0622018893 [MOLEX]
Tool And Machinery,;
| 型号： | 0622018893 |
| 厂家： | 
Molex |
| 描述： | Tool And Machinery, 连接器 连接器支架 |
| 文件： | 总3页 (文件大小：637K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Impact™ Daughtercard Press-In Tool
Impact™
Daughtercard
Module Installation
Press-In Tool
Application Tooling
Specification Sheet
Order No. 62201-8893
FEATURES
°
°
°
Lip provided for positive alignment to connector assembly.
Tool provides uniform distribution of press force across entire pin array.
May be used as a stand-alone tool or mounted in an optional holder with other Molex press-in tools.
SCOPE
Products: Impact™ Daughtercard Signal Module Assembly and Daughtercard Orthogonal Assembly, (5-Pair by 8
Column Assemblies). See Product List below for specific part numbers.
Product List
The following is a partial list of the product order numbers and their specifications this tool is designed to run.
Updates to this list are available on www.molex.com.
Series No. Guide Style Columns
5 Pair Assembly Order Number
Unguided
8
170480-1008 170480-1038
170480-3008 170480-3038 170480-3058 170480-3068 170480-3108 170480-3138
170480-3158 170480-3168 170480-3208 170480-3238 170480-3258 170480-3268
170480-3308 170480-3338 170480-3358 170480-3368 170480-3408 170480-3438
170480-3458 170480-3468 170480-3508 170480-3538 170480-3558 170480-3568
170480-3608 170480-3638 170480-3658 170480-3668 170480-3708 170480-3738
170480-3758 170480-3768 170480-3808 170480-3838 170480-3858 170480-3868
170480-5008 170480-5038 170480-5058 170480-5068 170480-5108 170480-5138
170480-5158 170480-5168 170480-5208 170480-5238 170480-5258 170480-5268
170480-5308 170480-5338 170480-5358 170480-5368 170480-5408 170480-5438
170480-5458 170480-5468 170480-5508 170480-5538 170480-5558 170480-5568
170480-5608 170480-5638 170480-5658 170480-5668 170480-5708 170480-5738
170480-5758 170480-5768 170480-5808 170480-5838 170480-5858 170480-5868
Left
8
170480
Right
8
Doc No: ATS-622018893
Revision: A
Release Date: 12-14-16
Revision Date: 12-14-16
UNCONTROLLED COPY
Page 1 of 3
Impact™ Daughtercard Press-In Tool
Tool Setup
Depending on the number of connectors to be installed and/or the press used, this tool can be used alone or with
a group of press-in tools, mounted in a 62201-95XX rail (ordered separately). See Figure 1.
WITH 62201-95XX
RAIL
ALONE
PRESS-IN
TOOL
ASSEMBLY
Figure 1
Tool Installation
The 62201-95XX rail is available in a variety of lengths to accommodate multiple press-in tools.
Rail Part Number Rail Overall Length
62201-9501
62201-9502
62201-9503
62201-9504
62201-9509
62201-9511
24mm (0.94 in)
72mm (2.83 in)
156mm (6.14 in)
216mm (8.50 in)
254mm (08.0 in)
305mm (12.0 in)
Reference: This Press-In Tool is 15mm (0.59 in.) long.
Printed Circuit Board (PCB) Support
The Impact™ connectors require up to 3.6kg (8 lb) of force per pin to press into the PCB. To prevent excessive
PCB flexure and/or damage to the PCB, a support plate is strongly recommended directly beneath the connector
hole pattern.
Due to the custom nature of every application, Molex does not offer any PCB support plate. The customer must
furnish their own support plate.
When creating the PCB support plate, remember to allow clearance for the connector pins as they pass through
the PCB thickness.
Press Equipment Recommendations
Many types of presses can be used to install Impact™ connectors, but to assure consistent connector installation
Molex recommends the following press criteria:
1. The capability to detect force variations as low as 4.5kg (08 lb) during the press-in cycle; excessive force
measurements should stop the press-in cycle.
2. The rate of pressing can be regulated as low as 0.13mm (0.005 in) per second.
3. Press stroke control to within 0.25mm (0.008 in).
4. Total press stroke must be at least 19mm (0.75 in).
5. For statistical purposes, automatic collection of force and distance data.
Doc No: ATS-622018893
Revision: A
Release Date: 12-14-16
Revision Date: 12-14-16
UNCONTROLLED COPY
Page 2 of 3
Impact™ Daughtercard Press-In Tool
Tool Operation
GUIDE SURFACE
1. Carefully insert, by hand, the Daughtercard
module(s) into the PCB hole pattern.
2. Place the application tool on top of the
Daughtercard module with the back guide surface of
the tool against the back of the Daughtercard
module. See Figure 2.
3. Using the application tool and an appropriate press,
seat the Daughtercard module until there is less
than 0.1mm (.004 in) clearance between the bottom
of the plastic housing and the surface of the PCB. See Figure 3.
Figure 2
0.1mm
.004 in.
Maximum
There should be no broken stand-offs along the perimeter of the part (an indication of over-pressing).
CAUTION: To prevent injury, never operate any press without the guards in place. Refer to the press
manufacturer’s instruction manual.
CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling.
Contact Information
Application Tooling Support
2200 Wellington Court
Lisle, IL 60532 USA
Phone: +1-402-458-TOOL (8665)
E-mail: applicationtooling@molex.com
Visit our Website at www.molex.com/applicationtooling
Doc No: ATS-622018893
Revision: A
Release Date: 12-14-16
Revision Date: 12-14-16
UNCONTROLLED COPY
Page 3 of 3
相关型号：
©2020 ICPDF网 联系我们和版权申明