62201-8611 [MOLEX]
Tool And Machinery, Insertion Tool,;
| 型号： | 62201-8611 |
| 厂家： | 
Molex |
| 描述： | Tool And Machinery, Insertion Tool, 工具和机器 连接器 连接器支架 |
| 文件： | 总4页 (文件大小：230K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
I-Trac™ Daughtercard and RAM Press-In Tool
I-Trac™ Daughtercard Module and RAM Installation
Application Tooling Specification
Press-In Tool
Order No. 62201-8611
FEATURES
ꢀ
ꢀ
ꢀ
Lip provided for positive alignment to connector assembly.
Tool provides uniform distribution of press force across entire pin array.
May be used as a stand-alone tool or mounted in an optional holder with other Molex press-in tools.
SCOPE
Products: I-Trac™ Daughtercard Signal Module Assembly, 76020 Series 6 Column Assemblies, and I-Trac™
RAM, 76011 Series 6 Column Assemblies. See Product List below for specific part numbers.
Product List
The following is a partial list of the product order numbers and their specifications this tool is designed to run.
Updates to this list are available on www.molex.com.
76020 Series Numbers
Guide Style Columns
Assembly Order Number
Open
6
76020-0006 76020-1006 76020-0906 76020-1906
76020-2006 76020-2106 76020-2206 76020-2306 76020-2406 76020-2506
76020-2606 76020-2706 76020-2806 76020-3006 76020-3106 76020-3206
76020-3306 76020-3406 76020-3506 76020-3606 76020-3706 76020-3806
76020-4006 76020-4106 76020-4206 76020-4306 76020-4406 76020-4506
76020-4606 76020-4706 76020-4806 76020-5006 76020-5106 76020-5206
76020-5306 76020-5406 76020-5506 76020-5606 76020-5706 76020-5806
76020-2056 76020-2156 76020-2256 76020-2356 76020-2456 76020-2556
76020-2656 76020-2756 76020-2856 76020-3056 76020-3156 76020-3256
76020-3356 76020-3456 76020-3556 76020-3656 76020-3756 76020-3856
76020-4056 76020-4156 76020-4256 76020-4356 76020-4456 76020-4556
76020-4656 76020-4756 76020-4856 76020-5056 76020-5156 76020-5256
76020-5356 76020-5456 76020-5556 76020-5656 76020-5756 76020-5856
Guide Left
6
Guide Right
6
6
6
Guide Left
(ESD)
Guide Right
(ESD)
76011 Series Numbers
Guide Style
Open
Left End Wall
Right End Wall
Dual End Wall
Columns
Assembly Order Number
6
6
6
6
76011-0603 76011-0605 76011-0606 76011-1603 76011-1605 76011-1606
76011-0613 76011-0615 76011-0616 76011-1613 76011-1615 76011-1616
76011-0623 76011-0625 76011-0626 76011-1623 76011-1625 76011-1626
76011-0633 76011-0635 76011-0636 76011-1633 76011-1635 76011-1636
76011-2623 76011-2625 76011-2626 76011-2633 76011-2635 76011-2636
76011-3623 76011-3625 76011-3626 76011-3633 76011-3635 76011-3636
76011-6623 76011-6625 76011-6626 76011-6633 76011-6635 76011-6636
76011-7623 76011-7625 76011-7626 76011-7633 76011-7635 76011-7636
76011-4623 76011-4625 76011-4626 76011-4633 76011-4635 76011-4636
76011-5623 76011-5625 76011-5626 76011-5633 76011-5635 76011-5636
76011-8623 76011-8625 76011-8626 76011-8633 76011-8635 76011-8636
76011-9623 76011-9625 76011-9626 76011-9633 76011-9635 76011-9636
Guide Left
6
6
Guide Right
Doc No: ATS-622018611
Revision: F
Release Date: 09-15-06
Revision Date: 02-18-09
UNCONTROLLED COPY
Page 1 of 4
I-Trac™ Daughtercard and RAM Press-In Tool
Tool Setup
Depending on the number of connectors to be installed and/or the press used, this tool can be used alone or with
a group of press-in tools, mounted in a 62201-95XX rail (ordered separately). See Figure 1.
WITH 62201-95XX
RAIL
ALONE
Figure 1
Tool Installation
The 62201-95XX rail is available in a variety of lengths to accommodate multiple press-in tools.
Rail Part Number Rail Overall Length
62201-9501
62201-9502
62201-9503
62201-9504
62201-9509
62201-9511
24mm (0.94 in)
72mm (2.83 in)
156mm (6.14 in)
216mm (8.50 in)
254mm (10.0 in)
305mm (12.0 in)
Reference: This Press-In Tool is 22.3mm (0.88 in.) long.
Printed Circuit Board (PCB) Support
The I-Trac™ connectors require up to 1.81kg (4 lbs) of force per pin to press into the PCB. To prevent excessive
PCB flexure and/or damage to the PCB, a support plate is strongly recommended directly beneath the connector
hole pattern.
Due to the custom nature of every application, Molex does not offer any PCB support plate. The customer must
furnish their own support plate.
When creating the PCB support plate, remember to allow clearance for the connector pins as they pass through
the PCB thickness.
Doc No: ATS-622018611
Revision: F
Release Date: 09-15-06
Revision Date: 02-18-09
UNCONTROLLED COPY
Page 2 of 4
I-Trac™ Daughtercard and RAM Press-In Tool
Press Equipment Recommendations
Many types of presses can be used to install I-Trac™ connectors, but to assure consistent connector installation
Molex recommends the following press criteria:
1. The capability to detect force variations as low as 4.5kg (10 lb) during the press-in cycle; excessive force
measurements should stop the press-in cycle.
2. The rate of pressing can be regulated as low as 0.13mm (0.005 in) per second.
3. Press stroke control to within 0.25mm (0.010 in).
4. Total press stroke must be at least 19mm (0.75 in).
5. For statistical purposes, automatic collection of force and distance data.
Tool Operation
1. Carefully insert, by hand, Daughtercard and / or RAM module(s) into the PCB hole pattern.
2. Place the application tool on top of the module with the back guide surface of the tool against the back of the
Daughtercard module. See Figure 2.
GUIDE SURFACE
Figure 2
3. Using the application tool and an appropriate press, seat the module until there is less than 0.10mm (.004 in)
clearance between the bottom of the plastic housing and the surface of the PCB. See Figure 3.
0.10
MAX
.004
Figure 3
(Daughtercard shown; same dimensions for RAM)
There should be no broken stand-offs along the perimeter of the part (an indication of over-pressing).
Doc No: ATS-622018611
Revision: F
Release Date: 09-15-06
Revision Date: 02-18-09
UNCONTROLLED COPY
Page 3 of 4
I-Trac™ Daughtercard and RAM Press-In Tool
CAUTION: To prevent injury, never operate any press without the guards in place. Refer to the press
manufacturer’s instruction manual.
CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and
tooling.
Contact Information
For more information on Molex application tooling please contact Molex at 1-800-786-6539.
Americas Headquarters
Lisle, Illinois 60532 U.S.A. Yamato, Kanagawa, Japan
1-800-78MOLEX
amerinfo@molex.com
Far East North Headquarters Far East South Headquarters European Headquarters Corporate Headquarters
Jurong, Singapore
65-6-268-6868
Munich, Germany
49-89-413092-0
eurinfo@molex.com
2222 Wellington Ct.
Lisle, IL 60532 U.S.A.
630-969-4550
81-462-65-2324
feninfo@molex.com
fesinfo@molex.com
Fax: 630-969-1352
Visit our Web site at http://www.molex.com
Doc No: ATS-622018611
Revision: F
Release Date: 09-15-06
Revision Date: 02-18-09
UNCONTROLLED COPY
Page 4 of 4
相关型号：
©2020 ICPDF网 联系我们和版权申明