0638240900 [MOLEX]
Application Tooling Specification Sheet; 应用工具的规格表型号: | 0638240900 |
厂家: | Molex |
描述: | Application Tooling Specification Sheet |
文件: | 总2页 (文件大小:448K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Extractor Tool for CTX64 Receptacle Crimp Terminal
Extractor Tool
Application Tooling
Specification Sheet
Order No. 63824-0900
FEATURES
ꢀ
This Extractor Tool is for the removal of a CTX64 Receptacle Crimp Terminal (502306 Series) from a CMX
Connector (98833 Series).
SCOPE
Products: CTX64 Receptacle Crimp Terminal for CMX Connector.
Terminal
Series No.
Terminal Order No.
502306-0111 502306-0112 502306-0113 502306-0114 502306-0121 502306-0122 502306-0123
502306-0124 502306-0211 502306-0212 502306-0213 502306-0214 502306-0221 502306-0222
502306-0223 502306-0224 502306-1111 502306-1112 502306-1113 502306-1114 502306-1121
502306-1122 502306-1123 502306-1124 502306-2111 502306-2112 502306-2113 502306-2114
502306-2121 502306-2122 502306-2123 502306-2124
502306
TPA Latch
Before terminals can be extracted the TPA latch must be opened. Use the applicable extractor tool below:
For 27 Way and 48 Way Connectors see document ATS-638138200.
For 32 Way Connectors see document ATS-638139900.
For 53 Way Connectors see document ATS-638240100.
For 70 Way Connectors see document ATS-638241900.
For 120 Way Connectors see document ATS-638242000.
LOCKING
LATCHES
OPEN
(BOTH
SIDES)
TPA
SECONDARY
LOCK OPEN
TPA
SECONDARY
LOCKING
LATCHES
(BOTH SIDES)
TPA
SECONDARY
LOCK
SLOTS
SLOTS
EXTRACTOR
TOOL
Figure 2
Figure 1
EXTRACTOR
TOOL
Doc No: ATS-638240900
Revision: B
Release Date: 02-04-11
Revision Date: 02-21-12
UNCONTROLLED COPY
Page 1 of 2
Extractor Tool for CTX64 Receptacle Crimp Terminal
ORIENTATION
SLOTS
1. Insert the extractor tool into the (2) side
slots of the (TPA) secondary lock on
each sides until it stops. See Figure 1.
2. While keeping the extractor tool in this
position pull down on the (TPA)
WIRE
secondary lock. The locking latches
should be visible. See Figure 2.
3. Remove the extractor tool and check the
position of the TPA.
Figure 3
OPERATION:
When removing a damaged crimped wire
from the CMX connector follow the steps
below:
ORIENTATION GROVE
IN EXTRACTOR TOOL
CMX CONNECTOR
1. The extractor tool has an orientation groove on one side to match the orientation slot on the front of the connector
assembly.
2. Turn the extractor tool until the open part of the orientation groove is lined up with the vertical side of the slot.
3. Position the blade of the extraction tool into the orientation slot in the front face of the housing. See Figure 3.
4. Use the identifying markings on both the front and back of the connector to locate the opening used to extract the
crimped wire.
CRIMPED WIRE
AND TERMINAL
PUSH EXTRACTOR
TOOL INTO FRONT FACE
Figure 4
CMX HOUSING
5. Push extractor tool into the desired orientation slot until it clicks or comes to a stop. Do not force the extractor
tool any further or there can be damage to the housing. See Figure 4.
6. Gently push the wire forward towards the housing and then pull out of the CMX housing.
7. Molex does not offer repair parts for Extractor Tools due to the inexpensive nature of these tools.
http://www.molex.com
Doc No: ATS-638240900
Revision: B
Release Date: 02-04-11
Revision Date: 02-21-12
UNCONTROLLED COPY
Page 2 of 2
相关型号:
©2020 ICPDF网 联系我们和版权申明