10CE-5G0R/C03 [MSYSTEM]
High-density Signal Conditioners 10-RACK;
| 型号： | 10CE-5G0R/C03 |
| 厂家： | 
M-SYSTEM |
| 描述： | High-density Signal Conditioners 10-RACK |
| 文件： | 总3页 (文件大小：93K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: 10CE
F: 0 – 10 mA DC (Load resistance 1200 Ω max.)
High-density Signal Conditioners 10-RACK
G: 0 – 1 mA DC (Load resistance 12 kΩ max.)
Voltage
CT TRANSMITTER
(RMS sensing)
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)
3: 0 – 1 V DC (Load resistance 100 Ω min.)
4: 0 – 10 V DC (Load resistance 1000 Ω min.)
5: 0 – 5 V DC (Load resistance 500 Ω min.)
6: 1 – 5 V DC (Load resistance 500 Ω min.)
Functions & Features
• Converting an alternating current from a current
transformer into two standard process signals
• Minimum ripple
• Optional second channel output available at the front
terminals and at the Standard Rack connector
[3] OUTPUT 2
0: None
Typical Applications
Voltage
• Centralized monitoring and control of motors, pumps or
heaters by DCS
6: 1 – 5 V DC (Load resistance 5000 Ω min.)
• Monitoring power line and power supply current
POWER INPUT
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[4] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
MODEL: 10CE–[1][2][3]–R[4]
/C03: Rubber coating
ORDERING INFORMATION
• Code number: 10CE-[1][2][3]-R[4]
Specify a code from below for each [1] through [4].
(e.g. 10CE-1A6-R/Q)
GENERAL SPECIFICATIONS
Construction: Rack-mounted; terminal access via screw
terminals at the front and via card-edge connector at the
rear; terminal cover provided
• Specify the specification for option code /Q
(e.g. /C01)
Connection
Input: M3.5 screw terminals (torque 0.8 N·m)
Output: Card-edge connector and M3.5 screw terminals
(torque 0.8 N·m)
[1] INPUT
Current
Power input: Supplied from card-edge connector
Screw terminal: Nickel-plated steel
1: 0 – 1 A AC
5: 0 – 5 A AC
Housing material: Flame-resistant resin (black)
Isolation: Input to output 1 to output 2 to power
Input waveform: Up to 15 % of 3rd harmonic content
Overrange output: Approx. 0 to 120 % at 1 – 5V
Zero adjustment: -5 to +5 % (front)
[2] OUTPUT 1
Current
A: 4 – 20 mA DC (Load resistance 600 Ω max.)
B: 2 – 10 mA DC (Load resistance 1200 Ω max.)
C: 1 – 5 mA DC (Load resistance 2400 Ω max.)
D: 0 – 20 mA DC (Load resistance 600 Ω max.)
E: 0 – 16 mA DC (Load resistance 750 Ω max.)
Span adjustment: 95 to 105 % (front)
INPUT SPECIFICATIONS
Frequency: 50 or 60 Hz
Input burden: 0.5 VA max.
http://www.m-system.co.jp/
10CE SPECIFICATIONS
ES-0854 Rev.1 Page 1/3
MODEL: 10CE
Overload capacity: 500 % of rating for 5 sec., 120 %
continuous
Operational range: 0 – 120 % of rating
INSTALLATION
Current consumption: Approx. 35 mA with voltage output 1
Approx. 55 mA with current output 1
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Standard Rack 10BXx
Weight: 200 g (0.44 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.4 %
Temp. coefficient: ±0.02 %/°C (±0.01 %/°F)
Response time: ≤ 0.5 sec. (0 – 90 %)
Ripple: 0.5 %p-p max. (100/120 Hz)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength:
2000 V AC @ 1 minute (input to output 1 or output 2 or
power)
500 V AC @ 1 minute (output 1 to output 2 to power)
1500 V AC @ 1 minute (input or output or power to ground)
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
7–M3.5 SCREW
8 (.31)
2–4.3 (.17) dia.
MTG HOLE
TERMINAL COVER
1
5
2
6
3
7
8
3 (.12)
25 (.98)
51 (2.01)
130 (5.12)
http://www.m-system.co.jp/
10CE SPECIFICATIONS
ES-0854 Rev.1 Page 2/3
MODEL: 10CE
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
SOURCE
Z
S
Isolation
K
k
Low Drift
Amplifier
RMS
Operation
Output
Driver
1
2
3
7
8
+
–
OUTPUT 1
OUTPUT 2
CT
l
L
Z
S
LOAD
Voltage/
Duty Cycle
Output
Driver
5
6
+
–
Isolation
OUTPUT 2*
POWER
*1 output type has the output 1 connected to the card-edge connector in parallel.
Remark 1) The section enclosed by broken line is only for 2nd output channel.
Specifications are subject to change without notice.
http://www.m-system.co.jp/
10CE SPECIFICATIONS
ES-0854 Rev.1 Page 3/3
相关型号：
©2020 ICPDF网 联系我们和版权申明