18KBXC-K2 [MSYSTEM]
Rack-mounted DCS Signal Conditioners 18K-RACK;型号: | 18KBXC-K2 |
厂家: | M-SYSTEM |
描述: | Rack-mounted DCS Signal Conditioners 18K-RACK DCS 分布式控制系统 |
文件: | 总6页 (文件大小:205K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MODEL: 18KBXC
Rack-mounted DCS Signal Conditioners 18K-RACK
RELATED PRODUCTS
• Blank filler plate (model: P-181)
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN)
STANDARD RACK
Functions & Features
• Standard 19" rack for 18K-RACK signal conditioners
• 18-Rack signal conditioners are also mountable
• Module can be retracted without removing wiring for an
insulation test
GENERAL SPECIFICATIONS
Construction: Metal plates assembly
Coating: Colored Zn-Cr
• Line power supplied via the rear rack bus
• Direct interface to various DCS with the rack side
connector
Capacity: 16 positions
Connection
Power input: M4 screw terminals (torque 0.8 N·m)
Field terminal: M3.5 screw terminals (torque 0.8 N·m)
Screw terminal
Power: Nickel-plated brass
Field terminal: Nickel-plated steel
Isolation: I/O connector to field terminal to power to FG
INSTALLATION
Power input
•DC: Operating voltage range 24 V DC ±10 %, 2.5 A
minimum (ripple 10 % p-p max.)
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: JIS or EIA standard rack or surface
Weight: 2.7 kg (5.95 lb)
MODEL: 18KBXC–[1][2]
ORDERING INFORMATION
• Code number: 18KBXC-[1][2]
Specify a code from below for each [1] and [2].
(e.g. 18KBXC-Y1/W)
PERFORMANCE
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 500 V AC @ 1 minute
(I/O connector to field terminal to power)
1000 V AC @ 1 minute (I/O connector or field terminal or
power to FG)
[1] CONNECTOR
0: None
U1: Fujitsu FCN type I/O connector
Y1: Yokogawa DCS MAC2 / PAC card use
Y2: Yokogawa DCS VMx / PM1 card use
Y3: Yokogawa DCS for Module
• AAB841 (Adapter: ATV4A, Cable: KS2)
E4: Toshiba DCS VTBU card use
K1: Yamatake DCS AI connector
K2: Yamatake DCS AO connector
K5: Yamatake DCS PI connector
M-System guarantees the connecting section.
[2] OPTIONS
Mounting Bracket
blank: Rack mounting, standard
/W: Surface mounting
http://www.m-system.co.jp/
18KBXC SPECIFICATIONS
ES-0492 Rev.0 Page 1/6
MODEL: 18KBXC
MOUNTING REQUIREMENTS unit: mm (inch)
465 (18.31)
450 (17.72)
4–M5 SCREW
ANGLE BRACKET
Observe an appropriate wiring space over and below.
100 (3.94) for JIS standard
*
CONNECTION DIAGRAM
CN1
CN2
1
2
3
+
POWER
−
FG
Note 1: CN1 and CN2 are not available without connector.
Note 2: CN2 is only available with
• Fujitsu FCN type I/O connector
• Yokogawa DCS MAC2 / PAC card use
• Yokogawa DCS for Module / AAB841
(Adapter: ATV4A, Cable: KS2)
• Yamatake DCS PI connector
ꢀꢀ
ꢀꢀ
http://www.m-system.co.jp/
18KBXC SPECIFICATIONS
ES-0492 Rev.0 Page 2/6
MODEL: 18KBXC
DIMENSIONS unit: mm (inch)
■ RACK (standard)
■ SURFACE (option /W)
435 (17.13)
1
2
3
14 15 16
14 15 16
CN1
CN2
CONNECTOR
1
2
+
+
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
3
3-M4 POWER TERMINAL
465 (18.31)
480 (18.90)
64−M3.5
FIELD TERMINAL*
*Field I/O Terminal Block
1
2
1
2
1
2
8.2 (.32)
3
4
3
4
3
4
1ch
15ch 16ch
http://www.m-system.co.jp/
18KBXC SPECIFICATIONS
ES-0492 Rev.0 Page 3/6
MODEL: 18KBXC
I/O CONNECTOR PIN ASSIGNMENT
•
Yokogawa DCS for Module
•
Fujitsu FCN type I/O connector
(Fujitsu FCN-365P040-AU)
Connector Pin Assignment
AAB841 module (Adapter: ATV4A, Cable: KS2)*
(PS-40PE-D4LT1-PN1)
Location
CN1:
CN2:
output 1 or input
output 2
CN1:
CN2:
Single
Unused* *
PIN NO.
ASSIGNMENT
PIN NO.
ASSIGNMENT
The input or output 1 is connected to the connector.
The CN1 and CN2 are connected in parallel.
A 1
A 2
A 3
A 4
A 5
A 6
A 7
A 8
A 9
A10
A11
A12
A13
A14
A15
A16
ch. 1 +
ch. 2 +
ch. 3 +
ch. 4 +
ch. 5 +
ch. 6 +
ch. 7 +
ch. 8 +
ch. 9 +
ch.10 +
ch.11 +
ch.12 +
ch.13 +
ch.14 +
ch.15 +
ch.16 +
B 1
B 2
B 3
B 4
B 5
B 6
B 7
B 8
B 9
B10
B11
B12
B13
B14
B15
B16
ch. 1 –
ch. 2 –
ch. 3 –
ch. 4 –
ch. 5 –
ch. 6 –
ch. 7 –
ch. 8 –
ch. 9 –
ch.10 –
ch.11 –
ch.12 –
ch.13 –
ch.14 –
ch.15 –
ch.16 –
18K-RACK LOCATION NO.
7
1
1
2
2
3
3
4
4
5
6
8
9
10 11 12 13 14 15 16
5
6
7
8
1
2
3
4
5
6
7
8
AAB841 module INPUT NO.
AAB841 module OUTPUT NO.
Connector Pin Assignment (CN1, CN2)
PIN NO.
ASSIGNMENT
PIN NO.
ASSIGNMENT
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
ch. 1 +
ch. 1 –
ch. 2 +
ch. 2 –
ch. 3 +
ch. 3 –
ch. 4 +
ch. 4 –
ch. 5 +
ch. 5 –
ch. 6 +
ch. 6 –
ch. 7 +
ch. 7 –
ch. 8 +
ch. 8 –
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
ch. 9 +
ch. 9 –
ch.10 +
ch.10 –
ch.11 +
ch.11 –
ch.12 +
ch.12 –
ch.13 +
ch.13 –
ch.14 +
ch.14 –
ch.15 +
ch.15 –
ch.16 +
ch.16 –
A17 – A20, B17 – B20: Unused
Pin assignment is common to both CN1 and CN2.
•
Yokogawa DCS MAC2 / PAC card use
(PS-40PE-D4LT1-PN1)
Location
CN1:
CN2:
MAC2 / PAC card use*
MAC2 / PAC card use* (for redundancy)
The input or output 1 is connected to the connector.
18K-RACK LOCATION NO.
7
1 – 8: Unused
1
2
3
4
5
6
8
9
10 11 12 13 14 15 16
1
i
1
o
2
i
2
o
3
i
3
o
4
i
4
o
5
i
5
o
6
i
6
o
7
i
7
o
8
i
8
o
*I/O module
AAB841: Analog I/O module
(1 - 5 V input, 4 - 20 mA output,
MAC2/PAC CARD I/O (i = input, o = output)
input 8 points / output 8 points, non-isolated)
**Not available for redundancy
*MAC2 card (uses KS1 cable)
I/O card used for control I/O. Composed of 8 inputs
and 8 outputs. Input and output are paired. (Replace
with pulse inputs for PAC card.)
•Toshiba DCS VTBU card use (57LE-40360-7700)
Connector Pin Assignment
CN1:
VTBU card use
The output 1 is connected to the connector.
•
Yokogawa DCS VMx / PM1 card use
(PS-40PE-D4LT1-PN1)
Location
PIN NO.
ASSIGNMENT
PIN NO.
ASSIGNMENT
1
2
ch. 1 +
ch. 2 +
ch. 3 +
ch. 4 +
ch. 5 +
ch. 6 +
ch. 7 +
ch. 8 +
ch. 9 +
ch.10 +
ch.11 +
ch.12 +
ch.13 +
ch.14 +
ch.15 +
ch.16 +
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
ch. 1 –
ch. 2 –
ch. 3 –
ch. 4 –
ch. 5 –
ch. 6 –
ch. 7 –
ch. 8 –
ch. 9 –
ch.10 –
ch.11 –
ch.12 –
ch.13 –
ch.14 –
ch.15 –
ch.16 –
CN1:
VMx / PM1 card use*
3
4
5
6
7
8
The input or output 1 is connected to the connector.
18K-RACK LOCATION NO.
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10 11 12 13 14 15 16
10 11 12 13 14 15 16
VM1/PM1/VM4 CARD INPUT or OUTPUT
9
1
2
3
VM2 CARD INPUT NO.
4
5
6
7
8
1
2
3
VM2 CARD OUTPUT NO.
4
5
6
7
8
10
11
12
13
14
15
16
*VMx / PM1 card (uses KS2 cable)
VM1: analog input 16 points
VM2: analog input 8 points / analog output 8 points
VM4: analog output 16 points
17, 18, 35 and 36: Unused
PM1: pulse input 16 points
http://www.m-system.co.jp/
18KBXC SPECIFICATIONS
ES-0492 Rev.0 Page 4/6
MODEL: 18KBXC
Yamatake DCS AI connector
•
Yamatake DCS PI connector
•
Location
Location
Input connector: 57LE-40500-7300
Output connector: 57LE-40500-7300
CN1, CN2: PI use
CN1:
AI use
18K-RACK LOCATION NO.
18K-RACK LOCATION NO.
7
1
1
2
2
3
3
4
4
5
6
7
8
9
10 11 12 13 14 15 16
1
1
2
2
3
3
4
4
5
6
8
9
10 11 12 13 14 15 16
5
6
7
8
9
10 11 12 13 14 15 16
5
6
7
8
1
2
3
4
5
6
7
8
YAMATAKE DCS AI CARD (J-HAM50/HMM00) INPUT
CN1
CN2
YAMATAKE DCS PI CARD
(J-PIM00) INPUT
YAMATAKE DCS PI CARD
(J-PIM00) INPUT
Yamatake DCS AO connector
•
Location
Output connector: 57LE-40500-7300
Connector Pin Assignment (CN1, CN2)
CN1:
AO use
1, 36, 38, 39, 41, 42, 43 and 45 in CN1 and CN2 are connected.
2, 34, 35, 37, 40, 44, 46 and 47 in CN1 and CN2 are connected.
48 and 49 in CN1 and CN2 are connected.
18K-RACK LOCATION NO.
7
1
1
2
2
3
3
4
4
5
6
8
9
10 11 12 13 14 15 16
The output 1 is connected to the connector.
5
6
7
8
9
10 11 12 13 14 15 16
YAMATAKE DCS AO CARD (J-AOM10) OUTPUT
PIN NO.
(CN1)
ASSIGNMENT
PIN NO.
(CN2)
ASSIGNMENT
3
4
5
ch. 1 +
ch. 1 –
ch. 2 +
ch. 2 –
ch. 3 +
ch. 3 –
ch. 4 +
ch. 4 –
ch. 5 +
ch. 5 –
ch. 6 +
ch. 6 –
ch. 7 +
ch. 7 –
ch. 8 +
ch. 8 –
3
ch. 9 +
ch. 9 –
ch.10 +
ch.10 –
ch.11 +
ch.11 –
ch.12 +
ch.12 –
ch.13 +
ch.13 –
ch.14 +
ch.14 –
ch.15 +
ch.15 –
ch.16 +
ch.16 –
Connector Pin Assignment (CN1)
1 and 2, 48 and 49 in CN1 are connected.
The input is connected to the connector.
4
5
6
6
PIN NO.
ASSIGNMENT
PIN NO.
ASSIGNMENT
7
7
8
9
8
9
3
4
ch. 1 +
ch. 1 –
ch. 2 +
ch. 2 –
ch. 3 +
ch. 3 –
ch. 4 +
ch. 4 –
ch. 5 +
ch. 5 –
ch. 6 +
ch. 6 –
ch. 7 +
ch. 7 –
ch. 8 +
ch. 8 –
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
50
ch. 9 +
ch. 9 –
ch.10 +
ch.10 –
ch.11 +
ch.11 –
ch.12 +
ch.12 –
ch.13 +
ch.13 –
ch.14 +
ch.14 –
ch.15 +
ch.15 –
ch.16 +
ch.16 –
10
27
26
29
28
31
30
33
32
10
27
26
29
28
31
30
33
32
5
6
7
8
9
10
27
26
29
28
31
30
33
32
11 – 25 and 50 (CN1, CN2): Unused
34 – 37 (CN1): Unused
http://www.m-system.co.jp/
18KBXC SPECIFICATIONS
ES-0492 Rev.0 Page 5/6
MODEL: 18KBXC
Specifications are subject to change without notice.
http://www.m-system.co.jp/
18KBXC SPECIFICATIONS
ES-0492 Rev.0 Page 6/6
相关型号:
©2020 ICPDF网 联系我们和版权申明