JFX1-CB-V [MSYSTEM]

Plug-in Signal Conditioners M-UNIT;
JFX1-CB-V
型号: JFX1-CB-V
厂家: M-SYSTEM    M-SYSTEM
描述:

Plug-in Signal Conditioners M-UNIT

文件: 总4页 (文件大小:108K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
MODEL: JFX1  
E: 0 – 16 mA DC (Input resistance 62.5 Ω)  
Plug-in Signal Conditioners M-UNIT  
F: 0 – 10 mA DC (Input resistance 100 Ω)  
G: 0 – 1 mA DC (Input resistance 1000 Ω)  
H: 10 – 50 mA DC (Input resistance 100 Ω)  
J: 0 – 10 μA DC (Input resistance 1000 Ω)  
K: 0 – 100 μA DC (Input resistance 1000 Ω)  
GW: -1 – +1 mA DC (Input resistance 1000 Ω)  
FW: -10 – +10 mA DC (Input resistance 100 Ω)  
Z: Specify current (See INPUT SPECIFICATIONS)  
Voltage  
LINEARIZER  
(100-point field calibration)  
Functions & Features  
• Accepting non-linear input and providing a linearized  
output, proportional to the process variables  
• On-site calibration up to 100 points using a hand-held  
programmer PU-2x  
• Isolation up to 2000 V AC  
1: 0 – 10 mV DC (Input resistance 10 kΩ min.)  
15: 0 – 50 mV DC (Input resistance 10 kΩ min.)  
16: 0 – 60 mV DC (Input resistance 10 kΩ min.)  
2: 0 – 100 mV DC (Input resistance 100 kΩ min.)  
3: 0 – 1 V DC (Input resistance 1 MΩ min.)  
4: 0 – 10 V DC (Input resistance 1 MΩ min.)  
5: 0 – 5 V DC (Input resistance 1 MΩ min.)  
6: 1 – 5 V DC (Input resistance 1 MΩ min.)  
4W: -10 – +10 V DC (Input resistance 1 MΩ min.)  
5W: -5 – +5 V DC (Input resistance 1 MΩ min.)  
0: Specify voltage (See INPUT SPECIFICATIONS)  
• High-density mounting  
Typical Applications  
• V-notch weir  
• Gas analyzer  
• Irregular-shaped tank level input for volume calculation  
50  
(1.97)  
80  
(3.15)  
[2] OUTPUT  
Current  
127  
(5)  
A: 4 – 20 mA DC (Load resistance 750 Ω max.)  
B: 2 – 10 mA DC (Load resistance 1500 Ω max.)  
C: 1 – 5 mA DC (Load resistance 3000 Ω max.)  
D: 0 – 20 mA DC (Load resistance 750 Ω max.)  
E: 0 – 16 mA DC (Load resistance 900 Ω max.)  
F: 0 – 10 mA DC (Load resistance 1500 Ω max.)  
G: 0 – 1 mA DC (Load resistance 15 kΩ max.)  
Z: Specify current (See OUTPUT SPECIFICATIONS)  
Voltage  
mm (inch)  
MODEL: JFX1–[1][2]–[3][4]  
ORDERING INFORMATION  
• Code number: JFX1-[1][2]-[3][4]  
Specify a code from below for each of [1] through [4].  
(e.g. JFX1-6A-B/Q)  
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)  
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)  
3: 0 – 1 V DC (Load resistance 1000 Ω min.)  
4: 0 – 10 V DC (Load resistance 10 kΩ min.)  
5: 0 – 5 V DC (Load resistance 5000 Ω min.)  
6: 1 – 5 V DC (Load resistance 5000 Ω min.)  
4W: -10 – +10 V DC (Load resistance 10 kΩ min.)  
5W: -5 – +5 V DC (Load resistance 5000 Ω min.)  
0: Specify voltage (See OUTPUT SPECIFICATIONS)  
• Special input and output ranges (For codes Z & 0)  
• Linearization data (max. 100 points)  
Use Ordering Information Sheet (No. ESU-1621) to specify  
linearization data when I/O characteristics (max. 100  
points), function (ex. output = (input) ) or the I/O signals are  
2
nonlinear. Linear data will be programmed if not otherwise  
specified.  
• Specify the specification for option code /Q  
(e.g. /C01/S01)  
[3] POWER INPUT  
AC Power  
[1] INPUT  
Current  
B: 100 V AC  
C: 110 V AC  
A: 4 – 20 mA DC (Input resistance 250 Ω)  
A1: 4 – 20 mA DC (Input resistance 50 Ω)  
B: 2 – 10 mA DC (Input resistance 500 Ω)  
C: 1 – 5 mA DC (Input resistance 1000 Ω)  
D: 0 – 20 mA DC (Input resistance 50 Ω)  
D: 115 V AC  
F: 120 V AC  
G: 200 V AC  
H: 220 V AC  
JFX1 SPECIFICATIONS  
ES-1671 Rev.9 Page 1/4  
http://www.m-system.co.jp/  
MODEL: JFX1  
J: 240 V AC  
DC Power  
S: 12 V DC  
R: 24 V DC  
V: 48 V DC  
Offset: Max. 1.5 times span  
Input resistance  
Span 3 – 10 mV : ≥ 10 kΩ  
Span 10 – 100 mV : ≥ 10 kΩ  
Span 0.1 – 1 V : ≥ 100 kΩ  
Span ≥ 1 V : ≥ 1 MΩ  
[4] OPTIONS  
blank: none  
OUTPUT SPECIFICATIONS  
■ DC Current: 0 – 20 mA DC  
/Q: With options (specify the specification)  
Minimum span: 1 mA  
Offset: Max. 1.5 times span  
SPECIFICATIONS OF OPTION: Q (multiple selections)  
COATING (For the detail, refer to M-System's web site.)  
/C01: Silicone coating  
Load resistance: Output drive 15 V max.  
DC Voltage: -10 – +20 V DC  
Span: Min. 5 mV, max. 20 V  
/C02: Polyurethane coating  
Offset: Max. 1.5 times span  
/C03: Rubber coating  
Load resistance: Output drive 1 mA max.; at ≥ 0.5 V  
TERMINAL SCREW MATERIAL  
/S01: Stainless steel  
INSTALLATION  
Power input  
RELATED PRODUCTS  
• Programming Unit (model: PU-2x)  
AC: Operational voltage range: rating ±10 %,  
50/60 ±2 Hz, approx. 3 VA  
• PC configurator software (model: JXCON)  
Downloadable at M-System’s web site.  
A dedicated cable is required to connect the module to the  
PC. Please refer to the internet software download site or  
the users manual for the PC configurator for applicable  
cable types.  
DC: Operational voltage range: rating ±10 %  
ripple 10 %p-p max., approx. 3 W (125 mA at 24 V)  
Operating temperature: -5 to +55°C (23 to 131°F)  
Operating humidity: 30 to 90 %RH (non-condensing)  
Mounting: Surface or DIN rail  
Weight: 350 g (0.77 lb)  
GENERAL SPECIFICATIONS  
Construction: Plug-in  
PERFORMANCE in percentage of span  
Accuracy: ±0.1 % with segment gain ≤ 3  
[±0.1 % × gain] with segment gain > 3  
Connection: M3.5 screw terminals  
Screw terminal: Chromated steel (standard) or stainless  
steel  
Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)  
Response time: ≤ 0.5 sec. (0 – 90 %)  
Housing material: Flame-resistant resin (black)  
Isolation: Input to output to power  
Line voltage effect: ±0.1 % over voltage range  
Insulation resistance: ≥ 100 MΩ with 500 V DC  
Dielectric strength: 2000 V AC @1 minute (input to output  
to power to ground)  
Zero adjustment: -5 to +5 % (front)  
Span adjustment: 95 to 105 % (front)  
Linearization: 100 points max. within the range of -15.00 –  
+115.00 % input or output; represented as percentage of  
full-scale  
Adjustments: Programming Unit (model: PU-2x);  
linearization data, zero and span, simulating output, etc.  
(Refer to the users manual of JXCON for the adjustments  
configurable with JXCON.)  
INPUT SPECIFICATIONS  
DC Current:  
Shunt resistor attached to the input terminals (0.5 W)  
Specify input resistance value for code Z.  
DC Voltage: -300 – +300 V DC  
Minimum span: 3 mV  
JFX1 SPECIFICATIONS  
ES-1671 Rev.9 Page 2/4  
http://www.m-system.co.jp/  
MODEL: JFX1  
EXTERNAL DIMENSIONS unit: mm (inch)  
CLAMP  
(top & bottom)  
7.8 (.31)  
DIN RAIL  
35mm wide  
6
5
4
3
2–4.5 (.18) dia.  
MTG HOLE  
15 (.59) deep  
7
8
1
2
8–M3.5  
SCREW  
50 (1.97)  
107 (4.21)  
127 (5)  
40 (1.57)  
50 (1.97)  
[3.3 (.13)]  
• When mounting, no extra space is needed between units.  
TERMINAL ASSIGNMENTS unit: mm (inch)  
INPUT RESISTOR  
(model: REM)  
6
5
4
3
7
8
1
2
Input shunt resistor attached  
for current input.  
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM  
Z
S
Isolation  
Low Drift  
Amplifier  
Digital  
Computation  
Output  
Driver  
+
3
4
5
6
1
2
7
8
+
*
INPUT  
R
OUTPUT  
POWER  
U(+)  
V(–)  
MODULAR JACK  
PU-2x  
SERIAL TRANSMISSION LINE  
Base Socket  
*Input shunt resistor attached for current input.  
JFX1 SPECIFICATIONS  
ES-1671 Rev.9 Page 3/4  
http://www.m-system.co.jp/  
MODEL: JFX1  
Specifications are subject to change without notice.  
JFX1 SPECIFICATIONS  
ES-1671 Rev.9 Page 4/4  
http://www.m-system.co.jp/  

相关型号:

JFX1-CC-B

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-B/Q

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-C

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-C/Q

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-D

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-D/Q

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-F

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-G

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-H

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-J

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-R

Plug-in Signal Conditioners M-UNIT
MSYSTEM

JFX1-CC-S

Plug-in Signal Conditioners M-UNIT
MSYSTEM