ML105S09E [MPD]
ML100SE SERIES;
| 型号： | ML105S09E |
| 厂家： | 
MICROPOWER DIRECT, LLC |
| 描述： | ML100SE SERIES |
| 文件： | 总2页 (文件大小：291K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Series
ML100SE
Low Cost, Single Output
Ultra-Miniature SMT
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Key Features:
• 1W Output Power
• Ultra-Miniature SMT Case
• 1,500 VDC Isolation
• Short Circuit Protected
• Single Output
Conditions
Min.
4.5
Typ.
5.0
Max.
5.5
Units
5 VDC Input
12 VDC Input 10.8
15 VDC Input 13.5
24 VDC Input 21.6
Capacitor
12.0
15.0
24.0
13.2
16.5
26.4
Input Voltage Range
VDC
Input Filter
• -40°C to +105°C Operation
• >3.5 MHour MTBF
• 17 Standard Models
• LOW COST!
Output
Parameter
Conditions
Min.
Typ.
3.0
Max.
Units
%
Output Voltage Accuracy
Capacitive Load
Line Regulation
Load Regulation, See Note 1
220
1.2
µF
For Vin Change of 1%
%
See Model Selection Guide
Output Voltage <12 VDC
15 VDC, 24 VDC Output
30
60
Ripple & Noise (20 MHz), See Note 2
mV P - P
%/ºC
Temperature Coefficient
Output Short Circuit
General
0.03
Continuous (Autorecovery)
Parameter
Conditions
Min.
60 Seconds 1,500
500 VDC 1,000
100 kHz, 1V
Typ.
Max.
Units
VDC
M⍀
pF
Isolation Voltage
Isolation Resistance
Isolation Capacitance, See Note 3
Switching Frequency
EMI Characteristics
Parameter
20
100
300
kHz
Conditions
Min.
Typ.
Max.
Units
EMI Compliance, See Note 5
EMC Compliance
Environmental
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Conducted
CISPR22/EN 55022 Level B
Electrostatic Discharge (ESD) EN 61000-4-2 Level B Contact 8 kV
Conditions
Min.
-40
Typ.
+25
Max.
+105
+125
Units
ºC
Ambient
-55
ºC
Free Air Convection
RH, Non-condensing
Humidity
95
%
Physical
Case Size
0.50 x 0.327 x 0.285 Inches (12.70 x 8.30 x 7.25 mm)
Non-Conductive Black Plastic (UL94-V0)
0.05 Oz (1.52g)
Case Material
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Weight
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Min.
3.5
Typ.
Typ.
Max.
Units
MHours
Absolute Maximum Ratings
Parameter
T: (781) 344-8226
F: (781) 344-8481
Conditions
Min.
Max.
9.0
Units
VDC
ºC
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
5 VDC Input -0.7
12 VDC Input -0.7
15 VDC Input -0.7
24 VDC Input -0.7
18.0
21.0
30.0
300.0
Input Voltage Surge (1 Sec)
Lead Temperature
1.5 mm From Case For 10 Sec
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
Model Selection Guide
www.micropowerdirect.com
Input
Output
Fuse Rating
Load Regulation
Model
Efficiency
(%, Typ)
Voltage (VDC)
Nominal Range
Current (mA)
Full-Load No-Load
Slow-Blow
(mA)
Voltage Current
Current
Number
(VDC) (mA, Max) (mA, Min)
% Typ. % Max
ML105S-05E
ML105S-09E
ML105S-12E
ML105S-15E
ML105S-24E
ML112S-05E
ML112S-09E
ML112S-12E
ML112S-15E
ML112S-24E
ML115S-05E
ML115S-15E
ML124S-05E
ML124S-09E
ML124S-12E
ML124S-15E
ML124S-24E
5
5
5
5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
13.5 - 16.5
13.5 - 16.5
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
250
250
250
250
250
104
104
103
103
103
83
82
52
52
51
51
51
20
20
20
20
20
15
15
15
15
15
10
10
7
5.0
9.0
12.0
15.0
24.0
5.0
200.0
111.0
84.0
67.0
42.0
200.0
111.0
84.0
67.0
42.0
200.0
67.0
200.0
111.0
84.0
20.0
12.0
8.0
7.0
4.0
20.0
12.0
8.0
7.0
4.0
20.0
7.0
20.0
12.0
8.0
12.0
8.0
7.0
6.0
5.0
12.0
8.0
7.0
6.0
5.0
12.0
6.0
12.0
8.0
7.0
6.0
5.0
15.0
10.0
10.0
10.0
10.0
15.0
10.0
10.0
10.0
10.0
15.0
10.0
15.0
10.0
10.0
10.0
10.0
80
80
80
80
80
80
80
81
81
81
80
81
80
80
81
81
81
500
500
500
500
500
200
200
200
200
200
200
200
100
100
100
100
100
5
12
12
12
12
12
15
15
24
24
24
24
24
9.0
12.0
15.0
24.0
5.0
15.0
5.0
7
7
7
7
9.0
12.0
15.0
24.0
67.0
42.0
7.0
4.0
Notes:
Derating Curve
1. Output load regulation is specified for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from
the +Vout pin to the -Vout pin.
3. The isolation capacitance of model ML124S-24E is 30 pF.
4. Operation at no load will not damage these units, however, they may not meet all specifications.
5. These converters are specified for operation without external components. However, in some applications the
addition of input/output capacitors will enhance stability and reduce output ripple.The simple connection shown
below will typically meet EN 55022 Class B.
VIN
C1
L1
C2
---
VOUT
5 VDC
C3
5 VDC
4.7 µF/50V
4.7 µF/50V
4.7 µF/50V
4.7 µF/50V
6.8 µH
6.8 µH
6.8 µH
6.8 µH
10 µF
4.7 µF
2.2 µF
1.0 µF
0.47 µF
Pin Connections
12 VDC
15 VDC
24 VDC
---
9 VDC
Pin Description
Pin Description
470 pF/2kV
470 pF/2kV
12 VDC
15 VDC
24 VDC
1
2
-VIN
4
5
8
-VOUT
+VOUT
NC
+VIN
NC = No Connection
6. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Mechanical Dimensions
Board Layout
Notes:
•
•
•
All dimensions are typical in inches (mm)
Tolerance x.xx = 0.01 ( 0.25)
Pin 1 is marked by a “dot” or indentation on the unit
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
相关型号：
©2020 ICPDF网 联系我们和版权申明