PM75RSD060 [MITSUBISHI]
FLAT-BASE TYPE INSULATED PACKAGE; FLAT -BASE型绝缘包装
| 型号： | PM75RSD060 |
| 厂家： | 
Mitsubishi Group |
| 描述： | FLAT-BASE TYPE INSULATED PACKAGE |
| 文件： | 总9页 (文件大小：147K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MITSUBISHI<INTELLIGENTPOWER MODULES>
PM75RSD060
FLAT-BASETYPE
INSULATEDPACKAGE
PM75RSD060
FEATURE
a) Adopting new 4th generation planar IGBT chip, which per-
formance is improved by 1µm fine rule process.
For example, typical VCE(sat)=1.7V
b) Using new Diode which is designed to get soft reverse
recovery characteristics.
c) Keeping the package compatibility.
The layout/position of both terminal pin and mounting hole
is same as S-series 3rd generation IPM.
• 3φ 75A, 600V Current-sense IGBT for 15kHz switching
• 30A, 600V Current-sense regenerative brake IGBT
• Monolithic gate drive & protection logic
• Detection, protection & status indication circuits for over-
current, short-circuit, over-temperature & under-voltage
(P-Fo available from upper leg devices)
• Acoustic noise-less 5.5/7.5kW class inverter application
• UL Recognized
Yellow Card No.E80276(N)
File No.E80271
APPLICATION
General purpose inverter, servo drives and other motor controls
PACKAGE OUTLINES
Dimensions in mm
110±1
95±0.5
Screwing depth
Min9.0
3-2
3-2
3-2
6-2
17.02
3.22
10
10
10
4-φ5.5
MOUNTING HOLES
Terminal code
1. VUPC 11. WP
1 2 3 4
5 6 7 8
9
11
13
15 17 19
14 16 18
10 12
2. UFO
3. UP
12. VWP1
13. VNC
4. VUP1 14. VN1
5. VVPC 15. Br
6. VFO
7. VP
16. UN
17. VN
8. VVP1 18. WN
9. VWPC 19. Fo
10. WFO
12
φ2.54
W
V
U
3-2
3.22
0.5±0.3
4-R6
0.5
21.2
24.5
26
26
22+–01..50
6-M5NUTS
2-φ2.54
66.44
19- 0.5
A
A : DETAIL
LABEL
Jul. 2005
MITSUBISHI <INTELLIGENT POWER MODULES>
PM75RSD060
FLAT-BASE TYPE
INSULATED PACKAGE
INTERNAL FUNCTIONS BLOCK DIAGRAM
Rfo=1.5kΩ
WP
VWP1
WFO
VP
VVP1
UP
VUP1
Br Fo
V
NC
W
N
V
N1
V
N
U
N
VFO
UFO
VWPC
VVPC
VUPC
Rfo
Rfo
Rfo
Rfo
Gnd In Fo Vcc Gnd In Fo Vcc Gnd In Fo Vcc
Gnd In Fo Vcc Gnd In Fo Vcc Gnd In Fo Vcc Gnd In Fo Vcc
Gnd
Gnd
Gnd
Gnd
Gnd
Gnd
Gnd
Si Out
Si Out
Si Out
Si Out
Si Out
Si Out
Si Out
Th
B
N
W
V
U
P
MAXIMUM RATINGS (Tj = 25°C, unless otherwise noted)
INVERTER PART
Symbol
VCES
±IC
Parameter
Collector-Emitter Voltage
Collector Current
Condition
Ratings
Unit
V
VD = 15V, VCIN = 15V
TC = 25°C
600
75
A
±ICP
PC
Collector Current (Peak)
Collector Dissipation
Junction Temperature
TC = 25°C
150
A
TC = 25°C
255
W
°C
Tj
–20 ~ +150
BRAKE PART
Symbol
Parameter
Condition
Ratings
Unit
V
VCES
IC
Collector-Emitter Voltage
Collector Current
VD = 15V, VCIN = 15V
TC = 25°C
600
30
A
ICP
PC
Collector Current (Peak)
Collector Dissipation
TC = 25°C
60
A
TC = 25°C
176
W
V
VR(DC)
IF
FWDi Rated DC Reverse Voltage TC = 25°C
600
FWDi Forward Current
Junction Temperature
TC = 25°C
30
A
Tj
–20 ~ +150
°C
CONTROL PART
Symbol
Parameter
Supply Voltage
Condition
Ratings
20
Unit
V
Applied between : VUP1-VUPC
VVP1-VVPC, VWP1-VWPC, VN1-VNC
Applied between : UP-VUPC, VP-VVPC
VD
VCIN
20
V
Input Voltage
WP-VWPC, UN • VN • WN • Br-VNC
Applied between : UFO-VUPC, VFO-VVPC, WFO-VWPC
FO-VNC
VFO
IFO
Fault Output Supply Voltage
Fault Output Current
20
20
V
Sink current at UFO, VFO, WFO, FO terminals
mA
Jul. 2005
MITSUBISHI <INTELLIGENT POWER MODULES>
PM75RSD060
FLAT-BASE TYPE
INSULATED PACKAGE
TOTAL SYSTEM
Ratings
Unit
Symbol
Parameter
Condition
Supply Voltage Protected by
OC & SC
VD = 13.5 ~ 16.5V, Inverter Part,
Tj = 125°C Start
400
500
V
V
VCC(PROT)
VCC(surge) Supply Voltage (Surge)
Applied between : P-N, Surge value or without switching
Module Case Operating
Temperature
TC
(Note-1)
–20 ~ +100
°C
Storage Temperature
Isolation Voltage
Tstg
Viso
–40 ~ +125
°C
60Hz, Sinusoidal, Charged part to Base, AC 1 min.
2500
Vrms
(Note-1) Tc measurement point is as shown below. (Base plate depth 3mm)
W
V
U
Tc
63mm
THERMAL RESISTANCES
Limits
Typ.
—
Test Condition
Symbol
Unit
Parameter
Min.
—
—
—
—
—
—
—
—
—
Max.
0.49
1.38
0.71
1.66
0.30
0.47
0.45
0.96
0.027
Inverter IGBT part (per 1 element), (Note-1)
Inverter FWDi part (per 1 element), (Note-1)
Brake IGBT part, (Note-1)
Rth(j-c)Q
Rth(j-c)F
Rth(j-c)Q
Rth(j-c)F
Rth(j-c’)Q
Rth(j-c’)F
Rth(j-c’)Q
Rth(j-c’)F
Rth(c-f)
—
—
Junction to case Thermal
Resistances
Brake FWDi part, (Note-1)
—
Inverter IGBT part (per 1 element), (Note-2)
Inverter FWDi part (per 1 element), (Note-2)
Brake IGBT part, (Note-2)
°C/W
—
—
—
Brake FWDi part, (Note-2)
—
Case to fin, Thermal grease applied (per 1 module)
Contact Thermal Resistance
—
(Note-2) TC measurement point is just under the chips.
If you use this value, Rth(f-a) should be measured just under the chips.
ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted)
INVERTER PART
Limits
Typ.
1.7
1.7
2.2
1.2
0.15
0.4
2.4
0.6
—
Unit
Test Condition
Symbol
VCE(sat)
Parameter
Collector-Emitter
Min.
—
Max.
2.3
2.3
3.3
2.4
0.3
1.0
3.3
1.2
1
VD = 15V, IC = 75A
VCIN = 0V, Pulsed
Tj = 25°C
(Fig. 1) Tj = 125°C
–IC = 75A, VD = 15V, VCIN = 15V
V
V
Saturation Voltage
—
(Fig. 2)
—
VEC
ton
FWDi Forward Voltage
0.8
—
VD = 15V, VCIN = 15V↔0V
VCC = 300V, IC = 75A
trr
µs
—
tc(on)
toff
Switching Time
Tj = 125°C
—
Inductive Load (upper and lower arm)
(Fig. 3)
—
tc(off)
Collector-Emitter
Cutoff Current
Tj = 25°C
Tj = 125°C
—
ICES
V
CE = VCES, VCIN = 15V
(Fig. 4)
mA
—
—
10
Jul. 2005
MITSUBISHI <INTELLIGENT POWER MODULES>
PM75RSD060
FLAT-BASE TYPE
INSULATED PACKAGE
BRAKE PART
Limits
Unit
Test Condition
Symbol
Parameter
Min.
—
Typ.
1.8
1.9
2.5
—
Max.
2.5
2.6
3.5
1
Collector-Emitter
VD = 15V, IC = 30A
VCIN = 0V, Pulsed
IF = 30A
Tj = 25°C
VCE(sat)
VFM
V
V
Saturation Voltage
FWDi Forward Voltage
Collector-Emitter
Cutoff Current
—
(Fig. 1)
Tj = 125°C
(Fig. 2)
—
Tj = 25°C
—
V
CE = VCES, VCIN = 15V
(Fig. 4)
ICES
mA
Tj = 125°C
—
—
10
CONTROL PART
Limits
Typ.
44
Symbol
Parameter
Circuit Current
Test Condition
VD = 15V, VCIN = 15V
Unit
mA
V
Min.
—
Max.
60
VN1-VNC
ID
VXP1-VXPC
—
13
18
Input ON Threshold Voltage
Input OFF Threshold Voltage
Vth(ON)
Applied between : UP-VUPC, VP-VVPC, WP-VWPC
1.2
1.7
—
1.5
2.0
—
1.8
2.3
380
320
—
UN • VN • WN • Br-VNC
Vth(OFF)
Tj = –20°C
Inverter part
VD = 15V
Tj = 25°C
192
115
226
—
(Fig. 5,6)
Over Current Trip Level
A
OC
Tj = 125°C
Break part
39
53
—
–20 ≤ Tj ≤ 125°C, VD = 15V
(Fig. 5,6)
Inverter part
Brake part
—
—
241
79
—
—
Short Circuit Trip Level
SC
–20≤ Tj ≤ 125°C, VD = 15V (Fig. 5,6)
A
µs
°C
Over Current Delay Time
Over Temperature Protection
toff(OC)
OT
—
10
—
VD = 15V
Base-plate
(Fig. 5,6)
Trip level
111
—
118
100
12.0
12.5
—
125
—
Temperature detection, VD = 15V
Reset level
Trip level
OTr
Supply Circuit Under-Voltage
Protection
UV
11.5
—
12.5
—
–20 ≤ Tj ≤ 125°C
VD = 15V, VFO = 15V
VD = 15V
V
UVr
Reset level
IFO(H)
IFO(L)
—
0.01
15
Fault Output Current
(Note-3)
(Note-3)
mA
ms
—
10
Minimum Fault Output Pulse
Width
tFO
1.0
1.8
—
(Note-3) Fault output is given only when the internal OC, SC, OT & UV protection.
Fault output of OC, SC and UV protection operate by upper and lower arms.
Fault output of OT protection operate by lower arm.
Fault output of OC, SC protection given pulse.
Fault output of OT, UV protection given pulse while over level.
MECHANICAL RATINGS AND CHARACTERISTICS
Limits
Typ.
3.0
Test Condition
Unit
Parameter
Mounting torque
Symbol
Min.
2.5
2.5
—
Max.
3.5
3.5
—
—
—
—
Main terminal
Mounting part
screw : M5
screw : M5
N • m
3.0
Mounting torque
Weight
N • m
g
560
—
RECOMMENDED CONDITIONS FOR USE
Symbol Parameter
Supply Voltage
Test Condition
Recommended value
Unit
V
VCC
Applied across P-N terminals
≤ 400
Applied between : VUP1-VUPC, VVP1-VVPC
VWP1-VWPC, VN1-VNC
VD
Control Supply Voltage
15 ± 1.5
V
V
(Note-4)
Input ON Voltage
Input OFF Voltage
VCIN(ON)
Applied between : UP-VUPC, VP-VVPC, WP-VWPC
UN • VN • WN • Br-VNC
≤ 0.8
≥ 4.0
VCIN(OFF)
Using Application Circuit input signal of IPM, 3φ
kHz
µs
PWM Input Frequency
fPWM
tdead
≤ 20
sinusoidal PWM VVVF inverter
(Fig. 8)
(Fig. 7)
Arm Shoot-through
Blocking Time
For IPM’s each input signals
≥ 2.5
(Note-4) Allowable Ripple rating of Control Voltage : dv/dt ≤ ±5V/µs, 2Vp-p
Jul. 2005
MITSUBISHI <INTELLIGENT POWER MODULES>
PM75RSD060
FLAT-BASE TYPE
INSULATED PACKAGE
PRECAUTIONS FOR TESTING
1. Before appling any control supply voltage (VD), the input terminals should be pulled up by resistores, etc. to their corre-
sponding supply voltage and each input signal should be kept off state.
After this, the specified ON and OFF level setting for each input signal should be done.
2. When performing “OC” and “SC” tests, the turn-off surge voltage spike at the corresponding protection operation should not
be allowed to rise above VCES rating of the device.
(These test should not be done by using a curve tracer or its equivalent.)
P, (U,V,W,B)
P, (U,V,W)
IN
IN
Fo
Fo
Ic
–Ic
V
V
V
CIN
(15V)
V
CIN
(0V)
U,V,W, (N)
U,V,W,B, (N)
V
D
(all)
VD (all)
Fig. 1 VCE(sat) Test
Fig. 2 VEC, (VFM) Test
a) Lower Arm Switching
P
Fo
trr
Irr
VCE
Signal input
(Upper Arm)
V
15V)
CIN
Ic
U,V,W
(
Vcc
CS
90%
Fo
Signal input
(Lower Arm)
90%
V
CIN
N
P
10%
V
D
(all)
Fo
Ic
10%
10%
10%
b) Upper Arm Switching
tc (on)
tc (off)
Signal input
(Upper Arm)
V
CIN
V
CIN
U,V,W
Vcc
C
S
td (on)
tr
td (off)
tf
Fo
V
15V)
CIN
Signal input
(Lower Arm)
(
(ton= td (on) + tr)
(toff= td (off) + tf)
N
Ic
V
D
(all)
Fig. 3 Switching time Test circuit and waveform
P, (U,V,W,B)
A
V
CIN
IN
Fo
Pulse
V
CE
V
(15V)
CIN
Over Current
OC
U,V,W, (N)
I
C
VD (all)
toff (OC)
Constant Current
Fig. 4 ICES Test
P, (U,V,W,B)
Short Circuit Current
IN
Constant Current
V
CC
Fo
SC
V
CIN
I
C
U,V,W, (N)
(all)
V
D
IC
Fig. 5 OC and SC Test
Fig. 6 OC and SC Test waveform
P
VD
VCINP
U,V,W
Vcc
VD
V
CINN
CINP
N
Ic
V
0V
0V
t
t
V
CINN
t
dead
t
dead
t
dead
Fig. 7 Dead time measurement point example
Jul. 2005
MITSUBISHI <INTELLIGENT POWER MODULES>
PM75RSD060
FLAT-BASE TYPE
INSULATED PACKAGE
P
≥10µ
20k
VUP1
UFO
UP
Vcc
Fo
→
Rfo
Rfo
Rfo
OUT
Si
+
VD
IF
–
In
U
VUPC
GND GND
≥0.1µ
VVP1
VFO
Vcc
OUT
Fo
Si
VD
VD
VP
In
V
VVPC
GND GND
M
VWP1
WFO
Vcc
OUT
Fo
Si
WP
In
W
VWPC
GND GND
20k
Vcc
Fo
In
OUT
Si
→
≥10µ
IF
UN
GND GND
≥0.1µ
N
Th
20k
TEMP
Vcc
→
OUT
≥10µ
≥10µ
Fo
IF
Si
VN
In
GND GND
≥0.1µ
20k
VN1
WN
Vcc
→
OUT
Fo
IF
VD
Si
In
GND GND
B
≥0.1µ
VNC
4.7k
Vcc
OUT
Fo
Br
Si
In
GND GND
1k
5V
Rfo
Fo
: Interface which is the same as the U-phase
Fig. 8 Application Example Circuit
NOTES FOR STABLE AND SAFE OPERATION ;
Design the PCB pattern to minimize wiring length between opto-coupler and IPM’s input terminal, and also to minimize the
•
stray capacity between the input and output wirings of opto-coupler.
Quick opto-couplers: TPLH, TPLH ≤ 0.8µs. Use High CMR type. The line between opto-coupler and intelligent module
•
should be shortened as much as possible to minimize the floating capacitance.
Slow switching opto-coupler: recommend to use at CTR = 100 ~ 200%, Input current = 8 ~ 10mA, to work in active.
•
Use 4 isolated control power supplies (VD). Also, care should be taken to minimize the instantaneous voltage charge of the
•
power supply.
Make inductance of DC bus line as small as possible, and minimize surge voltage using snubber capacitor between P and N
•
terminal.
Use line noise filter capacitor (ex. 4.7nF) between each input AC line and ground to reject common-mode noise from AC line
•
and improve noise immunity of the system.
Jul. 2005
MITSUBISHI <INTELLIGENT POWER MODULES>
PM75RSD060
FLAT-BASE TYPE
INSULATED PACKAGE
PERFORMANCE CURVES (Inverter Part)
COLLECTOR-EMITTER SATURATION
OUTPUT CHARACTERISTICS
VOLTAGE (VS. Ic) CHARACTERISTICS
(TYPICAL)
(TYPICAL)
100
2
VD = 15V
T
j
= 25°C
15V
13V
80
60
40
20
0
VD = 17V
1.5
1
0.5
0
T
T
j
j
= 25°C
= 125°C
0
0.5
1
1.5
2
0
20
40
60
80
(A)
100
COLLECTOR-EMITTER VOLTAGE VCE (V)
COLLECTOR CURRENT I
C
COLLECTOR-EMITTER SATURATION
VOLTAGE (VS. V
D
) CHARACTERISTICS
SWITCHING TIME CHARACTERISTICS
(TYPICAL)
(TYPICAL)
2
1.5
1
101
7
V
V
CC = 300V
= 15V
D
5
4
3
T
T
j
= 25°C
= 125°C
j
Inductive load
2
100
7
t
c(off)
c(on)
c(off)
t
t
5
4
3
0.5
0
IC = 75A
t
c(on)
2
2
T
T
j
= 25°C
= 125°C
j
10–1
12
13
14
15
16
17
18
(V)
101
3
4 5
7
102
2
3
4 5
(A)
7
103
CONTROL SUPPLY VOLTAGE V
D
COLLECTOR CURRENT I
C
SWITCHING TIME CHARACTERISTICS
(TYPICAL)
SWITCHING LOSS CHARACTERISTICS
(TYPICAL)
101
101
7
7
E
SW(off)
5
4
5
4
3
3
t
off
on
2
2
t
100
7
100
7
5
4
3
5
4
3
E
SW(on)
V
V
CC = 300V
= 15V
V
V
CC = 300V
D = 15V
D
T
T
j
= 25°C
= 125°C
T
T
j
= 25°C
= 125°C
2
2
j
j
Inductive load
Inductive load
10–1
10–1
101
2
3
4 5
7
102
2
3
4 5
7
103
101
2
3
4 5
7
102
2
3
4 5 7
103
COLLECTOR CURRENT I
C
(A)
COLLECTOR CURRENT IC (A)
Jul. 2005
MITSUBISHI <INTELLIGENT POWER MODULES>
PM75RSD060
FLAT-BASE TYPE
INSULATED PACKAGE
DIODE FORWARD CHARACTERISTICS
(TYPICAL)
DIODE REVERSE RECOVERY CHARACTERISTICS
(TYPICAL)
102
100
102
VD = 15V
7
7
7
5
4
5
4
5
4
3
3
3
I
rr
2
2
2
101
7
10–1
7
101
7
t
rr
5
4
3
5
4
3
5
4
3
V
V
CC = 300V
= 15V
D
T
T
j
= 25°C
= 125°C
2
2
2
T
T
j
j
= 25°C
= 125°C
j
Inductive load
100
100
10–2
0
0.5
1
1.5
2
2.5
101
2
3
4 5
7
102
2
3
4 5 7
103
–
IC (A)
EMITTER-COLLECTOR VOLTAGE VEC (V)
COLLECTOR RECOVERY CURRENT
TRANSIENT THERMAL
I
D
VS. f
c
CHARACTERISTICS
(TYPICAL)
IMPEDANCE CHARACTERISTICS
(IGBT PART)
100
80
60
40
20
0
101
7
VD = 15V
= 25°C
5
T
j
3
2
100
7
5
3
N-side
2
10–1
7
5
3
2
10–2
7
5
P-side
Single Pulse
Per unit base = Rth(j – c)Q = 0.49°C/W
3
2
10–3
10–32 3 5 710–22 3 5 710–12 3 5 7100 2 3 57101
0
5
10
15
20
(kHz)
25
CARRIER FREQUENCY f
c
TIME (s)
TRANSIENT THERMAL
IMPEDANCE CHARACTERISTICS
(FWDi PART)
101
7
5
3
2
100
7
5
3
2
10–1
7
5
3
2
10–2
7
5
3
2
Single Pulse
Per unit base = Rth(j – c)F = 1.38°C/W
10–3
10–32 3 5 710–22 3 5 710–12 3 5 7100 2 3 57101
TIME (s)
Jul. 2005
MITSUBISHI <INTELLIGENT POWER MODULES>
PM75RSD060
FLAT-BASE TYPE
INSULATED PACKAGE
PERFORMANCE CURVES (Brake Part)
OUTPUT CHARACTERISTICS
(TYPICAL)
COLLECTOR-EMITTER SATURATION
VOLTAGE (VS. Ic) CHARACTERISTICS
(TYPICAL)
40
2.5
2
T
j
= 25°C
15V
30
VD = 17V
13V
1.5
20
10
0
1
VD = 15V
0.5
0
T
T
j
j
= 25°C
= 125°C
0
0.5
1
1.5
2
2.5
0
10
20
30
40
COLLECTOR-EMITTER VOLTAGE VCE (V)
COLLECTOR CURRENT IC (A)
COLLECTOR-EMITTER SATURATION
VOLTAGE (VS. V
D
) CHARACTERISTICS
DIODE FORWARD CHARACTERISTICS
(TYPICAL)
(TYPICAL)
102
2.5
2
7
VD = 15V
5
4
3
T
T
j
= 25°C
= 125°C
j
2
1.5
1
101
7
5
4
3
0.5
0
IC = 30A
2
T
T
j
= 25°C
= 125°C
j
100
12
13
14
15
16
17
18
(V)
0
0.5
1
1.5
2
2.5
3
CONTROL SUPPLY VOLTAGE V
D
EMITTER-COLLECTOR VOLTAGE VEC (V)
TRANSIENT THERMAL
IMPEDANCE CHARACTERISTICS
(IGBT PART)
TRANSIENT THERMAL
IMPEDANCE CHARACTERISTICS
(FWDi PART)
101
7
101
7
5
5
3
3
2
2
100
7
100
7
5
5
3
3
2
2
10–1
10–1
7
5
7
5
3
3
2
2
10–2
10–2
7
5
7
5
Single Pulse
Per unit base = Rth(j – c)Q = 0.71°C/W
Single Pulse
Per unit base = Rth(j – c)F = 1.66°C/W
3
2
3
2
10–3
10–3
10–32 3 5 710–22 3 5 710–12 3 5 7100 2 3 57101
10–32 3 5 710–22 3 5 710–12 3 5 7100 2 3 57101
TIME (s)
TIME (s)
Jul. 2005
相关型号：
PM75RSD120
Intellimod⑩ Module Three Phase Brake IGBT Inverter Output (75 Amperes/1200 Volts)
POWEREX
©2020 ICPDF网 联系我们和版权申明