0622031300 [MOLEX]

Tool And Machinery,;


型号：	0622031300
厂家：	Molex
描述：	Tool And Machinery, 连接器连接器支架
文件：	总3页 (文件大小：250K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

NeoPress Plug Press-In Tool

NeoPress

Plug Assembly

Press-In Tool

Application Tooling

Specification Sheet

Order No. 62203-1300

FEATURES

Tool provides uniform distribution of press force across entire pin array

May be used as a stand-alone tool or mounted in an optional holder with other Molex press-in tools

For plug extraction, use tool 62203-1320

SCOPE

Products: NeoPress Plug Assembly, (6-Pair by 14 Column Assemblies).

See Product List below for specific part numbers.

Product List

The following is a partial list of the product order numbers and their specifications this tool is designed to run.

Updates to this list are available on www.molex.com.

Series No. Column Height Plug Assembly Order No.

172801

13.5mm

172801-0001

Tool Setup

Depending on the number of connectors to be installed and/or the press used, this tool can be used alone or with

a group of press-in tools, mounted in a 62201-95XX rail (ordered separately). See Figure 1.

WITH 62201-95XX

RAIL

PRESS-IN

TOOL

PRESS-IN

TOOL

ALONE

PLUG

ASSEMBLY

Figure 1

Doc No: ATS-622031300

Revision: A

Release Date: 01-06-15

Revision Date: 06-09-17

UNCONTROLLED COPY

Page 1 of 3

NeoPress Plug Press-In Tool

Tool Installation

The 62201-95XX rail is available in a variety of lengths to accommodate multiple press-in tools.

Rail Part Number Rail Overall Length

62201-9502

62201-9503

62201-9504

62201-9509

62201-9511

72mm (2.83 in)

156mm (6.14 in)

216mm (8.50 in)

254mm (10.0 in)

305mm (12.0 in)

Reference: The 62203-1300 Press-In Tool is 60mm (2.36 in.) long.

Printed Circuit Board (PCB) Support

The NeoPress plug requires a significant force to press the assembly into the PCB. To prevent excessive PCB

flexure and/or damage to the PCB, a support plate is strongly recommended directly beneath the connector hole

pattern.

Due to the custom nature of every application, Molex does not offer any PCB support plate. The customer must

furnish their own support plate.

When creating the PCB support plate, remember to allow clearance for the connector pins as they pass through

the PCB thickness.

Press Equipment Recommendations

Many types of presses can be used to install the NeoPress plug, but to assure consistent connector installation

Molex recommends the following press criteria:

1. The capability to detect force variations as low as 4.5kg (10 lb) during the press-in cycle; excessive force

measurements should stop the press-in cycle.

2. The rate of pressing can be regulated as low as 0.13mm (0.005 in) per second.

PRESS-IN TOOL

3. Press stroke control to within 0.25mm (0.010 in).

4. Total press stroke must be at least 19mm (0.75 in).

5. For statistical purposes, automatic collection of

force and distance data.

Tool Operation

1. By hand, insert the plug assembly carefully into the

PCB hole pattern. Make sure the connector is

oriented properly by confirming the location of the

#1 circuit indicator with respect to the PCB layout.

PCB

Figure 2

PLUG ASSEMBLY

2. Insert the Press-In Tool over the top of the connector housing until it rests on the connector. The tool is

symmetric and can be placed two ways without damage to the connector. See Figure 2.

Doc No: ATS-622031300

Revision: A

Release Date: 01-06-15

Revision Date: 06-09-17

UNCONTROLLED COPY

Page 2 of 3

NeoPress Plug Press-In Tool

3. Using the application tool and an appropriate press, seat the plug assembly until there is less than 0.10mm

(.004 in) clearance between the bottom of the plastic housing and the surface of the PCB. See Figure 3.

0.10

.004

MAX.

Figure 3

PCB

CAUTION: To prevent injury, never operate any press without the guards in place. Refer to the press

manufacturer’s instruction manual.

CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling.

Application Tooling Support

Phone: (402) 458-TOOL (8665)

E-Mail: applicationtooling@molex.com

Website: www.molex.com/applicationtooling

Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks

listed herein belong to their respective owners.

Doc No: ATS-622031300

Revision: A

Release Date: 01-06-15

Revision Date: 06-09-17

UNCONTROLLED COPY

Page 3 of 3

0622031300 [MOLEX]

相关型号：

0622035240

0622035260

0622601001800+

0622601002800+

0622601101800+

0622601102800+

0622601103800+

0622601201800+

0622601202800+

0622601302800+

0622601303800+

0622601501800+