KHS-H-B3G/Q 概述
Plug-in Signal Conditioners K-UNIT
KHS-H-B3G/Q 数据手册
通过下载KHS-H-B3G/Q数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MODEL: KHS
H: 10 – 50 mA DC (Input resistance 100 Ω)
Plug-in Signal Conditioners K-UNIT
J: 0 – 10 μA DC (Input resistance 1000 Ω)
K: 0 – 100 μA DC (Input resistance 1000 Ω)
GW: -1 – +1 mA DC (Input resistance 1000 Ω)
FW: -10 – +10 mA DC (Input resistance 100 Ω)
Z: Specify current (See INPUT SPECIFICATIONS)
Voltage
PEAK HOLD
(isolated)
Functions & Features
• Track mode: the output follows proportionally to the input
• Peak-hold mode: responds only to an increasing signal,
holding the maximum value until a higher signal or a
command to reset is received
1: 0 – 10 mV DC (Input resistance 10 kΩ min.)
15: 0 – 50 mV DC (Input resistance 10 kΩ min.)
16: 0 – 60 mV DC (Input resistance 10 kΩ min.)
2: 0 – 100 mV DC (Input resistance 100 kΩ min.)
3: 0 – 1 V DC (Input resistance 1 MΩ min.)
4: 0 – 10 V DC (Input resistance 1 MΩ min.)
5: 0 – 5 V DC (Input resistance 1 MΩ min.)
6: 1 – 5 V DC (Input resistance 1 MΩ min.)
4W: -10 – +10 V DC (Input resistance 1 MΩ min.)
5W: -5 – +5 V DC (Input resistance 1 MΩ min.)
0: Specify voltage (See INPUT SPECIFICATIONS)
• Minimum value (valley) hold selectable
• Isolation up to 2000 V AC
• High-density mounting
Typical Applications
• Monitoring peak power consumption
50
(1.97)
[3] OUTPUT
Current
80
(3.15)
A: 4 – 20 mA DC (Load resistance 750 Ω max.)
B: 2 – 10 mA DC (Load resistance 1500 Ω max.)
C: 1 – 5 mA DC (Load resistance 3000 Ω max.)
D: 0 – 20 mA DC (Load resistance 750 Ω max.)
E: 0 – 16 mA DC (Load resistance 900 Ω max.)
F: 0 – 10 mA DC (Load resistance 1500 Ω max.)
G: 0 – 1 mA DC (Load resistance 15 kΩ max.)
Z: Specify current (See OUTPUT SPECIFICATIONS)
Voltage
123
(4.84)
mm (inch)
MODEL: KHS[1]-[2][3]–[4][5]
ORDERING INFORMATION
• Code number: KHS[1]-[2][3]-[4][5]
Specify a code from below for each of [1] through [5].
(e.g. KHSH-6A-B/Q)
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)
3: 0 – 1 V DC (Load resistance 100 Ω min.)
4: 0 – 10 V DC (Load resistance 1000 Ω min.)
5: 0 – 5 V DC (Load resistance 500 Ω min.)
6: 1 – 5 V DC (Load resistance 500 Ω min.)
4W: -10 – +10 V DC (Load resistance 2000 Ω min.)
5W: -5 – +5 V DC (Load resistance 1000 Ω min.)
0: Specify voltage (See OUTPUT SPECIFICATIONS)
• Special input and output ranges (For codes Z & 0)
• Specify the specification for option code /Q
(e.g. /C01/S01)
[1] HOLD FUNCTION
H: Peak hold
L: Valley hold
[4] POWER INPUT
AC Power
[2] INPUT
Current
B: 100 V AC
C: 110 V AC
D: 115 V AC
F: 120 V AC
A: 4 – 20 mA DC (Input resistance 250 Ω)
A1: 4 – 20 mA DC (Input resistance 50 Ω)
B: 2 – 10 mA DC (Input resistance 500 Ω)
C: 1 – 5 mA DC (Input resistance 1000 Ω)
D: 0 – 20 mA DC (Input resistance 50 Ω)
E: 0 – 16 mA DC (Input resistance 62.5 Ω)
F: 0 – 10 mA DC (Input resistance 100 Ω)
G: 0 – 1 mA DC (Input resistance 1000 Ω)
G: 200 V AC
H: 220 V AC
J: 240 V AC
DC Power
S: 12 V DC
KHS SPECIFICATIONS
ES-3541 Rev.3 Page 1/3
http://www.m-system.co.jp/
MODEL: KHS
R: 24 V DC
Minimum span: 5 mV
Offset: Max. 1.5 times span
Load resistance: Output drive 10 mA max.; 5 mA for
negative voltage output; at ≥ 0.5 V
[5] OPTIONS
blank: none
/Q: With options (specify the specification)
INSTALLATION
Power input
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
• AC: Operational voltage range: rating ±10 %,
50/60 ±2 Hz, approx. 2 VA
•DC: Operational voltage range: rating ±10 %,
ripple 10 %p-p max., approx. 2 W (90 mA at 24 V)
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
/C02: Polyurethane coating
/C03: Rubber coating
TERMINAL SCREW MATERIAL
/S01: Stainless steel
Weight: 400 g (0.88 lb)
GENERAL SPECIFICATIONS
Construction: Plug-in
PERFORMANCE in percentage of span
Accuracy: ±0.2 %
Connection: M3.5 screw terminals
Screw terminal: Chromated steel (standard) or stainless
steel
Temp. coefficient: ±0.02 %/°C (±0.01 %/°F)
Response time: ≤ 0.5 sec. (0 – 90 %)
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Overrange output: Approx. -10 to +120 % at 1 – 5 V
Zero adjustment: -5 to +5 % (front)
Span adjustment: 95 to 105 % (front)
Hold control: Holds when opening the terminals 5 – 6; tracks
when closing them
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
INPUT SPECIFICATIONS
■ DC Current:
Shunt resistor attached to the input terminals (0.5 W)
Specify input resistance value for code Z.
■ DC Voltage: -300 – +300 V DC
Minimum span: 3 mV
Offset: Max. 1.5 times span
Input resistance
Span 3 – 10 mV : ≥ 10 kΩ
Span 10 – 100 mV : ≥ 10 kΩ
Span 0.1 – 1 V : ≥ 100 kΩ
Span ≥ 1 V : ≥ 1 MΩ
■ HOLD CONTROL
Contact rating: 5 V @1 mA
Detection levels: ≤ 1.25 kΩ / 1 V at Track
≥ 20 kΩ / 4 V at Hold
OUTPUT SPECIFICATIONS
■ DC Current: 0 – 20 mA DC
Minimum span: 1 mA
Offset: Max. 1.5 times span
Load resistance: Output drive 15 V max.
■ DC Voltage: -10 – +12 V DC
KHS SPECIFICATIONS
ES-3541 Rev.3 Page 2/3
http://www.m-system.co.jp/
MODEL: KHS
EXTERNAL DIMENSIONS unit: mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
6
5
4
3
2–
4.5 (.18) dia.
MTG HOLE
15 (.59) deep
7
8
1
2
8–
M3.5
SCREW
50 (1.97)
103 (4.06)
123 (4.84)
40 (1.57)
50 (1.97)
[3.3 (.13)]
• When mounting, no extra space is needed between units.
TERMINAL ASSIGNMENTS unit: mm (inch)
INPUT RESISTOR
(model: REM)
6
5
4
3
7
8
1
2
Input shunt resistor attached
for current input.
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Z
S
(10 bits)
Isolation
Low Drift
Amplifier
UP / DOWN
Counter
D / A
Converter
Output
Driver
+
–
1
2
7
8
+
3
4
5
6
Comparator
*
INPUT
R
OUTPUT
POWER
–
+V
U(+)
V(–)
HOLD CONTROL
Gate
Oscillator
Close: Track
Open: Hold
Base Socket
*Input shunt resistor attached for current input.
Specifications are subject to change without notice.
KHS SPECIFICATIONS
ES-3541 Rev.3 Page 3/3
http://www.m-system.co.jp/
KHS-H-B3G/Q 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
KHS-H-B3H | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KHS-H-B3H/Q | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KHS-H-B3J | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KHS-H-B3J/Q | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KHS-H-B3R | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KHS-H-B3R/Q | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KHS-H-B3S | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KHS-H-B3S/Q | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KHS-H-B4B | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 | |
KHS-H-B4B/Q | MSYSTEM | Plug-in Signal Conditioners K-UNIT | 获取价格 |
KHS-H-B3G/Q 相关文章
- 2024-10-31
- 6
- 2024-10-31
- 6
- 2024-10-31
- 7
- 2024-10-31
- 8