Model Selection Guide
www.micropowerdirect.com
Input
Output
Overvoltage Capacitive Fuse Rating
Model
Number
Efficiency
(%, Typ)
Voltage (VDC)
Current (mA)
Protection
(VDC)
Load
(µF Max.)
Slow-Blow
Voltage
(VDC)
Current
Current
(mA, Min)
(mA)
(mA, Max)
Nominal
Range
Full-Load No-Load
F2001ERW
F2002ERW
F2003ERW
F2004ERW
F2005ERW
F2006ERW
F2007ERW
F2008ERW
F2009ERW
F2011ERW
F2012ERW
F2013ERW
F2014ERW
F2015ERW
F2016ERW
F2017ERW
F2018ERW
F2019ERW
F2021ERW
F2022ERW
F2023ERW
F2024ERW
F2025ERW
F2026ERW
F2027ERW
F2028ERW
F2029ERW
12
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
24
48
48
48
48
48
48
48
48
48
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
36.0 - 75.0
1,937
2,109
2,057
2,032
2,008
2,083
2,032
2,032
2,008
968
1,028
1,004
980
968
1,028
968
968
968
479
502
496
496
484
514
40
40
40
40
40
40
40
40
40
20
20
20
20
20
20
20
20
20
10
10
10
10
10
10
10
10
10
3.3
5.0
12.0
15.0
24.0
5.0
12.0
15.0
24.0
3.3
5,400
4,000
1,670
1,330
830
2,000
833
666
540
400
167
133
83
200
84
67
86
79
81
82
83
80
82
82
83
86
81
83
85
86
81
86
86
86
87
83
84
84
86
81
86
86
86
4.29
6.5
15.6
19.5
31.2
6.5
15.6
19.5
31.2
4.29
6.5
15.6
19.5
31.2
6.5
15.6
19.5
31.2
4.29
6.5
15.6
19.5
31.2
6.5
13,000
6,800
2,200
755
500
3,400
680
450
220
13,000
6,800
2,200
755
500
3,400
680
450
220
13,000
6,800
2,200
755
500
3,400
680
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
2,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
416
42
5,400
4,000
1,670
1,330
830
2,000
833
666
540
400
167
133
83
200
84
67
5.0
12.0
15.0
24.0
5.0
12.0
15.0
24.0
3.3
416
42
5,400
4,000
1,670
1,330
830
2,000
833
666
540
400
167
133
83
200
84
67
5.0
12.0
15.0
24.0
5.0
12.0
15.0
24.0
484
484
484
15.6
19.5
31.2
450
220
416
42
Notes:
Remote ON/OFF
Pin Connections
0. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 0 µF to
0± µF) be placed from the +Vout to the -Vout pins or single output units and from each output to common for
dual output units.
Parameter
Supply On
Supply Off
Min
Max
Units
Pin Single Dual
0.5 40.0 or Open VDC
Grnd <0.5 VDC
Control Common Referenced to Gnd
Remote ON/OFF Notes:
0. Maximum sink current at the on/off pin (pin 6) during a logic
low is 0±± µA.
1
2
4
5
6
7
8
+Vin
-Vin
Remote On/Off
No Pin +Vout
+Vout Comm.
+Vin
-Vin
2. These converters are specified for operation
Input
Capacitor
Output
Capacitor
Vin
without external components. However, in some
applications the addition of input/ouput capacitors
will enhance stability and reduce output ripple.
Recommended capacitor values are given in the
table at right. For applications requiring very low
output noise levels, a simple LC filter should be
effective.
02 VDC
24 VDC
48 VDC
0±± µF
0±± µF
0±± µF
0,±±± µF per 0A of Iout
0,±±± µF per 0A of Iout
0,±±± µF per 0A of Iout
-Vout
Trim
-Vout
Trim
2. Maximum allowable leakage current of a switch connected to
the on/off terminal (Pin 6) at logic high (2.5V to 0±±V) is 5 µA.
3. Overload protection is provided by a power limiting circuit. Long term operation under overload conditions
may cause damage to the unit.
4. Transient recovery is measured to within a 0% error band for a load step change of 75% to 0±±%.
5. These units should not be operated with a load under 0±% of full load. Operation at no-load will not damage
the unit, but they may not meet all specifications.
Mechanical Dimensions
6. A simple external circuit may be used to adjust the converter output. To adjust the output DOWN, connect a
5%, 3W resistor between the plus output pin and the Vout trim pin. To adjust the output UP, connect a 5%, 3W
resistor between the minus output pin and the Vout trim pin. For UP/Down trimming capability, connect a
0± kW potentiometer between the plus and minus outputs with the wiper arm connected to the Vout trim pin.
7. These units should not be operated over +70°C (see derating curve). Exceeding +70°C may damage the unit.
8. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection
table above for the correct rating.
Derating Curve
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±±.±0 (±±.25)
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com