首页 |元器件品牌 | PCB在线计价/下单
首页 > KHS-H-2DH/Q

KHS-H-2DH/Q

更新时间：2024-10-29 22:46:59
品牌：MSYSTEM
描述：Plug-in Signal Conditioners K-UNIT

PDF下载

中文翻译

PCB计价

KHS-H-2DH/Q 概述

Plug-in Signal Conditioners K-UNIT

KHS-H-2DH/Q 数据手册

通过下载KHS-H-2DH/Q数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载
MODEL: KHS  
H: 10 – 50 mA DC (Input resistance 100 Ω)  
Plug-in Signal Conditioners K-UNIT  
J: 0 – 10 μA DC (Input resistance 1000 Ω)  
K: 0 – 100 μA DC (Input resistance 1000 Ω)  
GW: -1 – +1 mA DC (Input resistance 1000 Ω)  
FW: -10 – +10 mA DC (Input resistance 100 Ω)  
Z: Specify current (See INPUT SPECIFICATIONS)  
Voltage  
PEAK HOLD  
(isolated)  
Functions & Features  
• Track mode: the output follows proportionally to the input  
• Peak-hold mode: responds only to an increasing signal,  
holding the maximum value until a higher signal or a  
command to reset is received  
1: 0 – 10 mV DC (Input resistance 10 kΩ min.)  
15: 0 – 50 mV DC (Input resistance 10 kΩ min.)  
16: 0 – 60 mV DC (Input resistance 10 kΩ min.)  
2: 0 – 100 mV DC (Input resistance 100 kΩ min.)  
3: 0 – 1 V DC (Input resistance 1 MΩ min.)  
4: 0 – 10 V DC (Input resistance 1 MΩ min.)  
5: 0 – 5 V DC (Input resistance 1 MΩ min.)  
6: 1 – 5 V DC (Input resistance 1 MΩ min.)  
4W: -10 – +10 V DC (Input resistance 1 MΩ min.)  
5W: -5 – +5 V DC (Input resistance 1 MΩ min.)  
0: Specify voltage (See INPUT SPECIFICATIONS)  
• Minimum value (valley) hold selectable  
• Isolation up to 2000 V AC  
• High-density mounting  
Typical Applications  
• Monitoring peak power consumption  
50  
(1.97)  
[3] OUTPUT  
Current  
80  
(3.15)  
A: 4 – 20 mA DC (Load resistance 750 Ω max.)  
B: 2 – 10 mA DC (Load resistance 1500 Ω max.)  
C: 1 – 5 mA DC (Load resistance 3000 Ω max.)  
D: 0 – 20 mA DC (Load resistance 750 Ω max.)  
E: 0 – 16 mA DC (Load resistance 900 Ω max.)  
F: 0 – 10 mA DC (Load resistance 1500 Ω max.)  
G: 0 – 1 mA DC (Load resistance 15 kΩ max.)  
Z: Specify current (See OUTPUT SPECIFICATIONS)  
Voltage  
123  
(4.84)  
mm (inch)  
MODEL: KHS[1]-[2][3]–[4][5]  
ORDERING INFORMATION  
• Code number: KHS[1]-[2][3]-[4][5]  
Specify a code from below for each of [1] through [5].  
(e.g. KHSH-6A-B/Q)  
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)  
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)  
3: 0 – 1 V DC (Load resistance 100 Ω min.)  
4: 0 – 10 V DC (Load resistance 1000 Ω min.)  
5: 0 – 5 V DC (Load resistance 500 Ω min.)  
6: 1 – 5 V DC (Load resistance 500 Ω min.)  
4W: -10 – +10 V DC (Load resistance 2000 Ω min.)  
5W: -5 – +5 V DC (Load resistance 1000 Ω min.)  
0: Specify voltage (See OUTPUT SPECIFICATIONS)  
• Special input and output ranges (For codes Z & 0)  
• Specify the specification for option code /Q  
(e.g. /C01/S01)  
[1] HOLD FUNCTION  
H: Peak hold  
L: Valley hold  
[4] POWER INPUT  
AC Power  
[2] INPUT  
Current  
B: 100 V AC  
C: 110 V AC  
D: 115 V AC  
F: 120 V AC  
A: 4 – 20 mA DC (Input resistance 250 Ω)  
A1: 4 – 20 mA DC (Input resistance 50 Ω)  
B: 2 – 10 mA DC (Input resistance 500 Ω)  
C: 1 – 5 mA DC (Input resistance 1000 Ω)  
D: 0 – 20 mA DC (Input resistance 50 Ω)  
E: 0 – 16 mA DC (Input resistance 62.5 Ω)  
F: 0 – 10 mA DC (Input resistance 100 Ω)  
G: 0 – 1 mA DC (Input resistance 1000 Ω)  
G: 200 V AC  
H: 220 V AC  
J: 240 V AC  
DC Power  
S: 12 V DC  
KHS SPECIFICATIONS  
ES-3541 Rev.3 Page 1/3  
http://www.m-system.co.jp/  
MODEL: KHS  
R: 24 V DC  
Minimum span: 5 mV  
Offset: Max. 1.5 times span  
Load resistance: Output drive 10 mA max.; 5 mA for  
negative voltage output; at ≥ 0.5 V  
[5] OPTIONS  
blank: none  
/Q: With options (specify the specification)  
INSTALLATION  
Power input  
SPECIFICATIONS OF OPTION: Q (multiple selections)  
COATING (For the detail, refer to M-System's web site.)  
/C01: Silicone coating  
• AC: Operational voltage range: rating ±10 %,  
50/60 ±2 Hz, approx. 2 VA  
•DC: Operational voltage range: rating ±10 %,  
ripple 10 %p-p max., approx. 2 W (90 mA at 24 V)  
Operating temperature: -5 to +55°C (23 to 131°F)  
Operating humidity: 30 to 90 %RH (non-condensing)  
Mounting: Surface or DIN rail  
/C02: Polyurethane coating  
/C03: Rubber coating  
TERMINAL SCREW MATERIAL  
/S01: Stainless steel  
Weight: 400 g (0.88 lb)  
GENERAL SPECIFICATIONS  
Construction: Plug-in  
PERFORMANCE in percentage of span  
Accuracy: ±0.2 %  
Connection: M3.5 screw terminals  
Screw terminal: Chromated steel (standard) or stainless  
steel  
Temp. coefficient: ±0.02 %/°C (±0.01 %/°F)  
Response time: ≤ 0.5 sec. (0 – 90 %)  
Housing material: Flame-resistant resin (black)  
Isolation: Input to output to power  
Overrange output: Approx. -10 to +120 % at 1 – 5 V  
Zero adjustment: -5 to +5 % (front)  
Span adjustment: 95 to 105 % (front)  
Hold control: Holds when opening the terminals 5 – 6; tracks  
when closing them  
Line voltage effect: ±0.1 % over voltage range  
Insulation resistance: ≥ 100 MΩ with 500 V DC  
Dielectric strength: 2000 V AC @1 minute (input to output  
to power to ground)  
INPUT SPECIFICATIONS  
■ DC Current:  
Shunt resistor attached to the input terminals (0.5 W)  
Specify input resistance value for code Z.  
■ DC Voltage: -300 – +300 V DC  
Minimum span: 3 mV  
Offset: Max. 1.5 times span  
Input resistance  
Span 3 – 10 mV : ≥ 10 kΩ  
Span 10 – 100 mV : ≥ 10 kΩ  
Span 0.1 – 1 V : ≥ 100 kΩ  
Span ≥ 1 V : ≥ 1 MΩ  
■ HOLD CONTROL  
Contact rating: 5 V @1 mA  
Detection levels: ≤ 1.25 kΩ / 1 V at Track  
≥ 20 kΩ / 4 V at Hold  
OUTPUT SPECIFICATIONS  
■ DC Current: 0 – 20 mA DC  
Minimum span: 1 mA  
Offset: Max. 1.5 times span  
Load resistance: Output drive 15 V max.  
■ DC Voltage: -10 – +12 V DC  
KHS SPECIFICATIONS  
ES-3541 Rev.3 Page 2/3  
http://www.m-system.co.jp/  
MODEL: KHS  
EXTERNAL DIMENSIONS unit: mm (inch)  
CLAMP  
(top & bottom)  
7.8 (.31)  
DIN RAIL  
35mm wide  
6
5
4
3
2–  
4.5 (.18) dia.  
MTG HOLE  
15 (.59) deep  
7
8
1
2
8–  
M3.5  
SCREW  
50 (1.97)  
103 (4.06)  
123 (4.84)  
40 (1.57)  
50 (1.97)  
[3.3 (.13)]  
• When mounting, no extra space is needed between units.  
TERMINAL ASSIGNMENTS unit: mm (inch)  
INPUT RESISTOR  
(model: REM)  
6
5
4
3
7
8
1
2
Input shunt resistor attached  
for current input.  
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM  
Z
S
(10 bits)  
Isolation  
Low Drift  
Amplifier  
UP / DOWN  
Counter  
D / A  
Converter  
Output  
Driver  
+
–
1
2
7
8
+
3
4
5
6
Comparator  
*
INPUT  
R
OUTPUT  
POWER  
–
+V  
U(+)  
V(–)  
HOLD CONTROL  
Gate  
Oscillator  
Close: Track  
Open: Hold  
Base Socket  
*Input shunt resistor attached for current input.  
Specifications are subject to change without notice.  
KHS SPECIFICATIONS  
ES-3541 Rev.3 Page 3/3  
http://www.m-system.co.jp/  

KHS-H-2DH/Q 相关器件

型号 制造商 描述 价格 文档
KHS-H-2DJ MSYSTEM Plug-in Signal Conditioners K-UNIT 获取价格
KHS-H-2DJ/Q MSYSTEM Plug-in Signal Conditioners K-UNIT 获取价格
KHS-H-2DR MSYSTEM Plug-in Signal Conditioners K-UNIT 获取价格
KHS-H-2DR/Q MSYSTEM Plug-in Signal Conditioners K-UNIT 获取价格
KHS-H-2DS MSYSTEM Plug-in Signal Conditioners K-UNIT 获取价格
KHS-H-2DS/Q MSYSTEM Plug-in Signal Conditioners K-UNIT 获取价格
KHS-H-31B MSYSTEM Plug-in Signal Conditioners K-UNIT 获取价格
KHS-H-31B/Q MSYSTEM Plug-in Signal Conditioners K-UNIT 获取价格
KHS-H-31C MSYSTEM Plug-in Signal Conditioners K-UNIT 获取价格
KHS-H-31C/Q MSYSTEM Plug-in Signal Conditioners K-UNIT 获取价格

KHS-H-2DH/Q 相关文章

  • HARTING(浩亭)圆形连接器产品选型手册
    2024-10-31
    6
  • HYCON(宏康科技)产品选型手册
    2024-10-31
    6
  • GREEGOO整流二极管和晶闸管产品选型手册
    2024-10-31
    7
  • 西门子豪掷106亿美元，战略收购工程软件巨头Altair
    2024-10-31
    8

    • 热门型号

  • LM358
  • UPC8158
  • XC6105A618
  • 2N5087/D28Z
  • TMM-136-06-S-S-SM-23-P
  • NC7WZ16P6X
  • SDR10KSM
  • STC53K33N07
  • ERG3SG242
  • M2XRP2-J1Z1-R
  • TMM-139-01-G-S-SM
  • 54F20
  • TMP513
  • SZ6A11
  • PEL12S
  • 概述
  • 数据手册
    • 2024 ICPDF网 联系我们和版权申明:QQ 272164286