MC74HC4002DD [MOTOROLA]

NOR Gate, HC/UH Series, 2-Func, 4-Input, CMOS, PDSO14, SOIC-14;


型号：	MC74HC4002DD
厂家：	MOTOROLA
描述：	NOR Gate, HC/UH Series, 2-Func, 4-Input, CMOS, PDSO14, SOIC-14 栅
文件：	总4页 (文件大小：142K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

SEMICONDUCTOR TECHNICAL DATA

High–Performance Silicon–Gate CMOS

The MC74HC4002 is identical in pinout to the MC14002B and

MC14002UB. The device inputs are compatible with standard CMOS

outputs; with pullup resistors, they are compatible with LSTTL outputs.

N SUFFIX

PLASTIC PACKAGE

CASE 646–06

•

Output Drive Capability: 10 LSTTL Loads

Outputs Directly Interface to CMOS, NMOS, and TTL

Operating Voltage Range: 2 to 6 V

D SUFFIX

SOIC PACKAGE

CASE 751A–03

Low Input Current: 1 µA

High Noise Immunity Characteristic of CMOS Devices

In Compliance with the Requirements Defined by JEDEC Standard

No. 7A

ORDERING INFORMATION

•

Chip Complexity: 28 FETs or 7 Equivalent Gates

MC74HCXXXXN

MC74HCXXXXD

Plastic

SOIC

LOGIC DIAGRAM

PIN ASSIGNMENT

Y = A + B + C + D

GND

PIN 14 = V

PIN 7 = GND

PINS 6, 8 = NO CONNECTION

FUNCTION TABLE

Inputs

Output

X = don’t care

10/95

REV 6

Motorola, Inc. 1995

MC74HC4002

MAXIMUM RATINGS*

Symbol

Parameter

Value

Unit

This device contains protection

circuitry to guard against damage

due to high static voltages or electric

fields. However, precautions must

be taken to avoid applications of any

voltage higher than maximum rated

voltages to this high–impedance cir-

DC Supply Voltage (Referenced to GND)

DC Input Voltage (Referenced to GND)

DC Output Voltage (Referenced to GND)

DC Input Current, per Pin

– 0.5 to + 7.0

– 1.5 to V

+ 1.5

out

– 0.5 to V

+ 0.5

± 20

cuit. For proper operation, V and

DC Output Current, per Pin

± 25

± 50

out

should be constrained to the

out

range GND (V or V

)

DC Supply Current, V

and GND Pins

in out

Unused inputs must always be

tied to an appropriate logic voltage

Power Dissipation in Still Air

Plastic DIP†

SOIC Package†

750

500

level (e.g., either GND or V ).

Unused outputs must be left open.

stg

Storage Temperature

– 65 to + 150

Lead Temperature, 1 mm from Case for 10 Seconds

(Plastic DIP or SOIC Package)

260

* Maximum Ratings are those values beyond which damage to the device may occur.

Functional operation should be restricted to the Recommended Operating Conditions.

†Derating — Plastic DIP: – 10 mW/ C from 65 to 125 C

SOIC Package: – 7 mW/ C from 65 to 125 C

For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

RECOMMENDED OPERATING CONDITIONS

Symbol

Parameter

Min

2.0

Max

Unit

DC Supply Voltage (Referenced to GND)

DC Input Voltage, Output Voltage (Referenced to GND)

Operating Temperature, All Package Types

6.0

V , V

in out

– 55 + 125

t , t

r f

Input Rise and Fall Time

(Figure 1)

= 2.0 V

= 4.5 V

= 6.0 V

1000

500

400

DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)

Guaranteed Limit

– 55 to

25 C

Symbol

Parameter

Test Conditions

Unit

85 C

125 C

Minimum High–Level Input

Voltage

= 0.1 V or V

– 0.1 V

2.0

4.5

6 0

1.5

3.15

4.2

1.5

3.15

4.2

1.5

3.15

4.2

out

20 µA

out

Maximum Low–Level Input

Voltage

= 0.1 V or V

– 0.1 V

2.0

4.5

6.0

0.3

0.9

1.2

0.3

0.9

1.2

0.3

0.9

1.2

out

20 µA

out

Minimum High–Level Output

Voltage

= V or V

IH IL

2.0

4.5

6.0

1.9

4.4

5.9

1.9

4.4

5.9

1.9

4.4

5.9

20 µA

out

= V or V

4.0 mA

5.2 mA

4.5

6.0

3.98

5.48

3.84

5.34

3.70

5.20

IH IL out

out

Maximum Low–Level Output

Voltage

= V or V

IH IL

2.0

4.5

6.0

0.1

20 µA

out

= V or V

4.0 mA

5.2 mA

4.5

6.0

0.26

0.33

0.40

IH IL out

out

Maximum Input Leakage Current

= V

or GND

6.0

± 0.1

± 1.0

µA

Maximum Quiescent Supply

Current (per Package)

or GND

= 0 µA

out

NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

MOTOROLA

High–Speed CMOS Logic Data

DL129 — Rev 6

MC74HC4002

AC ELECTRICAL CHARACTERISTICS (C = 50 pF, Input t = t = 6 ns)

Guaranteed Limit

– 55 to

25 C

Symbol

Parameter

Unit

85 C

125 C

Maximum Propagation Delay, Any Input to Output Y

(Figures 1 and 2)

2.0

4.5

6.0

120

150

180

PLH

PHL

Maximum Output Transition Time, Any Output

(Figures 1 and 2)

2.0

4.5

6 0

110

TLH

THL

Maximum Input Capacitance

—

NOTES:

1. For propagation delays with loads other than 50 pF, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

2. Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

Typical @ 25°C, V

= 5.0 V

Power Dissipation Capacitance (Per Gate)*

* Used to determine the no–load dynamic power consumption: P = C

Motorola High–Speed CMOS Data Book (DL129/D).

f + I

V . For load considerations, see Chapter 2 of the

CC CC

PD CC

TEST POINT

INPUT 90%

50%

10%

OUTPUT

DEVICE

UNDER

A, B, C, OR D

GND

C *

PHL

PLH

TEST

90%

50%

10%

OUTPUT Y

THL

TLH

* Includes all probe and jig capacitance

Figure 1.

Figure 2. Test Circuit

EXPANDED LOGIC DIAGRAM

(1/2 of the Device)

High–Speed CMOS Logic Data

DL129 — Rev 6

MOTOROLA

MC74HC4002

OUTLINE DIMENSIONS

N SUFFIX

PLASTIC DIP PACKAGE

CASE 646–06

NOTES:

1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE

POSITION AT SEATING PLANE AT MAXIMUM

MATERIAL CONDITION.

ISSUE L

2. DIMENSION L TO CENTER OF LEADS WHEN

FORMED PARALLEL.

3. DIMENSION B DOES NOT INCLUDE MOLD

FLASH.

4. ROUNDED CORNERS OPTIONAL.

INCHES

MILLIMETERS

DIM

MIN

MAX

0.770

0.260

0.185

0.021

0.070

MIN

18.16

6.10

3.69

0.38

1.02

MAX

19.56

6.60

4.69

0.53

1.78

0.715

0.240

0.145

0.015

0.040

0.100 BSC

2.54 BSC

0.052

0.008

0.115

0.095

0.015

0.135

1.32

0.20

2.92

2.41

0.38

3.43

0.300 BSC

7.62 BSC

SEATING

PLANE

0.015

0.039

0.39

1.01

D SUFFIX

PLASTIC SOIC PACKAGE

CASE 751A–03

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

ISSUE F

–A–

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSIONS A AND B DO NOT INCLUDE

MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)

PER SIDE.

5. DIMENSION D DOES NOT INCLUDE DAMBAR

PROTRUSION. ALLOWABLE DAMBAR

PROTRUSION SHALL BE 0.127 (0.005) TOTAL

IN EXCESS OF THE D DIMENSION AT

MAXIMUM MATERIAL CONDITION.

P 7 PL

–B–

0.25 (0.010)

MILLIMETERS

INCHES

R X 45°

DIM

MIN

8.55

3.80

1.35

0.35

0.40

MAX

8.75

4.00

1.75

0.49

1.25

MIN

MAX

0.344

0.157

0.068

0.019

0.049

0.337

0.150

0.054

0.014

0.016

SEATING

PLANE

D 14 PL

0.25 (0.010)

1.27 BSC

0.050 BSC

0.19

0.10

0.25

0.008

0.004

0.009

5.80

0.25

6.20

0.50

7°

0.244

0.019

0.228

0.010

Motorolareserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representationorguaranteeregarding

the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,

andspecifically disclaims any and all liability, includingwithoutlimitationconsequentialorincidentaldamages. “Typical” parameters can and do vary in different

applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does

not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in

systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of

the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such

unintendedor unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless

against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.

Motorola and

are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.

How to reach us:

USA/EUROPE: Motorola Literature Distribution;

JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447

6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315

MFAX: RMFAX0@email.sps.mot.com –TOUCHTONE (602) 244–6609

INTERNET: http://Design–NET.com

HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

CODELINE

MC74HC4002/D

High–Speed CMOS Logic Data

DL129 — Rev 6

◊

MOTOROLA

MC74HC4002DD [MOTOROLA]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB