D102ED [MPD]
Very Low Cost, 1W SIP Dual Isolated Output DC/DC Converters; 非常低的成本, 1W SIP双隔离输出DC / DC转换器型号: | D102ED |
厂家: | MICROPOWER DIRECT, LLC |
描述: | Very Low Cost, 1W SIP Dual Isolated Output DC/DC Converters |
文件: | 总2页 (文件大小:203K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
D100ED Series
Very Low Cost, 1W SIP
Dual Isolated Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Key Features:
Parameter
Conditions
Min.
Typ.
5.0
Max.
5.5
Units
5 VDC Input
4.5
• 1W Output Power
• Miniature SIP Case
• UL Approved (File E245422)
• Dual Isolated Outputs
• 1,000 VDC Isolation
• >3.5 MHour MTBF
• 12 Standard Models
• Industry Standard Pin-Out
• LOWEST COST!!
Input Voltage Range
12 VDC Input 10.8
24 VDC Input 21.6
Internal Capacitor
12.0
24.0
13.2
26.4
VDC
Input Filter
Reverse Polarity Input Current
0.3
A
Output
Parameter
Conditions
Min.
Typ.
3.0
1.2
15.0
50
Max.
Units
%
Output Voltage Accuracy
Line Regulation
3.0
For Vin Change of 1%
Iout = 10% to 100%
See Note 2
%
Load Regulation
Ripple (20 MHz)
Noise (20 MHz)
75
mV P - P
mV P - P
%
See Note 2
75
150
Output Power Protection
Temperature Coefficient
Output Short Circuit
General
120
0.03
%/ºC
Momentary (0.5 Sec.)
Parameter
Conditions
Min.
60 Seconds 1,000
1,000
Typ.
Max.
Units
VDC
VDC
MΩ
pF
RoHS Compliant
Isolation Voltage, Input/Output
Isolation Voltage, Output/Output
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Parameter
500 VDC 1,000
100 kHz, 1V
60
100
kHz
Conditions
Min.
Typ.
Max.
+85
Units
ºC
Operating Temperature Range
Storage Temperature Range
Cooling
Ambient
-40
-55
+25
+125
ºC
Free Air Convection
RH, Non-condensing
Humidity
95
%
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Physical
Case Size
0.77 x 0.24 x 0.39 Inches (19.6 x 6.0 x 10.0 mm)
Non-Conductive Black Plastic (UL94-V0)
0.07 Oz (2.1g)
Case Material
Weight
Reliability Specifications
Parameter
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Conditions
Min.
Typ.
Typ.
Max.
Units
MTBF
MIL HDBK 217F, 25ºC, Gnd Benign
3.5
MHours
Absolute Maximum Ratings
Parameter
Conditions
Min.
Max.
9.0
Units
5 VDC Input -0.7
12 VDC Input -0.7
24 VDC Input -0.7
Input Voltage Surge (1 Sec)
18.0
30.0
300
450
VDC
Lead Temperature
1.5 mm From Case For 10 Sec
All Models
ºC
Internal Power Dissipation
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Input
Output 1
Output 2
Fuse Rating
Slow-Blow
(mA)
Model
Efficiency
(%, Typ)
Voltage (VDC)
Number
Current (mA)
Voltage Current
Current Voltage Current
Current
(VDC)
(mA, Max) (mA, Min)
(VDC)
(mA, Max) (mA, Min)
Nominal
5
Range
Full-Load No-Load
D101ED
D102ED
D103ED
D104ED
D111ED
D112ED
D113ED
D114ED
D121ED
D122ED
D123ED
D124ED
4.5 - 5.5
285
263
259
256
115
107
107
104
58
30
30
30
30
12
12
12
12
7
5.0
9.0
100.0
56.0
42.0
33.0
100.0
56.0
42.0
33.0
100.0
56.0
42.0
33.0
10.0
6.0
4.2
3.3
10.0
6.0
4.2
3.3
10.0
6.0
4.2
3.3
5.0
9.0
100.0
56.0
42.0
33.0
100.0
56.0
42.0
33.0
100.0
56.0
42.0
33.0
10.0
6.0
4.2
3.3
10.0
6.0
4.2
3.3
10.0
6.0
4.2
3.3
70
76
77
78
72
78
78
80
71
77
76
76
500
500
500
500
250
250
250
250
125
125
125
125
5
4.5 - 5.5
5
4.5 - 5.5
12.0
15.0
5.0
12.0
15.0
5.0
5
4.5 - 5.5
12
12
12
12
24
24
24
24
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
9.0
9.0
12.0
15.0
5.0
12.0
15.0
5.0
54
7
9.0
9.0
55
7
12.0
15.0
12.0
15.0
55
7
Notes:
Block Diagram
1. Output load regulation is specified for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external ceramic
capacitor (approx approx 1 µF to 10 µF) be placed from each output to
common.
3. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
4. These converters are specified for operation without external components.
However, in some applications the addition of input/ouput capacitors will
enhance stability and reduce output ripple. Recommended capacitor values
are:
Input
Capacitor
Output
Capacitor
Vin
Vout
5 VDC
12 VDC
24 VDC
4.7 µF
2.2 µF
1.0 µF
5 VDC
9 VDC
12 VDC
15 VDC
4.7 µF
2.2 µF
1.0 µF
0.47 µF
For applications requiring very low output noise levels, a simple LC filter
should be effective.
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin
Function
1
2
4
5
6
7
+Vin
-Vin
-Vout 1
+Vout 1
-Vout 2
+Vout 2
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = 0.01 ( 0.25)
• Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
•
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
相关型号:
D102J11B202DQF
Rocker Switch, SPST, Latched, Solder Terminal, Rocker Actuator, Through Hole-straight, ROHS COMPLIANT
ITT
D102J11B202HQA
Rocker Switch, SPST, Latched, Solder Terminal, Rocker Actuator, Through Hole-straight, ROHS COMPLIANT
ITT
D102J11B202HQF
Rocker Switch, SPST, Latched, Solder Terminal, Rocker Actuator, Through Hole-straight, ROHS COMPLIANT
ITT
D102J11B202NQF
Rocker Switch, SPST, Latched, Solder Terminal, Rocker Actuator, Through Hole-straight, ROHS COMPLIANT
ITT
D102J11B202PQA
Rocker Switch, SPST, Latched, Solder Terminal, Rocker Actuator, Through Hole-straight, ROHS COMPLIANT
ITT
D102J11B202QA
Rocker Switch, SPST, Latched, Solder Terminal, Rocker Actuator, Through Hole-straight, ROHS COMPLIANT
ITT
©2020 ICPDF网 联系我们和版权申明