MC908GZ32MFJ [MOTOROLA]
Microcontrollers; 微控制器型号: | MC908GZ32MFJ |
厂家: | MOTOROLA |
描述: | Microcontrollers |
文件: | 总380页 (文件大小:5433K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Freescale Semiconductor, Inc.
MC68HC908GZ60
MC68HC908GZ48
MC68HC908GZ32
Data Sheet
M68HC08
Microcontrollers
MC68HC908GZ60/D
Rev. 1.0
5/2004
MOTOROLA.COM/SEMICONDUCTORS
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC68HC908GZ60
MC68HC908GZ48
MC68HC908GZ32
Data Sheet
To provide the most up-to-date information, the revision of our documents on the
World Wide Web will be the most current. Your printed copy may be an earlier
revision. To verify you have the latest information available, refer to:
http://motorola.com/semiconductors
The following revision history table summarizes changes contained in this
document. For your convenience, the page number designators have been linked
to the appropriate location.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA
Data Sheet
3
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Revision History
Revision History
Description
Revision
Level
Page
Number(s)
Date
April,
2004
N/A
Initial release
N/A
132
9.7.3 Keyboard Interrupt Polarity Register — Corrected the bit description
of the KBIP7–KBIP0 bits.
14.8.8 ESCI Prescaler Register — Reworked note under PDS2–PDS0
description for clarity.
234
367
367
374
374
378
378
Table 22-1. MC Order Numbers — Corrected order numbers.
Figure 22-1. Device Numbering System — Reworked diagram to reflect
correct order numbers.
May,
2004
1.0
Table A-1. MC Order Numbers — Corrected order numbers.
Figure A-3. Device Numbering System — Reworked diagram to reflect
correct order numbers.
B.4 Ordering Information — Corrected order numbers.
Figure B-3. Device Numbering System — Reworked diagram to reflect
correct order numbers.
Data Sheet
4
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Revision History
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
List of Sections
Section 1. General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Section 2. Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Section 3. Analog-to-Digital Converter (ADC) . . . . . . . . . . . . . . . . . . .65
Section 4. Clock Generator Module (CGM). . . . . . . . . . . . . . . . . . . . . .79
Section 5. Configuration Register (CONFIG) . . . . . . . . . . . . . . . . . . . .99
Section 6. Computer Operating Properly (COP) Module. . . . . . . . . .103
Section 7. Central Processor Unit (CPU) . . . . . . . . . . . . . . . . . . . . . .107
Section 8. External Interrupt (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Section 9. Keyboard Interrupt Module (KBI) . . . . . . . . . . . . . . . . . . .125
Section 10. Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
Section 11. Low-Voltage Inhibit (LVI) . . . . . . . . . . . . . . . . . . . . . . . . .141
Section 12. MSCAN08 Controller (MSCAN08) . . . . . . . . . . . . . . . . . .145
Section 13. Input/Output (I/O) Ports . . . . . . . . . . . . . . . . . . . . . . . . . .183
Section 14. Enhanced Serial Communications
Interface (ESCI) Module . . . . . . . . . . . . . . . . . . . . . . . . .205
Section 15. System Integration Module (SIM) . . . . . . . . . . . . . . . . . .241
Section 16. Serial Peripheral Interface (SPI) Module. . . . . . . . . . . . .261
Section 17. Timebase Module (TBM). . . . . . . . . . . . . . . . . . . . . . . . . .285
Section 18. Timer Interface Module (TIM1). . . . . . . . . . . . . . . . . . . . .291
Section 19. Timer Interface Module (TIM2). . . . . . . . . . . . . . . . . . . . .309
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
5
MOTOROLA
List of Sections
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
List of Sections
Section 20. Development Support. . . . . . . . . . . . . . . . . . . . . . . . . . . .333
Section 21. Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . .351
Section 22. Ordering Information
and Mechanical Specifications . . . . . . . . . . . . . . . . . . .367
Appendix A. MC68HC908GZ48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .371
Appendix B. MC68HC908GZ32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .375
Data Sheet
6
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
List of Sections
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Table of Contents
Section 1. General Description
1.1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1.2
1.2.1
1.2.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Features of the CPU08. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.3
1.4
MCU Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.5
Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Power Supply Pins (VDD and VSS) . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Oscillator Pins (OSC1 and OSC2) . . . . . . . . . . . . . . . . . . . . . . . . . . 29
External Reset Pin (RST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
External Interrupt Pin (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CGM Power Supply Pins (VDDA and VSSA) . . . . . . . . . . . . . . . . . . . 29
External Filter Capacitor Pin (CGMXFC) . . . . . . . . . . . . . . . . . . . . . 30
ADC Power Supply/Reference Pins
1.5.1
1.5.2
1.5.3
1.5.4
1.5.5
1.5.6
1.5.7
(VDDAD/VREFH and VSSAD/VREFL) . . . . . . . . . . . . . . . . . . . . . . . . 30
Port A Input/Output (I/O) Pins
1.5.8
(PTA7/KBD7/AD15–PTA0/KBD0/AD8) . . . . . . . . . . . . . . . . . . . . 30
Port B I/O Pins (PTB7/AD7–PTB0/AD0). . . . . . . . . . . . . . . . . . . . . . 30
Port C I/O Pins (PTC6–PTC0/CANTX). . . . . . . . . . . . . . . . . . . . . . . 30
Port D I/O Pins (PTD7/T2CH1–PTD0/SS) . . . . . . . . . . . . . . . . . . . . 31
Port E I/O Pins (PTE5–PTE2, PTE1/RxD, and PTE0/TxD) . . . . . . . 31
Port F I/O Pins (PTF7/T2CH5–PTF0). . . . . . . . . . . . . . . . . . . . . . . . 31
Port G I/O Pins (PTG7/AD23–PTBG0/AD16). . . . . . . . . . . . . . . . . . 31
1.5.9
1.5.10
1.5.11
1.5.12
1.5.13
1.5.14
Section 2. Memory
2.1
2.2
2.3
2.4
2.5
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Unimplemented Memory Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Reserved Memory Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Input/Output (I/O) Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Random-Access Memory (RAM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
2.6
FLASH-1 Memory (FLASH-1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
FLASH-1 Control and Block Protect Registers. . . . . . . . . . . . . . . . . 49
FLASH-1 Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
FLASH-1 Block Protect Register. . . . . . . . . . . . . . . . . . . . . . . . . . 50
FLASH-1 Block Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
2.6.1
2.6.2
2.6.2.1
2.6.2.2
2.6.3
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
7
MOTOROLA
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
2.6.4
2.6.5
2.6.6
2.6.7
2.6.7.1
2.6.7.2
FLASH-1 Mass Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
FLASH-1 Page Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
FLASH-1 Program Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Stop Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
2.7
FLASH-2 Memory (FLASH-2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
FLASH-2 Control and Block Protect Registers. . . . . . . . . . . . . . . . . 57
FLASH-2 Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
FLASH-2 Block Protect Register. . . . . . . . . . . . . . . . . . . . . . . . . . 58
FLASH-2 Block Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
FLASH-2 Mass Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
FLASH-2 Page Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
FLASH-2 Program Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Stop Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
2.7.1
2.7.2
2.7.2.1
2.7.2.2
2.7.3
2.7.4
2.7.5
2.7.6
2.7.7
2.7.7.1
2.7.7.2
Section 3. Analog-to-Digital Converter (ADC)
3.1
3.2
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
3.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
ADC Port I/O Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Voltage Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Conversion Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Accuracy and Precision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Result Justification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.3.6
3.4
3.5
Monotonicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
3.6
3.6.1
3.6.2
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
3.7
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
ADC Analog Power Pin (VDDAD). . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
ADC Analog Ground Pin (VSSAD) . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
ADC Voltage Reference High Pin (VREFH) . . . . . . . . . . . . . . . . . . . . 71
ADC Voltage Reference Low Pin (VREFL) . . . . . . . . . . . . . . . . . . . . 71
ADC Voltage In (VADIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
3.7.1
3.7.2
3.7.3
3.7.4
3.7.5
3.8
3.8.1
I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
ADC Status and Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Data Sheet
8
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Table of Contents
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
3.8.2
ADC Data Register High and Data Register Low . . . . . . . . . . . . . . . 74
Left Justified Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Right Justified Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Left Justified Signed Data Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Eight Bit Truncation Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
ADC Clock Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
3.8.2.1
3.8.2.2
3.8.2.3
3.8.2.4
3.8.3
Section 4. Clock Generator Module (CGM)
4.1
4.2
4.3
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Crystal Oscillator Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Phase-Locked Loop Circuit (PLL). . . . . . . . . . . . . . . . . . . . . . . . . . . 81
PLL Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Acquisition and Tracking Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Manual and Automatic PLL Bandwidth Modes. . . . . . . . . . . . . . . . . 82
Programming the PLL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Special Programming Exceptions. . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Base Clock Selector Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
CGM External Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Crystal Amplifier Input Pin (OSC1) . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Crystal Amplifier Output Pin (OSC2) . . . . . . . . . . . . . . . . . . . . . . . . 88
External Filter Capacitor Pin (CGMXFC) . . . . . . . . . . . . . . . . . . . . . 88
PLL Analog Power Pin (VDDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
PLL Analog Ground Pin (VSSA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Oscillator Enable Signal (SIMOSCEN). . . . . . . . . . . . . . . . . . . . . . . 88
Oscillator Enable in Stop Mode Bit (OSCENINSTOP) . . . . . . . . . . . 88
Crystal Output Frequency Signal (CGMXCLK). . . . . . . . . . . . . . . . . 89
CGM Base Clock Output (CGMOUT). . . . . . . . . . . . . . . . . . . . . . . . 89
CGM CPU Interrupt (CGMINT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
CGM Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
PLL Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
PLL Bandwidth Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
PLL Multiplier Select Register High . . . . . . . . . . . . . . . . . . . . . . . . . 93
PLL Multiplier Select Register Low. . . . . . . . . . . . . . . . . . . . . . . . . . 94
PLL VCO Range Select Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Special Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
CGM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Acquisition/Lock Time Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Acquisition/Lock Time Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Parametric Influences on Reaction Time . . . . . . . . . . . . . . . . . . . . . 97
Choosing a Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.3.7
4.3.8
4.3.9
4.4
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
4.4.7
4.4.8
4.4.9
4.4.10
4.5
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
4.6
4.7
4.7.1
4.7.2
4.7.3
4.8
4.8.1
4.8.2
4.8.3
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
9
MOTOROLA
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
Section 5. Configuration Register (CONFIG)
5.1
5.2
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Section 6. Computer Operating Properly (COP) Module
6.1
6.2
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
6.3
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
CGMXCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
STOP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
COPCTL Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Internal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
COPD (COP Disable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
COPRS (COP Rate Select) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
6.3.1
6.3.2
6.3.3
6.3.4
6.3.5
6.3.6
6.3.7
6.4
6.5
6.6
COP Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
6.7
6.7.1
6.7.2
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
6.8
COP Module During Break Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Section 7. Central Processor Unit (CPU)
7.1
7.2
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
7.3
CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Index Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Stack Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Program Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Condition Code Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
7.3.1
7.3.2
7.3.3
7.3.4
7.3.5
7.4
Arithmetic/Logic Unit (ALU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
7.5
7.5.1
7.5.2
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
7.6
7.7
7.8
CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Opcode Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Data Sheet
10
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Table of Contents
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
Section 8. External Interrupt (IRQ)
8.1
8.2
8.3
8.4
8.5
8.6
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
IRQ Pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
IRQ Module During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 123
IRQ Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Section 9. Keyboard Interrupt Module (KBI)
9.1
9.2
9.3
9.4
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Keyboard Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
9.5
9.5.1
9.5.2
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
9.6
Keyboard Module During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . 130
9.7
I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Keyboard Status and Control Register . . . . . . . . . . . . . . . . . . . . . . 130
Keyboard Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . . . . . 131
Keyboard Interrupt Polarity Register. . . . . . . . . . . . . . . . . . . . . . . . 132
9.7.1
9.7.2
9.7.3
Section 10. Low-Power Modes
10.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
10.1.1
10.1.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
10.2 Analog-to-Digital Converter (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
10.2.1
10.2.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
10.3 Break Module (BRK). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
10.3.1
10.3.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
10.4 Central Processor Unit (CPU). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
10.4.1
10.4.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
10.5 Clock Generator Module (CGM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
10.5.1
10.5.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
10.6 Computer Operating Properly Module (COP). . . . . . . . . . . . . . . . . . . . 135
10.6.1
10.6.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
11
MOTOROLA
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
10.7 External Interrupt Module (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
10.7.1
10.7.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
10.8 Keyboard Interrupt Module (KBI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
10.8.1
10.8.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
10.9 Low-Voltage Inhibit Module (LVI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
10.9.1
10.9.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
10.10 Enhanced Serial Communications Interface Module (ESCI) . . . . . . . . 136
10.10.1
10.10.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
10.11 Serial Peripheral Interface Module (SPI) . . . . . . . . . . . . . . . . . . . . . . . 137
10.11.1
10.11.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
10.12 Timer Interface Module (TIM1 and TIM2). . . . . . . . . . . . . . . . . . . . . . . 137
10.12.1
10.12.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
10.13 Timebase Module (TBM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
10.13.1
10.13.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
10.14 Motorola Scalable Controller Area Network Module (MSCAN) . . . . . . 138
10.14.1
10.14.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
10.15 Exiting Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
10.16 Exiting Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Section 11. Low-Voltage Inhibit (LVI)
11.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
11.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
11.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
11.3.1
11.3.2
11.3.3
11.3.4
Polled LVI Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Forced Reset Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Voltage Hysteresis Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
LVI Trip Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
11.4 LVI Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
11.5 LVI Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
11.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
11.6.1
11.6.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Data Sheet
12
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Table of Contents
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
Section 12. MSCAN08 Controller (MSCAN08)
12.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
12.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
12.3 External Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
12.4 Message Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
12.4.1
12.4.2
12.4.3
Background. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Receive Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Transmit Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
12.5 Identifier Acceptance Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
12.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
12.6.1
12.6.2
Interrupt Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Interrupt Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
12.7 Protocol Violation Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
12.8 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
12.8.1
12.8.2
12.8.3
12.8.4
12.8.5
MSCAN08 Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
MSCAN08 Soft Reset Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
MSCAN08 Power-Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
CPU Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Programmable Wakeup Function . . . . . . . . . . . . . . . . . . . . . . . . . . 159
12.9 Timer Link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
12.10 Clock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
12.11 Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
12.12 Programmer’s Model of Message Storage. . . . . . . . . . . . . . . . . . . . . . 164
12.12.1
12.12.2
12.12.3
12.12.4
12.12.5
Message Buffer Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Identifier Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Data Length Register (DLR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Data Segment Registers (DSRn) . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Transmit Buffer Priority Registers. . . . . . . . . . . . . . . . . . . . . . . . . . 167
12.13 Programmer’s Model of Control Registers . . . . . . . . . . . . . . . . . . . . . . 168
12.13.1
12.13.2
12.13.3
12.13.4
12.13.5
12.13.6
12.13.7
12.13.8
12.13.9
MSCAN08 Module Control Register 0 . . . . . . . . . . . . . . . . . . . . . . 169
MSCAN08 Module Control Register 1 . . . . . . . . . . . . . . . . . . . . . . 171
MSCAN08 Bus Timing Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . 172
MSCAN08 Bus Timing Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . 173
MSCAN08 Receiver Flag Register (CRFLG) . . . . . . . . . . . . . . . . . 174
MSCAN08 Receiver Interrupt Enable Register . . . . . . . . . . . . . . . 176
MSCAN08 Transmitter Flag Register . . . . . . . . . . . . . . . . . . . . . . . 177
MSCAN08 Transmitter Control Register. . . . . . . . . . . . . . . . . . . . . 178
MSCAN08 Identifier Acceptance Control Register . . . . . . . . . . . . . 179
12.13.10 MSCAN08 Receive Error Counter . . . . . . . . . . . . . . . . . . . . . . . . . 180
12.13.11 MSCAN08 Transmit Error Counter. . . . . . . . . . . . . . . . . . . . . . . . . 180
12.13.12 MSCAN08 Identifier Acceptance Registers . . . . . . . . . . . . . . . . . . 181
12.13.13 MSCAN08 Identifier Mask Registers (CIDMR0–CIDMR3) . . . . . . . 182
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
13
MOTOROLA
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
Section 13. Input/Output (I/O) Ports
13.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
13.2 Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
13.2.1
13.2.2
13.2.3
Port A Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Data Direction Register A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Port A Input Pullup Enable Register . . . . . . . . . . . . . . . . . . . . . . . . 189
13.3 Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
13.3.1
13.3.2
Port B Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Data Direction Register B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
13.4 Port C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
13.4.1
13.4.2
13.4.3
Port C Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Data Direction Register C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Port C Input Pullup Enable Register. . . . . . . . . . . . . . . . . . . . . . . . 194
13.5 Port D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
13.5.1
13.5.2
13.5.3
Port D Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Data Direction Register D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Port D Input Pullup Enable Register. . . . . . . . . . . . . . . . . . . . . . . . 197
13.6 Port E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
13.6.1
13.6.2
Port E Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Data Direction Register E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
13.7 Port F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
13.7.1
13.7.2
Port F Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Data Direction Register F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
13.8 Port G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
13.8.1
13.8.2
Port G Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Data Direction Register G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Section 14. Enhanced Serial Communications
Interface (ESCI) Module
14.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
14.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
14.3 Pin Name Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
14.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
14.4.1
14.4.2
Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Character Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Character Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Break Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Idle Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Inversion of Transmitted Output . . . . . . . . . . . . . . . . . . . . . . . . . 213
Transmitter Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
Character Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
Character Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
14.4.2.1
14.4.2.2
14.4.2.3
14.4.2.4
14.4.2.5
14.4.2.6
14.4.3
14.4.3.1
14.4.3.2
Data Sheet
14
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Table of Contents
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
14.4.3.3
14.4.3.4
14.4.3.5
14.4.3.6
14.4.3.7
14.4.3.8
Data Sampling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
Framing Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Baud Rate Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Receiver Wakeup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Receiver Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Error Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
14.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
14.5.1
14.5.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
14.6 ESCI During Break Module Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . 221
14.7 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
14.7.1
14.7.2
PTE0/TxD (Transmit Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
PTE1/RxD (Receive Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
14.8 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
14.8.1
14.8.2
14.8.3
14.8.4
14.8.5
14.8.6
14.8.7
14.8.8
ESCI Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
ESCI Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
ESCI Control Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
ESCI Status Register 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
ESCI Status Register 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
ESCI Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
ESCI Baud Rate Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
ESCI Prescaler Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
14.9 ESCI Arbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
14.9.1
14.9.2
14.9.3
14.9.4
ESCI Arbiter Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
ESCI Arbiter Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
Bit Time Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
Arbitration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Section 15. System Integration Module (SIM)
15.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
15.2 SIM Bus Clock Control and Generation . . . . . . . . . . . . . . . . . . . . . . . . 244
15.2.1
15.2.2
15.2.3
Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
Clock Startup from POR or LVI Reset . . . . . . . . . . . . . . . . . . . . . . 244
Clocks in Stop Mode and Wait Mode . . . . . . . . . . . . . . . . . . . . . . . 244
15.3 Reset and System Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
15.3.1
15.3.2
External Pin Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Active Resets from Internal Sources . . . . . . . . . . . . . . . . . . . . . . . 246
Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Computer Operating Properly (COP) Reset . . . . . . . . . . . . . . . . 248
Illegal Opcode Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Illegal Address Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Low-Voltage Inhibit (LVI) Reset . . . . . . . . . . . . . . . . . . . . . . . . . 248
Monitor Mode Entry Module Reset (MODRST). . . . . . . . . . . . . . 248
15.3.2.1
15.3.2.2
15.3.2.3
15.3.2.4
15.3.2.5
15.3.2.6
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
15
MOTOROLA
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
15.4 SIM Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
15.4.1
15.4.2
15.4.3
SIM Counter During Power-On Reset . . . . . . . . . . . . . . . . . . . . . . 249
SIM Counter During Stop Mode Recovery . . . . . . . . . . . . . . . . . . . 249
SIM Counter and Reset States. . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
15.5 Exception Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
15.5.1
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
Hardware Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
SWI Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Interrupt Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
Status Flag Protection in Break Mode . . . . . . . . . . . . . . . . . . . . . . 255
15.5.1.1
15.5.1.2
15.5.1.3
15.5.2
15.5.3
15.5.4
15.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
15.6.1
15.6.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
15.7 SIM Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
15.7.1
15.7.2
15.7.3
Break Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
SIM Reset Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Break Flag Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
Section 16. Serial Peripheral Interface (SPI) Module
16.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
16.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
16.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
16.3.1
16.3.2
Master Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
Slave Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
16.4 Transmission Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266
16.4.1
16.4.2
16.4.3
16.4.4
Clock Phase and Polarity Controls . . . . . . . . . . . . . . . . . . . . . . . . . 266
Transmission Format When CPHA = 0. . . . . . . . . . . . . . . . . . . . . . 266
Transmission Format When CPHA = 1. . . . . . . . . . . . . . . . . . . . . . 267
Transmission Initiation Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
16.5 Queuing Transmission Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
16.6 Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
16.6.1
16.6.2
Overflow Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Mode Fault Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
16.7 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
16.8 Resetting the SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
16.9 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
16.9.1
16.9.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
16.10 SPI During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
16.11 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
16.11.1
16.11.2
MISO (Master In/Slave Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
MOSI (Master Out/Slave In) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
Data Sheet
16
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Table of Contents
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
16.11.3
16.11.4
SPSCK (Serial Clock). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
SS (Slave Select) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
16.12 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
16.12.1
16.12.2
16.12.3
SPI Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
SPI Status and Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . 280
SPI Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Section 17. Timebase Module (TBM)
17.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
17.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
17.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
17.4 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
17.5 TBM Interrupt Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
17.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
17.6.1
17.6.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
17.7 Timebase Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
Section 18. Timer Interface Module (TIM1)
18.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
18.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
18.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
18.3.1
18.3.2
18.3.3
18.3.3.1
18.3.3.2
18.3.4
18.3.4.1
18.3.4.2
18.3.4.3
TIM1 Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
Unbuffered Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
Buffered Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
Pulse Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
Unbuffered PWM Signal Generation. . . . . . . . . . . . . . . . . . . . . . 297
Buffered PWM Signal Generation. . . . . . . . . . . . . . . . . . . . . . . . 298
PWM Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
18.4 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
18.5 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
18.6 TIM1 During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
18.7 Input/Output Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
18.8 Input/Output Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
18.8.1
18.8.2
18.8.3
18.8.4
18.8.5
TIM1 Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . 300
TIM1 Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
TIM1 Counter Modulo Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . 303
TIM1 Channel Status and Control Registers . . . . . . . . . . . . . . . . . 303
TIM1 Channel Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
17
MOTOROLA
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
Section 19. Timer Interface Module (TIM2)
19.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
19.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
19.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
19.3.1
19.3.2
19.3.3
19.3.3.1
19.3.3.2
19.3.4
19.3.4.1
19.3.4.2
19.3.4.3
TIM2 Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
Unbuffered Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
Buffered Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
Pulse Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Unbuffered PWM Signal Generation. . . . . . . . . . . . . . . . . . . . . . 318
Buffered PWM Signal Generation. . . . . . . . . . . . . . . . . . . . . . . . 318
PWM Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
19.4 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
19.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
19.5.1
19.5.2
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
19.6 TIM2 During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
19.7 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
19.7.1
19.7.2
TIM2 Clock Pin (T2CH0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
TIM2 Channel I/O Pins (T2CH5:T2CH2 and T2CH1:T2CH0) . . . . 322
19.8 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
19.8.1
19.8.2
19.8.3
19.8.4
19.8.5
TIM2 Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . 323
TIM2 Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
TIM2 Counter Modulo Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . 325
TIM2 Channel Status and Control Registers . . . . . . . . . . . . . . . . . 326
TIM2 Channel Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Section 20. Development Support
20.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
20.2 Break Module (BRK). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
20.2.1
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
Flag Protection During Break Interrupts . . . . . . . . . . . . . . . . . . . 336
TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
COP During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Break Module Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
Break Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . 337
Break Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
Break Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
Break Flag Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
20.2.1.1
20.2.1.2
20.2.1.3
20.2.2
20.2.2.1
20.2.2.2
20.2.2.3
20.2.2.4
20.2.3
20.3 Monitor Module (MON). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
20.3.1
20.3.1.1
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
Normal Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
Data Sheet
18
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Table of Contents
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
20.3.1.2
20.3.1.3
20.3.1.4
20.3.1.5
20.3.1.6
20.3.1.7
20.3.2
Forced Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
Monitor Vectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
Break Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346
Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
Section 21. Electrical Specifications
21.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351
21.2 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351
21.3 Functional Operating Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
21.4 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
21.5 5.0-Vdc Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
21.6 3.3-Vdc Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
21.7 5.0-Volt Control Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
21.8 3.3-Volt Control Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
21.9 Clock Generation Module (CGM) Characteristics. . . . . . . . . . . . . . . . . 358
21.9.1
21.9.2
CGM Component Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 358
CGM Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
21.10 5.0-Volt ADC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
21.11 3.3-Volt ADC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
21.12 5.0-Volt SPI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
21.13 3.3-Volt SPI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362
21.14 Timer Interface Module Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 365
21.15 Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
Section 22. Ordering Information
and Mechanical Specifications
22.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
22.2 MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
22.3 32-Pin Low-Profile Quad Flat Pack (LQFP) . . . . . . . . . . . . . . . . . . . . . 368
22.4 48-Pin Low-Profile Quad Flat Pack (LQFP) . . . . . . . . . . . . . . . . . . . . . 369
22.5 64-Pin Quad Flat Pack (QFP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
Appendix A. MC68HC908GZ48
A.1
A.2
A.3
A.4
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
19
MOTOROLA
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Table of Contents
Appendix B. MC68HC908GZ32
B.1
B.2
B.3
B.4
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378
Data Sheet
20
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Table of Contents
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 1. General Description
1.1 Introduction
The MC68HC908GZ60, MC68HC908GZ48, and MC68HC908GZ32 are members
of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units
(MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit
(CPU08) and are available with a variety of modules, memory sizes and types, and
package types.
The information contained in this document pertains to all three devices with the
exceptions noted in Appendix A. MC68HC908GZ48 and Appendix B.
MC68HC908GZ32.
1.2 Features
For convenience, features have been organized to reflect:
•
•
Standard features
Features of the CPU08
1.2.1 Standard Features
Features of the MC68HC908GZ60 include:
•
•
High-performance M68HC08 architecture optimized for C-compilers
Fully upward-compatible object code with M6805, M146805, and M68HC05
Families
•
•
•
8-MHz internal bus frequency
Clock generation module supporting 1-MHz to 8-MHz crystals
MSCAN08 (Motorola scalable controller area network) controller
(implementing 2.0b protocol as defined in BOSCH specification dated
September 1991)
•
•
FLASH program memory security(1)
On-chip programming firmware for use with host personal computer which
does not require high voltage for entry
•
In-system programming (ISP)
1. No security feature is absolutely secure. However, Motorola’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
21
MOTOROLA
General Description
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
•
System protection features:
–
–
Optional computer operating properly (COP) reset
Low-voltage detection with optional reset and selectable trip points for
3.3-V and 5.0-V operation
–
–
Illegal opcode detection with reset
Illegal address detection with reset
•
•
Low-power design; fully static with stop and wait modes
Standard low-power modes of operation:
–
–
Wait mode
Stop mode
•
•
Master reset pin and power-on reset (POR)
On-chip FLASH memory:
–
–
–
MC68HC908GZ60 — 60 Kbytes
MC68HC908GZ48 — 48 Kbytes
MC68HC908GZ32 — 32 Kbytes
•
Random-access memory (RAM):
–
–
–
MC68HC908GZ60 — 2048 bytes
MC68HC908GZ48 — 1536 bytes
MC68HC908GZ32 — 1536 bytes
•
•
•
Serial peripheral interface (SPI) module
Enhanced serial communications interface (ESCI) module
One 16-bit, 2-channel timer interface module (TIM1) with selectable input
capture, output compare, and pulse-width modulation (PWM) capability on
each channel
•
•
One 16-bit, 6-channel timer interface module (TIM2) with selectable input
capture, output compare, and pulse-width modulation (PWM) capability on
each channel
Timebase module with clock prescaler circuitry for eight user selectable
periodic real-time interrupts with optional active clock source during stop
mode for periodic wakeup from stop using an external crystal
•
•
•
24-channel, 10-bit successive approximation analog-to-digital converter
(ADC)
8-bit keyboard wakeup port with software selectable rising or falling edge
detect, as well as high or low level detection
Up to 53 general-purpose input/output (I/O) pins, including:
–
–
40 shared-function I/O pins, depending on package choice
Up to 13 dedicated I/O pins, depending on package choice
•
Selectable pullups on inputs only on ports A, C, and D. Selection is on an
individual port bit basis. During output mode, pullups are disengaged.
•
•
Internal pullups on IRQ and RST to reduce customer system cost
High current 10-mA sink/source capability on all port pins
Data Sheet
22
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
General Description
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
Features
•
•
Higher current 20-mA sink/source capability on PTC0–PTC4 and
PTF0–PTF3
User selectable clockout feature with divide by 1, 2, and 4 of the bus or
crystal frequency
•
•
User selection of having the oscillator enabled or disabled during stop mode
BREAK module (BRK) to allow single breakpoint setting during
in-circuit debugging
•
Available packages:
–
–
–
32-pin low-profile quad flat pack (LQFP)
48-pin low-profile quad flat pack (LQFP)
64-pin quad flat pack (QFP)
•
Specific features in 32-pin LQFP are:
–
–
–
–
Port A is only 4 bits: PTA0–PTA3; shared with ADC and KBI modules
Port B is only 6 bits: PTB0–PTB5; shared with ADC module
Port C is only 2 bits: PTC0–PTC1; shared with MSCAN module
Port D is only 7 bits: PTD0–PTD6; shared with SPI, TIM1 and TIM2
modules
–
Port E is only 2 bits: PTE0–PTE1; shared with ESCI module
•
•
Specific features in 48-pin LQFP are:
–
–
–
–
–
Port A is 8 bits: PTA0–PTA7; shared with ADC and KBI modules
Port B is 8 bits: PTB0–PTB7; shared with ADC module
Port C is only 7 bits: PTC0–PTC6; shared with MSCAN module
Port D is 8 bits: PTD0–PTD7; shared with SPI, TIM1, and TIM2 modules
Port E is only 6 bits: PTE0–PTE5; shared with ESCI module
Specific features in 64-pin QFP are:
–
–
–
–
–
–
–
Port A is 8 bits: PTA0–PTA7; shared with ADC and KBI modules
Port B is 8 bits: PTB0–PTB7; shared with ADC module
Port C is only 7 bits: PTC0–PTC6; shared with MSCAN module
Port D is 8 bits: PTD0–PTD7; shared with SPI, TIM1, andTIM2 modules
Port E is only 6 bits: PTE0–PTE5; shared with ESCI module
Port F is 8 bits: PTF0–PTF7; shared with TIM2 module
Port G is 8 bits; PTG0–PTG7; shared with ADC module
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
23
MOTOROLA
General Description
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
1.2.2 Features of the CPU08
Features of the CPU08 include:
•
•
•
•
•
•
•
•
•
•
Enhanced HC05 programming model
Extensive loop control functions
16 addressing modes (eight more than the HC05)
16-bit index register and stack pointer
Memory-to-memory data transfers
Fast 8 × 8 multiply instruction
Fast 16/8 divide instruction
Binary-coded decimal (BCD) instructions
Optimization for controller applications
Efficient C language support
1.3 MCU Block Diagram
Figure 1-1 shows the structure of the MC68HC908GZ60. Refer to Appendix A.
MC68HC908GZ48 and Appendix B. MC68HC908GZ32.
Data Sheet
24
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
General Description
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
MCU Block Diagram
B
P O R T
D D R B
P O R T F
D D R F
G T P O R
D D R G
A T P O R
D D R A
C
P O R T
D D R C
P O R T E
D D R E
P O R T D
D D R D
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA General Description
Data Sheet
25
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
1.4 Pin Assignments
Figure 1-2, Figure 1-3, and Figure 1-4 illustrate the pin assignments for the 32-pin
LQFP, 48-pin LQFP, and 64-pin QFP respectively.
RST
PTE0/TxD
24
23
22
21
20
19
18
17
1
PTA2/KBD2/AD10
PTA1/KBD1/AD9
PTA0/KBD0/AD8
VSSAD/VREFL
VDDAD/VREFH
PTB5/AD5
2
3
4
5
6
7
8
PTE1/RxD
IRQ
PTD0/SS/MCLK
PTD1/MISO
PTD2/MOSI
PTD3/SPSCK
PTB4/AD4
PTB3/AD3
Figure 1-2. 32-Pin LQFP Pin Assignments
Data Sheet
26
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
General Description
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
Pin Assignments
PTA2/KBD2/AD10
36
RST
PTE0/TxD
PTE1/RxD
PTE2
1
PTA1/KBD1/AD9
PTA0/KBD0/AD8
35
34
33
32
31
30
29
28
27
26
2
3
4
5
6
7
8
9
PTC6
PTC5
PTE3
VSSAD/VREFL
VDDAD/VREFH
PTB7/AD7
PTE4
PTE5
IRQ
PTD0/SS/MCLK
PTD1/MISO
PTD2/MOSI
PTB6/AD6
PTB5/AD5
PTB4/AD4
PTB3/AD3
10
11
25
PTD3/SPSCK
12
Figure 1-3. 48-Pin LQFP Pin Assignments
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
27
MOTOROLA
General Description
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
64
49
63 62 61 60 59 58 57 56 55 54 53 52 51 50
RST
1
PTA2/KBD2/AD10
PTA1/KBD1/AD9
48
47
46
45
PTE0/TxD
PTE1/RxD
PTE2
2
3
4
5
6
7
8
9
PTA0/KBD0/AD8
PTC6
PTE3
44
43
42
41
40
39
38
37
PTC5
PTE4
PTG3/AD19
PTG2/AD18
PTG1/AD17
PTG0/AD16
VSSAD/VREFL
PTE5
PTF0
PTF1
PTF2
10
11
12
13
14
15
PTF3
VDDAD/VREFH
PTB7/AD7
PTB6/AD6
IRQ
PTD0/SS/MCLK
PTD1/MISO
36
35
34
PTB5/AD5
PTB4/AD4
PTB3/AD3
PTD2/MOSI
PTD3/SPSCK
16
33
23 24 25 26 27 28 29 30 31
18 19 20 21 22
17
32
Figure 1-4. 64-Pin QFP Pin Assignments
1.5 Pin Functions
Descriptions of the pin functions are provided here.
1.5.1 Power Supply Pins (VDD and VSS
)
VDD and VSS are the power supply and ground pins. The MCU operates from a
single power supply.
Fast signal transitions on MCU pins place high, short-duration current demands on
the power supply. To prevent noise problems, take special care to provide power
Data Sheet
28
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
General Description
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
Pin Functions
supply bypassing at the MCU as Figure 1-5 shows. Place the C1 bypass capacitor
as close to the MCU as possible. Use a high-frequency-response ceramic
capacitor for C1. C2 is an optional bulk current bypass capacitor for use in
applications that require the port pins to source high current levels.
MCU
VDD
VSS
C1
0.1 µF
+
C2
VDD
Note: Component values shown represent typical applications.
Figure 1-5. Power Supply Bypassing
1.5.2 Oscillator Pins (OSC1 and OSC2)
OSC1 and OSC2 are the connections for an external crystal, resonator, or clock
circuit. See Section 4. Clock Generator Module (CGM).
1.5.3 External Reset Pin (RST)
A low on the RST pin forces the MCU to a known startup state. RST is bidirectional,
allowing a reset of the entire system. It is driven low when any internal reset source
is asserted. This pin contains an internal pullup resistor. See Section 15. System
Integration Module (SIM).
1.5.4 External Interrupt Pin (IRQ)
IRQ is an asynchronous external interrupt pin. This pin contains an internal pullup
resistor. See Section 8. External Interrupt (IRQ).
1.5.5 CGM Power Supply Pins (VDDA and VSSA
)
VDDA and VSSA are the power supply pins for the analog portion of the clock
generator module (CGM). Decoupling of these pins should be as per the digital
supply. See Section 4. Clock Generator Module (CGM).
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
29
MOTOROLA
General Description
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
1.5.6 External Filter Capacitor Pin (CGMXFC)
CGMXFC is an external filter capacitor connection for the CGM. See Section 4.
Clock Generator Module (CGM).
1.5.7 ADC Power Supply/Reference Pins (VDDAD/VREFH and VSSAD/VREFL
)
VDDAD and VSSAD are the power supply pins to the analog-to-digital converter
(ADC). VREFH and VREFL are the reference voltage pins for the ADC. VREFH is the
high reference supply for the ADC, and by default the VDDAD/VREFH pin should be
externally filtered and connected to the same voltage potential as VDD. VREFL is the
low reference supply for the ADC, and by default the VSSAD/VREFL pin should be
connected to the same voltage potential as VSS. See Section 3. Analog-to-Digital
Converter (ADC).
1.5.8 Port A Input/Output (I/O) Pins (PTA7/KBD7/AD15–PTA0/KBD0/AD8)
PTA7–PTA0 are general-purpose, bidirectional I/O port pins. Any or all of the port
A pins can be programmed to serve as keyboard interrupt pins or used as
analog-to-digital inputs. PTA7–PTA4 are only available on the 48-pin LQFP and
64-pin QFP packages. See Section 13. Input/Output (I/O) Ports, Section 9.
Keyboard Interrupt Module (KBI), and Section 3. Analog-to-Digital Converter
(ADC).
These port pins also have selectable pullups when configured for input mode. The
pullups are disengaged when configured for output mode. The pullups are
selectable on an individual port bit basis.
1.5.9 Port B I/O Pins (PTB7/AD7–PTB0/AD0)
PTB7–PTB0 are general-purpose, bidirectional I/O port pins that can also be used
for analog-to-digital converter (ADC) inputs. PTB7–PTB6 are only available on the
48-pin LQFP and 64-pin QFP packages. See Section 13. Input/Output (I/O)
Ports and Section 3. Analog-to-Digital Converter (ADC).
1.5.10 Port C I/O Pins (PTC6–PTC0/CANTX)
PTC6 and PTC5 are general-purpose, bidirectional I/O port pins.
PTC4–PTC0 are general-purpose, bidirectional I/O port pins that contain higher
current sink/source capability. PTC6–PTC2 are only available on the 48-pin LQFP
and 64-pin QFP packages. See Section 13. Input/Output (I/O) Ports.
PTC1 and PTC0 can be programmed to be MSCAN08 pins.
These port pins also have selectable pullups when configured for input mode. The
pullups are disengaged when configured for output mode. The pullups are
selectable on an individual port bit basis.
Data Sheet
30
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
General Description
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
Pin Functions
1.5.11 Port D I/O Pins (PTD7/T2CH1–PTD0/SS)
PTD7–PTD0 are special-function, bidirectional I/O port pins. PTD3–PTD0 can be
programmed to be serial peripheral interface (SPI) pins, while PTD7–PTD4 can be
individually programmed to be timer interface module (TIM1 and TIM2) pins. PTD0
can be used to output a clock, MCLK. PTD7 is only available on the 48-pin LQFP
and 64-pin QFP packages. See Section 18. Timer Interface Module (TIM1),
Section 19. Timer Interface Module (TIM2), Section 16. Serial Peripheral
Interface (SPI) Module, Section 13. Input/Output (I/O) Ports. and Section 5.
Configuration Register (CONFIG).
These port pins also have selectable pullups when configured for input mode. The
pullups are disengaged when configured for output mode. The pullups are
selectable on an individual port bit basis.
1.5.12 Port E I/O Pins (PTE5–PTE2, PTE1/RxD, and PTE0/TxD)
PTE5–PTE0 are general-purpose, bidirectional I/O port pins. PTE1 and PTE0 can
also be programmed to be enhanced serial communications interface (ESCI) pins.
PTE5–PTE2 are only available on the 48-pin LQFP and 64-pin QFP packages. See
Section 14. Enhanced Serial Communications Interface (ESCI) Module and
Section 13. Input/Output (I/O) Ports.
1.5.13 Port F I/O Pins (PTF7/T2CH5–PTF0)
PTF7–PTF4 are special-function, bidirectional I/O port pins that can be individually
programmed to be timer interface module (TIM2) pins.
PTF3–PTF0 are general-purpose, bidirectional I/O port pins that contain higher
current sink/source capability.
PTF7–PTF0 are only available on the 64-pin QFP package. See Section 18.
Timer Interface Module (TIM1), Section 19. Timer Interface Module (TIM2), and
Section 13. Input/Output (I/O) Ports.
1.5.14 Port G I/O Pins (PTG7/AD23–PTBG0/AD16)
PTG7–PTG0 are general-purpose, bidirectional I/O port pins that can also be used
for analog-to-digital converter (ADC) inputs. PTG7–PTG0 are only available on the
64-pin QFP package. See Section 13. Input/Output (I/O) Ports and Section 3.
Analog-to-Digital Converter (ADC).
NOTE:
Any unused inputs and I/O ports should be tied to an appropriate logic level (either
VDD or VSS). Although the I/O ports do not require termination, termination is
recommended to reduce the possibility of static damage.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
31
MOTOROLA
General Description
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
General Description
Data Sheet
32
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
General Description
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 2. Memory
2.1 Introduction
The CPU08 can address 64 Kbytes of memory space. The memory map, shown in
Figure 2-1, includes:
•
•
•
62,078 bytes of user FLASH memory
2048 bytes of random-access memory (RAM)
52 bytes of user-defined vectors
2.2 Unimplemented Memory Locations
Accessing an unimplemented location can cause an illegal address reset. In the
memory map (Figure 2-1) and in register figures in this document, unimplemented
locations are shaded.
2.3 Reserved Memory Locations
Accessing a reserved location can have unpredictable effects on microcontroller
(MCU) operation. In the Figure 2-1 and in register figures in this document,
reserved locations are marked with the word Reserved or with the letter R.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
33
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
$FE00
$FE01
$FE02
$FE03
$FE04
$FE05
$FE06
$FE07
$FE08
$FE09
$FE0A
$FE0B
$FE0C
$FE0D
$FE0E
$FE0F
SIM BREAK STATUS REGISTER (BSR)
$0000
↓
$003F
I/O REGISTERS
64 BYTES
SIM RESET STATUS REGISTER (SRSR)
RESERVED
SIM BREAK FLAG CONTROL REGISTER (BFCR)
INTERRUPT STATUS REGISTER 1 (INT1)
INTERRUPT STATUS REGISTER 2 (INT2)
INTERRUPT STATUS REGISTER 3 (INT3)
INTERRUPT STATUS REGISTER 4 (INT4)
FLASH-2 CONTROL REGISTER (FL2CR)
BREAK ADDRESS REGISTER HIGH (BRKH)
BREAK ADDRESS REGISTER LOW (BRKL)
BREAK STATUS AND CONTROL REGISTER (BRKSCR)
LVI STATUS REGISTER (LVISR)
$0040
↓
$043F
RAM-1
1024 BYTES
$0440
↓
$0461
I/O REGISTERS
34 BYTES
$0462
↓
$04FF
FLASH-2
158 BYTES
$0500
↓
$057F
MSCAN CONTROL AND MESSAGE BUFFER
128 BYTES
FLASH-2 TEST CONTROL REGISTER (FLTCR2)
FLASH-1 TEST CONTROL REGISTER (FLTCR1)
UNIMPLEMENTED
$0580
↓
$097F
RAM-2
1024 BYTES
UNIMPLEMENTED
16 BYTES
$FE10
↓
$FE1F
RESERVED FOR COMPATIBILITY WITH MONITOR CODE
FOR A-FAMILY PART
$0980
↓
$1B7F
FLASH-2
4608 BYTES
$FE20
↓
$FF7F
MONITOR ROM
352 BYTES
$1B80
↓
$1DFF
RESERVED
640 BYTES
$FF80
$FF81
FLASH-1 BLOCK PROTECT REGISTER (FL1BPR)
FLASH-2 BLOCK PROTECT REGISTER (FL2BPR)
$1E00
↓
$1E0F
MONITOR ROM
16 BYTES
$FF82
↓
$FF87
RESERVED
6 BYTES
$1E10
↓
$1E1F
RESERVED
16 BYTES
$FF88
FLASH-1 CONTROL REGISTER (FL1CR)
$1E20
↓
$7FFF
$FF89
↓
$FFCB
FLASH-2
25,056 BYTES
RESERVED
67 BYTES
$8000
↓
$FDFF
$FFCC
↓
$FFFF(1)
FLASH-1
32,256 BYTES
FLASH-1 VECTORS
52 BYTES
1. $FFF6–$FFFD used for eight security bytes
Figure 2-1. MC68HC908GZ60 Memory Map
Data Sheet
34
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Input/Output (I/O) Section
2.4 Input/Output (I/O) Section
Most of the control, status, and data registers are in the zero page area of
$0000–$003F, or at $0440–$0461. Additional I/O registers have these addresses:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
$FE00; SIM break status register, BSR
$FE01; SIM reset status register, SRSR
$FE02; reserved
$FE03; SIM break flag control register, BFCR
$FE04; interrupt status register 1, INT1
$FE05; interrupt status register 2, INT2
$FE06; interrupt status register 3, INT3
$FE07; interrupt status register 4, INT4
$FE08; FLASH-2 control register, FL2CR
$FE09; break address register high, BRKH
$FE0A; break address register low, BRKL
$FE0B; break status and control register, BRKSCR
$FE0C; LVI status register, LVISR
$FE0D; FLASH-2 test control register, FLTCR2
$FE0E; FLASH-1 test control register, FLTCR1
$FF80; FLASH-1 block protect register, FL1BPR
$FF81; FLASH-2 block protect register, FL2BPR
$FF88; FLASH-1 control register, FL1CR
Data registers are shown in Figure 2-2. Table 2-1 is a list of vector locations.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
35
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Port A Data Register
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
$0000
(PTA) Write:
See page 187.
Reset:
Read:
Unaffected by reset
PTB4 PTB3
Unaffected by reset
PTC4 PTC3
Unaffected by reset
PTD4 PTD3
Unaffected by reset
Port B Data Register
PTB7
1
PTB6
PTC6
PTD6
PTB5
PTC5
PTD5
PTB2
PTC2
PTD2
PTB1
PTC1
PTD1
PTB0
PTC0
PTD0
$0001
$0002
$0003
$0004
$0005
$0006
$0007
$0008
$0009
(PTB) Write:
See page 190.
Reset:
Read:
Port C Data Register
(PTC) Write:
See page 192.
Reset:
Read:
Port D Data Register
PTD7
(PTD) Write:
See page 194.
Reset:
Read:
Data Direction Register A
DDRA7
0
DDRA6
0
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
(DDRA) Write:
See page 188.
Reset:
Read:
0
DDRB5
0
0
DDRB4
0
0
DDRB3
0
0
DDRB2
0
0
DDRB1
0
0
DDRB0
0
Data Direction Register B
DDRB7
DDRB6
0
(DDRB) Write:
See page 190.
Reset:
Read:
0
0
Data Direction Register C
DDRC6
0
DDRC5
0
DDRC4
0
DDRC3
0
DDRC2
0
DDRC1
0
DDRC0
0
(DDRC) Write:
See page 192.
Reset:
Read:
0
Data Direction Register D
DDRD7
DDRD6
DDRD5
0
DDRD4
0
DDRD3
0
DDRD2
0
DDRD1
0
DDRD0
0
(DDRD) Write:
See page 196.
Reset:
Read:
0
0
0
0
Port E Data Register
PTE5
PTE4
PTE3
PTE2
PTE1
PTE0
(PTE) Write:
See page 198.
Reset:
Read:
Unaffected by reset
ESCI Prescaler Register
PDS2
0
PDS1
0
PDS0
0
PSSB4
PSSB3
0
PSSB2
PSSB1
0
PSSB0
0
(SCPSC) Write:
See page 234.
Reset:
0
0
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 1 of 10)
Data Sheet
36
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Input/Output (I/O) Section
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Read:
ESCI Arbiter Control
Register (SCIACTL) Write:
ALOST
AFIN
ARUN
AROVFL
ARD8
AM1
AM0
ACLK
$000A
See page 237.
Reset:
0
0
0
0
0
0
0
0
Read:
ESCI Arbiter Data
Register (SCIADAT) Write:
ARD7
ARD6
ARD5
ARD4
ARD3
ARD2
ARD1
ARD0
$000B
$000C
$000D
$000E
$000F
$0010
$0011
$0012
$0013
See page 238.
Reset:
0
0
0
0
0
DDRE5
0
0
DDRE4
0
0
DDRE3
0
0
DDRE2
0
0
DDRE1
0
0
DDRE0
0
Read:
Data Direction Register E
(DDRE) Write:
See page 199.
Reset:
0
0
Read:
Port A Input Pullup Enable
PTAPUE7 PTAPUE6 PTAPUE5 PTAPUE4 PTAPUE3 PTAPUE2 PTAPUE1 PTAPUE0
Register (PTAPUE) Write:
See page 189.
Reset:
0
0
0
0
0
0
0
0
0
Read:
Port C Input Pullup Enable
PTCPUE6 PTCPUE5 PTCPUE4 PTCPUE3 PTCPUE2 PTCPUE1 PTCPUE0
Register (PTCPUE) Write:
See page 194.
Reset:
0
0
0
0
0
0
0
0
Read:
Port D Input Pullup Enable
PTDPUE7 PTDPUE6 PTDPUE5 PTDPUE4 PTDPUE3 PTDPUE2 PTDPUE1 PTDPUE0
Register (PTDPUE) Write:
See page 197.
Reset:
0
0
0
0
0
0
0
SPE
0
0
Read:
SPI Control Register
SPRIE
R
0
SPMSTR
CPOL
CPHA
SPWOM
0
SPTIE
0
(SPCR) Write:
See page 279.
Reset:
0
1
0
1
Read:
SPI Status and Control
Register (SPSCR) Write:
SPRF
OVRF
MODF
SPTE
ERRIE
MODFEN
SPR1
SPR0
See page 281.
Reset:
0
0
0
0
1
0
0
0
Read:
R7
T7
R6
T6
R5
T5
R4
T4
R3
T3
R2
T2
R1
T1
R0
T0
SPI Data Register
(SPDR) Write:
See page 283.
Reset:
Unaffected by reset
Read:
ESCI Control Register 1
LOOPS
0
ENSCI
0
TXINV
0
M
WAKE
0
ILTY
PEN
0
PTY
0
(SCC1) Write:
See page 223.
Reset:
0
0
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 2 of 10)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
37
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Addr.
Register Name
Bit 7
6
TCIE
0
5
4
ILIE
0
3
TE
2
RE
0
1
Bit 0
SBK
0
Read:
ESCI Control Register 2
SCTIE
SCRIE
RWU
0
$0014
(SCC2) Write:
See page 225.
Reset:
Read:
0
0
0
R8
ESCI Control Register 3
T8
R
R
ORIE
NEIE
FEIE
PEIE
$0015
$0016
$0017
$0018
$0019
(SCC3) Write:
See page 227.
Reset:
Read:
U
0
0
0
0
0
0
0
SCTE
TC
SCRF
IDLE
OR
NF
FE
PE
ESCI Status Register 1
(SCS1) Write:
See page 228.
Reset:
Read:
1
0
1
0
0
0
0
0
0
0
0
0
0
0
BKF
RPF
ESCI Status Register 2
(SCS2) Write:
See page 231.
Reset:
Read:
0
0
0
0
0
0
0
0
R7
T7
R6
T6
R5
T5
R4
T4
R3
T3
R2
T2
R1
T1
R0
T0
ESCI Data Register
(SCDR) Write:
See page 231.
Reset:
Read:
Unaffected by reset
ESCI Baud Rate Register
LINT
LINR
SCP1
SCP0
R
SCR2
SCR1
SCR0
(SCBR) Write:
See page 232.
Reset:
Read:
0
0
0
0
0
0
0
0
0
0
0
0
KEYF
0
ACKK
0
Keyboard Status and Control
IMASKK
MODEK
$001A
$001B
$001C
$001D
Register (INTKBSCR) Write:
See page 130.
Reset:
0
0
0
0
0
0
KBIE1
0
0
Read:
Keyboard Interrupt Enable
Register (INTKBIER) Write:
KBIE7
KBIE6
0
KBIE5
0
KBIE4
0
KBIE3
KBIE2
0
KBIE0
See page 131.
Reset:
0
0
0
0
Read:
TBIF
Timebase Module Control
TBR2
TBR1
TBR0
TBIE
TBON
0
R
Register (TBCR) Write:
See page 288.
Reset:
TACK
0
0
0
0
0
0
0
0
0
0
0
MODE
0
Read:
IRQ Status and Control
Register (INTSCR) Write:
IRQF
0
IMASK
0
ACK
See page 124.
Reset:
0
0
0
0
0
0
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 3 of 10)
Data Sheet
38
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Input/Output (I/O) Section
Addr.
Register Name
Bit 7
6
MCLKSEL
0
5
MCLK1
0
4
MCLK0
0
3
2
1
Bit 0
Read:
Write:
Reset:
Read:
0
Configuration Register 2
(CONFIG2)(1)
See page 100.
MSCAN- TBMCLK- OSCENIN-
EN(1)
SCIBDSRC
SEL
STOP
$001E
0
COPRS
0
0
0
0
1
COPD
0
LVISTOP LVIRSTD LVIPWRD LVI5OR3(1) SSREC
STOP
0
Configuration Register 1
$001F
(CONFIG1)(1) Write:
See page 101.
Reset:
0
0
0
0
0
1. One-time writable register after each reset, except MSCANEN and LVI5OR3 bits. MSCANEN andLVI5OR3 bits are only
reset via POR (power-on reset).
Read:
TOF
0
0
TRST
0
0
TIM1 Status and Control
TOIE
TSTOP
PS2
PS1
PS0
$0020
$0021
$0022
$0023
$0024
$0025
$0026
$0027
Register (T1SC) Write:
See page 301.
Reset:
0
0
1
0
0
0
9
0
Read:
TIM1 Counter
Register High (T1CNTH) Write:
Bit 15
14
13
12
11
10
Bit 8
See page 302.
Reset:
0
0
6
0
5
0
4
0
3
0
2
0
1
0
Read:
TIM1 Counter
Register Low (T1CNTL) Write:
Bit 7
Bit 0
See page 302.
Reset:
0
Bit 15
1
0
0
0
0
0
0
0
Read:
TIM1 Counter Modulo
Register High (T1MODH) Write:
14
13
12
11
10
9
Bit 8
See page 303.
Reset:
1
1
1
1
1
1
1
Bit 0
1
Read:
TIM1 Counter Modulo
Register Low (T1MODL) Write:
Bit 7
6
1
5
1
4
1
3
2
1
See page 303.
Reset:
1
CH0F
0
1
ELS0B
0
1
ELS0A
0
1
TOV0
0
Read:
TIM1 Channel 0 Status and
Control Register (T1SC0) Write:
CH0IE
0
MS0B
0
MS0A
0
CH0MAX
0
See page 304.
Reset:
0
Read:
TIM1 Channel 0
Register High (T1CH0H) Write:
Bit 15
Bit 7
14
13
12
11
10
9
Bit 8
See page 307.
Reset:
Indeterminate after reset
Read:
TIM1 Channel 0
Register Low (T1CH0L) Write:
6
5
4
3
2
1
Bit 0
See page 307.
Reset:
Indeterminate after reset
R = Reserved
= Unimplemented
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 4 of 10)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
39
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Addr.
Register Name
TIM1 Channel 1 Status and
Control Register (T1SC1) Write:
Bit 7
CH1F
0
6
CH1IE
0
5
4
MS1A
0
3
ELS1B
0
2
ELS1A
0
1
TOV1
0
Bit 0
CH1MAX
0
Read:
0
$0028
$0029
$002A
$002B
$002C
$002D
$002E
$002F
$0030
$0031
See page 304.
Reset:
0
0
Read:
TIM1 Channel 1
Register High (T1CH1H) Write:
Bit 15
Bit 7
14
13
12
11
10
9
Bit 8
See page 307.
Reset:
Indeterminate after reset
Read:
TIM1 Channel 1
Register Low (T1CH1L) Write:
6
5
4
3
2
1
Bit 0
PS0
See page 307.
Reset:
Indeterminate after reset
Read:
TOF
0
0
TRST
0
0
TIM2 Status and Control
TOIE
TSTOP
PS2
PS1
Register (T2SC) Write:
See page 323.
Reset:
0
0
1
0
0
0
9
0
Read:
TIM2 Counter
Register High (T2CNTH) Write:
Bit 15
14
13
12
11
10
Bit 8
See page 325.
Reset:
0
0
6
0
5
0
4
0
3
0
2
0
1
0
Read:
TIM2 Counter
Register Low (T2CNTL) Write:
Bit 7
Bit 0
See page 325.
Reset:
0
Bit 15
1
0
0
0
0
0
0
0
Read:
TIM2 Counter Modulo
Register High (T2MODH) Write:
14
13
12
11
10
9
Bit 8
See page 325.
Reset:
1
1
1
1
1
1
1
Bit 0
1
Read:
TIM2 Counter Modulo
Register Low (T2MODL) Write:
Bit 7
6
1
5
1
4
1
3
2
1
See page 325.
Reset:
1
CH0F
0
1
ELS0B
0
1
ELS0A
0
1
TOV0
0
Read:
TIM2 Channel 0 Status and
Control Register (T2SC0) Write:
CH0IE
0
MS0B
0
MS0A
0
CH0MAX
0
See page 326.
Reset:
0
Read:
TIM2 Channel 0
Register High (T2CH0H) Write:
Bit 15
14
13
12
11
10
9
Bit 8
See page 330.
Reset:
Indeterminate after reset
R = Reserved
= Unimplemented
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 5 of 10)
Data Sheet
40
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Input/Output (I/O) Section
Addr.
Register Name
TIM2 Channel 0
Register Low (T2CH0L) Write:
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Bit 7
6
5
4
3
2
1
Bit 0
$0032
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 1 Status and
Control Register (T2SC1) Write:
CH1F
0
CH1IE
MS1A
0
ELS1B
ELS1A
TOV1
CH1MAX
$0033
$0034
$0035
$0036
$0037
$0038
$0039
$003A
$003B
0
0
See page 326.
Reset:
0
0
0
0
0
9
0
Read:
TIM2 Channel 1
Register High (T2CH1H) Write:
Bit 15
14
13
12
11
10
Bit 8
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 1
Register Low (T2CH1L) Write:
Bit 7
6
5
4
3
2
1
Bit 0
See page 330.
Reset:
Indeterminate after reset
Read:
PLLF
PLL Control Register
PLLIE
0
PLLON
1
BCS
R
R
VPR1
VPR0
(PCTL) Write:
See page 90.
Reset:
0
0
0
0
0
0
0
0
0
0
Read:
LOCK
PLL Bandwidth Control
AUTO
ACQ
R
Register (PBWC) Write:
See page 92.
Reset:
0
0
0
0
0
0
0
0
0
0
0
0
Read:
PLL Multiplier Select High
MUL11
MUL10
MUL9
MUL8
Register (PMSH) Write:
See page 93.
Reset:
0
0
0
0
0
0
MUL2
0
0
0
Read:
PLL Multiplier Select Low
MUL7
0
MUL6
1
MUL5
0
MUL4
0
MUL3
MUL1
MUL0
Register (PMSL) Write:
See page 94.
Reset:
0
0
0
Read:
PLL VCO Select Range
VRS7
VRS6
VRS5
VRS4
VRS3
VRS2
0
VRS1
VRS0
Register (PMRS) Write:
See page 94.
Reset:
0
0
1
0
0
0
0
0
0
R
0
0
R
0
0
R
1
Read:
Reserved Write:
Reset:
R
0
0
0
0
0
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 6 of 10)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
41
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Read: COCO
ADC Status and Control
Register (ADSCR) Write:
AIEN
ADCO
ADCH4
ADCH3
ADCH2
ADCH1
ADCH0
$003C
R
0
See page 72.
Reset:
0
0
0
0
1
0
1
0
1
0
1
1
Read:
0
AD9
AD8
ADC Data High Register
$003D
$003E
$003F
$0440
$0441
$0444
$0445
$0448
(ADRH) Write:
See page 74.
Reset:
Unaffected by reset
AD4 A3
Read:
AD7
AD6
AD5
AD2
AD1
AD0
ADC Data Low Register
(ADRL) Write:
See page 74.
Reset:
Unaffected by reset
Read:
0
ADC Clock Register
ADIV2
0
ADIV1
0
ADIV0
0
ADICLK
0
MODE1
0
MODE0
1
R
0
(ADCLK) Write:
See page 76.
Reset:
0
Read:
Port F Data Register
PTF7
PTF6
PTF5
PTF4
PTAF3
PTF2
PTF1
PTF0
(PTF) Write:
See page 200.
Reset:
Unaffected by reset
PTG4 PTG3
Unaffected by reset
Read:
Port G Data Register
PTG7
PTG6
PTG5
PTG2
PTG1
PTG0
(PTG) Write:
See page 202.
Reset:
Read:
Data Direction Register F
DDRF7
0
DDRF6
DDRF5
DDRF4
0
DDRF3
DDRF2
0
DDRF1
DDRF0
(DDRF) Write:
See page 200.
Reset:
0
DDRG6
0
0
DDRG5
0
0
DDRG3
0
0
DDRG1
0
0
Read:
Data Direction Register G
DDRG7
0
DDRG4
0
DDRG2
0
DDRG0
(DDRG) Write:
See page 202.
Reset:
0
Read:
Write:
Reset:
Read:
Keyboard Interrupt
Polarity Register
(INTKBIPR)
KBIP7
KBIP6
0
KBIP5
0
KBIP4
0
KBIP3
0
KBIP2
0
KBIP1
0
KBIP0
See page 132.
0
CH2F
0
0
CH2MAX
0
TIM2 Channel 2 Status and
CH2IE
0
MS2B
0
MS2A
ELS2B
0
ELS2A
TOV2
0
$0456
Control Register (T2SC2) Write:
See page 330.
Reset:
0
0
0
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 7 of 10)
Data Sheet
42
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Input/Output (I/O) Section
Addr.
Register Name
TIM2 Channel 2
Register High (T2CH2H) Write:
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Bit 15
14
13
12
11
10
9
Bit 8
$0457
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 2
Register Low (T2CH2L) Write:
Bit 7
6
5
0
4
3
2
1
Bit 0
$0458
$0459
$045A
$045B
$045C
$045D
$045E
$045F
$0460
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 3 Status and
Control Register (T2SC3) Write:
CH3F
CH3IE
MS3A
0
ELS3B
ELS3A
TOV3
CH3MAX
0
0
See page 326.
Reset:
0
0
0
0
0
9
0
Read:
TIM2 Channel 3
Register High (T2CH3H) Write:
Bit 15
14
13
12
11
10
Bit 8
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 3
Register Low (T2CH3L) Write:
Bit 7
6
5
4
3
2
1
Bit 0
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 4 Status and
Control Register (T2SC4) Write:
CH4F
CH4IE
MS4B
0
MS4A
0
ELS4B
ELS4A
TOV4
CH4MAX
0
0
See page 326.
Reset:
0
0
0
0
9
0
Read:
TIM2 Channel 4
Register High (T2CH4H) Write:
Bit 15
14
13
12
11
10
Bit 8
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 4
Register Low (T2CH4L) Write:
Bit 7
6
5
0
4
3
2
1
Bit 0
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 5 Status and
Control Register (T2SC5) Write:
CH5F
CH5IE
MS5A
0
ELS5B
ELS5A
TOV 5
CH5MAX
0
0
See page 326.
Reset:
0
0
0
0
0
9
0
Read:
TIM2 Channel 5
Register High (T2CH5H) Write:
Bit 15
14
13
12
11
10
Bit 8
See page 330.
Reset:
Indeterminate after reset
R = Reserved
= Unimplemented
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 8 of 10)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
43
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Addr.
Register Name
TIM2 Channel 5
Register Low (T2CH5L) Write:
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Bit 7
6
5
4
3
2
1
Bit 0
$0461
See page 330.
Reset:
Indeterminate after reset
Read:
SBSW
NOTE 1
0
Break Status Register
R
0
R
0
R
0
R
0
R
0
R
0
R
0
$FE00
(BSR) Write:
See page 258.
Reset:
1. Writing a 0 clears SBSW.
Read:
POR
PIN
COP
ILOP
ILAD
MODRST
LVI
0
SIM Reset Status Register
$FE01
$FE02
$FE03
$FE04
$FE05
$FE06
$FE07
$FE08
(SRSR) Write:
See page 259.
POR:
Read:
1
R
0
R
0
0
R
0
0
R
0
0
R
0
0
R
0
0
R
0
0
R
0
Reserved Write:
Reset:
0
Read:
Break Flag Control Register
BCFE
R
R
R
R
R
R
R
(BFCR) Write:
See page 260.
Reset:
Read:
0
IF6
R
0
IF5
R
0
IF4
R
0
IF3
R
0
IF2
R
0
IF1
R
0
0
0
0
Interrupt Status Register 1
(INT1) Write:
R
R
See page 254.
Reset:
Read:
0
0
0
0
0
0
0
0
IF14
R
IF13
R
IF12
R
IF11
R
IF10
R
IF9
R
IF8
R
IF7
R
Interrupt Status Register 2
(INT2) Write:
See page 254.
Reset:
Read:
0
0
0
0
0
0
0
0
IF22
R
IF21
R
IF20
R
IF19
R
IF18
R
IF17
R
IF16
R
IF15
R
Interrupt Status Register 3
(INT3) Write:
See page 254.
Reset:
Read:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
IF24
R
IF23
R
Interrupt Status Register 4
(INT4) Write:
R
R
R
R
R
R
See page 255.
Reset:
Read:
0
0
0
0
0
0
0
0
0
0
0
0
FLASH-2 Control Register
HVEN
0
MASS
ERASE
0
PGM
0
(FL2CR) Write:
See page 57.
Reset:
0
0
0
0
0
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 9 of 10)
Data Sheet
44
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Input/Output (I/O) Section
Addr.
Register Name
Bit 7
Bit 15
0
6
5
13
0
4
12
0
3
11
0
2
10
0
1
9
0
1
Bit 0
Bit 8
0
Read:
Break Address Register High
14
$FE09
(BRKH) Write:
See page 338.
Reset:
Read:
0
Break Address Register Low
Bit 7
0
6
0
5
4
3
2
Bit 0
$FE0A
$FE0B
$FE0C
$FE0D
$FE0E
$FF80
$FF81
(BRKL) Write:
See page 338.
Reset:
Read:
0
0
0
0
0
0
0
0
0
0
0
0
Break Status and Control
BRKE
0
BRKA
Register (BRKSCR) Write:
See page 337.
Reset:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Read: LVIOUT
LVI Status Register
(LVISR) Write:
See page 143.
Reset:
Read:
Write:
Reset:
Read:
Write:
Reset:
Read:
Write:
Reset:
Read:
Write:
Reset:
0
0
0
0
0
0
0
0
R
R
R
R
R
R
R
R
FLASH-2 Test Control
Register (FLTCR2)
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
FLASH-1 Test Control
Register (FLTCR1)
0
0
0
0
0
0
0
0
FLASH-1 Block Protect
(1)
Register (FL1BPR)
BPR7
BPR6
BPR5
BPR4
BPR3
BPR2
BPR1
BPR0
See page 50.
Unaffected by reset
BPR4 BPR3
FLASH-2 Block Protect
(1)
Register (FL2BPR)
BPR7
BPR6
BPR5
BPR2
BPR1
BPR0
See page 58.
Unaffected by reset
1. Non-volatile FLASH register
Read:
0
0
0
0
0
0
0
FLASH-1 Control Register
HVEN
MASS
0
ERASE
0
PGM
0
$FF88
(FL1CR) Write:
See page 49.
Reset:
0
0
Read:
Low byte of reset vector
COP Control Register
(COPCTL) Write:
See page 105.
$FFFF
Writing clears COP counter (any value)
Unaffected by reset
Reset:
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 10 of 10)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
45
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
.
Table 2-1. Vector Addresses
Vector Priority
Vector
Address
$FFCC
$FFCD
$FFCE
$FFCF
$FFD0
$FFD1
$FFD2
$FFD3
$FFD4
$FFD5
$FFD6
$FFD7
$FFD8
$FFD9
$FFDA
$FFDB
$FFDC
$FFDD
$FFDE
$FFDF
$FFE0
$FFE1
$FFE2
$FFE3
$FFE4
$FFE5
$FFE6
$FFE7
$FFE8
$FFE9
$FFEA
$FFEB
$FFEC
$FFED
Vector
TIM2 Channel 5 Vector (High)
TIM2 Channel 5 Vector (Low)
TIM2 Channel 4 Vector (High)
TIM2 Channel 4 Vector (Low)
TIM2 Channel 3 Vector (High)
TIM2 Channel 3 Vector (Low)
TIM2 Channel 2 Vector (High)
TIM2 Channel 2 Vector (Low)
MSCAN08 Transmit Vector (High)
MSCAN08 Transmit Vector (Low)
MSCAN08 Receive Vector (High)
MSCAN08 Receive Vector (Low)
MSCAN08 Error Vector (High)
MSCAN08 Error Vector (Low)
MSCAN08 Wakeup Vector (High)
MSCAN08 Wakeup Vector (Low)
Timebase Vector (High)
Lowest
IF24
IF23
IF22
IF21
IF20
IF19
IF18
IF17
IF16
IF15
IF14
IF13
IF12
IF11
IF10
IF9
Timebase Vector (Low)
ADC Conversion Complete Vector (High)
ADC Conversion Complete Vector (Low)
Keyboard Vector (High)
Keyboard Vector (Low)
ESCI Transmit Vector (High)
ESCI Transmit Vector (Low)
ESCI Receive Vector (High)
ESCI Receive Vector (Low)
ESCI Error Vector (High)
ESCI Error Vector (Low)
SPI Transmit Vector (High)
SPI Transmit Vector (Low)
SPI Receive Vector (High)
SPI Receive Vector (Low)
TIM2 Overflow Vector (High)
TIM2 Overflow Vector (Low)
IF8
Data Sheet
46
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Random-Access Memory (RAM)
Table 2-1. Vector Addresses (Continued)
Vector Priority
Vector
Address
$FFEE
$FFEF
$FFF0
$FFF1
$FFF2
$FFF3
$FFF4
$FFF5
$FFF6
$FFF7
$FFF8
$FFF9
$FFFA
$FFFB
$FFFC
$FFFD
$FFFE
$FFFF
Vector
TIM2 Channel 1 Vector (High)
TIM2 Channel 1 Vector (Low)
TIM2 Channel 0 Vector (High)
TIM2 Channel 0 Vector (Low)
TIM1 Overflow Vector (High)
TIM1 Overflow Vector (Low)
TIM1 Channel 1 Vector (High)
TIM1 Channel 1 Vector (Low)
TIM1 Channel 0 Vector (High)
TIM1 Channel 0 Vector (Low)
PLL Vector (High)
IF7
IF6
IF5
IF4
IF3
IF2
IF1
—
PLL Vector (Low)
IRQ Vector (High)
IRQ Vector (Low)
SWI Vector (High)
SWI Vector (Low)
Reset Vector (High)
—
Highest
Reset Vector (Low)
2.5 Random-Access Memory (RAM)
The RAM locations are broken into two non-continuous memory blocks. The RAM
addresses locations are $0040–$043F and $0580–$097F. The location of the
stack RAM is programmable. The 16-bit stack pointer allows the stack to be
anywhere in the 64-Kbyte memory space.
NOTE:
For correct operation, the stack pointer must point only to RAM locations.
Within page zero are 192 bytes of RAM. Because the location of the stack RAM is
programmable, all page zero RAM locations can be used for I/O control and user
data or code. When the stack pointer is moved from its reset location at $00FF out
of page zero, direct addressing mode instructions can efficiently access all page
zero RAM locations. Page zero RAM, therefore, provides ideal locations for
frequently accessed global variables.
Before processing an interrupt, the CPU uses five bytes of the stack to save the
contents of the CPU registers.
NOTE:
For M6805 compatibility, the H register is not stacked.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
47
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
During a subroutine call, the CPU uses two bytes of the stack to store the return
address. The stack pointer decrements during pushes and increments during pulls.
NOTE:
Be careful when using nested subroutines. The CPU may overwrite data in the
RAM during a subroutine or during the interrupt stacking operation.
2.6 FLASH-1 Memory (FLASH-1)
This subsection describes the operation of the embedded FLASH-1 memory. This
memory can be read, programmed, and erased from a single external supply. The
program and erase operations are enabled through the use of an internal charge
pump.
2.6.1 Functional Description
The FLASH-1 memory is an array of 32,256 bytes with two bytes of block protection
(one byte for protecting areas within FLASH-1 array and one byte for protecting
areas within FLASH-2 array) and an additional 52 bytes of user vectors. An erased
bit reads as a 1 and a programmed bit reads as a 0.
Memory in the FLASH-1 array is organized into rows within pages. There are two
rows of memory per page with 64 bytes per row. The minimum erase block size is
a single page,128 bytes. Programming is performed on a per-row basis, 64 bytes
at a time. Program and erase operations are facilitated through control bits in the
FLASH-1 control register (FL1CR). Details for these operations appear later in this
subsection.
The FLASH-1 memory map consists of:
•
•
•
•
•
$8000–$FDFF: user memory (32,256 bytes)
$FF80: FLASH-1 block protect register (FL1BPR)
$FF81: FLASH-2 block protect register (FL2BPR)
$FF88: FLASH-1 control register (FL1CR)
$FFCC–$FFFF: these locations are reserved for user-defined interrupt and
reset vectors (see Table 2-1 for details)
Programming tools are available from Motorola. Contact your local Motorola
representative for more information.
NOTE:
A security feature prevents viewing of the FLASH contents.(1)
1. No security feature is absolutely secure. However, Motorola’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
Data Sheet
48
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
FLASH-1 Memory (FLASH-1)
2.6.2 FLASH-1 Control and Block Protect Registers
The FLASH-1 array has two registers that control its operation, the FLASH-1
control register (FL1CR) and the FLASH-1 block protect register (FL1BPR).
2.6.2.1 FLASH-1 Control Register
The FLASH-1 control register (FL1CR) controls FLASH program and erase
operations.
Address:
$FF88
Bit 7
0
6
0
5
0
4
0
3
HVEN
0
2
MASS
0
1
ERASE
0
Bit 0
PGM
0
Read:
Write:
Reset:
0
0
0
0
= Unimplemented
Figure 2-3. FLASH-1 Control Register (FL1CR)
HVEN — High-Voltage Enable Bit
This read/write bit enables the charge pump to drive high voltages for program
and erase operations in the array. HVEN can only be set if either PGM = 1 or
ERASE = 1 and the proper sequence for program or erase is followed.
1 = High voltage enabled to array and charge pump on
0 = High voltage disabled to array and charge pump off
MASS — Mass Erase Control Bit
Setting this read/write bit configures the FLASH-1 array for mass erase
operation.
1 = MASS erase operation selected
0 = MASS erase operation unselected
ERASE — Erase Control Bit
This read/write bit configures the memory for erase operation. ERASE is
interlocked with the PGM bit such that both bits cannot be equal to 1 or set to 1
at the same time.
1 = Erase operation selected
0 = Erase operation unselected
PGM — Program Control Bit
This read/write bit configures the memory for program operation. PGM is
interlocked with the ERASE bit such that both bits cannot be equal to 1 or set
to 1 at the same time.
1 = Program operation selected
0 = Program operation unselected
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
49
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
2.6.2.2 FLASH-1 Block Protect Register
The FLASH-1 block protect register (FL1BPR) is implemented as a byte within the
FLASH-1 memory; therefore, it can only be written during a FLASH programming
sequence. The value in this register determines the starting location of the
protected range within the FLASH-1 memory.
Address: $FF80
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
BPR7
BPR6
BPR5
BPR4
BPR3
BPR2
BPR1
BPR0
Unaffected by reset
Figure 2-4. FLASH-1 Block Protect Register (FL1BPR)
FL1BPR[7:0] — Block Protect Register Bits 7 to 0
These eight bits represent bits [14:7] of a 16-bit memory address. Bit 15 is a 1
and bits [6:0] are 0s.
The resultant 16-bit address is used for specifying the start address of the
FLASH-1 memory for block protection. FLASH-1 is protected from this start
address to the end of FLASH-1 memory at $FFFF. With this mechanism, the
protect start address can be $XX00 and $XX80 (128 byte page boundaries)
within the FLASH-1 array.
16-BIT MEMORY ADDRESS
START ADDRESS OF FLASH
BLOCK PROTECT
0
0
0
0
0
0
0
FLBPR VALUE
1
Figure 2-5. FLASH-1 Block Protect Start Address
Table 2-2. FLASH-1 Protected Ranges
FL1BPR[7:0]
$FF
Protected Range
No protection
$FE
$FF00–$FFFF
$FD
↓
$FE80–$FFFF
↓
$0B
$8580–$FFFF
$0A
$09
$8500–$FFFF
$8480–$FFFF
$08
↓
$8400–$FFFF
↓
$04
$8200–$FFFF
$03
$02
$01
$00
$8180–$FFFF
$8100–$FFFF
$8080–$FFFF
$8000–$FFFF
Data Sheet
50
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
FLASH-1 Memory (FLASH-1)
Decreasing the value in FL1BPR by one increases the protected range by one
page (128 bytes). However, programming the block protect register with $FE
protects a range twice that size, 256 bytes, in the corresponding array. $FE means
that locations $FF00–$FFFF are protected in FLASH-1.
The FLASH memory does not exist at some locations. The block protection range
configuration is unaffected if FLASH memory does not exist in that range. Refer to
Figure 2-1 and make sure that the desired locations are protected.
2.6.3 FLASH-1 Block Protection
Due to the ability of the on-board charge pump to erase and program the FLASH
memory in the target application, provision is made for protecting blocks of memory
from unintentional erase or program operations due to system malfunction. This
protection is done by using the FLASH-1 block protection register (FL1BPR).
FL1BPR determines the range of the FLASH-1 memory which is to be protected.
The range of the protected area starts from a location defined by FL1BPR and ends
at the bottom of the FLASH-1 memory ($FFFF). When the memory is protected,
the HVEN bit can not be set in either ERASE or PROGRAM operations.
NOTE:
In performing a program or erase operation, the FLASH-1 block protect register
must be read after setting the PGM or ERASE bit and before asserting the
HVEN bit.
When the FLASH-1 block protect register is programmed with all 0’s, the entire
memory is protected from being programmed and erased. When all the bits are
erased (all 1’s), the entire memory is accessible for program and erase.
When bits within FL1BPR are programmed (0), they lock a block of memory
address ranges as shown in Figure 2-4. If FL1BPR is programmed with any value
other than $FF, the protected block of FLASH memory can not be erased or
programmed.
NOTE:
The vector locations and the FLASH block protect registers are located in the same
page. FL1BPR and FL2BPR are not protected with special hardware or software.
Therefore, if this page is not protected by FL1BPR and the vector locations are
erased by either a page or a mass erase operation, then both FL1BPR and
FL2BPR will also get erased.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
51
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
2.6.4 FLASH-1 Mass Erase Operation
Use this step-by-step procedure to erase the entire FLASH-1 memory:
1. Set both the ERASE bit and the MASS bit in the FLASH-1 control register
(FL1CR).
2. Read the FLASH-1 block protect register (FL1BPR).
NOTE:
Mass erase is disabled whenever any block is protected (FL1BPR does not equal
$FF).
3. Write to any FLASH-1 address within the FLASH-1 array with any data.
4. Wait for a time, tNVS (minimum 10 µs).
5. Set the HVEN bit.
6. Wait for a time, tMERASE (minimum 4 ms).
7. Clear the ERASE and MASS bits.
8. Wait for a time, tNVHL (minimum 100 µs).
9. Clear the HVEN bit.
10. Wait for a time, tRCV, (typically 1 µs) after which the memory can be
accessed in normal read mode.
NOTES:
A. Programming and erasing of FLASH locations can not be performed by code
being executed from the same FLASH array.
B. While these operations must be performed in the order shown, other unrelated
operations may occur between the steps. However, care must be taken to
ensure that these operations do not access any address within the FLASH
array memory space such as the COP control register (COPCTL) at $FFFF.
C. It is highly recommended that interrupts be disabled during program/erase
operations.
2.6.5 FLASH-1 Page Erase Operation
Use this step-by-step procedure to erase a page (128 bytes) of FLASH-1 memory:
1. Set the ERASE bit and clear the MASS bit in the FLASH-1 control register
(FL1CR).
2. Read the FLASH-1 block protect register (FL1BPR).
3. Write any data to any FLASH-1 address within the address range of the
page (128 byte block) to be erased.
4. Wait for time, tNVS (minimum 10 µs).
5. Set the HVEN bit.
6. Wait for time, tERASE (minimum 1 ms or 4 ms).
7. Clear the ERASE bit.
8. Wait for time, tNVH (minimum 5 µs).
Data Sheet
52
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
FLASH-1 Memory (FLASH-1)
9. Clear the HVEN bit.
10. Wait for a time, tRCV, (typically 1 µs) after which the memory can be
accessed in normal read mode.
NOTES:
A. Programming and erasing of FLASH locations can not be performed by code
being executed from the same FLASH array.
B. While these operations must be performed in the order shown, other unrelated
operations may occur between the steps. However, care must be taken to
ensure that these operations do not access any address within the FLASH
array memory space such as the COP control register (COPCTL) at $FFFF.
C. It is highly recommended that interrupts be disabled during program/erase
operations.
In applications that require more than 1000 program/erase cycles, use the 4 ms
page erase specification to get improved long-term reliability. Any application can
use this 4 ms page erase specification. However, in applications where a FLASH
location will be erased and reprogrammed less than 1000 times, and speed is
important, use the 1 ms page erase specification to get a shorter cycle time.
2.6.6 FLASH-1 Program Operation
Programming of the FLASH-1 memory is done on a row basis. A row consists of
64 consecutive bytes with address ranges as follows:
•
•
•
•
$XX00 to $XX3F
$XX40 to $XX7F
$XX80 to $XXBF
$XXC0 to $XXFF
During the programming cycle, make sure that all addresses being written to fit
within one of the ranges specified above. Attempts to program addresses in
different row ranges in one programming cycle will fail.
Use this step-by-step procedure to program a row of FLASH-1 memory.
NOTE:
Only bytes which are currently $FF may be programmed.
1. Set the PGM bit in the FLASH-1 control register (FL1CR). This configures
the memory for program operation and enables the latching of address and
data programming.
2. Read the FLASH-1 block protect register (FL1BPR).
3. Write to any FLASH-1 address within the row address range desired with
any data.
4. Wait for time, tNVS (minimum 10 µs).
5. Set the HVEN bit.
6. Wait for time, tPGS (minimum 5 µs).
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
53
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
7. Write data byte to the FLASH-1 address to be programmed.
8. Wait for time, tPROG (minimum 30 µs).
9. Repeat steps 7 and 8 until all the bytes within the row are programmed.
10. Clear the PGM bit.
11. Wait for time, tNVH (minimum 5 µs)
12. Clear the HVEN bit.
13. Wait for a time, tRCV, (typically 1 µs) after which the memory can be
accessed in normal read mode.
The FLASH programming algorithm flowchart is shown in Figure 2-6.
NOTES:
A. Programming and erasing of FLASH locations can not be performed by code
being executed from the same FLASH array.
B. While these operations must be performed in the order shown, other unrelated
operations may occur between the steps. However, care must be taken to
ensure that these operations do not access any address within the FLASH
array memory space such as the COP control register (COPCTL) at $FFFF.
C. It is highly recommended that interrupts be disabled during program/erase
operations.
D. Do not exceed tPROG maximum or tHV maximum. tHV is defined as the
cumulative high voltage programming time to the same row before next erase.
t
HV must satisfy this condition:
NVS+ tNVH + tPGS + (tPROG X 64) ≤ tHV maximum
t
E. The time between each FLASH address change (step 7 to step 7), or the time
between the last FLASH address programmed to clearing the PGM bit (step 7
to step 10) must not exceed the maximum programming time, tPROG maximum.
F. Be cautious when programming the FLASH-1 array to ensure that non-FLASH
locations are not used as the address that is written to when selecting either the
desired row address range in step 3 of the algorithm or the byte to be
programmed in step 7 of the algorithm.
Data Sheet
54
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
FLASH-1 Memory (FLASH-1)
Algorithm for programming
a row (64 bytes) of FLASH memory
1
SET PGM BIT
READ THE FLASH BLOCK
PROTECT REGISTER
2
3
WRITE ANY DATA TO ANY FLASH
ADDRESS WITHIN THE ROW
ADDRESS RANGE DESIRED
4
5
6
WAIT FOR A TIME, t
NVS
SET HVEN BIT
WAIT FOR A TIME, t
PGS
7
8
WRITE DATA TO THE FLASH
ADDRESS TO BE PROGRAMMED
WAIT FOR A TIME, t
PROG
COMPLETED
PROGRAMMING
THIS ROW?
YES
NO
10
CLEAR PGM BIT
11
12
13
WAIT FOR A TIME, t
NVH
NOTES:
CLEAR HVEN BIT
The time between each FLASH address change (step 7 to step 7) or
the time between the last FLASH address programmed to clearing
PGM bit (step 7 to step10) must not exceed the maximum
programming time, tPROG, maximum.
WAIT FOR A TIME, t
RCV
This row program algorithm assumes the row/s to be
programmed are initially erased.
END OF PROGRAMMING
Figure 2-6. FLASH-1 Programming Algorithm Flowchart
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
55
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
2.6.7 Low-Power Modes
The WAIT and STOP instructions will place the MCU in low power-consumption
standby modes.
2.6.7.1 Wait Mode
Putting the MCU into wait mode while the FLASH is in read mode does not affect
the operation of the FLASH memory directly; however, no memory activity will take
place since the CPU is inactive.
The WAIT instruction should not be executed while performing a program or erase
operation on the FLASH. Wait mode will suspend any FLASH program/erase
operations and leave the memory in a standby mode.
2.6.7.2 Stop Mode
Putting the MCU into stop mode while the FLASH is in read mode does not affect
the operation of the FLASH memory directly; however, no memory activity will take
place since the CPU is inactive.
The STOP instruction should not be executed while performing a program or erase
operation on the FLASH. Stop mode will suspend any FLASH program/erase
operations and leave the memory in a standby mode.
NOTE:
Standby mode is the power saving mode of the FLASH module, in which all internal
control signals to the FLASH are inactive and the current consumption of the
FLASH is minimum.
2.7 FLASH-2 Memory (FLASH-2)
This subsection describes the operation of the embedded FLASH-2 memory. This
memory can be read, programmed, and erased from a single external supply. The
program and erase operations are enabled through the use of an internal charge
pump.
2.7.1 Functional Description
The FLASH-2 memory is a non-continuous array consisting of a total of 29,822
bytes. An erased bit reads as a 1 and a programmed bit reads as a 0.
Memory in the FLASH-2 array is organized into rows within pages. There are two
rows of memory per page with 64 bytes per row. The minimum erase block size is
a single page,128 bytes. Programming is performed on a per-row basis, 64 bytes
at a time. Program and erase operations are facilitated through control bits in the
FLASH-2 control register (FL2CR). Details for these operations appear later in this
subsection.
Data Sheet
56
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
FLASH-2 Memory (FLASH-2)
The FLASH-2 memory map consists of:
•
•
•
•
$0462–$04FF: user memory (158 bytes)
$0980–$1B7F: user memory (4608 bytes)
$1E20–$7FFF: user memory (25056 bytes)
$FF81: FLASH-2 block protect register (FL2BPR)
NOTE:
NOTE:
FL2BPR physically resides within FLASH-1 memory addressing space
$FE08: FLASH-2 control register (FL2CR)
•
Programming tools are available from Motorola. Contact your local Motorola
representative for more information.
A security feature prevents viewing of the FLASH contents.(1)
2.7.2 FLASH-2 Control and Block Protect Registers
The FLASH-2 array has two registers that control its operation, the FLASH-2
control register (FL2CR) and the FLASH-2 block protect register (FL2BPR).
2.7.2.1 FLASH-2 Control Register
The FLASH-2 control register (FL2CR) controls FLASH-2 program and erase
operations.
Address:
$FE08
Bit 7
0
6
0
5
0
4
0
3
HVEN
0
2
MASS
0
1
ERASE
0
Bit 0
PGM
0
Read:
Write:
Reset:
0
0
0
0
Figure 2-7. FLASH-2 Control Register (FL2CR)
HVEN — High-Voltage Enable Bit
This read/write bit enables the charge pump to drive high voltages for program
and erase operations in the array. HVEN can only be set if either PGM = 1 or
ERASE = 1 and the proper sequence for program or erase is followed.
1 = High voltage enabled to array and charge pump on
0 = High voltage disabled to array and charge pump off
MASS — Mass Erase Control Bit
Setting this read/write bit configures the FLASH-2 array for mass or page erase
operation.
1 = Mass erase operation selected
0 = Page erase operation selected
1. No security feature is absolutely secure. However, Motorola’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
57
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
ERASE — Erase Control Bit
This read/write bit configures the memory for erase operation. ERASE is
interlocked with the PGM bit such that both bits cannot be set at the same time.
1 = Erase operation selected
0 = Erase operation unselected
PGM — Program Control Bit
This read/write bit configures the memory for program operation. PGM is
interlocked with the ERASE bit such that both bits cannot be equal to 1 or set
to 1 at the same time.
1 = Program operation selected
0 = Program operation unselected
2.7.2.2 FLASH-2 Block Protect Register
The FLASH-2 block protect register (FL2BPR) is implemented as a byte within the
FLASH-1 memory; therefore, can only be written during a FLASH-1 programming
sequence. The value in this register determines the starting location of the
protected range within the FLASH-2 memory.
Address:
$FF81
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
BPR7
BPR6
BPR5
BPR4
BPR3
BPR2
BPR1
BPR0
Unaffected by reset
Figure 2-8. FLASH-2 Block Protect Register (FL2BPR)
NOTE:
The FLASH-2 block protect register (FL2BPR) controls the block protection for the
FLASH-2 array. However, FL2BPR is implemented within the FLASH-1 memory
array and therefore, the FLASH-1 control register (FL1CR) must be used to
program/erase FL2BPR.
FL2BPR[7:0] — Block Protect Register Bits 7 to 0
These eight bits represent bits [14:7] of a 16-bit memory address. Bit 15 is a 0
and bits [6:0] are 0s.
The resultant 16-bit address is used for specifying the start address of the
FLASH-2 memory for block protection. FLASH-2 is protected from this start
address to the end of FLASH-2 memory at $7FFF. With this mechanism, the
protect start address can be $XX00 and $XX80 (128 byte page boundaries)
within the FLASH-2 array.
16-BIT MEMORY ADDRESS
START ADDRESS OF FLASH
BLOCK PROTECT
0
0
0
0
0
0
0
FLBPR VALUE
0
Figure 2-9. FLASH-2 Block Protect Start Address
Data Sheet
58
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
FLASH-2 Memory (FLASH-2)
Table 2-3. FLASH-2 Protected Ranges
FL2BPR[7:0]
Protected Range
No Protection
$FF
$FE
$7F00–$7FFF
$FD
↓
$7E80–$7FFF
↓
$0B
$0580–$7FFF
$0A
$09
$0500–$7FFF
$0480–$7FFF
$08
↓
$0462–$7FFF
↓
$04
$0462–$7FFF
$03
$02
$01
$00
$0462–$7FFF
$0462–$7FFF
$0462–$7FFF
$0462–$7FFF
Decreasing the value in FL2BPR by one increases the protected range by one
page (128 bytes). However, programming the block protect register with $FE
protects a range twice that size, 256 bytes, in the corresponding array. $FE means
that locations $7F00–$7FFF are protected in FLASH-2.
The FLASH memory does not exist at some locations. The block protection range
configuration is unaffected if FLASH memory does not exist in that range. Refer to
Figure 2-1 and make sure that the desired locations are protected.
2.7.3 FLASH-2 Block Protection
Due to the ability of the on-board charge pump to erase and program the FLASH
memory in the target application, provision is made for protecting blocks of memory
from unintentional erase or program operations due to system malfunction. This
protection is done by using the FLASH-2 block protection register (FL2BPR).
FL2BPR determines the range of the FLASH-2 memory which is to be protected.
The range of the protected area starts from a location defined by FL2BPR and ends
at the bottom of the FLASH-2 memory ($7FFF). When the memory is protected,
the HVEN bit can not be set in either ERASE or PROGRAM operations.
NOTE:
In performing a program or erase operation, the FLASH-2 block protect register
must be read after setting the PGM or ERASE bit and before asserting the
HVEN bit.
When the FLASH-2 block protect register is programmed with all 0’s, the entire
memory is protected from being programmed and erased. When all the bits are
erased (all 1’s), the entire memory is accessible for program and erase.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
59
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
When bits within FL2BPR are programmed (0), they lock a block of memory
address ranges as shown in 2.7.2.2 FLASH-2 Block Protect Register. If FL2BPR
is programmed with any value other than $FF, the protected block of FLASH
memory can not be erased or programmed.
NOTE:
The vector locations and the FLASH block protect registers are located in the same
page. FL1BPR and FL2BPR are not protected with special hardware or software.
Therefore, if this page is not protected by FL1BPR and the vector locations are
erased by either a page or a mass erase operation, both FL1BPR and FL2BPR will
also get erased.
2.7.4 FLASH-2 Mass Erase Operation
Use this step-by-step procedure to erase the entire FLASH-2 memory:
1. Set both the ERASE bit and the MASS bit in the FLASH-2 control register
(FL2CR).
2. Read the FLASH-2 block protect register (FL2BPR).
NOTE:
Mass erase is disabled whenever any block is protected (FL2BPR does not equal
$FF).
3. Write to any FLASH-2 address within the FLASH-2 array with any data.
4. Wait for a time, tNVS (minimum 10 µs).
5. Set the HVEN bit.
6. Wait for a time, tMERASE (minimum 4 ms).
7. Clear the ERASE and MASS bits.
8. Wait for a time, tNVHL (minimum 100 µs).
9. Clear the HVEN bit.
10. Wait for a time, tRCV, (typically 1 µs) after which the memory can be
accessed in normal read mode.
NOTES:
A. Programming and erasing of FLASH locations can not be performed by code
being executed from the same FLASH array.
B. While these operations must be performed in the order shown, other unrelated
operations may occur between the steps. However, care must be taken to
ensure that these operations do not access any address within the FLASH
array memory space such as the COP control register (COPCTL) at $FFFF.
C. It is highly recommended that interrupts be disabled during program/erase
operations.
Data Sheet
60
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
FLASH-2 Memory (FLASH-2)
2.7.5 FLASH-2 Page Erase Operation
Use this step-by-step procedure to erase a page (128 bytes) of FLASH-2 memory:
1. Set the ERASE bit and clear the MASS bit in the FLASH-2 control register
(FL2CR).
2. Read the FLASH-2 block protect register (FL2BPR).
3. Write any data to any FLASH-2 address within the address range of the
page (128 byte block) to be erased.
4. Wait for time, tNVS (minimum 10 µs).
5. Set the HVEN bit.
6. Wait for time, tERASE (minimum 1 ms or 4 ms).
7. Clear the ERASE bit.
8. Wait for time, tNVH (minimum 5 µs).
9. Clear the HVEN bit.
10. Wait for a time, tRCV, (typically 1 µs) after which the memory can be
accessed in normal read mode.
NOTES:
A. Programming and erasing of FLASH locations can not be performed by code
being executed from the same FLASH array.
B. While these operations must be performed in the order shown, other unrelated
operations may occur between the steps. However, care must be taken to
ensure that these operations do not access any address within the FLASH
array memory space such as the COP control register (COPCTL) at $FFFF.
C. It is highly recommended that interrupts be disabled during program/erase
operations.
In applications that require more than 1000 program/erase cycles, use the 4 ms
page erase specification to get improved long-term reliability. Any application can
use this 4 ms page erase specification. However, in applications where a FLASH
location will be erased and reprogrammed less than 1000 times, and speed is
important, use the 1 ms page erase specification to get a shorter cycle time.
2.7.6 FLASH-2 Program Operation
Programming of the FLASH memory is done on a row basis. A row consists of 64
consecutive bytes with address ranges as follows:
•
•
•
•
$XX00 to $XX3F
$XX40 to $XX7F
$XX80 to $XXBF
$XXC0 to $XXFF
During the programming cycle, make sure that all addresses being written to fit
within one of the ranges specified above. Attempts to program addresses in
different row ranges in one programming cycle will fail.
NOTE:
Only bytes which are currently $FF may be programmed.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
61
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
Use this step-by-step procedure to program a row of FLASH-2 memory:
1. Set the PGM bit in the FLASH-2 control register (FL2CR). This configures
the memory for program operation and enables the latching of address and
data programming.
2. Read the FLASH-2 block protect register (FL2BPR).
3. Write to any FLASH-2 address within the row address range desired with
any data.
4. Wait for time, tNVS (minimum 10 µs).
5. Set the HVEN bit.
6. Wait for time, tPGS (minimum 5 µs).
7. Write data byte to the FLASH-2 address to be programmed.
8. Wait for time, t PROG (minimum 30 µs).
9. Repeat step 7 and 8 until all the bytes within the row are programmed.
10. Clear the PGM bit.
11. Wait for time, tNVH (minimum 5 µs).
12. Clear the HVEN bit.
13. Wait for a time, tRCV, (typically 1 µs) after which the memory can be
accessed in normal read mode.
The FLASH programming algorithm flowchart is shown in Figure 2-10.
NOTES:
A. Programming and erasing of FLASH locations can not be performed by code
being executed from the same FLASH array.
B. While these operations must be performed in the order shown, other unrelated
operations may occur between the steps. However, care must be taken to
ensure that these operations do not access any address within the FLASH
array memory space such as the COP control register (COPCTL) at $FFFF.
C. It is highly recommended that interrupts be disabled during program/erase
operations.
D. Do not exceed t PROG maximum or tHV maximum. tHV is defined as the
cumulative high voltage programming time to the same row before next erase.
t
HV must satisfy this condition:
NVS+ tNVH + tPGS + (tPROG X 64) ≤ tHV maximum
t
E. The time between each FLASH address change (step 7 to step 7), or the time
between the last FLASH address programmed to clearing the PGM bit (step 7
to step 10) must not exceed the maximum programming time, tPROG maximum.
F. Be cautious when programming the FLASH-2 array to ensure that non-FLASH
locations are not used as the address that is written to when selecting either the
desired row address range in step 3 of the algorithm or the byte to be
programmed in step 7 of the algorithm.
Data Sheet
62
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
FLASH-2 Memory (FLASH-2)
Algorithm for programming
a row (64 bytes) of FLASH memory
1
SET PGM BIT
READ THE FLASH BLOCK
PROTECT REGISTER
2
3
WRITE ANY DATA TO ANY FLASH
ADDRESS WITHIN THE ROW
ADDRESS RANGE DESIRED
4
5
6
WAIT FOR A TIME, t
NVS
SET HVEN BIT
WAIT FOR A TIME, t
PGS
7
8
WRITE DATA TO THE FLASH
ADDRESS TO BE PROGRAMMED
WAIT FOR A TIME, t
PROG
COMPLETED
PROGRAMMING
THIS ROW?
YES
NO
10
CLEAR PGM BIT
11
12
13
WAIT FOR A TIME, t
NVH
NOTES:
CLEAR HVEN BIT
The time between each FLASH address change (step 7 to step 7) or
the time between the last FLASH address programmed to clearing
PGM bit (step 7 to step10) must not exceed the maximum
programming time, tPROG, maximum.
WAIT FOR A TIME, t
RCV
This row program algorithm assumes the row/s to be
programmed are initially erased.
END OF PROGRAMMING
Figure 2-10. FLASH-2 Programming Algorithm Flowchart
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
63
MOTOROLA
Memory
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Memory
2.7.7 Low-Power Modes
The WAIT and STOP instructions will place the MCU in low power-consumption
standby modes.
2.7.7.1 Wait Mode
Putting the MCU into wait mode while the FLASH is in read mode does not affect
the operation of the FLASH memory directly; however, no memory activity will take
place since the CPU is inactive.
The WAIT instruction should not be executed while performing a program or erase
operation on the FLASH. Wait mode will suspend any FLASH program/erase
operations and leave the memory in a standby mode.
2.7.7.2 Stop Mode
Putting the MCU into stop mode while the FLASH is in read mode does not affect
the operation of the FLASH memory directly; however, no memory activity will take
place since the CPU is inactive.
The STOP instruction should not be executed while performing a program or erase
operation on the FLASH. Stop mode will suspend any FLASH program/erase
operations and leave the memory in a standby mode.
NOTE:
Standby mode is the power saving mode of the FLASH module, in which all internal
control signals to the FLASH are inactive and the current consumption of the
FLASH is minimum.
Data Sheet
64
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Memory
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 3. Analog-to-Digital Converter (ADC)
3.1 Introduction
3.2 Features
This section describes the 10-bit analog-to-digital converter (ADC).
Features of the ADC module include:
•
•
•
•
•
•
•
•
24 channels with multiplexed input
Linear successive approximation with monotonicity
10-bit resolution
Single or continuous conversion
Conversion complete flag or conversion complete interrupt
Selectable ADC clock
Left or right justified result
Left justified sign data mode
3.3 Functional Description
The ADC provides 24 pins for sampling external sources at pins
PTG7/AD23–PTG0/AD16, PTA7/KBD7/AD15–PTA0/KBD0/AD8, and
PTB7/AD7–PTB0/AD0. An analog multiplexer allows the single ADC converter to
select one of 24 ADC channels as ADC voltage in (VADIN). VADIN is converted by
the successive approximation register-based analog-to-digital converter. When the
conversion is completed, ADC places the result in the ADC data register and sets
a flag or generates an interrupt. See Figure 3-2.
3.3.1 ADC Port I/O Pins
PTG7/AD23–PTG0/AD16, PTA7/KBD7/AD15–PTA0/KBD0/AD8, and
PTB7/AD7–PTB0/AD0 are general-purpose I/O (input/output) pins that share with
the ADC channels. The channel select bits define which ADC channel/port pin will
be used as the input signal. The ADC overrides the port I/O logic by forcing that pin
as input to the ADC. The remaining ADC channels/port pins are controlled by the
port I/O logic and can be used as general-purpose I/O. Writes to the port register
or data direction register (DDR) will not have any affect on the port pin that is
selected by the ADC. A read of a port pin in use by the ADC will return a 0.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
65
MOTOROLA
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
B
P O R T
D D R B
P O R T F
D D R F
G T R P O
D D R G
A T R P O
D D R A
C
P O R T
D D R C
E
P O R T
D D R E
P O R T D
D D R
D
Data Sheet
66
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Analog-to-Digital Converter (ADC) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
Functional Description
INTERNAL
DATA BUS
READ DDRx
WRITE DDRx
DISABLE
DDRx
PTx
RESET
WRITE PTx
READ PTx
PTx
ADC CHANNEL x
DISABLE
ADC DATA REGISTER
ADC
VOLTAGE IN
(VADIN
CONVERSION
COMPLETE
ADCH4–ADCH0
)
CHANNEL
SELECT
INTERRUPT
ADC
LOGIC
ADC CLOCK
AIEN COCO
CGMXCLK
CLOCK
GENERATOR
BUS CLOCK
ADIV2–ADIV0 ADICLK
Figure 3-2. ADC Block Diagram
3.3.2 Voltage Conversion
When the input voltage to the ADC equals VREFH, the ADC converts the signal to
$3FF (full scale). If the input voltage equals VREFL, the ADC converts it to $000.
Input voltages between VREFH and VREFL are a straight-line linear conversion.
NOTE:
The ADC input voltage must always be greater than VSSAD and less than VDDAD.
Connect the VDDAD pin to the same voltage potential as the VDD pin, and connect
the VSSAD pin to the same voltage potential as the VSS pin.
The VDDAD pin should be routed carefully for maximum noise immunity.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
67
MOTOROLA
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
3.3.3 Conversion Time
Conversion starts after a write to the ADC status and control register (ADSCR).
One conversion will take between 16 and 17 ADC clock cycles. The ADIVx and
ADICLK bits should be set to provide a 1-MHz ADC clock frequency.
16 to 17 ADC cycles
Conversion time =
ADC frequency
Number of bus cycles = conversion time × bus frequency
3.3.4 Conversion
In continuous conversion mode, the ADC data register will be filled with new data
after each conversion. Data from the previous conversion will be overwritten
whether that data has been read or not. Conversions will continue until the ADCO
bit is cleared. The COCO bit is set after each conversion and will stay set until the
next read of the ADC data register.
In single conversion mode, conversion begins with a write to the ADSCR. Only one
conversion occurs between writes to the ADSCR.
When a conversion is in process and the ADSCR is written, the current conversion
data should be discarded to prevent an incorrect reading.
3.3.5 Accuracy and Precision
The conversion process is monotonic and has no missing codes.
3.3.6 Result Justification
The conversion result may be formatted in four different ways:
1. Left justified
2. Right justified
3. Left Justified sign data mode
4. 8-bit truncation mode
All four of these modes are controlled using MODE0 and MODE1 bits located in
the ADC clock register (ADCLK).
Left justification will place the eight most significant bits (MSB) in the corresponding
ADC data register high, ADRH. This may be useful if the result is to be treated as
an 8-bit result where the two least significant bits (LSB), located in the ADC data
register low, ADRL, can be ignored. However, ADRL must be read after ADRH or
else the interlocking will prevent all new conversions from being stored.
Data Sheet
68
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Analog-to-Digital Converter (ADC)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
Monotonicity
Right justification will place only the two MSBs in the corresponding ADC data
register high, ADRH, and the eight LSBs in ADC data register low, ADRL. This
mode of operation typically is used when a 10-bit unsigned result is desired.
Left justified sign data mode is similar to left justified mode with one exception. The
MSB of the 10-bit result, AD9 located in ADRH, is complemented. This mode of
operation is useful when a result, represented as a signed magnitude from
mid-scale, is needed. Finally, 8-bit truncation mode will place the eight MSBs in the
ADC data register low, ADRL. The two LSBs are dropped. This mode of operation
is used when compatibility with 8-bit ADC designs are required. No interlocking
between ADRH and ADRL is present.
NOTE:
Quantization error is affected when only the most significant eight bits are used as
a result. See Figure 3-3.
8-BIT 10-BIT
IDEAL 8-BIT CHARACTERISTIC
RESULT RESULT
WITH QUANTIZATION = 1/2
10-BIT TRUNCATED
TO 8-BIT RESULT
003
00B
00A
IDEAL 10-BIT CHARACTERISTIC
009
008
007
006
005
004
003
002
001
000
WITH QUANTIZATION = 1/2
002
001
000
WHEN TRUNCATION IS USED,
ERROR FROM IDEAL 8-BIT = 3/8 LSB
DUE TO NON-IDEAL QUANTIZATION.
INPUT VOLTAGE
1/2
2 1/2
4 1/2
6 1/2
8 1/2
REPRESENTED AS 10-BIT
9 1/2
INPUT VOLTAGE
1 1/2
3 1/2
5 1/2
7 1/2
1/2
1 1/2
2 1/2
REPRESENTED AS 8-BIT
Figure 3-3. Bit Truncation Mode Error
3.4 Monotonicity
The conversion process is monotonic and has no missing codes.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
69
MOTOROLA
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
3.5 Interrupts
When the AIEN bit is set, the ADC module is capable of generating CPU interrupts
after each ADC conversion. A CPU interrupt is generated if the COCO bit is a 0.
The COCO bit is not used as a conversion complete flag when interrupts are
enabled.
3.6 Low-Power Modes
The WAIT and STOP instruction can put the MCU in low power- consumption
standby modes.
3.6.1 Wait Mode
The ADC continues normal operation during wait mode. Any enabled CPU interrupt
request from the ADC can bring the MCU out of wait mode. If the ADC is not
required to bring the MCU out of wait mode, power down the ADC by setting
ADCH4–ADCH0 bits in the ADC status and control register before executing the
WAIT instruction.
3.6.2 Stop Mode
3.7 I/O Signals
The ADC module is inactive after the execution of a STOP instruction. Any pending
conversion is aborted. ADC conversions resume when the MCU exits stop mode
after an external interrupt. Allow one conversion cycle to stabilize the analog
circuitry.
The ADC module has eight pins shared with port A and the KBI module:
PTA7/KBD7/AD15–PTA0/KBD0/AD8
The ADC module has eight pins shared with port B:
PTB7/AD7–PTB0/AD0
The ADC module has eight pins shared with port G:
PTG7/AD23–PTG0/AD16
3.7.1 ADC Analog Power Pin (VDDAD
)
The ADC analog portion uses VDDAD as its power pin. Connect the VDDAD pin to
the same voltage potential as VDD. External filtering may be necessary to ensure
clean VDDAD for good results.
NOTE:
For maximum noise immunity, route VDDAD carefully and place bypass capacitors
as close as possible to the package.
VDDAD and VREFH are bonded internally.
Data Sheet
70
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Analog-to-Digital Converter (ADC)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
I/O Registers
3.7.2 ADC Analog Ground Pin (VSSAD
)
The ADC analog portion uses VSSAD as its ground pin. Connect the VSSAD pin to
the same voltage potential as VSS.
NOTE:
Route VSSAD cleanly to avoid any offset errors.
VSSAD and VREFL are bonded internally.
3.7.3 ADC Voltage Reference High Pin (VREFH
)
The ADC analog portion uses VREFH as its upper voltage reference pin. By default,
connect the VREFH pin to the same voltage potential as VDD. External filtering is
often necessary to ensure a clean VREFH for good results. Any noise present on
this pin will be reflected and possibly magnified in A/D conversion values.
NOTE:
For maximum noise immunity, route VREFH carefully and place bypass capacitors
as close as possible to the package. Routing VREFH close and parallel to VREFL
may improve common mode noise rejection.
VDDAD and VREFH are bonded internally.
3.7.4 ADC Voltage Reference Low Pin (VREFL
)
The ADC analog portion uses VREFL as its lower voltage reference pin. By default,
connect the VREFL pin to the same voltage potential as VSS. External filtering is
often necessary to ensure a clean VREFL for good results. Any noise present on this
pin will be reflected and possibly magnified in A/D conversion values.
NOTE:
For maximum noise immunity, route VREFL carefully and, if not connected to VSS,
place bypass capacitors as close as possible to the package. Routing VREFH close
and parallel to VREFL may improve common mode noise rejection.
VSSAD and VREFL are bonded internally.
3.7.5 ADC Voltage In (VADIN
)
VADIN is the input voltage signal from one of the 24 ADC channels to the ADC
module.
3.8 I/O Registers
These I/O registers control and monitor ADC operation:
•
•
•
ADC status and control register (ADSCR)
ADC data register (ADRH and ADRL)
ADC clock register (ADCLK)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
71
MOTOROLA
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
3.8.1 ADC Status and Control Register
Function of the ADC status and control register (ADSCR) is described here.
Address:
$003C
Bit 7
6
5
ADCO
0
4
ADCH4
1
3
ADCH3
1
2
ADCH2
1
1
ADCH1
1
Bit 0
ADCH0
1
Read:
Write:
Reset:
COCO
AIEN
R
0
0
R
= Reserved
Figure 3-4. ADC Status and Control Register (ADSCR)
COCO — Conversions Complete Bit
In non-interrupt mode (AIEN = 0), COCO is a read-only bit that is set at the end
of each conversion. COCO will stay set until cleared by a read of the ADC data
register. Reset clears this bit.
In interrupt mode (AIEN = 1), COCO is a read-only bit that is not set at the end
of a conversion. It always reads as a 0.
1 = Conversion completed (AIEN = 0)
0 = Conversion not completed (AIEN = 0) or CPU interrupt enabled
(AIEN = 1)
NOTE:
The write function of the COCO bit is reserved. When writing to the ADSCR
register, always have a 0 in the COCO bit position.
AIEN — ADC Interrupt Enable Bit
When this bit is set, an interrupt is generated at the end of an ADC conversion.
The interrupt signal is cleared when the data register is read or the status/control
register is written. Reset clears the AIEN bit.
1 = ADC interrupt enabled
0 = ADC interrupt disabled
ADCO — ADC Continuous Conversion Bit
When set, the ADC will convert samples continuously and update the ADR
register at the end of each conversion. Only one conversion is completed
between writes to the ADSCR when this bit is cleared. Reset clears the ADCO
bit.
1 = Continuous ADC conversion
0 = One ADC conversion
ADCH4–ADCH0 — ADC Channel Select Bits
ADCH4–ADCH0 form a 5-bit field which is used to select one of 32 ADC
channels. Only 24 channels, AD23–AD0, are available on this MCU. The
channels are detailed in Table 3-1. Care should be taken when using a port pin
as both an analog and digital input simultaneously to prevent switching noise
from corrupting the analog signal. See Table 3-1.
Data Sheet
72
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Analog-to-Digital Converter (ADC)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
I/O Registers
The ADC subsystem is turned off when the channel select bits are all set to 1.
This feature allows for reduced power consumption for the MCU when the ADC
is not being used.
NOTE:
Recovery from the disabled state requires one conversion cycle to stabilize.
The voltage levels supplied from internal reference nodes, as specified in
Table 3-1, are used to verify the operation of the ADC converter both in production
test and for user applications.
Table 3-1. Mux Channel Select(1)
ADCH4
ADCH3
ADCH2
ADCH1
ADCH0
Input Select
PTB0/AD0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
PTB1/AD1
PTB2/AD2
PTB3/AD3
PTB4/AD4
PTB5/AD5
PTB6/AD6
PTB7/AD7
PTA0/KBD0/AD8
PTA1/KBD1/AD9
PTA2/KBD2/AD10
PTA3/KBD3/AD11
PTA4/KBD4/AD12
PTA5/KBD5/AD13
PTA6/KBD6/AD14
PTA7/KBD7/AD15
PTG0/AD16
PTG1/AD17
PTG2/AD18
PTG3/AD19
PTG4/AD20
PTG5/AD21
PTG6/AD22
PTG7/AD23
1
↓
1
1
↓
1
0
↓
1
0
↓
0
0
↓
0
Unused
VREFH
VREFL
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
ADC power off
1. If any unused channels are selected, the resulting ADC conversion will be unknown or
reserved.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
73
MOTOROLA
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
3.8.2 ADC Data Register High and Data Register Low
3.8.2.1 Left Justified Mode
In left justified mode, the ADRH register holds the eight MSBs of the
10-bit result. The ADRL register holds the two LSBs of the 10-bit result. All other
bits read as 0. ADRH and ADRL are updated each time an ADC single channel
conversion completes. Reading ADRH latches the contents of ADRL until ADRL is
read. All subsequent results will be lost until the ADRH and ADRL reads are
completed.
Address:
$003D
Bit 7
ADRH
Bit 0
6
5
4
3
2
1
Read:
Write:
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
Reset:
Address:
Read:
Unaffected by reset
$003E
AD1
ADRL
0
AD0
0
0
0
0
0
Write:
Reset:
Unaffected by reset
= Unimplemented
Figure 3-5. ADC Data Register High (ADRH) and Low (ADRL)
3.8.2.2 Right Justified Mode
In right justified mode, the ADRH register holds the two MSBs of the
10-bit result. All other bits read as 0. The ADRL register holds the eight LSBs of the
10-bit result. ADRH and ADRL are updated each time an ADC single channel
conversion completes. Reading ADRH latches the contents of ADRL until ADRL is
read. All subsequent results will be lost until the ADRH and ADRL reads are
completed.
Address:
$003D
Bit 7
0
ADRH
Bit 0
6
0
5
0
4
0
3
0
2
0
1
Read:
Write:
AD9
AD8
Reset:
Address:
Read:
Unaffected by reset
$003E
AD7
ADRL
AD0
AD6
AD5
AD4
AD3
AD2
AD1
Write:
Reset:
Unaffected by reset
= Unimplemented
Figure 3-6. ADC Data Register High (ADRH) and Low (ADRL)
Data Sheet
74
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Analog-to-Digital Converter (ADC)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
I/O Registers
3.8.2.3 Left Justified Signed Data Mode
In left justified signed data mode, the ADRH register holds the eight MSBs of the
10-bit result. The only difference from left justified mode is that the AD9 is
complemented. The ADRL register holds the two LSBs of the 10-bit result. All other
bits read as 0. ADRH and ADRL are updated each time an ADC single channel
conversion completes. Reading ADRH latches the contents of ADRL until ADRL is
read. All subsequent results will be lost until the ADRH and ADRL reads are
completed.
Address:
$003D
Bit 7
6
5
4
3
2
1
Bit 0
AD2
Read:
Write:
AD9
AD8
AD7
AD6
AD5
AD4
AD3
Reset:
Address:
Read:
Unaffected by reset
$003E
AD1
AD0
0
0
0
0
0
0
Write:
Reset:
Unaffected by reset
= Unimplemented
Figure 3-7. ADC Data Register High (ADRH) and Low (ADRL)
3.8.2.4 Eight Bit Truncation Mode
In 8-bit truncation mode, the ADRL register holds the eight MSBs of the 10-bit
result. The ADRH register is unused and reads as 0. The ADRL register is updated
each time an ADC single channel conversion completes. In 8-bit mode, the ADRL
register contains no interlocking with ADRH.
Address:
$003D
Bit 7
0
ADRH
Bit 0
0
6
0
5
0
4
0
3
0
2
0
1
0
Read:
Write:
Reset:
Address:
Read:
Unaffected by reset
$003E
AD9
ADRL
AD2
AD8
AD7
AD6
AD5
AD4
AD3
Write:
Reset:
Unaffected by reset
= Unimplemented
Figure 3-8. ADC Data Register High (ADRH) and Low (ADRL)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
75
MOTOROLA
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
3.8.3 ADC Clock Register
The ADC clock register (ADCLK) selects the clock frequency for the ADC.
Address:
$003F
Bit 7
6
ADIV1
0
5
ADIV0
0
4
3
2
MODE0
1
1
R
0
Bit 0
0
Read:
Write:
Reset:
ADIV2
0
ADICLK
MODE1
0
0
0
= Unimplemented
R
= Reserved
Figure 3-9. ADC Clock Register (ADCLK)
ADIV2–ADIV0 — ADC Clock Prescaler Bits
ADIV2–ADIV0 form a 3-bit field which selects the divide ratio used by the ADC
to generate the internal ADC clock. Table 3-2 shows the available clock
configurations. The ADC clock should be set to approximately 1 MHz.
Table 3-2. ADC Clock Divide Ratio
ADIV2
ADIV1
ADIV0
ADC Clock Rate
ADC input clock ÷ 1
ADC input clock ÷ 2
ADC input clock ÷ 4
ADC input clock ÷ 8
ADC input clock ÷ 16
0
0
0
0
1
0
0
1
1
0
1
0
1
X(1)
X(1)
1. X = Don’t care
ADICLK — ADC Input Clock Select Bit
ADICLK selects either the bus clock or the oscillator output clock (CGMXCLK)
as the input clock source to generate the internal ADC clock. Reset selects
CGMXCLK as the ADC clock source.
1 = Internal bus clock
0 = Oscillator output clock (CGMXCLK)
The ADC requires a clock rate of approximately 1 MHz for correct operation. If the
selected clock source is not fast enough, the ADC will generate incorrect
conversions. See 21.10 5.0-Volt ADC Characteristics.
f
or bus frequency
CGMXCLK
≅ 1 MHz
f
=
ADIC
ADIV[2:0]
Data Sheet
76
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Analog-to-Digital Converter (ADC)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
I/O Registers
MODE1 and MODE0 — Modes of Result Justification Bits
MODE1 and MODE0 select among four modes of operation. The manner in
which the ADC conversion results will be placed in the ADC data registers is
controlled by these modes of operation. Reset returns right-justified mode.
00 = 8-bit truncation mode
01 = Right justified mode
10 = Left justified mode
11 = Left justified signed data mode
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
77
MOTOROLA
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
Data Sheet
78
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Analog-to-Digital Converter (ADC)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 4. Clock Generator Module (CGM)
4.1 Introduction
This section describes the clock generator module. The CGM generates the crystal
clock signal, CGMXCLK, which operates at the frequency of the crystal. The CGM
also generates the base clock signal, CGMOUT, which is based on either the
crystal clock divided by two or the phase-locked loop (PLL) clock, CGMVCLK,
divided by two. In user mode, CGMOUT is the clock from which the SIM derives
the system clocks, including the bus clock, which is at a frequency of CGMOUT/2.
The PLL is a fully functional frequency generator designed for use with crystals or
ceramic resonators. The PLL can generate a maximum bus frequency of 8 MHz
using a 1-8MHz crystal or external clock source.
4.2 Features
Features of the CGM include:
•
•
•
Phase-locked loop with output frequency in integer multiples of an integer
dividend of the crystal reference
High-frequency crystal operation with low-power operation and high-output
frequency resolution
Programmable hardware voltage-controlled oscillator (VCO) for low-jitter
operation
•
•
•
•
Automatic bandwidth control mode for low-jitter operation
Automatic frequency lock detector
CPU interrupt on entry or exit from locked condition
Configuration register bit to allow oscillator operation during stop mode
4.3 Functional Description
The CGM consists of three major submodules:
•
•
•
Crystal oscillator circuit — The crystal oscillator circuit generates the
constant crystal frequency clock, CGMXCLK.
Phase-locked loop (PLL) — The PLL generates the programmable VCO
frequency clock, CGMVCLK.
Base clock selector circuit — This software-controlled circuit selects either
CGMXCLK divided by two or the VCO clock, CGMVCLK, divided by two as
the base clock, CGMOUT. The SIM derives the system clocks from either
CGMOUT or CGMXCLK.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
79
MOTOROLA
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Figure 4-1 shows the structure of the CGM.
OSCILLATOR (OSC)
OSC2
CGMXCLK
(TO: SIM, TBM, ADC, MSCAN)
OSC1
SIMOSCEN (FROM SIM)
OSCENINSTOP
(FROM CONFIG)
PHASE-LOCKED LOOP (PLL)
CGMRCLK
CGMOUT
(TO SIM)
A
B
CLOCK
SELECT
CIRCUIT
÷
2
BCS
S*
SIMDIV2
*WHEN S = 1,
CGMOUT = B
VDDA
CGMXFC
VSSA
(FROM SIM)
VPR1–VPR0
VRS7–VRS0
VOLTAGE
CONTROLLED
OSCILLATOR
PHASE
DETECTOR
LOOP
FILTER
CGMVCLK
PLL ANALOG
CGMINT
(TO SIM)
AUTOMATIC
MODE
CONTROL
LOCK
DETECTOR
INTERRUPT
CONTROL
LOCK
AUTO
ACQ
PLLIE
PLLF
MUL11–MUL0
CGMVDV
FREQUENCY
DIVIDER
Figure 4-1. CGM Block Diagram
Data Sheet
80
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Clock Generator Module (CGM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Functional Description
4.3.1 Crystal Oscillator Circuit
The crystal oscillator circuit consists of an inverting amplifier and an external
crystal. The OSC1 pin is the input to the amplifier and the OSC2 pin is the output.
The SIMOSCEN signal from the system integration module (SIM) or the
OSCENINSTOP bit in the CONFIG register enable the crystal oscillator circuit.
The CGMXCLK signal is the output of the crystal oscillator circuit and runs at a rate
equal to the crystal frequency. CGMXCLK is then buffered to produce CGMRCLK,
the PLL reference clock.
CGMXCLK can be used by other modules which require precise timing for
operation. The duty cycle of CGMXCLK is not guaranteed to be 50% and depends
on external factors, including the crystal and related external components. An
externally generated clock also can feed the OSC1 pin of the crystal oscillator
circuit. Connect the external clock to the OSC1 pin and let the OSC2 pin float.
4.3.2 Phase-Locked Loop Circuit (PLL)
The PLL is a frequency generator that can operate in either acquisition mode or
tracking mode, depending on the accuracy of the output frequency. The PLL can
change between acquisition and tracking modes either automatically or manually.
4.3.3 PLL Circuits
The PLL consists of these circuits:
•
•
•
•
•
Voltage-controlled oscillator (VCO)
Modulo VCO frequency divider
Phase detector
Loop filter
Lock detector
The operating range of the VCO is programmable for a wide range of frequencies
and for maximum immunity to external noise, including supply and CGMXFC noise.
The VCO frequency is bound to a range from roughly one-half to twice the
center-of-range frequency, fVRS. Modulating the voltage on the CGMXFC pin
changes the frequency within this range. By design, fVRS is equal to the nominal
center-of-range frequency, fNOM, (71.4 kHz) times a linear factor, L, and a
power-of-two factor, E, or (L × 2E)fNOM
.
CGMRCLK is the PLL reference clock, a buffered version of CGMXCLK.
CGMRCLK runs at a frequency, fRCLK. The VCO’s output clock, CGMVCLK,
running at a frequency, fVCLK, is fed back through a programmable modulo divider.
The modulo divider reduces the VCO clock by a factor, N. The dividers output is
the VCO feedback clock, CGMVDV, running at a frequency, fVDV = fVCLK/(N). (For
more information, see 4.3.6 Programming the PLL.)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
81
MOTOROLA
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
The phase detector then compares the VCO feedback clock, CGMVDV, with the
final reference clock, CGMRDV. A correction pulse is generated based on the
phase difference between the two signals. The loop filter then slightly alters the DC
voltage on the external capacitor connected to CGMXFC based on the width and
direction of the correction pulse. The filter can make fast or slow corrections
depending on its mode, described in 4.3.4 Acquisition and Tracking Modes. The
value of the external capacitor and the reference frequency determines the speed
of the corrections and the stability of the PLL.
The lock detector compares the frequencies of the VCO feedback clock, CGMVDV,
and the reference clock, CGMRCLK. Therefore, the speed of the lock detector is
directly proportional to the reference frequency, fRCLK. The circuit determines the
mode of the PLL and the lock condition based on this comparison.
4.3.4 Acquisition and Tracking Modes
The PLL filter is manually or automatically configurable into one of two operating
modes:
•
Acquisition mode — In acquisition mode, the filter can make large frequency
corrections to the VCO. This mode is used at PLL start up or when the PLL
has suffered a severe noise hit and the VCO frequency is far off the desired
frequency. When in acquisition mode, the ACQ bit is clear in the PLL
bandwidth control register. (See 4.5.2 PLL Bandwidth Control Register.)
•
Tracking mode — In tracking mode, the filter makes only small corrections
to the frequency of the VCO. PLL jitter is much lower in tracking mode, but
the response to noise is also slower. The PLL enters tracking mode when
the VCO frequency is nearly correct, such as when the PLL is selected as
the base clock source. (See 4.3.8 Base Clock Selector Circuit.) The PLL
is automatically in tracking mode when not in acquisition mode or when the
ACQ bit is set.
4.3.5 Manual and Automatic PLL Bandwidth Modes
The PLL can change the bandwidth or operational mode of the loop filter manually
or automatically. Automatic mode is recommended for most users.
In automatic bandwidth control mode (AUTO = 1), the lock detector automatically
switches between acquisition and tracking modes. Automatic bandwidth control
mode also is used to determine when the VCO clock, CGMVCLK, is safe to use as
the source for the base clock, CGMOUT. (See 4.5.2 PLL Bandwidth Control
Register.) If PLL interrupts are enabled, the software can wait for a PLL interrupt
request and then check the LOCK bit. If interrupts are disabled, software can poll
the LOCK bit continuously (for example, during PLL start up) or at periodic
intervals. In either case, when the LOCK bit is set, the VCO clock is safe to use as
the source for the base clock. (See 4.3.8 Base Clock Selector Circuit.) If the VCO
is selected as the source for the base clock and the LOCK bit is clear, the PLL has
suffered a severe noise hit and the software must take appropriate action,
Data Sheet
82
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Clock Generator Module (CGM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Functional Description
depending on the application. (See 4.6 Interrupts for information and precautions
on using interrupts.)
The following conditions apply when the PLL is in automatic bandwidth control
mode:
•
The ACQ bit (See 4.5.2 PLL Bandwidth Control Register.) is a read-only
indicator of the mode of the filter. (See 4.3.4 Acquisition and Tracking
Modes.)
•
The ACQ bit is set when the VCO frequency is within a certain tolerance and
is cleared when the VCO frequency is out of a certain tolerance. (See 4.8
Acquisition/Lock Time Specifications for more information.)
•
•
The LOCK bit is a read-only indicator of the locked state of the PLL.
The LOCK bit is set when the VCO frequency is within a certain tolerance
and is cleared when the VCO frequency is out of a certain tolerance. (See
4.8 Acquisition/Lock Time Specifications for more information.)
•
CPU interrupts can occur if enabled (PLLIE = 1) when the PLL’s lock
condition changes, toggling the LOCK bit. (See 4.5.1 PLL Control
Register.)
The PLL also may operate in manual mode (AUTO = 0). Manual mode is used by
systems that do not require an indicator of the lock condition for proper operation.
Such systems typically operate well below fBUSMAX
.
The following conditions apply when in manual mode:
•
•
ACQ is a writable control bit that controls the mode of the filter. Before
turning on the PLL in manual mode, the ACQ bit must be clear.
Before entering tracking mode (ACQ = 1), software must wait a given time,
tACQ (See 4.8 Acquisition/Lock Time Specifications.), after turning on the
PLL by setting PLLON in the PLL control register (PCTL).
•
Software must wait a given time, tAL, after entering tracking mode before
selecting the PLL as the clock source to CGMOUT (BCS = 1).
•
•
The LOCK bit is disabled.
CPU interrupts from the CGM are disabled.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
83
MOTOROLA
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
4.3.6 Programming the PLL
Use the following procedure to program the PLL. For reference, the variables used
and their meaning are shown in Table 4-1.
Table 4-1. Variable Definitions
Variable
Definition
Desired bus clock frequency
fBUSDES
fVCLKDES
fRCLK
fVCLK
fBUS
Desired VCO clock frequency
Chosen reference crystal frequency
Calculated VCO clock frequency
Calculated bus clock frequency
Nominal VCO center frequency
Programmed VCO center frequency
fNOM
fVRS
NOTE:
The round function in the following equations means that the real number should
be rounded to the nearest integer number.
1. Choose the desired bus frequency, fBUSDES
.
2. Calculate the desired VCO frequency (four times the desired bus
frequency).
fVCLKDES = 4 x fBUSDES
3. Choose a practical PLL (crystal) reference frequency, fRCLK. Typically, the
reference crystal is 1–8 MHz.
Frequency errors to the PLL are corrected at a rate of fRCLK
.
For stability and lock time reduction, this rate must be as fast as possible.
The VCO frequency must be an integer multiple of this rate. The relationship
between the VCO frequency, fVCLK, and the reference frequency, fRCLK, is:
fVCLK = (N) (fRCLK)
N, the range multiplier, must be an integer.
In cases where desired bus frequency has some tolerance, choose fRCLK to
a value determined either by other module requirements (such as modules
which are clocked by CGMXCLK), cost requirements, or ideally, as high as
the specified range allows. See Section 21. Electrical Specifications.
After choosing N, the actual bus frequency can be determined using
equation in 2 above.
4. Select a VCO frequency multiplier, N.
f
VCLKDES
-------------------------
N = round
f
RCLK
Data Sheet
84
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Clock Generator Module (CGM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Functional Description
5. Calculate and verify the adequacy of the VCO and bus frequencies fVCLK
and fBUS
.
f
= (N) × f
= (f
VCLK
RCLK
f
) ⁄ 4
VCLK
BUS
6. Select the VCO’s power-of-two range multiplier E, according to Table 4-2.
Table 4-2. Power-of-Two Range Selectors
Frequency Range
E
0
1
0 < fVCLK ≤ 8 MHz
8 MHz< fVCLK ≤ 16 MHz
16 MHz< fVCLK ≤ 32 MHz
2(1)
1. Do not program E to a value of 3.
7. Select a VCO linear range multiplier, L, where fNOM = 71.4 kHz
fVCLK
L = Round
2E x fNOM
8. Calculate and verify the adequacy of the VCO programmed center-of-range
frequency, fVRS. The center-of-range frequency is the midpoint between the
minimum and maximum frequencies attainable by the PLL.
f
VRS = (L x 2E) fNOM
9. For proper operation,
E
f
× 2
NOM
--------------------------
≤
VCLK
f
– f
VRS
2
10. Verify the choice of N, E, and L by comparing fVCLK to fVRS and fVCLKDES
For proper operation, fVCLK must be within the application’s tolerance of
.
f
VCLKDES, and fVRS must be as close as possible to fVCLK.
NOTE:
Exceeding the recommended maximum bus frequency or VCO frequency can
crash the MCU.
11. Program the PLL registers accordingly:
a. In the VPR bits of the PLL control register (PCTL), program the binary
equivalent of E.
b. In the PLL multiplier select register low (PMSL) and the PLL multiplier
select register high (PMSH), program the binary equivalent of N. If
using a 1–8 MHz reference, the PMSL register must be reprogrammed
from the reset value before enabling the PLL.
c. In the PLL VCO range select register (PMRS), program the binary
coded equivalent of L.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
85
MOTOROLA
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Table 4-3 provides numeric examples (register values are in hexadecimal
notation):
Table 4-3. Numeric Example
fBUS
fRCLK
N
E
0
0
0
1
1
1
2
2
2
L
500 kHz
1.25 MHz
2.0 MHz
2.5 MHz
3.0 MHz
4.0 MHz
5.0 MHz
7.0 MHz
8.0 MHz
1 MHz
1 MHz
1 MHz
1 MHz
1 MHz
1 MHz
1 MHz
1 MHz
1 MHz
002
005
008
00A
00C
010
014
01C
020
1B
45
70
45
53
70
46
62
70
4.3.7 Special Programming Exceptions
The programming method described in 4.3.6 Programming the PLL does not
account for two possible exceptions. A value of 0 for N or L is meaningless when
used in the equations given. To account for these exceptions:
•
•
A 0 value for N is interpreted exactly the same as a value of 1.
A 0 value for L disables the PLL and prevents its selection as the source for
the base clock.
See 4.3.8 Base Clock Selector Circuit.
4.3.8 Base Clock Selector Circuit
This circuit is used to select either the crystal clock, CGMXCLK, or the VCO clock,
CGMVCLK, as the source of the base clock, CGMOUT. The two input clocks go
through a transition control circuit that waits up to three CGMXCLK cycles and
three CGMVCLK cycles to change from one clock source to the other. During this
time, CGMOUT is held in stasis. The output of the transition control circuit is then
divided by two to correct the duty cycle. Therefore, the bus clock frequency, which
is one-half of the base clock frequency, is one-fourth the frequency of the selected
clock (CGMXCLK or CGMVCLK).
The BCS bit in the PLL control register (PCTL) selects which clock drives
CGMOUT. The VCO clock cannot be selected as the base clock source if the PLL
is not turned on. The PLL cannot be turned off if the VCO clock is selected. The
PLL cannot be turned on or off simultaneously with the selection or deselection of
the VCO clock. The VCO clock also cannot be selected as the base clock source
if the factor L is programmed to a 0. This value would set up a condition
inconsistent with the operation of the PLL, so that the PLL would be disabled and
the crystal clock would be forced as the source of the base clock.
Data Sheet
86
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Clock Generator Module (CGM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Functional Description
4.3.9 CGM External Connections
In its typical configuration, the CGM requires external components. Five of these
are for the crystal oscillator and two or four are for the PLL.
The crystal oscillator is normally connected in a Pierce oscillator configuration, as
shown in Figure 4-2. Figure 4-2 shows only the logical representation of the
internal components and may not represent actual circuitry. The oscillator
configuration uses five components:
•
•
•
•
•
Crystal, X1
Fixed capacitor, C1
Tuning capacitor, C2 (can also be a fixed capacitor)
Feedback resistor, RB
Series resistor, RS
The series resistor (RS) is included in the diagram to follow strict Pierce oscillator
guidelines. Refer to the crystal manufacturer’s data for more information regarding
values for C1 and C2.
Figure 4-2 also shows the external components for the PLL:
•
•
Bypass capacitor, CBYP
Filter network
Routing should be done with great care to minimize signal cross talk and noise.
SIMOSCEN
OSCENINSTOP
(FROM CONFIG)
CGMXCLK
CGMXFC
VSSA
OSC1
OSC2
VDDA
VDD
RB
RF1
CBYP
CF2
RS
CF1
X1
C1
C2
Note: Filter network in box can be replaced with a single capacitor, but will degrade stability.
Figure 4-2. CGM External Connections
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
87
MOTOROLA
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
4.4 I/O Signals
The following paragraphs describe the CGM I/O signals.
4.4.1 Crystal Amplifier Input Pin (OSC1)
The OSC1 pin is an input to the crystal oscillator amplifier.
4.4.2 Crystal Amplifier Output Pin (OSC2)
The OSC2 pin is the output of the crystal oscillator inverting amplifier.
4.4.3 External Filter Capacitor Pin (CGMXFC)
The CGMXFC pin is required by the loop filter to filter out phase corrections. An
external filter network is connected to this pin. (See Figure 4-2.)
NOTE:
To prevent noise problems, the filter network should be placed as close to the
CGMXFC pin as possible, with minimum routing distances and no routing of other
signals across the network.
4.4.4 PLL Analog Power Pin (VDDA
)
VDDA is a power pin used by the analog portions of the PLL. Connect the VDDA pin
to the same voltage potential as the VDD pin.
NOTE:
Route VDDA carefully for maximum noise immunity and place bypass capacitors as
close as possible to the package.
4.4.5 PLL Analog Ground Pin (VSSA
)
VSSA is a ground pin used by the analog portions of the PLL. Connect the VSSA pin
to the same voltage potential as the VSS pin.
NOTE:
Route VSSA carefully for maximum noise immunity and place bypass capacitors as
close as possible to the package.
4.4.6 Oscillator Enable Signal (SIMOSCEN)
The SIMOSCEN signal comes from the system integration module (SIM) and
enables the oscillator and PLL.
4.4.7 Oscillator Enable in Stop Mode Bit (OSCENINSTOP)
OSCENINSTOP is a bit in the CONFIG2 register that enables the oscillator to
continue operating during stop mode. If this bit is set, the oscillator continues
running during stop mode. If this bit is not set (default), the oscillator is controlled
by the SIMOSCEN signal which will disable the oscillator during stop mode.
Data Sheet
88
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Clock Generator Module (CGM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
CGM Registers
4.4.8 Crystal Output Frequency Signal (CGMXCLK)
CGMXCLK is the crystal oscillator output signal. It runs at the full speed of the
crystal (fXCLK) and comes directly from the crystal oscillator circuit. Figure 4-2
shows only the logical relation of CGMXCLK to OSC1 and OSC2 and may not
represent the actual circuitry. The duty cycle of CGMXCLK is unknown and may
depend on the crystal and other external factors. Also, the frequency and amplitude
of CGMXCLK can be unstable at start up.
4.4.9 CGM Base Clock Output (CGMOUT)
CGMOUT is the clock output of the CGM. This signal goes to the SIM, which
generates the MCU clocks. CGMOUT is a 50 percent duty cycle clock running at
twice the bus frequency. CGMOUT is software programmable to be either the
oscillator output, CGMXCLK, divided by two or the VCO clock, CGMVCLK, divided
by two.
4.4.10 CGM CPU Interrupt (CGMINT)
CGMINT is the interrupt signal generated by the PLL lock detector.
4.5 CGM Registers
These registers control and monitor operation of the CGM:
•
•
•
•
•
PLL control register (PCTL)
(See 4.5.1 PLL Control Register.)
PLL bandwidth control register (PBWC)
(See 4.5.2 PLL Bandwidth Control Register.)
PLL multiplier select register high (PMSH)
(See 4.5.3 PLL Multiplier Select Register High.)
PLL multiplier select register low (PMSL)
(See 4.5.4 PLL Multiplier Select Register Low.)
PLL VCO range select register (PMRS)
(See 4.5.5 PLL VCO Range Select Register.)
Figure 4-3 is a summary of the CGM registers.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
89
MOTOROLA
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Addr.
Register Name
Bit 7
PLLIE
0
6
5
PLLON
1
4
3
2
1
Bit 0
Read:
PLLF
PLL Control Register
BCS
R
R
VPR1
VPR0
$0036
(PCTL) Write:
See page 90.
Reset:
Read:
0
0
0
0
0
0
0
0
0
0
LOCK
PLL Bandwidth Control Reg-
AUTO
ACQ
R
$0037
$0038
ister (PBWC) Write:
See page 92.
Reset:
0
0
0
0
0
0
0
0
0
0
0
0
Read:
PLL Multiplier Select High
MUL11
MUL10
MUL9
MUL8
Register (PMSH) Write:
See page 93.
Reset:
0
0
0
0
0
MUL3
0
0
0
0
Read:
PLL Multiplier Select Low
MUL7
0
MUL6
1
MUL5
0
MUL4
0
MUL2
MUL1
MUL0
$0039
Register (PMSL) Write:
See page 94.
Reset:
0
0
0
Read:
PLL VCO Select Range
VRS7
VRS6
VRS5
VRS4
VRS3
0
VRS2
VRS1
VRS0
$003A
$003B
NOTES:
Register (PMRS) Write:
See page 94.
Reset:
0
0
1
0
0
0
0
0
0
R
0
0
R
0
0
R
1
Read:
Reserved Register Write:
Reset:
R
0
0
0
0
0
= Unimplemented
R
= Reserved
1. When AUTO = 0, PLLIE is forced clear and is read-only.
2. When AUTO = 0, PLLF and LOCK read as clear.
3. When AUTO = 1, ACQ is read-only.
4. When PLLON = 0 or VRS7:VRS0 = $0, BCS is forced clear and is read-only.
5. When PLLON = 1, the PLL programming register is read-only.
6. When BCS = 1, PLLON is forced set and is read-only.
Figure 4-3. CGM I/O Register Summary
4.5.1 PLL Control Register
The PLL control register (PCTL) contains the interrupt enable and flag bits, the
on/off switch, the base clock selector bit, and the VCO power-of-two range selector
bits.
Address:
$0036
Bit 7
6
5
PLLON
1
4
BCS
0
3
2
1
VPR1
0
Bit 0
VPR0
0
Read:
Write:
Reset:
PLLF
PLLIE
0
R
R
0
0
0
= Unimplemented
R
= Reserved
Figure 4-4. PLL Control Register (PCTL)
Data Sheet
90
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Clock Generator Module (CGM) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
CGM Registers
PLLIE — PLL Interrupt Enable Bit
This read/write bit enables the PLL to generate an interrupt request when the
LOCK bit toggles, setting the PLL flag, PLLF. When the AUTO bit in the PLL
bandwidth control register (PBWC) is clear, PLLIE cannot be written and reads
as 0. Reset clears the PLLIE bit.
1 = PLL interrupts enabled
0 = PLL interrupts disabled
PLLF — PLL Interrupt Flag Bit
This read-only bit is set whenever the LOCK bit toggles. PLLF generates an
interrupt request if the PLLIE bit also is set. PLLF always reads as 0 when the
AUTO bit in the PLL bandwidth control register (PBWC) is clear. Clear the PLLF
bit by reading the PLL control register. Reset clears the PLLF bit.
1 = Change in lock condition
0 = No change in lock condition
NOTE:
Do not inadvertently clear the PLLF bit. Any read or read-modify-write operation on
the PLL control register clears the PLLF bit.
PLLON — PLL On Bit
This read/write bit activates the PLL and enables the VCO clock, CGMVCLK.
PLLON cannot be cleared if the VCO clock is driving the base clock, CGMOUT
(BCS = 1). (See 4.3.8 Base Clock Selector Circuit.) Reset sets this bit so that
the loop can stabilize as the MCU is powering up.
1 = PLL on
0 = PLL off
BCS — Base Clock Select Bit
This read/write bit selects either the crystal oscillator output, CGMXCLK, or the
VCO clock, CGMVCLK, as the source of the CGM output, CGMOUT. CGMOUT
frequency is one-half the frequency of the selected clock. BCS cannot be set
while the PLLON bit is clear. After toggling BCS, it may take up to three
CGMXCLK and three CGMVCLK cycles to complete the transition from one
source clock to the other. During the transition, CGMOUT is held in stasis. (See
4.3.8 Base Clock Selector Circuit.) Reset clears the BCS bit.
1 = CGMVCLK divided by two drives CGMOUT
0 = CGMXCLK divided by two drives CGMOUT
NOTE:
PLLON and BCS have built-in protection that prevents the base clock selector
circuit from selecting the VCO clock as the source of the base clock if the PLL is
off. Therefore, PLLON cannot be cleared when BCS is set, and BCS cannot be set
when PLLON is clear. If the PLL is off (PLLON = 0), selecting CGMVCLK requires
two writes to the PLL control register. (See 4.3.8 Base Clock Selector Circuit.).
VPR1 and VPR0 — VCO Power-of-Two Range Select Bits
These read/write bits control the VCO’s hardware power-of-two range multiplier
E that, in conjunction with L controls the hardware center-of-range frequency,
f
VRS. VPR1:VPR0 cannot be written when the PLLON bit is set. Reset clears
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
91
MOTOROLA
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
these bits. (See 4.3.3 PLL Circuits, 4.3.6 Programming the PLL, and 4.5.5
PLL VCO Range Select Register.)
Table 4-4. VPR1 and VPR0 Programming
VCO Power-of-Two
Range Multiplier
VPR1 and VPR0
E
00
01
10
0
1
1
2
4
2(1)
1. Do not program E to a value of 3.
NOTE:
Verify that the value of the VPR1 and VPR0 bits in the PCTL register are
appropriate for the given reference and VCO clock frequencies before enabling the
PLL. See 4.3.6 Programming the PLL for detailed instructions on selecting the
proper value for these control bits.
4.5.2 PLL Bandwidth Control Register
The PLL bandwidth control register (PBWC):
•
•
•
Selects automatic or manual (software-controlled) bandwidth control mode
Indicates when the PLL is locked
In automatic bandwidth control mode, indicates when the PLL is in
acquisition or tracking mode
•
In manual operation, forces the PLL into acquisition or tracking mode
Address:
$0037
Bit 7
6
5
ACQ
0
4
0
3
0
2
0
1
0
Bit 0
R
Read:
Write:
Reset:
LOCK
AUTO
0
0
0
0
0
0
0
= Unimplemented
R
= Reserved
Figure 4-5. PLL Bandwidth Control Register (PBWC)
AUTO — Automatic Bandwidth Control Bit
This read/write bit selects automatic or manual bandwidth control. When
initializing the PLL for manual operation (AUTO = 0), clear the ACQ bit before
turning on the PLL. Reset clears the AUTO bit.
1 = Automatic bandwidth control
0 = Manual bandwidth control
LOCK — Lock Indicator Bit
When the AUTO bit is set, LOCK is a read-only bit that becomes set when the
VCO clock, CGMVCLK, is locked (running at the programmed frequency).
Data Sheet
92
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Clock Generator Module (CGM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
CGM Registers
When the AUTO bit is clear, LOCK reads as 0 and has no meaning. The write
one function of this bit is reserved for test, so this bit must always be written a 0.
Reset clears the LOCK bit.
1 = VCO frequency correct or locked
0 = VCO frequency incorrect or unlocked
ACQ — Acquisition Mode Bit
When the AUTO bit is set, ACQ is a read-only bit that indicates whether the PLL
is in acquisition mode or tracking mode. When the AUTO bit is clear, ACQ is a
read/write bit that controls whether the PLL is in acquisition or tracking mode.
In automatic bandwidth control mode (AUTO = 1), the last-written value from
manual operation is stored in a temporary location and is recovered when
manual operation resumes. Reset clears this bit, enabling acquisition mode.
1 = Tracking mode
0 = Acquisition mode
4.5.3 PLL Multiplier Select Register High
The PLL multiplier select register high (PMSH) contains the programming
information for the high byte of the modulo feedback divider.
Address:
$0038
Bit 7
0
6
0
5
0
4
0
3
MUL11
0
2
MUL10
0
1
MUL9
0
Bit 0
MUL8
0
Read:
Write:
Reset:
0
0
0
0
= Unimplemented
Figure 4-6. PLL Multiplier Select Register High (PMSH)
MUL11–MUL8 — Multiplier Select Bits
These read/write bits control the high byte of the modulo feedback divider that
selects the VCO frequency multiplier N. (See 4.3.3 PLL Circuits and 4.3.6
Programming the PLL.) A value of $0000 in the multiplier select registers
configures the modulo feedback divider the same as a value of $0001. Reset
initializes the registers to $0040 for a default multiply value of 64.
NOTE:
The multiplier select bits have built-in protection such that they cannot be written
when the PLL is on (PLLON = 1).
PMSH[7:4] — Unimplemented Bits
These bits have no function and always read as 0s.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
93
MOTOROLA
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
4.5.4 PLL Multiplier Select Register Low
The PLL multiplier select register low (PMSL) contains the programming
information for the low byte of the modulo feedback divider.
Address:
$0038
Bit 7
6
MUL6
1
5
MUL5
0
4
MUL4
0
3
MUL3
0
2
MUL2
0
1
MUL1
0
Bit 0
MUL0
0
Read:
Write:
Reset:
MUL7
0
Figure 4-7. PLL Multiplier Select Register Low (PMSL)
NOTE:
For applications using 1–8 MHz reference frequencies this register must be
reprogrammed before enabling the PLL. The reset value of this register will cause
applications using 1–8 MHz reference frequencies to become unstable if the PLL
is enabled without programming an appropriate value. The programmed value
must not allow the VCO clock to exceed 32 MHz. See 4.3.6 Programming the PLL
for detailed instructions on choosing the proper value for PMSL.
MUL7–MUL0 — Multiplier Select Bits
These read/write bits control the low byte of the modulo feedback divider that
selects the VCO frequency multiplier, N. (See 4.3.3 PLL Circuits and
4.3.6 Programming the PLL.) MUL7–MUL0 cannot be written when the
PLLON bit in the PCTL is set. A value of $0000 in the multiplier select registers
configures the modulo feedback divider the same as a value of $0001. Reset
initializes the register to $40 for a default multiply value of 64.
NOTE:
The multiplier select bits have built-in protection such that they cannot be written
when the PLL is on (PLLON = 1).
4.5.5 PLL VCO Range Select Register
The PLL VCO range select register (PMRS) contains the programming information
required for the hardware configuration of the VCO.
Address:
$003A
Bit 7
6
VRS6
1
5
VRS5
0
4
VRS4
0
3
VRS3
0
2
VRS2
0
1
VRS1
0
Bit 0
VRS0
0
Read:
Write:
Reset:
VRS7
0
Figure 4-8. PLL VCO Range Select Register (PMRS)
NOTE:
Verify that the value of the PMRS register is appropriate for the given reference and
VCO clock frequencies before enabling the PLL. See 4.3.6 Programming the PLL
for detailed instructions on selecting the proper value for these control bits.
Data Sheet
94
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Clock Generator Module (CGM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Interrupts
VRS7–VRS0 — VCO Range Select Bits
These read/write bits control the hardware center-of-range linear multiplier L
which, in conjunction with E (See 4.3.3 PLL Circuits, 4.3.6 Programming the
PLL, and 4.5.1 PLL Control Register.), controls the hardware center-of-range
frequency, fVRS. VRS7–VRS0 cannot be written when the PLLON bit in the
PCTL is set. (See 4.3.7 Special Programming Exceptions.) A value of $00 in
the VCO range select register disables the PLL and clears the BCS bit in the
PLL control register (PCTL). (See 4.3.8 Base Clock Selector Circuit and
4.3.7 Special Programming Exceptions.). Reset initializes the register to $40
for a default range multiply value of 64.
NOTE:
The VCO range select bits have built-in protection such that they cannot be written
when the PLL is on (PLLON = 1) and such that the VCO clock cannot be selected
as the source of the base clock (BCS = 1) if the VCO range select bits are all clear.
The PLL VCO range select register must be programmed correctly. Incorrect
programming can result in failure of the PLL to achieve lock.
4.6 Interrupts
When the AUTO bit is set in the PLL bandwidth control register (PBWC), the PLL
can generate a CPU interrupt request every time the LOCK bit changes state. The
PLLIE bit in the PLL control register (PCTL) enables CPU interrupts from the PLL.
PLLF, the interrupt flag in the PCTL, becomes set whether interrupts are enabled
or not. When the AUTO bit is clear, CPU interrupts from the PLL are disabled and
PLLF reads as 0.
Software should read the LOCK bit after a PLL interrupt request to see if the
request was due to an entry into lock or an exit from lock. When the PLL enters
lock, the VCO clock, CGMVCLK, divided by two can be selected as the CGMOUT
source by setting BCS in the PCTL. When the PLL exits lock, the VCO clock
frequency is corrupt, and appropriate precautions should be taken. If the
application is not frequency sensitive, interrupts should be disabled to prevent PLL
interrupt service routines from impeding software performance or from exceeding
stack limitations.
NOTE:
Software can select the CGMVCLK divided by two as the CGMOUT source even
if the PLL is not locked (LOCK = 0). Therefore, software should make sure the PLL
is locked before setting the BCS bit.
4.7 Special Modes
4.7.1 Wait Mode
The WAIT instruction puts the MCU in low power-consumption standby modes.
The WAIT instruction does not affect the CGM. Before entering wait mode,
software can disengage and turn off the PLL by clearing the BCS and PLLON bits
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
95
MOTOROLA
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
in the PLL control register (PCTL) to save power. Less power-sensitive
applications can disengage the PLL without turning it off, so that the PLL clock is
immediately available at WAIT exit. This would be the case also when the PLL is
to wake the MCU from wait mode, such as when the PLL is first enabled and
waiting for LOCK or LOCK is lost.
4.7.2 Stop Mode
If the OSCENINSTOP bit in the CONFIG2 register is cleared (default), then the
STOP instruction disables the CGM (oscillator and phase locked loop) and holds
low all CGM outputs (CGMXCLK, CGMOUT, and CGMINT).
If the OSCENINSTOP bit in the CONFIG2 register is set, then the phase locked
loop is shut off but the oscillator will continue to operate in stop mode.
4.7.3 CGM During Break Interrupts
The system integration module (SIM) controls whether status bits in other modules
can be cleared during the break state. The BCFE bit in the SIM break flag control
register (SBFCR) enables software to clear status bits during the break state. (See
15.7.3 Break Flag Control Register.)
To allow software to clear status bits during a break interrupt, write a 1 to the BCFE
bit. If a status bit is cleared during the break state, it remains cleared when the MCU
exits the break state.
To protect the PLLF bit during the break state, write a 0 to the BCFE bit. With BCFE
at 0 (its default state), software can read and write the PLL control register during
the break state without affecting the PLLF bit.
4.8 Acquisition/Lock Time Specifications
The acquisition and lock times of the PLL are, in many applications, the most
critical PLL design parameters. Proper design and use of the PLL ensures the
highest stability and lowest acquisition/lock times.
4.8.1 Acquisition/Lock Time Definitions
Typical control systems refer to the acquisition time or lock time as the reaction
time, within specified tolerances, of the system to a step input. In a PLL, the step
input occurs when the PLL is turned on or when it suffers a noise hit. The tolerance
is usually specified as a percent of the step input or when the output settles to the
desired value plus or minus a percent of the frequency change. Therefore, the
reaction time is constant in this definition, regardless of the size of the step input.
For example, consider a system with a 5 percent acquisition time tolerance. If a
command instructs the system to change from 0 Hz to 1 MHz, the acquisition time
is the time taken for the frequency to reach 1 MHz ±50 kHz. Fifty kHz = 5% of the
1-MHz step input. If the system is operating at 1 MHz and suffers a –100-kHz noise
Data Sheet
96
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Clock Generator Module (CGM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Acquisition/Lock Time Specifications
hit, the acquisition time is the time taken to return from 900 kHz to 1 MHz ±5 kHz.
Five kHz = 5% of the 100-kHz step input.
Other systems refer to acquisition and lock times as the time the system takes to
reduce the error between the actual output and the desired output to within
specified tolerances. Therefore, the acquisition or lock time varies according to the
original error in the output. Minor errors may not even be registered. Typical PLL
applications prefer to use this definition because the system requires the output
frequency to be within a certain tolerance of the desired frequency regardless of
the size of the initial error.
4.8.2 Parametric Influences on Reaction Time
Acquisition and lock times are designed to be as short as possible while still
providing the highest possible stability. These reaction times are not constant,
however. Many factors directly and indirectly affect the acquisition time.
The most critical parameter which affects the reaction times of the PLL is the
reference frequency, fRCLK. This frequency is the input to the phase detector
and controls how often the PLL makes corrections. For stability, the corrections
must be small compared to the desired frequency, so several corrections are
required to reduce the frequency error. Therefore, the slower the reference the
longer it takes to make these corrections. This parameter is under user control via
the choice of crystal frequency fXCLK. (See 4.3.3 PLL Circuits and 4.3.6
Programming the PLL.)
Another critical parameter is the external filter network. The PLL modifies the
voltage on the VCO by adding or subtracting charge from capacitors in this
network. Therefore, the rate at which the voltage changes for a given frequency
error (thus change in charge) is proportional to the capacitance. The size of the
capacitor also is related to the stability of the PLL. If the capacitor is too small, the
PLL cannot make small enough adjustments to the voltage and the system cannot
lock. If the capacitor is too large, the PLL may not be able to adjust the voltage in
a reasonable time. (See 4.8.3 Choosing a Filter.)
Also important is the operating voltage potential applied to VDDA. The power supply
potential alters the characteristics of the PLL. A fixed value is best. Variable
supplies, such as batteries, are acceptable if they vary within a known range at very
slow speeds. Noise on the power supply is not acceptable, because it causes small
frequency errors which continually change the acquisition time of the PLL.
Temperature and processing also can affect acquisition time because the electrical
characteristics of the PLL change. The part operates as specified as long as these
influences stay within the specified limits. External factors, however, can cause
drastic changes in the operation of the PLL. These factors include noise injected
into the PLL through the filter capacitor, filter capacitor leakage, stray impedances
on the circuit board, and even humidity or circuit board contamination.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
97
MOTOROLA
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
4.8.3 Choosing a Filter
As described in 4.8.2 Parametric Influences on Reaction Time, the external filter
network is critical to the stability and reaction time of the PLL. The PLL is also
dependent on reference frequency and supply voltage.
Figure 4-9 shows two types of filter circuits. In low-cost applications, where stability
and reaction time of the PLL are not critical, the three component filter network
shown in Figure 4-9 (B) can be replaced by a single capacitor, CF, as shown in
shown in Figure 4-9 (A). Refer to Table 4-5 for recommended filter components at
various reference frequencies. For reference frequencies between the values
listed in the table, extrapolate to the nearest common capacitor value. In general,
a slightly larger capacitor provides more stability at the expense of increased lock
time.
CGMXFC
CGMXFC
RF1
CF2
CF
CF1
VSSA
VSSA
(A)
(B)
Figure 4-9. PLL Filter
Table 4-5. Example Filter Component Values
fRCLK
CF1
CF2
RF1
CF
1 MHz
2 MHz
3 MHz
4 MHz
5 MHz
6 MHz
7 MHz
8 MHz
8.2 nF
4.7 nF
3.3 nF
2.2 nF
1.8 nF
1.5 nF
1.2 nF
1 nF
820 pF
470 pF
330 pF
220 pF
180 pF
150 pF
120 pF
100 pF
2k
2k
2k
2k
2k
2k
2k
2k
18 nF
6.8 nF
5.6 nF
4.7 nF
3.9 nF
3.3 nF
2.7 nF
2.2 nF
Data Sheet
98
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Clock Generator Module (CGM) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 5. Configuration Register (CONFIG)
5.1 Introduction
This section describes the configuration registers, CONFIG1 and CONFIG2. The
configuration registers enable or disable these options:
•
•
•
•
•
•
•
•
•
Stop mode recovery time (32 CGMXCLK cycles or 4096 CGMXCLK cycles)
COP timeout period (218 – 24 or 213 – 24 COPCLK cycles)
STOP instruction
Computer operating properly module (COP)
Low-voltage inhibit (LVI) module control and voltage trip point selection
Enable/disable the oscillator (OSC) during stop mode
Enable/disable an extra divide by 128 prescaler in timebase module
Enable for Motorola scalable controller area network (MSCAN)
Selectable clockout (MCLK) feature with divide by 1, 2, and 4 of the bus or
crystal frequency
•
Timebase clock select
5.2 Functional Description
The configuration registers are used in the initialization of various options. The
configuration registers can be written once after each reset. All of the configuration
register bits are cleared during reset. Since the various options affect the operation
of the microcontroller unit (MCU), it is recommended that these registers be written
immediately after reset. The configuration registers are located at $001E and
$001F and may be read at anytime.
NOTE:
On a FLASH device, the options except MSCANEN and LVI5OR3 are one-time
writable by the user after each reset. These bits are one-time writable by the user
only after each POR (power-on reset). The CONFIG registers are not in the FLASH
memory but are special registers containing one-time writable latches after each
reset. Upon a reset, the CONFIG registers default to predetermined settings as
shown in Figure 5-1 and Figure 5-2.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
99
MOTOROLA
Configuration Register (CONFIG)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Configuration Register (CONFIG)
Address: $001E
Bit 7
6
MCLKSEL
0
5
MCLK1
0
4
3
2
1
Bit 0
MCLK0 MSCANEN TBMCLKSEL OSCENINSTOP SCIBDSRC
See note
Read:
Write:
Reset:
0
0
0
0
0
1
Note: MSCANEN is only reset via POR (power-on reset).
= Unimplemented
Figure 5-1. Configuration Register 2 (CONFIG2)
MCLKSEL — MCLK Source Select Bit
1 = Crystal frequency
0 = Bus frequency
MCLK1 and MCLK0 — MCLK Output Select Bits
Setting the MCLK1 and MCLK0 bits enables the PTD0/SS pin to be used as a
MCLK output clock. Once configured for MCLK, the PTD data direction register
for PTD0 is used to enable and disable the MCLK output. See Table 5-1 for
MCLK options.
Table 5-1. MCLK Output Select
MCLK1
MCLK0
MCLK Frequency
MCLK not enabled
Clock
0
0
1
1
0
1
0
1
Clock divided by 2
Clock divided by 4
MSCANEN— MSCAN08 Enable Bit
Setting the MSCANEN enables the MSCAN08 module and allows the MSCAN08
to use the PTC0/PTC1 pins. See Section 12. MSCAN08 Controller
(MSCAN08) for a more detailed description of the MSCAN08 operation.
1 = Enables MSCAN08 module
0 = Disables the MSCAN08 module
NOTE:
The MSCANEN bit is cleared by a power-on reset (POR) only. Other resets will
leave this bit unaffected.
TBMCLKSEL— Timebase Clock Select Bit
TBMCLKSEL enables an extra divide-by-128 prescaler in the timebase module.
Setting this bit enables the extra prescaler and clearing this bit disables it. See
Section 17. Timebase Module (TBM) for a more detailed description of the
external clock operation.
1 = Enables extra divide-by-128 prescaler in timebase module
0 = Disables extra divide-by-128 prescaler in timebase module
Data Sheet
100
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Configuration Register (CONFIG)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Configuration Register (CONFIG)
Functional Description
OSCENINSTOP — Oscillator Enable In Stop Mode Bit
OSCENINSTOP, when set, will enable the oscillator to continue to generate
clocks in stop mode. See Section 4. Clock Generator Module (CGM). This
function is used to keep the timebase running while the rest of the MCU stops.
See Section 17. Timebase Module (TBM). When clear, the oscillator will
cease to generate clocks while in stop mode. The default state for this option is
clear, disabling the oscillator in stop mode.
1 = Oscillator enabled during stop mode
0 = Oscillator disabled during stop mode (default)
SCIBDSRC — SCI Baud Rate Clock Source Bit
SCIBDSRC controls the clock source used for the serial communications
interface (SCI). The setting of this bit affects the frequency at which the SCI
operates.See Section 14. Enhanced Serial Communications Interface
(ESCI) Module.
1 = Internal data bus clock used as clock source for SCI (default)
0 = External oscillator used as clock source for SCI
Address: $001F
Bit 7
COPRS
0
6
5
4
3
2
SSREC
0
1
STOP
0
Bit 0
COPD
0
Read:
Write:
Reset:
LVISTOP LVIRSTD LVIPWRD LVI5OR3
See note
0
0
0
Note: LVI5OR3 is only reset via POR (power-on reset).
Figure 5-2. Configuration Register 1 (CONFIG1)
COPRS — COP Rate Select Bit
COPRS selects the COP timeout period. Reset clears COPRS. See Section 6.
Computer Operating Properly (COP) Module
1 = COP timeout period = 213 – 24 COPCLK cycles
0 = COP timeout period = 218 – 24 COPCLK cycles
LVISTOP — LVI Enable in Stop Mode Bit
When the LVIPWRD bit is clear, setting the LVISTOP bit enables the LVI to
operate during stop mode. Reset clears LVISTOP.
1 = LVI enabled during stop mode
0 = LVI disabled during stop mode
LVIRSTD — LVI Reset Disable Bit
LVIRSTD disables the reset signal from the LVI module.
See Section 11. Low-Voltage Inhibit (LVI).
1 = LVI module resets disabled
0 = LVI module resets enabled
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
101
MOTOROLA
Configuration Register (CONFIG)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Configuration Register (CONFIG)
LVIPWRD — LVI Power Disable Bit
LVIPWRD disables the LVI module. See Section 11. Low-Voltage Inhibit
(LVI).
1 = LVI module power disabled
0 = LVI module power enabled
LVI5OR3 — LVI 5-V or 3-V Operating Mode Bit
LVI5OR3 selects the voltage operating mode of the LVI module (see
Section 11. Low-Voltage Inhibit (LVI)). The voltage mode selected for the LVI
should match the operating VDD (see Section 21. Electrical Specifications)
for the LVI’s voltage trip points for each of the modes.
1 = LVI operates in 5-V mode
0 = LVI operates in 3-V mode
NOTE:
NOTE:
The LVI5OR3 bit is cleared by a power-on reset (POR) only. Other resets will leave
this bit unaffected.
SSREC — Short Stop Recovery Bit
SSREC enables the CPU to exit stop mode with a delay of 32 CGMXCLK cycles
instead of a 4096-CGMXCLK cycle delay.
1 = Stop mode recovery after 32 CGMXCLK cycles
0 = Stop mode recovery after 4096 CGMXCLK cycles
Exiting stop mode by any reset will result in the long stop recovery.
The short stop recovery delay can be enabled when using a crystal or resonator
and the OSCENINSTOP bit is set. The short stop recovery delay can be
enabled when an external oscillator is used, regardless of the OSCENINSTOP
setting.
The short stop recovery delay must be disabled when the OSCENINSTOP bit
is clear and a crystal or resonator is used.
STOP — STOP Instruction Enable Bit
STOP enables the STOP instruction.
1 = STOP instruction enabled
0 = STOP instruction treated as illegal opcode
COPD — COP Disable Bit
COPD disables the COP module. See Section 6. Computer Operating
Properly (COP) Module.
1 = COP module disabled
0 = COP module enabled
Data Sheet
102
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Configuration Register (CONFIG)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 6. Computer Operating Properly (COP) Module
6.1 Introduction
The computer operating properly (COP) module contains a free-running counter
that generates a reset if allowed to overflow. The COP module helps software
recover from runaway code. Prevent a COP reset by clearing the COP counter
periodically. The COP module can be disabled through the COPD bit in the
CONFIG register.
6.2 Functional Description
Figure 6-1 shows the structure of the COP module.
CGMXCLK
RESET CIRCUIT
12-BIT SIM COUNTER
RESET STATUS REGISTER
STOP INSTRUCTION
INTERNAL RESET SOURCES
COPCTL WRITE
COP CLOCK
COP MODULE
6-BIT COP COUNTER
COPEN (FROM SIM)
COP DISABLE
(FROM CONFIG)
RESET
CLEAR
COP COUNTER
COPCTL WRITE
COP RATE SEL
(FROM CONFIG)
Figure 6-1. COP Block Diagram
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Computer Operating Properly (COP) Module
Data Sheet
103
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Computer Operating Properly (COP) Module
The COP counter is a free-running 6-bit counter preceded by the 12-bit SIM
counter. If not cleared by software, the COP counter overflows and generates an
asynchronous reset after 218 – 24 or 213 – 24 CGMXCLK cycles, depending on the
state of the COP rate select bit, COPRS, in the configuration register. With a
2
18 – 24 CGMXCLK cycle overflow option, a 4.9152-MHz crystal gives a COP
timeout period of 53.3 ms. Writing any value to location $FFFF before an overflow
occurs prevents a COP reset by clearing the COP counter and stages 12–5 of the
SIM counter.
NOTE:
NOTE:
Service the COP immediately after reset and before entering or after exiting stop
mode to guarantee the maximum time before the first COP counter overflow.
A COP reset pulls the RST pin low for 32 CGMXCLK cycles and sets the COP bit
in the reset status register (RSR).
In monitor mode, the COP is disabled if the RST pin or the IRQ is held at VTST
.
During the break state, VTST on the RST pin disables the COP.
Place COP clearing instructions in the main program and not in an interrupt
subroutine. Such an interrupt subroutine could keep the COP from generating a
reset even while the main program is not working properly.
6.3 I/O Signals
6.3.1 CGMXCLK
The following paragraphs describe the signals shown in Figure 6-1.
CGMXCLK is the crystal oscillator output signal. CGMXCLK frequency is equal to
the crystal frequency.
6.3.2 STOP Instruction
The STOP instruction clears the SIM counter.
6.3.3 COPCTL Write
Writing any value to the COP control register (COPCTL) clears the COP counter
and clears stages 12–5 of the SIM counter. Reading the COP control register
returns the low byte of the reset vector. See 6.4 COP Control Register.
6.3.4 Power-On Reset
The power-on reset (POR) circuit clears the SIM counter 4096 CGMXCLK cycles
after power-up.
Data Sheet
104
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Computer Operating Properly (COP) Module MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Computer Operating Properly (COP) Module
COP Control Register
6.3.5 Internal Reset
An internal reset clears the SIM counter and the COP counter.
6.3.6 COPD (COP Disable)
The COPD signal reflects the state of the COP disable bit (COPD) in the
configuration register. See Section 5. Configuration Register (CONFIG).
6.3.7 COPRS (COP Rate Select)
The COPRS signal reflects the state of the COP rate select bit (COPRS) in the
configuration register. See Section 5. Configuration Register (CONFIG).
6.4 COP Control Register
The COP control register (COPCTL) is located at address $FFFF and overlaps the
reset vector. Writing any value to $FFFF clears the COP counter and starts a new
timeout period. Reading location $FFFF returns the low byte of the reset vector.
Address: $FFFF
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
Low byte of reset vector
Clear COP counter
Unaffected by reset
Figure 6-2. COP Control Register (COPCTL)
6.5 Interrupts
The COP does not generate central processor unit (CPU) interrupt requests.
6.6 Monitor Mode
When monitor mode is entered with VTST on the IRQ pin, the COP is disabled as
long as VTST remains on the IRQ pin or the RST pin. When monitor mode is
entered by having blank reset vectors and not having VTST on the IRQ pin, the COP
is automatically disabled until a POR occurs.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Computer Operating Properly (COP) Module
Data Sheet
105
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Computer Operating Properly (COP) Module
6.7 Low-Power Modes
The WAIT and STOP instructions put the microcontroller unit (MCU) in low
power-consumption standby modes.
6.7.1 Wait Mode
6.7.2 Stop Mode
The COP remains active during wait mode. If COP is enabled, a reset will occur at
COP timeout.
Stop mode turns off the CGMXCLK input to the COP and clears the SIM counter.
Service the COP immediately before entering or after exiting stop mode to ensure
a full COP timeout period after entering or exiting stop mode.
To prevent inadvertently turning off the COP with a STOP instruction, a
configuration option is available that disables the STOP instruction. When the
STOP bit in the configuration register has the STOP instruction disabled, execution
of a STOP instruction results in an illegal opcode reset.
6.8 COP Module During Break Mode
The COP is disabled during a break interrupt when VTST is present on the RST pin.
Data Sheet
106
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Computer Operating Properly (COP) Module MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 7. Central Processor Unit (CPU)
7.1 Introduction
7.2 Features
The M68HC08 CPU (central processor unit) is an enhanced and fully
object-code-compatible version of the M68HC05 CPU. The CPU08 Reference
Manual (Motorola document order number CPU08RM/AD) contains a description
of the CPU instruction set, addressing modes, and architecture.
Features of the CPU include:
•
•
•
•
•
•
•
•
•
•
Object code fully upward-compatible with M68HC05 Family
16-bit stack pointer with stack manipulation instructions
16-bit index register with x-register manipulation instructions
8-MHz CPU internal bus frequency
64-Kbyte program/data memory space
16 addressing modes
Memory-to-memory data moves without using accumulator
Fast 8-bit by 8-bit multiply and 16-bit by 8-bit divide instructions
Enhanced binary-coded decimal (BCD) data handling
Modular architecture with expandable internal bus definition for extension of
addressing range beyond 64 Kbytes
•
Low-power stop and wait modes
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
107
MOTOROLA
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
7.3 CPU Registers
Figure 7-1 shows the five CPU registers. CPU registers are not part of the memory
map.
7
0
0
0
0
ACCUMULATOR (A)
15
15
15
H
X
INDEX REGISTER (H:X)
STACK POINTER (SP)
PROGRAM COUNTER (PC)
CONDITION CODE REGISTER (CCR)
7
0
V
1
1
H
I
N
Z
C
CARRY/BORROW FLAG
ZERO FLAG
NEGATIVE FLAG
INTERRUPT MASK
HALF-CARRY FLAG
TWO’S COMPLEMENT OVERFLOW FLAG
Figure 7-1. CPU Registers
7.3.1 Accumulator
The accumulator is a general-purpose 8-bit register. The CPU uses the
accumulator to hold operands and the results of arithmetic/logic operations.
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
Unaffected by reset
Figure 7-2. Accumulator (A)
Data Sheet
108
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Central Processor Unit (CPU) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
CPU Registers
7.3.2 Index Register
The 16-bit index register allows indexed addressing of a 64-Kbyte memory space.
H is the upper byte of the index register, and X is the lower byte. H:X is the
concatenated 16-bit index register.
In the indexed addressing modes, the CPU uses the contents of the index register
to determine the conditional address of the operand.
The index register can serve also as a temporary data storage location.
Bit
15 14 13 12 11 10
Bit
0
9
0
8
0
7
6
5
4
3
2
1
Read:
Write:
Reset:
0
0
0
0
0
0
X
X
X
X
X
X
X
X
X = Indeterminate
Figure 7-3. Index Register (H:X)
7.3.3 Stack Pointer
The stack pointer is a 16-bit register that contains the address of the next location
on the stack. During a reset, the stack pointer is preset to $00FF. The reset stack
pointer (RSP) instruction sets the least significant byte to $FF and does not affect
the most significant byte. The stack pointer decrements as data is pushed onto the
stack and increments as data is pulled from the stack.
In the stack pointer 8-bit offset and 16-bit offset addressing modes, the stack
pointer can function as an index register to access data on the stack. The CPU
uses the contents of the stack pointer to determine the conditional address of the
operand.
Bit
15 14 13 12 11 10
Bit
0
9
0
8
0
7
1
6
1
5
1
4
1
3
1
2
1
1
1
Read:
Write:
Reset:
0
0
0
0
0
0
1
Figure 7-4. Stack Pointer (SP)
The location of the stack is arbitrary and may be relocated anywhere in
NOTE:
random-access memory (RAM). Moving the SP out of page 0 ($0000 to $00FF)
frees direct address (page 0) space. For correct operation, the stack pointer must
point only to RAM locations.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
109
MOTOROLA
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
7.3.4 Program Counter
The program counter is a 16-bit register that contains the address of the next
instruction or operand to be fetched.
Normally, the program counter automatically increments to the next sequential
memory location every time an instruction or operand is fetched. Jump, branch,
and interrupt operations load the program counter with an address other than that
of the next sequential location.
During reset, the program counter is loaded with the reset vector address located
at $FFFE and $FFFF. The vector address is the address of the first instruction to
be executed after exiting the reset state.
Bit
15 14 13 12 11 10
Bit
0
9
8
7
6
5
4
3
2
1
Read:
Write:
Reset:
Loaded with vector from $FFFE and $FFFF
Figure 7-5. Program Counter (PC)
7.3.5 Condition Code Register
The 8-bit condition code register contains the interrupt mask and five flags that
indicate the results of the instruction just executed. Bits 6 and 5 are set
permanently to 1. The following paragraphs describe the functions of the condition
code register.
Bit 7
V
6
1
1
5
1
1
4
H
X
3
I
2
N
X
1
Z
X
Bit 0
C
Read:
Write:
Reset:
X
1
X
X = Indeterminate
Figure 7-6. Condition Code Register (CCR)
V — Overflow Flag
The CPU sets the overflow flag when a two's complement overflow occurs. The
signed branch instructions BGT, BGE, BLE, and BLT use the overflow flag.
1 = Overflow
0 = No overflow
Data Sheet
110
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Central Processor Unit (CPU)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
CPU Registers
H — Half-Carry Flag
The CPU sets the half-carry flag when a carry occurs between accumulator bits
3 and 4 during an add-without-carry (ADD) or add-with-carry (ADC) operation.
The half-carry flag is required for binary-coded decimal (BCD) arithmetic
operations. The DAA instruction uses the states of the H and C flags to
determine the appropriate correction factor.
1 = Carry between bits 3 and 4
0 = No carry between bits 3 and 4
I — Interrupt Mask
When the interrupt mask is set, all maskable CPU interrupts are disabled. CPU
interrupts are enabled when the interrupt mask is cleared. When a CPU
interrupt occurs, the interrupt mask is set
automatically after the CPU registers are saved on the stack, but before the
interrupt vector is fetched.
1 = Interrupts disabled
0 = Interrupts enabled
NOTE:
To maintain M6805 Family compatibility, the upper byte of the index register (H) is
not stacked automatically. If the interrupt service routine modifies H, then the user
must stack and unstack H using the PSHH and PULH instructions.
After the I bit is cleared, the highest-priority interrupt request is serviced first.
A return-from-interrupt (RTI) instruction pulls the CPU registers from the stack
and restores the interrupt mask from the stack. After any reset, the interrupt
mask is set and can be cleared only by the clear interrupt mask software
instruction (CLI).
N — Negative flag
The CPU sets the negative flag when an arithmetic operation, logic operation,
or data manipulation produces a negative result, setting bit 7 of the result.
1 = Negative result
0 = Non-negative result
Z — Zero flag
The CPU sets the zero flag when an arithmetic operation, logic operation, or
data manipulation produces a result of $00.
1 = Zero result
0 = Non-zero result
C — Carry/Borrow Flag
The CPU sets the carry/borrow flag when an addition operation produces a
carry out of bit 7 of the accumulator or when a subtraction operation requires a
borrow. Some instructions — such as bit test and branch, shift, and rotate —
also clear or set the carry/borrow flag.
1 = Carry out of bit 7
0 = No carry out of bit 7
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
111
MOTOROLA
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
7.4 Arithmetic/Logic Unit (ALU)
The ALU performs the arithmetic and logic operations defined by the instruction
set.
Refer to the CPU08 Reference Manual (Motorola document order number
CPU08RM/AD) for a description of the instructions and addressing modes and
more detail about the architecture of the CPU.
7.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power-consumption standby
modes.
7.5.1 Wait Mode
The WAIT instruction:
•
Clears the interrupt mask (I bit) in the condition code register, enabling
interrupts. After exit from wait mode by interrupt, the I bit remains clear. After
exit by reset, the I bit is set.
•
Disables the CPU clock
7.5.2 Stop Mode
The STOP instruction:
•
Clears the interrupt mask (I bit) in the condition code register, enabling
external interrupts. After exit from stop mode by external interrupt, the I bit
remains clear. After exit by reset, the I bit is set.
•
Disables the CPU clock
After exiting stop mode, the CPU clock begins running after the oscillator
stabilization delay.
7.6 CPU During Break Interrupts
If a break module is present on the MCU, the CPU starts a break interrupt by:
•
•
Loading the instruction register with the SWI instruction
Loading the program counter with $FFFC:$FFFD or with $FEFC:$FEFD in
monitor mode
The break interrupt begins after completion of the CPU instruction in progress. If
the break address register match occurs on the last cycle of a CPU instruction, the
break interrupt begins immediately.
A return-from-interrupt instruction (RTI) in the break routine ends the break
interrupt and returns the MCU to normal operation if the break interrupt has been
deasserted.
Data Sheet
112
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Central Processor Unit (CPU)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Instruction Set Summary
7.7 Instruction Set Summary
Table 7-1 provides a summary of the M68HC08 instruction set.
Table 7-1. Instruction Set Summary (Sheet 1 of 7)
Effect
Source
Form
on CCR
Operation
Description
V H I N Z C
ADC #opr
IMM
DIR
EXT
IX2
A9 ii
B9 dd
C9 hh ll
D9 ee ff
E9 ff
2
3
4
4
3
2
4
5
ADC opr
ADC opr
ADC opr,X
ADC opr,X
ADC ,X
Add with Carry
A ← (A) + (M) + (C)
ꢀ
ꢀ
ꢀ
–
–
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
IX1
IX
SP1
SP2
F9
ADC opr,SP
ADC opr,SP
9EE9 ff
9ED9 ee ff
ADD #opr
ADD opr
ADD opr
ADD opr,X
ADD opr,X
ADD ,X
ADD opr,SP
ADD opr,SP
IMM
DIR
EXT
IX2
IX1
IX
SP1
SP2
AB ii
BB dd
CB hh ll
DB ee ff
EB ff
FB
9EEB ff
9EDB ee ff
2
3
4
4
3
2
4
5
Add without Carry
A ← (A) + (M)
ꢀ
ꢀ
AIS #opr
AIX #opr
Add Immediate Value (Signed) to SP
Add Immediate Value (Signed) to H:X
–
–
–
–
–
–
–
–
–
–
– IMM
– IMM
A7 ii
AF ii
2
2
SP ← (SP) + (16 « M)
H:X ← (H:X) + (16 « M)
AND #opr
AND opr
IMM
DIR
EXT
A4 ii
B4 dd
C4 hh ll
D4 ee ff
E4 ff
2
3
4
4
3
2
4
5
AND opr
AND opr,X
AND opr,X
AND ,X
AND opr,SP
AND opr,SP
IX2
Logical AND
A ← (A) & (M)
0
–
–
–
–
ꢀ
ꢀ
ꢀ
ꢀ
–
IX1
IX
SP1
SP2
F4
9EE4 ff
9ED4 ee ff
ASL opr
ASLA
ASLX
ASL opr,X
ASL ,X
ASL opr,SP
DIR
INH
38 dd
48
4
1
1
4
3
5
Arithmetic Shift Left
(Same as LSL)
INH
58
C
0
ꢀ
ꢀ
IX1
68 ff
78
b7
b7
b0
b0
IX
SP1
9E68 ff
ASR opr
ASRA
ASRX
ASR opr,X
ASR opr,X
ASR opr,SP
DIR
INH
37 dd
47
4
1
1
4
3
5
INH
57
C
Arithmetic Shift Right
ꢀ
–
–
–
–
ꢀ
ꢀ
ꢀ
IX1
67 ff
77
IX
SP1
9E67 ff
BCC rel
Branch if Carry Bit Clear
PC ← (PC) + 2 + rel ? (C) = 0
–
–
–
– REL
24 rr
3
DIR (b0) 11 dd
DIR (b1) 13 dd
DIR (b2) 15 dd
DIR (b3) 17 dd
DIR (b4) 19 dd
DIR (b5) 1B dd
DIR (b6) 1D dd
DIR (b7) 1F dd
4
4
4
4
4
4
4
4
BCLR n, opr
Clear Bit n in M
Mn ← 0
–
–
–
–
–
–
BCS rel
BEQ rel
Branch if Carry Bit Set (Same as BLO)
Branch if Equal
PC ← (PC) + 2 + rel ? (C) = 1
PC ← (PC) + 2 + rel ? (Z) = 1
–
–
–
–
–
–
–
–
–
–
– REL
– REL
25 rr
27 rr
3
3
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Central Processor Unit (CPU)
Data Sheet
113
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Table 7-1. Instruction Set Summary (Sheet 2 of 7)
Effect
Source
Form
on CCR
Operation
Description
V H I N Z C
Branch if Greater Than or Equal To
(Signed Operands)
BGE opr
–
–
–
–
–
–
–
–
–
–
– REL
– REL
90 rr
92 rr
3
PC ← (PC) + 2 + rel ? (N ⊕ V) = 0
Branch if Greater Than (Signed
Operands)
BGT opr
3
3
PC ← (PC) + 2 + rel ? (Z) | (N ⊕ V) = 0
BHCC rel
BHCS rel
BHI rel
Branch if Half Carry Bit Clear
Branch if Half Carry Bit Set
Branch if Higher
PC ← (PC) + 2 + rel ? (H) = 0
PC ← (PC) + 2 + rel ? (H) = 1
PC ← (PC) + 2 + rel ? (C) | (Z) = 0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
– REL
– REL
– REL
28 rr
29 rr
22 rr
3
3
3
Branch if Higher or Same
(Same as BCC)
BHS rel
PC ← (PC) + 2 + rel ? (C) = 0
–
–
–
–
–
– REL
24 rr
BIH rel
BIL rel
Branch if IRQ Pin High
Branch if IRQ Pin Low
PC ← (PC) + 2 + rel ? IRQ = 1
PC ← (PC) + 2 + rel ? IRQ = 0
–
–
–
–
–
–
–
–
–
–
– REL
– REL
2F rr
2E rr
3
3
BIT #opr
BIT opr
IMM
DIR
EXT
A5 ii
B5 dd
C5 hh ll
D5 ee ff
E5 ff
2
3
4
4
3
2
4
5
BIT opr
BIT opr,X
BIT opr,X
BIT ,X
BIT opr,SP
BIT opr,SP
IX2
Bit Test
(A) & (M)
0
–
–
ꢀ
ꢀ
–
IX1
IX
SP1
SP2
F5
9EE5 ff
9ED5 ee ff
Branch if Less Than or Equal To
(Signed Operands)
BLE opr
–
–
–
–
–
– REL
93 rr
3
PC ← (PC) + 2 + rel ? (Z) | (N ⊕ V) = 1
BLO rel
BLS rel
BLT opr
BMC rel
BMI rel
BMS rel
BNE rel
BPL rel
BRA rel
Branch if Lower (Same as BCS)
Branch if Lower or Same
Branch if Less Than (Signed Operands)
Branch if Interrupt Mask Clear
Branch if Minus
PC ← (PC) + 2 + rel ? (C) = 1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
– REL
– REL
– REL
– REL
– REL
– REL
– REL
– REL
– REL
25 rr
23 rr
91 rr
2C rr
2B rr
2D rr
26 rr
2A rr
20 rr
3
3
3
3
3
3
3
3
3
PC ← (PC) + 2 + rel ? (C) | (Z) = 1
PC ← (PC) + 2 + rel ? (N ⊕ V) =1
PC ← (PC) + 2 + rel ? (I) = 0
PC ← (PC) + 2 + rel ? (N) = 1
PC ← (PC) + 2 + rel ? (I) = 1
PC ← (PC) + 2 + rel ? (Z) = 0
PC ← (PC) + 2 + rel ? (N) = 0
PC ← (PC) + 2 + rel
Branch if Interrupt Mask Set
Branch if Not Equal
Branch if Plus
Branch Always
DIR (b0) 01 dd rr
DIR (b1) 03 dd rr
DIR (b2) 05 dd rr
DIR (b3) 07 dd rr
DIR (b4) 09 dd rr
DIR (b5) 0B dd rr
DIR (b6) 0D dd rr
DIR (b7) 0F dd rr
5
5
5
5
5
5
5
5
BRCLR n,opr,rel Branch if Bit n in M Clear
PC ← (PC) + 3 + rel ? (Mn) = 0
PC ← (PC) + 2
–
–
–
–
–
–
–
–
–
–
ꢀ
BRN rel
Branch Never
– REL
21 rr
3
Data Sheet
114
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Central Processor Unit (CPU)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Instruction Set Summary
Table 7-1. Instruction Set Summary (Sheet 3 of 7)
Effect
Source
Form
on CCR
Operation
Description
V H I N Z C
DIR (b0) 00 dd rr
DIR (b1) 02 dd rr
DIR (b2) 04 dd rr
DIR (b3) 06 dd rr
DIR (b4) 08 dd rr
DIR (b5) 0A dd rr
DIR (b6) 0C dd rr
DIR (b7) 0E dd rr
5
5
5
5
5
5
5
5
BRSET n,opr,rel Branch if Bit n in M Set
PC ← (PC) + 3 + rel ? (Mn) = 1
–
–
–
–
–
–
–
–
–
ꢀ
DIR (b0) 10 dd
DIR (b1) 12 dd
DIR (b2) 14 dd
DIR (b3) 16 dd
DIR (b4) 18 dd
DIR (b5) 1A dd
DIR (b6) 1C dd
DIR (b7) 1E dd
4
4
4
4
4
4
4
4
BSET n,opr
BSR rel
Set Bit n in M
Mn ← 1
–
–
PC ← (PC) + 2; push (PCL)
SP ← (SP) – 1; push (PCH)
SP ← (SP) – 1
Branch to Subroutine
–
–
–
–
–
–
–
–
–
–
– REL
AD rr
4
PC ← (PC) + rel
CBEQ opr,rel
PC ← (PC) + 3 + rel ? (A) – (M) = $00
PC ← (PC) + 3 + rel ? (A) – (M) = $00
PC ← (PC) + 3 + rel ? (X) – (M) = $00
PC ← (PC) + 3 + rel ? (A) – (M) = $00
PC ← (PC) + 2 + rel ? (A) – (M) = $00
PC ← (PC) + 4 + rel ? (A) – (M) = $00
DIR
31 dd rr
41 ii rr
51 ii rr
61 ff rr
71 rr
5
4
4
5
4
6
CBEQA #opr,rel
CBEQX #opr,rel
CBEQ opr,X+,rel
CBEQ X+,rel
IMM
IMM
Compare and Branch if Equal
–
IX1+
IX+
CBEQ opr,SP,rel
SP1
9E61 ff rr
CLC
CLI
Clear Carry Bit
C ← 0
I ← 0
–
–
–
–
–
0
–
–
–
–
0 INH
– INH
98
9A
1
2
Clear Interrupt Mask
CLR opr
CLRA
M ← $00
A ← $00
X ← $00
H ← $00
M ← $00
M ← $00
M ← $00
DIR
INH
3F dd
4F
3
1
1
1
3
2
4
CLRX
INH
5F
CLRH
Clear
0
–
–
–
–
0
1
– INH
IX1
IX
SP1
8C
CLR opr,X
CLR ,X
6F ff
7F
CLR opr,SP
9E6F ff
CMP #opr
CMP opr
CMP opr
CMP opr,X
CMP opr,X
CMP ,X
CMP opr,SP
CMP opr,SP
IMM
DIR
EXT
A1 ii
B1 dd
C1 hh ll
D1 ee ff
E1 ff
2
3
4
4
3
2
4
5
IX2
Compare A with M
(A) – (M)
ꢀ
ꢀ
ꢀ
ꢀ
IX1
IX
F1
SP1
SP2
9EE1 ff
9ED1 ee ff
COM opr
COMA
M ← (M) = $FF – (M)
A ← (A) = $FF – (M)
X ← (X) = $FF – (M)
M ← (M) = $FF – (M)
M ← (M) = $FF – (M)
M ← (M) = $FF – (M)
DIR
INH
33 dd
43
4
1
1
4
3
5
COMX
INH
53
Complement (One’s Complement)
Compare H:X with M
0
–
–
–
–
ꢀ
ꢀ
ꢀ
ꢀ
1
COM opr,X
COM ,X
COM opr,SP
IX1
63 ff
73
9E63 ff
IX
SP1
CPHX #opr
CPHX opr
IMM
ꢀ
65 ii ii+1
75 dd
3
4
(H:X) – (M:M + 1)
ꢀ
DIR
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Central Processor Unit (CPU)
Data Sheet
115
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Table 7-1. Instruction Set Summary (Sheet 4 of 7)
Effect
Source
Form
on CCR
Operation
Description
V H I N Z C
CPX #opr
IMM
DIR
EXT
IX2
A3 ii
B3 dd
C3 hh ll
D3 ee ff
E3 ff
2
3
4
4
3
2
4
5
CPX opr
CPX opr
CPX ,X
CPX opr,X
CPX opr,X
CPX opr,SP
CPX opr,SP
Compare X with M
(X) – (M)
(A)10
ꢀ
–
–
ꢀ
ꢀ
ꢀ
IX1
IX
SP1
SP2
F3
9EE3 ff
9ED3 ee ff
DAA
Decimal Adjust A
U
–
–
–
–
–
ꢀ
ꢀ
ꢀ INH
72
2
A ← (A) – 1 or M ← (M) – 1 or X ← (X) – 1
PC ← (PC) + 3 + rel ? (result) ≠ 0
PC ← (PC) + 2 + rel ? (result) ≠ 0
PC ← (PC) + 2 + rel ? (result) ≠ 0
PC ← (PC) + 3 + rel ? (result) ≠ 0
PC ← (PC) + 2 + rel ? (result) ≠ 0
PC ← (PC) + 4 + rel ? (result) ≠ 0
5
3
3
5
4
6
DBNZ opr,rel
DBNZA rel
DBNZX rel
DBNZ opr,X,rel
DBNZ X,rel
DBNZ opr,SP,rel
DIR
INH
3B dd rr
4B rr
Decrement and Branch if Not Zero
–
–
– INH
IX1
5B rr
6B ff rr
7B rr
IX
SP1
9E6B ff rr
DEC opr
DECA
M ← (M) – 1
A ← (A) – 1
X ← (X) – 1
M ← (M) – 1
M ← (M) – 1
M ← (M) – 1
DIR
INH
3A dd
4A
4
1
1
4
3
5
DECX
INH
5A
Decrement
Divide
ꢀ
–
–
–
–
ꢀ
ꢀ
ꢀ
–
DEC opr,X
DEC ,X
DEC opr,SP
IX1
6A ff
7A
9E6A ff
IX
SP1
A ← (H:A)/(X)
H ← Remainder
DIV
–
–
ꢀ INH
52
7
EOR #opr
EOR opr
IMM
DIR
EXT
A8 ii
B8 dd
C8 hh ll
D8 ee ff
E8 ff
2
3
4
4
3
2
4
5
EOR opr
EOR opr,X
EOR opr,X
EOR ,X
EOR opr,SP
EOR opr,SP
IX2
Exclusive OR M with A
0
–
–
–
–
ꢀ
ꢀ
ꢀ
ꢀ
–
A ← (A ⊕ M)
IX1
IX
SP1
SP2
F8
9EE8 ff
9ED8 ee ff
INC opr
INCA
INCX
INC opr,X
INC ,X
INC opr,SP
M ← (M) + 1
A ← (A) + 1
X ← (X) + 1
M ← (M) + 1
M ← (M) + 1
M ← (M) + 1
DIR
INH
3C dd
4C
4
1
1
4
3
5
INH
5C
Increment
ꢀ
–
IX1
6C ff
7C
IX
SP1
9E6C ff
JMP opr
JMP opr
JMP opr,X
JMP opr,X
JMP ,X
DIR
EXT
– IX2
IX1
BC dd
CC hh ll
DC ee ff
EC ff
2
3
4
3
2
Jump
PC ← Jump Address
–
–
–
–
–
–
–
–
–
–
IX
FC
JSR opr
JSR opr
JSR opr,X
JSR opr,X
JSR ,X
DIR
EXT
– IX2
IX1
BD dd
CD hh ll
DD ee ff
ED ff
4
5
6
5
4
PC ← (PC) + n (n = 1, 2, or 3)
Push (PCL); SP ← (SP) – 1
Push (PCH); SP ← (SP) – 1
PC ← Unconditional Address
Jump to Subroutine
IX
FD
LDA #opr
LDA opr
IMM
DIR
EXT
A6 ii
B6 dd
C6 hh ll
D6 ee ff
E6 ff
2
3
4
4
3
2
4
5
LDA opr
LDA opr,X
LDA opr,X
LDA ,X
LDA opr,SP
LDA opr,SP
IX2
Load A from M
A ← (M)
0
–
–
ꢀ
ꢀ
–
IX1
IX
SP1
SP2
F6
9EE6 ff
9ED6 ee ff
Data Sheet
116
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Central Processor Unit (CPU) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Instruction Set Summary
Table 7-1. Instruction Set Summary (Sheet 5 of 7)
Effect
Source
Form
on CCR
Operation
Description
V H I N Z C
LDHX #opr
LDHX opr
IMM
DIR
45 ii jj
55 dd
3
4
Load H:X from M
H:X ← (M:M + 1)
0
–
–
–
ꢀ
ꢀ
ꢀ
–
LDX #opr
LDX opr
LDX opr
LDX opr,X
LDX opr,X
LDX ,X
LDX opr,SP
LDX opr,SP
IMM
DIR
EXT
IX2
IX1
IX
SP1
SP2
AE ii
BE dd
CE hh ll
DE ee ff
EE ff
FE
9EEE ff
9EDE ee ff
2
3
4
4
3
2
4
5
Load X from M
X ← (M)
0
–
ꢀ
–
LSL opr
LSLA
DIR
INH
INH
IX1
IX
38 dd
48
4
1
1
4
3
5
LSLX
Logical Shift Left
(Same as ASL)
58
C
0
ꢀ
ꢀ
–
–
–
–
ꢀ
ꢀ
ꢀ
ꢀ
LSL opr,X
LSL ,X
LSL opr,SP
68 ff
78
9E68 ff
b7
b7
b0
b0
SP1
LSR opr
LSRA
LSRX
LSR opr,X
LSR ,X
LSR opr,SP
DIR
INH
INH
IX1
IX
34 dd
44
4
1
1
4
3
5
54
0
C
Logical Shift Right
0
ꢀ
64 ff
74
SP1
9E64 ff
MOV opr,opr
MOV opr,X+
MOV #opr,opr
MOV X+,opr
DD
4E dd dd
5E dd
5
4
4
4
(M)Destination ← (M)Source
H:X ← (H:X) + 1 (IX+D, DIX+)
X:A ← (X) × (A)
DIX+
IMD
IX+D
Move
0
–
–
0
–
–
ꢀ
ꢀ
–
6E ii dd
7E dd
MUL
Unsigned multiply
–
–
0 INH
42
5
NEG opr
NEGA
DIR
INH
30 dd
40
4
1
1
4
3
5
M ← –(M) = $00 – (M)
A ← –(A) = $00 – (A)
X ← –(X) = $00 – (X)
M ← –(M) = $00 – (M)
M ← –(M) = $00 – (M)
NEGX
INH
50
Negate (Two’s Complement)
ꢀ
–
–
ꢀ
ꢀ
ꢀ
NEG opr,X
NEG ,X
NEG opr,SP
IX1
60 ff
70
9E60 ff
IX
SP1
NOP
NSA
No Operation
Nibble Swap A
None
–
–
–
–
–
–
–
–
–
–
– INH
– INH
9D
62
1
3
A ← (A[3:0]:A[7:4])
ORA #opr
ORA opr
IMM
DIR
EXT
AA ii
BA dd
CA hh ll
DA ee ff
EA ff
2
3
4
4
3
2
4
5
ORA opr
ORA opr,X
ORA opr,X
ORA ,X
ORA opr,SP
ORA opr,SP
IX2
Inclusive OR A and M
A ← (A) | (M)
0
–
–
ꢀ
ꢀ
–
IX1
IX
SP1
SP2
FA
9EEA ff
9EDA ee ff
PSHA
PSHH
PSHX
PULA
PULH
PULX
Push A onto Stack
Push H onto Stack
Push X onto Stack
Pull A from Stack
Pull H from Stack
Pull X from Stack
Push (A); SP ← (SP) – 1
Push (H); SP ← (SP) – 1
Push (X); SP ← (SP) – 1
SP ← (SP + 1); Pull (A)
SP ← (SP + 1); Pull (H)
SP ← (SP + 1); Pull (X)
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
– INH
– INH
– INH
– INH
– INH
– INH
87
8B
89
86
8A
88
2
2
2
2
2
2
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Central Processor Unit (CPU)
Data Sheet
117
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Table 7-1. Instruction Set Summary (Sheet 6 of 7)
Effect
Source
Form
on CCR
Operation
Description
V H I N Z C
ROL opr
DIR
INH
INH
IX1
IX
39 dd
49
4
1
1
4
3
5
ROLA
ROLX
59
C
Rotate Left through Carry
Rotate Right through Carry
ꢀ
–
–
–
–
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ROL opr,X
ROL ,X
69 ff
79
9E69 ff
b7
b0
ROL opr,SP
SP1
ROR opr
RORA
RORX
ROR opr,X
ROR ,X
ROR opr,SP
DIR
INH
INH
IX1
IX
36 dd
46
4
1
1
4
3
5
56
C
ꢀ
ꢀ
66 ff
76
b7
b0
SP1
9E66 ff
RSP
Reset Stack Pointer
Return from Interrupt
SP ← $FF
–
–
–
–
–
– INH
9C
1
SP ← (SP) + 1; Pull (CCR)
SP ← (SP) + 1; Pull (A)
SP ← (SP) + 1; Pull (X)
SP ← (SP) + 1; Pull (PCH)
SP ← (SP) + 1; Pull (PCL)
RTI
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ INH
80
7
SP ← SP + 1; Pull (PCH)
SP ← SP + 1; Pull (PCL)
RTS
Return from Subroutine
Subtract with Carry
–
–
–
–
–
–
–
– INH
81
4
SBC #opr
SBC opr
SBC opr
SBC opr,X
SBC opr,X
SBC ,X
SBC opr,SP
SBC opr,SP
IMM
DIR
EXT
A2 ii
B2 dd
C2 hh ll
D2 ee ff
E2 ff
2
3
4
4
3
2
4
5
IX2
A ← (A) – (M) – (C)
ꢀ
ꢀ
ꢀ
ꢀ
IX1
IX
F2
SP1
SP2
9EE2 ff
9ED2 ee ff
SEC
SEI
Set Carry Bit
C ← 1
I ← 1
–
–
–
–
–
1
–
–
–
–
1 INH
– INH
99
9B
1
2
Set Interrupt Mask
STA opr
DIR
EXT
IX2
B7 dd
C7 hh ll
D7 ee ff
E7 ff
3
4
4
3
2
4
5
STA opr
STA opr,X
STA opr,X
STA ,X
STA opr,SP
STA opr,SP
Store A in M
M ← (A)
0
–
–
ꢀ
ꢀ
– IX1
IX
F7
SP1
SP2
9EE7 ff
9ED7 ee ff
STHX opr
Store H:X in M
(M:M + 1) ← (H:X)
0
–
–
–
–
0
ꢀ
ꢀ
– DIR
– INH
35 dd
8E
4
1
Enable Interrupts, Stop Processing,
Refer to MCU Documentation
STOP
I ← 0; Stop Processing
–
–
STX opr
DIR
EXT
IX2
BF dd
CF hh ll
DF ee ff
EF ff
3
4
4
3
2
4
5
STX opr
STX opr,X
STX opr,X
STX ,X
STX opr,SP
STX opr,SP
Store X in M
M ← (X)
0
–
–
–
–
ꢀ
ꢀ
ꢀ
ꢀ
– IX1
IX
FF
SP1
SP2
9EEF ff
9EDF ee ff
SUB #opr
SUB opr
SUB opr
SUB opr,X
SUB opr,X
SUB ,X
SUB opr,SP
SUB opr,SP
IMM
DIR
EXT
A0 ii
B0 dd
C0 hh ll
D0 ee ff
E0 ff
2
3
4
4
3
2
4
5
IX2
Subtract
A ← (A) – (M)
ꢀ
ꢀ
IX1
IX
F0
SP1
SP2
9EE0 ff
9ED0 ee ff
Data Sheet
118
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Central Processor Unit (CPU) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Opcode Map
Table 7-1. Instruction Set Summary (Sheet 7 of 7)
Effect
Source
Form
on CCR
Operation
Description
V H I N Z C
PC ← (PC) + 1; Push (PCL)
SP ← (SP) – 1; Push (PCH)
SP ← (SP) – 1; Push (X)
SP ← (SP) – 1; Push (A)
SWI
Software Interrupt
–
–
1
–
–
– INH
83
9
SP ← (SP) – 1; Push (CCR)
SP ← (SP) – 1; I ← 1
PCH ← Interrupt Vector High Byte
PCL ← Interrupt Vector Low Byte
TAP
TAX
TPA
Transfer A to CCR
Transfer A to X
CCR ← (A)
X ← (A)
ꢀ
–
–
ꢀ
–
–
ꢀ
–
–
ꢀ
–
–
ꢀ
–
–
ꢀ INH
– INH
– INH
84
97
85
2
1
1
Transfer CCR to A
A ← (CCR)
TST opr
TSTA
DIR
INH
3D dd
4D
3
1
1
3
2
4
TSTX
INH
5D
Test for Negative or Zero
(A) – $00 or (X) – $00 or (M) – $00
0
–
–
ꢀ
ꢀ
–
TST opr,X
TST ,X
TST opr,SP
IX1
6D ff
7D
9E6D ff
IX
SP1
TSX
TXA
TXS
Transfer SP to H:X
Transfer X to A
H:X ← (SP) + 1
A ← (X)
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
– INH
– INH
– INH
95
9F
94
2
1
2
Transfer H:X to SP
(SP) ← (H:X) – 1
I bit ← 0; Inhibit CPU clocking
WAIT
Enable Interrupts; Wait for Interrupt
–
–
0
–
–
– INH
8F
1
until interrupted
A
C
CCR
dd
dd rr
DD
DIR
DIX+
ee ff
EXT
ff
Accumulator
Carry/borrow bit
Condition code register
Direct address of operand
Direct address of operand and relative offset of branch instruction
Direct to direct addressing mode
n
Any bit
Operand (one or two bytes)
Program counter
opr
PC
PCH
PCL
REL
rel
rr
SP1
SP2
SP
U
Program counter high byte
Program counter low byte
Relative addressing mode
Relative program counter offset byte
Relative program counter offset byte
Stack pointer, 8-bit offset addressing mode
Stack pointer 16-bit offset addressing mode
Stack pointer
Direct addressing mode
Direct to indexed with post increment addressing mode
High and low bytes of offset in indexed, 16-bit offset addressing
Extended addressing mode
Offset byte in indexed, 8-bit offset addressing
Half-carry bit
H
Undefined
H
Index register high byte
V
Overflow bit
hh ll
I
High and low bytes of operand address in extended addressing
Interrupt mask
X
Z
Index register low byte
Zero bit
ii
Immediate operand byte
&
Logical AND
IMD
Immediate source to direct destination addressing mode
|
Logical OR
IMM
INH
IX
Immediate addressing mode
Inherent addressing mode
Indexed, no offset addressing mode
Indexed, no offset, post increment addressing mode
⊕
( )
–( )
#
Logical EXCLUSIVE OR
Contents of
Negation (two’s complement)
Immediate value
IX+
IX+D
IX1
IX1+
IX2
M
Indexed with post increment to direct addressing mode
Indexed, 8-bit offset addressing mode
Indexed, 8-bit offset, post increment addressing mode
Indexed, 16-bit offset addressing mode
Memory location
«
←
?
:
ꢀ
Sign extend
Loaded with
If
Concatenated with
Set or cleared
Not affected
N
Negative bit
—
7.8 Opcode Map
See Table 7-2.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
119
MOTOROLA
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Data Sheet
120
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Central Processor Unit (CPU)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 8. External Interrupt (IRQ)
8.1 Introduction
8.2 Features
The IRQ (external interrupt) module provides a maskable interrupt input.
Features of the IRQ module include:
•
•
•
•
•
•
A dedicated external interrupt pin (IRQ)
IRQ interrupt control bits
Hysteresis buffer
Programmable edge-only or edge and level interrupt sensitivity
Automatic interrupt acknowledge
Internal pullup resistor
8.3 Functional Description
A low applied to the external interrupt pin can latch a central processor unit (CPU)
interrupt request. Figure 8-1 shows the structure of the IRQ module.
Interrupt signals on the IRQ pin are latched into the IRQ latch. An interrupt latch
remains set until one of the following actions occurs:
•
Vector fetch — A vector fetch automatically generates an interrupt
acknowledge signal that clears the latch that caused the vector fetch.
•
Software clear — Software can clear an interrupt latch by writing to the
appropriate acknowledge bit in the interrupt status and control register
(INTSCR). Writing a 1 to the ACK bit clears the IRQ latch.
•
Reset — A reset automatically clears the interrupt latch.
The external interrupt pin is falling-edge triggered out of reset and is
software-configurable to be either falling-edge or falling-edge and low-level
triggered. The MODE bit in the INTSCR controls the triggering sensitivity of the IRQ
pin.
When an interrupt pin is edge-triggered only (MODE = 0), the interrupt remains set
until a vector fetch, software clear, or reset occurs.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
121
MOTOROLA
External Interrupt (IRQ)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
External Interrupt (IRQ)
RESET
ACK
TO CPU FOR
BIL/BIH
INSTRUCTIONS
VECTOR
FETCH
DECODER
VDD
INTERNAL
PULLUP
DEVICE
VDD
IRQF
CLR
D
Q
IRQ
INTERRUPT
REQUEST
SYNCHRONIZER
CK
IRQ
IMASK
MODE
TO MODE
SELECT
LOGIC
HIGH
VOLTAGE
DETECT
Figure 8-1. IRQ Module Block Diagram
When an interrupt pin is both falling-edge and low-level triggered (MODE = 1), the
interrupt remains set until both of these events occur:
•
•
Vector fetch or software clear
Return of the interrupt pin to a high level
The vector fetch or software clear may occur before or after the interrupt pin returns
to a high level. As long as the pin is low, the interrupt request remains pending. A
reset will clear the latch and the MODE control bit, thereby clearing the interrupt
even if the pin stays low.
When set, the IMASK bit in the INTSCR masks all external interrupt requests. A
latched interrupt request is not presented to the interrupt priority logic unless the
IMASK bit is clear.
NOTE:
The interrupt mask (I) in the condition code register (CCR) masks all interrupt
requests, including external interrupt requests.
Addr.
Register Name
Bit 7
6
5
4
3
2
0
1
IMASK
0
Bit 0
MODE
0
Read:
0
0
0
0
IRQF
IRQ Status and Control
Register (INTSCR) Write:
$001D
ACK
0
See page 124.
Reset:
0
0
0
0
0
= Unimplemented
Figure 8-2. IRQ I/O Register Summary
Data Sheet
122
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
External Interrupt (IRQ)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
External Interrupt (IRQ)
IRQ Pin
8.4 IRQ Pin
A falling edge on the IRQ pin can latch an interrupt request into the IRQ latch. A
vector fetch, software clear, or reset clears the IRQ latch.
If the MODE bit is set, the IRQ pin is both falling-edge-sensitive and
low-level-sensitive. With MODE set, both of the following actions must occur to
clear IRQ:
•
Vector fetch or software clear — A vector fetch generates an interrupt
acknowledge signal to clear the latch. Software may generate the interrupt
acknowledge signal by writing a 1 to the ACK bit in the interrupt status and
control register (INTSCR). The ACK bit is useful in applications that poll the
IRQ pin and require software to clear the IRQ latch. Writing to the ACK bit
prior to leaving an interrupt service routine can also prevent spurious
interrupts due to noise. Setting ACK does not affect subsequent transitions
on the IRQ pin. A falling edge that occurs after writing to the ACK bit latches
another interrupt request. If the IRQ mask bit, IMASK, is clear, the CPU
loads the program counter with the vector address at locations $FFFA and
$FFFB.
•
Return of the IRQ pin to a high level — As long as the IRQ pin is low, IRQ
remains active.
The vector fetch or software clear and the return of the IRQ pin to a high level may
occur in any order. The interrupt request remains pending as long as the IRQ pin
is low. A reset will clear the latch and the MODE control bit, thereby clearing the
interrupt even if the pin stays low.
If the MODE bit is clear, the IRQ pin is falling-edge-sensitive only. With MODE
clear, a vector fetch or software clear immediately clears the IRQ latch.
The IRQF bit in the INTSCR register can be used to check for pending interrupts.
The IRQF bit is not affected by the IMASK bit, which makes it useful in applications
where polling is preferred.
Use the BIH or BIL instruction to read the logic level on the IRQ pin.
NOTE:
When using the level-sensitive interrupt trigger, avoid false interrupts by masking
interrupt requests in the interrupt routine.
8.5 IRQ Module During Break Interrupts
The BCFE bit in the SIM break flag control register (SBFCR) enables software to
clear the latch during the break state. See Section 20. Development Support.
To allow software to clear the IRQ latch during a break interrupt, write a 1 to the
BCFE bit. If a latch is cleared during the break state, it remains cleared when the
MCU exits the break state.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
123
MOTOROLA
External Interrupt (IRQ)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
External Interrupt (IRQ)
To protect CPU interrupt flags during the break state, write a 0 to the BCFE bit. With
BCFE at 0 (its default state), writing to the ACK bit in the IRQ status and control
register during the break state has no effect on the IRQ interrupt flags.
8.6 IRQ Status and Control Register
The IRQ status and control register (INTSCR) controls and monitors operation of
the IRQ module. The INTSCR:
•
•
•
•
Shows the state of the IRQ flag
Clears the IRQ latch
Masks IRQ interrupt request
Controls triggering sensitivity of the IRQ interrupt pin
Address:
$001D
Bit 7
0
6
0
5
0
4
0
3
2
0
1
IMASK
0
Bit 0
MODE
0
Read:
Write:
Reset:
IRQF
ACK
0
0
0
0
0
0
= Unimplemented
Figure 8-3. IRQ Status and Control Register (INTSCR)
IRQF — IRQ Flag Bit
This read-only status bit is high when the IRQ interrupt is pending.
1 = IRQ interrupt pending
0 = IRQ interrupt not pending
ACK — IRQ Interrupt Request Acknowledge Bit
Writing a 1 to this write-only bit clears the IRQ latch. ACK always reads as 0.
Reset clears ACK.
IMASK — IRQ Interrupt Mask Bit
Writing a 1 to this read/write bit disables IRQ interrupt requests. Reset clears
IMASK.
1 = IRQ interrupt requests disabled
0 = IRQ interrupt requests enabled
MODE — IRQ Edge/Level Select Bit
This read/write bit controls the triggering sensitivity of the IRQ pin. Reset clears
MODE.
1 = IRQ interrupt requests on falling edges and low levels
0 = IRQ interrupt requests on falling edges only
Data Sheet
124
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
External Interrupt (IRQ)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 9. Keyboard Interrupt Module (KBI)
9.1 Introduction
9.2 Features
The keyboard interrupt module (KBI) provides eight independently maskable
external interrupts which are accessible via PTA0–PTA7. When a port pin is
enabled for keyboard interrupt function, an internal pullup/pulldown device is also
enabled on the pin.
Features include:
•
Eight keyboard interrupt pins with separate keyboard interrupt enable bits
and one keyboard interrupt mask
•
•
•
•
•
•
Hysteresis buffers
Programmable edge-only or edge- and level- interrupt sensitivity
Edge detect programmable for rising or falling edges
Level detect programmable for high or low levels
Exit from low-power modes
Pullup/pulldown device automatically configured based on polarity of
edge/level selection
9.3 Functional Description
Writing to the KBIE7–KBIE0 bits in the keyboard interrupt enable register
independently enables or disables each port A pin as a keyboard interrupt pin.
Enabling a keyboard interrupt pin also enables its internal pullup/pulldown device.
On falling edge or low level selection a pullup device is configured. On rising edge
or high level selection a pulldown device is configured.
•
A falling edge is detected when an enabled keyboard input signal is seen as
a 1 (the deasserted level) during one bus cycle and then a 0 (the asserted
level) during the next cycle.
•
A rising edge is detected when the input signal is seen as a 0 during one bus
cycle and then a 1 during the next cycle.
A keyboard interrupt is latched when one or more keyboard pins are asserted. The
MODEK bit in the keyboard status and control register controls the triggering mode
of the keyboard interrupt.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
125
MOTOROLA
Keyboard Interrupt Module (KBI)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
P O R T B
D D R B
P O R T F
D D R F
G T P O R
D D R G
A
P O R T
D D R A
P O R T C
D D R C
P O R T E
D D R E
P O R T D
D D R D
Data Sheet
126
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Keyboard Interrupt Module (KBI) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
Functional Description
The KBIP7–KBIP0 bits determine the polarity of the keyboard pin detection. These
bits along with the MODEK bit determine whether a logic level (0 or 1) and/or a
falling (or rising) edge is being detected.
•
If the keyboard interrupt is edge-sensitive only, a falling (or rising) edge on
a keyboard pin does not latch an interrupt request if another keyboard pin is
already asserted. To prevent losing an interrupt request on one pin because
another pin is still asserted, software can disable the latter pin while it is
asserted.
•
If the keyboard interrupt is edge and level sensitive, an interrupt request is
present as long as any keyboard interrupt pin is asserted and the pin is
keyboard interrupt enabled.
INTERNAL BUS
VECTOR FETCH
DECODER
ACKK
RESET
1
0
KBD0
VDD
S
KBIE0
KEYF
CLR
TO PULLUP/
PULLDOWN ENABLE
D
Q
SYNCHRONIZER
KBIP0
CK
1
0
IMASKK
KBD7
KEYBOARD
INTERRUPT
REQUEST
S
KBIE7
MODEK
TO PULLUP/
PULLDOWN ENABLE
KBIP7
Figure 9-2. Keyboard Module Block Diagram
Addr.
Register Name
Keyboard Status and Control
Register (INTKBSCR) Write:
Bit 7
6
5
4
3
2
1
Bit 0
MODEK
0
Read:
0
0
0
0
KEYF
0
ACKK
0
IMASKK
$001A
$001B
$0448
See page 130.
Reset:
0
KBIE7
0
0
KBIE6
0
0
KBIE5
0
0
KBIE4
0
0
KBIE3
0
0
KBIE1
0
Read:
Keyboard Interrupt Enable
Register (INTKBIER) Write:
KBIE2
KBIE0
0
See page 131.
Reset:
0
KBIP2
0
Read:
Keyboard Interrupt Polarity
Register (INTKBIPR) Write:
KBIP7
0
KBIP6
0
KBIP5
0
KBIP4
0
KBIP3
0
KBIP1
0
KBIP0
0
See page 132.
Reset:
= Unimplemented
Figure 9-3. I/O Register Summary
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Keyboard Interrupt Module (KBI)
Data Sheet
127
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
If the MODEK bit is set and depending on the KBIPx bit, the keyboard interrupt pins
are both falling (or rising) edge and low (or high) level sensitive, and both of the
following actions must occur to clear a keyboard interrupt request:
•
Vector fetch or software clear — A vector fetch generates an interrupt
acknowledge signal to clear the interrupt request. Software may generate
the interrupt acknowledge signal by writing a 1 to the ACKK bit in the
keyboard status and control register (INTKBSCR). The ACKK bit is useful in
applications that poll the keyboard interrupt pins and require software to
clear the keyboard interrupt request. Writing to the ACKK bit prior to leaving
an interrupt service routine can also prevent spurious interrupts due to
noise. Setting ACKK does not affect subsequent transitions on the keyboard
interrupt pins. A falling (or rising) edge that occurs after writing to the ACKK
bit latches another interrupt request. If the keyboard interrupt mask bit,
IMASKK, is clear, the CPU loads the program counter with the vector
address at locations $FFE0 and $FFE1.
•
Return of all enabled keyboard interrupt pins to 1 (or 0) — As long as any
enabled keyboard interrupt pin is 0 (or 1), the keyboard interrupt remains
set.
The vector fetch or software clear and the return of all enabled keyboard interrupt
pins to 1 (or 0) may occur in any order.
If the MODEK bit is clear and depending on the KBIPx bit, the keyboard interrupt
pin is falling (or rising) edge sensitive only. With MODEK clear, a vector fetch or
software clear immediately clears the keyboard interrupt request.
Reset clears the keyboard interrupt request and the MODEK bit, clearing the
interrupt request even if a keyboard interrupt pin stays at 0 (or 1).
The keyboard flag bit (KEYF) in the keyboard status and control register can be
used to see if a pending interrupt exists. The KEYF bit is not affected by the
keyboard interrupt mask bit (IMASKK) which makes it useful in applications where
polling is preferred.
To determine the logic level on a keyboard interrupt pin, use the data direction
register to configure the pin as an input and read the data register.
NOTE:
Setting a keyboard interrupt enable bit (KBIEx) forces the corresponding keyboard
interrupt pin to be an input, overriding the data direction register. However, the data
direction register bit must be a 0 for software to read the pin.
Data Sheet
128
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Keyboard Interrupt Module (KBI)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
Keyboard Initialization
9.4 Keyboard Initialization
When a keyboard interrupt pin is enabled, it takes time for the internal
pullup/pulldown device to reach a 1 (or 0). Therefore, a false interrupt can occur as
soon as the pin is enabled.
To prevent a false interrupt on keyboard initialization:
1. Mask keyboard interrupts by setting the IMASKK bit in the keyboard status
and control register.
2. Enable the KBI pins and polarity by setting the appropriate KBIEx bits in the
keyboard interrupt enable register and the KBIPx bits in the keyboard
interrupt polarity register.
3. Write to the ACKK bit in the keyboard status and control register to clear any
false interrupts.
4. Clear the IMASKK bit.
An interrupt signal on an edge-triggered pin can be acknowledged immediately
after enabling the pin. An interrupt signal on an edge- and level-triggered interrupt
pin must be acknowledged after a delay that depends on the external load.
Another way to avoid a false interrupt:
1. Configure the keyboard pins as outputs by setting the appropriate DDRA
bits in data direction register A.
2. Write 1s (or 0s) to the appropriate port A data register bits.
3. Enable the KBI pins and polarity by setting the appropriate KBIEx bits in the
keyboard interrupt enable register and the KBIPx bits in the keyboard
interrupt polarity register.
9.5 Low-Power Modes
The WAIT and STOP instructions put the microcontroller unit (MCU) in low
power-consumption standby modes.
9.5.1 Wait Mode
9.5.2 Stop Mode
The keyboard module remains active in wait mode. Clearing the IMASKK bit in the
keyboard status and control register enables keyboard interrupt requests to bring
the MCU out of wait mode.
The keyboard module remains active in stop mode. Clearing the IMASKK bit in the
keyboard status and control register enables keyboard interrupt requests to bring
the MCU out of stop mode.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
129
MOTOROLA
Keyboard Interrupt Module (KBI)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
9.6 Keyboard Module During Break Interrupts
The system integration module (SIM) controls whether the keyboard interrupt latch
can be cleared during the break state. The BCFE bit in the break flag control
register (BFCR) enables software to clear status bits during the break state.
To allow software to clear the keyboard interrupt latch during a break interrupt,
write a 1 to the BCFE bit. If a latch is cleared during the break state, it remains
cleared when the MCU exits the break state.
To protect the latch during the break state, write a 0 to the BCFE bit. With BCFE
at 0 (its default state), writing to the keyboard acknowledge bit (ACKK) in the
keyboard status and control register during the break state has no effect. See 9.7.1
Keyboard Status and Control Register.
9.7 I/O Registers
These registers control and monitor operation of the keyboard module:
•
•
•
Keyboard status and control register (INTKBSCR)
Keyboard interrupt enable register (INTKBIER)
Keyboard interrupt polarity register (INTKBIPR)
9.7.1 Keyboard Status and Control Register
The keyboard status and control register:
•
•
•
•
Flags keyboard interrupt requests
Acknowledges keyboard interrupt requests
Masks keyboard interrupt requests
Controls keyboard interrupt triggering sensitivity
Address: $001A
Bit 7
6
0
5
0
4
0
3
2
1
IMASKK
0
Bit 0
MODEK
0
Read:
Write:
Reset:
0
KEYF
0
ACKK
0
0
0
0
0
0
= Unimplemented
Figure 9-4. Keyboard Status and Control Register (INTKBSCR)
Bits 7–4 — Not used
These read-only bits always read as 0s.
KEYF — Keyboard Flag Bit
This read-only bit is set when a keyboard interrupt is pending. Reset clears the
KEYF bit.
1 = Keyboard interrupt pending
0 = No keyboard interrupt pending
Data Sheet
130
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Keyboard Interrupt Module (KBI)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
I/O Registers
ACKK — Keyboard Acknowledge Bit
Writing a 1 to this write-only bit clears the keyboard interrupt request. ACKK
always reads as 0. Reset clears ACKK.
IMASKK — Keyboard Interrupt Mask Bit
Writing a 1 to this read/write bit prevents the output of the keyboard interrupt
mask from generating interrupt requests. Reset clears the IMASKK bit.
1 = Keyboard interrupt requests masked
0 = Keyboard interrupt requests not masked
MODEK — Keyboard Triggering Sensitivity Bit
This read/write bit controls the triggering sensitivity of the keyboard interrupt
pins. Reset clears MODEK.
1 = Keyboard interrupt requests on edge and level detect
0 = Keyboard interrupt requests on edges only
9.7.2 Keyboard Interrupt Enable Register
The keyboard interrupt enable register enables or disables each port A pin to
operate as a keyboard interrupt pin.
Address: $001B
Bit 7
KBIE7
0
6
KBIE6
0
5
KBIE5
0
4
KBIE4
0
3
KBIE3
0
2
KBIE2
0
1
KBIE1
0
Bit 0
KBIE0
0
Read:
Write:
Reset:
Figure 9-5. Keyboard Interrupt Enable Register (INTKBIER)
KBIE7–KBIE0 — Keyboard Interrupt Enable Bits
Each of these read/write bits enables the corresponding keyboard interrupt pin
to latch interrupt requests. Reset clears the keyboard interrupt enable register.
1 = PTAx pin enabled as keyboard interrupt pin
0 = PTAx pin not enabled as keyboard interrupt pin
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
131
MOTOROLA
Keyboard Interrupt Module (KBI)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
9.7.3 Keyboard Interrupt Polarity Register
The KBIP7–KBIP0 bits determine the polarity of the keyboard pin detection. These
bits along with the MODEK bit determine whether a logic level (0 or 1) and/or a
falling (or rising) edge is being detected. The KBIPx bits also select the pullup
resistor (KBIPx = 0) or pulldown resistor (KBIPx = 1) for each enabled keyboard
interrupt pin.
Address: $0448
Bit 7
KBIP7
0
6
KBIP6
0
5
KBIP5
0
4
KBIP4
0
3
KBIP3
0
2
KBIP2
0
1
KBIP1
0
Bit 0
KBIP0
0
Read:
Write:
Reset:
Figure 9-6. Keyboard Interrupt Polarity Register (INTKBIPR)
KBIP7–KBIP0 — Keyboard Interrupt Polarity Bits
Each of these read/write bits enables the polarity of the keyboard interrupt pin.
Reset clears the keyboard interrupt polarity register.
1 = Keyboard polarity is rising edge and/or high level
0 = Keyboard polarity is falling edge and/or low level
Data Sheet
132
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Keyboard Interrupt Module (KBI)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 10. Low-Power Modes
10.1 Introduction
10.1.1 Wait Mode
The microcontroller (MCU) may enter two low-power modes: wait mode and stop
mode. They are common to all HC08 MCUs and are entered through instruction
execution. This section describes how each module acts in the low-power modes.
The WAIT instruction puts the MCU in a low-power standby mode in which the
central processor unit (CPU) clock is disabled but the bus clock continues to run.
Power consumption can be further reduced by disabling the low-voltage inhibit
(LVI) module through bits in the CONFIG1 register. See Section 5. Configuration
Register (CONFIG).
10.1.2 Stop Mode
Stop mode is entered when a STOP instruction is executed. The CPU clock is
disabled and the bus clock is disabled if the OSCENINSTOP bit in the CONFIG2
register is a 0. See Section 5. Configuration Register (CONFIG).
10.2 Analog-to-Digital Converter (ADC)
10.2.1 Wait Mode
The analog-to-digital converter (ADC) continues normal operation during wait
mode. Any enabled CPU interrupt request from the ADC can bring the MCU out of
wait mode. If the ADC is not required to bring the MCU out of wait mode, power
down the ADC by setting ADCH4–ADCH0 bits in the ADC status and control
register before executing the WAIT instruction.
10.2.2 Stop Mode
The ADC module is inactive after the execution of a STOP instruction. Any pending
conversion is aborted. ADC conversions resume when the MCU exits stop mode
after an external interrupt. Allow one conversion cycle to stabilize the analog
circuitry.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
133
MOTOROLA
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Low-Power Modes
10.3 Break Module (BRK)
10.3.1 Wait Mode
The break (BRK) module is active in wait mode. In the break routine, the user can
subtract one from the return address on the stack if the SBSW bit in the break
status register is set.
10.3.2 Stop Mode
The break module is inactive in stop mode. The STOP instruction does not affect
break module register states.
10.4 Central Processor Unit (CPU)
10.4.1 Wait Mode
The WAIT instruction:
•
Clears the interrupt mask (I bit) in the condition code register, enabling
interrupts. After exit from wait mode by interrupt, the I bit remains clear. After
exit by reset, the I bit is set.
•
Disables the CPU clock
10.4.2 Stop Mode
The STOP instruction:
•
Clears the interrupt mask (I bit) in the condition code register, enabling
external interrupts. After exit from stop mode by external interrupt, the I bit
remains clear. After exit by reset, the I bit is set.
•
Disables the CPU clock
After exiting stop mode, the CPU clock begins running after the oscillator
stabilization delay.
10.5 Clock Generator Module (CGM)
10.5.1 Wait Mode
The clock generator module (CGM) remains active in wait mode. Before entering
wait mode, software can disengage and turn off the PLL by clearing the BCS and
PLLON bits in the PLL control register (PCTL). Less power-sensitive applications
can disengage the PLL without turning it off. Applications that require the PLL to
wake the MCU from wait mode also can deselect the PLL output without turning off
the PLL.
Data Sheet
134
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Low-Power Modes
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Low-Power Modes
Computer Operating Properly Module (COP)
10.5.2 Stop Mode
If the OSCENINSTOP bit in the CONFIG2 register is cleared (default), then the
STOP instruction disables the CGM (oscillator and phase-locked loop) and holds
low all CGM outputs (CGMXCLK, CGMOUT, and CGMINT).
If the STOP instruction is executed with the VCO clock, CGMVCLK, divided by two
driving CGMOUT, the PLL automatically clears the BCS bit in the PLL control
register (PCTL), thereby selecting the crystal clock, CGMXCLK, divided by two as
the source of CGMOUT. When the MCU recovers from STOP, the crystal clock
divided by two drives CGMOUT and BCS remains clear.
If the OSCENINSTOP bit in the CONFIG2 register is set, then the phase locked
loop is shut off, but the oscillator will continue to operate in stop mode.
10.6 Computer Operating Properly Module (COP)
10.6.1 Wait Mode
The COP remains active during wait mode. If COP is enabled, a reset will occur at
COP timeout.
10.6.2 Stop Mode
Stop mode turns off the COPCLK input to the COP and clears the SIM counter.
Service the COP immediately before entering or after exiting stop mode to ensure
a full COP timeout period after entering or exiting stop mode.
The STOP bit in the CONFIG1 register enables the STOP instruction. To prevent
inadvertently turning off the COP with a STOP instruction, disable the STOP
instruction by clearing the STOP bit.
10.7 External Interrupt Module (IRQ)
10.7.1 Wait Mode
The external interrupt (IRQ) module remains active in wait mode. Clearing the
IMASK bit in the IRQ status and control register enables IRQ CPU interrupt
requests to bring the MCU out of wait mode.
10.7.2 Stop Mode
The IRQ module remains active in stop mode. Clearing the IMASK bit in the IRQ
status and control register enables IRQ CPU interrupt requests to bring the MCU
out of stop mode.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
135
MOTOROLA
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Low-Power Modes
10.8 Keyboard Interrupt Module (KBI)
10.8.1 Wait Mode
The keyboard interrupt (KBI) module remains active in wait mode. Clearing the
IMASKK bit in the keyboard status and control register enables keyboard interrupt
requests to bring the MCU out of wait mode.
10.8.2 Stop Mode
The keyboard module remains active in stop mode. Clearing the IMASKK bit in the
keyboard status and control register enables keyboard interrupt requests to bring
the MCU out of stop mode.
10.9 Low-Voltage Inhibit Module (LVI)
10.9.1 Wait Mode
If enabled, the low-voltage inhibit (LVI) module remains active in wait mode. If
enabled to generate resets, the LVI module can generate a reset and bring the
MCU out of wait mode.
10.9.2 Stop Mode
If enabled, the LVI module remains active in stop mode. If enabled to generate
resets, the LVI module can generate a reset and bring the MCU out of stop mode.
10.10 Enhanced Serial Communications Interface Module (ESCI)
10.10.1 Wait Mode
The enhanced serial communications interface (ESCI), or SCI module for short,
module remains active in wait mode. Any enabled CPU interrupt request from the
SCI module can bring the MCU out of wait mode.
If SCI module functions are not required during wait mode, reduce power
consumption by disabling the module before executing the WAIT instruction.
10.10.2 Stop Mode
The SCI module is inactive in stop mode. The STOP instruction does not affect SCI
register states. SCI module operation resumes after the MCU exits stop mode.
Because the internal clock is inactive during stop mode, entering stop mode during
an SCI transmission or reception results in invalid data.
Data Sheet
136
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Low-Power Modes
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Low-Power Modes
Serial Peripheral Interface Module (SPI)
10.11 Serial Peripheral Interface Module (SPI)
10.11.1 Wait Mode
The serial peripheral interface (SPI) module remains active in wait mode. Any
enabled CPU interrupt request from the SPI module can bring the MCU out of wait
mode.
If SPI module functions are not required during wait mode, reduce power
consumption by disabling the SPI module before executing the WAIT instruction.
10.11.2 Stop Mode
The SPI module is inactive in stop mode. The STOP instruction does not affect SPI
register states. SPI operation resumes after an external interrupt. If stop mode is
exited by reset, any transfer in progress is aborted, and the SPI is reset.
10.12 Timer Interface Module (TIM1 and TIM2)
10.12.1 Wait Mode
The timer interface modules (TIM) remain active in wait mode. Any enabled CPU
interrupt request from the TIM can bring the MCU out of wait mode.
If TIM functions are not required during wait mode, reduce power consumption by
stopping the TIM before executing the WAIT instruction.
10.12.2 Stop Mode
The TIM is inactive in stop mode. The STOP instruction does not affect register
states or the state of the TIM counter. TIM operation resumes when the MCU exits
stop mode after an external interrupt.
10.13 Timebase Module (TBM)
10.13.1 Wait Mode
The timebase module (TBM) remains active after execution of the WAIT
instruction. In wait mode, the timebase register is not accessible by the CPU.
If the timebase functions are not required during wait mode, reduce the power
consumption by stopping the timebase before enabling the WAIT instruction.
10.13.2 Stop Mode
The timebase module may remain active after execution of the STOP instruction if
the oscillator has been enabled to operate during stop mode through the
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
137
MOTOROLA
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Low-Power Modes
OSCENINSTOP bit in the CONFIG2 register. The timebase module can be used
in this mode to generate a periodic wakeup from stop mode.
If the oscillator has not been enabled to operate in stop mode, the timebase module
will not be active during stop mode. In stop mode, the timebase register is not
accessible by the CPU.
If the timebase functions are not required during stop mode, reduce the power
consumption by stopping the timebase before enabling the STOP instruction.
10.14 Motorola Scalable Controller Area Network Module (MSCAN)
10.14.1 Wait Mode
The Motorola scalable controller area network (MSCAN) module remains active
after execution of the WAIT instruction. In wait mode, the MSCAN08 registers are
not accessible by the CPU.
If the MSCAN08 functions are not required during wait mode, reduce the power
consumption by disabling the MSCAN08 module before enabling the WAIT
instruction.
10.14.2 Stop Mode
The MSCAN08 module is inactive in stop mode. The STOP instruction does not
affect MSCAN08 register states.
Because the internal clock is inactive during stop mode, entering stop mode during
an MSCAN08 transmission or reception results in invalid data.
10.15 Exiting Wait Mode
These events restart the CPU clock and load the program counter with the reset
vector or with an interrupt vector:
•
External reset — A low on the RST pin resets the MCU and loads the
program counter with the contents of locations $FFFE and $FFFF.
•
External interrupt — A high-to-low transition on an external interrupt pin
(IRQ pin) loads the program counter with the contents of locations: $FFFA
and $FFFB; IRQ pin.
•
•
Break interrupt — In emulation mode, a break interrupt loads the program
counter with the contents of $FFFC and $FFFD.
Computer operating properly (COP) module reset — A timeout of the COP
counter resets the MCU and loads the program counter with the contents of
$FFFE and $FFFF.
•
Low-voltage inhibit (LVI) module reset — A power supply voltage below the
VTRIPF voltage resets the MCU and loads the program counter with the
contents of locations $FFFE and $FFFF.
Data Sheet
138
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Low-Power Modes
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Low-Power Modes
Exiting Wait Mode
•
•
•
Clock generator module (CGM) interrupt — A CPU interrupt request from
the CGM loads the program counter with the contents of $FFF8 and $FFF9.
Keyboard interrupt (KBI) module — A CPU interrupt request from the KBI
module loads the program counter with the contents of $FFE0 and $FFE1.
Timer 1 interface (TIM1) module interrupt — A CPU interrupt request from
the TIM1 loads the program counter with the contents of:
–
–
–
$FFF2 and $FFF3; TIM1 overflow
$FFF4 and $FFF5; TIM1 channel 1
$FFF6 and $FFF7; TIM1 channel 0
•
Timer 2 interface module (TIM2) interrupt — A CPU interrupt request from
the TIM2 loads the program counter with the contents of:
–
–
–
–
–
–
–
$FFEC and $FFED; TIM2 overflow
$FFEE and $FFEF; TIM2 channel 1
$FFF0 and $FFF1; TIM2 channel 0
$FFCC and $FFCD; TIM2 channel 5
$FFCE and $FFCF; TIM2 channel 4
$FFD0 and $FFD1; TIM2 channel 3
$FFD2 and $FFD3; TIM2 channel 2
•
•
Serial peripheral interface (SPI) module interrupt — A CPU interrupt request
from the SPI loads the program counter with the contents of:
–
–
$FFE8 and $FFE9; SPI transmitter
$FFEA and $FFEB; SPI receiver
Serial communications interface (SCI) module interrupt — A CPU interrupt
request from the SCI loads the program counter with the contents of:
–
–
–
$FFE2 and $FFE3; SCI transmitter
$FFE4 and $FFE5; SCI receiver
$FFE6 and $FFE7; SCI receiver error
•
•
•
Analog-to-digital converter (ADC) module interrupt — A CPU interrupt
request from the ADC loads the program counter with the contents of:
$FFDE and $FFDF; ADC conversion complete.
Timebase module (TBM) interrupt — A CPU interrupt request from the TBM
loads the program counter with the contents of: $FFDC and $FFDD; TBM
interrupt.
Motorola scalable controller area network (MSCAN) module interrupt — A
CPU interrupt request from the MSCAN08 loads the program counter with
the contents of:
–
–
–
–
$FFD4 and $FFD5; MSCAN08 transmitter
$FFD6 and $FFD7; MSCAN08 receiver
$FFD8 and $FFD9; MSCAN08 error
$FFDA and $FFDB; MSCAN08 wakeup
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
139
MOTOROLA
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Low-Power Modes
10.16 Exiting Stop Mode
These events restart the system clocks and load the program counter with the reset
vector or with an interrupt vector:
•
External reset — A low on the RST pin resets the MCU and loads the
program counter with the contents of locations $FFFE and $FFFF.
•
External interrupt — A high-to-low transition on an external interrupt pin
loads the program counter with the contents of locations:
–
–
$FFFA and $FFFB; IRQ pin
$FFE0 and $FFE1; keyboard interrupt pins (low-to-high transition when
KBIPx bits are set)
•
Low-voltage inhibit (LVI) reset — A power supply voltage below the VTRIPF
voltage resets the MCU and loads the program counter with the contents of
locations $FFFE and $FFFF.
•
•
Break interrupt — In emulation mode, a break interrupt loads the program
counter with the contents of locations $FFFC and $FFFD.
Timebase module (TBM) interrupt — A TBM interrupt loads the program
counter with the contents of locations $FFDC and $FFDD when the
timebase counter has rolled over. This allows the TBM to generate a
periodic wakeup from stop mode.
•
MSCAN08 interrupt — MSCAN08 bus activity can wake the MCU from CPU
stop. However, until the oscillator starts up and synchronization is achieved
the MSCAN08 will not respond to incoming data.
Upon exit from stop mode, the system clocks begin running after an oscillator
stabilization delay. A 12-bit stop recovery counter inhibits the system clocks for
4096 CGMXCLK cycles after the reset or external interrupt.
The short stop recovery bit, SSREC, in the CONFIG1 register controls the oscillator
stabilization delay during stop recovery. Setting SSREC reduces stop recovery
time from 4096 CGMXCLK cycles to 32 CGMXCLK cycles.
NOTE:
Use the full stop recovery time (SSREC = 0) in applications that use an external
crystal unless the OSCENINSTOP bit is set.
Data Sheet
140
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Low-Power Modes
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 11. Low-Voltage Inhibit (LVI)
11.1 Introduction
11.2 Features
This section describes the low-voltage inhibit (LVI) module, which monitors the
voltage on the VDD pin and can force a reset when the VDD voltage falls below the
LVI trip falling voltage, VTRIPF
.
Features of the LVI module include:
•
•
•
Programmable LVI reset
Selectable LVI trip voltage
Programmable stop mode operation
11.3 Functional Description
Figure 11-1 shows the structure of the LVI module. The LVI is enabled out of reset.
The LVI module contains a bandgap reference circuit and comparator. Clearing the
LVI power disable bit, LVIPWRD, enables the LVI to monitor VDD voltage. Clearing
the LVI reset disable bit, LVIRSTD, enables the LVI module to generate a reset
when VDD falls below a voltage, VTRIPF. Setting the LVI enable in stop mode bit,
LVISTOP, enables the LVI to operate in stop mode. Setting the LVI 5-V or 3-V trip
point bit, LVI5OR3, enables the trip point voltage, VTRIPF, to be configured for
5-V operation. Clearing the LVI5OR3 bit enables the trip point voltage, VTRIPF
,
to be configured for 3-V operation. The actual trip points are shown in Section 21.
Electrical Specifications.
NOTE:
After a power-on reset (POR) the LVI’s default mode of operation is 3 V. If a 5-V
system is used, the user must set the LVI5OR3 bit to raise the trip point to 5-V
operation. Note that this must be done after every power-on reset since the default
will revert back to 3-V mode after each power-on reset. If the VDD supply is below
the 5-V mode trip voltage but above the 3-V mode trip voltage when POR is
released, the part will operate because VTRIPF defaults to 3-V mode after a POR.
So, in a 5-V system care must be taken to ensure that VDD is above the 5-V mode
trip voltage after POR is released.
If the user requires 5-V mode and sets the LVI5OR3 bit after a power-on reset while
the VDD supply is not above the VTRIPR for 5-V mode, the microcontroller unit
(MCU) will immediately go into reset. The LVI in this case will hold the part in reset
until either VDD goes above the rising 5-V trip point, VTRIPR, which will release reset
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
141
MOTOROLA
Low-Voltage Inhibit (LVI)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Low-Voltage Inhibit (LVI)
or VDD decreases to approximately 0 V which will re-trigger the power-on reset and
reset the trip point to 3-V operation.
LVISTOP, LVIPWRD, LVI5OR3, and LVIRSTD are in the configuration register
(CONFIG1). See Figure 5-2. Configuration Register 1 (CONFIG1) for details of
the LVI’s configuration bits. Once an LVI reset occurs, the MCU remains in reset
until VDD rises above a voltage, VTRIPR, which causes the MCU to exit reset. See
15.3.2.5 Low-Voltage Inhibit (LVI) Reset for details of the interaction between the
SIM and the LVI. The output of the comparator controls the state of the LVIOUT
flag in the LVI status register (LVISR).
An LVI reset also drives the RST pin low to provide low-voltage protection to
external peripheral devices.
VDD
STOP INSTRUCTION
LVISTOP
FROM CONFIG1
FROM CONFIG1
LVIRSTD
LVIPWRD
FROM CONFIG
VDD > LVITrip = 0
LVI RESET
LOW VDD
DETECTOR
VDD ≤ LVITrip = 1
LVIOUT
LVI5OR3
FROM CONFIG1
Figure 11-1. LVI Module Block Diagram
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Read: LVIOUT
0
0
0
0
0
0
0
LVI Status Register
(LVISR) Write:
See page 143.
$FE0C
Reset:
0
0
0
0
0
0
0
0
= Unimplemented
Figure 11-2. LVI I/O Register Summary
Data Sheet
142
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Low-Voltage Inhibit (LVI)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Low-Voltage Inhibit (LVI)
LVI Status Register
11.3.1 Polled LVI Operation
In applications that can operate at VDD levels below the VTRIPF level, software can
monitor VDD by polling the LVIOUT bit. In the configuration register, the LVIPWRD
bit must be 0 to enable the LVI module, and the LVIRSTD bit must be 1 to disable
LVI resets.
11.3.2 Forced Reset Operation
In applications that require VDD to remain above the VTRIPF level, enabling LVI
resets allows the LVI module to reset the MCU when VDD falls below the VTRIPF
level. In the configuration register, the LVIPWRD and LVIRSTD bits must be
cleared to enable the LVI module and to enable LVI resets.
11.3.3 Voltage Hysteresis Protection
Once the LVI has triggered (by having VDD fall below VTRIPF), the LVI will maintain
a reset condition until VDD rises above the rising trip point voltage, VTRIPR. This
prevents a condition in which the MCU is continually entering and exiting reset if
VDD is approximately equal to VTRIPF. VTRIPR is greater than VTRIPF by the
hysteresis voltage, VHYS
.
11.3.4 LVI Trip Selection
The LVI5OR3 bit in the configuration register selects whether the LVI is configured
for 5-V or 3-V protection.
NOTE:
The microcontroller is guaranteed to operate at a minimum supply voltage. The trip
point (VTRIPF [5 V] or VTRIPF [3 V]) may be lower than this. See Section 21.
Electrical Specifications for the actual trip point voltages.
11.4 LVI Status Register
The LVI status register (LVISR) indicates if the VDD voltage was detected below
the VTRIPF level.
Address: $FE0C
Bit 7
6
0
5
0
4
0
3
0
2
0
1
0
Bit 0
0
Read: LVIOUT
Write:
Reset:
0
0
0
0
0
0
0
0
= Unimplemented
Figure 11-3. LVI Status Register (LVISR)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
143
MOTOROLA
Low-Voltage Inhibit (LVI)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Low-Voltage Inhibit (LVI)
LVIOUT — LVI Output Bit
This read-only flag becomes set when the VDD voltage falls below the VTRIPF
trip voltage (see Table 11-1). Reset clears the LVIOUT bit.
Table 11-1. LVIOUT Bit Indication
VDD
LVIOUT
VDD > VTRIPR
0
VDD < VTRIPF
1
VTRIPF < VDD < VTRIPR
Previous value
11.5 LVI Interrupts
The LVI module does not generate interrupt requests.
11.6 Low-Power Modes
The STOP and WAIT instructions put the MCU in low power-consumption standby
modes.
11.6.1 Wait Mode
11.6.2 Stop Mode
If enabled, the LVI module remains active in wait mode. If enabled to generate
resets, the LVI module can generate a reset and bring the MCU out of wait mode.
If enabled in stop mode (LVISTOP bit in the configuration register is set), the LVI
module remains active in stop mode. If enabled to generate resets, the LVI module
can generate a reset and bring the MCU out of stop mode.
Data Sheet
144
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Low-Voltage Inhibit (LVI)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 12. MSCAN08 Controller (MSCAN08)
12.1 Introduction
The MSCAN08 is the specific implementation of the Motorola scalable controller
area network (MSCAN) concept targeted for the Motorola M68HC08
Microcontroller Family.
The module is a communication controller implementing the CAN 2.0 A/B protocol
as defined in the BOSCH specification dated September, 1991.
The CAN protocol was primarily, but not exclusively, designed to be used as a
vehicle serial data bus, meeting the specific requirements of this field: real-time
processing, reliable operation in the electromagnetic interference (EMI)
environment of a vehicle, cost-effectiveness, and required bandwidth.
MSCAN08 utilizes an advanced buffer arrangement, resulting in a predictable
real-time behavior, and simplifies the application software.
12.2 Features
Basic features of the MSCAN08 are:
•
MSCAN08 enable is software controlled by bit (MSCANEN) in configuration
register (CONFIG2)
•
•
Modular architecture
Implementation of the CAN Protocol — Version 2.0A/B
–
–
–
Standard and extended data frames
0–8 bytes data length.
Programmable bit rate up to 1 Mbps depending on the actual bit timing
and the clock jitter of the phase-locked loop (PLL)
•
•
•
Support for remote frames
Double-buffered receive storage scheme
Triple-buffered transmit storage scheme with internal prioritization using a
“local priority” concept
•
Flexible maskable identifier filter supports alternatively one full size
extended identifier filter or two 16-bit filters or four 8-bit filters
•
•
•
Programmable wakeup functionality with integrated low-pass filter
Programmable loop-back mode supports self-test operation
Separate signalling and interrupt capabilities for all CAN receiver and
transmitter error states (warning, error passive, bus off)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
145
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
P O R T B
D D R B
F R T P O
D D R F
P O R
R G D D
P O R T A
R A D D
P O R T C
D D R C
E T R P O
D D R
P O R T D
D D R D
E
Data Sheet
146
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
External Pins
•
•
•
Programmable MSCAN08 clock source either CPU bus clock or crystal
oscillator output
Programmable link to timer interface module 2 channel 0 for time-stamping
and network synchronization
Low-power sleep mode
12.3 External Pins
The MSCAN08 uses two external pins, one input (CANRX) and one output
(CANTX). The CANTX output pin represents the logic level on the CAN: 0 is for a
dominant state, and 1 is for a recessive state.
A typical CAN system with MSCAN08 is shown in Figure 12-2.
Each CAN station is connected physically to the CAN bus lines through a
transceiver chip. The transceiver is capable of driving the large current needed for
the CAN and has current protection against defected CAN or defected stations.
CAN STATION 1
CAN NODE 1
CAN NODE 2
CAN NODE N
MCU
CAN CONTROLLER
(MSCAN08)
CANTX
CANRX
TRANSCEIVER
CAN_L
CAN_H
C A N BUS
Figure 12-2. The CAN System
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
147
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
12.4 Message Storage
MSCAN08 facilitates a sophisticated message storage system which addresses
the requirements of a broad range of network applications.
12.4.1 Background
Modern application layer software is built under two fundamental assumptions:
1. Any CAN node is able to send out a stream of scheduled messages without
releasing the bus between two messages. Such nodes will arbitrate for the
bus right after sending the previous message and will only release the bus
in case of lost arbitration.
2. The internal message queue within any CAN node is organized as such that
the highest priority message will be sent out first if more than one message
is ready to be sent.
Above behavior cannot be achieved with a single transmit buffer. That buffer must
be reloaded right after the previous message has been sent. This loading process
lasts a definite amount of time and has to be completed within the inter-frame
sequence (IFS) to be able to send an uninterrupted stream of messages. Even if
this is feasible for limited CAN bus speeds, it requires that the CPU reacts with
short latencies to the transmit interrupt.
A double buffer scheme would de-couple the re-loading of the transmit buffers from
the actual message being sent and as such reduces the reactiveness requirements
on the CPU. Problems may arise if the sending of a message would be finished just
while the CPU re-loads the second buffer. In that case, no buffer would then be
ready for transmission and the bus would be released.
At least three transmit buffers are required to meet the first of the above
requirements under all circumstances. The MSCAN08 has three transmit buffers.
The second requirement calls for some sort of internal prioritization which the
MSCAN08 implements with the “local priority” concept described in 12.4.2 Receive
Structures.
12.4.2 Receive Structures
The received messages are stored in a 2-stage input first in first out (FIFO). The
two message buffers are mapped using a "ping pong" arrangement into a single
memory area (see Figure 12-3). While the background receive buffer (RxBG) is
exclusively associated to the MSCAN08, the foreground receive buffer (RxFG) is
addressable by the central processor unit (CPU08). This scheme simplifies the
handler software, because only one address area is applicable for the receive
process.
Data Sheet
148
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Message Storage
CPU08 I BUS
MSCAN08
RxBG
RxFG
RXF
TXE
Tx0
Tx1
Tx2
PRIO
TXE
PRIO
TXE
PRIO
Figure 12-3. User Model for Message Buffer Organization
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
149
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Both buffers have a size of 13 bytes to store the CAN control bits, the identifier
(standard or extended), and the data content. For details, see 12.12
Programmer’s Model of Message Storage.
The receiver full flag (RXF) in the MSCAN08 receiver flag register (CRFLG),
signals the status of the foreground receive buffer. When the buffer contains a
correctly received message with matching identifier, this flag is set. See 12.13.5
MSCAN08 Receiver Flag Register (CRFLG)
On reception, each message is checked to see if it passes the filter (for details see
12.5 Identifier Acceptance Filter) and in parallel is written into RxBG. The
MSCAN08 copies the content of RxBG into RxFG(1), sets the RXF flag, and
generates a receive interrupt to the CPU(2). The user’s receive handler has to read
the received message from RxFG and to reset the RXF flag to acknowledge the
interrupt and to release the foreground buffer. A new message which can follow
immediately after the IFS field of the CAN frame, is received into RxBG. The
overwriting of the background buffer is independent of the identifier filter function.
When the MSCAN08 module is transmitting, the MSCAN08 receives its own
messages into the background receive buffer, RxBG. It does NOT overwrite RxFG,
generate a receive interrupt or acknowledge its own messages on the CAN bus.
The exception to this rule is in loop-back mode (see 12.13.2 MSCAN08 Module
Control Register 1), where the MSCAN08 treats its own messages exactly like all
other incoming messages. The MSCAN08 receives its own transmitted messages
in the event that it loses arbitration. If arbitration is lost, the MSCAN08 must be
prepared to become the receiver.
An overrun condition occurs when both the foreground and the background receive
message buffers are filled with correctly received messages with accepted
identifiers and another message is correctly received from the bus with an
accepted identifier. The latter message will be discarded and an error interrupt with
overrun indication will be generated if enabled. The MSCAN08 is still able to
transmit messages with both receive message buffers filled, but all incoming
messages are discarded.
12.4.3 Transmit Structures
The MSCAN08 has a triple transmit buffer scheme to allow multiple messages to
be set up in advance and to achieve an optimized real-time performance. The three
buffers are arranged as shown in Figure 12-3.
All three buffers have a 13-byte data structure similar to the outline of the receive
buffers (see 12.12 Programmer’s Model of Message Storage). An additional
transmit buffer priority register (TBPR) contains an 8-bit “local priority” field (PRIO)
(see 12.12.5 Transmit Buffer Priority Registers).
1. Only if the RXF flag is not set.
2. The receive interrupt will occur only if not masked. A polling scheme can be applied on RXF also.
Data Sheet
150
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Identifier Acceptance Filter
To transmit a message, the CPU08 has to identify an available transmit buffer
which is indicated by a set transmit buffer empty (TXE) flag in the MSCAN08
transmitter flag register (CTFLG) (see 12.13.7 MSCAN08 Transmitter Flag
Register).
The CPU08 then stores the identifier, the control bits and the data content into one
of the transmit buffers. Finally, the buffer has to be flagged ready for transmission
by clearing the TXE flag.
The MSCAN08 then will schedule the message for transmission and will signal the
successful transmission of the buffer by setting the TXE flag. A transmit interrupt is
generated(1) when TXE is set and can be used to drive the application software to
re-load the buffer.
In case more than one buffer is scheduled for transmission when the CAN bus
becomes available for arbitration, the MSCAN08 uses the local priority setting of
the three buffers for prioritization. For this purpose, every transmit buffer has an
8-bit local priority field (PRIO). The application software sets this field when the
message is set up. The local priority reflects the priority of this particular message
relative to the set of messages being emitted from this node. The lowest binary
value of the PRIO field is defined as the highest priority.
The internal scheduling process takes place whenever the MSCAN08 arbitrates for
the bus. This is also the case after the occurrence of a transmission error.
When a high priority message is scheduled by the application software, it may
become necessary to abort a lower priority message being set up in one of the
three transmit buffers. As messages that are already under transmission cannot be
aborted, the user has to request the abort by setting the corresponding abort
request flag (ABTRQ) in the transmission control register (CTCR). The MSCAN08
will then grant the request, if possible, by setting the corresponding abort request
acknowledge (ABTAK) and the TXE flag in order to release the buffer and by
generating a transmit interrupt. The transmit interrupt handler software can tell from
the setting of the ABTAK flag whether the message was actually aborted
(ABTAK = 1) or sent (ABTAK = 0).
12.5 Identifier Acceptance Filter
The identifier acceptance registers (CIDAR0–CIDAR3) define the acceptance
patterns of the standard or extended identifier (ID10–ID0 or ID28–ID0). Any of
these bits can be marked ‘don’t care’ in the identifier mask registers
(CIDMR0–CIDMR3).
1. The transmit interrupt will occur only if not masked. A polling scheme can be applied on TXE also.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
151
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
A filter hit is indicated to the application on software by a set RXF (receive buffer
full flag, see 12.13.5 MSCAN08 Receiver Flag Register (CRFLG)) and two bits in
the identifier acceptance control register (see 12.13.9 MSCAN08 Identifier
Acceptance Control Register). These identifier hit flags (IDHIT1 and IDHIT0)
clearly identify the filter section that caused the acceptance. They simplify the
application software’s task to identify the cause of the receiver interrupt. In case
that more than one hit occurs (two or more filters match) the lower hit has priority.
A very flexible programmable generic identifier acceptance filter has been
introduced to reduce the CPU interrupt loading. The filter is programmable to
operate in four different modes:
1. Single identifier acceptance filter, each to be applied to a) the full 29 bits of
the extended identifier and to the following bits of the CAN frame: RTR, IDE,
SRR or b) the 11 bits of the standard identifier plus the RTR and IDE bits of
CAN 2.0A/B messages. This mode implements a single filter for a full length
CAN 2.0B compliant extended identifier. Figure 12-4 shows how the 32-bit
filter bank (CIDAR0-3, CIDMR0-3) produces a filter 0 hit.
2. Two identifier acceptance filters, each to be applied to:
a. The 14 most significant bits of the extended identifier plus the SRR and
the IDE bits of CAN2.0B messages, or
b. The 11 bits of the identifier plus the RTR and IDE bits of CAN 2.0A/B
messages.
Figure 12-5 shows how the 32-bit filter bank (CIDAR0–CIDAR3 and
CIDMR0–CIDMR3) produces filter 0 and 1 hits.
3. Four identifier acceptance filters, each to be applied to the first eight bits of
the identifier. This mode implements four independent filters for the first
eight bits of a CAN 2.0A/B compliant standard identifier. Figure 12-6 shows
how the 32-bit filter bank (CIDAR0–CIDAR3 and CIDMR0–CIDMR3)
produces filter 0 to 3 hits.
4. Closed filter. No CAN message will be copied into the foreground buffer
RxFG, and the RXF flag will never be set.
Data Sheet
152
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Identifier Acceptance Filter
ID28
ID10
IDR0
IDR0
ID21 ID20
ID3 ID2
IDR1
ID15 ID14
IDR2
ID7 ID6
IDR3
RTR
IDR1 IDE
AM7
AC7
CIDMR0
CIDAR0
AM0 AM7
AC0 AC7
CIDMR1
CIDAR1
AM0 AM7
AC0 AC7
CIDMR2
CIDAR2
AM0 AM7
AC0 AC7
CIDMR3
CIDAR3
AM0
AC0
ID Accepted (Filter 0 Hit)
Figure 12-4. Single 32-Bit Maskable Identifier Acceptance Filter
ID28
ID10
IDR0
IDR0
ID21 ID20
ID3 ID2
IDR1
ID15 ID14
IDR2
ID7 ID6
IDR3
RTR
IDR1 IDE
AM7
AC7
CIDMR0
CIDAR0
AM0 AM7
AC0 AC7
CIDMR1
CIDAR1
AM0
AC0
ID ACCEPTED (FILTER 0 HIT)
AM7
AC7
CIDMR2
AM0 AM7
AC0 AC7
CIDMR3
AM0
AC0
CIDAR2
CIDAR3
ID ACCEPTED (FILTER 1 HIT)
Figure 12-5. Dual 16-Bit Maskable Acceptance Filters
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
153
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
ID28
ID10
IDR0
IDR0
ID21 ID20
ID3 ID2
IDR1
IDR1
ID15 ID14
IDE
IDR2
ID7 ID6
IDR3
RTR
AM7
AC7
CIDMR0
CIDAR0
AM0
AC0
ID ACCEPTED (FILTER 0 HIT)
AM7
AC7
CIDMR1
CIDAR1
AM0
AC0
ID ACCEPTED (FILTER 1 HIT)
AM7
AC7
CIDMR2
CIDAR2
AM0
AC0
ID ACCEPTED (FILTER 2 HIT)
AM7
AC7
CIDMR3
CIDAR3
AM0
AC0
ID ACCEPTED (FILTER 3 HIT)
Figure 12-6. Quadruple 8-Bit Maskable Acceptance Filters
Data Sheet
154
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Interrupts
12.6 Interrupts
The MSCAN08 supports four interrupt vectors mapped onto eleven different
interrupt sources, any of which can be individually masked. For details, see 12.13.5
MSCAN08 Receiver Flag Register (CRFLG) through 12.13.8 MSCAN08
Transmitter Control Register.
1. Transmit Interrupt: At least one of the three transmit buffers is empty (not
scheduled) and can be loaded to schedule a message for transmission. The
TXE flags of the empty message buffers are set.
2. Receive Interrupt: A message has been received successfully and loaded
into the foreground receive buffer. This interrupt will be emitted immediately
after receiving the EOF symbol. The RXF flag is set.
3. Wakeup Interrupt: An activity on the CAN bus occurred during MSCAN08
internal sleep mode or power-down mode (provided SLPAK = WUPIE = 1).
4. Error Interrupt: An overrun, error, or warning condition occurred. The
receiver flag register (CRFLG) will indicate one of the following conditions:
–
–
–
–
–
–
Overrun: An overrun condition as described in 12.4.2 Receive
Structures, has occurred.
Receiver Warning: The receive error counter has reached the CPU
warning limit of 96.
Transmitter Warning: The transmit error counter has reached the CPU
warning limit of 96.
Receiver Error Passive: The receive error counter has exceeded the
error passive limit of 127 and MSCAN08 has gone to error passive state.
Transmitter Error Passive: The transmit error counter has exceeded the
error passive limit of 127 and MSCAN08 has gone to error passive state.
Bus Off: The transmit error counter has exceeded 255 and MSCAN08
has gone to bus off state.
12.6.1 Interrupt Acknowledge
Interrupts are directly associated with one or more status flags in either the
MSCAN08 receiver flag register (CRFLG) or the MSCAN08 transmitter flag register
(CTFLG). Interrupts are pending as long as one of the corresponding flags is set.
The flags in the above registers must be reset within the interrupt handler in order
to handshake the interrupt. The flags are reset through writing a ‘1’ to the
corresponding bit position. A flag cannot be cleared if the respective condition still
prevails.
NOTE:
Bit manipulation instructions (BSET) shall not be used to clear interrupt flags.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
155
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
12.6.2 Interrupt Vectors
The MSCAN08 supports four interrupt vectors as shown in Table 12-1. The vector
addresses and the relative interrupt priority are dependent on the chip integration
and to be defined.
Table 12-1. MSCAN08 Interrupt Vector Addresses
Local
Mask
Global
Mask
Function
Source
Wakeup
WUPIF
RWRNIF
TWRNIF
RERRIF
TERRIF
BOFFIF
OVRIF
RXF
WUPIE
RWRNIE
TWRNIE
RERRIE
TERRIE
BOFFIE
OVRIE
Error interrupts
I bit
Receive
Transmit
RXFIE
TXE0
TXEIE0
TXEIE1
TXEIE2
TXE1
TXE2
12.7 Protocol Violation Protection
The MSCAN08 will protect the user from accidentally violating the CAN protocol
through programming errors. The protection logic implements the following
features:
•
The receive and transmit error counters cannot be written or otherwise
manipulated.
•
All registers which control the configuration of the MSCAN08 can not
be modified while the MSCAN08 is on-line. The SFTRES bit in the
MSCAN08 module control register (see 12.13.1 MSCAN08 Module
Control Register 0) serves as a lock to protect the following registers:
–
–
–
–
–
MSCAN08 module control register 1 (CMCR1)
MSCAN08 bus timing register 0 and 1 (CBTR0 and CBTR1)
MSCAN08 identifier acceptance control register (CIDAC)
MSCAN08 identifier acceptance registers (CIDAR0–3)
MSCAN08 identifier mask registers (CIDMR0–3)
•
The CANTX pin is forced to recessive when the MSCAN08 is in any of the
low-power modes.
Data Sheet
156
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Low-Power Modes
12.8 Low-Power Modes
In addition to normal mode, the MSCAN08 has three modes with reduced power
consumption: sleep, soft reset, and power down. In sleep and soft reset mode,
power consumption is reduced by stopping all clocks except those to access the
registers. In power-down mode, all clocks are stopped and no power is consumed.
The WAIT and STOP instructions put the MCU in low-power consumption stand-by
modes. Table 12-2 summarizes the combinations of MSCAN08 and CPU modes.
A particular combination of modes is entered for the given settings of the bits
SLPAK and SFTRES. For all modes, an MSCAN08 wakeup interrupt can occur
only if SLPAK = WUPIE = 1.
.
Table 12-2. MSCAN08 versus CPU Operating Modes
CPU Mode
MSCAN08 Mode
STOP
WAIT or RUN
SLPAK = X(1)
SFTRES = X
Power Down
Sleep
SLPAK = 1
SFTRES = 0
SLPAK = 0
SFTRES = 1
Soft Reset
SLPAK = 0
SFTRES = 0
Normal
1. ‘X’ means don’t care.
12.8.1 MSCAN08 Sleep Mode
The CPU can request the MSCAN08 to enter the low-power mode by asserting
the SLPRQ bit in the module configuration register (see
Figure 12-7). The time when the MSCAN08 enters sleep mode depends on its
activity:
•
•
•
If it is transmitting, it continues to transmit until there is no more message to
be transmitted, and then goes into sleep mode
If it is receiving, it waits for the end of this message and then goes into sleep
mode
If it is neither transmitting or receiving, it will immediately go into sleep mode
NOTE:
The application software must avoid setting up a transmission (by clearing or more
TXE flags) and immediately request sleep mode (by setting SLPRQ). It then
depends on the exact sequence of operations whether MSCAN08 starts
transmitting or goes into sleep mode directly.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
157
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
During sleep mode, the SLPAK flag is set. The application software should use
SLPAK as a handshake indication for the request (SLPRQ) to go into sleep mode.
When in sleep mode, the MSCAN08 stops its internal clocks. However, clocks to
allow register accesses still run. If the MSCAN08 is in bus-off state, it stops
counting the 128*11 consecutive recessive bits due to the stopped clocks. The
CANTX pin stays in recessive state. If RXF = 1, the message can be read and RXF
can be cleared. Copying of RxGB into RxFG doesn’t take place while in sleep
mode. It is possible to access the transmit buffers and to clear the TXE flags. No
message abort takes place while in sleep mode.
The MSCAN08 leaves sleep mode (wakes-up) when:
•
•
•
Bus activity occurs, or
The MCU clears the SLPRQ bit, or
The MCU sets the SFTRES bit
MSCAN08 RUNNING
MCU
or MSCAN08
SLPRQ = 0
SLPAK = 0
MCU
MSCAN08 SLEEPING
SLEEP REQUEST
SLPRQ = 1
SLPAK = 1
SLPRQ = 1
SLPAK = 0
MSCAN08
Figure 12-7. Sleep Request/Acknowledge Cycle
NOTE:
The MCU cannot clear the SLPRQ bit before the MSCAN08 is in sleep mode
(SLPAK=1).
After wakeup, the MSCAN08 waits for 11 consecutive recessive bits to synchronize
to the bus. As a consequence, if the MSCAN08 is woken-up by a CAN frame, this
frame is not received. The receive message buffers (RxFG and RxBG) contain
messages if they were received before sleep mode was entered. All pending
actions are executed upon wakeup: copying of RxBG into RxFG, message aborts
and message transmissions. If the MSCAN08 is still in bus-off state after sleep
mode was left, it continues counting the 128*11 consecutive recessive bits.
Data Sheet
158
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Low-Power Modes
12.8.2 MSCAN08 Soft Reset Mode
In soft reset mode, the MSCAN08 is stopped. Registers can still be accessed. This
mode is used to initialize the module configuration, bit timing and the CAN
message filter. See 12.13.1 MSCAN08 Module Control Register 0 for a complete
description of the soft reset mode.
When setting the SFTRES bit, the MSCAN08 immediately stops all ongoing
transmissions and receptions, potentially causing CAN protocol violations.
NOTE:
The user is responsible to take care that the MSCAN08 is not active when soft reset
mode is entered. The recommended procedure is to bring the MSCAN08 into sleep
mode before the SFTRES bit is set.
12.8.3 MSCAN08 Power-Down Mode
The MSCAN08 is in power-down mode when the CPU is in stop mode.
When entering the power-down mode, the MSCAN08 immediately stops all
ongoing transmissions and receptions, potentially causing CAN protocol violations.
NOTE:
The user is responsible to take care that the MSCAN08 is not active when
power-down mode is entered. The recommended procedure is to bring the
MSCAN08 into sleep mode before the STOP instruction is executed.
To protect the CAN bus system from fatal consequences resulting from violations
of the above rule, the MSCAN08 drives the CANTX pin into recessive state.
In power-down mode, no registers can be accessed.
MSCAN08 bus activity can wake the MCU from CPU stop/MSCAN08 power-down
mode. However, until the oscillator starts up and synchronization is achieved the
MSCAN08 will not respond to incoming data.
12.8.4 CPU Wait Mode
The MSCAN08 module remains active during CPU wait mode. The MSCAN08 will
stay synchronized to the CAN bus and generates transmit, receive, and error
interrupts to the CPU, if enabled. Any such interrupt will bring the MCU out of wait
mode.
12.8.5 Programmable Wakeup Function
The MSCAN08 can be programmed to apply a low-pass filter function to the
CANRX input line while in internal sleep mode (see information on control bit
WUPM in 12.13.2 MSCAN08 Module Control Register 1). This feature can be
used to protect the MSCAN08 from wakeup due to short glitches on the CAN bus
lines. Such glitches can result from electromagnetic inference within noisy
environments.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
159
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
12.9 Timer Link
The MSCAN08 will generate a timer signal whenever a valid frame has been
received. Because the CAN specification defines a frame to be valid if no errors
occurred before the EOF field has been transmitted successfully, the timer signal
will be generated right after the EOF. A pulse of one bit time is generated. As the
MSCAN08 receiver engine also receives the frames being sent by itself, a timer
signal also will be generated after a successful transmission.
The previously described timer signal can be routed into the on-chip timer interface
module (TIM). This signal is connected to channel 0 of timer interface module 2
(TIM2) under the control of the timer link enable (TLNKEN) bit in CMCR0.
After timer n has been programmed to capture rising edge events, it can be used
under software control to generate 16-bit time stamps which can be stored with the
received message.
12.10 Clock System
Figure 12-8 shows the structure of the MSCAN08 clock generation circuitry and its
interaction with the clock generation module (CGM). With this flexible clocking
scheme the MSCAN08 is able to handle CAN bus rates ranging from 10 kbps up
to 1 Mbps.
CGMXCLK
OSC
÷ 2
CGMOUT
(TO SIM)
BCS
PLL
÷ 2
CGM
MSCAN08
(2 * BUS FREQUENCY)
÷ 2
MSCANCLK
PRESCALER
(1 ... 64)
CLKSRC
Figure 12-8. Clocking Scheme
Data Sheet
160
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Clock System
The clock source bit (CLKSRC) in the MSCAN08 module control register (CMCR1)
(see 12.13.1 MSCAN08 Module Control Register 0) defines whether the
MSCAN08 is connected to the output of the crystal oscillator or to the PLL output.
The clock source has to be chosen such that the tight oscillator tolerance
requirements (up to 0.4%) of the CAN protocol are met.
NOTE:
If the system clock is generated from a PLL, it is recommended to select the crystal
clock source rather than the system clock source due to jitter considerations,
especially at faster CAN bus rates.
A programmable prescaler is used to generate out of the MSCAN08 clock the time
quanta (Tq) clock. A time quantum is the atomic unit of time handled by the
MSCAN08.
fMSCANCLK
fTq
=
Presc value
A bit time is subdivided into three segments(1) (see Figure 12-9):
•
•
SYNC_SEG: This segment has a fixed length of one time quantum. Signal
edges are expected to happen within this section.
Time segment 1: This segment includes the PROP_SEG and the
PHASE_SEG1 of the CAN standard. It can be programmed by setting the
parameter TSEG1 to consist of 4 to 16 time quanta.
•
Time segment 2: This segment represents PHASE_SEG2 of the CAN
standard. It can be programmed by setting the TSEG2 parameter to be 2 to
8 time quanta long.
fTq
Bit rate =
No. of time quanta
The synchronization jump width (SJW) can be programmed in a range of 1 to 4 time
quanta by setting the SJW parameter.
The above parameters can be set by programming the bus timing registers,
CBTR0 and CBTR1. See 12.13.3 MSCAN08 Bus Timing Register 0 and 12.13.4
MSCAN08 Bus Timing Register 1.
NOTE:
It is the user’s responsibility to make sure that the bit timing settings are in
compliance with the CAN standard,
Table 12-8 gives an overview on the CAN conforming segment settings and the
related parameter values.
1. For further explanation of the underlying concepts please refer to ISO/DIS 11 519-1,
Section 10.3.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
161
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
NRZ SIGNAL
SYNC
_SEG
TIME SEGMENT 1
(PROP_SEG + PHASE_SEG1)
TIME SEG. 2
(PHASE_SEG2)
1
4 ... 16
2 ... 8
8... 25 TIME QUANTA
= 1 BIT TIME
SAMPLE POINT
(SINGLE OR TRIPLE SAMPLING)
Figure 12-9. Segments Within the Bit Time
.
Table 12-3. Time Segment Syntax
System expects transitions to occur on the bus during this
period.
SYNC_SEG
A node in transmit mode will transfer a new value to the CAN
bus at this point.
Transmit point
A node in receive mode will sample the bus at this point. If the
Sample point three samples per bit option is selected then this point marks
the position of the third sample.
Table 12-4. CAN Standard Compliant Bit Time Segment Settings
Time
Segment 1
Time
Segment 2
Synchronized
Jump Width
TSEG1
TSEG2
SJW
5 .. 10
4 .. 11
5 .. 12
6 .. 13
7 .. 14
8 .. 15
9 .. 16
4 .. 9
3 .. 10
4 .. 11
5 .. 12
6 .. 13
7 .. 14
8 .. 15
2
3
4
5
6
7
8
1
2
3
4
5
6
7
1 .. 2
1 .. 3
1 .. 4
1 .. 4
1 .. 4
1 .. 4
1 .. 4
0 .. 1
0 .. 2
0 .. 3
0 .. 3
0 .. 3
0 .. 3
0 .. 3
Data Sheet
162
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Memory Map
12.11 Memory Map
The MSCAN08 occupies 128 bytes in the CPU08 memory space. The absolute
mapping is implementation dependent with the base address being a multiple
of 128.
$0500
CONTROL REGISTERS
9 BYTES
$0508
$0509
RESERVED
5 BYTES
$050D
$050E
ERROR COUNTERS
2 BYTES
$050F
$0510
IDENTIFIER FILTER
8 BYTES
$0517
$0518
RESERVED
40 BYTES
$053F
$0540
RECEIVE BUFFER
$054F
$0550
TRANSMIT BUFFER 0
$055F
$0560
TRANSMIT BUFFER 1
$056F
$0570
TRANSMIT BUFFER 2
$057F
Figure 12-10. MSCAN08 Memory Map
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
163
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
12.12 Programmer’s Model of Message Storage
This section details the organization of the receive and transmit message buffers
and the associated control registers. For reasons of programmer interface
simplification, the receive and transmit message buffers have the same outline.
Each message buffer allocates 16 bytes in the memory map containing a 13-byte
data structure. An additional transmit buffer priority register (TBPR) is defined for
the transmit buffers.
Addr(1)
Register Name
$05b0
$05b1
$05b2
$05b3
$05b4
$05b5
$05b6
$05b7
$05b8
$05b9
$05bA
$05bB
$05bC
$05bD
$05bE
$05bF
IDENTIFIER REGISTER 0
IDENTIFIER REGISTER 1
IDENTIFIER REGISTER 2
IDENTIFIER REGISTER 3
DATA SEGMENT REGISTER 0
DATA SEGMENT REGISTER 1
DATA SEGMENT REGISTER 2
DATA SEGMENT REGISTER 3
DATA SEGMENT REGISTER 4
DATA SEGMENT REGISTER 5
DATA SEGMENT REGISTER 6
DATA SEGMENT REGISTER 7
DATA LENGTH REGISTER
TRANSMIT BUFFER PRIORITY REGISTER(2)
UNUSED
UNUSED
1. Where b equals the following:
b = 4 for receive buffer
b = 5 for transmit buffer 0
b = 6 for transmit buffer 1
b = 7 for transmit buffer 2
2. Not applicable for receive buffers
Figure 12-11. Message Buffer Organization
Data Sheet
164
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Message Storage
12.12.1 Message Buffer Outline
Figure 12-12 shows the common 13-byte data structure of receive and transmit
buffers for extended identifiers. The mapping of standard identifiers into the IDR
registers is shown in Figure 12-13. All bits of the 13-byte data structure are
undefined out of reset.
NOTE:
The foreground receive buffer can be read anytime but cannot be written. The
transmit buffers can be read or written anytime.
Addr.
Register
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
$05b0
IDR0
ID28
ID27
ID26
ID25
ID24
ID23
ID22
ID21
Read:
Write:
$05b1
$05b2
$05b3
$05b4
$05b5
$05b6
$05b7
$05b8
$05b9
$05bA
$05bB
$05bC
IDR1
IDR2
ID20
ID14
ID6
ID19
ID13
ID5
ID18
ID12
ID4
SRR (=1)
ID11
ID3
IDE (=1)
ID10
ID2
ID17
ID9
ID16
ID8
ID15
ID7
Read:
Write:
Read:
Write:
IDR3
ID1
ID0
RTR
DB0
DB0
DB0
DB0
DB0
DB0
DB0
DB0
DLC0
Read:
Write:
DSR0
DSR1
DSR2
DSR3
DSR4
DSR5
DSR6
DSR7
DLR
DB7
DB7
DB7
DB7
DB7
DB7
DB7
DB7
DB6
DB6
DB6
DB6
DB6
DB6
DB6
DB6
DB5
DB5
DB5
DB5
DB5
DB5
DB5
DB5
DB4
DB4
DB4
DB4
DB4
DB4
DB4
DB4
DB3
DB3
DB3
DB3
DB3
DB3
DB3
DB3
DLC3
DB2
DB2
DB2
DB2
DB2
DB2
DB2
DB2
DLC2
DB1
DB1
DB1
DB1
DB1
DB1
DB1
DB1
DLC1
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
= Unimplemented
Figure 12-12. Receive/Transmit Message Buffer Extended Identifier (IDRn)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
165
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Addr.
Register
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
$05b0
IDR0
IDR1
IDR2
IDR3
ID10
ID9
ID8
ID7
ID6
ID5
ID4
ID3
Read:
Write:
$05b1
$05b2
$05b3
ID2
ID1
ID0
RTR
IDE (=0)
Read:
Write:
Read:
Write:
= Unimplemented
Figure 12-13. Standard Identifier Mapping
12.12.2 Identifier Registers
The identifiers consist of either 11 bits (ID10–ID0) for the standard, or 29 bits
(ID28–ID0) for the extended format. ID10/28 is the most significant bit and is
transmitted first on the bus during the arbitration procedure. The priority of an
identifier is defined to be highest for the smallest binary number.
SRR — Substitute Remote Request
This fixed recessive bit is used only in extended format. It must be set to 1 by
the user for transmission buffers and will be stored as received on the CAN bus
for receive buffers.
IDE — ID Extended
This flag indicates whether the extended or standard identifier format is applied
in this buffer. In case of a receive buffer, the flag is set as being received and
indicates to the CPU how to process the buffer identifier registers. In case of a
transmit buffer, the flag indicates to the MSCAN08 what type of identifier to
send.
1 = Extended format, 29 bits
0 = Standard format, 11 bits
RTR — Remote Transmission Request
This flag reflects the status of the remote transmission request bit in the CAN
frame. In case of a receive buffer, it indicates the status of the received frame
and supports the transmission of an answering frame in software. In case of a
transmit buffer, this flag defines the setting of the RTR bit to be sent.
1 = Remote frame
0 = Data frame
Data Sheet
166
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Message Storage
12.12.3 Data Length Register (DLR)
This register keeps the data length field of the CAN frame.
DLC3–DLC0 — Data Length Code Bits
The data length code contains the number of bytes (data byte count) of the
respective message. At transmission of a remote frame, the data length code is
transmitted as programmed while the number of transmitted bytes is always 0.
The data byte count ranges from 0 to 8 for a data frame. Table 12-5 shows the
effect of setting the DLC bits.
Table 12-5. Data Length Codes
Data Length Code
Data Byte
Count
DLC3
DLC2
DLC1
DLC0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
0
1
2
3
4
5
6
7
8
12.12.4 Data Segment Registers (DSRn)
The eight data segment registers contain the data to be transmitted or received.
The number of bytes to be transmitted or being received is determined by the data
length code in the corresponding DLR.
12.12.5 Transmit Buffer Priority Registers
Address:
$05bD
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
PRIO7
PRIO6
PRIO5
PRIO4
PRIO3
PRIO2
PRIO1
PRIO0
Unaffected by reset
Figure 12-14. Transmit Buffer Priority Register (TBPR)
PRIO7–PRIO0 — Local Priority
This field defines the local priority of the associated message buffer. The local
priority is used for the internal prioritization process of the MSCAN08 and is
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
167
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
defined to be highest for the smallest binary number. The MSCAN08
implements the following internal prioritization mechanism:
•
•
•
All transmission buffers with a cleared TXE flag participate in the
prioritization right before the SOF is sent.
The transmission buffer with the lowest local priority field wins the
prioritization.
In case more than one buffer has the same lowest priority, the message
buffer with the lower index number wins.
12.13 Programmer’s Model of Control Registers
The programmer’s model has been laid out for maximum simplicity and efficiency.
Figure 12-15 gives an overview on the control register block of the MSCAN08.
Addr.
Register
CMCR0
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
0
0
0
SYNCH
SLPAK
$0500
TLNKEN
SLPRQ
SFTRES
Read:
Write:
0
0
0
0
0
$0501
$0502
$0503
$0504
$0505
$0506
$0507
$0508
$0509
$050E
CMCR1
CBTR0
CBTR1
CRFLG
CRIER
LOOPB
BRP2
WUPM
BRP1
CLKSRC
BRP0
Read:
Write:
SJW1
SAMP
WUPIF
SJW0
BRP5
BRP4
BRP3
TSEG13
TERRIF
Read:
Write:
TSEG22
RWRNIF
TSEG21
TWRNIF
TSEG20
RERRIF
TSEG12
BOFFIF
BOFFIE
TXE2
TSEG11
OVRIF
OVRIE
TXE1
TSEG10
RXF
Read:
Write:
Read:
Write:
WUPIE
0
RWRNIE
ABTAK2
TWRNIE
ABTAK1
RERRIE
ABTAK0
TERRIE
0
RXFIE
TXE0
Read:
Write:
CTFLG
CTCR
Read:
Write:
0
0
0
0
ABTRQ2
IDAM2
R
ABTRQ1
IDAM1
R
ABTRQ0
IDAM0
R
TXEIE2
IDHIT2
TXEIE1
IDHIT1
TXEIE0
IDHIT0
Read:
Write:
CIDAC
Read:
Write:
Reserved
CRXERR
R
R
R
R
R
Read:
Write:
RXERR7
RXERR6
RXERR5
RXERR4
RXERR3
R
RXERR2
RXERR1
RXERR0
= Unimplemented
= Reserved
Figure 12-15. MSCAN08 Control Register Structure
Data Sheet
168
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
Addr.
Register
CTXERR
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
$050F
TXERR7
TXERR6
TXERR5
TXERR4
TXERR3
TXERR2
TXERR1
TXERR0
Read:
Write:
$0510
$0511
$0512
$0513
$0514
$0515
$0516
$0517
CIDAR0
CIDAR1
CIDAR2
CIDAR3
CIDMR0
CIDMR1
CIDMR2
CIDMR3
AC7
AC7
AC7
AC7
AM7
AM7
AM7
AM7
AC6
AC6
AC6
AC6
AM6
AM6
AM6
AM6
AC5
AC5
AC5
AC5
AM5
AM5
AM5
AM5
AC4
AC4
AC4
AC4
AM4
AM4
AM4
AM4
AC3
AC3
AC3
AC3
AM3
AM3
AM3
AC2
AC2
AC2
AC2
AM2
AM2
AM2
AC1
AC1
AC1
AC1
AM1
AM1
AM1
AM1
AC0
AC0
AC0
AC0
AM0
AM0
AM0
AM0
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
AM3
R
AM2
= Unimplemented
= Reserved
Figure 12-15. MSCAN08 Control Register Structure (Continued)
12.13.1 MSCAN08 Module Control Register 0
Address: $0500
Bit 7
0
6
0
5
0
4
3
TLNKEN
0
2
1
SLPRQ
0
Bit 0
SFTRES
1
Read:
Write:
Reset:
SYNCH
SLPAK
0
0
0
0
0
= Unimplemented
Figure 12-16. Module Control Register 0 (CMCR0)
SYNCH — Synchronized Status
This bit indicates whether the MSCAN08 is synchronized to the CAN bus and
as such can participate in the communication process.
1 = MSCAN08 synchronized to the CAN bus
0 = MSCAN08 not synchronized to the CAN bus
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
169
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
TLNKEN — Timer Enable
This flag is used to establish a link between the MSCAN08 and the on-chip timer
(see 12.9 Timer Link).
1 = The MSCAN08 timer signal output is connected to the timer input.
0 = The port is connected to the timer input.
SLPAK — Sleep Mode Acknowledge
This flag indicates whether the MSCAN08 is in module internal sleep mode. It
shall be used as a handshake for the sleep mode request (see 12.8.1
MSCAN08 Sleep Mode). If the MSCAN08 detects bus activity while in sleep
mode, it clears the flag.
1 = Sleep – MSCAN08 in internal sleep mode
0 = Wakeup – MSCAN08 is not in sleep mode
SLPRQ — Sleep Request, Go to Internal Sleep Mode
This flag requests the MSCAN08 to go into an internal power-saving mode (see
12.8.1 MSCAN08 Sleep Mode).
1 = Sleep — The MSCAN08 will go into internal sleep mode.
0 = Wakeup — The MSCAN08 will function normally.
SFTRES — Soft Reset
When this bit is set by the CPU, the MSCAN08 immediately enters the soft reset
state. Any ongoing transmission or reception is aborted and synchronization to
the bus is lost.
The following registers enter and stay in their hard reset state:
CMCR0, CRFLG, CRIER, CTFLG, and CTCR.
The registers CMCR1, CBTR0, CBTR1, CIDAC, CIDAR0–CIDAR3, and
CIDMR0–CIDMR3 can only be written by the CPU when the MSCAN08 is in soft
reset state. The values of the error counters are not affected by soft reset.
When this bit is cleared by the CPU, the MSCAN08 tries to synchronize to the
CAN bus. If the MSCAN08 is not in bus-off state, it will be synchronized after 11
recessive bits on the bus; if the MSCAN08 is in bus-off state, it continues to wait
for 128 occurrences of 11 recessive bits.
Clearing SFTRES and writing to other bits in CMCR0 must be in separate
instructions.
1 = MSCAN08 in soft reset state
0 = Normal operation
Data Sheet
170
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
12.13.2 MSCAN08 Module Control Register 1
Address:
$0501
Bit 7
0
6
0
5
0
4
0
3
0
2
LOOPB
0
1
WUPM
0
Bit 0
CLKSRC
0
Read:
Write:
Reset:
0
0
0
0
0
= Unimplemented
Figure 12-17. Module Control Register (CMCR1)
LOOPB — Loop Back Self-Test Mode
When this bit is set, the MSCAN08 performs an internal loop back which can be
used for self-test operation: the bit stream output of the transmitter is fed back
to the receiver internally. The CANRX input pin is ignored and the CANTX output
goes to the recessive state (1). The MSCAN08 behaves as it does normally
when transmitting and treats its own transmitted message as a message
received from a remote node. In this state the MSCAN08 ignores the bit sent
during the ACK slot of the CAN frame Acknowledge field to insure proper
reception of its own message. Both transmit and receive interrupts are
generated.
1 = Activate loop back self-test mode
0 = Normal operation
WUPM — Wakeup Mode
This flag defines whether the integrated low-pass filter is applied to protect the
MSCAN08 from spurious wakeups (see 12.8.5 Programmable Wakeup
Function).
1 = MSCAN08 will wakeup the CPU only in cases of a dominant pulse on the
bus which has a length of at least twup
.
0 = MSCAN08 will wakeup the CPU after any recessive-to-dominant edge on
the CAN bus.
CLKSRC — Clock Source
This flag defines which clock source the MSCAN08 module is driven from (see
12.10 Clock System).
1 = The MSCAN08 clock source is CGMOUT (see Figure 12-8).
0 = The MSCAN08 clock source is CGMXCLK/2 (see Figure 12-8).
NOTE:
The CMCR1 register can be written only if the SFTRES bit in the MSCAN08
module control register is set
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
171
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
12.13.3 MSCAN08 Bus Timing Register 0
Address:
$0502
Bit 7
6
SJW0
0
5
BRP5
0
4
BRP4
0
3
BRP3
0
2
BRP2
0
1
BRP1
0
Bit 0
BRP0
0
Read:
Write:
Reset:
SJW1
0
Figure 12-18. Bus Timing Register 0 (CBTR0)
SJW1 and SJW0 — Synchronization Jump Width
The synchronization jump width (SJW) defines the maximum number of time
quanta (Tq) clock cycles by which a bit may be shortened, or lengthened, to
achieve resynchronization on data transitions on the bus (see Table 12-6).
Table 12-6. Synchronization Jump Width
Synchronization
Jump Width
SJW1
SJW0
1 Tq cycle
0
0
1
1
0
1
0
1
2 Tq cycle
3 Tq cycle
4 Tq cycle
BRP5–BRP0 — Baud Rate Prescaler
These bits determine the time quanta (Tq) clock, which is used to build up the
individual bit timing, according to Table 12-7.
Table 12-7. Baud Rate Prescaler
Prescaler
Value (P)
BRP5
BRP4
BRP3
BRP2
BRP1
BRP0
0
0
0
0
:
0
0
0
0
:
0
0
0
0
:
0
0
0
0
:
0
0
1
1
:
0
1
0
1
:
1
2
3
4
:
:
:
:
:
:
:
:
1
1
1
1
1
1
64
NOTE:
The CBTR0 register can be written only if the SFTRES bit in the MSCAN08 module
control register is set.
Data Sheet
172
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
12.13.4 MSCAN08 Bus Timing Register 1
Address:
$0503
Bit 7
6
TSEG22
0
5
TSEG21
0
4
TSEG20
0
3
TSEG13
0
2
TSEG12
0
1
TSEG11
0
Bit 0
TSEG10
0
Read:
Write:
Reset:
SAMP
0
Figure 12-19. Bus Timing Register 1 (CBTR1)
SAMP — Sampling
This bit determines the number of serial bus samples to be taken per bit time. If
set, three samples per bit are taken, the regular one (sample point) and two
preceding samples, using a majority rule. For higher bit rates, SAMP should be
cleared, which means that only one sample will be taken per bit.
1 = Three samples per bit(1)
0 = One sample per bit
TSEG22–TSEG10 — Time Segment
Time segments within the bit time fix the number of clock cycles per bit time and
the location of the sample point. Time segment 1 (TSEG1) and time segment 2
(TSEG2) are programmable as shown in Table 12-8.
The bit time is determined by the oscillator frequency, the baud rate prescaler,
and the number of time quanta (Tq) clock cycles per bit as shown in Table 12-4).
Pres value
Bit time =
• number of time quanta
fMSCANCLK
NOTE:
The CBTR1 register can only be written if the SFTRES bit in the MSCAN08 module
control register is set.
Table 12-8. Time Segment Values
Time
Segment 1
Time
Segment 2
TSEG13 TSEG12 TSEG11 TSEG10
TSEG22 TSEG21 TSEG20
1 Tq Cycle(1)
2 Tq Cycles(1)
1 Tq Cycle(1)
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
0
0
1
2 Tq Cycles
3Tq Cycles(1)
4 Tq Cycles
.
.
.
.
.
.
.
0
.
0
.
1
.
1
.
.
8Tq Cycles
.
1
1
1
.
.
.
.
.
16 Tq Cycles
1
1
1
1
1. This setting is not valid. Please refer to Table 12-4 for valid settings.
1. In this case PHASE_SEG1 must be at least 2 time quanta.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA MSCAN08 Controller (MSCAN08)
Data Sheet
173
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
12.13.5 MSCAN08 Receiver Flag Register (CRFLG)
All bits of this register are read and clear only. A flag can be cleared by writing a 1
to the corresponding bit position. A flag can be cleared only when the condition
which caused the setting is valid no more. Writing a 0 has no effect on the flag
setting. Every flag has an associated interrupt enable flag in the CRIER register. A
hard or soft reset will clear the register.
Address:
$0504
Bit 7
6
RWRNIF
0
5
TWRNIF
0
4
RERRIF
0
3
TERRIF
0
2
BOFFIF
0
1
OVRIF
0
Bit 0
RXF
0
Read:
Write:
Reset:
WUPIF
0
Figure 12-20. Receiver Flag Register (CRFLG)
WUPIF — Wakeup Interrupt Flag
If the MSCAN08 detects bus activity while in sleep mode, it sets the WUPIF flag.
If not masked, a wakeup interrupt is pending while this flag is set.
1 = MSCAN08 has detected activity on the bus and requested wakeup.
0 = No wakeup interrupt has occurred.
RWRNIF — Receiver Warning Interrupt Flag
This flag is set when the MSCAN08 goes into warning status due to the receive
error counter (REC) exceeding 96 and neither one of the error interrupt flags or
the bus-off interrupt flag is set(1). If not masked, an error interrupt is pending
while this flag is set.
1 = MSCAN08 has gone into receiver warning status.
0 = No receiver warning status has been reached.
TWRNIF — Transmitter Warning Interrupt Flag
This flag is set when the MSCAN08 goes into warning status due to the transmit
error counter (TEC) exceeding 96 and neither one of the error interrupt flags or
the bus-off interrupt flag is set(2). If not masked, an error interrupt is pending
while this flag is set.
1 = MSCAN08 has gone into transmitter warning status.
0 = No transmitter warning status has been reached.
RERRIF — Receiver Error Passive Interrupt Flag
This flag is set when the MSCAN08 goes into error passive status due to the
receive error counter exceeding 127 and the bus-off interrupt flag is not set(3).
If not masked, an error interrupt is pending while this flag is set.
1 = MSCAN08 has gone into receiver error passive status.
0 = No receiver error passive status has been reached.
1. Condition to set the flag: RWRNIF = (96 → REC) & RERRIF & TERRIF & BOFFIF
2. Condition to set the flag: TWRNIF = (96 → TEC) & RERRIF & TERRIF & BOFFIF
3. Condition to set the flag: RERRIF = (127 → REC → 255) & BOFFIF
Data Sheet
174
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
TERRIF — Transmitter Error Passive Interrupt Flag
This flag is set when the MSCAN08 goes into error passive status due to the
transmit error counter exceeding 127 and the bus-off interrupt flag is not set(1).
If not masked, an error interrupt is pending while this flag is set.
1 = MSCAN08 went into transmit error passive status.
0 = No transmit error passive status has been reached.
BOFFIF — Bus-Off Interrupt Flag
This flag is set when the MSCAN08 goes into bus-off status, due to the transmit
error counter exceeding 255. It cannot be cleared before the MSCAN08 has
monitored 128 times 11 consecutive ‘recessive’ bits on the bus. If not masked,
an error interrupt is pending while this flag is set.
1 = MSCAN08has gone into bus-off status.
0 = No bus-off status has been reached.
OVRIF — Overrun Interrupt Flag
This flag is set when a data overrun condition occurs. If not masked, an error
interrupt is pending while this flag is set.
1 = A data overrun has been detected since last clearing the flag.
0 = No data overrun has occurred.
RXF — Receive Buffer Full
The RXF flag is set by the MSCAN08 when a new message is available in the
foreground receive buffer. This flag indicates whether the buffer is loaded with
a correctly received message. After the CPU has read that message from the
receive buffer the RXF flag must be cleared to release the buffer. A set RXF flag
prohibits the exchange of the background receive buffer into the foreground
buffer. If not masked, a receive interrupt is pending while this flag is set.
1 = The receive buffer is full. A new message is available.
0 = The receive buffer is released (not full).
NOTE:
To ensure data integrity, no registers of the receive buffer shall be read while the
RXF flag is cleared.
The CRFLG register is held in the reset state when the SFTRES bit in CMCR0 is
set.
1. Condition to set the flag: TERRIF = (128 → TEC → 255) & BOFFIF
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
175
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
12.13.6 MSCAN08 Receiver Interrupt Enable Register
Address:
$0505
Bit 7
6
RWRNIE
0
5
TWRNIE
0
4
RERRIE
0
3
TERRIE
0
2
BOFFIE
0
1
OVRIE
0
Bit 0
RXFIE
0
Read:
Write:
Reset:
WUPIE
0
Figure 12-21. Receiver Interrupt Enable Register (CRIER)
WUPIE — Wakeup Interrupt Enable
1 = A wakeup event will result in a wakeup interrupt.
0 = No interrupt will be generated from this event.
RWRNIE — Receiver Warning Interrupt Enable
1 = A receiver warning status event will result in an error interrupt.
0 = No interrupt is generated from this event.
TWRNIE — Transmitter Warning Interrupt Enable
1 = A transmitter warning status event will result in an error interrupt.
0 = No interrupt is generated from this event.
RERRIE — Receiver Error Passive Interrupt Enable
1 = A receiver error passive status event will result in an error interrupt.
0 = No interrupt is generated from this event.
TERRIE — Transmitter Error Passive Interrupt Enable
1 = A transmitter error passive status event will result in an error interrupt.
0 = No interrupt is generated from this event.
BOFFIE — Bus-Off Interrupt Enable
1 = A bus-off event will result in an error interrupt.
0 = No interrupt is generated from this event.
OVRIE — Overrun Interrupt Enable
1 = An overrun event will result in an error interrupt.
0 = No interrupt is generated from this event.
RXFIE — Receiver Full Interrupt Enable
1 = A receive buffer full (successful message reception) event will result in a
receive interrupt.
0 = No interrupt will be generated from this event.
NOTE:
The CRIER register is held in the reset state when the SFTRES bit in CMCR0 is
set.
Data Sheet
176
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
12.13.7 MSCAN08 Transmitter Flag Register
The abort acknowledge flags are read only. The transmitter buffer empty flags are
read and clear only. A flag can be cleared by writing a 1 to the corresponding bit
position. Writing a 0 has no effect on the flag setting. The transmitter buffer empty
flags each have an associated interrupt enable bit in the CTCR register. A hard or
soft reset will resets the register.
Address:
$0506
Bit 7
0
5
6
5
4
3
0
2
TXE2
1
1
TXE1
1
Bit 0
TXE0
1
Read:
Write:
Reset:
ABTAK2
ABTAK1
ABTAK0
0
0
0
0
0
= Unimplemented
Figure 12-22. Transmitter Flag Register (CTFLG)
ABTAK2–ABTAK0 — Abort Acknowledge
This flag acknowledges that a message has been aborted due to a pending
abort request from the CPU. After a particular message buffer has been flagged
empty, this flag can be used by the application software to identify whether the
message has been aborted successfully or has been sent. The ABTAKx flag is
cleared implicitly whenever the corresponding TXE flag is cleared.
1 = The message has been aborted.
0 = The message has not been aborted, thus has been sent out.
TXE2–TXE0 — Transmitter Empty
This flag indicates that the associated transmit message buffer is empty, thus
not scheduled for transmission. The CPU must handshake (clear) the flag after
a message has been set up in the transmit buffer and is due for transmission.
The MSCAN08 sets the flag after the message has been sent successfully. The
flag is also set by the MSCAN08 when the transmission request was
successfully aborted due to a pending abort request (see 12.12.5 Transmit
Buffer Priority Registers). If not masked, a receive interrupt is pending while
this flag is set.
Clearing a TXEx flag also clears the corresponding ABTAKx flag (ABTAK, see
above). When a TXEx flag is set, the corresponding ABTRQx bit (ABTRQ) is
cleared. See 12.13.8 MSCAN08 Transmitter Control Register
1 = The associated message buffer is empty (not scheduled).
0 = The associated message buffer is full (loaded with a message due for
transmission).
NOTE:
To ensure data integrity, no registers of the transmit buffers should be written to
while the associated TXE flag is cleared.
The CTFLG register is held in the reset state when the SFTRES bit in CMCR0 is
set.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
177
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
12.13.8 MSCAN08 Transmitter Control Register
Address:
$0507
Bit 7
0
6
ABTRQ2
0
5
ABTRQ1
0
4
ABTRQ0
0
3
0
2
TXEIE2
0
1
TXEIE1
0
Bit 0
TXEIE0
0
Read:
Write:
Reset:
0
0
= Unimplemented
Figure 12-23. Transmitter Control Register (CTCR)
ABTRQ2–ABTRQ0 — Abort Request
The CPU sets an ABTRQx bit to request that an already scheduled message
buffer (TXE = 0) be aborted. The MSCAN08 will grant the request if the
message has not already started transmission, or if the transmission is not
successful (lost arbitration or error). When a message is aborted the associated
TXE and the abort acknowledge flag (ABTAK) (see 12.13.7 MSCAN08
Transmitter Flag Register) will be set and an TXE interrupt is generated if
enabled. The CPU cannot reset ABTRQx. ABTRQx is cleared implicitly
whenever the associated TXE flag is set.
1 = Abort request pending
0 = No abort request
NOTE:
NOTE:
The software must not clear one or more of the TXE flags in CTFLG and
simultaneously set the respective ABTRQ bit(s).
TXEIE2–TXEIE0 — Transmitter Empty Interrupt Enable
1 = A transmitter empty (transmit buffer available for transmission) event
results in a transmitter empty interrupt.
0 = No interrupt is generated from this event.
The CTCR register is held in the reset state when the SFTRES bit in CMCR0 is set.
Data Sheet
178
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
12.13.9 MSCAN08 Identifier Acceptance Control Register
Address:
$0508
Bit 7
0
6
IDAM2
0
5
IDAM1
0
4
IDAM0
0
3
0
2
1
Bit 0
Read:
Write:
Reset:
IDHIT2
IDHIT1
IDHIT0
0
0
0
0
0
= Unimplemented
Figure 12-24. Identifier Acceptance Control Register (CIDAC)
IDAM2–IDAM0— Identifier Acceptance Mode
The CPU sets these flags to define the identifier acceptance filter organization
(see 12.5 Identifier Acceptance Filter). Table 12-9 summarizes the different
settings. In “filter closed” mode no messages will be accepted so that the
foreground buffer will never be reloaded.
Table 12-9. Identifier Acceptance Mode Settings
IDAM2
IDAM1
IDAM0
Identifier Acceptance Mode
Single 32-bit acceptance filter
Two 16-bit acceptance filter
Four 8-bit acceptance filters
Filter closed
0
0
0
0
1
0
0
1
1
X
0
1
0
1
X
Reserved
IDHIT2–IDHIT0— Identifier Acceptance Hit Indicator
The MSCAN08 sets these flags to indicate an identifier acceptance hit (see 12.5
Identifier Acceptance Filter). Table 12-9 summarizes the different settings.
Table 12-10. Identifier Acceptance Hit Indication
IDHIT2
IDHIT1
IDHIT0
Identifier Acceptance Hit
Filter 0 hit
0
0
0
0
1
0
0
1
1
X
0
1
0
1
X
Filter 1 hit
Filter 2 hit
Filter 3 hit
Reserved
The IDHIT indicators are always related to the message in the foreground buffer.
When a message gets copied from the background to the foreground buffer, the
indicators are updated as well.
NOTE:
The CIDAC register can be written only if the SFTRES bit in the CMCR0 is set.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
179
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
12.13.10 MSCAN08 Receive Error Counter
Address:
$050E
Bit 7
6
5
4
3
2
1
Bit 0
Read: RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0
Write:
Reset:
0
0
0
0
0
0
0
0
= Unimplemented
Figure 12-25. Receiver Error Counter (CRXERR)
This read-only register reflects the status of the MSCAN08 receive error counter.
12.13.11 MSCAN08 Transmit Error Counter
Address:
$050F
Bit 7
6
5
4
3
2
1
Bit 0
Read: TXERR7
Write:
TXERR6
TXERR5
TXERR4
TXERR3
TXERR2
TXERR1
TXERR0
Reset:
0
0
0
0
0
0
0
0
= Unimplemented
Figure 12-26. Transmit Error Counter (CTXERR)
This read-only register reflects the status of the MSCAN08 transmit error counter.
NOTE:
Both error counters may only be read when in sleep or soft reset mode.
Data Sheet
180
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
12.13.12 MSCAN08 Identifier Acceptance Registers
On reception each message is written into the background receive buffer. The CPU
is only signalled to read the message, however, if it passes the criteria in the
identifier acceptance and identifier mask registers (accepted); otherwise, the
message will be overwritten by the next message (dropped).
The acceptance registers of the MSCAN08 are applied on the IDR0 to IDR3
registers of incoming messages in a bit by bit manner.
For extended identifiers, all four acceptance and mask registers are applied. For
standard identifiers only the first two (CIDMR0/CIDMR1 and CIDAR0/CIDAR1) are
applied.
CIDAR0 Address: $0510
Bit 7
6
5
4
3
2
1
Bit 0
AC0
Read:
Write:
Reset:
AC7
AC6
AC5
AC4
AC3
AC2
AC1
Unaffected by reset
CIDAR1 Address: $050511
Bit 7
6
5
4
3
2
1
Bit 0
AC0
Read:
AC7
AC6
AC5
AC4
AC3
AC2
AC1
Write:
Reset:
Unaffected by reset
CIDAR2 Address: $0512
Bit 7
6
5
4
3
2
1
Bit 0
AC0
Read:
AC7
Write:
AC6
AC5
AC4
AC3
AC2
AC1
Reset:
Unaffected by reset
CIDAR3 Address: $0513
Bit 7
6
5
4
3
2
1
Bit 0
AC0
Read:
AC7
Write:
AC6
AC5
AC4
AC3
AC2
AC1
Reset:
Unaffected by reset
Figure 12-27. Identifier Acceptance Registers
(CIDAR0–CIDAR3)
AC7–AC0 — Acceptance Code Bits
AC7–AC0 comprise a user-defined sequence of bits with which the
corresponding bits of the related identifier register (IDRn) of the receive
message buffer are compared. The result of this comparison is then masked
with the corresponding identifier mask register.
NOTE:
The CIDAR0–CIDAR3 registers can be written only if the SFTRES bit in CMCR0 is
set
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
181
MOTOROLA
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
12.13.13 MSCAN08 Identifier Mask Registers (CIDMR0–CIDMR3)
The identifier mask registers specify which of the corresponding bits in the identifier
acceptance register are relevant for acceptance filtering. For standard identifiers it
is required to program the last three bits (AM2–AM0) in the mask register CIDMR1
to ‘don’t care’.
CIDMRO Address: $0514
Bit 7
6
5
4
3
2
1
Bit 0
AM0
Read:
Write:
Reset:
AM7
AM6
AM5
AM4
AM3
AM2
AM1
Unaffected by reset
CIDMR1 Address: $0515
Bit 7
6
5
4
3
2
1
Bit 0
AM0
Read:
AM7
Write:
AM6
AM5
AM4
AM3
AM2
AM1
Reset:
Unaffected by reset
CIDMR2 Address: $0516
Bit 7
6
5
4
3
2
1
Bit 0
AM0
Read:
AM7
Write:
AM6
AM5
AM4
AM3
AM2
AM1
Reset:
Unaffected by reset
CIDMR3 Address: $0517
Bit 7
6
5
4
3
2
1
Bit 0
AM0
Read:
AM7
Write:
AM6
AM5
AM4
AM3
AM2
AM1
Reset:
Unaffected by reset
Figure 12-28. Identifier Mask Registers
(CIDMR0–CIDMR3)
AM7–AM0 — Acceptance Mask Bits
If a particular bit in this register is cleared, this indicates that the corresponding
bit in the identifier acceptance register must be the same as its identifier bit
before a match will be detected. The message will be accepted if all such bits
match. If a bit is set, it indicates that the state of the corresponding bit in the
identifier acceptance register will not affect whether or not the message is
accepted.
1 = Ignore corresponding acceptance code register bit.
0 = Match corresponding acceptance code register and identifier bits.
NOTE:
The CIDMR0–CIDMR3 registers can be written only if the SFTRES bit in the
CMCR0 is set
Data Sheet
182
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MSCAN08 Controller (MSCAN08)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 13. Input/Output (I/O) Ports
13.1 Introduction
Bidirectional input-output (I/O) pins form seven parallel ports. All I/O pins are
programmable as inputs or outputs. All individual bits within port A, port C, port D
and port F are software configurable with pullup devices if configured as input port
bits. The pullup devices are automatically and dynamically disabled when a port bit
is switched to output mode.
NOTE:
Connect any unused I/O pins to an appropriate logic level, either VDD or VSS.
Although the I/O ports do not require termination for proper operation, termination
reduces excess current consumption and the possibility of electrostatic damage.
Not all port pins are bonded out in all packages. Care sure be taken to make any
unbonded port pins an output to prevent them from being floating inputs.
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Port A Data Register
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
$0000
(PTA) Write:
See page 187.
Reset:
Read:
Unaffected by reset
PTB4 PTB3
Unaffected by reset
PTC4 PTC3
Unaffected by reset
PTD4 PTD3
Unaffected by reset
Port B Data Register
PTB7
1
PTB6
PTC6
PTD6
PTB5
PTC5
PTD5
PTB2
PTC2
PTD2
PTB1
PTC1
PTD1
PTB0
PTC0
PTD0
$0001
$0002
$0003
$0004
$0005
(PTB) Write:
See page 190.
Reset:
Read:
Port C Data Register
(PTC) Write:
See page 192.
Reset:
Read:
Port D Data Register
PTD7
(PTD) Write:
See page 194.
Reset:
Read:
Data Direction Register A
DDRA7
DDRA6
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
(DDRA) Write:
See page 188.
Reset:
Read:
0
DDRB7
0
0
DDRB6
0
0
DDRB5
0
0
DDRB4
0
0
DDRB3
0
0
DDRB2
0
0
DDRB1
0
0
DDRB0
0
Data Direction Register B
(DDRB) Write:
See page 190.
Reset:
= Unimplemented
Figure 13-1. I/O Port Register Summary (Sheet 1 of 2)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
183
MOTOROLA
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Addr.
Register Name
Bit 7
6
5
DDRC5
0
4
DDRC4
0
3
DDRC3
0
2
DDRC2
0
1
DDRC1
0
Bit 0
DDRC0
0
Read:
0
Data Direction Register C
DDRC6
0
$0006
(DDRC) Write:
See page 192.
Reset:
Read:
0
Data Direction Register D
DDRD7
DDRD6
DDRD5
0
DDRD4
0
DDRD3
0
DDRD2
0
DDRD1
0
DDRD0
0
$0007
$0008
$000C
$000D
$000E
$000F
(DDRD) Write:
See page 196.
Reset:
Read:
0
0
0
0
Port E Data Register
PTE5
PTE4
PTE3
PTE2
PTE1
PTE0
(PTE) Write:
See page 198.
Reset:
Read:
Unaffected by reset
0
0
0
0
Data Direction Register E
DDRE5
0
DDRE4
0
DDRE3
0
DDRE2
0
DDRE1
0
DDRE0
0
(DDRE) Write:
See page 199.
Reset:
Read:
Port A Input Pullup Enable
PTAPUE7 PTAPUE6 PTAPUE5 PTAPUE4 PTAPUE3 PTAPUE2 PTAPUE1 PTAPUE0
Register (PTAPUE) Write:
See page 189.
Reset:
0
0
0
0
0
0
0
0
0
Read:
Port C Input Pullup Enable
PTCPUE6 PTCPUE5 PTCPUE4 PTCPUE3 PTCPUE2 PTCPUE1 PTCPUE0
Register (PTCPUE) Write:
See page 194.
Reset:
0
0
0
0
0
0
0
0
Read:
Port D Input Pullup Enable
PTDPUE7 PTDPUE6 PTDPUE5 PTDPUE4 PTDPUE3 PTDPUE2 PTDPUE1 PTDPUE0
Register (PTDPUE) Write:
See page 197.
Reset:
0
0
0
0
0
0
0
0
Port F Data Register Read:
(PTF)
PTF7
PTF6
PTF5
PTF4
PTAF3
PTF2
PTF1
PTF0
Write:
$0440
$0441
$0444
$0445
See page 200.
Reset:
Unaffected by reset
PTG4 PTG3
Unaffected by reset
Port G Data Register Read:
(PTG)
PTG7
PTG6
PTG5
PTG2
PTG1
PTG0
Write:
See page 202.
Reset:
Data Direction Register F Read:
(DDRF)
DDRF7
DDRF6
DDRF5
DDRF4
DDRF3
DDRF2
DDRF1
DDRF0
Write:
See page 200.
Reset:
0
DDRG7
0
0
DDRG6
0
0
DDRG5
0
0
DDRG4
0
0
DDRG3
0
0
DDRG2
0
0
DDRG1
0
0
DDRG0
0
Data Direction Register G Read:
(DDRG)
Write:
See page 202.
Reset:
= Unimplemented
Figure 13-1. I/O Port Register Summary (Sheet 2 of 2)
Data Sheet
184
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Introduction
Table 13-1. Port Control Register Bits Summary
Port Bit
DDR
Module Control
KBIE0
Module Control
Pin
0
1
2
DDRA0
DDRA1
DDRA2
DDRA3
DDRA4
DDRA5
DDRA6
DDRA7
DDRB0
DDRB1
DDRB2
DDRB3
DDRB4
DDRB5
DDRB6
DDRB7
DDRC0
DDRC1
DDRC2
DDRC3
DDRC4
DDRC5
DDRC6
DDRD0
DDRD1
DDRD2
DDRD3
DDRD4
DDRD5
DDRD6
DDRD7
PTA0/KBD0/AD8
PTA1/KBD1/AD9
PTA2/KBD2/AD10
PTA3/KBD3/AD11
PTA4/KBD4/AD12
PTA5/KBD5/AD13
PTA6/KBD6/AD14
PTA7/KBD7/AD15
PTB0/AD0
KBIE1
KBIE2
3
KBIE3
A
KBD
ADC[15:8]
ADCH4–ADCH0
4
KBIE4
5
6
7
0
1
2
KBIE5
KBIE6
KBIE7
PTB1/AD1
PTB2/AD2
3
PTB3/AD3
B
ADC
ADCH4–ADCH0
—
—
—
—
—
—
4
PTB4/AD4
5
6
7
0
1
2
PTB5/AD5
PTB6/AD6
PTB7/AD7
PTC0
MSCAN
CANEN
PTC1
PTC2
C
3
4
5
6
0
1
2
3
4
5
6
7
PTC3
PTC4
PTC5
PTC6
PTD0/SS/MCLK
PTD1/MISO
PTD2/MOSI
PTD3/SPSCK
PTD4/T1CH0
PTD5/T1CH1
PTD6/T2CH0
PTD7/T2CH1
SPI
SPE
D
ELS0B:ELS0A
ELS1B:ELS1A
ELS0B:ELS0A
ELS1B:ELS1A
TIM1
TIM2
— Continued o n next page
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Input/Output (I/O) Ports
Data Sheet
185
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Table 13-1. Port Control Register Bits Summary (Continued)
Port Bit
DDR
Module Control
Module Control
Pin
0
1
DDRE0
DDRE1
DDRE2
DDRE3
DDRE4
DDRE5
DDRF0
DDRF1
DDRF2
DDRF3
DDRF4
DDRF5
DDRF6
DDRF7
DDRG0
DDRG1
DDRG2
DDRG3
DDRG4
DDRG5
DDRG6
DDRG7
PTE0/TxD
PTE1/RxD
PTE2
SCI
ENSCI
2
E
—
—
3
PTE3
4
5
0
1
2
PTE4
PTE5
PTF0
PTF1
PTF2
3
PTF3
F
—
—
4
ELS2B:ELS2A
PTF4/T2CH2
PTF5/T2CH3
PTF6/T2CH4
PTF7/T2CH5
PTG0/AD16
PTG1/AD17
PTG2/AD18
PTG3/AD19
PTG4/AD20
PTG5/AD21
PTG6/AD22
PTG7/AD23
5
6
7
0
1
2
ELS3B:ELS3A
ELS4B:ELS4A
ELS5B:ELS5A
TIM2
3
G
4
ADC
ADCH[23:16]
—
—
5
6
7
Data Sheet
186
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port A
13.2 Port A
Port A is an 8-bit special-function port that shares all eight of its pins with the
keyboard interrupt (KBI) module and the ADC module. Port A also has software
configurable pullup devices if configured as an input port.
13.2.1 Port A Data Register
The port A data register (PTA) contains a data latch for each of the eight port A
pins.
Address:
$0000
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
Reset:
Unaffected by reset
Alternate Function:
Alternate Function:
KBD7
AD15
KBD6
AD14
KBD5
AD13
KBD4
AD12
KBD3
AD11
KBD2
AD10
KBD1
AD9
KBD0
AD8
Figure 13-2. Port A Data Register (PTA)
PTA7–PTA0 — Port A Data Bits
These read/write bits are software programmable. Data direction of each port A
pin is under the control of the corresponding bit in data direction register A.
Reset has no effect on port A data.
KBD7–KBD0 — Keyboard Inputs
The keyboard interrupt enable bits, KBIE7–KBIE0, in the keyboard interrupt
control register (KBICR) enable the port A pins as external interrupt pins. See
Section 9. Keyboard Interrupt Module (KBI)
AD15–AD8 — Analog-to-Digital Input Bits
AD15–AD8 are pins used for the input channels to the analog-to-digital
converter module. The channel select bits in the ADC status and control register
define which port A pin will be used as an ADC input and overrides any control
from the port I/O logic by forcing that pin as the input to the analog circuitry.
NOTE:
Care must be taken when reading port A while applying analog voltages to
AD15–AD8 pins. If the appropriate ADC channel is not enabled, excessive current
drain may occur if analog voltages are applied to the PTAx/KBDx/ADx pin, while
PTA is read as a digital input during the CPU read cycle. Those ports not selected
as analog input channels are considered digital I/O ports.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
187
MOTOROLA
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
13.2.2 Data Direction Register A
Data direction register A (DDRA) determines whether each port A pin is an input or
an output. Writing a 1 to a DDRA bit enables the output buffer for the corresponding
port A pin; a 0 disables the output buffer.
Address:
$0004
Bit 7
6
DDRA6
0
5
DDRA5
0
4
DDRA4
0
3
DDRA3
0
2
DDRA2
0
1
DDRA1
0
Bit 0
DDRA0
0
Read:
Write:
Reset:
DDRA7
0
Figure 13-3. Data Direction Register A (DDRA)
DDRA7–DDRA0 — Data Direction Register A Bits
These read/write bits control port A data direction. Reset clears
DDRA7–DDRA0, configuring all port A pins as inputs.
1 = Corresponding port A pin configured as output
0 = Corresponding port A pin configured as input
NOTE:
Avoid glitches on port A pins by writing to the port A data register before changing
data direction register A bits from 0 to 1.
Figure 13-4 shows the port A I/O logic.
When bit DDRAx is a 1, reading address $0000 reads the PTAx data latch. When
bit DDRAx is a 0, reading address $0000 reads the voltage level on the pin. The
data latch can always be written, regardless of the state of its data direction bit.
Table 13-2 summarizes the operation of the port A pins.
VDD
PTAPUEx
READ DDRA ($0004)
INTERNAL
PULLUP
DEVICE
WRITE DDRA ($0004)
DDRAx
RESET
WRITE PTA ($0000)
PTAx
PTAx
READ PTA ($0000)
Figure 13-4. Port A I/O Circuit
Data Sheet
188
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port A
Table 13-2. Port A Pin Functions
Accesses
to DDRA
Accesses
to PTA
PTAPUE
Bit
DDRA
Bit
PTA
Bit
I/O Pin
Mode
Read/Write
Read
Write
(2)
X(1)
X
PTA7–PTA0(3)
1
0
DDRA7–DDRA0
Pin
Input, VDD
Input, Hi-Z(4)
Output
PTA7–PTA0(3)
PTA7–PTA0
0
0
1
DDRA7–DDRA0
DDRA7–DDRA0
Pin
X
X
PTA7–PTA0
1. X = Don’t care
2. I/O pin pulled up to VDD by internal pullup device
3. Writing affects data register, but does not affect input.
4. Hi-Z = High impedance
13.2.3 Port A Input Pullup Enable Register
The port A input pullup enable register (PTAPUE) contains a software configurable
pullup device for each of the eight port A pins. Each bit is individually configurable
and requires that the data direction register, DDRA, bit be configured as an input.
Each pullup is automatically and dynamically disabled when a port bit’s DDRA is
configured for output mode.
NOTE:
Pullup or pulldown resistors are automatically selected for keyboard interrupt pins
depending on the bit settings in the keyboard interrupt polarity register (INTKBIPR)
see 9.7.3 Keyboard Interrupt Polarity Register.
Address: $000D
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
PTAPUE7 PTAPUE6 PTAPUE5 PTAPUE4 PTAPUE3 PTAPUE2 PTAPUE1 PTAPUE0
0
0
0
0
0
0
0
0
Figure 13-5. Port A Input Pullup Enable Register (PTAPUE)
PTAPUE7–PTAPUE0 — Port A Input Pullup Enable Bits
These writable bits are software programmable to enable pullup devices on an
input port bit.
1 = Corresponding port A pin configured to have internal pullup
0 = Corresponding port A pin has internal pullup disconnected
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
189
MOTOROLA
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
13.3 Port B
Port B is an 8-bit special-function port that shares all eight of its pins with the
analog-to-digital converter (ADC) module.
13.3.1 Port B Data Register
The port B data register (PTB) contains a data latch for each of the eight port pins.
Address:
$0001
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
PTB7
PTB6
PTB5
PTB4
PTB3
PTB2
PTB1
PTB0
Reset:
Unaffected by reset
AD4 AD3
Alternate Function:
AD7
AD6
AD5
AD2
AD1
AD0
Figure 13-6. Port B Data Register (PTB)
PTB7–PTB0 — Port B Data Bits
These read/write bits are software-programmable. Data direction of each port B
pin is under the control of the corresponding bit in data direction register B.
Reset has no effect on port B data.
AD7–AD0 — Analog-to-Digital Input Bits
AD7–AD0 are pins used for the input channels to the analog-to-digital converter
module. The channel select bits in the ADC status and control register define
which port B pin will be used as an ADC input and overrides any control from
the port I/O logic by forcing that pin as the input to the analog circuitry.
NOTE:
Care must be taken when reading port B while applying analog voltages to
AD7–AD0 pins. If the appropriate ADC channel is not enabled, excessive current
drain may occur if analog voltages are applied to the PTBx/ADx pin, while PTB is
read as a digital input during the CPU read cycle. Those ports not selected as
analog input channels are considered digital I/O ports.
13.3.2 Data Direction Register B
Data direction register B (DDRB) determines whether each port B pin is an input or
an output. Writing a 1 to a DDRB bit enables the output buffer for the corresponding
port B pin; a 0 disables the output buffer.
Address:
$0005
Bit 7
6
DDRB6
0
5
DDRB5
0
4
DDRB4
0
3
DDRB3
0
2
DDRB2
0
1
DDRB1
0
Bit 0
DDRB0
0
Read:
Write:
Reset:
DDRB7
0
Figure 13-7. Data Direction Register B (DDRB)
Data Sheet
190
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port B
DDRB7–DDRB0 — Data Direction Register B Bits
These read/write bits control port B data direction. Reset clears
DDRB7–DDRB0, configuring all port B pins as inputs.
1 = Corresponding port B pin configured as output
0 = Corresponding port B pin configured as input
NOTE:
Avoid glitches on port B pins by writing to the port B data register before changing
data direction register B bits from 0 to 1.
Figure 13-8 shows the port B I/O logic.
When bit DDRBx is a 1, reading address $0001 reads the PTBx data latch. When
bit DDRBx is a 0, reading address $0001 reads the voltage level on the pin. The
data latch can always be written, regardless of the state of its data direction bit.
Table 13-3 summarizes the operation of the port B pins.
READ DDRB ($0005)
WRITE DDRB ($0005)
DDRBx
RESET
WRITE PTB ($0001)
PTBx
PTBx
READ PTB ($0001)
Figure 13-8. Port B I/O Circuit
Table 13-3. Port B Pin Functions
Accesses
to DDRB
Accesses
to PTB
DDRB
Bit
PTB
Bit
I/O Pin
Mode
Read/Write
Read
Pin
Write
X(1)
X
Input, Hi-Z(2)
Output
PTB7–PTB0(3)
PTB7–PTB0
0
1
DDRB7–DDRB0
DDRB7–DDRB0
PTB7–PTB0
1. X = Don’t care
2. Hi-Z = High impedance
3. Writing affects data register, but does not affect input.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
191
MOTOROLA
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
13.4 Port C
Port C is a 7-bit, general-purpose bidirectional I/O port. Port C also has software
configurable pullup devices if configured as an input port. PTC[1:0] are shared with
the MSCAN module.
13.4.1 Port C Data Register
The port C data register (PTC) contains a data latch for each of the seven port C
pins.
NOTE:
Bit 6 through bit 2 of PTC are not available in the 32-pin LQFP package.
Address:
$0002
Bit 7
1
6
5
4
3
2
1
Bit 0
Read:
Write:
PTC6
PTC5
PTC4
PTC3
PTC2
PTC1
PTC0
Reset:
Unaffected by reset
Alternate Function:
CANRX
CANTX
= Unimplemented
Figure 13-9. Port C Data Register (PTC)
PTC6–PTC0 — Port C Data Bits
These read/write bits are software-programmable. Data direction of each port C
pin is under the control of the corresponding bit in data direction register C.
Reset has no effect on port C data.
CANRX and CANTX — MSCAN08 Bits
The CANRX–CANTX pins are the MSCAN08 modules receive and transmit pins.
The CANEN bit in the MSCAN08 control register determines, whether the
PTC1/CANRX–PTC0/CANTX pins are MSCAN08 pins or general-purpose I/O
pins. See Section 12. MSCAN08 Controller (MSCAN08).
13.4.2 Data Direction Register C
Data direction register C (DDRC) determines whether each port C pin is an input
or an output. Writing a 1 to a DDRC bit enables the output buffer for the
corresponding port C pin; a 0 disables the output buffer.
Address:
$0006
Bit 7
0
6
DDRC6
0
5
DDRC5
0
4
DDRC4
0
3
DDRC3
0
2
DDRC2
0
1
DDRC1
0
Bit 0
DDRC0
0
Read:
Write:
Reset:
0
= Unimplemented
Figure 13-10. Data Direction Register C (DDRC)
Data Sheet
192
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port C
DDRC6–DDRC0 — Data Direction Register C Bits
These read/write bits control port C data direction. Reset clears
DDRC6–DDRC0, configuring all port C pins as inputs.
1 = Corresponding port C pin configured as output
0 = Corresponding port C pin configured as input
NOTE:
Avoid glitches on port C pins by writing to the port C data register before changing
data direction register C bits from 0 to 1.
Figure 13-11 shows the port C I/O logic.
When bit DDRCx is a 1, reading address $0002 reads the PTCx data latch. When
bit DDRCx is a 0, reading address $0002 reads the voltage level on the pin. The
data latch can always be written, regardless of the state of its data direction bit.
Table 13-4 summarizes the operation of the port C pins.
VDD
PTCPUEx
READ DDRC ($0006)
INTERNAL
PULLUP
DEVICE
WRITE DDRC ($0006)
DDRCx
RESET
WRITE PTC ($0002)
PTCx
PTCx
READ PTC ($0002)
Figure 13-11. Port C I/O Circuit
Table 13-4. Port C Pin Functions
Accesses
to DDRC
Accesses
to PTC
PTCPUE
Bit
DDRC
Bit
PTC
Bit
I/O Pin
Mode
Read/Write
Read
Write
(2)
X(1)
X
PTC6–PTC0(3)
1
0
DDRC6–DDRC0
Pin
Input, VDD
Input, Hi-Z(4)
Output
PTC6–PTC0(3)
PTC6–PTC0
0
0
1
DDRC6–DDRC0
DDRC6–DDRC0
Pin
X
X
PTC6–PTC0
1. X = Don’t care
2. I/O pin pulled up to VDD by internal pullup device.
3. Writing affects data register, but does not affect input.
4. Hi-Z = High impedance
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Input/Output (I/O) Ports
Data Sheet
193
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
13.4.3 Port C Input Pullup Enable Register
The port C input pullup enable register (PTCPUE) contains a software configurable
pullup device for each of the seven port C pins. Each bit is individually configurable
and requires that the data direction register, DDRC, bit be configured as an input.
Each pullup is automatically and dynamically disabled when a port bit’s DDRC is
configured for output mode.
Address:
$000E
Bit 7
0
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
PTCPUE6 PTCPUE5 PTCPUE4 PTCPUE3 PTCPUE2 PTCPUE1 PTCPUE0
0
0
0
0
0
0
0
0
= Unimplemented
Figure 13-12. Port C Input Pullup Enable Register (PTCPUE)
PTCPUE6–PTCPUE0 — Port C Input Pullup Enable Bits
These writable bits are software programmable to enable pullup devices on an
input port bit.
1 = Corresponding port C pin configured to have internal pullup
0 = Corresponding port C pin internal pullup disconnected
13.5 Port D
Port D is an 8-bit special-function port that shares four of its pins with the serial
peripheral interface (SPI) module and four of its pins with two timer interface (TIM1
and TIM2) modules. Port D also has software configurable pullup devices if
configured as an input port. PTD0 is shared with the MCLK output.
13.5.1 Port D Data Register
The port D data register (PTD) contains a data latch for each of the eight port D
pins.
Address:
$0003
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
PTD7
PTD6
PTD5
PTD4
PTD3
PTD2
PTD1
PTD0
Unaffected by reset
T1CH0 SPSCK
Alternate Function: T2CH1
T2CH0
T1CH1
MOSI
MISO
SS
MCLK
Figure 13-13. Port D Data Register (PTD)
Data Sheet
194
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port D
PTD7–PTD0 — Port D Data Bits
These read/write bits are software-programmable. Data direction of each port D
pin is under the control of the corresponding bit in data direction register D.
Reset has no effect on port D data.
T2CH1 and T2CH0 — Timer 2 Channel I/O Bits
The PTD5/T2CH1–PTD4/T2CH0 pins are the TIM2 input capture/output
compare pins. The edge/level select bits, ELSxB:ELSxA, determine whether the
PTD7/T2CH1–PTD6/T2CH0 pins are timer channel I/O pins or general-purpose
I/O pins. See Section 18. Timer Interface Module (TIM1) and Section 19.
Timer Interface Module (TIM2).
T1CH1 and T1CH0 — Timer 1 Channel I/O Bits
The PTD7/T1CH1–PTD6/T1CH0 pins are the TIM1 input capture/output
compare pins. The edge/level select bits, ELSxB and ELSxA, determine
whether the PTD7/T1CH1–PTD6/T1CH0 pins are timer channel I/O pins or
general-purpose I/O pins. See Section 18. Timer Interface Module (TIM1) and
Section 19. Timer Interface Module (TIM2).
SPSCK — SPI Serial Clock
The PTD3/SPSCK pin is the serial clock input of the SPI module. When the SPE
bit is clear, the PTD3/SPSCK pin is available for general-purpose I/O.
MOSI — Master Out/Slave In
The PTD2/MOSI pin is the master out/slave in terminal of the SPI module. When
the SPE bit is clear, the PTD2/MOSI pin is available for general-purpose I/O.
MISO — Master In/Slave Out
The PTD1/MISO pin is the master in/slave out terminal of the SPI module. When
the SPI enable bit, SPE, is clear, the SPI module is disabled, and the
PTD1/MISO pin is available for general-purpose I/O.
SS — Slave Select
The PTD0/SS pin is the slave select input of the SPI module. When the SPE bit
is clear, or when the SPI master bit, SPMSTR, is set, the PTD0/SS pin is
available for general-purpose I/O. When the SPI is enabled, the DDRD0 bit in
data direction register D (DDRD) has no effect on the PTD0/SS pin.
Data direction register D (DDRD) does not affect the data direction of port D pins
that are being used by the SPI module. However, the DDRD bits always determine
whether reading port D returns the states of the latches or the states of the pins.
See Table 13-5.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
195
MOTOROLA
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
13.5.2 Data Direction Register D
Data direction register D (DDRD) determines whether each port D pin is an input
or an output. Writing a 1 to a DDRD bit enables the output buffer for the
corresponding port D pin; a 0 disables the output buffer.
Address:
$0007
Bit 7
6
DDRD6
0
5
DDRD5
0
4
DDRD4
0
3
DDRD3
0
2
DDRD2
0
1
DDRD1
0
Bit 0
DDRD0
0
Read:
Write:
Reset:
DDRD7
0
Figure 13-14. Data Direction Register D (DDRD)
DDRD7–DDRD0 — Data Direction Register D Bits
These read/write bits control port D data direction. Reset clears
DDRD7–DDRD0, configuring all port D pins as inputs.
1 = Corresponding port D pin configured as output
0 = Corresponding port D pin configured as input
NOTE:
Avoid glitches on port D pins by writing to the port D data register before changing
data direction register D bits from 0 to 1.
Figure 13-15 shows the port D I/O logic.
When bit DDRDx is a 1, reading address $0003 reads the PTDx data latch. When
bit DDRDx is a 0, reading address $0003 reads the voltage level on the pin. The
data latch can always be written, regardless of the state of its data direction bit.
Table 13-5 summarizes the operation of the port D pins.
VDD
PTDPUEx
READ DDRD ($0007)
INTERNAL
PULLUP
DEVICE
WRITE DDRD ($0007)
DDRDx
RESET
WRITE PTD ($0003)
PTDx
PTDx
READ PTD ($0003)
Figure 13-15. Port D I/O Circuit
Data Sheet
196
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port D
Table 13-5. Port D Pin Functions
Accesses
to DDRD
Accesses
to PTD
PTDPUE
Bit
DDRD
Bit
PTD
Bit
I/O Pin
Mode
Read/Write
Read
Write
(2)
X(1)
X
PTD7–PTD0(3)
1
0
DDRD7–DDRD0
Pin
Input, VDD
Input, Hi-Z(4)
Output
PTD7–PTD0(3)
PTD7–PTD0
0
0
1
DDRD7–DDRD0
DDRD7–DDRD0
Pin
X
X
PTD7–PTD0
1. X = Don’t care
2. I/O pin pulled up to VDD by internal pullup device.
3. Writing affects data register, but does not affect input.
4. Hi-Z = High imp[edance
13.5.3 Port D Input Pullup Enable Register
The port D input pullup enable register (PTDPUE) contains a software configurable
pullup device for each of the eight port D pins. Each bit is individually configurable
and requires that the data direction register, DDRD, bit be configured as an input.
Each pullup is automatically and dynamically disabled when a port bit’s DDRD is
configured for output mode.
Address:
$000F
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
PTDPUE7 PTDPUE6 PTDPUE5 PTDPUE4 PTDPUE3 PTDPUE2 PTDPUE1 PTDPUE0
0
0
0
0
0
0
0
0
Figure 13-16. Port D Input Pullup Enable Register (PTDPUE)
PTDPUE7–PTDPUE0 — Port D Input Pullup Enable Bits
These writable bits are software programmable to enable pullup devices on an
input port bit.
1 = Corresponding port D pin configured to have internal pullup
0 = Corresponding port D pin has internal pullup disconnected
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
197
MOTOROLA
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
13.6 Port E
Port E is a 6-bit special-function port that shares two of its pins with the enhanced
serial communications interface (ESCI) module.
13.6.1 Port E Data Register
The port E data register contains a data latch for each of the six port E pins.
Address:
$0008
Bit 7
0
6
0
5
4
3
2
1
Bit 0
Read:
Write:
PTE5
PTE4
PTE3
PTE2
PTE1
PTE0
Reset:
Unaffected by reset
Alternate Function:
RxD
TxD
= Unimplemented
Figure 13-17. Port E Data Register (PTE)
PTE5–PTE0 — Port E Data Bits
These read/write bits are software-programmable. Data direction of each port E
pin is under the control of the corresponding bit in data direction register E.
Reset has no effect on port E data.
NOTE:
Data direction register E (DDRE) does not affect the data direction of port E pins
that are being used by the ESCI module. However, the DDRE bits always
determine whether reading port E returns the states of the latches or the states of
the pins. See Table 13-6.
RxD — SCI Receive Data Input
The PTE1/RxD pin is the receive data input for the ESCI module.
When the enable SCI bit, ENSCI, is clear, the ESCI module is disabled, and the
PTE1/RxD pin is available for general-purpose I/O. See Section 14. Enhanced
Serial Communications Interface (ESCI) Module.
TxD — SCI Transmit Data Output
The PTE0/TxD pin is the transmit data output for the ESCI module. When the
enable SCI bit, ENSCI, is clear, the ESCI module is disabled, and the PTE0/TxD
pin is available for general-purpose I/O. See Section 14. Enhanced Serial
Communications Interface (ESCI) Module.
13.6.2 Data Direction Register E
Data direction register E (DDRE) determines whether each port E pin is an input or
an output. Writing a 1 to a DDRE bit enables the output buffer for the corresponding
port E pin; a 0 disables the output buffer.
Data Sheet
198
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port E
Address:
$000C
Bit 7
0
6
0
5
DDRE5
0
4
DDRE4
0
3
DDRE3
0
2
DDRE2
0
1
DDRE1
0
Bit 0
DDRE0
0
Read:
Write:
Reset:
0
0
= Unimplemented
Figure 13-18. Data Direction Register E (DDRE)
DDRE5–DDRE0 — Data Direction Register E Bits
These read/write bits control port E data direction. Reset clears
DDRE5–DDRE0, configuring all port E pins as inputs.
1 = Corresponding port E pin configured as output
0 = Corresponding port E pin configured as input
NOTE:
Avoid glitches on port E pins by writing to the port E data register before changing
data direction register E bits from 0 to 1.
Figure 13-19 shows the port E I/O logic.
When bit DDREx is a 1, reading address $0008 reads the PTEx data latch. When
bit DDREx is a 0, reading address $0008 reads the voltage level on the pin. The
data latch can always be written, regardless of the state of its data direction bit.
Table 13-6 summarizes the operation of the port E pins.
READ DDRE ($000C)
WRITE DDRE ($000C)
DDREx
RESET
WRITE PTE ($0008)
PTEx
PTEx
READ PTE ($0008)
Figure 13-19. Port E I/O Circuit
Table 13-6. Port E Pin Functions
Accesses
to DDRE
Accesses
to PTE
DDRE
Bit
PTE
Bit
I/O Pin
Mode
Read/Write
Read
Pin
Write
X(1)
X
Input, Hi-Z(2)
Output
PTE5–PTE0(3)
PTE5–PTE0
0
1
DDRE5–DDRE0
DDRE5–DDRE0
PTE5–PTE0
1. X = Don’t care
2. Hi-Z = High impedance
3. Writing affects data register, but does not affect input.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
199
MOTOROLA
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
13.7 Port F
Port F is an 8-bit special-function port that shares four of its pins with the timer
interface (TIM2) module.
13.7.1 Port F Data Register
The port F data register (PTF) contains a data latch for each of the eight port F pins.
Address:
$0440
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
PTF7
PTF6
PTF5
PTF4
PTF3
PTF2
PTF1
PTF0
Unaffected by reset
T2CH2
Alternate Function: T2CH5
T2CH4
T2CH3
= Unimplemented
Figure 13-20. Port F Data Register (PTF)
PTF7–PTF0 — Port F Data Bits
These read/write bits are software-programmable. Data direction of each port F
pin is under the control of the corresponding bit in data direction register F.
Reset has no effect on port F data.
T2CH5–T2CH2 — Timer 2 Channel I/O Bits
The PTF7/T2CH5–PTF4/T2CH2 pins are the TIM2 input capture/output
compare pins. The edge/level select bits, ELSxB:ELSxA, determine whether the
PTF7/T2CH5–PTF4/T2CH2 pins are timer channel I/O pins or general-purpose
I/O pins. See Section 18. Timer Interface Module (TIM1) and Section 19.
Timer Interface Module (TIM2).
13.7.2 Data Direction Register F
Data direction register F (DDRF) determines whether each port F pin is an input or
an output. Writing a 1 to a DDRF bit enables the output buffer for the corresponding
port F pin; a 0 disables the output buffer.
Address:
$0444
Bit 7
6
DDRF6
0
5
DDRF5
0
4
DDRF4
0
3
DDRF3
0
2
DDRF2
0
1
DDRF1
0
Bit 0
DDRF0
0
Read:
Write:
Reset:
DDRF7
0
Figure 13-21. Data Direction Register F (DDRF)
Data Sheet
200
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port F
DDRF7–DDRF0 — Data Direction Register F Bits
These read/write bits control port F data direction. Reset clears
DDRF7–DDRF0, configuring all port F pins as inputs.
1 = Corresponding port F pin configured as output
0 = Corresponding port F pin configured as input
NOTE:
Avoid glitches on port F pins by writing to the port F data register before changing
data direction register F bits from 0 to 1.
Figure 13-22 shows the port F I/O logic.
READ DDRF ($0444)
WRITE DDRF ($0444)
DDRFx
RESET
WRITE PTF ($0440)
PTFx
PTFx
READ PTD ($0440)
Figure 13-22. Port F I/O Circuit
When bit DDRFx is a 1, reading address $0440 reads the PTFx data latch. When
bit DDRFx is a 0, reading address $0440 reads the voltage level on the pin. The
data latch can always be written, regardless of the state of its data direction bit.
Table 13-7 summarizes the operation of the port F pins.
Table 13-7. Port F Pin Functions
Accesses
to DDRF
Accesses
to PTF
DDRF
Bit
PTF
Bit
I/O Pin
Mode
Read/Write
Read
Pin
WritE
X(1)
X
Input, Hi-Z(2)
Output
PTF7–PTF0(3)
PTF7–PTF0
0
1
DDRF7–DDRF0
DDRF7–DDRF0
PTF7–PTF0
1. X = Don’t care
2. Hi-Z = High impedance
3. Writing affects data register, but does not affect input.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
201
MOTOROLA
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
13.8 Port G
Port G is an 8-bit special-function port that shares all eight of its pins with the
analog-to-digital converter (ADC) module.
13.8.1 Port G Data Register
The port G data register (PTG) contains a data latch for each of the eight port pins.
Address:
$0441
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
PTG7
PTG6
PTG5
PTG4
PTG3
PTG2
PTG1
PTG0
Reset:
Unaffected by reset
AD20 AD19
Alternate Function:
AD23
AD22
AD21
AD18
AD17
AD16
Figure 13-23. Port G Data Register (PTG)
PTG7–PTG0 — Port G Data Bits
These read/write bits are software-programmable. Data direction of each port G
pin is under the control of the corresponding bit in data direction register G.
Reset has no effect on port G data.
AD23–AD16 — Analog-to-Digital Input Bits
AD23–AD16 are pins used for the input channels to the analog-to-digital
converter module. The channel select bits in the ADC status and control register
define which port G pin will be used as an ADC input and overrides any control
from the port I/O logic by forcing that pin as the input to the analog circuitry.
NOTE:
Care must be taken when reading port G while applying analog voltages to
AD23–AD16 pins. If the appropriate ADC channel is not enabled, excessive current
drain may occur if analog voltages are applied to the PTGx/ADx pin, while PTG is
read as a digital input during the CPU read cycle. Those ports not selected as
analog input channels are considered digital I/O ports.
13.8.2 Data Direction Register G
Data direction register G (DDRG) determines whether each port G pin is an input
or an output. Writing a 1 to a DDRG bit enables the output buffer for the
corresponding port G pin; a 0 disables the output buffer.
Address:
$0445
Bit 7
6
DDRG6
0
5
DDRG5
0
4
DDRG4
0
3
DDRG3
0
2
DDRG2
0
1
DDRG1
0
Bit 0
DDRG0
0
Read:
Write:
Reset:
DDRG7
0
Figure 13-24. Data Direction Register G (DDRG)
Data Sheet
202
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port G
DDRG7–DDRG0 — Data Direction Register G Bits
These read/write bits control port G data direction. Reset clears
DDRG7–DDRG0], configuring all port G pins as inputs.
1 = Corresponding port G pin configured as output
0 = Corresponding port G pin configured as input
NOTE:
Avoid glitches on port G pins by writing to the port G data register before changing
data direction register G bits from 0 to 1.
Figure 13-25 shows the port G I/O logic.
READ DDRG ($0445)
WRITE DDRG ($0445)
DDRGx
RESET
WRITE PTG ($0441)
PTGx
PTGx
READ PTG ($0441)
Figure 13-25. Port G I/O Circuit
When bit DDRGx is a 1, reading address $0441 reads the PTGx data latch. When
bit DDRGx is a 0, reading address $0441 reads the voltage level on the pin. The
data latch can always be written, regardless of the state of its data direction bit.
Table 13-8 summarizes the operation of the port G pins.
Table 13-8. Port G Pin Functions
Accesses
to DDRG
Accesses
to PTG
DDRG
Bit
PTG
Bit
I/O Pin
Mode
Read/Write
Read
Pin
Write
X(1)
X
Input, Hi-Z(2)
Output
PTG7–PTG0(3)
PTG7–PTG0
0
1
DDRG7–DDRG0
DDRG7–DDRG0
PTG7–PTG0
1. X = Don’t care
2. Hi-Z = High impedance
3. Writing affects data register, but does not affect input.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Input/Output (I/O) Ports
Data Sheet
203
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Data Sheet
204
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Input/Output (I/O) Ports
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 14. Enhanced Serial Communications Interface (ESCI) Module
14.1 Introduction
The enhanced serial communications interface (ESCI) module allows
asynchronous communications with peripheral devices and other microcontroller
units (MCU).
14.2 Features
Features include:
•
•
•
•
•
•
Full-duplex operation
Standard mark/space non-return-to-zero (NRZ) format
Programmable baud rates
Programmable 8-bit or 9-bit character length
Separately enabled transmitter and receiver
Separate receiver and transmitter central processor unit (CPU) interrupt
requests
•
•
Programmable transmitter output polarity
Two receiver wakeup methods:
–
–
Idle line wakeup
Address mark wakeup
•
Interrupt-driven operation with eight interrupt flags:
–
–
–
–
–
–
–
–
Transmitter empty
Transmission complete
Receiver full
Idle receiver input
Receiver overrun
Noise error
Framing error
Parity error
•
•
•
Receiver framing error detection
Hardware parity checking
1/16 bit-time noise detection
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Enhanced Serial Communications Interface (ESCI) Module
Data Sheet
205
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI)
P O R T B
R B D D
P O R T F
D D R F
P O R T G
D D R G
P O R T A
D D R A
P O R T C
R C D D
P O R T E
D D R E
D
P O R T
D D R D
Data Sheet
206
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Pin Name Conventions
14.3 Pin Name Conventions
The generic names of the ESCI input/output (I/O) pins are:
•
•
RxD (receive data)
TxD (transmit data)
ESCI I/O lines are implemented by sharing parallel I/O port pins. The full name of
an ESCI input or output reflects the name of the shared port pin. Table 14-1 shows
the full names and the generic names of the ESCI I/O pins. The generic pin names
appear in the text of this section.
Table 14-1. Pin Name Conventions
Generic Pin Names
Full Pin Names
RxD
TxD
PTE1/RxD
PTE0/TxD
14.4 Functional Description
Figure 14-2 shows the structure of the ESCI module. The ESCI allows full-duplex,
asynchronous, NRZ serial communication between the MCU and remote devices,
including other MCUs. The transmitter and receiver of the ESCI operate
independently, although they use the same baud rate generator. During normal
operation, the CPU monitors the status of the ESCI, writes the data to be
transmitted, and processes received data.
The baud rate clock source for the ESCI can be selected via the configuration bit,
SCIBDSRC, of the CONFIG2 register ($001E)
For reference, a summary of the ESCI module input/output registers is provided in
Figure 14-3.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
207
MOTOROLA
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
INTERNAL BUS
ESCI DATA
REGISTER
ESCI DATA
REGISTER
RxD
SCI_TxD
TxD
RECEIVE
RxD
TRANSMIT
SHIFT REGISTER
SHIFT REGISTER
BUS_CLK
TXINV
LINR
SCTIE
TCIE
R8
T8
SL
SCRIE
ILIE
ACLK BIT
IN SCIACTL
TE
SCTE
RE
TC
RWU
SCRF
IDLE
OR
NF
FE
PE
ORIE
NEIE
FEIE
PEIE
SBK
LOOPS
ENSCI
LOOPS
RECEIVE
CONTROL
FLAG
CONTROL
TRANSMIT
CONTROL
WAKEUP
CONTROL
M
BKF
RPF
BUS
CLOCK
LINT
ENSCI
WAKE
ILTY
PEN
PTY
ENHANCED
PRESCALER
CGMXCLK
PRE- BAUD RATE
SCALER GENERATOR
÷ 4
SL
DATA SELECTION
CONTROL
÷ 16
SL = 1 -> SCI_CLK = BUSCLK
SL = 0 -> SCI_CLK = CGMXCLK (4x BUSCLK)
Figure 14-2. ESCI Module Block Diagram
Data Sheet
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module MOTOROLA
208
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
Addr.
Register Name
Bit 7
PDS2
0
6
5
PDS0
0
4
PSSB4
0
3
2
1
Bit 0
Read:
ESCI Prescaler Register
PDS1
PSSB3
PSSB2
PSSB1
PSSB0
$0009
(SCPSC) Write:
See page 234.
Reset:
Read:
0
0
0
0
0
ALOST
AFIN
ARUN
AROVFL
ARD8
ESCI Arbiter Control
AM1
AM0
ACLK
$000A
$000B
$0013
$0014
$0015
$0016
$0017
$0018
$0019
Register (SCIACTL) Write:
See page 237.
Reset:
0
0
0
0
0
0
0
0
Read:
ARD7
ARD6
ARD5
ARD4
ARD3
ARD2
ARD1
ARD0
ESCI Arbiter Data
Register (SCIADAT) Write:
See page 238.
Reset:
0
0
ENSCI
0
0
0
M
0
WAKE
0
0
ILTY
0
0
PEN
0
0
PTY
0
Read:
ESCI Control Register 1
LOOPS
0
TXINV
(SCC1) Write:
See page 223.
Reset:
0
0
Read:
ESCI Control Register 2
SCTIE
TCIE
0
SCRIE
ILIE
0
TE
RE
0
RWU
0
SBK
0
(SCC2) Write:
See page 225.
Reset:
0
0
0
Read:
R8
ESCI Control Register 3
T8
R
R
ORIE
NEIE
FEIE
PEIE
(SCC3) Write:
See page 227.
Reset:
U
0
0
0
0
0
0
0
Read:
SCTE
TC
SCRF
IDLE
OR
NF
FE
PE
ESCI Status Register 1
(SCS1) Write:
See page 228.
Reset:
1
0
1
0
0
0
0
0
0
0
0
0
0
0
Read:
BKF
RPF
ESCI Status Register 2
(SCS2) Write:
See page 231.
Reset:
0
0
0
0
0
0
0
0
Read:
R7
T7
R6
T6
R5
T5
R4
T4
R3
T3
R2
T2
R1
T1
R0
T0
ESCI Data Register
(SCDR) Write:
See page 231.
Reset:
Unaffected by reset
Read:
ESCI Baud Rate Register
LINT
0
LINR
0
SCP1
0
SCP0
R
SCR2
0
SCR1
0
SCR0
0
(SCBR) Write:
See page 232.
Reset:
0
0
= Unimplemented
R
= Reserved
Figure 14-3. ESCI I/O Register Summary
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Enhanced Serial Communications Interface (ESCI) Module
Data Sheet
209
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
14.4.1 Data Format
The SCI uses the standard non-return-to-zero mark/space data format illustrated
in Figure 14-4.
PARITY
OR DATA
BIT
8-BIT DATA FORMAT
(BIT M IN SCC1 CLEAR)
NEXT
START
BIT
START
BIT
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5 BIT 6
BIT 7
STOP
BIT
PARITY
OR DATA
BIT
9-BIT DATA FORMAT
(BIT M IN SCC1 SET)
NEXT
START
BIT
START
BIT
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5 BIT 6
BIT 7
BIT 8
STOP
BIT
Figure 14-4. SCI Data Formats
14.4.2 Transmitter
Figure 14-5 shows the structure of the SCI transmitter and the registers are
summarized in Figure 14-3. The baud rate clock source for the ESCI can be
selected via the configuration bit, ESCIBDSRC.
14.4.2.1 Character Length
The transmitter can accommodate either 8-bit or 9-bit data. The state of the M bit
in ESCI control register 1 (SCC1) determines character length. When transmitting
9-bit data, bit T8 in ESCI control register 3 (SCC3) is the ninth bit (bit 8).
14.4.2.2 Character Transmission
During an ESCI transmission, the transmit shift register shifts a character out to the
TxD pin. The ESCI data register (SCDR) is the write-only buffer between the
internal data bus and the transmit shift register.
To initiate an ESCI transmission:
1. Enable the ESCI by writing a 1 to the enable ESCI bit (ENSCI) in ESCI
control register 1 (SCC1).
2. Enable the transmitter by writing a 1 to the transmitter enable bit (TE) in
ESCI control register 2 (SCC2).
3. Clear the ESCI transmitter empty bit (SCTE) by first reading ESCI status
register 1 (SCS1) and then writing to the SCDR. For 9-bit data, also write the
T8 bit in SCC3.
4. Repeat step 3 for each subsequent transmission.
Data Sheet
210
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
INTERNAL BUS
PRE- BAUD
SCALER DIVIDER
÷ 16
÷ 4
ESCI DATA REGISTER
SCP1
SCP0
SCR2
SCR1
SCR0
11-BIT
TRANSMIT
SHIFT REGISTER
H
8
7
6
5
4
3
2
1
0
L
SCI_TxD
TXINV
M
PDS2
PDS1
PEN
PTY
PARITY
GENERATION
T8
CGMXCLK
OR
BUS CLOCK
PDS0
PSSB4
PSSB3
PSSB2
PSSB1
PSSB0
TRANSMITTER
CONTROL LOGIC
TRANSMITTER CPU
INTERRUPT REQUEST
SCTE
SBK
SCTE
LOOPS
ENSCI
TE
SCTIE
SCTIE
TC
TC
TCIE
TCIE
LINT
Figure 14-5. ESCI Transmitter
At the start of a transmission, transmitter control logic automatically loads the
transmit shift register with a preamble of 1s. After the preamble shifts out, control
logic transfers the SCDR data into the transmit shift register. A 0 start bit
automatically goes into the least significant bit (LSB) position of the transmit shift
register. A 1 stop bit goes into the most significant bit (MSB) position.
The ESCI transmitter empty bit, SCTE, in SCS1 becomes set when the SCDR
transfers a byte to the transmit shift register. The SCTE bit indicates that the SCDR
can accept new data from the internal data bus. If the ESCI transmit interrupt
enable bit, SCTIE, in SCC2 is also set, the SCTE bit generates a transmitter CPU
interrupt request.
When the transmit shift register is not transmitting a character, the TxD pin goes to
the idle condition, high. If at any time software clears the ENSCI bit in ESCI control
register 1 (SCC1), the transmitter and receiver relinquish control of the port E pins.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Enhanced Serial Communications Interface (ESCI) Module
Data Sheet
211
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
14.4.2.3 Break Characters
Writing a 1 to the send break bit, SBK, in SCC2 loads the transmit shift register with
a break character. For TXINV = 0 (output not inverted), a transmitted break
character contains all 0s and has no start, stop, or parity bit. Break character length
depends on the M bit in SCC1 and the LINR bits in SCBR. As long as SBK is at 1,
transmitter logic continuously loads break characters into the transmit shift register.
After software clears the SBK bit, the shift register finishes transmitting the last
break character and then transmits at least one 1. The automatic 1 at the end of a
break character guarantees the recognition of the start bit of the next character.
When LINR is cleared in SCBR, the ESCI recognizes a break character when a
start bit is followed by eight or nine 0 data bits and a 0 where the stop bit should
be, resulting in a total of 10 or 11 consecutive 0 data bits. When LINR is set in
SCBR, the ESCI recognizes a break character when a start bit is followed by 9
or 10 0 data bits and a 0 where the stop bit should be, resulting in a total of 11 or
12 consecutive 0 data bits.
Receiving a break character has these effects on ESCI registers:
•
•
•
•
•
•
Sets the framing error bit (FE) in SCS1
Sets the ESCI receiver full bit (SCRF) in SCS1
Clears the ESCI data register (SCDR)
Clears the R8 bit in SCC3
Sets the break flag bit (BKF) in SCS2
May set the overrun (OR), noise flag (NF), parity error (PE),
or reception in progress flag (RPF) bits
14.4.2.4 Idle Characters
For TXINV = 0 (output not inverted), a transmitted idle character contains all 1s and
has no start, stop, or parity bit. Idle character length depends on the M bit in SCC1.
The preamble is a synchronizing idle character that begins every transmission.
If the TE bit is cleared during a transmission, the TxD pin becomes idle after
completion of the transmission in progress. Clearing and then setting the TE bit
during a transmission queues an idle character to be sent after the character
currently being transmitted.
NOTE:
When a break sequence is followed immediately by an idle character, this SCI
design exhibits a condition in which the break character length is reduced by one
half bit time. In this instance, the break sequence will consist of a valid start bit,
eight or nine data bits (as defined by the M bit in SCC1) of 0 and one half data bit
length of 0 in the stop bit position followed immediately by the idle character. To
ensure a break character of the proper length is transmitted, always queue up a
byte of data to be transmitted while the final break sequence is in progress.
Data Sheet
212
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
When queueing an idle character, return the TE bit to 1 before the stop bit of the
current character shifts out to the TxD pin. Setting TE after the stop bit appears on
TxD causes data previously written to the SCDR to be lost. A good time to toggle
the TE bit for a queued idle character is when the SCTE bit becomes set and just
before writing the next byte to the SCDR.
14.4.2.5 Inversion of Transmitted Output
The transmit inversion bit (TXINV) in ESCI control register 1 (SCC1) reverses
the polarity of transmitted data. All transmitted values including idle, break,
start, and stop bits, are inverted when TXINV is at 1. See 14.8.1 ESCI Control
Register 1.
14.4.2.6 Transmitter Interrupts
These conditions can generate CPU interrupt requests from the ESCI transmitter:
•
ESCI transmitter empty (SCTE) — The SCTE bit in SCS1 indicates that the
SCDR has transferred a character to the transmit shift register. SCTE can
generate a transmitter CPU interrupt request. Setting the ESCI transmit
interrupt enable bit, SCTIE, in SCC2 enables the SCTE bit to generate
transmitter CPU interrupt requests.
•
Transmission complete (TC) — The TC bit in SCS1 indicates that the
transmit shift register and the SCDR are empty and that no break or idle
character has been generated. The transmission complete interrupt enable
bit, TCIE, in SCC2 enables the TC bit to generate transmitter CPU interrupt
requests.
14.4.3 Receiver
Figure 14-6 shows the structure of the ESCI receiver. The receiver I/O registers
are summarized in Figure 14-3.
14.4.3.1 Character Length
The receiver can accommodate either 8-bit or 9-bit data. The state of the M bit in
ESCI control register 1 (SCC1) determines character length. When receiving 9-bit
data, bit R8 in ESCI control register 3 (SCC3) is the ninth bit (bit 8). When receiving
8-bit data, bit R8 is a copy of the eighth bit (bit 7).
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
213
MOTOROLA
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
INTERNAL BUS
LINR
SCP1
SCP0
SCR2
SCR1
SCR0
ESCI DATA REGISTER
PRE- BAUD
SCALER DIVIDER
÷ 4
÷ 16
11-BIT
RECEIVE SHIFT REGISTER
DATA
RECOVERY
H
8
7
6
5
4
3
2
1
0
L
RxD
ALL ZEROS
BKF
RPF
PDS2
PDS1
CGMXCLK
OR
BUS CLOCK
PDS0
M
RWU
PSSB4
PSSB3
PSSB2
PSSB1
PSSB0
SCRF
IDLE
WAKE
ILTY
WAKEUP
LOGIC
PEN
PTY
R8
PARITY
CHECKING
IDLE
ILIE
ILIE
CPU INTERRUPT
REQUEST
SCRF
SCRIE
SCRIE
OR
OR
ORIE
ORIE
NF
NF
NEIE
NEIE
ERROR CPU
INTERRUPT REQUEST
FE
FE
FEIE
FEIE
PE
PE
PEIE
PEIE
Figure 14-6. ESCI Receiver Block Diagram
Data Sheet
214
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
14.4.3.2 Character Reception
During an ESCI reception, the receive shift register shifts characters in from the
RxD pin. The ESCI data register (SCDR) is the read-only buffer between the
internal data bus and the receive shift register.
After a complete character shifts into the receive shift register, the data portion of
the character transfers to the SCDR. The ESCI receiver full bit, SCRF, in ESCI
status register 1 (SCS1) becomes set, indicating that the received byte can be
read. If the ESCI receive interrupt enable bit, SCRIE, in SCC2 is also set, the SCRF
bit generates a receiver CPU interrupt request.
14.4.3.3 Data Sampling
The receiver samples the RxD pin at the RT clock rate. The RT clock is an internal
signal with a frequency 16 times the baud rate. To adjust for baud rate mismatch,
the RT clock is resynchronized at these times (see Figure 14-7):
•
•
After every start bit
After the receiver detects a data bit change from 1 to 0 (after the majority of
data bit samples at RT8, RT9, and RT10 returns a valid 1 and the majority
of the next RT8, RT9, and RT10 samples returns a valid 0)
To locate the start bit, data recovery logic does an asynchronous search for a 0
preceded by three 1s. When the falling edge of a possible start bit occurs, the RT
clock begins to count to 16.
START BIT
LSB
RxD
START BIT
QUALIFICATION
START BIT DATA
VERIFICATION SAMPLING
SAMPLES
RT
CLOCK
RT CLOCK
STATE
RT CLOCK
RESET
Figure 14-7. Receiver Data Sampling
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Enhanced Serial Communications Interface (ESCI) Module
Data Sheet
215
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
To verify the start bit and to detect noise, data recovery logic takes samples at RT3,
RT5, and RT7. Table 14-2 summarizes the results of the start bit verification
samples.
Table 14-2. Start Bit Verification
RT3, RT5, and RT7 Samples Start Bit Verification Noise Flag
000
001
010
011
100
101
110
111
Yes
Yes
Yes
No
0
1
1
0
1
0
0
0
Yes
No
No
No
If start bit verification is not successful, the RT clock is reset and a new search for
a start bit begins.
To determine the value of a data bit and to detect noise, recovery logic takes
samples at RT8, RT9, and RT10. Table 14-3 summarizes the results of the data
bit samples.
Table 14-3. Data Bit Recovery
RT8, RT9, and RT10 Samples Data Bit Determination Noise Flag
000
001
010
011
100
101
110
111
0
0
0
1
0
1
1
1
0
1
1
1
1
1
1
0
NOTE:
The RT8, RT9, and RT10 samples do not affect start bit verification. If any or all of
the RT8, RT9, and RT10 start bit samples are 1s following a successful start bit
verification, the noise flag (NF) is set and the receiver assumes that the bit is a start
bit.
Data Sheet
216
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
To verify a stop bit and to detect noise, recovery logic takes samples at RT8, RT9,
and RT10. Table 14-4 summarizes the results of the stop bit samples.
Table 14-4. Stop Bit Recovery
RT8, RT9, and RT10 Samples Framing Error Flag Noise Flag
000
001
010
011
100
101
110
111
1
1
1
0
1
0
0
0
0
1
1
1
1
1
1
0
14.4.3.4 Framing Errors
If the data recovery logic does not detect a 1 where the stop bit should be in an
incoming character, it sets the framing error bit, FE, in SCS1. A break character
also sets the FE bit because a break character has no stop bit. The FE bit is set at
the same time that the SCRF bit is set.
14.4.3.5 Baud Rate Tolerance
A transmitting device may be operating at a baud rate below or above the receiver
baud rate. Accumulated bit time misalignment can cause one of the three stop bit
data samples to fall outside the actual stop bit. Then a noise error occurs. If more
than one of the samples is outside the stop bit, a framing error occurs. In most
applications, the baud rate tolerance is much more than the degree of
misalignment that is likely to occur.
As the receiver samples an incoming character, it resynchronizes the RT clock on
any valid falling edge within the character. Resynchronization within characters
corrects misalignments between transmitter bit times and receiver bit times.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
217
MOTOROLA
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Slow Data Tolerance
Figure 14-8 shows how much a slow received character can be misaligned
without causing a noise error or a framing error. The slow stop bit begins at RT8
instead of RT1 but arrives in time for the stop bit data samples at RT8, RT9, and
RT10.
MSB
STOP
RECEIVER
RT CLOCK
DATA
SAMPLES
Figure 14-8. Slow Data
For an 8-bit character, data sampling of the stop bit takes the receiver
9 bit times × 16 RT cycles + 10 RT cycles = 154 RT cycles.
With the misaligned character shown in Figure 14-8, the receiver counts
154 RT cycles at the point when the count of the transmitting device is
9 bit times × 16 RT cycles + 3 RT cycles = 147 RT cycles.
The maximum percent difference between the receiver count and the
transmitter count of a slow 8-bit character with no errors is:
154 – 147
× 100 = 4.54%
-------------------------
154
For a 9-bit character, data sampling of the stop bit takes the receiver
10 bit times × 16 RT cycles + 10 RT cycles = 170 RT cycles.
With the misaligned character shown in Figure 14-8, the receiver counts
170 RT cycles at the point when the count of the transmitting device is
10 bit times × 16 RT cycles + 3 RT cycles = 163 RT cycles.
The maximum percent difference between the receiver count and the
transmitter count of a slow 9-bit character with no errors is:
170 – 163
× 100 = 4.12%
-------------------------
170
Data Sheet
218
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
Fast Data Tolerance
Figure 14-9 shows how much a fast received character can be misaligned
without causing a noise error or a framing error. The fast stop bit ends at RT10
instead of RT16 but is still there for the stop bit data samples at RT8, RT9,
and RT10.
STOP
IDLE OR NEXT CHARACTER
RECEIVER
RT CLOCK
DATA
SAMPLES
Figure 14-9. Fast Data
For an 8-bit character, data sampling of the stop bit takes the receiver
9 bit times × 16 RT cycles + 10 RT cycles = 154 RT cycles.
With the misaligned character shown in Figure 14-9, the receiver counts
154 RT cycles at the point when the count of the transmitting device is
10 bit times × 16 RT cycles = 160 RT cycles.
The maximum percent difference between the receiver count and the
transmitter count of a fast 8-bit character with no errors is
154 – 160
× 100 = 3.90%.
-------------------------
154
For a 9-bit character, data sampling of the stop bit takes the receiver
10 bit times × 16 RT cycles + 10 RT cycles = 170 RT cycles.
With the misaligned character shown in Figure 14-9, the receiver counts
170 RT cycles at the point when the count of the transmitting device is
11 bit times × 16 RT cycles = 176 RT cycles.
The maximum percent difference between the receiver count and the
transmitter count of a fast 9-bit character with no errors is:
170 – 176
× 100 = 3.53%.
-------------------------
170
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
219
MOTOROLA
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
14.4.3.6 Receiver Wakeup
So that the MCU can ignore transmissions intended only for other receivers in
multiple-receiver systems, the receiver can be put into a standby state. Setting the
receiver wakeup bit, RWU, in SCC2 puts the receiver into a standby state during
which receiver interrupts are disabled.
Depending on the state of the WAKE bit in SCC1, either of two conditions on the
RxD pin can bring the receiver out of the standby state:
1. Address mark — An address mark is a 1 in the MSB position of a received
character. When the WAKE bit is set, an address mark wakes the receiver
from the standby state by clearing the RWU bit. The address mark also sets
the ESCI receiver full bit, SCRF. Software can then compare the character
containing the address mark to the user-defined address of the receiver. If
they are the same, the receiver remains awake and processes the
characters that follow. If they are not the same, software can set the RWU
bit and put the receiver back into the standby state.
2. Idle input line condition — When the WAKE bit is clear, an idle character on
the RxD pin wakes the receiver from the standby state by clearing the RWU
bit. The idle character that wakes the receiver does not set the receiver idle
bit, IDLE, or the ESCI receiver full bit, SCRF. The idle line type bit, ILTY,
determines whether the receiver begins counting 1s as idle character bits
after the start bit or after the stop bit.
NOTE:
With the WAKE bit clear, setting the RWU bit after the RxD pin has been idle will
cause the receiver to wake up.
14.4.3.7 Receiver Interrupts
These sources can generate CPU interrupt requests from the ESCI receiver:
•
ESCI receiver full (SCRF) — The SCRF bit in SCS1 indicates that the
receive shift register has transferred a character to the SCDR. SCRF can
generate a receiver CPU interrupt request. Setting the ESCI receive
interrupt enable bit, SCRIE, in SCC2 enables the SCRF bit to generate
receiver CPU interrupts.
•
Idle input (IDLE) — The IDLE bit in SCS1 indicates that 10 or 11 consecutive
1s shifted in from the RxD pin. The idle line interrupt enable bit, ILIE, in
SCC2 enables the IDLE bit to generate CPU interrupt requests.
14.4.3.8 Error Interrupts
These receiver error flags in SCS1 can generate CPU interrupt requests:
•
Receiver overrun (OR) — The OR bit indicates that the receive shift register
shifted in a new character before the previous character was read from the
SCDR. The previous character remains in the SCDR, and the new character
is lost. The overrun interrupt enable bit, ORIE, in SCC3 enables OR to
generate ESCI error CPU interrupt requests.
Data Sheet
220
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Low-Power Modes
•
Noise flag (NF) — The NF bit is set when the ESCI detects noise on
incoming data or break characters, including start, data, and stop bits. The
noise error interrupt enable bit, NEIE, in SCC3 enables NF to generate ESCI
error CPU interrupt requests.
•
•
Framing error (FE) — The FE bit in SCS1 is set when a 0 occurs where the
receiver expects a stop bit. The framing error interrupt enable bit, FEIE, in
SCC3 enables FE to generate ESCI error CPU interrupt requests.
Parity error (PE) — The PE bit in SCS1 is set when the ESCI detects a parity
error in incoming data. The parity error interrupt enable bit, PEIE, in SCC3
enables PE to generate ESCI error CPU interrupt requests.
14.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power-consumption standby
modes.
14.5.1 Wait Mode
The ESCI module remains active in wait mode. Any enabled CPU interrupt request
from the ESCI module can bring the MCU out of wait mode.
If ESCI module functions are not required during wait mode, reduce power
consumption by disabling the module before executing the WAIT instruction.
14.5.2 Stop Mode
The ESCI module is inactive in stop mode. The STOP instruction does not affect
:
ESCI register states. ESCI module operation resumes after the MCU exits stop
mode.
Because the internal clock is inactive during stop mode, entering stop mode during
an ESCI transmission or reception results in invalid data.
14.6 ESCI During Break Module Interrupts
The BCFE bit in the break flag control register (SBFCR) enables software to clear
status bits during the break state. See 20.2 Break Module (BRK).
To allow software to clear status bits during a break interrupt, write a 1 to the BCFE
bit. If a status bit is cleared during the break state, it remains cleared when the MCU
exits the break state.
To protect status bits during the break state, write a 0 to the BCFE bit. With BCFE
at 0 (its default state), software can read and write I/O registers during the break
state without affecting status bits. Some status bits have a two-step read/write
clearing procedure. If software does the first step on such a bit before the break,
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
221
MOTOROLA
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
the bit cannot change during the break state as long as BCFE is at 0. After the
break, doing the second step clears the status bit.
14.7 I/O Signals
Port E shares two of its pins with the ESCI module. The two ESCI I/O pins are:
•
•
PTE0/TxD — transmit data
PTE1/RxD — receive data
14.7.1 PTE0/TxD (Transmit Data)
The PTE0/TxD pin is the serial data output from the ESCI transmitter. The ESCI
shares the PTE0/TxD pin with port E. When the ESCI is enabled, the PTE0/TxD
pin is an output regardless of the state of the DDRE0 bit in data direction register E
(DDRE).
14.7.2 PTE1/RxD (Receive Data)
The PTE1/RxD pin is the serial data input to the ESCI receiver. The ESCI shares
the PTE1/RxD pin with port E. When the ESCI is enabled, the PTE1/RxD pin is an
input regardless of the state of the DDRE1 bit in data direction register E (DDRE).
14.8 I/O Registers
These I/O registers control and monitor ESCI operation:
•
•
•
•
•
•
•
•
•
•
ESCI control register 1, SCC1
ESCI control register 2, SCC2
ESCI control register 3, SCC3
ESCI status register 1, SCS1
ESCI status register 2, SCS2
ESCI data register, SCDR
ESCI baud rate register, SCBR
ESCI prescaler register, SCPSC
ESCI arbiter control register, SCIACTL
ESCI arbiter data register, SCIADAT
Data Sheet
222
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
14.8.1 ESCI Control Register 1
ESCI control register 1 (SCC1):
•
•
•
•
•
•
•
•
Enables loop mode operation
Enables the ESCI
Controls output polarity
Controls character length
Controls ESCI wakeup method
Controls idle character detection
Enables parity function
Controls parity type
Address: $0013
Bit 7
6
ENSCI
0
5
TXINV
0
4
M
0
3
WAKE
0
2
ILTY
0
1
PEN
0
Bit 0
PTY
0
Read:
Write:
Reset:
LOOPS
0
Figure 14-10. ESCI Control Register 1 (SCC1)
LOOPS — Loop Mode Select Bit
This read/write bit enables loop mode operation. In loop mode the RxD pin is
disconnected from the ESCI, and the transmitter output goes into the receiver
input. Both the transmitter and the receiver must be enabled to use loop mode.
Reset clears the LOOPS bit.
1 = Loop mode enabled
0 = Normal operation enabled
ENSCI — Enable ESCI Bit
This read/write bit enables the ESCI and the ESCI baud rate generator. Clearing
ENSCI sets the SCTE and TC bits in ESCI status register 1 and disables
transmitter interrupts. Reset clears the ENSCI bit.
1 = ESCI enabled
0 = ESCI disabled
TXINV — Transmit Inversion Bit
This read/write bit reverses the polarity of transmitted data. Reset clears the
TXINV bit.
1 = Transmitter output inverted
0 = Transmitter output not inverted
NOTE:
Setting the TXINV bit inverts all transmitted values including idle, break, start, and
stop bits.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Enhanced Serial Communications Interface (ESCI) Module
Data Sheet
223
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
M — Mode (Character Length) Bit
This read/write bit determines whether ESCI characters are eight or nine bits
long (See Table 14-5).The ninth bit can serve as a receiver wakeup signal or as
a parity bit. Reset clears the M bit.
1 = 9-bit ESCI characters
0 = 8-bit ESCI characters
Table 14-5. Character Format Selection
Control Bits
Character Format
M
0
1
0
0
1
1
PEN:PTY Start Bits Data Bits Parity Stop Bits Character Length
0 X
0 X
1 0
1 1
1 0
1 1
1
1
1
1
1
1
8
9
7
7
8
8
None
None
Even
Odd
1
1
1
1
1
1
10 bits
11 bits
10 bits
10 bits
11 bits
11 bits
Even
Odd
WAKE — Wakeup Condition Bit
This read/write bit determines which condition wakes up the ESCI: a 1 (address
mark) in the MSB position of a received character or an idle condition on the
RxD pin. Reset clears the WAKE bit.
1 = Address mark wakeup
0 = Idle line wakeup
ILTY — Idle Line Type Bit
This read/write bit determines when the ESCI starts counting 1s as idle
character bits. The counting begins either after the start bit or after the stop bit.
If the count begins after the start bit, then a string of 1s preceding the stop bit
may cause false recognition of an idle character. Beginning the count after the
stop bit avoids false idle character recognition, but requires properly
synchronized transmissions. Reset clears the ILTY bit.
1 = Idle character bit count begins after stop bit
0 = Idle character bit count begins after start bit
PEN — Parity Enable Bit
This read/write bit enables the ESCI parity function (see Table 14-5).
When enabled, the parity function inserts a parity bit in the MSB position (see
Table 14-3). Reset clears the PEN bit.
1 = Parity function enabled
0 = Parity function disabled
PTY — Parity Bit
This read/write bit determines whether the ESCI generates and checks for odd
parity or even parity (see Table 14-5). Reset clears the PTY bit.
1 = Odd parity
0 = Even parity
NOTE:
Changing the PTY bit in the middle of a transmission or reception can generate a
parity error.
Data Sheet
224
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
14.8.2 ESCI Control Register 2
ESCI control register 2 (SCC2):
•
Enables these CPU interrupt requests:
–
–
–
–
SCTE bit to generate transmitter CPU interrupt requests
TC bit to generate transmitter CPU interrupt requests
SCRF bit to generate receiver CPU interrupt requests
IDLE bit to generate receiver CPU interrupt requests
•
•
•
•
Enables the transmitter
Enables the receiver
Enables ESCI wakeup
Transmits ESCI break characters
Address: $0014
Bit 7
6
TCIE
0
5
SCRIE
0
4
ILIE
0
3
TE
0
2
RE
0
1
RWU
0
Bit 0
SBK
0
Read:
Write:
Reset:
SCTIE
0
Figure 14-11. ESCI Control Register 2 (SCC2)
SCTIE — ESCI Transmit Interrupt Enable Bit
This read/write bit enables the SCTE bit to generate ESCI transmitter CPU
interrupt requests. Setting the SCTIE bit in SCC2 enables the SCTE bit to
generate CPU interrupt requests. Reset clears the SCTIE bit.
1 = SCTE enabled to generate CPU interrupt
0 = SCTE not enabled to generate CPU interrupt
TCIE — Transmission Complete Interrupt Enable Bit
This read/write bit enables the TC bit to generate ESCI transmitter CPU
interrupt requests. Reset clears the TCIE bit.
1 = TC enabled to generate CPU interrupt requests
0 = TC not enabled to generate CPU interrupt requests
SCRIE — ESCI Receive Interrupt Enable Bit
This read/write bit enables the SCRF bit to generate ESCI receiver CPU
interrupt requests. Setting the SCRIE bit in SCC2 enables the SCRF bit to
generate CPU interrupt requests. Reset clears the SCRIE bit.
1 = SCRF enabled to generate CPU interrupt
0 = SCRF not enabled to generate CPU interrupt
ILIE — Idle Line Interrupt Enable Bit
This read/write bit enables the IDLE bit to generate ESCI receiver CPU interrupt
requests. Reset clears the ILIE bit.
1 = IDLE enabled to generate CPU interrupt requests
0 = IDLE not enabled to generate CPU interrupt requests
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
225
MOTOROLA
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
TE — Transmitter Enable Bit
Setting this read/write bit begins the transmission by sending a preamble of
10 or 11 1s from the transmit shift register to the TxD pin. If software clears the
TE bit, the transmitter completes any transmission in progress before the TxD
returns to the idle condition (high). Clearing and then setting TE during a
transmission queues an idle character to be sent after the character currently
being transmitted. Reset clears the TE bit.
1 = Transmitter enabled
0 = Transmitter disabled
NOTE:
NOTE:
Writing to the TE bit is not allowed when the enable ESCI bit (ENSCI) is clear.
ENSCI is in ESCI control register 1.
RE — Receiver Enable Bit
Setting this read/write bit enables the receiver. Clearing the RE bit disables the
receiver but does not affect receiver interrupt flag bits. Reset clears the RE bit.
1 = Receiver enabled
0 = Receiver disabled
Writing to the RE bit is not allowed when the enable ESCI bit (ENSCI) is clear.
ENSCI is in ESCI control register 1.
RWU — Receiver Wakeup Bit
This read/write bit puts the receiver in a standby state during which receiver
interrupts are disabled. The WAKE bit in SCC1 determines whether an idle input
or an address mark brings the receiver out of the standby state and clears the
RWU bit. Reset clears the RWU bit.
1 = Standby state
0 = Normal operation
SBK — Send Break Bit
Setting and then clearing this read/write bit transmits a break character followed
by a 1. The 1 after the break character guarantees recognition of a valid start
bit. If SBK remains set, the transmitter continuously transmits break characters
with no 1s between them. Reset clears the SBK bit.
1 = Transmit break characters
0 = No break characters being transmitted
NOTE:
Do not toggle the SBK bit immediately after setting the SCTE bit. Toggling SBK
before the preamble begins causes the ESCI to send a break character instead of
a preamble.
Data Sheet
226
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
14.8.3 ESCI Control Register 3
ESCI control register 3 (SCC3):
•
Stores the ninth ESCI data bit received and the ninth ESCI data bit to be
transmitted.
•
Enables these interrupts:
–
–
–
–
Receiver overrun
Noise error
Framing error
Parity error
Address:
$0015
Bit 7
R8
6
T8
0
5
R
0
4
3
2
NEIE
0
1
FEIE
0
Bit 0
PEIE
0
Read:
Write:
Reset:
R
ORIE
U
0
0
= Unimplemented
R
= Reserved
U = Unaffected
Figure 14-12. ESCI Control Register 3 (SCC3)
R8 — Received Bit 8
When the ESCI is receiving 9-bit characters, R8 is the read-only ninth bit (bit 8)
of the received character. R8 is received at the same time that the SCDR
receives the other 8 bits.
When the ESCI is receiving 8-bit characters, R8 is a copy of the eighth bit (bit 7).
Reset has no effect on the R8 bit.
T8 — Transmitted Bit 8
When the ESCI is transmitting 9-bit characters, T8 is the read/write ninth bit
(bit 8) of the transmitted character. T8 is loaded into the transmit shift register at
the same time that the SCDR is loaded into the transmit shift register. Reset
clears the T8 bit.
ORIE — Receiver Overrun Interrupt Enable Bit
This read/write bit enables ESCI error CPU interrupt requests generated by the
receiver overrun bit, OR. Reset clears ORIE.
1 = ESCI error CPU interrupt requests from OR bit enabled
0 = ESCI error CPU interrupt requests from OR bit disabled
NEIE — Receiver Noise Error Interrupt Enable Bit
This read/write bit enables ESCI error CPU interrupt requests generated by the
noise error bit, NE. Reset clears NEIE.
1 = ESCI error CPU interrupt requests from NE bit enabled
0 = ESCI error CPU interrupt requests from NE bit disabled
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
227
MOTOROLA
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
FEIE — Receiver Framing Error Interrupt Enable Bit
This read/write bit enables ESCI error CPU interrupt requests generated by the
framing error bit, FE. Reset clears FEIE.
1 = ESCI error CPU interrupt requests from FE bit enabled
0 = ESCI error CPU interrupt requests from FE bit disabled
PEIE — Receiver Parity Error Interrupt Enable Bit
This read/write bit enables ESCI receiver CPU interrupt requests generated by
the parity error bit, PE. Reset clears PEIE.
1 = ESCI error CPU interrupt requests from PE bit enabled
0 = ESCI error CPU interrupt requests from PE bit disabled
14.8.4 ESCI Status Register 1
ESCI status register 1 (SCS1) contains flags to signal these conditions:
•
•
•
•
•
•
•
•
Transfer of SCDR data to transmit shift register complete
Transmission complete
Transfer of receive shift register data to SCDR complete
Receiver input idle
Receiver overrun
Noisy data
Framing error
Parity error
Address:
$0016
Bit 7
6
5
4
3
2
1
Bit 0
PE
Read:
Write:
Reset:
SCTE
TC
SCRF
IDLE
OR
NF
FE
1
1
0
0
0
0
0
0
= Unimplemented
Figure 14-13. ESCI Status Register 1 (SCS1)
SCTE — ESCI Transmitter Empty Bit
This clearable, read-only bit is set when the SCDR transfers a character to the
transmit shift register. SCTE can generate an ESCI transmitter CPU interrupt
request. When the SCTIE bit in SCC2 is set, SCTE generates an ESCI
transmitter CPU interrupt request. In normal operation, clear the SCTE bit by
reading SCS1 with SCTE set and then writing to SCDR. Reset sets the
SCTE bit.
1 = SCDR data transferred to transmit shift register
0 = SCDR data not transferred to transmit shift register
TC — Transmission Complete Bit
This read-only bit is set when the SCTE bit is set, and no data, preamble, or
break character is being transmitted. TC generates an ESCI transmitter CPU
interrupt request if the TCIE bit in SCC2 is also set. TC is cleared automatically
Data Sheet
228
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
when data, preamble, or break is queued and ready to be sent. There may be
up to 1.5 transmitter clocks of latency between queueing data, preamble, and
break and the transmission actually starting. Reset sets the TC bit.
1 = No transmission in progress
0 = Transmission in progress
SCRF — ESCI Receiver Full Bit
This clearable, read-only bit is set when the data in the receive shift register
transfers to the ESCI data register. SCRF can generate an ESCI receiver CPU
interrupt request. When the SCRIE bit in SCC2 is set the SCRF generates a
CPU interrupt request. In normal operation, clear the SCRF bit by reading SCS1
with SCRF set and then reading the SCDR. Reset clears SCRF.
1 = Received data available in SCDR
0 = Data not available in SCDR
IDLE — Receiver Idle Bit
This clearable, read-only bit is set when 10 or 11 consecutive 1s appear on the
receiver input. IDLE generates an ESCI receiver CPU interrupt request if the
ILIE bit in SCC2 is also set. Clear the IDLE bit by reading SCS1 with IDLE set
and then reading the SCDR. After the receiver is enabled, it must receive a valid
character that sets the SCRF bit before an idle condition can set the IDLE bit.
Also, after the IDLE bit has been cleared, a valid character must again set the
SCRF bit before an idle condition can set the IDLE bit. Reset clears the IDLE bit.
1 = Receiver input idle
0 = Receiver input active (or idle since the IDLE bit was cleared)
OR — Receiver Overrun Bit
This clearable, read-only bit is set when software fails to read the SCDR before
the receive shift register receives the next character. The OR bit generates an
ESCI error CPU interrupt request if the ORIE bit in SCC3 is also set. The data
in the shift register is lost, but the data already in the SCDR is not affected. Clear
the OR bit by reading SCS1 with OR set and then reading the SCDR. Reset
clears the OR bit.
1 = Receive shift register full and SCRF = 1
0 = No receiver overrun
Software latency may allow an overrun to occur between reads of SCS1 and
SCDR in the flag-clearing sequence. Figure 14-14 shows the normal
flag-clearing sequence and an example of an overrun caused by a delayed
flag-clearing sequence. The delayed read of SCDR does not clear the OR bit
because OR was not set when SCS1 was read. Byte 2 caused the overrun and
is lost. The next flag-clearing sequence reads byte 3 in the SCDR instead of
byte 2.
In applications that are subject to software latency or in which it is important to
know which byte is lost due to an overrun, the flag-clearing routine can check
the OR bit in a second read of SCS1 after reading the data register.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
229
MOTOROLA
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
NORMAL FLAG CLEARING SEQUENCE
BYTE 1
BYTE 2
BYTE 3
BYTE 4
READ SCS1
SCRF = 1
OR = 0
READ SCS1
SCRF = 1
OR = 0
READ SCS1
SCRF = 1
OR = 0
READ SCDR
BYTE 1
READ SCDR
BYTE 3
READ SCDR
BYTE 2
DELAYED FLAG CLEARING SEQUENCE
BYTE 1
BYTE 2
BYTE 3
BYTE 4
READ SCS1
SCRF = 1
OR = 0
READ SCS1
SCRF = 1
OR = 1
READ SCDR
BYTE 1
READ SCDR
BYTE 3
Figure 14-14. Flag Clearing Sequence
NF — Receiver Noise Flag Bit
This clearable, read-only bit is set when the ESCI detects noise on the RxD pin.
NF generates an NF CPU interrupt request if the NEIE bit in SCC3 is also set.
Clear the NF bit by reading SCS1 and then reading the SCDR. Reset clears the
NF bit.
1 = Noise detected
0 = No noise detected
FE — Receiver Framing Error Bit
This clearable, read-only bit is set when a 0 is accepted as the stop bit. FE
generates an ESCI error CPU interrupt request if the FEIE bit in SCC3 also is
set. Clear the FE bit by reading SCS1 with FE set and then reading the SCDR.
Reset clears the FE bit.
1 = Framing error detected
0 = No framing error detected
PE — Receiver Parity Error Bit
This clearable, read-only bit is set when the ESCI detects a parity error in
incoming data. PE generates a PE CPU interrupt request if the PEIE bit in SCC3
is also set. Clear the PE bit by reading SCS1 with PE set and then reading the
SCDR. Reset clears the PE bit.
1 = Parity error detected
0 = No parity error detected
Data Sheet
230
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
14.8.5 ESCI Status Register 2
ESCI status register 2 (SCS2) contains flags to signal these conditions:
•
•
Break character detected
Incoming data
Address:
$0017
Bit 7
0
6
0
5
0
4
0
3
0
2
0
1
Bit 0
RPF
Read:
Write:
Reset:
BKF
0
0
0
0
0
0
0
0
= Unimplemented
Figure 14-15. ESCI Status Register 2 (SCS2)
BKF — Break Flag Bit
This clearable, read-only bit is set when the ESCI detects a break character on
the RxD pin. In SCS1, the FE and SCRF bits are also set. In 9-bit character
transmissions, the R8 bit in SCC3 is cleared. BKF does not generate a CPU
interrupt request. Clear BKF by reading SCS2 with BKF set and then reading
the SCDR. Once cleared, BKF can become set again only after 1s again appear
on the RxD pin followed by another break character. Reset clears the BKF bit.
1 = Break character detected
0 = No break character detected
RPF — Reception in Progress Flag Bit
This read-only bit is set when the receiver detects a 0 during the RT1 time period
of the start bit search. RPF does not generate an interrupt request. RPF is reset
after the receiver detects false start bits (usually from noise or a baud rate
mismatch), or when the receiver detects an idle character. Polling RPF before
disabling the ESCI module or entering stop mode can show whether a reception
is in progress.
1 = Reception in progress
0 = No reception in progress
14.8.6 ESCI Data Register
The ESCI data register (SCDR) is the buffer between the internal data bus and the
receive and transmit shift registers. Reset has no effect on data in the ESCI data
register.
Address:
$0018
Bit 7
R7
6
5
4
3
2
1
Bit 0
R0
Read:
Write:
Reset:
R6
T6
R5
T5
R4
T4
R3
T3
R2
T2
R1
T1
T7
T0
Unaffected by reset
Figure 14-16. ESCI Data Register (SCDR)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Enhanced Serial Communications Interface (ESCI) Module
Data Sheet
231
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
R7/T7:R0/T0 — Receive/Transmit Data Bits
Reading address $0018 accesses the read-only received data bits, R7:R0.
Writing to address $0018 writes the data to be transmitted, T7:T0. Reset has no
effect on the ESCI data register.
NOTE:
Do not use read-modify-write instructions on the ESCI data register.
14.8.7 ESCI Baud Rate Register
The ESCI baud rate register (SCBR) together with the ESCI prescaler register
selects the baud rate for both the receiver and the transmitter.
NOTE:
There are two prescalers available to adjust the baud rate. One in the ESCI baud
rate register and one in the ESCI prescaler register.
Address:
$0019
Bit 7
6
5
SCP1
0
4
SCP0
0
3
R
0
2
SCR2
0
1
SCR1
0
Bit 0
SCR0
0
Read:
Write:
Reset:
LINT
LINR
0
0
R
= Reserved
Figure 14-17. ESCI Baud Rate Register (SCBR)
LINT — LIN Transmit Enable
This read/write bit selects the enhanced ESCI features for the local interconnect
network (LIN) protocol as shown in Table 14-6. Reset clears LINT.
LINR — LIN Receiver Bits
This read/write bit selects the enhanced ESCI features for the local interconnect
network (LIN) protocol as shown in Table 14-6. Reset clears LINR.
Table 14-6. ESCI LIN Control Bits
LINT
LINR
M
X
0
1
0
1
0
1
Functionality
Normal ESCI functionality
0
0
0
1
1
1
1
0
1
1
0
0
1
1
11-bit break detect enabled for LIN receiver
12-bit break detect enabled for LIN receiver
11-bit generation enabled for LIN transmitter
12-bit generation enabled for LIN transmitter
11-bit break detect/11-bit generation enabled for LIN
12-bit break detect/12-bit generation enabled for LIN
Data Sheet
232
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
In LIN (version 1.2) systems, the master node transmits a break character which
will appear as 11.05–14.95 dominant bits to the slave node. A data character of
0x00 sent from the master might appear as 7.65–10.35 dominant bit times. This
is due to the oscillator tolerance requirement that the slave node must be within
±15% of the master node's oscillator. Since a slave node cannot know if it is
running faster or slower than the master node (prior to synchronization), the
LINR bit allows the slave node to differentiate between a 0x00 character of
10.35 bits and a break character of 11.05 bits. The break symbol length must be
verified in software in any case, but the LINR bit serves as a filter, preventing
false detections of break characters that are really 0x00 data characters.
SCP1 and SCP0 — ESCI Baud Rate Register Prescaler Bits
These read/write bits select the baud rate register prescaler divisor as shown in
Table 14-7. Reset clears SCP1 and SCP0.
Table 14-7. ESCI Baud Rate Prescaling
Baud Rate Register
SCP[1:0]
Prescaler Divisor (BPD)
0 0
0 1
1 0
1 1
1
3
4
13
SCR2–SCR0 — ESCI Baud Rate Select Bits
These read/write bits select the ESCI baud rate divisor as shown in Table 14-8.
Reset clears SCR2–SCR0.
Table 14-8. ESCI Baud Rate Selection
SCR[2:1:0]
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
Baud Rate Divisor (BD)
1
2
4
8
16
32
64
128
14.8.8 ESCI Prescaler Register
The ESCI prescaler register (SCPSC) together with the ESCI baud rate register
selects the baud rate for both the receiver and the transmitter.
NOTE:
There are two prescalers available to adjust the baud rate. One in the ESCI baud
rate register and one in the ESCI prescaler register.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Enhanced Serial Communications Interface (ESCI) Module
Data Sheet
233
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
;
Address:
$0009
Bit 7
6
PDS1
0
5
PDS0
0
4
PSSB4
0
3
PSSB3
0
2
PSSB2
0
1
PSSB1
0
Bit 0
PSSB0
0
Read:
Write:
Reset:
PDS2
0
Figure 14-18. ESCI Prescaler Register (SCPSC)
PDS2–PDS0 — Prescaler Divisor Select Bits
These read/write bits select the prescaler divisor as shown in
Table 14-9. Reset clears PDS2–PDS0.
NOTE:
The setting of ‘000’ will bypass not only this prescaler but also the prescaler divisor
fine adjust (PDFA). It is not recommended to bypass the prescaler while ENSCI is
set, because the switching is not glitch free.
Table 14-9. ESCI Prescaler Division Ratio
PDS[2:1:0]
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
Prescaler Divisor (PD)
Bypass this prescaler
2
3
4
5
6
7
8
PSSB4–PSSB0 — Clock Insertion Select Bits
These read/write bits select the number of clocks inserted in each 32 output
cycle frame to achieve more timing resolution on the average prescaler
frequency as shown in Table 14-10. Reset clears PSSB4–PSSB0.
Table 14-10. ESCI Prescaler Divisor Fine Adjust
PSSB[4:3:2:1:0]
0 0 0 0 0
0 0 0 0 1
0 0 0 1 0
0 0 0 1 1
0 0 1 0 0
0 0 1 0 1
0 0 1 1 0
0 0 1 1 1
0 1 0 0 0
Prescaler Divisor Fine Adjust (PDFA)
0/32 = 0
1/32 = 0.03125
2/32 = 0.0625
3/32 = 0.09375
4/32 = 0.125
5/32 = 0.15625
6/32 = 0.1875
7/32 = 0.21875
8/32 = 0.25
Data Sheet
234
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
Table 14-10. ESCI Prescaler Divisor Fine Adjust (Continued)
PSSB[4:3:2:1:0]
0 1 0 0 1
0 1 0 1 0
0 1 0 1 1
0 1 1 0 0
0 1 1 0 1
0 1 1 1 0
0 1 1 1 1
1 0 0 0 0
1 0 0 0 1
1 0 0 1 0
1 0 0 1 1
1 0 1 0 0
1 0 1 0 1
1 0 1 1 0
1 0 1 1 1
1 1 0 0 0
1 1 0 0 1
1 1 0 1 0
1 1 0 1 1
1 1 1 0 0
1 1 1 0 1
1 1 1 1 0
1 1 1 1 1
Prescaler Divisor Fine Adjust (PDFA)
9/32 = 0.28125
10/32 = 0.3125
11/32 = 0.34375
12/32 = 0.375
13/32 = 0.40625
14/32 = 0.4375
15/32 = 0.46875
16/32 = 0.5
17/32 = 0.53125
18/32 = 0.5625
19/32 = 0.59375
20/32 = 0.625
21/32 = 0.65625
22/32 = 0.6875
23/32 = 0.71875
24/32 = 0.75
25/32 = 0.78125
26/32 = 0.8125
27/32 = 0.84375
28/32 = 0.875
29/32 = 0.90625
30/32 = 0.9375
31/32 = 0.96875
Use the following formula to calculate the ESCI baud rate:
Frequency of the SCI clock source
Baud rate =
64 x BPD x BD x (PD + PDFA)
where:
Frequency of the SCI clock source = fBus or CGMXCLK (selected by
SCIBDSRC in the CONFIG2 register)
BPD = Baud rate register prescaler divisor
BD = Baud rate divisor
PD = Prescaler divisor
PDFA = Prescaler divisor fine adjust
Table 14-11 shows the ESCI baud rates that can be generated with a 4.9152-MHz
bus frequency.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
235
MOTOROLA
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Table 14-11. ESCI Baud Rate Selection Examples
Prescaler
Divisor
(BPD)
Baud Rate
Divisor
(BD)
Baud Rate
(fBus= 4.9152 MHz)
PDS[2:1:0]
PSSB[4:3:2:1:0]
SCP[1:0]
SCR[2:1:0]
0 0 0
1 1 1
1 1 1
1 1 1
1 1 1
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
X X X X X
0 0 0 0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 1
0 1
0 1
0 1
0 1
0 1
0 1
0 1
1 0
1 0
1 0
1 0
1 0
1 0
1 0
1 0
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1
1
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
1
1
76,800
9600
9562.65
9525.58
8563.07
38,400
19,200
9600
4800
2400
1200
600
0 0 0 0 1
1
1
0 0 0 1 0
1
1
1 1 1 1 1
1
1
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
1
2
1
4
1
8
1
16
32
64
128
1
1
1
1
3
25,600
12,800
6400
3200
1600
800
3
2
3
4
3
8
3
16
32
64
128
1
3
3
400
3
200
4
19,200
9600
4800
2400
1200
600
4
2
4
4
4
8
4
16
32
64
128
1
4
4
300
4
150
13
13
13
13
13
13
13
13
5908
2954
1477
739
2
4
8
16
32
64
128
369
185
92
46
Data Sheet
236
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
ESCI Arbiter
14.9 ESCI Arbiter
The ESCI module comprises an arbiter module designed to support software for
communication tasks as bus arbitration, baud rate recovery and break time
detection. The arbiter module consists of an 9-bit counter with 1-bit overflow and
control logic. The CPU can control operation mode via the ESCI arbiter control
register (SCIACTL).
14.9.1 ESCI Arbiter Control Register
Address:
$000A
Bit 7
6
5
AM0
0
4
ACLK
0
3
2
1
Bit 0
Read:
Write:
Reset:
ALOST
AFIN
ARUN
AROVFL
ARD8
AM1
0
0
0
0
0
0
= Unimplemented
Figure 14-19. ESCI Arbiter Control Register (SCIACTL)
AM1 and AM0 — Arbiter Mode Select Bits
These read/write bits select the mode of the arbiter module as shown in
Table 14-12. Reset clears AM1 and AM0.
Table 14-12. ESCI Arbiter Selectable Modes
AM[1:0]
0 0
ESCI Arbiter Mode
Idle / counter reset
0 1
Bit time measurement
Bus arbitration
1 0
1 1
Reserved / do not use
ALOST — Arbitration Lost Flag
This read-only bit indicates loss of arbitration. Clear ALOST by writing a 0 to
AM1. Reset clears ALOST.
ACLK — Arbiter Counter Clock Select Bit
This read/write bit selects the arbiter counter clock source. Reset clears ACLK.
1 = Arbiter counter is clocked with one half of the ESCI input clock generated
by the ESCI prescaler
0 = Arbiter counter is clocked with the bus clock divided by four
NOTE:
For ACLK = 1, the arbiter input clock is driven from the ESCI prescaler. The
prescaler can be clocked by either the bus clock or CGMXCLK depending on the
state of the SCIBDSRC bit in CONFIG2.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Enhanced Serial Communications Interface (ESCI) Module
Data Sheet
237
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
AFIN— Arbiter Bit Time Measurement Finish Flag
This read-only bit indicates bit time measurement has finished. Clear AFIN by
writing any value to SCIACTL. Reset clears AFIN.
1 = Bit time measurement has finished
0 = Bit time measurement not yet finished
ARUN— Arbiter Counter Running Flag
This read-only bit indicates the arbiter counter is running. Reset clears ARUN.
1 = Arbiter counter running
0 = Arbiter counter stopped
AROVFL— Arbiter Counter Overflow Bit
This read-only bit indicates an arbiter counter overflow. Clear AROVFL by
writing any value to SCIACTL. Writing 0s to AM1 and AM0 resets the counter
keeps it in this idle state. Reset clears AROVFL.
1 = Arbiter counter overflow has occurred
0 = No arbiter counter overflow has occurred
ARD8— Arbiter Counter MSB
This read-only bit is the MSB of the 9-bit arbiter counter. Clear ARD8 by writing
any value to SCIACTL. Reset clears ARD8.
14.9.2 ESCI Arbiter Data Register
Address: $000B
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
ARD7
ARD6
ARD5
ARD4
ARD3
ARD2
ARD1
ARD0
0
0
0
0
0
0
0
0
= Unimplemented
Figure 14-20. ESCI Arbiter Data Register (SCIADAT)
ARD7–ARD0 — Arbiter Least Significant Counter Bits
These read-only bits are the eight LSBs of the 9-bit arbiter counter. Clear
ARD7–ARD0 by writing any value to SCIACTL. Writing 0s to AM1 and AM0
permanently resets the counter and keeps it in this idle state. Reset clears
ARD7–ARD0.
Data Sheet
238
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
ESCI Arbiter
14.9.3 Bit Time Measurement
Two bit time measurement modes, described here, are available according to the
state of ACLK.
1. ACLK = 0 — The counter is clocked with one half of the bus clock. The
counter is started when a falling edge on the RxD pin is detected. The
counter will be stopped on the next falling edge. ARUN is set while the
counter is running, AFIN is set on the second falling edge on RxD (for
instance, the counter is stopped). This mode is used to recover the received
baud rate. See Figure 14-21.
2. ACLK = 1 — The counter is clocked with one half of the ESCI input clock
generated by the ESCI prescaler. The counter is started when a 0 is
detected on RxD (see Figure 14-22). A 0 on RxD on enabling the bit time
measurement with ACLK = 1 leads to immediate start of the counter (see
Figure 14-23). The counter will be stopped on the next rising edge of RxD.
This mode is used to measure the length of a received break.
MEASURED TIME
RXD
Figure 14-21. Bit Time Measurement with ACLK = 0
MEASURED TIME
RXD
Figure 14-22. Bit Time Measurement with ACLK = 1, Scenario A
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
239
MOTOROLA
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
MEASURED TIME
RXD
Figure 14-23. Bit Time Measurement with ACLK = 1, Scenario B
14.9.4 Arbitration Mode
If AM[1:0] is set to 10, the arbiter module operates in arbitration mode. On every
rising edge of SCI_TxD (output of the ESCI module, internal chip signal), the
counter is started. When the counter reaches $38 (ACLK = 0) or $08 (ACLK = 1),
RxD is statically sensed. If in this case, RxD is sensed low (for example, another
bus is driving the bus dominant) ALOST is set. As long as ALOST is set, the TxD
pin is forced to 1, resulting in a seized transmission.
If SCI_TxD senses 0 without having sensed a 0 before on RxD, the counter will be
reset, arbitration operation will be restarted after the next rising edge of SCI_TxD.
Data Sheet
240
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Enhanced Serial Communications Interface (ESCI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 15. System Integration Module (SIM)
15.1 Introduction
This section describes the system integration module (SIM). Together with the
central processor unit (CPU), the SIM controls all microcontroller unit (MCU)
activities. A block diagram of the SIM is shown in Figure 15-1. Table 15-1 is a
summary of the SIM input/output (I/O) registers. The SIM is a system state
controller that coordinates CPU and exception timing.
The SIM is responsible for:
•
Bus clock generation and control for CPU and peripherals:
–
–
Stop/wait/reset/break entry and recovery
Internal clock control
•
•
Master reset control, including power-on reset (POR) and computer
operating properly (COP) timeout
Interrupt arbitration
Table 15-1 shows the internal signal names used in this section.
Table 15-1. Signal Name Conventions
Signal Name
CGMXCLK
CGMVCLK
Description
Buffered version of OSC1 from clock generator module (CGM)
PLL output
PLL-based or OSC1-based clock output from CGM module
(Bus clock = CGMOUT divided by two)
CGMOUT
IAB
IDB
Internal address bus
Internal data bus
PORRST
IRST
Signal from the power-on reset module to the SIM
Internal reset signal
R/W
Read/write signal
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
241
MOTOROLA
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
MODULE STOP
MODULE WAIT
CPU STOP (FROM CPU)
CPU WAIT (FROM CPU)
STOP/WAIT
CONTROL
SIMOSCEN (TO CGM)
SIM
COUNTER
CGMXCLK (FROM CGM)
CGMOUT (FROM CGM)
÷ 2
CLOCK
CONTROL
VDD
CLOCK GENERATORS
INTERNAL CLOCKS
INTERNAL
PULLUP
DEVICE
FORCED MONITOR MODE ENTRY
LVI (FROM LVI MODULE)
RESET
PIN LOGIC
POR CONTROL
RESET PIN CONTROL
MASTER
RESET
CONTROL
ILLEGAL OPCODE (FROM CPU)
ILLEGAL ADDRESS (FROM ADDRESS
MAP DECODERS)
SIM RESET STATUS REGISTER
COP (FROM COP MODULE)
RESET
INTERRUPT SOURCES
CPU INTERFACE
INTERRUPT CONTROL
AND PRIORITY DECODE
Figure 15-1. SIM Block Diagram
Data Sheet
242
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
System Integration Module (SIM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Introduction
7
Addr.
Register Name
Bit 7
R
6
R
0
5
R
0
4
R
0
3
R
0
2
R
0
1
Bit 0
R
Read:
SBSW
Note(1)
0
Break Status Register
(BSR) Write:
See page 258.
$FE00
Reset:
0
0
1. Writing a 0 clears SBSW.
Read:
SIM Reset Status Register
(SRSR) Write:
POR
PIN
COP
ILOP
ILAD
MODRST
LVI
0
$FE01
$FE03
$FE04
$FE05
$FE06
$FE07
See page 259.
POR:
Read:
1
0
0
0
0
0
0
0
Break Flag Control Register
BCFE
R
R
R
R
R
R
R
(BFCR) Write:
See page 260.
Reset:
Read:
0
IF6
R
IF5
R
IF4
R
IF3
R
IF2
IF1
R
0
R
0
R
Interrupt Status Register 1
(INT1) Write:
R
See page 254.
Reset:
Read:
0
0
0
0
0
0
0
0
IF14
R
IF13
R
IF12
R
IF11
R
IF10
IF9
R
IF8
R
IF7
R
Interrupt Status Register 2
(INT2) Write:
R
See page 254.
Reset:
Read:
0
0
0
0
0
0
0
0
IF22
R
IF32
R
IF20
R
IF19
R
IF18
IF17
R
IF16
R
IF15
R
Interrupt Status Register 3
(INT3) Write:
R
See page 254.
Reset:
Read:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
IF24
R
IF23
R
Interrupt Status Register 4
(INT4) Write:
See page 255.
Reset:
R
R
R
R
R
R
0
0
0
0
0
0
0
0
= Unimplemented
R
= Reserved
Figure 15-2. SIM I/O Register Summary
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
243
MOTOROLA
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
15.2 SIM Bus Clock Control and Generation
The bus clock generator provides system clock signals for the CPU and peripherals
on the MCU. The system clocks are generated from an incoming clock, CGMOUT,
as shown in Figure 15-3. This clock originates from either an external oscillator or
from the on-chip PLL.
15.2.1 Bus Timing
In user mode, the internal bus frequency is either the crystal oscillator output
(CGMXCLK) divided by four or the PLL output (CGMVCLK) divided by four.
15.2.2 Clock Startup from POR or LVI Reset
When the power-on reset module or the low-voltage inhibit module generates a
reset, the clocks to the CPU and peripherals are inactive and held in an inactive
phase until after the 4096 CGMXCLK cycle POR timeout has completed. The RST
pin is driven low by the SIM during this entire period. The bus clocks start upon
completion of the timeout.
15.2.3 Clocks in Stop Mode and Wait Mode
Upon exit from stop mode by an interrupt or reset, the SIM allows CGMXCLK to
clock the SIM counter. The CPU and peripheral clocks do not become active until
after the stop delay timeout. This timeout is selectable as 4096 or 32 CGMXCLK
cycles. See 15.6.2 Stop Mode.
OSC2
OSC1
OSCILLATOR (OSC)
CGMXCLK
TO TBM,TIM1,TIM2, ADC, MSCAN
SIM
SIMOSCEN
OSCENINSTOP
FROM
CONFIG
SIM COUNTER
IT12
TO REST
OF CHIP
CGMRCLK
CGMOUT
BUS CLOCK
GENERATORS
IT23
TO REST
OF CHIP
÷ 2
PHASE-LOCKED LOOP (PLL)
TO MSCAN
Figure 15-3. System Clock Signals
Data Sheet
244
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
System Integration Module (SIM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Reset and System Initialization
In wait mode, the CPU clocks are inactive. The SIM also produces two sets of
clocks for other modules. Refer to the wait mode subsection of each module to see
if the module is active or inactive in wait mode. Some modules can be programmed
to be active in wait mode.
15.3 Reset and System Initialization
The MCU has these reset sources:
•
•
•
•
•
•
•
Power-on reset module (POR)
External reset pin (RST)
Computer operating properly module (COP)
Low-voltage inhibit module (LVI)
Illegal opcode
Illegal address
Forced monitor mode entry reset (MODRST)
All of these resets produce the vector $FFFE:$FFFF ($FEFE:$FEFF in monitor
mode) and assert the internal reset signal (IRST). IRST causes all registers to be
returned to their default values and all modules to be returned to their reset states.
An internal reset clears the SIM counter (see 15.4 SIM Counter), but an external
reset does not. Each of the resets sets a corresponding bit in the SIM reset status
register (SRSR). See 15.7 SIM Registers.
A reset immediately stops the operation of the instruction being executed. Reset
initializes certain control and status bits. Reset selects CGMXCLK divided by four
as the bus clock.
15.3.1 External Pin Reset
The RST pin circuit includes an internal pullup device. Pulling the asynchronous
RST pin low halts all processing. The PIN bit of the SIM reset status register
(SRSR) is set as long as RST is held low for at least the minimum tRL time and no
other reset sources are present. Figure 15-4 shows the relative timing.
CGMOUT
RST
IAB
VECT H VECT L
PC
Figure 15-4. External Reset Timing
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
245
MOTOROLA
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
15.3.2 Active Resets from Internal Sources
All internal reset sources actively pull the RST pin low for 32 CGMXCLK cycles to
allow resetting of external peripherals. The internal reset continues to be asserted
for an additional 32 cycles at which point the reset vector will be fetched. See
Figure 15-5. An internal reset can be caused by an illegal address, illegal opcode,
COP timeout, LVI, or POR. See Figure 15-6.
NOTE:
For LVI or POR resets, the SIM cycles through 4096 CGMXCLK cycles during
which the SIM forces the RST pin low. The internal reset signal then follows the
sequence from the falling edge of RST shown in Figure 15-5.
The COP reset is asynchronous to the bus clock.
The active reset feature allows the part to issue a reset to peripherals and other
chips within a system built around the MCU.
RST PULLED LOW BY MCU
32 CYCLES
RST
32 CYCLES
CGMXCLK
IAB
VECTOR HIGH
Figure 15-5. Internal Reset Timing
ILLEGAL ADDRESS RST
ILLEGAL OPCODE RST
COPRST
INTERNAL RESET
LVI
POR
MODRST
Figure 15-6. Sources of Internal Reset
Table 15-2. Reset Recovery
Reset Recovery Type
POR/LVI
Actual Number of Cycles
4163 (4096 + 64 + 3)
67 (64 + 3)
All others
Data Sheet
246
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
System Integration Module (SIM) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Reset and System Initialization
15.3.2.1 Power-On Reset
When power is first applied to the MCU, the power-on reset module (POR)
generates a pulse to indicate that power-on has occurred. The external reset pin
(RST) is held low while the SIM counter counts out 4096 + 32 CGMXCLK cycles.
Thirty-two CGMXCLK cycles later, the CPU and memories are released from reset
to allow the reset vector sequence to occur.
At power-on, these events occur:
•
•
•
•
A POR pulse is generated.
The internal reset signal is asserted.
The SIM enables CGMOUT.
Internal clocks to the CPU and modules are held inactive for 4096
CGMXCLK cycles to allow stabilization of the oscillator.
•
•
The RST pin is driven low during the oscillator stabilization time.
The POR bit of the SIM reset status register (SRSR) is set.
OSC1
PORRST
4096
CYCLES
32
CYCLES
32
CYCLES
CGMXCLK
CGMOUT
RST
IAB
$FFFE
$FFFF
Figure 15-7. POR Recovery
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA System Integration Module (SIM)
Data Sheet
247
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
15.3.2.2 Computer Operating Properly (COP) Reset
An input to the SIM is reserved for the COP reset signal. The overflow of the COP
counter causes an internal reset and sets the COP bit in the SIM reset status
register (SRSR) if the COPD bit in the CONFIG1 register is cleared. The SIM
actively pulls down the RST pin for all internal reset sources.
The COP module is disabled if the RST pin or the IRQ pin is held at VTST while the
MCU is in monitor mode. During a break state, VTST on the RST pin disables the
COP module.
15.3.2.3 Illegal Opcode Reset
The SIM decodes signals from the CPU to detect illegal instructions. An illegal
instruction sets the ILOP bit in the SIM reset status register (SRSR) and causes a
reset.
If the stop enable bit, STOP, in the CONFIG1 register is 0, the SIM treats the STOP
instruction as an illegal opcode and causes an illegal opcode reset. The SIM
actively pulls down the RST pin for all internal reset sources.
15.3.2.4 Illegal Address Reset
An opcode fetch from an unmapped address generates an illegal address reset.
The SIM verifies that the CPU is fetching an opcode prior to asserting the ILAD bit
in the SIM reset status register (SRSR) and resetting the MCU. A data fetch from
an unmapped address does not generate a reset. The SIM actively pulls down the
RST pin for all internal reset sources.
15.3.2.5 Low-Voltage Inhibit (LVI) Reset
The low-voltage inhibit module (LVI) asserts its output to the SIM when the VDD
voltage falls to the VTRIPF voltage. The LVI bit in the SIM reset status register
(SRSR) is set, and the external reset pin (RST) is asserted if the LVIPWRD and
LVIRSTD bits in the CONFIG1 register are 0. The RST pin will be held low while
the SIM counter counts out 4096 + 32 CGMXCLK cycles after VDD rises above
VTRIPR. Thirty-two CGMXCLK cycles later, the CPU is released from reset to allow
the reset vector sequence to occur. The SIM actively pulls down the RST pin for all
internal reset sources.
15.3.2.6 Monitor Mode Entry Module Reset (MODRST)
The monitor mode entry module reset (MODRST) asserts its output to the SIM
when monitor mode is entered in the condition where the reset vectors are erased
($FF) (see 20.3.1.1 Normal Monitor Mode). When MODRST gets asserted, an
internal reset occurs. The SIM actively pulls down the RST pin for all internal reset
sources.
Data Sheet
248
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
System Integration Module (SIM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
SIM Counter
15.4 SIM Counter
The SIM counter is used by the power-on reset module (POR) and in stop mode
recovery to allow the oscillator time to stabilize before enabling the internal bus
clocks. The SIM counter also serves as a prescaler for the computer operating
properly (COP) module. The SIM counter overflow supplies the clock for the COP
module. The SIM counter is 12 bits long.
15.4.1 SIM Counter During Power-On Reset
The power-on reset module (POR) detects power applied to the MCU. At
power-on, the POR circuit asserts the signal PORRST. Once the SIM is initialized,
it enables the clock generation module (CGM) to drive the bus clock state machine.
15.4.2 SIM Counter During Stop Mode Recovery
The SIM counter also is used for stop mode recovery. The STOP instruction clears
the SIM counter. After an interrupt, break, or reset, the SIM senses the state of the
short stop recovery bit, SSREC, in the CONFIG1 register. If the SSREC bit is a 1,
then the stop recovery is reduced from the normal delay of 4096 CGMXCLK cycles
down to 32 CGMXCLK cycles. This is ideal for applications using crystals with the
OSCENINSTOP bit set. External crystal applications should use the full stop
recovery time, SSREC cleared, with the OSCENINSTOP bit cleared. See 5.2
Functional Description.
15.4.3 SIM Counter and Reset States
External reset has no effect on the SIM counter. See 15.6.2 Stop Mode for details.
The SIM counter is free-running after all reset states. See 15.3.2 Active Resets
from Internal Sources for counter control and internal reset recovery sequences.
15.5 Exception Control
Normal, sequential program execution can be changed in three different ways:
•
Interrupts:
–
–
Maskable hardware CPU interrupts
Non-maskable software interrupt instruction (SWI)
•
•
Reset
Break interrupts
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
249
MOTOROLA
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
15.5.1 Interrupts
At the beginning of an interrupt, the CPU saves the CPU register contents on the
stack and sets the interrupt mask (I bit) to prevent additional interrupts. At the end
of an interrupt, the RTI instruction recovers the CPU register contents from the
stack so that normal processing can resume. Figure 15-8 shows interrupt entry
timing. Figure 15-9 shows interrupt recovery timing.
Interrupts are latched, and arbitration is performed in the SIM at the start of
interrupt processing. The arbitration result is a constant that the CPU uses to
determine which vector to fetch. Once an interrupt is latched by the SIM, no other
interrupt can take precedence, regardless of priority, until the latched interrupt is
serviced (or the I bit is cleared). See Figure 15-10.
15.5.1.1 Hardware Interrupts
A hardware interrupt does not stop the current instruction. Processing of a
hardware interrupt begins after completion of the current instruction. When the
current instruction is complete, the SIM checks all pending hardware interrupts. If
interrupts are not masked (I bit clear in the condition code register) and if the
corresponding interrupt enable bit is set, the SIM proceeds with interrupt
processing; otherwise, the next instruction is fetched and executed.
MODULE
INTERRUPT
I BIT
IAB
DUMMY
SP
SP – 1
SP – 2
SP – 3
SP – 4
VECT H
VECT L START ADDR
IDB
DUMMY PC – 1[7:0] PC – 1[15:8]
X
A
CCR
V DATA H V DATA L OPCODE
R/W
Figure 15-8. Interrupt Entry Timing
MODULE
INTERRUPT
I BIT
IAB
SP – 4
SP – 3
SP – 2
SP – 1
SP
PC
PC + 1
IDB
R/W
CCR
A
X
PC – 1 [7:0] PC – 1 [15:8] OPCODE OPERAND
Figure 15-9. Interrupt Recovery Timing
Data Sheet
250
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
System Integration Module (SIM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Exception Control
FROM RESET
BREAK
INTERRUPT
YES
?
NO
YES
I BIT SET?
NO
YES
YES
IRQ
INTERRUPT
?
NO
CGM
INTERRUPT
?
NO
OTHER
INTERRUPTS
?
YES
NO
STACK CPU REGISTERS
SET I BIT
LOAD PC WITH INTERRUPT VECTOR
FETCH NEXT
INSTRUCTION
SWI
INSTRUCTION
?
YES
YES
NO
RTI
INSTRUCTION
?
UNSTACK CPU REGISTERS
EXECUTE INSTRUCTION
NO
Figure 15-10. Interrupt Processing
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
251
MOTOROLA
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
If more than one interrupt is pending at the end of an instruction execution, the
highest priority interrupt is serviced first. Figure 15-11 demonstrates what happens
when two interrupts are pending. If an interrupt is pending upon exit from the
original interrupt service routine, the pending interrupt is serviced before the LDA
instruction is executed.
CLI
BACKGROUND
ROUTINE
LDA #$FF
INT1
PSHH
INT1 INTERRUPT SERVICE ROUTINE
PULH
RTI
INT2
PSHH
INT2 INTERRUPT SERVICE ROUTINE
PULH
RTI
Figure 15-11. Interrupt Recognition Example
The LDA opcode is prefetched by both the INT1 and INT2 RTI instructions.
However, in the case of the INT1 RTI prefetch, this is a redundant operation.
NOTE:
To maintain compatibility with the M6805 Family, the H register is not pushed on
the stack during interrupt entry. If the interrupt service routine modifies the H
register or uses the indexed addressing mode, software should save the H register
and then restore it prior to exiting the routine.
15.5.1.2 SWI Instruction
The SWI instruction is a non-maskable instruction that causes an interrupt
regardless of the state of the interrupt mask (I bit) in the condition code register.
NOTE:
A software interrupt pushes PC onto the stack. A software interrupt does not push
PC – 1, as a hardware interrupt does.
15.5.1.3 Interrupt Status Registers
The flags in the interrupt status registers identify maskable interrupt sources.
Table 15-3 summarizes the interrupt sources, hardware flag bits, hardware
interrupt mask bits, interrupt status register flags, interrupt priority, and exception
vectors. The interrupt status registers can be useful for debugging.
Data Sheet
252
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
System Integration Module (SIM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Exception Control
Table 15-3. Interrupt Sources
INT Register
Vector
Address
Mask(1)
Priority(2)
Source
Flag
Flag
Reset
None
None
IRQF
None
None
None
0
0
1
$FFFE–$FFFF
$FFFC–$FFFD
SWI instruction
IRQ pin
None
IF1
IMASK1
$FFFA–$FFFB
$FFF8–$FFF9
$FFF6–$FFF7
$FFF4–$FFF5
$FFF2–$FFF3
$FFF0–$FFF1
$FFEE–$FFEF
$FFEC–$FFED
CGM change in lock
TIM1 channel 0
PLLF
CH0F
CH1F
TOF
PLLIE
CH0IE
CH1IE
TOIE
IF2
IF3
IF4
IF5
IF6
IF7
IF8
2
3
4
5
6
7
8
TIM1 channel 1
TIM1 overflow
TIM2 channel 0
CH0F
CH1F
TOF
CH0IE
CH1IE
TOIE
TIM2 channel 1
TIM2 overflow
SPI receiver full
SPI overflow
SPRF
OVRF
MODF
SPTE
OR
SPRIE
ERRIE
ERRIE
SPTIE
ORIE
IF9
9
$FFEA–$FFEB
$FFE8–$FFE9
SPI mode fault
SPI transmitter empty
SCI receiver overrun
SCI noise flag
IF10
10
NF
NEIE
IF11
11
$FFE6–$FFE7
SCI framing error
SCI parity error
FE
FEIE
PE
PEIE
SCI receiver full
SCI input idle
SCRF
IDLE
SCTE
TC
SCRIE
ILIE
IF12
IF13
12
13
$FFE4–$FFE5
$FFE2–$FFE3
SCI transmitter empty
SCI transmission complete
Keyboard pin
SCTIE
TCIE
KEYF
COCO
TBIF
WUPIF
IMASKK
AIEN
IF14
IF15
IF16
IF17
14
15
16
17
$FFE0–$FFE1
$FFDE–$FFDF
$FFDC–$FFDD
$FFDA–$FFDB
ADC conversion complete
Timebase
TBIE
MSCAN08 receiver wakeup
WUPIE
RWRNIF
TWRNIF
RERIF
TERRIF
BOFFIF
OVRIF
RWRNIE
TWRNIE
RERRIE
TERRIE
BOFFIE
OVRIE
MSCAN08 error
IF18
18
$FFD8–$FFD9
MSCAN08 receiver
RXF
RXFIE
IF19
IF20
19
20
$FFD6–$FFD7
$FFD4–$FFD5
TXE2
TXE1
TXE0
TXEIE2
TXEIE1
TXEIE0
MSCAN08 transmitter
TIM2 channel 2
TIM2 channel 3
TIM2 channel 4
TIM2 channel 5
CH2F
CH3F
CH4F
CH5F
CH2IE
CH3IE
CH4IE
CH5IE
IF21
IF22
IF23
IF24
21
22
23
24
$FFD2–FFD3
$FFD0–FFD1
$FFCE–FFCF
$FFCC–FFCD
1. The I bit in the condition code register is a global mask for all interrupt sources except the SWI instruction.
2. 0 = highest priority
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
253
MOTOROLA
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Interrupt Status
Register 1
Address:
$FE04
Bit 7
IF6
R
6
5
IF4
R
4
IF3
R
3
IF2
R
2
IF1
R
1
0
Bit 0
0
Read:
Write:
Reset:
IF5
R
R
0
R
0
0
0
0
0
0
0
R
= Reserved
Figure 15-12. Interrupt Status Register 1 (INT1)
IF6–IF1 — Interrupt Flags 1–6
These flags indicate the presence of interrupt requests from the sources shown
in Table 15-3.
1 = Interrupt request present
0 = No interrupt request present
Bit 0 and Bit 1 — Always read 0
Interrupt Status
Register 2
Address:
$FE05
Bit 7
IF14
R
6
5
IF12
R
4
IF11
R
3
IF10
R
2
IF9
R
1
IF8
R
Bit 0
IF7
R
Read:
Write:
Reset:
IF13
R
0
0
0
0
0
0
0
0
R
= Reserved
Figure 15-13. Interrupt Status Register 2 (INT2)
IF14–IF7 — Interrupt Flags 14–7
These flags indicate the presence of interrupt requests from the sources shown
in Table 15-3.
1 = Interrupt request present
0 = No interrupt request present
Interrupt Status
Register 3
Address:
$FE06
Bit 7
IF22
R
6
5
IF20
R
4
IF19
R
3
IF18
R
2
IF17
R
1
IF16
R
Bit 0
IF15
R
Read:
Write:
Reset:
IF21
R
0
0
0
0
0
0
0
0
R
= Reserved
Figure 15-14. Interrupt Status Register 3 (INT3)
IF22–IF15 — Interrupt Flags 22–15
These flags indicate the presence of an interrupt request from the source shown
in Table 15-3.
1 = Interrupt request present
0 = No interrupt request present
Data Sheet
254
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
System Integration Module (SIM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Exception Control
Interrupt Status
Register 4
Address:
$FE07
Bit 7
0
6
5
0
4
0
3
0
2
0
1
IF24
R
Bit 0
IF23
R
Read:
Write:
Reset:
0
R
R
R
0
R
0
R
0
R
0
0
0
0
0
R
= Reserved
Figure 15-15. Interrupt Status Register 4 (INT4)
Bits 7–2 — Always read 0
IF24–IF23 — Interrupt Flags 24–23
These flags indicate the presence of an interrupt request from the source shown
in Table 15-3.
1 = Interrupt request present
0 = No interrupt request present
15.5.2 Reset
All reset sources always have equal and highest priority and cannot be arbitrated.
15.5.3 Break Interrupts
The break module can stop normal program flow at a software-programmable
break point by asserting its break interrupt output (see Section 18. Timer
Interface Module (TIM1) and Section 19. Timer Interface Module (TIM2)). The
SIM puts the CPU into the break state by forcing it to the SWI vector location. Refer
to the break interrupt subsection of each module to see how each module is
affected by the break state.
15.5.4 Status Flag Protection in Break Mode
The SIM controls whether status flags contained in other modules can be cleared
during break mode. The user can select whether flags are protected from being
cleared by properly initializing the break clear flag enable bit (BCFE) in the SIM
break flag control register (BFCR).
Protecting flags in break mode ensures that set flags will not be cleared while in
break mode. This protection allows registers to be freely read and written during
break mode without losing status flag information.
Setting the BCFE bit enables the clearing mechanisms. Once cleared in break
mode, a flag remains cleared even when break mode is exited. Status flags with a
2-step clearing mechanism — for example, a read of one register followed by the
read or write of another — are protected, even when the first step is accomplished
prior to entering break mode. Upon leaving break mode, execution of the second
step will clear the flag as normal.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
255
MOTOROLA
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
15.6 Low-Power Modes
Executing the WAIT or STOP instruction puts the MCU in a low
power-consumption mode for standby situations. The SIM holds the CPU in a
non-clocked state. The operation of each of these modes is described in the
following subsections. Both STOP and WAIT clear the interrupt mask (I) in the
condition code register, allowing interrupts to occur.
15.6.1 Wait Mode
In wait mode, the CPU clocks are inactive while the peripheral clocks continue to
run. Figure 15-16 shows the timing for wait mode entry.
A module that is active during wait mode can wakeup the CPU with an interrupt if
the interrupt is enabled. Stacking for the interrupt begins one cycle after the WAIT
instruction during which the interrupt occurred. In wait mode, the CPU clocks are
inactive. Refer to the wait mode subsection of each module to see if the module is
active or inactive in wait mode. Some modules can be programmed to be active in
wait mode.
Wait mode also can be exited by a reset or break. A break interrupt during wait
mode sets the SIM break stop/wait bit, SBSW, in the SIM break status register
(BSR). If the COP disable bit, COPD, in the CONFIG1 register is 0, then the
computer operating properly module (COP) is enabled and remains active in wait
mode.
IAB
IDB
WAIT ADDR
WAIT ADDR + 1
SAME
SAME
PREVIOUS DATA
NEXT OPCODE
SAME
SAME
R/W
Note: Previous data can be operand data or the WAIT opcode, depending on the
last instruction.
Figure 15-16. Wait Mode Entry Timing
Figure 15-17 and Figure 15-18 show the timing for WAIT recovery.
IAB
IDB
$6E0B
$A6
$6E0C
$00FF
$00FE
$00FD
$00FC
$A6
$A6
$01
$0B
$6E
EXITSTOPWAIT
Note: EXITSTOPWAIT = RST pin, CPU interrupt, or break interrupt
Figure 15-17. Wait Recovery from Interrupt or Break
Data Sheet
256
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
System Integration Module (SIM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Low-Power Modes
32
CYCLES
32
CYCLES
IAB
$6E0B
$A6
RSTVCTH RSTVCTL
IDB $A6
RST
$A6
CGMXCLK
Figure 15-18. Wait Recovery from Internal Reset
15.6.2 Stop Mode
In stop mode, the SIM counter is reset and the system clocks are disabled. An
interrupt request from a module can cause an exit from stop mode. Stacking for
interrupts begins after the selected stop recovery time has elapsed. Reset also
causes an exit from stop mode.
The SIM disables the clock generator module outputs (CGMOUT and CGMXCLK)
in stop mode, stopping the CPU and peripherals. Stop recovery time is selectable
using the SSREC bit in CONFIG1. If SSREC is set, stop recovery is reduced from
the normal delay of 4096 CGMXCLK cycles down to 32. This is ideal for
applications using canned oscillators that do not require long startup times from
stop mode.
NOTE:
NOTE:
External crystal applications should use the full stop recovery time by clearing the
SSREC bit unless OSCENINSTOP bit is set in CONFIG2.
The SIM counter is held in reset from the execution of the STOP instruction
until the beginning of stop recovery. It is then used to time the recovery period.
Figure 15-19 shows stop mode entry timing. Figure 15-20 shows stop mode
recovery time from interrupt.
To minimize stop current, all pins configured as inputs should be driven to a 1 or 0.
CPUSTOP
IAB
IDB
STOP ADDR
STOP ADDR + 1
SAME
SAME
PREVIOUS DATA
NEXT OPCODE
SAME
SAME
R/W
Note: Previous data can be operand data or the STOP opcode, depending on the last instruction.
Figure 15-19. Stop Mode Entry Timing
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
257
MOTOROLA
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
STOP RECOVERY PERIOD
CGMXCLK
INT/BREAK
IAB
STOP + 2
STOP + 2
SP
SP – 1
SP – 2
SP – 3
STOP +1
Figure 15-20. Stop Mode Recovery from Interrupt
15.7 SIM Registers
The SIM has three memory-mapped registers. Table 15-4 shows the mapping of
these registers.
Table 15-4. SIM Registers
Address
$FE00
$FE01
$FE03
Register
BSR
Access Mode
User
SRSR
BFCR
User
User
15.7.1 Break Status Register
The break status register (BSR) contains a flag to indicate that a break caused an
exit from wait mode. This register is only used in emulation mode.
Address:
$FE00
Bit 7
6
5
R
0
4
R
0
3
R
0
2
R
0
1
Bit 0
R
Read:
Write:
Reset:
SBSW
Note(1)
0
R
R
0
0
0
R
= Reserved
1. Writing a 0 clears SBSW.
Figure 15-21. Break Status Register (BSR)
SBSW — SIM Break Stop/Wait
SBSW can be read within the break state SWI routine. The user can modify the
return address on the stack by subtracting one from it.
1 = Wait mode was exited by break interrupt.
0 = Wait mode was not exited by break interrupt.
Data Sheet
258
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
System Integration Module (SIM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
SIM Registers
15.7.2 SIM Reset Status Register
This register contains six flags that show the source of the last reset provided all
previous reset status bits have been cleared. Clear the SIM reset status register by
reading it. A power-on reset sets the POR bit and clears all other bits in the register.
The register is initialized on power up with the POR bit set and all other bits cleared.
During a POR or any other internal reset, the RST pin is pulled low. After the pin is
released, it will be sampled 32 CGMXCLK cycles later. If the pin is not above VIH
at this time, then the PIN bit may be set, in addition to whatever other bits are set.
Address:
$FE01
Bit 7
6
5
4
3
2
1
Bit 0
0
Read:
Write:
Reset:
POR
PIN
COP
ILOP
ILAD
MODRST
LVI
1
0
0
0
0
0
0
0
= Unimplemented
Figure 15-22. SIM Reset Status Register (SRSR)
POR — Power-On Reset Bit
1 = Last reset caused by POR circuit
0 = Read of SRSR
PIN — External Reset Bit
1 = Last reset caused by external reset pin (RST)
0 = POR or read of SRSR
COP — Computer Operating Properly Reset Bit
1 = Last reset caused by COP counter
0 = POR or read of SRSR
ILOP — Illegal Opcode Reset Bit
1 = Last reset caused by an illegal opcode
0 = POR or read of SRSR
ILAD — Illegal Address Reset Bit (opcode fetches only)
1 = Last reset caused by an opcode fetch from an illegal address
0 = POR or read of SRSR
MODRST — Monitor Mode Entry Module Reset Bit
1 = Last reset caused by monitor mode entry when vector locations $FFFE
and $FFFF are $FF after POR while IRQ = VDD
0 = POR or read of SRSR
LVI — Low-Voltage Inhibit Reset Bit
1 = Last reset caused by the LVI circuit
0 = POR or read of SRSR
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
259
MOTOROLA
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
System Integration Module (SIM)
15.7.3 Break Flag Control Register
The break flag control register contains a bit that enables software to clear status
bits while the MCU is in a break state.
Address:
$FE03
Bit 7
6
5
4
3
2
1
Bit 0
R
Read:
Write:
Reset:
BCFE
R
R
R
R
R
R
0
R
= Reserved
Figure 15-23. Break Flag Control Register (BFCR)
BCFE — Break Clear Flag Enable Bit
This read/write bit enables software to clear status bits by accessing status
registers while the MCU is in a break state. To clear status bits during the break
state, the BCFE bit must be set.
1 = Status bits clearable during break
0 = Status bits not clearable during break
Data Sheet
260
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
System Integration Module (SIM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 16. Serial Peripheral Interface (SPI) Module
16.1 Introduction
This section describes the serial peripheral interface (SPI) module, which allows
full-duplex, synchronous, serial communications with peripheral devices.
The text that follows describes the SPI. The SPI I/O pin names are SS (slave
select), SPSCK (SPI serial clock), MOSI (master out slave in), and MISO (master
in/slave out). The SPI shares four I/O pins with four parallel I/O ports.
16.2 Features
Features of the SPI module include:
•
•
•
•
•
•
•
Full-duplex operation
Master and slave modes
Double-buffered operation with separate transmit and receive registers
Four master mode frequencies (maximum = bus frequency ÷ 2)
Maximum slave mode frequency = bus frequency
Serial clock with programmable polarity and phase
Two separately enabled interrupts:
–
–
SPRF (SPI receiver full)
SPTE (SPI transmitter empty)
•
•
•
•
Mode fault error flag with CPU interrupt capability
Overflow error flag with CPU interrupt capability
Programmable wired-OR mode
I/O (input/output) port bit(s) software configurable with pullup device(s)
if configured as input port bit(s)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Serial Peripheral Interface (SPI) Module
Data Sheet
261
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
P O R T B
R B D D
P O R T F
D D R F
P O R T G
D D R G
P O R T A
D D R A
P O R T C
R C D D
P O R T E
D D R E
D
P O R T
D D R D
Data Sheet
262
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Functional Description
16.3 Functional Description
The SPI module allows full-duplex, synchronous, serial communication between
the MCU and peripheral devices, including other MCUs. Software can poll the SPI
status flags or SPI operation can be interrupt driven.
If a port bit is configured for input, then an internal pullup device may be enabled
for that port bit.
The following paragraphs describe the operation of the SPI module. Refer to
Figure 16-3 for a summary of the SPI I/O registers.
INTERNAL BUS
TRANSMIT DATA REGISTER
SHIFT REGISTER
BUSCLK
MISO
MOSI
7
6
5
4
3
2
1
0
÷ 2
÷ 8
CLOCK
DIVIDER
RECEIVE DATA REGISTER
÷ 32
÷ 128
PIN
CONTROL
LOGIC
CLOCK
SELECT
SPSCK
SS
SPMSTR
SPE
M
S
CLOCK
LOGIC
SPR1
SPR0
SPMSTR
CPHA
CPOL
TRANSMITTER CPU INTERRUPT REQUEST
RECEIVER/ERROR CPU INTERRUPT REQUEST
MODFEN
ERRIE
SPTIE
SPRIE
SPE
SPWOM
SPI
CONTROL
SPRF
SPTE
OVRF
MODF
Figure 16-2. SPI Module Block Diagram
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
263
MOTOROLA
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Addr.
Register Name
Bit 7
6
5
4
3
2
1
SPE
0
Bit 0
SPTIE
0
Read:
SPI Control Register
SPRIE
R
0
SPMSTR
CPOL
CPHA
SPWOM
0
$0010
(SPCR) Write:
See page 279.
Reset:
Read:
0
1
0
1
SPRF
OVRF
MODF
SPTE
SPI Status and Control
ERRIE
MODFEN
SPR1
SPR0
$0011
$0012
Register (SPSCR) Write:
See page 281.
Reset:
0
0
0
0
1
0
0
0
Read:
R7
T7
R6
T6
R5
T5
R4
T4
R3
T3
R2
T2
R1
T1
R0
T0
SPI Data Register
(SPDR) Write:
See page 283.
Reset:
Unaffected by reset
= Unimplemented
= Reserved
R
Figure 16-3. SPI I/O Register Summary
16.3.1 Master Mode
The SPI operates in master mode when the SPI master bit, SPMSTR, is set.
NOTE:
In a multi-SPI system, configure the SPI modules as master or slave before
enabling them. Enable the master SPI before enabling the slave SPI. Disable the
slave SPI before disabling the master SPI. See 16.12.1 SPI Control Register.
Only a master SPI module can initiate transmissions. Software begins the
transmission from a master SPI module by writing to the transmit data register. If
the shift register is empty, the byte immediately transfers to the shift register,
setting the SPI transmitter empty bit, SPTE. The byte begins shifting out on the
MOSI pin under the control of the serial clock. See Figure 16-4.
MASTER MCU
SLAVE MCU
MISO
MOSI
MISO
MOSI
SHIFT REGISTER
SHIFT REGISTER
SPSCK
SS
SPSCK
SS
BAUD RATE
GENERATOR
VDD
Figure 16-4. Full-Duplex Master-Slave Connections
The SPR1 and SPR0 bits control the baud rate generator and determine the speed
of the shift register. (See 16.12.2 SPI Status and Control Register.) Through the
SPSCK pin, the baud rate generator of the master also controls the shift register of
the slave peripheral.
Data Sheet
264
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Functional Description
As the byte shifts out on the MOSI pin of the master, another byte shifts in from the
slave on the master’s MISO pin. The transmission ends when the receiver full bit,
SPRF, becomes set. At the same time that SPRF becomes set, the byte from the
slave transfers to the receive data register. In normal operation, SPRF signals the
end of a transmission. Software clears SPRF by reading the SPI status and control
register with SPRF set and then reading the SPI data register. Writing to the SPI
data register (SPDR) clears SPTE.
16.3.2 Slave Mode
The SPI operates in slave mode when SPMSTR is clear. In slave mode, the
SPSCK pin is the input for the serial clock from the master MCU. Before a data
transmission occurs, the SS pin of the slave SPI must be low. SS must remain low
until the transmission is complete. See 16.6.2 Mode Fault Error.
In a slave SPI module, data enters the shift register under the control of the serial
clock from the master SPI module. After a byte enters the shift register of a slave
SPI, it transfers to the receive data register, and the SPRF bit is set. To prevent an
overflow condition, slave software then must read the receive data register before
another full byte enters the shift register.
The maximum frequency of the SPSCK for an SPI configured as a slave is the bus
clock speed (which is twice as fast as the fastest master SPSCK clock that can be
generated). The frequency of the SPSCK for an SPI configured as a slave does not
have to correspond to any SPI baud rate. The baud rate only controls the speed of
the SPSCK generated by an SPI configured as a master. Therefore, the frequency
of the SPSCK for an SPI configured as a slave can be any frequency less than or
equal to the bus speed.
When the master SPI starts a transmission, the data in the slave shift register
begins shifting out on the MISO pin. The slave can load its shift register with a new
byte for the next transmission by writing to its transmit data register. The slave must
write to its transmit data register at least one bus cycle before the master starts the
next transmission. Otherwise, the byte already in the slave shift register shifts out
on the MISO pin. Data written to the slave shift register during a transmission
remains in a buffer until the end of the transmission.
When the clock phase bit (CPHA) is set, the first edge of SPSCK starts a
transmission. When CPHA is clear, the falling edge of SS starts a transmission.
See 16.4 Transmission Formats.
NOTE:
SPSCK must be in the proper idle state before the slave is enabled to prevent
SPSCK from appearing as a clock edge.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Serial Peripheral Interface (SPI) Module
Data Sheet
265
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
16.4 Transmission Formats
During an SPI transmission, data is simultaneously transmitted (shifted out serially)
and received (shifted in serially). A serial clock synchronizes shifting and sampling
on the two serial data lines. A slave select line allows selection of an individual
slave SPI device; slave devices that are not selected do not interfere with SPI bus
activities. On a master SPI device, the slave select line can optionally be used to
indicate multiple-master bus contention.
16.4.1 Clock Phase and Polarity Controls
Software can select any of four combinations of serial clock (SPSCK) phase and
polarity using two bits in the SPI control register (SPCR). The clock polarity is
specified by the CPOL control bit, which selects an active high or low clock and has
no significant effect on the transmission format.
The clock phase (CPHA) control bit selects one of two fundamentally different
transmission formats. The clock phase and polarity should be identical for the
master SPI device and the communicating slave device. In some cases, the phase
and polarity are changed between transmissions to allow a master device to
communicate with peripheral slaves having different requirements.
NOTE:
Before writing to the CPOL bit or the CPHA bit, disable the SPI by clearing the SPI
enable bit (SPE).
16.4.2 Transmission Format When CPHA = 0
Figure 16-5 shows an SPI transmission in which CPHA = 0. The figure should not
be used as a replacement for data sheet parametric information.
Two waveforms are shown for SPSCK: one for CPOL = 0 and another for
CPOL = 1. The diagram may be interpreted as a master or slave timing diagram
since the serial clock (SPSCK), master in/slave out (MISO), and master out/slave
in (MOSI) pins are directly connected between the master and the slave. The MISO
signal is the output from the slave, and the MOSI signal is the output from the
master. The SS line is the slave select input to the slave. The slave SPI drives its
MISO output only when its slave select input (SS) is low, so that only the selected
slave drives to the master. The SS pin of the master is not shown but is assumed
to be inactive. The SS pin of the master must be high or must be reconfigured as
general-purpose I/O not affecting the SPI. (See 16.6.2 Mode Fault Error.) When
CPHA = 0, the first SPSCK edge is the MSB capture strobe. Therefore, the slave
must begin driving its data before the first SPSCK edge, and a falling edge on the
SS pin is used to start the slave data transmission. The slave’s SS pin must be
toggled back to high and then low again between each byte transmitted as shown
in Figure 16-6.
When CPHA = 0 for a slave, the falling edge of SS indicates the beginning of the
transmission. This causes the SPI to leave its idle state and begin driving the MISO
pin with the MSB of its data. Once the transmission begins, no new data is allowed
Data Sheet
266
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Transmission Formats
into the shift register from the transmit data register. Therefore, the SPI data
register of the slave must be loaded with transmit data before the falling edge of
SS. Any data written after the falling edge is stored in the transmit data register and
transferred to the shift register after the current transmission.
SPSCK CYCLE #
FOR REFERENCE
1
2
3
4
5
6
7
8
SPSCK; CPOL = 0
SPSCK; CPOL =1
MOSI
FROM MASTER
MSB
BIT 6
BIT 6
BIT 5
BIT 5
BIT 4
BIT 4
BIT 3
BIT 3
BIT 2
BIT 2
BIT 1
BIT 1
LSB
LSB
MISO
FROM SLAVE
MSB
SS; TO SLAVE
CAPTURE STROBE
Figure 16-5. Transmission Format (CPHA = 0)
MISO/MOSI
MASTER SS
BYTE 1
BYTE 2
BYTE 3
SLAVE SS
CPHA = 0
SLAVE SS
CPHA = 1
Figure 16-6. CPHA/SS Timing
16.4.3 Transmission Format When CPHA = 1
Figure 16-7 shows an SPI transmission in which CPHA = 1. The figure should not
be used as a replacement for data sheet parametric information. Two waveforms
are shown for SPSCK: one for CPOL = 0 and another for CPOL = 1. The diagram
may be interpreted as a master or slave timing diagram since the serial clock
(SPSCK), master in/slave out (MISO), and master out/slave in (MOSI) pins are
directly connected between the master and the slave. The MISO signal is the
output from the slave, and the MOSI signal is the output from the master. The SS
line is the slave select input to the slave. The slave SPI drives its MISO output only
when its slave select input (SS) is low, so that only the selected slave drives to the
master. The SS pin of the master is not shown but is assumed to be inactive. The
SS pin of the master must be high or must be reconfigured as general-purpose I/O
not affecting the SPI. (See 16.6.2 Mode Fault Error.) When CPHA = 1, the master
begins driving its MOSI pin on the first SPSCK edge. Therefore, the slave uses the
first SPSCK edge as a start transmission signal. The SS pin can remain low
between transmissions. This format may be preferable in systems having only one
master and only one slave driving the MISO data line.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
267
MOTOROLA
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
SPSCK CYCLE #
FOR REFERENCE
1
2
3
4
5
6
7
8
SPSCK; CPOL = 0
SPSCK; CPOL =1
MOSI
FROM MASTER
MSB
MSB
BIT 6
BIT 6
BIT 5
BIT 5
BIT 4
BIT 4
BIT 3
BIT 3
BIT 2
BIT 2
BIT 1
BIT 1
LSB
MISO
FROM SLAVE
LSB
SS; TO SLAVE
CAPTURE STROBE
Figure 16-7. Transmission Format (CPHA = 1)
When CPHA = 1 for a slave, the first edge of the SPSCK indicates the beginning
of the transmission. This causes the SPI to leave its idle state and begin driving the
MISO pin with the MSB of its data. Once the transmission begins, no new data is
allowed into the shift register from the transmit data register. Therefore, the SPI
data register of the slave must be loaded with transmit data before the first edge of
SPSCK. Any data written after the first edge is stored in the transmit data register
and transferred to the shift register after the current transmission.
16.4.4 Transmission Initiation Latency
When the SPI is configured as a master (SPMSTR = 1), writing to the SPDR starts
a transmission. CPHA has no effect on the delay to the start of the transmission,
but it does affect the initial state of the SPSCK signal. When CPHA = 0, the SPSCK
signal remains inactive for the first half of the first SPSCK cycle. When CPHA = 1,
the first SPSCK cycle begins with an edge on the SPSCK line from its inactive to
its active level. The SPI clock rate (selected by SPR1:SPR0) affects the delay from
the write to SPDR and the start of the SPI transmission. (See Figure 16-8.) The
internal SPI clock in the master is a free-running derivative of the internal MCU
clock. To conserve power, it is enabled only when both the SPE and SPMSTR bits
are set. Since the SPI clock is free-running, it is uncertain where the write to the
SPDR occurs relative to the slower SPSCK. This uncertainty causes the variation
in the initiation delay shown in Figure 16-8. This delay is no longer than a single
SPI bit time. That is, the maximum delay is two MCU bus cycles for DIV2, eight
MCU bus cycles for DIV8, 32 MCU bus cycles for DIV32, and 128 MCU bus cycles
for DIV128.
Data Sheet
268
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Transmission Formats
WRITE
TO SPDR
INITIATION DELAY
BUS
CLOCK
MOSI
MSB
BIT 6
BIT 5
SPSCK
CPHA = 1
SPSCK
CPHA = 0
SPSCK CYCLE
NUMBER
1
2
3
INITIATION DELAY FROM WRITE SPDR TO TRANSFER BEGIN
WRITE
TO SPDR
BUS
CLOCK
SPSCK = BUS CLOCK ÷ 2;
2 POSSIBLE START POINTS
EARLIEST
LATEST
WRITE
TO SPDR
BUS
CLOCK
EARLIEST
WRITE
TO SPDR
SPSCK = BUS CLOCK ÷ 8;
8 POSSIBLE START POINTS
LATEST
LATEST
LATEST
BUS
CLOCK
EARLIEST
WRITE
TO SPDR
SPSCK = BUS CLOCK ÷ 32;
32 POSSIBLE START POINTS
BUS
CLOCK
EARLIEST
SPSCK = BUS CLOCK ÷ 128;
128 POSSIBLE START POINTS
Figure 16-8. Transmission Start Delay (Master)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Serial Peripheral Interface (SPI) Module
Data Sheet
269
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
16.5 Queuing Transmission Data
The double-buffered transmit data register allows a data byte to be queued and
transmitted. For an SPI configured as a master, a queued data byte is transmitted
immediately after the previous transmission has completed. The SPI transmitter
empty flag (SPTE) indicates when the transmit data buffer is ready to accept new
data. Write to the transmit data register only when SPTE is high. Figure 16-9
shows the timing associated with doing back-to-back transmissions with the SPI
(SPSCK has CPHA: CPOL = 1:0).
1
3
8
WRITE TO SPDR
SPTE
5
10
2
SPSCK
CPHA:CPOL = 1:0
MOSI
MSB BIT BIT BIT BIT BIT BIT LSB MSB BIT BIT BIT BIT BIT BIT LSB MSB BIT BIT BIT
3
6
BYTE 1
5
4
3
2
1
6
BYTE 2
5
4
2
1
6
BYTE 3
5
4
4
9
SPRF
READ SPSCR
READ SPDR
6
11
7
12
1
2
CPU WRITES BYTE 1 TO SPDR, CLEARING SPTE BIT.
7
8
CPU READS SPDR, CLEARING SPRF BIT.
CPU WRITES BYTE 3 TO SPDR, QUEUEING BYTE
3 AND CLEARING SPTE BIT.
BYTE 1 TRANSFERS FROM TRANSMIT DATA
REGISTER TO SHIFT REGISTER, SETTING SPTE BIT.
9
SECOND INCOMING BYTE TRANSFERS FROM SHIFT
REGISTER TO RECEIVE DATA REGISTER, SETTING
SPRF BIT.
CPU WRITES BYTE 2 TO SPDR, QUEUEING BYTE 2
AND CLEARING SPTE BIT.
3
4
10
FIRST INCOMING BYTE TRANSFERS FROM SHIFT
REGISTER TO RECEIVE DATA REGISTER, SETTING
SPRF BIT.
BYTE 3 TRANSFERS FROM TRANSMIT DATA
REGISTER TO SHIFT REGISTER, SETTING SPTE BIT.
11
12
CPU READS SPSCR WITH SPRF BIT SET.
CPU READS SPDR, CLEARING SPRF BIT.
5
6
BYTE 2 TRANSFERS FROM TRANSMIT DATA
REGISTER TO SHIFT REGISTER, SETTING SPTE BIT.
CPU READS SPSCR WITH SPRF BIT SET.
Figure 16-9. SPRF/SPTE CPU Interrupt Timing
The transmit data buffer allows back-to-back transmissions without the slave
precisely timing its writes between transmissions as in a system with a single data
buffer. Also, if no new data is written to the data buffer, the last value contained in
the shift register is the next data word to be transmitted.
For an idle master or idle slave that has no data loaded into its transmit buffer, the
SPTE is set again no more than two bus cycles after the transmit buffer empties
into the shift register. This allows the user to queue up a 16-bit value to send. For
an already active slave, the load of the shift register cannot occur until the
transmission is completed. This implies that a back-to-back write to the transmit
data register is not possible. SPTE indicates when the next write can occur.
Data Sheet
270
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Error Conditions
16.6 Error Conditions
The following flags signal SPI error conditions:
•
Overflow (OVRF) — Failing to read the SPI data register before the next full
byte enters the shift register sets the OVRF bit. The new byte does not
transfer to the receive data register, and the unread byte still can be read.
OVRF is in the SPI status and control register.
•
Mode fault error (MODF) — The MODF bit indicates that the voltage on the
slave select pin (SS) is inconsistent with the mode of the SPI. MODF is in
the SPI status and control register.
16.6.1 Overflow Error
The overflow flag (OVRF) becomes set if the receive data register still has unread
data from a previous transmission when the capture strobe of bit 1 of the next
transmission occurs. The bit 1 capture strobe occurs in the middle of SPSCK
cycle 7 (see Figure 16-5 and Figure 16-7.) If an overflow occurs, all data received
after the overflow and before the OVRF bit is cleared does not transfer to the
receive data register and does not set the SPI receiver full bit (SPRF). The unread
data that transferred to the receive data register before the overflow occurred can
still be read. Therefore, an overflow error always indicates the loss of data. Clear
the overflow flag by reading the SPI status and control register and then reading
the SPI data register.
OVRF generates a receiver/error CPU interrupt request if the error interrupt enable
bit (ERRIE) is also set. The SPRF, MODF, and OVRF interrupts share the same
CPU interrupt vector (see Figure 16-12.) It is not possible to enable MODF or
OVRF individually to generate a receiver/error CPU interrupt request. However,
leaving MODFEN low prevents MODF from being set.
If the CPU SPRF interrupt is enabled and the OVRF interrupt is not, watch for an
overflow condition. Figure 16-10 shows how it is possible to miss an overflow. The
first part of Figure 16-10 shows how it is possible to read the SPSCR and SPDR
to clear the SPRF without problems. However, as illustrated by the second
transmission example, the OVRF bit can be set in between the time that SPSCR
and SPDR are read.
In this case, an overflow can be missed easily. Since no more SPRF interrupts can
be generated until this OVRF is serviced, it is not obvious that bytes are being lost
as more transmissions are completed. To prevent this, either enable the OVRF
interrupt or do another read of the SPSCR following the read of the SPDR. This
ensures that the OVRF was not set before the SPRF was cleared and that future
transmissions can set the SPRF bit. Figure 16-11 illustrates this process.
Generally, to avoid this second SPSCR read, enable the OVRF to the CPU by
setting the ERRIE bit.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
271
MOTOROLA
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
BYTE 1
BYTE 2
4
BYTE 3
6
BYTE 4
8
1
SPRF
OVRF
READ
SPSCR
2
5
5
READ
SPDR
3
7
1
2
BYTE 1 SETS SPRF BIT.
CPU READS SPSCR WITH SPRF BIT SET
AND OVRF BIT CLEAR.
CPU READS SPSCR WITH SPRF BIT SET
AND OVRF BIT CLEAR.
6
7
BYTE 3 SETS OVRF BIT. BYTE 3 IS LOST.
3
4
CPU READS BYTE 1 IN SPDR,
CLEARING SPRF BIT.
CPU READS BYTE 2 IN SPDR, CLEARING SPRF BIT,
BUT NOT OVRF BIT.
BYTE 2 SETS SPRF BIT.
8
BYTE 4 FAILS TO SET SPRF BIT BECAUSE
OVRF BIT IS NOT CLEARED. BYTE 4 IS LOST.
Figure 16-10. Missed Read of Overflow Condition
BYTE 1
1
BYTE 2
5
BYTE 3
7
BYTE 4
11
SPI RECEIVE
COMPLETE
SPRF
OVRF
READ
SPSCR
2
4
6
9
12
14
READ
SPDR
3
8
10
13
1
2
8
9
BYTE 1 SETS SPRF BIT.
CPU READS BYTE 2 IN SPDR,
CLEARING SPRF BIT.
CPU READS SPSCR WITH SPRF BIT SET
AND OVRF BIT CLEAR.
CPU READS SPSCR AGAIN
TO CHECK OVRF BIT.
3
4
CPU READS BYTE 1 IN SPDR,
CLEARING SPRF BIT.
10
CPU READS BYTE 2 SPDR,
CLEARING OVRF BIT.
CPU READS SPSCR AGAIN
TO CHECK OVRF BIT.
11
12
13
BYTE 4 SETS SPRF BIT.
CPU READS SPSCR.
5
6
BYTE 2 SETS SPRF BIT.
CPU READS SPSCR WITH SPRF BIT SET
AND OVRF BIT CLEAR.
CPU READS BYTE 4 IN SPDR,
CLEARING SPRF BIT.
7
BYTE 3 SETS OVRF BIT. BYTE 3 IS LOST.
14
CPU READS SPSCR AGAIN
TO CHECK OVRF BIT.
Figure 16-11. Clearing SPRF When OVRF Interrupt Is Not Enabled
Data Sheet
272
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Error Conditions
16.6.2 Mode Fault Error
Setting SPMSTR selects master mode and configures the SPSCK and MOSI pins
as outputs and the MISO pin as an input. Clearing SPMSTR selects slave mode
and configures the SPSCK and MOSI pins as inputs and the MISO pin as an
output. The mode fault bit, MODF, becomes set any time the state of the slave
select pin, SS, is inconsistent with the mode selected by SPMSTR.
To prevent SPI pin contention and damage to the MCU, a mode fault error occurs if:
•
•
The SS pin of a slave SPI goes high during a transmission
The SS pin of a master SPI goes low at any time
For the MODF flag to be set, the mode fault error enable bit (MODFEN) must be
set. Clearing the MODFEN bit does not clear the MODF flag but does prevent
MODF from being set again after MODF is cleared.
MODF generates a receiver/error CPU interrupt request if the error interrupt enable
bit (ERRIE) is also set. The SPRF, MODF, and OVRF interrupts share the same
CPU interrupt vector. (See Figure 16-12.) It is not possible to enable MODF or
OVRF individually to generate a receiver/error CPU interrupt request. However,
leaving MODFEN low prevents MODF from being set.
In a master SPI with the mode fault enable bit (MODFEN) set, the mode fault flag
(MODF) is set if SS goes low. A mode fault in a master SPI causes the following
events to occur:
•
•
•
•
•
If ERRIE = 1, the SPI generates an SPI receiver/error CPU interrupt request.
The SPE bit is cleared.
The SPTE bit is set.
The SPI state counter is cleared.
The data direction register of the shared I/O port regains control of port
drivers.
NOTE:
To prevent bus contention with another master SPI after a mode fault error, clear
all SPI bits of the data direction register of the shared I/O port before enabling the
SPI.
When configured as a slave (SPMSTR = 0), the MODF flag is set if SS goes high
during a transmission. When CPHA = 0, a transmission begins when SS goes low
and ends once the incoming SPSCK goes back to its idle level following the shift
of the eighth data bit. When CPHA = 1, the transmission begins when the SPSCK
leaves its idle level and SS is already low. The transmission continues until the
SPSCK returns to its idle level following the shift of the last data bit. See
16.4 Transmission Formats.
NOTE:
Setting the MODF flag does not clear the SPMSTR bit. SPMSTR has no function
when SPE = 0. Reading SPMSTR when MODF = 1 shows the difference between
a MODF occurring when the SPI is a master and when it is a slave.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Serial Peripheral Interface (SPI) Module
Data Sheet
273
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
NOTE:
When CPHA = 0, a MODF occurs if a slave is selected (SS is low) and later
unselected (SS is high) even if no SPSCK is sent to that slave. This happens
because SS low indicates the start of the transmission (MISO driven out with the
value of MSB) for CPHA = 0. When CPHA = 1, a slave can be selected and then
later unselected with no transmission occurring. Therefore, MODF does not occur
since a transmission was never begun.
In a slave SPI (MSTR = 0), MODF generates an SPI receiver/error CPU interrupt
request if the ERRIE bit is set. The MODF bit does not clear the SPE bit or reset
the SPI in any way. Software can abort the SPI transmission by clearing the SPE
bit of the slave.
NOTE:
A high on the SS pin of a slave SPI puts the MISO pin in a high impedance state.
Also, the slave SPI ignores all incoming SPSCK clocks, even if it was already in the
middle of a transmission.
To clear the MODF flag, read the SPSCR with the MODF bit set and then write to
the SPCR register. This entire clearing mechanism must occur with no MODF
condition existing or else the flag is not cleared.
16.7 Interrupts
Four SPI status flags can be enabled to generate CPU interrupt requests. See
Table 16-1.
Table 16-1. SPI Interrupts
Flag
Request
SPTE
Transmitter empty
SPI transmitter CPU interrupt request
(SPTIE = 1, SPE = 1)
SPRF
Receiver full
SPI receiver CPU interrupt request
(SPRIE = 1)
OVRF
Overflow
SPI receiver/error interrupt request
(ERRIE = 1)
MODF
Mode fault
SPI receiver/error interrupt request
(ERRIE = 1)
Reading the SPI status and control register with SPRF set and then reading the
receive data register clears SPRF. The clearing mechanism for the SPTE flag is
always just a write to the transmit data register.
The SPI transmitter interrupt enable bit (SPTIE) enables the SPTE flag to generate
transmitter CPU interrupt requests, provided that the SPI is enabled (SPE = 1).
The SPI receiver interrupt enable bit (SPRIE) enables SPRF to generate receiver
CPU interrupt requests, regardless of the state of SPE. See Figure 16-12.
Data Sheet
274
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Resetting the SPI
SPTE
SPTIE
SPRF
SPE
SPI TRANSMITTER
CPU INTERRUPT REQUEST
SPRIE
SPI RECEIVER/ERROR
CPU INTERRUPT REQUEST
ERRIE
MODF
OVRF
Figure 16-12. SPI Interrupt Request Generation
The error interrupt enable bit (ERRIE) enables both the MODF and OVRF bits to
generate a receiver/error CPU interrupt request.
The mode fault enable bit (MODFEN) can prevent the MODF flag from being set
so that only the OVRF bit is enabled by the ERRIE bit to generate receiver/error
CPU interrupt requests.
The following sources in the SPI status and control register can generate CPU
interrupt requests:
•
SPI receiver full bit (SPRF) — SPRF becomes set every time a byte
transfers from the shift register to the receive data register. If the SPI
receiver interrupt enable bit, SPRIE, is also set, SPRF generates an SPI
receiver/error CPU interrupt request.
•
SPI transmitter empty (SPTE) — SPTE becomes set every time a byte
transfers from the transmit data register to the shift register. If the SPI
transmit interrupt enable bit, SPTIE, is also set, SPTE generates an SPTE
CPU interrupt request.
16.8 Resetting the SPI
Any system reset completely resets the SPI. Partial resets occur whenever the SPI
enable bit (SPE) is 0. Whenever SPE is 0, the following occurs:
•
•
•
•
The SPTE flag is set.
Any transmission currently in progress is aborted.
The shift register is cleared.
The SPI state counter is cleared, making it ready for a new complete
transmission.
•
All the SPI port logic is defaulted back to being general-purpose I/O.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Serial Peripheral Interface (SPI) Module
Data Sheet
275
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
These items are reset only by a system reset:
•
•
•
All control bits in the SPCR register
All control bits in the SPSCR register (MODFEN, ERRIE, SPR1, and SPR0)
The status flags SPRF, OVRF, and MODF
By not resetting the control bits when SPE is low, the user can clear SPE between
transmissions without having to set all control bits again when SPE is set back high
for the next transmission.
By not resetting the SPRF, OVRF, and MODF flags, the user can still service these
interrupts after the SPI has been disabled. The user can disable the SPI by
writing 0 to the SPE bit. The SPI can also be disabled by a mode fault occurring in
an SPI that was configured as a master with the MODFEN bit set.
16.9 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power-consumption standby
modes.
16.9.1 Wait Mode
The SPI module remains active after the execution of a WAIT instruction. In wait
mode the SPI module registers are not accessible by the CPU. Any enabled CPU
interrupt request from the SPI module can bring the MCU out of wait mode.
If SPI module functions are not required during wait mode, reduce power
consumption by disabling the SPI module before executing the WAIT instruction.
To exit wait mode when an overflow condition occurs, enable the OVRF bit to
generate CPU interrupt requests by setting the error interrupt enable bit (ERRIE).
See 16.7 Interrupts.
16.9.2 Stop Mode
The SPI module is inactive after the execution of a STOP instruction. The STOP
instruction does not affect register conditions. SPI operation resumes after an
external interrupt. If stop mode is exited by reset, any transfer in progress is
aborted, and the SPI is reset.
16.10 SPI During Break Interrupts
The system integration module (SIM) controls whether status bits in other
modules can be cleared during the break state. BCFE in the SIM break flag control
register (SBFCR) enables software to clear status bits during the break state. See
Section 15. System Integration Module (SIM).
Data Sheet
276
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
I/O Signals
To allow software to clear status bits during a break interrupt, write a 1 to BCFE. If
a status bit is cleared during the break state, it remains cleared when the MCU exits
the break state.
To protect status bits during the break state, write a 0 to BCFE. With BCFE at 0 (its
default state), software can read and write I/O registers during the break state
without affecting status bits. Some status bits have a 2-step read/write clearing
procedure. If software does the first step on such a bit before the break, the bit
cannot change during the break state as long as BCFE is 0. After the break, doing
the second step clears the status bit.
Since the SPTE bit cannot be cleared during a break with BCFE cleared, a write to
the transmit data register in break mode does not initiate a transmission nor is this
data transferred into the shift register. Therefore, a write to the SPDR in break
mode with BCFE cleared has no effect.
16.11 I/O Signals
The SPI module has four I/O pins:
•
•
•
•
MISO — Master input/slave output
MOSI — Master output/slave input
SPSCK — Serial clock
SS — Slave select
16.11.1 MISO (Master In/Slave Out)
MISO is one of the two SPI module pins that transmits serial data. In full duplex
operation, the MISO pin of the master SPI module is connected to the MISO pin of
the slave SPI module. The master SPI simultaneously receives data on its MISO
pin and transmits data from its MOSI pin.
Slave output data on the MISO pin is enabled only when the SPI is configured as
a slave. The SPI is configured as a slave when its SPMSTR bit is 0 and its SS pin
is low. To support a multiple-slave system, a high on the SS pin puts the MISO pin
in a high-impedance state.
When enabled, the SPI controls data direction of the MISO pin regardless of the
state of the data direction register of the shared I/O port.
16.11.2 MOSI (Master Out/Slave In)
MOSI is one of the two SPI module pins that transmits serial data. In full-duplex
operation, the MOSI pin of the master SPI module is connected to the MOSI pin of
the slave SPI module. The master SPI simultaneously transmits data from its MOSI
pin and receives data on its MISO pin.
When enabled, the SPI controls data direction of the MOSI pin regardless of the
state of the data direction register of the shared I/O port.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
277
MOTOROLA
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
16.11.3 SPSCK (Serial Clock)
The serial clock synchronizes data transmission between master and slave
devices. In a master MCU, the SPSCK pin is the clock output. In a slave MCU, the
SPSCK pin is the clock input. In full-duplex operation, the master and slave MCUs
exchange a byte of data in eight serial clock cycles.
When enabled, the SPI controls data direction of the SPSCK pin regardless of the
state of the data direction register of the shared I/O port.
16.11.4 SS (Slave Select)
The SS pin has various functions depending on the current state of the SPI. For an
SPI configured as a slave, the SS is used to select a slave. For CPHA = 0, the SS
is used to define the start of a transmission. (See 16.4 Transmission Formats.)
Since it is used to indicate the start of a transmission, SS must be toggled high and
low between each byte transmitted for the CPHA = 0 format. However, it can
remain low between transmissions for the CPHA = 1 format. See Figure 16-13.
When an SPI is configured as a slave, the SS pin is always configured as an input.
It cannot be used as a general-purpose I/O regardless of the state of the MODFEN
control bit. However, the MODFEN bit can still prevent the state of SS from creating
a MODF error. See 16.12.2 SPI Status and Control Register.
MISO/MOSI
MASTER SS
BYTE 1
BYTE 2
BYTE 3
SLAVE SS
CPHA = 0
SLAVE SS
CPHA = 1
Figure 16-13. CPHA/SS Timing
NOTE:
A high on the SS pin of a slave SPI puts the MISO pin in a high-impedance state.
The slave SPI ignores all incoming SPSCK clocks, even if it was already in the
middle of a transmission.
When an SPI is configured as a master, the SS input can be used in conjunction
with the MODF flag to prevent multiple masters from driving MOSI and SPSCK.
(See 16.6.2 Mode Fault Error.) For the state of the SS pin to set the MODF flag,
the MODFEN bit in the SPSCK register must be set. If MODFEN is 0 for an SPI
master, the SS pin can be used as a general-purpose I/O under the control of the
data direction register of the shared I/O port. When MODFEN is 1, SS is an
input-only pin to the SPI regardless of the state of the data direction register of the
shared I/O port.
The CPU can always read the state of the SS pin by configuring the appropriate
pin as an input and reading the port data register. See Table 16-2.
Data Sheet
278
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
I/O Registers
Table 16-2. SPI Configuration
SPE
SPMSTR
MODFEN
SPI Configuration
Not enabled
Function of SS Pin
General-purpose I/O;
SS ignored by SPI
X(1))
0
1
1
1
X
X
0
0
1
1
Slave
Input-only to SPI
General-purpose I/O;
SS ignored by SPI
Master without MODF
Master with MODF
1
Input-only to SPI
1. X = Don’t care
16.12 I/O Registers
Three registers control and monitor SPI operation:
•
•
•
SPI control register (SPCR)
SPI status and control register (SPSCR)
SPI data register (SPDR)
16.12.1 SPI Control Register
The SPI control register:
•
•
•
•
•
Enables SPI module interrupt requests
Configures the SPI module as master or slave
Selects serial clock polarity and phase
Configures the SPSCK, MOSI, and MISO pins as open-drain outputs
Enables the SPI module
Address: $0010
Bit 7
6
5
SPMSTR
1
4
CPOL
0
3
CPHA
1
2
SPWOM
0
1
SPE
0
Bit 0
SPTIE
0
Read:
Write:
Reset:
SPRIE
R
0
0
= Reserved
R
Figure 16-14. SPI Control Register (SPCR)
SPRIE — SPI Receiver Interrupt Enable Bit
This read/write bit enables CPU interrupt requests generated by the SPRF bit.
The SPRF bit is set when a byte transfers from the shift register to the receive
data register. Reset clears the SPRIE bit.
1 = SPRF CPU interrupt requests enabled
0 = SPRF CPU interrupt requests disabled
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
279
MOTOROLA
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
SPMSTR — SPI Master Bit
This read/write bit selects master mode operation or slave mode operation.
Reset sets the SPMSTR bit.
1 = Master mode
0 = Slave mode
CPOL — Clock Polarity Bit
This read/write bit determines the logic state of the SPSCK pin between
transmissions. (See Figure 16-5 and Figure 16-7.) To transmit data between
SPI modules, the SPI modules must have identical CPOL values. Reset clears
the CPOL bit.
CPHA — Clock Phase Bit
This read/write bit controls the timing relationship between the serial clock and
SPI data. (See Figure 16-5 and Figure 16-7.) To transmit data between SPI
modules, the SPI modules must have identical CPHA values. When CPHA = 0,
the SS pin of the slave SPI module must be high between bytes. (See Figure
16-13.) Reset sets the CPHA bit.
SPWOM — SPI Wired-OR Mode Bit
This read/write bit disables the pullup devices on pins SPSCK, MOSI, and MISO
so that those pins become open-drain outputs.
1 = Wired-OR SPSCK, MOSI, and MISO pins
0 = Normal push-pull SPSCK, MOSI, and MISO pins
SPE — SPI Enable
This read/write bit enables the SPI module. Clearing SPE causes a partial reset
of the SPI. (See 16.8 Resetting the SPI.) Reset clears the SPE bit.
1 = SPI module enabled
0 = SPI module disabled
SPTIE— SPI Transmit Interrupt Enable
This read/write bit enables CPU interrupt requests generated by the SPTE bit.
SPTE is set when a byte transfers from the transmit data register to the shift
register. Reset clears the SPTIE bit.
1 = SPTE CPU interrupt requests enabled
0 = SPTE CPU interrupt requests disabled
16.12.2 SPI Status and Control Register
The SPI status and control register contains flags to signal these conditions:
•
•
•
•
Receive data register full
Failure to clear SPRF bit before next byte is received (overflow error)
Inconsistent logic level on SS pin (mode fault error)
Transmit data register empty
Data Sheet
280
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
I/O Registers
The SPI status and control register also contains bits that perform these functions:
•
•
•
Enable error interrupts
Enable mode fault error detection
Select master SPI baud rate
Address: $0011
Bit 7
6
ERRIE
0
5
4
3
2
MODFEN
0
1
SPR1
0
Bit 0
SPR0
0
Read:
Write:
Reset:
SPRF
OVRF
MODF
SPTE
0
0
0
1
= Unimplemented
Figure 16-15. SPI Status and Control Register (SPSCR)
SPRF — SPI Receiver Full Bit
This clearable, read-only flag is set each time a byte transfers from the shift
register to the receive data register. SPRF generates a CPU interrupt request if
the SPRIE bit in the SPI control register is set also.
During an SPRF CPU interrupt, the CPU clears SPRF by reading the SPI status
and control register with SPRF set and then reading the SPI data register.
Reset clears the SPRF bit.
1 = Receive data register full
0 = Receive data register not full
ERRIE — Error Interrupt Enable Bit
This read/write bit enables the MODF and OVRF bits to generate CPU interrupt
requests. Reset clears the ERRIE bit.
1 = MODF and OVRF can generate CPU interrupt requests
0 = MODF and OVRF cannot generate CPU interrupt requests
OVRF — Overflow Bit
This clearable, read-only flag is set if software does not read the byte in the
receive data register before the next full byte enters the shift register. In an
overflow condition, the byte already in the receive data register is unaffected,
and the byte that shifted in last is lost. Clear the OVRF bit by reading the SPI
status and control register with OVRF set and then reading the receive data
register. Reset clears the OVRF bit.
1 = Overflow
0 = No overflow
MODF — Mode Fault Bit
This clearable, read-only flag is set in a slave SPI if the SS pin goes high during
a transmission with MODFEN set. In a master SPI, the MODF flag is set if the
SS pin goes low at any time with the MODFEN bit set. Clear MODF by reading
the SPI status and control register (SPSCR) with MODF set and then writing to
the SPI control register (SPCR). Reset clears the MODF bit.
1 = SS pin at inappropriate logic level
0 = SS pin at appropriate logic level
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
281
MOTOROLA
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
SPTE — SPI Transmitter Empty Bit
This clearable, read-only flag is set each time the transmit data register
transfers a byte into the shift register. SPTE generates an SPTE CPU interrupt
request if SPTIE in the SPI control register is set also.
NOTE:
Do not write to the SPI data register unless SPTE is high.
During an SPTE CPU interrupt, the CPU clears SPTE by writing to the transmit
data register.
Reset sets the SPTE bit.
1 = Transmit data register empty
0 = Transmit data register not empty
MODFEN — Mode Fault Enable Bit
This read/write bit, when set, allows the MODF flag to be set. If the MODF flag
is set, clearing MODFEN does not clear the MODF flag. If the SPI is enabled as
a master and the MODFEN bit is 0, then the SS pin is available as a
general-purpose I/O.
If the MODFEN bit is 1, then the SS pin is not available as a general-purpose
I/O. When the SPI is enabled as a slave, the SS pin is not available as a
general-purpose I/O regardless of the value of MODFEN. See 16.11.4 SS
(Slave Select).
If the MODFEN bit is 0, the level of the SS pin does not affect the operation of
an enabled SPI configured as a master. For an enabled SPI configured as a
slave, having MODFEN low only prevents the MODF flag from being set. It does
not affect any other part of SPI operation. See 16.6.2 Mode Fault Error.
SPR1 and SPR0 — SPI Baud Rate Select Bits
In master mode, these read/write bits select one of four baud rates as shown in
Table 16-3. SPR1 and SPR0 have no effect in slave mode. Reset clears SPR1
and SPR0.
Table 16-3. SPI Master Baud Rate Selection
SPR1 and SPR0
Baud Rate Divisor (BD)
00
01
10
11
2
8
32
128
Use this formula to calculate the SPI baud rate:
BUSCLK
Baud rate =
BD
Data Sheet
282
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
I/O Registers
16.12.3 SPI Data Register
The SPI data register consists of the read-only receive data register and the
write-only transmit data register. Writing to the SPI data register writes data into the
transmit data register. Reading the SPI data register reads data from the receive
data register. The transmit data and receive data registers are separate registers
that can contain different values. See Figure 16-2.
Address: $0012
Bit 7
R7
6
5
4
3
2
1
Bit 0
R0
Read:
Write:
Reset:
R6
T6
R5
T5
R4
T4
R3
T3
R2
T2
R1
T1
T7
T0
Unaffected by reset
Figure 16-16. SPI Data Register (SPDR)
R7–R0/T7–T0 — Receive/Transmit Data Bits
NOTE:
Do not use read-modify-write instructions on the SPI data register since the register
read is not the same as the register written.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Serial Peripheral Interface (SPI) Module
Data Sheet
283
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Data Sheet
284
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Serial Peripheral Interface (SPI) Module MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 17. Timebase Module (TBM)
17.1 Introduction
This section describes the timebase module (TBM). The TBM will generate
periodic interrupts at user selectable rates using a counter clocked by the external
clock source. This TBM version uses 15 divider stages, eight of which are user
selectable. A configuration option bit to select an additional 128 divide of the
external clock source can be selected. See Section 5. Configuration Register
(CONFIG)
17.2 Features
Features of the TBM module include:
•
•
•
External clock or an additional divide-by-128 selected by configuration
option bit as clock source
Software configurable periodic interrupts with divide-by: 8, 16, 32, 64, 128,
2048, 8192, and 32768 taps of the selected clock source
Configurable for operation during stop mode to allow periodic wakeup from
stop
17.3 Functional Description
This module can generate a periodic interrupt by dividing the clock source supplied
from the clock generator module, CGMXCLK.
The counter is initialized to all 0s when TBON bit is cleared. The counter, shown in
Figure 17-1, starts counting when the TBON bit is set. When the counter overflows
at the tap selected by TBR2–TBR0, the TBIF bit gets set. If the TBIE bit is set, an
interrupt request is sent to the CPU. The TBIF flag is cleared by writing a 1 to the
TACK bit. The first time the TBIF flag is set after enabling the timebase module, the
interrupt is generated at approximately half of the overflow period. Subsequent
events occur at the exact period.
The timebase module may remain active after execution of the STOP instruction if
the crystal oscillator has been enabled to operate during stop mode through the
OSCENINSTOP bit in the configuration register. The timebase module can be
used in this mode to generate a periodic wakeup from stop mode.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
285
MOTOROLA
Timebase Module (TBM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timebase Module (TBM)
17.4 Interrupts
The timebase module can periodically interrupt the CPU with a rate defined by the
selected TBMCLK and the select bits TBR2–TBR0. When the timebase counter
chain rolls over, the TBIF flag is set. If the TBIE bit is set, enabling the timebase
interrupt, the counter chain overflow will generate a CPU interrupt request.
NOTE:
Interrupts must be acknowledged by writing a 1 to the TACK bit.
TBMCLKSEL
FROM CONFIG2
TBMCLK
0
CGMXCLK
DIVIDE BY 128
1
PRESCALER
FROM CGM MODULE
TBON
÷ 2
÷ 2
÷ 2 ÷ 2 ÷ 2
÷ 2
÷ 2
TBMINT
÷ 2 ÷ 2 ÷ 2 ÷ 2
÷ 2 ÷ 2
÷ 2 ÷ 2
TBIF
TBIE
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
R
Figure 17-1. Timebase Block Diagram
Data Sheet
286
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timebase Module (TBM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timebase Module (TBM)
TBM Interrupt Rate
17.5 TBM Interrupt Rate
The interrupt rate is determined by the equation:
Divider
fCGMXCLK
tTBMRATE
=
where:
fCGMXCLK = Frequency supplied from the clock generator (CGM) module
Divider = Divider value as determined by TBR2–TBR0 settings and
TBMCLKSEL, see Table 17-1
Table 17-1. Timebase Divider Selection
Divider
TBMCLKSEL
TBR2
TBR1
TBR0
0
32,768
8192
2048
128
64
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
4,194,304
1,048,576
262144
16,384
8192
32
4096
16
2048
8
1024
As an example, a 4.9152 MHz crystal, with the TBMCLKSEL set for divide-by-128
and the TBR2–TBR0 set to {011}, the divider is 16,384 and the interrupt rate
calculates to:
16,384
4.9152 x 106
= 3.33 ms
NOTE:
Do not change TBR2–TBR0 bits while the timebase is enabled (TBON = 1).
17.6 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power- consumption standby
modes.
17.6.1 Wait Mode
The timebase module remains active after execution of the WAIT instruction. In
wait mode the timebase register is not accessible by the CPU.
If the timebase functions are not required during wait mode, reduce the power
consumption by stopping the timebase before executing the WAIT instruction.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
287
MOTOROLA
Timebase Module (TBM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timebase Module (TBM)
17.6.2 Stop Mode
The timebase module may remain active after execution of the STOP instruction if
the oscillator has been enabled to operate during stop mode through the
OSCENINSTOP bit in the configuration register. The timebase module can be
used in this mode to generate a periodic wakeup from stop mode.
If the oscillator has not been enabled to operate in stop mode, the timebase module
will not be active during stop mode. In stop mode, the timebase register is not
accessible by the CPU.
If the timebase functions are not required during stop mode, reduce power
consumption by disabling the timebase module before executing the STOP
instruction.
17.7 Timebase Control Register
The timebase has one register, the timebase control register (TBCR), which is
used to enable the timebase interrupts and set the rate.
Address: $001C
Bit 7
6
TBR2
0
5
TBR1
0
4
TBR0
0
3
2
1
TBON
0
Bit 0
Read:
Write:
Reset:
TBIF
0
TACK
0
TBIE
R
0
0
0
= Unimplemented
R
= Reserved
Figure 17-2. Timebase Control Register (TBCR)
TBIF — Timebase Interrupt Flag
This read-only flag bit is set when the timebase counter has rolled over.
1 = Timebase interrupt pending
0 = Timebase interrupt not pending
TBR2–TBR0 — Timebase Divider Selection Bits
These read/write bits select the tap in the counter to be used for timebase
interrupts as shown in Table 17-1.
NOTE:
Do not change TBR2–TBR0 bits while the timebase is enabled (TBON = 1).
TACK— Timebase Acknowledge Bit
The TACK bit is a write-only bit and always reads as 0. Writing a 1 to this bit
clears TBIF, the timebase interrupt flag bit. Writing a 0 to this bit has no effect.
1 = Clear timebase interrupt flag
0 = No effect
Data Sheet
288
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timebase Module (TBM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timebase Module (TBM)
Timebase Control Register
TBIE — Timebase Interrupt Enabled Bit
This read/write bit enables the timebase interrupt when the TBIF bit becomes
set. Reset clears the TBIE bit.
1 = Timebase interrupt is enabled.
0 = Timebase interrupt is disabled.
TBON — Timebase Enabled Bit
This read/write bit enables the timebase. Timebase may be turned off to reduce
power consumption when its function is not necessary. The counter can be
initialized by clearing and then setting this bit. Reset clears the TBON bit.
1 = Timebase is enabled.
0 = Timebase is disabled and the counter initialized to 0s.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
289
MOTOROLA
Timebase Module (TBM)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timebase Module (TBM)
Data Sheet
290
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timebase Module (TBM)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 18. Timer Interface Module (TIM1)
18.1 Introduction
18.2 Features
This section describes the timer interface module (TIM1). TIM1 is a two-channel
timer that provides a timing reference with input capture, output compare, and
pulse-width-modulation functions. Figure 18-2 is a block diagram of the TIM1.
Features of the TIM1 include the following:
•
Two input capture/output compare channels
–
–
Rising-edge, falling-edge, or any-edge input capture trigger
Set, clear, or toggle output compare action
•
•
Buffered and unbuffered pulse width modulation (PWM) signal generation
Programmable TIM1 clock input with 7-frequency internal bus clock
prescaler selection
•
•
•
Free-running or modulo up-count operation
Toggle any channel pin on overflow
TIM1 counter stop and reset bits
18.3 Functional Description
Figure 18-2 shows the structure of the TIM1. The central component of the TIM1
is the 16-bit TIM1 counter that can operate as a free-running counter or a modulo
up-counter. The TIM1 counter provides the timing reference for the input capture
and output compare functions. The TIM1 counter modulo registers,
T1MODH:T1MODL, control the modulo value of the TIM1 counter. Software can
read the TIM1 counter value at any time without affecting the counting sequence.
The two TIM1 channels are programmable independently as input capture or
output compare channels.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
291
MOTOROLA
Timer Interface Module (TIM1)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
P O R T B
D D R B
P O R T F
D D R F
G T P O R
D D R G
A
P O R T
D D R A
P O R T C
D D R C
P O R T E
D D R E
P O R T D
D D R D
Data Sheet
292
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM1) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Functional Description
PRESCALER SELECT
INTERNAL
BUS CLOCK
PRESCALER
TSTOP
TRST
PS2
PS1
PS0
16-BIT COUNTER
TOF
INTERRUPT
LOGIC
TOIE
16-BIT COMPARATOR
T1MODH:T1MODL
TOV0
ELS0B
ELS0A
PORT
CHANNEL 0
16-BIT COMPARATOR
T1CH0H:T1CH0L
16-BIT LATCH
CH0MAX
PTD4/T1CH0
LOGIC
CH0F
INTERRUPT
LOGIC
CH0IE
MS0A
MS0B
CH1F
TOV1
ELS1B
ELS1A
PORT
PTD5/T1CH1
LOGIC
CHANNEL 1
16-BIT COMPARATOR
T1CH1H:T1CH1L
16-BIT LATCH
CH1MAX
INTERRUPT
LOGIC
CH1IE
MS1A
Figure 18-2. TIM1 Block Diagram
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
293
MOTOROLA
Timer Interface Module (TIM1)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Addr.
Register Name
Bit 7
TOF
0
6
5
4
0
3
2
1
Bit 0
Read:
0
TIM1 Status and Control
TOIE
TSTOP
PS2
PS1
PS0
$0020
Register (T1SC) Write:
See page 301.
Reset:
TRST
0
0
0
1
0
0
0
0
Read:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
TIM1 Counter Register High
$0021
$0022
$0023
$0024
$0025
$0026
$0027
$0028
$0029
$002A
(T1CNTH) Write:
See page 302.
Reset:
Read:
0
0
0
0
0
0
0
0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TIM1 Counter Register Low
(T1CNTL) Write:
See page 302.
Reset:
Read:
0
Bit 15
1
0
Bit 14
1
0
Bit 13
1
0
Bit 12
1
0
Bit 11
1
0
Bit 10
1
0
Bit 9
1
0
TIM1 Counter Modulo Register
Bit 8
High (T1MODH) Write:
See page 303.
Reset:
1
Bit 0
1
Read:
TIM1 Counter Modulo Register
Bit 7
Bit 6
1
Bit 5
1
Bit 4
1
Bit 3
1
Bit 2
1
Bit 1
1
Low (T1MODL) Write:
See page 303.
Reset:
1
CH0F
0
Read:
TIM1 Channel 0 Status and
Control Register (T1SC0) Write:
CH0IE
0
MS0B
0
MS0A
0
ELS0B
0
ELS0A
0
TOV0
0
CH0MAX
0
See page 304.
Reset:
0
Read:
TIM1 Channel 0 Register High
Bit 15
Bit 7
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
(T1CH0H) Write:
See page 307.
Reset:
Indeterminate after reset
Bit 4 Bit 3
Indeterminate after reset
Read:
TIM1 Channel 0 Register Low
Bit 6
Bit 5
0
Bit 2
Bit 1
Bit 0
(T1CH0L) Write:
See page 307.
Reset:
Read:
CH1F
TIM1 Channel 1 Status and
Control Register (T1SC1) Write:
CH1IE
0
MS1A
0
ELS1B
0
ELS1A
0
TOV1
0
CH1MAX
0
0
See page 304.
Reset:
0
0
Read:
TIM1 Channel 1 Register High
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
(T1CH1H) Write:
See page 307.
Reset:
Indeterminate after reset
Bit 4 Bit 3
Indeterminate after reset
Read:
TIM1 Channel 1 Register Low
Bit 7
Bit 6
Bit 5
Bit 2
Bit 1
Bit 0
(T1CH1L) Write:
See page 307.
Reset:
= Unimplemented
Figure 18-3. TIM1 I/O Register Summary
Data Sheet
294
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM1)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Functional Description
18.3.1 TIM1 Counter Prescaler
The TIM1 clock source is one of the seven prescaler outputs. The prescaler
generates seven clock rates from the internal bus clock. The prescaler select bits,
PS[2:0], in the TIM1 status and control register (T1SC) select the TIM1 clock
source.
18.3.2 Input Capture
With the input capture function, the TIM1 can capture the time at which an external
event occurs. When an active edge occurs on the pin of an input capture channel,
the TIM1 latches the contents of the TIM1 counter into the TIM1 channel registers,
T1CHxH:T1CHxL. The polarity of the active edge is programmable. Input captures
can generate TIM1 central processor unit (CPU) interrupt requests.
18.3.3 Output Compare
With the output compare function, the TIM1 can generate a periodic pulse with a
programmable polarity, duration, and frequency. When the counter reaches the
value in the registers of an output compare channel, the TIM1 can set, clear, or
toggle the channel pin. Output compares can generate TIM1 CPU interrupt
requests.
18.3.3.1 Unbuffered Output Compare
Any output compare channel can generate unbuffered output compare pulses as
described in 18.3.3 Output Compare. The pulses are unbuffered because
changing the output compare value requires writing the new value over the old
value currently in the TIM1 channel registers.
An unsynchronized write to the TIM1 channel registers to change an output
compare value could cause incorrect operation for up to two counter overflow
periods. For example, writing a new value before the counter reaches the old value
but after the counter reaches the new value prevents any compare during that
counter overflow period. Also, using a TIM1 overflow interrupt routine to write a
new, smaller output compare value may cause the compare to be missed. The
TIM1 may pass the new value before it is written.
Use the following methods to synchronize unbuffered changes in the output
compare value on channel x:
•
When changing to a smaller value, enable channel x output compare
interrupts and write the new value in the output compare interrupt routine.
The output compare interrupt occurs at the end of the current output
compare pulse. The interrupt routine has until the end of the counter
overflow period to write the new value.
•
When changing to a larger output compare value, enable TIM1 overflow
interrupts and write the new value in the TIM1 overflow interrupt routine. The
TIM1 overflow interrupt occurs at the end of the current counter overflow
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
295
MOTOROLA
Timer Interface Module (TIM1)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
period. Writing a larger value in an output compare interrupt routine (at the
end of the current pulse) could cause two output compares to occur in the
same counter overflow period.
18.3.3.2 Buffered Output Compare
Channels 0 and 1 can be linked to form a buffered output compare channel whose
output appears on the T1CH0 pin. The TIM1 channel registers of the linked pair
alternately control the output.
Setting the MS0B bit in TIM1 channel 0 status and control register (TSC0) links
channel 0 and channel 1. The output compare value in the TIM1 channel 0
registers initially controls the output on the T1CH0 pin. Writing to the TIM1
channel 1 registers enables the TIM1 channel 1 registers to synchronously control
the output after the TIM1 overflows. At each subsequent overflow, the TIM1
channel registers (0 or 1) that control the output are the ones written to last. T1SC0
controls and monitors the buffered output compare function, and TIM1 channel 1
status and control register (T1SC1) is unused. While the MS0B bit is set, the
channel 1 pin, T1CH1, is available as a general-purpose I/O pin.
NOTE:
In buffered output compare operation, do not write new output compare values to
the currently active channel registers. User software should track the currently
active channel to prevent writing a new value to the active channel. Writing to the
active channel registers is the same as generating unbuffered output compares.
18.3.4 Pulse Width Modulation (PWM)
By using the toggle-on-overflow feature with an output compare channel, the TIM1
can generate a PWM signal. The value in the TIM1 counter modulo registers
determines the period of the PWM signal. The channel pin toggles when the
counter reaches the value in the TIM1 counter modulo registers. The time between
overflows is the period of the PWM signal.
As Figure 18-4 shows, the output compare value in the TIM1 channel registers
determines the pulse width of the PWM signal. The time between overflow and
output compare is the pulse width. Program the TIM1 to clear the channel pin on
output compare if the polarity of the PWM pulse is 1 (ELSxA = 0). Program the
TIM1 to set the pin if the polarity of the PWM pulse is 0 (ELSxA = 1).
The value in the TIM1 counter modulo registers and the selected prescaler output
determines the frequency of the PWM output. The frequency of an 8-bit PWM
signal is variable in 256 increments. Writing $00FF (255) to the TIM1 counter
modulo registers produces a PWM period of 256 times the internal bus clock period
if the prescaler select value is 000. See 18.8.1 TIM1 Status and Control Register.
The value in the TIM1 channel registers determines the pulse width of the PWM
output. The pulse width of an 8-bit PWM signal is variable in 256 increments.
Writing $0080 (128) to the TIM1 channel registers produces a duty cycle of
128/256 or 50%.
Data Sheet
296
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM1)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Functional Description
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
POLARITY = 1
(ELSxA = 0)
TCHx
TCHx
PULSE
WIDTH
POLARITY = 0
(ELSxA = 1)
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
Figure 18-4. PWM Period and Pulse Width
18.3.4.1 Unbuffered PWM Signal Generation
Any output compare channel can generate unbuffered PWM pulses as described
in 18.3.4 Pulse Width Modulation (PWM). The pulses are unbuffered because
changing the pulse width requires writing the new pulse width value over the old
value currently in the TIM1 channel registers.
An unsynchronized write to the TIM1 channel registers to change a pulse width
value could cause incorrect operation for up to two PWM periods. For example,
writing a new value before the counter reaches the old value but after the counter
reaches the new value prevents any compare during that PWM period. Also, using
a TIM1 overflow interrupt routine to write a new, smaller pulse width value may
cause the compare to be missed. The TIM1 may pass the new value before it is
written to the timer channel (T1CHxH:T1CHxL) registers.
Use the following methods to synchronize unbuffered changes in the PWM pulse
width on channel x:
•
When changing to a shorter pulse width, enable channel x output compare
interrupts and write the new value in the output compare interrupt routine.
The output compare interrupt occurs at the end of the current pulse. The
interrupt routine has until the end of the PWM period to write the new value.
•
When changing to a longer pulse width, enable TIM1 overflow interrupts and
write the new value in the TIM1 overflow interrupt routine. The TIM1
overflow interrupt occurs at the end of the current PWM period. Writing a
larger value in an output compare interrupt routine (at the end of the current
pulse) could cause two output compares to occur in the same PWM period.
NOTE:
In PWM signal generation, do not program the PWM channel to toggle on output
compare. Toggling on output compare prevents reliable 0% duty cycle generation
and removes the ability of the channel to self-correct in the event of software error
or noise. Toggling on output compare also can cause incorrect PWM signal
generation when changing the PWM pulse width to a new, much larger value.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
297
MOTOROLA
Timer Interface Module (TIM1)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
18.3.4.2 Buffered PWM Signal Generation
Channels 0 and 1 can be linked to form a buffered PWM channel whose output
appears on the T1CH0 pin. The TIM1 channel registers of the linked pair
alternately control the pulse width of the output.
Setting the MS0B bit in TIM1 channel 0 status and control register (T1SC0) links
channel 0 and channel 1. The TIM1 channel 0 registers initially control the pulse
width on the T1CH0 pin. Writing to the TIM1 channel 1 registers enables the TIM1
channel 1 registers to synchronously control the pulse width at the beginning of the
next PWM period. At each subsequent overflow, the TIM1 channel registers
(0 or 1) that control the pulse width are the ones written to last. T1SC0 controls and
monitors the buffered PWM function, and TIM1 channel 1 status and control
register (T1SC1) is unused. While the MS0B bit is set, the channel 1 pin, T1CH1,
is available as a general-purpose I/O pin.
NOTE:
In buffered PWM signal generation, do not write new pulse width values to the
currently active channel registers. User software should track the currently active
channel to prevent writing a new value to the active channel. Writing to the active
channel registers is the same as generating unbuffered PWM signals.
18.3.4.3 PWM Initialization
To ensure correct operation when generating unbuffered or buffered PWM signals,
use the following initialization procedure:
1. In the TIM1 status and control register (T1SC):
a. Stop the TIM1 counter by setting the TIM1 stop bit, TSTOP.
b. Reset the TIM1 counter and prescaler by setting the TIM1 reset bit,
TRST.
2. In the TIM1 counter modulo registers (T1MODH:T1MODL), write the value
for the required PWM period.
3. In the TIM1 channel x registers (T1CHxH:T1CHxL), write the value for the
required pulse width.
4. In TIM1 channel x status and control register (T1SCx):
a. Write 0:1 (for unbuffered output compare or PWM signals) or 1:0 (for
buffered output compare or PWM signals) to the mode select bits,
MSxB:MSxA. See Table 18-2.
b. Write 1 to the toggle-on-overflow bit, TOVx.
c. Write 1:0 (polarity 1 — to clear output on compare) or 1:1 (polarity 0 —
to set output on compare) to the edge/level select bits, ELSxB:ELSxA.
The output action on compare must force the output to the complement
of the pulse width level. See Table 18-2.
NOTE:
In PWM signal generation, do not program the PWM channel to toggle on output
compare. Toggling on output compare prevents reliable 0% duty cycle generation
and removes the ability of the channel to self-correct in the event of software error
Data Sheet
298
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM1)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Interrupts
or noise. Toggling on output compare can also cause incorrect PWM signal
generation when changing the PWM pulse width to a new, much larger value.
5. In the TIM1 status control register (T1SC), clear the TIM1 stop bit, TSTOP.
Setting MS0B links channels 0 and 1 and configures them for buffered PWM
operation. The TIM1 channel 0 registers (TCH0H:TCH0L) initially control the
buffered PWM output. TIM1 status control register 0 (TSCR0) controls and
monitors the PWM signal from the linked channels. MS0B takes priority over
MS0A.
Clearing the toggle-on-overflow bit, TOVx, inhibits output toggles on TIM1
overflows. Subsequent output compares try to force the output to a state it is
already in and have no effect. The result is a 0% duty cycle output.
Setting the channel x maximum duty cycle bit (CHxMAX) and setting the TOVx bit
generates a 100% duty cycle output. See 18.8.4 TIM1 Channel Status and
Control Registers.
18.4 Interrupts
The following TIM1 sources can generate interrupt requests:
•
•
TIM1 overflow flag (TOF) — The TOF bit is set when the TIM1 counter
reaches the modulo value programmed in the TIM1 counter modulo
registers. The TIM1 overflow interrupt enable bit, TOIE, enables TIM1
overflow CPU interrupt requests. TOF and TOIE are in the TIM1 status and
control register.
TIM1 channel flags (CH1F:CH0F) — The CHxF bit is set when an input
capture or output compare occurs on channel x. Channel x TIM CPU
interrupt requests are controlled by the channel x interrupt enable bit,
CHxIE. Channel x TIM CPU interrupt requests are enabled when CHxIE =1.
CHxF and CHxIE are in the TIM1 channel x status and control register.
18.5 Wait Mode
The WAIT instruction puts the MCU in low power-consumption standby mode.
The TIM1 remains active after the execution of a WAIT instruction. In wait mode
the TIM1 registers are not accessible by the CPU. Any enabled CPU interrupt
request from the TIM1 can bring the MCU out of wait mode.
If TIM1 functions are not required during wait mode, reduce power consumption by
stopping the TIM1 before executing the WAIT instruction.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
299
MOTOROLA
Timer Interface Module (TIM1)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
18.6 TIM1 During Break Interrupts
A break interrupt stops the TIM1 counter.
The system integration module (SIM) controls whether status bits in other modules
can be cleared during the break state. The BCFE bit in the break flag control
register (BFCR) enables software to clear status bits during the break state. See
Figure 15-21. Break Status Register (BSR).
To allow software to clear status bits during a break interrupt, write a 1 to the BCFE
bit. If a status bit is cleared during the break state, it remains cleared when the MCU
exits the break state.
To protect status bits during the break state, write a 0 to the BCFE bit. With BCFE
at 0 (its default state), software can read and write I/O registers during the break
state without affecting status bits. Some status bits have a two-step read/write
clearing procedure. If software does the first step on such a bit before the break,
the bit cannot change during the break state as long as BCFE is at 0. After the
break, doing the second step clears the status bit.
18.7 Input/Output Signals
Port D shares two of its pins with the TIM1. The two TIM1 channel I/O pins are
PTD4/T1CH0 and PTD5/T1CH1.
Each channel I/O pin is programmable independently as an input capture pin or an
output compare pin. PTD4/T1CH0 can be configured as a buffered output compare
or buffered PWM pin.
18.8 Input/Output Registers
The following I/O registers control and monitor operation of the TIM:
•
•
•
•
•
TIM1 status and control register (T1SC)
TIM1 counter registers (T1CNTH:T1CNTL)
TIM1 counter modulo registers (T1MODH:T1MODL)
TIM1 channel status and control registers (T1SC0 and T1SC1)
TIM1 channel registers (T1CH0H:T1CH0L and T1CH1H:T1CH1L)
18.8.1 TIM1 Status and Control Register
The TIM1 status and control register (T1SC) does the following:
•
•
•
•
•
Enables TIM1 overflow interrupts
Flags TIM1 overflows
Stops the TIM1 counter
Resets the TIM1 counter
Prescales the TIM1 counter clock
Data Sheet
300
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM1)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Input/Output Registers
Address: $0020
Bit 7
6
TOIE
0
5
TSTOP
1
4
0
3
0
2
PS2
0
1
PS1
0
Bit 0
PS0
0
Read:
Write:
Reset:
TOF
0
0
TRST
0
0
= Unimplemented
Figure 18-5. TIM1 Status and Control Register (T1SC)
TOF — TIM1 Overflow Flag Bit
This read/write flag is set when the TIM1 counter reaches the modulo value
programmed in the TIM1 counter modulo registers. Clear TOF by reading the
TIM1 status and control register when TOF is set and then writing a 0 to TOF. If
another TIM1 overflow occurs before the clearing sequence is complete, then
writing 0 to TOF has no effect. Therefore, a TOF interrupt request cannot be lost
due to inadvertent clearing of TOF. Reset clears the TOF bit. Writing a 1 to TOF
has no effect.
1 = TIM1 counter has reached modulo value
0 = TIM1 counter has not reached modulo value
TOIE — TIM1 Overflow Interrupt Enable Bit
This read/write bit enables TIM1 overflow interrupts when the TOF bit becomes
set. Reset clears the TOIE bit.
1 = TIM1 overflow interrupts enabled
0 = TIM1 overflow interrupts disabled
TSTOP — TIM1 Stop Bit
This read/write bit stops the TIM1 counter. Counting resumes when TSTOP is
cleared. Reset sets the TSTOP bit, stopping the TIM1 counter until software
clears the TSTOP bit.
1 = TIM1 counter stopped
0 = TIM1 counter active
NOTE:
Do not set the TSTOP bit before entering wait mode if the TIM1 is required to exit
wait mode. Also, when the TSTOP bit is set and the timer is configured for input
capture operation, input captures are inhibited until the TSTOP bit is cleared.
TRST — TIM1 Reset Bit
Setting this write-only bit resets the TIM1 counter and the TIM1 prescaler.
Setting TRST has no effect on any other registers. Counting resumes from
$0000. TRST is cleared automatically after the TIM1 counter is reset and always
reads as 0. Reset clears the TRST bit.
1 = Prescaler and TIM1 counter cleared
0 = No effect
NOTE:
Setting the TSTOP and TRST bits simultaneously stops the TIM1 counter at a
value of $0000.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
301
MOTOROLA
Timer Interface Module (TIM1)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
PS[2:0] — Prescaler Select Bits
These read/write bits select one of the seven prescaler outputs as the input to
the TIM1 counter as Table 18-1 shows. Reset clears the PS[2:0] bits.
Table 18-1. Prescaler Selection
PS2
0
PS1
0
PS0
0
TIM1 Clock Source
Internal bus clock ÷ 1
Internal bus clock ÷ 2
Internal bus clock ÷ 4
Internal bus clock ÷ 8
Internal bus clock ÷ 16
Internal bus clock ÷ 32
Internal bus clock ÷ 64
Not available
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
18.8.2 TIM1 Counter Registers
The two read-only TIM1 counter registers contain the high and low bytes of the
value in the TIM1 counter. Reading the high byte (T1CNTH) latches the contents
of the low byte (T1CNTL) into a buffer. Subsequent reads of T1CNTH do not affect
the latched T1CNTL value until T1CNTL is read. Reset clears the TIM1 counter
registers. Setting the TIM1 reset bit (TRST) also clears the TIM1 counter registers.
NOTE:
If you read T1CNTH during a break interrupt, be sure to unlatch T1CNTL by
reading T1CNTL before exiting the break interrupt. Otherwise, T1CNTL retains the
value latched during the break.
$0021
T1CNTH
6
Address:
Bit 7
5
4
3
2
1
Bit 0
Bit 8
Read:
Write:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Reset:
0
0
T1CNTL
6
0
0
0
0
0
0
$0022
Address:
Bit 7
Bit 7
5
4
3
2
1
Bit 0
Bit 0
Read:
Write:
Reset:
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
0
0
0
0
0
0
0
0
= Unimplemented
Figure 18-6. TIM1 Counter Registers (T1CNTH:T1CNTL)
Data Sheet
302
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM1)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Input/Output Registers
18.8.3 TIM1 Counter Modulo Registers
The read/write TIM1 modulo registers contain the modulo value for the TIM1
counter. When the TIM1 counter reaches the modulo value, the overflow flag (TOF)
becomes set, and the TIM1 counter resumes counting from $0000 at the next timer
clock. Writing to the high byte (T1MODH) inhibits the TOF bit and overflow
interrupts until the low byte (T1MODL) is written. Reset sets the TIM1 counter
modulo registers.
Address: $0023
Bit 7
T1MODH
6
5
Bit13
1
4
Bit12
1
3
Bit11
1
2
Bit10
1
1
Bit9
1
Bit 0
Bit8
1
Read:
Write:
Reset:
Bit15
1
Bit14
1
T1MODL
6
Address: $0024
Bit 7
5
Bit5
1
4
Bit4
1
3
Bit3
1
2
Bit2
1
1
Bit1
1
Bit 0
Bit0
1
Read:
Write:
Reset:
Bit7
1
Bit6
1
Figure 18-7. TIM1 Counter Modulo Registers (T1MODH:T1MODL)
NOTE:
Reset the TIM1 counter before writing to the TIM1 counter modulo registers.
18.8.4 TIM1 Channel Status and Control Registers
Each of the TIM1 channel status and control registers does the following:
•
•
•
•
•
Flags input captures and output compares
Enables input capture and output compare interrupts
Selects input capture, output compare, or PWM operation
Selects high, low, or toggling output on output compare
Selects rising edge, falling edge, or any edge as the active input capture
trigger
•
•
•
Selects output toggling on TIM1 overflow
Selects 0% and 100% PWM duty cycle
Selects buffered or unbuffered output compare/PWM operation
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
303
MOTOROLA
Timer Interface Module (TIM1)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Address: $0025
Bit 7
T1SC0
6
5
MS0B
0
4
MS0A
0
3
ELS0B
0
2
ELS0A
0
1
TOV0
0
Bit 0
CH0MAX
0
Read:
Write:
Reset:
CH0F
CH0IE
0
0
0
$0028
T1SC1
6
Address:
Bit 7
CH1F
0
5
0
4
MS1A
0
3
ELS1B
0
2
ELS1A
0
1
TOV1
0
Bit 0
CH1MAX
0
Read:
Write:
Reset:
CH1IE
0
0
0
= Unimplemented
Figure 18-8. TIM1 Channel Status and Control
Registers (T1SC0:T1SC1)
CHxF — Channel x Flag Bit
When channel x is an input capture channel, this read/write bit is set when an
active edge occurs on the channel x pin. When channel x is an output compare
channel, CHxF is set when the value in the TIM1 counter registers matches the
value in the TIM1 channel x registers.
Clear CHxF by reading the TIM1 channel x status and control register with CHxF
set and then writing a 0 to CHxF. If another interrupt request occurs before the
clearing sequence is complete, then writing 0 to CHxF has no effect. Therefore,
an interrupt request cannot be lost due to inadvertent clearing of CHxF.
Reset clears the CHxF bit. Writing a 1 to CHxF has no effect.
1 = Input capture or output compare on channel x
0 = No input capture or output compare on channel x
CHxIE — Channel x Interrupt Enable Bit
This read/write bit enables TIM1 CPU interrupt service requests on channel x.
Reset clears the CHxIE bit.
1 = Channel x CPU interrupt requests enabled
0 = Channel x CPU interrupt requests disabled
MSxB — Mode Select Bit B
This read/write bit selects buffered output compare/PWM operation. MSxB
exists only in the TIM1 channel 0 status and control register.
Setting MS0B disables the channel 1 status and control register and reverts
T1CH1 to general-purpose I/O.
Reset clears the MSxB bit.
1 = Buffered output compare/PWM operation enabled
0 = Buffered output compare/PWM operation disabled
Data Sheet
304
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM1)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Input/Output Registers
MSxA — Mode Select Bit A
When ELSxB:A ≠ 00, this read/write bit selects either input capture operation or
unbuffered output compare/PWM operation. See Table 18-2.
1 = Unbuffered output compare/PWM operation
0 = Input capture operation
When ELSxB:A = 00, this read/write bit selects the initial output level of the
TCHx pin (see Table 18-2). Reset clears the MSxA bit.
1 = Initial output level low
0 = Initial output level high
NOTE:
Before changing a channel function by writing to the MSxB or MSxA bit, set the
TSTOP and TRST bits in the TIM1 status and control register (T1SC).
ELSxB and ELSxA — Edge/Level Select Bits
When channel x is an input capture channel, these read/write bits control the
active edge-sensing logic on channel x.
When channel x is an output compare channel, ELSxB and ELSxA control the
channel x output behavior when an output compare occurs.
When ELSxB and ELSxA are both clear, channel x is not connected to an I/O
port, and pin TCHx is available as a general-purpose I/O pin. Table 18-2 shows
how ELSxB and ELSxA work. Reset clears the ELSxB and ELSxA bits.
Table 18-2. Mode, Edge, and Level Selection
MSxB MSxA
ELSxB
ELSxA
Mode
Configuration
Pin under port control;
initial output level high
X
X
0
1
0
0
Output preset
Pin under port control;
initial output level low
0
0
0
0
0
0
0
1
1
0
Capture on rising edge only
Capture on falling edge only
Input capture
Capture on rising
or falling edge
0
0
1
1
0
0
0
0
1
1
1
1
1
1
1
X
X
X
0
0
1
1
0
1
1
0
1
0
1
1
0
1
Software compare only
Toggle output on compare
Clear output on compare
Set output on compare
Toggle output on compare
Clear output on compare
Set output on compare
Output compare
or PWM
Buffered
output
compare or
buffered PWM
NOTE:
After initially enabling a TIM1 channel register for input capture operation and
selecting the edge sensitivity, clear CHxF to ignore any erroneous edge detection
flags.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
305
MOTOROLA
Timer Interface Module (TIM1)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
TOVx — Toggle-On-Overflow Bit
When channel x is an output compare channel, this read/write bit controls the
behavior of the channel x output when the TIM1 counter overflows. When
channel x is an input capture channel, TOVx has no effect. Reset clears the
TOVx bit.
1 = Channel x pin toggles on TIM1 counter overflow.
0 = Channel x pin does not toggle on TIM1 counter overflow.
NOTE:
NOTE:
When TOVx is set, a TIM1 counter overflow takes precedence over a channel x
output compare if both occur at the same time.
CHxMAX — Channel x Maximum Duty Cycle Bit
When the TOVx bit is at 1, setting the CHxMAX bit forces the duty cycle of
buffered and unbuffered PWM signals to 100%. As Figure 18-9 shows, the
CHxMAX bit takes effect in the cycle after it is set or cleared. The output stays
at the 100% duty cycle level until the cycle after CHxMAX is cleared.
The 100% PWM duty cycle is defined as a continuous high level if the PWM polarity
is 1 and a continuous low level if the PWM polarity is 0. Conversely, a 0% PWM
duty cycle is defined as a continuous low level if the PWM polarity is 1 and a
continuous high level if the PWM polarity is 0.
OVERFLOW
OVERFLOW
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
TCHx
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
CHxMAX
Figure 18-9. CHxMAX Latency
18.8.5 TIM1 Channel Registers
These read/write registers contain the captured TIM1 counter value of the input
capture function or the output compare value of the output compare function. The
state of the TIM1 channel registers after reset is unknown.
In input capture mode (MSxB:MSxA = 0:0), reading the high byte of the TIM1
channel x registers (T1CHxH) inhibits input captures until the low byte (T1CHxL) is
read.
In output compare mode (MSxB:MSxA ≠ 0:0), writing to the high byte of the TIM1
channel x registers (T1CHxH) inhibits output compares until the low byte (T1CHxL)
is written.
Data Sheet
306
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM1)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Input/Output Registers
Address: $0026
T1CH0H
6
Bit 7
5
4
3
2
1
Bit 0
Bit 8
Read:
Write:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Reset:
Indeterminate after reset
$0027
T1CH0L
6
Address:
Bit 7
Bit 7
5
4
3
2
1
Bit 0
Bit 0
Read:
Write:
Reset:
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Indeterminate after reset
$0029
T1CH1H
6
Address:
Bit 7
5
4
3
2
1
Bit 0
Bit 8
Read:
Write:
Reset:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Indeterminate after reset
$02A
T1CH1L
6
Address:
Bit 7
Bit 7
5
4
3
2
1
Bit 0
Bit 0
Read:
Write:
Reset:
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Indeterminate after reset
Figure 18-10. TIM1 Channel Registers (T1CH0H/L:T1CH1H/L)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
307
MOTOROLA
Timer Interface Module (TIM1)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM1)
Data Sheet
308
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM1)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 19. Timer Interface Module (TIM2)
19.1 Introduction
19.2 Features
This section describes the timer interface module (TIM2). The TIM2 is a 6-channel
timer that provides a timing reference with input capture, output compare, and
pulse-width-modulation functions. Figure 19-2 is a block diagram of the TIM2.
Features of the TIM2 include:
•
Six input capture/output compare channels:
–
–
Rising-edge, falling-edge, or any-edge input capture trigger
Set, clear, or toggle output compare action
•
•
Buffered and unbuffered pulse width modulation (PWM) signal generation
Programmable TIM2 clock input
–
–
7-frequency internal bus clock prescaler selection
External TIM2 clock input (4-MHz maximum frequency)
•
•
•
Free-running or modulo up-count operation
Toggle any channel pin on overflow
TIM2 counter stop and reset bits
19.3 Functional Description
Figure 19-2 shows the TIM2 structure. The central component of the TIM2 is the
16-bit TIM2 counter that can operate as a free-running counter or a modulo
up-counter. The TIM2 counter provides the timing reference for the input capture
and output compare functions. The TIM2 counter modulo registers,
T2MODH:T2MODL, control the modulo value of the TIM2 counter. Software can
read the TIM2 counter value at any time without affecting the counting sequence.
The six TIM2 channels are programmable independently as input capture or output
compare channels.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
309
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
P O R T B
D D R B
P O R T F
D D R F
G
P O R T
D D R G
A
P O R T
D D R A
P O R T C
D D R C
P O R T E
D D R E
D T P O R
D D R D
Data Sheet
310
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2) MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
Functional Description
TCLK
PRESCALER
PTD6/T2CH0
PRESCALER SELECT
INTERNAL
BUS CLOCK
TSTOP
TRST
PS2
PS1
PS0
16-BIT COUNTER
INTER-
RUPT
LOGIC
TOF
TOIE
16-BIT COMPARATOR
T2MODH:T2MODL
ELS0B
ELS0A
CHANNEL 0
16-BIT COMPARATOR
T2CH0H:T2CH0L
16-BIT LATCH
TOV0
CH0MAX
PTD6
LOGIC
T2CH0
CH0F
MS0B
INTER-
RUPT
LOGIC
CH0IE
MS0A
ELS1B ELS1A
CHANNEL 1
16-BIT COMPARATOR
T2CH1H:T2CH1L
16-BIT LATCH
TOV1
CH1MAX
PTD7
LOGIC
T2CH1
CH1F
INTER-
RUPT
LOGIC
CH1IE
MS1A
ELS2B ELS2A
CHANNEL 2
16-BIT COMPARATOR
T2CH2H:T2CH2L
16-BIT LATCH
TOV2
CH2MAX
PTF4
LOGIC
T2CH2
CH2F
MS2B
INTER-
RUPT
LOGIC
CH2IE
MS2A
ELS3B ELS3A
CHANNEL 3
16-BIT COMPARATOR
T2CH3H:T2CH3L
16-BIT LATCH
TOV3
CH3MAX
PTF5
LOGIG
T2CH3
CH3F
INTER-
RUPT
LOGIC
CH3IE
MS3A
ELS4B ELS4A
CHANNEL 4
16-BIT COMPARATOR
T2CH4H:T2CH4L
16-BIT LATCH
TOV4
CH4MAX
PTF6
LOGIC
T2CH4
CH4F
MS4B
INTER-
RUPT
LOGIC
CH4IE
MS4A
ELS5B ELS5A
CHANNEL 5
16-BIT COMPARATOR
T2CH5H:T2CH5L
16-BIT LATCH
TOV5
CH5MAX
PTF7
LOGIC
T2CH5
CH5F
INTER-
RUPT
LOGIC
CH5IE
MS5A
Figure 19-2. TIM2 Block Diagram
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
311
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
Addr.
Register Name
Bit 7
TOF
0
6
5
4
0
3
2
1
Bit 0
Read:
0
TIM2 Status and Control
TOIE
TSTOP
PS2
PS1
PS0
$002B
Register (T2SC) Write:
See page 323.
Reset:
TRST
0
0
0
1
0
0
0
9
0
Read:
Bit 15
14
13
12
11
10
Bit 8
TIM2 Counter Register High
$002C
$002D
$002E
$002F
$0030
$0031
$0032
$0033
$0034
$0035
$0456
(T2CNTH) Write:
See page 325.
Reset:
Read:
0
0
6
0
5
0
4
0
3
0
2
0
1
0
Bit 7
Bit 0
TIM2 Counter Register Low
(T2CNTL) Write:
See page 325.
Reset:
Read:
0
Bit 15
1
0
0
13
1
0
12
1
0
0
0
0
TIM2 Modulo Register High
14
11
10
9
Bit 8
(T2MODH) Write:
See page 325.
Reset:
1
1
1
1
1
Bit 0
1
Read:
TIM2 Modulo Register Low
Bit 7
6
1
5
4
3
2
1
(T2MODL) Write:
See page 325.
Reset:
1
1
1
1
ELS0B
0
1
ELS0A
0
1
TOV0
0
Read: CH0F
TIM2 Channel 0 Status and
Control Register (T2SC0) Write:
CH0IE
0
MS0B
0
MS0A
0
CH0MAX
0
0
0
See page 326.
Reset:
Read:
TIM2 Channel 0 Register High
Bit 15
14
13
12
11
10
9
Bit 8
(T2CH0H) Write:
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 0 Register Low
Bit 7
6
5
0
4
3
2
1
Bit 0
(T2CH0L) Write:
See page 330.
Reset:
Indeterminate after reset
Read: CH1F
TIM2 Channel 1 Status and
Control Register (T2SC1) Write:
CH1IE
MS1A
0
ELS1B
ELS1A
TOV1
CH1MAX
0
0
See page 326.
Reset:
0
0
0
0
0
9
0
Read:
TIM2 Channel 1 Register High
Bit 15
14
13
12
11
10
Bit 8
(T2CH1H) Write:
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 1 Register Low
Bit 7
6
5
4
3
2
1
Bit 0
(T2CH1L) Write:
See page 330.
Reset:
Indeterminate after reset
Read: CH2F
TIM2 Channel 2 Status and
Control Register (T2SC2) Write:
CH2IE
0
MS2B
0
MS2A
0
ELS2B
0
ELS2A
0
TOV2
0
CH2MAX
0
0
0
See page 326.
Reset:
= Unimplemented
Figure 19-3. TIM2 I/O Register Summary (Sheet 1 of 2)
Data Sheet
312
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
Functional Description
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Read:
TIM2 Channel 2 Register High
Bit 15
14
13
12
11
10
9
Bit 8
$0457
(T2CH2H) Write:
See page 330.
Reset:
Read:
Indeterminate after reset
TIM2 Channel 2 Register Low
Bit 7
6
5
0
4
3
2
1
Bit 0
$0458
$0459
$045A
$045B
$045C
$045D
$045E
$045F
$0460
$0461
(T2CH2L) Write:
See page 330.
Reset:
Read: CH3F
Indeterminate after reset
TIM2 Channel 3 Status and
Control Register (T2SC3) Write:
CH3IE
MS3A
0
ELS3B
ELS3A
TOV3
CH3MAX
0
0
See page 326.
Reset:
0
0
0
0
0
9
0
Read:
TIM2 Channel 3 Register High
Bit 15
14
13
12
11
10
Bit 8
(T2CH3H) Write:
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 3 Register Low
Bit 7
6
5
4
3
2
1
Bit 0
(T2CH3L) Write:
See page 330.
Reset:
Indeterminate after reset
Read: CH4F
TIM2 Channel 4 Status and
Control Register (T2SC4) Write:
CH4IE
MS4B
0
MS4A
0
ELS4B
ELS4A
TOV4
CH4MAX
0
0
See page 326.
Reset:
0
0
0
0
9
0
Read:
TIM2 Channel 4 Register High
Bit 15
14
13
12
11
10
Bit 8
(T2CH4H) Write:
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 4 Register Low
Bit 7
6
5
0
4
3
2
1
Bit 0
(T2CH4L) Write:
See page 330.
Reset:
Indeterminate after reset
Read: CH5F
TIM2 Channel 5 Status and
Control Register (T2SC5) Write:
CH5IE
MS5A
0
ELS5B
ELS5A
TOV5
CH5MAX
0
0
See page 326.
Reset:
0
0
0
0
0
9
0
Read:
TIM2 Channel 5 Register High
Bit 15
14
13
12
11
10
Bit 8
(T2CH5H) Write:
See page 330.
Reset:
Indeterminate after reset
Read:
TIM2 Channel 5 Register Low
Bit 7
6
5
4
3
2
1
Bit 0
(T2CH5L) Write:
See page 330.
Reset:
Indeterminate after reset
= Unimplemented
Figure 19-3. TIM2 I/O Register Summary (Sheet 2 of 2)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
313
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
19.3.1 TIM2 Counter Prescaler
The TIM2 clock source can be one of the seven prescaler outputs or the TIM2 clock
pin, T2CH0. The prescaler generates seven clock rates from the internal bus clock.
The prescaler select bits, PS[2:0], in the TIM2 status and control register select the
TIM2 clock source.
19.3.2 Input Capture
An input capture function has three basic parts: edge select logic, an input capture
latch, and a 16-bit counter. Two 8-bit registers, which make up the 16-bit input
capture register, are used to latch the value of the free-running counter after the
corresponding input capture edge detector senses a defined transition. The
polarity of the active edge is programmable. The level transition which triggers the
counter transfer is defined by the corresponding input edge bits (ELSxB and
ELSxA in T2SC0 through T2SC5 control registers with x referring to the active
channel number). When an active edge occurs on the pin of an input capture
channel, the TIM2 latches the contents of the TIM2 counter into the TIM2 channel
registers, T2CHxH:T2CHxL. Input captures can generate TIM2 CPU interrupt
requests. Software can determine that an input capture event has occurred by
enabling input capture interrupts or by polling the status flag bit.
The free-running counter contents are transferred to the TIM2 channel registers
(T2CHxH:T2CHxL) (see 19.8.5 TIM2 Channel Registers) on each proper signal
transition regardless of whether the TIM2 channel flag (CH0F–CH5F in
T2SC0–T2SC5 registers) is set or clear. When the status flag is set, a CPU
interrupt is generated if enabled. The value of the count latched or “captured” is the
time of the event. Because this value is stored in the input capture register when
the actual event occurs, user software can respond to this event at a later time and
determine the actual time of the event. However, this must be done prior to another
input capture on the same pin; otherwise, the previous time value will be lost.
By recording the times for successive edges on an incoming signal, software can
determine the period and/or pulse width of the signal. To measure a period, two
successive edges of the same polarity are captured. To measure a pulse width, two
alternate polarity edges are captured. Software should track the overflows at the
16-bit module counter to extend its range.
Another use for the input capture function is to establish a time reference. In this
case, an input capture function is used in conjunction with an output compare
function. For example, to activate an output signal a specified number of clock
cycles after detecting an input event (edge), use the input capture function to
record the time at which the edge occurred. A number corresponding to the desired
delay is added to this captured value and stored to an output compare register (see
19.8.5 TIM2 Channel Registers). Because both input captures and output
compares are referenced to the same 16-bit modulo counter, the delay can be
controlled to the resolution of the counter independent of software latencies.
Data Sheet
314
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
Functional Description
Reset does not affect the contents of the input capture channel (T2CHxH:T2CHxL)
registers.
19.3.3 Output Compare
With the output compare function, the TIM2 can generate a periodic pulse with a
programmable polarity, duration, and frequency. When the counter reaches the
value in the registers of an output compare channel, the TIM2 can set, clear, or
toggle the channel pin. Output compares can generate TIM2 CPU interrupt
requests.
19.3.3.1 Unbuffered Output Compare
Any output compare channel can generate unbuffered output compare pulses as
described in 19.3.3 Output Compare. The pulses are unbuffered because
changing the output compare value requires writing the new value over the old
value currently in the TIM2 channel registers.
An unsynchronized write to the TIM2 channel registers to change an output
compare value could cause incorrect operation for up to two counter overflow
periods. For example, writing a new value before the counter reaches the old value
but after the counter reaches the new value prevents any compare during that
counter overflow period. Also, using a TIM2 overflow interrupt routine to write a
new, smaller output compare value may cause the compare to be missed. The
TIM2 may pass the new value before it is written.
Use the following methods to synchronize unbuffered changes in the output
compare value on channel x:
•
When changing to a smaller value, enable channel x output compare
interrupts and write the new value in the output compare interrupt routine.
The output compare interrupt occurs at the end of the current output
compare pulse. The interrupt routine has until the end of the counter
overflow period to write the new value.
•
When changing to a larger output compare value, enable TIM2 overflow
interrupts and write the new value in the TIM2 overflow interrupt routine. The
TIM2 overflow interrupt occurs at the end of the current counter overflow
period. Writing a larger value in an output compare interrupt routine (at the
end of the current pulse) could cause two output compares to occur in the
same counter overflow period.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
315
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
19.3.3.2 Buffered Output Compare
Channels 0 and 1 can be linked to form a buffered output compare channel whose
output appears on the T2CH0 pin. The TIM2 channel registers of the linked pair
alternately control the output.
Setting the MS0B bit in TIM2 channel 0 status and control register (T2SC0) links
channel 0 and channel 1. The output compare value in the TIM2 channel 0
registers initially controls the output on the T2CH0 pin. Writing to the TIM2
channel 1 registers enables the TIM2 channel 1 registers to synchronously control
the output after the TIM2 overflows. At each subsequent overflow, the TIM2
channel registers (0 or 1) that control the output are the ones written to last. T2SC0
controls and monitors the buffered output compare function, and TIM2 channel 1
status and control register (T2SC1) is unused. While the MS0B bit is set, the
channel 1 pin, T2CH1, is available as a general-purpose I/O pin.
Channels 2 and 3 can be linked to form a buffered output compare channel whose
output appears on the T2CH2 pin. The TIM2 channel registers of the linked pair
alternately control the output.
Setting the MS2B bit in TIM2 channel 2 status and control register (T2SC2) links
channel 2 and channel 3. The output compare value in the TIM2 channel 2
registers initially controls the output on the T2CH2 pin. Writing to the TIM2 channel
3 registers enables the TIM2 channel 3 registers to synchronously control the
output after the TIM2 overflows. At each subsequent overflow, the TIM2 channel
registers (2 or 3) that control the output are the ones written to last. T2SC2 controls
and monitors the buffered output compare function, and TIM2 channel 3 status and
control register (T2SC3) is unused. While the MS2B bit is set, the channel 3 pin,
T2CH3, is available as a general-purpose I/O pin.
Channels 4 and 5 can be linked to form a buffered output compare channel whose
output appears on the T2CH4 pin. The TIM2 channel registers of the linked pair
alternately control the output.
Setting the MS4B bit in TIM2 channel 4 status and control register (T2SC4) links
channel 4 and channel 5. The output compare value in the TIM2 channel 4
registers initially controls the output on the T2CH4 pin. Writing to the TIM2 channel
5 registers enables the TIM2 channel 5 registers to synchronously control the
output after the TIM2 overflows. At each subsequent overflow, the TIM2 channel
registers (4 or 5) that control the output are the ones written to last. T2SC4 controls
and monitors the buffered output compare function, and TIM2 channel 5 status and
control register (T2SC5) is unused. While the MS4B bit is set, the channel 5 pin,
T2CH5, is available as a general-purpose I/O pin.
NOTE:
In buffered output compare operation, do not write new output compare values to
the currently active channel registers. User software should track the currently
active channel to prevent writing a new value to the active channel. Writing to the
active channel registers is the same as generating unbuffered output compares.
Data Sheet
316
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
Functional Description
19.3.4 Pulse Width Modulation (PWM)
By using the toggle-on-overflow feature with an output compare channel, the TIM2
can generate a PWM signal. The value in the TIM2 counter modulo registers
determines the period of the PWM signal. The channel pin toggles when the
counter reaches the value in the TIM2 counter modulo registers. The time between
overflows is the period of the PWM signal.
As Figure 19-4 shows, the output compare value in the TIM2 channel registers
determines the pulse width of the PWM signal. The time between overflow and
output compare is the pulse width. Program the TIM2 to clear the channel pin on
output compare if the polarity of the PWM pulse is 1 (ELSxA = 0). Program the
TIM2 to set the pin if the polarity of the PWM pulse is 0 (ELSxA = 1).
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
POLARITY = 1
(ELSxA = 0)
TCHx
TCHx
PULSE
WIDTH
POLARITY = 0
(ELSxA = 1)
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
Figure 19-4. PWM Period and Pulse Width
The value in the TIM2 counter modulo registers and the selected prescaler output
determines the frequency of the PWM output. The frequency of an 8-bit PWM
signal is variable in 256 increments. Writing $00FF (255) to the TIM2 counter
modulo registers produces a PWM period of 256 times the internal bus clock period
if the prescaler select value is 000 (see 19.8.1 TIM2 Status and Control
Register).
The value in the TIM2 channel registers determines the pulse width of the PWM
output. The pulse width of an 8-bit PWM signal is variable in 256 increments.
Writing $0080 (128) to the TIM2 channel registers produces a duty cycle of
128/256 or 50%.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
317
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
19.3.4.1 Unbuffered PWM Signal Generation
Any output compare channel can generate unbuffered PWM pulses as described
in 19.3.4 Pulse Width Modulation (PWM). The pulses are unbuffered because
changing the pulse width requires writing the new pulse width value over the value
currently in the TIM2 channel registers.
An unsynchronized write to the TIM2 channel registers to change a pulse width
value could cause incorrect operation for up to two PWM periods. For example,
writing a new value before the counter reaches the old value but after the counter
reaches the new value prevents any compare during that PWM period. Also, using
a TIM2 overflow interrupt routine to write a new, smaller pulse width value may
cause the compare to be missed. The TIM2 may pass the new value before it is
written to the timer channel (T2CHxH:T2CHxL) registers.
Use the following methods to synchronize unbuffered changes in the PWM pulse
width on channel x:
•
•
When changing to a shorter pulse width, enable channel x output compare
interrupts and write the new value in the output compare interrupt routine.
The output compare interrupt occurs at the end of the current pulse. The
interrupt routine has until the end of the PWM period to write the new value.
When changing to a longer pulse width, enable TIM2 overflow interrupts and
write the new value in the TIM2 overflow interrupt routine. The TIM2
overflow interrupt occurs at the end of the current PWM period. Writing a
larger value in an output compare interrupt routine (at the end of the current
pulse) could cause two output compares to occur in the same PWM period.
NOTE:
In PWM signal generation, do not program the PWM channel to toggle on output
compare. Toggling on output compare prevents reliable 0% duty cycle generation
and removes the ability of the channel to self-correct in the event of software error
or noise. Toggling on output compare also can cause incorrect PWM signal
generation when changing the PWM pulse width to a new, much larger value.
19.3.4.2 Buffered PWM Signal Generation
Channels 0 and 1 can be linked to form a buffered PWM channel whose output
appears on the T2CH0 pin. The TIM2 channel registers of the linked pair
alternately control the pulse width of the output.
Setting the MS0B bit in TIM2 channel 0 status and control register (T2SC0) links
channel 0 and channel 1. The TIM2 channel 0 registers initially control the pulse
width on the T2CH0 pin. Writing to the TIM2 channel 1 registers enables the TIM2
channel 1 registers to synchronously control the pulse width at the beginning of the
next PWM period. At each subsequent overflow, the TIM2 channel registers
(0 or 1) that control the pulse width are the ones written to last. T2SC0 controls and
monitors the buffered PWM function, and TIM2 channel 1 status and control
register (T2SC1) is unused. While the MS0B bit is set, the channel 1 pin, T2CH1,
is available as a general-purpose I/O pin.
Data Sheet
318
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
Functional Description
Channels 2 and 3 can be linked to form a buffered PWM channel whose output
appears on the T2CH2 pin. The TIM2 channel registers of the linked pair
alternately control the pulse width of the output.
Setting the MS2B bit in TIM2 channel 2 status and control register (T2SC2) links
channel 2 and channel 3. The TIM2 channel 2 registers initially control the pulse
width on the T2CH2 pin. Writing to the TIM2 channel 3 registers enables the TIM2
channel 3 registers to synchronously control the pulse width at the beginning of the
next PWM period. At each subsequent overflow, the TIM2 channel registers
(2 or 3) that control the pulse width are the ones written to last. T2SC2 controls and
monitors the buffered PWM function, and TIM2 channel 3 status and control
register (T2SC3) is unused. While the MS2B bit is set, the channel 3 pin, T2CH3,
is available as a general-purpose I/O pin.
Channels 4 and 5 can be linked to form a buffered PWM channel whose output
appears on the T2CH4 pin. The TIM2 channel registers of the linked pair
alternately control the pulse width of the output.
Setting the MS4B bit in TIM2 channel 4 status and control register (T2SC4) links
channel 4 and channel 5. The TIM2 channel 4 registers initially control the pulse
width on the T2CH4 pin. Writing to the TIM2 channel 5 registers enables the TIM2
channel 5 registers to synchronously control the pulse width at the beginning of the
next PWM period. At each subsequent overflow, the TIM2 channel registers
(4 or 5) that control the pulse width are the ones written to last. T2SC4 controls and
monitors the buffered PWM function, and TIM2 channel 5 status and control
register (T2SC5) is unused. While the MS4B bit is set, the channel 5 pin, T2CH5,
is available as a general-purpose I/O pin.
NOTE:
In buffered PWM signal generation, do not write pulse width values to the currently
active channel registers. User software should track the currently active channel to
prevent writing a new value to the active channel. Writing to the active channel
registers is the same as generating unbuffered PWM signals.
19.3.4.3 PWM Initialization
To ensure correct operation when generating unbuffered or buffered PWM signals,
use the following initialization procedure:
1. In the TIM2 status and control register (T2SC):
a. Stop the TIM2 counter by setting the TIM2 stop bit, TSTOP.
b. Reset the TIM2 counter and prescaler by setting the TIM2 reset bit,
TRST.
2. In the TIM2 counter modulo registers (T2MODH:T2MODL), write the value
for the required PWM period.
3. In the TIM2 channel x registers (T2CHxH:T2CHxL), write the value for the
required pulse width.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
319
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
4. In TIM2 channel x status and control register (T2SCx):
a. Write 0:1 (for unbuffered output compare or PWM signals) or 1:0 (for
buffered output compare or PWM signals) to the mode select bits,
MSxB:MSxA. (See Table 19-2.)
b. Write 1 to the toggle-on-overflow bit, TOVx.
c. Write 1:0 (polarity 1 — to clear output on compare) or 1:1 (polarity 0 —
to set output on compare) to the edge/level select bits, ELSxB:ELSxA.
The output action on compare must force the output to the complement
of the pulse width level. (See Table 19-2.)
NOTE:
In PWM signal generation, do not program the PWM channel to toggle on output
compare. Toggling on output compare prevents reliable 0% duty cycle generation
and removes the ability of the channel to self-correct in the event of software error
or noise. Toggling on output compare can also cause incorrect PWM signal
generation when changing the PWM pulse width to a new, much larger value.
5. In the TIM2 status control register (T2SC), clear the TIM2 stop bit, TSTOP.
Setting MS0B links channels 0 and 1 and configures them for buffered PWM
operation. The TIM2 channel 0 registers (T2CH0H:T2CH0L) initially control the
buffered PWM output. TIM2 status control register 0 (T2SC0) controls and
monitors the PWM signal from the linked channels. MS0B takes priority over
MS0A.
Setting MS2B links channels 2 and 3 and configures them for buffered PWM
operation. The TIM2 channel 2 registers (T2CH2H:T2CH2L) initially control the
buffered PWM output. TIM2 status control register 2 (T2SC2) controls and
monitors the PWM signal from the linked channels. MS2B takes priority over
MS2A.
Setting MS4B links channels 4 and 5 and configures them for buffered PWM
operation. The TIM2 channel 4 registers (T2CH4H:T2CH4L) initially control the
buffered PWM output. TIM2 status control register 4 (T2SC4) controls and
monitors the PWM signal from the linked channels. MS4B takes priority over
MS4A.
Clearing the toggle-on-overflow bit, TOVx, inhibits output toggles on TIM2
overflows. Subsequent output compares try to force the output to a state it is
already in and have no effect. The result is a 0% duty cycle output.
Setting the channel x maximum duty cycle bit (CHxMAX) and setting the TOVx bit
generates a 100% duty cycle output. (See 19.8.4 TIM2 Channel Status and
Control Registers.)
Data Sheet
320
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
Interrupts
19.4 Interrupts
The following TIM2 sources can generate interrupt requests:
•
TIM2 overflow flag (TOF) — The TOF bit is set when the TIM2 counter
reaches the modulo value programmed in the TIM2 counter modulo
registers. The TIM2 overflow interrupt enable bit, TOIE, enables TIM2
overflow interrupt requests. TOF and TOIE are in the TIM2 status and
control register.
•
TIM2 channel flags (CH5F:CH0F) — The CHxF bit is set when an input
capture or output compare occurs on channel x. Channel x TIM2 CPU
interrupt requests are controlled by the channel x interrupt enable bit,
CHxIE.
19.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low-power standby modes.
19.5.1 Wait Mode
The TIM2 remains active after the execution of a WAIT instruction. In wait mode,
the TIM2 registers are not accessible by the CPU. Any enabled CPU interrupt
request from the TIM2 can bring the MCU out of wait mode.
If TIM2 functions are not required during wait mode, reduce power consumption by
stopping the TIM2 before executing the WAIT instruction.
19.5.2 Stop Mode
The TIM2 is inactive after the execution of a STOP instruction. The STOP
instruction does not affect register conditions or the state of the TIM2 counter. TIM2
operation resumes when the MCU exits stop mode.
19.6 TIM2 During Break Interrupts
A break interrupt stops the TIM2 counter.
The system integration module (SIM) controls whether status bits in other modules
can be cleared during the break state. The BCFE bit in the SIM break flag control
register (SBFCR) enables software to clear status bits during the break state. (See
15.7.3 Break Flag Control Register.)
To allow software to clear status bits during a break interrupt, write a 1 to the BCFE
bit. If a status bit is cleared during the break state, it remains cleared when the MCU
exits the break state.
To protect status bits during the break state, write a 0 to the BCFE bit. With BCFE
at 0 (its default state), software can read and write I/O registers during the break
state without affecting status bits. Some status bits have a 2-step read/write
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
321
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
clearing procedure. If software does the first step on such a bit before the break,
the bit cannot change during the break state as long as BCFE is at 0. After the
break, doing the second step clears the status bit.
19.7 I/O Signals
Port D shares two of its pins with the TIM2. Port F shares four of its pins with the
TIM2. PTD6/T2CH0 is an external clock input to the TIM2 prescaler. The six TIM2
channel I/O pins are PTD6/T2CH0, PTD7/T2CH1, PTF4/T2CH2, PTF5/T2CH3,
PTF6/T2CH4, and PTF7/T2CH5.
19.7.1 TIM2 Clock Pin (T2CH0)
T2CH0 is an external clock input that can be the clock source for the TIM2 counter
instead of the prescaled internal bus clock. Select the T2CH0 input by writing 1s to
the three prescaler select bits, PS[2:0]. (See 19.8.1 TIM2 Status and Control
Register.) The minimum TCLK pulse width is specified in 21.14 Timer Interface
Module Characteristics. The maximum TCLK frequency is the least: 4 MHz or
bus frequency ÷ 2.
When the PTD6/T2CH0 pin is the TIM2 clock input, it is an input regardless of the
state of the DDRD6 bit in data direction register D.
19.7.2 TIM2 Channel I/O Pins (T2CH5:T2CH2 and T2CH1:T2CH0)
Each channel I/O pin is programmable independently as an input capture pin or an
output compare pin. T2CH0, T2CH2, and T2CH4 can be configured as buffered
output compare or buffered PWM pins.
19.8 I/O Registers
These I/O registers control and monitor TIM2 operation:
•
•
•
•
TIM2 status and control register (T2SC)
TIM2 counter registers (T2CNTH:T2CNTL)
TIM2 counter modulo registers (T2MODH:T2MODL)
TIM2 channel status and control registers (T2SC0, T2SC1, T2SC2, T2SC3,
T2SC4, and T2SC5)
•
TIM2 channel registers (T2CH0H:T2CH0L, T2CH1H:T2CH1L,
T2CH2H:T2CH2L, T2CH3H:T2CH3L, T2CH4H:T2CH4L, and
T2CH5H:T2CH5L)
Data Sheet
322
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
I/O Registers
19.8.1 TIM2 Status and Control Register
The TIM2 status and control register:
•
•
•
•
•
Enables TIM2 overflow interrupts
Flags TIM2 overflows
Stops the TIM2 counter
Resets the TIM2 counter
Prescales the TIM2 counter clock
Address:
$002B
Bit 7
TOF
0
6
TOIE
0
5
TSTOP
1
4
0
3
0
2
PS2
0
1
PS1
0
Bit 0
PS0
0
Read:
Write:
Reset:
TRST
0
0
0
= Unimplemented
Figure 19-5. TIM2 Status and Control Register (T2SC)
TOF — TIM2 Overflow Flag Bit
This read/write flag is set when the TIM2 counter resets reaches the modulo
value programmed in the TIM2 counter modulo registers. Clear TOF by reading
the TIM2 status and control register when TOF is set and then writing a 0 to
TOF. If another TIM2 overflow occurs before the clearing sequence is complete,
then writing 0 to TOF has no effect. Therefore, a TOF interrupt request cannot
be lost due to inadvertent clearing of TOF. Reset clears the TOF bit. Writing a 1
to TOF has no effect.
1 = TIM2 counter has reached modulo value
0 = TIM2 counter has not reached modulo value
TOIE — TIM2 Overflow Interrupt Enable Bit
This read/write bit enables TIM2 overflow interrupts when the TOF bit becomes
set. Reset clears the TOIE bit.
1 = TIM2 overflow interrupts enabled
0 = TIM2 overflow interrupts disabled
TSTOP — TIM2 Stop Bit
This read/write bit stops the TIM2 counter. Counting resumes when TSTOP is
cleared. Reset sets the TSTOP bit, stopping the TIM2 counter until software
clears the TSTOP bit.
1 = TIM2 counter stopped
0 = TIM2 counter active
NOTE:
Do not set the TSTOP bit before entering wait mode if the TIM2 is required to exit
wait mode. Also when the TSTOP bit is set and the timer is configured for input
capture operation, input captures are inhibited until the TSTOP bit is cleared.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
323
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
TRST — TIM2 Reset Bit
Setting this write-only bit resets the TIM2 counter and the TIM2 prescaler.
Setting TRST has no effect on any other registers. Counting resumes from
$0000. TRST is cleared automatically after the TIM2 counter is reset and always
reads as 0. Reset clears the TRST bit.
1 = Prescaler and TIM2 counter cleared
0 = No effect
NOTE:
Setting the TSTOP and TRST bits simultaneously stops the TIM2 counter at a
value of $0000.
PS[2:0] — Prescaler Select Bits
These read/write bits select either the T2CH0 pin or one of the seven prescaler
outputs as the input to the TIM2 counter as Table 19-1 shows. Reset clears the
PS[2:0] bits.
Table 19-1. Prescaler Selection
PS[2:0]
000
TIM2 Clock Source
Internal bus clock ÷1
Internal bus clock ÷ 2
Internal bus clock ÷ 4
Internal bus clock ÷ 8
Internal bus clock ÷ 16
Internal bus clock ÷ 32
Internal bus clock ÷ 64
T2CH0
001
010
011
100
101
110
111
19.8.2 TIM2 Counter Registers
The two read-only TIM2 counter registers contain the high and low bytes of the
value in the TIM2 counter. Reading the high byte (T2CNTH) latches the contents
of the low byte (T2CNTL) into a buffer. Subsequent reads of T2CNTH do not affect
the latched T2CNTL value until T2CNTL is read. Reset clears the TIM2 counter
registers. Setting the TIM2 reset bit (TRST) also clears the TIM2 counter registers.
NOTE:
If T2CNTH is read during a break interrupt, be sure to unlatch T2CNTL by reading
T2CNTL before exiting the break interrupt. Otherwise, T2CNTL retains the value
latched during the break.
Data Sheet
324
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
I/O Registers
Address: $002C
T2CNTH
6
Bit 7
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
BIT 15
BIT 14
BIT 13
BIT 12
BIT 11
BIT 10
BIT 9
BIT 8
0
0
0
0
0
0
0
0
Address: $002D
Bit 7
T2CNTL
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0
0
0
0
0
0
0
0
= Unimplemented
Figure 19-6. TIM2 Counter Registers (T2CNTH and T2CNTL)
19.8.3 TIM2 Counter Modulo Registers
The read/write TIM2 modulo registers contain the modulo value for the TIM2
counter. When the TIM2 counter reaches the modulo value, the overflow flag (TOF)
becomes set, and the TIM2 counter resumes counting from $0000 at the next timer
clock. Writing to the high byte (T2MODH) inhibits the TOF bit and overflow
interrupts until the low byte (T2MODL) is written. Reset sets the TIM2 counter
modulo registers.
Address: $002E
Bit 7
T2MODH
6
5
BIT 13
1
4
BIT 12
1
3
BIT 11
1
2
BIT 10
1
1
BIT 9
1
Bit 0
BIT 8
1
Read:
Write:
Reset:
BIT 15
1
BIT 14
1
Address: $002F
Bit 7
T2MODL
6
5
BIT 5
1
4
BIT 4
1
3
BIT 3
1
2
BIT 2
1
1
BIT 1
1
Bit 0
BIT 0
1
Read:
Write:
Reset:
BIT 7
1
BIT 6
1
Figure 19-7. TIM2 Counter Modulo Registers (T2MODH and T2MODL)
NOTE:
Reset the TIM2 counter before writing to the TIM2 counter modulo registers.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
325
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
19.8.4 TIM2 Channel Status and Control Registers
Each of the TIM2 channel status and control registers:
•
•
•
•
•
Flags input captures and output compares
Enables input capture and output compare interrupts
Selects input capture, output compare, or PWM operation
Selects high, low, or toggling output on output compare
Selects rising edge, falling edge, or any edge as the active input capture
trigger
•
•
•
Selects output toggling on TIM2 overflow
Selects 0% and 100% PWM duty cycle
Selects buffered or unbuffered output compare/PWM operation
Address: $0030
Bit 7
T2SC0
6
5
4
3
2
1
TOV0
0
Bit 0
CH0MAX
0
Read:
Write:
Reset:
CH0F
CH0IE
MS0B
0
MS0A
0
ELS0B
0
ELS0A
0
0
0
0
T2SC1
6
Address: $0033
Bit 7
5
0
4
MS1A
0
3
ELS1B
0
2
ELS1A
0
1
TOV1
0
Bit 0
CH1MAX
0
Read:
Write:
Reset:
CH1F
CH1IE
0
0
0
T2SC2
6
0
Address: $0456
Bit 7
5
MS2B
0
4
MS2A
0
3
ELS2B
0
2
ELS2A
0
1
TOV2
0
Bit 0
CH2MAX
0
Read:
Write:
Reset:
CH2F
CH2IE
0
0
0
T2SC3
6
Address: $0459
Bit 7
5
0
4
MS3A
0
3
ELS3B
0
2
ELS3A
0
1
TOV3
0
Bit 0
CH3MAX
0
Read:
Write:
Reset:
CH3F
CH3IE
0
0
0
T2SC4
6
0
Address: $045C
Bit 7
5
MS4B
0
4
MS4A
0
3
ELS4B
0
2
ELS4A
0
1
TOV4
0
Bit 0
CH4MAX
0
Read:
Write:
Reset:
CH4F
CH4IE
0
0
0
= Unimplemented
Figure 19-8. TIM2 Channel Status and Control Registers
(T2SC0:T2SC5)
Data Sheet
326
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
I/O Registers
Address: $045F
T2SC5
6
Bit 7
CH5F
0
5
0
4
MS5A
0
3
ELS5B
0
2
ELS5A
0
1
TOV5
0
Bit 0
CH5MAX
0
Read:
Write:
Reset:
CH5IE
0
0
0
= Unimplemented
Figure 19-8. TIM2 Channel Status and Control Registers
(T2SC0:T2SC5) (Continued)
CHxF — Channel x Flag Bit
When channel x is an input capture channel, this read/write bit is set when an
active edge occurs on the channel x pin. When channel x is an output compare
channel, CHxF is set when the value in the TIM2 counter registers matches the
value in the TIM2 channel x registers.
When CHxIE = 1, clear CHxF by reading TIM2 channel x status and control
register with CHxF set, and then writing a 0 to CHxF. If another interrupt request
occurs before the clearing sequence is complete, then writing 0 to CHxF has no
effect. Therefore, an interrupt request cannot be lost due to inadvertent clearing
of CHxF.
Reset clears the CHxF bit. Writing a 1 to CHxF has no effect.
1 = Input capture or output compare on channel x
0 = No input capture or output compare on channel x
CHxIE — Channel x Interrupt Enable Bit
This read/write bit enables TIM2 CPU interrupts on channel x.
Reset clears the CHxIE bit.
1 = Channel x CPU interrupt requests enabled
0 = Channel x CPU interrupt requests disabled
MSxB — Mode Select Bit B
This read/write bit selects buffered output compare/PWM operation. MSxB
exists only in the TIM2 channel 0, TIM2 channel 2, and TIM2 channel 4 status
and control registers.
Setting MS0B disables the channel 1 status and control register and reverts
T2CH1 pin to general-purpose I/O.
Setting MS2B disables the channel 3 status and control register and reverts
T2CH3 pin to general-purpose I/O.
Setting MS4B disables the channel 5 status and control register and reverts
T2CH5 pin to general-purpose I/O.
Reset clears the MSxB bit.
1 = Buffered output compare/PWM operation enabled
0 = Buffered output compare/PWM operation disabled
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
327
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
MSxA — Mode Select Bit A
When ELSxB:ELSxA ≠ 00, this read/write bit selects either input capture
operation or unbuffered output compare/PWM operation. (See Table 19-2.)
1 = Unbuffered output compare/PWM operation
0 = Input capture operation
When ELSxB:ELSxA = 00, this read/write bit selects the initial output level of the
T2CHx pin once PWM, input capture, or output compare operation is enabled.
(See Table 19-2.) Reset clears the MSxA bit.
1 = Initial output level low
0 = Initial output level high
NOTE:
Before changing a channel function by writing to the MSxB or MSxA bit, set the
TSTOP and TRST bits in the TIM2 status and control register (T2SC).
Table 19-2. Mode, Edge, and Level Selection
MSxB MSxA
ELSxB
ELSxA
Mode
Configuration
Pin under port control;
initial output level high
X
X
0
1
0
0
Output preset
Pin under port control;
initial output level low
0
0
0
0
0
0
0
1
1
0
Capture on rising edge only
Capture on falling edge only
Input capture
Capture on rising
or falling edge
0
0
1
1
0
0
0
0
1
1
1
1
1
1
X
X
0
0
1
1
0
1
0
1
0
1
1
0
Software compare only
Toggle output on compare
Clear output on compare
Set output on compare
Toggle output on compare
Clear output on compare
Output compare
or PWM
Buffered
output
compare or
buffered PWM
1
X
1
1
Set output on compare
ELSxB and ELSxA — Edge/Level Select Bits
When channel x is an input capture channel, these read/write bits control the
active edge-sensing logic on channel x.
When channel x is an output compare channel, ELSxB and ELSxA control the
channel x output behavior when an output compare occurs.
When ELSxB and ELSxA are both clear, channel x is not connected to port D or
port F, and pin PTDx/T2CHx or pin PTFx/T2CHx is available as a general-
purpose I/O pin. Table 19-2 shows how ELSxB and ELSxA work. Reset clears
the ELSxB and ELSxA bits.
NOTE:
After initially enabling a TIM2 channel register for input capture operation and
selecting the edge sensitivity, clear CHxF to ignore any erroneous edge detection
flags.
Data Sheet
328
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
I/O Registers
TOVx — Toggle-On-Overflow Bit
When channel x is an output compare channel, this read/write bit controls the
behavior of the channel x output when the TIM2 counter overflows. When
channel x is an input capture channel, TOVx has no effect. Reset clears the
TOVx bit.
1 = Channel x pin toggles on TIM2 counter overflow.
0 = Channel x pin does not toggle on TIM2 counter overflow.
NOTE:
When TOVx is set, a TIM2 counter overflow takes precedence over a channel x
output compare if both occur at the same time.
CHxMAX — Channel x Maximum Duty Cycle Bit
When the TOVx bit is at a 1 and clear output on compare is selected, setting the
CHxMAX bit forces the duty cycle of buffered and unbuffered PWM signals to
100%. As Figure 19-9 shows, the CHxMAX bit takes effect in the cycle after it
is set or cleared. The output stays at 100% duty cycle level until the cycle after
CHxMAX is cleared.
NOTE:
The 100% PWM duty cycle is defined as a continuous high level if the PWM polarity
is 1 and a continuous low level if the PWM polarity is 0. Conversely, a 0% PWM
duty cycle is defined as a continuous low level if the PWM polarity is 1 and a
continuous high level if the PWM polarity is 0.
OVERFLOW
OVERFLOW
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
PTDx/T2CHx
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
CHxMAX
Figure 19-9. CHxMAX Latency
19.8.5 TIM2 Channel Registers
These read/write registers contain the captured TIM2 counter value of the input
capture function or the output compare value of the output compare function. The
state of the TIM2 channel registers after reset is unknown.
In input capture mode (MSxB:MSxA = 0:0), reading the high byte of the TIM2
channel x registers (T2CHxH) inhibits input captures until the low byte (T2CHxL) is
read.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
329
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
In output compare mode (MSxB:MSxA ≠ 0:0), writing to the high byte of the TIM2
channel x registers (T2CHxH) inhibits output compares until the low byte (T2CHxL)
is written.
Address: $0031
Bit 7
T2CH0H
6
5
4
3
2
1
Bit 0
Bit 8
Read:
Write:
Reset:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Indeterminate after reset
Address: $0032
Bit 7
T2CH0L
6
5
4
3
2
1
Bit 0
Bit 0
Read:
Write:
Reset:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Indeterminate after reset
Address: $0034
Bit 7
T2CH1H
6
5
4
3
2
1
Bit 0
Bit 8
Read:
Write:
Reset:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Indeterminate after reset
Address: $0035
Bit 7
T2CH1L
6
5
4
3
2
1
Bit 0
Bit 0
Read:
Write:
Reset:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Indeterminate after reset
Address: $0457
Bit 7
T2CH2H
6
5
4
3
2
1
Bit 0
Bit 8
Read:
Write:
Reset:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Indeterminate after reset
Address: $0458
Bit 7
T2CH2L
6
5
4
3
2
1
Bit 0
Bit 0
Read:
Write:
Reset:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Indeterminate after reset
Address: $045A
Bit 7
T2CH3H
6
5
4
3
2
1
Bit 0
Bit 8
Read:
Write:
Reset:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Indeterminate after reset
Figure 19-10. TIM2 Channel Registers (T2CH0H/L:T2CH5H/L)
Data Sheet
330
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
I/O Registers
Address: $045B
T2CH3L
6
Bit 7
5
4
3
2
1
Bit 0
Bit 0
Read:
Write:
Reset:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Indeterminate after reset
Address: $045D
Bit 7
T2CH4H
6
5
4
3
2
1
Bit 0
Bit 8
Read:
Write:
Reset:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Indeterminate after reset
Address: $045E
Bit 7
T2CH4L
6
5
4
3
2
1
Bit 0
Bit 0
Read:
Write:
Reset:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Indeterminate after reset
Address: $0460
Bit 7
T2CH5H
6
5
4
3
2
1
Bit 0
Bit 8
Read:
Write:
Reset:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Indeterminate after reset
Address: $0461
Bit 7
T2CH5L
6
5
4
3
2
1
Bit 0
Bit 0
Read:
Write:
Reset:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Indeterminate after reset
Figure 19-10. TIM2 Channel Registers (T2CH0H/L:T2CH5H/L) (Continued)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
331
MOTOROLA
Timer Interface Module (TIM2)
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Timer Interface Module (TIM2)
Data Sheet
332
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Timer Interface Module (TIM2)
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 20. Development Support
20.1 Introduction
This section describes the break module, the monitor module (MON), and the
monitor mode entry methods.
20.2 Break Module (BRK)
The break module can generate a break interrupt that stops normal program flow
at a defined address to enter a background program.
Features of the break module include:
•
•
•
•
Accessible input/output (I/O) registers during the break Interrupt
Central processor unit (CPU) generated break interrupts
Software-generated break interrupts
Computer operating properly (COP) disabling during break interrupts
20.2.1 Functional Description
When the internal address bus matches the value written in the break address
registers, the break module issues a breakpoint signal (BKPT) to the system
integration module (SIM). The SIM then causes the CPU to load the instruction
register with a software interrupt instruction (SWI). The program counter vectors to
$FFFC and $FFFD ($FEFC and $FEFD in monitor mode).
The following events can cause a break interrupt to occur:
•
A CPU generated address (the address in the program counter) matches
the contents of the break address registers.
•
Software writes a 1 to the BRKA bit in the break status and control register.
When a CPU generated address matches the contents of the break address
registers, the break interrupt is generated. A return-from-interrupt instruction (RTI)
in the break routine ends the break interrupt and returns the microcontroller unit
(MCU) to normal operation.
Figure 20-2 shows the structure of the break module.
Figure 20-3 provides a summary of the I/O registers.
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
333
MOTOROLA
Development Support
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
B
P O R T
D D R B
P O R T F
D D R F
G T R P O
D D R G
A T R P O
D D R A
C
P O R T
D D R C
E
P O R T
D D R E
P O R T D
D D R
D
Data Sheet
334
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Development Support MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
Break Module (BRK)
ADDRESS BUS[15:8]
BREAK ADDRESS REGISTER HIGH
8-BIT COMPARATOR
ADDRESS BUS[15:0]
CONTROL
BKPT
(TO SIM)
8-BIT COMPARATOR
BREAK ADDRESS REGISTER LOW
ADDRESS BUS[7:0]
Figure 20-2. Break Module Block Diagram
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Read:
SBSW
Note(1)
0
Break Status Register
(BSR) Write:
R
R
R
R
R
R
R
$FE00
See page 338.
Reset:
Read:
Break Flag Control
BCFE
0
R
R
R
R
R
R
R
$FE03
$FE09
$FE0A
$FE0B
Register (BFCR) Write:
See page 339.
Reset:
Read:
Break Address High
Register (BRKH) Write:
Bit 15
0
Bit 14
0
Bit 13
0
Bit 12
0
Bit 11
0
Bit 10
0
Bit 9
0
Bit 8
0
See page 338.
Reset:
Read:
Break Address Low
Register (BRKL) Write:
Bit 7
0
Bit 6
0
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
See page 338.
Reset:
0
0
0
0
0
0
0
0
0
0
0
0
Read:
Break Status and Control
Register (BRKSCR) Write:
BRKE
0
BRKA
See page 337.
Reset:
0
0
0
0
0
0
0
1. Writing a 0 clears SBSW.
= Unimplemented
R
= Reserved
Figure 20-3. Break I/O Register Summary
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
335
MOTOROLA
Development Support
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
When the internal address bus matches the value written in the break address
registers or when software writes a 1 to the BRKA bit in the break status and control
register, the CPU starts a break interrupt by:
•
•
Loading the instruction register with the SWI instruction
Loading the program counter with $FFFC and $FFFD ($FEFC and $FEFD
in monitor mode)
The break interrupt timing is:
•
When a break address is placed at the address of the instruction opcode,
the instruction is not executed until after completion of the break interrupt
routine.
•
•
When a break address is placed at an address of an instruction operand, the
instruction is executed before the break interrupt.
When software writes a 1 to the BRKA bit, the break interrupt occurs just
before the next instruction is executed.
By updating a break address and clearing the BRKA bit in a break interrupt routine,
a break interrupt can be generated continuously.
CAUTION:
A break address should be placed at the address of the instruction opcode. When
software does not change the break address and clears the BRKA bit in the first
break interrupt routine, the next break interrupt will not be generated after exiting
the interrupt routine even when the internal address bus matches the value written
in the break address registers.
20.2.1.1 Flag Protection During Break Interrupts
The system integration module (SIM) controls whether or not module status bits
can be cleared during the break state. The BCFE bit in the break flag control
register (BFCR) enables software to clear status bits during the break state. See
15.7.3 Break Flag Control Register and the Break Interrupts subsection for
each module.
20.2.1.2 TIM During Break Interrupts
A break interrupt stops the timer counter.
20.2.1.3 COP During Break Interrupts
The COP is disabled during a break interrupt when VTST is present on the RST pin.
Data Sheet
336
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Development Support
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
Break Module (BRK)
20.2.2 Break Module Registers
These registers control and monitor operation of the break module:
•
•
•
•
•
Break status and control register (BRKSCR)
Break address register high (BRKH)
Break address register low (BRKL)
Break status register (BSR)
Break flag control register (BFCR)
20.2.2.1 Break Status and Control Register
The break status and control register (BRKSCR) contains break module enable
and status bits.
$FE0B
Bit 7
Address:
6
BRKA
0
5
0
4
0
3
0
2
0
1
0
Bit 0
0
Read:
Write:
Reset:
BRKE
0
0
0
0
0
0
0
= Unimplemented
Figure 20-4. Break Status and Control Register (BRKSCR)
BRKE — Break Enable Bit
This read/write bit enables breaks on break address register matches. Clear
BRKE by writing a 0 to bit 7. Reset clears the BRKE bit.
1 = Breaks enabled on 16-bit address match
0 = Breaks disabled
BRKA — Break Active Bit
This read/write status and control bit is set when a break address match occurs.
Writing a 1 to BRKA generates a break interrupt. Clear BRKA by writing a 0 to
it before exiting the break routine. Reset clears the BRKA bit.
1 = Break address match
0 = No break address match
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
337
MOTOROLA
Development Support
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
20.2.2.2 Break Address Registers
The break address registers (BRKH and BRKL) contain the high and low bytes of
the desired breakpoint address. Reset clears the break address registers.
$FE09
Address:
Bit 7
6
Bit 14
0
5
Bit 13
0
4
Bit 12
0
3
Bit 11
0
2
Bit 10
0
1
Bit 9
0
Bit 0
Bit 8
0
Read:
Write:
Reset:
Bit 15
0
Figure 20-5. Break Address Register High (BRKH)
$FE0A
Address:
Bit 7
Bit 7
0
6
Bit 6
0
5
Bit 5
0
4
Bit 4
0
3
Bit 3
0
2
Bit 2
0
1
Bit 1
0
Bit 0
Bit 0
0
Read:
Write:
Reset:
Figure 20-6. Break Address Register Low (BRKL)
20.2.2.3 Break Status Register
The break status register (BSR) contains a flag to indicate that a break caused an
exit from wait mode. This register is only used in emulation mode.
Address: $FE00
Bit 7
6
5
4
3
2
1
Bit 0
R
Read:
Write:
Reset:
SBSW
Note(1)
0
R
R
R
R
R
R
R
= Reserved
1. Writing a 0 clears SBSW.
Figure 20-7. Break Status Register (BSR)
SBSW — SIM Break Stop/Wait
SBSW can be read within the break state SWI routine. The user can modify the
return address on the stack by subtracting one from it.
1 = Wait mode was exited by break interrupt
0 = Wait mode was not exited by break interrupt
Data Sheet
338
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Development Support
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
Monitor Module (MON)
20.2.2.4 Break Flag Control Register
The break control register (BFCR) contains a bit that enables software to clear
status bits while the MCU is in a break state.
$FE03
Address:
Bit 7
6
5
4
3
2
1
Bit 0
R
Read:
Write:
Reset:
BCFE
R
R
R
R
R
R
0
= Reserved
R
Figure 20-8. Break Flag Control Register (BFCR)
BCFE — Break Clear Flag Enable Bit
This read/write bit enables software to clear status bits by accessing status
registers while the MCU is in a break state. To clear status bits during the break
state, the BCFE bit must be set.
1 = Status bits clearable during break
0 = Status bits not clearable during break
20.2.3 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power- consumption standby
modes. If enabled, the break module will remain enabled in wait and stop modes.
However, since the internal address bus does not increment in these modes, a
break interrupt will never be triggered.
20.3 Monitor Module (MON)
The monitor module allows debugging and programming of the microcontroller unit
(MCU) through a single-wire interface with a host computer. Monitor mode entry
can be achieved without use of the higher test voltage, VTST, as long as vector
addresses $FFFE and $FFFF are blank, thus reducing the hardware requirements
for in-circuit programming.
Features of the monitor module include:
•
•
Normal user-mode pin functionality
One pin dedicated to serial communication between MCU and host
computer
•
•
•
Standard non-return-to-zero (NRZ) communication with host computer
Standard communication baud rate (7200 @ 2-MHz bus frequency)
Execution of code in random-access memory (RAM) or FLASH
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
339
MOTOROLA
Development Support
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
•
FLASH memory security feature(1)
•
•
FLASH memory programming interface
Monitor mode entry without high voltage, VTST, if reset vector is blank
($FFFE and $FFFF contain $FF)
•
Normal monitor mode entry if VTST is applied to IRQ
20.3.1 Functional Description
Figure 20-9 shows a simplified diagram of the monitor mode.
The monitor module receives and executes commands from a host computer.
Figure 20-10 and Figure 20-11 show example circuits used to enter monitor mode
and communicate with a host computer via a standard RS-232 interface.
Simple monitor commands can access any memory address. In monitor mode, the
MCU can execute code downloaded into RAM by a host computer while most MCU
pins retain normal operating mode functions. All communication between the host
computer and the MCU is through the PTA0 pin. A level-shifting and multiplexing
interface is required between PTA0 and the host computer. PTA0 is used in a
wired-OR configuration and requires a pullup resistor.
Table 20-1 shows the pin conditions for entering monitor mode. As specified in the
table, monitor mode may be entered after a power-on reset (POR) and will allow
communication at 7200 baud provided one of the following sets of conditions is
met:
•
•
•
If $FFFE and $FFFF does not contain $FF (programmed state):
–
–
–
The external clock is 4.0 MHz (7200 baud)
PTB4 = low
IRQ = VTST
If $FFFE and $FFFF do not contain $FF (programmed state):
–
–
–
The external clock is 8.0 MHz (7200 baud)
PTB4 = high
IRQ = VTST
If $FFFE and $FFFF contain $FF (erased state):
–
–
The external clock is 8.0 MHz (7200 baud)
IRQ = VDD (this can be implemented through the internal IRQ pullup) or
VSS
1. No security feature is absolutely secure. However, Motorola’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
Data Sheet
340
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Development Support
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
Monitor Module (MON)
POR RESET
YES
NO
IRQ = VTST
?
CONDITIONS
PTA0 = 1,
PTA1 = 0, RESET
VECTOR BLANK?
PTA0 = 1, PTA1 = 0,
PTB0 = 1, AND
PTB1 = 0?
NO
NO
FROM Table 20-1
YES
YES
FORCED
MONITOR MODE
NORMAL
USER MODE
NORMAL
MONITOR MODE
INVALID
USER MODE
HOST SENDS
8 SECURITY BYTES
YES
IS RESET
POR?
NO
ARE ALL
SECURITY BYTES
CORRECT?
YES
NO
ENABLE FLASH
DISABLE FLASH
MONITOR MODE ENTRY
DEBUGGING
AND FLASH
PROGRAMMING
(IF FLASH
IS ENABLED)
EXECUTE
MONITOR CODE
NO
YES
DOES RESET
OCCUR?
Figure 20-9. Simplified Monitor Mode Entry Flowchart
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
341
MOTOROLA
Development Support
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
MC68HC908GZ60
VDD
N.C.
RST
VDD
47 pF
VDDA
OSC2
VDDAD
MAX232
VDD
0.1 µF
10 MΩ
27 pF
1
16
15
VCC
C1+
VDD
+
+
+
OSC1
IRQ
1 µF
1 µF
8 MHz
10 k
3
4
1 µF
GND
C1–
C2+
PTB4
PTB0
+
10 k
1 kΩ
2
6
V+
V–
10 k
10 k
VDD
1 µF
9.1 V
PTB1
PTA1
VSSAD
5
C2–
1 µF
+
10 kΩ
74HC125
DB9
5
10
9
2
7
8
6
PTA0
74HC125
3
2
VSSA
VSS
4
3
5
1
Figure 20-10. Normal Monitor Mode Circuit
MC68HC908GZ60
VDD
N.C.
RST
VDD
VDDA
47 pF
27 pF
OSC2
VDDAD
MAX232
VDD
0.1 µF
10 MΩ
1
16
15
VCC
C1+
+
+
+
OSC1
IRQ
1 µF
1 µF
8 MHz
3
4
1 µF
GND
C1–
C2+
+
PTB4
PTB0
PTB1
N.C.
2
6
N.C.
N.C.
V+
V–
N.C.
VDD
1 µF
5
C2–
10 k
1 µF
+
PTA1
10 kΩ
74HC125
DB9
5
10
9
6
2
7
8
PTA0
VSSAD
VSSA
VSS
74HC125
3
2
4
3
5
1
Figure 20-11. Forced Monitor Mode
Data Sheet
342
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Development Support
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
Monitor Module (MON)
Table 20-1. Monitor Mode Signal Requirements and Options
Serial
Communication
Mode
Selection
Communication
Speed
Divider
Reset
Vector
Mode
IRQ RST
PLL
COP
External
Bus
Baud
PTA0
PTA1 PTB0 PTB1 PTB4
Clock Frequency Rate
VDD
VTST
or
VTST
X
X
1
0
0
0
X
1
1
0
0
0
1
OFF Disabled 4.0 MHz
OFF Disabled 8.0 MHz
OFF Disabled 8.0 MHz
2.0 MHz
2.0 MHz
2.0 MHz
7200
7200
7200
Normal
Monitor
VDD
VTST
or
VTST
1
1
X
VDD
Forced
Monitor
$FF
(blank)
VDD
or
VSS
X
X
X
X
X
X
VDD VDD
or or
VSS VTST
Not
$FF
User
X
Enabled
—
X
X
X
MON08
Function
[Pin No.]
VTST
[6]
RST
[4]
COM
[8]
SSEL MOD0 MOD1 DIV4
[10] [12] [14] [16]
OSC1
[13]
—
—
—
—
1. PTA0 must have a pullup resistor to VDD in monitor mode.
2. Communication speed in the table is an example to obtain a baud rate of 7200. Baud rate using external oscillator is bus
frequency / 278.
3. External clock is a 4.0 MHz or 8.0 MHz crystal on OSC1 and OSC2 or a canned oscillator on OSC1.
4. X = don’t care
5. MON08 pin refers to P&E Microcomputer Systems’ MON08-Cyclone 2 by 8-pin connector.
NC
NC
1
3
2
4
GND
RST
NC
5
6
IRQ
NC
7
8
PTA0
PTA1
PTB0
PTB1
PTB4
NC
9
10
12
14
16
NC
11
13
15
OSC1
VDD
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
343
MOTOROLA
Development Support
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
Enter monitor mode with pin configuration shown in Table 20-1 by pulling RST low
and then high. The rising edge of RST latches monitor mode. Once monitor mode
is latched, the levels on the port pins except PTA0 can change.
Once out of reset, the MCU waits for the host to send eight security bytes (see
20.3.2 Security). After the security bytes, the MCU sends a break signal (10
consecutive 0s) to the host, indicating that it is ready to receive a command.
20.3.1.1 Normal Monitor Mode
If VTST is applied to IRQ and PTB4 is low upon monitor mode entry, the bus
frequency is a divide-by-two of the input clock. If PTB4 is high with VTST applied to
IRQ upon monitor mode entry, the bus frequency will be a divide-by-four of the
input clock. Holding the PTB4 pin low when entering monitor mode causes a
bypass of a divide-by-two stage at the oscillator only if VTST is applied to IRQ. In
this event, the CGMOUT frequency is equal to the CGMXCLK frequency, and the
OSC1 input directly generates internal bus clocks. In this case, the OSC1 signal
must have a 50% duty cycle at maximum bus frequency.
When monitor mode was entered with VTST on IRQ, the computer operating
properly (COP) is disabled as long as VTST is applied to either IRQ or RST.
This condition states that as long as VTST is maintained on the IRQ pin after
entering monitor mode, or if VTST is applied to RST after the initial reset to get into
monitor mode (when VTST was applied to IRQ), then the COP will be disabled. In
the latter situation, after VTST is applied to the RST pin, VTST can be removed from
the IRQ pin in the interest of freeing the IRQ for normal functionality in monitor
mode.
20.3.1.2 Forced Monitor Mode
If entering monitor mode without high voltage on IRQ, then all port B pin
requirements and conditions, including the PTB4 frequency divisor selection, are
not in effect. This is to reduce circuit requirements when performing in-circuit
programming.
NOTE:
If the reset vector is blank and monitor mode is entered, the chip will see an
additional reset cycle after the initial power-on reset (POR). Once the reset vector
has been programmed, the traditional method of applying a voltage, VTST, to IRQ
must be used to enter monitor mode.
An external oscillator of 8 MHz is required for a baud rate of 7200, as the internal
bus frequency is automatically set to the external frequency divided by four.
When the forced monitor mode is entered the COP is always disabled regardless
of the state of IRQ or RST.
Data Sheet
344
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Development Support
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
Monitor Module (MON)
20.3.1.3 Monitor Vectors
In monitor mode, the MCU uses different vectors for reset, SWI (software interrupt),
and break interrupt than those for user mode. The alternate vectors are in the $FE
page instead of the $FF page and allow code execution from the internal monitor
firmware instead of user code.
Table 20-2 summarizes the differences between user mode and monitor mode.
Table 20-2. Mode Differences
Functions
Break Break
Modes
Reset
Reset
SWI
SWI
Vector High Vector Low Vector High Vector Low Vector High Vector Low
User
$FFFE
$FEFE
$FFFF
$FEFF
$FFFC
$FEFC
$FFFD
$FEFD
$FFFC
$FEFC
$FFFD
$FEFD
Monitor
20.3.1.4 Data Format
Communication with the monitor ROM is in standard non-return-to-zero (NRZ)
mark/space data format. Transmit and receive baud rates must be identical.
NEXT
START
BIT
START
BIT
BIT 6
STOP
BIT
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 7
Figure 20-12. Monitor Data Format
20.3.1.5 Break Signal
A start bit (0) followed by nine 0 bits is a break signal. When the monitor receives
a break signal, it drives the PTA0 pin high for the duration of approximately two bits
and then echoes back the break signal.
MISSING STOP BIT
APPROXIMATELY 2 BITS DELAY
BEFORE ZERO ECHO
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Figure 20-13. Break Transaction
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
345
MOTOROLA
Development Support
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
20.3.1.6 Baud Rate
The communication baud rate is controlled by the crystal frequency or external
clock and the state of the PTB4 pin (when IRQ is set to VTST) upon entry into
monitor mode. If monitor mode was entered with VDD on IRQ and the reset vector
blank, then the baud rate is independent of PTB4.
Table 20-1 also lists external frequencies required to achieve a standard baud rate
of 7200 bps. The effective baud rate is the bus frequency divided by 278. If using
a crystal as the clock source, be aware of the upper frequency limit that the internal
clock module can handle. See 21.7 5.0-Volt Control Timing or 21.8 3.3-Volt
Control Timing for this limit.
20.3.1.7 Commands
The monitor ROM firmware uses these commands:
•
•
•
•
•
•
READ (read memory)
WRITE (write memory)
IREAD (indexed read)
IWRITE (indexed write)
READSP (read stack pointer)
RUN (run user program)
The monitor ROM firmware echoes each received byte back to the PTA0 pin for
error checking. An 11-bit delay at the end of each command allows the host to send
a break character to cancel the command. A delay of two bit times occurs before
each echo and before READ, IREAD, or READSP data is returned. The data
returned by a read command appears after the echo of the last byte of the
command.
NOTE:
Wait one bit time after each echo before sending the next byte.
FROM
HOST
ADDRESS
HIGH
ADDRESS
HIGH
ADDRESS
LOW
ADDRESS
LOW
READ
READ
DATA
4
4
1
1
4
1
3, 2
4
ECHO
RETURN
Notes:
1 = Echo delay, approximately 2 bit times
2 = Data return delay, approximately 2 bit times
3 = Cancel command delay, 11 bit times
4 = Wait 1 bit time before sending next byte.
Figure 20-14. Read Transaction
Data Sheet
346
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Development Support
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
Monitor Module (MON)
FROM
HOST
ADDRESS
HIGH
ADDRESS
HIGH
ADDRESS
LOW
ADDRESS
LOW
DATA
DATA
WRITE
WRITE
3
3
1
1
3
1
3
1
2, 3
ECHO
Notes:
1 = Echo delay, approximately 2 bit times
2 = Cancel command delay, 11 bit times
3 = Wait 1 bit time before sending next byte.
Figure 20-15. Write Transaction
A brief description of each monitor mode command is given in Table 20-3 through
Table 20-8.
Table 20-3. READ (Read Memory) Command
Description Read byte from memory
Operand 2-byte address in high-byte:low-byte order
Data Returned Returns contents of specified address
Opcode $4A
Command Sequence
SENT TO MONITOR
ADDRESS ADDRESS ADDRESS
HIGH HIGH LOW
ADDRESS
LOW
READ
READ
DATA
ECHO
RETURN
Table 20-4. WRITE (Write Memory) Command
Description Write byte to memory
Operand 2-byte address in high-byte:low-byte order; low byte followed by data byte
Data Returned None
Opcode $49
Command Sequence
FROM HOST
ADDRESS ADDRESS ADDRESS ADDRESS
LOW
DATA
DATA
WRITE
WRITE
HIGH
HIGH
LOW
ECHO
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Development Support
Data Sheet
347
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
Table 20-5. IREAD (Indexed Read) Command
Description Read next 2 bytes in memory from last address accessed
Operand None
Data Returned Returns contents of next two addresses
Opcode $1A
Command Sequence
FROM HOST
IREAD
IREAD
DATA
DATA
ECHO
RETURN
Table 20-6. IWRITE (Indexed Write) Command
Description Write to last address accessed + 1
Operand Single data byte
Data Returned None
Opcode $19
Command Sequence
FROM HOST
DATA
DATA
IWRITE
ECHO
IWRITE
A sequence of IREAD or IWRITE commands can access a block of memory
sequentially over the full 64-Kbyte memory map.
Table 20-7. READSP (Read Stack Pointer) Command
Description Reads stack pointer
Operand None
Data Returned Returns incremented stack pointer value (SP + 1) in high-byte:low-byte order
Opcode $0C
Command Sequence
FROM HOST
SP
HIGH
SP
LOW
READSP
READSP
ECHO
RETURN
Data Sheet
348
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Development Support MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
Monitor Module (MON)
Table 20-8. RUN (Run User Program) Command
Description Executes PULH and RTI instructions
Operand None
Data Returned None
Opcode $28
Command Sequence
FROM HOST
RUN
RUN
ECHO
The MCU executes the SWI and PSHH instructions when it enters monitor mode.
The RUN command tells the MCU to execute the PULH and RTI instructions.
Before sending the RUN command, the host can modify the stacked CPU registers
to prepare to run the host program. The READSP command returns the
incremented stack pointer value, SP + 1. The high and low bytes of the program
counter are at addresses SP + 5 and SP + 6.
SP
HIGH BYTE OF INDEX REGISTER
CONDITION CODE REGISTER
ACCUMULATOR
SP + 1
SP + 2
SP + 3
SP + 4
SP + 5
SP + 6
SP + 7
LOW BYTE OF INDEX REGISTER
HIGH BYTE OF PROGRAM COUNTER
LOW BYTE OF PROGRAM COUNTER
Figure 20-16. Stack Pointer at Monitor Mode Entry
20.3.2 Security
A security feature discourages unauthorized reading of FLASH locations while in
monitor mode. The host can bypass the security feature at monitor mode entry by
sending eight security bytes that match the bytes at locations $FFF6–$FFFD.
Locations $FFF6–$FFFD contain user-defined data.
NOTE:
Do not leave locations $FFF6–$FFFD blank. For security reasons, program
locations $FFF6–$FFFD even if they are not used for vectors.
During monitor mode entry, the MCU waits after the power-on reset for the host to
send the eight security bytes on pin PTA0. If the received bytes match those at
locations $FFF6–$FFFD, the host bypasses the security feature and can read all
FLASH locations and execute code from FLASH. Security remains bypassed until
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
349
MOTOROLA
Development Support
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Development Support
a power-on reset occurs. If the reset was not a power-on reset, security remains
bypassed and security code entry is not required. See Figure 20-17.
Upon power-on reset, if the received bytes of the security code do not match the
data at locations $FFF6–$FFFD, the host fails to bypass the security feature. The
MCU remains in monitor mode, but reading a FLASH location returns an invalid
value and trying to execute code from FLASH causes an illegal address reset. After
receiving the eight security bytes from the host, the MCU transmits a break
character, signifying that it is ready to receive a command.
NOTE:
The MCU does not transmit a break character until after the host sends the eight
security bytes.
VDD
4096 + 32 CGMXCLK CYCLES
RST
FROM HOST
PA0
5
1
1
4
1
4
2
1
FROM MCU
Notes:
1 = Echo delay, approximately 2 bit times
2 = Data return delay, approximately 2 bit times
4 = Wait 1 bit time before sending next byte
5 = Wait until the monitor ROM runs
Figure 20-17. Monitor Mode Entry Timing
To determine whether the security code entered is correct, check to see if bit 6 of
RAM address $40 is set. If it is, then the correct security code has been entered
and FLASH can be accessed.
If the security sequence fails, the device should be reset by a power-on reset and
brought up in monitor mode to attempt another entry. After failing the security
sequence, the FLASH module can also be mass erased by executing an erase
routine that was downloaded into internal RAM. The mass erase operation clears
the security code locations so that all eight security bytes become $FF (blank).
Data Sheet
350
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Development Support
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 21. Electrical Specifications
21.1 Introduction
This section contains electrical and timing specifications.
21.2 Absolute Maximum Ratings
Maximum ratings are the extreme limits to which the MCU can be exposed without
permanently damaging it.
NOTE:
This device is not guaranteed to operate properly at the maximum ratings. Refer to
21.5 5.0-Vdc Electrical Characteristics for guaranteed operating conditions.
Characteristic(1)
Supply voltage
Symbol
VDD
Value
Unit
V
–0.3 to + 6.0
VIn
VSS – 0.3 to VDD + 0.3
Input voltage
V
Maximum current per pin
excluding those specified below
I
± 15
± 25
mA
mA
Maximum current for pins
PTC0–PTC4
IPTC0–PTC4
Maximum current into VDD
Maximum current out of VSS
Storage temperature
Imvdd
Imvss
Tstg
150
150
mA
mA
°C
–55 to +150
1. Voltages referenced to VSS
NOTE:
This device contains circuitry to protect the inputs against damage due to high
static voltages or electric fields; however, it is advised that normal precautions be
taken to avoid application of any voltage higher than maximum-rated voltages to
this high-impedance circuit. For proper operation, it is recommended that VIn and
VOut be constrained to the range VSS ≤ (VIn or VOut) ≤ VDD. Reliability of operation
is enhanced if unused inputs are connected to an appropriate logic voltage level
(for example, either VSS or VDD).
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
351
MOTOROLA
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
21.3 Functional Operating Range
Characteristic
Symbol
Value
Unit
TA
Operating temperature range
Operating voltage range
–40 to +125
°C
5.0 ±10%
3.3 ±10%
VDD
V
21.4 Thermal Characteristics
Characteristic
Thermal resistance
Symbol
Value
Unit
32-pin LQFP
48-pin LQFP
64-pin QFP
95
95
54
θJA
°C/W
PI/O
PD
I/O pin power dissipation
Power dissipation(1)
User determined
W
W
PD = (IDD × VDD) + PI/O
K/(TJ + 273 °C)
=
P
D × (TA + 273 °C)
+ PD2 × θJA
Constant(2)
K
W/°C
°C
TJ
TA + (PD × θJA)
Average junction temperature
1. Power dissipation is a function of temperature.
2. K is a constant unique to the device. K can be determined for a known TA and measured PD.
With this value of K, PD and TJ can be determined for any value of TA.
Data Sheet
352
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Electrical Specifications
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
5.0-Vdc Electrical Characteristics
21.5 5.0-Vdc Electrical Characteristics
Characteristic(1)
Typ(2)
Symbol
Min
Max
Unit
Output high voltage
(ILoad = –2.0 mA) all I/O pins
VOH
VOH
VOH
IOH1
VDD – 0.8
VDD – 1.5
VDD – 1.5
—
—
—
—
—
—
—
—
50
V
V
V
(ILoad = –10.0 mA) all I/O pins
(ILoad = –20.0 mA) pins PTC0–PTC4, PTF0–PTF3 only
Maximum combined IOH for port PTA7–PTA3,
mA
port PTC0–PTC1, port E, port PTD0–PTD3,
port PTF0–PTF3, port PTG4–PTG7
Maximum combined IOH for port PTA2–PTA0,
IOH2
—
—
50
mA
mA
—
—
port B, port PTC2–PTC6, port PTD4–PTD7,
port PTF4–PTF7, port PTG0–PTG3
Maximum total IOH for all port pins
IOHT
100
Output low voltage
(ILoad = 1.6 mA) all I/O pins
VOL
VOL
VOL
IOL1
—
—
—
—
0.4
1.5
1.5
50
V
V
V
—
—
—
—
(ILoad = 10 mA) all I/O pins
(ILoad = 20 mA) pins PTC0–PTC4, PTF0–PTF3 only
Maximum combined IOH for port PTA7–PTA3,
mA
port PTC0–PTC1, port E, port PTD0–PTD3,
port PTF0–PTF3, port PTG4–PTG7
—
Maximum combined IOH for port PTA2–PTA0,
IOL2
—
50
mA
port B, port PTC2–PTC6, port PTD4–PTD7,
port PTF4–PTF7, port PTG0–PTG3
Maximum total IOL for all port pins
—
IOLT
VIH
VIL
—
—
100
VDD
mA
V
Input high voltage
All ports, IRQ, RST, OSC1
0.7 × VDD
Input low voltage
All ports, IRQ, RST, OSC1
VSS
0.2 × VDD
—
V
VDD supply current
Run(3)
Wait(4)
—
—
20
6
30
12
mA
mA
Stop(5)
IDD
25°C
—
—
—
—
—
3
20
300
50
500
—
—
—
—
—
µA
µA
µA
µA
µA
25°C with TBM enabled(6)
25°C with LVI and TBM enabled(6)
–40°C to 125°C with TBM enabled(6)
–40°C to 125°C with LVI and TBM enabled(6)
IINJ
IINJTOT
IIL
DC injection current, all ports
–2
–25
–1
—
—
—
+2
+25
+1
mA
mA
µA
Total dc current injection (sum of all I/O)
I/O ports Hi-Z leakage current(7)
Continued on next page
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Electrical Specifications
Data Sheet
353
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
Characteristic(1)
Typ(2)
Symbol
Min
Max
Unit
Pullup/pulldown resistors (as input only)
Ports PTA7/KBD7–PTA0/KBD0, PTC6–PTC0/CANTX
,
RPU
20
45
65
kΩ
PTD7/T2CH1–PTD0/SS
COut
CIn
Capacitance
Ports (as input or output)
—
—
—
—
12
8
pF
VTST
VDD + 2.5
3.90
VDD + 4.0
4.50
Monitor mode entry voltage
—
V
V
V
VTRIPF
VTRIPR
Low-voltage inhibit, trip falling voltage
Low-voltage inhibit, trip rising voltage
Low-voltage inhibit reset/recover hysteresis
4.25
4.35
4.20
4.60
VHYS
—
100
—
mV
(VTRIPF + VHYS = VTRIPR
)
POR rearm voltage(8)
POR reset voltage(9)
VPOR
VPORRST
RPOR
0
0
—
700
—
100
800
—
mV
mV
POR rise time ramp rate(10)
0.035
V/ms
1. VDD = 5.0 Vdc ± 10%, VSS = 0 Vdc, TA = TA (min) to TA (max), unless otherwise noted
2. Typical values reflect average measurements at midpoint of voltage range, 25°C only.
3. Run (operating) IDD measured using external square wave clock source (fOSC = 32 MHz). All inputs 0.2 V from rail. No dc
loads. Less than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly
affects run IDD. Measured with all modules enabled.
4. Wait IDD measured using external square wave clock source (fOSC = 32 MHz). All inputs 0.2 V from rail. No dc loads. Less
than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects wait
IDD. Measured with CGM and LVI enabled.
5. Stop IDD is measured with OSC1 = VSS. All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. All ports
configured as inputs. Typical values at midpoint of voltage range, 25°C only.
6. Stop IDD with TBM enabled is measured using an external square wave clock source (fOSC = 32 MHz). All inputs 0.2 V
from rail. No dc loads. Less than 100 pF on all outputs. All inputs configured as inputs.
7. Pullups and pulldowns are disabled. Port B leakage is specified in 21.10 5.0-Volt ADC Characteristics.
8. Maximum is highest voltage that POR is guaranteed.
9. Maximum is highest voltage that POR is possible.
10. If minimum VDD is not reached before the internal POR reset is released, RST must be driven low externally until minimum
VDD is reached.
Data Sheet
354
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Electrical Specifications
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
3.3-Vdc Electrical Characteristics
21.6 3.3-Vdc Electrical Characteristics
Characteristic(1)
Typ(2)
Symbol
Min
Max
Unit
Output high voltage
(ILoad = –0.6 mA) all I/O pins
VOH
VOH
VOH
IOH1
VDD – 0.3
VDD – 1.0
VDD – 1.0
—
—
—
—
—
—
—
—
30
V
V
V
(ILoad = –4.0 mA) all I/O pins
(ILoad = –10.0 mA) pins PTC0–PTC4, PTF0–PTF3 only
Maximum combined IOH for port PTA7–PTA3,
mA
port PTC0–PTC1, port E, port PTD0–PTD3,
port PTF0–PTF3, port PTG4–PTG7
Maximum combined IOH for port PTA2–PTA0,
IOH2
—
—
30
60
mA
mA
—
—
port B, port PTC2–PTC6, port PTD4–PTD7
port PTF4–PTF7, port PTG0–PTG3
Maximum total IOH for all port pins
IOHT
Output low voltage
(ILoad = 0.5 mA) all I/O pins
VOL
VOL
VOL
IOL1
V
V
V
—
—
—
—
—
—
—
—
0.3
1.0
0.8
30
(ILoad = 5 mA) all I/O pins
(ILoad = 10 mA) pins PTC0–PTC4, PTF0–PTF3 only
Maximum combined IOH for port PTA7–PTA3,
mA
port PTC0–PTC1, port E, port PTD0–PTD3
port PTF0–PTF3, port PTG4–PTG7
—
—
30
Maximum combined IOH for port PTA2–PTA0,
IOL2
mA
port B, port PTC2–PTC6, port PTD4–PTD7
port PTF4–PTF7, port PTG0–PTG3
Maximum total IOL for all port pins
—
—
—
60
IOLT
VIH
VIL
mA
V
Input high voltage
All ports, IRQ, RST, OSC1
0.7 × VDD
VDD
Input low voltage
All ports, IRQ, RST, OSC1
VSS
0.3 × VDD
—
V
VDD supply current
Run(3)
Wait(4)
—
—
8
3
12
6
mA
mA
Stop(5)
IDD
25°C
—
—
—
—
—
2
12
200
30
300
—
—
—
—
—
µA
µA
µA
µA
µA
25°C with TBM enabled(6)
25°C with LVI and TBM enabled(6)
–40°C to 125°C with TBM enabled(6)
–40°C to 125°C with LVI and TBM enabled(6)
IINJ
IINJTOT
IIL
DC injection current, all ports
–2
–25
–1
—
—
—
+2
+25
+1
mA
mA
µA
Total dc current injection (sum of all I/O)
I/O ports Hi-Z leakage current(7)
Continued on next page
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Electrical Specifications
Data Sheet
355
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
Characteristic(1)
Typ(2)
Symbol
Min
Max
Unit
Pullup/pulldown resistors (as input only)
Ports PTA7/KBD7–PTA0/KBD0, PTC6–PTC0,
PTD7/T2CH1–PTD0/SS
RPU
20
45
65
kΩ
COut
CIn
Capacitance
Ports (as input or output)
—
—
—
—
12
8
pF
VTST
VDD + 2.5
2.35
VDD + 4.0
2.8
Monitor mode entry voltage
—
2.6
V
V
V
VTRIPF
VTRIPR
Low-voltage inhibit, trip falling voltage
Low-voltage inhibit, trip rising voltage
Low-voltage inhibit reset/recover hysteresis
2.4
2.66
2.9
VHYS
—
100
—
mV
(VTRIPF + VHYS = VTRIPR
)
POR rearm voltage(8)
POR reset voltage(9)
VPOR
VPORRST
RPOR
0
0
—
700
—
100
800
—
mV
mV
POR rise time ramp rate(10)
0.02
V/ms
1. VDD = 3.3 Vdc ± 10%, VSS = 0 Vdc, TA = TA (min) to TA (max), unless otherwise noted
2. Typical values reflect average measurements at midpoint of voltage range, 25°C only.
3. Run (operating) IDD measured using external square wave clock source (fOSC = 16 MHz). All inputs 0.2 V from rail. No dc
loads. Less than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly
affects run IDD. Measured with all modules enabled.
4. Wait IDD measured using external square wave clock source (fOSC = 16 MHz). All inputs 0.2 V from rail. No dc loads. Less
than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects wait
IDD. Measured with CGM and LVI enabled.
5. Stop IDD is measured with OSC1 = VSS. All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. All ports
configured as inputs. Typical values at midpoint of voltage range, 25°C only.
6. Stop IDD with TBM enabled is measured using an external square wave clock source (fOSC = 16 MHz). All inputs 0.2 V
from rail. No dc loads. Less than 100 pF on all outputs. All inputs configured as inputs.
7. Pullups and pulldowns are disabled.
8. Maximum is highest voltage that POR is guaranteed.
9. Maximum is highest voltage that POR is possible.
10. If minimum VDD is not reached before the internal POR reset is released, RST must be driven low externally until minimum
VDD is reached.
Data Sheet
356
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Electrical Specifications
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
5.0-Volt Control Timing
21.7 5.0-Volt Control Timing
Characteristic(1)
Symbol
Min
Max
Unit
Frequency of operation
Crystal option
External clock option(2)
fOSC
1
dc
8
32
MHz
fOP (fBus
tCYC
tRL
)
Internal operating frequency
Internal clock period (1/fOP
—
125
8
MHz
ns
)
—
—
—
—
RESET input pulse width low
100
ns
tILIH
IRQ interrupt pulse width low (edge-triggered)
100
ns
IRQ interrupt pulse period(3)
tILIL
tCYC
Note 3
1. VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VDD unless otherwise noted.
2. No more than 10% duty cycle deviation from 50%.
3. The minimum period is the number of cycles it takes to execute the interrupt service routine plus 1 tCYC
.
21.8 3.3-Volt Control Timing
Characteristic(1)
Symbol
Min
Max
Unit
Frequency of operation
Crystal option
External clock option(2)
fOSC
1
dc
8
16
MHz
f
OP (fBus
tCYC
tRL
)
Internal operating frequency
Internal clock period (1/fOP
—
250
4
MHz
ns
)
—
—
—
—
RESET input pulse width low
200
ns
tILIH
IRQ interrupt pulse width low (edge-triggered)
200
ns
IRQ interrupt pulse period(3)
tILIL
tCYC
Note 3
1. VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VDD unless otherwise noted.
2. No more than 10% duty cycle deviation from 50%.
3. The minimum period is the number of cycles it takes to execute the interrupt service routine plus 1 tCYC
.
tRL
RST
tILIL
tILIH
IRQ
Figure 21-1. RST and IRQ Timing
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
357
MOTOROLA
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
21.9 Clock Generation Module (CGM) Characteristics
21.9.1 CGM Component Specifications
Characteristic
Symbol
Min
1
Typ
4
Max
8
Unit
MHz
pF
fXCLK
Crystal frequency
Crystal load capacitance(1)
Crystal fixed capacitance
Crystal tuning capacitance
Feedback bias resistor
CL
C1
C2
RB
RS
—
—
—
1
20
—
(2 x CL) –5
(2 x CL) –5
47
47
20
—
pF
pF
10
0
MΩ
kΩ
Series damping resistor
—
1. Consult crystal manufacturer’s data.
21.9.2 CGM Electrical Specifications
Characteristic
Reference frequency (for PLL operation)
Range nominal multiplier
Symbol
Min
1
Typ
4
Max
8
Unit
MHz
KHz
fRCLK
fNOM
fVRS
—
71.42
—
(Lx2E)fNOM
Programmed VCO center-of-range frequency(1)
—
—
MHz
1. See 4.3.6 Programming the PLL for detailed instruction on selecting appropriate values for L and E.
Data Sheet
358
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Electrical Specifications
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
5.0-Volt ADC Characteristics
21.10 5.0-Volt ADC Characteristics
Characteristic(1)
Symbol
Min
Max
5.5
Unit
Comments
V
DDAD should be tied to
VDDAD
Supply voltage
4.5
V
the same potential as VDD
via separate traces.
VADIN
BAD
VDDAD
VADIN <= VDDAD
Input voltages
0
10
V
Bits
Resolution
10
+4
AAD
Absolute accuracy
ADC internal clock
Conversion range
Power-up time
–4
LSB
Includes quantization
fADIC
RAD
tAIC = 1/fADIC
500 k
VSSAD
1.048 M
VDDAD
Hz
V
tADPU
tADC
tADS
MAD
ZADI
FADI
CADI
IVREF
tAIC cycles
tAIC cycles
tAIC cycles
16
16
5
—
17
—
Conversion time
Sample time
Monotonicity
Guaranteed
VADIN = VSSA
ADIN = VDDA
Zero input reading
Full-scale reading
Input capacitance
VDDAD/VREFH current
000
3FC
—
003
3FF
30
Hex
Hex
pF
V
Not tested
—
1.6
mA
Absolute accuracy
(8-bit truncation mode)
AAD
—
–1
+1
LSB
LSB
Includes quantization
Quantization error
(8-bit truncation mode)
–1/8
+7/8
1. VDD = 5.0 Vdc ± 10%, VSS = 0 Vdc, VDDAD/VREFH = 5.0 Vdc ± 10%, VSSAD/VREFL = 0 Vdc
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
359
MOTOROLA
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
21.11 3.3-Volt ADC Characteristics
Characteristic(1)
Symbol
Min
Max
3.6
Unit
Comments
V
DDAD should be tied to
VDDAD
Supply voltage
3.0
V
the same potential as VDD
via separate traces.
VADIN
BAD
VDDAD
VADIN <= VDDAD
Input voltages
0
10
V
Bits
Resolution
10
+6
AAD
Absolute accuracy
ADC internal clock
Conversion range
Power-up time
–6
LSB
Includes quantization
fADIC
RAD
tAIC = 1/fADIC
500 k
VSSAD
1.048 M
VDDAD
Hz
V
tADPU
tADC
tADS
MAD
ZADI
FADI
CADI
IVREF
tAIC cycles
tAIC cycles
tAIC cycles
16
16
5
—
17
—
Conversion time
Sample time
Monotonicity
Guaranteed
VADIN = VSSA
ADIN = VDDA
Zero input reading
Full-scale reading
Input capacitance
VDDAD/VREFH current
000
3FA
—
005
3FF
30
Hex
Hex
pF
V
Not tested
—
1.2
mA
Absolute accuracy
(8-bit truncation mode)
AAD
—
–1
+1
LSB
LSB
Includes quantization
Quantization error
(8-bit truncation mode)
–1/8
+7/8
1. VDD = 3.3 Vdc ± 10%, VSS = 0 Vdc, VDDAD/VREFH = 3.3 Vdc ± 10%, VSSAD/VREFL = 0 Vdc
Data Sheet
360
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Electrical Specifications
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
5.0-Volt SPI Characteristics
21.12 5.0-Volt SPI Characteristics
Diagram
Number(1)
Characteristic(2)
Operating frequency
Symbol
Min
Max
Unit
fOP(M)
fOP(S)
fOP/2
fOP
fOP/128
dc
Master
Slave
MHz
MHz
Cycle time
Master
Slave
tCYC(M)
tCYC(S)
tCYC
tCYC
1
2
1
128
—
tLead(S)
tLag(S)
tCYC
tCYC
2
3
Enable lead time
Enable lag time
1
1
—
—
Clock (SPSCK) high time
Master
Slave
tSCKH(M)
tSCKH(S)
tCYC –25
64 tCYC
—
4
5
6
7
ns
ns
1/2 tCYC –25
Clock (SPSCK) low time
Master
Slave
tSCKL(M)
tSCKL(S)
tCYC –25
64 tCYC
—
ns
ns
1/2 tCYC –25
Data setup time (inputs)
Master
Slave
tSU(M)
tSU(S)
30
30
—
—
ns
ns
Data hold time (inputs)
Master
Slave
tH(M)
tH(S)
30
30
—
—
ns
ns
Access time, slave(3)
CPHA = 0
CPHA = 1
tA(CP0)
tA(CP1)
8
9
0
0
40
40
ns
ns
Disable time, slave(4)
tDIS(S)
—
40
ns
Data valid time, after enable edge
Master
Slave(5)
tV(M)
tV(S)
10
—
—
50
50
ns
ns
Data hold time, outputs, after enable edge
Master
Slave
tHO(M)
tHO(S)
11
0
0
—
—
ns
ns
1. Numbers refer to dimensions in Figure 21-2 and Figure 21-3.
2. All timing is shown with respect to 20% VDD and 70% VDD, unless noted; 100 pF load on all SPI pins.
3. Time to data active from high-impedance state
4. Hold time to high-impedance state
5. With 100 pF on all SPI pins
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
361
MOTOROLA
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
21.13 3.3-Volt SPI Characteristics
Diagram
Characteristic(2)
Number(1)
Symbol
Min
Max
Unit
Operating frequency
Master
Slave
fOP(M)
fOP(S)
fOP/2
fOP
fOP/128
DC
MHz
MHz
Cycle time
Master
Slave
tCYC(M)
tCYC(S)
tcyc
tcyc
1
2
1
128
—
tLead(S)
tLag(S)
tcyc
tcyc
2
3
Enable lead time
Enable lag time
1
1
—
—
Clock (SPSCK) high time
Master
Slave
tSCKH(M)
tSCKH(S)
tcyc –35
64 tcyc
—
4
5
6
7
ns
ns
1/2 tcyc –35
Clock (SPSCK) low time
Master
Slave
tSCKL(M)
tSCKL(S)
tcyc –35
64 tcyc
—
ns
ns
1/2 tcyc –35
Data setup time (inputs)
Master
Slave
tSU(M)
tSU(S)
40
40
—
—
ns
ns
Data hold time (inputs)
Master
Slave
tH(M)
tH(S)
40
40
—
—
ns
ns
Access time, slave(3)
CPHA = 0
CPHA = 1
tA(CP0)
tA(CP1)
8
9
0
0
50
50
ns
ns
Disable time, slave(4)
tDIS(S)
—
50
ns
Data valid time, after enable edge
Master
Slave(5)
tV(M)
tV(S)
10
—
—
60
60
ns
ns
Data hold time, outputs, after enable edge
Master
Slave
tHO(M)
tHO(S)
11
0
0
—
—
ns
ns
1. Numbers refer to dimensions in Figure 21-2 and Figure 21-3.
2. All timing is shown with respect to 20% VDD and 70% VDD, unless noted; 100 pF load on all SPI pins.
3. Time to data active from high-impedance state
4. Hold time to high-impedance state
5. With 100 pF on all SPI pins
Data Sheet
362
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Electrical Specifications
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
3.3-Volt SPI Characteristics
SS
INPUT
SS PIN OF MASTER HELD HIGH
1
5
SPSCK OUTPUT
CPOL = 0
NOTE
4
5
SPSCK OUTPUT
CPOL = 1
NOTE
4
6
7
MISO
INPUT
MSB IN
BITS 6–1
BITS 6–1
LSB IN
11
MASTER MSB OUT
10
11
MOSI
OUTPUT
MASTER LSB OUT
Note: This first clock edge is generated internally, but is not seen at the SPSCK pin.
a) SPI Master Timing (CPHA = 0)
SS
INPUT
SS PIN OF MASTER HELD HIGH
1
SPSCK OUTPUT
CPOL = 0
5
NOTE
4
SPSCK OUTPUT
CPOL = 1
5
NOTE
4
6
7
MISO
INPUT
MSB IN
BITS 6–1
BITS 6–1
LSB IN
11
10
10
MOSI
OUTPUT
MASTER MSB OUT
MASTER LSB OUT
Note: This last clock edge is generated internally, but is not seen at the SPSCK pin.
b) SPI Master Timing (CPHA = 1)
Figure 21-2. SPI Master Timing
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
363
MOTOROLA
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
SS
INPUT
3
1
SPSCK INPUT
CPOL = 0
5
4
2
SPSCK INPUT
CPOL = 1
5
4
9
8
MISO
INPUT
SLAVE MSB OUT
BITS 6–1
BITS 6–1
SLAVE LSB OUT
11
NOTE
11
6
7
10
MOSI
OUTPUT
MSB IN
LSB IN
Note: Not defined but normally MSB of character just received
a) SPI Slave Timing (CPHA = 0)
SS
INPUT
1
SPSCK INPUT
CPOL = 0
5
4
5
2
3
SPSCK INPUT
CPOL = 1
4
10
9
8
MISO
OUTPUT
NOTE
SLAVE MSB OUT
BITS 6–1
BITS 6–1
SLAVE LSB OUT
11
6
7
10
MOSI
INPUT
MSB IN
LSB IN
Note: Not defined but normally LSB of character previously transmitted
b) SPI Slave Timing (CPHA = 1)
Figure 21-3. SPI Slave Timing
Data Sheet
364
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Electrical Specifications
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
Timer Interface Module Characteristics
21.14 Timer Interface Module Characteristics
Characteristic
Timer input capture pulse width
Timer input capture period
Symbol
tTH, TL
Min
Max
—
Unit
t
tcyc
2
Note(1)
tcyc + 5
tTLTL
tcyc
ns
—
tTCL, tTCH
Timer input clock pulse width
—
1. The minimum period is the number of cycles it takes to execute the interrupt service routine plus 1 tcyc
.
tTLTL
tTH
INPUT CAPTURE
RISING EDGE
tTLTL
tTL
INPUT CAPTURE
FALLING EDGE
tTLTL
tTH
tTL
INPUT CAPTURE
BOTH EDGES
tTCH
TCLK
tTCL
Figure 21-4. Timer Input Timing
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Electrical Specifications
Data Sheet
365
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Electrical Specifications
21.15 Memory Characteristics
Characteristic
RAM data retention voltage
Symbol
Min
1.3
1
Typ
—
Max
—
Unit
V
VRDR
FLASH program bus clock frequency
FLASH read bus clock frequency
—
—
—
MHz
Hz
(1)
0
—
8 M
fRead
FLASH page erase time
<1 k cycles
>1 k cycles
tErase
0.9
3.6
1
4
1.1
5.5
ms
tMErase
tNVS
FLASH mass erase time
4
10
5
—
—
—
—
—
—
—
—
—
—
—
—
40
—
ms
µs
µs
µs
µs
µs
µs
FLASH PGM/ERASE to HVEN setup time
FLASH high-voltage hold time
FLASH high-voltage hold time (mass erase)
FLASH program hold time
tNVH
tNVHL
tPGS
100
5
tPROG
FLASH program time
30
1
(2)
FLASH return to read time
tRCV
(3)
FLASH cumulative program HV period
—
10 k
15
—
4
ms
tHV
FLASH endurance(4)
—
—
100 k
100
—
—
Cycles
Years
FLASH data retention time(5)
1. fRead is defined as the frequency range for which the FLASH memory can be read.
2. tRCV is defined as the time it needs before the FLASH can be read after turning off the high voltage charge pump, by
clearing HVEN to 0.
3. tHV is defined as the cumulative high voltage programming time to the same row before next erase.
tHV must satisfy this condition: tNVS + tNVH + tPGS + (tPROG x 32) ≤ tHV maximum.
4. Typical endurance was evaluated for this product family. For additional information on how Motorola defines Typical
Endurance, please refer to Engineering Bulletin EB619.
5. Typical data retention values are based on intrinsic capability of the technology measured at high temperature and de-rated
to 25°C using the Arrhenius equation. For additional information on how Motorola defines Typical Data Retention, please
refer to Engineering Bulletin EB618.
Data Sheet
366
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Electrical Specifications
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Section 22. Ordering Information and Mechanical Specifications
22.1 Introduction
This section contains ordering numbers for the MC68HC908GZ60 and gives the
dimensions for:
•
•
•
32-pin low-profile quad flat pack (case 873A)
48-pin low-profile quad flat pack (case 932-03)
64-pin quad flat pack (case 840B)
The following figures show the latest package drawings at the time of this
publication. To make sure that you have the latest package specifications, contact
your local Motorola Sales Office.
22.2 MC Order Numbers
Table 22-1. MC Order Numbers
Operating
Temperature Range
MC Order Number
MC908GZ60CFJ
Package
–40°C to +85°C
–40°C to +105°C
–40°C to +125°C
–40°C to +85°C
–40°C to +105°C
–40°C to +125°C
–40°C to +85°C
–40°C to +105°C
–40°C to +125°C
32-pin low-profile
quad flat package
(LQFP)
MC908GZ60VFJ
MC908GZ60MFJ
MC908GZ60CFA
MC908GZ60VFA
MC908GZ60MFA
MC908GZ60CFU
MC908GZ60VFU
MC908GZ60MFU
48-pin low-profile
quad flat package
(LQFP)
64-pin quad flat
package
(QFP)
Temperature designators:
C = –40°C to +85°C
V = –40°C to +105°C
M = –40°C to +125°C
M C 9 0 8 G Z X X X X X
FAMILY
PACKAGE DESIGNATOR
TEMPERATURE RANGE
Figure 22-1. Device Numbering System
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
367
MOTOROLA
Ordering Information and Mechanical Specifications
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Ordering Information and Mechanical Specifications
22.3 32-Pin Low-Profile Quad Flat Pack (LQFP)
4X
A
A1
0.20 (0.008) AB T–U
Z
32
25
1
–U–
V
–T–
B
AE
AE
P
B1
DETAIL Y
–Z–
V1
17
8
DETAIL Y
9
4X
0.20 (0.008) AC T–U
Z
9
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
S1
S
2. CONTROLLING DIMENSION: MILLIMETER.
3. DATUM PLANE –AB– IS LOCATED AT BOTTOM
OF LEAD AND IS COINCIDENT WITH THE LEAD
WHERE THE LEAD EXITS THE PLASTIC BODY AT
THE BOTTOM OF THE PARTING LINE.
4. DATUMS –T–, –U–, AND –Z– TO BE DETERMINED
AT DATUM PLANE –AB–.
DETAIL AD
G
5. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE –AC–.
–AB–
–AC–
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS
0.250 (0.010) PER SIDE. DIMENSIONS A AND B
DO INCLUDE MOLD MISMATCH AND ARE
DETERMINED AT DATUM PLANE –AB–.
7. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. DAMBAR PROTRUSION SHALL
NOT CAUSE THE D DIMENSION TO EXCEED
0.520 (0.020).
SEATING
PLANE
0.10 (0.004) AC
BASE
METAL
N
8. MINIMUM SOLDER PLATE THICKNESS SHALL BE
0.0076 (0.0003).
9. EXACT SHAPE OF EACH CORNER MAY VARY
FROM DEPICTION.
F
D
8X M
MILLIMETERS
DIM MIN MAX
7.000 BSC
INCHES
MIN MAX
0.276 BSC
0.138 BSC
0.276 BSC
0.138 BSC
R
J
A
A1
B
3.500 BSC
7.000 BSC
3.500 BSC
SECTION AE–AE
E
C
B1
C
1.400
1.600
0.450
1.450
0.400
0.055
0.063
0.018
0.057
0.016
D
E
F
0.300
1.350
0.300
0.012
0.053
0.012
W
G
H
J
0.800 BSC
0.031 BSC
Q
H
K
X
0.050
0.090
0.500
0.150
0.200
0.700
0.002
0.004
0.020
0.006
0.008
0.028
K
M
N
P
12 REF
12 REF
DETAIL AD
0.090
0.160
0.004
0.006
0.400 BSC
0.016 BSC
Q
R
1
0.150
5
0.250
1
0.006
5
0.010
S
9.000 BSC
0.354 BSC
S1
V
V1
W
X
4.500 BSC
9.000 BSC
4.500 BSC
0.200 REF
1.000 REF
0.177 BSC
0.354 BSC
0.177 BSC
0.008 REF
0.039 REF
Data Sheet
368
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Ordering Information and Mechanical Specifications
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Ordering Information and Mechanical Specifications
48-Pin Low-Profile Quad Flat Pack (LQFP)
22.4 48-Pin Low-Profile Quad Flat Pack (LQFP)
4X
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
0.200 AB T-U
Z
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETER.
DETAIL Y
9
A
3. DATUM PLANE AB IS LOCATED AT BOTTOM OF LEAD
AND IS COINCIDENT WITH THE LEAD WHERE THE
LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF
THE PARTING LINE.
P
A1
48
37
4. DATUMS T, U, AND Z TO BE DETERMINED AT DATUM
PLANE AB.
5. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE AC.
1
36
T
U
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.250
PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD
MISMATCH AND ARE DETERMINED AT DATUM PLANE
AB.
B
V
AE
AE
7. DIMENSION D DOES NOT INCLUDE DAMBAR
B1
PROTRUSION. DAMBAR PROTRUSION SHALL NOT
CAUSE THE D DIMENSION TO EXCEED 0.350.
V1
12
25
8. MINIMUM SOLDER PLATE THICKNESS SHALL BE
MILLIMETERS
13
24
DIM MIN
MAX
7.000 BSC
3.500 BSC
Z
A
A1
B
B1
C
S1
7.000 BSC
3.500 BSC
T, U, Z
1.400
1.600
0.270
1.450
0.230
S
D
E
F
0.170
1.350
0.170
DETAIL Y
4X
0.200 AC T-U
Z
G
H
J
K
L
M
N
P
0.500 BSC
0.050
0.090
0.500
0
0.150
0.200
0.700
7
×
×
0.080 AC
12 REF
×
G
AB
AC
0.090
0.250 BSC
0.150 0.250
0.160
R
S
S1
V
V1
W
AA
9.000 BSC
4.500 BSC
9.000 BSC
4.500 BSC
0.200 REF
1.000 REF
AD
°
M
BASE METAL
TOP & BOTTOM
R
N
J
E
C
H
F
D
M
0.080
AC T-U Z
SECTION AE-AE
W
°
L
K
DETAIL AD
AA
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MOTOROLA Ordering Information and Mechanical Specifications
Data Sheet
369
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Ordering Information and Mechanical Specifications
22.5 64-Pin Quad Flat Pack (QFP)
L
48
33
49
32
B
B
P
–A–
L
–B–
V
B
–A–, –B–, –D–
DETAIL A
DETAIL A
F
64
17
1
16
–D–
A
M
S
S
S
S
0.20 (0.008)
C
A–B
D
J
N
0.05 (0.002) A–B
S
BASE
M
0.20 (0.008)
H
A–B
D
METAL
E
D
DETAILC
M
M
S
S
D
0.02 (0.008)
C
A–B
DATUM
PLANE
C
–H–
–C–
SEATING
PLANE
0.01 (0.004)
M
H
G
U
NOTES:
MILLIMETERS
INCHES
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
DIM MIN
MAX
14.10
14.10
2.45
MIN
MAX
0.555
0.555
0.096
0.018
0.094
0.016
A
B
13.90
13.90
2.15
0.30
2.00
0.30
0.547
0.547
0.085
0.012
0.079
0.012
T
3. DATUM PLANE –H– IS LOCATED AT BOTTOM OF
LEAD AND IS COINCIDENT WITH THE LEAD
WHERE THE LEAD EXITS THE PLASTIC BODY AT
THE BOTTOM OF THE PARTING LINE.
4. DATUMS –A–, –B– AND –D– TO BE DETERMINED
AT DATUM PLANE –H–.
C
D
E
F
0.45
2.40
R
0.40
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
0.80 BSC
0.031 BSC
5. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE –C–.
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25
(0.010) PER SIDE. DIMENSIONS A AND B DO
INCLUDE MOLD MISMATCH AND ARE
DETERMINED AT DATUM PLANE –H–.
7. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) PER SIDE.
TOTAL IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION. DAMBAR
CANNOT BE LOCATED ON THE LOWER RADIUS
OR THE FOOT.
DATUM
PLANE
–H–
–––
0.13
0.65
0.25
0.23
0.95
–––
0.005
0.026
0.010
0.009
0.037
Q
12.00 REF
0.472 REF
5
0.13
10
0.17
5
0.005
10
0.007
K
0.40 BSC
0.016 BSC
0
0
0.13
16.95
0.13
0
7
0.30
17.45
–––
7
W
0.005
0.667
0.005
0
0.012
0.687
–––
X
–––
17.45
0.45
–––
0.687
0.018
DETAIL C
16.95
0.35
0.667
0.014
1.6 REF
0.063 REF
Data Sheet
370
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Ordering Information and Mechanical Specifications
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Appendix A. MC68HC908GZ48
A.1 Introduction
The MC68HC908GZ48 is a member of the low-cost, high-performance M68HC08
Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the
enhanced M68HC08 central processor unit (CPU08) and are available with a
variety of modules, memory sizes and types, and package types.
The information contained in this document pertains to the MC68HC908GZ48 with
the exceptions shown in this appendix.
A.2 Block Diagram
See Figure A-1.
A.3 Memory
The MC68HC908GZ48 can address 48 Kbytes of memory space. The memory
map, shown in Figure A-2, includes:
•
•
•
48 Kbytes of user FLASH memory
1536 bytes of random-access memory (RAM)
52 bytes of user-defined vectors
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
371
MOTOROLA
MC68HC908GZ48
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC68HC908GZ48
B
P O R T
D D R B
P O R T F
D D R F
G T P O R
D D R G
A T P O R
D D R A
C
P O R T
D D R C
P O R T E
D D R E
P O R T D
D D R D
Data Sheet
372
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MC68HC908GZ48 MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC68HC908GZ48
$FE00
$FE01
$FE02
$FE03
$FE04
$FE05
$FE06
$FE07
$FE08
$FE09
$FE0A
$FE0B
$FE0C
$FE0D
$FE0E
$FE0F
SIM BREAK STATUS REGISTER (BSR)
SIM RESET STATUS REGISTER (SRSR)
$0000
↓
I/O REGISTERS
64 BYTES
$003F
RESERVED
SIM BREAK FLAG CONTROL REGISTER (BFCR)
INTERRUPT STATUS REGISTER 1 (INT1)
INTERRUPT STATUS REGISTER 2 (INT2)
INTERRUPT STATUS REGISTER 3 (INT3)
INTERRUPT STATUS REGISTER 4 (INT4)
FLASH-2 CONTROL REGISTER (FL2CR)
BREAK ADDRESS REGISTER HIGH (BRKH)
BREAK ADDRESS REGISTER LOW (BRKL)
BREAK STATUS AND CONTROL REGISTER (BRKSCR)
LVI STATUS REGISTER (LVISR)
$0040
↓
RAM-1
1024 BYTES
$043F
$0440
↓
I/O REGISTERS
34 BYTES
$0461
$0462
↓
RESERVED
$04FF
$0500
↓
MSCAN CONTROL AND MESSAGE BUFFER
128 BYTES
FLASH-2 TEST CONTROL REGISTER (FLTCR2)
FLASH-1 TEST CONTROL REGISTER (FLTCR1)
UNIMPLEMENTED
$057F
$0580
↓
RAM-2
512 BYTES
UNIMPLEMENTED
16 BYTES
$FE10
↓
$077F
RESERVED FOR COMPATIBILITY WITH MONITOR CODE
FOR A-FAMILY PART
$FE1F
$0780
↓
RESERVED
$FE20
↓
MONITOR ROM
352 BYTES
$1DFF
$FF7F
$1E00
↓
MONITOR ROM
16 BYTES
$FF80
$FF81
FLASH-1 BLOCK PROTECT REGISTER (FL1BPR)
FLASH-2 BLOCK PROTECT REGISTER (FL2BPR)
$1E0F
$1E10
↓
$FF82
↓
RESERVED
RESERVED
FLASH-1 CONTROL REGISTER (FL1CR)
RESERVED
$3FFF
$FF87
$FF88
$4000
↓
FLASH-2
16,384 BYTES
$FF89
↓
$7FFF
$FFCB
$8000
↓
$FFCC
↓
$FFFF(1)
FLASH-1
32,256 BYTES
FLASH-1 VECTORS
52 BYTES
$FDFF
1. $FFF6–$FFFD used for eight security bytes
Figure A-2. MC68HC908GZ48 Memory Map
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
373
MOTOROLA
MC68HC908GZ48
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC68HC908GZ48
A.4 Ordering Information
Table A-1. MC Order Numbers
Operating
MC Order Number
Package
Temperature Range
MC908GZ48CFJ
MC908GZ48VFJ
–40°C to +85°C
–40°C to +105°C
–40°C to +125°C
–40°C to +85°C
–40°C to +105°C
–40°C to +125°C
–40°C to +85°C
–40°C to +105°C
–40°C to +125°C
32-pin low-profile
quad flat package
(LQFP)
MC908GZ48MFJ
MC908GZ48CFA
MC908GZ48VFA
MC908GZ48MFA
MC908GZ48CFU
MC908GZ48VFU
MC908GZ48MFU
48-pin low-profile
quad flat package
(LQFP)
64-pin quad flat
package
(QFP)
Temperature designators:
C = –40°C to +85°C
V = –40°C to +105°C
M = –40°C to +125°C
M C 9 0 8 G Z X X X X X
FAMILY
PACKAGE DESIGNATOR
TEMPERATURE RANGE
Figure A-3. Device Numbering System
Data Sheet
374
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MC68HC908GZ48
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ60
Appendix B. MC68HC908GZ32
B.1 Introduction
The MC68HC908GZ32 is a member of the low-cost, high-performance M68HC08
Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the
enhanced M68HC08 central processor unit (CPU08) and are available with a
variety of modules, memory sizes and types, and package types.
The information contained in this document pertains to the MC68HC908GZ32 with
the exceptions shown in this appendix.
B.2 Block Diagram
See Figure B-1.
B.3 Memory
The MC68HC908GZ32 can address 32 Kbytes of memory space. The memory
map, shown in Figure B-2, includes:
•
•
•
32 Kbytes of user FLASH memory
1536 bytes of random-access memory (RAM)
52 bytes of user-defined vectors
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
375
MOTOROLA
MC68HC908GZ32
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC68HC908GZ32
B
P O R T
D D R B
P O R T F
D D R F
G T P O R
D D R G
A T P O R
D D R A
C
P O R T
D D R C
P O R T E
D D R E
P O R T D
D D R D
Data Sheet
376
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MC68HC908GZ32 MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC68HC908GZ32
$FE00
$FE01
$FE02
$FE03
$FE04
$FE05
$FE06
$FE07
$FE08
$FE09
$FE0A
$FE0B
$FE0C
$FE0D
$FE0E
$FE0F
SIM BREAK STATUS REGISTER (BSR)
SIM RESET STATUS REGISTER (SRSR)
$0000
↓
I/O REGISTERS
64 BYTES
$003F
RESERVED
SIM BREAK FLAG CONTROL REGISTER (BFCR)
INTERRUPT STATUS REGISTER 1 (INT1)
INTERRUPT STATUS REGISTER 2 (INT2)
INTERRUPT STATUS REGISTER 3 (INT3)
INTERRUPT STATUS REGISTER 4 (INT4)
UNIMPLEMENTED
$0040
↓
RAM-1
1024 BYTES
$043F
$0440
↓
I/O REGISTERS
34 BYTES
$0461
BREAK ADDRESS REGISTER HIGH (BRKH)
BREAK ADDRESS REGISTER LOW (BRKL)
BREAK STATUS AND CONTROL REGISTER (BRKSCR)
LVI STATUS REGISTER (LVISR)
$0462
↓
RESERVED
$04FF
$0500
↓
MSCAN CONTROL AND MESSAGE BUFFER
128 BYTES
UNIMPLEMENTED
$057F
FLASH-1 TEST CONTROL REGISTER (FLTCR1)
UNIMPLEMENTED
$0580
↓
RAM-2
512 BYTES
UNIMPLEMENTED
16 BYTES
$FE10
↓
$FE1F
$077F
RESERVED FOR COMPATIBILITY WITH MONITOR CODE
FOR A-FAMILY PART
$0780
↓
RESERVED
$FE20
↓
$FF7F
MONITOR ROM
352 BYTES
$1DFF
$1E00
↓
MONITOR ROM
16 BYTES
$FF80
FLASH-1 BLOCK PROTECT REGISTER (FL1BPR)
RESERVED
$1E0F
$FF81
↓
$FF87
$1E10
↓
RESERVED
$FF88
FLASH-1 CONTROL REGISTER (FL1CR)
RESERVED
$7FFF
$FF89
↓
$FFCB
$8000
↓
FLASH-1
32,256 BYTES
$FFCC
↓
$FFFF(1)
FLASH-1 VECTORS
52 BYTES
$FDFF
1. $FFF6–$FFFD used for eight security bytes
Figure B-2. MC68HC908GZ32 Memory Map
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
Data Sheet
377
MOTOROLA
MC68HC908GZ32
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC68HC908GZ32
B.4 Ordering Information
Table B-1. MC Order Numbers
Operating
MC Order Number
Package
Temperature Range
MC908GZ32CFJ
MC908GZ32VFJ
–40°C to +85°C
–40°C to +105°C
–40°C to +125°C
–40°C to +85°C
–40°C to +105°C
–40°C to +125°C
–40°C to +85°C
–40°C to +105°C
–40°C to +125°C
32-pin low-profile
quad flat package
(LQFP)
MC908GZ32MFJ
MC908GZ32CFA
MC908GZ32VFA
MC908GZ32MFA
MC908GZ32CFU
MC908GZ32VFU
MC908GZ32MFU
48-pin low-profile
quad flat package
(LQFP)
64-pin quad flat
package
(QFP)
Temperature designators:
C = –40°C to +85°C
V = –40°C to +105°C
M = –40°C to +125°C
M C 9 0 8 G Z X X X X X
FAMILY
PACKAGE DESIGNATOR
TEMPERATURE RANGE
Figure B-3. Device Numbering System
Data Sheet
378
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 — Rev. 1.0
MC68HC908GZ32
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
HOW TO REACH US:
USA/EUROPE/LOCATIONS NOT LISTED:
Motorola Literature Distribution
P.O. Box 5405
Denver, Colorado 80217
1-800-521-6274 or 480-768-2130
JAPAN:
Motorola Japan Ltd.
SPS, Technical Information Center
3-20-1, Minami-Azabu, Minato-ku
Tokyo 106-8573, Japan
81-3-3440-3569
ASIA/PACIFIC:
Motorola Semiconductors H.K. Ltd.
Silicon Harbour Centre
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
852-26668334
HOME PAGE:
http://motorola.com/semiconductors
Information in this document is provided solely to enable system and software implementers to use Motorola products.
There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or
integrated circuits based on the information in this document.
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty,
representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume
any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts.
Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed,
intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a
situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising
out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even
if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
MOTOROLA and the Stylized M Logo are registered in the US Patent and Trademark Office. All other product or service
names are the property of their respective owners. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
© Motorola Inc. 2004
MC68HC908GZ60/D
Rev. 1
5/2004
For More Information On This Product,
Go to: www.freescale.com
相关型号:
©2020 ICPDF网 联系我们和版权申明