. If the crystal requires more load to be at nominal frequency, the additiona l load must be added externally. This however
may reduce the pull range.
3. Voltage Control Crystal Oscillator
PARAMETERS
SYMBOL
CONDITIONS
MIN.
TYP.
MAX. UNITS
VCXO Stabilization Time *
TVCXOSTB From power valid
10
ms
FXIN = 12 – 25MHz;
XTAL C0/C1 < 250
0V VCON 3.3V
VCXO Tuning Range
500
150
ppm
CLK output pullability
ppm
ppm/V
%
VCON=1.65V, 1.65V
200
VCXO Tuning Characteristic
Pull range linearity
10
VCON pin input impedance
VCON modulation BW
2000
10
kΩ
kHz
0V VCON 3.3V, -3dB
Note: Parameters denoted with an asterisk (*) represent nominal characterization data and are not production tested to any specific limits.
4. General Electrical Specifications
PARAMETERS
SYMBOL
CONDITIONS
MIN.
TYP.
MAX. UNITS
FOUT <24MHz
60/28/15
Supply Current,
Dynamic (with
Loaded Outputs)
LVPECL/LVDS/
IDD
24MHz< FOUT <96MHz
96MHz< FOUT <800MHz
65/45/30 mA
100/80/40
LVCMOS
Operating
Voltage
VDD
2.97
3.63
V
@ 50% VDD (LVCMOS)
@ 1.25V (LVDS)
@ VDD – 1.3V (LVPECL)
45
45
45
50
50
50
55
55
55
Output Clock Du-
ty Cycle
%
Short Circuit
Current
mA
50
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944-0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/15/13 Page 4
PL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise ICs
5. Jitter Specifications
PARAMETERS
CONDITIONS
FREQUENCY
MIN.
TYP.
MAX. UNITS
19.44MHz
77.76MHz
155.52MHz
622.08MHz
19.44MHz
77.76MHz
155.52MHz
622.08MHz
155.52MHz
622.08MHz
2.2
4.5
4.5
5.0
17
With capacitive decoupling
between VDD and GND.
Over 10,000 cycles.
Period jitter RMS
ps
With capacitive decoupling
between VDD and GND.
Over 10,000 cycles.
25
Period jitter
Peak-to-Peak
ps
27
35
2.5
2.5
4
Integrated jitter RMS
Integrated 12kHz to 20MHz
ps
4
6. Phase Noise Specifications
PARAMETERS
FREQUENCY
@10Hz
@100Hz
@1kHz
@10kHz
@100kHz UNITS
19.44MHz
77.76MHz
155.52MHz
622.08MHz
-80
-72
-65
-55
-108
-103
-95
-132
-122
-120
-109
-142
-130
-125
-115
-150
-125
Phase Noise relative
to carrier (typical)
dBc/Hz
-121
-85
-110
Note: Phase Noise measured at VCON = 0V
7. LVCMOS Electrical Characteristics
PARAMETERS
SYMBOL
CONDITIONS
MIN.
TYP.
MAX. UNITS
IOH
IOL
VOH= VDD-0.4V, VDD=3.3V
VOL = 0.4V, VDD = 3.3V
10
10
mA
mA
ns
Output drive current
Output Clock Rise/Fall Time
0.3V ~ 3.0V with 15 pF load
2.4
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944-0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/15/13 Page 5
PL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise ICs
8. LVDS Electrical Characteristics
PARAMETERS
SYMBOL
CONDITIONS
MIN.
TYP.
MAX. UNITS
Output Differential Voltage
VDD Magnitude Change
Output High Voltage
Output Low Voltage
Offset Voltage
VOD
VOD
VOH
247
-50
355
454
50
mV
mV
V
1.4
1.1
1.2
3
1.6
RL = 100Ω
(see figure)
VOL
0.9
1.125
0
V
VOS
1.375
25
V
Offset Magnitude Change
mV
VOS
Vout = VDD or GND
VDD = 0V
Power-off Leakage
IOXD
IOSD
uA
1
10
Output Short Circuit Current
-5.7
-8
mA
9. LVDS Switching Characteristics
PARAMETERS
SYMBOL
CONDITIONS
MIN.
TYP.
MAX. UNITS
RL = 100Ω
CL = 10 pF
(see figure)
Differential Clock Rise Time
Differential Clock Fall Time
tr
tf
0.2
0.2
0.7
0.7
1.0
1.0
ns
ns
LVDS Lev els Test Circuit
LVDS Switching Test Circuit
OUT
OUT
CL = 10pF
50
50
VOD
VOS
VDIFF
RL = 100
CL = 10pF
OUT
OUT
LVDS Transistion Time Wav ef orm
OUT
OUT
0V (Differential)
80%
80%
VDIFF
0V
20%
20%
tR
tF
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944-0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/15/13 Page 6
PL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise ICs
10. LVPECL Electrical Characteristics
PARAMETERS
SYMBOL
CONDITIONS
MIN.
MAX.
UNITS
Output High Voltage
Output Low Voltage
VOH
VOL
VDD – 1.025
V
V
RL = 50Ω to (VDD – 2V)
(see figure)
VDD – 1.620
11. LVPECL Switching Characteristics
PARAMETERS
Clock Rise Time
Clock Fall Time
SYMBOL
CONDITIONS
MIN.
TYP.
MAX. UNITS
tr
tf
0.6
0.6
1.5
1.5
ns
ns
20%~80% of Waveform
LVPECL Levels Test Circuit
LVPECL Output Skew
OUT
VDD
OUT
50?
50?
2.0V
50%
OUT
tSKEW
OUT
LVPECL Transistion Time Waveform
DUTY CYCLE
45 - 55%
55 - 45%
OUT
80%
50%
20%
OUT
tR
tF
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944-0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/15/13 Page 7
PL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise ICs
PACKAGE INFORMATION (GREEN PACKAGE COMPLIANT)
TSSOP-16L
Dimension in MM
Symbol
Min.
-
Max.
1.20
0.15
0.30
0.20
5.10
4.50
6.60
0.75
E
H
A
A1
b
C
D
E
0.05
0.19
0.09
4.90
4.30
6.20
0.45
D
H
L
A
A1
C
e
0.65 BSC
L
B
e
QFN-16L
e
DDD
L
Dimension (mm)
Symbol
D1
Min
Nom
0.75
Max
A
A1
A3
b
0.70
0.00
0.80
0.05
-
0.203
0.25
0.20
2.95
2.95
1.65
1.65
0.250
0.30
3.05
3.05
1.75
1.75
0.350
Pin1 Dot
b
D
3.00
E
3.00
A
D1
E1
L
1.70
1.70
0.300
0.50BSC
A3
e
SEATING
PLANE
A1
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944-0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/15/13 Page 8
PL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise ICs
ORDERING INFORMATION
For part ordering, please contact our Sales Department:
2180 Fortune Drive, San Jose, CA 95131, USA
Tel: (408) 944-0800 Fax: (408) 474-1000
PART NUMBER
The order number for this device is a combination of the following:
Part number, Package type, Operating temperature range, shipping method
PL502-3x X X -X
Part Number
None=Tube
R=Tape & Reel
Package Type
O=TSSOP-16L
Q=QFN-16L
Temperature
C=Commercial (0°C to 70°C)
I=Industrial (-40°C to 85°C)
Marking**
Part/Order Number*
Package Option
Commercial
Industrial
P502-35
OC
LLLLL
P502
35
P502-35
OI
LLLLL
P502
35I
PL502-35OC
8-pin TSSOP-16L – (Tube)
PL502-35OC-R
8-pin TSSOP-16L – (Tape and Reel)
PL502-35QC-R
16-pin QFN-16L - (Tape and Reel)
LLL
LLL
P502-37
OC
LLLLL
P502
37
P502-37
OI
LLLLL
P502
37I
PL502-37OC
8-pin TSSOP-16L – (Tube)
PL502-37OC-R
8-pin TSSOP-16L – (Tape and Reel)
PL502-37QC-R
16-pin QFN-16L - (Tape and Reel)
LLL
LLL
P502-38
OC
LLLLL
P502
38
P502-38
OI
LLLLL
P502
38I
PL502-38OC
8-pin TSSOP-16L – (Tube)
PL502-38OC-R
8-pin TSSOP-16L – (Tape and Reel)
PL502-38QC-R
16-pin QFN-16L - (Tape and Reel)
LLL
LLL
P502-39
OC
LLLLL
P502
39
P502-39
OI
LLLLL
P502
39I
PL502-39OC
8-pin TSSOP-16L – (Tube)
PL502-39OC-R
8-pin TSSOP-16L – (Tape and Reel)
PL502-39QC-R
16-pin QFN-16L - (Tape and Reel)
LLL
LLL
*Note: For Industrial use “I” instead of “C” in the Part/Order number.
**Note: “LLL” or “LLLLL” are designates lot number
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944-0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/15/13 Page 9
PL502-35/-37/-38/-39
750kHz – 800MHz Low Phase Noise Multiplier VCXO
Universal Low Phase Noise ICs
Micrel Inc., reserves the right to make changes in its products or specifications, or both at any time without notice. The in formation furnished by Micrel
is believed to be accurate and reliable. However, Micrel makes no guarantee or warranty co ncerning the accuracy of said information and shall not be
responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product.
LIFE SUPPORT POLICY: Micrel’s products are not authorized for use as critical components in life support devices or systems without the express
written approval of the President of Micrel Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944-0800 • fax +1(408) 474-1000 • www.micrel.com Rev 4/15/13 Page 10
相关型号:
©2020 ICPDF网 联系我们和版权申明