D116EI [MPD]
Low Cost, 1W SIP High Isolation DC/DC Converters; 低成本, SIP 1W高隔离的DC / DC转换器型号: | D116EI |
厂家: | MICROPOWER DIRECT, LLC |
描述: | Low Cost, 1W SIP High Isolation DC/DC Converters |
文件: | 总2页 (文件大小:177K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
D100EI Series
Low Cost, 1W SIP
High Isolation
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min.
Typ.
5.0
Max.
5.5
Units
Key Features:
5 VDC Input
4.5
• 1W Output Power
• Miniature SIP Case
• 3,000 VDC Isolation
• UL Approved (File E245422)
• Single & Dual Outputs
• >3.5 MHour MTBF
• 24 Standard Models
• LOWEST COST!!
Input Voltage Range
12 VDC Input 10.8
24 VDC Input 21.6
Internal Capacitor
12.0
24.0
13.2
26.4
VDC
Input Filter
Reverse Polarity Input Current
0.3
A
Output
Parameter
Conditions
Min.
Typ.
1.0
0.1
1.2
Max.
3.0
Units
%
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Dual Output , Balanced Loads
For Vin Change of 1%
1.0
%
%
Load Regulation (Note 1)
Ripple & Noise (20 MHz) (Note 2)
Output Power Protection
Temperature Coefficient
Output Short Circuit
General
See Model Selection Guide
50
75
mV P - P
%
120
0.02
0.03
%/ºC
Momentary (1.0 Sec.)
RoHS Compliant
Parameter
Conditions
Conditions
Min.
60 Seconds 3,000
500 VDC 1,000
100 kHz, 1V
Typ.
Max.
Units
VDC
MΩ
pF
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Parameter
60
150
kHz
Min.
Typ.
Max.
+85
Units
ºC
Operating Temperature Range
Storage Temperature Range
Cooling
Ambient
-40
-55
+25
+125
ºC
Free Air Convection
RH, Non-condensing
Humidity
95
%
Physical
Case Size
0.77 x 0.24 x 0.40 Inches (19.6 x 6.0 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.07 Oz (2.1g)
MicroPower Direct
292 Page Street
Suite D
Case Material
Weight
Stoughton, MA 02072
USA
Reliability Specifications
Parameter
Conditions
Min.
Typ.
Max.
Units
MTBF
MIL HDBK 217F, 25ºC, Gnd Benign
3.5
MHours
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Safety Standards
Safety Approvals
Absolute Maximum Ratings
Parameter
UL 1950, EN 60950, IEC 60950
UL, cUL; File No. E245422
Conditions
Min.
Typ.
Max.
9.0
Units
5 VDC Input -0.7
Input Voltage Surge (1 Sec)
12 VDC Input -0.7
24 VDC Input -0.7
18.0
30.0
300
450
VDC
Lead Temperature
1.5 mm From Case For 10 Sec
All Models
ºC
Internal Power Dissipation
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Input
Output
Voltage Current
(VDC) (mA, Max) (mA, Min)
Load
Regulation
(%, Max)
Fuse Rating
Slow-Blow
(mA)
Model
Efficiency
(%, Typ)
Voltage (VDC)
Number
Current (mA)
Full-Load No-Load
Current
Nominal
5
Range
D101EI
D102EI
D103EI
D104EI
D105EI
D106EI
D107EI
D108EI
D111EI
D112EI
D113EI
D114EI
D115EI
D116EI
D117EI
D118EI
D121EI
D122EI
D123EI
D124EI
D125EI
D126EI
D127EI
D128EI
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
286
267
256
250
278
267
256
253
115
110
105
103
113
110
105
104
57
54
52
51
56
55
52
51
30
30
30
30
30
30
30
30
15
15
15
15
15
15
15
15
8
8
8
8
8
8
8
8
5.0
9.0
12.0
15.0
5.0
200.0
111.0
83.0
67.0
100.0
56.0
42.0
33.0
200.0
111.0
83.0
67.0
100.0
56.0
42.0
33.0
200.0
111.0
83.0
67.0
100.0
56.0
20.0
12.0
9.0
7.0
10.0
6.0
5.0
4.0
20.0
12.0
9.0
7.0
10.0
6.0
5.0
4.0
20.0
12.0
9.0
7.0
10.0
6.0
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
70
75
78
80
72
75
78
79
72
76
79
81
74
76
79
80
73
77
80
82
74
76
80
81
500
500
500
500
500
500
500
500
200
200
200
200
200
200
200
200
100
100
100
100
100
100
100
100
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
9.0
12.0
15.0
5.0
9.0
12.0
15.0
5.0
9.0
12.0
15.0
5.0
9.0
12.0
15.0
5.0
9.0
12.0
15.0
42.0
33.0
5.0
4.0
Derating Curve
Other input/output combinations are available
(i.e. 3.3 VDC). Contact the factory for details at:
sales@micropowerdirect.com
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
3. These converters will operate without external components. However,
when measuring output ripple, it is recommended that an external ceramic
capacitor be placed
Output Capacitor
Single Dual
5 VDC 10.0 μF 4.7 μF
Input
Capacitor
from the +Vout pin to
the -Vout pin for single
output units and from
each output to common
for dual output units.
An input capacitor will
enhance stability over
Vin
Vout
5 VDC
12 VDC
24 VDC
4.7 μF
2.2 μF
1.0 μF
9 VDC
4.7 μF
2.2 μF
1.0 μF
12 VDC 2.2 μF
15 VDC 1.0 μF 0.47 μF
Mechanical Dimensions
temperature and input line variations. Recommended capacitor values are
given in the table above. For applications requiring very low output noise
levels, a simple LC filter should be effective.
4. Dual output units may be connected to provide a 10V, 18V, 24V or
30 VDC output. To do this, connect the load across the positive (+Vout) and
negative (-Vout) outputs and float the output common
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Pin Connections
Pin Single
Dual
Pin
Single
Dual
1
2
5
+Vin
-Vin
+Vin
-Vin
6
7
No Pin
+Vout
Common
+Vout
-Vout
-Vout
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = 0.01 ( 0.25)
• Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
•
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
相关型号:
©2020 ICPDF网 联系我们和版权申明