SY88927ZGTR [MICROCHIP]
LINE RECEIVER, PDSO8, 3 MM, MSOP-8;型号: | SY88927ZGTR |
厂家: | MICROCHIP |
描述: | LINE RECEIVER, PDSO8, 3 MM, MSOP-8 光电二极管 |
文件: | 总6页 (文件大小:66K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
5V/3.3V 2.5Gbps
HIGH-SPEED DIFFERENTIAL RECEIVER
SY88927V
FEATURES
DESCRIPTION
■ 3.3V and 5V power supply options
■ Maximum frequency > 3.0GHz
The SY88927V is a 2.5Gbps high-speed differential
receiver. The device is functionally equivalent to the
EL16V devices, with higher performance capabilities. With
output transition times significantly faster than the EL16V,
the SY88927V is ideally suited for interfacing with high-
frequency sources.
■ Internal 75KΩ input pull-down resistors
■ Faster version of SY100EL16V
■ 100K ECL compatible I/O
The SY88927V provides a V output for either single-
ended use or as a DC bias for AC coupling to the device.
■ Improved output waveform characteristics
■ Available in 8-pin (3mm) MSOP and SOIC package
BB
The V
pin should be used only as a bias for the
BB
SY88927V as its current sink/source capability is limited.
Whenever used, the V pin should be bypassed to the
BB
most positive supply via a 0.01µF capacitor.
Under open input conditions (pulled to V ), internal
EE
input clamps will force the Q output LOW.
PIN NAMES
Pin
Function
D
Data Inputs
Q
Data Outputs
VBB
Reference Voltage Output
Rev.: E
Amendment: /0
M9999-092305
hbwhelp@micrel.com or (408) 955-1690
1
Issue Date: September2005
SY88927V
Micrel, Inc.
PACKAGE/ORDERING INFORMATION
Ordering Information
Package
Type
Operating
Range
Package
Marking
Lead
Finish
NC
D
1
2
3
4
8
7
6
5
VCC
Q
Part Number
SY88927VKC
SY88927VKCTR(1)
K8-1
K8-1
Z8-1
Z8-1
K8-1
Commercial
Commercial
Commercial
Commercial
Industrial
927V
927V
927V
927V
Sn-Pb
Sn-Pb
Sn-Pb
Sn-Pb
/D
/Q
SY88927VZC
VBB
VEE
SY88927VZCTR(1)
SY88927VKG(2)
927V with
Pb-Free bar-line indicator
Pb-Free
NiPdAu
10-Pin MSOP (K10-1)
SY88927VKGTR(1,2)
SY88927VZG(2)
K8-1
Z8-1
Z8-1
Industrial
Industrial
Industrial
927V with
Pb-Free bar-line indicator
Pb-Free
NiPdAu
927V with
Pb-Free bar-line indicator
Pb-Free
NiPdAu
SY88927VZGTR(1,2)
927V with
Pb-Free bar-line indicator
Pb-Free
NiPdAu
Note:
1. Tape and Reel.
2. NiPdAu Pb-Free package recommended for new designs.
M9999-092305
hbwhelp@micrel.com or (408) 955-1690
2
SY88927V
Micrel, Inc.
(1)
ABSOLUTE MAXIMUM RATINGS
Symbol
VEE
Rating
Value
Unit
V
Power Supply Voltage
Input Voltage
–8.0 to 0
0 to –6.0
VI
V
IOUT
Output Current
–Continuous
–Surge
50
100
mA
TA
Operating Temperature Range
–40 to +85
+260
°C
°C
°C
TLEAD
Tstore
Lead Temperature (Soldering, 20 sec.)
Storage Temperature Range
–65 to +150
Note:
1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at
conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods
may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
V
= –3.0V to –5.5V; V = GND
CC
EE
TA = –40°C
TA = 0°C
TA = +25°C
TA = +85°C
Symbol
IEE
Parameter
Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit
Power Supply Current
—
—
40
—
—
40
—
35
42
—
—
48
mA
V
VBB
Output Reference
Voltage
–1.38 –1.30 –1.26 –1.38 –1.31 –1.26 –1.38 –1.32 –1.26 –1.38 –1.33 –1.26
IIH
Input HIGH Current
—
—
150
—
—
150
—
—
150
—
—
150
µA
(1)
100K SERIES DC ELECTRICAL CHARACTERISTICS
V
= –3.0V to –5.5V; V = GND
EE
CC
TA = –40°C
TA = 0°C to +85°C
Symbol
Parameter
Min.
Typ.
Max.
Min.
Typ.
Max.
Unit
Conditions
VOH
VOL
Output HIGH Voltage
Output LOW Voltage
–1085 –1005 –880
–1830 –1695 –1555 –1810 –1705 –1620
–1025 –955
–880
mV
VIN = VIH(Max)
or VIL(Min)
Loading with
50Ω to –2.0V
VOHA
VOLA
Output HIGH Voltage
Output LOW Voltage
–1095
—
—
—
—
–1555
–1035
—
—
—
—
–1610
mV
VIN = VIH(Min)
or VIL(Max)
VIH
VIL
Input HIGH Voltage(2) –1165
—
—
—
–880
–1165
—
—
—
–880
–1475
—
mV
mV
µA
Input LOW Voltage(3)
Input LOW Current
–1810
0.5
–1475 –1810
0.5
IIL
—
VIN = VIL(Min)
Notes:
1. This table replaces the three tables traditionally seen in ECL 100K data books. Outputs are terminated through a 50Ω resistor to –2.0V except where
otherwise specified on the individual data sheets.
2. Guaranteed HIGH Signal for all inputs.
3. Guaranteed LOW Signal for all inputs.
M9999-092305
hbwhelp@micrel.com or (408) 955-1690
3
SY88927V
Micrel, Inc.
AC ELECTRICAL CHARACTERISTICS
V
= –3.0V to –5.5V; V = GND
CC
EE
TA = –40°C
TA = 0°C
TA = +25°C
TA = +85°C
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Typ.
Max.
Min.
Max.
Unit
tPLH
tPHL
Propagation Delay to
Output
ps
D (Diff)
D (SE)
150
—
240
—
150
—
240
—
150
—
190
—
240
—
150
—
280
—
tskew
VCMR
VPP
Duty Cycle Skew(1)
(Diff)
—
VEE+2
150
—
—
20
—
5
20
—
20
ps
V
Common Mode Range(2)
V
–0.4 VEE+2
V
–0.4 VEE+2
—
V
–0.4 VEE+2
V
–0.4
CC
CC
CC
CC
Input Voltage Range
(Diff)
1200
175
150
—
1200
175
150
—
800
105
1200
175
150
—
1200
175
mV
ps
tr
tf
Output Rise/Fall Times Q(3)
(20% to 80%)
—
NOTES:
1. Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device.
2. TheCMRrangeisreferencedtothemostpositivesideofthedifferentialinputsignal. NormaloperationisobtainediftheHIGHlevelfallswithinthespecified
range and the peak-to-peak voltage lies between VPP min. and 1V. The lower end of the CMR range varies 1:1 with VEE
.
3. VID > 150mV.
M9999-092305
hbwhelp@micrel.com or (408) 955-1690
4
SY88927V
Micrel, Inc.
8 LEAD MSOP (K8-1)
Rev. 01
M9999-092305
hbwhelp@micrel.com or (408) 955-1690
5
SY88927V
Micrel, Inc.
8 LEAD SOIC .150" WIDE (Z8-1)
Rev. 03
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB http://www.micrel.com
The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use.
Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can
reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into
the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s
use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify
Micrel for any damages resulting from such use or sale.
© 2005 Micrel, Incorporated.
M9999-092305
hbwhelp@micrel.com or (408) 955-1690
6
相关型号:
©2020 ICPDF网 联系我们和版权申明