WRB4812YT-3W [MICRODC]
3W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC/DC CONVERTER; 3W ,宽电压输入,隔离稳压单路输出DC / DC转换器型号: | WRB4812YT-3W |
厂家: | MICRODC POWER TECHNOLOGY CO., LTD |
描述: | 3W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC/DC CONVERTER |
文件: | 总3页 (文件大小:463K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
WRB-YT-3W Series
3W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC/DC CONVERTER
SELECTION GUIDE
Input
Output
Efficiency
(%,Typ.)
Voltage
(VDC)
Current(MA)
order code
Voltage(VDC)
Range
Nominal
Max*
Max.
Min.
5
600
250
200
600
250
200
600
250
200
FEATURES
◆Efficiency up to 81%
WRB1205YT-3W
WRB1212YT-3W
WRB1215YT-3W
WRB2405YT-3W
WRB2412YT-3W
WRB2415YT-3W
WRB4805YT-3W
WRB4812YT-3W
WRB4815YT-3W
12
12
12
24
24
24
48
48
48
9-18
9-18
20
20
20
40
40
40
80
80
80
60
25
20
60
25
20
60
25
20
75
78
79
76
80
80
77
80
81
12
15
5
9-18
◆Operating temperature: -40°C ~ +85°C
◆1500VDC isolation
18-36
18-36
18-36
36-72
36-72
36-72
12
15
5
◆UL94V-0 package material
◆No external component required
◆Industry standard pinout
◆MTBF>1,000,000 hours
◆ RoHS Compliance
12
15
* Input voltage can not exceed this value, or will cause the permanent damage.
MODEL SELECTION
⑥
①
②
③
④
⑤
WRB 12 05 Y T -3W
①Product Series
③Output Voltage
⑤Package Style
②Input Voltage
④Wide (2:1) Input Range
⑥Rated Power
COMMON SPECIFICATIONS
Item
Test conditions
Min.
Typ.
Max.
Units
%
Storage humidity
Operating temperature
95
85
-40
-55
℃
DESCRIPTION
125
℃
Storage temperature
Temp. Rise at full load
The WRB_YT-3W series are specially designed for
applications where a wide range input voltage power
supplies are isolated from the input power supply in a
distributed power supply system on a circuit board.
These products apply to:
15
℃
1.5mm from case for 10 seconds
300
℃
Lead temperature
Cooling
Free air convection
1) Where the voltage of the input power supply is wide
range (voltage range ≤2:1);
Continuous, automatic recovery
Epoxy Resin (UL94-V0)
Short circuit protection
Case material
MTBF
2) Where isolation is necessary between input and output
(Isolation Voltage ≤1500VDC);
3) Where the regulation of the output voltage and the
output ripple noise are demanded.
1000
k hours
11
g
Weight
MICRODC reserves the copyright
http://www.microdc.cn
Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646
Page 1 of 3
WRB-YT-3W Series
TYPICAL CHARACTERISTICS
ISOLATION SPECIFICATIONS
Item
Test Conditions
Min.
Typ.
Max.
Units
Isolation voltage
Tested for 1 minute and 1mA max
Test at 500VDC
1500
1000
VDC
MΩ
pF
Isolation resistance
Isolation capacitance
Input/Output, 100KHz/1V
100
*Supply voltage must be discontinued at the end of short circuit duration.
OUTPUT SPECIFICATIONS
Item
Output power
Test Conditions
Min.
Typ.
Max.
Units
Refer to products program
Refer to recommended circuit
From 10% to 100% load
0.3
3
W
%
Output voltage accuracy
Load regulation
±1
±3
±0.1
±0.2
±1
%
Line regulation
Input voltage from low to high
Refer to recommended circuit
20MHz Bandwidth
±0.5
±0.03
100
%
Temperature drift (Vout)
Ripple & noise*
%/℃
mVp-p
kHz
50
Switching frequency
100% load, input voltage range
300
*Test ripple and noise by “parallel cable”method . See detailed operation instructions at Testing of
ower Converter section , application notes.
*Supply voltage must be discontinued at the end of short circuit duration.
RECOMMENDED CIRCUIT
APPLICATION NOTE
1) Requirement On Output Load
In order to ensure the product operate efficiently and reliably, in addition to a max load (namely full
load), a minimum load is specified for this kind of DC/DC converter. Make sure the specified range of
input voltage is not exceeded, the minimum output load no less than 10% load. If the actual load is less
than the specified minimum load, the output ripple may increase sharply while its efficiency and reliability
will reduce greatly. If the actual output power is very small, please add an appropriate resistor as extra
loading, or contact our company for other lower output power products.
2) Recommended Circuit
All the WRB_YT-3W series have been tested according to the following recommended testing circuit
before leaving factory. This series should be tested under load (See Figure 1).
If you want to further decrease the input/output ripple, you can increase capacitance properly or
choose capacitors with low ESR. However, the capacitance of the output filter capacitor must be proper.
If the capacitance is too big, a startup problem might arise. For every channel of output, provided the
safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1).
General:
Cin:
12V
100µF
24V&48V
10µF-47µF
Cout: 10µF/100mA
3) Input Current
When it is used in unregulated power supply, be sure that the fluctuating range of the power supply
and the rippled voltage do not exceed the module standard. Input current of power supply should afford
the flash startup current of this kind of DC/DC module (Figure 2)
Output External Capacitor Table (Table 1)
Single Vout
Cout
(VDC)
(μF)
General: Ip ≤1..4*Iin-max
5
1000
470
12
15
4) No parallel connection or plug and play
330
http://www.microdc.cn
Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646
Page 2 of 3
WRB-YT-3W Series
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT
TUBE OUTLINE DIMENSIONS
FOOTPRINT DETAILS
Pin
Function
2,3
GND
+Vo
0V
14
16
22,23
Vin
Others
NC
NC: No connection
Note:
Unit:mm[inch]
Pin section tolerances:±0.10mm[±0.004inch]
General tolerances:±0.25mm[±0.010inch]
Note:
1. The load shouldn't be less than 10%, otherwise ripple will increase dramatically.
2. Operation under 10% load will not damage the converter; However, they may not meet all specification listed.
3. Capacitor MAX load tested at input voltage range and full load.
4. All specifications measured at Ta=25℃, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
5. Only typical models listed, other models may be different, please contact our technical person for more details.
6. In this datasheet, all the test methods of indications are based on corporate standards.
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646 E-mail:tech@microdc.cn
Website:http://www.microdc.cn
REACH COMPLIANT INFORMATION
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
http://www.microdc.cn
Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646
Page 3 of 3
相关型号:
WRB4812ZD-1W5
1.5W, WIDE INPUT, ISOLATED®ULATED SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZD-3W
3W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZD-4W
4W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZD-5W
5W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZD-6W
6W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZD-8W
8W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZHD-3W
3W, WIDE INPUT, ISOLATED & REGULATED DUAL/SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZHD-6W
6W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZLS-2W
Wide Input,Isolated&Regulated Single Output SIP-9(10) DC/DC ConverterWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZMD-10W
10W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZMD-12W
12W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
WRB4812ZMD-20W
20W, WIDE INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
MICRODC
©2020 ICPDF网 联系我们和版权申明