MC10H334LS [MOTOROLA]
Registered Bus Transceiver, 1-Func, 4-Bit, True Output, ECL10K, CDIP20;
| 型号： | MC10H334LS |
| 厂家： | 
MOTOROLA |
| 描述： | Registered Bus Transceiver, 1-Func, 4-Bit, True Output, ECL10K, CDIP20 总线驱动器 总线收发器 锁存器 逻辑集成电路 |
| 文件： | 总4页 (文件大小：109K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SEMICONDUCTOR TECHNICAL DATA
The MC10H334 is a Quad Bus Driver/Receiver with transmit and receiver
latches. When disabled, (OE = high) the bus outputs will fall to –2.0 V. Data to
be transmitted or received is passed through its respective latch when the
respective latch enable (DLE and RLE) is at a low level. Information is latched
on the positive transition of DLE and RLE. The parameters specified are with
25 Ω loading on the bus drivers and 50 Ω loads on the receivers.
L SUFFIX
CERAMIC PACKAGE
CASE 732–03
P SUFFIX
PLASTIC PACKAGE
CASE 738–03
•
•
Propagation Delay, 1.6 ns Typical Data–to–Output
Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
Voltage Compensated
MECL 10K–Compatible
FN SUFFIX
PLCC
CASE 775–02
•
•
DIP & PLCC
PIN ASSIGNMENT
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Vdc
Vdc
mA
Power Supply (V
= 0)
V
EE
–8.0 to 0
CC
V
V
CC03
1
2
20
19
18
17
16
15
14
13
12
11
CC
Input Voltage (V
= 0)
V
I
0 to V
50
CC
EE
BUS1
BUS0
VCC02
D1
BUS2
BUS3
Output Current— Continuous
— Surge
I
out
100
3
Operating Temperature Range
T
A
0 to +75
°C
OE
D2
4
Storage Temperature Range— Plastic
— Ceramic
T
stg
–55 to +150
–55 to +165
°C
°C
5
D0
D3
6
ELECTRICAL CHARACTERISTICS (V
0°
= –5.2 V ±5%) (See Note)
EE
25°
75°
DLE
R0
RLE
R3
7
Characteristic
Symbol Min
Max
Min
Max
Min
Max
Unit
8
Power Supply Current
I
E
—
161
—
161
—
161
mA
R1
R2
9
Input Current High
Pins 5,6,15,16
Pins 7,14
I
µA
inH
—
—
—
397
460
520
—
—
—
273
297
357
—
—
—
273
297
357
V
V
10
EE
CC02
Pin 17
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
I
0.5
—
0.5
—
0.3
—
µA
inL
V
–1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc
–1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc
–1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc
–1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc
OH
V
OL
NOTE:
V
IH
Each MECL 10H series circuit has been designed
tomeetthedcspecificationsshowninthetesttable,
afterthermalequilibriumhasbeenestablished. The
circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than
500 Ifpm is maintained. Receiver outputs are
terminated through a 50–ohm resistor to –2.0 volts
dc. Bus outputs are terminated through a 25–ohm
resistor to –2.0 volts dc.
V
IL
AC PARAMETERS
Propagation Delay
Data–to–Bus Output
DLE–to–Bus Output
OE–to–Bus Output
Bus–to–R0
RLE–to–R0
Data–to–Receiver
R0
t
ns
pd
0.5
1.0
0.5
0.5
0.5
1.0
2.5
2.7
2.5
1.9
2.1
3.8
0.5
1.0
0.5
0.5
0.5
1.0
2.5
2.7
2.5
1.9
2.1
3.8
0.5
1.0
0.5
0.5
0.5
1.0
2.5
2.7
2.5
1.9
2.1
3.8
Rise Time
Fall Time
t
0.5
0.5
2.2
2.2
0.5
0.5
2.2
2.2
0.5
0.5
2.2
2.2
ns
ns
r
t
f
3/93
REV 5
Motorola, Inc. 1996
MC10H334
LOGIC DIAGRAM
17
7
OE
G
D
D
D
D
DLE
6
5
D0
D1
D2
D3
Q
Q
Q
Q
BUS0
BUS1
BUS2
BUS3
3
2
16
15
19
18
OUTPUT
LATCH
14
8
RLE
R0
G
Q
Q
Q
Q
D
D
D
D
9
R1
12
R2
13
10
1
R3
V
V
V
V
V
EE
RECEIVER
LATCH
CC
DRIVER TRUTH TABLE
RECEIVER TRUTH TABLE
4
CC01
CC02
CC03
D
DLE OE
Bus
n+1
Bus
RLE
R
n+1
11
20
X
X
H
–2.0 V
D
Bus
X
L
Bus
H
R
n
D
X
L
L
L
H
Bus
n
MOTOROLA
2–38
MC10H334
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 775–02
ISSUE C
M
S
S
0.007 (0.180)
T
L–M
N
B
Y BRK
–M–
–N–
M
S
S
0.007 (0.180)
T
L–M
N
U
D
D
–L–
Z
W
20
1
S
S
S
0.010 (0.250)
T
L–M
N
G1
X
V
VIEW D–D
M
M
S
S
S
S
A
R
0.007 (0.180)
0.007 (0.180)
T
L–M
L–M
N
N
Z
T
M
S
S
0.007 (0.180)
T
L–M
N
H
C
K1
E
K
0.004 (0.100)
–T– SEATING
G
J
PLANE
M
S
S
0.007 (0.180)
T
L–M
N
F
VIEW S
G1
VIEW S
S
S
S
0.010 (0.250)
T
L–M
N
NOTES:
1. DATUMS –L–, –M–, AND –N– DETERMINED
INCHES
MILLIMETERS
DIM
MIN
MAX
0.395
0.395
0.180
0.110
0.019
MIN
9.78
9.78
4.20
2.29
0.33
MAX
10.03
10.03
4.57
2.79
0.48
WHERE TOP OF LEAD SHOULDER EXITS PLASTIC
BODY AT MOLD PARTING LINE.
A
B
C
E
0.385
0.385
0.165
0.090
0.013
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T–, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037 (0.940).
THE DAMBAR INTRUSION(S) SHALL NOT CAUSE
THE H DIMENSION TO BE SMALLER THAN 0.025
(0.635).
F
G
H
J
K
R
U
V
W
X
Y
0.050 BSC
1.27 BSC
0.026
0.020
0.025
0.350
0.350
0.042
0.042
0.042
–––
0.032
–––
–––
0.356
0.356
0.048
0.048
0.056
0.020
10
0.66
0.51
0.64
8.89
8.89
1.07
1.07
1.07
–––
2
0.81
–––
–––
9.04
9.04
1.21
1.21
1.42
0.50
10
Z
G1
K1
2
0.310
0.040
0.330
–––
7.88
1.02
8.38
–––
2–39
MOTOROLA
MC10H334
OUTLINE DIMENSIONS
L SUFFIX
CERAMIC DIP PACKAGE
CASE 732–03
NOTES:
1. LEADS WITHIN 0.010 DIAMETER, TRUE
ISSUE E
20
1
11
10
POSITION AT SEATING PLANE, AT MAXIMUM
MATERIAL CONDITION.
2. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
3. DIMENSIONS A AND B INCLUDE MENISCUS.
B
C
INCHES
A
DIM
A
B
C
D
F
MIN
MAX
0.990
0.295
0.200
0.022
0.065
0.940
0.260
0.150
0.015
0.055
L
F
G
H
J
K
L
0.100 BSC
0.020
0.008
0.125
0.050
0.012
0.160
N
J
0.300 BSC
H
K
M
G
M
N
0
15
D
0.010
0.040
SEATING
PLANE
P SUFFIX
PLASTIC DIP PACKAGE
CASE 738–03
ISSUE E
–A–
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.
20
1
11
10
B
L
C
INCHES
MILLIMETERS
DIM
A
B
C
D
MIN
MAX
1.070
0.260
0.180
0.022
MIN
25.66
6.10
3.81
0.39
MAX
27.17
6.60
4.57
0.55
1.010
0.240
0.150
0.015
–T–
SEATING
PLANE
K
E
0.050 BSC
1.27 BSC
M
0.050
0.070
1.27
1.77
F
G
J
K
L
N
E
0.100 BSC
2.54 BSC
0.008
0.110
0.015
0.140
0.21
2.80
0.38
3.55
G
F
J 20 PL
0.300 BSC
7.62 BSC
D 20 PL
0.25 (0.010)
M
M
0.25 (0.010)
T B
M
N
0
15
0
15
0.020
0.040
0.51
1.01
M
M
T
A
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC10H334/D
◊
相关型号：
©2020 ICPDF网 联系我们和版权申明