10JF-AA0-R/1 [MSYSTEM]
High-density Signal Conditioners 10-RACK;型号: | 10JF-AA0-R/1 |
厂家: | M-SYSTEM |
描述: | High-density Signal Conditioners 10-RACK |
文件: | 总3页 (文件大小:103K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: 10JF
High-density Signal Conditioners 10-RACK
[2] OUTPUT 1
Current
A: 4 – 20 mA DC (Load resistance 600 Ω max.)
Voltage
2-input MATH FUNCTION MODULE
(field-programmable)
6: 1 – 5 V DC (Load resistance 500 Ω min.)
Functions & Features
• Providing temperature or pressure compensation for a gas
flow, and other arithmetic operations
• Microprocessor based
[3] OUTPUT 2
0: None
• Equation and parameters selectable on site via hand-held
programmer PU-2x
Voltage
6: 1 – 5 V DC (Load resistance 5000 Ω min.)
• Loop testing
• Optional second channel output available at the front
terminals and at the Standard Rack connector
POWER INPUT
DC Power
R: 24 V DC
Typical Applications
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
• Various flowmeters
• Adding two flows
[4] OPTIONS (multiple selections)
Equation (Refer to the EQUATION table)
/1: Temperature compensation for DP flowmeter (ideal gas)
/2: Pressure compensation for DP flowmeter (ideal gas)
/3: Addition/subtraction
• Ratio calculation
• Calculating average temperature
/4: Multiplication
/5: Division
Other Options
blank: none
/Q: Option other than the above (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
MODEL: 10JF-[1][2][3]-R[4]
/C03: Rubber coating
ORDERING INFORMATION
• Code number: 10JF-[1][2][3]-R[4]
Specify a code from below for each of [1] through [4].
(e.g. 10JF-6A6-R/3/Q)
• Parameters
Use Ordering Information Sheet (No. ESU 1980). Default
setting will be used if not otherwise specified.
(K0
= 1, K
1
= 1, K
2
= 1, A
0
= 0 %, A
1
= 0 %, A = 0 %)
2
• Specify the specification for option code /Q
(e.g. /C01)
[1] INPUT
Current
A: 4 – 20 mA DC (Input resistance 100 Ω)
Voltage
6: 1 – 5 V DC (Input resistance 1 MΩ min.)
10JF SPECIFICATIONS
ES-0880 Rev.11 Page 1/3
http://www.m-system.co.jp/
MODEL: 10JF
and parameters, square root extraction, zero and span, etc.
(Refer to the users manual of JXCON for the adjustments
configurable with JXCON.)
EQUATION
Equation parameters
X0: output (%)
X
1
to X
to K
to A
2
: input (%)
K0
2: gain ±29.999
INPUT SPECIFICATIONS
A0
2: bias (%) ±299.99 %
■ DC Current: Input resistor incorporated
EQUATION
/1: Temperature compensation for DP flowmeter (ideal gas)
INSTALLATION
K1X1
X0 =
K2X2+A2
Current consumption: Approx. 60 mA with voltage output 1
Approx. 90 mA with current output 1
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Standard Rack 10BXx
where X0 : compensated flow (linear characteristic)
X1 : uncompensated flow (square root extraction available)
X2 : temperature
/2: Pressure compensation for DP flowmeter (ideal gas)
X0 = K1X1 K2X2+A2
Weight: 220 g (0.49 lb)
where X0 : compensated flow (linear characteristic)
X1 : uncompensated flow (square root extraction available)
X2 : pressure
PERFORMANCE in percentage of span
Accuracy: Input accuracy + output accuracy
Input accuracy: ±0.2 % (gain ≤ 1)
/3: Addition/subtraction
X0 = K0 {K1 (X1+A1) + K2 (X2+A2)} + A0
/4: Multiplication
[±0.2 % × gain] with gain > 1
X0 = K0 (K1X1+A1) (K2X2+A2) + A0
Output accuracy: ±0.2 %
/5:Division
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Response time: ≤ 1.2 sec. (0 – 90 %)
0
K (K1X1+A1)
(K2X2+A2)
X0
=
+ A0
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 500 V AC @ 1 minute
(input to output 1 to output 2 to power)
1500 V AC @ 1 minute (input or output or power to ground)
RELATED PRODUCTS
• Programming Unit (model: PU-2x)
• PC configurator software (model: JXCON)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
GENERAL SPECIFICATIONS
Construction: Rack-mounted; terminal access via screw
terminals at the front and via card-edge connector at the
rear; terminal cover provided
Connection
Input: M3.5 screw terminals (torque 0.8 N·m)
Output: Card-edge connector and M3.5 screw terminals
(torque 0.8 N·m)
Power input: Supplied from card-edge connector
Screw terminal: Nickel-plated steel
Housing material: Flame-resistant resin (black)
Isolation: Input to output 1 to output 2 to power (non-
isolated between inputs)
Overrange input: Approx. -25 to +125 %
Overrange output: Approx. -10 to +120 % at 1 – 5 V
Adjustments: Programming Unit (model: PU-2x); equation
10JF SPECIFICATIONS
ES-0880 Rev.11 Page 2/3
http://www.m-system.co.jp/
MODEL: 10JF
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
7–M3.5 SCREW
8 (.31)
2–4.3 (.17) dia.
MTG HOLE
TERMINAL COVER
1
5
2
6
3
7
8
3 (.12)
25 (.98)
51 (2.01)
130 (5.12)
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Isolation
Digital
Output
Driver
+
–
+
1
2
3
7
8
+
–
Multiplexer
Computation
*
INPUT 1
INPUT 2
OUTPUT 1
OUTPUT 2
Z
S
Output
Driver
5
6
+
–
MODULAR JACK
PU-2x
SERIAL TRANSMISSION LINE
OUTPUT 2**
POWER
* Input shunt resistor incorporated for current input.
**1 output type has the output 1 connected to the card-edge connector in parallel.
Note: The section enclosed by broken line is only for 2nd output channel.
Specifications are subject to change without notice.
10JF SPECIFICATIONS
ES-0880 Rev.11 Page 3/3
http://www.m-system.co.jp/
相关型号:
©2020 ICPDF网 联系我们和版权申明