0638132250 [MOLEX]
MODULE CARD EXTRACT;
| 型号： | 0638132250 |
| 厂家： | 
Molex |
| 描述： | MODULE CARD EXTRACT 连接器 连接器支架 |
| 文件： | 总3页 (文件大小：320K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Tall Modular Card Extractor Tool
Tall
Module Card
Extractor Tool
Application Tooling
Specification Sheet
Order No. 63813-2250
FEATURES
%
This tool is designed for the removal of the memory module card from the metal latch 78049 series Molex
sockets, 1mm pitch, 188-circuit vertical press-fit with metal latch DDR2.
SCOPE
Products: 78049 Series 188 Circuit Low Profile Metal Latch DDR2 Dimm Connector System. See Product List
below for specific part numbers.
Product List
The following is a partial list of the product order numbers and their specifications this tool is designed to run.
Updates to this list are available on www.molex.com.
Assembly Order Number
Description
78049-0011
78049-0021
78049-0012
78049-0022
1.00mm (.039") Pitch DDR-2 DIMM Socket, Vertical,
Press-fit, 188 Circuits Metal Latch
DESCRIPTION
THUMB
PUSHER
The 1mm pitch, 188-circuit low profile metal latch DDR2 takes up
a much smaller space inside the housing than a conventional
latch will. The entire connector length is almost similar to the
module card. However, the latch cannot be extracted by hand
and this extraction tool is required to withdrawal the module card
from the metal latch.
HANDLE
The Module Card Extractor Tool consists of modular card latch,
metal latch, and thumb pusher with a handle.
METAL LATCH
PUSHER
MODULE
CARD
LATCH
Figure 1
Doc No: ATS-638132250
Revision: A
Release Date: 01-31-14
Revision Date: 01-31-14
UNCONTROLLED COPY
Page 1 of 3
Tall Modular Card Extractor Tool
Operation
1. Align the metal latch pushers (2) with the slots on the module card housing. See Figure 2.
2. Push the extractor tool down and into the slots. The module card latches are spring-loaded and will open
when extractor tool is engaged in the module card housing. See Figure 3.
EXTRACTOR
TOOL
METAL
LATCH
PUSHER
MODULE CARD
LATCHES OPEN
MODULE CARD
HOUSING
METAL
LATCH
PUSHER
PCB BOARD
MODULE HOUSING
MODULE CARD
METAL LATCH PUSHER
Figure 3
MODULE CARD Figure 2
3. Make sure the extractor tool is firmly seated in the slots of the module card housing and the module card
latches are locked into the module card.
LIFT UP BY
THE HANDLE
METAL
LATCH PUSHER
MODULE CARD
MODULE CARD
LATCHES LOCKED
IN PLACE
MODULE CARD
HOUSING
Figure 4
4. Pull the module card straight up with the handle of the extractor tool. See Figure 4.
Doc No: ATS-638132250
Revision: A
Release Date: 01-31-14
Revision Date: 01-31-14
UNCONTROLLED COPY
Page 2 of 3
Tall Modular Card Extractor Tool
5. When the module card is free of the housing, press down on the thumb pusher. This will open the module
card latches and release the card from the extractor tool. See Figure 5.
PUSH DOWN
ON THE THUMB
PUSHER
MODULE CARD
MODULE CARD
Figure 5
LATCHES WILL
RELEASE
Maintenance
It is recommended that each operator of the tool be made aware of, and responsible for, the following
maintenance steps:
1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality
machine oil. Do not oil excessively.
When tool is not in use, store in a clean, dry area.
CAUTION: Molex specifications are valid only when used with Molex terminals, applicators and tooling.
Molex does not offer repair parts for Extractor Tools due to the inexpensive nature of these tools.
Contact Information
For more information on Molex application tooling please contact Molex at 1-800-786-6539.
Visit our Web site at http://www.molex.com
Doc No: ATS-638132250
Revision: A
Release Date: 01-31-14
Revision Date: 01-31-14
UNCONTROLLED COPY
Page 3 of 3
相关型号：
©2020 ICPDF网 联系我们和版权申明