0621009760 [MOLEX]

Tool And Machinery,;


型号：	0621009760
厂家：	Molex
描述：	Tool And Machinery, 连接器连接器支架
文件：	总4页 (文件大小：538K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Impel Daughtercard Removal Tool

IMPEL

Daughtercard

Module

Removal Tool

Application Tooling

Specification Sheet

Order No. 62100-9760

FEATURES

This tool is designed for the removal of an IMPEL Daughtercard module

Removes Module without damage to the PCB

Use tool 62201-8923 for inserting 6 Pair by 16 column Daughtercard assemblies

SCOPE

Products: IMPEL Daughtercard signal module, 6 Pair by 16 columns (1.9mm pitch). See Product List below for

order numbers.

Product List

The following is a partial list of the product order numbers and their specifications this tool is designed to run.

Updates to this list are available on www.molex.com.

Series No. Guide Style Columns

Assembly Order Number

Unguided

171400-1026

171400-3026 171400-3126 171400-3226 171400-3326 171400-3426 171400-3526

171400-3626 171400-3726 171400-3826

Left

171400

171400-5026 171400-5126 171400-5226 171400-5326 171400-5426 171400-5526

171400-5626 171400-5726 171400-5826

Right

WING KNOB

DESCRIPTION

Figure 1 illustrates the principal

parts of the removal tool.

C-FRAME

THUMB

SCREW

EXTENSION

PADS (2)

CLAMP REAR

Figure 1

CLAMP FRONT

Doc No: ATS-621009760

Revision: A

Release Date: 11-25-13

Revision Date: 11-25-13

UNCONTROLLED COPY

Page 1 of 4

Impel Daughtercard Removal Tool

SIGNAL MODULE

Tool Restrictions

5.0mm

MINIMUM

These tools require a “Keep Out Zone” around the Module

free of components. The rear of the Module should be

5.00mm (.197”). The right and left sides should be 5.00mm

(.197”). See Figure 2. This is a general requirement,

regardless of the module being removed.

5.0mm

MINIMUM

(BOTH SIDES)

Note: Be sure that all parts of the removal tool will clear any

components on the printed circuit board during use. Tape

may also be placed over circuit traces or on the bottom of the

PCB Support for added protection of the printed circuit board.

PCB

KEEP OUT ZONE

Figure 2

Tool Operation

1. Turn the wing knob counter clockwise so the clamp rear and clamp front are approximately 4mm below the

bottom edge of the extension pads. See Figure 3.

TURN WING

KNOB CCW

TURN WING

LIFTING

SCREW

KNOB CCW

TURN THUMB

SCREW CCW

EXTENSION

PAD

4mm

TURN THUMB

SCREW CCW

Figure 4

CLAMP

FRONT

CLAMP

FRONT

CLAMP REAR

Figure 3

2. Turn the thumb screw counter clockwise so the clamp front can slide forward shown in Figure 4.

3. Position the extractor tool over the outside walls of the Daughtercard module. See figure 5.

FRONT OF

MODULE

CLAMP

REAR

FRONT

Figure 5

Doc No: ATS-621009760

Revision: A

Release Date: 11-25-13

Revision Date: 11-25-13

UNCONTROLLED COPY

Page 2 of 4

Impel Daughtercard Removal Tool

4. Slide the clamp front onto the bottom lip of the front module by turning the thumb screw clockwise. See

Figure 6.

5. Continue turning the thumb screw until the clamp rear is pulled into position and is seated in the recessed

slots of the clamp rear.

KNOB TURNED

CLOCKWISE

TURN

THUMB SCREW

CLOCKWISE

EXTENSION

PAD RESTING

ON THE PCB

PCB

CLAMP REAR

IN HOUSING

SLOTS

Figure 6

Figure 7

HOUSING RESTING ON

THE CLAMP FRONT

6. Make sure the clamp front and rear are in position before lifting the Daughtercard module off the PCB.

7. Turn the wing knob clockwise (CW) until the extension pads contact the printed circuit board. See Figure 7.

8. Continue turning the wing knob clockwise (CW) until the Daughtercard module is removed from the printed

circuit board.

9. Move the extraction tool away from the printed circuit board. Turn the wing knob counter-clockwise (CCW)

and turn the thumb screw counterclockwise (CCW) to release the module from the extractor tool. Discard

the module.

Note: After the Daughtercard module is removed from the PCB, some terminals may be left in the PCB. This is

not a tooling malfunction. If there are terminals left in the PCB use a pair of long nose pliers to remove them

carefully so no damage is caused to the PCB. Caution is required when using this method; if a terminal is

incorrectly gripped or pulled away at an angle, it could break off inside the PCB hole. After terminals are pulled out

of the PCB, they should be discarded. The PCB should be free of any contact debris.

M5 x 14 LONG

Daughtercard Module Assembly Removal

(With Module Assemblies on one side)

SHCS

C-FRAME

EXTENSION PAD

ROTATED 180º

THIS SIDE ONLY

When Daughtercard modules are stacked end to end on one side

the extrator tool can be converted to allow the removal of the

desired daughtercard module.

1. Remove the M5 x 14 long SHCS on the side where the extra

module is located. See Figure 8.

2. Rotate the extension pad 180º.

MODULE

ASSEMBLY

3. Reinstall the M5 x 14 long SHCS thru the hole near the end of

the C-frame.

4. Follow the tool operation for removal.

Figure 8

Doc No: ATS-621009760

Revision: A

Release Date: 11-25-13

Revision Date: 11-25-13

UNCONTROLLED COPY

Page 3 of 4

Impel Daughtercard Removal Tool

M5 x 14 LONG

SHCS

M5 x 14 LONG

SHCS

Daughtercard Module Assembly Removal

(With Module Assemblies on both sides)

When Daughtercard modules are stacked end to end

on both sides the extrator tool can be converted to

allow the removal of the desired daughtercard module.

C-FRAME

EXTENSION

PAD

ROTATED

EXTENSION PAD

ROTATED 180º

1. Remove the M5 x 14 long SHCS on each the side

where the extra modules are located. See

Figure 9.

180º

MODULE

ASSEMBLY

MODULE

ASSEMBLY

2. Rotate the extension pads 180º.

3. Reinstall the M5 x 14 long SHCS thru the hole near

the end of the C-frame.

Figure 9

4. Follow the tool operation for removal.

Daughtercard Guided Module Assembly Removal

When removing a Daughtercard with a Guide module the extractor tool can be converted as follows:.

M5 x 14 LONG

1. Remove the M5 x 14 long SHCS on the side where the guide

module is located.

SHCS

2. Move the extension pad out on this side. See Figure 10.

3. Align the second threaded hole in the extension pad with the C-

frame.

4. Reinstall the M5 x 14 long SHCS thru the hole near the end of

the C-frame.

C-FRAME

EXTENSION PAD

MOVED OUT

NOTE: Remove the screw holding the guide module to the PCB

before removing the Daughtercard module.

GUIDE MODULE

ASSEMBLY

5. Follow the tool operation for removal.

Figure 10

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible for, the following

maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality

machine oil. Do not oil excessively.

4. When tool is not in use, store in a clean, dry area.

CAUTION: Molex specifications are valid only when used with Molex terminals, applicators and tooling.

Contact Information

For more information on Molex application tooling please contact Molex at 1-800-786-6539.

Visit our Web site at http://www.molex.com

Doc No: ATS-621009760

Revision: A

Release Date: 11-25-13

Revision Date: 11-25-13

UNCONTROLLED COPY

Page 4 of 4

0621009760 [MOLEX]

相关型号：

0621009780

0621009790

0621009800

0621009810

0621601000808+

0621601001808+

06216010100808+

06216010101808+

06216010110808+

06216010111808+

06216010111808A+

0621601101808+