VCC1-E3E-12M352 [MICROSEMI]
CMOS Output Clock Oscillator, 12.352MHz Nom,;型号: | VCC1-E3E-12M352 |
厂家: | Microsemi |
描述: | CMOS Output Clock Oscillator, 12.352MHz Nom, |
文件: | 总10页 (文件大小:168K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
VCC1 series
1.8, 2.5, 3.3, 5.0 volt CMOS Oscillator
Features
· CMOS output
· Output frequencies to 190 MHz
rd
· Low jitter, Fundamental or 3 OT Crystal
· Tri-state output for board test and debug
· -10/70 or –40/85 °C operating temperature
· Gold over nickel contact pads
· Hermetically sealed ceramic SMD package
· Product is compliant to RoHS directive
and fully compatible with lead free assembly
The VCC1 Crystal Oscillator
Applications
· SONET/SDH/DWDM
· Ethernet, Gigabit Ethernet
· Storage Area Network
· Digital Video
· Broadband Access
· Microprocessors/DSP/FPGA
Description
Vectron’s VCC1 Crystal Oscillator (XO) is quartz
stabilized square wave generator with a CMOS
output, operating off a 1.8, 2.5, 3.3, or 5.0 volt
supply.
The VCC1 uses fundamental or 3rd overtone
crystals resulting in low jitter performance,
typically 0.5ps rms in the 12 kHz to 20MHz band.
Also a monolithic IC, which improves reliability
and reduces cost, is hermitically sealed.
fo
Output
Buffer /
Disable
Vectron International 267 Lowell Road, Hudson NH 03051
Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
Performance Characteristics
Table 1. Electrical Performance, 5V option
Parameter
Symbol
Min
0.012
4.5
Typical
Maximum
125.000
5.5
Units
MHz
V
V
mA
Frequency
fO
VDD
Operating Supply Voltage 1
Absolute Maximum Supply Voltage
Supply Current, Output Enabled
<1.5 MHz
5.0
-0.7
7.0
IDD
7
1.5 to 20 MHz
20.01 to 50 MHz
50.01 to 85 MHz
85.01 to 125 MHz
10
30
50
60
30
Supply Current, Out disabled
Output Logic Levels
IDD
uA
Output Logic High2
VOH
VOL
IOH
IOL
tR/tF
0.9*VDD
V
V
mA
mA
ns
Output Logic Low2
0.1*VDD
Output Logic High Drive
Output Logic Low Drive
Output Rise/Fall Time2
< 1.00 MHz
16
16
200
8
1.0 to 20.00 MHz
20.01 to 50.00 MHz
5
50.01 to 125.00 MHz
Duty Cycle3 (ordering option)
Operating Temperature (ordering option)
Storage Temperature
Stability4 (ordering option)
RMS Jitter, 12kHz to 20 MHz
Period Jitter, RMS
2
SYM
45/55
-10/70 or -40/85
%
°C
°C
ppm
ps
-55
125
±20, ±25, ±32, ±50, ±100
0.5
2.5
1
ps
V
Output Enable/Disable5
Output Enabled
4.0
Output Disabled
0.8
10
Internal Enable Pull-Up resistor5
Start-up time
100
Kohm
ms
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 1 defines these parameters. Figure 2 illustrates the operating conditions under which these parameters are tested and
specified.
3. Symmetry is measured defined as On Time/Period.
4. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under
operation).
5. Output will be enabled if enable/disable is left open.
tR
tF
IDD
VOH
50%
VOL
4
1
+
-
3
.1mF
.01mF
2
VDD
IC
V C
On Time
15pF
+
-
Period
Figure 1. Output Waveform
Figure 2. Typical Output Test Conditions (25±5°C)
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC1 Data sheet
Table 2. Electrical Performance, 3.3V option
Parameter
Symbol
Min
0.012
2.97
-0.5
Typical
Maximum
190.000
3.63
Units
MHz
V
V
mA
Frequency
fO
VDD
1
Operating Supply Voltage
Absolute Maximum Operating Voltage
Supply Current, Output Enabled
< 1.500 MHz
3.3
5.0
IDD
5
1.5 to 20 MHz
7
20.01 to 50 MHz
50.01 to 85 MHz
85.01 to 190 MHz
20
30
50
30
Supply Current, Output disabled
Output Logic Levels
IDD
uA
Output Logic High2
VOH
VOL
IOH
IOL
tR/tF
0.9*VDD
V
V
mA
mA
ns
Output Logic Low2
0.1*VDD
Output Logic High Drive
Output Logic Low Drive
Output Rise/Fall Time2
< 1.00 MHz
8
8
200
6
1.00 to 20.00 MHz
20.01 to 50.00 MHz
4
50.01 to 90.00 MHz
3
90.01 to 190.00 MHz
Duty Cycle3 (ordering option)
Operating Temperature (ordering option)
Storage Temperature
Stability4 (ordering option)
RMS Jitter, 12kHz to 20 MHz
RMS Jitter
2
SYM
45/55
-10/70 or –40/85
%
°C
°C
ppm
ps
-55
125
±20, ±25, ±32, ±50, ±100
0.5
2.5
1
ps
V
Output Enable/Disable5
Output Enabled
2.0
Output Disabled
0.5
10
Internal Enable Pull-Up resistor5
Start-up time
100
Kohm
ms
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 3 defines these parameters. Figure 4 illustrates the operating conditions under which these parameters are tested and
specified. For Fo>90MHz, rise and fall time is measured 20 to 80%.
3. Symmetry is measured defined as On Time/Period.
4. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under
operation).
5. Output will be enabled if enable/disable is left open.
tR
tF
IDD
VOH
50%
VOL
4
1
+
-
3
.1mF
.01mF
2
VDD
IC
V C
On Time
15pF
+
-
Period
Figure 3. Output Waveform
Figure 4. Typical Output Test Conditions (25±5°C)
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC1 Data sheet
Table 3. Electrical Performance, 2.5V option
Parameter
Symbol
Min
0.012
2.25
-0.5
Typical
Maximum
190.000
2.75
Units
MHz
V
V
mA
Frequency
fO
VDD
1
Operating Supply Voltage
Absolute Maximum Voltage
Supply Current, Output Enabled
< 20 MHz
2.5
5.0
IDD
7.0
15.0
20.0
30.0
30
20.01 to 50 MHz
50.01 to 110 MHz
110.1 to 190 MHz
Supply Current, Out disabled
Output Logic Levels
IDD
uA
Output Logic High2
VOH
VOL
IOH
IOL
IOH
IOL
tR/tF
0.9*VDD
V
V
Output Logic Low2
0.1*VDD
Output Logic High Drive
Output Logic Low Drive
Output Logic High Drive3
Output Logic Low Drive3
Output Rise/Fall Time2
<1.00 MHz
4
4
8
8
mA
mA
mA
mA
ns
200
10
6
1.00 to 20.00 MHz
20.01 to 50.00 MHz
50.01 to 90.00 MHz
3
90.01 to 190.00 MHz
Duty Cycle4 (ordering option)
Operating Temperature (ordering option)
Storage Temperature
Stability5 (ordering option)
RMS Jitter, 12kHz to 20 MHz
RMS Jitter
2
SYM
45/55
-10/70 or –40/85
%
°C
°C
ppm
ps
-55
125
±20, ±25, ±32, ±50, ±100
0.5
2.5
1
ps
V
Output Enable/Disable6
Output Enabled
1.75
Output Disabled
0.5
10
Internal Enable Pull-Up resistor6
Start-up time
100
Kohm
ms
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 5 defines these parameters. Figure 6 illustrates the operating conditions under which these parameters are tested and
specified.
3. Overtone designs, output frequencies>35MHz.
4. Symmetry is measured defined as On Time/Period.
5. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under
operation).
6. Output will be enabled if enable/disable is left open.
tF
tR
IDD
4
1
%
80
+
-
3
.1mF
.01mF
2
VDD
Vs
IC
VC
15pF
20%
+
-
On Time
Period
Figure 5. Output Waveform
Figure 6. Typical Output Test Conditions (25±5°C)
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC1 Data sheet
Table 4. Electrical Performance, 1.8V option
Parameter
Symbol
Min
0.048
1.71
-0.5
Typical
Maximum
172.000
1.89
Units
MHz
V
V
mA
Frequency
fO
VDD
1
Operating Supply Voltage
Absolute Maximum Voltage
Supply Current, Output Enabled
< 20 MHz
1.8
3.6
IDD
5
20.01 to 70 MHz
70.01 to 96 MHz
96.01 to 125 MHz
125.01 to 172 MHz
15
20
25
30
30
Supply Current, Out disabled
Output Logic Levels
Output Logic High2
IDD
uA
VOH
VOL
IOH
IOL
IOH
IOL
tR/tF
0.9*VDD
V
V
Output Logic Low2
0.1*VDD
Output Logic High Drive
Output Logic Low Drive
Output Logic High Drive3
Output Logic Low Drive3
Output Rise/Fall Time2
< 1.00 MHz
2.8
2.8
8
mA
mA
mA
mA
ns
8
200
4
1.000 to 20.00 MHz
20.01 to 50.00 MHz
4
50.01 to 90.00 MHz
3
90.01 to 172.00 MHz
Duty Cycle4 (ordering option)
Operating temperature (ordering option)
Storage Temperature
Stability5 (ordering option)
RMS Jitter, 12kHz to 20 MHz
RMS Jitter
2
SYM
45/55
-10/70 or –40/85
%
°C
°C
ppm
ps
-55
125
±20, ±25, ±32, ±50, ±100
0.5
2.2
ps
V
Output Enable/Disable6
Output Enabled
1.26
Output Disabled
0.5
10
Internal Enable Pull-Up resistor6
Start-up time
1
Mohm
ms
1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.
2. Figure 7 defines these parameters. Figure 8 illustrates the operating conditions under which parameters are tested/specified.
3. Overtone designs, output frequencies>35MHz.
4. Symmetry is measured defined as On Time/Period.
5. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under
operation).
6. Output will be enabled if enable/disable is left open.
tF
tR
IDD
%
80
4
1
Vs
+
-
3
.1mF
.01mF
2
VDD
20%
IC
VC
15pF
+
-
On Time
Period
Figure 7. Output Waveform
Figure 8. Typical Output Test Conditions (25±5°C)
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC1 Data sheet
Enable/Disable Functional Description
Under normal operation the Enable/Disable is left open or set to a logic high state. When the E/D is set to a
logic low, the oscillator stops and the output is in a high impedance state. This helps reduce power
consumption as well as facilitating board testing and troubleshooting.
Tri-state Functional Description
Under normal operation the tri-state is left open or set to a logic high state. When the tri-state is set to a
logic low, the oscillator remains active but the output buffer is in a high impedance state. This helps facilitate
board testing and troubleshooting.
Table 5. Outline Diagrams, Pad Layout and Pin Out
Pin #
Symbol
E/D or NC
GND
Function
Tri-state, Enable/Disable or NC
Electrical and Case Ground
Output Frequency
1
2
3
4
fO
VDD
Supply Voltage
Contact Pads are gold over nickel
Figure 9, Package drawing
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC1 Data sheet
Contact Pads are gold over nickel
Figure 10, Alternate Package drawing
Tape and Reel
Table 6: Tape and Reel Dimensions (mm)
J
F
G
D
C
B
A
I
L
E
H
K
Tape Dimensions
Reel Dimensions
# Per
Product
A
B
C
D
E
F
G
H
I
J
K
L
Reel
16
7.5
1.5
4
8
2
21
13
60
2
17
180
VCC1
1000
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC1 Data sheet
Reliability
The VCC1 qualification tests have included:
Table 7. Environnemental Compliance
Parameter
Conditions
MIL-STD-883 Method 2022
MIL-STD-883 Method 2007
MIL-STD-883 Method 1010
MIL-STD-883 Method 2003
MIL-STD-883 Method 1014
MIL-STD-883 Method 2015
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Gross and Fine Leak
Resistance to Solvents
Handling Precautions
Although ESD protection circuitry has been designed into the the VCC1, proper precautions should be taken
when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for
ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit
parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a
standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be
used for comparison purposes.
Table 8. ESD Ratings
Model
Human Body Model
Charged Device Model
Minimum
1000
Conditions
MIL-STD-883 Method 3115
JESD 22-C101
1500
Suggested IR profile
Devices are built using lead free epoxy and can also be subjected to standard lead free IR reflow conditions,
Table 9 shows max temperatures and lower temperatures can also be used e.g. peak temperature of 220C.
Table 9. Reflow Profile (IPC/JEDEC J-STD-020B)
Parameter
Symbol
Value
Preheat Time
t S
150 sec Min, 200 sec Max
Ramp Up
RUP
t L
3 oC/sec Max
60 sec Min, 150 sec Max
480 sec Max
Time Above 217 oC
Time To Peak Temperature
Time At 260 oC (max)
Time At 240 °C (max)
Ramp Down
t AMB-P
t P
10 sec Max
tp2
60 sec Max
6 oC/sec Max
RDN
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC1 Data sheet
Table 10. Standard Frequencies (MHz)
1.544
4.9152
9.830
1.843
5.000
2.000
6.000
2.048
6.176
2.560
7.3728
12.000
12.81089
13.560
14.400
15.555
16.388
16.896
17.920
19.200
19.752
20.516
20.875
21.711
22.855
24.5454
26.000
28.60489
29.500
31.500
32.768
33.8688
35.840
37.140
39.0625
40.920
42.000
44.267
45.818
47.404
49.36221
51.840
54.2174
57.272
60.000
63.8976
66.667
70.656
76.800
83.300
91.008
106.250
128.000
189.000
3.080
7.680
3.686
8.000
4.000
8.192
4.032
9.216
4.096
9.600
10.000
12.624
13.400
14.318
15.000
16.128
16.670
17.664
18.750
19.654
20.200
20.829
21.504
22.579
24.444
25.180
27.500
29.265
31.104
32.270
33.792
35.46895
36.923
38.810
40.550
41.750
44.137
45.000
47.13333
48.81441
51.156
54.000
56.446
58.982
62.500
66.600
69.632
74.176
81.000
89.512
102.400
125.000
157.000
10.240
12.729
13.401
14.31818
15.211
16.368
16.776
17.734
19.000
19.660
20.2752
20.829
21.616
22.5792
24.540
25.272
28.000
29.491
31.250
32.500
33.810
35.500
37.000
38.880
40.632
41.895
44.236
45.135
47.16602
49.127
51.200
54.072
56.448
58.982
62.800
66.660
70.000
74.250
81.920
89.97804
103.680
125.010
166.000
10.486
12.800
13.500
14.336
15.360
16.384
16.780
17.73448
19.022
19.6608
20.480
20.830
21.71055
22.600
24.545
25.920
28.224
29.49893
31.307
32.764
33.860
35.600
37.056
38.912
40.63232
41.931
44.250
45.158
47.197
49.152
51.840
54.125
56.666
59.000
63.000
66.666
70.626
75.000
83.000
90.000
104.000
127.000
167.000
12.222
12.960
13.711
14.500
15.625
16.500
16.9344
17.992
19.268
19.774
20.712
20.950
22.000
22.85568
24.576
26.25641
28.636
30.000
31.680
32.768
34.368
35.984
37.376
39.497
40.960
42.400
44.330
46.080
47.40437
49.408
52.000
54.500
57.344
60.480
64.000
66.670
70.660
77.680
83.333
92.000
110.000
133.000
190.000
12.2725
13.000
13.824
14.5152
15.748
16.588
17.000
18.000
19.286
19.872
20.736
20.971
22.118
23.000
24.704
26.664
28.63636
30.150
31.948
32.800
34.450
36.000
37.500
39.9278
41.472
42.500
44.434
46.232
48.000
49.512
52.416
55.000
57.600
61.000
64.512
67.500
70.676
77.760
85.000
95.000
112.500
135.000
12.288
13.070
14.000
14.720
15.74886
16.610
17.0664
18.333
19.392
19.968
20.769
21.000
22.174
23.040
24.832
26.6649
28.65645
30.200
31.949
33.000
34.560
36.500
37.643
40.000
41.500
42.620
44.539
46.2321
48.33008
49.58632
52.500
55.289
57.800
61.250
65.000
67.584
70.833
78.000
87.040
96.000
114.000
144.600
12.352
13.107
14.284
14.736
15.974
16.660
17.37476
18.400
19.440
20.000
20.7692
21.333
22.184
23.732
25.000
26.666
28.672
30.720
32.000
33.1776
34.816
36.666
38.000
40.010
41.657
43.000
44.732
46.320
48.587
49.867
52.560
55.500
58.000
61.440
65.520
68.000
71.680
78.336
87.182
97.776
115.200
150.000
12.500
13.200
14.2848
14.745
16.000
16.666
17.408
18.432
19.456
20.00271
20.800
21.400
22.217
24.000
25.088
27.000
28.800
30.880
32.250
33.300
35.000
36.860
38.3107
40.079
41.660
43.560
44.736
46.796
48.58736
49.980
53.125
56.000
58.250
62.000
65.536
68.680
72.000
79.452
87.472
98.304
116.640
155.520
12.544
13.248
14.285
14.746
16.016
16.667
17.600
18.688
19.530
20.141
20.828
21.500
22.500
24.431
25.175
27.120
29.000
31.000
32.256
33.333
35.280
36.864
38.800
40.500
41.670
44.000
44.928
46.864
48.600
50.000
53.330
56.064
58.320
62.208
66.000
68.736
73.728
80.000
89.472
100.000
120.000
156.250
Other frequencies may be available upon request. Standard frequencies are frequencies which the crystal
has been designed and does not imply a stock position.
Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1
e-mail: vectron@vectron.com
VCC1 Data Sheet
Ordering Information
VCC1 - B
3
B - 125M00
Product Family
Output Frequency
Crystal Oscillator
In MHZ
Stability Options
Voltage Options
Electrical Options
A: ±100ppm, -10 to 70°C
C: ±100ppm, -40 to 85°C
B: ±50ppm, -10 to 70°C
D: ±50ppm, -40 to 85°C
K: ±32ppm, -10 to 70°C
O: ±32ppm, -40 to 85°C
E: ±25ppm, -10 to 70°C
F: ±25ppm, -40 to 85°C
VCC1-103= ±20ppm, -10 to 70C
A: +5.0 Vdc +/-10%, 15pF
B: +3.3 Vdc +/-10%, 15pF
C: +3.0 Vdc +/-10%, 15pF
E: +5.0 Vdc +/-10%, 50pF
F: +3.3Vdc +/-10%, 50pF
G: +2.5Vdc +/-10%, 15pF
H: +1.8Vdc +/-10%, 15pF
3: Tri-state, 45/55% Duty
The following codes are not
recommended for new designs
0: No tri-state, 40/60% Duty
1: Tri-state, 40/60% Duty
2: No tri-state, 45/55%Duty
5: Enable, 40/60% Duty
6: Enable, 45/55% Duty
Note: Not all combinations are available.
Tri-state with a 45/55% is the most common Electrical code and is recommended for most applications.
For Additional Information, Please Contact:
USA: Vectron International · 267 Lowell Road, Hudson, NH 03051
· Tel: 1-88-VECTRON-1 · Fax: 1-888-FAX-VECTRON
EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany ·
Tel: 49 (0) 7268 8010 · Fax: 49 (0) 7268 801281
ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd.,
WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131
•Tel: 8621 50480777 • Fax: 8621 50481881
www.vectron.com
January 26, 2006
Vectron International 267 Lowell Rd, Hudson NH 03051
Tel: 1-88-VECTRON-1
10
e-mail vectron@vectron.com
相关型号:
©2020 ICPDF网 联系我们和版权申明