10JM-160-R/C02 [MSYSTEM]
High-density Signal Conditioners 10-RACK;
| 型号： | 10JM-160-R/C02 |
| 厂家： | 
M-SYSTEM |
| 描述： | High-density Signal Conditioners 10-RACK |
| 文件： | 总3页 (文件大小：93K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: 10JM
High-density Signal Conditioners 10-RACK
[1] OUTPUT 1
Current
A: 4 – 20 mA DC (Load resistance 600 Ω max.)
Voltage
POTENTIOMETER TRANSMITTER
(field-programmable)
6: 1 – 5 V DC (Load resistance 500 Ω min.)
Functions & Features
• Providing two DC outputs proportional to a potentiometer
or slidewire position input
[2] OUTPUT 2
• Microprocessor based
0: None
• Constant voltage excitation allows use with pots with total
resistances from 100 Ω – 10kΩ without affecting accuracy
• 75 % zero/span adjustments with minimal interaction
• Linearization data programmable via hand-held
programmer PU-2x
Voltage
6: 1 – 5 V DC (Load resistance 5000 Ω min.)
POWER INPUT
DC Power
• Loop testing via hand-held programmer PU-2x
• Optional second channel output available at the front
terminals and at the Standard Rack connector
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[3] OPTIONS
Typical Applications
blank: none
• Tank levels
/Q: With options (specify the specification)
• Positions
• Linearizing non-linear signal characteristics by the
sensor's linking mechanism
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
RELATED PRODUCTS
• Programming Unit (model: PU-2x)
• PC configurator software (model: JXCON)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
MODEL: 10JM–1[1][2]–R[3]
GENERAL SPECIFICATIONS
Construction: Rack-mounted; terminal access via screw
terminals at the front and via card-edge connector at the
rear; terminal cover provided
ORDERING INFORMATION
• Code number: 10JM-1[1][2]-R[3]
Specify a code from below for each [1] through [3].
(e.g. 10JM-1A6-R/Q)
Connection
• Linearization data (max. 16 points)
Use Ordering Information Sheet (No. ESU-1669) to specify
linearization data when the I/O signals are non-linear.
• Specify the specification for option code /Q
(e.g. /C01)
Input: M3.5 screw terminals (torque 0.8 N·m)
Output: Card-edge connector and M3.5 screw terminals
(torque 0.8 N·m)
Power input: Supplied from card-edge connector
Screw terminal: Nickel-plated steel
Housing material: Flame-resistant resin (black)
Isolation: Input to output 1 to output 2 to power
Linearization: 16 points max. within the range of -15.00 –
+115.00 % input or output; represented as percentage of
INPUT POTENTIOMETER
1: Total resistance 100 Ω – 10 kΩ
http://www.m-system.co.jp/
10JM SPECIFICATIONS
ES-0865 Rev.11 Page 1/3
MODEL: 10JM
full-scale
Adjustments: Programming Unit (model: PU-2x);
linearization data (Unused resistance of the potentiometer's
total resistance can be programmed with the linearization
table.), zero and span, simulating output, etc.
(Refer to the users manual of JXCON for the adjustments
configurable with JXCON.)
INPUT SPECIFICATIONS
Minimum span: 25 % of total resistance (set with the
Programming Unit [model: PU-2x] or PC configurator
software [model: JXCON])
Excitation: 0.25 V DC
INSTALLATION
Current consumption: Approx. 60 mA with voltage output 1
Approx. 90 mA with current output 1
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Standard Rack 10BXx
Weight: 220 g (0.49 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.1 % with segment gain ≤ 1 [±0.1 % × gain]
with segment gain > 1
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Response time: ≤ 0.5 sec. (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 500 V AC @ 1 minute
(input to output 1 to output 2 to power)
1500 V AC @ 1 minute (input or output or power to ground)
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
7–M3.5 SCREW
8 (.31)
2–4.3 (.17) dia.
MTG HOLE
TERMINAL COVER
1
5
2
6
3
7
8
3 (.12)
25 (.98)
51 (2.01)
130 (5.12)
http://www.m-system.co.jp/
10JM SPECIFICATIONS
ES-0865 Rev.11 Page 2/3
MODEL: 10JM
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
POTENTIOMETER
max.
Excitation Volt.
Generator
+
1
2
3
3
2
1
Isolation
Low Drift
Amplifier
Digital
Computation
Output
Driver
7
8
+
–
OUTPUT 1
OUTPUT 2
–
min.
Z
S
Output
Driver
5
6
+
–
MODULAR JACK
PU-2x
SERIAL TRANSMISSION LINE
OUTPUT 2*
POWER
*1 output type has the output 1 connected to the card-edge connector in parallel.
Remark 1) The section enclosed by broken line is only for 2nd output channel.
Specifications are subject to change without notice.
http://www.m-system.co.jp/
10JM SPECIFICATIONS
ES-0865 Rev.11 Page 3/3
相关型号：
©2020 ICPDF网 联系我们和版权申明