7R016FLA211I15_技术文档

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

PCMCIA Flash Memory Card

1 MEGABYTE through 40 MEGABYTE (Intel/Sharp based)

ARCHITECTURE OVERVIEW

FEATURES

WEDC’s FLA series is designed to support from 2 to 20,

4Mb, 8Mb or 16Mb components, providing a wide range

of density options. Cards are based on the 28F008SA

(8Mb) for 12V VPP applications or on the 28F004S5

(4Mb), 28F008S5 (8Mb) and 28F016S5 (16Mb) devices

for 5V only applications. Devices codes for the 28F004S5,

28F008SA, 28F008S5 and the 28F016S5 are: A7H,

A2H, A6H and AAh respectively. Systems should be

able to recognize all four codes. Cards utilizing the 8Mb

components provide densities ranging from 2MB to 20MB

in 2MB increments, cards utilizing 16Mb components

provide densities ranging from 4MB to 40MB in 4MB

increments. 4 Mbit memory devices are used only for

smallest capacity cards (1MB).

ꢀ

Low cost High Density Linear Flash Card

Supports 5V only systems or 5V systems with

12V VPP

ꢀ

Based on Intel/Sharp FlashFile Components

Fast Read Performance

- 150ns or 200ns Maximum Access Time

x8 / x16 Data Interface

ꢀ

High Performance Random Writes

- 8µs Typical Word Write Time

ꢀ

Automated Write and Erase Algorithms

- Command User Interface

In support of the PC Card 95 standard for word wide

access devices are paired. Therefore, the Flash array is

structured in 64K word (128kBytes) blocks. Write, read

and block erase operations can be performed as either

a word or byte wide operation . By multiplexing A0, CE1#

and CE2,# 8-bit hosts can access all data on data lines

DQ0-DQ7.

ꢀ

100,000 Erase Cycles per Block

64K word symmetrical Block Architecture

PC Card Standard Type I Form Factor

GENERAL DESCRIPTION

WEDC’s FLASeries Flash memory cards offer high density

linear Flash solid state storage solutions for code and data

storage, high performance disk emulation and execute

in place (XIP) applications in mobile PC and dedicated

(embedded) equipment.

The FLA21-FLA36 series also supports the following

PCMCIAcompatible register functions: Soft Reset via the

Conﬁguration Option Register, Power Down (sleep mode)

via the Conﬁguration and Status Register and monitoring

of Ready/Busy, Soft Reset and Power Down via the Card

Status Register (cards without attribute memory and

versions FLA51 - FLA66 do not have registers).

FLA series cards conform to PCMCIA international

standard.

The card’s control logic provides the system interface

and controls the internal Flash memories. Card can be

read/written in byte-wide or word-wide mode which allows

for ﬂexible integration into various systems. Combined

with ﬁle management software, such as Flash Translation

Layer (FTL), FLA Flash cards provide removable high-

performance disk emulation.

The FLAseries cards conform with the PC Card Standard

(PCMCIA) and JEIDA, providing electrical and physical

compatibility. The PC Card form factor offers an industry

standard pinout and mechanical outline, allowing density

upgrades without system design changes.

WEDC’s standard cards are shipped with WEDC’s Logo.

Cards are also available with blank housings (no Logo).

The blank housings are available in both a recessed

(for label) and flat housing. Please contact WEDC

sales representative for further information on Custom

artwork.

The FLA series offers low power modes controlled by

registers. Standard cards contain separate 2kB EEPROM

memory for Card Information Structure (CIS) which can be

used for easy identiﬁcation of card characteristics.

The WEDC FLA series is based on Intel/Sharp Flash

memories.

Note: Standard options include attribute memory. Cards without attribute memory are

available. Cards are also available with or without a hardware write protect switch.

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

1

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

BLOCK DIAGRAM

Device Pair (N/2 - 1)

CSn

Device (N-1)

Device (N-2)

Array

Address

Bus

ADDRESS

BUFFER

ADDRESS BUS

A1-A25

Control

Address

Bus

M Res

WE#

OE#

WL#

RL#

WH#

RH#

Control Logic

PCMCIA Interface

CE2#

CE1#

Cn

C0

CSn

Device Pair 1

REG#

A0

WP

Device 2

Device 0

Device 3

Device 1

CS1

CS0

At/Reg enable

Ctrl

SR Clr

Reg C;r

/SR

/PD

CS0

Device Pair 0

Card

Management

Registers

4000h

0000h

V^CC

RL#

WL#

RH#

WH#

DATA

BUS

Q8-Q15

DATA

BUS

Q0-Q7

VCC

attrib. mem

CIS

EEPROM 2kB

control

Q0-Q7

VCC

I/O buffer

DATA

BUS

D0-D7

DATA

BUS

D8-D15

Device type

28F004S5

28F008SA

28F008S5

28F016S5

Manuf ID

89H

Device ID

A7H

89H

A2H

89H

A6H

89H

AAH

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

2

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

REGISTERS IN ATTRIBUTE MEMORY SPACE*

CSR

CONFIGURATION STATUS REGISTER: ADRS =

4002H WRITE ONLY

ADDRESS

4100h

REGISTER NAME

Status Register

4002h

4000h

Conﬁg. and Status Register

Conﬁguration Option Register

Not Supported

PDwn Not Supported

D7

D6

D5

D4

D3

D2

D1

D0

*Cards without Att. Mem and FLA51- FLA66 do not have

registers

D2

Power Down, active High

1 = Place all memory devices in power down mode

0 = Normal Operation Power On

default = 0

COR

CONFIGURATION OPTION REGISTER: ADRS =

4000H WRITE ONLY

SR

SRES

D7

LREQ

D6

Conﬁguration Index

STATUS REGISTER: ADRS = 4100H

READ ONLY

D5

D4

D3

D2

D1

D0

D7

Soft Reset, active High

1 = Reset State

Not Supported SReset

PDwn Not Supported R/BSY

D7

D6

D5

D4

D3

D2

D1

D0

D5

Represents the state of SRESET bit in COR (4000h)

1 = Reset

0 = End Reset State

Level Req (not supported)

D6

0 = Normal Operation

D5-D0 Conﬁguration index (not supported)

Power On default D5 = 0

D3

Represents the state of Power Down bit (D2) in CSR

(4002h)

1 = Power Down

D0

by

Reﬂects the card's Ready/Busy signal (pin 16) driven

memory components Ready/

Busy outputs. This bit allows

card's Ready/Busy status.

software polling of the

1 = Ready

MECHANICAL

Interconnect area

1.6mm + 0.05

(0.063”)

3.0mm MIN

10.0mm MIN

(0.400”)

1.0mm + 0.05

(0.039”)

Substrate area

54.0mm + 0.10

(2.126”)

85.6mm + 0.20

(3.370”)

1.0mm + 0.05

(0.039”)

10.0mm MIN

(0.400”)

3.3mm + T1 (0.130”)

T1=0.10mm unterconnect area

T1=0.20mm substrate area

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

3

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

PINOUT

1

Signal name

GND

DQ3

DQ⁴

DQ⁵

DQ6

DQ7

CE^1#

A¹⁰

I/O

Function

Ground

Active

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

Signal name

GND

CD1#

DQ^11#

DQ¹²

DQ¹³

DQ¹⁴

DQ15

CE²

I/O

Function

Ground

Active

2

I/O

Data bit 3

O

I/O

I

Card Detect 1

LOW

3

I/O

Data bit 4

Data bit 11

4

I/O

Data bit 5

Data bit 12

I/O

Data bit 6

5

6

Data bit 13

I/O

Data bit 7

Data bit 14

7

I

Card enable 1

Address bit 10

Output enable

Address bit 11

Address bit 9

Address bit 8

Address bit 13

Address bit 14

Write Enable

Ready/Busy

Supply Voltage

Prog. Voltage

Address bit 16

Address bit 15

Address bit 12

Address bit 7

Address bit 6

Address bit 5

Address bit 4

Address bit 3

Address bit 2

Address bit 1

Address bit 0

Data bit 0

LOW

Data bit 15

8

I

Card Enable 2

Voltage Sense 1

Reserved

LOW

NC

9

OE#

A¹¹

I

VS^1#

RFU

A¹⁷

O

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

Notes:

I

A⁹

I

Reserved

A⁸

I

Address bit 17

Address bit 18

Address bit 19

Address bit 20

Address bit 21

Supply Voltage

Prog. Voltage

Address bit 22

Address bit 23

Address bit 24

Address bit 25

Voltage Sense 2

Card Reset

A¹³

I

A¹⁸

A¹⁴

I

A¹⁹

WE#

RDY/BSY#

V^CC

V^PP1

A¹⁶

LOW

I

O

A²⁰

2MB(3)

4MB(3)

LOW (4)

A²¹

VCC

NC

V^PP2

A²²

NC

I

8MB(3)

16MB(3)

32MB(3)

64MB(3)

NC

A¹⁵

I

A²³

A12

I

A24

I

A⁷

I

A²⁵

I

A⁶

I

VS2

O

I

A⁵

I

RST

Wait

RFU#

REG

BVD^2#

BVD¹

DQ⁸

HIGH (4)

Low(2,4)

A⁴

I

O

Extended Bus cycle

Reserved

A3

A²

I

Attrib Mem Select

Bat. Volt. Detect 2

Bat. Volt. Detect 1

Data bit 8

A¹

I

(2)

O

A⁰

I

DQ⁰

DQ1

DQ2

WP

I/O

O

I/O

O

Data bit 1

Data bit 2

DQ⁹

Data bit 9

DQ¹⁰

CD²

Data bit 10

Write Potect

Ground

HIGH

O

Card Detect 2

Ground

LOW

GND

GND#

1. RDY/BSY signal is an “Open drain” type output, pull-up resistor on host side is required.

2. Wait#, BVD¹and BVD2 are driven high for compatibility.

3. Shows density for which speciﬁed address bit is MSB. Higher order address bits are no connects

(ie 4MB A21 is MSB A22 - A25 are NC).

4. NC - No Connection for FLA51 - FLA66.

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

4

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

CARD SIGNAL DESCRIPTION

Symbol

Type

Name and Function

A0 - A25

INPUT

ADDRESS INPUTS: A0 through A25 enable direct addressing of up to 64MB of memory on the card. Signal A0 is not

used in word access mode. A25 is the most signiﬁcant bit

DQ0 - DQ15 INPUT/OUTPUT DATA INPUT/OUTPUT: DQ0 THROUGH DQ15 constitute the bi-directional databus. DQ15 is the MSB.

CE1#, CE2#

INPUT

CARD ENABLE 1 AND 2: CE1# enables even byte accesses, CE2# enables odd byte accesses. Multiplexing A0, CE1#

and CE2# allows 8-bit hosts to access all data on DQ0 - DQ7.

OE#

WE#

INPUT

OUTPUT ENABLE: Active low signal gating read data from the memory card.

WRITE ENABLE: Active low signal gating write data to the memory card.

RDY/

BSY#(*)

OUTPUT

READY/BUSY OUTPUT: Indicates status of internally timed erase or program algorithms. A high output indicates that

the card is ready to accept accesses. A low output indicates that one or more devices in the memory card are busy with

internally timed erase or write activities.

CD1#, CD2#

WP

OUTPUT

CARD DETECT 1 and 2: Provide card insertion detection. These signals are internally connected to ground on the card.

The host shall monitor these signals to detect card insertion (pulled-up on host side).

WRITE PROTECT: Write protect reﬂects the status of the Write Protect switch on the memory card. WP set to high =

write protected, providing internal hardware write lockout to the Flash array.If card does not include optional write protect

switch, this signal will be pulled low internally indicating write protect = “off”.

V^PP1, VPP2

V^CC

N.C.

PROGRAM/ERASE POWER SUPPLY: Provides programming voltages for card (12V). Not connected for 5V only card.

CARD POWER SUPPLY: (5.0V).

CARD GROUND

GND

REG#

INPUT

ATTRIBUTE MEMORY SELECT : Active low signal, enables access to Attribute Memory Plane, occupied by Card

Information Structure and Card Registers.

RST(*)

RESET: Active high signal for placing card in Power-on default state. Reset can be used as a Power-Down signal for the

memory array.

WAIT#(*)

BVD1, BVD2

VS1, VS2

RFU

OUTPUT

WAIT: This signal is pulled high internally for compatibility. No wait states are generated.

BATTERY VOLTAGE DETECT: These signals are pulled high to maintain SRAM card compatibility.

VOLTAGE SENSE: Notiﬁes the host socket of the card’s V^CCrequirements. VS1 and VS2 are open to indicate a 5V card .

RESERVED FOR FUTURE USE

NC

NO INTERNAL CONNECTION TO CARD: pin may be driven or left ﬂoating

(*) Signals not supported by FLA51-66 (N.C)

FUNCTIONAL TRUTH TABLE

READ function

Function Mode

Common Memory

Attribute Memory

D15-D8

CE2#

H

CE1#

H

A0

X

L

OE#

X

WE#

X

REG#

X

D15-D8

D7-D0

REG#

D7-D0

Standby Mode

Byte Access (8 bits)

High-Z

X

L

High-Z

H

L

H

High-Z

Even-Byte

Odd-Byte

Even-Byte

High-Z

Even-Byte

Not Valid

Even-Byte

High-Z

H

L

H

X

L

H

Word Access (16 bits)

Odd-Byte Only Access

WRITE function

L

H

Odd-Byte

Not Valid

L

H

L

H

Standby Mode

H

L

H

L

X

L

X

H

X

L

X

H

X

L

X

Byte Access (8 bits)

X

Even-Byte

Odd-Byte

Even-Byte

X

Even-Byte

L

H

X

Even-Byte

X

Word Access (16 bits)

Odd-Byte Only Access

L

Odd-Byte

L

H

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

5

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

ABSOLUTE MAXIMUM RATINGS ⁽¹⁾

Operating Temperature TA (ambient)

Commercial

0°C to +60 °C

Industrial

-40°C to +85 °C

Storage Temperature

Commercial

0°C to +60 °C

-40°C to +85 °C

-0.5V to VCC+0.5V

-0.5V to +7.0V

Industrial

Voltage on any pin relative to V^SS

VCC supply Voltage relative to VSS

Note:

(1) Stress greater than those listed under “Absolute Maximum ratings” may cause permanent damage to the device.

This is a stress rating only and functional operation at these or any other conditions greater than those

indicated in the operational sections of this speciﬁcation is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect reliability.

DC CHARACTERISTICS ⁽¹⁾

Symbol

Parameter

Density(Mbytes)

Notes

Typ⁽³⁾

Max

Units Test Conditions

ICCR

VCC Read Current

All

35

mA

VCC = VCCmax

tcycle = 150ns,CMOS levels

I^CCW

VCC Program Current

All

28F008S5

28F016S5

75

I^CCW

IPPW

ICCE

VCC Program Current

VPP Program Current

VCC Erase Current

All

28F008SA

Vpp=12V

30

mA

µA

All

100

230

I^CCS

(CMOS)

VCC Standby Current

2MB

20MB

2MB

20MB

4MB

40MB

2

110

900

600

420

60

V_CC= VCCmax

Control Signals = V_CC

Reset = V_SS, CMOS levels

28F008SA

2

28F008S5

2

28F016S5

380

CMOS Test Conditions: VCC = 5V ± 5%, VIL = VSS ± 0.2V, VIH = VCC ± 0.2V

Notes:

1. All currents are RMS values unless otherwise speciﬁed. I^CCR, ICCW and ICCE are based on Byte wide operations. For 16 bit operation values are double.

2. Control Signals: CE^1#, CE2#, OE#, WE#, REG#.

3. Typical: V^CC= 5V, T = +25C.

Symbol

Parameter

Notes

Min

Max

Units

Test Conditions

I^LI

Input Leakage Current

1

±20

µA

VCC = VCCMAX

VIN =VCC or VSS

ILO

Output Leakage Current

1

±20

µA

VCC = VCCMAX

VOUT =VCC or VSS

VIL

VIH

Input Low Voltage

Input High Voltage

1

0

0.8

VCC+0.5

0.4

V

0.7VCC

VOL

V^OH

V^LKO

Output Low Voltage

IOL = 3.2mA

IOH = -2.0mA

Output High Voltage

VCC-0.4

2.0

VCC

VCC Erase/Program Lock Voltage

Notes:

1. Values are the same for byte and word wide modes for all card densities.

2. Exceptions: Leakage currents on CE1, CE2, OE, REG and WE will be < 500 µA when V^IN= GND due to internal pull-up resistors. Leakage currents on RST will be <150µA when

V^IN=VCC due to internal pull-down resistor.

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

6

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

AC CHARACTERISTICS - READ TIMING PARAMETERS

SYMBOL (PCMCIA)

Parameter

150ns

Min

Max

Unit

ns

tC(R)

tA(A)

Read Cycle Time

Address Access Time

150

75

20

0

t^A(CE)

tA(OE)

tSU(A)

Card Enable Access Time

Output Enable Access Time

Address Setup Time

t^SU(CE)

t^H(A)

Card Enable Setup Time

Address Hold Time

20

0

t^H(CE)

t^V(A)

Card Enable Hold Time

Output Hold from Address Change

Output Disable Time from CE#

Output Disable Time from OE#

Output Enable Time from CE#

Output Enable Time from OE#

Power Down recovery to Output Delay. VCC = 5V

tDIS(CE)

tDIS(OE)

t^EN(CE)

tEN(OE)

tREC(RSR)

75

5

500

Note: AC timing diagrams and characteristics are guaranteed to meet or exceed PCMCIA 2.1 speciﬁcations.

READ TIMING DIAGRAM

tC(R)

tH(A)

tA(A)

A[25::0], REG#

tV

(A)

tA(CE)

tSU(CE)

CE1#, CE2#

NOTE 1

tH(CE)

tA(OE)

tSU(A)

tDIS(CE)

OE#

tEN(OE)

tDIS(OE)

D[15::0]

DATA VALID

Note: Signal may be high or low in this area.

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

7

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

AC CHARACTERISTICS - WRITE TIMING PARAMETERS

150ns

SYMBOL (PCMCIA)

Parameter

Unit

Min

150

80

Max

t^CW

tW(WE)

Write Cycle Time

Write Pulse Width

ns

t^SU(A)

Address Setup Time

20

t^SU(A-WEH)

tSU(CE-WEH)

tSU(D-WEH)

t^H(D)

Address Setup Time for WE#

Card Enable Setup Time for WE#

Data Setup Time for WE#

Data Hold Time

100

50

20

tREC(WE)

t^DIS(WE)

t^DIS(OE)

Write Recover Time

20

Output Disable Time from WE#

Output Disable Time from OE#

Output Enable Time from WE#

Output Enable Time from OE#

Output Enable Setup from WE#

Output Enable Hold from WE#

Card Enable Setup Time from OE#

75

tEN(WE)

5

t^EN(OE)

tSU(OE-WE)

tH(OE-WE)

t^SU(CE)

10

0

Note: AC timing diagrams and characteristics are guaranteed to meet or exceed PCMCIA 2.1 speciﬁcations.

WRITE TIMING DIAGRAM

tC(W)

A[25::0], REG#

t

SU(A-WEH)

SU(CE-WEH)

SU(CE)

t

REC(WE)

t

H(CE)

t

CE1#, CE2#

NOTE 1

OE#

WE#

tH(OE-WE)

t

SU(A)

tW(WE)

tH(D)

t

SU(OE-WE)

tSU(D-WEH)

NOTE 2

D[15::0](DIN

)

DATA INPUT

tDIS(WE)

tEN(OE)

tDIS(OE)

tEN(WE)

NOTE 2

D[15::0](DOUT

)

Note:

1.

2.

Signal may be high or low in this area.

When the data I/O pins are in the output state, no signals shall be applied to the data pins (D15-D0) by the host system.

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

8

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

DATA WRITE AND ERASE PERFORMANCE ^(1,3)

V_CC= 5V ± 5%, TA = 0C TO + 70C

Symbol

tWHQV1

tEHQV1

Parameter

Word/Byte Program time

Notes

4

Min

Typ⁽¹⁾

8

Max

Units

µs

tWHQV2

t^EHQV2

Block Program Time

Block Erase Time

device SA

device S5

device SA

0.6

0.5

1.6

2.1

10

sec

0.4

sec

Notes:

1. Typical: Nominal voltages and T^A= 25C.

2. Excludes system overhead.

3. Valid for all speed options.

4. To maximize system performance RDY/BSY# signal should be polled.

PRODUCT MARKING

EDI

WED 7P016FLA6200C15 C995 9915

COMPANY NAME

PART NUMBER

LOT CODE/TRACE NUMBER

DATE CODE

Note:

Some products are currently marked with our pre-merger company name/acronym (EDI). During our

transition period, some products will also be marked with our new company name/acronym (WED).

Starting October 2000 all PCMCIA products will be marked only with the WED preﬁx.

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

9

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

PART NUMBERING

7 P 016 FLA62 00 C 15

CARD TECHNOLOGY

7

8

FLASH

SRAM

PC CARD

P

R

Standard PCMCIA

Ruggedized PCMCIA

CARD CAPACITY

016

16MB

CARD FAMILY AND VERSION

- See Card Family and Version Info. for details (next page)

PACKAGING OPTION

00

Standard, type 1

TEMPERATURE RANGE

C

I

=

Commercial

Industrial -40°C to +85°C

0°C to +70°C

CARD ACCESS TIME

15

25

150ns

250ns

FLA30 With Attribute Memory, no Write Protect

FLA31 No Attribute Memory, with Write Protect

FLA32 With Attribute Memory, with Write Protect

Example P/N 7P004FLA3000C15

CARD FAMILY AND VERSION

INFORMATION

FLA21-FLA24

for programming and erase functions)

FLA21 No Attribute Memory, no Write Protect

Based on 28F008SA (requires 12V VPP

FLA33-FLA36

Based on 28F004S5 for 5V only

applications

FLA22 With Attribute Memory, no Write Protect

FLA23 No Attribute Memory, with Write Protect

FLA24 With Attribute Memory, with Write Protect

FLA33 No Attribute Memory, no Write Protect

FLA34 With Attribute Memory, no Write Protect

FLA35 No Attribute Memory, with Write Protect

Example P/N

7P004FLA2200C15

FLA36

With Attribute Memory, with Write Protect

7P004FLA3600C15

Example P/N

FLA25-FLA28

Based on 28F008S5 for 5V only

applications

FLA25 No Attribute Memory, no Write Protect

FLA26 With Attribute Memory, no Write Protect

FLA27 No Attribute Memory, with Write Protect

FLA28 With Attribute Memory, with Write Protect

FLA51-FLA54

Based on 28F008SA; the same as

FLA21-FLA24 with exception:

- no registers

- signals RST, RDY/BSY, Wait are not connected

FLA51 No Attribute Memory, no Write

FLA52 With Attribute Memory, no Write

FLA53 No Attribute Memory, with Write

Example P/N

7P004FLA2600C15

Protect

FLA29-FLA32

Based on 28F016S5 for 5V only

applications

FLA29 No Attribute Memory, no Write Protect

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

10

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

Protect

FLA60 With Attribute Memory, no Write

FLA61 No Attribute Memory, with Write

FLA62 With Attribute Memory, with

Protect

FLA54 With Attribute Memory, with Write Protect

Example P/N

7P004FLA5200C15

Protect

FLA55-FLA58

Based on 28F008S5; the same as FLA25-

FLA28 with exception:

Write Protect

- no registers

Example P/N

7P004FLA6000C15

- signals RST, RDY/BSY, Wait are not connected

FLA55 No Attribute Memory, no Write Protect

FLA56 With Attribute Memory, no Write Protect

FLA57 No Attribute Memory, with Write Protect

FLA58 With Attribute Memory, with Write Protect

FLA63-FLA66

Based on 28F004S5; the same as FLA33-

FLA36 with exception:

- no registers

- signals RST, RDY/BSY, Wait are not connected

Example P/N

7P004FLA5600C15

FLA63 No Attribute Memory, no Write

FLA59-FLA62 Based on 28F016S5; the same as FLA29-

Protect

FLA32 with exception:

- no registers

FLA64 With Attribute Memory, no Write

FLA65 No Attribute Memory, with Write Protect

FLA66 With Attribute Memory, with Write Protect

- signals RST, RDY/BSY, Wait are not connected

FLA59 No Attribute Memory, no Write

Protect

Example P/N

7P004FLA6600C15

ORDERING INFORMATION

7P XXX FLAYY SS T ZZ

XXX

002¹⁾

004

2MB

018¹⁾

4MB

024²⁾

8MB

032²⁾

12MB

040²⁾

16MB

18MB

020

20MB

28MB

36MB

006¹⁾

008

6MB

24MB

028²⁾

32MB

036²⁾

40MB

010¹⁾

012

014¹⁾

016

10MB

14MB

1)

2)

Available only for FLA21-FLA24, FLA25-FLA28, FLA51-FLA54, and FLA55-FLA59

Available only for FLA29-FLA32 and FLA59-FLA62

FLAYY

SS

Card Family and Version (See Card Family and Version Information)

00

01

02

WEDC Logo Silkscreen

Blank Housing, Type I

Blank Housing, Type I Recessed

T

C

=

Commercial

0°C to +70°C

I**

=

Industrial -40°C to +85°C

ZZ

15

150ns

Notes: Options without attribute memory and with hardware write protect switch are available.

** Denotes advanced information.

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

11

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

CIS INFORMATION FOR FLA SERIES CARDS

ADDRESS

VALUE

DESCRIPTION

ADDRESS

00H

VALUE

01H

DESCRIPTION

44H

49H

I

CISTPL_DEVICE

46H

37H

7

P

0

x

02H

03H

TPL_LINK

48H

50H

04H

53H

FLASH = 150ns (device writable)

4AH

30H

06H

0EH

16H

1EH

26H

2EH

36H

3EH

46H

4EH

5EH

6EH

7EH

8EH

9EH

CARD SIZE: 2MB

4MB

4CH

4EH

6MB

8MB

x

50H

46H

4CH

41H

F

L

A

10MB

12MB

14MB

16MB

18MB

20MB

24MB

28MB

32MB

36MB

40MB

52H

54H

56H

58H

32H

2

based on 28F008SA

with Att. Mem. no WP

32H

36H

2

6

based on 28F008S5

with Att. Mem. no WP

33H

30H

3

0

based on 28F016S5

with Att. Mem. no WP

5AH

5CH

5EH

60H

62H

64H

66H

68H

6AH

6CH

6EH

70H

72H

74H

76H

78H

7AH

66H

68H

6AH

6CH

6EH

70H

72H

74H

76H

78H

7AH

7CH

7EH

80H

82H

84H

2DH

31H

35H

20H

00H

43H

4FH

50H

59H

52H

49H

47H

48H

54H

20H

00H

43H

4FH

50H

59H

52H

49H

47H

48H

54H

20H

45H

4CH

45H

43H

54H

-

08H

0AH

0CH

0EH

10H

FFH

18H

02H

89H

END OF DEVICE

CISTPL_JEDEC_C

TPL_LINK

-

1

INTEL - ID

5

A2H

A6H

AAH

INTEL

28F008SA - ID

28F008S5 - ID

28F016S5 - ID

SPACE

END TEXT

C

12H

14H

16H

18H

1AH

1CH

1EH

20H

22H

24H

26H

28H

2AH

17H

03H

42H

01H

FFH

1EH

06H

02H

11H

01H

CISTPL_DEVICE_A

TPL_LINK

O

P

EEPROM - 200ns

Device Size = 2KBytes

END OF TUPLE

CISTPL_DEVICEGEO

TPL_LINK

Y

R

I

G

H

DGTPL_BUS

T

DGTPL_EBS

SPACE

DGTPL_RBS

END TEXT

DGTPL_WBS

C

DGTPL_PART

O

FLASH DEVICE

NON-INTERLEAVED

P

2CH

2EH

30H

32H

34H

36H

38H

3AH

3CH

3EH

40H

42H

20H

04H

F6H

01H

00H

15H

47H

05H

00H

45H

44H

CISTPL_MANFID

TPL_LINK(04H)

Y

R

EDI TPLMID_MANF: LSB

EDI TPLMID_MANF: MSB

LSB: Number Not Assigned

MSB: Number Not Assigned

CISTPL_VERS1

I

G

H

T

SPACE

TPL_LINK

E

L

TPLLV1_MAJOR

TPLLV1_MINOR

E

C

T

E

D

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

12

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

CIS INFORMATION FOR FLA SERIES CARDS (CONT.)

ADDRESS

86H

VALUE

52H

4FH

4EH

49H

43H

20H

44H

45H

53H

49H

47H

4EH

53H

20H

49H

4EH

43H

4FH

52H

50H

4FH

52H

41H

54H

45H

44H

20H

00H

31H

39H

37H

00H

FFH

1AH

05H

01H

00H

40H

03H

00H

FFH

00H

DESCRIPTION

R

88H

O

8AH

8CH

8EH

90H

N

I

C

SPACE

92H

D

94H

E

96H

S

98H

I

9AH

9CH

9EH

A0H

A2H

A4H

A6H

A8H

AAH

ACH

AEH

B0H

B2H

B4H

B6H

B8H

BAH

BCH

BEH

C0H

C2H

C4H

C6H

C8H

CAH

CCH

CEH

D0H

D2H

D4H

D6H

D8H

DAH

DCH

G

N

S

SPACE

I

N

C

O

R

P

O

R

A

T

E

D

SPACE

END TEXT

1

9

7

END TEXT

END OF LIST

CISTPL_CONF

TPL_LINK

TPCC_SZ

TPCC_LAST

TPCC_RADR

TPCC_RMSK

NULL CONTROL TUPLE

CISTPL_END

INVALID ADDRESS

The shaded area (addresses BEH C0H C2H C4H) can be different. It represents the

year of introducing the version of the card.

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

13

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com

PCMCIA Flash Memory Card

FLA Series

White Electronic Designs

Document Title

PCMCIA Flash Memory Card FLA Series

Revision History

Rev #

History

Release Date Status

Rev 0

Rev 6

Initial Release

April 2007

July 2007

Final

1.0 Update absolute maximum ratings commercial

temperature to 0°C to +60 °C from 30°C to +80 °C

White Electronic Designs Corp. reserves the right to change products or speciﬁcations without notice.

July 2007

Rev. 6

14

White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com


型号：	7R016FLA211I15
厂家：	Microsemi
描述：	Flash Card, 8MX16, 150ns, CARD-68
文件：	总14页 (文件大小：184K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

7R016FLA211I15 [MICROSEMI]

相关型号：

7R016FLA211I25

7R016FLA212C15

7R016FLA212C25

7R016FLA212I15

7R016FLA212I25

7R016FLA220C15

7R016FLA220C25

7R016FLA220I15

7R016FLA221I25

7R016FLA222C15

7R016FLA222I15

7R016FLA230C25