10SP-2A0-R 概述
High-density Signal Conditioners 10-RACK
10SP-2A0-R 数据手册
通过下载10SP-2A0-R数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MODEL: 10SP
F: 0 – 10 mA DC (Load resistance 1200 Ω max.)
High-density Signal Conditioners 10-RACK
G: 0 – 1 mA DC (Load resistance 12 kΩ max.)
Voltage
LOW FREQUENCY TRANSMITTER
(50 Hz minimum)
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)
3: 0 – 1 V DC (Load resistance 100 Ω min.)
4: 0 – 10 V DC (Load resistance 1000 Ω min.)
5: 0 – 5 V DC (Load resistance 500 Ω min.)
6: 1 – 5 V DC (Load resistance 500 Ω min.)
Functions & Features
• Converting the output from a pulse-type transducer into a
standard process signal
• Excitation
• Optional second channel output available at the front
terminals and at the Standard Rack connector
[3] OUTPUT 2
0: None
Typical Applications
Voltage
• Positive displacement flowmeters, turbine flowmeters and
vortex flowmeters
6: 1 – 5 V DC (Load resistance 5000 Ω min.)
• Proximity switches
POWER INPUT
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
[4] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
MODEL: 10SP–[1][2][3]–R[4]
/C03: Rubber coating
ORDERING INFORMATION
• Code number: 10SP-[1][2][3]-R[4]
Specify a code from below for each [1] through [4].
(e.g. 10SP-2A6-R/Q)
GENERAL SPECIFICATIONS
Construction: Rack-mounted; terminal access via screw
terminals at the front and via card-edge connector at the
rear; terminal cover provided
• Frequency range (e.g. 0 – 10 kHz)
• Specify the specification for option code /Q
(e.g. /C01)
Connection
Input: M3.5 screw terminals (torque 0.8 N·m)
Output: Card-edge connector and M3.5 screw terminals
(torque 0.8 N·m)
Power input: Supplied from card-edge connector
Screw terminal: Nickel-plated steel
[1] INPUT
1: Dry contact
2: Voltage pulse
Housing material: Flame-resistant resin (black)
Isolation: Input to output 1 to output 2 to power
Overrange output: Approx. 0 to 120 % at 1 – 5V
Zero adjustment: -5 to +5 % (front)
[2] OUTPUT 1
Current
Span adjustment: 95 to 105 % (front)
Input pulse sensing: DC coupled; detecting pulse rise
Low-end cutout: 2 to 5 %
A: 4 – 20 mA DC (Load resistance 600 Ω max.)
B: 2 – 10 mA DC (Load resistance 1200 Ω max.)
C: 1 – 5 mA DC (Load resistance 2400 Ω max.)
D: 0 – 20 mA DC (Load resistance 600 Ω max.)
E: 0 – 16 mA DC (Load resistance 750 Ω max.)
http://www.m-system.co.jp/
10SP SPECIFICATIONS
ES-0856 Rev.8 Page 1/3
MODEL: 10SP
INPUT SPECIFICATIONS
Excitation: 12 V DC @30 mA; shortcircuit protection
Frequency range: 0 – 50 Hz through 10 kHz
■ Dry Contact: Mechanical contact or open collector
Pulse width time requirement: 20 μsec. min. for ON and OFF
Sensing: Approx. 12 V DC @3 mA
ON/OFF level: ≤ 200 Ω / 0.6 V for ON, ≥ 100 kΩ / 6 V for OFF
■ Voltage Pulse: Square or sine waveforms
Pulse width time requirement: 20 μsec. min. for high and
low levels
Hi level: 2 – 50 V
Lo level: ≤ 1 V
Input impedance: 10 kΩ min.
INSTALLATION
Current consumption: Approx. 25 mA with voltage output 1
Approx. 45 mA with current output 1
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Standard Rack 10BXx
Weight: 200 g (0.44 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.1 % (output 10 – 100 %)
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)
Response time: (0 – 90%)
Approx. 1.8 sec. with 0 – 50 Hz
Approx. 0.7 sec. with 0 – 100 Hz
Approx. 0.5 sec. with 0 – 500 Hz
Approx. 0.5 sec. with 0 – 10 kHz
Ripple: 0.2 %p-p max. with input ≥ 10 %
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 500 V AC @ 1 minute
(input to output 1 to output 2 to power)
1500 V AC @ 1 minute (input or output or power to ground)
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
7–M3.5 SCREW
8 (.31)
2–4.3 (.17) dia.
MTG HOLE
TERMINAL COVER
1
5
2
6
3
7
8
3 (.12)
25 (.98)
51 (2.01)
130 (5.12)
http://www.m-system.co.jp/
10SP SPECIFICATIONS
ES-0856 Rev.8 Page 2/3
MODEL: 10SP
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Z
S
Isolation
Waveform
Shaper
Output
Driver
+
–
1
2
3
7
8
+
–
One-Shot
Smoother
INPUT
OUTPUT 1
OUTPUT 2
*
SENSOR EXCITATION
+
Z
S
12V Supply
Output
Driver
5
6
+
–
Isolation
OUTPUT 2**
POWER
* 4kΩ attached for dry contact input only.
**1 output type has the output 1 connected to the card-edge connector in parallel.
Remark 1) The section enclosed by broken line is only for 2nd output channel.
Specifications are subject to change without notice.
http://www.m-system.co.jp/
10SP SPECIFICATIONS
ES-0856 Rev.8 Page 3/3
10SP-2A0-R 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
10SP-2A6-R | MSYSTEM | High-density Signal Conditioners 10-RACK | 获取价格 | |
10SP-2B0-R | MSYSTEM | High-density Signal Conditioners 10-RACK | 获取价格 | |
10SP-2B6-R | MSYSTEM | High-density Signal Conditioners 10-RACK | 获取价格 | |
10SP-2C0-R | MSYSTEM | High-density Signal Conditioners 10-RACK | 获取价格 | |
10SP-2C6-R | MSYSTEM | High-density Signal Conditioners 10-RACK | 获取价格 | |
10SP-2D0-R | MSYSTEM | High-density Signal Conditioners 10-RACK | 获取价格 | |
10SP-2D6-R | MSYSTEM | High-density Signal Conditioners 10-RACK | 获取价格 | |
10SP-2E0-R | MSYSTEM | High-density Signal Conditioners 10-RACK | 获取价格 | |
10SP-2E6-R | MSYSTEM | High-density Signal Conditioners 10-RACK | 获取价格 | |
10SP-2F0-R | MSYSTEM | High-density Signal Conditioners 10-RACK | 获取价格 |
10SP-2A0-R 相关文章
- 2024-10-31
- 6
- 2024-10-31
- 6
- 2024-10-31
- 7
- 2024-10-31
- 8