MP2617GL [MPS]
3A Switching Charger with NVDC Power Path Management For Single Cell Li Battery;![MP2617GL](http://pdffile.icpdf.com/pdf2/p00341/img/icpdf/MP2617_2097175_icpdf.jpg)
型号: | MP2617GL |
厂家: | ![]() |
描述: | 3A Switching Charger with NVDC Power Path Management For Single Cell Li Battery 电池 |
文件: | 总29页 (文件大小:1036K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
MP2617
3A Switching Charger with NVDC
Power Path Management
For Single Cell Li+ Battery
The Future of Analog IC Technology
DESCRIPTION
FEATURES
The MP2617 is a monolithic switch mode
battery charger with power path management
for single-cell Li-ion batteries in a wide range of
tablet and other portable devices. It integrates a
synchronous BUCK regulator to provide
regulated voltage for powering the system
output and at the same time charging the
battery. This device supports both USB and
high power DC adapter input. In USB mode, the
input current limit can be programmed to
450mA or 825mA via the logic pins to cover the
USB2.0 and USB3.0 specifications. When the
adapter input is present, the input current can
also be limited in order to avoid overloading of
the DC adapter. Input current limit can be
programmed up to 3A.
•
•
•
4V to 14V Operating Input Voltage
Smart Power Path Management
Five Control Loops: Input Current Limit,
Input Voltage Limit, Constant Charge
Current, Terminal Battery Control and
Thermal Fold-Back.
1.6MHz Switching Frequency
Programmable Input Current Limit
Programmable Charge Current
•
•
•
•
•
Single Input for USB and AC adapter
Cover
Specification
Fully Integrated Power Switches
USB2.0
and
USB3.0
Input
•
•
No External Blocking Diode and Sense
Resistor Required
Charging Operation Indicator
Built-in Programmable Charging Timer
Thermal Limiting Regulation on Chip
Battery Temperature Monitor
•
•
•
•
•
The smart power path management allows
MP2617 to regulate the system voltage for
powering an external load and charging the
battery independently and simultaneously. This
allows immediate system operation even under
missing or deeply discharged battery. When the
input current limit is reached, the system load is
satisfied in priority, then the charger will take
the remaining current to charge the battery.
Additionally, the smart power path control
allows an internal connection from battery to the
system in order to supplement additional power
to the load in the event the system power
demand increases over the input limited power
or the input is removed.
Tiny Package Features Small Size.
APPLICATIONS
•
•
•
•
•
•
Smart Phone
E-Book
GPS
Portable Media Player
Portable Hand-held Solution
Tablet PC
All MPS parts are lead-free and adhere to the RoHS directive. For MPS green
status, please visit MPS website under Products, Quality Assurance page.
“MPS” and “The Future of Analog IC Technology” are registered trademarks of
Monolithic Power Systems, Inc.
The MP2617 features high integration with all
the power switches included inside. No external
MOSFET, blocking diodes, or current sense
resistor is required.
Two status monitor output pins are provided to
indicate the battery charge status and power
source status. Other features include trickle
charge, battery temperature monitoring, timer
and thermal limiting regulation on chip.
MP2617 is available in QFN 3mmx4mm
package.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
1
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
TYPICAL APPLICATION
ON
OFF
AC adapter
/USB input
VILIM
M0
M1
EN
L
SYS Load
SW
IN
100
90
80
70
60
R4
R5
C6
C2
CHGOK
BST
SYS
ACOK
VCC
R1
SYSFB
PGND
MP2617
RT1
C1
C5
NTC
R2
ICHG
BATT
v
BATT
TMR
R
T2
CTMR
RNTC
ISET
ILIM
C3
R
ISET
AGND
50
40
R
ILIM
0
1
2
3
0
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
2
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
ORDERING INFORMATION
Part Number*
Package
Top Marking
MP2617GL
QFN 3mmx4mm
MP2617
* For Tape & Reel, add suffix –Z (e.g. MP2617GL–Z);
PACKAGE REFERENCE
TOP VIEW
VCC VLIM
TMR ILIM
18
20
19
17
16 NTC
1
2
3
4
5
6
BST
15
ISET
SW
IN
14
13
BATT
SYS
SW
P GND
EN
12 SYSFB
AGND
11
7
8
9
10
M0
M1
CHGOK ACOK
ABSOLUTE MAXIMUM RATINGS (1)
IN, SW .........................................-0.3V to +20V
BATT, SYS .....................................-0.3V to +6V
BST...............................................-0.3V to +26V
All Other Pins..................................-0.3V to +6V
Thermal Resistance (4)
QFN20 3mmx4mm .................48...... 11... °C/W
θJA
θJC
Notes:
1) Exceeding these ratings may damage the device.
2) The maximum allowable power dissipation is a function of the
maximum junction temperature TJ (MAX), the junction-to-
ambient thermal resistance θJA, and the ambient temperature
TA. The maximum allowable continuous power dissipation at
any ambient temperature is calculated by PD (MAX) = (TJ
(MAX)-TA)/θJA. Exceeding the maximum allowable power
dissipation will cause excessive die temperature, and the
regulator will go into thermal shutdown. Internal thermal
shutdown circuitry protects the device from permanent
damage.
(2)
Continuous Power Dissipation (TA = +25°C)
QFN20 3mmx4mm..................................... 2.6W
Junction Temperature...............................150°C
Lead Temperature ....................................260°C
Storage Temperature.................–65°C to 150°C
Recommended Operating Conditions (3)
Supply Voltage VIN ...........................4.5V to 12V
Operating Junction Temp. (TJ).... -40°C to +125°C
3) The device is not guaranteed to function outside of its
operating conditions.
4) Measured on JESD51-7, 4-layer PCB.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
3
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
ELECTRICAL CHARACTERISTICS
VIN = 5.0V, TA = 25°C, unless otherwise noted.
Parameters
Symbol Condition
Min
Typ
Max
Units
Input Power (IN)
IN Operating Range
VIN
4.0
3.65
3.35
270
70
14(5)
3.95
3.65
350
150
V
V
Rising
Falling
Rising
Falling
3.8
3.5
IN Under Voltage Lockout
Threshold
V
310
110
mV
mV
IN vs. BATT Threshold
Rising
2.75
2.6
2.9
2.75
1.6
3.05
2.9
V
V
BST Voltage Threshold
Switching Frequency
VBST-VSW
Falling
1.4
1.8
MHz
USB2.0 Mode
400
750
450
825
500
900
mA
mA
mA
USB3.0 Mode
Default Mode
Input Current Limit
IIN
1840
2000
2160
Programmable Mode,
RILIM=23k
1840
1.1
2000
1.14
2160
1.18
mA
V
Input Current Limit Reference
Voltage
VILIM
High-side NMOS On Resistance RH_DS(ON) Include the BLOCK FET
120
80
130
100
4.9
mΩ
mΩ
A
Low-side NMOS On Resistance
High-side NMOS Peak Current lim
Input Voltage Clamp Threshold
RL_DS(ON)
3.5
4.2
VVLIM
Voltage on VLIM
1.49
1.52
1.55
V
Charger Enabled, USB2.0
Mode
2.4
2.8
3.8
5
5
5
mA
mA
mA
Charger Enabled, USB3.0
Mode
Input Quiescent Current
IIN
Charger Enable,
Programmable Mode
Charger Enabled, Default
Mode
3.8
3
5
5
mA
uA
uA
Disabled, EN=0V
SYS to IN reverse current
blocking
SYS=SW=4.5V,VIN=0V,
monitor VIN leakage
0.01
0.2
SYS Output
Minimum
Voltage
SYS
Regulation
SYS voltage @ VBATT≤3.4V,
SYSFB float
VSYS
3.45
3.6
3.75
4.5
V
V
3.4V<VBATT≤4.2V, SYSFB floa
BATT Float
VBATT
0.2V
+
3.5
3.5
SYS Regulation Voltage
SYS Reference Voltage
VSYS
User Programmed by SYSFB
4.4
V
V
VSYS_REF
1.135
1.152
1.17
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
4
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
ELECTRICAL CHARACTERISTICS (continued)
VIN = 5.0V, TA = 25°C, unless otherwise noted.
Parameters
Symbol Condition
Min
Typ
Max
0.05
4
Units
VIN=0V, ISYS=200mA,
VBATT=4.2V
BATT to SYS Resistance
0.04
Ω
VSYS>VBATT–800mV
2.6
3.3
A
BATT to SYS Current Limit
SYS short
200
mA
Battery Charger
VBATT>VRECH, ICHG≤IBF,
SYSFB float
4.168
4.2
4.232
V
V
Terminal Battery Voltage
VBATT
VSYS<4.2V Programmed
VSYS-
0.04 x IBF
by SYSFB Pin
SYSFB Float
3.9
4.0
4.1
V
V
Recharge Threshold at VBATT
VRECH
SYSFB programmed
3.85
3.95
85
4.05
Recharge Hysteresis
mV
V
Trickle Charge Threshold
Trickle Charger Hysteresis
Trickle Charge Current
Termination Charger Current
2.9
5%
3
3.1
200
mV
ICC
ICC
ITRICKLE
IBF
10%
10%
15%
200
IBF Maximum Limit
150
mA
RISET=760
RISET=1.53k
RISET=4.6k
2.475
1.26
0.405
1.1
2.75
1.4
3.025
1.54
0.495
1.2
A
A
A
V
V
V
Constant Current Mode Charge
Current
ICC
0.450
1.15
2.6
ISET Reference Voltage
Battery UVLO
Rising
Falling
2.4
2.8
2.2
2.4
2.6
VBATT
65mV
-
Idea Diode Regulation Voltage
BATT Leakage Current
VSYS
IBATT
Supplement Mode
mV
µA
VBATT=4.2V, SYS float,
20
30
VIN=PGND
__________ _____________
ACOK, CHGOK
__________ _____________
ACOK, CHGOK Pin Output Low
Voltage
__________ _____________
Sinking 5mA
270
0.1
350
0.5
mV
uA
Connected to 3.3V
ACOK,CHGOKPin Leakage Current
Timer
Trickle Charge Time
Total Charge Time
CTMR=0.1µF, ICHG=1A
CTMR=0.1µF, ICHG=1A
45
Min
6.5
Hour
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
5
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
ELECTRICAL CHARACTERISTICS (continued)
VIN = 5.0V, TA = 25°C, unless otherwise noted.
Parameters Symbol Condition
Negative Temperature Coefficient (NTC) Control
Min
Typ
Max
Units
R
0°C
NTC=NCP18XH103F
NTC Low Temp Rising Threshold
VTHL
63
65
35
67
%VCC
mV
Hysteresis on Low Temp
Threshold
NTC High Temp Falling
Threshold
R
50°C
NTC=NCP18XH103F,
VTHH
32
33.5
70
35
%VCC
mV
Hysteresis on High Temp
Threshold
VCC Supply
Rising
Falling
3.15
2.8
3.35
3
3.55
3.2
V
V
VCC UVLO
0mA<IVCC<25mA,
VIN=6V
VCC Output Voltage
4.3
4.5
40
4.6
V
VCC Short Circuit Current Limit
mA
Logic
0.4
8
V
V
EN Input Low Voltage
EN Input High Voltage
1.5
4
EN =4V
μA
EN Input Current
M0, M1
-0.5
1.5
-0.1
EN =0V
Logic High
Logic Low
V
V
0.4
Protection
Thermal Limit Temperature
Thermal Shutdown
Notes:
120
150
°C
°C
5) Using a inductor with the saturation current larger than 6A when applying the part with higher than 12V input.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
6
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
TYPICAL PERFORMANCE CHARACTERISTICS
VIN = 5.0V, VBATT = Full Range, Default Mode, IIN Limit=2A, VSYS=4.4V, R6 and R7 are float, ICHG=2A,
VIN Clamp=4.5V, L = 1.2 µH, TA = +25ºC, unless otherwise noted.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
7
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN = 5.0V, VBATT = Full Range, Default Mode, IIN Limit=2A, VSYS=4.4V, R6 and R7 are float, ICHG=2A,
VIN Clamp=4.5V, L = 1.2 µH, TA = +25ºC, unless otherwise noted.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
8
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN = 5.0V, VBATT = Full Range, Default Mode, IIN Limit=2A, VSYS=4.4V, R6 and R7 are float, ICHG=2A,
VIN Clamp=4.5V, L = 1.2 µH, TA = +25ºC, unless otherwise noted.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
9
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN = 5.0V, VBATT = Full Range, Default Mode, IIN Limit=2A, VSYS=4.4V, R6 and R7 are float, ICHG=2A,
L = 1.2 µH, TA = +25ºC, unless otherwise noted.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
10
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN = 5.0V, VBATT = Full Range, Default Mode, IIN Limit=2A, VSYS=4.4V, R6 and R7 are float, ICHG=2A,
L = 1.2 µH, TA = +25ºC, unless otherwise noted.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
11
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN = 5.0V, VBATT = Full Range, Default Mode, IIN Limit=2A, VSYS=4.4V, R6 and R7 are float, ICHG=2A,
L = 1.2 µH, TA = +25ºC, unless otherwise noted.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
12
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
PIN FUNCTIONS
Package
Pin #
Name Description
Bootstrap. A capacitor is connected between SW and BST pin to form a floating supply
across the power switch driver to drive the power switch’s gate above the supply voltage.
1
BST
3
2,4
5
IN
Power input of the IC from adapter or USB.
SW
Switch output.
PGND Power ground.
_____
Function logic control pin of the IC. Logic low to enable the part and logic high to disable the
part.
6
EN
7
8
M0
M1
Mode Select Input Pin, in combination with M1 pin, setting the input current limit mode.
Mode Select Input Pin, in combination with M0 pin, setting the input current limit mode.
_____________
Open drain output. It is pulled low during charging. And it is pulled high through an external
resistor to VCC to indicate charge completed.
9
CHGOK
Open drain output. It is pulled low to indicate the presence of a valid input power supply.
Otherwise, it is pulled high through an external resistor to VCC to indicate invalid input or
removed input.
__________
10
ACOK
11
12
AGND Analog ground.
SYS voltage program pin. Connect a resistor divider from the pin to SYS and AGND to
SYSFB
program the system output voltage. Leave the pin float to disable the function.
13
14
SYS DC-DC regulator output to power the system load and charge the battery.
BATT Positive battery terminal.
Charge current program pin. A resistor from the pin to AGND can program the charge
current during CC charge. Float the pin will disable the charge function.
15
16
17
ISET
Thermistor input. Connect a resistor from this pin to VCC and the thermistor from this pin to
ground. The thermistor is usually inside the battery pack.
NTC
Input current limit program pin. A resistor from the pin to AGND can program the input
current limit with adapter input.
ILIM
18
19
20
TMR Set timer out period. Connect TMR pin to AGND to disable the internal timer.
VLIM Input voltage clamp program pin.
VCC Supply voltage of the IC.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
13
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
OPERATION
BST
IN
HSG
SYSFB1
EAO
EA
EA
3.6V
L
Converter
control
Max(A,B)
SW
SYS
VBATT+200mV
Driver
1
0
M
Input current
limit reference
selector
C
LSG
Iref
M
EAO
SYSFB
VBG
VREF
SYSFB
SYS
SYSFB
EA
ILIM
SYSFB1
VLIM
1.5V
mO
4 0
VBATx 2
Charge
Pump
VIN
Ideal diode
regulation
VTH
SYS
Battery switch
current limit
BATT
BATT
EN
3.5 V coarse
LDO &
EN
3.0 V UVLO
CC/ CV linear
charger
BATTFB
BATTFB
VBG
VREF_CC
VCC
Bandgap
& Bias
VBG
EN
4.5 V LDO
Charger Control & Chip Logic
UVLO
3.8 V UVLO
VIN
ISET
CHGOK
ACOK
TMR
NTC
GND
Figure 1—Function Block Diagram
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
14
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
the combination of the system load and battery
charger. The regulator contains input current
Introduction
The MP2617 is a switching charger IC, with
integrated smart power path management for
powering the system and charging a single cell
battery simultaneously and independently.
measurement and control scheme to ensure the
average input current remains below the level
programmed via ILIM pin or logic inputs M0&M1.
This meets the adapter capacity limit or stays in
compliance with USB specification.
The MP2617 includes a high-voltage (up to 14V)
input DC-DC step down converter for wide range
of DC sources and USB inputs. It has precision
average input current limit to make maximum use
of the allowable input power. This feature allows
fast charging when powering from an USB port,
and ensures the input current never exceeds the
input power specification especially when the
input power comes from a USB port. Additionally,
the input current limit threshold can be
programmed by logic inputs or a resistor to
ground from the ILIM pin.
When the input voltage is higher than UVLO and
310mV higher than the battery voltage, input
——————
voltage OK signal is active (ACOK turns low) and
the DC-DC converter soft-starts. If the input
power is sufficient to supply the combination of
the system load and battery charger, and the
input current limit loop is not triggered. The
converter output voltage VSYS will be regulated:
1) If BATT>3.4V, VSYS is approximately 0.2V
above the battery voltage to minimize the power
loss of the battery charger during fast charging.
The MP2617 implements an on-chip 40mꢀ
MOSFET which works as a full-featured linear
charger with trickle charge, high accuracy
constant current and constant voltage charge,
charge termination, auto recharge, NTC monitor,
built-in timer control, charge status indication,
and thermal protection. The charge current can
be programmed by an external resistor
connected from the ISET pin to AGND. The IC
limits the charge current when the die
temperature exceeds 120°C.
2) If BATT<3.4V, VSYS is fixed at 3.6V to power
the system immediately even when a drained
battery is inserted to be charged. Figure 2 shows
the relationship of VSYS vs. VBATT.
System voltage can also be regulated to any
value between 3.6V to 4.4V by using a resistor
divider on the SYSFB pin. This is shown as R6
and R7 in Figure 9. If the SYSFB is left floating,
the system program is invalid, and VSYS is
regulated as Figure 2.
The 40mꢀ MOSFET works as an ideal diode to
connecting the battery to the system load when
the input power is not enough to power the
system load. When the input is removed, the
40mꢀ MOSFET is turned on allowing the battery
to power up the system.
The converter adopts fixed off-time control to
extend the duty cycle (close to 100%) when the
input of the converter is close to VSYS.
4.4V
4.2V
With smart power path management, the system
load is satisfied in priority then the remaining
current is used to charge the battery. The
MP2617 will reduce charging current or even use
power from the battery to satisfy the system load
when its demand is over the input power capacity.
VSYS
200mV
3.6V
VBATT
Figure 1 shows the function block diagram of
MP2617.
DC-DC Step Down Converter
3.4V
4.2V
The DC-DC converter is a 1.6MHz constant
frequency step-down switching regulator to
provide the input power to the SYS, which drives
Figure 2 — SYS Regulation Output
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
15
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
Close to 100% duty operation, BST refresh
to control the operation duty. In this mode, the
input voltage will be clamped according to the
value set by the resistor divider. The control to
the system voltage and charge current is the
same as the one explained in the input current
limit. Charge current drops down to satisfy the
system current request first. This feature
provides a second protection to the input power
and ensures the safe operation of the input
adapter. Even if a wrong adapter is inserted, the
MP2617 can continue operation, providing the
maximum power to its load. User can program
the input voltage limit value through the resistor
divider from IN to VLIM to AGND.
operation makes sure the driver voltage of the
HS will be charged by turning on the LS until
negative IL hit about 400mA. If the input power is
insufficient to supply the combination of the
system load and battery charger, the DC-DC
converter will limit the total power requirement by
restricting the input voltage, input current and the
peak current through the MOSFET. The power
path management will reduce the charge current
to satisfy the external system load in priority.
According to this feature, the USB specification is
always satisfied first. Even if the charge current is
set larger than the USB input current limit, the
real charge current will be reduced as needed.
Peak Current Limit: The peak current of the high
side switch of the DC-DC converter is sensed
during every cycle, it is compared to the
reference 4.2A, if the peak current hits the
threshold, the peak current limit mode is
triggered. The control of the charge current is the
same with the above two limits.
Input Limit State
If the input power is insufficient to supply the
combination of the system load and battery
charger, the MP2617 implements three input limit
control loops to reduce the charge current and
satisfy the external system load in priority. The
input in this case might be limited as follows:
input current limit, input voltage limit and DC-DC
peak current limit.
Input Current Limit Setting
The current at ILIM is a precise fraction of the
adapter input current. When a programming
resistor is connected from ILIM to AGND, the
voltage on ILIM represents the average input
current of the PWM converter. And the input
current approaches the programmed limit, ILIM
voltage reaches 1.14V.
Input Current Limit: When the system current is
higher than the programmed input current limit
the input current limit loop takes the control of the
converter and regulates the input current at
constant value. When the battery voltage is over
3.4V, the output voltage (VSYS) will drop down
according to the increase of the system current,
and the charge current drops down after the
BATT-to-SYS switch (40mꢀ MOSFET) is fully on
according to VSYS dropping down. During this
process, the system voltage is slightly higher
than VBATT. When the battery voltage is lower
than 3.4V, to maintain the minimum system
voltage and ensure the system operation, the
input current limit control will pull down the
charge current directly to reduce the load of the
converter so that the system current is satisfied
in priority.
The average input current limit can be set
through the resistor connecting from ILIM to
AGND according to the following expression:
40000
IIN_LIM=1.14×
(mA)
RILIM(kꢀ)
When USB input, the input current limit is set
internally and the programmed value is invalid.
The MP2617 provides typical of 450mA input
current limit for USB2.0 specification and a
typical of 825mA for USB3.0 specification
respectively.
Input Voltage Limit: A resistor divider from IN pin
to VLIM pin to AGND is used for the input voltage
limit control. When the voltage on VLIM pin hits
the reference voltage of 1.52V, the output of the
input voltage limit error amplifier will drop in
The user can choose to set the input current limit
through the two logic pins M0 and M1 as shown
in Table 1 according to its input specification.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
16
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
When both M0 and M1 are float, they are pulled
to the logic high, under this condition, the input
current is limited to a default value of 2A.
the battery charger may or may not be able to
charge at the full programmed rate. The system
load is always satisfied first over the battery
charge current. If the system load requirement is
low, the battery can be charged at full constant
current.
Table 1―Input Current Limit Setting
M0
Low
Low
M1
Low
High
Mode
USB2.0 Mode
USB3.0 Mode
When the battery voltage reaches the battery full
threshold, the charger enters the “constant
voltage mode” operation.
High
Low
Programmable Mode
High/Float High/Float Default Mode
End of Charge (EOC) and Indication
In constant voltage charge mode, the battery
voltage is regulated at 4.2V (when SYSFB is float
or SYS is programmed higher than battery full
threshold) and the charge current decreases
naturally. Once the charge current hits the
battery full threshold IBF (1/10 programmed
charge current), the battery is fully charged and
charge cycle is terminated.
Input Voltage Limit Setting
The input voltage can be limited at a value set by
a resistor divider from IN pin to VLIM pin to
AGND according to the following expression
(Typical Application Circuit):
R1+R2
VIN_LIM=1.52×
(V)
R2
When the voltage on VLIM pin drops and hits the
reference voltage 1.52V, the input voltage will be
clamped to the setting value.
If the charge current drops below IBF because of
any limit condition, the MP2617 will come out of
CV mode, and the charge full detection is invalid.
Battery Charger
A safe timer starts at the beginning of each new
charge cycle and it monitors if the whole charge
period is within the programmed time limit. After
each charge cycle, when the battery is indicated
as full, the timer counter will be reset. If the time
is expired while the charging is still on going, the
The MP2617 completes charge operation consist
of trickle charge, automatic charge termination,
charge status indication, timer control, NTC
indication, automatic recharge, and thermal
limiting.
timer will force the MP2617 to terminate charging
_____________
When the PWM converter is out of soft start, the
battery charge cycle begins, the MP2617 first
determines if the battery is deeply discharged. If
the battery voltage is lower than the trick charge
threshold (typical 3.0V), the battery charger starts
in “trickle charge mode”. The trickle charge
current is limited to 10% of the programmed
charge current until the battery voltage reaches
3.0V. If the charge stays in the “trickle charging
mode” for longer than 45 minutes, the “timer out”
CHGOK is blinking to indicate the fault condition.
If system voltage is programmed lower than 4.2V
by the resistor divider at the SYSFB pin, the
battery will be charged most close to VSYS until
the charge current reaches the IBF threshold.
During charging, the PWM converter continues to
power the system at the same time, if the system
load increases over the input current limit, the
battery charger will change to “ideal diode mode”.
Two comparators between VSYS and VBATT are
used to detect this condition. If VSYS<VBATT-40mV
is triggered, the ideal diode mode is enabled,
else, if VSYS increases back to VSYS>VBATT+40mV,
the ideal diode mode is disabled as shown in
Figure 3.
condition is triggered, the charge is terminated
_____________
and CHGOK will start blinking to indicate that the
battery is unresponsive. When the battery
voltage is above 3.0V, the charger is operating at
“constant current mode.” The current delivered to
the battery will try to reach the value
programmed by the ISET pin. Depending on the
available input power and system load conditions,
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
17
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
can be calculated by monitoring the ISET pin
voltage with the following formula:
VBATT-40mV
Enable Ideal Diode Mode
VISET
VSYS
IBATT
=
×ICHG
1.15
Disable Ideal Diode Mode
Additionally, the actual battery charge current
may be lower than the programmed current due
to limited input power available and prioritization
of the system load.
VBATT+40mV
Figure 3— Ideal Diode Mode Enable/Disable
Battery charge full current threshold IBF is set
internally at 10% of the programmed charge
current. However, IBF has a 150mA maximum
limit which can not be exceeded.
In summary, the terminal battery voltage is 4.2V
(typical) when SYSFB is float or programmed
higher than battery full threshold-4.2V, and VSYS
-
IBF×40mꢀ when SYSFB is connected to the
resistor divider- programmed lower than 4.2V.
Logic Control
The MP2617 has two separate enable control
pins.
Automatic Recharge
Once the battery charge cycle is completed, the
MP2617 turns off indicating the battery full status.
During this process, the battery power may be
consumed by the system load or self discharge.
If the input power is always on, to ensure the
battery not to be exhausted, the new charge
cycle will automatically begin when the battery
voltage falls below the auto-recharge threshold
VRCHG which is typically 4V when the SYSFB is
float, and 50mV lower if the SYSFB is connected
to a resistor divider. The timer will re-start when
the auto-recharge cycle begins.
_____
EN is a logic control pin that controls the
_____
operation of the whole IC. When EN is low, the
IC is enabled and the PWM converter output
_____
powers the system and the charger. When EN is
high, both the PWM converter and the charger
are disabled. The BATT to SYS switch turns fully
on to connect the battery to power the system.
The ISET pin can be also used to control the
operation of the charger. Setting ISET pin floating
will disable the charger function while the output
of PWM converter will continue supply power to
system. On the other hand, a resistor from ISET
to AGND will enable the charging at the
programmed charge current.
During the charge off state when the battery is
fully charged, if the input power is recycled, or
the EN signal is refreshed, the charge cycle will
re-start and the timer will refresh even if the
battery voltage is above the auto-recharge
threshold.
The logic control of the ISET pin of the MP2617
can be realized as Figure 4. In this way, the user
can choose logic low to be “on” signal or logic
high to be ”off” signal with a N-MOSFET.
Charge Current Setting
The charge current of the MP2617 is
programmed using a single resistor from ISET
pin to ground. The program resistor and charge
current are calculated using the following
equations:
ISET
OFF ON
RISET
1800
ICHG = 1.15×
(mA)
RSET(kΩ)
Figure 4— ISET Logic Control
At either constant current mode or constant
voltage mode, the voltage at the ISET pin is
proportional to the actual charge current
delivered to the battery, IBATT. The charge current
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
18
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
__________
keeps low to avoid providing false charge full
Input Power Status Indication (ACOK)
indication.
__________
_____________
An internal under voltage lockout circuit monitors
the input voltage and keeps the IC in off state
until the input rises over the rising threshold
(3.8V). When the input voltage decreases below
threshold (3.5V), the IC will turn off, and the
Table 2 shows the ACOK and CHGOK status
under different charge conditions.
Table 2―Charger Status Indication
Charger Status
ACOK
CHGOK
system load will be powered by the battery
In charging, supplement
mode
__________
low
low
automatically. ACOK is an open-drain, active-
low output that indicates the status of input power.
The input is considered valid when the input
voltage is over the UVLO rising threshold, and
310mV higher than the battery voltage to ensure
both the converter and the charger can operate
End of charge, ISET
disable charger only.
low
low
high
blinking at
6Hz
NTC fault, timer out
VIN absent, EN disable,
thermal shutdown
high
high
normally. If the input voltage from an adapter or
__________
from a USB port is indicated OK, ACOK will turn
Timer Setting
low.
_____
During EN off or thermal shutdown conditions,
The MP2617 uses an internal timer to terminate
charge if the timer times out. The timer duration
is programmed by an external capacitor at the
TMR pin and related to the real charge current.
__________
the ACOK turns high to indicate no power is
__________
provided by the input to the system. The ACOK
signal indicates if input supplies power to the
The trickle mode charge time is:
CTMR
system load or not. Any other condition can not
__________
affect the ACOK indication as long as the input
power is present.
tTrickle _ TMR = 45×
(min) (ICHG = 1A)
0.1μF
_____________
The total charge time is:
Charge Status Indication (CHGOK)
_____________
CTMR
tTotal_TMR = 6.5×
0.1μF
CHGOK is an open-drain, active-low output that
(hr) (ICHG = 1A)
_____________
indicates the status of charge. CHGOK will be
low during normal charging operation, turn high
after charge full, and blink if a fault condition
happens including NTC fault (battery temperature
invalid) and timer out (bad battery).
The above equations are based on 1A charge
current. As a result of power path management
control, charge current might vary during normal
operation, under this condition, the MP2617
automatically takes into account this variation
and adjust the timer period accordingly.
_____________
In the event of a fault condition, CHGOK
switches at 6Hz with the 50% duty cycle and
enter “blinking” mode. The user should check the
application circuit to find out the root cause of the
When the charge current is set larger than 1A,
the safe timer period is reduced accordingly with
the same TMR capacitor. If the charge current is
reduced because of insufficient input power, the
timer period is increased proportionally by the
same rate at which the charge current is reduced.
If charge is stopped due to high system load, the
timer is temporarily suspended.
fault condition if the “blinking” signal is asserted.
_____________
For no battery condition, CHGOK is blinking
according to the transition between charging and
charge full. The blinking frequency is determined
by the cycle of charge and discharge of the
output capacitor.
This feature avoids indicating a false trigger
indication for bad battery indication when there is
little charge current delivered to the battery as a
result of the insufficient input power.
When the charge current to the battery is low or
in the event the battery is in supplement mode
_____________
caused by the insufficient input power, CHGOK
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
19
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
above 150oC as the IC enters thermal shutdown
protection.
When the timer out condition occurs, the MP2617
_____________
terminates the charge at once and CHGOK
Ideal Diode Mode
blinks to indicate the fault status. If one of the
following events happens, the timer is refreshed
and MP2617 re-starts the charge cycle.
If the system current requirement increases over
the preset limit of the PWM converter, the
additional current will be drawn from the battery
via the BATT-to-SYS switch. To avoid very large
currents being drawn from the battery which
might affect the reliability of the device, the
MP2617 controls the charge switch to work at the
ideal diode mode regulating VSYS to VBATT-65mV
when VSYS is 40mV lower than VBATT is detected.
Only when VSYS is 40mV higher than VBATT, the
charger switch exits the ideal diode mode, and
the charge cycle softly restarts.
•
Input re-startup
_____
•
•
Refresh EN /ISET signal
Auto-Recharge
NTC Thermistor
The NTC pin allows MP2617 to sense the battery
temperature using the Negative Thermal
Coefficient (NTC) thermistor usually available in
the battery pack to ensure safe operating
environment of the battery. A resistor with
appropriate value should be connected from VCC
to NTC and the NTC resistor is from NTC pin to
AGND. The voltage on NTC pin is determined by
the resistor divider whose divide ratio as the
different resistance of the NTC thermistor
depends on the ambient temperature of the
battery.
Battery Discharge Protection
When the input power is removed or invalid, the
system load will draw power from the battery via
the battery switch. Under this condition, the
battery switch is fully on to minimize the power
loss. The MP2617 integrates battery discharge
protection. If the battery discharge current is
larger than the discharge current limit threshold
IDIS (3.3A), the current will be regulated at the
preset limited value. And if the current increases
further, the SYS voltage starts to decrease.
When VSYS drops to about 800mV lower than
The MP2617 has an internal NTC voltage
comparator to set the upper and lower limit of the
divide ratio. If NTC pin voltage falls out of this
range it means the temperature is outside the
safe operating range,
VBATT, SYS short condition is detected. Under this
condition, the discharge current is limited at
200mA. In the event of a short from system to
GND the discharge current from the battery to
the system is also limited to 200mA.
As a result, The MP2617 will stop charging and
report it on indication pins. Charging will
automatically resume after the temperature falls
back into the safe range.
Furthermore, battery voltage UVLO is always
monitored. If the battery voltage is lower than the
battery UVLO threshold, the battery switch is
turned off immediately. This feature makes sure
the battery from over-discharged.
Thermal Protection
The MP2617 implements thermal protection to
prevent the thermal damage to the IC or
surrounding components. An internal thermal
sense and feedback loop will automatically
decrease the charge current when the die-
temperature rises to about 120oC. This function is
referred as charge current thermal fold-back.
This feature protects the MP2617 from excessive
temperature due to high power operation or high
ambient thermal conditions. Another benefit of
this feature is charge current can be set
according to the requirement rather than worst-
case conditions for a given application with the
assurance of safe operation. The MP2617 will
stop charging if the junction temperature rises
Dynamic Power Path Management (DPPM)
In the presence of a valid input source, the PWM
converter will supply the current to both the
system and the battery charger.
The voltage VSYS is regulated based on the value
of the battery voltage. When VBATT is higher than
3.4V, VSYS is regulated 200mv above VBATT to
charge the battery. When VBATT is lower than
3.4V, to ensure the system can still be powered
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
20
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
via an on-chip 40mꢀ MOSFET working as an
ideal diode.
up even with a drained battery connected, VSYS is
regulated at constant 3.6V.
Additionally, if the input source is removed, the
MP2617 will turn on the 40mꢀ MOSFET allowing
the battery to power the system load to keep the
operation of the portable device.
When the input source is overloaded, either the
current exceeds the input current limit or the
voltage falls below the input voltage limit, the
MP2617 then reduces the charge current until
the input current falls below the input current limit
and the input voltage rises above the input
voltage limit. If the system current increases
beyond the power allowed by the input source,
additional power will be drawned from the battery
Operation Flow Chart
Figure 5 shows the operation flow chart of the
MP2617.
Figure 6 shows the operation process.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
21
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
POR
Chip Enable?
No
Yes
VIN>3.0V?
No,
POR="1"
Yes,
POR="0"
Enable BG
Yes
Battery power system
Enable discharge limit
VBATT>VBATT_UVLO
?
BGOK="0"
BGOK="1"
No
Enable VREF LDO
System shuts down
No power to system
VIN>VIN_UVLO (VTH)?
No,
UVLO="1"
Yes,
UVLO="0"
VIN>VBATT+310mV?
No
Yes
Enable DC-DC
DC-DC soft starts
VSYS_REF=max(VBATT
+
200mV,3.6V)
VSYS>VBATT
ISET OK?
?
No
Yes
BATT-to-SYS
switch turns off
DC-DC starts ready?
No
Yes
Enable Battery
Charger
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
22
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
Yes
Clamp DC-DC
EAO to regulate
the part
Any Limit condition
triggered?
at the limit state
No
VBATT<3.4V?
VBATT>3.0V?
Yes
No
Yes
No
Trickle Charge
ICHG=10%ICC
VSYS drops down,
Charge switch
is fully on
Decrease ICHG
Keep VSYS=3.6V
,
CC/CV Charge
Yes
No
Satisfy System current
Charge the battery with
remaining current
No
Limit condition
Removed?
ICHG=IBF
?
No
Yes
Disable
Ideal Diode Mode
Charge in
CV mode and
ICHG<IBF?
No
No
Charge Full, EOC=1
TMR off,
Yes
ICHG=0?
Yes
clear the counter
DC-DC keeps work
Yes
No
No
VSYS>VBATT+40mV?
VSYS<VBATT-40mV?
Yes
VSYS<VBATT-40mV?
No
Yes
Yes
VBATT>VBATT_UVLO
?
No
Yes
VBATT<VRCHG
?
Ideal Diode Mode:
Battery switch shuts down,
DC-DC in over load
condition,
VSYS=VBATT-65mV,
Enable discharge
current limit
VSYS drops down
Figure 5— MP2617 Operation Flow Chart under No Fault Condition
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
23
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
Normal
operation
voltage
UVLO
Threshold-Hys
UVLO
Thresohold
VIN
0
Power Path Management
Battery
Supplement
Mode
ISYS
0
CV Charge
CC Charge
Trickle Charge
Battery
Full
IBATT
0
ISYS -IIN_LIM
Input Power
Current Limit
IIN_LIM
IIN_AVE
0
Supplement
Mode-
Discharging
Auto-
Recharging
Self-
discharging
Power off-
discharging
Charging
Charging
V
BATT=4.0V
VSYS
VBATT
VBATT=3.4V
V
BATT=3.0V
0
Figure 6— MP2617 Operation Process under No Fault Condition
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
24
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
APPLICATION INFORMATION
COMPONENT SELECTION
3A
2A
1A
Setting the Input Current Limit
ICC_MAX
Connect a resistor from the ILIM pin to AGND
to program the input current limit for different
input ports. The relationship between the input
current limit and setting resistor is as following:
40000
I
= 1.14×
(mA)
(1)
IN
RILIM(kΩ)
Where RILIM is greater than 15.2kꢀ, so that IILIM
is not over 3A.
3V
4.2V
Battery Voltage
Figure 7—ICHG Variation with Different Input
Current Limit
For USB input, the input current limit is set by
the M0 and M1 logic, the setting resistor by
ILIM pin is invalid.
Setting the Input Voltage Limit
Setting the Charge Current
RISET connecting from the ISET pin to AGND
sets the charge current (ICHG). The relationship
between the charge current and setting resistor
is as following:
The input clamp voltage is set using a resistive
voltage divider from the input voltage to VLIM
pin. The voltage divider divides the input
voltage down to the limit voltage by the ratio:
R2
1800
VVLIM = V
×
(V)
(4)
IN_LIM
ICHG = 1.15×
(mA)
(2)
R1+R2
RSET(kΩ)
Thus the input voltage is:
VIN_LIM = VVLIM
Assume ICHG=2A, thus: RISET=1.05kꢀ.
R1+R2
R2
×
(V)
(5)
Usually in USB mode, the charge current is
always set over the USB input limit specification.
Then the MP2617 regulates the input current
constant at the limitation value. Thus the real
CC charge current is not the setting value, it
varies with different input and battery voltages.
The maximum CC charge value can be
calculated as:
The voltage clamp reference voltage VVLIM is
1.52V, and a typical value for R2 can be 10kꢀ.
With this value, R1 can be determined by:
V
IN_LIM - V
R1=R2×
VLIM (V)
(6)
VVLIM
For example, for a 4.65V input limit voltage, R2
is 10kꢀ, and R1 is 20.6kꢀ.
V ×IILIM ×η
IN
ICC _ MAX
=
(A)
(3)
VTC
Setting the System Voltage
Where VTC is trickle charge threshold (3V) and η
is the current charge efficiency. Assume
VIN=5.5V, IILIM=1.5A, η=83%, thus ICC_MAX=2.28A.
Figure 7 shows a calculating charge current
curve by limiting the input current limit.
The system voltage can be regulated to any
value between 3.6V to 4.4V by the resistor
divider on SYSFB pin as R6 and R7 in Figure 9.
R6 + R7
VSYS = VSYS _ REF
×
(7)
R7
Where VSYS_REF is 1.152V, the reference voltage
of SYS. With a typical value for R7, 10kꢀ, R6
can be determined by:
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
25
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
maximum ripple current is 1A. Select the input
VSYS − V
R6 = R7×
SYS _REF (V)
(8)
capacitors so that the temperature rise due to
the ripple current does not exceed 10°C. Use
ceramic capacitors with X5R or X7R dielectrics
because of their low ESR and small
temperature coefficients. For most applications,
use a 22µF capacitor.
VSYS _REF
For example, for a 4.2V system voltage, R7 is
10kꢀ, and R6 is 26.5kꢀ.
Selecting the Inductor
Inductor selection trades off among cost, size,
and efficiency. A lower inductance value
corresponds to a smaller size, but results in
higher ripple currents, higher magnetic
Selecting the Output Capacitor
The output capacitor C2 from the typical
application circuit is in parallel with the SYS
load. C2 absorbs the high-frequency switching
ripple current and smoothes the output voltage.
Its impedance must be much less than that of
the system load to ensure it properly absorbs
the ripple current.
hysteretic
losses,
and
higher
output
capacitances. Choosing a higher inductance
value benefits from lower ripple current and
smaller output filter capacitors, but results in
higher inductor DC resistance (DCR) loss. From
a practical standpoint, the inductor ripple
current does not exceed 30% of the maximum
load current under worst cases conditions. For
the MP2617 operating with a typical 5V input
voltage, the maximum inductor current ripple
occurs at the corner point between trickle
charge and CC charge (VBATT=3V). Estimate the
required inductance as:
Use a ceramic capacitor because it has lower
ESR and smaller size that allows us to ignore
the ESR of the output capacitor. Thus, the
output voltage ripple is given by:
VSYS
1−
ΔVSYS
VSYS
V
IN
(12)
Δr =
=
%
8× C2× fS2 ×L
In order to guarantee the ±0.5% system voltage
accuracy, the maximum output voltage ripple
must not exceed 0.5% (e.g. 0.1%). The
maximum output voltage ripple occurs at the
minimum system voltage and the maximum
input voltage.
V − VBATT
ΔIL _ MAX V × fS(MHz)
VBATT
IN
L =
(μH)
(9)
IN
%ripple
IPEAK = ILOAD(MAX) ×(1+
)(mA)
(10)
2
Where VIN, VBATT, and fS are the typical input
voltage, the TC to CC charge threshold, and the
switching frequency, respectively. ΔIL_MAX is the
maximum inductor ripple current, which is
usually 30% of the CC charge current.
For
VIN=14V,
VSYS_MIN=3.6V,
L=1.2µH,
fS=1.6MHz, Δr =0.1%, the output capacitor can
be calculated as:
VSYS _MIN
1−
For ICHG=2A, VIN=5V, VBATT=3V and fs=1.6MHz,
the calculated inductance is 1.3µH. The
maximum inductor peak current exceeds 2.3A.
To optimize efficiency, chose an inductor with a
DC resistance less than 50mꢀ. Choose the
inductor 7447745012 from Wurth with ratings at
L=1.2µH/4.6A /21mꢀ.
V
IN
(13)
C2 =
8× fS2 ×L × Δr
We can then choose a 22µF ceramic capacitor.
Resistor Choose for NTC Sensor
Figure 8 shows an internal resistor divider
reference circuit to limit the low temperature
threshold and high temperature threshold at
65%·VCC and 33.5%·VCC, respectively. For a
given NTC thermistor, select appropriate RT1
and RT2 to set the NTC window.
Selecting the Input Capacitor
The input capacitor C1 from the typical
application circuit absorbs the maximum ripple
current from the PWM converter, which is given
by
VTC × (V
− VTC )
IN _ MAX
(A) (11)
IRMS _ MAX = ICC _ MAX
×
V
IN _ MAX
For ICC_MAX=2A, VTC=3V, VIN_MAX=14V, the
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
26
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
RT2//RNTC_Cold
V
PCB Layout Guideline
(14)
(15)
=
TH_Low =65%
RT1 +RT2//RNTC_Cold VCC
It is important to pay special attention to the
PCB layout to meet specified noise, efficiency
and stability requirements. The following design
considerations can improve circuit performance:
RT2//RNTC_Hot
VTH_High
VCC
=
= 33.5%
RT1 +RT2//RNTC_Hot
1) Route the power stage adjacent to their
grounds. Aim to minimize the high-side
switching node (SW, inductor), trace lengths in
the high-current paths and the current sense
resistor trace.
RNTC_Hot is the value of the NTC resistor at high
temperature of the required temperature
operation range, and RNTC_Cold is the value of
the NTC resistor at low temperature.
The two resistors, RT1 and RT2, allow the high
temperature limit and low temperature limit to
be programmed independently. With this
feature, the MP2617 can fit most type of NTC
resistor and different temperature operation
range requirements.
Keep the switching node short and away from
all small control signals, especially the feedback
network.
Place the input capacitor as close as possible
to the IN and PGND pins.
RT1 and RT2 values depend on the type of the
NTC resistor:
Place the output inductor close to the IC and
connect the output capacitor between the
inductor and PGND of the IC.
0.3×RNTC_Cold×RNTC_Hot
(16)
RT2
=
0.1225×RNTC_Cold-0.4225×RNTC_Hot
0.3×RNTC_Hot ×RNTC_Cold
2) For high-current applications, the balls for the
power pads (IN, SW, SYS, BATT and PGND)
should be connected to as much copper in the
board as possible. This improves thermal
performance because the board conducts heat
away from the IC.
(17)
RT1 =
0.2275×(RNTC_Cold −RNTC_Hot
)
For example, for the thermistor NCP18XH103,
it has the following electrical characteristic:
At 0°C, RNTC_Cold = 27.445kꢀ;
At 50°C, RNTC_Hot = 4.1601kꢀ.
3) The PCB should have a ground plane
connected directly to the return of all
components through vias (two vias per
capacitor for power-stage capacitors, one via
per capacitor for small-signal components). It is
also recommended to put vias inside the PGND
pads for the IC, if possible. A star ground
design approach is typically used to keep circuit
block currents isolated (high-power/low-power
small-signal) which reduces noise-coupling and
ground-bounce issues. A single ground plane
for this design gives good results. With this
small layout and a single ground plane, there is
no ground-bounce issue, and having the
components segregated minimizes coupling
between signals.
The following equations are derived assuming
that the NTC window is between 0°C and 50°C.
According to the above equations to calculate
RT1=6.47kꢀ and RT2=21.35kꢀ.
VCC
Low Temp Threshold
RT1
VTH_Low
NTC
RNTC
RT2
High Temp Threshold
VTH_High
Figure 8—NTC Function Block
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
27
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
TYPICAL APPLICATION CIRCUITS
Adapter /USB input
ON
OFF
C1
IN
M0 M1 EN
SYS
R1
R2
R6
R7
VLIM
ILIM
SYSFB
SYS Load
R
ILIM
SW
BST
L
C6
MP2617
C2
R4
R5
CHGOK
ACOK
VCC
VBAT
BATT
Battery
C3
R3
ISET
C5
NTC
RISET
TMR GND
C4
RNTC
Figure 9—Typical Charge Application Circuit with VSYS Programmed by SYSFB Pin
Adapter /USB input
ON
OFF
C1
IN
M0 M1 EN
SYS
R1
R2
R6
R7
VLIM
ILIM
SYSFB
SYS Load
R
ILIM
SW
BST
L
C6
MP2617
C2
R4
R5
CHGOK
ACOK
VCC
BATT
C3
R3
ISET
C5
NTC
RISET
TMR GND
C4
RNTC
Figure 10—Application with Charger Disabled under No Battery Condition
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
28
MP2617 – SINGLE CELL SWITCHING CHARGER WITH POWER PATH CONTROL
PACKAGE INFORMATION
QFN20-3X4mm
PIN 1 ID
MARKING
PIN 1 ID
0.10 X 45?TYP
PIN 1 ID
INDEX AREA
TOP VIEW
BOTTOM VIEW
SIDE VIEW
0.10 X 45?
NOTE:
1) ALL DIMENSIONS ARE IN MILLIMETERS.
2) EXPOSED PADDLE SIZE DOES NOT INCLUDE
MOLD FLASH.
3) LEAD COPLANARITY SHALL BE0.10
MILLIMETERS MAX.
4) JEDEC REFERENCE IS MO-220.
5) DRAWING IS NOT TO SCALE.
RECOMMENDED LAND PATTERN
NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third
party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not
assume any legal responsibility for any said applications.
MP2617 Rev. 1.03
8/23/2013
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2013 MPS. All Rights Reserved.
29
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00340/img/page/MP2617H_2093886_files/MP2617H_2093886_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00340/img/page/MP2617H_2093886_files/MP2617H_2093886_2.jpg)
MP2617H
Wide input Voltage, 3A, Switching Charger With NVDC Power Path Management For Single Cell Li Battery
MPS
![](http://pdffile.icpdf.com/pdf2/p00340/img/page/MP2617H_2093886_files/MP2617H_2093886_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00340/img/page/MP2617H_2093886_files/MP2617H_2093886_2.jpg)
MP2617HGL
Wide input Voltage, 3A, Switching Charger With NVDC Power Path Management For Single Cell Li Battery
MPS
![](http://pdffile.icpdf.com/pdf2/p00259/img/page/MP2618EV-LF_1563168_files/MP2618EV-LF_1563168_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00259/img/page/MP2618EV-LF_1563168_files/MP2618EV-LF_1563168_2.jpg)
MP2618EV-LF
Power Supply Support Circuit, Adjustable, 1 Channel, 4 X 5 MM, ROHS COMPLIANT, MO-220VHGD-3, QFN-28
MPS
![](http://pdffile.icpdf.com/pdf2/p00304/img/page/MP2618EV-LF-_1834031_files/MP2618EV-LF-_1834031_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00304/img/page/MP2618EV-LF-_1834031_files/MP2618EV-LF-_1834031_2.jpg)
MP2618EV-LF-Z
Power Supply Support Circuit, Adjustable, 1 Channel, 4 X 5 MM, ROHS COMPLIANT, MO-220VHGD-3, QFN-28
MPS
![](http://pdffile.icpdf.com/pdf2/p00341/img/page/MP2619_2097174_files/MP2619_2097174_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00341/img/page/MP2619_2097174_files/MP2619_2097174_2.jpg)
MP2619
2A, 24V Input, 600kHz 2-3 Cell Switching Li-Ion Battery Charger With System Power Path Management
MPS
![](http://pdffile.icpdf.com/pdf2/p00341/img/page/MP2619_2097174_files/MP2619_2097174_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00341/img/page/MP2619_2097174_files/MP2619_2097174_2.jpg)
MP2619EV
2A, 24V Input, 600kHz 2-3 Cell Switching Li-Ion Battery Charger With System Power Path Management
MPS
![](http://pdffile.icpdf.com/pdf2/p00341/img/page/MP2624_2097177_files/MP2624_2097177_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00341/img/page/MP2624_2097177_files/MP2624_2097177_2.jpg)
MP2624
I2C Controlled 4.5A Single Cell USB / Adaptor Charger with Narrow VDC Power Path Management USB OTG and Shipping Mode
MPS
![](http://pdffile.icpdf.com/pdf2/p00341/img/page/MP2624A_2097181_files/MP2624A_2097181_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00341/img/page/MP2624A_2097181_files/MP2624A_2097181_2.jpg)
MP2624A
4.5A, I2C-Controlled, Single-Cell USB/Adaptor Charger with Narrow VDC Power-Path Management USB OTG and SYS Reset Function
MPS
©2020 ICPDF网 联系我们和版权申明