MC10198L [MOTOROLA]
Monostable Multivibrator; 单稳态多谐振荡器
| 型号： | MC10198L |
| 厂家： | 
MOTOROLA |
| 描述： | Monostable Multivibrator |
| 文件： | 总10页 (文件大小：155K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SEMICONDUCTOR TECHNICAL DATA
The MC10198 is a retriggerable monostable multivibrator. Two enable inputs
permit triggering on any combination of positive or negative edges as shown in
the accompanying table. The trigger input is buffered by Schmitt triggers
making it insensitive to input rise and fall times.
The pulse width is controlled by an external capacitor and resistor. The
resistor sets a current which is the linear discharge rate of the capacitor. Also,
the pulse width can be controlled by an external current source or voltage (see
applications information).
For high–speed response with minimum delay, a hi–speed input is also
provided. This input bypasses the internal Schmitt triggers and the output
responds within 2 nanoseconds typically.
Output logic and threshold levels are standard MECL 10,000. Test
conditions are per Table 2. Each “Precondition” referred to in Table 2 is per the
sequence of Table 1.
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
P
= 415 mW typ/pkg (No Load)
= 4.0 ns typ Trigger Inpt to Q
2.0 ns typ Hi–Speed Input to Q
D
t
pd
DIP
PIN ASSIGNMENT
1
10 ns typ
Min Timing Pulse Width
Max Timing Pulse Width
Min Trigger Pulse Width
Min Hi–Speed
Trigger Pulse Width
Enable Setup Time
Enable Hold Time
PW
PW
PW
PW
Qmin
Qmax
T
2
>10 ms typ
2.0 ns typ
3.0 ns typ
V
V
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
CC1
CC2
HS
HIGH–SPEED
INPUT
Q
t
t
1.0 ns typ
1.0 ns typ
set
hold
Q
N/C
C
E
TRIGGER INPUT
N/C
1
EXT
C
= 0 (Pin 4 open), R
= 0
Ext
(Pin 6 to V
Ext
)
EE
= 10 µF, R
POS
2
C
Ext
= 2.7 kΩ
Ext
R
N/C
EXT
EXT.PULSE
WIDTH CONTROL
E
NEG
V
N/C
EE
LOGIC DIAGRAM
V
V
CC
EE
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
6
4
R
C
EXT
EXT
E pos
Q
5
7
3
EXTERNAL PULSE
WIDTH CONTROL
TRUTH TABLE
V
V
V
= PIN 1
= PIN 16
= PIN 8
CC1
CC2
EE
INPUT
OUTPUT
E
10
13
NEG
E
Pos
E
Neg
TRIGGER
INPUT
L
L
H
H
L
H
L
Triggers on both positive & negative input slopes
Triggers on positive input slope
Triggers on negative input slope
Trigger is disabled
Q
2
HI–SPEED
INPUT
15
H
3/93
Motorola, Inc. 1996
REV 5
MC10198
TABLE 1 — PRECONDITION SEQUENCE
1. At t = 0 a.) Apply V
b.) Apply V
to Pin 5 and 10.
IHmax
to Pin 15.
ILmin
c.) Ground Pin 4.
10 ns a.) Open Pin 1.
b.) Apply –3.0 Vdc to Pin 4.
10 ns
10 ns
2. At t
0(Gnd)
–1.0
Hold these conditions for
10 ns.
3. Return Pin 4 to Ground and perform test as
indicated in Table 2.
–2.0
–3.0
Pin 1
open
–4.0
–5.0
0
10
20
30
t(ns)
TABLE 2 — CONDITIONS FOR TESTING OUTPUT LEVELS
(See Table 1 for Precondition Sequence)
V
IH max
V
IHA max
V
ILA max
V
P1
V
IL min
P3
V
IL min
P2
IL min
Pins 1, 16 = V
Pins 6, 8 = V
Outputs loaded 50 Ω to –2.0 Vdc
= Ground
= –5.2 Vdc
CC
EE
Pin Conditions
Pin Conditions
10
Test
P.U.T.
5
10
13
15
Test
P.U.T.
5
13
15
Precondition
Precondition
V
V
2
3
V
V
V
V
2
3
V
V
P1
P1
OH
OH
IL min
P1
OHA
OHA
IHA min
ILA max
Precondition
Precondition
V
OL
V
OL
3
2
V
OLA
V
OLA
3
2
V
ILA max
IL min
P1
V
IHA min
Precondition
Precondition
V
OHA
V
OHA
2
3
V
V
V
OLA
V
OLA
2
3
V
V
ILA max
IHA min
IL min
IL min
Precondition
Precondition
V
OHA
V
OHA
2
3
V
V
OLA
V
OLA
3
2
P2
P3
IL min
P3
Precondition
Precondition
V
OHA
V
OHA
2
3
P2
P3
V
OLA
V
OLA
3
2
V
V
P2
P3
IH max
IH max
Precondition
Precondition
V
OHA
V
OHA
2
3
V
V
P2
P3
V
OLA
V
OLA
3
2
V
V
V
V
P1
P1
IH max
IH max
IHA min
ILA max
IH max
IH max
Precondition
Precondition
V
OHA
V
OHA
2
3
V
V
P1
P1
V
OLA
V
OLA
3
2
V
V
V
P1
P1
IH max
IH max
IH max
IH max
IHA min
V
ILA max
3–173
MOTOROLA
MC10198
ELECTRICAL CHARACTERISTICS
Test Limits
+25°C
Typ
Pin
Under
Test
–30°C
+85°C
Characteristic
Power Supply Drain Current
Input Current
Symbol
Unit
mAdc
µAdc
Min
Max
Min
Max
Min
Max
I
E
8
110
80
100
110
I
5, 10
13
15
415
350
560
260
220
350
260
220
350
inH
I
5
0.5
0.5
0.3
µAdc
inL
Output Voltage
Logic 1
V
OH
2
3
–1.060
–1.060
–0.890
–0.890
–0.960
–0.960
–0.810
–0.810
–0.890
–0.890
–0.700
–0.700
Vdc
Output Voltage
Logic 0
Logic 1
Logic 0
V
2
3
–1.890
–1.890
–1.675
–1.675
–1.850
–1.850
–1.650
–1.650
–1.825
–1.825
–1.615
–1.615
Vdc
Vdc
Vdc
OL
Threshold Voltage
Threshold Voltage
V
OHA
2
3
–1.080
–1.080
–0.980
–0.980
–0.910
–0.910
V
OLA
2
3
–1.655
–1.655
–1.630
–1.630
–1.595
–1.595
Switching Times (50Ω Load)
Trigger Input
t
t
3
3
2.5
2.5
6.5
6.5
2.5
2.5
4.0
4.0
5.5
5.5
2.5
2.5
6.5
6.5
ns
T+Q+
T–Q+
High Speed Trigger Input
t
3
3
3
3
3
3
3
3
3
1.5
3.2
1.5
2.0
10.0
>10
2.0
2.8
1.5
3.2
ns
ns
ms
ns
ns
ns
ns
ns
ns
HS+Q+
Minimum Timing Pulse Width
PW
Qmin
Qmax
T
Maximum Timing Pulse Width PW
Min Trigger Pulse Width
PW
Min Hi–Spd Trig Pulse Width
PW
HS
3.0
Rise Time
Fall Time
(20 to 80%)
(20 to 80%)
1.5
1.5
4.0
4.0
1.5
1.5
3.5
3.5
1.5
1.5
4.0
4.0
Enable Setup Time
Enable Hold Time
t
(E)
1.0
1.0
setup
(E)
t
hold
1. The monostable is in the timing mode at the time of this test.
2. C
3. C
= 0 (Pin 4 Open); R
= 0 (Pin 6 tied to V ).
EXT
EXT
EXT
= 2.7k (Pin 6).
EE
= 10µF (Pin); R
EXT
V
V
IHmax
4.
ILmin
P1
MOTOROLA
3–174
MC10198
ELECTRICAL CHARACTERISTICS (continued)
TEST VOLTAGE VALUES (Volts)
@ Test Temperature
V
V
ILmin
V
V
V
EE
IHmax
IHAmin
ILAmax
–30°C
+25°C
+85°C
–0.890
–0.810
–0.700
–1.890
–1.850
–1.825
–1.205
–1.105
–1.035
–1.500
–1.475
–1.440
–5.2
–5.2
–5.2
Pin
Under
Test
TEST VOLTAGE APPLIED TO PINS LISTED BELOW
(V
CC
)
Characteristic
Power Supply Drain Current
Input Current
Symbol
Gnd
V
V
ILmin
V
V
V
EE
IHmax
IHAmin
ILAmax
I
E
8
6, 8
1, 4, 16
I
5, 10
13
15
5,10
13
15
6, 8
6, 8
6, 8
1, 4, 16
1, 4, 16
1, 4, 16
inH
I
5
5
6, 8
1, 4, 16
inL
Output Voltage
Logic 1
Logic 0
V
2
3
13
6, 8
6, 8
1, 4, 16
1, 4, 16
OH
13 (4.)
13 (4.)
Output Voltage
V
2
3
6, 8
6, 8
1, 4, 16
1, 4, 16
OL
13
Threshold Voltage
Threshold Voltage
Logic 1
V
2
3
15
15
6, 8
6, 8
1, 16, 4
1, 16, 4
OHA
15
15
Logic 0
V
2
3
6, 8
6, 8
1, 16, 4
1, 16, 4
OLA
Switching Times
Trigger Input
(50Ω Load)
+1.11V
Pulse In
Pulse Out
–3.2 V
+2.0 V
t
t
3
3
10
5
13
13
3
3
6, 8
6, 8
1, 16, 4
1, 16, 4
T+Q+
T–Q+
High Speed Trigger Input
t
3
3
3
3
3
3
3
3
3
15
3
Note 2.
Note 3.
3
6, 8
6, 8
6, 8
6, 8
6, 8
6, 8
6, 8
6, 8
6, 8
1, 16, 4
1, 16, 4
1, 16, 4
1, 16, 4
1, 16, 4
1, 16, 4
1, 16, 4
1, 16, 4
1, 16, 4
HS+Q+
Minimum Timing Pulse Width
Maximum Timing Pulse Width
Minimum Trigger Pulse Width
Minimum Hi–Spd Trigger Pulse Width
PW
Qmin
PW
Qmax
PW
13
15
T
PW
3
HS
Rise Time
(20 to 80%)
(20 to 80%)
Fall Time
Enable Setup Time
Enable Hold Time
t
(E)
5
5
3
3
setup
(E)
t
hold
1. The monostable is in the timing mode at the time of this test.
2. C
3. C
= 0 (Pin 4 Open); R
= 0 (Pin 6 tied to V ).
EXT
EXT
EXT
= 2.7k (Pin 6).
EE
= 10µF (Pin); R
EXT
V
V
IHmax
4.
ILmin
P1
Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been
established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained.
Outputs are terminated through a 50–ohm resistor to –2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the
same manner.
3–175
MOTOROLA
MC10198
SWITCHING TIME TEST CIRCUIT AND WAVEFORMS @ 25°C
V
= V = +2.0 Vdc
CC2
V
CC1
V
out
in
25
µF
0.1 µF
Coax
Input
Coax
5
7
E
Pos
3
External Pulse
Width Control
Q
TP
in
10
E
Neg
TP
Pulse Generator
+1.11 V
0.1
out
13
15
Trigger Input
µF
Hi–Speed Input
Input Pulse
t+ = t– = 2.0
± 0.2 ns
(20 to 80%)
6
4
2
R
C
Q
Ext
Ext
50–ohmtermination to ground located
in each scope channel input.
Unused outputs are tied to a
50–ohm resistor to ground.
0.1 µF
Allinputandoutputcablestothescope
are equal lengths of 50–ohm coaxial
cable. Wire length should be < 1/4 inch
V
= –3.2 Vdc
EE
from TP to input pin and TP
to
in
out
output pin.
50%
setup (E)
E
Pos
t
Trigger Input
50%
PW
T
t
Hold(E)
t
t
T+Q+
T–Q+
50%
Q
50%
PW
Q
High–Speed
Trigger Input
PW
HS
t
HS+Q+
Q
PW
Q
MOTOROLA
3–176
MC10198
APPLICATIONS INFORMATION
Figure 2 shows typical curves for pulse width
Circuit Operation:
versus C
and R (total resistance includes R ).
Ext
Ext Int
1.PULSE WIDTH TIMING — The pulse width is deter-
mined by the external resistor and capacitor. The
MC10198 also has an internal resistor (nominally 284
Any low leakage capacitor can be used and R
vary from 0 to 16 k–ohms.
can
Ext
ohms) that can be used in series with R . Pin 7, the
external pulse width control, is a constant voltage node
(–3.60 V nominally). A resistance connected in series
Ext
2.TRIGGERING —The E
pos
and E
inputs control the
Neg
triggerinput. TheMC10198canbeprogrammedtotrig-
ger on the positive edge, negative edge, or both. Also,
the trigger input can be totally disabled. The truth table
is shown on the first page of the data sheet.
from this node to V
This current determines the discharge rate of the ca-
pacitor:
sets a constant timing current I .
EE
T
The device is totally retriggerable. However, as
duty cycle approaches 100%, pulse width jitter can
occur due to the recovery time of the circuit. Recovery
∆V
∆T
I
T
= C
Ext
time is basically dependent on capacitance C
.
Ext
Figure 3 shows typical recovery time versus capaci-
where
Then:
∆T = pulse width
∆V = 1.9 V change in capacitor voltage
tance at I = 5 mA.
T
FIGURE 2 – TIMING PULSE WIDTH versus C
and R
Ext
Ext
1.9 V
∆T = C
Ext
100
I
T
If R
Ext
+ R are in series to V
:
Int
EE
Ext
10
I
T
T
= [(–3.60 V) – (–5.2 V)] ÷ [R
+ 284 Ω]
10 kΩ
I
= 1.6 V/(R
+ 284)
Ext
3 k
Ω
The timing equation becomes:
1
500
Ω
∆T = [(C )(1.9 V)] ÷ [1.6 V/(R
+ 284)]
Ext
Ext
∆T = C
(R + 284) 1.19
Ext Ext
100
10
where ∆T = Sec
R
= 0
NOTE: TOTAL RESISTANCE
= R + R
Ext
R
C
= Ohms
= Farads
Ext
Int
Ext
Ext
10 pF
100 pF
1000 pF
0.01
µF
0.1 µF
C
– TIMING CAPACITANCE
Ext
FIGURE 1 —
FIGURE 3 — RECOVERY TIME versus C
@ I = 5 mA
T
Ext
10
1
µ
s
4
C
Ext
µs
MC10198
7
100 ns
–3.60 V External
Pulse Width Control
R
V
284
6
Ω
Int
10 ns
1 ns
R
Ext
10 pF
100 pF
1000 pF
0.01
µF
0.1 µF
= –5.2 V
EE
C
– TIMING CAPACITANCE
Ext
3–177
MOTOROLA
MC10198
3.HI–SPEED INPUT — This input is used for stretching
very narrow pulses with minimum delay between the
output pulse and the trigger pulse. The trigger input
should be disabled when using the high–speed input.
The MC10198 triggers on the rising edge, using this in-
put, and input pulse width should narrow, typically less
than 10 nanoseconds.
FIGURE 5 — PULSE WIDTH versus I @ C
Ext
= 13 pF
T
1000
100
USAGE RULES:
1.Capacitor lead lengths should be kept very short to mini-
mize ringing due to fast recovery rise times.
2.The E inputs should not be tied to ground to establish a
high logic level. A resistor divider or diode can be used
to establish a –0.7 to –0.9 voltage level.
3.Foroptimumtemperature stability; 0.5 mA is the best tim-
ing current I . The device is designed to have a constant
10
T
voltage at the EXTERNAL PULSE WIDTH CONTROL
over temperature at this current value.
0.01 mA
0.1 mA
1 mA
– TIMING CURRENT
10 mA
I
T
4.Pulse Width modulation can be attained with the EXTER-
NAL PULSE WIDTH CONTROL. Thetimingcurrentcan
be altered to vary the pulse width. Two schemes are:
a. The internal resistor is not used. A dependent cur-
rent source is used to set the timing current as
shown in Figure 4. A graph of pulse width versus
b. A control voltage can also be used to vary the
pulse width using an additional resistor (Figure 6).
The current (I + I ) is set by the voltage drop
T
C
acrossR +R .ThecontrolcurrentICmodifies
Int Ext
I
and alters the pulse width. Current I should
T
C
timing current (C
= 13 pF) is shown in Figure 5.
never force I to zero. R typically 1 kΩ.
Ext
T
C
FIGURE 6 —
FIGURE 4 —
4
C
Ext
4
C
Ext
I
C
I
T
7
Control
Voltage
MC10198
R
–3.6
V
C
284
7
6
I
R
I
+ I
C
Ext
–5.2 V
T
MOTOROLA
3–178
MC10198
5.The MC10198 can be made non–retriggerable. The Q
output is fed back to disable the trigger input during the
triggered state (Logic Diagram). Figure 7 shows a posi-
tive triggered configuration; a similar configuration can
be made for negative triggering.
FIGURE 7 —
V
V
CC
EE
R
Ext
C
Ext
6
4
Q
E
Pos
External Pulse
Width Control
–0.9 V
E
Neg
Trigger
Input
Hi–Speed
Input
Q
3–179
MOTOROLA
MC10198
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 775–02
ISSUE C
M
S
S
0.007 (0.180)
T
L–M
N
B
Y BRK
–M–
–N–
M
S
S
0.007 (0.180)
T
L–M
N
U
D
D
–L–
Z
W
20
1
S
S
S
0.010 (0.250)
T
L–M
N
G1
X
V
VIEW D–D
M
M
S
S
S
S
A
R
0.007 (0.180)
0.007 (0.180)
T
L–M
L–M
N
N
Z
T
M
S
S
0.007 (0.180)
T
L–M
N
H
C
K1
E
K
0.004 (0.100)
–T– SEATING
G
J
PLANE
M
S
S
0.007 (0.180)
T
L–M
N
F
VIEW S
G1
VIEW S
S
S
S
0.010 (0.250)
T
L–M
N
NOTES:
1. DATUMS –L–, –M–, AND –N– DETERMINED
INCHES
MILLIMETERS
DIM
MIN
MAX
0.395
0.395
0.180
0.110
0.019
MIN
9.78
9.78
4.20
2.29
0.33
MAX
10.03
10.03
4.57
2.79
0.48
WHERE TOP OF LEAD SHOULDER EXITS PLASTIC
BODY AT MOLD PARTING LINE.
A
B
C
E
0.385
0.385
0.165
0.090
0.013
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T–, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037 (0.940).
THE DAMBAR INTRUSION(S) SHALL NOT CAUSE
THE H DIMENSION TO BE SMALLER THAN 0.025
(0.635).
F
G
H
J
K
R
U
V
W
X
Y
0.050 BSC
1.27 BSC
0.026
0.020
0.025
0.350
0.350
0.042
0.042
0.042
–––
0.032
–––
–––
0.356
0.356
0.048
0.048
0.056
0.020
10
0.66
0.51
0.64
8.89
8.89
1.07
1.07
1.07
–––
2
0.81
–––
–––
9.04
9.04
1.21
1.21
1.42
0.50
10
Z
G1
K1
2
0.310
0.040
0.330
–––
7.88
1.02
8.38
–––
MOTOROLA
3–180
MC10198
OUTLINE DIMENSIONS
L SUFFIX
CERAMIC DIP PACKAGE
CASE 620–10
–A–
NOTES:
ISSUE V
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION F MAY NARROW TO 0.76 (0.030)
WHERE THE LEAD ENTERS THE CERAMIC
BODY.
16
1
9
8
–B–
C
L
INCHES
MILLIMETERS
DIM
A
B
C
D
MIN
MAX
0.785
0.295
0.200
0.020
MIN
19.05
6.10
–––
MAX
19.93
7.49
5.08
0.50
0.750
0.240
–––
–T–
SEATING
PLANE
0.015
0.39
K
N
E
0.050 BSC
1.27 BSC
F
0.055
0.065
1.40
1.65
G
H
K
L
M
N
0.100 BSC
2.54 BSC
M
E
0.008
0.125
0.015
0.170
0.21
3.18
0.38
4.31
F
J
16 PL
0.25 (0.010)
G
0.300 BSC
7.62 BSC
M
S
T
B
0
15
0
15
D 16 PL
0.25 (0.010)
0.020
0.040
0.51
1.01
M
S
T
A
P SUFFIX
PLASTIC DIP PACKAGE
CASE 648–08
ISSUE R
NOTES:
–A–
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
16
1
9
8
B
S
INCHES
MILLIMETERS
DIM
A
B
C
D
F
MIN
MAX
0.770
0.270
0.175
0.021
0.70
MIN
18.80
6.35
3.69
0.39
1.02
MAX
19.55
6.85
4.44
0.53
1.77
F
0.740
0.250
0.145
0.015
0.040
C
L
SEATING
–T–
G
H
J
K
L
0.100 BSC
0.050 BSC
2.54 BSC
1.27 BSC
PLANE
K
M
0.008
0.015
0.130
0.305
10
0.21
0.38
3.30
7.74
10
H
J
0.110
0.295
0
2.80
7.50
0
G
D 16 PL
0.25 (0.010)
M
S
0.020
0.040
0.51
1.01
M
M
T
A
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax : RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC10198/D
◊
相关型号：
©2020 ICPDF网 联系我们和版权申明