MC12036BD [MOTOROLA]
MECL PLL COMPONENTS ±64/65, ±128/129 DUAL MODULUS PRESCALER WITH STAND-BY MODE; MECL PLL元件± 65分之64 ,± 129分之128双模预分频器与待机模式型号: | MC12036BD |
厂家: | MOTOROLA |
描述: | MECL PLL COMPONENTS ±64/65, ±128/129 DUAL MODULUS PRESCALER WITH STAND-BY MODE |
文件: | 总4页 (文件大小:101K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SEMICONDUCTOR TECHNICAL DATA
The MC12036 is a 1.1GHz ÷64/65, ÷128/129 dual modulus prescaler
used in phase–locked loop (PLL) applications. Stand–By mode is
featured to reduce current drain to 0.5mA typical when the standby pin
(SB) is switched LOW, disabling the prescaler. On–chip output
termination provides sufficient output current to drive a 12pF (typical) high
impedance load.
MECL PLL COMPONENTS
÷64/65, ÷128/129
DUAL MODULUS PRESCALER
WITH STAND–BY MODE
The MC12036A can be used with CMOS synthesizers requiring
positive edges to trigger internal counters such as Motorola’s MC145xxx
series in a PLL to provide tuning signals up to 1.1GHz in programmable
frequency steps. The MC12036B can be used with CMOS synthesizers
requiring negative edges to trigger internal counters.
A Divide Ratio Control (SW) permits selection of a 64/65 or 128/129
divide ratio as desired.
The Modulus Control (MC) selects the proper divide number after SW
has been biased to select the desired divide ratio.
P SUFFIX
8–LEAD PLASTIC PACKAGE
CASE 626–05
• 1.1GHz Toggle Frequency
• Low Power 4.0mA Typical
• Stand–By Mode
• On–Chip Output Termination
• Supply Voltage 4.5V to 5.5V
• Operating Temperature Range of –40°C to +85°C
D SUFFIX
8–LEAD PLASTIC SOIC PACKAGE
CASE 751–05
• Short Setup Time (t
) 16ns Maximum @ 1.1GHz
set
• Modulus Control Input Level is Compatible With Standard CMOS and
TTL
FUNCTION TABLE
SW
H
MC
H
Divide Ratio
Pinout: 8–Lead Plastic (Top View)
64
65
IN
8
SB
7
MC
6
GND
5
H
L
L
H
128
129
L
L
Note: SW: H = V , L = OPEN
CC
MC: H = 2.0V to V , L = GND to 0.8V
CC
1
2
3
4
IN
V
SW
OUT
CC
Design Criteria
Internal Gate Count *
Value
67
Unit
ea
Internal Gate Propagation Delay
Internal Gate Power Dissipation
Speed Power Product
200
ps
0.75
0.15
mW
pJ
*Equivalent to a two–input NAND gate.
1/97
REV 2
Motorola, Inc. 1997
MC12036A MC12036B
MAXIMUM RATINGS
Symbol
Characteristic
Range
Unit
Vdc
°C
V
CC
Power Supply Voltage, Pin 2
Operating Temperature Range
Storage Temperature Range
Modulus Control Input, Pin 6
–0.5 to +7.0
–40 to +85
–65 to +150
–0.5 to +6.5
T
A
T
stg
°C
MC
Vdc
ELECTRICAL CHARACTERISTICS (V
CC
= 4.5 to 5.5 Vdc, T = –40°C to +85°C)
A
Symbol
Characteristic
Toggle Frequency (Sine Wave Input)
Supply Current (Pin 2)
Min
0.1
—
Typ
1.4
4.0
—
Max
Unit
GHz
mA
V
f
I
1.1
6.5
t
CC
V
V
V
V
Modulus Control & Standby Input High (MC & SB)
Modulus Control & Standby Input Low (MC & SB)
Divide Ratio Control Input High (SW)
Divide Ratio Control Input Low (SW)
2.0
—
V
CC
0.8
IH1
IL1
IH2
IL2
—
V
V
CC
V
CC
V
CC
Vdc
—
OPEN
OPEN
OPEN
V
Output Voltage Swing, C = 8pF
L
1.0
—
1.4
11
—
V
p–p
ns
out
t
Modulus Setup Time MC to Out
16
SET
V
in
Input Voltage Sensitivity 250–1100 MHz
100–250 MHz
100
400
—
—
1000
1000
mVpp
ISB
Standby Current
—
0.5
—
mA
D
C
Q
D
C
Q
D
C
Q
Prop. Delay
A
B
C
In
QB
QB
QB
M
In
In
Out
MC
MC
SB
MC Setup
MC Release
D
C
Q
D
C
QB
Q
D
C
Q
D
C
QB
Q
D
C
QB
Q
D
E
F
G
H
Modulus setup time MC to out is the MC
setup or MC release plus the prop. delay.
QB
QB
Out
S
SW
Figure 1. Logic Diagram (MC12036A)
Figure 2. Modulus Setup Time
500 m
≈
20 ns
500 m
≈
20 ns
(÷64, 500MHz Input Frequency, V
CC
= 5.0V, T = 25°C,
(÷128, 1.1GHz Input Frequency, V
= 5.0V, T = 25°C,
A
CC
Output Loaded)
A
Output Loaded)
Figure 3. Typical Output Waveform
MOTOROLA
2
HIPERCOMM
BR1334 — Rev 4
MC12036A MC12036B
V
= 4.5 to 5.5 V
CC
C3
Sine Wave Generator
V
SW
CC
C1
C2
IN
IN
SB
Standby Input
50
Ω
OUT
C
L
MC
GND
EXTERNAL COMPONENTS
C1 = C2 = 1000pF
C3 = 0.1
µF
C
C
= 8pF (Including Scope
= and jig capacitance)
L
L
MC Input
Figure 4. AC Test Circuit
200
150
100
R
MHz
50
0
–50
–100
–150
–200
–250
–300
–350
–400
–450
–500
–550
–600
–650
jX
100
200
300
400
500
600
700
800
900 1000 1100 1200
Figure 5. Typical Input Impedance versus Input Frequency
HIPERCOMM
3
MOTOROLA
BR1334 — Rev 4
MC12036A MC12036B
OUTLINE DIMENSIONS
P SUFFIX
PLASTIC PACKAGE
CASE 626–05
ISSUE K
8
5
–B–
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
1
4
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
F
–A–
NOTE 2
MILLIMETERS
INCHES
DIM
A
B
C
D
F
MIN
9.40
6.10
3.94
0.38
1.02
MAX
10.16
6.60
4.45
0.51
1.78
MIN
MAX
0.400
0.260
0.175
0.020
0.070
L
0.370
0.240
0.155
0.015
0.040
C
G
H
J
K
L
2.54 BSC
0.100 BSC
J
0.76
0.20
2.92
1.27
0.30
3.43
0.030
0.008
0.115
0.050
0.012
0.135
–T–
SEATING
PLANE
N
7.62 BSC
0.300 BSC
M
D
K
M
N
–––
10
–––
10
0.76
1.01
0.030
0.040
G
H
M
M
M
0.13 (0.005)
T
A
B
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751–05
NOTES:
ISSUE R
D
A
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. DIMENSIONS ARE IN MILLIMETERS.
3. DIMENSION D AND E DO NOT INCLUDE MOLD
PROTRUSION.
8
5
C
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE B DIMENSION AT MAXIMUM MATERIAL
CONDITION.
M
M
0.25
B
H
E
1
4
MILLIMETERS
B
e
DIM
A
A1
B
C
D
MIN
1.35
0.10
0.35
0.18
4.80
3.80
MAX
1.75
0.25
0.49
0.25
5.00
4.00
h X 45
A
C
SEATING
PLANE
E
e
H
h
L
1.27 BSC
0.10
5.80
0.25
0.40
0
6.20
0.50
1.25
7
A1
B
L
M
S
S
0.25
C
B
A
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405; Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax : RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC12036A/D
◊
相关型号:
©2020 ICPDF网 联系我们和版权申明