MPM20S15EPB [MPD]
MPM-20EPB Series;
| 型号： | MPM20S15EPB |
| 厂家： | 
MICROPOWER DIRECT, LLC |
| 描述： | MPM-20EPB Series |
| 文件： | 总2页 (文件大小：364K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Series
MPM-20EPB
Very Low Cost, 20W
Compact “Power Brick”
AC/DC Power Supplies
Key Features:
Electrical Specifications
Specifications typical @ +25°C, 230 VAC input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
• 20W Output Power
Input
Parameter
• Compact 1.1 x 2.1 Inch Case
• Universal 85-264 VAC Input
• EN 60950 Approved (UL)
• Meets IEC Safety Class II
• Industry Standard Pin-Out
• Meets EN 55022 Class B
• >300 kHour MTBF
Conditions
Min.
85
110
47
Typ.
Max.
264
370
440
Units
VAC
VDC
Hz
Input Voltage Range
Input Frequency
Input Current
See Model Selection Guide
115 VAC
230 VAC
20.0
40.0
Inrush Current
A Pk
Output
Parameter
Conditions
Min.
Typ.
Max.
Units
• Low, Low Cost
Output Voltage
Output Current
Output Voltage Accuracy
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
See Model Selection Guide
See Model Selection Guide
See Note 1
VIN = Min to Max
See Note 3
2.0
%
%
%
0.5
1.0
50
120
mV P-P
115 VAC
230 VAC
10
50
0.02
Hold-Up Time
mSec
%/°C
Temperature Coefficient
Short Circuit Protection
Over Voltage Protection
Overload Protection
General
Continuous (Autorecovery)
Zener Diode Clamp
Autorecovery 110
%W
Parameter
Conditions
Min.
Typ.
Max.
Units
VAC
M
Isolation Voltage
Isolation Resistance
Switching Frequency
EMI Characteristics
Parameter
Radiated Emissions
Conducted Emissions
ESD
Input to Output 3,000
500 VDC
100
100
kHz
Standard
Min.
Typ.
Max.
Class B
Class B
Units
EN 55022
EN 55022
EN 61000-4-2 Criteria B; 8 kV Air/ 6 kV Contact
RS
EFT
Surge
CS
PFMF
Voltage Dips
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
Criteria A; 10V/m
Criteria B; 4 kV
Criteria B; 2 kV
Criteria A; 10 Vrms
Criteria A; 10A/m
Criteria B; 0% - 70%
See Note 5
Environmental
Parameter
Conditions
Min.
-40
Typ.
+25
Max.
+70
+95
Units
°C
°C
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Ambient
Case
-40
+105
°C
Free Air Convection (See Derating Curve)
RH, Non-condensing 95
Humidity
%
Physical
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Case Size
2.12 x 1.13 x 0.925 Inches (53.8 x 28.8 x 23.50 mm)
Non-Conductive Black Plastic (UL94-V0)
1.76 Oz (50g)
Case Material
Weight
Reliability Specifications
Parameter
Conditions
Min.
Typ.
Max.
Units
MTBF
MIL HDBK 217F, 25°C, Gnd Benign
300
kHours
Safety Standards
Safety Class
EN 60950
IEC 60536 Class II
www.micropowerdirect.com
Model Selection Guide
www.micropowerdirect.com
Notes:
Input
Output
1. For the 3.3V output model, Output Accuracy is 3.0%
2. Operation at no load will not damage the units, however, they may not
meet all specifications.
Standby Capacitive
Model
Number
Efficiency
(%, Typ)
Current (A)
Power
Load
Voltage Current
(W, Max)
(µF Max.)
(VDC)
(A Max.)
115 VAC 230 VAC
3. Load regulation is measured for an output change of 10% to 100% at
nominal input line.
4. All units are rated for EN 55022 (CE/RE) class B without external components.
5. All units are rated for EN 61000-4-4 ( 4 kV) and EN 61000-4-5 ( 2 kV) without
external components. They will meet EN 61000-4-5 ( 4 kV/ 6 kV) with ad-
ditional input filtering as shown below.
6. It is recommended that a fuse be used on the input of a power supply for
protection. For the MPM-20S-xxEPB series, a 3.15A/250 VAC slow
blow should be used.
MPM-20S-03EPB 0.370
MPM-20S-05EPB 0.370
MPM-20S-12EPB 0.370
MPM-20S-15EPB 0.370
MPM-20S-24EPB 0.370
0.240
0.240
0.240
0.240
0.240
3.3
5.0
12.0
15.0
24.0
3.600
3.600
1.660
1.330
0.833
0.3
0.3
0.3
0.3
0.3
10,000
10,000
5,400
2,700
1,500
74
78
82
83
83
The diagram below illustrates a typical application connection of the MPM-20EPB series. Notes on this circuit (starting with the input circuit) are:
1. It is recommended that an external fuse and NTC be used.The recommended
Typical Connection
fuse is a 3.15A/250V slow blow and for the NTC, a 5D-9.
2. An external MOV is required on the input to protect the unit in the event of a
surge. A 561KD20 or equivalent is recommended.
3. Recommended output filtering capacitors are:
C1
C2
TVS
MPM-20S-03EPB 1.0 µF/50V
MPM-20S-05EPB 1.0 µF/50V
MPM-20S-12EPB 1.0 µF/50V
MPM-20S-15EPB 1.0 µF/50V
MPM-20S-24EPB 1.0 µF/50V
220 µF/10V
220 µF/10V
120 µF/25V
120 µF/25V
68 µF/35V
SMBJ7.0A
SMBJ7.0A
SMBJ20A
SMBJ20A
SMBJ30A
The output filtering capacitor (C2) is a high frequency,low resistance electrolytic
capacitor. Capacitor (C1) is ceramic. Voltage derating of capacitors should be
80% or above.
Typical Connection: With ACFM-02 Input Module (See note 4)
4. Input noise and surge suppression modules are available for a number of MPD
AC/DC power supplies. An MPM-20S-xxEPB connection with the ACFM-02
is illustrated in the diagram at left. For pricing or full technical information on
these modules (ACFM-01 and ACFM-02) please contact the factory.
Pin Connections
Pin Function
Pin Function
1
2
AC-Neutral
AC-Line
3
4
+Vo
-Vo
Derating Curve
Mechanical Dimensions
Input Voltage Vs Load
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = 0.02 ( 0.50)
The MPM-20-xxEPB series is also available
with a chassis mount or DIN mount adapter.
Contact the factory for more information
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
相关型号：
©2020 ICPDF网 联系我们和版权申明