MODEL: KYPD
■ Voltage pulse waveform
GENERAL SPECIFICATIONS
Construction: Plug-in
Volts
50V max.
Connection: M3.5 screw terminals
Screw terminal: Chromated steel (standard) or stainless
steel
Amplitude
Vinp-p
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Excitation adjustment: 5 – 12 V DC
Detecting level adjustments (DC voltage pulse): 2 – 10 V
Input pulse sensing: DC coupled
DC Offset
t
OUTPUT SPECIFICATIONS
■ Open Collector: 50 V DC @ 50 mA (resistive load)
Input filter: Provided with output code A2, M2, N2, H
(time constant approx. 1 msec.)
Maximum frequency:
Output code A1: 100 kHz with load resistance ≤ 1 kΩ
OUtput code A2: 10 Hz with load resistance ≤ 1 kΩ
Saturation voltage: 0.5 V DC
INPUT SPECIFICATIONS
Excitation: Shortcircuit protection; approx. 150 mA at
shortcircuit
■ Voltage Pulse: Rating (5 or 12 V) ± 10 %
Maximum frequency: 100 kHz
■ Dry Contact
Max. frequency: 100 kHz
Load resistance: 1.5 kΩ min. for 5 V, 3 kΩ min. for 12 V
L level: ≤ 0.5 V
Pulse width time requirement: 5 μsec. min. (10 ms
for output code A2, M2, N2, H)
Sensing: 10 V DC @ 2.5 mA
■ Relay Contact: 120 V AC or 30 V DC @ 200 mA
(resistive load)
ON/OFF level:
Maximum switching voltage: 250 V AC or 30 V DC
Maximum switching power: 50 VA or 6 W
Minimum load: 5 V DC @ 10 mA
≥ 5.5 kΩ /5.5 V for OFF
≤ 1.8 kΩ /4.5 V for ON
■ Voltage Pulse: Specify DC offset and amplitude.
Max. frequency: 100 kHz
Maximum frequency: 0.5 Hz
Relay life:
Pulse width time requirement: 5 μsec. min. (10 ms
for output code A2, M2, N2, H)
Waveform: Square or sine
2 × 10
7
cycles (mechanical)
cycles (electrical)
7 × 10
6
Input impedance: 10 kΩ min.
Input amplitude: 2 – 50 Vp-p
Sensitivity adjustment (threshold level): 2 – 10 V
Max. voltage between input terminals: 50 V
• 5V, 12V, 24V Pulse
OUTPUT PULSE WIDTH
•Equal to the Input: No pulse width conversion
(difference between input and output within ±10 μsec.)
• One-shot Output: Constant pulse width
Output Frequency (Hz) = 500 / (Output Pulse Width (msec.))
Adjustable pulse width
Waveform: Square or sine
Input impedance: 10 kΩ min.
Detecting level
Pulse width max. 30 msec. (code 2):
1 – 30 msec. adjustable (standard 5 msec. ±20 %) for
'Output' code other than 'H'
INPUT 5 V PULSE 12 V / 24 V PULSE
V
H
≥ 2.25 V
≤ 1.75 V
≥ 5.25 V
≤ 4.75 V
10 – 30 msec. adjustable (standard 10 msec. ±20 %) for
'Output' code 'H'
VL
■ Two-wire Current Pulse
Pulse width min. 30 msec. (code 3): 30 msec. – 1 sec.
adjustable (standard 50 msec. ±20 %)
Max. frequency: 100 kHz
Pulse width time requirement: 5 μsec. min. (10 ms
for output code A2, M2, N2, H)
Input resistance: Receiving resistor 220 Ω
Maximum current: ± 50 mA
Hi/Lo level: ≤ 5 mA for Lo, ≥ 15 mA for Hi
KYPD SPECIFICATIONS
ES-3576 Rev.13 Page 2/6
http://www.m-system.co.jp/