KMM-6D-J/Q [MSYSTEM]
Plug-in Signal Conditioners K-UNIT;
| 型号： | KMM-6D-J/Q |
| 厂家： | 
M-SYSTEM |
| 描述： | Plug-in Signal Conditioners K-UNIT |
| 文件： | 总3页 (文件大小：93K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: KMM
5: 0 – 5 V DC (Load resistance 500 Ω min.)
Plug-in Signal Conditioners K-UNIT
6: 1 – 5 V DC (Load resistance 500 Ω min.)
4W: -10 – +10 V DC (Load resistance 2000 Ω min.)
5W: -5 – +5 V DC (Load resistance 1000 Ω min.)
0: Specify voltage (See OUTPUT SPECIFICATIONS)
ANALOG MULTIPLIER
Functions & Features
• Provides a DC output proportional to the product of two
input signals
[2] POWER INPUT
AC Power
• Non-isolated two inputs
• High-density mounting
B: 100 V AC
C: 110 V AC
D: 115 V AC
F: 120 V AC
G: 200 V AC
H: 220 V AC
J: 240 V AC
• 2000 V AC isolation
50
(1.97)
80
(3.15)
DC Power
S: 12 V DC
R: 24 V DC
123
(4.84)
mm (inch)
[3] OPTIONS
blank: none
/Q: With options (specify the specification)
MODEL: KMM–6[1]–[2][3]
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
ORDERING INFORMATION
• Code number: KMM-6[1]-[2][3]
Specify a code from below for each of [1] through [3].
(e.g. KMM-6A-B/Q)
/C02: Polyurethane coating
/C03: Rubber coating
• Special output range (For codes Z & 0)
• Specify the specification for option code /Q
(e.g. /C01/S01)
TERMINAL SCREW MATERIAL
/S01: Stainless steel
GENERAL SPECIFICATIONS
Construction: Plug-in
INPUT
Voltage
Connection: M3.5 screw terminals
Screw terminal: Chromated steel (standard) or stainless
steel
6: 1 – 5 V DC (Input resistance 1 MΩ min.)
[1] OUTPUT
Current
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Overrange output: 0 to 120 % at 1 – 5 V
Zero adjustment: -5 to +5 % (front)
Span adjustment: 95 to 105 % (front)
A: 4 – 20 mA DC (Load resistance 750 Ω max.)
B: 2 – 10 mA DC (Load resistance 1500 Ω max.)
C: 1 – 5 mA DC (Load resistance 3000 Ω max.)
D: 0 – 20 mA DC (Load resistance 750 Ω max.)
E: 0 – 16 mA DC (Load resistance 900 Ω max.)
F: 0 – 10 mA DC (Load resistance 1500 Ω max.)
G: 0 – 1 mA DC (Load resistance 15 kΩ max.)
Z: Specify current (See OUTPUT SPECIFICATIONS)
Voltage
Equation: Y
where Y
, X
0
= X
1
× X
2
0
: output (0 – 100 %)
: input (0 – 100 %)
X1
2
Note) Be aware that a input signal less than 0 % is
calculated as a minus signal.
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)
3: 0 – 1 V DC (Load resistance 100 Ω min.)
4: 0 – 10 V DC (Load resistance 1000 Ω min.)
OUTPUT SPECIFICATIONS
■ DC Current: 0 – 20 mA DC
Minimum span: 1 mA
KMM SPECIFICATIONS
ES-3645 Rev.3 Page 1/3
http://www.m-system.co.jp/
MODEL: KMM
Offset: Max. 1.5 times span
Load resistance: Output drive 15 V max.
■ DC Voltage: -10 – +12 V DC
Minimum span: 5 mV
Offset: Max. 1.5 times span
Load resistance: Output drive 10 mA max.; 5 mA for
negative voltage output; at ≥ 0.5 V
INSTALLATION
Power input
• AC: Operational voltage range: rating ±10 %,
50/60 ±2 Hz, approx. 2 VA
•DC: Operational voltage range: rating ±10 %,
ripple 10 %p-p max., approx. 2 W (80 mA at 24 V)
Operating temperature: -5 to +55°C (23 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Weight: 350 g (0.77 lb)
PERFORMANCE in percentage of span
Accuracy: ±0.2 %
Temp. coefficient: ±0.03 %/°C (±0.02 %/°F)
Response time: ≤ 0.5 sec. (0 – 90 %)
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input to output
to power to ground)
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
6
5
4
3
2–
4.5 (.18) dia.
MTG HOLE
15 (.59) deep
7
8
1
2
8–
M3.5
SCREW
50 (1.97)
103 (4.06)
123 (4.84)
40 (1.57)
50 (1.97)
[3.3 (.13)]
• When mounting, no extra space is needed between units.
KMM SPECIFICATIONS
ES-3645 Rev.3 Page 2/3
http://www.m-system.co.jp/
MODEL: KMM
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
Z
S
Isolation
Input
Circuit
Output
Driver
+
–
+
–
+
3
4
5
6
Multiplier
1
2
7
8
INPUT 1 (X
1
2
)
)
OUTPUT (Y
0)
–
Input
Circuit
U(+)
V(–)
INPUT 2 (X
POWER
Base Socket
Specifications are subject to change without notice.
KMM SPECIFICATIONS
ES-3645 Rev.3 Page 3/3
http://www.m-system.co.jp/
相关型号：
©2020 ICPDF网 联系我们和版权申明