MF-27WXC-M01ZAC49 [MITSUBISHI]
Optoelectronic Device;型号: | MF-27WXC-M01ZAC49 |
厂家: | Mitsubishi Group |
描述: | Optoelectronic Device 光电 |
文件: | 总15页 (文件大小:230K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MITSUBISHI (OPTICAL DEVICES)
Mitsubishi Electric Corp.
Datasheet
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
2.7Gbps Multi-Rate CWDM SFP Transceiver with Digital Diagnostic
Monitoring Interface MF-27WXC Series
1. Description
This transceiver is compliant with Small
Form-factor Pluggable (SFP) MSA, and
optimized for 155Mbps to 2.7Gbps Coarse
Wavelength Division Multiplexing (CWDM)
applications.
The optical subassembly consists of 2 parts,
the transmitter with an uncooled DFB laser in
a hermetic coaxial module, the receiver with
an PD preamp in a hermetic coaxial module
and integrated circuits for reshaping received
optical signal.
The built-in serial ID recognition is
incorporated, which allows users to interface
with two wire serial interface that displays
information on manufacturer, part number,
link, distance, and other parameters.
The Digital Diagnostic Monitoring interface is
incorporated, which monitors transceiver
parameters including Temperature, Supply
voltage, Laser bias current, Laser power and
Received optical power.
2. Features
•
•
•
•
•
•
•
•
•
•
Small Form-factor Pluggable (SFP) MSA compliant transceiver with SONET/SDH system Quality
Full 8 wavelength line-up for CWDM grid
155Mbps to 2.7Gbps Multi-Rate operation capability
LC duplex receptacle
Single +3.3V power supply
Differential data inputs and outputs
Operating case temperature range 0°C to +70°C
Comply with SFF-8472 MSA
Built-in Programmable receiver low pass filter as application select
Incorporating Digital Diagnostic Monitoring Interface with External calibration
(Internal calibration is optional)
•
•
•
Serial ID Functionality
Slide latch / Bail latch type
RoHS Compliant
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 1 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
3. Block diagram
Rx Received Po
Monitor Circuit
Signal Detect
Circuit
RX_LOS
PD
RD-
OPT_IN
Limiting Amp
&Low pass Fil.
RD+
TIA
ROSA
Temperature
Monitor Circuit
Control
Circuits
(DDM)
Supply Voltage
Monitor Circuit
MOD DEF 2
MOD DEF 1
LD Bias & Pout
Monitor Circuit
Memory
TX_Fault
TD-
Fault Detector
Driver
LD
TD+
OPT_OUT
L
Bias
TX_Disable
Monitor
PD
circuit
TOSA
4. Absolute Maximum Ratings
Stress below listed absolute maximum rating may cause permanent damage to the module.
This is a stress only and functional operation of the module at these or any other conditions in excess of
those given in the operational sections of this data sheet.
Exposure to Absolute Maximum Rating for extended periods may affect module reliability.
Parameters
Symbol
Vcc
Tstg
Tc
Ratings
0 to +4.0
-40 to +85
0 to +70
5 to 85
Unit
V
Supply voltage
C
Storage temperature
Operating case temperature
Relative humidity (non condensation)
°
C
°
-
%
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 2 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
5. Electrical characteristics
All parameters are specified over the operating case temperature.
Measurement conditions are at 2.48832Gbps +/-20ppm, NRZ PN223-1 and 50%duty cycle data signal.
The DATA input/output signal interface is AC-coupled internally.
TX_DISABLE input signal level is LVTTL compatible. (With internally pull-up 4.7k to 10kΩ)
TX_FAULT and LOS(Loss Of Signal) output are Open-Collector/drain, and the levels indicated assuming 4.7k
to 10k ohm pull up resistor to Host_Vcc is present.
Parameters
Supply voltage
Power consumption
Symbol
Vcc
Pc
VIH
VIL
Min.
3.13
-
2.0
Typ.
3.3
0.8
-
Max.
3.47
1.2
Vcc
0.8
Unit
V
W
V
TX_DISABLE Input voltage
0
-
V
VOH
VOL
VOH
VOL
VOH
VOL
VIH
VIL
VT
RT
VO
RO
2.0
0
2.0
0
-
-
-
-
-
-
-
-
-
Vcc
0.5
Vcc
0.5
Vcc
0.4
V
V
V
V
V
V
V
V
mVP-P
Ω
mVP-P
Ω
TX_FAULT Output voltage
RX_LOS Output voltage
Vcc × 0.8
MOD_DEF[2] Output voltage
MOD_DEF[1], [2] Input voltage
0
Vcc
Vcc × 0.3
2400
-
Vcc × 0.7
0
500
-
370
-
Input Amplitude, Differential
Input Impedance, Differential
Output Amplitude, Differential
Output Impedance, Differential
Data Output Rise/Fall Time
(20% to 80%)
Electrical Input Data Return Loss
100MHz < f < 1.2GHz(Differential)
Electrical Input Data Return Loss
1.2GHz < f < 2.7GHz(Differential)
100
-
100
1600
-
Tr/Tf
Rld1
Rld2
-
12
8
-
-
-
150
ps
dB
dB
-
-
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 3 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
6. Optical characteristics
Transmitter
Parameter
Target Distance
Wavelength
Min.
-
Max.
50
Unit
Km
nm
-
note 1
SLM
Optical source
Optical power BOL (3.3V, 25degC)
Optical power EOL
Optical power when disable
Spectral width(-20dB)
SMSR
+1
0
-
-
30
8.2
+5
+5
-40
1.0
-
dBm
dBm
dBm
nm
dB
Extinction ratio
12
dB
Optical waveform
SONET/SDH Mask compliant
-
Return Loss at S
24
-
-
1
dB
dB
Path penalty (note 2)
Jitter Generation(note 3)
-Bandwidth 5KHz to 20MHz
(ITU-T G.958,G.813 compliant)
Jitter Generation(note 3)
-Bandwidth 1MHz to 20MHz
(ITU-T G.958,G.813 compliant)
-
-
0.5
0.1
UIpp
UIpp
note 1 : The wavelength range is –5.5 to +7.5 nm from each center wavelength.
Min.
Typ.
1610
1590
1570
1550
1530
1510
1490
1470
Max.
Unit
nm
1604.5
1584.5
1564.5
1544.5
1524.5
1504.5
1484.5
1464.5
1617.5
1597.5
1577.5
1557.5
1537.5
1517.5
1497.5
1477.5
note 2 : Support 50km of normal single-mode fiber.
Chromatic Dispersion is required by each wavelength.
Wavelength
1610nm
1590nm
1570nm
1550nm
1530nm
1510nm
1490nm
1470nm
Chromatic Dispersion
Unit
1000
900
900
900
800
800
700
700
ps/nm
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 4 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
note 3 : Jitter Generation
Optical Input Power
=Overload BOL
RxD+
Jitter Analyzer
SFP Rx
Opt.
ATT
RxD-
TxD-
SFP Tx
Opt.
ATT
TxD+
Receiver
Wavelength
Parameter
Min.
1270
Max.
1620
Unit
nm
Sensitivity BOL
-
-19
dBm
(3.3V, 25degC, BER=1E-10)
Sensitivity EOL (BER=1E-10)
Overload BOL (3.3V, 25degC)
Overload
RX_LOS Assert Level
RX_LOS De-assert Level
RX_LOS Hysteresis
-
+1
0
-30
-
-18
-
-
dBm
dBm
dBm
dBm
dBm
dB
-
-20
6.0
1.0
0.3
-
CID Penalty(note 1)
dB
Jitter Tolerance, Transfer
Maximum reflectance of receiver at R
ITU-T G.958 Compliant(with reference CDR)
-27
-
dB
-
note 1 : Penalty between PRBS 2E23-1 and Consecutive Identical Digits according to ITU-T G957
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 5 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
7. Digital Diagnostic Monitoring Accuracy
The diagnostic monitoring features internal calibration, and is calibrated over operating temperature and
voltage range. The monitor parameters are represented as defined in SFF-8472.
These parameters of the monitoring accuracy are guaranteed, as long as operating conditions of this SFP
transceiver do not exceed ranges defined below.
Digital Diagnostic Monitoring Accuracy
Parameter
Transceiver Temperature*1
Supply Voltage
TX Bias Current
TX Optical Power
RX Optical Power
Min.
-3
-3
Max.
+3
+3
Unit
°C
%
%
dB
dB
Range for Accurate Monitoring
0 to 70°C
3 to 3.6 V
-
0 to 5 dBm
-19 to 0 dBm
-10
+10
-3(-1.5*2) +3(+1.5*2)
-3(-2*2)
+3(+2*2)
*1:Transceiver Temperature is defined as a case temperature.
*2:These spec are optional.
8. Selective Bandwidth filtering function
Receiver bandwidth is selected by the Rate Select pins(7pin and 9pin).
Each bit rates for the selective bandwidth and adaptable protocols are as follows.
No. Rate Select 0 (7pin) Rate Select 1 (9pin)
Bandwidth
Full
1.25Gbps
622Mbps
155Mbps
Adaptable protocols
STM-16/OC-48, OTN-1
Gigabit Ethernet
STM-4/OC-12, ESCON
STM-1/OC-3, FDDI
1
2
3
4
Low
High
Low
High
Low
Low
High
High
*Optional Bandwidth : 2.125Gbps and 1.062Gbps bandwidth can be selected by the internal setting.
9. Transceiver pin allocation
No.
1
Symbol
TX GND
TX_FAULT
Description
No.
Symbol
Description
Receiver Ground
Transmitter Ground
11 RX GND
12 RD-
2
Transmitter Fault Indication
Receiver Data Output-Bar
Receiver Data Output
Receiver Ground
3
TX_DISABLE Transmitter Disable
13 RD+
4
MOD_DEF[2]
MOD_DEF[1]
MOD_DEF[0]
Rate Select 0
RX_LOS
Module Definition 2
Module Definition 1
Module Definition 0
Rate Select pin 0
Loss of Signal
14 RX GND
15 RX Vcc
16 TX Vcc
17 TX GND
18 TD+
5
Receiver Power Supply
Transmitter Power Supply
Transmitter Ground
6
7
8
Transmitter Data in
9
Rate Select 1
Rate Select pin 1
Receiver Ground
19 TD-
Transmitter Data in-Bar
Transmitter Ground
10 RX GND
20 TX GND
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 6 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
10. Pin Descriptions
Pin No.
Function
I/O
Pin description
1,17,20 TX GND
I
These pins are the Transmitter ground connections.
They should be connected to a low impedance ground plane(0V).
9,10,
11,14
16
RX GND
TX Vcc *
I
I
These pins are the Receiver ground connections.
They should be connected to a low impedance ground plane(0V).
This is the power supply pin for the Transceiver part.
It should be connected to +3.3V.
Recommended power supply decoupling. (See Figure 8)
15
RX Vcc *
TD+ / TD-
I
I
This is the power supply pin for the Receiver part.
It should be connected to +3.3V.
Recommended power supply decoupling. (See Figure 8)
* Both TX Vcc and RX Vcc have been internally connected due to supply of
control circuit Vcc.
This data input pin modulates the laser diode. When the TD+ input is asserted, the
laser diode is turned on.
18,19
They are internally AC-coupled into an equivalent load of RI differential, as shown
in Figure 8.
3
TX_DISAB
LE
I
Active high TTL input, with internal 7.4k ohm pull-up resistor to Vcc.
Asserting the transmitter disable will deactivate the laser within the assert time.
Table 1 indicates the timing of TX_DISABLE.
12,13
RD+ / RD-
O
Received Data Out and Inverted Received Data Out are differential serial output
from the receiver.
These are AC-coupled 100 ohm differential lines which should be terminated with
a 100 ohm (differential) at the user SERDES, as shown in Figure 8. AC coupling is
done inside the module and is thus not required on the host board.
Active high open collector/drain output which indicates a loss-of-signal condition
(LOS). When the average optical power received by the module is below the
Assert Level, RX_LOS is indicated.
Table 1 indicates the timing of RX_LOS. RX_LOS requires a 4.7k to 10k ohm
pull-up resistor external to the module, i.e., in the host system Host_Vcc, as shown
in Figure 8.
The pull-up voltage is between 2.0 V and VccR(VccT) + 0.3 V.
Active high open collector/drain output which indicates a fault in the module. This
can be failure of the laser diode. Under this conditions, TX_FAULT will activate
and be latched. And then the laser will be deactivated within the assert time.
TX_FAULT also requires a 4.7k to 10k ohm pull-up resistor externally, i.e. in the
host system Host_Vcc, as shown in Figure 8.
8
2
RX_LOS
O
O
TX_FAULT
The pull-up voltage is between 2.0 V and VccT(VccR) +0.3V.
It can be reset by toggling TX_DISABLE high for at least t_reset.
See Figure 8 and Figure 5.
6,5,4
MOD_DEF
[0:2]
-
I
This module has a serial ID function which provides information about the
transceiver’s capabilities, standard interfaces, manufacturer and other information.
This function is provided via a two wire serial EEPROM interface.
MOD_DEF[0] is connected to ground inside the module.(LOW)
MOD_DEF[1] is the serial clock signal input.(SCL)
MOD_DEF[2] is the data output/input.(SDA)
The serial ID definitions are as given in the “SFP-MSA” standard.
See Figure 9.
These pins defined the bandwidth filters. 7pin/9pin setting=[*/*]:
[0/0]:Full bandwidth, [1/0]:1.25Gbps, [0/1]:622Mbps, [1/1]:155Mbps
These input pins are internally pulled down to GND with 33Kohm resistor.
If this function is not used, both pins should be left open or connected to GND.
7,9
Rate Select
0, 1
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 7 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
Table 1
Timing of control and status I/O
The timing of the control and status line are listed in below and Figure 1 to 7.
Parameter
TX_DISABLE
Assert Time
Symbol
Min
Max
Unit
Condition
Time from rising edge of TX_DISABLE to
when the optical output falls below 10% of
nominal
t_off
-
10
µs
TX_DISABLE
Negate Time
Time from falling edge of TX_DISABLE to
when the modulated optical output rises
above 90% of nominal
From power on or negation of TX_FAULT
using TX_DISABLE
t_on
-
-
1
ms
ms
Time to Initialize,
Including Reset of
TX_FAULT
TX_FAULT
Assert Time
TX_DISABLE
to Reset
RX_LOS
Assert Time
RX_LOS
Negate Time
Serial ID
t_init
300
Time from fault to TX_FAULT on
T_fault
T_reset
t_losson
t_lossoff
f_clock
-
10
-
100
-
µs
µs
Time TX_DISABLE must be held high to
reset TX_FAULT
Time from LOS state to RX_LOS Assert
100
100
100
µs
Time from non-LOS state to RX_LOS
de-assert
-
µs
-
kHz
-
Clock Rate
Figure 1
Power on initialization of SFP transceiver, TX_DISABLE negated
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 8 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
Figure 2
Power on initialization of SFP transceiver, TX_DISABLE asserted
Figure 3
SFP TX_DISABLE timing during normal operation
Figure 4
Detection of transmitter fault condition
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 9 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
Figure 5
Successful recovery from transient fault condition
Figure 6
Unsuccessful recovery from fault condition
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 10 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
Figure 7
Timing of RX_LOS detection
Figure 8
Example of SFP Host Board Schematic
SFP Module
Host Board
Protocol Vcc
TD+
LASER
100 ohm
DRIVER
TD-
4.7k to 10k
ohm
TX_FAULT
TX_DISABLE
TX GND
7.4k ohm
1 uH
TX Vcc
RX Vcc
0.1 uF
10 uF
1 uH
+3.3V
PROTOCOL
IC
0.1 uF 10 uF
SERDES
IC
0.1 uF 10 uF
RX GND
RD+
PREAMP
&
POSTAMP
100 ohm
RD-
RX_LOS
Rate Select 0
Rate Select 1
4.7k to 10k
ohm
+3.3V
33k ohm
33k ohm
4.7k to 10k
ohm
4.7k to 10k
ohm
MOD_DEF[0]
MOD_DEF[1]
MOD_DEF[2]
PLD/PAL
SERIAL ID
4.7k to 10k
ohm
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 11 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
Figure 9 Serial ID Table
Data
Data
[HEX]
03
Data
Address
64
Data
[HEX]
00
Name of Field
ASCII
Name of Field
ASCII
Address
0
Identifier
Ext. Identifier
Connector
Options
1
04
07
00
0A
00
00
00
00
00
00
03
19
00
32
FF
00
00
00
00
4D
49
54
53
55
42
49
53
48
49
20
45
4C
45
43
20
00
08
00
70
4D
46
2D
32
37
57
58
43
4D
33
31
5A
41
43
note 1
note 1
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
Options
1A
2
BR, max
00
3
Transceiver
Transceiver
Transceiver
Transceiver
Transceiver
Transceiver
Transceiver
Transceiver
Encoding
BR, min
00
4
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Vendor SN
Date code
Date code
Date code
Date code
Date code
Date code
Date code
Date code
note 4
note 4
note 4
note 4
note 4
note 4
note 4
note 4
note 4
note 4
note 4
note 4
note 4
note 4
note 4
note 4
note 5
note 5
note 5
note 5
note 5
note 5
note 5
note 5
58
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
BR, Nominal
Reserved
Length(9um)-km
Length(9um)
Length(50um)
Length(62.5um)
Length(Copper)
Reserved
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Vendor name
Reserved
M
I
T
S
U
B
I
S
H
92 Diagnostic Monitoring Type
93 Enhanced Options
94 SFF-8472 Compliance
I
00
SPACE
01
E
95
96
CC_EXT
note 3
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
note 6
L
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
Vendor Specific
E
C
97
98
SPACE
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Vendor OUI
Vendor OUI
Vendor OUI
Vendor PN
M
F
-
Vendor PN
Vendor PN
Vendor PN
2
Vendor PN
7
Vendor PN
W
X
C
M
3
Vendor PN
Vendor PN
Vendor PN
Vendor PN
Vendor PN
1
Vendor PN
Z
A
C
*
Vendor PN
Vendor PN
Vendor PN
Vendor PN
*
Vendor rev
Vendor rev
Vendor rev
Vendor rev
Wavelength (*)
Wavelength (*)
Reserved
note 2
note 2
00
CC_BASE
note 3
note 1 : These PN ASCII codes depend on wavelength..
note 3 : This code is check sum code.
Data Address(54/55): 1470nm;4/7, 1490nm;4/9, 1510nm;5/1, 1530nm;5/3,
1550nm;5/5, 1570nm;5/7, 1590nm;5/9, 1610nm;6/1
note 4 : These address shows unique device serial number.
note 5 : These address shows date code.
note 2 : These codes depend on wavelength.
note 6 : These address are vendor specific area. Read only.
Data Address(60/61): 1470nm;05/BE, 1490nm;05/D2, 1510nm;05/E6, 1530nm;05/FA,
1550nm; 06/0E, 1570nm;06/22, 1590nm;06/36, 1610nm;06/4A
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 12 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
11. Type Number
MF – 27WXC – M 3 1 Z A C 47
Center Wavelength
C47 : 1470nm
C49 : 1490nm
C51 : 1510nm
C53 : 1530nm
C55 : 1550nm
C57 : 1570nm
C59 : 1590nm
C61 : 1610nm
Operational Temperature Range
A : 0 ~ +70°C
M2 : Slide latch type & External Calibration
M3 : Bail latch type & External Calibration
(M0 : Slide latch type & Internal Calibration)
(M1 : Bail latch type & Internal Calibration)
12. Reliability reference
Telcordia GR-468-CORE
Radiated Emission:IEC61000-6-3
Immunity:IEC61000-4-2,IEC61000-4-3
Flammability:UL94V-0
ESD for PIN Interface:500V by Human body model (with Rd=1500ohm and Cd=100pF)
13. Laser Safety Information
Class 1 Laser Product(IEC60825 and CDRH compliant)
14. Data sheet
Data sheet which is attached the SFP includes the below parameters.
Condition:
T-ambient 25deg.
Nominal Voltage
Data rate 2.48832Gbps
Data pattern PRBS2E23-1
Parameters:
・ Optical Output Power
・ Wavelength
・ Spectral Width
・ Supply Current
・ Receiver Sensitivity
・ Receiver Overload
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 13 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
15. General Outline Drawing
Slide latch type
MF-27WXC-M21ZAC47
27WXC-M21C47
[ unit : mm]
Bail latch type
MF-27WXC-M31ZAC47
27WXC-M31C47
[unit: mm]
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 14 of 15
MITSUBISHI (OPTICAL DEVICES)
MF-27WXC Series
2.5Gbps SFP TRANSCEIVER MODULE
16. Packing
Ten SFPs are packed up in this packing box.
Presses Plate
SFP
Dust Cap
Packing box
- Capacity : 10pcs. / box
- Packing box and Presses Plate material :
Cardboard with ESD protection coat.
This product is sensitive to electrostatic discharge. Take precautions to prevent ESD; use wrist straps,
grounded work surfaces and recognized anti-static techniques when handling SFP module.
Mitsubishi reserves the right to change the circuitry and specifications without notice at any time.
No liability is assumed as a result of their use or application. No rights under any patent accompany
the sale of any such product(s) or information.
The end of document
UQ9-06-001 Ed:1.0 Date:10.Feb.2006
Page 15 of 15
相关型号:
©2020 ICPDF网 联系我们和版权申明