H125E [MPD]
Low Cost, 1W, Ultra-Miniature DC/DC Converters; 低成本, 1W ,超小型DC / DC转换器型号: | H125E |
厂家: | MICROPOWER DIRECT, LLC |
描述: | Low Cost, 1W, Ultra-Miniature DC/DC Converters |
文件: | 总2页 (文件大小:204K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
H100E Series
Low Cost, 1W,
Ultra-Miniature
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 1W Output Power
Input
Parameter
Conditions
3.3 VDC Input
5 VDC Input
Min.
3.0
Typ.
3.3
Max.
3.6
Units
• Miniature MiniDIP Case
• UL Approved (File E245422)
• 1,000 VDC Isolation
• >3.5 MHour MTBF
4.5
5.0
5.5
Input Voltage Range
VDC
12 VDC Input 10.8
24 VDC Input 21.6
Internal Capacitor
12.0
24.0
13.2
26.4
Input Filter
Reverse Polarity Input Current
0.3
A
• 17 Standard Models
• Industry Standard Pin-Out
• LOWEST COST!
Output
Parameter
Output Voltage Accuracy
Line Regulation, 3.3V Output Models
Line Regulation, All Other Models
Load Regulation
Conditions
Min.
Typ.
Max.
3.0
Units
1.0
%
1.5
For Vin Change of 1%
%
1.2
See Model Selection Guide
Ripple & Noise (20 MHz)
Output Power Protection
Temperature Coefficient
Output Short Circuit
General
75
100
mV P - P
%
120
0.03
%/ºC
Momentary (1.0 Sec.)
Parameter
Conditions
Conditions
Min.
60 Seconds 1,000
500 VDC 1,000
100 kHz, 1V
Typ.
Max.
Units
VDC
MΩ
pF
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
60
100
100
kHz
Parameter
Min.
Typ.
Max.
+85
Units
ºC
Operating Temperature Range
Storage Temperature Range
Cooling
Ambient
-40
-55
+25
+125
ºC
Free Air Convection
RH, Non-condensing
Humidity
95
%
Physical
Case Size, Single Output Models
0.50 x 0.393 x 0.30 Inches (12.70 x 10.00 x 7.70 mm)
Non-Conductive Black Plastic (UL94-V0)
0.06 Oz (1.8g)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Case Material
Weight
Reliability Specifications
Parameter
Conditions
Min.
Typ.
Max.
Units
MTBF
MIL HDBK 217F, 25ºC, Gnd Benign
3.5
MHours
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Safety Standards
UL 1950, EN 60950, IEC 60950
UL, cUL; File No. E245422
Safety Approvals
Not 3.3 Vout Models
Absolute Maximum Ratings
Parameter
Conditions
Min.
Typ.
Max.
7.0
Units
3.3 VDC Input -0.7
5 VDC Input -0.7
12 VDC Input -0.7
24 VDC Input -0.7
9.0
Input Voltage Surge (1 Sec)
VDC
18.0
30.0
300
450
Lead Temperature
1.5 mm From Case For 10 Sec
All Models
ºC
Internal Power Dissipation
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Input
Output
Current
(mA, Max)
303.0
200.0
111.0
83.0
Load
Regulation
(%, Max)
Fuse Rating
Slow-Blow
(mA)
500
Model
Number
Efficiency
(%, Typ)
Voltage (VDC)
Nominal Range
Current (mA)
Voltage
(VDC)
3.3
Current
(mA, Min)
30.0
20.0
12.0
9.5
Full-Load
No-Load
H101E
H102E
H103E
H104E
H105E
H111E
H112E
H113E
H114E
H115E
H121E
H122E
H123E
H124E
H125E
H151E
H152E
5
5
5
5
5
12
12
12
12
12
24
24
24
24
24
3.3
3.3
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
3.0 - 3.6
278
286
256
252
251
116
118
109
106
105
56
25
25
25
25
25
16
16
16
16
16
8
20
15
10
10
10
20
15
10
10
10
20
15
10
10
10
20
72
70
78
79
80
72
71
76
78
80
74
73
78
79
80
72
74
5.0
9.0
12.0
15.0
3.3
5.0
9.0
12.0
15.0
3.3
5.0
9.0
12.0
15.0
3.3
500
500
500
500
200
200
200
200
200
100
100
100
100
100
750
750
67.0
7.0
303.0
200.0
111.0
83.0
30.0
20.0
12.0
9.0
67.0
7.0
303.0
200.0
111.0
83.0
67.0
303.0
200.0
30.0
20.0
12.0
9.0
7.0
30.0
20.0
57
8
53
8
53
8
53
8
421
410
55
55
3.0 - 3.6
5.0
20
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external 0.33 µF
ceramic capacitor be placed from the +Vout pin to the -Vout pin.
3. During operation, care must be taken not to exceed the specified input range
of the unit or to allow the output load to drop below the specified minimum
(10% of full load). Operating the unit under either of these conditions could
cause damage to the unit.
Derating Curve
4. These converters are specified for operation without external components.
However, in some applications the addition of input/output capacitors will
enhance stability and reduce output ripple. Recommended capacitor values
are:
Input
Capacitor
4.7 µF
4.7 µF
2.2 µF
Output
Capacitor
10.0 µF
10.0 µF
4.7 µF
2.2 µF
1.0 µF
Vin
Vout
3.3 VDC
5 VDC
12 VDC
24 VDC
3.3 VDC
5 VDC
9 VDC
12 VDC
15 VDC
1.0 µF
For applications requiring very low output noise levels, a
simple LC filter should be effective.
5. It is recommended that a fuse be used on the input of a power
supply for protection. See the table above for the correct rating.
Mechanical Dimensions
Pin Connections
Pin
Function
1
4
5
7
-Vin
+Vin
+Vout
-Vout
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = 0.01 ( 0.25)
• Pin 1 is marked by a “dot” or indentation on the
top of the unit
MicroPower Direct
•
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
相关型号:
©2020 ICPDF网 联系我们和版权申明