M1MA151AT1 [MOTOROLA]
SC-59 PACKAGE SINGLE SILICON SWITCHING DIODES 40/80 V-100 mA SURFACE MOUNT; SC- 59封装单硅开关二极管40/80 V -100麻面贴装型号: | M1MA151AT1 |
厂家: | MOTOROLA |
描述: | SC-59 PACKAGE SINGLE SILICON SWITCHING DIODES 40/80 V-100 mA SURFACE MOUNT |
文件: | 总6页 (文件大小:85K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Order this document
by M1MA151AT1/D
SEMICONDUCTOR TECHNICAL DATA
These Silicon Epitaxial Planar Diodes are designed for use in ultra high speed
switching applications. These devices are housed in the SC–59 package which is
designed for low power surface mount applications.
Motorola Preferred Devices
•
•
•
Fast t , < 3.0 ns
rr
Low C , < 2.0 pF
D
Available in 8 mm Tape and Reel
Use M1MA151/2AT1 to order the 7 inch/3000 unit reel.
Use M1MA151/2AT3 to order the 13 inch/10,000 unit reel.
SC–59 PACKAGE
SINGLE SILICON
SWITCHING DIODES
40/80 V–100 mA
ANODE
3
SURFACE MOUNT
3
2
1
2
1
CATHODE NO CONNECTION
MAXIMUM RATINGS (T = 25°C)
A
CASE 318D–03, STYLE 4
SC–59
Rating
Symbol
Value
40
Unit
Reverse Voltage
M1MA151AT1
V
R
Vdc
M1MA152AT1
M1MA151AT1
M1MA152AT1
80
Peak Reverse Voltage
V
RM
40
Vdc
80
Forward Current
I
100
225
500
mAdc
mAdc
mAdc
F
Peak Forward Current
Peak Forward Surge Current
I
FM
(1)
I
FSM
THERMAL CHARACTERISTICS
Rating
Symbol
Max
200
Unit
mW
°C
Power Dissipation
P
D
Junction Temperature
Storage Temperature
T
J
150
T
stg
–55 to +150
°C
ELECTRICAL CHARACTERISTICS (T = 25°C)
A
Characteristic
Symbol
Condition
Min
Max
0.1
0.1
1.2
—
Unit
Reverse Voltage Leakage Current
M1MA151AT1
M1MA152AT1
I
R
V
= 35 V
= 75 V
—
—
—
40
80
—
—
µAdc
R
R
V
Forward Voltage
V
F
I
= 100 mA
Vdc
Vdc
F
Reverse Breakdown Voltage
M1MA151AT1
M1MA152AT1
V
R
I
= 100 µA
R
—
Diode Capacitance
C
V
= 0, f = 1.0 MHz
2.0
3.0
pF
ns
D
R
(2)
t
rr
Reverse Recovery Time
I = 10 mA, V = 6.0 V,
F R
R
= 100 Ω, I = 0.1 I
L
rr
R
1. t = 1 SEC
2. t Test Circuit
rr
Thermal Clad is a trademark of the Bergquist Company
Preferred devices are Motorola recommended choices for future use and best overall value.
REV 3
Motorola, Inc. 1996
RECOVERY TIME EQUIVALENT TEST CIRCUIT
INPUT PULSE
OUTPUT PULSE
t
r
t
t
p
rr
I
F
t
t
10%
R
L
I
= 0.1 I
R
A
rr
90%
I
V
R
= 10 mA
F
= 6 V
= 100 Ω
R
V
R
L
t
= 2 µs
p
t = 0.35 ns
r
DEVICE MARKING
Marking Symbol
Type No.
151A
152A
MAX
Symbol
MA
MB
The “X” represents a smaller alpha digit Date Code. The Date Code
indicates the actual month in which the part was manufactured.
2
Motorola Small–Signal Transistors, FETs and Diodes Device Data
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
0.037
0.95
0.037
0.95
0.098–0.118
2.5–3.0
0.094
2.4
0.039
1.0
0.031
0.8
inches
mm
SC–59 POWER DISSIPATION
The power dissipation of the SC–59 is a function of the pad
size. This can vary from the minimum pad size for soldering
to the pad size given for maximum power dissipation. Power
dissipation for a surface mount device is determined by
the equation for an ambient temperature T of 25°C, one can
calculate the power dissipation of the device which in this
case is 200 milliwatts.
A
150°C – 25°C
T
R
, the maximum rated junction temperature of the die,
, the thermal resistance from the device junction to
J(max)
θJA
P
=
= 200 milliwatts
D
625°C/W
ambient; and the operating temperature, T . Using the
values provided on the data sheet, P can be calculated as
D
follows:
A
The 625°C/W assumes the use of the recommended
footprint on a glass epoxy printed circuit board to achieve a
power dissipation of 200 milliwatts. Another alternative would
be to use a ceramic substrate or an aluminum core board
such as Thermal Clad . Using a board material such as
Thermal Clad, a power dissipation of 400 milliwatts can be
achieved using the same footprint.
T
– T
A
J(max)
P
=
D
R
θJA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
•
•
•
The soldering temperature and time should not exceed
260°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient should be 5°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
•
•
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100°C or less.*
•
Mechanical stress or shock should not be applied during
cooling
•
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference should be a maximum of 10°C.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
Motorola Small–Signal Transistors, FETs and Diodes Device Data
3
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the SC–59 package should be
the same as the pad size on the printed circuit board, i.e., a
1:1 registration.
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a
figure for belt speed. Taken together, these control settings
make up a heating “profile” for that particular circuit board.
On machines controlled by a computer, the computer
remembers these profiles from one operating session to the
next. Figure 1 shows a typical heating profile for use when
soldering a surface mount device to a printed circuit board.
This profile will vary among soldering systems but it is a good
starting point. Factors that can affect the profile include the
type of soldering system in use, density and types of
components on the board, type of solder used, and the type
of board or substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density board.
The Vitronics SMD310 convection/infrared reflow soldering
system was used to generate this profile. The type of solder
used was 62/36/2 Tin Lead Silver with a melting point
between 177–189°C. When this type of furnace is used for
solder reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK” ZONES 2 & 5
“RAMP”
STEP 3
HEATING
STEP 4
HEATING
ZONES 3 & 6 ZONES 4 & 7
“SOAK” “SPIKE”
STEP 5
HEATING
STEP 6
VENT COOLING
STEP 7
205
PEAK AT
SOLDER JOINT
° TO 219°C
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
170°C
200
°C
160°C
150°C
150°C
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
140°C
100°C
MASS OF ASSEMBLY)
100°C
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
50°C
T
TIME (3 TO 7 MINUTES TOTAL)
MAX
Figure 1. Typical Solder Heating Profile
4
Motorola Small–Signal Transistors, FETs and Diodes Device Data
PACKAGE DIMENSIONS
A
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
L
MILLIMETERS
INCHES
MIN MAX
3
DIM
A
B
C
D
G
H
J
K
L
MIN
2.70
1.30
1.00
0.35
1.70
0.013
0.10
0.20
1.25
2.50
MAX
S
B
3.10 0.1063 0.1220
1.70 0.0512 0.0669
1.30 0.0394 0.0511
0.50 0.0138 0.0196
2.10 0.0670 0.0826
0.100 0.0005 0.0040
0.26 0.0040 0.0102
0.60 0.0079 0.0236
1.65 0.0493 0.0649
3.00 0.0985 0.1181
2
1
D
G
S
J
C
STYLE 4:
PIN 1. N.C.
2. CATHODE
3. ANODE
K
H
CASE 318D–03
ISSUE E
SC–59
Motorola Small–Signal Transistors, FETs and Diodes Device Data
5
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
M1MA151AT1/D
◊
相关型号:
©2020 ICPDF网 联系我们和版权申明