0622018840 [MOLEX]
Tool And Machinery,;型号: | 0622018840 |
厂家: | Molex |
描述: | Tool And Machinery, 连接器 连接器支架 |
文件: | 总3页 (文件大小:189K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Impact™ Daughtercard Press-In Tool
Impact™
Daughtercard
Module Installation
Press-In Tool
Application Tooling
Specification Sheet
Order No. 62201-8840
FEATURES
°
°
°
Lip provided for positive alignment to connector assembly.
Tool provides uniform distribution of press force across entire pin array.
May be used as a stand-alone tool or mounted in an optional holder with other Molex press-in tools.
SCOPE
Products: Impact™ Daughtercard 85 Ohm Assembly 170340 Series, (4-Pair by 14 Column Assemblies). See
Product List below for specific part numbers.
Product List
The following is a partial list of the product order numbers and their specifications this tool is designed to run.
Updates to this list are available on www.molex.com.
Series No. Guide Style Columns
Assembly Order Number
Open
14
170340-1014 170340-1024
170340-3014 170340-3024 170340-3114 170340-3124 170340-3214 170340-3224
170340-3314 170340-3324 170340-3414 170340-3424 170340-3514 170340-3524
170340-3614 170340-3624 170340-3714 170340-3724 170340-3814 170340-3824
170340-5014 170340-5024 170340-5114 170340-5124 170340-5214 170340-5224
170340-5314 170340-5324 170340-5414 170340-5424 170340-5514 170340-5524
170340-5614 170340-5624 170340-5714 170340-5724 170340-5814 170340-5824
Left
14
170340
Right
14
WITH 62201-95XX
RAIL
Tool Setup
Depending on the number of connectors to be installed
and/or the press used, this tool can be used alone or with
a group of press-in tools, mounted in a 62201-95XX rail
(ordered separately). See Figure 1.
ALONE
Figure 1
Doc No: ATS-6220188408
Revision: A
Release Date: 12-13-13
Revision Date: 12-13-13
UNCONTROLLED COPY
Page 1 of 3
Impact™ Daughtercard Press-In Tool
Tool Installation
The 62201-95XX rail is available in a variety of lengths to accommodate multiple press-in tools.
Rail Part Number Rail Overall Length
62201-9501
62201-9502
62201-9503
62201-9504
62201-9509
62201-9511
24mm (0.94 in)
72mm (2.83 in)
156mm (6.14 in)
216mm (8.50 in)
254mm (10.0 in)
305mm (12.0 in)
Reference: This Press-In Tool is 26.46mm (1.04 in.) long.
Printed Circuit Board (PCB) Support
The Impact™ connectors require up to 3.6kg (8 lb) of force per pin to press into the PCB. To prevent excessive
PCB flexure and/or damage to the PCB, a support plate is strongly recommended directly beneath the connector
hole pattern.
Due to the custom nature of every application, Molex does not offer any PCB support plate. The customer must
furnish their own support plate.
When creating the PCB support plate, remember to allow clearance for the connector pins as they pass through
the PCB thickness.
Press Equipment Recommendations
Many types of presses can be used to install Impact™ connectors, but to assure consistent connector installation
Molex recommends the following press criteria:
1. The capability to detect force variations as low as 4.5kg (10 lb) during the press-in cycle; excessive force
measurements should stop the press-in cycle.
2. The rate of pressing can be regulated as low as 0.13mm (0.005 in) per second.
3. Press stroke control to within 0.25mm (0.010 in).
4. Total press stroke must be at least 19mm (0.75 in).
5. For statistical purposes, automatic collection of force
GUIDE SURFACE
and distance data.
Tool Operation
1. Carefully insert, by hand, the Daughtercard
module(s) into the PCB hole pattern.
2. Place the application tool on top of the Daughtercard
module with the back guide surface of the tool
against the back of the Daughtercard module. See
Figure 2.
Figure 2
Doc No: ATS-6220188408
Revision: A
Release Date: 12-13-13
Revision Date: 12-13-13
UNCONTROLLED COPY
Page 2 of 3
Impact™ Daughtercard Press-In Tool
3. Using the application tool and an appropriate press, seat the Daughtercard module until there is less than
0.10mm (.004 in) clearance between the bottom of the plastic housing and the surface of the PCB. See
Figure 3.
0.10
.004
MAXIMUM
Figure 3
There should be no broken stand-offs along the perimeter of the part (an indication of over-pressing).
CAUTION: To prevent injury, never operate any press without the guards in place. Refer to the press
manufacturer’s instruction manual.
CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling.
Contact Information
For more information on Molex application tooling please contact Molex at 1-800-786-6539.
http://www.molex.com
Doc No: ATS-6220188408
Revision: A
Release Date: 12-13-13
Revision Date: 12-13-13
UNCONTROLLED COPY
Page 3 of 3
相关型号:
©2020 ICPDF网 联系我们和版权申明