IA2412KS-2W [MORNSUN]
Analog Circuit;型号: | IA2412KS-2W |
厂家: | MORNSUN SCIENCE& TECHNOLOGY LTD. |
描述: | Analog Circuit |
文件: | 总3页 (文件大小:295K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
IA_KS-2W & IA_S-2W Series
2W, FIXED INPUT, ISOLATED & REGULATED
DUAL OUTPUT DC-DC CONVERTER
RoHS
FEATURES
PRODUCT PROGRAM
SIP Package
1KVDC Isolation
Input
Output
Current (mA)
Switching
frequency
(KHz, Typ)
Part
Number
Efficiency
(%, Typ)
Voltage (VDC)
Voltage
(VDC)
Temperature Range: -40°C to +85°C
No Heat sink Required
Internal SMD Construction
No External Component Required
Industry Standard Pinout
RoHS Compliance
Nominal
Range
Max
±150
±200
±100
±83
Min
IA0505S-1W5
IA0505S-2W
±5
±5
±15
±20
±10
±9
69
70
62
64
65
70
63
65
68
70
63
67
69
100
55
5
4.75-5.25
IA0509KS-2W
IA0512KS-2W
IA0515KS-2W
IA1205S-1W5
IA1209KS-2W
IA1212KS-2W
IA1215KS-2W *
IA2405S-1W5
IA2409KS-2W
IA2412KS-2W
IA2415KS-2W
* Designing.
±9
67
±12
±15
±5
67
±67
±7
200
83
±150
±100
±83
±15
±10
±9
±9
91
12
24
11.4-12.6
22.8-25.2
±12
±15
±5
91
APPLICATIONS
The IA_KS-2W
&
IA_S-2W Series are
±67
±7
200
83
specially designed for applications where a
group of polar power supplies are isolated from
the input power supply in a distributed power
supply system on a circuit board.
±150
±100
±83
±15
±10
±9
±9
100
200
91
±12
±15
±67
±7
These products apply to:
1) Where the voltage of the input power supply
is fixed (voltage variation ≤±5%);
2) Where isolation is necessary between input
and output (isolation voltage ≤1000VDC);
3) Where the regulation of the output voltage
and the output ripple noise are demanded.
ISOLATION SPECIFICATION
Item
Test conditions
Min
Typ
Max
Units
VDC
MΩ
Isolation voltage
Isolation resistance
Tested for 1 minute and 1mA max
Test at 500VDC
1000
1000
OUTPUT SPECIFICATIONS
MODEL SELECTION
IA 2409 KS-2W
Item
Test Conditions
Min
0.2
Typ
Max
2
Units
W
Output power
Line regulation
Load regulation
Rated Power
Package Style
Output Voltage
For Vin change of ±5%
±0.25
±1
%
10% to 100% full load
Input Voltage
Product Series
Output voltage accuracy 100% full load
±3
Temperature drift
Output ripple*
Noise*
100% full load
0.03
30
%/°C
20MHz Bandwidth
20MHz Bandwidth
20
75
mVp-p
150
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui development
center, Science Ave., Guangzhou Science City,
Luogang district, Guangzhou,P.R.China.
Tel: 86-20-28203030
Fax:86-20-28203068
Http://www.mornsun-power.com
MORNSUN reserves the copyright
Specifications subject to change without notice.
IA_KS-2W & IA_S-2W
A/4-2010
Page 1 of 3
COMMON SPECIFICATIONS
EXTERNAL CAPACITOR TABLE (Table 1)
Item
Test conditions
Min
Typ
20
Max
95
Units
%
Vin
(VDC)
5
Cin
(uF)
4.7
Vout
(VDC)
±5
Cout
(uF)
4.7
Storage humidity
Operating temperature
Storage temperature
Temp. rise at full load
Lead temperature
Cooling
-40
-55
85
12
24
--
2.2
1
±9
2.2
1
125
30
°C
±12
±15
--
0.47
300
It’s not recommend to connect any external capacitor in the
application field with less than 0.5 watt output。
Free air convection
Plastic (UL94-V0)
Continuous
1
Case material
IAXX05S-2W/1W5
Others*
Short circuit protection
s
Input Over-voltage Protection Circuit
The simplest device for input over-voltage
protection is a linear voltage regulator with overheat
protection that is connected to the input end in series
(Figure 2).
MTBF
3500
K hours
g
Weight
5.2
*Supply voltage must be discontinued at the end of short circuit duration.
TYPICAL CHARACTERISTICS
+Vout
REG
Vin
Temperature Derating Graph
0V
DC DC
GND
-Vout
(Figure 2)
When the environment temperature is higher
than 71°C, the product output power should be
less then 60% of the rated power.
No parallel connection or plug and play.
Operating Temp.( C )
APPLICATION NOTE
Requirement on output load
Use dual output simultaneously, forbid opening
output pin(0V) to use as single output.
To ensure this module can operate efficiently and reliably, a minimum load is specified for
this kind of DC/DC converter in addition to a maximum load (namely full load). During
operation, make sure the specified range of input voltage is not exceeded, the minimum
output load could not be less than 10% of the full load. If the actual output power is very
small, please connect a resistor with proper resistance at the output end in parallel to
increase the load, or use our company’s products with a lower rated output power (IA_KS
–1W/IA_S-1W series).
Filtering
To get an extreme low ripple, an “LC” filtering network may be connected to the input and
output ends of the DC/DC converter, which may produce a more significant filtering effect. It
should also be noted that the inductance and the frequency of the “LC” filtering network should
be staggered with the DC/DC frequency to avoid mutual interference (see figure 1).
L
L
+Vo
Vin
Cout
0V
Cin
DC
DC
L
Cout
GND
-Vo
(Figure 1)
In some circuits which are sensitive to noise and ripple, a filtering capacitor may be added to
the DC/DC output end and input end to reduce the noise and ripple. However, the capacitance
of the output filter capacitor must be proper. If the capacitance is too big, a startup problem
might arise. For every channel of output, provided the safe and reliable operation is ensured,
the greatest capacitance of its filter capacitor sees the EXTERNAL CAPACITOR TABLE (see
Table 1).
MORNSUN reserves the copyright
Specifications subject to change without notice.
IA_KS-2W & IA_S-2W
A/4-2010
Page 2 of 3
OUTLINE DIMENSIONS & PIN CONNECTIONS
RECOMMENDED FOOTPRINT
MECHANICAL DIMENSIONS
27.50[1.083]
Ф
1.00[Ф0.039]
22.86[0.900]
17.78 [0.700]
1
7
9 10
2
0.90 [0.035]
17.78 [0.700]
2
1
7
9 10
22.86[0.900]
27.50[1.083]
2.54[0.100]
TUBE OUTLINE DIMENSIONS
12.00 [0.472]
0.50[0.020]
2.54[0.100]
0.50[0.020]
Note:
Unit:mm[inch]
Pin tolerances: 0.10mm[ 0.004inch]
0.60 [0.024]
General tolerances: 0.25mm[ 0.010inch]
5.70 [0.224]
Note:
FOOTPRINT DETAILS
Unit :mm[inch]
General tolerances: 0.50mm [ 0.020inch]
L=530mm[20.866inch] Devices per tube quantity: 18pcs
L=220mm[8.661inch] Devices per tube quantity: 7pcs
Short tube inner packaging dimensions: L*W*H=255*170*80mm
Short tube outer packaging dimensions: L*W*H=375*280*270mm
Long tube inner packaging dimensions: L*W*H=580*200*100mm
Long tube outer packaging dimensions(with two inner packaging boxes):
Pin
1
Function
Vin
2
GND
7
+Vo
9
-Vo
0V
10
L*W*H= 600*215*220mm
Long tube outer packaging dimensions(withl three inner packaging boxes):
L*W*H=600*215*325mm
Note:
1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the life
of product.
2. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
3. Only typical models listed, other models may be different, please contact our technical person for more details.
4. In this datasheet, all the test methods of indications are based on corporate standards.
MORNSUN reserves the copyright
Specifications subject to change without notice.
IA_KS-2W & IA_S-2W
A/4-2010
Page 3 of 3
相关型号:
©2020 ICPDF网 联系我们和版权申明