MOC2A60-5F [MOTOROLA]
暂无描述;
| 型号： | MOC2A60-5F |
| 厂家： | 
MOTOROLA |
| 描述： | 暂无描述 可控硅 光电 继电器 固态继电器 输出元件 |
| 文件： | 总8页 (文件大小：124K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Order this document
by MOC2A60–10/D
SEMICONDUCTOR TECHNICAL DATA
2 Amp Zero–Cross Triac Output
This device consists of a gallium arsenide infrared emitting diode optically
coupled to a zero–cross triac driver circuit and a power triac. It is capable of
driving a load of up to 2 amps (rms) directly, on line voltages from 20 to 280 volts
ac (rms).
*Motorola Preferred Device
•
•
•
•
•
•
Provides Normally Open Solid State AC Output with 2 Amp Rating
70 Amp Single Cycle Surge Capability
OPTOISOLATOR
2 AMP ZERO CROSS
TRIAC OUTPUT
600 VOLTS
Zero–Voltage Turn–on and Zero–Current Turn–off
High Input–Output Isolation of 3750 vac (rms)
Static dv/dt Rating of 400 Volts/µs Guaranteed
2 Amp Pilot Duty Rating Per UL508 117 (Overload Test)
and 118 (Endurance Test)
[File No. 129224]
•
•
•
CSA Approved [File No. CA77170–1].
SEMKO Approved Certificate #9507228
CASE 417–02
Style 2
PLASTIC PACKAGE
Exceeds NEMA 2–230 and IEEE472 Noise Immunity Test Requirements (See Fig.14)
9
7
3
2
DEVICE RATINGS (T = 25°C unless otherwise noted)
A
Rating
INPUT LED
Symbol
Value
Unit
CASE 417A–02
Style 1
PLASTIC PACKAGE
Forward Current — Maximum Continuous
I
50
mA
A
F
Forward Current — Maximum Peak
I (pk)
F
1.0
(PW = 100µs, 120 pps)
Reverse Voltage — Maximum
V
R
6.0
V
OUTPUT TRIAC
(1)
Output Terminal Voltage — Maximum Transient
V
DRM
600
V(pk)
CASE 417B–01
Style 1
PLASTIC PACKAGE
Operating Voltage Range — Maximum Continuous
(f = 47 – 63 Hz)
V
T
20 to 280
Vac(rms)
On–State Current Range
(Free Air, Power Factor ≥ 0.3)
I (rms)
T
0.03 to 2.0
70
A
A
Non–Repetitive Single Cycle Surge Current —
Maximum Peak (t = 16.7 ms)
I
DEVICE SCHEMATIC
TSM
2
2
7
Main Terminal Fusing Current (t = 8.3 ms)
Load Power Factor Range
Junction Temperature Range
TOTAL DEVICE
I T
26
A sec
PF
0.3 to 1.0
– 40 to 125
—
3
2
T
J
°C
ZVA
(2)
*
Input–Output Isolation Voltage — Maximum
V
R
3750
8.0
Vac(rms)
ISO
47 – 63 Hz, 1 sec Duration
9
Thermal Resistance — Power Triac Junction to Case
(See Fig. 15)
°C/W
θJC
* Zero Voltage Activate Circuit
Ambient Operating Temperature Range
Storage Temperature Range
T
– 40 to +100
– 40 to +150
260
°C
°C
°C
oper
T
1, 4, 5, 6, 8. NO PIN
2. LED CATHODE
3. LED ANODE
stg
Lead Soldering Temperature — Maximum
T
L
(1/16″ from Case, 10 sec Duration)
7. MAIN TERMINAL 2
9. MAIN TERMINAL 1
1. Test voltages must be applied within dv/dt rating.
2. Input–Output isolation voltage, V
2. test, pins 2, 3 and the heat tab are common, and pins 7 and 9 are common.
, is an internal device dielectric breakdown rating. For this
ISO
POWER OPTO is a trademark of Motorola, Inc.
Preferred devices are Motorola recommended choices for future use and best overall value.
REV 2
Motorola, Inc. 1995
ELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise noted)
A
Characteristic
INPUT LED
Symbol
Min
Typ
Max
Unit
Forward Voltage (I = 10 mA)
V
1.00
—
1.17
1.0
18
1.50
100
—
V
F
F
Reverse Leakage Current (V = 6.0 V)
R
I
R
µA
pF
Capacitance
C
—
OUTPUT TRIAC
Off–State Leakage, Either Direction
I
—
400
—
0.25
—
10
—
—
µA
V/µs
mA
DRM
(I = 0, V
F DRM
= 600 V)
Critical Rate of Rise of Off–State Voltage (Static)
(1)(2)
dv/dt(s)
V
in
= 400 vac(pk))
Holding Current, Either Direction (I = 0, V = 12 V, I = 200 mA)
I
H
10
F
D
T
COUPLED
LED Trigger Current Required to Latch Output
Either Direction (Main Terminal Voltage = 2.0 V)
MOC2A60–10
MOC2A60–5
I (on)
FT
I (on)
FT
—
—
7.0
3.5
10
5.0
mA
mA
(3)(4)
On–State Voltage, Either Direction (I = Rated I (on), I
FT TM
= 2.0 A)
V
—
—
0.96
8.0
1.3
10
V
V
F
TM
(5)
Inhibit Voltage, Either Direction (I = Rated I (on))
FT
V
INH
F
(Main Terminal Voltage above which device will not trigger)
Commutating dv/dt (Rated V , I = 30 mA – 2.0 A(rms),
T
A
dv/dt (c)
5.0
—
—
V/µS
DRM
(2)
= – 40 ± 100°C, f = 60 Hz)
T
(2)
Common–mode Input–Output dv/dt
Input–Output Capacitance (V = 0, f = 1.0 MHz)
Isolation Resistance (V = 500 V)
dv/dt(cm)
—
—
40,000
1.3
—
—
—
V/µS
pF
C
R
ISO
ISO
1012
1014
Ω
I–O
1. Per EIA/NARM standard RS–443, with V = 200 V, which is the instantaneous peak of the maximum operating voltage.
P
2. Additional dv/dt information, including test methods, can be found in Motorola applications note AN1048/D, Figure 43.
3. All devices are guaranteed to trigger at an I value less than or equal to the max I . Therefore, the recommended operating I lies between
F
FT
F
3. the device’s maximum I (on) limit and the Maximum Rating of 50 mA.
FT
4. Current–limiting resistor required in series with LED.
5. Also known as “Zero Voltage Turn–On.”
TYPICAL CHARACTERISTICS
100
80
2.00
1.80
PULSE ONLY
PULSE OR DC
1.60
1.40
60
40
20
0
T
= –40°C
A
1.20
1.00
0.80
25
°C
100°C
–40
–20
0
20
40
60
80
C)
100
120
1
10
100
1000
T , AMBIENT TEMPERATURE (
°
I , FORWARD CURRENT (mA)
A
F
Figure 1. Maximum Allowable Forward LED
Current versus Ambient Temperature
Figure 2. LED Forward Voltage
versus LED Forward Current
2
Motorola Optoelectronics Device Data
1.60
1.50
1.40
1.30
1.20
1.10
1.00
0.90
0.80
2.4
2.0
1.6
WORST CASE UNIT
NORMALIZED TO
T
= 25°C
A
1.2
0.8
0.4
0.0
–40
–20
0
20
40
60
80
C)
100
120
–40
–20
0
20
40
60
80
C)
100
120
T , AMBIENT TEMPERATURE (
°
T , AMBIENT TEMPERATURE (
°
A
A
Figure 3. Forward LED Trigger Current
versus Ambient Temperature
Figure 4. Maximum Allowable On–State RMS Output
Current (Free Air) versus Ambient Temperature
2.20
2.00
1.80
1.60
1.40
1.20
1.00
0.80
0.60
2.5
PULSE ONLY
PULSE OR DC
2.0
1.5
1.0
0.5
0.0
MAXIMUM
MEAN
T
= 25°C
J
100°C
0.03
0.1
1.0
10
0.01
0.1
1.0
I
, INSTANTANEOUS ON–STATE CURRENT (A)
I , MAIN TERMINAL CURRENT (A)
T
TM
Figure 5. On–State Voltage Drop versus
Output Terminal Current
Figure 6. Power Dissipation
versus Main Terminal Current
100
10
120
100
T
= 25°C
A
NORMALIZED TO
= 25
T
°C
A
80
60
40
20
0
1.0
0.1
0.01
– 40
10
0.01
0.1
1
– 20
0
20
40
60
80
C)
100
120
I , MAIN TERMINAL CURRENT (A)
T , AMBIENT TEMPERATURE (
°
T
A
Figure 7. Junction Temperature versus Main
Terminal RMS Current (Free Air)
Figure 8. Leakage with LED Off versus
Ambient Temperature
Motorola Optoelectronics Device Data
3
2.00
1.80
1.60
1.40
1.20
1.00
0.80
0.60
0.40
0.20
0.00
1000
100
STATIC
NORMALIZED TO
= 25
T
°C
A
COMMUTATING
10
0
I
= 30 mA – 2A(RMS)
F = 60 Hz
T
– 40
– 20
0
20
40
60
80
C)
100
120
– 40
– 20
0
+ 25
+ 40
+ 60
C)
+ 80
+ 100
T , AMBIENT TEMPERATURE (
°
T , AMBIENT TEMPERATURE (
°
A
A
Figure 9. Holding Current versus
Ambient Temperature
Figure 10. dv/dt versus Ambient Temperature
LED INPUT
VOLTAGE
PIN 7 TO 9
TURN ON
POINTS
Figure 11. Operating Waveforms
Select the value of R1 according to the following formulas:
[1] R1 = (V – V ) / Max. I (on) per spec.
MOC2A60
CC
[2] R1 = (V
F
FT
V
– V ) / 0.050
CC
CC
F
R2
C1
MOV
Typical values for C1 and R2 are 0.01 µF and 39 Ω, respec-
tively. You may adjust these values for specific applications.
The maximum recommended value of C1 is 0.022 µF. See
application note AN1048 for additional information on com-
ponent values.
R1
ZVA
*
LOAD
The MOV may or may not be needed depending upon the
characteristics of the applied ac line voltage. For applica-
tions where line spikes may exceed the 600 V rating of the
MOC2A60, an MOV is required.
*ZERO VOLTAGE ACTIVATE CIRCUIT
Figure 12. Typical Application Circuit
4
Motorola Optoelectronics Device Data
Use care to maintain the minimum spacings as shown.
Safety and regulatory requirements dictate a minimum
of 8.0 mm between the closest points between input
and output conducting paths, Pins 3 and 7. Also, 0.070
inches distance is required between the two output
Pins, 7 and 9.
0.070″ MIN
Keep pad sizes on Pins 7 and 9 as large as possible
for optimal performance.
0.315″ MIN
[8 MM MIN]
Figure 13. PC Board Layout Recommendations
DEVICE UNDER TEST
NOISE
SOURCE
Each device, when installed in the circuit shown
in Figure 14, shall be capable of passing the fol-
lowing conducted noise tests:
2
3
7
9
AC
SUPPLY
•
•
•
•
IEEE 472 (2.5 KV)
Lamp Dimmer (NEMA Part DC33, 3.4.2.1)
NEMA ICS 2–230.45 Showering Arc
MIL–STD–461A CS01, CS02 and CS06
10Ω
MOV
150V
I
= RATED I
0.022µF
F
F
Z LOAD
Figure 14. Test Circuit for Conducted Noise Tests
NO ADDITIONAL HEATSINK
T
T
T
A
J
C
R
R
θCA
JUNCTION
TEMPERATURE OF
MOC2A60 . . .
θ
JC
AMBIENT AIR
TEMPERATURE
HEAT FLOW
{
}
WITH ADDITIONAL HEATSINK
OUTPUT CHIP
T
T
T
T
A
J
C
S
R
R
R
θSA
θ
JC
θ
CS
Terms in the model signify:
T = Ambient temperature
A
R
R
R
R
= Thermal resistance, heat sink to ambient
= Thermal resistance, case to ambient
= Thermal resistance, heat sink to case
= Thermal resistance, junction to case
θSA
θCA
θCS
θJC
T
T
T
T
= Optional additional
S
S
C
J
= heat sink temperature
= Case temperature
= Junction temperature
= Power dissipation
Thermal measurements of R
θJC
are referenced to the point on
the heat tab indicated with an
‘X’. Measurements should be
taken with device orientated
along its vertical axis.
P
D
Values for thermal resistance components are: R
Values for thermal resistance components are: R
The design of any additional heatsink will determine the values of R
= 36°C/W/in maximum
= 8.0°C/W maximum
θCA
θJC
and R .
θSA
θCS
T
T
– T = P (R
)
C
C
A
D
θCA
) + R
– T = P (R
), where P = Power Dissipation in Watts.
A
D
θJC
θSA
D
Figure 15. Approximate Thermal Circuit Model
Motorola Optoelectronics Device Data
5
PACKAGE DIMENSIONS
C
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
–A–
E
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
INCHES
MILLIMETERS
DIM
A
B
C
D
E
MIN
MAX
1.005
0.436
0.190
0.035
0.060
MIN
24.51
10.57
4.32
0.64
1.02
MAX
25.53
11.07
4.83
0.89
1.52
0.965
0.416
0.170
0.025
0.040
S
–B–
N
P
2
3
7
9
G
H
J
K
L
N
P
S
0.400 BSC
10.16 BSC
–T–
SEATING
PLANE
0.040
0.012
0.134
0.060
0.018
0.154
1.02
0.30
3.40
1.52
0.46
3.91
K
0.200 BSC
5.08 BSC
V
L
J
0.190
0.023
0.695
0.210
0.043
0.715
4.83
0.58
5.33
1.09
G
H
17.65
18.16
V
0.100 BSC
2.54 BSC
D 4 PL
M
M
M
0.13 (0.005)
T
A
B
STYLE 2:
PIN 2. LED CATHODE
3. LED ANODE
7. TRIAC MT
9. TRIAC MT
CASE 417–02
PLASTIC
STANDARD HEAT TAB
ISSUE C
ORDER “F” SUFFIX
HEAT TAB OPTION
(EX: MOC2A60–10F)
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
INCHES
MILLIMETERS
–A–
U
C
DIM
A
B
C
D
E
MIN
MAX
1.005
0.436
0.190
0.035
0.060
MIN
24.51
10.57
4.32
MAX
25.53
11.07
4.83
0.965
0.416
0.170
0.025
0.040
E
W
Z RADIUS
Y
0.64
0.89
Q
1.02
1.52
G
H
J
K
L
0.400 BSC
10.16 BSC
X
0.040
0.012
0.134
0.060
0.018
0.154
1.02
0.30
3.40
1.52
0.46
3.91
0.200 BSC
5.08 BSC
S
R
N
P
Q
R
S
0.190
0.023
0.057
0.734
0.840
0.593
0.210
0.043
0.067
0.754
0.870
0.613
4.83
0.58
1.45
18.64
21.34
15.06
5.33
1.09
1.70
19.15
22.10
15.57
–B–
P
2
3
7
9
N
U
V
–T–
0.100 BSC
2.54 BSC
SEATING
PLANE
W
X
Y
0.074
0.265
0.079
0.026
0.094
0.295
0.089
0.036
1.88
6.73
2.01
0.66
2.39
7.49
2.26
0.91
K
J
V
G
L
H
Z
D 4 PL
0.13 (0.005)
M
M
M
T
A
B
STYLE 1:
PIN 2. LED CATHODE
3. LED ANODE
7. TRIAC MT
9. TRIAC MT
CASE 417A–02
PLASTIC
FLUSH MOUNT HEAT TAB
ISSUE A
6
Motorola Optoelectronics Device Data
PACKAGE DIMENSIONS — CONTINUED
ORDER “C” SUFFIX
HEAT TAB OPTION
(EX: MOC2A60–10C)
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
C
–A–
INCHES
MILLIMETERS
E
DIM
A
B
C
D
E
G
H
J
K
L
N
P
MIN
MAX
1.005
0.436
0.190
0.035
0.060
MIN
24.51
10.57
4.32
MAX
25.53
11.07
4.83
0.965
0.416
0.170
0.025
0.040
–B–
S
P
0.64
0.89
1.02
1.52
N
2
3
7
9
0.400 BSC
10.16 BSC
0.040
0.012
0.134
0.060
0.060
0.154
1.02
0.30
3.40
1.52
0.46
3.91
–T–
K
SEATING
PLANE
V
0.200 BSC
5.08 BSC
L
J
0.190
0.023
0.439
0.210
0.043
0.529
4.83
0.58
5.33
1.09
H
G
S
11.15
13.44
V
0.100 BSC
2.54 BSC
D 4 PL
M
M
M
0.13 (0.005)
T
A
B
STYLE 1:
PIN 2. LED CATHODE
3. LED ANODE
7. TRIAC MT
9. TRIAC MT
CASE 417B–01
PLASTIC
CUT HEAT TAB
ISSUE O
Motorola Optoelectronics Device Data
7
Motorolareserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representationorguaranteeregarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
andspecifically disclaims any and all liability, includingwithoutlimitationconsequentialorincidentaldamages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintendedor unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA / EUROPE: Motorola Literature Distribution;
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE (602) 244–6609
INTERNET: http://Design–NET.com
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MOC2A60–10/D
◊
相关型号：
©2020 ICPDF网 联系我们和版权申明